Previously, various techniques have been proposed for reducing the lift-off effect on the thickness measurement of the non-magnetic films, including the peak-frequency feature and phase feature in the Dodd-Deed analytical formulation. To realise a real-time feedback response on the thickness monitoring, the phase term in the Dodd-Deeds formulation must be taken off the integration. Previous methods were based on the slow change rate of the phase term when compared to the rest of the term – the magnitude term. However, the change rate of the phase term is still considerable for a range of working frequencies. In this paper, a high-frequency feature has been found. That is, the ratio between the imaginary and real part of the phase term is proportional to the integral variable under high frequencies. Based on this proportion relationship, the phase term has been taken out; and a thickness algorithm has been proposed. By combing the measured impedance from the custom-built sensor (three coils), the thickness of the metallic film can be reconstructed. Experiments have been carried out for the verification of the proposed scenario. Results show that the thickness of the metal film can be reconstructed with a small error of less than 2 %, and immune to a reasonable range of lift-offs.

Aluminum wire is a common material for wire bonding due to its resistance to oxidation and low price. It does not melt when becoming a free air ball (FAB) during the electronic flame-off (EFO) process with wettability, and is applied by wedge bonding. This study used 20μm Zn-Coated Al-0.5wt.%Si (ZAS) wires to improve the FAB shape after the EFO process, while maintaining stability of the mechanical properties, including the interface bonding strength and hardness. In order to test circuit stability after ball bonding, the current-tensile test was performed. During the experiment, it was found that 80nm ZAS with wire bonding has lower resistance and higher fusing current. For the bias tensile test, the thicker Zn film diffused into the Al-Si matrix easily, after which the strength was reduced. The ball-bond interfaces had no change in their condition before and after the bias. Accordingly, ZAS could be a promising candidate for ball bonding in the future.

Groundwater flow and transport models are essential tools for assessing and quantifying the mi-gration of organic contaminants at polluted sites. Uncertainties in the hydrodynamic and transport parameters of the aquifer have a significant effect on model predictions. Uncertainties can be quantified with advanced sensitivity methods such as Sobol’s High Dimensional Model Reduction (HDMR) and Variogram Analysis of Response Surfaces (VARS). Here we present the application of VARS and HDMR to assess the global sensitivities of the outputs of a transient groundwater flow model of the Gállego alluvial aquifer which is located downstream the Sardas landfill in Huesca (Spain). The aquifer is subject to the tidal effects caused by the daily oscillations of the water level in the Sabiñánigo reservoir. Global sensitivities are analysed for hydraulic heads, aquifer/reservoir fluxes, groundwater Darcy velocity and hydraulic head calibration metrics. Input parameters in-clude aquifer hydraulic conductivities and specific storage, aquitard vertical hydraulic conductiv-ities, and boundary inflows and conductances. VARS, HDMR and graphical methods agree to identify the most influential parameters which for most of the outputs are the hydraulic conduc-tivities of the zones closest to the landfill, the vertical hydraulic conductivity of the most permeable zones of the aquitard, and the boundary inflow coming from the landfill. The sensitivity of heads and aquifer/reservoir fluxes with respect to specific storage change with time. The aquifer/reservoir flux when the reservoir level is high shows interactions between specific storage and aquitard conductivity. VARS and HDMR parameter rankings are similar for the most influential parameters. However, there are discrepancies for the less relevant parameters. The efficiency of VARS was demonstrated by achieving stable results with a relatively small number of simulations.

Although tourism seasonality significantly influences the livelihood activities of rural tourism households, limited research has explored how they adapt their livelihood strategies to achieve optimal outcomes. Employing an exploratory sequential mixed-methods design that combines thematic analysis and fuzzy-set Qualitative Comparative Analysis (fsQCA), we investigated the relationship between the livelihood strategies and outcomes of rural tourism households under the influence of tourism seasonality at the Guilin Karst World Heritage Site. The results indicate that livelihood strategies adopted by rural tourism households include "Tourism Persistence,” "Seasonal Employment,” and “Seasonal Farming” during the off-season, and “Extending Working Hours,” “Increasing Staffing Input,” and “Increasing Capital Input” during the peak season. Furthermore, these strategies form flexible combinations to realize livelihood outcomes, with “Extending Working Hours” being a necessary condition. The findings also revealed that the four configurations of seasonal livelihood strategies in the two patterns significantly contributed to high livelihood outcomes. One is named “Peak-Season Driven Pattern,” where “Extending Working Hours” and “Increasing Staffing Input” are the core conditions; the other is named “Peak-Off Blend-Driven Pattern,” where “Extending Working Hours,” “Increasing Capital Input,” and the absence of “Tourism Persistence” are the core conditions. These findings provide theoretical and practical insights for sustainable livelihood research.

There was no significant difference in bacterial adhesion between the 3 bone graft types tested, regardless of the bacterial strain used (p > 0.22). After 72 hours of culture, there was no significant difference between the Fresh and Frozen bone groups, while the number of CFU in the Decellularised group was significantly lower (p < 0.01), averaging -0.72 +/- 0.08 lg, -0.20 +/- 0.01 lg and -0.78 +/- 0.48 lg with S. epidermidis, S. aureus and E. coli respectively. Absolute values differences are low, and considering fresh bone (equivalent to autograft) as the gold standard due to its low infection rates in clinical studies, we can conclude that adhesion and biolfilm development characteristics are similar between Fresh, Frozen and Decellularised bone grafts..

Background: Exclusively breastfeeding your newborn while in the hospital is imperative for suc-cessful breastfeeding at home. This study will investigate if having a nurse on-site during rooming-in can enhance the proportion of exclusive breastfeeding. Methods: We carried out a prospective cohort study to assess exclusive breastfeeding in the first three months of life among two Neona-tology Units in Southern Italy with different hospital settings. The Ente Ecclesiastico Miulli of Ac-quaviva delle Fonti had on-site nurses available 24/7 (on-site group), while the Policlinico of Bari had nurses available on call 24/7 from the Neonatology Unit (on-call group). Results: Between January 3rd and March 31st, 2018, a total of 564 sets of mothers and babies were admitted - 299 on-site and 265 on-call. The exclusive breastfeeding rate for the entire group was 76.4% at 90 days, demonstrating the positive impact of rooming-in and nursing, regardless of the setting. Infants delivered via ce-sarean section in the on-site group demonstrated higher rates of exclusive breastfeeding at both 30 and 90 days of life. Conclusions: Our research indicates that having a nurse available at all times is crucial for promptly identifying any problems with breastfeeding. We highly suggest having an on-site nurse present during rooming-in for mothers who have had a caesarean delivery. This nurse should continuously promote exclusive breastfeeding until the baby is three months old.

Since 2017 Cartagena UNESCO World Heritage has threatened to be categorized as "in Danger" by UNESCO. This research analyzes two main critical aspects, Governance and Current state of the Site. Regarding Governance, the study aims to identify strengths, weaknesses, opportunities and treats in the UNESCO Site. Exemplary heritage management systems are studied to propose an adaptable management approach specifically for Cartagena. On the other hand, a comprehensive analysis is conducted utilizing a photographic report that highlights the major issues arising from inadequate heritage management. Hyperspectral images obtained from a previous study are employed to identify vegetation and asbestos-cement roofs within the cultural heritage Site. The study reveals that the ambiguity surrounding decision-making authority for heritage management, distributed between the Mayor's Office and the Ministry of Culture, is a primary challenge. This fragmentation has resulted in duplicated efforts and a lack of coordinated action, significantly compromising the conservation and protection of the cultural heritage Site. Moreover, twelve current shortcomings of cultural heritage in Cartagena are identified through authors' five-year on-site regular visits, photographic reports and observation. To address the prevailing concerns, a new line of command for cultural heritage management is proposed as the most effective means of tackling these challenges. Additionally, general recommendations are presented to mitigate the existing problems and prevent the classification of Cartagena's heritage as "at risk" by UNESCO in the near future. This research provides a scientific perspective, drawing upon years of experience studying heritage and residing in the city, devoid of political influences or conflicts of interest.

ABSTRACT Background Ubiquitination plays an important role in protein post-translational processes and has been found to be involved in a number of regulatory functions including proteasome degradation, DNA repair, transcription, signal transduction, endocytosis, and sorting. As the identification of ubiquitination site is critical to furthering our understanding of the mechanism of ubiquitination, various experimental and machine learning methods have been used to conduct this task. It has been an important but challenging task to improve the accuracy of ubiquitination site prediction. In this research, we explore the possibility of improving the prediction performance of machine learning by incorporating grid search in the training process. Method We developed grid search procedures for each of six widely used machine learning methods including NB, LR, DT, SVM, LASSO, and KNN, and applied them to ubiquitination site prediction using the six PCP datasets that were previously developed. For each of the ML methods, we developed a set of values for each of the tunable hyperparameters available to the method. These sets of values then can be combined to form a large grid of hyperparameter settings, and each of these settings is used in the grid search. We integrated 5-fold cross-validation in grid search to train and test ML models and applied an additional independent validation procedure by conducting a pre-training 80-20 sample split. We evaluated the performance of the six methods by comparing them side by side for each of the six datasets. We also compared the grid search results with the results that were previously published without doing grid search. To optimize the prediction performance, we trained 1.1 million ML models in total through grid search. Results We compared the overall prediction performance of these six methods, as well as their prediction performance when working with balanced vs. imbalanced data, and large-scale vs. small-scale data. From the perspective of dataset, we find that the overall performance of every PCP dataset has been significantly improved in this study compared to the previous study, with the percentage increase of the average AUC of all six datasets ranging from 7.9% (PCP-4) up to 17.0% (PCP-1). From the perspective of method, we find that three out of four methods significantly benefit from grid search comparing to their previously published non-grid search results, with the maximum AUC improvement as high as 47% (LASSO on PCP-5), 43.3% (NB on PCP-1), and 33.7% (SVM on PCP-6). SVM overall ranks number one, followed by KNN as the number two performer based on their average AUCs on all datasets. But these two also ranked the top two (KNN 76 days and SVM 15 days) in terms of the total running time that they need to do grid search. We also find that SVM, KNN, and DT tend to handle small-scale and imbalanced datasets better, while LR, and LASSO are doing well with large-scale and balanced datasets. NB is more sensitive to data imbalance while less sensitive to the size of a dataset. Conclusions Our results show that using grid search has improved the performance of ubiquitination prediction significantly. We find that the performance of a method is closely related to its hyperparameter setting and the type of data it handles. Even though SVM is on average an outperformer, none of the methods can provide the best performance for all datasets. When sufficient computing resources are well accessible, grid search is an effective way to identify both a top performing model for a machine learning method and a suitable machine learning method for a particular dataset.

Since the exploitation of mineral resources results in the release of radionuclides, and consuming radionuclides affects public health in the short and long term. A case study of the environmental radiation impact from coal mining and germanium processing was carried out in southwest China. The coal mines contain germanium and uranium and have been exploited for more than 40 years. The farmlands around the site of coal mining and germanium processing have been contaminated by the solid waste and mine water in some extend since then. Samples of crops have been collected from contaminated farmlands in research area. The research area covers a radius of 5 km, in which there are 2 coal mines located. 210Pb and 210Po have been analyzed as the key radionuclides during monitoring program. The average activity concentrations of 210Pb and 210Po in the crops were 1.38 and 1.32 Bq/kg in cereals, 4.07 and 2.19 Bq/kg in leafy vegetables and 1.63 and 1.32 Bq/kg in root vegetables. The annual effective doses due to the ingestion of 210Pb and 210Po in consumed crops have been estimated for adult residents living in research area. The average annual effective dose was 0.336mSv/a, while the minimum was 0.171 mSv/a and the maximum was 0.948 mSv/a. The results show that crops grown on contaminated farmland contained an enhanced level of radioactivity concentration. Ingestion doses of local residents in research area were significantly higher than the China average level of 0.112 mSv/a, and the world average level of 0.042 mSv/a through 210Pb and 210Po in crops intake respectively.

Several hypotheses have been presented on the origin of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) from its identification as the agent causing the current coronavirus disease 19 (COVID-19) pandemic. So far, no hypothesis has managed to identify the origin, and the issue has resurfaced. Here we have unfolded a pattern of distribution of several mutations in the SARS-CoV-2 proteins across different continents comprising 24 geo-locations. The results showed an evenly uneven distribution of unique protein variants, distinct mutations, unique frequency of common conserved residues, and mutational residues across the 24 geo-locations. Furthermore, ample mutations were identified in the evolutionarily conserved invariant regions in the SARS-CoV-2 proteins across almost all geo-locations we have considered. This pattern of mutations potentially breaches the law of evolutionary conserved functional units of the beta-coronavirus genus. These mutations may lead to several novel SARS-CoV-2 variants with a high degree of transmissibility and virulence. A thorough investigation on the origin and characteristics of SARS-CoV-2 needs to be conducted in the interest of science and to be prepared to meet the challenges of potential future pandemics.

One notable features of the SARS-CoV-2 genome is that the spike protein of SARS-CoV-2 has a functional polybasic (furin) cleavage site (RRAR) at the S1–S2 boundary through the insertion of 12 nucleotides encoding PRRA. To date, the furin cleavage site (FCS) remains an experimentally uncharted territory both structurally and functionally. For instance, whether or not FCS is actually cleaved, before or after viral cell entry or exit, still remains to be experimentally investigated. With currently available structural data, this article presents a computational structural characterization of the FCS inserted into SARS-CoV-2 spike glycoprotein, and puts forward a set of structural hypothesis against the hypothesis of SARS-CoV-2 from purposeful manipulation: (1), the inserted FCS does not alter, neither stabilize nor de-stabilize, the overall structure of SARS-CoV-2 spike glycoprotein; (2), the net structural consequence of FCS is the insertion of a furin cleavage site into SARS-CoV-2 spike glycoprotein, whose S1 and S2 subunits will still be bonded together even if the FCS is actually cleaved by furin protease.

Biomineralization has become a research hotspot and attracted widespread attention in the field of carbonate sedimentology. In this study, Bacillus licheniformis DB1-9 was used to induce the calcium carbonate precipitation at different magnesium calcium molar ratios in the laboratory to further explore the biomineralization mechanism. Phylogenetic tree shows that the bacteria belongs to Bacillus licheniformis species. The ammonia and carbonic anhydrase can be released by this bacteria, resulting in the pH increase, and the carbonic anhydrase can also promote the hydration reaction of carbon dioxide and subsequently produce the bicarbonate and carbonate ions to elevate the supersaturation of calcium carbonate in the liquid culture medium to facilitate the precipitation of carbonate minerals. The calcites have a shape of rhombohedron, dumbell, and elongation, and aragonite often appears in the form of mineral aggregates, besides that there are also the spherical and the fusiform minerals. FTIR result shows there are some organic functional groups, such as C-O-C and C=O, beside of the characteristic peaks of the calcite and the aragonite, indicating that microbial metabolism is closely related to the mineral formation. The superthin slices of the bacteria analyzed by HRTEM, SAED, EDS and STEM show that the surface and EPS can adsorb a large number of calcium ions and magnesium ions and EPS may act as the nucleation sites, what’s more, the intracellular nanometer-scale sphere areas show the amorphous structures, and the intracellular calcium ions and magnesium ions suggeste that they can be transported from the outside to inside the cell by diffusion along the concentration grade from high to low. This study may provide some references to further understand the biomineralization mechanism induced by microorganisms in the laboratory and the field, and also helps to explore the reason of the transition of calcite sea to aragonite sea in the geological history.

The spread of charging infrastructure (CIS) for battery electric vehicles is crucial for coping with the increasing number of electric vehicles. Therefore, the selection of ideal (fast-) charging locations determines acceptance, utilization and, thus, the economic viability of a single site or the whole charging network. The methodology of the Integrated Model Approach STELLA[1] for site identification of CIS uses proven methods of traffic modeling such as the classic four-step traffic modeling in a new context to enable statements regarding the positioning of CIS. Based on different spatial analyzes and characterizations of urban quarters, traffic generated by individuals is calculated using the FGSV approach of 2010. Because only (electric) motorized individual traffic is of importance for CIS, the share of trips is calculated by differentiating the modal split between various transport groups. One approach is to concretize the modal split share of public transport based on analyzes of different criteria and data sets, e.g. the accessibility of stops. The model approach STELLA, which also combines various extensive data (e.g. transport networks and traffic volumes, settlement structures, vehicle characteristics, power supply data and user requirements), is currently developed for a planning area covering the entire territory of the Federal Republic of Germany. [1] STELLA is the acronym for the German term "STandortfindungsmodell für ELektrische LAdeinfrastruktur”.

The economic development of the Yangtze River Delta region is in a stage of rapid growth. As a unique intersection of urban and rural functions, contradictions are prominent. The production, life, and ecological functions of suburban rural landscapes are forming a new trade-off and synergistic relationship. The planning policy of the Yangtze River Delta from 2021 to 2035 aims to achieve the coordinated development of ecology, economy, and people's lives in the suburban areas of the Yangtze River Delta. To evaluate the current status of the “production-living-ecological” functions of suburban rural areas in the Yangtze River Delta region and provide data support for future planning decisions in the Yangtze River Delta region, this study selected the suburban rural landscape of Jiashan as the research object and used temporal rank correlation analysis and spatial bivariate autocorrelation analysis to explore the evolution characteristics of the suburban rural landscape of Jiashan from 2000 to 2020. The results show that (1) the linear increase of the production function and life function of Jiashan rural areas has led to a decline in ecological functions, especially a decline in life functions. (2) There is a trade-off and synergistic relationship between the different functions of the suburban rural landscape of Jiashan, showing a temporal change pattern dominated by trade-offs. (3) The multifunctional trade-off and synergistic relationship of the suburban rural landscape in Jiashan County exhibited obvious spatial pattern variability, which was manifested as the evolution from street-centered areas to compatibility-trade-trade-off and from town-centered areas to compatibility-synergy-trade-off. The relevant policies for the construction of ecological green comprehensive demonstration areas affect the economic, social, and ecological development of the Yangtze River Delta region, resulting in substantial differences in the types and trends of the spatiotemporal evolution of the functional trade-off and synergistic relationship of suburban rural landscape. Targeted measures should be taken according to local conditions to guide the coordinated development of landscape functions.

Photonic circuits find applications in biomedicine, manufacturing, quantum computing and communications. Photonic waveguides are crucial components, typically having cross-sections orders of magnitude inferior compared with other photonic components (e. g. optical fibers, light sources and photodetectors). Several light coupling methods exist, consisting of either on-plane (e. g. adiabatic and end-fire coupling) or off-plane methods (e. g. grating and vertical couplers). The grating coupler is a versatile light transference technique which can be tested at wafer level, not requiring specific fiber terminations or additional optical components, like lenses, polarizers or prisms. This study focuses on fully-etched grating couplers without bottom reflector, made from hydrogenated amorphous silicon (a-Si:H), deposited over a silica substrate. Different coupler designs were tested, of these we highlight two: superimposition of two lithographic masks with different periods and an offset between them to create a random distribution and a technique based on the quadratic refractive index variation along the device’s length. Results were obtained by 2D-FDTD simulation. The designed grating couplers achieve coupling efficiencies for the TE-like mode over -8 dB (mask overlap) and -3 dB (quadratic variation), at a wavelength of 1550 nm. The coupling scheme considers a 220 nm a-Si:H waveguide and an SMF-28 optical fiber.

In the field of railroad safety, effective detection of surface cracks is critical, necessitating reliable, high-speed non-destructive testing (NDT) methods. This study introduces a hybrid Eddy Current Testing (ECT) probe, specifically engineered for railroad inspection, to address the common issue of ’lift-off noise’ due to varying distances between the probe and test material. Unlike traditional ECT methods, this probe integrates transmit and differential receiver coils, aiming to enhance detection sensitivity and minimize lift-off impact. The study optimizes ECT probes employing different driver coils, emphasizing three main objectives: a) quantitatively evaluating each probe using signal- to-noise ratio (SNR) and outlining a real-time data processing algorithm based on SNR methodology; b) exploring the frequency range proximal to the electrical resonance of the receiver coil; c) examining sensitivity variations across varying lift-off distances. The experimental outcomes indicate that the newly designed probe with figure 8-shape driver coil significantly improves sensitivity in detecting surface cracks on railroads. It achieves an impressive SNR exceeding 100 for defects with minimal dimensions of 1 mm in width and depth. Simulation results closely align with experimental findings, validating the investigation of optimal operational frequency and lift-off distance for selected probe performance, determined to be 0.3 MHz and 0.5 mm, respectively. The realization of this project would lead to notable advancements in enhancing railroad safety by improving crack detection efficiency.

The presence of escaped fish in aquaculture facilities as a result of harsh meteorological conditions (more pressing in a face of climate change) requires a better understanding of these dynamical behaviour through vigilant monitoring and validated numerical models. In this context, data from strain, stress sensors as well as meteorological and current sensors installed at an aquaculture farm in the Region of Murcia (Spain) were collected, processed and analysed. Among them, first results about the relationship between load and currents sensors are presented. Due to the complexity of the time series, various analyses were conducted to examine their interrelation, encompassing regression analysis of raw data and data segmented into different time intervals. Through this analysis, it was observed that employing distinct time windows better elucidated the data variability. Furthermore, an optimal data window of 240 data was identified, demonstrating significantly improved explanatory power, with the coefficient of determination (R2) increasing by approximately 0.8 depending on the section. This pave the way for optimizing the monitoring features that must be carried out to relate cause-and-effect variables in the behaviour of these off-shore infrastructures.

This article discusses the use of a hand held electronic nose to obtain information on the presence of some aromatic defects in natural cork stoppers, such as haloanisoles, alkylmethoxypyrazines and ketones. The proposed prototype has been developed as an instrumentation system with up to eight commercial gas sensors. Machine learning algorithms such as k-nearest neighbors and artificial neural networks has been used. The use of this system tries to improve the current aromatic defect detection process in the cork stopper industry, which is done by gas chromatography or human test panels.

This paper proposes a linear eddy-current feature to determine the radius of a metallic ball in a non-contact manner. An electromagnetic eddy-current sensor with two coils is placed co-axially to the metal ball during measurement. It is well known that the distance between the sensor and test piece (i.e. lift-off) affects eddy-current signals. In this paper, it is found that the peak frequency feature of inductance spectrum is linear to the lift-off spacing between the centre of coil and ball. Besides, the slope of peak frequencies versus lift-offs is linked to the radius of ball. The radius of metallic balls is retrieved from the experimental and embedded analytical result of the slope. Measurements have been carried out on 6 metallic balls with different radii. The radius of the metallic ball can be retrieved with an error of less than 2 %.

Understanding biological mechanisms that regulate emergence of viral diseases, in particular those events engaging cross-species pathogens spillover, are becoming increasingly important in Virology. Species barrier jumping has been extensively studied in animal viruses, and the critical role of a suitable intermediate host in animal viruses-generated human pandemics is highly topical. However, studies on host jumping involving plant viruses have been focused on shifting intra-species, leaving aside the putative role of “bridge hosts” in facilitating interspecies crossing. Here, we take advantage of several VPg mutants, derived from a chimeric construct of the potyvirus Plum pox virus (PPV), analysing its differential behaviour in three herbaceous species. Our results showed that two VPg mutations in a Nicotiana clevelandii-adapted virus, emerged during adaptation to the bridge-host Arabidopsis thaliana, drastically prompted partial adaptation to Chenopodium foetidum. Although, both changes are expected to facilitate productive interactions with eIF(iso)4E, polymorphims detected in PPV VPg and the three eIF(iso)4E studied, extrapolated to a recent VPg:eIF4E structural model, suggested that two adaptation ways can be operating. Remarkably, we found that VPg mutations driving host-range expansion in two non-related species, not only are not associated with cost trade-off constraints in the original host, but also improve fitness on it.

Mid-tropospheric cut-off low (COL) pressure systems are linked to severe weather, heavy rainfall and extreme cold conditions over South Africa. They often result in floods and snowfalls in winter disrupting economic activities. This paper examines the evolution and circulation patterns associated with severe COLs over South Africa. We evaluate the performance of the 4.4 km Unified Model (UM) which is currently used operationally by the South African Weather Service to simulate daily rainfall. Circulation variables and precipitation simulated by the UM were compared against ECMWF’s ERA Interim reanalyses and GPM precipitation at 24-hour timesteps. We present five recent (2016-2019) severe COLs that had high impact and found higher model skill when simulating heavy precipitation during the initial stages than the dissipating stages of the systems. A key finding was that the UM underestimated precipitation mainly due to inaccurate placing of COL centers and areas of heavy rainfall by up to 5° of latitude away from the actual location, due to the poor formulating of cumulus and microphysics schemes in the model. Understanding the performance and limitations of the UM model in simulating COL characteristics can benefit severe weather forecasting and contribute to disaster risk reduction in South Africa.

This work proposes a novel methodology for the complete characterization of fiber reinforced concrete (FRC). The method includes bending tests of prismatic notched specimens, based on the Standards for FRC, tensile and pure shear tests. The values adopted by the standards for designing FRC are the obtained from bending tests, typically fR3, even for shear and pure tension loading. This paper shows that the remaining strength of FRC, supplied by the fibers, depends on the type of loading. In the case of shear and tensile loading the prescriptions of the standards may be unsafe. In this work, the remaining halves of specimens subjected to bending test are prepared and used for shear and tension tests. This means significant savings in specimen preparation and a greater amount of information for structural use of FRC. The results provide relevant information for the design of structural elements of FRC compared with the only use of data supplied by bending tests. In addition, a video-extensometry system was used to analyze the crack generation and cracking patterns. The video-extensometry applied to shear tests allowed the assessment of the sliding values and crack opening values at the crack discontinuity. These values may be quite relevant for the study of the FRC behavior when subjected to shear according to the shear-friction model theories.

There have been several cases of large-scale wind generators (WGs) tripping off caused by untimely fault removing in recent years. Currently, the discoordination between the box-type transformer fuse protection (BTFP) and two-section collecting line current protection (CLCP) brings a security risk to wind farm. In order to ensure the selectivity, the first section (Sec-I) CLCP should be set a enough interval that is longer than the fuse melting time, and another interval is set for the Sec-II CLCP, which weakens the speed of the CLCP. When a fault occurs on the collecting line, there is no doubt that WGs cannot work too long in abnormal operation, which may cause WGs to be placed off the grid. For a power system with high penetration of wind power, large-scale WGs tripping off will cause a great power shortage, and affect the stability of the power system. The selectivity and sensitivity of the CLCP is analyzed in detail to make the CLCP speed better. Considering the fault ride-through ability of WGs, the fault clear time is an important factor to lead to large-scale WGs tripping off. Two main works are done in this paper. The first is to accelerate the speed of the Sec-I CLCP though reducing the protection zone. Another one is introduce the risk assessment module into the CLCP, which not only improve the speed of the CLCP but also ensure the safety of the wind farm during faults. According to the deference in trip-off causes of WGs, the matching functions are created to assess the trip-off risk of WGs on the spot. In the case of fault, the trip-off risk indicators of WGs are timely updated to data sharing center and open to the CLCPs. The set of risk indicators is divided into several subsets according to the risk range. The dynamic changes of the subsets during fault help to improved CLCP scheme. This scheme can accelerate protection speed based on the increasing risk of large-scale WGs tripping off in wind farms. Compared with traditional CLCP, this approach can make the CLCP combines selectivity and speed better based on the analysis of the ride- through ability of WGs.

Cementitious materials exhibit excellent binding properties and micropore structures that support the stabilization of TiO2 nanoparticles within the matrix. Therefore, these materials are ideal for the development of functional construction products with TiO2 nanoparticles. This study investigated the degree of hydration, microstructure, and mechanical properties of cement-containing TiO2 nanoparticles. The experimental results demonstrated that TiO2 nanoparticles accelerated the hydration rate of cement, reducing the setting times. Moreover, TiO2 nanoparticles changed matrix microstructure, decreasing the porosity and improving early-age strength. Although TiO2 nanoparticles function as nucleation sites in the cement hydration reaction, the tendency of the particles to clump implies that proper dispersion should be ensured when mixing in large quantities. When developing new building materials incorporating TiO2 nanoparticles, considering the effect of TiO2 nanoparticles on the hydration reaction of cementitious materials is crucial.

The social recognition of cultural landscapes has increased in recent years. Culture must be accessible to all citizens, helping them to interpret the cultural landscape in the most respectful and autonomous way possible. Nevertheless, the link between accessibility and heritage requires a sensitive perception of the environment and individuals in their different situations. Usually, however, only partial solutions are offered, whereas a global, truly sustainable and inclusive approach should be adopted. In this sense, information design can play an essential role in the enjoyment and knowledge of Heritage Landscapes. The aim of this article is to present some reflections on this topic, which have led a group of teachers and students from the Laboratory of Architectural, Cultural and Heritage Landscape of the University of Valladolid (LAB/PAP) to develop experimental design proposals for the archaeological site of Tiermes, in Soria, Spain. The method applied is based on field research, case studies, project proposals, workshops and user testing. The resulting proposals emerge from the previous research developed by the LAB/PAP. They will focus on information design to present this extraordinary site in an inclusive way. The final discussion will decide which of these proposals will be easier and more useful to implement.

The superfamily of Acid proteases has two catalytic aspartates for proteolysis of their peptide substrates. Here, we show a minimal structural scaffold, the Structural Catalytic Core (SCC), which packs all conserved substructure elements around the catalytic machinery, and which can be found in all enzymes of the Acid proteases superfamily. The SCC is a dimer of several structural blocks, such as the DD-link, the D-loop and the G-loop, around two catalytic aspartates in each protease subunit or within an individual chain. The dimer of two D-loop/DD-link substructures makes a DD-zone, and the dimer of two D-loop/G-loop substructures makes a psi-loop. These structural markers are useful for protein comparison, structure identification, protein family separation and protein engineering.

The morphological aspects of urban growth on wetlands in Africa are under-researched. Using the Densu Delta Ramsar site in Accra, Ghana, as a case study, this paper analyses the morphological patterns and drivers of urban growth and its impact on wetlands. Data were obtained through remote-sensing, ground truthing and limited key informant interviews. The analysis combined land use/land cover, building coverage and multiple regression techniques, with the aid of GIS and STATA software. The findings reveal that urban growth at the Ramsar site follows discernible spatial patterns consistent with the spreading pancake, village magnet and ribbon development models. However, the primary force behind these patterns is growing demand for land to meet housing needs, aided by the failure of state institutions to perform their land use control and wetland protection functions. To achieve sustainable urban development, there is an urgent need to ensure effective wetland management by enforcing existing land use, development control and wetland protection measures. This calls for the strengthening, resourcing and closer collaboration between the various state agencies responsible for urban planning and wetland management. There is also the need to engage and sensitise political leaders to increase their commitment to implementing wetland protection and pro-environmental policies.

Evidence regarding the role of oral antibiotics (oA) alone or combined with mechanical bowel preparation (MoABP) for elective colorectal surgery remains controversial. A prospective database of 8,359 colorectal resections gathered over a 32-month period in 78 Italian surgical units (the iCral 2 and 3 studies), reporting patient-, disease-, and procedure-related variables together with 60-day adverse events, was re-analyzed to identify a subgroup of 1,013 cases (12.1%) that received either oA or MoABP. This dataset was analyzed using a 1:1 propensity score-matching model including 20 covariates. Two well-balanced groups of 243 patients each were obtained: group A (oA), and group B (MoABP). The primary endpoints were anastomotic leakage (AL) and surgical site infections (SSIs) rates. Group A vs. group B showed a significantly higher AL risk [14 (5.8%) vs 6 (2.5%) events; OR 3.77; 95%CI 1.22-11.67; p = .021], while no significant difference was recorded between the two groups regarding SSIs. These results strongly support the use of MoABP for elective colorectal resections.

Small island developing states (SIDS) traditionally face a set of challenges like the narrow economic structure, environmental issues, and dependence on a few ranges of economic activities forcing them to open the economy to the exterior. Therefore, their development model, like in Cape Verde depends on migration, remittances, dependence on aid, tourism, and state employment. The current research offers an insight about the nature of Cape Verde’s economy as a SIDS and the degree to which its economy depends on tourism and government services, both of which are supported through aid programs. Understanding Cape Verde’s development model is important to clarify the challenges the country faces, and its development needs to gather a long-term resilience and to understand if it is changing from a MIRAB (Migrations, Remittances, Aid and Bureaucracy) model into another one.

Abstract: CRISPR/Cas systems are used for genome editing, both in basic science and in bio-technology. At the same time, CRISPR/Cas editors have several limitations, including insufficient specificity leading to "off-targets" and the dependence of activity on chromatin state. A number of highly specific Cas9 variants have been obtained now, but most of them are characterized by reduced activity on eukaryotic chromatin. We identified a spatial cluster of amino acid residues in the PAM-recognizing domain of Streptococcus pyogenes Cas9, whose mutations restore the activity of one of the highly specific forms of SpyCas9 without reducing its activity in Saccharomyces cere-visiae. In addition, one of these new mutations also increases the efficiency of SpyCas9-mediated editing of a site localized on the stable nucleosome. The improved Cas9 variants we obtained, which are capable of editing hard-to-reach regions of the yeast genome, may help in both basic research and yeast biotechnological applications.

The environmental legacy of post-closure mine sites poses a significant risk to the sustainability of mining operations and natural resource development. This study aims to advance the understanding of sustainable mine site reclamation behavior in Canada by using multi-temporal Landsat satellite images to examine the long-term land cover changes at post-closure mine sites. Six representative post-closure mine sites were selected for the evaluation and comparison. The Normalized Difference Vegetation Index (NDVI) analysis, Landsat image classification, post-classification change detection, and Regrowth Index (RI) analysis were conducted to assess the speed and extent of landscape and vegetation recovery at the target mine sites. A significant vegetation recovery was quantified for the mine sites that have experienced active reclamation activities. In contrast, the post-closure mine area undergoing only the passive revegetation typically demonstrated a slow and minor increase in vegetation over time. The actively revegetated mine sites can typically be restored to a level that equals or better than the pre-mining situation. This work confirms that active reclamation and revegetation at post-closure mine sites is critically important in sustainable mining. The quantified mine site reclamation behavior and the relevant sustainable practices would be useful for evidence-based sustainable resource management in Canada.

Cytosine (C) to uracil (U) RNA editing is one of the most important post-transcriptional processes, however exploring C-to-U editing events efficiently within the crop mitochondrial genome remains a challenge. An improving predictive RNA editor for crop mitochondrial genomes, iPReditor-CMG, was proposed, which was based on SVM, three common crop mitochondrial genomes and self-sequenced tobacco mitochondrial ATPase. After multi-combination feature extracting, high-dimension feature screening and multi-test independent predicting, the results showed that the average accuracy of intraspecific prediction was 0.85, and the highest value even up to 0.91, which outperformed the previous reference models. While the prediction accuracies were 0.78 between dicotyledons and no more than 0.56 between dicotyledons and monocotyledons, implying a possible similarity in C-to-U editing mechanisms among close relatives. The best model was finally identified with an independent test accuracy of 0.91 and an area under the curve of 0.88, and further suggested that five unreported feature sequences TGACA, ACAAC, GTAGA, CCGTT and TAACA were closely associated with the editing phenomenon. Multiple evaluation findings supported that the iPReditor-CMG could be effectively applied to predict crop mitochondrial editing sites, which may contribute to insight into their recognition mechanisms and even other post-transcriptional events in crop mitochondria.

At the molecular level, response to an external factor or an internal condition causes reprogramming of temporal and spatial transcription. When an organism undergoes physiological and/or morphological changes, several signaling pathways are activated simultaneously. Examples of such complex reactions are the response to temperature changes, dehydration, various biologically active substances, and others. Synergistic action of multiple pathways greatly complicates the experimental study of the molecular genetic mechanisms of the organism's reactions. As a result, a significant part of the regulatory ensemble in such complex reactions remains unidentified. We developed metaRE, an R package for the systematic search for cis-regulatory elements enriched in the promoters of the genes significantly changed their transcription in a complex reaction. metaRE mines multiple expression profiling datasets generated to test the same organism's response and identifies simple and composite cis-regulatory elements systematically associated with differential expression of genes. Here we showed metaRE performance for identification of cold stress-responsive cis-regulatory code in Arabidopsis thaliana. MetaRE identified potential binding sites for known as well as unknown cold response regulators. Software with source files, documentation, and example data files are freely available online at the repository (https://github.com/cheburechko/MetaRE).

The study was conducted in coniferous and deciduous old growth forests in two forest complexes located in: i) the fenced area of the Popielno Research Station of the Polish Academy of Sciences, with free-living Polish pony [Polish primitive horse (Equus ferus caballus)], and ii) open Maskulińskie Forest District managed (harvested) forest, without horses. The impact of forest animals on ground cover layer as well as on understory shrub layer and undergrowth, in i) area (horses and other forest animals) was compared with the results in ii) area (forest animals without horses). Very significant differences in the understory and undergrowth (above 0,5 m) layer vegetation communities structure between both areas and type of stands were found. The results suggest that the presence of the Polish horse substantially changed the species composition and increased the species diversity of the ground layer and shrub layer both on coniferous forest and in the deciduous forest habitats. The height of the shrub layer trees was lower by 30% in the area with the Polish horse.

When we are asleep we lose the ability to promptly respond to external stimuli and yet we spend many hours every day in this inherently risky behavioral state. This simple fact strongly suggests that sleep must serve essential functions that rely on the brain going offline, on a daily basis, and for long periods of time. If these functions did not require partial sensory disconnection, it would be difficult to explain why they are not performed during waking. Paradoxically, despite its central role in defining sleep and what sleep does, sensory disconnection during sleep remains a mystery. We have a limited understanding of how it is implemented along the sensory pathways, we do not know whether the same mechanisms apply to all sensory modalities, nor do we know to which extent these mechanisms are shared between non-rapid eye movement (NREM) sleep and REM sleep. The main goal of this contribution is to review some knowns and unknowns about sensory disconnection during sleep as a first step to fill this gap.

The evolutionary theory of aging, particularly antagonistic pleiotropy (AP), provides an account of the ultimate origins of aging. What remains unclear is the nature of the proximate mechanisms by which AP gives rise to diseases of aging, like cardiovascular disease and Alzheimer’s disease. Damage-centric theories focusing on loss of genetic and cellular function have been proposed, as well as programmatic theories focusing on unwanted gene and cellular function. The latter include the hyperfunction and developmental theory that view aging as the futile continuation, or run-on, of growth and developmental programmes into later life. Yet neither type of theory has performed well in explaining late-life disease aetiology, particularly with respect to disease onset, presentation and progression. What is proposed here in this review is a new programmatic theory of aging. We argue that the emergence of many specific diseases may involve quasi-programmes that are not the result of run-on, but rather are triggered by other factors in late life. Such triggers may be non-programmatic (e.g. infection, mechanical injury) or programmatic. Moreover, the consequent pre-pathological and pathological changes may in some cases trigger further changes, leading to futile and destructive cascades of quasi-programmes and pathology. The origins of triggered quasi-programmes can be traced to biological constraint i.e. the inability of organisms to optimise all functions at once. And, to some extent, the new theory presented here revises the understanding of AP. That is, because any gene can be triggered in an erroneous manner, every gene is potentially an AP gene that risks pathology, though level of risk varies according to constraint. To help validate the theory, we test it against several complex diseases of aging. The new model in this review attempts to provide a blueprint understanding that, to a certain extent, closes the gap in the causal chain of events between evolutionary causes of aging and the aetiology of age-related diseases. It also helps to explain why certain disorders mimic accelerated aging and how interventions, such as the suppression of IIS and mTOR retard many aspects of aging; notably, though, unlike prior programmatic theories, the new theory is not mTOR-centric. Finally, it provides new perspectives on possible treatment of aging.

Integrating numerous renewable resources has been extensively researched and studied to create a dependable energy system. This study investigated the best techno-economical hybrid energy system configuration while using hydrogen energy to keep the system's energy balanced. Additionally, this study aims to determine the best hybrid system configuration for the location under investigation. A novel technique of DBM (Deterministic Balanced Method) was introduced to determine the total annual energy output for the project's lifetime. This approach is used to contrast the outcomes of other HOMER software tools. Then, using HOMER, it is possible to confirm the sizing optimization results for the suggested method by comparing the power ratings and yearly energy output. A detailed comparison between our proposed method and HOMER Pro has been conducted for validation and verification. Our method has been rigorously tested in various hybrid off-grid energy systems, ensuring its applicability and reliability across different scenarios and configurations. The results of our study indicate a high degree of similarity between the proposed approach and HOMER pro for computing annual energy power for the studied energy systems. Specifically, our analysis revealed that the difference between the approaches was within a range of 5%, indicating a high level of consistency and reliability in our method. These findings suggest that our approach can be confidently applied to determine the appropriate size of hybrid energy systems accurately. Overall, our study provides valuable insights into the development of effective sizing methodologies for hybrid energy systems. After considering the amount of solar radiation and wind speed gathered by global weather data platforms like NASA and METEONORM, this paper has also included a real case study of the Cairo International Airport's hybrid renewable energy production systems. To guarantee the viability of this study, the system design was founded on an actual load that was researched and simulated. A cluster of distributed networks was finally proposed to use the excess energy and enable energy conversion processes to be used in industry and transportation applications.

The human immunodeficiency virus 1 (HIV-1) viral protease (PR) is one of the most studied viral enzymes, and approval of drugs targeting its catalytic activity opened the door to the develop-ment of highly active antiretroviral therapy (HAART). Despite the fact that its crucial role in viri-on maturation is well characterized, an increasing body of research is starting to focus on its abil-ity to cleave host cell proteins, based on recent advances in proteomics and genomics technologies. Such findings are apparently in contrast with the dogma of HIV-1 PR activity being restricted to the interior of nascent virions, and suggest catalytic activity within the host cell environment. Given the limited amount of PR present in the virion at the time of infection, it is tempting to specu-late that such events mainly occur during viral late gene expression, mediated by newly synthe-sized Gag-Pol polyprotein precursors, rather than at a very early stage of infection, before pro-viral integration. Among cellular targets of HIV-1 PR, three major clusters can be identified: pro-teins involved in viral and cellular translation, those controlling cell survival, and restriction fac-tors responsible for innate/intrinsic antiviral responses. Indeed, by cleaving host cell translation initiation factors HIV-1 PR can impair cap-dependent translation, thus promoting IRES-mediated translation of late viral transcripts and viral production, while by targeting several apoptotic fac-tors it modulates cell survival, thus promoting immune evasion and viral dissemination. Addi-tionally, HIV-1 PR counteracts restriction factors incorporated in the virion that would otherwise interfere with nascent virus vitality. Thus, HIV-1 PR appears to modulate host cell function at dif-ferent times and locations during its life cycle, to ensure efficient viral persistency and propaga-tion. This kind of PR-mediated host cell modulation is found in a plethora of different viruses and HIV-1 is no exception, and although we are far from having a complete picture, it is clear that the PR has a multifaceted role in interfering with host machineries to better suit viral replication, and is a field that needs to be explored further.

Two-wheeler vehicles are the most significant mode of transportation for Kenyans in both rural and urban regions thereby contributing to local air pollution, and greenhouse gas emissions (GHG). The transition to electric two-wheeler vehicles can make a significant contribution to reducing GHG and improving the socio-economic lives of people living in rural Kenya. Re-newable energy systems can considerably contribute to the charging of electric two-wheeled vehicles, thus leading to the reduction of carbon emissions and the expansion of renewable energy penetration in rural Kenya. Therefore, this paper focuses on integrating and modelling electric two-wheeled vehicles (e-bikes) into an off-grid photovoltaic Water-Energy Hub located in the Lake Victoria Region of Western Kenya using the Conventional and Renewable Energy Opti-mization (CARNOT) Toolbox in MATLAB / Simulink. Electricity demand data obtained from the Water-Energy Hub was investigated and analysed. Potential solar energy surplus was identified and electric two-wheeler vehicles were integrated based on the surplus. A field measurement investigation on the energy consumption of the electric two-wheeler vehicles based on the rider’s driving behaviour was also carried. The annual electricity demand of 27,267 kWh, photovoltaic (PV) electricity production of 37,785 kWh with an electricity deficit of 370 kWh were obtained from the simulation results. To reduce the electricity deficit, a load optimisation algorithm was de-veloped to optimally integrate the electric 2-wheeler vehicle into the Water-Energy Hub. It was found that using the load optimisation algorithm, the annual electricity deficit was reduced to 1 kWh and the annual electricity demand was increased by 11% (30,767 kWh) which is enough to charge 4 additional electric two-wheeler batteries daily.

Defect detection in ferromagnetic substrates is often hampered by non-magnetic coating thickness variation when using conventional eddy current testing technique. The lift-off distance between the sample and the sensor is one of the main obstacles for the thickness measurement of non-magnetic coatings on ferromagnetic substrates when using the eddy current testing technique. Based on the eddy current thin-skin effect and the lift-off insensitive inductance (LII), a simplified iterative algorithm is proposed for reducing the lift-off variation effect using a multi-frequency sensor. Compared to the previous techniques on compensating the lift-off error (e.g., the lift-off point of intersection) while retrieving the thickness, the simplified inductance algorithms avoid the computation burden of integration, which are used as embedded algorithms for the online retrieval of lift-offs via each frequency channel. The LII is determined by the dimension and geometry of the sensor, thus eliminating the need for empirical calibration. The method is validated by means of experimental measurements of the inductance of coatings with different materials and thicknesses on ferrous substrates (dual-phase alloy). The error of the calculated coating thickness has been controlled to within 3 % for an extended lift-off range of up to 10 mm.

The objective of this paper was to give an overview of the expressed preference (EP) techniques of environmental valuation. These methods offer estimation of the value of a resource not necessarily willingness to pay (WTP) or willingness to Accept (WTA) compensation rather upper and lower values. The method of measuring individuals’ willingness to pay is usually based on contingent valuation method (CVM). This research focuses on defining, categorizing, and applicability of various environmental valuation techniques that have been and can be applied in attaching value to a given resource using expressed/Revealed preference methods. The study serves as a supplementary synthesis and discussion to the board of knowledge of resource valuation methods. More specifically, selected methods to discussed herein include; contingent valuation method, hedonic pricing model, travel cost method, trade-off game method, the costless-choice method, Delphi method, Replacement Cost Method, Relocation Cost Method, Opportunity cost method, and Cost-benefit Method. In the last part, applicability of the methods is fully illustrated to support future studies on resource valuation.

There is scientific consensus that organismal aging did not evolve by natural selection (NS) because it lacks individual benefit. Nonetheless it exists, leading to much speculation about its origins, and when the diminishing force of selection begins. Both concepts are based upon two misconceptions; that aging occurs in and of itself and is caused by the declining strength of NS during the reproductive lifespan. Although lacking individual benefit, aging evolved by NS as a tradeoff of survival for reproduction. Based upon regulatory dynamics that participate in this tradeoff, aging begins once reproductive success has been achieved through offspring nurturing. Thereafter, the strength of NS wanes to exponentially accelerate aging, leading to death. Assumptions of the theory are that: (1) a life-long, “holistic” regulatory mechanism whose genic expression is modified epigenetically, originates in ontogenesis; (2) the regulatory mechanism of the last developmental stage becomes redundantly expressed during “morphostasis”, a non-aging, life interval of peak vitality to ensure completion of reproduction through nurturing, and (3) thereafter, loss of regulatory redundancy causes aging which reduces the strength of natural selection and allows accumulation of randomly occurring somatic damage.

Balsam fir trees are a specialty agricultural species that are largely used as Christmas trees. Soil or tissue sampling is seldom performed to assess balsam fir nutrition needs, which can contribute to over or under fertilization and subsequent environmental challenges. Remote sensing to determine the normalized difference vegetation index (NDVI) has had strong relationships with nutrition in other plants. This research aimed to determine whether there is a relationship between NDVI and nutrition in balsam fir. A random sample of 45 trees was selected in autumn of 2021 and then another 70 trees selected in spring of 2022. Soil and needle tissue samples were analyzed for N, P, K, Ca, Mg, S, Fe, Zn, Mn, B, and Cu. An uncrewed aerial vehicle equipped with a multispectral camera was flown over the orchard to determine the NDVI for each tree. Nutrition and NDVI were analyzed for correlations through all sampled trees. Separate correlation analyses were repeated for mature trees (greater than 5 years old) and young trees (less than 5 years old). Soil nutrients N, P, K had a significant relationship with NDVI in autumn sampling. Only N was correlated consistently in both autumn and spring, with R2 of 37% and 33% respectively. Relationships were much stronger when only mature trees were considered, increasing to 60% and 51% respectively. NDVI was found to offer predictive power for tissue N that can be useful to producers to help optimize fertilizer input. However, further work is needed to refine these relationships.

Soil, geochemical, microbiological and archaeological studies were conducted at eight settlements dating from the Paleolithic to Late Medieval and New Times near the Southern Trans-Urals mountains, Russia. The forest-steppe landscapes, rivers and abundance of mineral resources have attracted people to region since ancient times. Properties of cultural layer (CLs): close to neutral pH, well structured, absence of salinity, enrichment with exchangeable calcium and anthropogenic phosphorus (0.2–0.4%). The majority of CLs start from 3–25 cm and last up to 40–60 cm and contain 6–10% organic carbon (Corg), in a layer of 0–20 cm because modern processes are developing here, at Ishkulovo site (around 14th century) Corg decreases to 1.3%, because CL is below 80 cm and in the absence of fresh organic material it is mineralized. The content of microbial biomass of the 0–10 cm layer is 520–680 μg С/g of soil, microbes cause the emission of 0.2–1.0 μg C–CO2/g soil per h. The proximity of the studied sites to deposits of copper, chromium, zinc, manganese and Magnitogorsk Metallurgical and Uchaly processing plants creates geochemical anomalies of soils. Pollutants are also released into the CLs from bronze products, ore, ceramic fragments and raw materials from their manufacture. It leads to the concentration of pollutants of the 1st (arsenic, lead, zinc) and 2nd (cobalt, copper, nickel, chromium) hazard classes in the studied CLs, often in quantities higher than the clarke and less often – more than the allowable content for human health.

Interactions between proteins and ions are essential for various biological functions like structural stability, metabolism, and signal transport. Given that more than half of all proteins bind to ions, it becomes crucial to identify ion-binding sites. Accurate identification of protein-ion binding sites helps us to understand proteins’ biological functions and plays a significant role in drug discovery. While several computational approaches have been proposed, this remains a challenging problem due to the small size and high versatility of metals and acid radicals. In this study, we propose IonPred, a sequence-based approach that employs ELECTRA (Efficiently Learning an Encoder that Classifies Token Replacements Accurately) to predict ion binding sites using only raw protein sequences. We successfully fine-tuned our pretrained model to predict the binding sites for nine metal ions (Zn2+, Cu2+, Fe2+, Fe3+, Ca2+, Mg2+, Mn2+, Na+, and K+) and four acid radical ion ligands (CO32−, SO42−, PO43−, NO2−). IonPred surpassed six current state-of-the-art tools by over 44.65% and 28.46% respectively in F1 score and MCC when compared on an independent test dataset. Our method is more computationally efficient than existing tools producing prediction results for a hundred sequences for a specific ion in under ten minutes.

Plasminogen (Plg) is the inactive form of plasmin (Plm) that exists in two major glycoforms, referred to as glycoforms I and II (GI and GII). In the circulation, Plg assumes an activation-resistant 'closed' conformation via interdomain interactions and is mediated by the lysine binding site (LBS) on the kringle (KR) domains. These inter-domain interactions can be readily disrupted when Plg binds to lysine/arginine residues on protein targets or free L-lysine and analogues. This causes Plg to convert into an 'open' form which is crucial for activation by host activators. In this study, we investigated how various ligands affect the kinetics of Plg conformational change using small-angle X-ray scattering (SAXS). We began by examining the open and closed conformations of Plg using size-exclusion chromatography (SEC) coupled with SAXS. Next, we developed a high throughput (HTP) 96-well SAXS assay setup. This method enables us to determine the Kopen value, which is used to compare ligands’ effect on Plg conformation directly. Based on our analysis using Plg GII, we have found that the Kopen for ε-aminocaproic acid (EACA) is approximately three times greater than that of Tranexamic acid (TXA), which is widely recognized as a highly effective ligand. We demonstrated further that Plg undergoes a conformational change when it binds to the C-terminal peptides of the inhibitor α2-antiplasmin and receptor Plg‑RKT. Our findings suggest that, besides the C-terminal lysine, internal lysine(s) are also necessary for the formation of open Plg. Finally, we compared the conformational changes of Plg GI and GII directly and found that the closed form of GI, which has an N-linked glycosylation, is less stable. To summarize, we have successfully determined the response of Plg to various ligand/receptor peptides by directly measuring the kinetics of its conformational changes.

The purpose of this study was to clarify the attachment types of the tibialis anterior tendon (TAT) in Japanese fixed cadavers and to determine the attachment site area in three dimensions. We examined 100 feet from 50 Japanese cadavers. The TAT was classified according to differences in the number of fiber bundles as: Type I, with one fiber bundle; Type II, with two fiber bundles; and Type III, with three fiber bundles. The attachment site area of the TAT was measured using a three-dimensional scanner. Cases were Type II in 95% and Type III in 5%, with no cases of Type I identified. In Type II, mean attachment site areas were 85.2 ± 18.2 mm2 for the medial cuneiform bone (MCB) and 72.4 ± 19.0 mm2 for the first metatarsal bone (1MB), showing a significantly larger area for MCB than for 1MB. These findings suggest the possibility of ethnic differences in TAT attachment types and suggest that TAT attachments in Japanese individuals are highly likely to be Type II, with rare cases of Type III. Accurate measurement of attachment site areas is possible with appropriate three-dimensional measurements.

Long-term, multi-decade research on planted tree survival in urban settings is sparse. One understudied urban environment is highway rights-of-way (ROW), lands adjacent to high-speed, unsignalized roadways. We conducted a re-inventory of tree planting cohort in northern Illinois, U.S. on a 48 km-long highway near Chicago which were 10-, 21-, and 30-years old to evaluate long-term patterns of survival and diversity. Using each randomly selected planting site along the highway as a unit of observation and analysis, we compared the number of trees documented in record drawing to the number of trees currently alive to determine percent survival. We evaluated 224 planting sites which originally contained 2,944 trees and collected data about the planting site location. For the oldest cohort, 26% of trees were still alive in 2018 (median survival by species = 16%, Q1 = 0%, Q3 = 48%), while 31% of the 21-year-old cohort (med. = 6%, Q1 = 0%, Q3 = 47%) and 86% of the 10-year-old cohort were still alive (med. = 85%, Q1 = 74%, Q3 = 96%). The survival of the 21- and 30-year-old cohort matches urban tree survival estimates by other researchers, while the 10-year-old survival is higher than expected. The only planting location characteristic that significantly affected survival was traffic islands (areas between the highway and entrance/exit ramps). Species with low drought tolerance were less likely to be alive for the 10-year-old cohort. Waterlogging tolerant species were more likely to be alive in the 10-year-old cohort. Since some species in the 21- and 30-year-old cohorts had very low survival, the tree species richness and diversity s in study areas declined between the initial record drawings and reinventory. This study demonstrates the challenges of maintaining long-term survival and diversity in the highway ROW and emphasizes the importance of species selection.

Infection with Zika virus (ZIKV), a member of the Flavivirus genus of the Flaviviridae family, typically results in mild self-limited illness, but severe neurological disease occurs in a limited subset of patients. In contrast, serious outcomes commonly occur in pregnancy that affect the developing fetus, including microcephaly and other major birth defects. The genetic similarity of ZIKV to other widespread flaviviruses, such as dengue virus (DENV), presents a challenge to the development of specific ZIKV diagnostic assays. Nonstructural protein 1 (NS1) is established for use in immunodiagnostic assays for flaviviruses. To address the cross-reactivity of ZIKV NS1 with proteins from other flaviviruses we used site-directed mutagenesis to modified putative epitopes. Goat polyclonal antibodies to variant ZIKV NS1 were affinity-purified to remove antibodies binding to the closely related NS1 protein of DENV. An antigen-capture ELISA configured with the affinity-purified polyclonal antibody showed a linear dynamic range between approximately 500 to 30 ng/mL, with a limit of detection of between 1.95 and 7.8 ng/mL. NS1 proteins from DENV, yellow fever virus, St. Louis encephalitis virus and West Nile virus showed significantly reduced reactivity in the ZIKV antigen-capture ELISA. Refinement of approaches similar to those employed here could lead to development of ZIKV-specific immunoassays suitable for use in areas where infections with related flaviviruses are common.

The investigation of membrane proteins, key constituents of cells, is hampered by the difficulty and complexity of their in vitro synthesis, of unpredictable yield. Cell-free synthesis is herein employed to unravel the impact of the expression construct on gene transcription and translation, without the complex regulatory mechanisms of cellular systems. Through the systematic design of plasmids in the immediacy of the start of the target gene, it was possible to identify translation initiation and the conformation of mRNA as the main factors governing the cell-free expression efficiency of the human voltage dependent anion channel (VDAC), a relevant membrane protein in drug-based therapy. A simple translation initiation model was developed to quantitatively assess the expression potential for the designed constructs. A scoring function is proposed that quantifies the feasibility of formation of the translation initiation complex through the ribosome-mRNA hybridization energy and the accessibility of the mRNA segment binding to the ribosome. The scoring function enables to optimize plasmid sequences and semi-quantitatively predict protein expression efficiencies. This scoring function is publicly available as webservice XenoExpressO at rna.tbi.univie.ac.at.

Oaks are a dominant and key tree species in Mediterranean forest ecosystems. However, in recent decades, oak forests have been heavily impacted by oak decline, a worldwide phenomenon exacerbated by climate change. The charcoal disease agent Biscogniauxia mediterranea is involved in the decline of Mediterranean oak formations in a variety of contexts. Here, we investigated the impact and role of B. mediterranea in decline of oaks in Castelfidardo Forest, a relict wood of the late Holocene and a Site of Community Importance. We established five plots within which we recorded the tree positions, any symptoms and signs of decline, association of B. mediterranea to declining trees, and the deadwood and associated mycota. Of 471 oaks inspected, 7.0% showed brownish exudates on the stems, 46.9% showed epicormic shoots along the main trunk, and 24.4% showed black carbonaceous stromata on diseased branches and trunks. The decline was most severe for Quercus cerris, which comprised plots #4 and #5, at 50.0% (81/162 trees) and 29.0% (33/114), respectively; then for Quercus robur for plot #3, at 40.0% (38/95); and finally for Quercus pubescens for plots #1 and #2, at 13.7% (7/51) and 12.3% (6/49), respectively. Bark tissue was collected from trees with charcoal cankers, with microscopy examination and identification by mycological and molecular methods. This investigation revealed close association between oaks with pronounced reduction of vitality and incidence of B. mediterranea. The deadwood was equally distributed among the five plots, and was heavily colonized by Basidiomycota. The high incidence of this oak-weakening pathogen B. mediterranea appears to be related to stress conditions (e.g., water scarcity, prolonged drought). However, absence of silvicultural management, high competition among physiologically mature trees, and the geographic isolation of this residual forest might have predisposed these oaks to decline.

Various peptides or non-structural amino acids are recognized by their specific target proteins and perform biological role in various pathways in vivo. Understanding the interactions between target protein and peptides (or non-structural amino acids) provides key information on the molecular interactions, which can be potentially translated to the development of novel drugs. However, it is experimentally challenging to determine the crystal structure of protein-peptide complexes. To obtain structural information on substrate recognition of peptide-recognizing enzyme, X-ray crystallographic studies were performed using triglycine (Gly-Gly-Gly) as main-chain of peptide. The crystal structure of Parengyodontium album Proteinase K in complex with triglcyine was determined at 1.4 Å resolution. Two different bound conformations of triglycine were observed at the substrate recognition site. The triglycine backbone forms stable interactions with β5-α4 and α5-β6 loops of main-chain. One of the triglycine-binding conformations was identical with the binding mode of a peptide-based inhibitor from a previously reported crystal structure of Proteinase K. Triglycine has potential application X-ray crystallography to identify substrate recognition sites in peptide binding enzymes.

In this review, we show the unique potential of spleen as an optimal site for islet transplantation and a source of mesenchymal stem cells. Islet transplantation is a cellular replacement therapy to treat severe diabetes mellitus, but its clinical outcome is unsatisfactory at present. One factor in clinical success of this therapy is selection of the most appropriate transplantation site. The spleen has been studied for a long time as a candidate site for islet transplantation. Its advantages include physiological insulin drainage and regulation of immunity. Recently it has also been shown that the spleen contributes to the regeneration of transplanted islets. The efficacy of transplantation is not as high as that obtained with intraportal transplantation, which is the current representative method of clinical islet transplantation. Safer and more effective methods of islet transplantation need to be established before the spleen can be effectively used in the clinic. Spleen also has an interesting aspect as a mesenchymal stem cell reservoir. The splenic mesenchymal stem cells contribute to tissue repair in damaged tissue, and thus, the infusion can be a promising therapy for autoimmune diseases, including type 1 diabetes mellitus and Sjogren’s syndrome.

The results shown in this paper extend our research group's previous work, which presents the theoretically achievable hydrogen engine-out NOx (H2-NOx) Pareto front of a hydrogen hybrid electric vehicle (H2-HEV). While the Pareto front is calculated offline, which requires significant computing power and time, this work presents an online-capable algorithm to tackle the energy management of a H2-HEV with explicit consideration of the H2-NOx trade-off. Through the inclusion of realistic predictive data on the upcoming driving mission, a model predictive control algorithm (MPC) is utilized to effectively tackle the conflicting goal of achieving low hydrogen consumption while simultaneously minimizing the NOx. In a case study it is shown that the MPC is able to satisfy user-defined NOx limits over the course of various driving missions. Moreover, a comparison to the optimal Pareto front highlights the MPC's ability to achieve close-to-optimal fuel-performance for any desired cumulated NOx target on four realistic routes for passenger cars.

In this paper, low circumferential reciprocating load foot-scale tests were performed on two truncated PHC B 600 130 tubular piles with bearing nodes to characterize the damage process and morphology of the specimens and to investigate the load-carrying performance of the members. The test results reveal that under the action of tensile-bending-shear loading, the bearing concrete in the node area buckles and is damaged, the anchored reinforcement in the node area yields, the constraint is weakened, an articulation point is formed, and the node rotational capacity increases. When the embedment depth increases from 200 mm to 300 mm, the ultimate bearing capacities of the positive and negative nodes increase by 57.60% and 54.60%, respectively. A numerical simulation is used to verify the test results. Considering the three types of piles with truncated nodes, the numerical simulation is used to analyze the node-bearing capacity at different embedment depths. Finally, two preferred node types are proposed as follows: pipe pile core-filled longitudinal reinforcement anchored into the bearing node and pipe pile body longitudinal reinforcement anchored into the bearing node + pipe pile core-filled longitudinal reinforcement anchored into the bearing node, with preferred embedment depths of 350 mm and 200 mm, respectively.

Abstract: Intra-abdominal abscesses (IAA) may commonly arise following complicated gastrointestinal tract infections and, on occasion, from infections within the urinary system. Many of these IAA are initiated as a consequence of post-surgical complications. These abscesses have a substantial risk of morbidity and mortality. As a result, it is crucial to diagnose and treat them promptly to minimise these adverse outcomes. Therefore, radiological modalities play a vital role in diagnosing, localising, and detecting associated complications of IAA, as sometimes other investigations could be less reliable and non-specific. Radiological modalities are pivotal in achieving an accurate diagnosis, localising the abscesses, and identifying associated complications. This is especially important since alternative investigative methods may be misleading in certain situations. Radiological techniques such as ultrasound scans (USS), contrast-enhanced computed tomography (CECT), and even magnetic resonance imaging (MRI) are immensely helpful in diagnosing these conditions. These imaging tools guide clinicians in determining the most appropriate patient management strategies. In this article, we compile a case series involving tubo-ovarian abscess, appendicular abscess, diverticular abscess and infected walled-off pancreatic necrosis, paying particular attention to radiological features in the diagnosis. Furthermore, we reviewed the existing literature to delineate characteristic radiological features related to the cases we discussed.

To investigate the mass mortality of asari clams triggered by upwelling-driven hypoxia, we conducted biological and oceanographic observations of the Rokujo tidal flat in Mikawa Bay, central Japan. In addition, a simple laboratory experiment was conducted using sediments on a tidal flat containing macrobenthos to examine the possibility of hydrogen sulfide formation in tidal flats. The results of field observations showed that the number and biomass of asari clams decreased from September to October in the tidal flat when hypoxia was intermittent. In particular, hypoxia persisted for approximately one week from September 21, which was associated with the calm weather and stagnation of tidal currents owing to the neap tide. The hydrogen sulfide concentration in the water directly above the sediment exceeded 30 mg L-1 after 3 days of incubation. Our results suggest that the mass mortality of asari clams may be caused by the high concentration of hydrogen sulfide produced by sulfate reduction, which is attributed to the chain of biological die-off caused by the upwelling of hypoxic water mass accompanied by meteorological events, and calm conditions such as the neap tide period.

Abstract: Background and objectives: Symptomatic walled-off pancreatic necrosis is a serious local complication of acute necrotising pancreatitis. The endoscopic step-up approach is the standard treatment for symptomatic walled-off pancreatic necrosis; however, adjunctive radiologic percu-taneous drainage for this condition is controversial. This study compared the clinical and radio-logic resolution of walled-off pancreatic necrosis achieved with the endoscopic step-up approach with or without radiology-guided percutaneous drainage. Material and Methods: This retrospective, single-center cohort study enrolled patients with symp-tomatic walled-off pancreatic necrosis who underwent endoscopic transmural drainage (ETD) followed by directed endoscopic necrosectomy (DEN) with or without radiology-guided drainage. A total of 34 patients (endoscopic approach, n=22; combined modality approach, n=12) underwent the endoscopic step-up approach (ETD followed by DEN). Baseline characteristics, clinical success, and resolution of necrosis were compared between groups. Results: All patients achieved symptom resolution from walled-off pancreatic necrosis. The mean patient age was 58.4 years, and 21 (61.8%) were men. After treatment with the endoscopic approach and combined modality approach, clinical success was achieved in 90.9% of patients within 11.5 days, and 66.7% of patients within 16.5 days, respectively. Both the total hospital stay (55 days vs 71 days; p=0.071) and time to complete radiologic resolution were shorter (93 days vs 124 days; p=0.23) in the endoscopic approach group. Conclusion: The endoscopic step-up approach resulted in the clinical resolution of symptomatic walled-off pancreatic necrosis comparable to that of the combined modality drainage. However, the endoscopic approach alone allows higher clinical success, early clinical and radiologic resolution, and a shorter hospital stay.

Ocean wave energy conversion as one of the renewable clean energy sources is attracting the research interests of many people. This review introduces different types of power take-off technology of wave energy converters. The main focus is the linear direct drive power take-off devices as they have the advantages for ocean wave energy conversion. The designs and optimizations of power take-off systems of ocean wave energy converters have been studied from reviewing the recently published literature. Also, the simple hydrodynamics of wave energy converters have been reviewed for design optimization of the wave energy converters at specific wave sites. The novel mechanical designs of the power take-off systems have been compared and investigated in order to increase the energy harvesting efficiency.

Increasing nitrogen use efficiency (NUE) by improving agricultural practices, soil knowledge and implementing precision agriculture, is essential to reduce the overuse of fertilisers and increase nutrient retention. This study aimed to optimise N management in agriculture by establishing a critical N dilution curve (CNDC) and analysing variations in NUE and N nutrition index (NNI) among different crops under various treatments. Using a Bayesian model, the CNDC was determined as %Nc = 3.63 * PDM-0.71. The results presented that plant dry matter (PDM) and plant N content (PNC) varied significantly with crop type and sampling moments. Strong positive correlations are presented by PDM with N uptake (NUp) (0.89) and NNI (0.88), along with an inverse correlation with critical N concentration (-0.95). The study found that crops under irrigation conditions had higher NUp and higher NNI. This study provides valuable insights into the influence of key management decisions on the N nutritional status of annual ryegrass-based forage crops. The results highlight the critical role of accurate and conscious decision-making in improving NUE and crop yields, emphasising the complex interactions between biomass production and N dynamics in crops. The conclusions allow significant benefits to be realised, contributing to the sustainability of agricultural systems.

MicroRNAs (miRNA) exert regulatory actions via base-pairing with their binding sites on target mRNAs. Cooperative-binding, i.e., synergism, among binding sites on a mRNA is biochemically well-characterized. We studied whether this synergism is reflected in global relationship between miRNA-mediated regulatory activity and miRNA-binding-site count on the target mRNAs, i.e., leading to a non-linear relationship between the two. Recently, using our own and public datasets, we have enquired into miRNA regulatory actions: first, we analyzed the power-law distribution pattern of miRNA binding sites; second, strikingly, mRNAs for core miRNA regulatory apparatus proteins have extra-ordinarily high binding site counts, forming self-feedback-control loops; third, we revealed that tumor suppressor mRNAs generally have more sites than oncogene mRNAs; and fourth, we characterized enrichment of miRNA target mRNAs in translationally less-active polysomes relative to more-active polysomes. In these four studies, obvious correlation was observed qualitatively between the extent to which a mRNA is miRNA-regulated and its binding sites count. This paper summarizes the used datasets. We also re-analyzed the correlation by comparative linear and non-linear regression analyses. The results support a non-linear, instead of linear, relationship between the two parameters, conceivably a transcriptome-level reflection of cooperative-binding/synergism among miRNA binding sites on a target mRNA.

Depression marsh intra- and interspecific facilitation in Southeast Florida, dominated by Hypericum fasciculatum, Stillingia aquatica, and Rhynchospora tracyi were studied as a third installment to the author’s ongoing interest in “Hypericum-Stillingia (HS) marsh” vegetation. The project includes a contextual overview in relation to the HS marsh environmental filter, stress-gradient-hypothesis, and harsh-habitat trait convergence vs. divergence. Using field measurements, transects, and quadrats, the effort focused mainly on two research questions: 1. Does the Hypericum fasciculatum microdistribution relate to marsh microtopography? 2. Does H. fasciculatum have positive or negative associations with other species? Tempered by “cause and effect” concerns, the results supported positive feedback autogenic site alteration by H. fasciculatum along with interspecific facilitation.

The electricity generated from fossil fuel and nuclear energy has negative impacts on the environment and has shown a need to search for and promote the use of clean, renewable and sustainable energy resources such as wind, solar and geothermal resources. Nowadays, wind energy resource has emerged as the fastest-growing source of energy on an overall scale. However, the selection of the best location for constructing a wind farm is a vital issue that can be considered a site selection problem, which involves various conflicting factors. Therefore, it is classified as a multi-criteria decision-making (MCDM) problem. In this research, the site selection of wind power plants is conducted in Burundi country. The Fuzzy Analytic Hierarchy Process (FAHP) was used to weigh the criteria considering their relative importance. The main factors affecting optimal wind farm location considered in this study are wind speed, slope, distance from the grid network, distance to roads, and land use/land cover (LULC). Furthermore, a geographic information system (GIS) is utilized to generate the final suitability wind farm locations map. The obtained results show that 20.91% of the total study area is suitable; nevertheless, only 1.96% is highly suitable for wind farm placement. The western part of Burundi is concluded to be the most suitable area for wind farm construction and the most area is situated in Lake Tanganyika.

Soil erosion due to soil erosion is an important ecological impact factor. In order to further explore the impact and contribution of soil and water conservation measures on sand production and transport in the watershed, and also to provide a reference for soil erosion control, soil and water conservation and ecological environmental protection in the Yellow River Basin. In this paper, based on the measured data from the Henan Soil and Water Conservation Observatory in the Yellow River Basin, we select appropriate equations for quantifying soil erosion factor to calculate the rainfall erosion, topography, soil, vegetation and soil conservation measures in the basin, and then analyse the changes in soil erosion factor and the actual benefits of soil conservation measures in the basin. The results show that there is an increasing trend in the rainfall erosion force factor R in the Yellow River Basin; Soil erosion can be K value made the vertical loess > yellow clunamon soil, the overall change shows a decreasing trend, indicating that erosion control has produced results and that attention should be paid to erosion control in the lithosol region in the future; Since the slope lengths of the runoff plots are laid out consistently with the same LS values for both topographic factors, soil erosion is severely increased when the slope exceeds 20°. The C value of natural vegetation is small, while the C value of bare land is large. The authorities should continue to promote the return of farmland to forests and grasses and pay attention to the self-regulation and restoration of ecosystems; There is an overall decreasing trend in the P value of the soil and water conservation measures factor, the soil and water conservation measures have been effective in providing good protection.

Aiming at the prediction of environmental vibrations induced by elevated high-speed railway, a machine-learning method is developed by combining random forest algorithm and Bayesian optimization, which using the dataset from on-site experiments . When it comes to achieving a rapid and effective prediction of environmental vibration, there is few research on com-parisons and verifications of different algorithms, and neither on parameter tuning and optimi-zation of machine learning algorithms. In this paper, a field experiment is firstly carried out to measure the ground vibrations caused by high-speed trains running on bridge, and then the en-vironmental vibration characteristics are analyzed in view of ground accelerations and weighted vibration levels. Subsequently, three machine-learning algorithms of linear regression, support vector machine and random forest are developed by using experimental database, and their prediction performance are discussed. Finally, two optimization models for the hyperparameter set of random forest algorithm are further compared. It turns out that the integrated random forest algorithm has higher accuracy in predicting environmental vibration than linear regression and support vector machine; the Bayesian optimization has excellent performance and high efficiency in achieving efficient and in-depth optimization of parameters, and can be combined with the RF machine learning algorithm to effectively predict the environmental vibrations induced by the high-speed railway.

For the purpose of this paper, the actual air temperature and air humidity values were monitored in the Visitor Centre of the Archaeological site 1a Imperial Palace Sirmium, designated cultural heritage of exceptional importance. The contamination level of archaeological finds in the site was microbiologically analysed. The findings showed that during the phase of microclimatic monitoring (February–April 2021), air humidity was almost constantly above the levels set by standards and recommendations for museum collections (>60%). The highest levels of air humidity, amounting to 93%, were recorded in February, with daily oscillations of up to 30%; the lowest recorded temperature was 0.3°C, with the maximum daily oscillations of 6°C. Microbiological analysis revealed great diversity in the deterioration level of the finds, which can be attributed to the time lapse between the last conservation and the present. The comparative analysis of microclimatic monitoring and microbiological analysis results identified high levels of relative air humidity as the dominant factor in the increased microbiological contamination of the finds. The findings also pointed to the necessity of continuous microclimatic monitoring during the actual usage of the facility in order to provide the sustainable display and preservation of the finds on the premises.

Species distribution models have become tools of great importance in ecology since the advanced knowledge of suitable habitat of species is needed in the process of the world's biodiversity conservation. Models that use presence-only data are of great interests and are widely used in ecology due to their easy access. However, these models do not estimate accurately the true spatial species distribution based solely on presence-only data since they do not account for biases induced by the sampling techniques used and imperfect detection. To address this gap, Hierarchical integrated models have been recently introduced. Through this study, we assessed the relative performance of these new SDMs models using simulated data. The performance of the models was tested by comparing the estimates of parameters of the distribution models they provide with parameters used to simulate the distribution of the virtual species. The best model was the one whose estimates were close to the true distribution parameters of the virtual species. Results showed that analyzing Presence-only data in conjunction with Point-counts data through the Dorazio's Hierarchical model produced estimates of the coecients of the species intensity models with high precision and less bias while the Koshkina integrated model showed poor performance. Site-occupancy data, being not informative of species abundance, did not allow reducing biases in Presence-only data. The Dorazio's Hierarchical model produced estimates with high precision even with low detection probability. We have also found that the species rarity tends to in ate the variability of the models' estimates making modelling abundant species to be more accurate than modelling less abundant species. Hence, to model the species distribution with high precision based on Presence-only data, additional Point-counts data are required to account for sampling bias and imperfect detection.

The article reviews the current status of label-free integrated optical sensors focusing on the evolution over the years of their analytical performance. At first a short introduction to the evanescent wave optics is provided followed by detailed description of the main categories of label-free optical sensors including sensors based on surface plasmon resonance (SPR), grating coupler, photonic crystals, ring resonators and interferometric transducers. After a short reference to SPR techniques, including localized SPR, integrated optical sensors i.e., grating-couplers, interferometers, photonic crystals, microring resonators are reviewed. For each type of sensor, the detection principle is first provided followed by description of the different transducer configurations so far developed and their performance as biosensors. Finally, a short discussion about the current limitations and future perspectives of integrated label-free biosensors optical sensors is provided

An on-site, ultra-sensitive, and quantitative sensing method was developed based on quantum dot nanobeads (QDNBs) and test strip for the determination of total aflatoxins (AFTs) in rice and peanut. The monoclonal antibody against AFT (mAbAFT) was home-made and labeled with QDNB. After the pre-coating of the AFT antigen on the test line (T line), the competitive immunoreactions were conducted between AFT and AFT antigen on the T line with QDNBs-mAbAFT. Under optimal conditions, this approach allowed a rapid response towards AFT with a considerable sensitivity of 1.4 pg/mL and 2.9 pg/mL in rice and peanut matrices, respectively. The put-in and put-out duration were within 10 min. The recoveries for AFT in rice and peanut samples matrices were recorded from 86.25–118.0% with the relative deviations (RSD) below 12%. The assay was further validated via the comparison between this QDNB strip and the conventional HPLC method using spiked samples. Thus, the design provided a potential alternative for on-site, ultra-sensitive, and quantitative sensing of AFT that could also be expanded to other chemical contaminants for food safety.

A methodology for selecting rational parameters of atmospheric aircrafts at the initial stages of design using an optimization algorithm of differential evolution and numerical mathematical modeling of aerodynamics problems is proposed. The technique involves the implementation of weight and aerodynamic balance in the main flight modes, has the ability to consider atmospheric aircrafts with one or two lifting surfaces, apply parallel calculations and automatically generate a three-dimensional geometric model of aircraft appearance based on the optimization results. A method for accelerating the process of optimizing the parameters of an aircraft in terms of take-off weight by more than three times by introducing a objective function into a set of design variables is proposed and demonstrated. The results of assessing the reliability of the used mathematical models of aerodynamics and the correctness of the calculation the objective function, taking into account various constraints, are presented. A comprehensive test of the performance and efficiency of the methodology is considered by solving demonstration problems to optimize more than ten main design parameters the appearance of two existing heavy-class unmanned aerial vehicles with known characteristics from open sources.

Retinoids are vitamin A derivatives and include trans-retinoic acid, isotretinoin, tamibarotene, and bexarotene, all of which are currently available for clinical use. The clinical development of retinoid therapy for neuroblastoma has a history spanning more than four decades. The most promising agent is isotretinoin, which can contribute to improving event-free survival in patients with high-risk neuroblastoma by approximately 10 % when administered over six months as maintenance therapy. Although isotretinoin is regarded as an essential component in the standard clinical management of high-risk neuroblastoma, its use for this purpose in the US and EU is off-label. To promote isotretinoin use in Japan as a treatment for neuroblastoma, our clinical research team is planning to launch an investigator-initiated, registration-directed clinical trial. The present review article discusses the basic science behind retinoid therapy, pre-clinical / clinical evidence on neuroblastoma, the concept of the proposed clinical trial, and prospects for this therapy.

Lift-offs of the sensor could significantly affect the measurement signal and reconstruction of material properties when using the electromagnetic (inductive) eddy current sensor. Previously, various methods (including novel sensor designs, and features like zero-crossing frequency, lift-off point of intercept) have been used for eliminating the measurement error caused by the lift-off distance effect of the sensor. However, these approaches can only be applied for a small range of lift-off variations. In this paper, a linear relationship has been found between the sensor lift-off and ratio of dual-frequency eddy current signals, particularly under the high working dual frequencies. Based on this linear relationship, the lift-off variation can be reconstructed firstly with a small error of 2.5 % when its actual value is up to 10 mm (10.1 % for 20 mm). The reconstructed lift-off is used to further get the property of the material under a low single frequency. Experiments on different ferrous metals have been carried out for the testing of the reconstruction scheme. Since the inductance is more sensitive to the material property (and less sensitive to the lift-off) under low frequencies, the reconstruction error of the material property is much smaller than that of the lift-off, with 1.4 % under 12 mm (and 4.5 % under 20 mm).

Previously, a conductivity invariance phenomena (CIP) has been discovered – at a certain lift-off, the inductance change of the sensor due to a test sample is immune to conductivity variations, i.e. the inductance – lift-off curve passes through a common point at a certain lift-off, termed as conductivity invariance lift-off. However, this conductivity invariance lift-off is fixed for a particular sensor setup, which is not convenient for various sample conditions. In this paper, we propose using two parameters in the coil design – the horizontal and vertical distances between the transmitter and the receiver to control the conductivity invariance lift-off. The relationship between these two parameters and the conductivity invariance lift-off is investigated by simulation and experiments and it has been found that there is an approximate linear relationship between these two parameters and the conductivity invariance lift-off. This is useful for applications where the measurements have restrictions on lift-off, e.g. uneven coating thickness which limits the range of the lift-off of probe during the measurements. Therefore, based on this relationship, it can be easier to adjust the configuration of the probe for a better inspection of the test samples.

Rising organic charge in northern freshwaters is attributed to increasing levels of Dissolved Natural Organic Matter (DNOM) and shifts in water chemistry. Organic charge concentration may be determined by charge balance calculations (Org.-) or modelled (OAN-) using the conceptual Oliver and Hruška models based on the density of weak acid functional sites (SD) present in DNOM. The charge density (CD) is governed by the SD and protonation and complexation reactions on the functional groups. The models use this SD as a key parameter in empirically fitting the model to Org.-. Utilizing extensive datasets of water chemistry, this study shows that spatial and temporal differences in SD and CD are influenced by variations in the humic-to-fulvic ratio of DNOM and the organic aluminum (Al) complexation, as well as the mole fraction of CD to SD governed by the acidity. Site median SD obtained for 44 long-term monitored acid-sensitive lakes was 11.1 and 13.9 µEq/mg C for the Oliver and the Hruška model, respectively. During the 34 years of monitoring the CD increased by 70%, likely due to rising pH and declining Al complexation with DNOM. Present-day median SD values for the Oliver and Hruška models in 16 low-order streams are 13.8 and 15.8 µEq/mg C, respectively, and 10.8 and 12.5 µEq/mg C, respectively, in 10 high order rivers.

This article aims to assess the benefits of floor-slab insulation measures using extruded polystyrene (XPS) and polyisocyanurate (polyiso) insulation materials at various levels of insulation thicknesses for a detached residential building. The EnergyPlus simulation analysis was carried out within the seven energy zones (represented by eight locations) of South Africa in accordance with the South African national code for building energy efficiency (SANS10400-XA). The energy savings and payback periods due to use of the insulation over a lifecycle period of 50 years were assessed. Cape Town (zone 4) behaved differently from other locations and hardly benefitted from the application of floor-slab insulation measures. Generally, polyiso insulation performed better than XPS, for vertical gap insulation. For vertical gap insulation, lower insulation thicknesses required higher insulation depths to maximize energy savings. Similarly, lower insulation thicknesses required higher perimeter insulation widths to maximize energy savings, for the horizontal perimeter insulation method. The locations that benefitted most from vertical gap floor-slab insulation were Pretoria (zone2), Kimberley (zone6), Nelspruit (zone3), Fraserburg (zone7), Welkom (zone1), Mthatha (zone5), Ixopo (zone5H) and Cape Town (zone4) in that order. This order was almost similar with those for the horizontal perimeter floor-slab insulation and horizontal full floor-slab insulation methods.

The SARS-CoV-2 polybasic furin cleavage site is still a missing link. Remarkably, the two arginine residues of this protease recognition site are encoded by the CGG codon, which is rare in Betacoronavirus. However, the arginine pair is common at viral furin cleavage sites, but are not CGG-CGG encoded. The question is: Is this genetic footprint unique to the SARS-CoV-2? To address the issue, using Perl scripts, here I dissect in detail the NCBI Virus database in order to report the arginine dimers of the Betacoronavirus proteins. The main result reveals that a group of Middle East respiratory syndrome-related coronavirus (MERS-CoV) (isolates: camel/Nigeria/NVx/2016, host: Camelus dromedarius) also have the CGG-CGG arginine pair in the spike protein polybasic furin cleavage region. In addition, CGG-CGG encoded arginine pairs were found in the orf1ab polyprotein from HKU9 and HKU14 Betacoronavirus, as well as, in the nucleocapsid phosphoprotein from few SARS-CoV-2 isolates. To quantify the probability of finding the arginine CGG-CGG codon pair in Betacoronavirus, the likelihood ratio (LR) and a Markov model were defined. In conclusion, it is highly unlikely to find this genetic marker in betacoronaviruses wildlife, but they are there. Collectively, results shed light on recombination as origin of the virus CGG-CGG arginine pair in the S1/S2 cleavage site.

Types of DNA recombination include homologous recombination and nonhomologous recombination. Homologous DNA recombination is a general term that includes exchange of information between chromatids: (reciprocal) crossing-over, gene conversion, and post-meiotic segregation. Gene conversion is now thought to be a type of non-Mendelian segregation of heterozygous markers near the recombination initiation site. Thus, it includes both gene conversion and post-meiotic segregation previously described. DNA non-HR including transpositional recombination and site-specific recombination. Our understanding of the molecular mechanism by which DNA recombination occurs has significantly increased in the past decades. Currently The synthesis-dependent strand annealing model is now thought to give rise to most or all noncrossovers, with the double-strand-break repair model forming mainly crossovers. The Shapiro model proposed by Dr. J. Shapiro explains the molecular mechanism of transpositional recombination. Site-specific recombination results from another distinct model. We previously proposed a novel theory which can provide a more reasonable and simpler explanation accounting for DNA HR including the 3 classes of recombinogenic events described above. In the new supplementedly molecular model, DNA meiotic recombination can be initiated by a copy choice mechanism, that is, copying part of 1 single-stranded DNA template, followed by DNA polymerase switching to another single-stranded DNA template, and then resuming the following DNA synthesis along the new template. The current review suggests that transpositional recombination and site-specific recombination should be initiated by copy choice during DNA synthesis rather than break/join mechanism. The work indicates that review of DNA nonhomologous recombination are very necessary. The novel theory would challenge earlier models accounting for transpositional recombination and site-specific recombination and would be critical to the understanding of the mechanisms. We hope copy choice initiating DNA nonhomologous recombination will be one of the concepts that are explored. Proper and specific experiments are required to reconstruct the detailed mechanism described here.

Using pumps operating as turbines (PATs) offers the possibility of increasing the sustainability of water and energy systems by recovering the excess of energy that would be otherwise lost in pressure reducing valves or head loss chambers. In on-grid applications, there are many research works and implementations of PATs. However, there is still limited research for the optimization of efficiency and stability of PATs operating in off-grid systems. This work contributes to the development of stable direct current (DC) off-grid electric systems based on PATs, by optimizing and analysing the energy efficiency and stability for a wide range of operation. A self-excited induction generator (SEIG) coupled to the PAT is provided to cover the conventional type of electric ma-chines typically coupled to the hydraulic pumps. In this context, a methodology is proposed, based on the hydraulic, mechanical and electric subsystems, to define the PAT-SEIG operational area, to maximize energy conversion and the system efficiency. This will guarantee stable electric output quantities when operating in a DC off-grid system. In addition, an analytical model is proposed to estimate the PAT-SEIG operation under specific conditions. With this, water managers are suitable to design and optimize an off-grid PAT-SEIG system and to define the best hydraulic machines, electronic equipment, and all different control elements to maximize energy conversion within the target of operational limits. To develop and verify this new methodology, two micro PAT-SEIG setups were implemented in the hydraulic laboratory of IST/CERIS under typical operating conditions. The proposed solution proved to be resilient under a variable load regime. The system's maximum efficiency can be adapted using different capacitor values for the excitation of the SEIG, and the operational range is limited to the electric components. Considering the nominal efficiencies of the system’s components, the maximum p.u. efficiency obtained for each PAT-SEIG system were between 0.7 and 0.8 p.u.

Tail-sitters aim to combine the advantages of fixed-wing and rotor-craft, but demand a robust and fast stabilization strategy to perform vertical maneuvers and transitions to and from aerodynamic flight. The research conducted in this work intends to assess the performance of nonlinear control strategies to stabilize the attitude of a X-Vert VTOL aircraft when hovering, comparing existing solutions to applications of Nonlinear Dynamics Inversion (NDI) and its incremental version, INDI. Such controllers are implemented and tuned in simulation in order to stabilize a model of the tail-sitter , complemented by estimation methods that allow to feed back the necessary variables. These estimators and controllers are then implemented in a microcontroller, validating them in a Hardware-in-the-Loop (HITL) scenario, with simple maneuvers in vertical flight. Lastly, the developed control solutions are used to stabilize the aircraft in experimental flight, being monitored by a motion capture system. The experimental results allow to validate the model of the X-Vert and compare the effectiveness of the different control solutions in stabilizing it, with the INDI presenting itself as a more robust control strategy, with better tracking capabilities and less actuator demands.

Accurate evaluation of thermo-fluid dynamic characteristics in tank are critically important for designing liquid hydrogen tank of small-scale hydrogen liquefier to minimize heat in-leak into the liquid and ullage. Due to the huge cost, most future liquid hydrogen storage tank designs will have to rely on predictive computational models for storage tank pressurization and heat-leak minimization. Thus, reliable on predictive numerical models to aid design process of tank design have been required. Therefore, in this study, in order to improve the storage efficiency of the small-scale hydrogen liquefier, a three-dimensional CFD model that can predict the boil-off rate and the thermo-fluid characteristics due to heat penetration has been developed. The prediction performance and accuracy of the CFD model is validated on the basis of the comparisons between its results and previous experimental data and a good agreement is obtained. To evaluate insulation performance of polyurethane foam according to thickness, the pressure change and thermo-fluid characteristics in a partially liquid hydrogen tank, subject to fixed ambient temperature and wind velocity, has been investigated numerically. Three different insulation thickness were considered to investigate not only interfacial characteristics between liquid and ullage but thermo-fluid dynamics in hydrogen storage tank for various heat-leak situation. The results indicate that as the insulation thickness becomes thinner and more heat penetration exists, natural convection by buoyancy develops stronger, so strong vortices are created near the interfacial zone by upward flow driven by buoyancy. In particular, as the amount of heat in-leak increased, wider and stronger heat accumulation was found in the top dished head area of the ullage area. In addition, it was confirmed that the CFD model developed in this study could well describe the phenomenon in which the temperature of the tank wall and the insulation mat increased at a faster rate due to faster heat transfer from the vapor and interface. In the future, the numerical model developed in this study will be used for optimizing insulation system of storage tank for small-scale hydrogen which is cost-effective and highly efficient.

The advancement of computational drug discovery and design necessitates continuous innovation to enhance the accuracy and scope of predictive models for early-stage drug research and development. This article introduces a novel workflow for in silico generation of structural and intermolecular binding affinity data with reasonable accuracy, combining two computational tools: Modeller and Prodigy. By leveraging synthetic structural and biophysical data, this approach addresses the limitations of existing experimental datasets, generating extensive, high-quantity binding affinity data with reasonable accuracy for biomolecular binding pairs, which broadens the horizon of computational biomolecule design and discovery by enabling extensive exploration of the sequence space of biomolecular binding pairs, and narrows the gap between experimental binding affinity data and its unexplored territories. Overall, this article presents a methodological advance to enhance the accuracy and scope of computational biomolecule discovery and design, paves the way for the development of preclinical candidates with improved efficacy and specificity, and holds transformative potential for further advancements in artificial intelligence-enabled biomolecule discovery and design in the future.

Based on the theory that certain geological fault zones surpass the influence of other abiotic and biotic site factors for mound-building red wood ants (Formica rufa group), an area northwest of Tuttlingen with extremely high ant density was systematically surveyed, taking into account official geological maps. Indicators of active fault zones were recorded. These were additionally examined in a model area using a high-resolution digital terrain model (DTM 1-meter). The study area is located in the Swabian Jura at the western edge of the Albstadt shear zone, where recent seismic activity is documented by frequent earthquakes. The earthquakes are considered to be the cause of gas permeability in the strike-slip faults, around which the clustered nesting sites were mapped. More than 2900 nests of the Formica rufa group were mapped and their site conditions analysed in different geomorphological positions. In addition to recording forestry site conditions, a geological classification was carried out, as well as an analysis of soil gases/mofettes in areas with the highest nest densities. The correlation between forestry data and nest sites did not reveal a consistent pattern. In contrast, the relationships with gas-permeable strike-slip faults, though predominantly covered with Quaternary sediments, could be identified through CO₂- and CH₄-rich gas emissions, mofettes, and doline features. The interpretations were complicated due to different mapping ages and signatures of the geological maps. Fortunately, this issue could be analysed and evaluated in a sub-area with mappings from 1936/71 and 1995 regarding presumed or confirmed fault trajectories. New insights were gained regarding the relationships between Formica nest sites, gas-permeable faults, and groundwater levels on narrow mountain ridges with steep relief. Here, the lateral emission of CO₂ depends on the groundwater level and does not occur vertically directly above the fault. C- and H-isotope data of CO₂ and CH₄ do not show a consistent source. While methane is mainly derived from biological production by Archaea in the upper crust and in swamp areas, CO₂ mostly originates from the mantle. The results of the investigations revealed that a multitude of geological and ecological factors must be considered for the interpretation of the occurrences of Formica sites northwest of Tuttlingen. These factors confer a distinct originality to this region, contributing not only to an enhanced understanding of site conditions but also furnishing information regarding environmentally relevant gas emissions.

Growing population, industrialization, and power requirements are adversely affecting the environment by increased greenhouse gases, resulting from fossil fuel burning. Global greenhouse gas mitigation targets have led the nations to promote clean and self-renewable sources of energy to address the environmental issue. Offshore wind power resources are relatively more attractive due to high winds, less turbulence, minimal visualization effects, and no interaction of infrastructure. The present study aims at conducting offshore wind power resources assessment (OWPRA) at some locations in the Gulf of North Suez. For this purpose, the long-term hourly mean wind speed (WS) and wind direction above means sea level (AMSL) and temperature and pressure data near surface is used. The data is obtained from ERA5 (fifth generation reanalysis for the global climate weather) at chosen six (L1-L6) offshore locations. The data covers a period of 43 years, between 1979 and 2021. The WS and direction are provided at 100 m AMSL while temperature and pressure are available near water surface level. At L1 to L6 locations, the log-term mean WS and wind power density (WPD) values are found to be 7.55 m/s and 370 W/m2, 6.37 m/s and 225 W/m2, 6.91 m/s and 281 W/m2, 5.48 m/s and 142 W/m2, 4.30 m/s and 77 W/m2, and 5.03 and 115 W/m2 and at 100 m AMSL; respectively. The higher magnitudes of monthly and annual windy site identifier indices (MWSI and AWSI) of 18.68 and 57.41 and 12.70 and 42.94 at L1 and L3 sites and generally lower values of wind variability indices are indicative of favourable winds source, which is also supported by higher magnitudes of mean WS, WPD, annual energy yields, plant capacity factors, and wind duration at these sites. The cost of energy, for the worst and the best cases are estimated as 10.120 USD/kWh and 1.274 USD/kWh at L5 and L1 sites corresponding to wind turbines WT1 and WT4. Based on the analysis, sites L1, L3, and L2 are recommended for wind farm development in order of preference. The wind variability and windy site identifiers indices introduced, will help decision-makers in deciding the potential windy sites with more confidence.

Abstract: Ambulatory cancer centers face fluctuating patient demand and deploy specialized personnel who have variable availability. This undermines operational stability through misa-lignment of resources to patient needs, resulting in overscheduled clinics, budget deficits, and wait times exceeding provincial targets. We describe deployment of a Learning Health System framework for operational improvements within the entire ambulatory center. Known methods of value stream mapping, operations research and statistical process control were applied to achieve organizational high performance that is data-informed, agile and adaptive. We transitioned from a fixed template model by individual physician to a caseload management by disease site model that is realigned quarterly. We adapted a block schedule model for the ambulatory oncology clinic to align the regional demand for specialized services with optimized human and physical resources. We demonstrated improved utilization of clinical space, increased weekly consistency and im-proved distribution of activity across the workweek. Increased value, represented as the ratio of monthly encounters per nursing worked hours, and increased percentage of services delivered by full-time nurses were benefits realized in our cancer system. The creation of a data-informed demand capacity model enables application of predictive analytics and business intelligence tools that will further enhance clinical responsiveness..

The cardiac sodium ion channel (NaV1.5) is a protein with four domains (DI-DIV), each with six transmembrane segments. Its opening and subsequent inactivation results in the brief rapid influx of Na+ ions resulting in the depolarization of cardiomyocytes. The neurotoxin veratridine (VTD) inhibits NaV1.5 inactivation resulting in longer channel opening times, and potentially fatal action potential prolongation. VTD is predicted to bind at the channel pore, but alternative binding sites have not been ruled out. To determine the binding site of VTD on NaV1.5, we performed docking calculations and high-throughput electrophysiology experiments. The docking calculations identified two distinct binding regions. The first site was in the pore, close to the binding site of NaV1.4 and NaV1.5 blocking drugs in experimental structures. The second site was at the “mouth” of the pore at the cytosolic side, partly solvent-exposed. Mutations at this site (L409, E417, and I1466) had large effects on VTD binding, while residues deeper in the pore had no effect, consistent with VTD binding at the mouth site. Overall, our results suggest a VTD binding site close to the cytoplasmic mouth of the channel pore. Binding at this alternative site might indicate an allosteric inactivation mechanism for VTD at NaV1.5.

The development of platinum group metal-free (PGM-free) electrocatalysts derived from cheap and environmentally friendly biomasses for oxygen reduction reaction (ORR) is a topic of relevant interest, particularly from the point of view of sustainability. Fe-nitrogen-doped carbon materials (Fe-N-C) have attracted particular interest as alternative to Pt-based materials, due to the high activity and selectivity of Fe-Nx active sites, the high availability and good tolerance to poisoning. Recently, many studies focused on developing synthetic strategies, which could transform N-containing biomasses into N-doped carbons. In this paper chitosan was employed as a suitable N-containing biomass for preparing Fe-N-C catalyst in virtue of its high N content (7.1%) and unique chemical structure. Moreover, the major application of chitosan is based on its ability to strongly coordinate metal ions, a precondition for the formation of Fe-Nx active sites. The synthesis of Fe-N-C consists in a double step thermochemical conversion of a dried chitosan hydrogel. In acidic aqueous solution, the preparation of physical cross-linked hydrogel allows to obtain sophisticated organization, which assure an optimal mesoporosity before and after the pyrolysis. After the second thermal treatment at 900 °C, a highly graphitized material was obtained, which has been fully characterized in term of textural, morphological and chemical properties. RRDE technique was used for understanding the activity and the selectivity of the material versus the ORR in 0.5 M H2SO4 electrolyte. Special attention was put in the determination of the active site density according to nitrite electrochemical reduction measurements. It was clearly established that the catalytic activity expressed as half wave potential linearly scales with the number of Fe-Nx sites. It was also established that the addition of the iron precursor after the first pyrolysis step leads to an increased activity because of both an increased number of active sites and of a hierarchical structure, which improves the access to active sites. At the same time, the increased graphitization degree, and a reduced density of pyrrolic nitrogen groups are helpful to increase the selectivity toward the 4e- ORR pathway.

This paper provides a study on the development of solar energy, its prospects, and its impacts in Africa. Although the main focus is on technologies adopted for different uses (solar farms, mini-grids, off-grid, solar houses, irrigation, lighting, etc.), we also consider some aspects that increase the adoption of solar energy, such as legislation and business models. Finally, we will examine current and future solar projects managed by NGOs and international companies and how they benefit to leveraging social and economic standards, quality of life as well as capacity building in Africa. This study shows the plethoric interest of institutions outside Africa in the market of solar energy in the continent and that there is no African strategy to increase its independency toward a sustainable development particularly through energy transition.

Microturbines can be used not only in models and education but also to propel UAVs. However, their wider adoption is limited by their relatively low efficiency and durability. Validated simulation models are required to monitor their performance, improve their lifetime, and design engine control systems. This study aims at developing a numerical model of a micro gas turbine for prediction and prognostics of engine performance. To build a reliable zero-dimensional model, the available compressor and turbine maps were scaled to the available test bench data with the least squares method, to meet the performance of the engine achieved during bench and flight tests. A steady-state aeroengine model was implemented in GSP and compared with experimental operating points. The selected flight data was then used as input for the transient engine model. The exhaust gas temperature (EGT) and fuel flow were chosen as the two key parameters to validate the model, comparing the numerical predicted values with the experimental ones. The observed difference between the model and the flight data was lower than 3% for both EGT and fuel flow.

At 12:28 UTC (8:28 PM, local time) on 15 January 2023, a shallow, moderate earthquake with a magnitude (Mw) of 4.7 and a depth of one (1) kilometer shook the northern part of Leyte Island in the central part of the Philippines. The ground shaking was felt at PHIVOLCS Earthquake Intensity Scale (PEIS) VI, (very strong) equivalent to Modified Mercalli Intensity (MMI) VI in areas along the strike of the Leyte segment of the Philippine Fault. Even though this earthquake is classified as moderate in size, significant geologic, structural, and socio-economic impacts were documented. Most of the earthquake impacts that include surface rupture, liquefaction, and mass movements are limited near the epicentral area. The earthquake produced an 8-km-long surface rupture, the first documented rupture generated by a magnitude <6 along the Philippine Fault, and is unusual in other surface rupturing earthquakes worldwide. It injured 18 persons and damaged 434 residential buildings and 26 public infrastructures which amounts to about 500 thousand US dollars. Structural damages were caused by surface rupture and/or poor engineering construction practices. Analysis of the seismic waveform and recorded peak ground acceleration (PGA) suggests that the subsurface geology influenced the ground motion amplification in an area near the epicenter. Based on the hypocenter, focal mechanism solution, aftershock distribution, and actual field observation, the causative fault for this event is the northern end of the Philippine Fault – Leyte segment. Moderate in size, this earthquake emphasizes the need and importance of documenting moderate-sized earthquakes as a tool and guide for medium and long-term earthquake risk assessment and resiliency.

In view of the problem of charging and hydrogen filling facilities construction in the transition from fuel vehicles to electric vehicles and hydrogen fuel cell vehicles, in order to meet the electric energy demand of electric vehicles and hydrogen energy demand of hydrogen fuel cell vehicles at the same time, this paper puts forward a method of siting and capacity determination of electric-hydrogen refueling integrated station (EHRIS) based on Voronoi diagram and particle swarm algorithm based on calculating the demand of charging and filling of hydrogen in vehicles. Firstly, OD pair(Origin-Destination) is used to represent the starting point and end point of the car to portray the travel demand of the car, and on the basis of the traffic network model, the shortest driving path of the new energy car is determined by Dijkstra algorithm, and Monte Carlo simulation is used to get the electric-hydrogen energy demand of the car; secondly, the Voronoi diagram is introduced to classify the service scope of the electric-hydrogen charging station to determine the equipment capacity of the electric-hydrogen charging station, while taking into account the electric-hydrogen charging and refueling capacity. Secondly, a Voronoi diagram is introduced to divide the service scope of the EHRIS, determine the capacity of the equipment in the EHRIS, and consider the distance constraints between the sites of EHRIS, so as to make the division of the site and service scope more reasonable. Finally, a dynamic optimal current model framework for distribution networks based on second-order cone relaxation is established, and each element of the active distribution network is planned, so that the distribution network can operate safely and stably after being connected to the EHRIS. With the objective of minimizing the total social cost of EHRIS and considering the constraints of the charging equipment and hydrogen production and injection equipment of the EHRIS, a siting and capacity model to meet the electric-hydrogen energy demand of electric and hydrogen fuel cell vehicles is developed, and solved by a particle swarm algorithm. Finally, the simulation planning is carried out with Sioux Falls city and IEEE33 network, which ensures the stable operation of the power grid while meeting the energy demand of automobiles, and the results verify the effectiveness and feasibility of the proposed method.

Hemolysin II (HlyII) – one of the pathogenic factors of Bacillus cereus, a pore-forming β-barrel toxin – possesses a C-terminal extension of 94 amino acid residues, designated as the C-terminal domain of HlyII (HlyIICTD), which plays an important role in the functioning of the toxin. Our previous work described a monoclonal antibody (HlyIIC-20), capable of strain-specific inhibi-tion of hemolysis caused by HlyII, and demonstrated the dependence of the efficiency of hemol-ysis on the presence of proline at position 324 in HlyII outside the conformational antigenic de-terminant. In this work, we studied 16 mutant forms of HlyIICTD. Each of the mutations, ob-tained by multiple site-directed mutagenesis leading to the replacement of amino acid residues lying on the surface of the 3D structure of HlyIICTD, led to a decrease in the interaction of HlyIIC-20 with the mutant form of the protein. Changes in epitope structure confirm the high conformational mobility of HlyIICTD required for the functioning of HlyII. Comparison of the effect of the introduced mutations on the effectiveness of interaction between HlyIICTD and HlyIIC-20 and a control antibody recognizing a non-overlapping epitope enabled identifying the amino acid residues N339, K340 included in the conformational antigenic determinant rec-ognized by HlyIIC-20.

We analyzed the SARS-CoV-2 spike (S) protein amino acid sequence extracted from 11,542 viral genomic sequences submitted to the Global Initiative on Sharing All Influenza Data (GISAID) database through April 27, 2020. Consistent with prior reports, we found a major S protein mutation, D614 to G614, that was represented in 56% of all the analyzed sequences. All other mutations combined were less than 10%. After parsing the data geographically, we found most of the Chinese patient samples showed D614 (97%). By contrast, most patient samples in many European countries showed G614 (51 to 88%). In the United States, the genotypic distribution in California and Washington was similar to Asian countries, while the distribution in other US states was comparable to Europe. We observed a dramatic increase in the frequency of G614 over time in multiple regions, surpassing D614 when both were present, suggesting G614 S protein virus outcompetes D614 S protein virus. To gain insight into the consequences of the D614G mutation, homology modeling using a multi-template threading mechanism with ab initio structural refinement was performed for a region of the S protein (S591 to N710) spanning the D614G mutation and the S1 furin cleavage site. Molecular models of this region containing D614 or G614 revealed a major difference in secondary structure at the furin domain (RRARS, R682 to S686). The D614 model predicted a random coil structure in the furin domain whereas the G614 model predicted an alpha helix. Critical residues in the cleavage domain of G614 model were found to better align with the PDB structure of a furin inhibitor. Thus, homology modeling studies suggest a potential mechanism whereby the D614G mutation may confer a competitive advantage at the furin binding domain that may contribute to the rise of the D614G SARS-CoV-2 mutant.

A variety of techniques have been utilized in metal additive manufacturing (AM) for melt pool size management, including modeling and feed-forward approaches. In a few cases, closed-loop control has been demonstrated. In this research, closed-loop melt pool size control for large-scale, laser-wire based Directed Energy Deposition is demonstrated with a novel modification: site-specific changes to the controller set-point were commanded at trigger points, the locations of which were generated by the projection of a secondary geometry onto the primary 3D-printed component geometry. The present work shows that, through this technique, it is possible to print a specific geometry that occurs beyond the actual toolpath of the print head. This is denoted as an extra-toolpath geometry and is fundamentally different from other methods of generating component features in metal AM. A proof-of-principle experiment is presented in which a complex oak leaf geometry was embossed on an otherwise ordinary double-bead wall made from Ti-6Al-4V. The process is introduced and characterized primarily from a controls perspective with reports on the performance of the control system, the melt pool size response, and the resulting geometry. The implications of this capability, which extend beyond localized control of bead geometry to the potential mitigations of defects and functional grading of component properties, are discussed.

The realization of a BRST cohomology of the 4D topological gauge-affine gravity is established in terms of a superconnection formalism. Identification of fields in the quantized theory is occurred directly as usual in terms of superconnection and its supercurvature components with the double covering of the general affine group GA¯(4,R). Then, by means of an appropriate decomposition of the metalinear double-covering group SL¯(5,R) with respect to the general linear double-covering group GL¯(4,R) one can easily obtain the enlargements of the fields while remaining consistent with the BRST algebra. This leads to the descent equations allowing us to build the observables of the theory by means of the BRST algebra constructed using a sa¯(5,R) algebra-valued superconnection. In particular, we discuss the construction of topological invariants with torsion.

Background: Coronary artery disease (CAD) remains a significant global health concern, being one of the most important contributors to morbidity and mortality worldwide. Accurate assessment of coronary lesions is crucial for guiding appropriate interventions and optimizing patient outcomes. Patients with acute myocardial infarction represent a population which is rarely selected in studies of intracoronary hemodynamics. Fractional Flow Reserve (FFR) has emerged as a valuable physiological index for evaluating the functional significance of coronary lesions, although the data of intravascular hemodynamic evaluation in patients with acute myocardial infarction is scarce [1-3]. In recent years, advancements in intravascular imaging techniques, such as Optical Coherence Tomography (OCT), have provided detailed insights into coronary anatomy both in acute or elective settings. [4-7]. Methods: This article aims to explore the correlation between different non-culprit vessel OCT-parameters and FFR value in the patients with recent acute myocardial infarction. The study included 114 patients with acute myocardial infarction (ST elevation myocardial infarction and non ST elevation myocardial infarction)for whom primary PCI (percutaneous coronary intervention) was performed for the culprit lesion. The non-culprit vessels with intermediate coronary stenoses (157 lesions) were evaluated in a staged procedure (during the index hospitalization) with OCT, FFR and revascularization was performed accordingly. Minimal luminal area (MLA) and percent luminal area stenosis (PSA) were analyzed in relation with the FFR value. Results: There is good correlation between OCT-derived parameters and FFR values in patients with recent acute myocardial infarction. Minimal luminal area (MLA) and percent luminal stenosis area (PSA) were independent predictors of FFR< 0,80 in multivariate logistic regression analysis. A value of 2,08 mm2 for the MLA and 76,85 % for the PSA have proved to be the best cut-offs for predicting a FFR< 0,80. Conclusions: OCT parameters are valuable additional tools in current angiographic practice, including patients with acute myocardial infarction, with the ability to bring numerous direct imagistic and indirect hemodynamic information.

Object of this work is the design and the simulation of a hybrid UAV with VTOL capabilities that has been designed for landing on naval moving platforms. The work is focused on the innovative propulsion layout adopted on the UAV. Authors discuss how adopted low level control strategies can exploit the innovative features of the proposed system assuring a good rejection of transversal wind disturbances. Particular attention is dedicated to low level modelling and control of the system emphasizing how choices regarding low level actuation and control should improve performances and robustness of the system.

A time-sequential working, spatially multiplexed autostereoscopic 3D display design consisting of a fast switchable RGB-color filter array is presented. The wavelength-selective filter barrier emits the light from a display over a larger active area than common autostereoscopic barrier displays. An optical modelling of wavelength-selective barriers has been used for instance to calculate the light ray distribution properties of that arrangement. To find well working display designs, automated searches by simulation and computational evaluation has been proceeded. Wavelength-selective filter barrier arrangements exhibit characteristics different from common barrier displays with similar barrier pitch and ascent. In particular, these constructions show strong angular luminance dependency under barrier inclination specified by correspondent slant angle. In time-sequential implementation it is important to avoid that quick eye or eyelid movement lead to visible color artifacts. In the millisecond regime tunable liquid crystal Fabry-Pérot color filters for the colors red, green and blue are presented. They consist of a sub-micrometer thick nematic layer sandwiched between dielectric mirrors and ITO-electrodes. These cells shall switch narrow-banding light of red, green or blue. An array for a glasses-free 3D display has to be equipped with several thousand switchable filter elements having different color apertures. The newly introduced design is usable as a multi user display as well as a single user system with user adaptive control.

There is currently no effective treatment strategy for the recurrent/metastatic adenoid cystic carcinoma (R/M ACC). Furthermore, recent single-agent and combination immunotherapy trials have failed in unselected ACC cohorts unlike non-ACC salivary gland cancers. Genomic profiling revealed no actionable targets but NOTCH1 and KDM6A frameshift and CTCF splice site mutations (no MYB/L fusion) with a low TMB, MSS and negative PD-L1. We recommended anti-PD-1 plus anti-CTLA-4 combination based on TMB 2-fold greater than median TMB in ACC, tumor harboring multiple immunogenic frameshift or splice site mutations, and PD-L1 negativity. Accordingly, we achieved a complete response in a radiotherapy and chemotherapy-refractory patient with locally recurrent lacrimal gland ACC and lung metastasis following personalized immunotherapy in combination with integrative therapeutics. Therefore, it is crucial to assess not only conventional immune biomarkers but also patient-specific parameters.

Celiac disease is an autoimmune disease triggered by oral ingestion of gluten, with certain gluten residues resistant to digestive tract enzymes. Within the duodenum, the remaining peptides incite immunogenic responses, including the generation of autoantibodies and inflammation, leading to irreversible damage. Our previous exploration unveiled a glutenase called Bga1903 derived from the Gram-negative bacterium Burkholderia gladioli. The cleavage pattern of Bga1903 indicated its moderate ability to mitigate the toxicity of pro-immunogenic peptides. The crystal structure of Bga1903, along with the identification of subsites within its active site, was determined. To improve its substrate specificity toward prevalent motifs like QPQ within gluten peptides, the active site of Bga1903 underwent site-directed mutagenesis according to structural insights and enzymatic kinetics. Among the double-site mutants, E380Q/S387L exhibits an approximately 38-fold increase in its specificity constant toward the QPQ sequence, favoring glutamines at the P1 and P3 positions compared to the wild type. Not only does the heightened specificity of E380Q/S387L improve the hydrolytic activity against pro-immunogenic peptides, but also holds this version of the enzyme as a promising candidate as an oral therapy enzyme for celiac disease.

Important first phases in the process of implementing CO2 subsurface and ocean storage projects include selecting of best possible location(s) for CO2 storage, site selection evaluation. Sites must fulfil a number of criteria that boil down to the following basics: they must be able to accept the desired volume of CO2 at the rate at which it is supplied from the CO2 source(s); they must as well be safe and reliable; and must comply with regulatory and other societal requirements. They also must have at least public acceptance and be based on sound financial analysis. Site geology; hydrogeological, pressure, and geothermal regimes; land features; location, climate, and access, etc. can all be refined from these basic criteria. In addition to aiding in site selection, site characterization is essential for other purposes, such as foreseeing the fate and impacts of the injected CO2, and informing subsequent phases of site development, including design, permitting, operation, monitoring, and eventual abandonment. According to data from the IEA, in 2022, emissions from Africa and Asia's emerging markets and developing economies, excluding China's, increased by 4.2%, which is equivalent to 206 million tonnes of CO2 and were higher than those from developed economies. Coal-fired power generation was responsible for more than half of the rise in emissions that were recorded in the region. The difficulty of achieving sustainable socio-economic progress in the developing countries is entwined with the work of reducing CO2 emissions, which is a demanding project for the economy. Organisations from developing countries, such as Bangladesh, Cameroon, India, and Nigeria, have formed partnerships with organisations in other countries for lessons learn and investment within the climate change arena. The basaltic rocks, coal seams, depleted oil and gas reservoirs, soils, deep saline aquifers, and sedimentary basins that developing countries (Bangladesh, Cameroon, India, and Nigeria etc) possesses all contribute to the individual country's significant geological sequestration potential. There are limited or no carbon capture and storage or clean development mechanism projects running in these countries at this time. The site selection and characterization procedure are not complete without an estimate of the storage capacity of a storage location. Estimating storage capacity relies on volumetric estimates because a site must accept the planned volume of CO2 during the active injection period. As more and more applications make use of site characterization, so too does the body of written material on the topic. As the science of CO2 storage develops, regulatory requirements are implemented, field experience grows, and the economics of CO2 capture and storage improve, so too will site selection and characterisation change.