The presence of exogenous auxins such as indole-3-acetic acid (IAA), has been reported in organic materials such as vermicompost. The objectives of this work were to quantify the concentration of IAA in sand-based substrates with vermicompost (S-VC), to establish the relationship between the concentration of exogenous IAA and the amount of vermicompost (VC), as well as determine its influence on the development of tomato plants. S-VC substrates with different percentages based on volume (0, 20, 40 and 50% VC) placed in pots were used to transplant tomato seedlings. In each substrate, the concentration of IAA was determined at the beginning and at the end of a culture cycle, as well as the bacterial load. In addition, some performance components were measured in the plants. The results show that by increasing 1 kg of VC in a sand-based substrate, the concentration of exogenous IAA increases both at the beginning and at the end of the experiment (0.0470 and 0.0642 mg g^-1, respectively); a result that, in turn, was related to the colony-forming units of gram-positive bacteria (Bacillus spp., mainly). Behavior that is reflected in tomato plants; for example, the root had its maximum development (371.33 cm^-3) when the amount of VC in the substrate was 4.12 kg.

With the ever-growing geopolitical tensions across borders arising, ultimately from the eternal energy needs, it is the peak time for humanity to put its reliance on a more quasi-perpetuity source of energy, such as the Sun. Even though current photovoltaics are the frontier of solar power harvesting, their efficiencies are reaching a state of stasis sooner or later. The efficiencies of single-junction solar cells are capped by the Shockley-Quiesser limit of 33.7%. Researchers are racing toward a way to beat this limit while keeping the Levelized Cost of Energy (LCE) to its minimum. Amongst all contenders, rectenna (or rectifying antenna), which was invented only a decade after the first practical PV cell by the Bells lab [1], is the most promising technology to take the forefront in quenching the energy needs, not only because of the absence of any such theoretical limit but also a lower cost of production. This report will review three state-of-the-art architectures for optical rectification developed by the leading groups worldwide. The review will compile a concise discussion on Metal-Double-Insulator-Metal diodes, CNT-Insulator-Metal diodes, and Point-contact-Metal-Insulator-Metal diodes, with an elaborative focus on their fabrication methods and results obtained.

In this article, metallic additive manufacturing (AM) processes were classified and demonstrated. AM technology can be applied to a wide range of industrial areas because of its great feasibility in the design and manufacturing of various complex parts. The main factor that distinguishes various metallic AM processes from each other is the deposition method. Deposited metal can be imported in the form of melt or semi-solid. AM technology also covers a wide range of materials like aluminum, titanium, and many other alloys. Some of the common applications of metallic AM processes are the quick manufacturing of the parts which utilized in various industries like medical, automotive, aerospace, and jewelry industries. AM can help to fabricate parts that are impossible to be manufactured by other processes.

Metal-reinforced polymethyl-methacrylate (PMMA) is considered the gold standard material for immediate loading on dental implants. However, mechanical problems under loading cycles can occur, such as fractures. To overcome these drawbacks, a novel polymer-based material has been proposed. The aim of the present in vitro comparative research is to validate a novel composite polymer developed to replace metal-reinforced PMMA interim restoration due to its advantages of good mechanical proprieties, easier manufacturing, and handling. Ten interim restorations were CAD/CAM designed and fabricated (five in the composite "ONLY" group, and five in the metal-reinforced PMMA group). All the samples were screwed into the prototype models, simulating a complete edentulous mandible rehabilitated with six straight implants. Outcome measures were breakpoint (load, N) and displacement (mm) thought a static, compression test and material behavior under dynamic cyclic test method (fatigue test). A total of twenty samples were tested. Ten samples were used for each test (10 for static and 10 for dynamic), five samples were used in each group (test and control). All the specimens completed the mechanical tests, as planned. There was no statistically significant difference between groups for all, breakpoint, displacement and fatigue tests. Breakpoint in the test group was 1953.19 ± 543.73 N, while, it was 2031.10 ± 716.68 N in the control group, with no statistically significant difference (P=0.775). The displacement was 1.89 ± 0.34 mm in the test group and 1.98 ± 0.75 mm in the control group, again, with no statistically significant difference (P=0.763). Under dynamic cyclic test method, in the control group the mean load was 2504.6 ± 972.15 N, while, in the test group the mean load was 3382 ± 578.5 N. The difference between group was 877.4 ± 579.3 N (p value=0.121). With the limitation of this in vitro study, the novel composite polymer can be used to immediately load dental implants. Further clinical researches are needed to confirm this preliminary results.

We revisit the argument that link the efficiency of a solar cell to its reverse operation as a LED, in the case where the material is organic. In organic cells, exciton transport is an intermediate process between sunlight absorption and the generation of electric current. We show that quenching exciton radiation can be beneficial to cell efficiency, without contradicting the general rule prevailing for semiconductor cells. Our treatment allows us to discuss both bulk heterojunction and planar junctions.

In an attempt to reuse fibrous textile waste and, at the same time, to address dye pollution in textile wastewater, waste cotton-based yarn was utilized as both a cheap and sustainable adsorbent and a precursor for carbon adsorbent production. Cotton and cotton/polyester yarn samples underwent thermal modification through carbonization followed by chemical activation with KOH. Various techniques including nitrogen adsorption-desorption isotherms, scanning electron microscopy, Fourier transform infrared spectroscopy, and surface charge determination were employed to analyze the morphological and surface properties of the cotton-based adsorbents. Adsorption properties were evaluated by testing the removal of selected cationic and anionic dyes from water. The impact of temperature, contact time, initial concentration, and pH of the adsorbate solution on adsorption was investigated, with experimental data analyzed using theoretical models. While carbonization alone did not significantly enhance adsorption properties, activated samples exhibited high efficacy in removing both cationic and anionic dyes from water. Despite the negative influence of the polyester component in the carbon precursor on the efficiency of activated samples in removing methyl orange, results indicated that activated cotton and cotton/polyester yarn could be used to prepare highly efficient adsorbents for the rapid removal of methylene blue from real wastewater samples.

Fine chemicals are produced in small annual volume batch processes (often <10,000 tonnes per year), with a high associated price (usually > $10/kg). As a result of their usage in the production of speciality chemicals, in areas including agrochemicals, fragrances and pharmaceuticals, their necessity will remain high for the foreseeable future. This review article assesses current methods used to produce fine chemicals with heterogeneous catalysts, including both well-established methods as well as newer experimental methods. A wide range of methods utilising microporous and mesoporous catalysts has been explored, including their preparation and modification before use in industry. Their potential drawbacks, as well as benefits, have been analysed, with their feasibility compared to newer, recently emerging catalysts. The field of heterogeneous catalysis for fine chemical production is a dynamic and ever-changing area of research. This deeper insight into catalytic behaviour and material properties will produce more efficient, selective, and sustainable processes in the fine chemical industry. The findings from this article will provide an excellent foundation for further exploration and a critical review in this field of fine chemical production using micro- and mesoporous heterogeneous catalysts.

This study presents the encapsulation of two amino acid-based ionic liquids (AAILs), 1-Ethyl-3-methylimidazolium glycine [Emim][Gly] and 1-Ethyl-3-methylimidazolium alanine [Emim][Ala], in a highly porous metal organic framework (MOF-177), to generate state-of-the-art composites for post-combustion CO2 capture. The thermogravimetric analysis (TGA) demonstrated a successful encapsulation of the AAILs, consequently dramatically reducing the composites' surface area and pore volume. Both [Emim] [Gly]@MOF-177 and [Emim][Ala]@MOF-177 had close to 3 times the CO2 uptake of MOF-177 at 20 wt.% loading, 0.2 bar, and 303 K. Additionally, 20-[Emim][Gly]@MOF-177 and 20-[Emim] [Ala]@MOF-177 enhanced their CO2/N2 selectivity from 5 (pristine MOF-177) to 13 and 11, respectively.

We report on the effects of the film morphology on the fluorescence spectra for a thin film including a quinoxaline-based co-polymer (TQ1) and a fullerene derivative (PC₇₀BM). The ratio between the polymer and the fullerene derivative, as well as the processing solvent were varied. Beside the main emission peak at 700 nm in the fluorescence spectra of thin films of this phase-separated blend, a broad emission band is observed with a maximum at 520 - 550 nm. The intensity of this emission band decreases with an increasing degree of mixing in the film and becomes most prominent in thicker films, films with high PC₇₀BM content, and films that were spin-coated from solvents with lower PC₇₀BM solubility. We assign this emission band to aggregated PC₇₀BM.

The objectives of this study are threefold. First, we evaluate the applicability of the information–motivation–behavioral skills (IMB) model for predicting organic food purchase intention (OFPI) in adults with chronic conditions. Second, we examine the indirect effects of organic food knowledge, attitudes toward organic food purchase, and subjective norms on OFPI through self-efficacy. Third, we examine whether these indirect effects are moderated by gender and educational attainment. Data were collected from Indian adults with chronic conditions using a self-administered questionnaire. The results show significant indirect effects of organic food knowledge, attitude toward organic food purchase, and subjective norm on OFPI through self-efficacy. Moreover, the mediating effect of knowledge was moderated by gender and education attainment, with the effect being stronger for females and among individuals with a lower level of education. Organic food marketers, social marketers, and public health agencies promoting organic food consumption to people with chronic conditions should aim to increase their confidence in comprehending organic food. This study contributes to the literature by assessing the applicability of Fisher and Fisher’s (1992) IMB model in understanding behavioral intention toward organic food.

Dimers and oligomers of alkenes represent a category of compounds that are in great demand for diverse industrial sectors. Among the developing synthetic methods, the catalysis of alkene dimerization and oligomerization using transition metal salts and complexes is of undoubted interest for practical application. This approach demonstrates substantial potential, offering not only elevated reaction rates but also precise control over the chemo-, regio-, and stereoselectivity of the reactions. In this review, we discuss the data on catalytic systems for alkene dimerization and oligomerization. Our focus lies in the analysis of how the activity and chemoselectivity of these catalytic systems are influenced by various factors, such as the nature of the transition metal, the ligand environment, the activator, and substrate structure. Notably, the review particularly discusses the reaction mechanisms, encompassing metal complex activation, structural and dynamic features, and the reactivity of hydride intermediates, which serve as potential catalytically active centers in alkene dimerization and oligomerization.

Herein, a novel cavity design of racetrack integrated circular cavity established on metal-insulator-metal (MIM) waveguide is suggested for refractive index sensing application. Over the past few years, we have witnessed several unique cavity designs to improve the sensing performance of the plasmonic sensors created on the MIM waveguide. The optimized cavity design can provide the best sensing performance. In this work, we have numerically analyzed the device design by utilizing the finite element method (FEM). The small variations in the geometric parameter of the device can bring a significant shift in the sensitivity and FOM of the device. The best sensitivity and FOM of the anticipated device are 1400 nm/RIU and ~12.01, respectively. We believe that the sensor design analyzed in this work can be utilized in the on-chip detection of biochemical analytes.

This review delves into the pivotal role of green manure in advancing agricultural sustainability and enhancing soil fertility. It emphasizes the wide-ranging ecological benefits of green manure practices, particularly in tropical regions, where it fosters multiple biological processes such as nitrogen fixation and nutrient cycling. The text provides an in-depth exploration of specific green manure species, their characteristics, practical considerations, and the physical, biological, and chemical effects they have on soil. It also discusses the practical implementation of green manure techniques, including cropping, intercropping, and strip or alley cultivation. The study emphasizes the critical need for species selection and effective green manure management, shedding light on their profound impact on crop productivity and environmental sustainability. With comprehensive details on various species and their practical implications, the study offers a comprehensive understanding of green manure's potential as an alternative source to mineral fertilizers in tropical agriculture.

Research indicates that farmers’ demographic characteristics and production practices have safety and health implications. However, current systems do not identify organic farmers independently from conventional farmers, and literature on how organic and conventional farmers compare is very limited. We conducted a secondary analysis of 2012 Census of Agriculture data to compare organic and non-organic farms and principal operators (POs) in New Mexico (NM). Organic farms were smaller in size, and POs of farms with organic sales were significantly younger (55.8±9.5 vs. 60.5±5.5 years) and less experienced (19.5±6.8 vs. 25.2±6.8 years). Significant differences were also found in POs ethnicity, race, and primary occupation. More farms with organic sales had a female PO compared to farms with non-organic sales (27% vs. 19%). Other significant differences related to work arrangements, household income, living conditions, and access to Internet. National surveys and regional studies may not accurately typify and describe the local organic producer, which is essential in order to advance policy, develop health interventions, and properly address occupational safety and risk among organic farmers. This study makes a unique contribution to understanding the importance of surveillance and collecting place-based data that are specific to the organic producer.

Organic farming products are fast gaining acceptance from consumers all over the world due to the perceived belief that they are safe for human consumption. In recent years, there has been an increase in the levels of persistent organic and inorganic pollutants in the environment. These pollutants may be found in materials such as sewage sludge, treated wastewater, farmyard manure (human and animal feaces and urine) that are used for organic farming. The present review examined through literature the presence of these emerging pollutants in crops that are cultivated from farming activities practicing organic farming. The review highlighted and documented various pollutants that may be found in crops due to non-compliance with legislation establishing organic farming. The need to develop a robust method for identifying safe products from organic farming was highlighted. The impact of non-compliance and lack of proper education on the peasant farmers practicing backyard farming was also enumerated.

In a constantly changing environment brought about by the climate crisis and escalated anthropogenic perturbations driven by the growing population, harmful algal bloom dynamics and their impacts are expected to shift, necessitating adaptive management strategies and comprehensive research efforts. Similar to primary productivity, HABs have been thought to be driven primarily by major nutrients such as N, P, and Si. However, recent investigations on the role and importance of micronutrients as limiting factors in aquatic environments have been highlighted. This paper provides a review of metal and phytoplankton interactions, with a specific emphasis on pertinent information on the influence of trace nutrients on growth, toxin production, and other underlying mechanisms related to the dynamics of HABs. Low to near-depleted levels of essential nutrients including Fe, Cu, Zn, Se, Mn, Co, and Mo, negatively impact cell growth and proliferation of various marine and freshwater HAB species. However, evidence shows that at elevated levels, these trace elements along with other non-essential ones, could still cause toxic effects to certain HAB species manifested by decreased photosynthetic activities, oxidative stress, ultrastructure damage, and cyst formation. Interestingly, while elevated levels of these metals mostly result in increased toxin production, Co (i.e., yessotoxins, gymnodimine, and palytoxins) and Mn (i.e., isodomoic acid, okadaic and diol esters) enrichments revealed otherwise. In addition to toxin production, releasing dissolved organic matter (DOM) including dissolved organic carbon (DOC) and humic substances was observed as an adaptation strategy, since these organic compounds have been proven to chelate metals in the water column, thereby reducing metal-induced toxicity. Whilst current research center on free metal toxicity of specific essential elements such as in Cu and Zn, a comprehensive account of how trace metals contribute to the growth, toxin production, and other metabolic processes under conditions reflective of in-situ scenarios of HAB-prone areas, would yield new perspectives on the roles of trace metals in HABs. With the growing demands of the global population for food security and sustainability, substantial pressure is exerted on the agriculture and aquaculture sector, highlighting the need for effective communication of information regarding the interactions of macro- and micronutrients with HABs to improve existing policies and practices.

Electroless etching of semiconductors was elevated to an advanced micromachining process by the addition of a structured metal catalyst. Patterning of the catalyst by lithographic techniques facilitates the patterning of crystalline and polycrystalline wafer substrates. Galvanic deposition of metals on semiconductors has a natural tendency to produce nanoparticles rather than flat uniform films. This characteristic makes possible the etching of not only wafers but also particles with arbitrary shape. While it has been widely recognized that spontaneous deposition of metal nanoparticles can be used in connection with etching to porosify wafers, it is also possible to produced nanostructured powders. MACE can be controlled to produce (1) etch track pores with shapes and sizes closely related to the shape and size of the metal nanoparticle, (2) hierarchically porosified substrates exhibiting combinations of large etch track pores and mesopores, and (3) nanowires with either solid or mesoporous cores. This review discussed the mechanisms of porosification, processing advances and the properties of the etch product with special emphasis on the etching of silicon powders.

Serum transferrin (sTf) plays a pivotal role in regulating iron biodistribution and homeostasis within the body. The molecular details of sTf Fe(III) binding, blood transport, and cellular delivery through transferrin receptor-mediated endocytosis are generally well-understood. Emerging interest exists in exploring sTf complexation of nonferric metals as it facilitates the therapeutic potential and toxicity of several of them. This review explores recent X-ray structural and physiologically relevant metal speciation studies to understand how sTf partakes in the bioactivity of key non-redox active hard Lewis acidic metals. It challenges preconceived notions of sTf structure function correlations that were based exclusively on the Fe(III) model by revealing distinct coordination modalities that nonferric metal ions can adopt and different modes of binding to metal-free and Fe(III)-bound sTf that can directly influence how they enter into cells and, ultimately, how they may impact human health. This knowledge informs on biomedical strategies to engineer sTf as a delivery vehicle for metal-based diagnostic and therapeutic agents in the cancer field. It is the intention of this work to open new avenues for characterizing the functionality and medical utility of nonferric-bound sTf and to expand the significance of this protein in the context of bioinorganic chemistry.

This article will briefly review the progress of h-BN based solid-state metal semiconductor metal (MSM) neutron detectors. In the last decade, several groups have been working on hexagonal boron nitride (h-BN) based solid-state neutron detectors. Recently, the detection efficiency of 59% has been reported. Efficient, low-cost neutron detectors made from readily available materials are essential for various applications. Neutron detectors are widely used to detect fissile materials and nuclear power plants for security applications. The most common and widely used neutron detectors are 3He based, which are sometimes bulky, difficult to transport, have high absorption length, need relatively high bias voltage (>1000 V), and have low Q-value (0.764 MeV). Also, 3He is not readily available material. Thus, there is a strong need to find an alternative detection material. 10B isotope has a high neutron absorption cross-section, and it has been tested as a coating on the semiconducting materials. Due to the two-step process, neutron capture through 10B, and then electron-hole pair generation in a typical semiconducting material, the efficiency of these devices is not up to the mark. The progress in h-BN based detectors requires a review to envision the further improvement in this technology.

Using two metal insulated metal waveguides (MIM) and five resonator (a quadrilateral cavity and three rings with different dimensions), we design a plasmonic refractive index sensor. Using the time domain finite difference method, we examine and analyze the sensor performance (numerical analysis) and using the transmission line model method, we theoretically examine the performance of the sensor By summarizing these two methods and calculating the sensitivity coefficient S, quality coefficient Q and figure of merit (FOM), a plasmonic sensor with good performance is obtained. Using the supermods of the resonators, we will achieve a stable wavelength spectrum and a suitable and stable sensitivity coefficient spectrum. Challenges and changes that occur in different modes of this sensor will lead to a balanced and relatively good structure. This designed sensor can be useful in the development of integrated optical circuits.

In this paper, a plasmonic refractive index sensor based on metal insulated metal waveguide (MIM) with three rings and a resonant cavity is first proposed and numerically evaluated. Next, we add four teeth to the sensor structure. We study and simulate the resonant wavelengths and refractive index of resonators using the time difference finite difference method. Given that the sensor and the conduction characteristics of plasmonic waves are influenced by the structure parameters,Therefore, by changing the refractive index and changing the dimensions and coordinates of the cavity and rims, we can change the passage coefficient in the resonant modes and measure the sensor performance. As a result, we obtain the sensitivity coefficient, the figure of merit (FOM) and the quality factor Q of the sensor. We modulate the resonance wavelength FWHM using the generated modes and reach a sensitivity of 2166 nm / RIU. These plasmonic sensors with a simple framework and balanced performance and high optical resolution can be used to measure the refractive index in the medical, chemical and food industries.

In this study, we seek to analyze and numerically evaluate a plasmonic sensor. To form the sensor structure, we use several amplifiers, such as two rings attached to each other and a cavity, as well as two metal insulating metal waveguides (MIM). At the beginning of this simulation, we must examine the resonant wavelengths and the refractive index of the resonators using the finite difference time domain method. By changing the refractive index and changing the dimensions of the cavity and the rims, we seek to investigate the sensor performance and the conduction characteristics of the plasmonics and to obtain the effect of these parameters. To evaluate the sensor performance, we calculate the three factors of sensitivity coefficient S, quality factor Q and figure of merit (FOM), here we reach the sensitivity of 987.6 nm / RIU. Such a plasmonic sensor with a simple framework and high optical resolution can be very useful for sensor systems on optical circuits.

In recent years, many researchers have begun to shift their focus onto the synthesis of nanomaterials as this field possesses immense potential that may provide incredible technological advances in the near future. The downside of conventional synthesis techniques, such as co-precipitation, sol-gel and hydrothermal methods, is that they necessitate the use of toxic chemicals, produce harmful by-products and require a considerable amount of energy; therefore, more sustainable fabrication routes are sought after. Biological molecules have been previously utilised as precursors to nanoparticle synthesis, thus eliminating the negative factors involved in traditional methods. In addition, transition-metal nanoparticles possess a wide scope of applications due to their multiple oxidation states and large surface areas; thereby allowing for a higher reactivity when compared to their bulk counterpart and rendering them an interesting research topic. However, this field is still relatively unknown and unpredictable. Therefore, this review aims to obtain a better understanding on the plant-mediated synthesis process of the major transition-metal and transition-metal oxide nanoparticles, and how different parameters affect their unique properties.

Metal additive manufacturing (AM) has gained much attentions in recent years due to its advantages including geometric freedom and design complexity, appropriate to a wide range of potential industrial applications. However, conventional metal AM methods have high-cost barriers due to the initial cost of the capital equipment, support and maintenance, etc. This study presents a unique low-cost metal material extrusion (MME) technology. The filaments used have polylactic acid (PLA) as the matrix and metal powders (copper, bronze, stainless steel, high carbon iron, and aluminum) as reinforcements. Using the proposed fabrication technology, test specimens were built by extruding polymer/metal composite filaments, which were then sintered in an open-air furnace to produce solid metallic parts. In this research, the mechanical and thermal properties of the built parts are examined using tensile tests, thermogravimetric-, thermomechanical- and microstructural analysis.

Biochars are often proposed as a strategy for long-term carbon sequestration. Nevertheless, application of pyrolysed feedstock, particularly along with exogenous organic matter, may affect carbon dynamics in soil through introduction of labile carbon pools and stimulation of extracellular enzymes activity. The main aim of this research was to evaluate the influence of biochars and unprocessed organic amendments addition in two agricultural soils on the dissolved organic carbon (DOC) content and activity of three enzymes involved in carbon turnover. In the incubation experiment, activity of dehydrogenase, β-glucosidase, cellulase and DOC content were measured on day 30, 60, 90, 180 and 360. Addition of biochars stimulated the activity of dehydrogenase and β-glucosidase, while cellulase was suppressed. Fresh biomass amendment enhanced activity of the enzymes through priming effect. DOC content tended to be the highest in treatments with high enzyme activity, suggesting that DOC introduced with amendments acted as a source of energy for microbes. Our findings support the hypothesis that biochar properties and presence of exogenous organic matter affect microbial response in soil, what might be crucial for carbon sequestration potential of biochar. However, long-term studies are recommended to fully understand the mechanisms that determine response of soil biota to biochar addition.

Shutdown for just six days enables land plants to entirely fix CO₂ excess of +4 Gt C per yr. Rebuilding soil organic carbon (SOC) in worm-worked humus is the only practical carbon capture and storage (CCS) capable of freely offsetting annual anthropogenic emissions. A case is made to redirect all available resources towards proven, earthworm-based, organic husbandry. Priority is to safely combat mounting global threats due to irreversible species extinction, perilous climate change and deteriorating human wellbeing (mental/physical health). All three interlinked risks are underpinned by a relentless, yet largely ignored, critical loss of precious topsoil. A first step to topsoil recovery is vermi-composting all vegetable and animal ‘wastes’ for return to the field.

The long-term use of fertilizers and pesticides in conventional cultivation has resulted in a decrease in soil productivity and vegetable yields in greenhouses. However, only a limited number of studies have explored the impacts of organic cultivation on greenhouse soil. Specifically, there is a scarcity of research examining the alterations in soil aggregate mediated organic carbon and microbial communities, which are known to enhance soil productivity. This study investigated the properties of soil aggregates, including the levels of organic carbon fractions, microbial community, and enzyme activity with the three aggregate classes microaggregates (<0.25 mm), small macroaggregates (2-0.25 mm) and large macroaggregates (>2 mm). These investigations were conducted under three different cultivation methods in a greenhouse: conventional cultivation (CC), integrated cultivation (IC), and organic cultivation (OC) in greenhouse. The results showed that (1) OC and IC promoted the formation of small macro-aggregates and enhanced aggregate stability compared to CC, (2) SOC in the three size fractions of OC increased by 98.99%-92.06% compared to CC; EOC increased by 98.47%-117.59%; POC increased by 138.59%-208.70%; MBC increased by 104.71%-230.61%; DOC increased by 21.93%-40.90%, respectively; (3) Organic cultivation significantly increased enzyme activity in all three particle size aggregates and increased the relative abundance of bacteria in micro-aggregates as well as the relative abundance of fungi in small macro-aggregates. Structural equation model (SEM) analysis revealed that organic farming practices fostered the development of smaller macro-aggregates, elevated microbial and enzyme activities within soil aggregates, and facilitated the conversion of soil nutrients and carbon sequestration. consequently, this led to an increase in soil organic carbon content and improved vegetable yield in greenhouse environments. In conclusion, the soil carbon content and vegetable yield are enhanced through long-term organic cultivation in greenhouses, primarily by increasing the proportion of small macro-aggregates.

Organic-rich shale deposits of the Paleocene-Eocene Palana Formation in western Rajasthan, India were systematically analyzed based on the elemental composition and organic geochemistry combined with microscopic examinations to evaluate the sedimentary paleoenvironmental conations and volcanic activity and their impact on the high organic carbon accumulation. The Palana shales are categorized by high OM and sulfur contents with total values up to 36.23 wt. % and 2.24 wt. %, respectively, suggesting marine setting and anoxic environmental conditions during the Paleocene-Eocene period. The richness of phytoplankton algae (i.e., telalginite and lamalginite) together with redox-sensitive trace elements further suggests anoxic environmental conditions. The significant low oxygen conditions may contributes to enhance preservation of organic matter during deposition. The mineralogical and inorganic geochemical indicators demonstrate that the Palana organic-rich shale facies was accumulated in warm and humid climate and low salinity stratification conditions of the water columns, thereby contributing to high bioproductivity of the phytoplankton algae blooms within the photic zone. The presence of the high concentrations of Fe-rich silica minerals such as olivine in most of the Palana organic-rich shales facility volcanic origin and supports hydrothermal activities during the Paleocene-Eocene period. These volcanic activities in this case are considered influx of large masses of nutrients into the photic zone due to the ash accumulation. Therefore, high bio-productivity associated with effective OM preservation contributed to the organic carbon accumulation in the Palana Formation during the Paleocene-Eocene.

In recent years, organic agriculture has gained more popularity, yet its approach to food production and its potential impact on consumers’ health and various environmental aspects remain to be fully discovered. The goal of organic farming practices is to maintain soil health, sustain ecological systems, maintain fairness in its relationship with the environment and protect the environment in its entirety. Various health benefits have been associated with higher consumption of organic foods. This review identified some of these health benefits including a reduction in obesity and body mass index (BMI), improvements in blood nutrient composition as well as a reduction in maternal obesity and pregnancy-associated preeclampsia risk. Furthermore, organic food consumption can reduce the development of non-Hodgkin lymphoma and colorectal cancers. Upon reviewing existing literature regarding the nutritional value of organic foods, it was found that organic food contained higher levels of iron, magnesium, and vitamin C. However, the evidence available to draw definitive generalizations remains limited. In this review, we provided essential insights to support sustainable organic farming and highlighted the potential of organic food consumption that could play a pivotal role in positively impacting human health.

Today, more disciplines are intercepting each other, giving rise to “cross-disciplinary” research. Technological advancements in material science and device structure and production have paved the way towards development of new classes of multi-purpose sensory devices. Organic phototransistors (OPTs) are photo-activated sensors based on organic field-effect transistors that convert incident light signals into electrical signals. The organic semiconductor (OSC) layer and three-electrode structure of an OPT offer great advantages for light detection compared to conventional photodetectors and photodiodes, due to their signal amplification and noise reduction characteristics. Solution processing of the active layer enables mass production of OPT devices at significantly reduced cost. The chemical structure of OSCs can be modified accordingly to fulfil detection at various wavelengths for different purposes. Organic phototransistors have attracted substantial interest in a variety of fields, namely biomedical, medical diagnostics, healthcare, energy, security, and environmental monitoring. Lightweight and mechanically flexible and wearable OPTs are suitable alternatives not only at clinical levels but also for point-of-care and home-assisted usage. In this review, we aim to explain different types, working mechanism and figures of merit of organic phototransistors and highlight the recent advances from the literature on development and implementation of OPTs for a broad range of research and real-life applications.

Metals are particularly sensitive to some pollutant gases. Many museum showcases and store rooms present atmospheres that can corrode cultural heritage artefacts containing metals. Whilst numerous strategies have been reported to mitigate such situations, avoiding them is preferable. Several approaches to testing materials used in construction, fitting out or dressing are used. The relative merits and drawbacks will be discussed. Several parameters of the most widely used, the accelerated corrosion ‘Oddy’ test have been investigated. The influence of abrasive on subsequent corrosion of lead and copper coupons have been assessed. Quantification methods for tested coupons are reviewed. The influence of test duration and temperature were assessed through comparison with real life, long term experience of materials behaviour. Direct contact tests with the material tested touching the test material has been investigated. Several materials present in artefacts are known to potentially cause corrosion when enclosed with metals in other artefacts. A number of situations have been investigated with pollution and RH and some corrosion rate measurements. Ways to isolate artefacts or mitigate are explored and a decision support model has been developed.

This research was conducted to analyze the content of Fe, Cu, Cd, Cr, and Pb in several species of fish taken from three lakes that is closely to disposal of industrial waste in Indonesia. The fish samples were taken from three lakes, namely, Muara Angke, Weda, and Morowali. The samples from Morowali were analyzed in April 2019, those from Weda from November to December 2019, and those from Muara Angke in June 2018. All the samples were then analyzed at the chemistry laboratory of the Department of Chemistry, Faculty of Mathematics and Natural Science, University of Indonesia, and the Integrated Laboratory of IPB. The results showed that all types of fish from Morowali and Weda were no longer safe to consume because they contained Fe, Cu, Cd, and Cr exceeding the threshold of metal contamination. Meanwhile, all types of fish from Muara Angke, except for ayam-ayam, are still safe for consumption. The results of this study can be a source of information regarding metal content in fish and fish feed for safe consumption. Several studies have been done to determine the metal pollutants contained by fish. Given the high consumption rate of fish and the hazards of heavy metals on humans’ health, such research must be furthered

Gasca D herbal formulation is an antidiabetic medicine for the management of diabetes mellitus produced exclusively from natural ingredients. The level of some essential elements (Copper, chromium, Cobalt, Iron, Manganese, Nickel and zinc) and toxic (Cadmium, Arsenic, Mercury, and Lead) heavy metals were determined using microwave plasma-atomic emission spectrometry (MP-AES). The aim of this study is to evaluate the levels of essential and toxic heavy metals and also identify bioactive compounds present in Gasca D herbal formulation. The result shows no traces of Lead, Mercury, Zinc, Arsenic and Zinc, Iron was found to have highest concentration 67.16 + 7.5 µg/g and Cadmium lowest concentration 0.4 + 0.03µg/g. GC-MS analysis of Gasca D herbal formulation revealed the presence of 14 biologically active compounds which include N-Formyl-beta-alanine, Paromomycin, 3,4-Altrosan, Benzamide, 1,3,4-Thiadiazol-2-amine, Carbamodithioic acid, Carbonic acid, alpha-D-Glucopyranoside, Ethyl isocyanide, 2-Propanesulfinic acid, Propanamide, 2-Butenenitrile, Dicyclopropyl carbinol, Isoxazolidine, 1,5-Hexadiene 10-Azido-1-decanethiol. Conclusion: The result indicates that the mean levels of toxic metals in Gasca D herbal formulation were below WHO permissible levels. Gasca D herbal formulation also contains various bioactive compounds that can have various medicinal application which can be used for the treatment of various diseases.

Based upon Maxwell's equations, it has long been established that oscillating electromagnetic (EM) fields incident upon a metal surface decay exponentially inside the conductor, leading to a virtual EM vacuum at sufficient depths. Magnetic resonance imaging (MRI) utilizes radiofrequency (r.f.) EM fields to produce images. Here we present the first visualization of a virtual EM vacuum inside a bulk metal strip by MRI, amongst several novel findings. We uncover unexpected MRI intensity patterns arising from two orthogonal pairs of faces of a metal strip, and derive formulae for their intensity ratios, revealing differing effective elemental volumes (voxels) underneath these faces. Further, we furnish chemical shift imaging (CSI) results that discriminate different faces (surfaces) of a metal block according to their distinct nuclear magnetic resonance (NMR) chemical shifts, which holds much promise for monitoring surface chemical reactions noninvasively. Bulk metals are ubiquitous, and MRI is a premier noninvasive diagnostic tool. Combining the two, the emerging field of bulk metal MRI can be expected to grow in importance. The fundamental nature of results presented here may impact bulk metal MRI and CSI across many fields.

A useful and increasingly common additive manufacturing (AM) process is the selective laser melting (SLM) or direct metal laser sintering (DMLS) process. SLM/DMLS can produce full-density metal parts from difficult materials, but it tends to suffer from severe residual stresses introduced during processing. This limits the usefulness and applicability of the process, particularly in the fabrication of parts with delicate overhanging and protruding features. The purpose of this study was to examine the current insight and progress made toward understanding and eliminating the problem in overhanging and protruding structures. To accomplish this, a survey of literature was undertaken, focusing on process modeling (general, heat transfer, stress and distortion, and material models), direct process control (input and environmental control, hardware-in-the-loop monitoring, parameter optimization, and post-processing), experiment development (methods for evaluation, optical and mechanical process monitoring, imaging, and design-of-experiments), support structure optimization, and overhang feature design; approximately 140 published works were examined. The major findings of this study were that a small minority of the literature on SLM/DMLS deals explicitly with the overhanging stress problem, but some fundamental work has been done on the problem. Implications, needs, and potential future research directions are discussed in-depth in light of the present review.

: This study was conducted to evaluate the behavior of nitrate, moisture and organic matter in a soil with low agronomic input. The test was conducted on silty-sandy soil, a temporal variability of the variables in the different seasons was observed in the three theses. The theses were observed in parallel twice a week. Nitrates showed an increase during the summer-autumn season with higher values ​​in the thesis containing organic matter, “bare soil” followed by the thesis “fallow” and finally by the “cultivated” (see below in experimental set up). The humidity was higher in the “bare soil” thesis followed by “fallow” and “cultivated” one during the summer, in winter the “cultivated” showed the lowest humidity compared to the other two theses. The organic matter does not show great variability in the seasons but is higher in the “fallow” thesis followed by “bare soil” and “cultivated” one. The Montecarlo test informed us that organic matter and humidity were autocorrelated within 5-7.5 m of distance (10-15 lag) while nitrates even if they seemed to be not autocorrelated with each other and have a cyclical pattern.

Dissolved organic matter (DOM) derived from organic fertilizers may increase soil phosphorus (P) availability. However, the frequently observed correlation between soil P availability and dissolved organic carbon (DOC) content has led to an excessive focus on DOC content at the expense of DOM properties. The present study investigated the influence of DOM characteristics on soil P availability by using a 6-year field experiment and microcosms of P sorption in paddy soil. Our results showed that partial replacement of chemical P fertilizer with manure or crop straw increased P fertilizer-use efficiency, even when decreasing chemical P input by 34 %, compared to normal chemical fertilization. The microcosm experiment demonstrated that DOM properties, rather than total DOC content, determine soil P sorption capacity, despite the significant correlation between DOC content and P availability observed in the field experiment. Manure-DOM exerted stronger inhibitory effects on P sorption than straw-DOM, and high molecular weight (HMW)-fractionated DOM exerted stronger inhibitory effects on P sorption than low-molecular-weight-fractionated DOM by 16-20%. The mechanism was rooted in the HMW DOM with unique characteristics (e.g., strong aromaticity, hydrophobicity, abundant humic-like components, carboxyl groups, and benzene ring structures) competing for soil P sorption sites (e.g., reduction in specific surface area and micropore volume), decreasing the soil surface charge (e.g., zeta potential), and thereby suppressing P sorption in paddy soil. Our study points out a promising avenue for regulating organic matter properties with organic fertilization to improve P use efficiency in agricultural soils.

Chemical versatility of organic semiconductors provides nearly unlimited opportunities for tuning their electronic properties. However, despite decades of research, relationship between molecular structure, molecular packing and charge mobility in these materials remains poorly understood. This reduces the search for high-mobility organic semiconductors to the inefficient trial-and-error approach. For clarifying the abovementioned relationship, investigations of the effect of small changes in the chemical structure on OSs properties are particularly important. In this study, we address computationally the impact of substitution of C-H atom pairs by nitrogen atoms (N-substitution) on molecular properties, molecular packing and charge mobility of crystalline oligoacenes. Besides of decreasing frontier molecular orbital levels, N-substitution dramatically alters molecular electrostatic potential yielding pronounced electron-rich and electron-deficient areas. These changes in the molecular electrostatic potential strengthen face-to-face and edge-to-edge interactions in the corresponding crystals and result in the crossover from the herringbone packing motif to π-stacking. When the electron-rich and electron-deficient areas are large, sharply defined and, probably, have certain symmetry, charge mobility increases up to 3-4 cm2V-1s-1. The results obtained highlight the potential of azaacenes for application in organic electronic devices and are expected to facilitate rational design of organic semiconductors for steady improvement of organic electronics.

Soil organic carbon (SOC) mineralization is closely related to carbon source or sink of terrestrial ecosystem. Understanding soil organic carbon (SOC) mineralization under plum plantation is essential for improving our understanding of SOC responses to land-use change in karst rocky desertification ecosystem. In this study, 2-y, 5-y and 20-y plum plantations and adjacent woodland were sampled and a 90-day incubation experiment was conducted to investigate the effect of plum plantation with different years on SOC mineralization in subtropical China. Results showed that: (1) there was no significant difference in SOC content between different planting years, but there were significant differences in accumulative SOC mineralization (C_t) and potential SOC mineralization (C₀); (2) the dynamics of the SOC mineralization was a good fit to a first-order kinetic model. Both C₀ and C_t in calcareous soil of this study was several to ten folds lower than that in other soils, indicating that SOC in karst region has higher stability. (3) Correlation analysis revealed that both C_t and C₀ was significantly correlated with soil calcium (Ca) and C/N, indicating the important role of Ca and C/N in SOC mineralization in karst rocky desertification area.

Soil amendments with composted organic materials are recommended to increase soil organic matter (SOM), promote soil fertility, and the Circular Economy. Growing areas of hedged olive groves in southern Iberia peninsula generate huge amounts of olive leaves whose potential as soil organic amendment is not fully studied. An experimental field trial in a hedged olive grove (cv. “Cobrançosa”) was set up near Portalegre, Portugal, to test a compost of olive leaves plus sheep manure (2:1) applied in the row, at soil surface. Three nominal rates (0 or control, 2.5 and 5.0 kg m-2) were used, in a complete randomized block setup (3 treatments, 3 replicas, 9 plots) and soil chemical properties of layers 0-5, 5-15, and 15-30 cm deep were annually monitored. Results (mainly in layer 0-5 cm) showed increases in total N, carbon of the particulate organic matter (POM-C), permanganate oxidizable carbon (POX-C), extractable phosphorus, and zinc, after one year, and increases in soil organic carbon (SOC), C-stock, pHKCl, extractable phosphorus, and zinc, after two years. POX-C was the most sensitive SOM-related indicator, showing increases up to 30 cm deep after one year. This compost improved soil fertility, but should be monitored over longer periods of time, namely for SOC and extractable zinc content.

The bimetallic (Ta/(Ti, V, Co, Nb) mesoporous MCM-41 nanoparticles were obtained by direct synthesis and hydrothermal treatment. The obtained mesoporous materials were characterized by XRD, XRF, N2 adsorption/desorption, SEM, TEM, XPS, Raman, UV-Vis, PL spectroscopy. A more significant effect was observed on mesoporous structure, typi-cally for MCM-41, and optic properties if the second metal (Ti, Co) does not belong to the same Vb group with Ta as V, Nb. The obtained new nanoparticles were used as catalysts for oxidation with H2O2 of olefinic compounds (1,4 cyclohexadiene, cyclohexene, styrene) and photodegradation of organic pollutants (phenol, methyl orange) from water. The re-sults showed improving of activity and selectivity in oxidation reactions by addition of the second metal to Ta-MCM-41 catalyst. The slow addition of H2O2 was also be benefit for the selectivity in epoxide products and stability of the catalysts. The band gap energy values decrease in the presence of the second metal and the band edge diagram evidenced posi-tive potential for all the conduction band of the bimetallic samples except TaTi-MCM-41. The higher photocatalytic degradation was obtained for samples with TaTi and TaV.

Composite polymolecular separation membranes were prepared by combining multi-branched ZIF-L with high porosity electrospinning nanofibers PI. Meanwhile, PDA and PEI were introduced into the membrane in order to improve its adhesion. The new membrane is so called “PI@PDA@PEI/ZIF-L-4” composite membrane; compared with PI@PDA@PEI/ZIF-8 composite membrane, the new membrane’s filtration rates for heavy metal ions such as Cd2+, Cr3+ and Pb2+ were increased by 7.0%, 6.6% and 9.3%, respectively. Furthermore, the new membrane has a permeability up to 1,140.0 L·m−2·h−1·bar−1, and were presenting a very stable performances after four repeated uses. The separation mechanism of PI@PDA@PEI/ZIF-L composite membranes was further analyzed in order to provide a base support for producing separation membranes with high barrier rate and high flux.

The transferability of structure-property relationships for laser-pretreated metal adhesive joints to laser-pretreated metal – carbon fiber reinforced plastic (CFRP) bonds is investigated. Single-lap shear tests were performed on hybrid AW 6082-T6 – CFRP specimens pretreated with the same pulsed laser surface parameter sets on the metal surface as previously tested AW 6082-T6 – E320 metal adhesive joints. The fracture surfaces were characterized to determine the type of failure and elucidate differences and commonalities in the link between surface structures and single-lap shear strengths. Digital image analyses of the hybrid specimens fractured surfaces were used to quantify remaining CFRP fragments on the metallic joint side. The results indicate that high surface enlargements and the presence of undercut structures leads to single-lap shear strengths exceeding 40 MPa and 35 MPa for unaged and aged hybrid specimens respectively. While for the metal-polymer joints the trend from high strength to weakly bonded specimens was largely continuous with the degree of surface structuring, hybrid metal – CFRP joints exhibit a drastic drop in joint performance after aging if the laser-generated surface structures are less pronounced with low surface enlargements and crater depths. Surface features and hydrothermal aging determine whether the specimens fail cohesively or adhesively.

Tillage has been reported to induce seasonal changes of organic carbon (Сmicro) and nitrogen (Nmicro) in biomass of microorganisms. Soil microorganisms execute such ecosystem functions as: it is an immediate sink of labile biophil elements; it is an agent of a conversion, catalysis and synthesis of humus substances; it transforms soil contaminants into non-hazardous wastes; it participates in soil aggregation and pedogenesis as a whole. However, the seasonal turnover of microorganisms on arable lands in temperate ecosystems has not been investigated on a relevant level. Hence, we aimed to study the dynamics of such soil microbial biomass patterns as: Сmicro, Nmicro, microbial index (MI = (Сmicro/CTOC)·100, %) and CO2-C emission on the background of 9 years of tillage and 22 years of abandoned (Ab) and fallow (F) usage. Our study was conducted on a long-term experimental site on a Mollisol in the northeast China. The maximum Сmicro and Nmicro content was found: at the beginning of the growing season – in 0-10-; in mid-July – in 20-40 cm layers, while the minimum – in August-October. The Сmicro content ranged from 577.79- and 381.79 mg-1 kg-1 under Ab in spring to 229.53- and 272.86 mg-1 kg-1 in autumn under CT (conventional tillage) and F in 0-10- and 10-20 cm layers, respectively. The amplitude of Nmicro content changes was several times lower comparatively to Сmicro. The smallest quartile range (IQR0.25-0.75) of such changes was under: no-till (NT) and Ab in 0-10-, NT and F – in 10-20- and CT - in 20-40 cm layers. The widest Сmicro : Nmicro ratio was found at F and CT – in 0-20- and CT and rotational tillage (Rot) – in 20-40 cm layers. MI dynamics resembled the trends of Сmicro and Nmicro and changed from 0.72  0.168- tо 2.00  0,030 %. The highest part of Сmicro in CTOC was at Ab (1.82  1.85 %) and NT (1.66  1.52 %) – in 0-10-; Ab (1.23  1.27 %) and NT (1.29  1.32 %) – in 10-20- and – Ab (1.19  1.09 %) and F (1.11  1.077 %) – in 20-40 cm layers, correspondingly. The Pearson’s correlation coefficient between Сmicro and CTOC increased from the upper 0-10- to the lower 20-40 cm layer, it was "strong" and "high" between Сmicro and CTOC. Different use of Mollisol affected the amplitude of Сmicro and Nmicro seasonal changes, but it didn’t change their trend. Our results suggest the key role of Ab and NT technologies in Сmicro accumulation in total organic carbon (TOC).

Peptides, both natural and synthetic, are well suited for a wide range of purposes and offer versa-tile applications in different fields such as biocatalysts, injectable hydrogels, tumor treatment, and drug delivery. The rising prominence of therapeutic peptides encompasses anticancer, antiviral, antimicrobial, and anti-neurodegenerative properties. The metals Na, K, Mg, Ca, Fe, Mn, Co, Cu, Zn, and Mo are ten of the twenty elements that are considered essential for life. Crucial for under-standing the biological role of metals is the exploration of metal-bound proteins and peptides. Aside from essential metals, there are other, non-essential metals that also interact biologically, exhibiting either therapeutic or toxic effects. Irregularities in metal binding contribute to diseases like Alzheimer’s, neurodegenerative disorders, Wilson's, and Menkes disease. Certain metal com-plexes have potential applications as radiopharmaceuticals. The examination of these complexes was done by preforming UV-Vis, IR, EPR, NMR spectroscopy, and X-ray analysis.

We studied surface enhanced Raman spectra of amino acids D-alanine and DL-serine and their mixture on silver nanoisland films (SNF), immersed in phosphate buffer saline solution at millimolar amino acid concentrations. It is shown that the spectra from the amino acid solutions differ from the reference spectra for microcrystallites due to electrostatic orientation of amino acid zwitterions by the metal nanoisland film. Moreover, non-additive peaks are observed in the spectrum of the mixture of amino acids adsorbed on SNF, which means that intermolecular interactions between adsorbed amino acids are very significant. The results indicate the need for a thorough analysis of the Raman spectra from amino acid solutions in the presence of a nanostructured metal surface, and may also be of interest for studying molecular properties and intermolecular interactions.

Dendrite growth and parasitic reactions with liquid electrolyte are the two key factors that restrict the practical application of the lithium metal anode. Herein, a bis(benzene sulfonyl)imide based single-ion polymer artificial layer for lithium metal anode is successfully constructed, which is prepared via blending the as-prepared copolymer of lithiated 4, 4’-dicarboxyl bis(benzene sulfonyl)imide and 4,4’-diaminodiphenyl ether on the surface of lithium foil. This single-ion polymer artificial layer enables compact structure with unique continuous aggregated Li+ clusters, thus reducing the direct contact between lithium metal and electrolyte, and ensuring Li+ transport fast and homogeneous simultaneously. Based on which, the coulombic efficiency of the Li|Cu half-cell is effectively improved, and the cycle stability of the Li|Li symmetric cell can be prolonged from 160 h to 240 h. Surficial morphology and elemental valence analysis confirm that the bis(benzene sulfonyl)imide based single-ion polymer artificial layer effectively facilitates the Li+ uniform deposition and suppresses parasitic reactions between lithium metal anode and liquid electrolyte in the LFP|Li full-cell. This strategy provides a new perspective to achieve steady lithium metal anode, which can be a promising candidate in practical application.

The presence of organic dyes in aqueous environments is of extreme hazardousness against life due to the toxicity of these compounds. Thus, its removal from these various aquatic media is of the utmost importance and several technologies are constantly proven to match this goal. Among these technologies, various types of degradation and adsorption are the most widely used, and of the various types of materials used within these technologies, nanomaterials are constantly developed and investigated, probably due to the various properties that these nanomaterials presented. This work reviewed recent developments (2023 year) about the use of these nanomaterials on the treatment of solutions contaminated with these toxic organic dyes.

The aim of this paper was to determine the soil phosphorus release risk from drained and re-wetted peatlands under different landcovers. The study was carried out at 10 soil profiles (organic soils, frequently with mursh in the topsoil, developed from low peat with various degrees of decomposition, on mineral subsoil or gyttja) located south-west of Lake Kośno nature reserve in northern-central Europe (north-eastern Poland). The soil samples were collected from the depths of 0-30 cm, 50-80 cm and 100-130 cm during spring, summer and autumn (in April, July, and October). In the laboratory, the following soil properties were determined: ash content, soil reaction, content of total organic carbon, total nitrogen, total and plant-available phosphorus. Gyttja formations and hemic peats had the highest total P content (6.77 g∙kg-1 and 2.29 g∙kg-1, respectively). Murshes contained twice less P (1.18 g∙kg-1). In spring, more plant-available phosphorus (AP sp) was released in murshes (0.29 g∙kg-1) than in peats (0.07-0.14 g∙kg-1). In the summer, higher amounts of plant-available P were stated in fiber peats (0.37 g∙kg-1) than in murshes (0.26 g∙kg-1), whereas in autumn, the amounts of P in murshes (0.22 g∙kg-1) and peats (0.21-0.23 g∙kg-1) did not vary. Generally, average contents of AP were the highest in murshes (0.26 g∙kg-1) and fiber peats (0.25 g∙kg-1), and the lowest in sapric peats (0.15 g∙kg-1). The release of phosphorus from organic compounds or binding of P by organic matter (immobilization) depends on the C:P ratio in plant residues and soil. If it is wide (>300), P is bound, if it is narrower (150–200), P is released. In the tested soil formations, the C:P ratio was frequently above 300. Only in some murshes and gyttjas the C:P ratio was below 150, which may indicate a risk of phosphorus release to groundwaters.

In the era of disruption, to achieve food sustainability and the SDGs, Indonesia is faced with changes in the values, attitudes, and behavior of the community to be adaptive to environmental and technological changes. This study aims to analyze the factors that influence social transformation in peri-urban communities and their impact on food sustainability and the achievement of SDGs. The research method is a qualitative approach, triangulated by conducting in-depth interviews, field observations, and focus group discussion (FGD) in two districts. The results showed that factors influencing social transformation in peri-urban communities include: strengthening public awareness of the importance of food sustainability, access to information and technology, collaborative synergetic of government, companies, academics, and community participation in decision-making on empowerment programs. This social transformation leads to increased food production and poverty reduction. Private facilitators through CSR programs play a role in achieving food sustainability and achieving several SDG indicators related to poverty. The occurrence of collaborative synergetic between community participation, extension workers, village government, media utilization, academics, and companies contributes significantly to transforming the values, attitudes, and behavior of people managing community resources.

This study investigated the factors that influence consumer acceptance of fungus-resistant grape varieties (FRGV) in Germany. The qualitative research methodology involved conducting semi-structured interviews including sensory evaluation test with focus groups consisting of 48 consumers, and the data were evaluated using content analysis. The findings revealed that the attractiveness of a grape variety is determined by four distinct attributes. Furthermore, FRGV can be made more attractive to consumers by using denominations based on established grape varieties or by using and associating them with their sensory patterns. The sensory acceptance of FRGV varies significantly across consumer segments and vinification methods. Providing relevant information about the benefits of resistant grape varieties has a positive impact on consumer acceptance, and the level of interest and relevance varies by the target group. The study suggests that it is possible to enhance consumer acceptance by offering attractive grape varieties, targeting group-specific sensory profiles and engaging in storytelling campaigns that educate consumers about the advantages of resistant grapes.

Interest in organic foods is increasing at a moment when humanity is facing a range of health challenges including the concern that some conventionally produced foods may pose possible adverse effects on human and livestock health. With the increasing human population, intensive production is increasingly trending towards high-input systems that aim to close yield gaps, increase crop yields, and develop new crop varieties with higher yield potential and tolerance to biotic and abiotic stresses, all within the context of incorporating specific traits to satisfy consumer demand. Potato (Solanum tuberosum L.) is one of the most consumed foods under different cultural diets, however its production faces some challenges related to soilborne diseases, marketable yield and quality, sugars and dry matter content of the produced tubers, tuber content in terms of nitrate, minerals, vitamins, bioactive compounds and antioxidants, and consumer appreciation regarding the sensory characteristics of tubers and processed products. Different studies have been investigating some of these challenges, with sometimes straightforward and sometimes connflicting results. This variability in research results indicates the general non-transferability of the results from one location to another under the same management practices in addition to differences in plant material. This review compares some characteristics of raw or boiled potato and processed products from potato tubers grown organically and conventionally. Ideally, such information may be of benefit in decision making by consumers in their dietary choices, by potato growers in their selection of crop management practices, and by scientists looking at potential areas for future research on potatoes.

We develop an optimized force-field for poly(3-hexylthiophene) (P3HT) and demonstrate its utility for predicting thermodynamic self-assembly. In particular, we consider short oligomer chains, model electrostatics and solvent implicitly, and coarsely model solvent evaporation. We quantify the performance of our model to determine what the optimal system sizes are for exploring self-assembly at combinations of state variables. We perform molecular dynamics simulations to predict the self-assembly of P3HT at ~350 combinations of temperature and solvent quality. Our structural calculations predict that the highest degrees of order are obtained with good solvents just below the melting temperature. We find our model produces the most accurate structural predictions to date, as measured by agreement with grazing incident X-ray scattering experiments.

Honey is a sweet substance extensively consumed in the world for its nutritional and healthy properties. However, residues of pesticides and environmental contaminants can compromise its quality. For this reason, the physicochemical parameters, and the organic contamination of monofloral and multifloral honeys from three regions of Algeria (Tiaret, Laghouat and Tindouf) were monitored to evaluate the quality of honey and the safety for consumers. In general, the results obtained from the physicochemical analyses were in line with the EU standards. In terms of contamination, pesticides authorised and used in Algerian agriculture (matalaxyl-M and cyromazine), as well as banned pesticide (carbaryl), were found in almost all the samples. However, only the concentration of cyromazine was higher than the relative EU maximum residue levels. PCB 180, PCB 189, anthracene, fluorene and phenanthrene were mainly detected. All the honeys show traces of DiBP, DBP, DEHP and DEHT, but no traces of bisphenols were found. Moreover, the dietary exposure assessment shows that a small amount of Algerian honey can be safely consumed. Overall, data from this study should motivate the Algerian government to enhance their monitoring activities in beekeeping and to find solutions for implementing more sustainable agricultural practices harmonizing with the international legislation.

We investigated and quantified soil organic carbon (SOC) stock at the mangrove forest (Magyi, That Bot Khan and Wette) of Shwe Thaung Yan coastal region in Myanmar and estimated the SOC stock changes in Magyi mangrove forest over six years using repeated field measurements. The study sites were characterized by different mangrove vegetation, soil types, and sediment deposition from different water sources. Results showed that the mangrove preservation and restoration efforts had a significant effect on soil C storage, with soil carbon stocks in 2021 (1954.43 ± 33.24 ton/ha) being 2.7 times higher than the estimated carbon stock in 2015 (732.26 ± 6.99 ton/ha). The results also revealed slight differences in SOC between Magyi and the Tha-Bot-Khan and Wette areas, as the mangrove plants in the latter areas have an additional source of nutrients from Pho-Thoung-Gyi, a deep-sea bay near the forest. Our research findings are beneficial in understanding the role of Myanmar’s mangrove ecosystems in carbon sequestration and climate change mitigation efforts.

Lead-free ferroelectric perovskite N-methyl-N'-diazabicyclo[2.2.2]octonium)–ammonium triio-dide, MDABCO-NH₄I₃, nanocrystals are embedded in three different polymer fibers fabricated by the electrospinning technique. The nanofibers, which are very flexible and have a high Young modulus, behave as active piezoelectric energy harvesting sources that produce a piezoelectric voltage coefficient up to geff = 3.6 VmN-1 and show a blue intense luminescence band at 325 nm. In this work, the pyroelectric coefficient is reported for the MDABCO-NH₄I₃ perovskite inserted in electrospun fibers. At the ferroelectric-paraelectric phase transition, the embedded nanocrystals display a pyroelectric coefficient as high as 194×10-6 Cm-2k-1, within the same order of magnitude as that reported for the state-of-the-art bulk ferroelectric triglycine sulfate (TGS). The perovskite nanocrystals embedded into the polymer fibers remain stable, and no degradation is caused by oxidation.

High-quality and large-size single crystals of lead-free Na0.5Bi0.5TiO3 were grown using the Czo-chralski technique. The crystals had pure perovskite structure with rhombohedral symmetry and were translucent in the visible and near infrared spectral ranges recorded in the interval 350-1050 nm. The energy gaps determined from the X-ray photoelectron spectroscopy (XPS) and optical measurements were approximately 2.92 eV. The current-voltage characteristics, depolarization current, dc (σdc) and ac (σac) electrical conductivity, and Seebeck coefficient of the crystals were investigated. The frequency/temperature-dependent electrical properties were also measured and analyzed through complex impedance spectroscopy. An overlapping reversible insulator-metal transition (resistive switching) on nanoscales, caused by the electric field, was detected. This was the first time that most of these investigations were performed for this material. The following conductivity mechanisms of NBT single crystals were identified: (i) quasi-free electron and hole conduction and hopping-charges mechanism at low temperatures, (ii) small polaron conductivity in the middle temperature range, and (iii) a significant contribution of the oxygen vacancies to conductivity in the high temperature range. The activation energy values determined from the conductivity data, the imaginary part of the electric impedance and the modulus indicate that the relaxation process in the high-temperature range is attributable to both single and double ionized oxygen vacancies, in combination with the hopping of electrons between Ti4+ and Ti3+. P-type electrical conductivity was also found. These discoveries create new possibilities of reducing the electrical conductivity of NBT and improving the process of effectively poling this material. The density of the electronic states was investigated using an ab initio method. The energy gap cal-culated for NBT (R3c) was 2.8 eV, and is well comparable to those determined from XPS and optical measurements. Our results indicate the possibility of tuning material properties by inten-tionally creating non-stoichiometry/structural defects (oxygen vacancies, cation excess and cation deficiency).

With this article, impact of effluent mixed water with the quality of the Mansagar Lake has been established by evaluating the physico-chemical parameters and the heavy-metal contents experimentally. The process of calculating water quality and the metal pollution quality indices is also explained in brief with respect to selected sample locations and varied environmental conditions (Pre- and Post-Monsoon season). Distribution trends of Pearson‘s correlation factor have also been discussed to establish their relation among the physico-chemical parameters and the heavy-metal contents for varied environmental conditions. In the end, detailed discussion on observations made during this study and useful recommendations are also elaborated in details. With this article, we intend to present a document for better understanding of the water quality of this lake in view of futuristic management strategies to be adopted to maintain it heritage values.

The efficiency of cold sheet and strip rolling of steels and non-ferrous metals in the main depends on the quality of the technological lubricant and its cost. In this regard, it is important to develop new compositions of effective metal-working coolants (MWC) having low cost and providing the maximum reduction in the friction coefficient. We developed and tested the new compositions of the MWC on basis of chicken fat, and mono- and diglycerides and their esters of boric acid synthesized from the wastes of sunflower oil production. The MWC were tested in DSEA on laboratory rolling mill 100x100 with a roll diameter of 260 mm during steel 08Kp rolling. The efficiency of the coolants was determined by the factor of metal stretch forming λ and the coefficient of friction μ in the deformation zone which was found by forward slip method. We found the metal-working coolant with 100 % concentration of boric acid esters of mono- and diglycerides is the most effective in steel rolling. Thus the new MWC on basis of boric acid esters of mono- and diglycerides synthesized from the wastes of sunflower oil production can be recommended for use in rolling of structural steels on account of availability, high efficiency, and a low cost.

Hydrogen gas (H2) has attracted attention as a next-generation clean energy source. Its efficient and safe preparation and utilization are crucial in both industry and organic chemistry. In this study, a Pt/CB-catalyzed MW-mediated continuous-flow hydrogenation reaction was developed using methylcyclohexane (MCH) as the reducing agent (hydrogen carrier). Alkynes, alkenes, nitro groups, benzyl esters, and aromatic chlorides were chemoselectively hydrogenated using Pt/CB under MW-assisted continuous-flow conditions. This methodology represents a safe and energy-efficient hydrogenation process, as it eliminates the need for an external hydrogen gas supply or heating jackets as a heat medium. Further application of MW-mediated continuous-flow hydrogenation reactions is a viable method for the efficient generation and utilization of sustainable energy.

This study investigates the petroleum potential of the Middle Jurassic Khatatba Formation (Fm) in the Matruh Basin, northwestern Egypt. This formation shows in situ dual source and reservoir characteristics, where alternations of fine and coarse clastics were deposited during semi-arid and semi-humid conditions due to climate changes and Tethyan sea level fluctuations. The organic-rich shales and argillaceous siltstones are fair to very good/excellent (TOCm wt%: 0.91–3.07) source rocks. They are rich in late mature to early postmature mostly gas-prone organic facies C, which sourced the juxtaposing intraformational coarse clastics of the Lower Safa Member with gas and condensates. The source rocks show poor to fair gas generation potential (S2: 0.38–1.96, mg HC/g rock). The middle part of the Lower Safa Member shows excellent organic richness (TOCm wt%: 5.39 and 22.90) of early postmature gas-prone carbonaceous material and coal deposits. These coaly shale layers exhibit fair to excellent wet gas and condensate generation potential (S2: 4.51–27.43, mg HC/g rock). Maturation of the source rocks was related to the Late Jurassic–Early Cretaceous Tethyan rifting. The onset of oil generation occurred in the Early Cretaceous (~ 116 Ma ago), while the onset of gas generation occurred in the Oligocene (~ 24 Ma ago). Shales of the Lower Cretaceous Alam El Bueib Fm are primary sealing rocks, while carbonates and shales of the Khatatba Fm are secondary sealing rocks. Trap types are structural, formed during the Late Jurassic and Early Cretaceous rifting of the Matruh Basin. Sandstones of the Upper Safa Member show upward increases in kaolinite and exhibit low-quality tight sandstone reservoirs. The Lower Safa Member sandstones show better gas reservoir quality with lower shale volumes. Operationally, the Lower Safa sandstone reservoirs in the Imhotep W-1X well are not suitable for gas production because they are ductile and show a high decline in production and pressure. Overall, the petroleum system of the Khatatba Fm shows mainly fair hydrocarbon potential in the study area.

Metal additive manufacturing (AM), commonly referred to as 3D printing with metals, is an innovative technology with significant potential to transform industries such as aerospace, automotive, and healthcare. Despite its promise, the field faces several challenges that impact both its technical feasibility and economic viability. This paper explores the primary technical challenges, including material properties and processing complexities, such as the need for precise control of thermal gradients and the mitigation of defects like porosity and residual stresses. Additionally, it addresses the economic barriers, including high initial equipment costs, the need for specialized knowledge, and the relatively slow build speeds compared to traditional manufacturing methods. By examining these challenges, this paper aims to provide a comprehensive overview of the current state of metal additive manufacturing and suggest potential pathways for overcoming these obstacles to facilitate wider adoption and technological advancement in the field.

Toxic metal wastewater is a challenge for exposed terrestrial, aquatic environments and the recyclability of the water, prompting inputs for the development of promising treatment methods. Consequently, the rGO/ZnONP nanocomposite was synthesized at room temperature for four hours and was tested for adsorption of cadmium and lead in wastewater. The optimized nanocomposite had the lowest band gap energy (2.69 eV) and functional group interactions were at 516, 1220, 1732, 3009, and 3460 cm-1. The nanocomposite showed saturation of ZnO nanoparticles on rGO with a weight percentage of zinc (60.02 %), oxygen (22.96 %), and carbon (16.58 %), and the micrograph showed slight agglomeration on the sheet surface. The nanocomposite’s D and G band intensities were almost the same constituting the ZnO presence on rGO from the raman spectrum. The adsorption equilibrium time for cadmium and lead was reached within 10 and 90 minutes with efficiencies of ~ 100 %. Sips and Freundlich were best fitting the cadmium and lead adsorption data (R2 ~ 1), therefore the adsorption was a multilayer coverage for lead and a mixture of heterogenous and homogenous coverage for cadmium adsorption. Both adsorptions were best fitted by the pseudo first order model, suggesting the multilayer coverage dominance. The adsorbent was reused for three and seven times for cadmium and lead. The nanocomposite showed selectivity towards lead (95 %) and cadmium (100 %) in the interfering wastewater matrix. Conclusively, the nanocomposite may be embedded within upcoming lab-scale treatment plants which could lead to further upscaling and serving as industrial wastewater treatment material.

Wastewater contaminated with antibiotics is a major environmental challenge. We developed here the green synthesis of bio-graphenes by using natural precursors (Xanthan, Chitosan, Boswellia, Tragacanth). The use of these precursors can act as templates to create 3D doped graphene structures with special morphology. Also, this method is a simple method for in-situ synthesis of doped graphenes. The elements present in the natural polymers (N) and other elements in the natural composition (P, S) are easily placed in the graphene structure and improve the catalytic activity due to the structural defects, surface charges, increased electron transfers, and the high absorption. In this mechanism, O2 dissolved in water absorbs onto the positive charged C in doped graphenes to create oxygenated radicals, which enables the degradation of antibiotic molecules. Light irradiation increases the amounts of radicals and rate of antibiotic removal. The results have shown that the hollow cubic Chitosan-derived graphene has shown the best performance due to the doping of N, S, and P. The Boswellia-derived grapheme shows the highest surface area, but lower catalytic performance, which indicates the more effective role of doping in the catalytic activity. The effect of oxygen and light were also studied to accelerate the degradation process.

: AlF3 has interesting electrophysical properties, due to which the material is promising for applications in supercapacitors, UV coatings with low refractive index, excimer laser mirrors, and photolithography. The formation of AlF3-based nano- and micro-wires can bring new functionalities to AlF3 material. AlF3 nanowires be used, for example, in functionally modified microprobes for scanning probe microscopy. In this work, we investigate the AlF3 samples obtained by the reaction of initial aluminum with aqueous hydrofluoric acid solution of different concentrations. All the samples were obtained under normal conditions. The morphology of the nanowire samples is studied by scanning electron microscopy. Quantitative energy-dispersive x-ray spectroscopy (EDS) spectra are obtained and analyzed with respect to the feedstock and each other.

: AlF3 has interesting electrophysical parameters, due to which the material is promising for applications in supercapacitors, UV coatings with low refractive index, excimer laser mirrors, and photolithography. The formation of AlF3-based nano- and micro-wires can bring new functionalities to AlF3 material. AlF3 nanowires be used, for example, in functionally modified microprobes for scanning probe microscopy. In this work, we investigate the AlF3 samples obtained by the reaction of initial aluminum with aqueous hydrofluoric acid solution of different concentrations. All the samples were obtained under normal conditions. The morphology of the nanowire samples is studied by scanning electron microscopy. Quantitative energy-dispersive x-ray spectroscopy (EDS) spectra are obtained and analyzed with respect to the feedstock and each other.

Antioxidants are molecules that neutralize free radicals. In general, the reaction mechanisms of antioxidants are well known. The main reaction mechanisms of antioxidants are electron transfer (ET), proton transfer (PT), H atom transfer (HAT) and radical adduction (RAF). The study of these mechanisms is helpful to understand how antioxidants control high free radical levels on the cell. There are many studies focused on determine the main mechanism of an antioxidant to neutralize a wide spectrum of radicals, mainly reactive oxygen species (ROS) type radicals. Most of these antioxidants are polyphenols type compounds. Some esters, amides and metal-antioxidants have shown antioxidant activity. There are few experimental and theoretical studies about the antioxidant reaction mechanism of the aforementioned compounds. In this work, we shown the reaction mechanism proposed of an amide and its metal-antioxidant counterpart. We show how the presence of the metal increase the electron transfer on polar media and the H transfer in non-polar media. Even though, esters and amides are non-polar compound, the scavenger activity is good for the metal-antioxidant compound in no-polar media

Using agronomic measures to remediate heavy metals on farmland is the main measure to achieve the safe utilization of crops. Investigating the effects of applying different fertilizers on the uptake, and translocation of Chromium (Cr) in maize and on the effectiveness of Cr in soil under Cr contamination of farmland is of great theoretical and practical significance to achieve the safe utilization of arable land and safe production of agricultural products. Under field trial conditions, different fertilizer types were set up, including ammonium sulfite, calcium-magnesium phosphate, and diammonium phosphate. locally formulated fertilizers (urea-ammonium phosphate-potassium chloride) serving as the control, with Biochar and conditioner PX5B were chosen to compare the impacts of each. To study the effects of different fertilizer types on maize yield, Cr content in the plant, bioconcentration factor, translocation factor and available content of Cr in the soil. The results showed that Compared with the formulated fertilizer, all treatments could improve pH, soil organic matter (SOM） and reduce the effective state of Cr content in the soil by 15.05% to 42.66%. While the Cr content of maize grains treated with biochar and conditioner PX5B was 0.80 mg·kg-1 and 0.88 mg·kg-1 with reduction rates of 39.95% and 33.83%, respectively. The Cr content of maize grains treated with various fertilizer treatments ranged from 0.82 to 1.32 mg·kg-1 with reduction rates of 0.75% to 38.19%. The Cr content of maize grains could be brought down to below the national food safety standards of China(1.0 mg·kg-1) using urea – calcium magnesium phosphate - potassium chloride, urea - diammonium phosphate - potassium chloride, ammonium sulfite – calcium magnesium phosphate - potassium chloride and ammonium sulfite, urea – calcium magnesium phosphate - potassium chloride and the two conditioner treatments. Among the different fertilizer treatments, the best fertilizer treatment for reducing the effective state Cr content of soil and the Cr content of maize grains was ammonium sulfite-calcium-magnesium-phosphate fertilizer-potassium chloride, which could achieve similar reductions as the two conditioners, while it also had a certain reduction effect on the Cr content in maize roots and straws and on the aboveground bioconcentration factor（BCF） and the root-to-straw translocation factor（PTF） of maize for Cr. Therefore, the combination of ammonium sulfite and calcium magnesium phosphate is the best fertilizer combination to block the absorption of Cr by maize and has some implications for the fertilization of farmland under acidic soil conditions of Cr contamination.

Heavy metals toxicity is a grave environmental issue in contemporary times. Phytoremediation is economic, effective and ecofriendly approach to decontaminate and remediate metal contaminated areas. Phenolic and Flavonoid content are important abiotic stress markers. The individual and combined impacts of toxiferous metals Arsenic (As), Cadmium (Cd) and (Copper) Cu were employed in recent studies to investigate their effect on Total flavonoids content (TFC) and total phenolic content (TPC) in various parts of Hydrocotyle umbellata L. to explore the role of plant in abating metal contamination. Folin- ciocalteu and AlCl 3 methods were used for investigating TPC and TFC respectively. Two-way ANOVA and CART model were employed for statistical analysis. Highest TPC was examined in decreasing order as leaf & gt; stem & gt; root in case of all the metals. Whereas highest TFC was found in all plant parts when subjected to As toxicity, and the lowest TFC was found in stem of the plant in respect to Cu toxicity. There was significant effect on TPC on plant part when subjected to Cu and As stress, but so significance was observed in plant part in case of Cd and combined metal stress. Treatment concentration had no significant effect on TPC when subjected to unique impact of all the three metals but had significant effect in case of combined metal stress. Similarly, in case of TFC no significant effect was recorded in case of plant part in all the stress types. But treatment amount has significant impact on Cd and combined metal stress. Metal type has significant effect on TPC and TFC. Whereas plant part has significant impact on TPC but non-significant values were observed on TFC in this case. This study epitomizes TPC and TFC in plants as effective and viable tool to pertain their role in phytoremediation against metal contamination. Therefore H. umbellata L. can be exerted for successful assemblage and decontamination of Cd, Cu and As in different plant parts.

Sequential reactions of aminoalkynes represent a powerful tool to easily assembly biologically important polyfunctionalized nitrogen heterocyclic scaffolds. Metal catalysis often plays a key role in terms of selectivity, efficiency, atom economy and green chemistry of these sequential approaches. This review examines the existing literature on the applications of reactions of aminoalkynes with carbonyls which are emerging for their synthetic potential. Aspect concerning the features of the starting reagents, the catalytic systems, alternative reaction conditions and the pathways as well as the possible intermediates are provided.

Abstract: Heavy metals (HMs) contamination is one of the main among abiotic factors affecting crop productivity and also threatens human health via consuming metal contaminated crops as a food source. Over the past few years, HMs have drawn a lot of attention due to their increased use for commercial purposes and their harmful effects on plants and other life forms, thus threatening human survival. However, in recent years, several methods have been adopted to combat the harsh effects of HMs. After phytohormones, use of mineral nutrients such as selenium (Se) in the prevention of HM stress has been explored by the researchers more recently. Selenium is an important micronutrient widely known for its antioxidant properties in both plants and animals. Exogenous Se inhibits metal uptake and its translocation and also improves the antioxidant system, thus imparts resistance to HM toxicity in plants. Moreover, Se also regulates the production of various osmolytes in cells that helps in developing cell osmolarity. Selenium also induces the production of different types of secondary metabolites (SMs) that are also involved in plant's secondary defense mechanisms to different stresses. Uptake of mineral nutrients is a vital process for plant growth and development, which is also positively correlated with Se under metalloid toxicity. However, in order to understand the exact mechanism of Se in HM tolerance, different metabolic processes stimulated by Se and their pathways need to be explored. Hence, this review focuses on the role of Se on nutritional status, antioxidants metabolism, interaction with phytohormones and its role in the regulation of various genes involved in Se induced HM tolerance. Thus, this study will help researchers in the future for the improvement of HM tolerance via Se application in plants.

Co-based catalysts have gained significant attention in recent years due to their excellent ability to activate C-H bonds and high selectivity towards olefins, despite being a non-noble and environmentally unfriendly metal. However, further improvements are necessary for practical utilization, particularly in terms of activity and anti-carbon deposition capacity. In this study, we synthesized Al₂O₃ nanorods with abundant pentacoordinated Al³⁺ (Al³⁺_penta) sites. The supported Co on the Al₂O₃ nanorod (Co/Al₂O₃-NR) exhibited higher selectivity (>96% propylene selectivity) and stability (deactivation rate 0.15 h^-1), compared to Co supported on an Al₂O₃ nanosheet with fewer pentacoordinated Al³⁺ sites. Various characterizations confirmed that Co(II) mainly exists as CoAl₂O₄ rather than Co₃O₄ in the form of Co/Al₂O₃-NR, which inhibits the reduction of Co(II) to Co0 and improves catalyst stability accordingly.

Metal halide perovskites (MHPs), in particular lead-based halide perovskites have earned a recognized fame in several fields for their outstanding optoelectronics properties including direct generation of free charge carriers, optimal ambipolar charge carrier transport properties, high absorption coefficient, point-defect tolerance, and compositional versatility. Nowadays, this class of materials represents a real and promising alternative of silica for the photovoltaic technologies. This worthy success led to a growing interest in the exploration of MHP materials in other hot research fields such as the solar-driven photocatalytic water splitting towards hydrogen production, CO2 reduction to CO and CH4, useful organic reactions such as organic synthesis (formation of C-C, C-N, and C-O bonds), and pollutants and dye degradation. Nevertheless, many of these perovskite materials showed air and moisture instability problems that considerably hinder their practical application for photocatalytic water splitting and photodegradation of CO2. Moreover, if the chemical instability is a problem that can be in part mitigated by the optimization of the lattice structure, the presence of lead represents a real problem for the practical application of these type of materials in commercial devices. To successfully overcome this problem, lead-free metal halide perovskites (LFMHPs) have gained increasing interest thanks to their promising optoelectronic properties, comparable to lead-based materials, and their eco-friendly nature. Among all the lead-free perovskite alternatives, this mini review will focus the attention on the bismuth-based perovskites and perovskite derivatives with specific focus on solar-driven photocatalysis application for H2 evolution.

Heavy metals contamination in groundwater often occurs in various industrial processes. Stud-ies have confirmed that polysulfide could reduce hexavalent chromium to trivalent chromium, achieving the effect of in-situ stabilization. For other heavy metals contamination in groundwa-ter, whether polysulfide also had a stabilizing ability to achieve in-situ remediation. This re-search focused on heavy metals except for chromium that often contaminated in groundwater, including lead, nickel, zinc, copper, and cadmium to explore the feasibility of using calcium polysulfide (CaSx) as an in-situ stabilization technology for these heavy metals contamination groundwater. Results showed that CaSx had a great removal efficiency for heavy metals lead, nickel, zinc, copper, and cadmium. However, for nickel, zinc, copper and cadmium, when CaSx was added excessively, complexes would be formed, causing the result of re-dissolve and this would also reduce the removal efficiency. Since it is difficult to accurately control the dosage of agents for in-situ groundwater remediation, the concentration of re-dissolved nickel, zinc, cop-per, and cadmium may not be able to meet the groundwater control standards. CaSx had high lead removal efficiency, and it would not cause re-dissolution due to excessive CaSx dosing. CaSx can be used as an in-situ stabilization technique for lead contaminated groundwater.

The purpose of this study was to arrange a green roof on a sheet metal house to achieve winter heat preservation and summer thermal insulation using different plants and soil media, and to maintain the advantage of cost-saving and quick installation of sheet metal houses. In terms of the research method, the roof insulation, heat preservation and plant growth index were tested. Plants were grown in 10 container-type green roofs on the sheet metal house roof, and the physical environment of the building was monitored for one year. Five containers of commercially-available culture soil and five containers of sustainable composite were used as the media for growing five kinds of plants, respectively. The control group only had a sheet metal house roof. There were 11 experimental modules for testing whether the green roofs had thermal insulation, heat preservation and plant growth effects on a general sheet metal house. The results showed that, regarding the thermal insulation benefit assessment, the Sedum acre cv. robustum of green roof Groups B to D caused the temperature to be 38.29°C lower than the surface of the simple sheet metal house roof in August, showing a temperature difference of 54%.

The Anderson insulating states in Au nanoparticle assembly are identified and studied under the application of magnetic fields and gate voltages. When the inter-nanoparticle tunneling resistance is smaller than the quantum resistance, the system showing zero Mott gap can be insulating at very low temperature. In contrast to Mott insulators, Anderson insulators exhibit great negative magnetoresistance, inferring charge de-localization in a strong magnetic field. When probed by the electrodes spaced by ~200 nm, they also exhibit interesting gate-modulated current similar to the multi-dot single electron transistors. These results reveal the formation of charge puddles due to interplay of disorder and quantum interference at low temperatures.

Intermetallic compounds are increasingly being expected to utilize in tribological environments, but to date the works are hindered by insufficient ductility at low and medium temperature. This paper presents a novel multiphase intermetallic alloy with the chemical composition of Mo-40Ni-13Si (at.%). Microstructure characterization reveals that a certain amount of ductile Mo phases formed during the solidification process of ternary Mo-Ni-Si alloy melt, which is undoubtedly beneficial to the ductility improvement of intermetallic alloy. Tribological properties of the designed alloy, including wear resistance, friction coefficient and metallic tribological compatibility, were evaluated under dry sliding wear test conditions at room temperature. Results suggested that the multiphase alloy possesses an excellent property for room-temperature wear applications, which is attributed to the unique microstructural features and thereby good combination in hardness and ductility. The corresponding wear mechanism is also reported by observing the worn surface, subsurface and wear debris of alloy, which to be found is soft abrasive wear.

Oil and petroleum are strategic resources of great importance to national security. Petroleum and hydrothermal gold deposits may form together, with similar evolutionary trends in their formation, migration, and enrichment. Petroleum reservoirs and gold deposits are closely coupled under certain geological conditions. The solubility of gold in crude oil and its forms of occurrence are important in determining the mechanisms of interaction between gold and petroleum and in facilitating the recovery of gold from gold-bearing petroleum. In this study, the occurrence of gold in crude oil from the Linnan Depression in the Bohai Bay Basin, China, was studied using inductively coupled plasma–mass spectrometry and X-ray photoelectron spectroscopy. Concentrations of gold in crude oil from the Linpan and Shanghe oilfields averaged 44.5 ppb, which is well above the minimum concentration required for hydrothermal gold mineralization. Gold has an affinity with carbon, oxygen, and sulfur, and its concentration in crude oil is positively correlated with total acid and sulfur contents. We speculate that gold may exist in crude oil as complexes with organic acids or thiols, with crude oil thus being a transport medium for gold.

Life Cycle Cost Analysis is a method used to assess long-term economic efficiency among equivalent competing processes or products. The purpose of the paper is to investigate the nature and level of costs for an organic orchard located in Southern Romania, using a complex approach covering the entire chain of production, through the life span. The research results, based on a dynamic analysis and an integrated evaluation of the orchard's performance, have been ranked on investment and operational costs, broken down on three categories (establishment and production, post-harvest and transport costs). The highest cost, representing 151726 euros/ha/20 years, about 52.72% of the total operational costs and 50.4% of the total farm costs/ha/20 years, was recorded in exploitation stage. The scenarios for the sensitivity analysis considered different levels of average yield (40, and, respectively 60 tons/ha) with different rate of sold production (85%, optimistic scenario; 70%, pessimistic scenario). The hotpoints identified at the production stage were use of agricultural machinery, several pesticides, the costs of seedlings, anti-hail net, plastic boxes and labor cost, while at the post-harvest stage, were those related to labor and energy consumption. The transport stage has had important costs with tractor operation and the track.

Organic fertilizers are fertilizers made from organic materials which are partly or wholly derived from waste materials, the function of these fertilizers is to improve the physical, biological, and chemical properties of the soil, these fertilizers are processed through the composting process, these fertilizers are very much needed because they are difficult to obtain at a high price. expensive. This study aims to obtain data on the growth and yield of sweet corn, due to the use of agricultural waste as organic fertilizer. The research method was experimentally consisting of 5 treatments and 5 replications; ie P0 = Without organic fertilizer (control) P1 = Dosage of organic fertilizer 2.5 tons/ha, P2 = Dosage of organic fertilizer 5 tons/ha P3 = Dosage of organic fertilizer 7.5 tons/ha, P4 = Dosage of organic fertilizer 10 tons /ha using a Randomized Block Design (RBD) The results showed that organic fertilizer had a significant effect on plant height aged 30, 40 and 50 DAP, had a very significant effect on cob length at a dose of 10 t.ha-1 and, had no significant effect on cob weight, will still have a high weight of 350 g.cob-1 From this description it can be concluded that organic compost can be used as a substitute for chemical fertilizers which provides an increase in the growth and production of sweet corn plants at the use of 10 tons/ha.

Coating of organic molecules from the solution phase can result in directional crystal growth under certain conditions, even on a smooth isotropic surface and without the need of any kind of graphoexpitaxial preparation of the substrate. Based on reviewing the results from a variety of coating techniques and conditions, we identify the condition that the coating speed should equal the growth speed of the fastest growing crystal plane as crucial for achieving a high degree of directional crystallization.

Composting is one of the most economical and environmentally safe methods of recycling organic waste. Soil microorganisms play a significant role in decomposition and the availability of plant nutrients. This study was designed to prepare a suitable microbial inoculum and its evaluation on composting heap to decrease the time of waste degradation. The bacteria were isolated and molecular characterized from the soil near composting area by using 16S ribotyping technique. The identified strains of bacillus cereus used as an inoculum gives better results to expedite the degradation of organic waste. The prepared bacterial inoculum with molasses was also compared with commercial inoculum by optimizing physical and chemical parameters (temperature, oxygen, C: N, pH, and moisture content) of composting heap. Monthly reading of these parameters was taken from experimental and control treatments. The highest decomposition rate of organic waste was recorded in treatment A (experimental heap) where molasses and bacterial inoculum were added and less decomposition was observed in treatment D (experimental heap) where no inoculum and molasses were added. It was concluded from the studies that the prepared bacterial inoculum with two strains of Bacillus was effective and prepared mature compost in 2.5 months by increasing decomposition efficiency of organic waste. Furthermore, the prepared compost was also sustainable in its physical and chemical characteristic.

Even in the first quarter of XXI century, the presence of organic dyes in wastewaters is a normal occurrence in a series of countries, and being these compounds toxics, their removal from these waters is of a necessity. Among the separation technologies, adsorption processing appeared as one of the most widely used to reach this goal. The present work reviewed the most recent approaches (first half of 2021 year) about the use of a variety of adsorbents on the removal of, also, a variety of organic dyes of different nature.

The main aim of the study was to analyze/determine how international modern retailers’ chains can achieve a competitive advantage by introducing private labels (PLs) in the organic category and in turn stimulate consumption of food produced with respect of sustainability principles. Following a review of the relevant literature data collection process involved two steps. First, to select retailers with organic private labels (OPLs) and producers delivering products under OPLs, there were conducted in-depth semi-structured interviews with the representatives of the management board of 17 enterprises. A group of 6 enterprises was selected, including 3 retailers having OPLs, 2 producers delivering products under OPLs and one enterprise that was categorized as producer and distributor. Based on the results of the interviews, six sources of the competitive advantage of the OPLs were identified and further discussed. Second, to analyze more in depth assortment-based competitive advantage of the OPLs, 8 enterprises (5 retailers having OPLs, 2 producers delivering products under OPLs and one enterprise categorized as a producer and distributor) were approached for the interviews. To explore price-related competitive advantage three products offered under the premium PLs, the economy PLs, the organic PLs, the producer brands and the imported brands were selected for the subsequent analysis. Increasing competition in the food retailing sector pose many challenges on the retailers and stimulate them to develop the PLs that is in line with global trends. In case of the OPLs, the more popular strategy while introducing them is to differentiate the PLs with quality and image related attributes comparable to leading producer brands. Retail chains introducing the OPLs achieve the competitive advantage related to six sources: price, range of assortment, type of PLs, image of retailer, sustainability and specific process and product related attributes of organic food. Additionally the retailers use their reputation and image of retailers’ brand to guarantee the quality of new organic products introduced under the PLs. To achieve or maintain the competitive advantage, retailers tend to introduce the OPLs positioned as value added PLs. They perceive the OPLs as a way to influence the consumers' decision to buy and increase their loyalty towards store brands. The strategies of the retailers evolve and the largest retailers decided to create the premium OPLs, the others focus on introduction of the international OPLs or aim at development of new PLs based on the analysis of consumers' preferences. There are several factors behind the decision to introduce or extend the premium OPLs i.e. to expand the assortment of organic products and green products line, to increase category margins and to enhance retailer’s image among customers. Other large retailers create the OPLs with special product line design focusing on health- and environmental related attributes and high quality guaranteed by the organic regulations and the certification. The process of the introducing the premium PLs should be influenced by the inherent characteristic of organic food and its production methods that respect the principles of the sustainable development.

A recent breakthrough in preparation of immobilized enzyme based biocatalysts achieving highly enhanced enzymatic activities and stabilities has become a great alternative to conventional immobilization techniques. The functional hybrid nanobiocatalysts (FHNs) fabricated in this immobilization composed of organic components (amino acid, peptide, protein, enzyme and plant extract) and inorganic components (various metal ions) give flower-like morphology with narrow size distribution and porous structure. The enzyme incorporated FHNs exhibite greatly enhanced catalytic activities and stabilities compared to free and conventionally immobilized enzymes under various experimental conditions. In addition to that, the FHNs consisting of other organic components act as Fenton-like reagents and show peroxidase-like activity owing to presence of metal ions and porous structure in the FHNs. This report basically focuses on preparation, characterization, and bioanalytical applications of the FHNs and explain mechanism of the FHNs formation and thier enhanced activities and stabilities.

Rising organic charge in northern freshwaters is attributed to increasing levels of Dissolved Natural Organic Matter (DNOM) and shifts in water chemistry. Organic charge concentration may be determined by charge balance calculations (Org.-) or modelled (OAN-) using the conceptual Oliver and Hruška models based on the density of weak acid functional sites (SD) present in DNOM. The charge density (CD) is governed by the SD and protonation and complexation reactions on the functional groups. The models use this SD as a key parameter in empirically fitting the model to Org.-. Utilizing extensive datasets of water chemistry, this study shows that spatial and temporal differences in SD and CD are influenced by variations in the humic-to-fulvic ratio of DNOM and the organic aluminum (Al) complexation, as well as the mole fraction of CD to SD governed by the acidity. Site median SD obtained for 44 long-term monitored acid-sensitive lakes was 11.1 and 13.9 µEq/mg C for the Oliver and the Hruška model, respectively. During the 34 years of monitoring the CD increased by 70%, likely due to rising pH and declining Al complexation with DNOM. Present-day median SD values for the Oliver and Hruška models in 16 low-order streams are 13.8 and 15.8 µEq/mg C, respectively, and 10.8 and 12.5 µEq/mg C, respectively, in 10 high order rivers.

SOC stock (SOCS) changes caused by land use changes are still unclear, and understanding this response is essential for many environmental policies and land management practices. In this study, we investigated the temporal-spatial and vertical distribution characteristics of SOCS on the Western Sichuan Plateau (WSP) using the sparrow search algorithm-random forest regression (SSA-RFR) models with excellent model applicability and accuracy. The temporal-spatial varia-tions in the SOCS were modeled using 1080 soil samples and a set of nine environmental covariates. We analyzed the effect of land use changes on the SOCS on the WSP. The total SOCS increased by 18.03 Tg C from 1990 to 2020. The results of this study confirmed that the SOCS in the study area has increased significantly since 2010, with an increase of 27.88 Tg C compared to the total SOCS in 2010. We found that the spatial distribution of the SOCS increased from southeast to northwest, and the vertical distribution of the SOCS in the study area decreased with increasing soil depth. Forest and grassland are the main sources of SOCS, the total SOCS in the forest and grassland accounted for 37.53 and 59.39% of the total SOC pool in 2020, respectively. Expansion of the wetlands, forest, and grassland areas could increase SOCS in the study area.

Current paper is aiming to show the obtained results in manufacturing and characterization of graphite-based and metal composite materials suitable to be used in high voltage application of automotive field. Thus, 4 types of materials have been processed and tested in order to assess their suitability to be used as current collector material for trolleybus. The novelty of this work is the new innovative technological process for obtaining the carbon/metal composite material used in the manufacture of sliding contacts for electrical current collector heads, as well as the character-istics obtained for this material. All 4 obtained materials have been characterized from structural (by optical microscopy), mechanical (density, electrical resistivity, hardness) and functional point of view (wear after 1000 working hours, electric discharge and electric load) and it was determined that the material which uses chemically copper covered graphite is the most suitable of them and has been chosen to be further developed by the end beneficiary.

In this study, Al-Al4C3 compounds were manufactured by mechanical milling followed by heat treatment. To analyze the microstructural evolution, the composites were sintered at 550°C during different sintering times of 2, 4 and 6 hours. The mechanical results suggest that dislocation density and crystallite size primary contribute to hardening before the sintering process, with a minimal contribution from particle dispersion in this condition. The compound exhibited a significant 75% increase in hardness after 2 hours of sintering, primarily attributed to the nucleation and growth of Al4C3 nanorods. The HRTEM analysis, combined with ge-ometric phase analysis (GPA) at and near the Al-Al4C3 interface of the nanorods, revealed strain field distributions primarily associated with partial screw dislocations and the presence of closely spaced dislocation dipoles. These findings are consistent with the microstructural parameters determined from X-ray diffraction pattern analysis using the convolutional multi-ple whole profile (CMWP) method. This analysis showed that the predominant dislocation character is primarily of the screw type, with the dislocation dipoles being closely correlated. Based on these results, it is suggested that samples with a lower weight percentage of rein-forcement and longer sintering times may experience reduced brittleness in Al/Al4C3 compo-sites. Strengthening contributions were calculated using the Langford–Cohen and Taylor equations.

In this review we explore the recent progress in catalytic materials for ammonia synthesis that are based on metal nitrides and other catalytic surfaces. It comprises a detailed overlook of various techniques used in ammonia synthesis research and the state-of-the-art modeling techniques employed to investigate new reaction mechanisms and more efficient processes for sustainable ammonia synthesis production. The review is discussed in the context of reaction mechanisms developed and recent progress that has been made with respect to thermal, electrochemical and photocatalytic ammonia synthesis.

Sustainable soil quality management is one of the most important approaches in ensuring high agricultural productivity and safe quality produce. With the current rising application of inorganic fertilizers and chemical pesticides, degradation of agricultural soils is becoming a global phenomenon, attracting attention of many researchers. The present study hypothesized that with the increasing chemical pesticide and fertilizer application under various cropping systems, there is potential for increased toxicity of heavy metals residues above background concentrations and their associated complexes and intermedia transfer between environmental compartments in large-scale farms in Kenya. Using standard methods, 204 soil samples collected from five distinct cropping systems were analyzed for PH, Electrical Conductivity, exchangeable base cations (Na+, Mg2+, K+, Ca2+), Cu, Pb, Zn, Cd, Fe, Cr, Total Organic Carbon and Total N and data analyzed using Genstart, version 23.1. The concentrations of Zn, Cu, Pb and Fe were lower than the globally acceptable levels hence less soil pollution threat (NPI<1). However, Cd concentration exceeded permitted levels (NPI>1). Among the cropping systems considered, Maize and sugarcane cropping systems were the most susceptible to heavy metal pollution. In conclusion, the rank order of the pollution potential associated with heavy metal contamination in the study area is Cd>Zn>Pb>Cu>Cr>Fe.

The indole nucleus is an important element of many natural and synthetic molecules with significant biological activity. Nonetheless, the co-presence of transitional metals in organic scaffold may represent an important factor in the development of effective medicinal agents. This review covers some of the relevant and recent achievements in the biological, chemical and pharmacological activity of important indole-based metal complexes in the area of drug discovery.

At this time, nanoparticles used to been considered for various biomedical applications due to their particular properties[1, 2]. It is already known that one of the major advances in the relative application of nanoparticles is the recognition of the steric stabilization which can increase the particle stability in the biological environment and provide the opportunities of the application of nanoparticles in the development of drug delivery systems (DDSs) for achieving drug targeting and controlled drug release. Nano crystalline silver particles (AgNPs) have major applications in biomolecular recognition of highly sensitive, anti-microbial treatment, catalysis and manufacture sensors [3-7]. The NPs for various applications medical like image quality, medicine, tissue, magnetic resonance imaging (MRI) of targeting tissues and cells styles. This is particularly the case of AgNPs significantly encompasses the whole a wide range of industrial and medical applications. In this study, we have been synthesized incorporated omeprazole and omeprazole sulfide drugs with AgNPs and the results was investigated with TEM, FT-IR, DRS and XRD. The particle size has been seen in imaging TEM about 80 nm. Moreover either Omeprazole@AgNPs or omeprazole sulfide@AgNPs are able to excrete bacteria. In this study, the antibacterial properties of drugs with silver nanoparticles also increased.

Hydrogen energy is regarded as an auspicious future substitute to replace fossil fuels, because of its environmentally friendly characteristics and high energy density. In the pursuit of clean hydrogen production, there has been a significant focus on the advancement of effective electrocatalysts for the process of water splitting. Although noble metals like Pt, Ru, Pd and Ir are superb electrocatalysts for the hydrogen evolution reaction (HER), they have limitations for large-scale applications, mainly high cost and low abundance. As a result, non-precious transition metals have emerged as promising candidates to replace their more expensive counterparts in various applications. This review focuses on recently developed transition metal phosphides (TMPs) electrocatalysts for the HER in alkaline media due to the cooperative effect between the phosphorus and transition metals. Finally, we discuss the challenges of TMPs for HER.

Early debridement and stabilization for pyogenic spondylodiscitis allow early mobilization of the patient and prevent subsequent spinal deformity. Tantalum (Ta) trabecular metal (TM) components have several potential advantages over conventional implant materials, such as its uniformity and structural continuity, strength, low stiffness, high porosity, high coefficient of friction and tantalum trabecular metal enhances the host defense mechanism by increasing leukocyte chemotaxis, phagocytosis, and the bacterial killing rate. A single-stage surgery with a tantalum trabecular metal cage combining two different approaches is sufficient to maintain vertebral stability. This retrospective cohort study included 57 patients, 31 (54%) patients were treated with single-stage debridement and reconstruction with trabecular metal cages, and 26 (45.6%) patients received spine surgery without trabecular metal cages received surgery between January 2018 and March 2021 in our tertiary academic teaching hospital. The CRP values dropped borderline significantly in the TM cage group compared with the non-TM cage group postoperatively. In patients with spondylodiscitis, it is advisable to perform single-stage debridement and reconstruction with a trabecular metal cage, which allows abscess drainage and rapid mobilization, prevents deformity.

The nature abundant sodium metal is proposed as ideal anode materials for advanced batteries due to its high specific capacity of 1166mAh g-1 and low redox potential of -2.71V. However, the uncontrollable dendritic Na formation and low coulombic efficiency are still major obstacles for applications. Notably, the unstable and inhomogeneous solid electrolyte interphase (SEI) is recognized to be the root cause. As SEI layer plays a critical role in regulating uniform Na deposition and improving cycling stability, researches on SEI modification, especially the artificial SEI modifications has been extensively investigated recently. In this regard, we discussed the advances on artificial interface engineering from the aspects of inorganic, organic and hybrid inorganic/organic protective layers. Finally, we also highlighted the conclusions and key prospects for further investigations. We hope this review can provide a new insight for sodium metal protection.

The need to regulate the non-exhaust particulate emissions from vehicles has been discussed worldwide due to the toxicity to the human body as well as the atmosphere. In-depth studies have been conducted on precise analysis of the non-exhaust particulates, in particular, accurate measurement of tire-brake-road wear particles, and their proportion in the atmosphere. In this study, the influence of tire and road wear particles (TRWP) on particulate matter (PM) in the atmosphere was investigated through tire and PM samples. PM samples were collected from the atmosphere using a high-volume sampler equipped with a quartz filter. Additionally, polycyclic aromatic hydrocarbons (PAHs) and heavy metals in tire rubber were analyzed as markers by pyrolysis-gas chromatography/mass spectrometry (GC/MS), GC/MS, and inductively coupled plasma/mass spectrometry (ICP/MS). More vinylcyclohexene was detected than dipentene in the markers measured in the samples of tires equipped with vehicles driving on the road with the high-volume sampler installed, while more dipentene was detected in total suspended particles (TSP) samples. Among the PAHs measured in tire samples, pyrene exhibited the highest concentration. In TSP samples, benzo(b)fluoranthene showed the highest concentration. Among the heavy metals, zinc exhibited the highest concentration in all tire samples and calcium in TSP samples.

Over the centuries, honey is known for its superior usage in culinary, and for its rich nutrition and therapeutic values which are scientifically proven in the medical field. The chemical composition of honey varies depending on its botanical sources and environment. Therefore, the nutrition content in honey is highly likely to be affected by contaminants, such as heavy metals and pesticides. To ensure the quality of honey, parameters such as the heavy metal content should be within the safe range of total standard mineral and trace elements as defined by the International Food Standard (Codex Alimentarius), and pesticides should not be present at all. The high concentration of heavy metal and pesticides not only deteriorates the quality and quantity of honey, but also causes harm to the bee colony itself. In the agriculture sector, the excessive usage of pesticides and fertilizer negatively impacts the overall honey production process. Bees, a pollinating agent, bring the polluted nectar back to their beehives, eventually contaminating the honey and depreciating its value. Hence, this article will comprehensively review the activities that contribute to heavy metal and pesticide contamination, the interactions of bees as a pollinating agent, the impact of the pollutant to the colonies, and subsequently to the honey production.

The Katangese Copperbelt area (KCA) located south-eastern of D.R. Congo presents high concentration of metal trace elements (MTE) in several soils due to a rich natural geochemical background, and intense mining activities, causing serious health issues to humans and animals. However, the lack of data on specific baseline concentrations makes it difficult to properly assess and monitor the environmental quality of soils in the region. In this study, the baseline concentration of 11 potentially toxic MTE (i.e., Mn, Zn, Cu, Co, Cr, Pb, Cd, Ti, Ni, Al, and Fe) was assessed in topsoils of the KCA, and the possible influence of land uses (croplands, forest and mining areas) was examined. Results showed the following baseline concentrations, i.e. lower and upper limits (mg.kg^-1) in cropland soils : Al (18.4–162.0), Cd (0.0–0.1), Co (0.1–3.5), Cu (0.8–17.7), Cr (0.0–0.2), Fe (4.7–233.8), Mn (3.5–575.6), Ni (0.1–1.9), Pb (0.2–2.4), Zn (0.1–20.3), Ti (0.0–392.6); in forests: Al (18.8–1167.1), Cd (0.02–0.48), Co (0.20–18.1), Cu (3.6–42.7), Cr (0.1–33.7), Fe (86.4–283.3), Mn (4.9–1538.9), Ni (0.05–24.2), Pb (0.3–13.7), Zn (2.0–7.0), Ti (0.2–0.8); and in mining areas: Al (7.4–241.2), Cd (0.01–164.8), Co (0.2–211.3), Cu (2.4–5485.4), Cr (0.03–0.4), Fe (5.9–481.6), Mn (7.1–95.9), Ni (0.1–1.9), Pb (0.2–390.8), Zn (1.5–5629.3), Ti (0.1–1.3). Cu and Zn were highest in mining areas demonstrating a prevalent influence of mining activities in altering the natural background of metals concentrations in the region. By contrast, croplands and forest shared a similar trend of Al and Mn contents, suggesting a mild influence of agricultural activity. Intriguingly, higher Cu and Co contents were found in forest compared to croplands. For all the three studied land uses, no straightforward relation was found between metal concentrations and soil total acidity. This study is the first attempt to establish reference values of MTE contents in the KCA soils and thus provides valuable information for legislative purposes and for soil quality assessment.

Metal toxicity in soils, along with water runoff, are increasing environmental problems that affect agriculture directly and, in turn, human health. In light of finding a suitable and urgent solution, research on plant treatments with specific compounds that can help mitigate these effects has increased, and thus the exogenous application of melatonin (MET) and its role in alleviating the negative effects of metal toxicity in plants, have become more important in the last few years. MET is an important plant-related response molecule involved in growth, development, and reproduction, and in the induction of different stress-related key factors in plants. It has been shown that MET plays a protective role against the toxic effects induced by different metals (Pb, Cd, Cu, Zn, B, Al, V, Ni, La, As, and Cr) by regulating both the enzymatic and non-enzymatic antioxidant plant defense systems. In addition, MET interacts with many other signaling molecules, such as reactive oxygen species (ROS) and nitric oxide (NO), and participates in a wide variety of physiological reactions. Furthermore, MET treatment enhances osmoregulation and photosynthetic efficiency and increases the concentration of other important antioxidants such as phenolic compounds, flavonoids, polyamines (PAs), and carotenoid compounds. Some recent studies have shown that MET appeared to be involved in the regulation of metal transport in plants, and lastly, various studies have confirmed that MET significantly upregulated stress tolerance-related genes. Despite all the knowledge acquired over the years, there is still more to know about how MET is involved in the metal toxicity tolerance of plants.