Advanced high-strength steels (AHSS) have a wide range of applications in equipment safety and lightweight design, and enhancing the strength of AHSS to the ultra-high level of 2 GPa is currently a key focus. In this study, a new process of thermo-mechanical control process followed by direct quenching and partitioning (TMCP-DQP) is developed based on Fe-0.4C-1Mn-0.6Si (wt.%) low-alloy steel, and the effects of microstructure evolution on mechanical properties under TMCP-DQP process and conventional hot rolled quenched and tempered process (HR-QT) are comparatively studied. The results show that the TMCP-DQP process not only shortened the processing steps but also achieved outstanding comprehensive mechanical properties. The TMCP-DQP steel exhibits a tensile strength of 2.23 GPa, accompanied by 11.9% elongation and a Brinell hardness of 624 HBW, with an impact toughness of 28.5 J at -20 ℃. In contrast, the HR-QT steel exhibits tensile strengths ranging from 2.16 GPa to 1.7 GPa and elongations between 5.2% and 12.2%. The microstructure of TMCP-DQP steel primarily consists of lath martensite, containing thin-film retained austenite (RA), nanoscale rod-shaped carbides, and a minor number of nanoscale twins. The volume fraction of RA reaches 7.7%, with an average carbon content of 7.1 at.% measured by three-dimensional atom probe tomography (3DAP). Compared to the HR-QT process, the TMCP-DQP process results in finer microstructure, with a prior austenite grain (PAG) size of 11.91 μm, forming packets and blocks with widths of 5.12 μm and 1.63 μm. The TMCP-DQP process achieves the ultra-high strength of low-alloy steel through the synergistic effects of grain refinement, dislocation strengthening, and precipitation strengthening. The dynamic partitioning stage stabilizes the RA through carbon enrichment, while the relaxation stage reduces a small portion of the dislocations generated by thermal deformation, and the self-tempering stage eliminates internal stresses, all guaranteeing considerable ductility and toughness. The TMCP-DQP process may offer a means for industries to streamline their manufacturing processes and provide a technological reference for producing 2.2 GPa grade AHSS.

The objective of this study is to develop a predictive model for low-carbon bainitic steel utilising the P and λ parameters. The tempering activation energy of the steel was calculated through statistical methods. Kinetic curves for the hardness equivalents and a nomograph for tempering process parameters were plotted. The error analysis indicates that the predicted values based on the λ and P parameters had errors within 15% and 10%, respectively. The model can be effectively utilised to predict mechanical properties and optimise parameters during the tempering process.

In this study, AlSi12 alloy was fabricated using the selective laser melting (SLM) technique to produce high density components with complex and customized parts for railway applications. Nonetheless, the production of dense samples necessitates the optimization of production process parameters. As a statistical design of experimental technique, the response surface methodology was used to optimise different combination of SLM parameters. The results were analysed using analyse of variance (ANOVA) and the signal-to-noise(S/N) ratios. The relationship between the hardness response to the process parameters (scanning speed and lase power) for determining the optimal processing conditions were examined. A hardness value of 133 HV was obtained. The process parameters were successfully optimized and the relationship between the parameters and the structures of the fabricated samples were reported.

Flexible electronics have revolutionized the field by overcoming the rigid limitations of traditional devices, offering superior flexibility and adaptability. Conductive ink performance is crucial, directly impacting the stability of flexible electronics. While metal filler-based inks exhibit excellent conductivity, they often lack mechanical stability. To address this challenge, we present a novel conductive ink utilizing a ternary composite filler system: liquid metal and two micron-sized silver morphologies (particles and flakes). We systematically investigated the influence of filler type, mass ratio, and sintering process parameters on the composite ink's conductivity and mechanical stability. Our results demonstrate that flexible wires fabricated with the liquid metal/micron silver particle/micron silver flake composite filler exhibit remarkable conductivity and exceptional bending stability. Interestingly, increasing the liquid metal content results in a trade-off, compromising conductivity while enhancing mechanical performance. After enduring 5000 bending cycles, the resistance change in wires formulated with a 4:1 mass ratio of micron silver particles to flakes is only half that of wires with a 1:1 ratio. This study further investigates the mechanism governing resistance variation during flexible wire bending. Additionally, we observed a positive correlation between sintering temperature and pressure with the conductivity of flexible wires. The significance of sintering parameters on conductivity follows a descending order: sintering temperature, sintering pressure, and sintering time. Finally, we demonstrate the practical application of this technology by integrating the composite ink-based flexible wires with conductive polymer-based strain sensors. This combination successfully achieved the detection of human movements, including finger and wrist bending.

Polymer-based composites are widely used in the automotive, security, aeronautical and space industries, to mention a few. This is because of their good mechanical properties, which are similar to those of metals but with the attraction of being lightweight. Kevlar® as a reinforcement is extensively used in the security industry owing to its good ballistic properties. This investigation presents the mechanical characterization based on in-plane quasi-static tensile testing of Kevlar® composite using a universal testing system. The methodology developed for the preparation of coupons is based on pressure, temperature and time. As a result of this work, elastic moduli (EL and ET), Poisson’s ratio (νLT), shear modulus (GLT) and strengths (XT, YT, S) were obtained. It is worth mentioning that there is scarce or no characterization of this material in the literature, and those studies that do characterize it do not present the coupon thermoforming conditions or the reasons of the specimen dimensions (width, length and thickness).

The UN Sustainable Development Goal 7 Report 2022 is about ensuring access to clean and affordable energy, which is key to the development of agriculture, business, communications, education, healthcare, and transportation. The lack of access to energy hinders economic and human development. Nevertheless, the current pace of progress is insufficient to achieve Goal 7 by 2030. Huge disparities in access to modern sustainable energy persist. Rising commodity, energy and shipping prices have increased the cost of producing and transporting solar photovoltaics modules, wind turbines and biofuels worldwide, adding uncertainty to a development trajectory that is already far below Goal 7 ambitions. Achieving energy and climate goals will require continued policy support and a massive mobilization of public and private capital for clean and renewable energy such as methane from biomass. An important factor in improving methane yield from biomass waste is pre-treatment of the biomass prior to anaerobic digestion. Size reduction of lignocellulose biomass is important for changing and increasing digestibility thus increasing methane yield. A Hollander beater was used as the mechanical pre-treatment machine throughout this study. Results indicate that methane yield is directly proportional to feedstock/Inoculum (F/I) ratio as higher F/I ratio led to higher methane yield. It was observed at an F/I ratio of 0.5 that 5 minutes pre-treatment time produced highest methane yield, while the lowest methane yield was observed at an F/I ratio of 0.2 with 1 minute of pre-treatment time. Methane yield decreased by 30% from 140 mL gTS-1 at F/I ratio 0.5 with 5 minutes pre-treatment time to 98 mL gTS-1 at F/I 0.2 with 5 minutes pre-treatment time. The optimum methane yield was attained at high F/I ratio allowing sufficient nutrient essential for complete degradation of biomass. Overall, this research shows the Hollander beater is not efficient in optimizing methane yield for cardboard.

In this study, seven mortar mixes were prepared by replacing natural sand by crumb rubber ,CR, (10%, 25%, 50%, 60%, 75% and 100%). The properties of mortars, both in their fresh and hardened states, were studied. Key characterisitcs, including density, water absorption coefficient, porosity, thermal conductivity, heat capacity, shrinkage/swelling, elastic modulus, compressive strength, flexure strength, fracture energy and performance after exposure to heat, were evaluated. The results obtained showed that as the CR fraction increased, density, initial setting time, and workability decreased but mortars with CR fractions ranged between 25% and 50% are lightweight and can be used for repairing as they fulfill satndards. It was observed that strengths and stiffness decreased with higher CR content while shrinkage increased for CR percentage higher than 60%. However, up to 50% of CR content the mortars obey to the standards for repair. Interestingly, incorporating up to 50% waste tires proved to improve comfort and thermal resistance without affecting thermal inertia. A slight increase in the mass loss is observed when mortars are exposed to high temperatures. Mortars containing CR between 25% and 50% can be classified as lightweight and thermally insulating mortars, suitable for repairing concrete structures in accordance with industry standards.

The paper presents research results on biocomposites made from a combination of extruded apple pomace (EAP) and potato starch (SP). The products were manufactured by hot pressing using a hydraulic press with a mold for producing samples. The prepared biocomposites were subjected to strength tests, surface wettability was determined and color analysis was carried out. Thermogravimetric analysis (TGA), Fourier transform infrared spectroscopy (FTIR) and cross section observed in Scanning electron microscope (SEM) were also performed. The obtained test results showed that the combination of apple pomace (EAP) and starch (SP) enabled the production of compact bicomposite materials. At the same time, it was found that each increase in the share of starch in the mixture for producing biocomposites increased the strength parameters of the obtained materials. With the highest share of starch in the mixture, 40%, and a raw material moisture content of 14%, the material had the best strength parameters and was even characterized by hydrophobic properties. It was also found that materials with a high content of starch are characterized by increased temperature resistance. Analysis of SEM microscopic photos showed well-glued particles of apple pomace, pectin, gelatinized starch and a smooth external structure of the samples. Research and analyzes have shown that apple pomace reinforced only with the addition of starch can be a promising raw material for the production of simple, biodegradable biocomposite materials.

Advancements in 3D printing technologies have led to new implementations in rapid prototyping, microfluidics, tooling, dentistry, biomedical devices, drug delivery, and tissue engineering. Stereolithography techniques, which are photopolymerization-based processes, contribute to the optical, chemical, and mechanical properties of 3D printed materials using versatile polymer chemistry. This study used potassium titanate powder (K2Ti8O17) as an additive to enhance the mechanical strength of photocurable resins. PEG was selected as the stabilizer to optimize the dispersion and precipitation of potassium titanate. The flexural strength, hardness, and tensile strength were compared to assess the mechanical strength of the 3D printing resin. The flexural strengths of the printed specimens were in the range of 15–39 N/mm2. The measured surface hardness and tensile strength were 41–80 HV and 2.3–15 N/mm2, respectively. The output resolution of the potassium titanate/acrylate resin was tested using a line-pattern structure. 3D printing resin without stabilizers produced lines with a thickness of 0.3 mm, whereas 3D printing resin containing a stabilizer produced lines with a thickness of 0.2 mm. The flexural strength and pattern thickness results suggest that the potassium titanate/acrylate resin can be utilized as a 3D printer resin, suggesting new possibilities for potassium titanate materials.

In recent times, the soft robotics field is gaining numerous research focus owing to its high level of manipulation capabilities unlike traditional rigid robots, which gives room for an increasing use in other areas. However, compared to traditional rigid gripper robots, being capable of controlling/obtaining overall body stiffness when required is yet to be further explored since soft gripper robots have inherently less rigid properties. unlike previous designs with very complex variable stiffness systems, this paper demonstrates a soft gripper design with minimum system complexity while being capable of varying the stiffness of a continuum soft robotic actuator and proves to have potential applications in gripping objects of various shapes, weights & sizes. The soft gripper actuator comprises two separate mechanisms; the pneumatic mechanism for bending control and the mechanical structure for stiffness variation by pulling tendons using stepper motors which compresses the actuator, thereby changing the overall stiffness. The pneumatic mechanism was first fabricated and then embedded into another silicon layer during which it was as well merged with the mechanical structure for stiffness control. By first pneumatically actuating the actuator which causes bending and then pulling the tendons, we found out that the actuator stiffness value can be increased up to 145 % its initial value, and the gripper can grasp & lift a weight of up to 2.075 kg.

The study of mechanical properties of rock mass can be effectively carried out through rock-like material model test. The similarity of mechanical properties between rock-like material and protolith is dependent on the appropriate selection of composition and content of rock-like materials. In this research, X-Ray diffraction test was conducted to analyze the composition of deep rock, which confirmed silica, quartz, and dolomite as the primary components of deep sandstone. An orthogonal design test was used to execute the ratio test of rock-like material. River sand was used as an aggregate, cement as a binder, gypsum powder as a regulator, and polystyrene foam (EPS) as rock damage simulation material. The influencing factors considered in the orthogonal mechanical tests were the proportion of aggregate and binder, ratio of binder and regulator, quantity of damage simulation material, and size of damage simulation material. Three levels were set for each factor, and mechanical parameters such as compressive strength, tensile strength, elastic modulus, axial strain, and Poisson's ratio were tested for each group of samples. The changes of those parameters with the levels of the above four factors were studied. The study revealed that adjusting the size of polystyrene foam (EPS) can adjust the values of elastic modulus, tensile strength, and Poisson's ratio of rock-like material. Similarly, changing the ratio of binder and regulator can adjust the values of axial strain and compressive strength of rock-like material. The rock-like material developed in the study can simulate the mechanical properties of different rock masses such as granite, sandstone, shale, and limestone.

The effects of post-treatment temperature-based methods on 1D single PLA filaments after FFF have been studied. This lets to decouple the variables related to the 3D structure (layer height, raster angle, infill density, and others) from the variables solely related to the material (molecular weight, molecular orientation, crystallinity, and others). PLA 1D filaments have been aged at 20, 39, 42, 51, 65, 75 and 80 ºC in a water-bath-inspired process in which the hydrolytic degradation of the PLA has been minimised for the ageing temperatures of interest. The evolution of the thermal and mechanical properties of the PLA filaments at different temperatures was recorded. Differential scanning calorimetry (DSC) was used to evaluate thermal and physical properties, in which the glass transition, enthalpic relaxation, crystallisation and melting reactions were analysed. Tensile tests were performed to evaluate the tensile strength and elastic modulus. The flow-induced molecular orientation, the degradation, the logistic fitting and the so-called summer effect –stabilisation of properties at higher temperatures– are discussed for assessing the safeness of accelerating ageing.

The effects of residual stress in a tungsten gate on a polysilicon channel in scaled 3D NAND flash memories were investigated using a technology computer-aided design simulation. The NAND strings with respect to the distance from the tungsten slit were also analyzed. The scaling of the spacer thickness and hole diameter induced compressive stress on the polysilicon channel. Moreover, the residual stress of polysilicon in the string near the tungsten slit had greater compressive stress than the string farther away. The increase in compressive stress in the polysilicon channel degraded the Bit-Line current (Ion) because of stress-induced electron mobility deterioration. Moreover, a threshold voltage shift (△Vth) occurred in the negative direction because of conduction band lowering.

The gastrointestinal (GI) tract is a continuous channel through the body that consists of the esophagus, the stomach, the small intestine, the large intestine, and the rectum. Its primary functions are to move the intake of food for digestion before storing and ultimately expulsion of feces from the rectum through the anal sphincter. The mechanical behavior of GI tissues thus plays a crucial role for GI function in health and disease. The mechanical properties are typically characterized by a constitutive biomechanical model, which is a mathematical representation of the relation between load and deformation in a tissue. Hence, validated biomechanical constitutive models are essential to characterize and simulate the mechanical behavior of the GI tract under physiological and pathological conditions. Numerous constitutive models have consequently been proposed over the past three decades, mainly inspired by work done in cardiovascular tissues. Here, a comprehensive review of these constitutive models is provided. This review is limited to studies where a model of the strain energy function is proposed to characterize the stress-strain relation of a GI tissue. Several needs are identified for more advanced modeling of GI biomechanics including: 1) Microstructural models that provide actual structure-function relations; 2) Validation of coupled electro-mechanical models accounting for active muscle contractions; 3) Human data under physiological and pathological conditions to develop and validate models. The findings from this review provide guidelines for using existing constitutive models as well as perspective and directions for future studies aimed at establishing new constitutive models for GI tissues.

An infestation of parkinsonia (Parkinsonia aculeata) located on Alexandria Station, Northern Territory, Australia was successfully treated with a bioherbicide using stem implanted capsules. The bioherbicide containing three endemic endophytic fungi (Lasiodiplodia pseudotheobromae, Macrophomina phaseolina and Neoscytalidium novaehollan-diae) is the first Australian registered woody weed bioherbicide. The product was effectively administered to the plant stems using a mechanical device, resulting in subsequent development of a dieback event, which, after a period of establishment, has moved through the adjacent untreated plant population resulting in significant decline in infestation vigour and reduced recruitment. This is the first report of large-scale management of parkinsonia by this method.

Mechanical properties of tumor cytoskeleton are extremely vital for any phases of cancer, especially in tumor invasion and metastasis. However, in current category of anticancer drugs, the cytoskeleton-targeting drugs are limited and its role in tumor progression is unclear. Here, we present the mechanical characteristics of tumor stiffness are tightly regulated by cancer cytoskeleton including actin filaments and microtubule during tumor initiation, growth and metastasis, and review the natural drugs that target cancer cytoskeleton. We define cytoskeleton dynamics as target mechanisms for anticancer drug, and summary the plant, microbial and marine sources of natural products. Furthermore, the material approaches to active cancer mechanics are supplied in this review. We aim to promote the development of anticancer drugs that target tumor mechanics by using those material approaches in future and find its pharmacological application.

This paper presents the values of several mechanical characteristics for two blends: H (60% PP + 12% PA6 + 8% EPDM + 20% Polybond 3200) and G (20% PP + 42% PA6 + 28% EPDM + 10% Polybond 3200) (%wt), comparing them to those of PP (polypropylene) and PA6 (polyamide 6). The adding of EPDM (ethylene propylene diene monomer rubber) and Polybond 3200 help reducing the disadvantages of simple blends made of PP+PA6, when the PA6 concentration allows for having a PA6 matrix with droplets of PP. SEM analysis helps for understanding the performance of material G as compared to the neat polymers. EDX analysis proved that there was a matrix inversion, material H having a PP matrix and material G a matrix made of PA6 with droplets of PP. Strain at break for PP and material H were proved to be insensitive to test speed, but materials G and PA6 had large value for strain at break and energy at break for v = 10 mm/min. Taking at basis the values for polyamide 6 (PA6), material G has greater values for energy at break: with 97.8% for v = 10 mm/min, with 29.5% for v= 250 mm/min and with 98% for 1000 mm/min, without exhibiting the micro and macro cavitation of PA6. This means that the recipe, the technology and the mechanical characteristics make material G a potential candidate for applications where a low and moderate impact resistant material is required.

This study aims to identify an optimal heat-treatment parameter set for an additively manufactured AlSi10Mg alloy in terms of increasing the hardness and eliminating the anisotropic microstructural characteristics of the alloy in as-built condition. Furthermore, the influence of these optimized parameters on the fatigue properties of the alloy investigated. In this respect, microstructural characteristics of an AlSi10Mg alloy manufactured by Laser-Based Powder Bed Fusion in non-heat-treated and heat-treated conditions were investigated. Their static and dynamic mechanical properties were evaluated, and fatigue behavior was explained by a detailed examination of fracture surfaces. Much of the microstructure in the non-heat-treated condition was composed of columnar grains oriented parallel to the build direction. Further analysis revealed a high fraction of pro-eutectic α-Al. Through heat-treatment, the alloy was successfully brought to its peak-hardened condition, while eliminating the anisotropic microstructural features. Yield strength and ductility increased simultaneously after heat-treatment, which is due to the relief of residual stresses, preservation of refined grains, and introduction of precipitation strengthening. The fatigue strength, calculated at 10^7 cycles, improved as well after heat-treatment and finally detailed fractography reviled that a more ductile fracture mechanism has happened in the heat-treated condition compared to the non-heat-treated condition.

Currently, one of the biggest issues when developing an ODS alloy is the competition established between the different oxide precursors during the precipitation of oxides which nature depends on their chemical composition. In the presence of various precursors, usually the one with the highest affinity to oxygen leads to the absence of the other oxides. In this work, a new process to equilibrate the local concentration of species and to decrease the competition among them is explained. A unique compound, containing the diverse oxide precursors as one complex oxide, is introduced in a prealloyed 14Cr Steel powder via mechanical alloying. Thus, generating environments enriched in Y, Ti and Zr which, after consolidation, refine the oxides precipitation improving the thermal stability of the alloy. SPS were used as consolidation technique to guarantee shorter sintering times and to maintain the nanostructure obtained. Mechanical properties were tested by tensile tests and Vickers microhardness.

Background - Physiological helical flow in the ascending aorta has been well documented in the last two decades, accompanied by discussions on possible physiological benefits of such axial swirl. Recent 4D-MRI studies on healthy volunteers have shown indication of early generation of helical flow, early in the systole and already close to the valve plane. Objectives - Firstly, the aim of the study is to investigate the hypothesis of premature swirl existence in the ventricular outflow tract leading to already helical flow in the valve plane, and second to investigate the possible impact of two different mechanical valves design on the preservation of this early helical flow and its subsequent hemodynamic consequences. Methods - We use a pulse duplicator with an aortic arch and High Speed Particle Image Velocimetry to document the flow evolution in the systolic cycle. The pulse-duplicator is modified with a swirl-generating insert to generate early helical flow in the valve plane. Special focus is laid on the interaction of such helical flow with different designs of mechanical prosthetic heart valves, comparing a classical bileaflet mechanical heart valve, the St Jude Medical Regent valve (SJM Regent BMHV) with the Triflo trileaflet mechanical heart valve T2B version (Triflo TMHV). Results – When the swirl-generator is inserted, a vortex is generated in the core flow demonstrating early helical flow in the valve plane, similar as observed in the recent 4-D-MRI study taken for comparison. For the Triflo trileaflet valve, the early helical flow is not obstructed in the central orifice, similar as in the case of the natural valve. Conservation of angular momentum leads to radial expansion of the core flow and flattening of the axial flow profile downstream in the arch. Furthermore, the early helical flow helps to overcome separation at the outer and inner curvature. In contrast, the two parallel leaflets for the bileaflet valve impose a flow straightener effect, annihilating the angular momentum with negative impact on kinetic energy of the flow. Conclusion - The results imply better hemodynamics for the Triflo trileaflet valve based on hydrodynamic arguments under the discussed hypothesis. In addition, it makes the Triflo valve a better candidate for replacements in patients with pathological generation of nonaxial velocity in ventricle outflow tract.

The purpose of this study was to develop a mathematical model for non-contacting face seals to analyze how their performance is affected by thermoelastic phenomena. The model was used to solve thermal conductivity and thermoelasticity problems. The primary goal was to calculate the values of thermal deformations of the sealing rings in a non-contacting face seal with a flexibly mounted rotor (FMR) for a turbomachine. The model assumes conversion of mechanical energy into heat in the fluid film. The heat flux generated in the fluid film is transferred first to the sealing rings and then to the fluid surrounding them. An asymmetric distribution of temperature within the sealing rings leads to the occurrence of thermal stresses and, consequently, a change in the rings geometry. The model is solved analytically. The distributions of temperature fields for the sealing rings in the cross-sections are calculated using the Fourier-Bessel series as a superficial function of two variables (r,z). The thermoelasticity problems described by the Navier equations are solved by applying the Boussinesq harmonic functions and Goodier’s thermoelastic displacement potential function. The proposed method involves solving various theoretical and practical problems of thermoelasticity in FMR-type non-contacting face seals. The calculated thermal deformations of the sealing rings are used to determine the most important seal performance parameters such as the leakage rate and power loss.

In this paper, we aim to assess the electric current parameters and report the analysis of the associated degree of ventricular recovery during left ventricular assist device (LVAD) support. An assumption was made there is a linear relationship between ventricular recovery degree and the pump electric current pulsatility index (PI). The experimental study was carried out using the ViVitro Pulse Duplicator System with Sputnik 1 LVAD connected. Cardiac output (CO) and cardiac power output (CPO) were used as a measure of ventricular recovery degree. Different heart rates (HR) (59, 73, 86 bpm) and pump speeds (7600–8400 rpm in 200 rpm steps) were investigated. Ventricular stroke volumes in the range of 30–80 ml for each heart rate at certain pump speed were used. The obtained relationships of CO and CPO vs. PI was linear as the coefficients of determination for each regression curve were more than 0.8. CO vs. PI: R2=0.9218; 0.9271; 0.9172 and CPO vs. PI: R2=0.8517; 0.841; 0.8244 for HR=59 bpm; 73 bpm; 86 bpm, respectively. Study findings suggest that adequate interpretation of parameters could potentially serve as a valuable clinical tool to assess ventricular recovery based on LVAD infrastructure without requiring any special hemodynamic assessment.

Extensive experimental and theoretical research over the past several decades has culminated in the understanding of the mechanisms behind nanoparticle-mediated enhancements on the mechanical properties of hydrogels. This information is not only crucial to realizing applications that directly benefit from developing hydrogels with high mechanical strength, but also to guide the development of strategies to further enhance hydrogel properties by combining different approaches. In our study, we investigated the effect of combining two approaches – addition of nanoparticles and crosslinking two different polymers (to create double-network hydrogels) – on the mechanical properties of hydrogels. Our studies revealed that these approaches may be combined to synthesize hydrogel composites with enhanced properties; however, both polymers in the double-network hydrogel must strongly interact with the nanoparticles to fully benefit from the addition of nanoparticles. Moreover, the concentration of hydrogel monomers used for the preparation of the double-network hydrogels had a significant effect on the extent of nanoparticle-mediated enhancements; double-network hydrogel nanocomposites prepared using lower monomer concentrations showed higher enhancements in elastic moduli compared to those prepared using high monomer concentrations. Collectively, these results demonstrate that the hypotheses previously developed to understand the role of nanoparticles on the mechanical properties of hydrogel nanocomposites may be extended to double-network hydrogel systems and guide the development of next generation hydrogels with extraordinary mechanical properties through a combination of orthogonal approaches.

The article presents a mathematical model to investigate the operability envelopes for subsea production tress (SPT) installation using drill pipe. The finite differential method was used to solve the established governing equations in which the ocean conditions were considered. Based on the evaluations of the ocean wave, ocean current, water depth, specification of drill pipe and SPT weight that might dominate the mechanical behaviors of the pipe, the operability envelopes with permissible ocean conditions for SPT installation were obtained. The results indicate that changes of depths in deep water and SPT weight have few effects on the operation conditions and it would be better to choose smaller pipe to obtain larger permissible ocean conditions during SPT installation.

In this paper, the effect of Bi₂O₃ doping on the mechanical properties of PbO ceramic pellets was studied. For this purpose, different ratios of Bi2O3/PbO (i.e., xBi2O3–(1-x)PbO, where x is 0, 1, 3, 5, 7 wt%) were fabricated and sintered at 570, 620, and 670°C. Mechanical properties including density, hardness, flexural strength, and sintering of PbO were studied for the aforementioned compositions. Phase compositions, microstructures, and worn surfaces of the composites were characterized by scanning electron microscopy and X-ray diffraction (XRD). The XRD analysis revealed that a solid solution formed in the composite ceramic. The best suited conditions of temperature and doping of Bi₂O₃ for optimal sintering are 620°C and 3 wt%, respectively. The hardness of the 3 wt% Bi2O3–97 wt% PbO ceramic was 717 MPa, which is about four times higher than the hardness of pure PbO; in addition, the strength of the composites was 43 MPa, which is two times higher than that of pure PbO. The integrity of the composites was verified using the lead–bismuth eutectic alloy flushing experiment. Results of this research paper are important for future studies of oxygen control in the lead–bismuth eutectic alloy of lead-cooled fast reactors.

In this work 144 reinforcing bars of high-ductility steel named B500SD were subjected to an accelerated corrosion treatment and then tested under tension at different loading speeds in order to assess the effect of corrosion on the ductility properties of the rebars. Results showed that the bars with a corrosion level as low as the one reducing the steel mass by 1% gave rise to a significant degradation on the ductility properties with strain-stress curves losing the yield plateau and behaving practically as cold deformed steel bars. This effect took place at every tested loading speed. Thus, the research significance relies on the assessment of the influence of the loading speed at which the tensile test is performed given that it affects the ductility properties of the reinforcement bars.

To study the feasibility and effect of compounding lignin and its derivatives to improve expansive soil, the physical properties, mechanical properties, and microstructure of the improved soil mixed with calcium lignosulfonate alone, calcium lignosulfonate and lignin fibers were investigated through indoor experiments and electron microscope scanning. Select samples with better performance for water stability tests, and discuss the improvement mechanism of expansive soil by combining macroscopic mechanical changes with microstructural characteristics. The research results show that the addition of calcium lignosulfonate can reduce the water content of the soil and enhance its strength of the soil. The overall performance is the best when the calcium lignosulfonate content is 3%. 3% calcium lignosulfonate compounded with 1.5% lignin fiber has the best all-around performance; the composite improved soil has a better pore-filling effect, the whole is more compact, and the connection between particles significantly enhances the strength, which greatly inhibits the development of cracks good water stability. Lignin and its derivatives compound improved expansive soil have better effect than traditional improvement methods, and have no pollution to the environment, which can provide a particular reference for engineering practice

To study the feasibility and effect of compounding lignin and its derivatives to improve expansive soil, the physical properties, mechanical properties, and microstructure of the improved soil mixed with calcium lignosulfonate alone, calcium lignosulfonate and lignin fibers were investigated through indoor experiments and electron microscope scanning. Select samples with better performance for water stability tests, and discuss the improvement mechanism of expansive soil by combining macroscopic mechanical changes with microstructural characteristics. The research results show that the addition of calcium lignosulfonate can reduce the water content of the soil and enhance its strength of the soil. The overall performance is the best when the calcium lignosulfonate content is 3%. 3% calcium lignosulfonate compounded with 1.5% lignin fiber has the best all-around performance; the composite improved soil has a better pore-filling effect, the whole is more compact, and the connection between particles significantly enhances the strength, which greatly inhibits the development of cracks good water stability. Lignin and its derivatives compound improved expansive soil have better effect than traditional improvement methods, and have no pollution to the environment, which can provide a particular reference for engineering practice.

There always exist steel cuttings, holes and cracks at the interfaces in the explosive composite plate. Multi-pass friction stir processing (M-FSP) is proposed in this research to optimize the interface microstructure and the interface connection for 1060Al/Q235 explosive composite plate. Results show that the microstructures of 1060Al after M-FSP are fine and uniform owing to the strong stirring effect and recrystallization. Micro-defects formed by the explosive welding can be repaired by the M-FSP. However, M-FSP can also form tunnel defects in the aluminum, especially when the passes are one and two. The melting block and the melting lump in the composite plates are easy to become source of crack. The shear strengths and the bending properties for the 1060Al/Q235 explosive composite plate after M-FSP are the best when the passes are three, with the tool rotation speed of 1200rpm and the forward speed of 60mm/min. The optimized interfaces for the explosive composite plate after M-FSP are mainly by the metallurgical bondings, with a certain thickness and are discontinuous. Therefore, the crack extension stress is the largest and the mechanical properties are the best.

Failure characteristics induced by unloading disturbance and the corresponding mechanical mechanism of the coal seam floor are important theoretical bases for water-bursting prevention from the floor of the coal seam and rock burst alarm in deep mining. However, the existing two-dimensional ground-pressure-control theory based on shallow mining cannot sufficiently guide deep-mining practices. In this study, the redistribution of mining-induced stress field in rocks surrounding the longwall face and mechanical behaviors of strata in deep mining are investigated through a combination of numerical simulation, physical simulation, and field measurement. Results demonstrate that mining-induced stress fields in the floor of the longwall face differ in space and time. Vertical stress unloading from top to bottom of the floor and horizontal stress unloading are relatively low. A concentration zone of high horizontal stress exists at stope boundaries. The critical yield load of rock stratum in the floor is determined through thin plate yield theory. Under the combined effect of concentrated high horizontal and vertical resilience stresses, strata in the floor fracture from seam to seam if the load increases to the minimum critical buckling value. Fractured strata slide along the fracture surface, which leads to floor heave. The stope floor shows evident time-delay progressive failure characteristics. The stress shell in the stope floor in deep mining is found to be a sensitive mechanical parameter that produces three-dimensional ground-pressure behavior in the floor. This ground-pressure behavior in the stope floor is controlled by the existence of the corresponding stress shell and effects induced by its space–time evolution. This study provides theoretical basis for the dynamic control of a hazard-inducing environment in engineering and minimizing or altering disaster-occurrence conditions during the construction engineering of the coal seam floor.

The physical and mechanical properties of rocks will change significantly after being subjected to high temperatures, which poses safety hazards to underground projects such as coal underground gasification. In order to investigate the effect of temperature on the macroscopic and microscopic properties of rocks, this paper has taken sandstone as the research object and conducted uniaxial compression tests on sandstone specimens at different temperatures (20-1000 ℃) and different heating rates (5-30 ℃/min) at 1200 ℃. At the same time, the acoustic emission (AE) test system was used to observe the acoustic emission characteristics of the rock damage process, and the microstructural changes after high temperature were analyzed with the help of a scanning electron microscope (SEM). The test results show that the effect of temperature on sandstone is mainly divided into three stages: Ⅰ (20-500 ℃) stage is the strengthening zone, the evaporation of water and the contraction of primary fissures, sandstone densification is enhanced. Specifically, the compressive strength and elastic modulus increase, the macroscopic damage mode is dominated by shear damage, and the fracture micro-morphology is mainly brittle fracture. Stage II (500-600°C) is the transition zone, 500°C is the threshold temperature for compressive strength and modulus of elasticity, and the damage mode changes from shear to cleavage damage, and the sandstone undergoes brittle-ductile transition in this temperature interval. Stage III is the physicochemical deterioration stage. The changes in physical and chemical properties make the sandstone compressive strength and modulus of elasticity continue to decline, the macroscopic damage mode is mainly dominated by cleavage damage, and the fracture microscopic morphology is more toughness fracture. The effect of different heating rates on the mechanical properties of sandstone was further studied, and it was found that the mechanical properties of the rock were more deteriorated under higher heating rates.

The prohibitive costs of small-scale solar photovoltaic (PV) racks decreases PV adoption velocity. To overcome these costs challenges, an open hardware design method is used to develop two novel variable tilt racking designs. These are the first stilt mounted racking designs that allow manual change of tilt angle from zero to 90 degrees by varying the length of cables. The racks are designed using the calculated dead, wind and snow loads for Canada as conservative design for most of the rest of the world. Structural capacities of the wooden members are then ascertained and resisting bending moment, shear force, tensile force, and compressive force for them is calculated. A structural and truss analysis is performed to ensure that racking design with-stands the applicable forces. Moreover, implications of changing the tilt angle on the wooden members/cables used to build the system are also determined. The systems offer significant economic savings ranging from 1/3rd to 2/3rd the capital expenses of the commercially available alternatives. In addition, the racking designs are easy-to-build and require minimal manufacturing operations, which increases their accessibility. The stilt-mounted designs can be employed for agrivoltaic settings while allowing farm workers shaded ergonomic access to perform planting, weeding, and harvesting.

There has been controversy around the mechanical properties of Mg-alloys such as AZ91D and the large variation of these have been seen. The current paper addresses this controversy through specially fabricated samples combined with tensile testing and advanced metallography, including 3D reconstruction of the phases. The results show that despite a more brittle nature of the fracture, the equiaxed microstructure displays a better elongation as compared to a dendritic microstructure. The main conclusion is that this is primarily caused by the nature, or tortuosity, of the Mg17Al12-network in the material.

There is an increase towards reducing the weight of structures through the use of aluminium alloys in different industries like aerospace, automotive, etc. This growing interest would lead towards using dissimilar aluminium alloys which would require welding. TIG and friction stir welding are the well-known techniques that are currently suitable for joining dissimilar aluminium alloys. The welding of dissimilar alloys has its own dynamics which impact on the quality of the weld. This then suggests that there should be a process which can be used to improve the dissimilar alloys welds post their production. Friction stir processing is viewed as one of the techniques that could be used to improve the mechanical properties of the material. This paper reports on the status and the advancement of FSW, TIG and FSP technique. It further looks at the variation use of FSP on TIG and FSW welded joints with the purpose of identifying the knowledge gap.

A potassium bromide KBr material, which has been widely used as the key element in the Fourier spectrometers and as the output window of the IR-lasers, has been studied with good advantage via applying the carbon nanotubes in order to modify the potassium bromide surface. The laser oriented deposition method has been used to place the carbon nanotubes at the matrix material surface in the vertical position at the different electric field varied from 100 to 600 V×cm-1. The main idea of the improvement of the spectral properties of the potassium bromide structure is connected with the fact that the refractive index of the carbon nanotubes is substantially less than the refractive index of the studied material, and the small diameter of the carbon nanotubes allows one to embed these nano-objects in the voids of the lattice of the model matrix systems. Moreover, the mechanical characteristics and wetting features of the potassium bromide structures have been investigated under the condition mentioned above. Analytical and quantum-chemical simulations have supported the experimental results.

Foam concrete is a highly cellularized cementitious material that undergoes extensive plastic deformation when loaded to failure. Under compression, the foam structure gets progressively crushed at a steady stress stage such that a substantial amount of energy is dissipated. Understanding foam concrete crushing behavior is of special importance for its engineering applications such as energy absorber, but the current studies are insufficient to define material properties for design of field applications. This study characterizes the crushing strength and foam modulus of samples with penetration test and resonant frequency test, respectively. A four-phase crushing behavior is observed. The yield strength and plateau strength are identified to characterize the foam crushing. Using the experimental inputs, the modulus-strength constitutive equations are then established. These findings are useful for expanding the knowledge of normal concrete to studies on foam concrete, as well as design of applications.Foam concrete is a highly cellularized cementitious material that undergoes extensive plastic deformation when loaded to failure. Under compression, the foam structure gets progressively crushed at a steady stress stage such that a substantial amount of energy is dissipated. Understanding foam concrete crushing behavior is of special importance for its engineering applications such as energy absorber, but the current studies are insufficient to define material properties for design of field applications. This study characterizes the crushing strength and foam modulus of samples with penetration test and resonant frequency test, respectively. A four-phase crushing behavior is observed. The yield strength and plateau strength are identified to characterize the foam crushing. Using the experimental inputs, the modulus-strength constitutive equations are then established. These findings are useful for expanding the knowledge of normal concrete to studies on foam concrete, as well as design of applications.

In this study composite with alternate layers of 5056 and 1580 alloys was manufactured by wire arc additive manufacturing technology. It is shown that increased strength characteristics of composite material can be obtained due to deformation treatment by high-pressure torsion (HPT) technique. The microstructure and mechanical properties of the HPT-processed material in different structural states were investigated. The HPT-processed material exhibits high value of ultimate tensile strength (~ 770 MPa) but low ductility. Short-term annealing at 250 oС and additional deformation by HPT to 0.25 of revolution at room temperature resulted in a slight decrease in material’s strength to ~ 700 MPa but provided ductility ∼ 9%. Physical mechanisms to improve plasticity in correlation with microstructure evolution is discussed.

Present experimental study assesses the mechanical properties of glass/carbon/glass hybrid composite laminates after exposure to moisture and elevated temperatures for extended periods. The top and bottom layers of the hybrid laminates are glass fiber reinforced and the middle layer is carbon fiber reinforced with the matrix specified as a polymer material. The hybrid laminates were manufactured using the resin transfer molding method and their compressive and tensile properties were determined using a tensile testing machine. The material parameters such as the storage modulus, the loss modulus, and the damping factors of the laminates were identified using dynamic mechanical analysis as a function of the temperature and the vibration frequency. The experimental results on compressive and tensile properties revealed slight variations when the hybrid laminates were kept at low temperatures for extended periods. This might occur due to the increasing molecular cross-linking of the polymer network. As the temperature increased, compressive, tensile, storage modules, loss modulus, and damping factors decreased. This might occur due to the increasing mobility of the binder material. Particularly, the highest stiffness parameters were obtained on -80°C/GCG (Glass/Carbon/Glass) laminates due to the presence of beta transition on the glassy region. The relationships between the glass transitions and the targeted frequencies were characterized. The values of the glass transition shift towards higher temperatures as the frequency increases. This might occur due to a reduction in the gaps between the crosslinking of the epoxy network when the frequency increases. The accuracy of the storage modulus results was compared with the empirical models. The model based on the Arrhenius law provided the closest correlation. Meanwhile, another model was observed that was not accurate enough to predict when gamma and beta relaxations occur under a glassy state.

Literature review indicates that the basic microstructure of Ti-6Al-4V is bimodal which consist of two phases: α + β, and it occurs after the fabrication in conventional methods such as casting, plastic forming or machining processes. After the additive manufacturing methods, there could be significant changes in the microstructure. Due to the rapid heat exchange during heat-treatment process, bimodal microstructure transforms into lamellar microstructure which consists of two phases α′ + β. Despite applying optimum printing parameters, 3D-printed products exhibit typical surface defects and discontinuities. Recently, two of the primary technologies for the improvement of surface layer properties of titanium alloys are shot peening and electropolishing. Literature review signalizes that shot peening and electropolishing processes have positive impact on the corrosion behaviour, mechanical properties and the condition of the surface layer of titanium alloy. Furthermore, there is a lack of studies about combining shot peening and electropolishing in one hybrid process on titanium alloys, which could synthesize the benefits of both processes. The scope of future investigation is also included in this review.

Research on the development of new lightweight Al-Li alloys using selective laser melting pro-cess has great potential for industrial applications. This paper reports on the development of novel aluminum-lithium alloys using selective laser melting technology. Al-Cu-Li-Mg-Ag-Sc-Zr pre-alloyed powders with lithium contents of 1 wt.%, 2 wt.% and 3 wt.%, respectively, were prepared by inert gas atomization. After SLM process optimization, the microstructure and me-chanical properties of the as-formed specimens were investigated. The densification of the three newly developed alloys are 99.51 %, 98.96 % and 92.01 %, respectively. They all have good form-ability, with the lithium loss rate about 15 %. The as-formed alloy with 1% Li content presents good comprehensive properties with a yield strength of 412.6 ± 16.0 MPa, an ultimate tensile strength of 461.1 ± 11.7 MPa, and an elongation of 13.6 ± 1.1%. The three alloys exhibit a layered molten pool stacking morphology and have a typical heterostructure. The columnar crystals and equiaxed fine grains are alternately arranged, and most of the precipitated phases are enriched at the grain boundaries. The change of Li content mainly affects the precipitation of Cu-containing phase. When the Li content is 1 wt.%, there are θ phase, T1 phase and TB phase. When Li increased to 2 wt.%, T1 and T2 phases precipitated together. When Li reaches 3 wt.%, δ' phase precipitates with T2 phase. This study provides useful guidance for the future SLM form-ing of new crack-free and high-strength Al-Li alloys.

In this study, an extensive data set was based on existing literature records in order to enable the suitability of several predictive models, from Multiple Linear Regression (MLR) to Neural Networks (NN). The main objective was to, through regression analyses, generate model computations to correlate tensile properties (UTS- Ultimate Tensile Strength, YTS – Yield Tensile Strength and EF – Elongation-to-Fracture) to a given alloy composition and microstructural spacing. This investigation led to positive results, as the highest accuracies of the trained modules (in 80% of the database) were found to be above ~82% (UTS and EF) and a maximum of ~98% (YTS), when analyzing the results to a test data set. Later, these models were used to define trends for possible next solder alloy commercial compositions. Overall, using the standard model’s setup, the Random Forest and Decision Tree models showed the highest accuracy results, with 0.958 for YTS as opposed to 0.907 for MLR. Moreover, Multilayer Perceptron (MLP)-optimized models yielded the best results for each variable, with the highest increases in accuracy associated with the YTS and EF. The present contribution might imply an important milestone towards alloy design research based on data science guidelines to unlock the full potential of former experiments and their extensive set of results.

In this paper, 6063 aluminum alloy for common building profiles is used as the research object. By adding a new Al-Ti-C-La composite alloy, the effect of 6063 aluminum alloy on the microstructure and properties of 6063 aluminum alloy is studied. The results show that Al-Ti-C-La composite alloy has obvious effect on grain refinement of 6063 aluminum alloy. With the addition of Al-Ti-C-La composite alloy, the grain size decreased significantly. When the addition amount of Al-Ti-C-La composite alloy is 1%, the grain size is reduced from 482 μm to 121 μm. Rare earth La is mainly distributed near the Mg2Si phase and β-AlFeSi, and complex compounds such as AlFeSiMgLa are formed. After aging for 270 days on the basis of T6 heat treatment, the tensile strength and elongation of 6063 aluminum alloy augmented with the addition of Al-Ti-C-La composite alloy, and the Vickers hardness gradually diminished. When the addition amount of Al-Ti-C-La composite alloy is 1%, the tensile strength, elongation and Vickers hardness of 6063 aluminum alloy reach 177.2 MPa, 17.8% and 60.9 HV, respectively, and the tensile strength is increased by 16.3%. The elongation is increased by 50.8%, the Vickers hardness is reduced by 15.4%, and the fracture of the alloy is mainly ductile fracture.

The manufacturing method influences the properties of the produced components. This work investigates the influence of manufacturing methods such as fused filament fabrication (3D printing) and injection molding on water absorption, mechanical and thermal properties of the specimens produced from neat biobased poly(lactic acid) (PLA) polymer and poly(lactic acid)/wood composites. Acrylonitrile butadiene styrene (ABS) acts as the reference material due to its low water absorption and good functional properties. The printing layer thickness is one of the factors that affects the properties of a 3D printed specimen. The investigation includes two different layer thicknesses (0.2 mm and 0.3 mm) while maintaining uniform overall thickness of the specimens across two manufacturing methods. 3D printed specimens absorb significantly higher amounts of water than the injection molded specimens, and the increase in the layer thickness of the 3D printed specimens contributes to further increased water absorption. However, the swelling due to water absorption in 3D printed specimens decreases on increased layer thickness. Tensile, flexural and impact properties of all the specimens decrease after water absorption while the properties improve on decreasing the layer thickness. Higher porosity on increasing the layer thickness is the predominant factor. The results from dynamic mechanical analysis and microscopy validate the outcomes.

Contact inhibition (CI) represents a crucial tumor-suppressive mechanism responsible for controlling the unbridled growth of cells, thus preventing the formation of cancerous tissues. CI can be further categorized into two distinct yet interrelated components: CI of locomotion (CIL) and CI of proliferation (CIP). These two components of CI have historically been viewed as separate processes, but emerging research indicates that they share both distinctive and common pathways. Moreover, they exhibit intriguing intersections with mechanotransduction, a process that involves cells sensing and responding to mechanical forces. This review article describes the intricate interplay between mechanical forces and CI, shedding light on how these forces regulate CIL and CIP. Emphasis is placed on filamin A (FLNA)-mediated mechanotransduction, elucidating how FLNA senses mechanical forces and translates them into crucial biochemical signals that regulate cell locomotion and proliferation. In addition to FLNA, trans-acting factors (TAFs) emerge as sensitive players in both CI and the mechanotransduction process. This article presents methods for identifying these TAFs and profiling the associated changes in chromatin structure, offering valuable insights into CI and mechanotransduction regulation. Finally, it addresses unanswered research questions in these fields and delineates their possible future directions.

To weaken the harm of Al-Si coating and increase the strength of welded joint, variable thickness of Ni foil (Ni, an austenitic formation element) was added into the lap laser welding Al-Si coated 22MnB5 hot stamping steel/galvanized steel joints. The joints' weld appearance, microstructure, and mechanical properties were explored. The weld altered from X-shape to Y-shape with the increased thickness of Ni foil. During welding, Al-Si coating was melted and diluted into the welding pool, forming δ-ferrite (a rich-Al phase with low toughness and strength) in FZ and FB. This phase deteriorated the strength of the joints. After adding Ni, the amount and size of the δ-ferrite phase decreased. With a significant thickness of Ni foil, δ-ferrite would disappear. However, a new phase (FM, rich-Ni phase) probably formed except PM(a no or negligible Ni phase). The heat-affected zone (HAZ) on the side of 22MnB5 comprised a coarse martensite zone, refined martensite zone, martensite+ferrite zone, and tempered martensite zone from the FZ to the basic material. HAZ on the side of galvanized steel mainly contained ferrite and pearlite. After adding Ni foil, the strength of the joint was more than that without Ni. The maximum strength of the joint can be up to 679MPa because of the disappearance of δ-ferrite. Meanwhile, the toughness of the joint increased. The fracture mode was from three mixed fractures(cleavage, quasi-cleavage, and dimple) to one fracture(dimple).

The high demand for lithium (Li) relates to clean renewable storage devices and the advent of electric vehicles (EVs). The extraction of Li ions from aqueous media calls for efficient adsorbent materials with various characteristics, such as good adsorption capacity, good selectivity, easy isolation of the Li-loaded adsorbent, and good recovery of the adsorbed Li ions. The widespread use of metal-based adsorbent materials for Li ions extraction relates to various factors: (i) the ease of preparation via inexpensive and facile templation techniques, (ii) excellent selectivity for Li ions in a matrix, (iii) high recovery of the adsorbed ions, and (iv) good cycling performance of the adsorbents. However, the use of nano-sized metal-based LISs is limited due to challenges associated with isolating the loaded adsorbent material from the aqueous media. Adsorbent granulation process employing various binding agents (e.g., biopolymers, synthetic polymers, and inorganic materials) affords functional particles with modified morphological and surface properties that support easy isolation from the aqueous phase upon adsorption of Li ions. Biomaterials (e.g., chitosan, cellulose, alginate, and agar) are of particular interest because their structural diversity renders them amenable to coordination interactions with metal-based LISs to form 3D microcapsules. The current review highlights recent progress in the use of biopolymer binding agents for the granulation of metal-based LISs, along with various crosslinking strategies employed to improve the mechanical stability of the granules. The study reviews the effects of granulation and crosslinking on adsorption capacity, selectivity, isolation, recovery, cycling performance and the stability of the LISs. Adsorbent granulation using biopolymer binders has been reported to modify the uptake properties of the bio-adsorbent materials to varying degrees, in accordance with the surface and textural properties of the binding agent. The review further highlights the importance of granulation and crosslinking for improving the extraction process of Li ions from aqueous media. This review contributes to manifold areas related to industrial application of LISs, as follows: 1) to highlight recent progress in the granulation and crosslinking of metal-based adsorbents for Li ions recovery, 2) to highlight the advantages, challenges, and knowledge gaps of using biopolymer-based binders for granulation of LISs, and finally, 3) to catalyze further research interest into the use of biopolymer binders and various crosslinking strategies to engineer functional adsorbent materials for application in Li extraction industry. Properly engineered extractants for Li ions are expected to offer various cost benefits in terms of capital expenditure, percent Li recovery, and reduced environmental footprint.

Exploring the fundamental mechanisms of locomotion extends beyond mere simulation and modeling. It necessitates the utilization of physical test benches to validate hypotheses regarding real-world applications of locomotion. This study introduces cost-effective modular robotic platforms designed specifically for investigating the intricacies of locomotion and control strategies. Expanding upon our prior research in Electric-Pneumatic Actuation (EPA), we present the mechanical and electrical designs of the latest developments in the EPA robot series. These include EPA Jumper, a human-sized segmented monopod robot, and its extension EPA Walker, a human-sized bipedal robot. Both replicate the human weight and inertia distributions, featuring co-actuation through electrical motors and pneumatic artificial muscles. These low-cost modular platforms, with considerations for degrees of freedom and redundant actuation, 1) provide opportunities to study different locomotor subfunctions— stance, swing, and balance; 2) help investigate the role of actuation schemes in tasks such as hopping and walking; and 3) allow testing hypotheses regarding biological locomotors in real-world physical test benches.

In 1911, A. Einstein suggested that gravity affects at the electromagnetic radiation originating from the distant sources, namely, it shifts the spectral lines in the red side of the spectrum and derived the gravitational redshift formula. A modern science claims that Einstein’s formula is mathematically immaculate. We show that this is not true: in fact, this formula is approximate. Using the law of conservation of mechanical energy, we derived two exact formulas оf the gravitational redshift.

A CoCrFeNiNb0.65 eutectic high-entropy alloys (EHEAs) prepared by arc melting were irradiated with a 100 keV He+ ion beam. Swelling, helium bubbles and mechanical response induced by irradiation were evaluated. When the ion fluence reached 1.0×1018 ions/cm2, the irradiation-induced swelling occurred on the sample surface, and as the ion fluence increasing, the swelling became increasingly severe and the surface of Nb-rich phase appeared peeling and shedding. Meanwhile, along the boundaries of matrix and Nb-rich phase there was a neat line of helium bubbles. The size of these helium bubbles decreased with distance from the center of the helium bubble layer. This result indicated that the phase boundaries were favorable sites for the nucleation and gathering of helium bubbles. Nanoindentaion results indicated that hardening and softening induced by He+ ion irradiation occurred in various ion fluences. At ion fluence of 5.0×1017 ions/cm2, the CoCrFeNiNb0.65 EHEAs exhibited an obvious hardening behavior, which can be explained by dislocation-dominated hardening effect. When the ion fluence reached 1.0×1018 ions/cm2 and 2.0×1018 ions/cm2, the hardening effect decreased probably due to the helium bubble aggregation and growth, as well as helium bubbles induced noncompact structures. The results of this study provide insights into the effect of helium bubbles on mechanical evolution and pave the way for designing EHEAs suitable for the nuclear industry.

This study investigates the influence of the porous structure, on the density and the mechanical behaviour of new foam concretes incorporating hemp shives. A total of eight batches of foam concretes were manufactured and tested, made with a protein-based foam agent, containing cement, ground granulated blast furnace slag and Metakaolin as binder and hemp shives as natural aggregate. The effect of several parameters is studied, elaboration method (direct and preformed), amount of pozzolanic additions (0% and 30%) and incorporation of hemp shives (5 and 15 vol%) on the resulting physical properties, microstructure, porous structure and mechanical behaviour of the concretes. Hemp shives incorporation results in increased concrete porosity and air bubble radius, decreased uniformity and mechanical strength, and lower cohesion with the cement matrix compared to standard concretes.

Background: For the treatment of bone defects, biodegradable compressive biomaterials are needed as a substitute, which degrade at the same rate as the bone regenerates. In this study, the compressive strength of CPC ceramics (with a layer thickness of more than 12 layers) should be compared with sintered ceramics. Methods: Round scaffolds with 20, 25, 30 and 45 layers were 3D printed the 3D Bioplotter, solidified in a water-saturated atmosphere for 3 days and then tested for compressive strength together with a sintered ceramic using a Zwick universal testing machine. Results: The 3D printed scaffolds are more compressive at 41.56 ± 7.12 MPa than the sintered ceramic at 24.16 ± 4.44. Conclusions: The round geometry sintered ceramics approach or exceed the upper limit of the compressive strength of cancellous bone in the direction of compacta (depending on the author).

In order to understand the impact of lithologic heterogeneity of continental mixed fine-grained sedimentary rocks on reservoir brittleness in western Qaidam basin, the mechanical properties of the rocks and their correlation with mineral composition and petrographic characteristics were studied by measns of mineralogy, petrography and triaxial stress test. The results show that the reservoir rocks can be divided into 5 different types according to the mechanical properties of the reservoir (characteristics of stress-strain curves), among them Type I and III belong to similar elastoplastic failure model, type II shows a special pulse failure mode for plastic material, type IV shows a failure mode of mixed characteristics, and type V exhibits a typical plastic failure model. The correlation between minerals and mechanical properties indicates that quartz and feldspar, which are often considered brittle minerals, do not contribute much to the brittleness of continental fine-grained sedimentary rocks. The main minerals affecting reservoir brittleness are dolomite and clay minerals, and their contributions to reservoir brittleness are positive and negative, respectively. The petrographic analysis results prove that the abnormal correlation between rock mechanical properties and quartz and feldspar is caused by the different rock fabrics. When dolomite forms a rock skeleton, it typically exhibits greater strength, brittleness and physical properties than other minerals. Based on the results, a brittleness evaluation standard for continental fine-grained sedimentary rock reservoir is proposed, and the validity of the standard is verified by the spatial correlation between the lithology probability model and the micro-seismic monitoring data, indicating that the spatial heterogeneity of dolomite-rich rock is the main controlling factor for the development of ‘sweet spot’ in the Cenozoic continental fine-grained sedimentary rock reservoir in the Western Qaidam Basin.

The high entropy alloy (HEA) of equiatomic composition CrNiFeCoMn and with FCC crystal structure was additively manufactured with a selective laser melting (SLM) process starting from mechanically alloyed powders. The as produced alloy shows finenitride and  phase pre-cipitates, which are Cr-rich and stable up to about 900 K. The precipitates increase in number and dimensions after long-period annealing at 900-1300 K, with a change in the HEA mechanical properties. Higher aging temperatures in furnace, above 1300 K, turn the alloy in a single FCC structure, with disappearance of the nitrate and  phase precipitates inside the grains and at the grain boundaries, but with still a presence of a finer Cr-rich nitride precipitation phase. These re-sults suggest that the as-produced HEA is a supersatured solid solution at low and intermediate temperature with nitrides and  nanostructures.

The mechanical properties and stability of hydrophobic surface structures prepared by traditional methods are still the main technical bottlenecks restricting the broad application of hydrophobic systems on workpiece surfaces. In this contribution, we propose a technique called selective laser shock peening (SLSP) to enable large-scale high efficient, low-cost manufacturing of hydrophobic metal surfaces with enhanced mechanical properties for durable applications. Using the method of experimental investigation combined with numerical calculation, the hydrophobic properties, mechanical properties, and tribological properties of the samples prepared under SLSP, all-laser shock peening (ALSP), and non-laser shock peening (NLSP) are studied. The SLSP process could prepare a 3D gradient structure material with surface structures, a two-phase (strong phase, soft phase) distribution on the surface, and a multi-level gradient distribution in the thickness direction. Compared with the 2D gradient structure prepared by the traditional process, 3D gradient structures by SLSP have more significant advantages in improving the wetting behavior and the mechanical properties of the material, which proves SLSP to be a novel method to fabricate functional metal surface structures, with highly high engineering application value.

Metal 3D printing technology is a promising manufacturing method. The quality of the printed product can pass for mechanical application, if the anisotropy of the microstructure, imperfections, deformation, and residual stress of the printed sample could be lower than the appropriate level or if they are fully illuminated. Thermal stress is one of the significant reasons for deformation in the 3D printed samples. Thermal stresses are the direct consequence of the local temperature gradient. In this research, the effect of the temperature printer’s chamber (from room temperature to 900 C) was studied on thermal stress and subsequent total deformation in the printed sample. The printed sample is a six-layers-printed walk, which could be considered as a building block of other complex shapes and give us inside about deformation. The computational results show a meaningful reduction in thermal stress and deformation at the higher temperature of the printer’s chamber. The lower final deformation of the printed sample is an important subject, especially for samples with complex shapes.

Existing rammed earth construction methods have disadvantages such as increased initial costs for manufacturing the large formwork and increased labor costs owing to the labor-intensive construction techniques involved. To address the limitations of existing rammed earth construction methods, an autonomous rammed earth construction method is introduced herein. As this autonomous rammed earth construction method uses a modular formwork, alternative materials must be used in the construction to satisfy the requirements for the early-age binder performance. Accordingly, this study evaluates the use of an epoxy emulsion composed of epoxy and a hardener to enhance the performance of the binder. Preliminary experiments were conducted to determine the optimal formulation of the epoxy emulsion, following which the compressive strength, water loosening, shrinkage, rate of mass change, and microstructure of several red clay binder specimens with and without epoxy emulsion were analyzed at early ages. The results confirmed that the epoxy emulsion can be applied to satisfy the performance requirements for autonomous rammed earth construction by improving the durability and strength of the binder at early ages.

Mucosal irritation caused by cusps of upper and lower teeth represents a source of persistent, low grade mechanical trauma. This type of trauma can initiate and/or perpetuate oral lichen planus in a few susceptible patients. Here, we report a rare case of bilateral white linear striations in the buccal mucosa of a young patient, associated with sharp cusps. Oral lesions demonstrated a unique cuspal signature highlighting the causal role of subtle mucosal trauma in the genesis of reticular-oral lichen planus. Lesions appeared to be exacerbated by significant psychological distress experienced by the patient. Although the Koebner phenomenon is well reported in the cutaneous lichen planus literature, such presentations are relatively rare in the oral cavity. This report emphasizes the potential role of low-grade cuspal trauma/irritation in conjunction with psychological distress in the genesis of oral lichen planus.

There is currently an interest in “active” implantable biomedical devices that include mechanical stimulation as an integral part of their design. This paper reports the experimental use of a porous scaffold made of interconnected networks of slender ferromagnetic fibres that can be actuated in vivo by an external magnetic field applying strains to in-growing cells. Such scaffolds have been previously characterized in terms of their mechanical and cellular responses. In this study, it is shown that the shape changes induced in the scaffolds can be used to promote osteogenesis in vitro. In particular, immunofluorescence, gene and protein analyses reveal that the actuated networks exhibit higher mineralization and extracellular matrix production, and express higher levels of osteocalcin, alkaline phosphatase, collagen type 1a1, runt-related transcription factor 2 and bone morphogenetic protein 2 than the static controls at the 3-week time point. The results suggest that the cells filling the inter-fibre spaces are able to sense and react to the magneto-mechanically induced strains facilitating osteogenic differentiation and maturation. This work provides evidence in support of using this approach to stimulate bone ingrowth around a device implanted in bone and can pave the way for further applications in bone tissue engineering.

By using hydrogen quench continuous annealing technology, Stelco Inc. has developed a suite of Advanced High Strength Steel (AHSS) grades with tensile strength greater than 1000MPa to meet standard automotive specifications and for unique customer requirements. These grades were optimized by correlating chemical composition and processing parameters with microstructures and mechanical properties. Dual-Phase 980 (Stelco trademarked STELMAXTM 980DP), Multi-Phase 1180 (STELMAXTM 1180MP), Martensitic Steel 1300 (STELMAXTM 1300M) and 1500 (STELMAXTM 1500M) products met strength and formability requirements with excellent flatness and surface quality. Hydrogen quench continuous annealing technology not only ensures all developed AHSS grades have consistent mechanical properties across the entire strip length (from strip head to tail) and width (from edge to edge), but also produces high product yield compared with other continuous annealing processes.

We demonstrate fabrication of single-mode optical waveguides on lithium niobate on insulator (LNOI) by optical patterning combined with chemo-mechanical polishing. The fabricated LNOI waveguides have a nearly symmetric mode profile of a mode field size of ~2.5 µm (full-width at half maximum). We develop a high-precision measurement approach by which the single mode waveguides are characterized to have a propagation loss of ~0.042 dB/cm.

We report fabrication of a multifunctional photonic integrated chip on lithium niobate on insulate (LNOI), which is achieved by femtosecond laser assisted chemo-mechanical polish. We demonstrate a high extinction ratio beam splitter, a 1 × 6 optical switch, and a balanced 3 × 3 interferometer on the fabricated chip by reconfiguring the microelectrode array integrated with the multifunctional photonic circuit.

Lightweight composite sandwich structures are laminated composite structures that are composed of thin stiff face sheets bonded to a thicker lightweight core in between. These structures have high potential to be used in marine, aerospace, defense and civil engineering applications due to their high strength to weight ratios and energy absorption capacity.In this study, composite sandwich structures were developed with carbon fiber reinforced polymer composite face sheets and aluminum honeycomb core materials with various thicknesses. Carbon fiber/epoxy composite face sheets were fabricated with lamination of [0/90]_s carbon fabrics by vacuum infusion technique. Al honeycomb layers were sandwiched together with the face sheets using a thermosetting adhesive. Mechanical tests were carried out to determine the mechanical behavior of face sheets, Al cores and the composite structure. Effect of core thickness on the mechanical properties of the sandwich was investigated.

Structural DNA nanotechnology provides an excellent foundation for diverse nanoscale shapes that can be used in various bioapplications and materials research. From all existing DNA assembly techniques, DNA origami has proven to be the most robust one for creating custom nanoshapes. Since its invention in 2006, building from the bottom up using DNA has drastically advanced, and therefore, more and more complex DNA-based systems have become accessible. So far, vast majority of the demonstrated DNA origami frameworks are static by nature, but interestingly, there also exist dynamic DNA origami devices that are increasingly coming into view. In this review, we discuss DNA origami nanostructures that perform controlled translational or rotational movement triggered by predefined DNA strands, various molecular interactions and/or other external stimuli such as light, pH, temperature and electromagnetic fields. The rapid evolution of such dynamic DNA origami tools will undoubtedly have a significant impact on molecular scale precision measurements, targeted drug delivery and diagnostics, but they can also play a role in development of optical/plasmonic sensors, nanophotonic devices and nanorobotics for numerous different tasks.

Copper mine tailings are the residual products after the purification of precious copper from copper ores, and their storage can create numerous environmental problems. Many researchers have used copper mine tailings for preparation of geopolymer. This paper studies the enhancement of the cementitious activity of copper mine tailings in geopolymer system. First, copper mine tailings are activated through a mechanical grinding activation. Afterward, the mechanically activated copper mine tailings are further processed through thermal activation and alkaline roasting activating. The cementitious activity index of copper mine tailings is characterized through the degree of concentration of alkali leaching silicon and aluminum. It was observed that the Si and Al alkali leaching concentration of mechanical activated tailings was increased by 26.03% and 93.33%, respectively. The concentration of Si and Al was increased by 54.19% and 119.92%, respectively. For alkaline roasting activating, roasting time, temperature and (C/N ratio) were evaluated through the orthogonal test, and the best condition was activation for 120 min at 600℃ with C/N ratio is 5:1. In this study, the SEM, XRD and IR analysis show that mechanically activation, thermal activation and alkaline roasting activating can improve the cementitious activity index of copper mine tailings.

This study examines the impact of the impregnation of fireclay-based conventional (CC) and medium cement castables (MCC) with liquid sodium silicate glass under vacuum conditions. The goal is to assess how this treatment affects physical, mechanical properties, and durability (alkali and thermal shock resistance) of these castables used in biomass combustion boilers, where they are exposed to temperatures up to 1100°C. The research work employs standard test methods to evaluate physical and mechanical properties. Additionally, advanced techniques such as scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), and specific tests for alkali resistance and thermal shock resistance are used. The research findings suggest that impregnation with sodium silicate glass under vacuum significantly enhances the alkali resistance of both CC and MCC castables. This improvement is primarily due to the reduction in porosity and the increase in density. SEM images reveal that impregnated samples are coated with a glassy layer and the pores are partially filled with sodium silicate. Tests for alkali resistance demonstrate the formation of a protective glassy layer (with a thickness of 0.9-1.5 mm) on the castables surfaces, thereby reducing further penetration of alkali into deeper layers of the samples. However, it is important to mention that impregnated refractory castables have reduced resistance to thermal shock cycles.

This research examines the fire resistance of geopolymer composites (GCs), formulated using alka-li-activated metakaolin and aluminum powder. The production method involves spray-coating carbon steel plates with fresh GCs, followed by a 28-day curing period at room temperature. Sub-sequently, fire performance and aging tests are conducted to evaluate fire resistance. The study investigates GC properties, including apparent density, bending strength, compression strength, thermal conductivity, porosity, and production cost. Morphological changes before and after fire and aging tests are analyzed using scanning electron microscopy (SEM). Results demonstrate GC foams' outstanding thermal insulation, providing up to 75 minutes of fire resistance with a 6 mm coating, reducing temperatures by 300 °C compared to uncoated steel. GCs exhibit a density of 670 kg/m³, thermal conductivity of 0.166 W/m·K, 68% porosity, and cost efficiency at 250 dollars per cubic meter. This study underscores the potential of foamed geopolymer coatings for effective and economical surface protection.

Virus diseases of strawberry present several complex problems. More than 25 viruses have been described in the genus Fragaria thus far. Here, we describe a novel rhabdovirus, tentatively named strawberry virus 1 (StrV-1), that infects F. ananassa and F. vesca plants. Genomic sequences of three distinct StrV-1 genotypes co-infecting a single F. ananassa host were obtained using combined Illumina and Ion Proton high-throughput sequencing. StrV-1 was transmitted to herbaceous plants via Aphis fabae and A. ruborum, further mechanically transmitted to Nicotiana occidentalis 37B and sub-transferred to N. benthamiana, N. benthamiana DCL2/4i, N. occidentalis 37B and Physalis floridana plants. Irregular chlorotic sectors on leaf blades and the multiplication of calyx leaves seem to be the diagnostic symptoms for StrV-1 on indexed F. vesca clones. StrV-1 was detected in asymptomatic grafted plants and in 49 out of 159 field strawberry samples via RT-PCR followed by Sanger sequencing. The bacilliform shape of the virions, which have a cytoplasm-limited distribution, their size, and phylogenetic relationships support the assignment of StrV-1 to a distinct species of the genus Cytorhabdovirus. Acyrthosiphon malvae, A. fabae and A. ruborum were shown to transmit StrV-1 under experimental conditions.

Background: Number of joint infections caused by Vancomycin-resistant pathogens is emerging. Currently no PMMA cement is commercially available to cover VRE. Daptomycin shows promising results in infection treatment, offers a good safety profile and reduced risk for resistance development. Purpose of this in vitro study is to investigate the mechanical stability, handling properties, elution behavior and antimicrobial effectiveness of PMMA cement loaded with three different Daptomycin concentrations in comparison to commercially available ALBC; Methods: Mechanical properties and handling characteristics (ISO 5833, DIN 53435), HPLC elution, antimicrobial effectiveness with proliferation assay (DIN 17025) and inhibition zone testing were investigated; Results: All tested Daptomycin concentrations fulfilled ISO and DIN mechanical strength. Dosage of 0.5. g added Daptomycin did not show any antimicrobial effectiveness in contrast to 1.0 g and1.5 g. Cement with 1.5 g Daptomycin was best in elution and effectiveness, showed good mechanical ISO strength, ISO doughing was a little longer sticky and setting was faster as Vancomycin containing reference cement; Conclusion: PMMA cement containing 0.5 g Gentamicin and 1.5 g Daptomycin could be a good alternative to the already established COPAL® G+V for PJI treatment of VRE.

This review is devoted to present the history of CARDIOSIM© software simulator platform, which was developed in Italy to simulate the human cardiovascular and respiratory system. The first version of CARDIOSIM© was developed at the Institute of Biomedical Technologies of the National Research Council in Rome. The first platform version published in 1991 ran on PC with disk operating system (MS-DOS) and was developed using the Turbo Basic language. The last version runs on PC with Microsoft Windows 10 operating system; it is implemented in Visual Basic and C++ languages. The platform has a modular structure consisting of seven different general sections, which can be assembled to reproduce different pathophysiological conditions. The software simulator can reproduce the most important circulatory phenomena in terms of pressure and volume relationships. It represents the whole circulation using a lumped-parameter model and enables the simulation of different cardiovascular conditions according to Starling’s law of the heart and a modified time-varying elastance model. Different mechanical ventilatory and circulatory devices have been implemented in the platform including thoracic artificial lung, ECMO, IABP, pulsatile and continuous right and left ventricular assist devices, biventricular pacemaker and biventricular assist devices. CARDIOSIM© is used in clinical and educational environment.

This paper proposes a lightweight joint with bamboo culm cross connection, which is constructed by screwing one side of the screw into the other side of the wooden plug, its simple construction makes it easy to manufacture and cost-effective. This form connects adjacent bamboo culms to form corner joints, and bolt connects adjacent bamboo culm frames to form edge joints, to explore the mechanical properties of the combination joints formed by corner joints and edge joints, by combining experiments and numerical simulations, the method discovered and explained the relationship and mechanism between the number and position of bolts and the stiffness of edge joints. A calculation model for frame-unit bamboo culm members considering semi-stiffness of joints is proposed, and the conversion equations between linear stiffness of corner and edge joint and their rotational stiffnesses are derived. By establishing the series and parallel relationship between the corner and edge joints in the assembled members, a generalized relational equation between the total stiffness of the assembled joint and the stiffness of the corner and edge joints is derived. A numerical simulation method for frame-unit bamboo culm members with semi-rigid joints is proposed, which can obtain the stiffness calculation formula of edge joints and the average rotational stiffness value of semi-rigid corner joints. A finite element analysis method based on semi-rigid joints is proposed for frame-unit bamboo culm members, and the internal force sketches and calculation methods for bamboo culms and joints are presented, which can be used for the internal force analysis and design of frame-unit bamboo culm lattice structures.

Aluminium bronzes possess a unique combination of high strength and wear and corrosion resistance in aggressive environments; thus, these alloys find wide application in marine, shipbuilding, aviation, railway, offshore platform applications and other fields. Iron-aluminium bronzes (IABs) are the cheapest and most widely used. When the aluminium content is above 9.4 wt%, IAB is biphasic (i.e. it undergoes -transformation) and can be subjected to all heat-treatment types depending on the desired operating behaviour of the bronze component. This article presents correlations (mathematical models) between the primary mechanical characteristics (yield limit, tensile strength, elongation, hardness and impact toughness) and the ageing temperature and time of quench at 920°C in water Cu-11Al-6Fe bronze, obtained using the centrifugal casting method. The microstructure evolution was evaluated depending on the ageing temperature and time changes. Overall, the research was conducted in three successive inter-related stages: a one-factor-at-a-time study, planned experiment, and optimisations. Four optimisation tasks, which have the greatest importance for practice, were formulated and solved. The defined multiobjective optimisation tasks were solved by searching for the Pareto-optimal solution approach. The decisions were made through a nondominated sorting genetic algorithm (NSGA-II) using QstatLab. The optimisation results were verified experimentally. Additional samples were made for this purpose, quenched at 920°C in water and subjected to subsequent ageing with the optimal values of the governing factors (ageing temperature and time) for the corresponding optimisation task. The comparison of the results for the mechanical characteristics with the theoretical optimisation results presents good agreement.

Objectives: There are limited data regarding the efficacy of methylprednisolone in patients with acute respiratory distress syndrome (ARDS) due to coronavirus disease 2019 (COVID-19) requiring invasive mechanical ventilation. We aimed to determine whether methylprednisolone increases the number of ventilator-free days (VFDs) among these patients. Design: Retrospective single-center study Setting: Intensive care unit Patients: All patients with ARDS due to confirmed SARS-CoV-2 infection and requiring invasive mechanical ventilation between 1 March and 29 May 2020 were included Interventions: None Measurements and Main Results: The primary outcome was ventilator-free days (VFDs) during the first 28 days, defined as being alive and free from mechanical ventilation. The primary outcome was analyzed with competing-risks regression based on Fine and Gray’s proportional subhazards model. Death before day 28 was considered to be the competing event. A total of 77 patients met the inclusion criteria. Thirty-two patients (41.6%) received methylprednisolone. The median dose was 1 mg.kg-1 (IQR: 1-1.3 mg.kg-1) and median duration of 5 days (IQR:5-7 days). Patients who received methylprednisolone had a mean 18.8 VFDs (95% CI, 16.6-20.9) during the first 28 days vs. 14.2 VFDs (95% CI, 12.6-16.7) in patients who did not receive methylprednisolone (difference, 4.61; 95% CI, 1.10-8.12; P = 0.001). In the multivariable competing-risks regression analysis and after adjusting for potential confounders (ventilator settings, prone position, organ failure support, severity of the disease, tocilizumab, and inflammatory markers), methylprednisolone was independently associated with a higher number of VFDs (subhazards ratio: 0.10, 95%CI: 0.02-0.45; p=0.003). Hospital mortality did not differ between the two groups (31.2% vs. 28.9%, p=0.82). Hospital length of stay was significantly shorter in the methylprednisolone group (24 days [IQR:15-41 days] vs. 37 days [IQR:23-52 days], p=0.046). The incidence of positive blood cultures was higher in patients who received methylprednisolone (37.5% vs. 17.8%, p=0.052). However, 91% of patients who received methylprednisolone also received tocilizumab. The number of days with hyperglycemia was similar in the two groups. Conclusions: Methylprednisolone was independently associated with increased VFDs and shortened hospital length of stay. The combination of methylprednisolone and tocilizumab was associated with a higher rate of positive blood cultures. Further trials are needed to evaluate the benefits and safety of methylprednisolone in moderate or severe COVID-19 ARDS.

During mechanical ventilation, a disparity between flow, pressure or volume demands of the patient and the assistance delivered by the mechanical ventilator often occurs. Asynchrony effect and ventilator performance are frequently studied from ICU datasets or using commercially available lung simulators and test lungs. This paper introduces an alternative approach of simulating and evaluating patient-ventilator interactions with high fidelity using the electro-mechanical lung simulator xPULM™ under selected conditions. The xPULM™ approximates respiratory activities of a patient during alternating phases of spontaneous breathing and apnoea intervals while connected to a mechanical ventilator. Focusing on different triggering events, volume assist-controlled (V/A-C) and pressure support ventilation (PSV) modes were chosen to test patient-ventilator interactions. In V/A-C mode a double-triggering was detected every third breathing cycle leading to an asynchrony index of 16.67%, being classified as severe. This asynchrony causes a major increase of Peak Inspiratory Pressure PIP = 12.80 ± 1.39 cmH2O and Peak Expiratory Flow PEF = -18.33 ± 1.13 L/min when compared to synchronous phases of the breathing simulation. Additionally, events of premature cycling were observed during PSV mode. In this mode, the peak delivered volume during simulated spontaneous breathing phases almost doubles compared to apnoea phases. The presented approach demonstrates the possibility of simulating and evaluating disparities in fundamental ventilation characteristics caused by double-triggering and premature cycling under V/A-C and PSV ventilation modes. Various dynamic clinical situations can be approximated and could help to identify undesired patient-ventilation interactions in the future. Rapidly manufactured ventilator systems could also be tested using this approach.

Despite chronic fibrosis and associated excess extracellular matrix (ECM) deposition and crosslinking occurring in many pathological conditions, few in vitro studies examine how fibrosis-induced ECM stiffening impacts lymphatic endothelial cells (LEC) behavior and subsequent new lymphatic vessel growth and function. This study examined the stiffening profile of PhotoCol®—commercially available methacrylated type I collagen—photo-crosslinked with photoinitiators Lithium phenyl-2,4,6-trimethylbenzoylphosphinate (LAP), Irgacure 2959 (IRG), and Ruthenium/Sodium Persulfate (Ru/SPS) prior to evaluating PhotoCol® permeability and LEC response to PhotoCol® at low and high stiffness levels representing normal and fibrotic ECM stiffness. Ru/SPS produced the highest maximum stiffness for photo-crosslinked PhotoCol® hydrogels. While Ru/SPS stiffness values did not differ significantly with increased light exposure, permeability decreased significantly with increasing light exposure for 40 kDa dextran. Finally, LECs on softer PhotoCol® appeared smaller with less prominent VE-Cadherin (cell-cell junction) and F-actin expression compared to cells on stiffer PhotoCol®. Overall, PhotoCol® with Ru/SPS photoinitiator provides the fibrillar microstructure and dynamic stiffness range that enables systematic study of LEC stiffness responses relevant to the stiffened ECM observed in pathologies with significant fibrotic activity. Therefore, this study demonstrates the utility of PhotoCol® with Ru/SPS for disease modeling applications, particularly modeling lymphatic vascular growth and function during fibrosis.

In this study, the effect of laser processing (LP) on the thermoelectric (TE) properties of bismuth antimony telluride (BST) alloy pellets is investigated. The stoichiometric alloy used is Bi0.4Sb1.6Te3.0, which was prepared by mechanical alloying techniques (MA) and hot pressed (HP) into pellets under optimal pressing and temperature conditions. An innovative approach to HP was also developed to enhance the yield of BST samples per HP process while maintaining the TE profiles of the samples within a variance of less than 1%. The LP process was executed by employing a metal 3D printer, with a thorough analysis of beam parameters. Notably, the laser power (P) was held constant at 25 W, along with a fixed hatching distance (HD) of 50 μm, while the parameter adjusted was the laser's scanning speed (SS), which spanned from [600 - 1800] mm/s in increments of 200 mm/s. Examination via scanning electron microscopy (SEM) revealed two material states: melted and sintered. The melted state formed the surface crust of "canyon" patterns that were held on the surface of the samples, and which both size and quantity were altered with changes in SS. For thermoelectric characterization, two distinct shapes of LP samples were produced: rectangular (for electrical properties) and disk (for thermal properties). The results demonstrated that the electrical properties are profoundly influenced by SS, with the electrical conductivity peak at SS value of 1600 mm/s, while the Seebeck coefficient reaches a minimum at the same value. Consequently, within the temperature range of interest, a notable 12% increase in electrical conductivity and a 9% decrease in the Seebeck coefficient were observed compared to the non-LP material state. Overall, the ZT value experience an 6.9% decline within the same temperature interval.

To accurately identify high-quality functional wood with superior mechanical properties and enhance its durability, it is imperative to understand the relationships between the physical and mechanical attributes of diverse wood types. Presently, there exist issues related to accuracy, efficiency, and differentiation in studying these performance correlations. The Liang Kleeman (L-K) information flow theory, a causative analytical approach rooted in fundamental physics principles, offers swift computational capabilities. Furthermore, the coefficient of variation in L-K information flow quantitatively gauges the intensity of causal effects. Therefore, this article adopts a causal artificial intelligence perspective and introduces a wood performance analysis method based on L-K information flow.This study focuses on four Chinese fir varieties, including fast-growing Chinese fir (YKS), red heart Chinese fir (CSH, XXH), and iron heart Chinese fir (XXT). By computing and comparing variation coefficients of L-K information flow for various physical properties and their impact on mechanical properties, causal relationships between these properties are elucidated. These findings are then applied to predict wood mechanical properties, achieving a remarkable maximum accuracy of 90%.In the future, these findings will prove invaluable for the selection of high-quality wood and for improving the manufacturing process to prolong the service life of functionalized wood.

The initiation of micro-cracks in concrete is primarily due to its brittleness, which causes severe impacts on the overall behavior of the concrete. However, incorporating fibers in concrete could significantly improve its mechanical properties. The current study demonstrates the influence of two types of fibers on the mechanical properties of concrete. Nylon Fiber Threads (NFT) and Nylon Fiber Strands (NFS) at a fiber content of 2.5 kg/m³ were incorporated in the concrete mix. Concrete with a compressive strength of 30 MPa and a water-cement ratio of 0.4 was produced to investigate the fresh and mechanical properties of conventional and nylon-fiber reinforced concrete (NFRC). The concrete prims and cylinders were tested for compressive, splitting, and flexural strength using ASTM standards (ASTM C-39, C-496, and D-790, respectively). It was found that NFT-reinforced samples achieved higher mechanical properties of concrete (13.05%) compared to NFS-reinforced samples. Test results showed that incorporation of nylon fibers (NF) in concrete decreased the compressive strength of cylindrical and cubical specimens by 0–10% and 5–15%, respectively. However, it increased the splitting tensile and flexural strengths by 0-15%, and 5-15% respectively. Furthermore, the incorporation of NF in concrete significantly improved the ductility and delayed the crack initiation in concrete.

Modular high-rise buildings frequently adopt cast-in-place concrete to ensure building integrity. To reduce the material consumption and realize mold-free casting, a 30 mm thick light concrete mold shell wall panel ( MiC wall panel) is set as part of the shear wall. But the concrete casting process is prone to cracking and rising pattern. Its force performance and damage mechanism is not clear. To this end, this paper designs three groups of MiC wall panels with different material component types. The static load test is carried out in a graded partitioned loading mode. The effects of different material components on the mechanical properties of MiC wall panels are systematically investigated and parametrically analyzed by numerical simulation. The results show that the front cracks of the wall slab are mainly distributed under the truss tendons, and the back cracks are mainly distributed in the span position of the adjacent truss tendons. They are both along the span direction of the wall slab. Increasing the strength level of concrete and using steel fiber concrete can improve the mechanical properties of MiC wall panels to different degrees. Among them, increasing the concrete strength has a significant effect on improving the load-bearing capacity of wall panels, while incorporating steel fibers can significantly improve the deformation and crack resistance of wall panels. By building more finite element models, it was verified that the steel fiber admixture has limited effect on the mechanical properties of wall panels as the concrete grade increases. This study aims to summarize the types of wall panels with the best working properties. It provides a practical basis for optimizing the production and fabrication process of MiC wall panels.

Currently, synthetic diamonds are finding new applications. Quantum devices can be created based on diamond plates with the desired concentration of defects in the structure of the crystal lattice. NV color centers can be used in quantum applications by irradiating plates with high-energy particles, followed by annealing at temperatures above 800°C to develop the spin-optical properties of the centers Diamond plates are subjected to electron irradiation and much less often to proton irradiation. As a result, synthetic diamond plates with NV centers ob-tained by proton irradiation are less studied, although proton irradiation makes it possible to obtain a layered structure of NV centers. In this work, single crystal diamond plates irradiated with protons were studied using polarization microscopy, IR spectroscopy and ODMR spectros-copy. It is shown that when creating NV centers, the distribution and concentration of C – defects in the sample, as well as mechanical stresses before and after irradiation (with subsequent an-nealing), can differ significantly from each other.

There is rapidly emerging evidence from pre-clinical studies, patient samples and patient subpopulations that certain chemotherapeutics inadvertently produce prometastatic effects. Prior to this, we showed that doxorubicin and daunorubicin, stiffen cells before causing cell death, predisposing the cells to clogging and extravasation, the latter being a step in metastasis. Here, we investigate which other anti-cancer drugs might have similar prometastatic effects by altering the biophysical properties of cells. We treat myelogenous (K562) leukemic cancer cells with the drugs nocodazole and hydroxyurea, and then measure their mechanical properties using the microfluidic microcirculation mimetic (MMM) device, which mimics aspects of blood circulation and enables the measurement of cell mechanical properties via transit times through the device. We also quantify the morphological properties of cells to explore biophysical mechanisms underlying the MMM results. Results from MMM measurements show that nocodazole- and hydroxyurea-treated K562 cells exhibit significantly altered transit times. Nocodazole caused significant (p < 0.01) increase in transit times, implying a stiffening of cells. This work shows the feasibility of using the MMM to explore possible biophysical mechanisms that might contribute to chemotherapy-induced metastasis. Our work also suggests cell mechanics as a therapeutic target for much needed antimetastatic strategies in general.

In this work, a simple and environmentally friendly process combining low pressure (vacuum) and mechanical compression is proposed to convert recycled polypropylene (PP) foams (28 kg/m3) into low density foams (90-131 kg/m3) having negative tensile and compressive Poisson's ratios (NPR). The effect of processing conditions (vacuum time, temperature, and mechanical pressure) was studied. Based on the optimized conditions, the tensile Poisson’s ratio of the resulting auxetic foams reached −1.50, while the minimum compressive Poisson's ratios was −0.32 for the same sample. The foam structure was characterized via morphological analysis (SEM) to determine any changes related to the treatment applied. Finally, tensile and compressive properties (Young's modulus, strain energy, energy dissipation and damping capacity) are also presented and discussed. It was observed that the mechanical properties of the resulting auxetic foams were improved compared to the original PP foam (PP-O) for all tensile properties in terms of modulus (19.9 to 59.8 kPa), strength (0.298 to 1.43 kPa) elongation at break (28 to 77%), energy dissipation (14.4 to 56.3 mJ/cm3) and damping capacity (12 to 19%). Nevertheless, improvements were also observed under compression in terms of energy dissipation (1.6 to 3.6 mJ/cm3) and damping capacity (13 to 19%). These auxetic foams can find applications in sport and military protective equipment, as well as any energy mitigation system.

Abstract: The high entropy alloy (HEA) of equiatomic composition CrNiFeCoMn and with FCC 11 crystal structure was prepared by either induction melting and additive manufacturing with a se- 12 lective laser melting (SLM) process, starting from mechanically alloyed powders. Unlike induction 13 melting, the as-produced SLM alloy showed fine nitride and Cr-rich s phase precipitates. Mechan- 14 ical spectroscopy measurements were performed on specimens cold worked and/or recrystallized. 15 Young’s modulus values of (140±10) GPa and (90±10) GPa were measured at 300 K for induction 16 melted and SLM samples, respectively. The values increased to (160±10) GPa and (170±10) GPa for 17 recrystallized samples. Damping measurements as a function of temperature showed two peaks 18 which were attributed to dislocations bending and grain boundaries sliding. The peaks were super- 19 posed on a temperature increasing background.

The high Nb-containing TiAl-based alloy ingot beyond laboratory scale with a composition of Ti-46Al-8Nb (at. %) was prepared by a vacuum induction melting process based on BaZrO3 refractory. An ingot without macroscopic casting defects (such as pipe shrinkage and center line porosity) was finally obtained, and the chemical composition, solidification path, microstructure and tensile properties of the ingots were investigated. The results show that the deviations of Al and Nb content along a 430 mm long central part of the ingot are approximately \mathrm{\pm}0.39 at. % and \mathrm{\pm}0.14 at. %, and the oxygen content in the ingot can be controlled at around 1000 ppm. During the solidification process, the alloy suffered from peritectic reaction and formed columnar grains with anisotropy. In addition to Al segregation and Nb segregation, β-phase particles associated with γ phase at the triple junction of the colonies were observed. Moreover, the mechanical properties of the ingot in the transverse direction are significantly better than those in the longitudinal direction, with a tensile strength of up to high as 700 MPa and a corresponding fracture elongation of 1.1 %.

This paper is part of a study of earthen mixtures for 3D printing of buildings. To meet the ever-growing environmental needs, the focus of the paper is on a particular type of biocomposite for the stabilization of earthen mixtures—the rice husk-lime biocomposite—and on how to enhance its effect on the long-term mechanical properties of the hardened product. Having assumed that the shredding of the vegetable fiber is precisely one of the possible ways to improve the mechanical properties, we compared the results of uniaxial compression tests performed on cubic specimens made with both shredded and unaltered vegetable fiber, for three curing periods. The results showed that the hardened earthen mixture is not a brittle material in the strict sense, because it exhibits some peculiar behaviors, anomalous for a brittle material. However, being a “designable” material, its properties can be varied with a certain flexibility to get as close as possible to the desired ones. One of the peculiar properties of the hardened earthen mixture deserves further investigation, rather than corrections. This is the vulcanization that occurs (in a completely natural way) in the long term, thanks to the mineralization of the vegetable fiber by carbonation of the lime.

In this work, the ternary titanium, copper and silver (Ti-Cu-Ag) system is investigated as a potential candidate for the production of mechanically robust biomedical thin films. The coatings are produced by physical vapor deposition-magnetron sputtering (MS-PVD). The composite thin films are deposited on a silicon (100) substrate. The ratio between Ti and Cu was approximately kept one, with the variation of the Ag content between 10 and 35 at.%, while the power on the targets is changed during each deposition to get the desired Ag content. Thin film characterization is performed by x-ray diffraction (XRD), nanoindentation (modulus and hardness) and Atomic force microscopy to determine the surface topography. The residual stresses are measured by focused ion beam and digital image correlation method (FIB-DIC). The produced Ti-Cu-Ag thin films appear to be smooth, uniformly thick and exhibit amorphous structure for the Ag contents lower than 25 at.%, with a transition to partially crystalline structure for higher Ag concentrations. The Ti-Cu control film shows higher values of 124.5 GPa and 7.85 GPa for modulus and hardness respectively. There is a clear trend of continuous decrease in the modulus and hardness with the increase of Ag content, as lowest value of 105.5 GPa and 6 GPa for 35 at.% Ag containing thin films. In particular, a transition from the compressive (-36.5 MPa) to tensile residual stresses between 229 MPa and 288 MPa are observed with an increasing Ag content. The obtained results suggest that the Ag concentration should not exceed 25 at.%, in order to avoid an excessive reduction of the modulus and hardness with maintaining (at the same time) the potential for an increase of the antibacterial properties. In summary, Ti-Cu-Ag thin films shows characteristic mechanical properties that can be used to improve the properties of biomedical implants such as Ti-alloys and stainless steel.

We demonstrate hybrid integration of a lithium niobate microring resonator with a silicon nitride waveguide in the vertical configuration to achieve efficient light coupling. The microring resonator is fabricated on a lithium niobate on insulator (LNOI) substrate using photolithography assisted chemo-mechanical etching (PLACE). A fused silica cladding layer is deposited on the LNOI ring resonator. The silicon nitride waveguide is further produced on the fused silica cladding layer by first fabricating a trench in the fused silica using focused ion beam (FIB) etching for facilitating the evanescent coupling, followed by formation of the silicon nitride waveguide on the bottom of the trench. The FIB etching ensures the required high positioning accuracy between the waveguide and the ring resonator. We achieve Q-factors as high as 1.4*10^7 with the vertically integrated device.

Periodontitis is microbial infection affecting periodontium, the tooth supporting structure and affects >743 million people worldwide. Neural crest-derived stem cells (NCSCs) hold the promise to regenerate the damaged periodontium. These cells have been identified within adult adipose tissue, periodontal ligament, and palatal tissue. Typical enzymatic isolation protocols are expensive, time consuming and often not clinically compliant. Enzyme-free, mechanical dissociation has been suggested as an alternative method of generating cell suspensions required for cell separation and subsequent expansion ex vivo. In our study, samples of rat skeletal muscle tissue were used to appraise the suitability of a novel mincing method of mechanical dissociation against enzymatic digestion with collagenase and dispase. Skeletal muscle is readily available and has been shown to contain NCSC populations. We used a Rigenera-Human Brain Wave^® prototype mincer to produce a suspension of skeletal muscle-derived cells modeling NCSCs. We have compared the resulting cell cultures produced via mechanical dissociation and enzymatic dissociation, producing single cell suspensions suitable for Magnetic Cell Sorting (MACs) and Fluorescence-activated cell sorting (FACS). Despite the Countess Automated Cytometry data demonstrating that cell suspensions produced by mechanical dissociation (n=24) contain on average 26.8 times as many viable cells as enzymatic cell suspensions (n=18), enzymatic suspensions produced more successful cell cultures. Spheroids and subsequently adherent cells formed from 4 enzymatic cell suspensions (44.4%) vs. 1 mechanical cell suspension (8.3%). Enzymatic digestion protocols formed spheroids faster and more plentifully than mechanical cell suspensions. Adherent cells and spheroids isolated via both methods appear morphologically similarly to NCSCs from our previous studies.

Current study aims to evaluate the possibilities to increase part strength by optimizing the FFF process parameters. Five different CAD models of parts with same coupling dimensions but different shape inherited from a recent study were converted into test samples with Ultimaker 2 3D printer. The main measure of success was the sample strength, defined as the load at which the first crack in the stressed area of the part appeared. Three different modifications to the FFF process with verified positive effect on interlayer bonding were applied. First modification included raising the extrusion temperature and disabling printed part cooling. Second modification consisted in reduction of the layer thickness. Third modification combined the effects of the first and the second ones. For four out of five shapes tested applied process modifications resulted in significant strengthening of the part. The shape that exhibited the best results was subject to further research by creating special printing mode. The mode included fine-tuning of three technological parameters on different stages of the part fabrication. As result it was possible to increase the part strength by 108% only by tuning printing parameters of the best shape designed with increasing its weight by 8%.

The increased consumption of food requiring thermoformed packaging means that the packaging industry demands customized solutions in terms of shapes and sizes to make the packaging unique. In particular, the food industry increasingly requires more transparent packaging, with greater clarity and a better presentation of the product features they contain. However, in turn, the differentiation of products is sought through the geometry and final finish of the product, as well as the arrangement of food inside the packaging. In addition, these types of packaging usually include ribs in the walls to improve physical properties, however they also affect the final aesthetics of the product. In accordance with this, this research study analyses by studying the mechanical properties of different relief geometries that can affect not only the aesthetics but also their strength. For this purpose, tensile and compression tests have been carried out. The results provide comparative data on the reliefs studied and show that there are different shapes, sizes and layout.

Transparent electrodes (TEs) made of metallic nanowires, such as Ag, Au, Cu, and Ni, have attracted rising attention for several reasons: 1) they can act as a substitute for tin oxide-based TEs such as indium-tin oxide (ITO) and fluorine-doped tin oxide (FTO); 2) various methods exist for fabricating such TEs such as filtration, spraying and meyer bar coating; 3) greater compatibility with different substrates can be achieved due to the variety of fabrication methods; and 4) extra functions in addition to serving as electrodes, such as catalytic abilities, can be obtained due to the metals that compose the TEs. There are a large number of applications for TEs, ranging from electronics and sensors to biomedical devices. This short review is a summary of recent progress, mainly during the past five years, on silver nanowire-based TEs. The focus of the review will be on theory development, mechanical, chemical and thermal stability and optical properties. The many applications of TEs are outside the scope of this review.

A technique for fabrication of bacterial cellulose-based films with CeO₂ nanofiller has been developed. The structural and morphological characteristics of the materials have been studied, their thermal and mechanical properties in dry and swollen states having been determined. The preparation methodology makes it possible to obtain composites with a uniform distribution of nanoparticles. The catalytic effect of ceria regarding the thermal oxidative destruction of cellulose has been confirmed by TGA and DTA methods. An increase in CeO₂ content led to an increase in the elastic modulus (a 1.27-fold increase caused by the introduction of 5 wt.% of the nanofiller into the polymer) and strength of the films. This effect is explained by the formation of additional links between polymer macro-chains via the nanoparticles’ surface. The materials fabricated were characterised by a limited ability to swell in water. Swelling caused a 20- to 30-fold reduction in the stiffness of the material, the mechanical properties of the films in a swollen state remaining germane to their practical use. The application of the composite films in cell engineering as substrates for the stem cells’ proliferation has been studied. The increase in CeO₂ content in the films enhanced the proliferative activity of embryonic mouse stem cells. The cells cultured on the scaffold containing 5 wt.% of ceria demonstrated increased cell survival and migration activity. An analysis of gene expression confirmed improved cultivation conditions on CeO₂-containing scaffolds.

A typical halogen-free flame-retardant (HFFR) formulation for electric cables may contain polymers, various additives, and fire-retardant fillers. In this study, composites are prepared by mixing natural magnesium hydroxide (n-MDH) with linear low-density polyethylene (LLDPE) and a few types of ethylene-octene copolymers (C₈-POE). Depending on the content of LLDPE and C₈-POE, we obtained composites with different crystallinity that affected the final mechanical properties. The nucleation effect of the n-MDH and the variations in crystallinity caused by the blending of C₈-POE/LLDPE/n-MDH were investigated. In the C₈-POE/LLDPE blend, we found a decrease in the crystallization temperature of LLPDE compared to pure LLDPE and an increase in the crystallization temperature of C₈-POE compared to pure C₈-POE. On the contrary, the addition of n-MDH led to an increase in the crystallization temperature of LLDPE. As expected, the increase in the crystallinity of the polyolefin matrix of composites led to higher elastic modulus, higher tensile strength, and lower elongation at break. Overall, these results show how to obtain the required mechanical features for halogen-free flame-retardant compounds for electric cable applications depending on the quantities of the two miscible components in the final blend.

The design of biomaterial platforms able to release bioactive molecules is mandatory in tissue repair and regenerative medicine. In this context, electrospinning is a user-friendly, versatile and low-cost technique, able to process different kinds of materials in micro- and nano-fibers with a large surface area-to-volume ratio for an optimal release of gaseous signalling molecules. Recently, the antioxidant and anti-inflammatory properties of the endogenous gasotramsmitter hydrogen sulfide (H2S), as well as its ability to stimulate relevant biochemical processes on the growth of mesenchymal stem cells (MSC), have been investigated. Therefore, in this work, new poly(lactic) acid fibrous membranes (PFM), doped and functionalized with H2S slow-releasing donors extracted from garlic, were synthetized. These innovative H2S-releasing mats were characterized for their morphological, thermal, mechanical and biological properties. Their antimicrobial activity and effects on the in vitro human cardiac MSC growth, either in the presence or in the absence of oxidative stress, were here assessed. On the basis of the results here presented, these new H2S-releasing PFM could represent promising and low-cost scaffolds or patches for biomedical applications in tissue repair.

In the paper, a study of the performance of unmanned ground vehicle (UGV), establishes numerical simulation model of the chassis system by three-dimensional software and finite element analysis software. Based on the numerical modelling and analysis, the work focuses on study of the strength and stiffness of the vehicle's chassis and researched the distribution of stress and deformation under the extremal condition. The paper also presents an autopilot design with new cascade control system for an autonomous motion of an unmanned ground vehicle based on Proportional-Integral-Derivative (PID) and Feed-Forward (FF) control. The PID-FF controller is a part of dedicated for presented UGV used in a hybrid control system for precise control and stabilization, necessary to increase the vehicle motion stability and maneuvers precision. The hybrid PID-FF control system proposed for the ground vehicle model gives a satisfactory quality of control, while maintaining the simplicity of the control system. Presented tests performed in area of mechanical design and control analysis gives good results and proves usefulness of designed unmanned device.

Egg activation is a cellular transition of an arrested mature oocyte into a developing embryo through a coordinated series of events. Previous studies in Hymenoptera have indicated that mechanical pressure can induce egg activation. In this study, we developed the first egg activation protocol for the haplodiploid insect pest, Sirex noctilio (Hymenoptera: Siricidae), from two climatically different regions in South Africa. In addition, activated eggs were exposed to three treatments involving water, pine sawdust, and the fungal symbiont of S. noctilio, Amylostereum areolatum (Russulales: Amylostereaceae), to confirm the hypothesised prerequisite of the symbiotic fungus for egg development. A rearing protocol was developed for emerged first instar larvae using a modified Anoplophora glabripennis (Coleoptera: Cerambycidae) artificial diet. A significant difference between mean survival rates of activated eggs from the two different regions was observed. Amylostereum areolatum was shown to be unnecessary for egg survival and adversely affected egg eclosion. Maximum larval survival duration on the artificial diet was 92 days. The egg activation and rearing protocol developed in this study enables opportunities for research on the physiology, ecology, symbioses, and genetics of S. noctilio, which can be exploited for new genetic pest management strategies.

Background: Osteoclastic bone resorption in the compression zone of periodontal ligament (PDL) plays a role in orthodontic tooth movement, and is regulated by the balance of RANKL and OPG. Compression downregulates OPG, conversely, tension upregulates OPG in PDL cells. However, the regulatory mechanism of OPG expression in PDL cells under different mechanical stresses remains unclear. Methods: To study microRNA (miRNA) expression profiles, compression (2g/cm²) or tension (15%-elongation) was applied to immortalized human PDL (HPL) cells, and miRNA was extracted. The miRNA expression was analyzed using a human miRNA microarray, and the changes of the miRNA expression were confirmed by real-time RT-PCR. In addition, miR-3198-mimic and -inhibitor were transfected into HPL cells to understand the resulting OPG expression and production. Results: Certain miRNAs were expressed differentially under compression and tension. Some miRNAs including miR-3198 were upregulated only by compression. Real-time RT-PCR confirmed that compression induced miR-3198, but tension reduced it, in HPL cells. miR-3198-inhibitor upregulated and miR-3198-mimic reduced OPG in HPL cells. miR-3198-inhibitor rescued the compression-mediated downregulation of OPG. On the other hand, miR-3198-mimic reduced OPG expression under tension. Conclusion: We conclude that miR-3198 is upregulated by compression and is downregulated by tension, suggesting that miR-3198 downregulates OPG in response to mechanical stress.

The composite post insulator composed of a large diameter mandrel and flange pressed by one-time integral pultrusion has high strength and good toughness, widely used in the existing flexible converter valve. For constructing the finite element model of the crimped post insulator, most of the flange surface and the mandrel surface are directly connected, making the simulation model's stiffness deviate from the actual model and the model distortion. Based on this, this study proposes a new finite element simplified model of crimped composite post insulator based on Multi-Point Constraints (MPC), which accurately simulates the crimping area of man-drel and flange in engineering practice. It verifies the model's reliability through static tests and characteristic vibration tests. The results show that the difference between the finite element simulation and test results is within 5 %. The finite element modeling method based on MPC local constraints is very reliable in applying crimped composite post insulators. Based on the proposed model, the influence of flange height and thickness on the mechanical properties of composite post-insulators is further explored. The results show that the influence of flange height on mechanical properties can be ignored when the height of the insulator stiff-ener ( non-press common area ) is constant. Within the allowable thickness range of the flange crimping process, the increase in flange thickness will significantly reduce the maximum bend-ing stress of the insulator and increase its safety margin. It provides a good design idea for the design of crimping composite insulators.

Metal additive manufacturing technologies have large potential for future use in load bearing aerospace applications, requiring a deeper understanding of mechanical performance and influencing factors. The objective of this study is to manufacture fatigue specimens by laser powder bed fusion with comparable bulk and different as-built surface quality (without post-processing). This goal was pursued by using identical bulk/hatch scan parameters while varying contour scan parameters. The bulk quality was evaluated by density measurements according to Archimedes’ principle and tensile testing. The surfaces were investigated using the optical fringe projection method and surface quality was assessed by the areal surface texture parameters Sa (arithmetic mean height) and Sk (core height, derived from material ratio curve). The resulting mean values of max (ultimate tensile strength) were between 375 and 405 MPa, which is a variation of roughly 8%, for seven different surface conditions. It could be confirmed that the influence of contour scan variation on bulk quality is insignificant for the assessed samples.

In a dual-inertia system based on permanent magnet synchronous motor (PMSM), the elastic transmission mechanism, such as reducer and coupling, is prone to mechanical resonance, which reduces the precision of servo system transmission. Model prediction and introduction of state feedback are effective methods to suppress mechanical resonance, but the control parameters de-pend on the mechanical parameters of the system. Therefore, mechanical parameter identification is very necessary. In this paper, a forgetting factor recursive least square method is used to identify the mechanical parameters of the dual-inertia elastic system. Firstly, the mathematical model of the dual-inertia system is established and reasonably simplified. Then, the discrete function of the identification algorithm is constructed, and the motor speed and electromagnetic torque are sam-pled to achieve the on-line identification of the main mechanical parameters of the dual-inertia system, and the influencing factors of the identification accuracy are analyzed. Finally, simulations and experiments are carried out to verify the effectiveness of the algorithm.

This paper is a study of a generalization of the quantum Riemannian Hamiltonian evolution, previously analyzed by us in our work [6], in the geometrization of quantum mechanical evolution in a Finsler geometry. We find results with dynamical equations governing the evolution of the trajectories defined by the expectation values of position. The analysis appears to provide an underlying geometry described by a geodesic equation, with connection form with a second term which is an essentially quantum effect. These dynamical equations provide a new geometric approach to the quantum evolution where we suggest a definition for "local instability" in the quantum theory.