The geometry of Poincare disk itself is interpreted without any mapping to dierent spaces. Our approach might be one of the shortest and is intended for educational contribution.

Three-temperature heating systems consist of a heat engine and a heat pump, enabling thus maximum usage of the primary thermal source for the heating of buildings. This analysis has revealed obvious advantages and disadvantages that the combining of thermodynamic systems has in future development, also with respect to environmental and economic issues. It appears that the combination of a Stirling engine or a similar heat drive with a heat pump is especially suitable. In order to analyze the effectiveness of such a system, a comprehensive calculation procedure is used: its basis lies in accounting for all types of energy and their relationship to the original natural resource. The present paper aims to point out that the combination of Stirling engine and a heat pump is a useful solution thanks to the most favorable resultant economic impact if compared to the usage of a diesel, four-stroke gas, or, most commonly used, electric drive.

Molecular overtone transitions provide optical frequency transitions sensitive to variation in the proton-to-electron mass ratio (μ = m_p/m_e). However, robust molecular state preparation presents a challenge critical for achieving high precision. Here, we characterize infrared and optical-frequency broadband laser cooling schemes for TeH⁺, a species with multiple electronic transitions amenable to sustained laser control. Using rate equations to simulate laser cooling population dynamics, we estimate the fractional sensitivity to μ attainable using TeH⁺. We find that laser cooling of TeH⁺ can lead to significant improvements on current μ variation limits.

Citrullinemia is the earliest identifiable biochemical abnormality in neonates with intrahepatic cholestasis due to a citrin deficiency (NICCD) and it has been included in newborn screening panels using tandem mass spectrometry. However, only one neonate was positive among 600,000 infants born in Sapporo city and Hokkaido, Japan between 2006 and 2017. We investigated 12 neonates with NICCD who were initially considered normal in newborn mass screening (NBS) by tandem mass spectrometry, but were later diagnosed with NICCD by DNA tests. Using their initial NBS data, we examined citrulline concentrations and ratios of citrulline to total amino acids. Although their citrulline values exceeded the mean of the normal neonates and 80 % of them surpassed +3SD, all were below the cutoff of 40 nmol/mL. The ratios of citrulline to total amino acids significantly elevated in patients with NICCD compared to the control. By evaluating two indicators simultaneously, we could select about 80% of patients with missed NICCD. Introducing an estimated index comprising citrulline values and citrulline to total amino acid ratios could assure NICCD detection by NBS.

The main objective of this paper is to find a close link between the adaptive level of significance, presented here, and the sample size. We, statisticians, know of the inconsistency, or paradox, in the current classical tests of significance that are based on p-value statistics that is compared to the canonical significance levels (10%, 5% and 1%): "Raise the sample to reject the null hypothesis" is the recommendation of some ill-advised scientists! This paper will show that it is possible to eliminate this problem of significance tests. The Bayesian Lindley's paradox – "increase the sample to accept the hypothesis" – also disappears. Obviously, we present here only the beginning of a possible prominent research. The intention is to extend its use to more complex applications such as survival analysis, reliability tests and other areas. The main tools used here are the Bayes Factor and the extended Neyman-Pearson Lemma.

Spectral photon counting cone-beam CT imaging is challenged by individual pixel response behaviour, which leads to noisy projection images and subsequent image artefacts like rings. Existing methods to correct for this either use calibration measurements, like signal-to-thickness calibration (STC), or perform post-processing ring artefact correction of sinogram data or scan reconstructions, without taking the pixel response explicitly into account. Here we present a novel post-processing method (DAC-shifting), which explicitly measures the current pixel response using flat field images, and subsequently corrects the projection data. The DAC-shifting method was evaluated with a repeat series of spectral photon counting imaging (Medipix3) of a phantom with different density inserts, and in iodine K-edge imaging. The method was also compared against PMMA based STC. The DAC-shifting method was shown to be effective in correcting individual pixel response, and was robust against detector instability. On the contrary, STC correction showed varying results, which was almost as good as DAC-shifting when data was acquired just after STC calibration, but worse with larger time differences. In K-edge imaging, DAC-shifting provides a sharper attenuation peak, and more uniform CT values, which is expected to benefit iodine concentration quantification.

Several efforts have been made to estimate the prevalence of different types of antibiotic resistance in different regions of Nigeria. The study investigated the prevalence of Klebsiella pneumoniae encoding genes for CTX-M, TEM, and SHV-1 extended-spectrum beta-lactamases (ESBL) enzymes isolated from urine samples of non-hospitalized patients with suspected UTI in Lagos State, Nigeria. A 4-month retrospective study, spanning from May 2023 to August 2023, was conducted. K. pneumoniae was isolated from urine samples using standard microbiological methods. The modified Kirby-Bauer disc diffusion method was used to test for antibiotic susceptibility, and Clinical and Laboratory Standard Institute (CLSI) guidelines were followed for interpretation. The double-disk synergy method was used to confirm the phenotypic identity of ESBL producers, and the results were interpreted in accordance with CLSI guidelines. The phenotypic method was utilized for ESBL screening, employing the standard disk diffusion method. The CTX-M ESBL gene, TEM gene, and SHV gene were found using multiplex PCR. Results revealed that 41 K. pneumoniae isolates were resistant to third-generation Cephalosporins; the isolates showed resistance to ceftazidime in 100% of cases and ceftriaxone in 80.49% of cases respectively. It was determined that 8 (19.51%) of the isolates produced ESBL. Among Klebsiella isolates, the frequencies of the SHV, TEM, and CTX-M genes were 31 (75.61%), 4 (9.76%), and 10 (24.39%), in that order. Four isolates (9.67%) had the SHV, TEM, and CTX-M genes, while eight (19.51%) of the isolates possessed both the SHV and CTX-M genes. This investigation demonstrates high frequency, wide range of patterns and coexistence of ESBL genes in K. pneumoniae isolates from outpatient UTI patients. Although several phenotypic tests have been used for ESBL detection, testing directly for the presence of ESBL genes is always more accurate. The majority of the isolates of Klebsiella pneumoniae ESBL producers had the SHV gene identified.

In a context of increasingly necessary energy transition, precise modelling of profiles for low-voltage (LV) network consumers is crucial to enhance hosting capacity. Typically, load curves for these consumers are estimated through measurement campaigns conducted by Distribution System Operators (DSO) for a representative subset of customers or through the aggregation of load curves from household appliances within a residence. With the instrumentation of smart meters becoming more common, a new approach to modelling profiles for residential customers is proposed to make the most of the measurements from these meters. The disaggregation model estimates the load profile of customers on a low-voltage network by disaggregating the load curve measured at the secondary substation level. By utilizing only the maximum power measured by Linky smart meters, along with the load curve of the secondary substation, this model can estimate the daily profile of customers. For 48 secondary substations in our dataset, the model obtained an average symmetric mean average percentage error (SMAPE) error of 4.91% in reconstructing the load curve of the secondary substation from the curves disaggregated by the model. This methodology can allow the estimation of the daily consumption behaviors of the low-voltage customers. In this way, we can safely envision solutions that enhance the grid hosting capacity.

The agricultural sector in Palestine has a significant role in its economy. However, the production of this sector is affected by different kinds of plant diseases, specifically leaf diseases. Automatic agricultural leaf disease detection is essential for the early diagnosis and controls the overall health of fields. Image segmentation techniques, clustering, and deep learning are often used to detect diseased leaves. This study proposes a novel hybrid approach based on image classification. The hybrid approach combines the k-means clustering algorithm with Convolutional Neural Network (CNN), where k-means is used to detect the leaf’s infected area, then CNN is used for specifying the disease. We used the PlantVillage dataset for experimental verification as it contains several crops with different kinds of challenging diseases. We also examined the selection of optimal k-value using the Silhouette coefficient, Elbow method, and Kneedle Algorithm. The Silhouette technique was analyzed using three distance metrics; Euclidean, Manhattan, and Cosine. Its scores for the three-distance metrics were low, near-zero, and failed to produce the optimum k value. Besides, the Elbow method was complicated to use in image segmentation in terms of executing and visualizing the k value in its graph plot. Based on verification results, the Kneedle Algorithm produced better results in the consistency of choosing the optimal k value and showed superiority over other approaches. Therefore, the processed images were segmented with the k-means clustering algorithm with a Kneedle algorithm-based k value. Finally, a Convolutional Neural Network (CNN) is trained to classify the type of disease based on analyzing and testing leaf images. The hybrid model achieved high accuracy of 93.79% in disease identification, confirming the proposed model’s robustness.

To determine the metamorphic ages of the accretionary complexes in the Northern Chichibu Belt in SW Japan, K–Ar dating was conducted using weakly metamorphosed sedimentary rocks collected from the Kanto Mountains, Central Japan. Whole-rock ages were obtained for chert and red shale samples, and the mineral ages of fine-grained illite with the grain size less than 4 μm were obtained for chert, red shale, mudstone, acidic tuff, and basic tuff. The K–Ar ages of chert and red shale presented large variations, with systematically older ages compared to those of mudstone and tuff in the same strata. The influence of submarine hydrothermal activities on chert and red shale before subduction is a possible cause of this deviation. The illite samples, which were fractionated into four grain-size classes using a suspension method, yielded older ages and higher illite crystallinity (i.e., smaller values of Kübler’s crystallinity index) for larger grain-size classes. The peak metamorphic ages were determined from the K–Ar ages of the 3–4 μm class illite in mudstone and tuff. The Late Jurassic to the Earliest Cretaceous accretionary complex of the lowest structural unit (Kashiwagi Unit) was dated within a small range between 117–110 Ma, which is distinctly older than the K–Ar ages of white mica reported from the Sanbagawa Belt. The peak metamorphic age of acidic tuff (113 Ma) at the type locality of the Mikabu Greenstones indicates that the subducted Mikabu seamount is a constituent of the Kashiwagi Unit. The peak metamorphic ages of the Manba and Kamiyoshida Units were obtained as 132–107 Ma and 163–144 Ma, respectively. Major structural discontinuity is suggested within the Middle Jurassic accretionary complexes.

BACKGROUND. Two sequelae of non-alcoholic steatohepatitis (NASH), ESLD and HCC, have become the leading causes for liver transplantation in the Western. The present study aims to approach the cellular metabolic disturbances involved in NASH progression that are associated with microbiota community changes. METHODS. Metabolic effects and microbiota community changes were explored in the murine with NASH progression by blocking the Na/K-ATPase/Src/reactive oxygen amplification loop using the synthetic targeting peptide pNaKtide. DNA from the terminal ileum microbiota habitat was obtained and amplified by PCR to develop DNA bacterial phylogenic sequence analysis of wild type and treated animals at 12, 24 and 48 weeks. Induced changes by pSrc normalization at 24 weeks were correlated with liver morphological changes, intestinal CD4+/CD8+ ratio, and liver macrophage CD14+ expression. Differences among groups were evaluated by ANOVA/t-test and Principal Component Analysis (PCA). RESULTS. Microbiota communities varied significantly at all time points (12, 24 and 48 weeks), with an increase of Verrucomicrobia and a decrease of Bacteroidetes and Firmicutes in the HFD group. Microbiota community changes regressed to their wild-type state at 24 weeks on treated animals, and those changes were associated with a decrease in liver inflammation and senescence, lower ileum CD4+/CD8+ T cells and higher liver CD14+ cells (p<0.05). Concomitantly, the metabolic disturbances in our diet-induced NASH model were normalized by NKA/Src signaling blockage and exercise with a paucity of apoptotic activity, mitigation of cell senescence, and regression of liver fibrosis (p<0.01). CONCLUSIONS. pSrc inhibition at caveolar α1-Na/K-ATPase rescinded NASH-related metabolic disturbances establishing resident physiological microbiota communities with concomitant paucity on apoptotic activity and regression of liver fibrosis; effects that were associated with both gut and liver T-lymphocyte responses.

Ubiquitous computing comprises scenarios where networks, devices within the network, and software components change frequently. Market demand and cost-effectiveness are forcing device manufacturers to introduce new-age devices. Also, the Internet of Things (IoT) is transitioning rapidly from the IoT to the Internet of Everything (IoE). Due to this enormous scale, effective management of these devices becomes vital to support trustworthy and high-quality applications. One of the key challenges of IoT device management is automatic device classification with the logically semantic type and using that as a parameter for device context management. This would enable smart security solutions. In this paper, a device classification approach is proposed for the context management of ubiquitous devices based on unsupervised machine learning. To classify unknown devices and to label them logically, a proactive device classification model is framed using a k-Means clustering algorithm. To group devices, it uses the information of network parameters such as Received Signal Strength Indicator (rssi), packet_size, number_of_nodes in the network, throughput, etc. Experimental analysis suggests that the well-formedness of clusters can be used to derive cluster labels as a logically semantic device type which would be a context for resource management and authorization of resources. This paper fulfills an identified need of proactive device classification for device management.

Mints emit diverse scents that exert specific biological functions and are relevance for applications. The current work strives to develop electronic noses that can electronically discriminate the scents emitted by different species of Mint as alternative to conventional profiling by gas chromatography. Here, 12 different sensing materials including 4 different metal oxide nanoparticle dispersions (AZO, ZnO, SnO2, ITO), one Metal-Organic Frame as Cu(BPDC), and 7 different polymer films including PVA, PEDOT: PSS, PFO, SB, SW, SG, PB were used for functionalizing of QCM sensors. The purpose was to discriminate six economically relevant Mint species (Mentha x piperita, Mentha spicata, Mentha spicata ssp. crispa, Mentha longifolia, Agastache rugosa, and Nepeta cataria). The adsorption and desorption datasets obtained from each modified QCM sensor were processed by three different classification models including Principal Component Analy-sis (PCA), Linear Discriminant Analysis (LDA), and k-Nearest Neighbor Analysis (k-NN). This allowed discriminating the different Mints with classification accuracies of 97.2% (PCA), 100% (LDA), and 99.9% (k-NN), respectively. Prediction accuracies with a repeating test measurement reached up to 90.6% for LDA, and 85.6% for k-NN. These data demonstrate that this electronic nose can discriminate different Mint scents in a reliable and efficient manner.

Hyper spectral imaging (HSI) is a technique that is used to obtain the spectrum for each pixel in the image. It helps in finding objects and identifying materials etc. Such an identification is very difficult using other imaging techniques. It allows the researchers to investigate the documents without any physical contact. Nowadays detection of unequal Ink mismatch based on HSI has shown vast improvement in distinguishing the inks. Detection of unequal Ink mismatch is an unbalanced clustering problem. This paper used K-means Clustering for ink mismatch detection. K-means Clustering find same subgroups in the data based on Euclidean distance. This paper demonstrates performance in unequal Ink mismatch based on HSI.

Based on the insight gained from single jet analysis performed earlier [1], CFD analysis on turbulent jets impinging on one another at an angle was performed. Multiple impingement angles were considered for this study to gain better understanding of the parameters affecting resultant jet growth and velocity distribution. From the study of single jet, it was concluded that the SST k-ω turbulence model was the ideal turbulence model capable of accurately predicting the flow physics of the jets exiting a fully developed pipe at low Reynolds number. Hence, for the study of impinging jets, SST k-ω turbulence model was used to study the velocity and jet growth characteristics. It became evident that the mesh alignment with the velocity vector at exit of the pipe domain plays a crucial role in the accuracy of the results. The parameter used to evaluate this condition was identified as False Diffusion and was observed to affect the TKE parameter significantly. Methods to reduce false diffusion are also discussed in this article. Based on the mesh obtained from the grid sensitivity study, jets impinging at 30, 45 and 60 degrees at Reynolds number of 7500 were numerically analyzed. It was observed that the profile of the resultant jet closely matched with the prediction of elliptical profile predicted by past researchers, [2] and [3]. Also, it was seen that higher jet growth was predicted in case of jets impinging at a higher impingement angle.

This paper considers the detection of fluctuating target in heavy-tailed clutter through the use of dynamic programming based on track-before-detect (DP-TBD) in radar systems. The clutter is modeled in terms of K-distribution, which can be widely used to describe non-Gaussian clutter received from high-resolution radars and radars working at small grazing angle. Swerling type 1 is considered to describe the target fluctuation between scans. Conventional TBD techniques suffer from significant performance loss in heavy-tailed environments due to the more frequent occurrences of target-like outliers. In this paper, we resort to DP-TBD algorithm based on prior information, which can enhance the detection performance by using the environment and target fluctuating information during the integration process of TBD. Under non-Gaussian background, the expressions of the likelihood ratio merit function for Swerling type 1 target are derived first. However, the closed analytical form of the merit function is difficult to be obtained. In order to reduce the complexity of evaluating the merit function and the computational load, an efficient approximation method as well as a two-stage detection approach is proposed and used in the integration process. Finally, several numerical simulations of the new strategy and the comparisons are presented to verify that the proposed algorithm can improve the detection performance, especially for fluctuating target in heavy-tailed clutter.

Nowadays, the research and development of on-chip LiDAR sensors for vehicle collision avoidance is growing very fast. Therefore, the assessment of the reliability in obstacle detection using the information provided by LiDAR sensors has become a key issue to be explored by the scientific community. This paper presents the design and implementation of a self-tuning method in order to maximize the reliability of an Internet-of-Things sensors network and to minimize the number of sensors to localize with the required accuracy obstacles by a detection threshold. In order to achieve this goal, models that predict accuracy (i.e., prediction error) for object localization using data collected by LIDAR sensors are designed and implemented in Webots Automobile 3D simulation tool. The approach is based on combining different techniques. Firstly, point-cloud clustering technique and an error prediction model library composed by a multilayer perceptron neural network with backpropagation, k-nearest neighbors and linear regression are explored. Secondly the above-mentioned techniques for modeling are also combined with a supervised and reinforcement machine learning technique, Q-learning in order to minimize the detection threshold. In addition, a IoT driving assistance simulated scenario with a LiDAR sensor network is designed in order to validate the prediction model and the optimal configuration of the sensor network to guarantee reliability in obstacle localization. The results demonstrate that the self-tuning method is appropriate to increase the reliability of the sensor network whereas minimizing the detection threshold

Neck circumference (NC), neck circumference to height ratio (NHtR) and neck circumference to weight ratio (NWtR) appear to be good candidates for the non-invasive management of non-alcoholic fatty liver disease (NAFLD). This study aimed to evaluate the ability of routine variables to assess and manage NAFLD in participants with obesity and NAFLD included in a 2-year nutritional intervention program. Anthropometric measurements, biochemical variables and imaging techniques were performed at different study time-points (baseline, 6, 12 and 24 months). The nutritional intervention significantly improved all anthropometric measurements as well as the glucose profile and the hepatic enzymes. NC and neck ratios combined with ALT levels and HOMA-IR showed good prediction ability for the hepatic fat content and hepatic steatosis at all the study time-points in a ROC analysis. The prediction ability of the combination panels improved when the weight loss variable was also considered. NC and neck ratios are easy anthropometric measurements that in combination with routine biochemical variables (ALT and HOMA-IR) showed good prediction ability of NAFLD. More research studies are necessary to validate the utility of these simple and easy variables as surrogate markers of NAFLD since their application could improve the prevention and management of this prevalent disease.

In order to explore the combustion performance of a non-road air-cooled two-cylinder turbocharged diesel engine, an experiment on the effects of engine compression ratio, combustion chamber shape and injection timing were systematically conducted in this study. Moreover, the effects of intake air conditions on combustion performance were numerically investigated using the one-dimensional simulation platform. The findings of this study could help provide new insights for promoting the sustainable development of diesel engines used in generator sets. The results show that the increase of intake air temperature can delay the combustion center of gravity, and improve the combustion performance and the sustainability of diesel engines. The decrease of intake air pressure will lead to a reduction in oxygen amount during the combustion process, thus causing a deterioration of cylinder pressure and combustion performance. By modifying the combustion chamber, the ignition delay and combustion duration are each extended by 1.6 degrees and 4.2 degrees under 100% engine load. The ignition delay and combustion duration are not obviously affected by modifying the combustion chamber shape under 25% and 50% loads. By increasing the compression ratio from 19.5 to 20.5, the ignition delay and combustion duration are shortened, which could enhance the cylinder pressure and heat release rate. However, reducing the compression ratio from 19.5 to 18.5 could significantly decrease the heat release rate. Under middle and low loads, combustion duration is less affected by injection timing. Under 100% load, the peak cylinder pressure increases to 11.4 MPa, and the ignition delay is shortened by advancing injection timing from -17°CA to -20°CA.

Here, we report an ultrasoft extra long-lasting reusable hydrogel-based sensor that enables high quality electrophysiological recording with low motion artifacts. The developed sensor can be used and stored in the ambient environment for months before being reused again. The developed sensor is made of a self-adhesive electrical-conductivity-enhanced ultrasoft hydrogel, mounted in an Ecoflex-based frame. Hydrogel’s conductivity was enhanced by incorporating polypyrrole (PPy), resulting in the conductivity of 0.25 S m-1. Young’s modulus of the sensor is only 12.9 kPa and it is stretchable up to 190%. The sensor was successfully used for the electrocardiography (ECG) and electromyography (EMG). Our results indicate that using developed hydrogel-based sensor, the signal-to-noise ratio of recorded electrophysiological signals was improved in comparison to that when medical grade silver/silver chloride (Ag/AgCl) wet gel electrodes were used (33.55 dB in comparison to 22.16 dB). Due to the ultra-softness, high stretchability, and self-adhesion of the developed sensor, it can conform to the skin and therefore, it shows low susceptibility to motion artifacts. Also, the sensor shows no sign of irritation or allergic reaction that usually occurs after long-term wearing medical grade Ag/AgCl wet gel electrodes on the skin. Further, the sensor is fabricated using a low cost and scalable fabrication process.

The demand for improved service in mobile networks is always increasing. That means signal transmission with higher capacity is required. To achieve that goal a combined optical and wireless link using double polarization multiplexing has been developed. A high quality signal transmission is achieved by applying high polarization extinction ratio. The new concept is validated by experiments varying the bit rate and fiber length. A signal with 12 Gbit/s bit rate was transmitted over a 25 km long combined link with about 1.10-8 bit error rate. That result is much better than the already published data which were measured on links transmitting information with 2.5 Gbit/s bit rate. The polarization multiplexing technique is very practical for capacity enhancement in a specific section of an existing optical fiber by inserting a new link into it without deploying a new fiber.

Flow over a cluster of three equally spaced circular cylinders was studied by numerical simulation on base of the turbulent mode k-kl-ω for two incidence angles β=0° and 60°, at different Reynolds number,in this paper, flow interference pattern characteristics between cylinders, characteristics of force parameters and Strouhal number of each cylinder with different spacing ratios ranging from 1.5 to 4 at Re 8×104, 2×105and 2×106 had been obtained. At incidence angle β=0° and 60°, the wake was nearly symmetric if S/D≥2.0; at β=60°,S/D=1.5 and Re=2×105, the asymmetric periodic flow pattern occurred in the wake region which leaded to the significant effect on the surface mechanical parameters and Strouhal number which was found for the first time; the periodic flow regime of the wake region also occurred at S/D=1.35 and 1.5, without the same phenomenon at S/D=1.7 and 2.0; the phenomenon of periodic flow regime of the wake region was intrinsic and related to Reynolds number and space ratio. in addition, characteristics of force parameters of three cylinders mainly were affected by the interference between cylinders, at 1.5&lt;S/D&lt;4, which leaded to that the drag coefficient of three cylinders reduced with different Reynolds numbers. At incidence angle 60°, in subcritical and critical regime, the Strouhal numbers of the upstream cylinders were more than that of single cylinder, and with the enlargement of spacing ratio, the Strouhal number decreased; for the downstream cylinder , the Strouhal number is far less than that of single cylinder and with the enlargement of spacing ratio, the Strouhal number increases, which were another prominent flow inference influence. The results indicated the effect of flow interference between cylinders subjected to a cross flow over a cluster of three equally spaced cylinders on the flow pattern,surface mechanical parameters and Strouhal number.

Pulsating high frequency voltage injection can be used for sensorless control of SPMSM at zero and low speed ranges. However, the sensorless capability still faces challenges to the requirements of industrial application, especially at heavy load status. Aiming at this issue, this article proposes a sensorless capability expansion method for SPMSM based on inductance parameter identification. First, incremental inductances at d-q-axis and cross-coupling inductance are identified by three steps combining the rotating high frequency voltage injection and pulsating high frequency voltage injection, then, using polynomial curve fitting algorithm, apparent inductances are calculated. Second, positive DC current injection at d-axis is proposed to enhance the saliency ratio based on the analysis of parameter identification results. Compared with the conventional =0 or &lt; 0 method, when positive DC current is injected at d-axis, saliency ratio is enhanced. Third, convergence region is expanded at heavy load status and accuracy of rotor position estimation is improved using the proposed method. Finally, the experiment results validate that the sensorless capability of SPMSM is expanded.

(1) Background: Among the chronic complications of type 2 diabetes mellitus, cancer became the leading cause of death in several countries. Our objective was the determination of whether prevalent type 2 diabetes mellitus is associated with a higher incidence of cancer. (2) Methods: This study is a nationwide analysis performed in Hungary. Study population was divided into a group with type 2 diabetes mellitus and into a non-diabetic group. The primary outcome was the risk related to overall cancer incidence. A key secondary outcome was the overall incidence of cancer in distinct study years. Further outcomes were the annual percent changes. (3) Results: The odds ratio related to the overall incidence of cancer was 2.50 (95% confidence interval: 2.46-2.55, P&lt;0.0001) in patients with diabetes as related to controls. The odds ratio was higher in males than in females. The highest risk was found in the 18-39-year-old subgroup. The annual cancer incidence rate declined in controls, but not in patients with diabetes. Several types of cancer showed a decreasing tendency in non-diabetic controls.; (4) Conclusions: type 2 diabetes is associated with a higher risk of cancer. High risk in young patients with type 2 diabetes suggests that these young individuals should be considered as a risk group.

Gas turbine engines are widely used in various industries such as aviation, power generation, and marine propulsion due to their high efficiency and reliability. The combustion chamber of a gas turbine engine design contains a number of elements, including as the chamber's size and form, the fuel injection system, the ignition system, and the cooling system and it plays a critical role in the performance and efficiency of the engine. This research discusses the fabrication of a combustion chamber model for a gas turbine engine. The aim of this research is to develop a combustion chamber that is cost-effective, easily available, and can be fabricated in less time. The research covers the different types of combustion chambers used in gas turbine engines and compares their advantages and disadvantages. It then selects the best type of combustion chamber for the gas turbine engine based on its cost, availability, and fabrication time, Efficiency and high power to fuel ratio. The report also describes the fabrication process involved, including the techniques and materials used, along with safety precautions and environmental protection measures. Lastly, the research suggests future improvements and potential applications for the fabricated combustion chamber model.

In order to balance the conflicts among mass flow rate, total pressure ratio, adiabatic efficiency and stall margin in a low-bypass transonic fan, the optimization of the rotor blade is implemented in this study. An advanced 3D optimization design system is adopted, and flow diagnostic methods based on vorticity dynamics are employed to discuss the flow field. Results indicate that by controlling the blade camber line curvature, significant improvements in the aerodynamic performance for the fan stage are achieved, the total pressure ratio is increased by 1.90%, while the adiabatic efficiency and mass flow rate are increased by 4.45% and 5.82%, respectively. Vorticity diagnosis suggest that there exists a close link between performance parameters and vorticity parameters in the axial fan/compressor, both azimuthal vorticity and boundary vortex flux have significant influences on the stage performance. Moreover, the boundary layer separation is accompanied by the spike of entropy and static pressure, while the derivation/gradient of these flow parameters would also suffer drastic changes under the effect of shock wave. The vorticity parameters could provide detailed flow information about the on-wall flow with high accuracy, which provides the researchers with a novel method for the turbomachinery aerodynamic design and analysis.

This paper reports modelling outcomes for improvements to building energy performance in Indonesia. Long-term climate effects due to building energy demands including carbon emissions are also considered. The global change assessment model (GCAM) was used to generate the related end-user building energy data, including socioeconomics for urban areas of Indonesia. As a comprehensive study, the total life cycle of carbon in the building sector and the concept of zero-carbon buildings, including energy efficiency, zero-emissions electricity and fuel switching options were considered. Building shell conductance (u-value) of building envelope, floor area ratio (FAR), air conditioner (AC) efficiency, electrical appliances (APLs) efficiency, rooftop photovoltaic (PV) performance and ground source heat pump (GSHP) systems were considered as parameters to mitigate carbon emissions under the operational energy category in GCAM. Carbon mitigation associated with the cement production process was considered in the raw material category. Urban population and labour productivity in Indonesia were used as base inputs with projected growth rates to 2050 determined from available literature. Low growth rate ‘LowRate’ and high growth rate ‘HighRate’ were considered as variable inputs for u-value, FAR, AC efficiency, APLs efficiency, and PV capacity factor to model emissions mitigation. The energy consumption of the GSHP was compared to the conventional reverse cycle ACs to identify the potential of the GSHP as a fuel-switching option. Only base input data were used for cement production process parameters without applying any variable inputs. GCAM base scenarios based on input data only (without modifying variable data) for the residential building sector in Indonesia were considered the benchmark for this study. Total potential carbon emissions mitigation was found to be 432 Mt CO2-e for the residential building sector in Indonesia over 2020-2050. It was found that an average of 24% carbon emissions mitigation could be achieved by 2020-30 and 76% in 2031-2050.

In this paper, we first establish upper stochastic bounds on the lifetime of a used cold standby system with arbitrary age, using the likelihood ratio order and the usual stochastic order. Then, stochastic comparisons are made between the lifetime of a used cold standby system with age t and the lifetime of a cold standby system consisting of used components with age t using the likelihood ratio order and the usual stochastic order. We use illustrative examples to explore the results presented.

Type 2 diabetes mellitus may be complicated with chronic complications including diabetic neuropathy (DN). Timely diagnosis is crucial in treatment and maybe reversal of this complication. C reactive protein to albumin ratio (CAR) is considered as a marker of inflammation in various diseases that characterized with acute or chronic inflammation. Since diabetic neuropathy and type 2 diabetes mellitus are also associated with chronic, low grade inflammation, we aimed to study CAR levels of type 2 diabetic subjects with diabetic neuropathy and to compare to those in patients without diabetic neuropathy. Type 2 diabetic patients presented to our institutional outpatient clinics were divided into two according to the presence of DN. Subjects with DN were listed as DN group and others were as non-DN group. Characteristics and laboratory data, including CAR, in DN and non-DN groups were compared. Median CAR of the DN and non-DN groups were 2,19 (0,2-49)% and 0,56 (0,02-5,8)%, respectively (p&lt;0.001). CAR was significantly and positively correlated with age (r=0.15, p&lt;0.001), weight (r=0.19, p=0.01), BMI (r=0.11, p=0.03), waist circumference (r=0.10, p=0.046), fasting plasma glucose (r=0.14, p=0.004), serum creatinine (r=0.25, p&lt;0.001), triglyceride (r=0.17, p&lt;0.001), and LDL-cholesterol (r=0.13, p=0.001) levels. Moreover, CAR was inversely correlated with eGFR levels (r=-0.16, p&lt;0.001). The sensitivity and specificity of CAR (when higher than 1,02%) in predicting diabetic neuropathy were 78% and 73%, respectively (AUC: 0.84, p&lt;0.001, 95% CI: 0,82-0,87). Moreover, high CAR level was an independent risk factor of diabetic neuropathy (p&lt;0.001, OR: 1.34, 95% CI: 0.48-1.62). In conclusion, elevated CAR levels could be considered as a marker of diabetic neuropathy.

Bacterial transformation is the essential tool for introducing foreign DNA into bacterial cells in a host of recombinant technology applications useful for biomanufacturing and drug production. Thus far, chemically competent cells remain an important enabling technology for bacterial transformation given its facile transformation approach. However, many parameters affect transformation efficiency, and there is relatively little documentation of their cross-interacting effect in the literature. This work explores the roles played by incubation time on ice, competent cell concentration, and plasmid-to-cell ratio on transformation efficiency in Escherichia coli DH5α. Results revealed that increases in incubation time improve transformation efficiency, but 2 minutes incubation still yield appreciable efficiency. On the other hand, low concentration competent cells (10⁶ CFU/mL) yielded significant improvement in transformation efficiency compared to high concentration competent cells (10⁸ CFU/mL). In terms of plasmid-to-cell ratio, higher ratio increases transformation efficiency. Overall, bacterial transformation is incompletely understood particularly in the area of cross-interacting parameters. Experiments reported here revealed the possibility of short duration transformation where lower competent cell concentration and higher plasmid-to-cell ratio could improve transformation.

Drought stress is a major production constraint in crops globally. Crop wild relatives are important source of resistance and tolerance for both biotic and abiotic stresses, respectively. A breeding program was initiated to introgress drought tolerance in sunflower through hybridization between the wild species Helianthus argophyllus and the cultigen pool of H. annuus. Selection was carried out in the F2 to F5 segregating populations for high cuticular waxes, smaller leaf area, single heading and high oil content. The selected F5 breeding lines were compared with non-adapted elite sunflower germplasm in a replicated randomized complete block research project using different water treatments comparing fully irrigated (T0), with 75 (T1), 50 (T2) and 25% (T3) irrigation treatments. The comparison between the two types of germplasm showed that drought tolerant breeding lines had comparatively lesser decreases in leaf area, shoot weight and root shoot ratio 10 under the various drought treatments. Leaf area of the drought selected F5 lines were smaller than that of the elite germplasm under controlled irrigated treatments, but they maintained their leaf area under the drought treatments. Several drought resistant promising lines D-2, D-5, and D-27 were identified and showed high leaf area, great root length and increase root to shoot ratio under the highest stressed treatments (T3). Some of the lines could be directly used for the development of drought tolerant hybrids. Combining ability test indicated D-27 (F7) as good general combiner for seed yield plant−1 and oil contents when mated with male line RSIN.82. These hybrids could help to minimize seed yield losses due to water stress and to achieve profitable cultivation of sunflower in 18 arid regions of Pakistan.

Voronoi mosaics inspired by the seed points placed on the Archimedes Spirals are reported. Voronoi entropy was calculated for these patterns. Equidistant and non-equidistant patterns are treated. Voronoi mosaics built from a sells of equal size which are of a primary importance for decorative arts are reported. The pronounced prevalence of hexagons is inherent for the patterns with an equidistant and non-equidistant distribution of points, when the distance between the seed points is of the same order of magnitude as the distance between the turns of the spiral. Penta- and heptagonal “defected” cells appeared in the Voronoi diagrams due to the finite nature of the pattern. The ordered Voronoi tessellations demonstrating the Voronoi entropy larger than 1.71, reported for the random 2D distribution of points, were revealed. The dependence of the Voronoi entropy on the total number of the seed points located on the Archimedes Spirals is reported. Voronoi tessellations generated by the phyllotaxis-inspired patterns are addressed. The aesthetic attraction of the Voronoi mosaics arising from seed points placed on the Archimedes Spirals is discussed.

Student mobility is one of the most important indicators to reflect institutional internationalization in a sustainable higher education system. While student mobility issues have been addressed persistently, the phenomenon is rarely discussed in association with higher education expansion. Since higher education sustainable development has received much scholarly attention, monitoring student mobility flows to adjust international strategies is necessary. This study explored practical approaches to detect student mobility flows in the process of higher education expansion. Targeting Taiwan’s higher education system as an example, we addressed the topic of system expansion and the core issues of student mobility. Target series data were collected from 1950 to 2021, including higher education enrollment, gross enrollment ratio (GER), and number of inbound and outbound students. The data were transformed with index formats, for example enrollment increasing ratio (IR) and net flow ratio. The cross-correlation function (CCF) and autoregressive integrated moving average (ARIMA) were used to determine the correlations of the series data and their future trends. The findings suggested that the effect of system expansion, with GER and IR, might influence the mobility ratios significantly in the process of higher education expansion. This study confirmed that the time series approaches work well in detecting the phenomena of higher education expansion and their effects on student mobility flows in the future.

The C/N ratio is an extremely important parameter in the composting process, which is directly responsible for the growth of microorganisms. A low C/N ratio contributes to higher emissions of greenhouse gases and odorous substances, such as ammonia (NH3), which is formed by nitrogen mineralization. Due to the highly toxic effects of ammonia, it is a particularly unwanted by-product that can disrupt the composting process because it poisons microorganisms and cause environmental issues. The activity of anammox bacteria, so far analyzed only in wastewater treatment processes, is a particularly efficient method of nitrogen removal, having an advantage over the conventional methods used previously. Our study proofs the presence of anammox bacteria during composting, what gives an opportunity to improve the process and reduce its impact on atmospheric pollution. Despite the aerobic nature of this process, the composted mass of waste presents conditions conducive to the development of these ammonia oxidizing bacteria, as well as other strains of microorganisms cooperating with them. This makes it possible to compost at a low C/N ratio; in addition, there is no need for additional energy supply through aeration, as the processes carried out by anammox bacteria do not require oxygen.

Unmanned Aerial Vehicles (UAVs) in particular multirotors are becoming the {\it de facto} tool for aerial sensing and remote inspection. In large industrial facilities, a UAV can transmit an online video stream to inspect difficult to access structures, such chimneys, deposits and towers. However, the communication range is limited, constraining the UAV operation range. This limitation can be overcome with relaying UAVs placed between the source UAV and the control station, creating a line of communication links. In this work we assume the use of a digital data packet network technology, namely WiFi, and tackle the problem of defining the exact placement for the relaying UAVs that creates an end-to-end channel with maximal delivery of data packets. We consider asymmetric communication links and we show an increase as large as $15$\% in end-to-end packet delivery ratio when compared to an equidistant placement. We also discuss the deployment of such a network and propose a fully distributed method that converges to the global optimal relay positions taking, on average, 1.4 the time taken by a centralized method.

In this experimental work, pure nickel oxide and Al-doped NiO thin films have successfully been elaborated onto glass substrates by solar spray pyrolysis technique. The substrates were heated at around 450°C using a solar heater (furnace). The structural, optical and electrical properties of the elaborated Al-doped films have been studied at different atomic percentage ratios (0, 0.5, 1, 1.5 and 2 at. %). The results of Al-doped NiO films XRD patterns were, the formation of (NiO) phase under a cubic crystalline structure (polycrystalline) with a strong favored orientation along (111) plane were noticed at all sprayed films. When Al doping ratio reaches 1 at.%, an growth in crystallite size over 31.9 nm was obtained denoting the nano-structure of the product, which confirmed by SEM images. In addition, aluminum oxide Al₂O₃ was clearly observed at 1.5 at.% Al ratio. Otherwise, all thin films have a good optical transmission in the visible region of about 65%, the optical band gap energy decreased from 3.69 to 3.64 eV with increasing Al doping ratio. It is shown that the layer deposited with 0.5 at.% has less disorder with few defects. The investigation on electrical properties of elaborated thin films confirmed that the conductivity of NiO films was improved, after doping them with Al which affirms their p-type character of semiconductor. However, an addition of an excessive quantity of Al content causes the formation of Al₂O₃ which leads to a decrease in the conductivity. It is worth mentioning that the Al content of 0.5 at.% is the optimum ratio in terms of electrical conductivity and formation defect. Al-doped NiO can be used in various optoelectronic devices due to its good transparency and high electrical conductivity.

Yogic and meditative traditions have long held that the fluctuations of the breath and the mind are intimately related. While respiratory modulation of cortical activity and attentional switching are established, the extent to which electrophysiological markers of attention exhibit synchronization with respiration is unknown. To this end, we examined 1) frontal midline theta-beta ratio, an indicator of attentional control state known to correlate with mind wandering episodes and functional connectivity of the executive control network; 2) pupil diameter (PD), a known proxy measure of locus coeruleus (LC) noradrenergic activity; and 3) respiration for evidence of phase synchronization and information transfer (multivariate Granger causality) during quiet restful breathing. Our results indicate that both TBR and PD are simultaneously synchronized with the breath, suggesting an underlying oscillation of an attentionally relevant electrophysiological index that is phase-locked to the respiratory cycle which could have the potential to bias the attentional system into switching states. We highlight the LC’s pivotal role as a coupling mechanism between respiration and TBR, and elaborate on its dual functions as both a chemosensitive respiratory nucleus and a pacemaker of the attentional system. We further suggest that an appreciation of the dynamics of this weakly coupled oscillatory system could help deepen our understanding of the traditional claim of a relationship between breathing and attention.

Most existing flexible count regression models allow only approximate inference. Balanced discretization is a simple method to produce a mean-parametrizable flexible count distribution starting from a continuous probability distribution. This makes easy the definition of flexible count regression models allowing exact inference under various types of dispersion (equi-, under- and overdispersion). This study describes maximum likelihood (ML) estimation and inference in count regression based on balanced discrete gamma (BDG) distribution and introduces a likelihood ratio based latent equidispersion (LE) test to identify the parsimonious dispersion model for a particular dataset. A series of Monte Carlo experiments were carried out to assess the performance of ML estimates and the LE test in the BDG regression model, as compared to the popular Conway-Maxwell-Poisson model (CMP). The results show that the two evaluated models recover population effects even under misspecification of dispersion related covariates, with coverage rates of asymptotic 95% confidence interval approaching the nominal level as the sample size increases. The BDG regression approach, nevertheless, outperforms CMP regression in very small samples (n = 15 − 30), mostly in overdispersed data. The LE test proves appropriate to detect latent equidispersion, with rejection rates converging to the nominal level as the sample size increases. Two applications on real data are given to illustrate the use of the proposed approach to count regression analysis.

Natural capital is the wealth of nations that give them the economic status they represent. Worldwide, vulnerable people depend on natural capital for employment, salaries, wealth, and livelihoods and, in turn, determine the developmental index of the nation to which they belong. The availability of ecological services is crucial for clean water and air, food and fodder, and agricultural development. In this short commentary, we have tried to sum up the ideas and discussions over natural capital's role in ascribing economic status to countries. We have discussed how the prosperity of humans is intertwined with the services ecosystems provide and how poor natural resource management (NRM) has adversely cost human well-being. The paper concludes that to ensure the current and future human well-being, an in-depth understanding of the services ecosystems provide, is essential.

Abstract: This paper is focusing on the stabilisation of soil using jute fibre as soil stabilizer. Stabilisation is the process of modifying the properties of a soil to improve its engineering performance and used it for a variety of engineering works. This study examines the potential of soil stabilization with jute fibre when it is cut into roughly 30mm lengths as stabilizer. The varying percentages like 0.5%, 1%, 1.5 and 2% of pieces of jute fibre were used and mixed it with soil. The laboratory tests such as California Bearing Ratio (CBR) test, modified compaction tests and direct shear strength tests have been conducted to observe the change in engineering properties of soil. On the basis of the experiments performed, it can be concluded that the stabilization of soil using 30mm pieces of jute as stabilizer improves the strength characteristics of the soil so that it becomes usable as one of the reinforcing material for the construction of roadways, parking areas, site development projects, airports and many other situations where sub-soils are not suitable for construction.

In the present scenario of increased industrialization and transportation in the world leads to increased consumption of fossil fuels which in turns leads to depletion of fossil fuels at a faster rate. Fossil fuels combustion is the dominant source for greenhouse gases and global warming. In view of energy crisis raised in 1970’s and environmental concern, many researches are directed towards search of alternative fuels which can replace consumption of fossil fuels as well as reduce pollution. In developing countries like India which is agriculture land the best alternative fuels are biodiesel and ethanol as they are produced from renewable feedstocks like sugarcane, corn etc. and they are also less hazardous to environment because of lower emission property. Ethanol blends results in significant reduction of emissions of hydrocarbon (HC), carbon monoxide (CO) and particulates matter but increase in nitrogen oxides (NOx). The main purpose of ethanol addition is to reduce the viscosity of biodiesel blends. This paper represents significance of Compression Ratio(CR) on performance, combustion and emission of single cylinder four stroke CI diesel engine by using various compression ratios such as 17.5:1, 18.5:1 and 19.5:1. Experimental research has been conducted with four types of ethanol blends, namely E10, E20, E30 and E40. Ethanol-biodiesel mixture mixed with 2% emulsifier 1% diethyl carbonate and 1% ethyl acetate to maintain similarity and to avoid phase separation. Ethanol subjected to high compression ratio has been used to increase brake thermal efficiency (BTE). The compression ratio has been increased to improve the combustion and performance of the diesel engine.

The purpose of this paper is to explore which financial performance indicators (FPIs) evaluate the level of supply chain capability (SCC) that explicitly touches all of the business functions and processes within and beyond the company. The authors investigated nine FPIs that were selected from the financial statements of 155 companies within nine industries. The authors find that suitable FPIs to measure SCC for shareholders’ value are return-on-assets (ROA), days-sales-outstanding (DSO), and current ratio (CR). This means that higher ROA, shortened DSO, and an appropriate level of CR could reach a sustainable supply chain. These results will help the industry to avert a major disruption in supply chain processes and activities using suitable financial performance indicators.

Diffusion bonding is often used on pre-machined parts to generate internal cavities, e.g. for cooling injection molding tools close to the mold cavity. Only then, the workpieces are finished to their final dimensions. In the case of micro-process devices, however, it is essential to precisely control the deformation, as otherwise uncontrollable pressure losses will occur with channel cross-sections in the sub-millimeter range. Post-processing is not possible. The most important process parameters for diffusion bonding are temperature, dwell time and contact pressure, with the bonding temperature and contact pressure acting in opposite directions and showing a strong non-linear dependence on deformation. In addition, the deformation is influenced by a number of other factors such as the absolute size of the cross-section and the aspect ratio of the parts, the dimensions and distribution of the internal cross sections and the overall percentage of the cross-section to be bonded. In micro process engineering, small material cross-sections in the range of the materials microstructure can facilitate additional deformation mechanisms such as grain boundary sliding, which are not relevant at all for larger structures. For parts consisting of multiple layers, tolerances in thickness and roughness of multiple surfaces must be levelled, contributing to the percentaged deformation. This makes it difficult, especially in micro process engineering and in single or small series production, to determine suitable joining parameters in advance, which on the one hand do not cause unforeseen large deformations, but on the other hand reliably produce highly vacuum-tight components. Hence, a definition of a fixed percentaged deformation does not work for all kinds of components. This makes it difficult to specify parameters for surely obtain high-vacuum tight parts. For successful diffusion bonding, atoms must diffuse over the bonding planes, forming a monolithic part in which the original layers are no longer visible. Only then, mechanical properties identical to those of the base material, which has been subjected to identical heat treatment, can be achieved. In this paper, the impacts of different material cross section widths as well as of the aspect ratio on deformation were investigated. By accident, it was found that also accuracy of the temperature measurement may have a serious impact in terms of deformation.

The highest efficiency solar cell won in the efficiency race does not always give the most excellent annual energy yield in the real world solar condition that the spectrum is ever-changing. The study of the radiative coupling of the concentrator solar cells implied that the efficiency could increase by the recycle of the radiative recombination generated by the surplus current in upper junction. Such configuration is called by a super-multi-junction cell. We expanded the model in the concentrator solar cell to non-concentrating installation. It was shown that this super-multi-junction cell configuration was found robust and can keep the maximum potential efficiency (50 % in realistic spectrum fluctuation) up to 10 junctions. The super-multi-junction cell is also robust in the bandgap engineering of each junction. Therefore, the future multi-junction may not be needed to tune the bandgap for matching the standard solar spectrum, as well as relying upon artificial technologies like ELO (Epitaxial lift-off), wafer-bonding, mechanical-stacking, and reverse-growth, but merely uses up-right and lattice-matching growth technologies. We have two challenging techniques; one is the optical cap layer that may be the directional photon coupling layer in the application of the photonics technologies, and another is the high-quality epitaxial growth with almost 100 % of the radiative efficiency.

The bulk backscattering ratio ($\tilde{b_{bp}}$) is commonly used as a descriptor of the bulk real refractive index of the particulate assemblage in natural waters. Based on numerical simulations, we analyze the impact of heterogeneity of phytoplankton cells on $\tilde{b_{bp}}$. $\tilde{b_{bp}}$ is modeled considering viruses, heterotrophic bacteria, phytoplankton, detritus, and minerals. Three study cases are defined according to the relative abundance of these different components. Two study cases represent typical situations in open ocean, outside (No-B/No-M) and inside bloom (B/No-M). The third study case is typical of coastal waters with the presence of minerals. Phytoplankton cells are modeled by a two-layered spherical geometry representing a chloroplast surrounding the cytoplasm. The $\tilde{b_{bp}}$ values are higher when heterogeneity is considered because the contribution of coated spheres to backscattering is higher than homogeneous spheres. The impact of heterogeneity is however strongly conditioned by the hyperbolic slope $\xi$ of the particle size distribution. Even if the relative concentration of phytoplankton is small (<1%), $\tilde{b_{bp}}$ increases by about 60% (for $\xi=4.3$ and for the No-B/No-M water body), when the heterogeneity is taken into account, in comparison with a particulate population only composed by homogeneous spheres. As expected, heterogeneity has a much smaller impact (about 5$\%$ for $\xi=4.3$) on $\tilde{b_{bp}}$ when minerals are added.

In the present study, the performance of a 70 L photobioreactor, operating outdoors, was investigated using a purple bacterial strain as Rhodopseudomonas sp. S16-VOGS3 for producing poly-3-hydroxybutyrate (PHB). The novel photobioreactor was equipped with 5L-shaped rows; the bottom of every row was placed in a stainless-steel tank containing water with controlled temperature. The photofermentation trials were carried out under fed-batch mode and under a semi-continuous regimen using lactic acid as carbon source. The effect of the irradiance and the C/N ratio on the PHB accumulation was investigated, in order to evaluate the optimal bacterial growth. The results showed the feasibility of the prototype photobioreactor for the production of PHB by Rhodopseudomonas sp. S16-VOGS3 under the natural light/dark cycle. During the fed-batch growth (144 h long), the cumulative PHB increased quickly reaching the maximum value of 377 mg/L and decreased to 255 mg/L during the semi-continuous regimen (336 h long).

Glaucoma is a disease associated with retina of eye. Presently, millions of human being is suffering from this disease. Early detection of these diseases can save the people from blindness. Therefore, various methods have been developed for its detection. In this paper, we have studied the reported methods and summarized their performance in terms of accuracy of detection.

Some studies have demonstrated that in vivo degradation processes are influenced by the material’s physico-chemical properties. The present study compares two hydroxyapatites manufactured on an industrial scale, deproteinized at low and high temperatures, and how physico-chemical properties can influence the mineral degradation process of material performance in bone biopsies retrieved 6 months after maxillary sinus augmentation. Residual biomaterial particles were examined by field scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX) to determine the composition and degree of degradation of the bone graft substitute material. According to the EDX analysis, the Ca/P ratio significantly lowered in the residual biomaterial (1.08±0.32) compared to the initial composition (2.22±0.08) for the low-temperature sintered group, which also presented high porosity, low crystallinity, low density, a large surface area, and poor stability and a high resorption rate compared to the high-temperature sintered material. This demonstrates that variations in the physico-chemical properties of bone substitute material clearly influence the degradation process. Further studies are needed to determine whether the resorption of deproteinized bone particles proceeds slowly enough to allow sufficient time for bone maturation to occur.

Finding a good MIMO system model also major issue in Wireless Communication system. It is facing with so many problem, one of the major problem is finding good system model in terms of capacity and transmitting antenna system. In this paper, we analyze the channel capacity of various MIMO system model with some constant SNR level and outage probability. We establish a novel idea for MIMO system models as consider as 2^N- MIMO system model and find-out change in channel capacity when different transmitting antennas with constant SNR and outage probability. The channel capacity ratio CC_R is presented here on the basis of 2^N- MIMO channel capacity model. Number of transmitted antenna presented in MIMO system is increases is well-known however paper shows change in capacity in simple form.

Salinity, resulting from climate change and excessive mineral fertilization, burdens farmers and negatively impacts soil and water ecosystems in the Northeastern Nile Delta. Organic and biological approaches are crucial for addressing these issues. This study examined the effects of individual and combined inoculations with cyanobacteria, yeast, and Arbuscular Mycorrhizal Fungi (AMF), with or without K-humate, on enhancing salinity tolerance, increasing yield, and improving crop quality of wheat and faba bean. The aim was to reduce NPK mineral fertilizer application rates to 25% of recommended doses. An economic evaluation was also conducted. In a preliminary laboratory experiment, the interactive effects of these microbiomes on the production of plant antioxidant enzymes and soil enzymes were investigated under salinity stress. Results showed that co-inoculation, especially with K-humate, yielded superior outcomes compared to individual inoculations. The laboratory experiment findings were confirmed by a field trial conducted in saline-alkaline soil in the Northeastern Nile Delta region. The study found that the integrated inoculation of cyanobacteria, yeast, and mycorrhizae with K-humate, along with 25% mineral NPK fertilization enhanced microbial activity, including AMF colonization, spore density, and total bacteria, cyanobacteria, and yeast counts in the plant rhizosphere. It also increased soil enzyme activity, improving soil fertility compared to individual or mineral control treatments. This integration resulted in wheat yields of 2.77 tons/ha and faba bean yields of 4.75 tons/ha. Crop quality improved, with higher levels of nitrogen, potassium, phosphorus, and protein in wheat grains and faba bean seeds. Microbiomes inoculation increased potassium uptake over sodium, enhancing the potassium/sodium ratio and salt stress tolerance. This approach reduces reliance on costly mineral fertilizers by up to 75%, enabling economically viable cultivation in marginal lands. These sustainable practices optimize resource utilization, maximize economic efficiency, and preserve natural resources.

Dengue, a perilous fever-type illness transmitted by mosquitoes, remains a significant global health concern. The incidence of dengue outbreaks is primarily influenced by climate factors, contributing to fluctuating dengue cases. Therefore, this study aims to develop predictive models for dengue outbreaks employing Machine Learning (ML) techniques. Four distinct ML models, namely K-Nearest Neighbor (KNN), Random Forest (RF), Gradient Boosting Regressor (GBR), and Support Vector Regressor (SVR), were employed in this study. Prior to model analysis, thorough data preprocessing was conducted. In some instances, certain attributes exhibiting sparse correlations with dengue occurrence were eliminated based on correlation analysis. Upon finalizing the models, performance evaluation was executed through comparison based on Mean Absolute Error (MAE) metrics. The findings of this comparative analysis revealed that the KNN model exhibited significantly superior performance compared to the other three models. This outcome underscores the potential of KNN in enhancing the accuracy of dengue outbreak predictions.

In this article, we describe a simple procedure for evaluating the sterility of nutrient media using a shear-horizontal surface acoustic wave (SH-SAW) biosensor. We used the SH-SAW biosensor platform to monitor the time-dependent phase responses of the material for the media that binds to a monolayer of 3-mercaptopropanyl-N-hydroxy succinimide on the biosensor surface. Increases in the phase shift less than 50% of the starting phase shift recorded 180 minutes after the sterilization indicate a successful sterility test of the media. Our devices were then applied to sterility testing using a viable Escherichia coli (E. coli) K-12 solution to confirm our hypothesis. Filtered LB Broth was the negative control, and a 24-hour culture of E. coli was the positive control. Before testing, the cell solution was pelleted, the media decanted, and then replaced with a 1x phosphate-buffered saline solution (1x PBS). Since we know that the N-hydroxysuccinimide residues will bind to amine groups, only in cases where microbial species are present will the surface binding increase greater than 50%. We confirmed our hypothesis using SH-SAW biosensors and overnight E. coli cultures. The sensitivity for our 250 MHz quartz SH-SAW sensors was calculated based on the response from the E. coli K-12 solution over the linear dynamic range, which appears to be 2x10^4 – 2x10^7 CFU per ml and has a sensitivity of S = 1.655x10^5 o m2 Kg-1. The limit of detection (LOD) for these sensors was calculated to be approximately 2x10^-9 grams (g), which is estimated to be approximately 2,000 Escherichia coli (E. coli) K-12 cells. However, the sensitivity and insertion loss remained approximately unchanged before and after coating the sensor with 3,3'-Dithiobis(succinimidyl) Propionate (DSP).

A class of nearly Sasakian manifolds is considered. We discussion geometric effects of some symmetries on such manifolds, and show, under a certain condition, that the class of Ricci-symmetric nearly Sasakian manifolds is a subclass of Einstein manifolds. We prove that a nearly Sasakian space form with Ricci tensor satisfying the Codazzi equation is either a Sasakian manifold with a constant $\phi$-holomorphic sectional curvature $\mathcal{H}=1$ or a $5$-dimensional proper nearly Sasakian manifold with a constant $\phi$-holomorphic sectional curvature $\mathcal{H}>1$. We also prove that the spectrum of the operator $H^{2}$ generated by the nearly Sasakian manifold is a set of simple eigenvalue $0$ and an eigenvalue of multiplicity $4$. We show that there exist integrable distributions on the same manifolds with totally geodesic leaves, and prove that there are no proper nearly Sasakian space forms with constant sectional curvature.

Anomaly Detection in real time data is accepted as a vital research area. Clustering has effectively been tried for this purpose. As the datasets are real time, the time of generating of the data is also important. In this article, we introduce a mixture of partitioning and agglomerative hierarchical approach to detect anomalies from such datasets. It is a two-phase method which follows partitioning approach first and then agglomerative hierarchical approach. The dataset can have mixed attributes. In phase-1, a unified metric defined on mixed attributes is used. The same is also used for merging of similar clusters in phase-2. Also, we have kept the track of time attribute of each data instance which produces the clusters with their lifetimes in phase-1. Then in phase-2, we merge the similar clusters. While merging, the similar clusters, the lifetimes of the corresponding clusters with overlapping cores are to be superimposed producing fuzzy time intervals. This way, each cluster will have an associated fuzzy lifetime. The data instances either belonging sparse clusters or not belonging to any of the clusters can be treated as anomalies. The efficacy of the algorithms can be established using both complexity analysis as well as experimental studies.

BackgroundIt is unclear what underpins the large global variations in the prevalence of fluoroquinolone resistance in gram-negative bacteria. We tested the hypothesis that different intensities in the use of quinolones for food-animals plays a role. MethodsWe used Spearman’s correlation to assess if the country-level prevalence of fluoroquinolone resistance in human infections with Acinetobacter baumannii, Escherichia coli, Klebsiella pneumoniae and Pseudomonas aeruginosa was correlated with the use of quinolones for food producing animals. Linear regression was used to assess the relative contributions of country-level quinolone consumption for food-animals and humans on fluoroquinolone resistance in these 4 species. ResultsThe prevalence of fluoroquinolone resistance in each species was positively associated with quinolone use for food-producing animals (E. coli [ρ=0.55; P<0.001], K. pneumoniae [ρ=0.58; P<0.001]; A. baumanii [ρ=0.54; P=0.004]; P. aeruginosa [ρ=0.48; P=0.008]). Linear regression revealed that both quinolone consumption in humans and food animals were independently associated with fluoroquinolone resistance in E. coli and A. baumanii. ConclusionsReducing quinolone use in food-producing animals may help retard the spread of fluoroquinolone resistance in various gram negative bacterial species.

The Lamiaceae belong to the species-richest families of flowering plants and harbor many species used as herbs or for medicinal applications, such as Basils or Mints. Evolution of this group has been driven by chemical speciation, mainly of Volatile Organic Compounds (VOCs). The commercial use of these plants is characterized by a large extent of adulteration and surrogation. To authenticate and discern the species, is, thus, relevant for consumer safety, but usually requires cumbersome analytics, such as Gas Chromatography, often to be coupled with Mass Spectroscopy. We demon-strate here that quartz-crystal microbalance (QCM)-based electronic noses provide a very cost-efficient alternative, allowing for a fast, automated discrimination of scents emitted from leaves of different plants. To explore the range of this strategy, we used leaf material from four genera of Lamiaceae along with Lemongrass as similarly scented, but non-related outgroup. In order to unambiguously differentiate the scents from the different plants, the output of the 6 different SURMOF/QCM sensors was analyzed using machine learning (ML) methods, together with a thorough statistical analysis. The exposure and purging datasets (4 cycles) obtained from a QCM-based, low-cost homemade portable e-Nose were analyzed with Linear Discriminant Analysis (LDA) classification model. Prediction accuracies with repeating test measurements reached values of up to 90%. We show that it is not only possible to discern and identify plants on the genus level, but even to discriminate closely related sister clades within a genus (Basil), demonstrating that e-Noses are a powerful technology to safeguard consumer safety against the challenges of globalized trade.

Quadruplex-interactive small molecules have a wide potential application, not only as drugs but also as sensors of quadruplexes structures. The purpose of this work is the synthesis of analogues of the bis-methylquinolinium-pyridine-2,6-dicarboxamide G4 ligand 360A, to identify relevant structure-activity relationships to apply to the design of other G4-interactive small molecules bearing bis-quinoline or bis-isoquinoline moieties. Thermal denaturation experiments revealed that non-methylated derivatives with a relative 1,4 position between the amide linker and the nitrogen of the quinoline ring are moderate G4 stabilizers, with a preference for the hybrid h-Telo G4. Insertion of a positive charge upon methylation of quinoline/isoquinoline nitrogen increases compounds capacity to selectively stabilize G4s compared to duplex DNA, with a preference for parallel structures. Among these, compounds having a relative 1,3-position between the charged methylquinolinium/isoquinolinium nitrogen and the amide linker are the best G4 stabilizers. More interestingly, these ligands showed different capacities to selectively block DNA polymer-ization in a PCR-stop assay and to induce G4 conformation switches of hybrid h-Telo G4. Mo-lecular dynamic simulations with the parallel k-RAS G4 structure showed that the relative spatial orientation of the two methylated quinoline/isoquinoline rings determines the ligands mode and strength of binding to G4s.

In this paper, we consider the relation of more than four harmonic points in a line. For this purpose, starting from the dependence of the harmonic points, Desargues’ theorems, and perspectivity, we note that it is necessary to conduct a generalization of the Desargues’ theorems for projective complete n-points, which are used to implement the definition of the generalization of harmonic points. We present new findings regarding the uniquely determined and constructed sets of H-points and their structure. The well-known fourth harmonic points represent the special case (n=4) of the sets of H-points of rank 2, which is indicated by P42.

Feature selection is a crucial step to overcome the curse of dimensionality problem in data mining. This work proposes Recursive k-means Silhouette Elimination (RkSE) as a new unsupervised feature selection algorithm to reduce dimensionality in univariate and multivariate time-series datasets. Where k-means clustering is applied recursively to select the cluster representative features, following a unique application of silhouette measure for each cluster and a user-defined threshold as the feature selection or elimination criteria. The proposed method is evaluated on a hydraulic test rig, multi sensor readings in two different fashions: (1) Reduce the dimensionality in a multivariate classification problem using various classifiers of different functionalities. (2) Classification of univariate data in a sliding window scenario, where RkSE is used as a window compression method, to reduce the window dimensionality by selecting the best time points in a sliding window. Moreover, the results are validated using 10-fold cross validation technique. As well as, compared to the results when the classification is pulled directly with no feature selection applied. Additionally, a new taxonomy for k-means based feature selection methods is proposed. The experimental results and observations in the two comprehensive experiments demonstrated in this work reveal the capabilities and accuracy of the proposed method.

In the current natural environment, due to the complexity of the background and the high similarity of the color between immature green tomato and plant, the occlusion of the key organs (flower and fruit) by the leaves and stems will lead to low recognition rate and poor generalization of the detection model. Therefore, an improved tomato organ detection method based on convolutional neural network has been proposed in this paper. Based on the original Faster R-CNN algorithm, Resnet-50 with residual blocks was used to replace the traditional vgg16 feature extraction network, and K-means clustering method was used to adjust more appropriate anchor size than manual setting to improve detection accuracy. A variety of data augmentation techniques were used to train the network. The test results showed that compared with the traditional Faster R-CNN model, the mean average precision (mAP) of the optimal model was improved from 85.2% to 90.7%, the memory requirement decreased from 546.9MB to 115.9 MB, and the average detection time was shortened to 0.073S/sheet. As the performance greatly improved, the training model can be transplanted to the embedded system, which lays a theoretical foundation for the development of precise targeting pesticide application system and automatic picking device.

Many clinical research datasets have a large percentage of missing values that directly impacts their usefulness in yielding high accuracy classifiers when used for training in supervised machine learning. While missing value imputation methods have been shown to work well with smaller percentages of missing values, their ability to impute sparse clinical research data can be problem specific. We previously attempted to learn quantitative guidelines for ordering cardiac magnetic resonance imaging during the evaluation for pediatric cardiomyopathy, but missing data significantly reduced our usable sample size. In this work, we sought to determine if increasing the usable sample size through imputation would allow us to learn better guidelines. We first review several machine learning methods for estimating missing data. Then, we apply four popular methods (mean imputation, decision tree, k-nearest neighbors, and self-organizing maps) to a clinical research dataset of pediatric patients undergoing evaluation for cardiomyopathy. Using Bayesian Rule Learning (BRL) to learn ruleset models, we compared the performance of imputation-augmented models versus unaugmented models. We found that all four imputation-augmented models performed similarly to unaugmented models. While imputation did not improve performance, it did provide evidence for the robustness of our learned models.

This research investigates fiber-reinforced cementitious composites, with a particular emphasis on the geometric properties of soft micro and macro fibers. These fibers are characterized by a lower elastic modulus and larger aspect ratios than steel fibers. The composites were manufactured using a cement-to-sand ratio of 1:2.5, with 20% fly ash serving as a partial substitute. In order to attain varying strengths, two water-to-binder ratios (0.55 and 0.60) were implemented. Synthetic fibers, such as carbon and polypropylene, and natural sisal fibers, were introduced in volumes varying from 0.4% to 2.27%, with aspect ratios ranging from 71 to 3750. The flexural strength and behavior were evaluated using 75x75x380 mm prisms, while the compressive strength was measured using 50 mm cubes. Load-deflection curves were developed to investigate fracture behavior. The behavior of specimens reinforced with fibers post-cracking is dependent upon the matrix compressive strength, fiber type, quantity, and aspect ratio. A regression analysis was conducted on data from this study and previous publications to develop an equation that predicts the ratio of modulus of rupture (MOR) to initial fracture strength. The variables are matrix strength and fiber characteristics. The results reveal that carbon fiber-reinforced composites (CFRCCs) exhibit considerable brittleness post-cracking, despite exhibiting a flexural strength that is two to three times greater than that of control specimens. When workability is not compromised, the maximal load capacity and deflection are improved by increasing the fiber volume and aspect ratio. The maximal load stress is more significantly influenced by volumes of fibers than by aspect ratio.

The characteristics of tight sandstone, such as small pores, complex pore structures, low permeability, and low porosity, make it difficult to accurately characterize its pore structure. This represents a major challenge in the exploration and development of tight sandstone oil and gas reservoirs. This article conducts a simulation study on the impact of characteristic parameters such as pore size, coordination number, pore-throat ratio, and wettability on microscopic remaining oil after polymer flooding, thereby quantifying the types of remaining oil.

Quaking aspen (Populus tremuloides Michx.) landscapes are valued for their biodiversity, water retention, fire mitigation, aesthetics, and recreation opportunities. Across North America, some aspen populations are experiencing population declines as they face uninhibited ungulate browsing, drought, fire suppression, insects, disease, and inappropriate management. Increased human development and recreational use within aspen landscapes can serve as additive stressors, though there is a dearth of literature examining these elements. At a popular recreational area in Utah, USA, identifying the cause of apparent decline within a larger aspen community is complicated by development upstream and recreation-related activities. We sought to: 1) assess the overall condition of the aspen at the site, 2) understand key variables that influence aspen conditions, and 3) elucidate how aspen fitness varies across the site. We collected data from forty-five plots using established aspen sampling methods, including ungulate presence, tree characteristics, soil chemistry, and environmental descriptors. Results suggest that a combination of higher levels of browsing and elevated soil sodium may be causing premature mortality and limiting aspen recruitment in a portion of the study area. These findings will inform future management at this site, as well as similar recreational forest settings experiencing compound stressors.

Assessing observation noise is a critical step in the development of a stochastic model for GNSS navigation and positioning. This process ensures that the statistical properties of the observational data are accurately characterized, leading to more reliable and precise positioning results. Traditionally, the one sigma values for observation noise, 0.3 m for code and 3 mm for carrier phase, alongside elevation-dependent weighting schemes, have been standard. However, these may no longer be suitable due to significant advancements in GNSS systems, receivers, and antennas. Previous research predominantly focused on code type and PPP techniques, often limited by the inability to separately assess observation types across different frequency bands due to ionospheric delay. Furthermore, these studies were generally constrained by limited experimental data. This research advocates for the use of ultra-short baselines to eliminate atmospheric delay and other error sources, providing a detailed assessment of observation noise for various frequency bands, GNSS systems, and receiver & antenna types over an extensive period and across multiple baselines. The findings suggest a need to reconsider traditional one sigma values and elevation-dependent weighting schemes for current applications.

In recent years, ESG (environmental, social, governance) has emerged as a critical investment concept. Its goal is to create value for both shareholders and society, encouraging companies to optimize social value. However, the exploration and research into "the proportion of firms ex-porting and the pathways through which the environmental, social, and governance activities of carbon-intensive firms influence firms' financial performance" remains largely unexplored. This study establishes a research framework within this context, utilizing listed Chinese manufactur-ing companies as the research subjects. Employing a fixed-time, fixed-industry, two-way fixed-effects model methodology, it delves into the relationship between ESG ratings, the pro-portion of firms' exports, and firms' financial performance through panel regression modeling. This study emphasizes the moderating role of carbon-intensive firms in the relationship. Find-ings indicate that both enterprise export proportions and carbon-intensive firms significantly affect the correlation between corporate ESG activities and financial performance. This has im-plications for investors, company management, policymakers, and regulators. Based on these findings, we propose policy recommendations at corporate and governmental levels to enhance ESG significance, strengthen corporate governance, and promote continuous ESG advancement. The study provides micro-level evidence of the interaction among ESG ratings, export ratios, carbon-intensive enterprises, and corporate performance, empowering investors to make in-formed decisions.

A finite element model of 100m X-BOW polar exploration cruise is established. The entire ship frequency response analysis was carried out, comparing the simulated values with the test values, the maximum error is 22%, but only 0.24mm/s difference, the error can be ignored from the perspective of comfort, therefore, the simulation results meet the requirements of engineering accuracy and verify the effectiveness of the model. According to the solution method for global modal equivalent mass, combing the spatial distribution principle of local modal mass, the method for solving the equivalent mass of a single local mode in mixed mode is proposed, the equivalent mass of the local vibration region of 100m X-BOW polar exploration cruise ship is solved by this method, tuned mass dampers mass ratio parameters are calculated using the equivalent mass. According to the analysis, tuned mass dampers has 31dB vibration absorption effect at 13.4Hz when the mass ratio is 0.05, it also has certain control effect at 10Hz and 18.8Hz, the control effect is 3dB and 2dB respectively, the overall control frequency band is flat and robust.

In the field of railroad safety, effective detection of surface cracks is critical, necessitating reliable, high-speed non-destructive testing (NDT) methods. This study introduces a hybrid Eddy Current Testing (ECT) probe, specifically engineered for railroad inspection, to address the common issue of ’lift-off noise’ due to varying distances between the probe and test material. Unlike traditional ECT methods, this probe integrates transmit and differential receiver coils, aiming to enhance detection sensitivity and minimize lift-off impact. The study optimizes ECT probes employing different driver coils, emphasizing three main objectives: a) quantitatively evaluating each probe using signal- to-noise ratio (SNR) and outlining a real-time data processing algorithm based on SNR methodology; b) exploring the frequency range proximal to the electrical resonance of the receiver coil; c) examining sensitivity variations across varying lift-off distances. The experimental outcomes indicate that the newly designed probe with figure 8-shape driver coil significantly improves sensitivity in detecting surface cracks on railroads. It achieves an impressive SNR exceeding 100 for defects with minimal dimensions of 1 mm in width and depth. Simulation results closely align with experimental findings, validating the investigation of optimal operational frequency and lift-off distance for selected probe performance, determined to be 0.3 MHz and 0.5 mm, respectively. The realization of this project would lead to notable advancements in enhancing railroad safety by improving crack detection efficiency.

The high reliable correlations between CBR and DCP in general proposed are presented in this paper. We analyzed the test data and correlations from many researchers to find the best equation for prediction the CBR from DCP test. The findings show that all correlations from existing paper are based on local material and cannot apply to soil in a different location in general purpose. New correlations between CBR and DCP were proposed and validated in this paper for general uses. The validation confirmed that these new correlations can predict well with higher R2.

This research aims to deepen the understanding of the relationship between conductivity and morphology in polypyrrole (PPy) via a comparison of the bipolaron to polaron ratios with a focus on the C-H deformation area. PPy samples were synthesized with different surfactants: sodium dodecyl sulfate (SDS), cetyltrimethylammonium bromide (CTAB), and tween 80 (TW). The study revealed that SDS significantly altered the bipolaron and polaron in C-H deformation region and showed higher conductivity than other surfactants. Notably, the morphological shifts to a sheet-like structure when using ammonium sulfate (APS) contrasted with the particle-like form observed with ferric chloride (FeCl3). These results showed that if the oxidant changed, the bi-polaron and polaron ratios in C-H deformation were unrelated to PPy morphology. However, this work showed a consistent relationship between SDS use, the bipolaron and polaron ratios in the C-H deformation, and the conductivity properties. Moreover, the natural positive charge of PPy and negatively charged SDS molecules may lead to an electrostatic interaction between PPy and SDS. This work assumes that this interaction might cause the transformation of polaron to bipolaron in the C-H deformation region, resulting in improved conductivity of PPy. This work offers more support for the future investigation of PPy characteristics.

Olive trees have a unique reproductive pattern marked by biennial fruiting. This study delves into the repercussions of alternate fruit bearing on the water relations of olive trees and the associated ecophysiological mechanisms. The experiment spanned two consecutive years: the "ON" year, characterized by a high crop load, and the "OFF" year, marked by minimal fruit production. Key ecophysiological parameters, including sap flow, stomatal conductance, and photosynthetic rate, were monitored in both years. Pre-dawn water potential was measured using continuous stem psychrometers and the pressure chamber technique. Biochemically, non-structural carbohydrate concentrations (starch, sucrose, and mannitol) and the carbon-stable isotope ratio (δ13C) in olive leaves were examined. Results unveiled heightened leaf gas exchange during the "ON" year, leading to increased water consumption and photosynthetic rates. This escalated water usage during the "ON" year significantly reduced leaf water potential. Sucrose and starch concentrations were notably elevated in the "ON" year, with no significant impact on mannitol concentration. Regarding the carbon stable isotope ratio, leaves from the "OFF" year exhibited significantly higher δ13C abundance, indicative of heightened resistance to the CO2 pathway from the atmosphere to carboxylation sites compared to the "ON" year plants.

Increasing CO2 concentration ([CO2]) in atmosphere decreases mineral nutrients concentration in crops whereas increasing water use efficiency (WUE) especially in drought conditions. Partial root-zone irrigation (PRI) could stimulate soil nutrient mineralization and improve crop nutrient status. Yet the effect of PRI combined with elevated CO2 concentration (e[CO2]) on the element stoichiometry of tomato leaves remains unknown. This study was to investigate the responses of leaf mineral nutrients status and element stoichiometric ratio in tomato grown at PRI exposed to e[CO2]. Tomato plants (cv. Ailsa Craig) were grown in pots in climate-controlled growth chambers with ambient [CO2] (a[CO2], 400ppm) and elevated [CO2] (e[CO2] 800ppm), respectively. Three irrigation regimes (IR) i.e. full irrigation (FI), deficit irrigation (DI) and partial root-zone irrigation (PRI) were applied to tomato plants at flowering stage. The result showed that plants exposed to both reduced irrigations had a similar biomass, an enhanced root growth including greater root to shoot ratio (R/S), root length (RL), surface area (RS), volume (RV) and specific length (RSL), and an improved WUE under e[CO2]. Compared to a[CO2], e[CO2] growth environment resulted in a similar leaf [C], [K] and [Mg], leaf C/K and C/Mg, increased leaf [Ca], [S] and leaf C/N, C/P and N/P, but decreased leaf [N], [P], leaf C/Ca, C/S and N/K at PRI. Additionally, under e[CO2], PRI showed an increase in leaf [C], [N] and [S], no decrease in leaf [K], Ca], [Mg], [S] and [15N], but a decrease in leaf C/N and C/S as compared with FI. Conclusively, PRI had the ability to alleviate the negative effects on mineral nutrient concentrations and maintain or improve most leaf element stoichiometric ratios under e[CO2]. Therefore PRI would be a practicable irrigation for optimizing WUE and nutrient status in tomato leaves in a future freshwater-limited and higher CO2 environment.

Fiber coupling efficiency is one of the key technical indicators of atmospheric laser communication, which directly affects the communication system BER. According to the optical fiber coupling efficiency model, the optical fiber coupling model under atmospheric slant link is established, and the relationship between wavelength, zenith angle, receiving aperture, altitude and coupling efficiency is studied through numerical simulation. Based on the principle of adaptive optics turbulence correction, the relationship between fiber coupling efficiency and adaptive optics order is established. A fast method for estimating the coupling efficiency based on Strehl ratio is proposed. According to the principle of laser communication system, the semi-physical simulation experimental system of atmospheric slant-range channel coupling efficiency is constructed, and the coupling efficiency test and analysis are completed.

In this study, long-term mortality effects associated with exposure to PM10, PM2.5, BC (black carbon), and NOx were analyzed in a cohort in southern Sweden during the period from 1991‒2016. Participants (those residing in Malmö, Sweden, born between 1923‒1950) were randomly recruited from 1991‒1996. At enrollment, 30,438 participants underwent a health screening, which consisted of questionnaires about lifestyle and diet, a clinical examination, and blood sampling. Mortality data were retrieved from the Swedish national cause of death register. The modeled concentrations of PM10 (particles with an aerodynamic diameter smaller than or equal to 10 µm), PM2.5 (particles with an aerodynamic diameter smaller than or equal to 2.5 µm), BC (black carbon), and NOx (nitrogen oxides) at the cohort participants' home addresses were used to assess air pollution exposure. Cox proportional hazard models were used to estimate the associations between long-term exposure to PM10, PM2.5, BC, and NOx and the time until death among the participants during the period from 1991‒2016. The hazard ratios (HRs) associated with an interquartile range (IQR) increase in each air pollutant were calculated based on the exposure lag windows of the same year (lag0), 1‒5 years (lag1‒5), and 6‒10 years (lag6‒10). Three models were used with varying adjustments for possible confounders including both single-pollutant estimates and two-pollutant estimates. With adjustments for all covariates, the HRs for PM10, PM2.5, BC, and NOx in the single-pollutant models at lag1‒5 were 1.06 (95% CI: 1.02‒1.11), 1.01 (95% CI: 0.95‒1.08), 1.07 (95% CI: 1.04‒1.11), and 1.11 (95% CI: 1.07‒1.16) per IQR increase, respectively. The HRs were in most cases decreased by the inclusion of a larger number of covariates in the models. The most robust associations were shown for NOx, with statistically significant positive HRs in all models. An overall conclusion is that road traffic-related pollutants had a significant association with mortality in the cohort.

This experimental study examined the application effect of polycaprolactone (PCL), an organic resin material with excellent elasticity and ductility, on improving the mechanical performance of cellulose nanocrystal (CNC) cement composites. To analyze the effect, a test specimen containing CNC and PCL mixed, containing only CNC, and a control (plain) specimen containing nothing were compared. PCL was compared according to its shape, and in the case of Granules, which is the basic shape, interfacial adhesion with cement was not achieved, so a DCM solution was used to dissolve and use the Granules form. As a method for bonding PCL to the CNC surface, the CNC surface was modified using 3-aminopropyltriethoxysilane (APTES), and surface silylation was confirmed through Fourier transform infrared spectroscopy(FT-IR) analysis. To evaluate the dispersibility according to the application of PCL to the modified CNC, particle size analysis (PSA) and zeta potential analysis were performed according to the PCL mixing amount (0.1, 0.3, 0.5, and 1 vol.% compared with those of CNC) and size distribution. Through the zeta potential value, the highest dispersion stability was shown at 1 vol.%. The cohesive force of CNC was low and the dispersion stability was high according to the application of PCL. According to the results of the dispersion stability evaluation, the degree of hydration of the dissolved PCL 1 vol.%, CNC-only specimens, and plain specimens were analyzed. Hydration products increased by increasing the degree of hydration in the unhydrated area. However, the incorporation of PCL showed a low degree of hydration, and the analysis of strength characteristics also showed a decrease of approximately 27% compared with that of plain specimens. This was because the bonding with SiO2 was not smooth owing to the solvent, thus affecting internal hydration. To investigate the effect of the PCL shape, the compressive and flexural strength characteristics were compared using PCL powder as an additional parameter. The compressive and flexural strength values were improved by approximately 54% and 26%, respectively, compared with those of the plain specimen. Scanning electron microscopy (SEM) analysis determined that the filler effect that made the micropore structure denser, affected the mechanical performance improvement.

Identifying the SARS-CoV-2 virus has been a unique challenge for the scientific community. In this paper, we discuss a practical solution to help guide clinicians with interpretation of the probability that a positive, or negative, COVID-19 test result indicates an infected person, based on their clinical estimate of pre-test probability of infection.The authors conducted a small survey on LinkedIn to confirm that hypothesis that that the clinical pre-test probability of COVID-19 increases relative to local prevalence of disease plus patient age, known contact, and severity of symptoms. We examined results of PPA (Positive Percent Agreement, sensitivity) and NPA (Negative Percent Agreement, specificity) from 73 individual laboratory experiments for molecular tests for SARS-CoV-2 as reported to the FIND database ¹, and for selected methods in FDA EUA submissions^2,3. Authors calculated likelihood ratios to convert pre-test to post-test probability of disease and designed an online calculator to create graphics and text to report results. Despite best efforts, false positive and false negative Covid-19 test results are unavoidable^4,5. A positive or negative test result from one laboratory has a different probability for the presence of disease than the same result from another laboratory. Likelihood ratios and confidence intervals can convert the physician or other healthcare professional’s clinical estimate of pre-test probability to post-test probability of disease. Ranges of probabilities differ depending on proven method PPA and NPA in each laboratory. We recommend that laboratories verify PPA and NPA and utilize a the “Clinician’s Probability Calculator” to verify acceptable test performance and create reports to help guide clinicians with estimation of post-test probability of COVID-19.

Backgroundː Previous studies have shown that both serum creatinine and D-dimer levels were associated with atherosclerotic coronary artery disease (CAD). We aimed to determine whether DCR is associated with coronary Gensini score in patients with ST-elevation myocardial infarction (STEMI). Methodsː 337 STEMI patients with complete D-dimer and creatinine and other necessary information were included in the analysis. According to the values of the DCR, patients were divided into the lower DCR group (DCR ≤ 1.42, n = 173) and the higher DCR group (DFR > 1.42, n = 174), and the differences between the two groups were compared. Multivariate linear and multivariate logistic regression analyses were performed to determine independent predictors of Gensini score. Resultsː High DCR group had higher Gensini score compared with low DCR group (P < 0.05). DCR was positively correlated with Gensini score (r=0.493, P < 0.001). Multiple linear regression analysis showed that Previous MI (r=11.312, P=0.035) and DCR (r=5.129, P<0.001) were independent risk factors associated with Gensini score. Multivariate logistic regression analysis showed that, compared to the group 1, DCR is independent risk factor for Group 2, Group 3, Group 4 (P <0.001). DCR is positively correlated with coronary Gensini score in STEMI patients and can be used as an independent predictor of higher Gensini score. Conclusionsː As a new and useful clinical marker, DCR is positively correlated with coronary Gensini score in STEMI patients and can be used as an independent predictor of higher Gensini score.

The influence of the Fe2O3 addition amount on the dephosphorization of hot metal at 1623 K with the slag of the low basicity (CaO/SiO2) of about 1.5 was investigated by using high-temperature laboratorial experiments. With increasing the Fe2O3 addition amount, the contents of [C], [Si], [Mn] and [P] in hot metal at the end of dephosphorization decrease, and the corresponding removal ratios increase. The P2O5 content in slag increases, and the CaO and SiO2 contents in slag decrease. The phosphorus mainly exists in the form of the nCa2SiO4-Ca3(PO4)2 solid solution in the phosphorus-rich phase and the value of coefficient n decreases from 20 to 1 with increasing the Fe2O3 addition amount from 5 g to 30 g. With increasing the Fe2O3 addition amount, the oxygen potential and activity at the interface between the slag and hot metal increase. When the oxygen potential and the oxygen activity at the interface are greater than 0.72×10-12 and 7.1×10-3, respectively, the dephosphorization ratio begins to increase rapidly. With increasing the Fe2O3 addition amount to 30 g, the ratio of the Fe2O3 addition amount to theoretical calculation consumption is around 175%, and the dephosphorization ratio reaches the highest value of 83.3%.

The antibiotic residues and pathogenic resistance against the drug are very common in poultry due to usage of antibiotics in their feed. It is the need of the time to use natural feed additives as effective alternatives instead of synthetic antibiotic. The aim of this study was to investigate the immune response of Nigella sativa and Curcuma longa in broilers under biological stress against Pasteurella multocida. The total 100, one-day old chicks were divided into 5 groups. The Groups 1 and 2 were served as control negative and control positive. Both control groups were receiving simple diet without any natural feed additives but infection was given in Group 2 at day 28 with the dose of 5.14×107 CFU by IV. Groups 3A & 3B were offered 2% seed powder of Nigella sativa, Groups 4A & 4B were offered Curcuma longa 1% in powdered form and Group 5A & 5B were offered both Curcuma longa 1% & Nigella sativa 2% in feed from day 1 and groups 3B, 4B and 5B were challenged with Pasteurella multocida. The Haemagglutination inhibition titter against Newcastle Disease Virus (NDV), feed conversion ratio, mortality, gross and histopathology were studied. The results of this study revealed that haemagglutination inhibition titers against NDV were highly significant (P< 0.05) in treated groups, highest titers (3A 6.8, 3B 6.4 and 5A 7.2) were obtained from treated Group. The feed conversion ratio (FCR) of Nigella sativa + Curcuma longa treated Groups (5A 1.57 and 3A 1.76) were higher as compared to other non-treated groups. The gross and histopathological changes were much severe in control positive, but less changes were seen in treated groups. Therefore, we recommend that natural feed additives; black cumin (Nigella sativa) and turmeric (Curcuma longa) act as immune enhancer in broilers against Pasteurella multocida.

Large intelligent surfaces (LIS) promises not only to improve the signal to noise ratio, and spectral efficiency but also to reduce the energy consumption during the transmission. We consider a base station equipped with an antenna array using the maximum ratio transmission (MRT), and a large reflector array sending signals to a single user. Each subchannel is affected by the Rayleigh flat fading, and the reflecting elements perform non-perfect phase correction which introduces a Von Mises distributed phase error. Based on the central limit theorem (CLT), we conclude that the overall channel has an equivalent Gamma fading whose parameters are derived from the moments of the channel fading between the antenna array and LIS, and also from the LIS to the single user. Assuming that the equivalent channel can be modeled as a Gamma distribution, we propose very accurate closed-form expressions for the bit error probability and a very tight upper bound. For the case where the LIS is not able to perform perfect phase cancellation, that is, under phase errors, it is possible to analyze the system performance considering the analytical approximations and the simulated results obtained using the well known Monte Carlo method. The analytical expressions for the parameters of the Gamma distribution are very difficult to be obtained due to the complexity of the nonlinear transformations of random variables with non-zero mean and correlated terms. Even with perfect phase cancellation, all the fading coefficients are complex due to the link between the user and the base station that is not neglected in this paper.

Since identified as the pathogen responsible for an outbreak of severe respiratory distress in Wuhan, China, the 2019-nCoV coronavirus has caused over 30M cases and 1M deaths globally. Sporadic cases were identified in several states in the US from early January, and large-scale community transmission is believed to have started in late February, leading to a first spike in COVID-19 deaths and overall mortality in late April, and a second spike later in the summer. I show here that the dynamics of the pandemic were different in different regions of the US, showing a north-south pattern, with a first pandemic wave mainly in northern regions, followed by a second wave mainly in southern regions. Analysis of overall mortality data shows that the increase in mortality correlates well with COVID-19 incidence in most regions, and that from April through August COVID-19 deaths accounted for a substantial proportion of all deaths in all parts of the US.

Soil water loss by evaporation influences the sodium adsorption ratio (SAR) of irrigation drainage water. Evaporation concentrates sodium and magnesium but calcite precipitation has a more complicated effect on soluble calcium and alkalinity. Here we propose a revised sodicity hazard assessment that quantifies the impact of evaporative water loss and calcite precipitation on drainage water SAR. This paper shows sodicity hazard is determined by the initial composition of irrigation water as originally suggested by previous researchers, and provide a simple, accurate way to identify the potential sodicity hazard of any irrigation water. In particular, the initial equivalent concentration of alkalinity and calcium determine the salinization pathway followed during evaporation. If the irrigation water alkalinity exceeds soluble calcium expressed as equivalent concentrations, drainage water SAR approaches an upper limit determined by the initial relative concentration of sodium and magnesium. If irrigation water alkalinity is less than soluble calcium, drainage water SAR approaches a lower limit determined by the initial calcium, magnesium and sodium. In both cases the SAR is scaled by the square root of the concentration factor √Fc quantifying soil water loss. To assess the impact of evaporation and calcite precipitation on the SAR and test the accuracy of the new sodicity hazard assessment, we evaluated data from previously published lysimeter studies. We plotted water composition boundaries for each source water, comparing these boundaries to the drainage water composition recorded in the lysimeter studies. As salinity increased by evaporation, each drainage water followed a distinct salinization path.

Liquefaction risk assessment is critical for the safety and economics of structures. As the soil strata of Ramsar area in north Iran is mostly composed of poorly graded clean sand and the ground water table is found at shallow depths, it is highly susceptible to liquefaction. In this study, a series of isotropic and anisotropic consolidated undrained triaxial tests are performed on reconstituted specimens of Ramsar sand to identify the liquefaction potential of the area. The specimens are consolidated isotropically to simulate the level ground condition, and anisotropically to simulate the soil condition on a slope and/ or under a structure. The various states of soil behavior are studied by preparing specimens at different initial relative densities and applying different levels of effective stress. The critical state soil mechanics approach for identifying the liquefaction susceptibility is adopted and the observed phenomena are further explained in relation to the micro-mechanical behavior. As only four among the 27 conducted tests did not exhibit liquefactive behavior, Ramsar sand can be qualified as strongly susceptible to liquefaction. Furthermore, it is observed that the pore pressure ratio is a good indication of the liquefaction susceptibility

The most cited evidence for (nonbaryonic) dark matter has been an apparent lack of visible mass to gravitationally support the observed orbital velocity of matters in rotating disk galaxies. Yet measurement of the mass of celestial objects cannot be straightforward, requiring theories derived from the known physical laws along with some empirically established semi-quantitative relationship. The most reliable means for determining the mass distribution in rotating disk galaxies is to solve a force balance equation according to Newton’s laws from measured rotation curves, similar to calculating the Sun’s mass from the Earth’s orbital velocity. Another common method to estimate galactic mass distribution is to convert measured brightness from surface photometry based on empirically established mass-to-light ratio. For convenience, most astronomers commonly assumed a constant mass-to-light ratio for estimation of the so-called “luminous” or “visible” mass, which should not be expected accurate. The mass determined from rotation curve typically exhibit an exponential-like decline with galactrocentric distance, qualitatively consistent with observed surface brightness. This fact scientifically suggests variable mass-to-light ratio of baryonic matter in galaxies without the need for dark matter.

As a renewable industrial crop, Miscanthus offers numerous advantages, namely high photosynthesis activity (as a C4 plant) and exceptional CO2 fixation rate. These properties make Miscanthus very attractive for industrial exploitation, such as lignin generation. Here, we present a systematic study analyzing the correlation of the lignin structure with Miscanthus genotype and plant portion (stem versus leaf). Specifically, the ratio of the three monolignols and corresponding building blocks as well as the linkages formed between the units have been studied. Depending on the Miscanthus genotype and plant component (leaf versus stem), correlations between chemical structure and properties of the lignins have been determined, i.e. correlations in molecular weight, polydispersity and decomposition temperature. Lignin isolation was performed using non-catalyzed organosolv pulping and the structure analysis includes NREL, FTIR, UV-Vis, HSQC-NMR, TGA, pyrolysis GC/MS. Structural differences were found for stem and leaf-derived lignins. Compared to beech wood lignins, Miscanthus lignins possess lower molecular weight and narrow polydispersities (< 1.5 Miscanthus vs. > 2.5 beech) corresponding to improved homogeneity. In addition to conventional univariate analysis of FTIR spectra, multivariate chemometrics revealed distinct differences for aromatic in-plane deformations of stem versus leaf-derived lignins. These results emphasize the potential of Miscanthus as low-input resource and Miscanthus-derived lignin as promising agricultural feedstock.

In the paper, the author presents explicit and unified expressions for a sequence of improper integrals in terms of the beta functions and the Wallis ratios. Hereafter, the author derives integral representations for the Catalan numbers originating from combinatorics.

In recent experimental studies, we reported the aggravating effects of Asian sand dust (ASD) on male reproductive function in mice. However, the effects of fetal ASD exposure on male reproductive function have not been investigated. The present study investigated the effects of fetal ASD exposure on reproductive function in male offspring. Using pregnant CD-1 mice, ASD was administered intratracheally on days 7 and 14 of gestation, and the reproductive function of male offspring was determined at 5, 10, and 15 weeks after birth. The secondary sex ratio was significantly lower in the fetal ASD-exposed mice than in the controls. Histologic examination showed partial vacuolation of seminiferous tubules in immature mice. Moreover, daily sperm production (DSP) was significantly less in the fetal ASD-exposed mice than in the controls. DSP in the fetal ASD-exposed mice was approximately 10% less than the controls at both 5 and 10 weeks. However, both the histologic changes and the DSP decrease were reversed as the mice matured. These findings suggest that ASD exposure affects both the fetal development and the reproductive function of male offspring. In the future, it will be necessary to clarify the onset mechanisms of ASD-induced male fetus death and male reproductive disorders.

This study investigates the intricate relationships between happiness, sustainability, and cultural values across 74 countries. Utilizing a multidimensional scaling (MDS) and K-means clustering approach, we analyze six happiness indices alongside the Sustainable Development Goals Index (SDGI). Our findings indicate a positive correlation between economic development, social progress, and elevated levels of both happiness and sustainability. Nevertheless, instances like the United States highlight the necessity of alternative methodologies, highlining classification of nonlinear models. The MDS analysis identifies four distinct clusters of countries, each demonstrating similar profiles in terms of happiness, sustainability, and cultural values, as per Inglehart's framework. This clustering underscores the necessity for a comprehensive perspective that integrates economic, social, and cultural dimensions to produce robust results and mitigate disparities or contradictions in subjective measures like the World Happiness Score. Future research should explore the impact of institutional frameworks, governance models, and social capital. Additionally, longitudinal studies are needed to examine how these relationships evolve in response to global challenges. We acknowledge the limitations related to data heterogeneity, the subjectivity of cluster analysis, and the exclusion of outliers, emphasizing the need for further research to enhance the generalizability and robustness of these findings.

Background and Aims: Stroke is a leading cause of seizures and epilepsy in adults, but current guidelines lack strong recommendations for treating post-stroke seizures (PSE). This study aims to demonstrate the safety and efficacy of lacosamide combined with non-vitamin K antagonist oral anticoagulants (NOACs) in patients with PSE and atrial fibrillation (AF). Methods: In this prospective longitudinal study, 53 patients with PSE and AF, admitted from 2022 to 2023, received NOACs for AF management and lacosamide for seizure control. A control group of 53 patients with cardioembolic stroke, receiving NOACs, was matched by age, sex, and NIHSS scores to ensure comparability. Results: Over 24 months, 16 patients in the study group and 15 in the control group experienced new embolic events, with no significant difference between groups. Seizure control improved significantly in the study group, with reduced frequency and severity. No severe adverse effects from lacosamide were observed. Conclusions: The combination of NOACs and lacosamide is a safe and effective treatment for patients with AF and PSE, not increasing the risk of recurrent ischemic or hemorrhagic events. Further studies with larger sample sizes and longer follow-ups are needed to confirm these findings and optimize treatment protocols.

Education is one of the most important tools available to policymakers and non-governmental bodies to promote a change in the behavior of society and to address the climate crisis, in line with the 4^th and 13^th Sustainable Development Goals of the United Nations 2030 Agenda. Project-based learning (PBL) addresses real and global challenges and allows the academic and professional formation of students. As part of the reflection stage of the educational action research method using the Business Canvas Model (BMC), pedagogic deficiencies were identified in the PBL and a didactic proposal was elaborated to emulate the interaction of students with the ecosystems of society. A prototype for improving the management of organic manures as soil amendments was initially developed, to provide the students with a quick start on the first steps of the proposed project. In the 10 sessions designed for the PBL (Make it happen!), the students elaborate a more sophisticated artifact in response to the demands of potential clients, as per the outcomes of the primary market research (5^th session). Active teaching methods and tools, such as a modified template of the BMC with the Rumsfeld’s matrix, aid the metacognition of students and their competences development. In a double session of the PBL, the primary market research is organized with key stakeholders of the agroindustry to enquire about the feasibility of the implementation of the technological solution and the logistics at farm level. Finally, the evaluation relies on the suitability of the upgraded prototype to respond customers’ demands.

It is unclear how important it is to reduce fluoroquinolone consumption in the general population to prevent the spread of fluoroquinolone resistance in Neisseria gonorrhoeae (bystander selection). Methods We assessed bystander selection by using Spearman’s correlation to assess if the country-level prevalence of fluoroquinolone resistance in N. gonorrhoeae was correlated with the prevalence of fluoroquinolone resistance in four other gram-negative species - Acinetobacter baumannii, Escherichia coli, Klebsiella pneumoniae and Pseudomonas aeruginosa. Results Fluoroquinolone resistance in N. gonorrhoeae was positively associated with homologous resistance in all 4 species - A. baumanii. (ρ=0.61, P=0.0003, E. coli (ρ=0.67, P<0.0001), K. pneumoniae (ρ=0.52, P=0.0004) and P. aeruginosa (ρ=0.40, P=0.0206). Positive associations were also found between the national prevalence of fluoroquinolone resistance and fluoroquinolone consumption in the general population in the preceding year for 4 of the 5 species. Conclusions Gonococcal fluoroquinolone resistance can be productively viewed as being part of a syndemic of fluoroquinolone resistance. Strengthening antimicrobial stewardship programs may help retard the spread of fluoroquinolone resistance in N. gonorrhoeae.

The progressive impairment analysis in gait from neurological diseases patients such as Hereditary Ataxias (HA) has been carried out using gait data collected with movement sensors. This research is focused on finding the minimum amount required of gait features to recognize efficiently and less intrusive way, HA patients based on data collected with iPhone movement sensors placed on the ankles from 14 HA patients and 14 healthy people. A twofold proposal is made , first a local minimum prominent peak criterion to find out the starting point of each stride, to get 10-stride window about which 56 spatial-temporal features are derived; second a search strategy based on Hill Climbing algorithm to reduce the number of gait features and sensors. The main results were the findings that with two gait patterns a 96% of classification accuracy was achieved by using K-Nearest Neighbors (KNN) and Multi-Layer Perceptron (MLP) algorithms, but in addition, MLP only right ankle sensor patterns were required which also allows to reduce the intrusion.

Various type of soils have been identified based on their electrical and magnetic properties, especially with regards to peat soils. Peat soils are commonly considered as partly decomposed vegetation. In this study, electrical and magnetic properties have been used in K-means clustering to identify layers of peat soils. K-means clustering is a partitioning method that treats observations in the data. Data cores were obtained at every centimeter and examined for their electrical conductivity (σ) and magnetic susceptibility (χ_m) properties. A 291 cm core was obtained at Tegal Arum Village in South Kalimantan, Indonesia. The K-means clustering results indicate two different layers at 148 cm, and this is supported by loss on ignition (LOI) measurements. In the first layers, a 87.65% LOI was found associated with peat soils (above 248 cm). Whereas, in the second layers, there was a 26.11% LOI associated with mineral soils (below 248 cm). The results of this study using K-means clustering can be used to delineate soil layers.

Piezoelectric c-axis oriented zinc oxide (ZnO) thin films, from 1.8 up to 6.6 µm thick, have been grown by radio frequency magnetron sputtering technique onto fused silica substrates. A delay line consisting in two interdigital transducers (IDTs) with wavelength λ = 80 µm was photolith-ographically implemented onto the surface of the ZnO layers. Due to the IDTs split finger con-figuration and metallization ratio (0.5), the propagation of both the fundamental, third and nineth harmonic Rayleigh waves is excited; also, three leaky surface acoustic waves (SAWs) were detected travelling at velocity close to that of the longitudinal bulk wave in SiO2. The acoustic waves propagation in ZnO/fused silica was simulated by using 2D finite-element method (FEM) tech-nique to identify the nature of the experimentally detected waves. It turned out that, in addition to the fundamental and harmonic Rayleigh waves, also high-frequency leaky surface waves are ex-cited by the harmonic wavelengths; such modes are identified as leaky-Sezawa (LS) waves under cut-off. The velocity of all the modes was found in good agreement with the theoretically calcu-lated values. The existence of a low-loss region for the Sezawa wave below the cut off was theo-retically predicted and experimentally assessed.

The inherent capabilities of the K-means++ algorithm to approximate system dynamics within complex systems are subjected by constructing a network structure that captures interconnections among identified components, extending its original purpose as a data clustering method and transforming it into a tool for systems analysis. Leveraging advanced measurement technologies and sophisticated data collection systems, the K-means++ algorithm unveils hidden relationships among components and identifies critical elements. This study explored the algorithm's potential, facilitating the identification of critical components to enhance system operation, control, optimization, and decision-making and examining the practicality and resiliency of the method in real-world application with noisy and limited data. A case study conducted on power systems (IEEE 39-bus and IEEE 300-bus systems) exemplifies K-means++'s capacity to accurately identify critical components and approximate system dynamics, supported by performance metrics affirming its effectiveness and robustness in system analysis through measurements of bus similarity within clusters based on standard deviation and comparison of net tie-line flows in equivalent networks with the original network across scenarios. Performance metrics, including the Silhouette Score, Davies-Bouldin Index, and Variation of Information (VI) score, further validated K-means++'s performance, yielding reliable and consistent results.

As distinct human societies, three unique intentional communities are investigated regarding their preferred consensus decision-making practices. It is Identified that each has adopted a different form of consensus decision-making to solve potential group-wide interpersonal conflict. The individual attributes of these three consensus decision-making practices are considered, both from the perspective of maintaining group stability and in relation to individual member's mental health. The communities are a Canadian self-directed public senior elementary and secondary school, an annual English conference for those self-identifying as on the autistic spectrum, and a self-producing Korean popular music (K-pop) group. It is found that the intentional community and participants’ mental health are sustained regarding each of the three consensus decision-making practices. Nevertheless, the resulting decisions generate various stresses within the communities, both as a whole and concerning the individual members. To retain group cohesion and maintain individual mental health, these stresses must be recognized and understood by participants. The novel finding of this research is that, dependent on the time available for decision-making, and the members’ perspective adopted, intentional communities might practice more than one form of consensus decision-making and still support both group cohesion and individual mental health, maintaining the democracy of these distinct societies.

Finding anomalies in the real-time system is recognized as one of most challenging study in information security. It has so many applications like IoT, and Stock-Market. In any IoT system the data generated are real-time, and temporal in nature. Since due to the extreme exposure to Internet and interconnectivity of devices, the IoT systems often face issues like fraud, anomalies, intrusions etc. Discovering anomaly in such domain can be interesting. Clustering and rough set theory have been tried in many cases. Considering the time-stamp associated with IoT data, time-dependent patterns like periodic clusters can be generated which could be helpful for the efficient detection of anomalies by providing more in-depth analysis of the system. In this paper, a mixed method comprising of nano topology, a modified k-means clustering and an interval superimposition technique is used for finding fuzzy periodic clusters in the subspace generated by the nano topology. For every clusters there will be an associated sequence of time-intervals where it exists. The sequence time-intervals accompanying with each clusters may exhibit some remarkable patterns. For example, there may exist different types of periodicity namely yearly, monthly, daily, and hourly etc. For finding such fuzzy periodicity, an operation called interval-superimposition has been used. The time-intervals associated with each cluster are superimposed if they have reasonable overlapping. Each superimposed time-interval generates a fuzzy time-interval. The data instances are thought to be anomalous if they either belong to sparse clusters or don't belong to any clusters. The efficacy of the method can be assessed by means of both time-complexity analysis and comparative studies with existing clustering-based anomaly detection algorithms with a real-life and a synthetic dataset. It can been found experimentally that our method can extract anomaly with 98% of accuracy and it runs cubic time approximately.

Falls are extremely damaging to the elderly. The number of elderly who have experienced falls has increased over the years, several of the elderly stay alone or in in badly maintained elderly homes. This makes a low-cost fall detection system a necessity. There has been huge improvements in terms of IoT systems, ML algorithms. Varied data sets have been collected across the world for fall detection. These data sets have a very little in common among them, in terms of user demographics, sensors used, the ADL and Fall activities Hence in this paper we present a data set that has wide user demographics, we used various sensors – such as accelerometer, gyroscope, magnetometer and hear rate. We used wrist worn sensors to collect data. In this paper we present a detailed analysis of the data set we collected using common ML algorithms such as – Naïve Bayes (NB), K Nearest Neighbor (KNN), Logistic Regression (LR), Random Forest (RF) and Support Vector Machines (SVM). We analyzed the performance of these algorithms for variations in accuracy with respect to age, gender, height, weight and health issues and we have identified outliers by analyzing each incorrect prediction. This paper provides the complete details of the data collection methodology, The methods used for analysis and presents the results of analysis in complete detail.

Age estimation in dental radiographs Orthopantomography (OPG) is a medical imaging technique that physicians and pathologists utilise for disease identification and legal matters. For example, for estimating post-mortem interval, detecting child abuse, drug trafficking, and identifying an unknown body. Recent development in automated image processing models improved the age estimation's limited precision to an approximate range of +/- one year. While this estimation is often accepted as accurate measurement, age estimation should be as precise as possible in most serious matters, such as homicide. Current age estimation techniques are highly dependent on manual and time-consuming image processing. Age estimation is often a time-sensitive matter in which the image processing time is vital. Recent development in Machine learning-based data processing methods has decreased the imaging time processing; however, the accuracy of these techniques remains to be further improved. We proposed an ensemble method of image classifiers and transfer learning techniques to enhance the accuracy of age estimation using OPGs from one year to a couple of months (1-3-6). This hybrid model is based on convolutional neural networks (CNN) and K nearest neighbours (KNN). The hybrid (HCNN-KNN) model was used to investigate 1,922 panoramic dental radiographs of patients aged 15 to 23. These OPGs were obtained from the various teaching institutes and private dental clinics in Malaysia. To minimise the chance of overfitting in our model, we used the principal component analysis (PCA) algorithm and eliminated the features with high correlation. To further enhance the performance of our hybrid model, we performed systematic image pre-processing. We applied a series of classifications to train our model. We have successfully demonstrated that combining these innovative approaches has improved the classification and segmentation and thus the age-estimation outcome of the model. Our findings suggest that our innovative model, for the first time, to the best of our knowledge, successfully estimated the age in classified studies of one year old, six months, three months and one-month-old cases with accuracies of 99.98, 99.96, 99.87, and 98.78 respectively.

Insecticides with novel modes of action are required to complement the pyrethroids currently relied upon for controlling malaria vectors. One example of this is the neonicotinoid clothianidin, which is found in SumiShield™ 50WG used in indoor residual spraying (IRS). In a preliminary experiment, mortality in insecticide susceptible and resistant An. gambiae adults exposed to SumiShield™ 50WG-treated filter papers reached 80% by 3-days post-exposure and 100% by 6-days post-exposure. Next, cement, wood, and mud tiles were treated with SumiShield™ 50WG or K-Othrine® WG250 (deltamethrin IRS formulation) and insecticide resistant and susceptible Anopheles and Aedes were exposed to these surfaces periodically for up to 18-months. Pyrethroid resistant Cx. quinquefasciatus were also exposed at 9 months. Between exposures tiles were stored in heat and relative humidity conditions reflecting those found in the field. On these surfaces, SumiShield™ 50WG was effective at killing both susceptible and resistant An. gambiae for 18 months post-treatment, while mortality amongst the resistant strains when exposed to deltamethrin (K-Othrine® WG250) IRS was not above that of the negative control. Greater efficacy of SumiShield™ 50WG was also demonstrated against insecticide resistant strains of An. funestus compared to deltamethrin, though the potency was lower when compared with An. gambiae. In general, a higher efficacy of SumiShield™ 50WG was observed on cement and mud compared to wood. SumiShield™ 50WG demonstrated poor residual activity against Aedes aegypti and Culex quinquefasciatus. Overall, the results suggest SumiShield™ 50WG is well suited for malaria control.