The work aims to improve the battery performance in hybrid electric vehicles (HEVs) by reducing the vehicle speed. We develop a specific protocol for managing battery use and optimizing the energy consumption rate to achieve this goal. The protocol automatically controls the driving operation, avoiding incompatible driving patterns with energy-saving mode and performance improvement. The protocol is submitted to a simulation process to predict the energy rate lowering and battery performance enhancement. The proposed protocol applies to any hybrid electric vehicle type and route conditions since it uses vehicle mass, drag and rolling coefficients, and road slope as variable parameters to determine the minimum energy consumption rate. We run experimental tests to validate the simulation data and the proposed protocol. Furthermore, the protocol applies to variable starting vehicle speeds, from 10 to 50 km/h, corresponding to the current driving patterns, sport, normal, and eco, set up by car manufacturers. A reduction of 10% in vehicle speed in urban and peripheral routes achieves a minimum energy rate, enhancing battery management. Current vehicle speed shows a deviation from optimum management of 18% while applying the vehicle speed reduction limits the deviation to 0.2%. Experimental results show a good agreement with simulation data with 94% accuracy. We tested the protocol for urban and peripheral routes with maximum vehicle speed limits of 60 and 90 km/h.

Postpartum haemorrhage (PPH) is a significant cause of maternal morbidity and mortality worldwide, particularly in low-resource settings. This study aimed to develop a predictive model for PPH using early risk factors and rank their importance in terms of predictive ability. The dataset was obtained from an observational case-control study in Northern Rwanda. Various statistical models and machine learning techniques were evaluated, including logistic regression, logistic re-gression with elastic-net regularisation, Random Forest, Extremely Randomized Trees, and gradient boosted trees with XGBoost. Random Forest emerged as the best predictive model for PPH across three different train-test data partitions. The important predictors identified in the study were haemoglobin level during labour and maternal age. However, there were differences in PPH risk factor importance in different data partitions, highlighting the need for further investigation. These findings contribute to understanding PPH risk factors, highlight the importance of considering different data partitions and implementing cross-validation in predictive modelling, and emphasise the value of identifying the appropriate prediction model for the application. Effective PPH pre-diction models are essential for improving maternal health outcomes on a global scale. This study provides valuable insights for healthcare providers to develop predictive models for PPH to identify high-risk women and implement targeted interventions

Analyses of the three predominant types of sedimentation – clastic, carbonate and black shale – revealed their discontinuity/continuity in different facies environments of the Middle and Late Devonian of the central part of the Volga-Urals petroleum province, namely (1) in depressions, both condensed and non-condensed, (2) on the slopes of depressions and (3) in shallow water environments represented by tectonic arches or localised biohermal uplifts. The regional zonation of conodonts, correlated with the global chronostratigraphic scheme, substantiates the stratigraphic completeness of the general Devonian sequence in this area. In particular, the sedimentation of organic-rich black shales, traditionally considered as source rocks, lasted more than 29 million years, starting from the Late Eifel and ending at the Devonian-Carboniferous boundary. There was only one hiatus in the deposition of both black shales and carbonate sediments, lasting about 2.5 million years at the end of the Frasnian. That interval is dominated by clastic sediments, which are considered to be the most productive reservoirs of the Volga-Ural province. In the time interval from the beginning of the Eifel to the end of the Frasnian (about 17 Ma), (a) clastic sediments show the highest accumulation rates; (b) the most complete sequences occur in depressions; and (c) arches and uplifts show the most significant gaps in the geological record. During Famennian, (a) clastic sedimentation has completely ceased; (b) differences between the slopes of troughs and shallow-water environments have diminished, resulting in stable accumulation of carbonate sediments in both settings; (c) the decrease in sequence thickness (up to 50 m) in depressions suggests reduced accumulation rates of deep-water organic-rich black shales. The results help to understand the complex spatial relationship between different coexisting sedimentation types and focus attention to the incompleteness of the geological record in different environments.

Silicon Photomultipliers find applications across various fields. One potential Silicon Photomultiplier application domain is neutrino telescopes, where they may enhance the angular resolution. However, the elevated dark count rate associated with Silicon Photomultipliers represents a significant challenge to their widespread utilization. To address this issue, it is proposed to use Silicon Photomultipliers and Photomultiplier Tubes together. The Photomultiplier Tubes signals would serve as a trigger to mitigate the dark count rate, thereby preventing undue saturation of the available bandwidth. This paper presents an investigation into a fast and resource-efficient method for filtering Silicon Photomultiplier dark count rate. A low-resource and fast coincident filter has been developed, which removes the Silicon Photomultiplier dark count rate by using as trigger the Photomultiplier Tube input signals. The architecture of the coincidence filter, together with the first results obtained, which validate the effectiveness of this method are presented.

This is a retrospective chart review of outcomes of maxillofacial microvascular free flap reconstructions in pediatric and adolescent patients. A single head and neck surgical team performed all the included 136 procedures. Demographic and surgical patient data were recorded. Type of transfer performed in each recipient site and major complications were analyzed. Relevant influencing factors, such as age, gender and etiology of defect were determined using the ANOVA test and χ² test of independence. Results indicate a 90% success rate. No significant relation was found between the incidence of total flap loss and patient age, etiology or graft source. The maxillary reconstructions showed a higher incidence of total flap loss compared to mandibular ones (11 vs. 3 cases). Despite the high success rate, the findings underline the necessity for further research to validate these observations and enhance surgical methods for pediatric and adolescent patients.

An exposition is undertaken to reveal the significant impact of the time-dependent root parameter, on the stability of Pointwise Stationary Fluid Flow Approximation (PSFFA) model of the non-stationary queueing system. This opens new grounds to stability analysis of non-stationary queueing systems. Potential PSFFA applications of IoT are highlighted.

Large scale cropland erosion rates mapping and dynamic monitoring are critical for agricultural planning but extremely challenging. In this study, by using field investigation data collected from 20,155 land parcels in 2,781 sample units in the National Soil Erosion Survey, land use change data for two decades from the National Land Use/Cover Database of China (NLUD-C), we proposed a new point to surface approach to quantitatively assess long-term cropland erosion based on the CSLE model and non-homogeneous voting. The results show that cropland in Yunnan suffers from serious problem with unsustainable mean soil erosion rate of 40.47t/(ha·a) and erosion ratio of 70.11%, which are significantly higher than those of other land types. Engineering control measures (ECMS) have a profound impact on reducing soil erosion, soil erosion rate of cropland with and without ESMs differs by more than five times. Over the past two decades, the cropland area in Yunnan continues to decrease, with a net reduction of 7461.83 km2 and a ratio of −10.55%, which causes corresponding 0.32×108 t (12.12% ) decrease in cropland soil loss. We also quantified the impact of different LUCC scenarios on cropland erosion, and extraordinarily high variability was found in soil loss in different basins and periods. Conversion from cropland to forest contributes the most to cropland erosion reduction, while conversion from grassland to cropland contributes 56.18% of the increase in soil erosion. Considering the current speed of cropland regulation, it is the sharp reduction in land area that leads to cropland erosion reduction rather than treatments. The dilemma between the Grain for Green Policy and Cropland Protecting Strategy in mountainous areas should be treated carefully with shared understanding and collaborations from different roles.

This study aimed to simulate dynamic irrigation management zones (MZs) in two maize fields for a variable rate hose-reel fertigation machine (VRFM) with a 4-section boom control. Soil moisture content was measured from nine and four soil moisture sensors in Field 1 (8.2 ha) and Field 2 (2.5 ha), respectively in different dates during the 2022 crop season. Three- and five-MZs scenarios were simulated per irrigation and the theoretical maps were processed for implementation. The application maps fitted to the VRFM showed significant spatiotemporal variations in irrigation requirements. For instance, in Field 1, 3-MZs modelling showed that the areas requiring High (H), Medium (M), and Low (L) level irrigation on July 21 were 1.60, 4.84, and 1.85 ha, respectively, whereas the farmer applied uniform rate over the whole field. H level sub-areas ranged between 1.22 ha (July 25) and 3.25 ha (July 7), showing a coefficient of variation (CV) of 43.32% for the 3-MZs, whereas H level sub-areas for 5-MZs varied from 0.41 ha (July 2) to 1.49 ha (July 7) with a CV value of 48.84%. High levels of within-field variability can be addressed using precise and dynamic irrigation MZs fitted to the irrigation technology used.

This study investigates the suitability of the timestamp approach algorithm for predicting blood pressure (BP) using wearable and comfortable devices, showcasing its accuracy even with low-frequency sampled signals. Developed within the SINTEC European project, the algorithm utilizes Electrocardiogram (ECG) and Photoplethysmogram (PPG) sensors, demonstrating promising results in both laboratory and hospital settings. The research emphasizes the algorithm’s potential to transform continuous and non-invasive BP monitoring through wearable technology, offering frequent measurements with minimal discomfort. While the study shows promise, further exploration is needed, focusing on optimizing machine learning coefficients for long-term monitoring applications and addressing potential changes over time. Technological improvements, including the implementation of edge computing algorithms, hold the key to enhancing BP accuracy, denoising techniques, and integrating alarm systems for future wearable solutions. This study emphasizes the adaptability of the algorithm for diverse healthcare environments, paving the way for broader applications in convenient and reliable BP monitoring.

Chum salmon (Oncorhynchus keta) exhibit a remarkable ability to adapt to changes in salinity during their life cycle. However, the fertilized egg stages are sensitive to salinity, affecting on-togeny and hatching. This study investigated the effect of salinity (0, 1, 3, and 5 psu) on the sur-vival of two developmental stages (< 1 day after fertilization and < 1 day after the eyed-egg stage) of fertilized eggs. Based on the experimental results, we assessed the spawning ground environ-ment of the Namdae River, where the largest number of salmon in Korea migrate to spawn. Sur-vival of the < 1 day old fertilized eggs decreased sharply at 3 psu or more, and all eggs died at 5 psu. Hatching rates of the eyed-egg stage varied depending on salinity, but hatching occurred under all environmental conditions. After 2010, the salinity of the layer of water in contact with the sediment in the lower reaches of the river tended to increase (> 6.9 psu) with the frequency of high waves. Overall, the function of the lower river in spawning and hatching is weakening. This study enhances our understanding of the effects of climate change, including increased wave ac-tivity, on salmon spawning grounds

Background There is a considerable overlap between clinical presentation of post-COVID-19 condition (PCC) and myalgic encephalomyelitis/chronic fatigue syndrome (ME/CFS) . Many of their common symptoms can be linked to dysregulation of the autonomic nervous system (dysautonomia). This study aimed to objectively assess autonomic function in patients with PCC and in patients with ME/CFS whose disease was not related to COVID-19. Methods Synchronous recordings of an electrocardiogram, continuous dynamics of blood pressure in the digital artery using the Penaz method and ultrasound pneumotachography with the spirography function were obtained with spiroarteriocardiorhythmography method in 34 patients diagnosed with ME/CFS, in whom the onset of the disease was not associated with COVID-19, 29 patients meeting PCC definition and 32 healthy controls. Heart rate variability (HRV), systolic and diastolic blood pressure variability (RV), respiration variability were assessed at rest and in tests with fixed respiratory rates. At rest, indicators of baroreflex regulation were additionally determined (baroreflex effectiveness index and baroreflex sensitivity). Results The total power, power of very low frequency, low-frequency and high-frequency of RR interval variability at rest as well as baroreflex effectiveness index in up-ramps of arterial blood pressure and baroreflex sensitivity were significantly lower both in PCC and ME/CFS patients compared to HC. Several diagnostic prediction models for ME/CFS were developed based on HRV parameters. During slow breathing HRV parameters return to normal in PCC, but not in ME/CFS. Correlation analysis revealed a close relationship of HRV, RV parameters and baroreflex sensitivity with fatigue, but not with HADS depressive/anxiety symptoms in ME/CFS and PCC. Conclusion A similar pattern of HRV and baroreflex failure with signs of a pathological acceleration of age-dependant dysautonomia was identified in ME/CFS and PCC. The clinical, diagnostic and therapeutic implications of these findings are discussed, in light of previously described relationship between inflammation, vascular pathology, atherosclerotic cardiovascular disease and autonomic dysfunction.

Milling machines have made denture fabrication possible with high accuracy in a short time. However, the relationship between the milling conditions, accuracy, and milling duration has not been clarified. This study aimed to clarify the effects of milling conditions on surface roughness and milling duration. The specimen was designed using a CAD software, and milled using PMMA disks. In milling, the parameters of finishing the specimen surface were adjusted. Three different spindle speeds and four different feed rates were set. Twelve combinations of each parameter were used for milling, and the surface roughness and milling duration were measured. Results showed that the surface roughness significantly increased with the feed rate on the slopes of the specimen. The surface roughness differed with the spindle speed on the left and right slopes. The spindle speed and feed rate did not affect the surface roughness on the flat surface. The milling duration was not affected by spindle speed but decreased as the feed rate increased. In conclusion, by increasing both the spindle speed and feed rate, the milling duration could be shortened while maintaining a constant surface quality. The optimum milling conditions were a spindle speed of 40,000 rpm and feed rate of 3,500 mm/min.

Whole blood viscosity, a hemorheological factor, is currently used for diagnosis, as it is correlated with various vascular diseases that are difficult to diagnose early with a general blood test. It was determined that it was necessary to set reference intervals for further studies and utilization of whole blood viscosity in cats, a representative companion animal, and this study was conducted. 50 healthy cats were recruited for the study and whole blood viscosity, complete blood count, and serum chemistry tests were performed. The reference intervals of whole blood viscosity were 15.169 to 43.684 cP at a shear rate of 1 s-1 reflecting diastole, and 3.524 to 5.544 cP at a shear rate of 300 s-1 reflecting systole. Red blood cells, hematocrit, hemoglobin, white blood cells, and neutrophils in the complete blood count, and total protein, albumin, globulin, and cholesterol in the serum chemistry were significantly correlated with whole blood viscosity. The results of this study set reference intervals of whole blood viscosity for healthy cats in a wide shear rate range that has not yet been fully established and investigated its correlation with other blood indicators.

The Covid-19 crisis has been one of the most relevant economic shocks in the history of the modern economy, mainly due to the restrictions on travel and social interaction taken by the authorities (quarantines, closure of schools, artistic activities, bars, and restaurants, capacity in stores), to reduce the transmission of the virus (Sars-Cov2), having consequences on the national productions of all countries (about 7% for the loss of GDP worldwide). In our study, we analyze, through clustering methods, the effects of the level of contagion, economic projections, and economic mitigation measures taken by governments for managing the pandemic. According to the analyses, it can be concluded that a low infection rate implies a lower loss of product and economic savings when applying economic mitigation measures, taking relevance in the management of sanitary measures to reduce the transmission of the virus (and the temporality of these).

This paper presents a comprehensive study based on multiphase seepage and wellbore multiphase flow theories. It establishes a gas intrusion rate calculation model that considers various factors including formation pore permeability, bottomhole pressure difference, drilling fluid rheology, and surface tension. Experiments were conducted to investigate the gas intrusion mechanism under shut-in conditions, and the experimental results were employed to validate the reliability of the proposed gas intrusion rate calculation method. Furthermore, the research explores the transportation rates of single bubbles and bubble clusters in drilling fluid under shut-in conditions. Meanwhile, empirical expressions were derived for the drag coefficient for single bubbles and bubble clusters in the wellbore. These expressions can be used to calculate gas transportation rates for various equivalent radii of single bubbles and bubble clusters. Additionally, a method was developed for calculating the rising velocity of bubble clusters in water based on experimental results. The study reveals that the average bubble size in the bubble cluster is significantly smaller than the size of the single bubble generated from the orifice. When the viscosity of the drilling fluid is low, the bubble cluster transportation velocity exhibits a positive correlation with the average bubble diameter. When the average bubble diameter exceeds 1 mm, the bubble velocity no longer varies with the change in the bubble cluster diameter. The initial bubble size of intrusive gas, the transportation speed of intrusive gas in the wellbore, the gas intrusion rate, and variations of the wellbore pressure after gas intrusion were analyzed. The research results provide theoretical support for wellbore pressure prediction and pressure control under shutdown conditions.

Gabapentin (GBP), a GABA analogue, is primarily used as an anticonvulsant to treat partial seizures and neuropathic pain. While a majority of the side effects are associated with the nervous system, emerging evidence suggests a high risk for heart diseases in the patients taking GBP. In the present study, we used a preclinical model of rats to investigate (1) the acute cardiovascular responses to GBP (bolus i.v. injection, 50 mg/kg) and (2) the effects of chronic GBP treatment (i.p. 100 mg/kg/day x 7 days) on cardiovascular function and the myocardial proteome. Under isoflurane-anesthesia, rat blood pressure (BP), heart rate (HR), and left ventricular (LV) hemodynamics were measured using Millar pressure transducers. The LV myocardium and brain cortex were analyzed by proteomics, bioinformatics, and western blot to explore the molecular mechanisms underlying GBP-induced cardiac dysfunction. In experiment (1), we found that i.v. GBP significantly decreased BP, HR, maximal LV pressure, and maximal and minimal dP/dt, whereas it increased IRP-AdP/dt, Tau, systolic, diastolic, and cycle durations (*p < 0.05 and **p < 0.01 vs baseline; n = 4/group). In experiment (2), we found that chronic GBP treatment resulted in hypotension, bradycardia, and LV systolic dysfunction, with no change in plasma norepinephrine. In the myocardium, we identified 109 differentially expressed proteins involved in calcium pathways, cholesterol metabolism, and galactose metabolism. Particularly, we found that calmodulin, a key protein of intracellular calcium signaling, was significantly upregulated by GBP in the heart but not in the brain. In summary, we found that acute and chronic GBP treatments suppressed cardiovascular function in rats, which is attributed to abnormal calcium signaling in cardiomyocytes. These data reveal a novel side effect of GBP independent of the nervous system, providing important translational evidence to suggest that GBP can evoke adverse cardiovascular events by depression of myocardial function.

Having as objective to reach a circular economy, it is important to maximize the Physical Asset’s Life Cycle. The evaluation of Physical Assets Life Cycle may have several approaches which may provide different results. These differences may not be very significant, but must be taken into consideration, because they have consequences in the manager decision. This permits to have a wider time interval to decide when to withdrawal the Physical Asset or to renewal it, and or if this ought to continue functioning because the profits are higher than the expenses, what allows to diminish waste and increase sustainability. These are some aspects that are discussed in this paper, which presents several models to evaluate the Physical Assets Life Cycle, considering the market value, devaluations methods and a more generalized way of Fisher’s Equation, which can include the Risk tax, among others. The results are discussed supported in data for simulation, which are used for each Econometric Model aiming to evaluate the differences among them. In all Models they are considered not only the expenses, namely of Investment and Functioning, but also the Profits, which permit to evaluate the Physical Asset Life Cycle in a holistic way. The models are very versatile, allowing to evaluate quantitatively the changing in the maintenance policies, the energy prices variations, the risk evaluation, the variation of profits according to the real market, and so on. The results demonstrated the robustness of the approach described and that maximize the Physical Assets Life Cycle allowing to minimize the consumption of world resources and, by consequence, it contributes for a more sustainable world.

Background: Depending on the phase of the menstrual cycle the athlete is in, some kinetic, physiological and fatigue variables will show differences. The aim of this study is to analyze whether there are changes in these variables over the course of the menstrual cycle. Methods: Eight regular female runners and triathletes performed a maximal treadmill test, as well as a submaximal test (6’ stages at 50%, 60% and 80% of maximal aerobic speed) in each of the phases of the menstrual cycle: bleeding phase (day 2.4 ± 0.7), follicular phase (day 10.4 ± 2.2) and luteal phase (day 21.8 ± 2.1). Running dynamics were measured (using RunScribe) at the end of each test, as were lactate concentration, heart rate and fatigue (evaluated on a scale of 0 to 5). Results: Higher shock (G) values were recorded in the bleeding phase and higher vertical spring stiffness (kN/m) in the follicular phase. The phase of the menstrual cycle had a significant effect on average and peak heart rate, which was significantly higher in the follicular phase. Conclusions: Higher vertical spring stiffness was observed in the follicular phase, as well as higher peak and average heart rate.

For a subject suffering from complex post-traumatic stress disorder, a psychological intervention program was designed, monitored in real-time during psychotherapy, and evaluated quantitatively and qualitatively after psychotherapy. One male subject participated in this program under consent. The proposed intervention program was designed using cognitive behavioral therapy and stabilization treatments for body-based sensory processes in four sessions of 90 min each. During psychotherapy, a wearable heart sensor and a communication application were utilized to determine the subject’s current psychological state. After the intervention, the effect of the proposed program was analyzed qualitatively and quantitatively using the Impact of Event Scale–Revised (IES-R-K), Athens insomnia scale (AIS), and heart rate variability (HRV). After the intervention program was conducted, the subject reconstructed his traumatic events and trained himself with certain psychological techniques to decrease his negative thoughts and emotions induced by his previous traumatic events. The IES-R-K and AIS ten months after the last session were changed positively by approximately 25% compared with the subject’s state before the first session. During psychotherapy, the HRV exhibited a significant correlation with the subject’s emotional state. The proposed intervention program induced a positive change in the subject. Although the HRV was well utilized in this investigation, more sophisticated statistical analysis will be required for clinical trials.

Marine sediment sample was collected and the total aerobic population was counted and probiotic Bacillus cereus was isolated. Then it was mixed with formulated feed by spraying, while control diet was purchased from a local aquarium. 30 days of feeding experiment was conducted. Carassius auratus fishes were randomly divided into two experimental groups in rectangular tanks. The first group served as a control in which fishes were fed with commercial feed. The second group of fish were fed with probiotic incorporated feed. After 40 days, their survival and growth performance were detected. Bacillus cereus incorporated feed significantly yielded higher survival rate of the fish compared to control. Food conversion ratio (FCR) was significantly lower than the control group. The main aim of this work is to investigate the effect of a marine probiotic bacteria, Bacillus cereus on the survival and growth performance of gold fish Carassius auratus.

This work deals with finding out whether the heart rate values of operators of forwarding machines during the work shift are influenced by the individual activities that the operator has to perform during timber skidding, or by the operators themselves. Furthermore, the work deals with determining the difficulty of individual activities in terms of physical load. For this purpose, the work shift of operators carrying out timber skidding was divided into individual activities: Driving, Maintenance, Forwarding, Break. During these work activities, the heart rate of each operator was taken for subsequent evaluation. The results show that the highest pulse rates of the operators were achieved during the Maintenance of the entrusted machine, while the highest pulse fluctuations in the operators were recorded during Forwarding. As part of this activity, the highest heart rate of the entire measurement process was recorded (132.0000 bpm), but also the lowest (42.0000 bpm). Furthermore, it was proven that both the operator and the activity he performs affect the pulse rate. The activities themselves did not differ from each other in only one of the six cases of comparison. Specifically, it was Driving and Forwarding.

Indirect calorimetry (IC) is a widely used method to study animal energy metabolism by measuring gas exchange. The accuracy of IC depends on detecting variations in signals reflecting the metabolic response, which can be challenging due to measurement noise and external factors. In this study, we propose a methodology to validate IC systems, including an easy-to-use spreadsheet for data computing, to verify accuracy and detect whole-system leaks. We conducted a re-covery test using a simulation of CO2 dynamics in MS Excel and injecting a known CO2 concentration into four respirometry chambers. The clearance rate of CO2 was observed and compared to the expected clearance rate from the simulation. The results from the recovery test in our system show that the proposed methodology is accurate and precise. The proposed methodology and recovery test can be used to standardize the validation of IC systems, providing accurate measurements of animal energy metabolism in different environmental conditions and energy utilization from feeds.

Natural gas hydrate has gained significant attention in recent years. To safely and sustainably exploit the natural gas from gas hydrate-bearing sediments, it is crucial to understand the long-term mechanical characteristics of the hydrate reservoir. In this study, the influence of hydrate and fine particles on the strain rate dependence of hydrate-bearing sediments under plane strain conditions has been studied. The experimental results show that the strain rate dependency of the mechanical properties of hydrate-bearing sediments is positively correlated with hydrate saturation instead of the morphology of hydrate in sediments. The residual strength of hydrate-bearing sediments is primarily controlled by the hydrate saturation and is independent of the strain rate. Changes in hydrate saturation, and fines content, can affect the relationship between the strain rate and shear band angle. Finally, the local volumetric expansion effect of hydrate-bearing sediments without fines content is more significant and shows a strong strain rate dependence characteristic. Overall, this study provides valuable insights into the long-term mechanical characteristics of hydrate reservoirs. These insights can contribute to the development of a constitutive model of hydrate-bearing sediments with time-dependence in the future, and which is meaningful to the exploitation of natural gas hydrate.

The circadian and stress-realizing systems are interconnected, and the balance of their interaction determines the state of human health. The objective of this study was to investigate the modulating effect of activating the circadian system on heart rate variability in female medical students with high anxiety while performing a cognitive task. After 20 minutes of adequate stimulation of circadian photoreceptors with a monochromatic blue light, the cognitive task performance resulted in a decrease in sympathetic impact. During the session of using Blue Sky Pro glasses, a trend of increasing heart rate variability was observed in a state of relative rest (especially in the first 5 minutes). A comparative analysis of the parameters of the letter cancellation test before and after light exposure revealed a statistically significant increase in the indexes reflecting mental productivity, work accuracy, and concentration of attention. The results suggest an essential physiological role of the human circadian system in modulating the autonomic and psycho-emotional conditions, as well as cognitive functions of individuals with high anxiety. Our findings indicate the possibility of quickly correcting the balance in human systemic regulatory mechanisms using the activation of retinal circadian photoreceptors by blue light.

Several studies have reported a relationship between autonomic dysfunction　 during tasks and Internet addiction. Changes within 24 h regarding heart rate variability (HRV) may be a more sensitive indicator than short term observations. We evaluated the influence of excessive Internet usage on HRV using a 24 h electrocardiogram (ECG) and examined acute changes during computer game tasks. A total 13 high school students and 22 young adults were recruited, and divided into excessive Internet user and non- excessive user groups based on Internet addiction test scores. The ECG was recorded continuously for 24 h by a wearable sensor and during two computer games (the Iowa gambling task and each participant’s preferred game) using a standard type ECG system. Multiple psychometric tests were also conducted. The excessive Internet user group exhibited clinically significant depressive symptoms, and higher self-reported scores for anxiety, impulsivity, autistic tendencies, and sleep problems than the non- excessive internet user group. There were weak differences within the 24 h high-frequency (HF) band power between two groups. During the Iowa gambling task, younger participants exhibited a reduced HF response, which may be related to weaker top- down self- regulatory mechanisms.

This case report examined the characteristics of body composition, sleep quality, and autonomic nerve activity in active older adults with a younger body age—calculated from age trends in body composition and basal metabolic rate. We selected two cases who had a metabolic age younger than their actual age. They had good sleep quality, low sleep quality scores, no sarco-penia, strong muscle and grip strength, and balanced autonomic nervous system activity. Fur-thermore, they were determined to be much younger than their actual age. They were compared with two other age- and sex-matched cases, who had poor sleep quality, unbalanced autonomic nervous system activity, and had a physical age closer to their actual age. Older adults with more muscle mass and higher basal metabolism were younger than their actual age, had a better sleep status, and a good balance of autonomic nervous activity in the exercise stimulation. They also had lower percentages of body- and visceral fat and higher body water. Meanwhile, the older adults with standard muscle mass and basal metabolic rate had a poor sleep status and no sympathetic hyperactivity in the exercise simulation.

This study aimed to verify the effects of an acute increase in blood pressure (BP) and/or renal sympathetic nerve activity (rSNA) on the renal excretion of sodium and water and its potential effect on the regulation of NHE3 activity. Uninephectomized anesthetized male Wistar rats were divided into three experimental groups: 1) Sham, the rats had their BP and rSNA recorded, and urine was collected for 2 h; 2) bicuculline (Bic) paraventricular nucleus of the hypothalamus (PVN), rat BP, and rSNA were recorded, and urine was collected for 1 h at baseline conditions and 1 h after bicuculline injection into the PVN; 3) RNS + Bicuculine injection into the PVN, BP, and rSNA were recorded, and urine was collected 1h after RNS and 1 h after bicuculline injection into the PVN. Renal nerve stimulation (RNS) decreased sodium and water excretion independent of changes in BP. However, after Bic in the PVN during RNS stimulation, BP and rSNA increased up to 30% and 60%, respectively, increasing diuresis (5-fold) and natriuresis (2.3-fold), accompanied by a significant reduction in the NHE3 activity independent of GFR changes. In conclusion, an acute increase in BP overcomes such effects, generating diuresis, natriuresis, and NHE3 activity inhibition.

Background: Heart rate variability is a non-invasive, measurable, and established autonomic nervous system test. Long-term COVID-19 sequelae are unclear; however, acute symptoms have been studied. Objectives: To determine autonomic cardiac differences between long COVID-19 patients and heathy controls and evaluate associations among symptoms, comorbidities, and laboratory findings. Methods: This single-center study included long COVID-19 patients and healthy controls. The heart rate variability (HRV), a quantitative marker of autonomic activity, was monitored for 24 h using an ambulatory electrocardiogram system. HRV indices were compared between case and control groups. Symptom frequency and inflammatory markers were evaluated. The significance level of 5% (p-value 0.05) was adopted. Results: A total of 47 long COVID-19 patients were compared to 42 healthy controls. Patients averaged 43.8 (SD14.8) years old, and 60.3% were female. In total, 52.5% of patients had moderate illness. Post-exercise dyspnea was most common (71.6%), and 53.2% lacked comorbidities. COVID-19 patients had 4 times more dyslipidemia. CNP, D-dimer, and CRP levels were elevated (p-values of 0.0098, 0.0023, and 0.0015, respectively). The control group had greater SDNN24 and SDANNI (OR = 0.98 (0.97 to 0.99; p = 0.01)). Increased low-frequency (LF) indices in COVID-19 patients (OR = 1.002 (1.0001 to 1.004; p = 0.030)) and high-frequency (HF) indices in the control group (OR = 0.987 (0.98 to 0.995; p = 0.001)) were also associated. Conclusions: Patients with long COVID-19 had lower HF values than healthy individuals. These variations are associated with increased parasympathetic activity, which may be related to long COVID-19 symptoms and inflammatory laboratory findings.

In Los Angeles, at one point, the Covid-19 testing positivity rate was 6.25%, or one in sixteen. This translates to, on average, one in sixteen specimens testing positive and the vast majority testing negative. Usually, we run sixteen tests on sixteen specimens to identify the positive one(s). This process can be time consuming and expensive. Since a group of negative specimens pooled together for testing will produce a negative result, one single test could potentially eliminate many specimens. Only when the pooled specimen tests positive do we need further testing to identify the positive one(s). Based on this concept, we designed a strategy that will identify the positive specimen(s) efficiently. Assuming one in sixteen specimens is positive, we find that only four tests are needed. Furthermore, we can run them simultaneously, saving both resources and time. Although, in the real world, we cannot make the assumption of only one positive specimen, the same strategy works with slight modification and proves to be much more efficient than the conventional testing. Our strategy returns an answer 48% of the time in four tests and one time cycle. Overall, the average number of tests is seven or eight depending on the follow-up testing, and the average time cycle is about one and a half.

The lateral pressure generated by liquefied soil on pile is a critical parameter in the analysis of soil-pile interaction in liquefaction-susceptible sites. Previous studies have shown that liquefied sand behaves like a non-Newton fluid, and its effect on piles has rate-dependent properties. In this study, a simplified pseudo-static method for liquefiable soil-pile interaction analysis is proposed by treating the liquefied soil as a thixotropic fluid, which considers the rate-dependent behavior. The viscous shear force generated by the relative movement between the viscous fluid (whose viscosity coefficient varies with excess pore pressure and shear strain rate) and the pile was assumed to be the lateral load on the pile. The results from the simplified analysis show that the distribution of bending moment is in good agreement with experiments data. Besides, the effects of various parameters, including relative density, thickness ratio of non-liquefiable layer to liquefiable layer, and frequency of input ground motion, on the pile-soil rate-dependent interaction were discussed in detail.

Driver drowsiness is one of the leading causes of traffic accidents. This paper proposes a new method for classifying driver drowsiness using deep convolution neural networks trained by wavelet scalogram images of electrocardiogram (ECG) signals. Three different classes were de-fined for drowsiness based on video observation of driving tests performed in a simulator for manual and automated modes. The Bayesian optimization method is employed to optimize the hyperparameters of the designed neural networks, such as the learning rate and the number of neurons in every layer. To assess the results of the deep network method, Heart Rate Variability (HRV) data is derived from the ECG signals, some features are extracted from this data, and finally, random forest and k-nearest neighbors (KNN) classifiers are used as two traditional methods to classify the drowsiness levels. Results show that the trained deep network achieves balanced accuracies of about 77% and 79% in the manual and automated modes, respectively. However, the best obtained balanced accuracies using traditional methods are about 62% and 64%. We conclude that designed deep networks working with wavelet scalogram images of ECG signals significantly outperform KNN and random forest classifiers which are trained on HRV-based features.

Variable nitrogen(N) rate fertilization based on remote sensing is challenging for cotton production fields, but active crop canopy sensors (ACS) appear as an alternative to make this practical on farm since they can be used at night as well. The crop spatial variability in inherent in crop production in general, and not on-the-go solutions can be used with this type of active sensing technologies. Thus, the purpose of this study was to investigate the potential of two vegetation indices to identify the N requirement variability for cotton plants and to develop prototype algorithms for topdressing nitrogen variable rate on commercial and experimental areas, using the N-sufficiency methodology based on virtual reference. The concept of virtual reference is to use a histogram to characterize the vegetation index of properly fertilized plants without establishing an N-rich plot as a reference strip. The experiment was conducted in strips with four different N rates (0, 45, 90 and 180 kgN ha^-1) during the 2015, 2016, 2017 and 2018 crop seasons in partnership with large cotton producers in Mato Grosso and also in experimental area of Embrapa Agrosilvopastoral. Two algorithms for variable rate nitrogen fertilization for cotton were developed, namely: 1) N recommendation algorithm for cotton in commercial production system: N rate (kg.N ha^-1) = -234.79 ISN² + 49,879 ISN + 195.15; R² = 0.97; and 2) for cotton grown in experimental area: N dose (kgN ha^-1) = -174.73 ISN² - 107.21 ISN + 306.78; R² = 0.94.

Aedes (Stegomyia) albopictus is a mosquito native to Southeast Asia. Currently, it has a wide distribution in America where natural infection with arboviruses of medical and veterinary importance has been reported. In spite of their importance in the transmission of endemic arbovirus, basic information of parameters affecting their vectorial capacity is poorly investigated. The aim of the work was to update the distribution range of Ae. albopictus in the Americas, review the blood-feeding patterns and compare the minimum infection rate (MIR) of the dengue virus (DENV) between studies of vertical and horizontal transmission. The current distribution of Ae. albopictus encompasses 21 countries in the Americas. Extensive review has been conducted for the blood-feeding patterns of Ae. albopictus. The results suggest that the mosquito is capable of feeding on 16 species of mammals and five species of avian. Humans, dogs, and rats are the most common host. Eight arboviruses with the potential to infect humans and animals have been isolated in Ae. albopictus. In the United States of America (USA), Eastern equine encephalitis virus, Keystone virus, La Crosse Virus, West Nile virus, and Cache Valley virus were isolated in the Asian mosquito. In Brazil, Mexico, Colombia, and Costa Rica, DENV (all serotypes) has been frequently identified in field-caught Ae. albopictus. Overall, the estimated MIR in Ae. albopictus infected with DENV is similar between horizontal (10.95) and vertical transmission (8.28). However, in vertical transmission, there is a difference in the MIR values if the DENV is identified from larvae or adults (males and females emerged from a collection of eggs or larvae). MIR estimated from larvae is 14.04 and in adults is 4.04. In conclusion, it has to be highlighted that Ae. albopictus is an invasive mosquito with wide phenotypic plasticity to adapt to broad and new areas, it is highly efficient to transmit the DENV horizontally and vertically, it can participate in the inter-endemic transmission of the dengue disease, and it can spread zoonotic arboviruses across forest and urban settings.

The aim of the work was to update the distribution range of Aedes (Stegomyia) albopictus Skuse in the Americas, review the blood-feeding patterns and compare the minimum infection rate (MIR) of the dengue virus (DENV) between studies of vertical and horizontal transmission. The current dis-tribution of Ae. albopictus encompasses 21 countries in the Americas. Extensive review has been conducted for the blood-feeding patterns of Ae. albopictus. The results suggest that the mosquito is capable of feeding on 16 species of mammals and five species of avian. Humans, dogs, and rats are the most common host. Eight arboviruses with the potential to infect humans and animals have been isolated in Ae. albopictus. In the United States of America (USA), Eastern equine encephalitis virus, Keystone virus, La Crosse Virus, West Nile virus, and Cache Valley virus were isolated in the Asian mosquito. In Brazil, Mexico, Colombia, and Costa Rica, DENV (all serotypes) has been frequently identified in field-caught Ae. albopictus. Overall, the estimated MIR in Ae. albopictus infected with DENV is similar between horizontal (10.95) and vertical transmission (8.28). However, in vertical transmission, there is a difference in the MIR values if the DENV is identified from larvae or adults (males and females emerged from a collection of eggs or larvae). MIR es-timated from larvae is 14.04 and in adults is 4.04. In conclusion, it has to be highlighted that Ae. albopictus is an invasive mosquito with wide phenotypic plasticity to adapt to broad and new areas, it is highly efficient to transmit the DENV horizontally and vertically, it can participate in the inter-endemic transmission of the dengue disease, and it can spread zoonotic arboviruses across forest and urban settings.

Rural electrification rate (RER) in Africa is still low to date. Several countries in Sub-Saharan Africa have tried to address this problem using conventional single-phase two-wire or three-phase three-wire systems, however at large costs due to the nature of dispersed rural load centers, low load demand, and low population density. Another solution of off-grid generation creates associated health problems. Therefore, this paper undertakes a review of a single wire earth return (SWER) network as a RER improvement solution. The paper undertakes intensive literature review to elucidate challenges and solutions to the implementation of SWER technology. Advantages of SWER technology discussed make it the choice for RER improvement in Sub-Saharan African countries. After that, a case study is selected in rural Tanzania, and a preliminary SWER network design is undertaken.

During the COVID-19 lockdown in Wuhan, transportation, industrial production and other human activities declined significantly, as did the NO2 concentration. In order to assess the relative contributions of different factors to reductions of air pollutants, sensitivity experiments were implemented by random forest (RF) model, with the comparison of contributions of meteorology, road traffic, and emission sources between different periods. Besides, an emulator was operated to suggest an appropriate limit for control of transportation. The RF models showed different mechanisms for air pollutants. Within-city Migration index (WMI) was more important in the normal, pre-lockdown and post-pandemic model while Out-Migration Index (OMI) was emphasized in the lockdown model. In the COVID-19 lockdown period, 73.3% of the reduction can be attributed to the decreased road traffic, showing massive impact of road traffic on the air quality. In the post-pandemic period, meteorology controlled about 42.2% of the decrease and emissions from industry and household controlled 40.0% while road traffic only contributed to 17.8%. It was suggested that priority of restriction should be given to road traffic within the city. A limit of less than 40% on the control of the road traffic can get a better effect, especially for cities with severe traffic pollution.

Alcoholism is attributed to regular or excessive drinking of alcohol and leads to the disturbance of the neuronal system in the human brain. This results in certain malfunctioning of neurons that can be detected by an electroencephalogram (EEG) using several electrodes on a human skull at appropriate positions. It is of great interest to be able to classify an EEG activity as that of a normal person or an alcoholic person using data from the minimum possible electrodes (or channels). Due to the complex nature of EEG signals, accurate classification of alcoholism using only a small data is a challenging task. Artificial neural networks, specifically convolutional neural networks (CNN), provide efficient and accurate results in various pattern-based classification problems. In this work, we apply CNN on raw EEG data, and demonstrate how we achieved 98% average accuracy by optimizing a baseline CNN model and outperforming its results in a range of performance evaluation metrics on the UCI-KDD EGG dataset. This article explains the step-wise improvement of the baseline model using the dropout, batch normalization, and kernel regularization techniques, and provides a comparison of the two models that can be beneficial for aspiring practitioners who aim to develop similar classification models in CNN. A performance comparison is also provided with other approaches using the same dataset.

Background: Since the previous study dealing with the case fatality ratio and infection fatality ratio caused by COVID-19, the author has received many comments that prompted the question: "Why did an optimistic prognosis fail?" To answer this question, a more detailed and expanded analysis was carried out in a new study. Objective: To evaluate the dynamics of monthly numbers of cases, deaths, tests and CFR worldwide during three phases of the COVID-19 pandemic. Material and Methods: Twenty three sets of databases, dated the 22nd of each month from January 2020 to November 2021, for 213 countries were collected from the Worldometer website. The number of cases, deaths, tests, CFR, IFR, etc. were counted for various periods of time for each of the 213 countries, then results related to different periods of time were compared. Results: The analysis of the main epidemiological parameters led to the division of three phases of the global pandemic evolution. The first phase (23.01.20-22.07.20), the second phase (23.07.20-22.01.21) and the third phase (23.01.21-22.07.21) were different in terms of the number of tests performed, new cases, and mortality due to COVID-19. By the end of the second phase, the worldwide statistics indicated the imminent end of the pandemic, but the third phase was characterized by a sudden rise in the number of new cases and deaths that could not be explained rationally. The most dramatic evolution of the epidemic curve occurred in the countries where doctors had successfully battled COVID-19 during the first two phases of the pandemic. Conclusions: Despite the decrease in overall death numbers during the latest months analyzed, additional study is necessary to identify the cause for the increase in the number of new cases and deaths during the third phase of the pandemic. Only complete information regarding the positive and negative impact of medical and non-medical methods of diagnostics and prophylaxis of COVID-19 can help to organize effective measures to end the current pandemic and prevent a similar one from occurring in the future. Presumably, there are several causes of the negative evolution of the current pandemic, including the overreliance on PCR tests, application of non-specialized premises for quarantine and treatment, decrease in herd and individual immunity, inadequate change of therapeutic protocols, and ignoring prophylactic treatment. It can be suggested that the use of immunemodulatory drugs, for example, thymus extract or thymic peptides, in groups of people with compromised immunity is necessary, and prophylactic and therapeutic protocols should be changed from the 'standard' types to 'personalized' ones.

The closed forms of the non-resonant thermonuclear function in the Maxwell-Boltzmann and Tsallis case with depleted tail are obtained in generalized special functions. The results are written in terms of H-function of two variables. The importance of the results in this paper lies in the fact that the reaction rate probability integrals in Maxwell-Boltzmann and Tsallis cases are not obtained by the conventional method of approximation or by means of a single variable transform technique but by means of a two variable transform method. The Behaviour of the depleted non-resonant thermonuclear functions are examined using graphs. The results in the paper are of much interest to astrophysicists and statisticians in their further work in this area.

Previous studies investigated the effects of seed rates and seed recycling practices on the yield and yield related variables. However, higher yield does not always guarantee cost-efficiency. This study aimed at investigating the yield effects of plot-level seed rate along with the cost-benefit analysis of seed recycling practices. This study has introduced the dose-response model to the existing analytical methods used in analyzing the effect of different agrochemicals on crop yield. A multi-stage stratified sampling technique was used to select a total of 450 sample respondents. Data was gathered using a mix of data collection tools. Descriptive statistics along with the dose-response model have been applied for data analysis. Farmers of the study were found to be dissimilar in terms of their seed rate application. The dose-response analysis indicated that the highest average wheat yield has been associated with a seed rate of 50 kg ha-1 above what is recommended. The yield effect of seed recycling has also been assessed and a one-time seed recycling has caused a yield decline of 665 kg ha-1 as compared to the non-recycled seeds. The cost reduced by using recycled seed is by far lower than the economic gains associated with using unrecycled and fresh seeds. The cost-benefit analysis made clear that farmers can reduce their seed costs through seed recycling but their yields and net income can be best improved by using unrecycled CBWS. Thus, farmers must be encouraged to make use of unrecycled seed by establishing agricultural credit schemes geared towards seed procurement and seed price subsidy as key strategies to reduce economically wasteful seed recycling practices.

This work assesses sea-level rise using three different models created on Free and Open-Source Software for Geographic Information System (FOSS4GIS). Based on regional projections of Special Report on Climate Change and Oceans and Cryosphere (SROCC) of the Intergovernmental Panel on Climate Change (IPCC), the models were applied to a case of study on Rio Grande do Sul coast – Brazil under different sea-level rise scenarios by the end of this century. The End Point Rate for QGIS (EPR4Q), calculates a shoreline projection using End Point Rate method. The Uncertainty Bathtub Model (uBTM), analyses the sea-level rise impact by the uncertainty of sea-level projec-tions and vertical error of the Digital Elevation/Terrain Model (DEM/DTM). The Bruun Rule for Google Earth Engine Model (BRGM) predicts the shoreline position with sea-level rise, using topographic and bathymetric data from Unmanned Aerial Vehicles (UAV) and Coastal Modelling System (SMC – Brazil), respectively. The results indicated a maximum shoreline retreat for 2100 of -502 m and -1727 m using EPR4Q and BRGM, correspondingly. The uBTM using the land-use of Mapbiomas showed a maximum of 44.57 km2 of urban area impacted by the sea-level flood. This research highlights the possibility of performing coastal management analysis in GIS environ-ment using non-commercial software.

Wenchuan earthquake that occurred in China in 2008 caused severe damage to a large number of electric substations. In this paper, Kriging interpolation method was used to calculate the impact area of the instrumental seismic intensity in Wenchuan earthquake, and to compare the intensities based on strong motion observation against the instrumental seismic intensities at locations where the observation data is available. The instrumental seismic intensities were calculated for the Wenchuan Earthquake at substations in the national power grid with voltage of 110kV or higher in areas of Mianyang, Deyang, Guangyuan and Chengdu. The cumulative Gaussian distribution function was then used to fit the relationship of the curves of the damage probabilities of high-voltage electrical equipment such as transformers, voltage mutual inductors, current mutual inductors, circuit breakers, isolating switches and lightning arrester with their instrumental seismic intensities. The damage probability density distribution curve of high-voltage electrical equipment based on the instrumental seismic intensities was obtained. The results showed that: (1) In the lower seismic intensity region, the mean instrumental seismic intensity was in good agreement with the traditional seismic intensity, but there was noticeable dispersion; in regions of intensity IX and above, the instrumental intensity was lower than the seismic intensity, but there was a lower degree of dispersion. (2) Among high-voltage electrical equipment, the transformers were most vulnerable to damage and they had some damage even under lower instrumental intensity. More damage would be produced when the instrumental intensity reached VIII or above; the second most vulnerable equipment was the circuit breaker, and the damage was most likely to occur when the instrument intensity was IX or above . (3) The damage rate curves of lightning arresters, current mutual inductors, voltage mutual inductors and isolating switches were relatively close to each other and the damage probability was the highest when the instrumental intensity was about X.

Wenchuan earthquake that occurred in China in 2008 caused severe damage to a large number of electric substations. In this paper, Kriging interpolation method was used to calculate the impact area of the instrumental seismic intensity in Wenchuan earthquake, and to compare the intensities based on strong motion observation against the instrumental seismic intensities at locations where the observation data is available. The instrumental seismic intensities were calculated for the Wenchuan Earthquake at substations in the national power grid with voltage of 110kV or higher in areas of Mianyang, Deyang, Guangyuan and Chengdu. The cumulative Gaussian distribution function was then used to fit the relationship of the curves of the damage probabilities of high-voltage electrical equipment such as transformers, voltage mutual inductors, current mutual inductors, circuit breakers, isolating switches and lightning arrester with their instrumental seismic intensities. The damage probability density distribution curve of high-voltage electrical equipment based on the instrumental seismic intensities was obtained. The results showed that: (1) In the lower seismic intensity region, the mean instrumental seismic intensity was in good agreement with the traditional seismic intensity, but there was noticeable dispersion; in regions of intensity IX and above, the instrumental intensity was lower than the seismic intensity, but there was a lower degree of dispersion. (2) Among high-voltage electrical equipment, the transformers were most vulnerable to damage and they had some damage even under lower instrumental intensity. More damage would be produced when the instrumental intensity reached VIII or above; the second most vulnerable equipment was the circuit breaker, and the damage was most likely to occur when the instrument intensity was IX or above . (3) The damage rate curves of lightning arresters, current mutual inductors, voltage mutual inductors and isolating switches were relatively close to each other and the damage probability was the highest when the instrumental intensity was about X.

It is unclear why European countries have been more severely affected by COVID-19 than East Asian countries. In this ecological study we compared the COVID-19 epidemics (cumulative incidence and mortality rates), host genetic susceptibility and national responses (testing intensity) in all European versus all Western Pacific/East Asian countries reporting cases in the first month of the epidemic. The host-genetic-susceptibility assessment was limited to the frequency of the D-allele of the angiotensin converting enzyme-1 (ACE-1) which has been found to be positively associated with COVID-19 incidence within European countries. Despite earlier epidemics, countries from the Western Pacific reported lower cumulative numbers of COVID-19 cases/100 000 inhabitants than European countries (P=0.0002). The Western Pacific countries also reported fewer cumulative COVID-19 deaths/100 000 (P=0.0024). Whilst there was little difference in the cumulative number of tests conducted/100 000, the percent of COVID-19 tests reported positive was higher in Europe than the Western Pacific (P=0.0076). The frequency of the ACE-1 D-allele was lower in the Western Pacific than European countries (P=0.0007). Our results suggest that a combination of different testing strategies and host genetic susceptibility contribute to difference in severity of the COVID-19 epidemics in the Western Pacific/East Asia and Europe.

Different cohort studies documented a lower glomerular filtration rate (GFR) in former extremely low birth weight (ELBW, <1000 g) neonates throughout childhood when compared to term controls. The current aim is to pool these studies to describe the GFR pattern over the pediatric age range. To do so, we conducted a systematic review on studies reporting on GFR measurements in former ELBW cases while GFR data of healthy age-matched controls included in these studies were co-collected. Based on 248 hits, 6 case-control and 3 cohort studies were identified, with 444 GFR measurements in 380 former ELBW cases (median age 5.3-20.7 years). The majority were small (17-78 cases) single center studies, with heterogeneity in GFR measurement (inulin, Cystatin C or creatinine estimated GFR formulae) tools. Despite this, the median GFR (ml/kg/1.73m²) within case-control studies was consistently lower (-13, range -8 to -25%) in cases, so that a relevant minority (15-30%) has a eGFR<90 mgl/kg/1.73m²). Consequently, this pooled analysis describes a consistent pattern of reduced eGFR in former ELBW cases throughout childhood. Research should focus on perinatal risk factors for impaired GFR and long-term outcome, but is hampered by single center cohorts, study size, and heterogeneity of GFR assessment tools.

The recycling, incineration, and final disposal rate of municipal solid waste (MSW) are calculated based on the total amount of waste input to each facility in many countries. These statistic data have serious limitation in setting the national goal and policy for effective waste management because it is not considering the amount of foreign objectives in the process of each life-cycle stage. This case study is to estimate the actual rates of recycling, incineration, and final disposal by material flow analysis (MFA) after the collection of MSW in Korea. The actual rates of recycling, incineration and final disposal for MSW in 2016 were 49.9%, 32.9% and 23.1% respectively, indicating that the recycling rate was lower by 10.1%, while the incineration and final disposal rates were raised by 7.6% and 8.4% respectively, compared with the statistics for current MSW. In addition, the changed actual rates of recycling, incineration treatment, and final landfill, and variation of waste treatment charge according to treated amounts per treatment method was analyzed. This results of this study will contribute to establish national level of plan on effective waste management.

The mantle mass flow interconnected with the process of Glacial Isostatic Adjustment (GIA) and the reformation of the Earth’s crust constantly perturbs the observed gravity field towards a hypothetic isostatic state. We analyse the temporal changes of the gravity field from the GRACE data, using different mathematical and/or statistical methods to detect the GIA amidst other gravity signals. A number of gravimetric post-glacial land uplift rate (LUR) modelling methods are investigated and compared with the data from a total number of 515 GPS stations and preferred GIA forward models in Fennoscandia and North America. We investigate three mathematical methods, namely regression, principal component, and independent component analysis (ICA) to extracting the GIA signal from the GRACE monthly geoid heights. We use some regularization techniques to exploit the GRACE monthly data to their maximum spatial resolution and to increase the Signal to Noise Ratio of their short wavelengths. Near the centres of the study areas the gravimetric LUR model using the fast-ICA algorithm of Hyvärinen and Oja (2000) is shown to be in a complete agreement with the GPS data and the predictions of the GIA forward models, and for the whole areas, subject to epeirogeny movement of the two regions, their discrepancies reach to the extrema at -1.8 and +3.3, and -4.5 and +7.5 mm/a, respectively. We show that the largest discrepancies between the gravimetric model using the ICA method and the GIA forward model, occur for the sub-regions likely collocated with strong ice mass change signals.

Tissue engineering is an emerging field of research due to its growing impact on the regeneration of tissue injured from damage and organ failure. Small hydrogel microspheres containing regenerative cells and stimulators can be used as building blocks to regenerate tissue by injecting them into damaged areas; a microneedle is used to minimize the incision and any associated infections. To address the need for production of a large number of microspheres for use in tissue engineering, we developed a 3D coaxial multi-nozzle flow-focusing device fabricated via a simple 3D-printing method that demonstrates a high rate of microsphere production per nozzle. This device has six coaxial microscale nozzles that produce hydrogel microspheres. Two individual parts—the inlet and nozzle—can be made separately by a 3D printer and bonded together using uncured photo-curable resin as glue. The dimensions of the microspheres are between 100 μm and 1200 μm. They are produced by adjusting the flow rate ratio between the dispersed and continuous media. A flow rate ratio of 180 demonstrated the highest microsphere production rate of 2.12e+5 microspheres per sec (0.25 mL/min). This microsphere production rate per nozzle is four times higher than that of currently available devices.

The segmentation and de-noising are basic operations, required in every signal processing and classification system. The classical segmentation and de-noising approaches are time-invariant. Consequently, it results in the post processing of an unnecessary information and causes an increase in the system processing activity and power consumption. In this context, an efficient event-driven segmentation and de-noising technique is proposed. It is founded on the principles of level crossing and activity selection. Therefore, it can adapt its sampling frequency, segmentation window length and position along with the filter order by analyzing the input signal local characteristics. As a result, the computational complexity and the power consumption of the proposed system is reduced compared to the counter ones. The suggested system performance is compared with the classical one. It is done for the case of a multi-channel Electroencephalogram (EEG) signals. Results show a noticeable compression gain with an effective adaptation of the de-noising filters order. It aptitudes a significant computational gain, transmission data rate reduction and power consumption reduction of the proposed technique, compared to the counter ones. It shows that the proposed solution is an attractive candidate to embed in the new generation EEG wearables.

The livestock sector can be a major contributor to the mitigation of greenhouse (GHG) emissions. Within the sector, beef production produces the largest proportion of the livestock sector’s direct emissions. The objective of this study was to assess the on-farm GHG emissions in semi-arid rangelands in Argentina and to identify the relationships between emissions and current farm management practices. A survey recorded detailed information on farm management and characteristics. Assessments of GHG emissions were based on the IPCC Tier 2 protocols [1]. The relationships between farm management and GHG emissions were identified using General Linear Models. Cluster analysis was used to identify groups of farms that differed from others in emissions and farm characteristics. Emissions per product sold were low on farms that had improved livestock care management, rotational grazing, received technical advice, and had high animal and land productivities. Emissions per hectare of farmland were low on farms that had low stocking rates, low number of grazing paddocks, little or no land dedicated to improved pastures and forage crops, and low land productivity. Our results suggest that the implementation of realistic, relatively easy-to-adopt farming management practices has considerable potential for mitigating GHG emissions in semi-arid rangelands of central Argentina.

The use of machine learning techniques in predictive health care is on the rise with minimal data used for training machine-learning models to derive high accuracy predictions. In this paper, we propose such a system, which utilizes Heart Rate Variability (HRV) as features for training machine learning models. This paper further benchmarks the usefulness of HRV as features calculated from basic heart-rate data using a window shifting method. The benchmarking has been conducted using different machine-learning classifiers such as artificial neural network, decision tree, k-nearest neighbour and naive bays classifier. Empirical results using MIT-BIH Arrhythmia database shows that the proposed system can be used for highly efficient predictability of abnormality in heartbeat data series.

Visible Light Communication (VLC) uses an intensity-modulation and direct-detection (IM/DD) scheme to transmit data. The light source utilized in VLC structures is constantly switched on and off rapidly, resulting in flickering. Furthermore, most of illumination systems exclude dimming support to permit customers to dim the light source to the desired stage. Therefore, the modulation scheme for information transmission in VLC should consist of flicker mitigation and dimming manage abilities. Double inverse pulse position modulation (DIPPM), sub-carrier pulse position modulation (SC-L-PPM), and M-ary variable pulse position modulation (M-VPPM) are recommended for minimizing the flicker issues and supporting an excessive degree of dimming for VLC systems. In this paper, a comparison is introduced between DIPPM, SC-L-PPM, and M-VPPM according to error performance and bit rate. In addition, a simulation is carried out to measure the optical power distribution for a LED lamp in an indoor room topology for each modulation technique. The obtained results indicated that SC-L-PPM is the best choice regarding the bit error rate (BER) and optical power distribution compared to the other two schemes. A 10^-6 BER is achieved with a very low power requirement at L=8, while a remarkable power distribution of 1.5 to 6.5 dBm is observed from 3×5×5 m³ room corners to the center, respectively. According to the bit rate, it is noticed that, M-VPPM is the most efficient one compared to the two other schemes. It achieves 2.3×10⁷ bps at signal to noise ratio (SNR) of 22 dB and M=8.

Field experiments were carried out during 2011-2014 at the Research and Experimental Center to Combating Desertification located in the Elsen Tasarkhai station of central Mongolia. The study was aimed to identify the effects of oxidized brown coal humic acid fertilizer on the relative growth rate of several trees for forest rehabilitation. The trees used were Populus sibirica, Salix ledebouriana and Acer tataricum. The experiment was carried out with the concentrations of 2,000, 10,000 and 20,000 mg L-1 of humic acid fertilization treatments. The measurement of relative height growth rate (RHGR) was conducted for a period of 4 years. The treatments showed significant differences within humic fertilizer concentrations which differed depending on the species. Compared to the monthly RHGR over the study, the treatment of fertilizers were significantly better for tree growth. P. sibirica in the 10,000 and 20,000 mg L-1 humic acid fertilizers had significant height growth rates. In addition, when the humic acid treatments were compared to control, A. tataricum decreased over the years which were statistically significant for high growth rate and a positive effect of humic acid fertilization treatments was observed. Furthermore, results showed that oxidized brown coal humic acid fertilizers as organic fertilizer can have a positive effect for the growth of A. tataricum during the study years. The results showed that the soil chemical properties EC, CO2, NO3, and K2O were significant among all the treatments compared to the control. The effect on P2O5 statistically significantly increased among all the treatments. However, pH and Mg were not significant effect among all the treatments. Combining the results obtained from the oxidized brown coal humic acid fertilization with sustainable land management practices can help improve soil organics for environmental issues in degraded sandy soil regions.

In this study, we applied a central composite design to estimate independent variables and establish optimal conditions of filtration rate and feces production that enhance filtration of suspended organic matter by the freshwater mussels Sinanodonta woodiana. The results indicated that statistical design methodology offers an efficient and feasible approach for high filtration and low feces production condition optimization. The proposed model equation takes into account the quantitative effect of variables and also the influence of interactions among variables on mussel filtration rate. Under the optimal experimental conditions (mussel size, 13.0 ± 0.2 cm; water current, 17.5 L/h), the experimental filtration rate of 4.47 ± 1.82 L/mussel/h showed a degree of correspondence with the predicted value of 8.4 L/mussel/h, which verified the practicability of this optimum strategy.

The knowledge of protein function is essential for the study of biological processes, the understanding of disease mechanism and the exploration of novel therapeutic target. Apart from experimental methods, a number of in-silico approaches have been developed and extensively used for protein function prediction. Among these approaches, BLAST predicts functions based on protein sequence similarity, and machine learning predicts functional families from protein sequences irrespective of their similarity, which complements BLAST and other methods in predicting diverse classes of proteins including distantly related proteins and homologous proteins of different functions. However, their identification accuracies and the false discovery rate have not yet been assessed so far, which greatly limits the usage of these prediction algorithms. Herein, a comprehensive comparison of the performances among four popular functional prediction algorithms (BLAST, SVM, PNN and KNN) was conducted. In particular, the performance of these algorithms were systematically assessed by four metrics (sensitivity, specificity, accuracy and Matthews correlation coefficient) based on the independent test datasets generated from 93 protein families defined by UniProtKB Keywords. Moreover, the false discovery rates of these algorithms were evaluated by scanning the genomes of four representative model species (homo sapiens, arabidopsis thaliana, saccharomyces cerevisiae and mycobacterium tuberculosis). As a result, the substantially higher sensitivity and stability of BLAST and SVM were observed compared with that of PNN and KNN. But the machine learning algorithms (PNN, KNN and SVM) were found capable of significantly reducing the false discovery rate (SVM < PNN ≈ KNN). In summary, this study comprehensively assessed the performance of four popular algorithms applied to protein function prediction, which could facilitate the selection of the most appropriate method in the related biomedical research.

The considerable biological and medicinal activities of pyridazines has stimulated considerable research on efficient syntheses of these derivatives. In the last decade, microwave irradiation has generally been used for the energy source. As demonstrated in recent studies, pressure reactor “Q-tubes” may be used to accelerate several of these reactions in a more optimal and safer manner (compared to microwaves). In these studies there has been postulated a pathway for the formation of pyridazino[5,4,3-de][1,6]naphthyridine derivatives . In this paper we consider this pathway, and an alternate pathway, for several reactions. Contrary to the suggestion in these studies the pathway in which initial dimerization of malononitrile was postulated could be excluded based on chemical evidence. The reactions performed were the reaction of arylhydrazonals 1a,b with benzylidinemalononitrile which afforded in Q-tube the 3-acyl-4-aryl-1-phenyl-6-amino-1,4-dihydropyridazines, and the reaction of arylhydrazonals 1a,b, malononitrile 9 and aromatic aldehydes 10a-g in Q-tubes which afforded the tricyclic systems 12a-n whose structure could be established by X-ray crystal structure determination. In conclusion, we have added to the work of the recent studies by excluding a reaction pathway for one of their reaction products.

Thin films (100-400 nm) of Ba_xSr_1-xTiO₃ (0≤x≤1) deposited in RF-magnetron co-sputtering equipment are presented in this research work. The change of deposition rate, gap energy, and resistivity as a function of temperature- applied power change in the growth parameters was studied through the ISO colour-code lines constructed with MATLAB: By analysing the trend information and take into account the influence of the calculated "x" parameter with the Boltzmann profile fitting is proposed a method to allow a controlled set up of the RF-magnetron co-sputtering system and predict the E_g and resistivity values in the Ba_xSr_1-xTiO₃ solid solution with 0≤x≤1 for amorphous and crystalline phases. Also, a versatile tool to optimise the deposition process and material properties.

This research explores the adoption of advanced analytics in supply chain decision-making, emphasizing its transformative impact on organizational efficiency and strategic advantage. The study investigates the key drivers behind the adoption of advanced analytics, including the growing complexity of data, the need for agility, and the pursuit of competitive advantage and cost reduction. It identifies significant challenges such as data integration difficulties, high implementation costs, and a shortage of skilled professionals, which organizations face when integrating these sophisticated tools. Despite these challenges, the research highlights the substantial benefits of advanced analytics, including enhanced forecasting accuracy, improved supply chain visibility, optimized processes, and cost savings. The findings indicate that while the implementation of advanced analytics varies across different sectors—such as retail, manufacturing, logistics, and healthcare—the overarching themes of improved efficiency and better decision-making are consistently observed. The study also discusses future trends, noting the integration of emerging technologies such as artificial intelligence, machine learning, and blockchain, which promise to further enhance analytics capabilities and accessibility. The successful adoption of advanced analytics relies not only on technological advancements but also on fostering a data-driven organizational culture, investing in continuous learning, and ensuring robust data governance. As supply chain management continues to evolve, advanced analytics will play a crucial role in driving strategic success and maintaining a competitive edge in a complex and dynamic market environment.

This qualitative study explores the intricate impact of cultural differences on global procurement practices within multinational supply chains. Cultural dimensions profoundly influence communication dynamics, negotiation strategies, decision-making processes, and supplier relationship management in diverse global contexts. Effective cross-cultural communication is crucial for fostering trust and clarity across different cultural norms, while negotiation strategies vary based on cultural preferences for collaboration or competition. Decision-making processes are shaped by cultural attitudes towards risk tolerance, time orientation, and decision authority, influencing procurement agility and resilience. Strategic implications of cultural diversity include opportunities for innovation and localized adaptation in procurement practices, tempered by challenges such as adaptation costs and regulatory compliance. Emotional intelligence (EI) emerges as pivotal in navigating cultural complexities, enhancing stakeholder engagement, conflict resolution, and collaborative partnerships critical for sustainable procurement practices in multicultural settings. Economic factors, including stability, currency fluctuations, and market volatility, impact procurement strategies and supply chain resilience, necessitating proactive risk management and adaptive approaches. Barriers to growth in global procurement, such as regulatory complexities and geopolitical risks, require strategic planning, stakeholder collaboration, and infrastructural investments for operational continuity. By understanding and addressing cultural influences, multinational corporations can enhance cross-cultural competence, strategic decision-making, and capitalize on global market opportunities. This study contributes insights and recommendations to enhance procurement effectiveness and competitiveness in an interconnected global economy, supporting ongoing efforts to optimize global procurement practices.

In the fast-changing world of software development, the protection of software products has emerged as an imperative requirement. This paper presents a new way to increase the maturity of development teams to reach the highest level of software security. Based on these, the framework uses the Fuzzy Analytic Hierarchy Process (Fuzzy-AHP) to systematically evaluate and enhance the people maturity of software development projects. The essence of the fuzzy logic and AHP technique interaction is to handle the uncertainty and complexity of human factors and team dynamics in the evaluation framework. Using the decision-making model allows the project managers and stakeholders to determine the appropriate areas for improvement and develop the right strategies and actions to nurture a secure and mature development culture. The paper identifies 24 human success factors (HSFs) and human security vulnerabilities (HSVs) and 38 practices for addressing these HSFs and HSVs. Furthermore, we discuss the local and global ranks of each HSF and HSV practice and categorize the identified practices into 9 categories to determine the ranks and weight of each category. Based on collected data, FAHP prioritized these practices; the category “C4: Skill Development and Stakeholder Engagement” is ranked highest at rank-1 and possesses the most significant weight of 0.12435. Similarly, the highest global weight is 0.051506, and the global ranked (rank-1) HSF and HSV practice is “P15: Hands-On Practice and Stakeholder Communication”. Research evidence and case discussions show how the described framework assists in building secure software development (SSD) practices, which can be considered evidence of the application of team maturity to improve cybersecurity in organizations. Additional research directions include improving the framework, especially using highly developed learning techniques and applying the framework to other forms of development.

In today's globalized business environment, multinational corporations (MNCs) face significant challenges in achieving and sustaining effective supply chain integration across diverse cultural contexts. This qualitative research explores the influence of cultural factors on supply chain integration within MNCs, employing in-depth interviews and thematic analysis to uncover key insights. Findings reveal the complex interplay between culture and supply chain practices, highlighting challenges related to cross-cultural communication, trust-building, decision-making, and organizational culture alignment. However, the study also identifies opportunities for leveraging cultural diversity as a source of competitive advantage, emphasizing the importance of cultural intelligence and cross-cultural competence for supply chain professionals. The implications of the research extend to managerial practice, suggesting the development of culturally sensitive strategies for supply chain integration and investment in cultural training and development programs. Moreover, the study underscores the need for a holistic approach to supply chain integration that considers not only technical and operational aspects but also cultural and social dimensions. While the research offers valuable insights, limitations such as the qualitative nature of the study and the focus on supply chain managers' perspectives should be considered. Future research could address these limitations and explore the interdependencies among various contextual factors to enhance our understanding of cultural influences on supply chain integration in MNCs.

AbstractThe emergence of AI-powered deepfakes, manipulatively realistic synthetic media, raises unprecedented challenges for human information processing and decision-making. This paper explores the cognitive and emotional consequences of exposure to deepfakes, delving into how these digitally fabricated experiences can reshape perception, trust, and social interactions. By reviewing existing research and outlining potential methodological approaches, this paper aims to establish a framework for investigating the multifaceted impact of deepfakes on the human brain.BackgroundThe digital age has ushered in an era of unprecedented information abundance and accessibility. Yet, this abundance breeds vulnerability, particularly with the emergence of AI-powered deepfakes. These hyper-realistic synthetic media creations present a potent threat to the fundamental trust and integrity of information sources. Deepfakes have infiltrated various domains, from entertainment and social media to politics and journalism, blurring the lines between truth and fabrication. Consequently, understanding the cognitive and emotional consequences of encountering deepfakes becomes crucial for navigating this increasingly deceptive landscape.ObjectivesThis research aims to: Investigate how exposure to deepfakes impacts various cognitive functions, including perception, attention, memory, and decision-making. Elucidate the emotional responses elicited by deepfakes and their underlying neural mechanisms. Evaluate the role of individual differences, such as susceptibility to deception and emotional sensitivity, in mediating the impact of deepfakes. Develop a comprehensive framework for understanding the multifaceted influence of deepfakes on the human brain. Results (anticipated)This research is expected to yield insights into: The specific cognitive and emotional processes altered by deepfakes, providing evidence for potential mechanisms of deception and manipulation. The neural circuitry involved in detecting and responding to deepfakes, leading to the development of more effective detection methods. The influence of individual differences (e.g., age, cognitive style) on susceptibility to deepfakes, informing targeted interventions and educational efforts.ConclusionBy deciphering the impact of deepfakes on the human brain, this research will offer valuable tools for mitigating the harmful consequences of misinformation and promoting responsible use of this powerful technology. Ultimately, understanding how deepfakes manipulate our cognitive and emotional landscape is not merely a scientific pursuit, but a critical step towards ensuring a future where truth prevails in the digital world.

Aileen Oeberst and Roland Imhoff’s remarkable paper (Perspectives on Psychological Science 2023; 18: 1464-87). should be compulsory reading for all intelligence analysts. It offers a tantalisingly parsimonious explanation comprising the combination of strongly held prior 'beliefs' coupled with subsequent 'belief-consistent information processing' (akin to confirmation bias) - an explanation that simplifies understanding of a vast array of cognitive biases, and thereby suggests that all of these might be attenuated through the application of accessible analytical and assessment practices. What this means for intelligence analysis will be determined by the explicit and implicit 'beliefs' (or, more generally, ‘value[s]’) attributed to any evidence available, and any insight generated, to reduce decision-makers’ uncertainty and unsubstantiated certainty, and thereby offer them future advantage. Analysts are well aware that different sources of evidence (whether empirical, theoretical or entirely speculative) can assign different types and amounts of ‘prior value’ to the information available for intelligence analysis and assessment. Acknowledging such value as a potential driver of subsequent confirmation bias should help analysts guard against any inherent tendency to preference evidence solely on the basis that this was initially considered most ‘valuable’. Instead they should subject all evidence and all insight – regardless of perceived ‘value’ – to a consistent battery of systematic, rigorous and robust evaluation.

One of the most widely available and extensively produced varieties of industrial hemp, which generates a substantial amount of consumer-increasing waste in the form of hemp cellulose. In this study, recycling with a compressed and high-speed method that combines crushing and alkali treatment effectively converts leftover hemp fiber into ultrafine powder. SEM (Scanning Electron Microscopy), AFM (Atomic Force Microscope), FTIR (Fourier-transform Infrared Spectroscopy), and XRD (X-ray Diffraction) examined the original morphology of hemp fiber treated with alkali, fiber heated to 200 ℃, and crushed powder. Particle size, crystallinity, fiber surface, and strength increased and decreased. It became apparent that fiber strength decreased and fiber roughness significantly increased after alkali treatment. Fiber increased significantly, and crystallinity decreased after crushing. It was simple and effective for converting the leftover hemp fiber into micron-sized powder. In about 3 to 5 minutes, approximately 1 kg of dry ultrafine powder with a particle size of 10.44 μm was produced. This production method will significantly enhance future industrial applications of waste hemp fiber.

This paper focuses on quantifying the economic and financial viability of NB-IoT and LoRaWAN technologies, two low-power wide-area network (LPWAN) technologies with unique characteristics that make them suitable for IoT applications. The purpose of the study is to propose an artefact for performing life cycle cost analysis and demonstrate its application to these technologies. The methodology uses pragmatic computational tools to facilitate the analysis and considers all relevant economic and financial factors, such as operating costs, equipment costs, and revenue potential. The main finding of the study is that NB-IoT and LoRaWAN technologies have different cost structures and revenue potentials, which may affect their economic and financial viability for different IoT applications. Ultimately, the study concludes that a comprehensive life cycle cost analysis is critical to making informed decisions about technology adoption, and that the proposed methodology can be applied to other IoT technologies to gain insight into their economic and financial viability.

Directed movement towards a target requires spatial working memory, including processing of sensory inputs and motivational drive. In a stimulus-driven, operant conditioning paradigm designed to train zebrafish, we present a pulse of light via LED’s and/or sounds via an underwater transducer. A webcam placed below a glass tank records fish swimming behavior. During operant conditioning, a fish must interrupt an infrared beam at one location to obtain a small food reward at the same or different location. A timing-gated interrupt activates robotic-arm and feeder stepper motors via custom software controlling a microprocessor (Arduino). “Ardulink”, a JAVA facility, implements Arduino-computer communication protocols. In this way, full automation of stimulus-conditioned directional swimming is achieved. Precise multi­day scheduling of training, including timing, location and intensity of stimulus parameters, and feeder control is accomplished via a user-friendly interface. Our training paradigm permits tracking of learning by monitoring, turning, location, response times and directional swimming of individual fish. This facilitates comparison of performance within and across a cohort of animals. We demonstrate the ability to train and test zebrafish using visual and auditory stimuli. Current methods used for associative conditioning often involve human intervention, which is labor intensive, stressful to animals, and introduces noise in the data. Our relatively simple yet flexible paradigm requires a simple apparatus and minimal human intervention. Our scheduling and control software and apparatus (NemoTrainer) can be used to screen neurologic drugs and test the effects of CRISPR­-based and optogenetic modification of neural circuits on sensation, locomotion, learning and memory.

Citizen participation has always been of vital importance in decision-making processes and, likewise, joint work in the formulation and execution of projects that respond to territorial needs. This in order to ensure the best impact of public or private investment, optimizing the result and community articulation. For this reason, this investigation proposes a methodology of evaluation and prioritization of projects based on an approach integrated between the modelling in dynamics systems (SDM) and the Analytical process network (ANP), in which the citizen factors are used as qualitative and quantitative variables inside the posed balance sheet model. This is how the model developed by the Stella Architect software, it offers to the decision makers approximate information about the reality of the community, especially those who were affected by the Colombian conflict and where the expectations of a comprehensive repair could disrupt the socioeconomic system and reveal more pressing interests than those of the central government. The methodology is described by the information gotten through the participatory workshops done in the California county that belongs to the Magdalena region, this is a very affected region by the conflict in Colombia. The investigation results confirm the useful of, first of all, the use of the modelling as an information-generating tool by allowing the simulation of relevant variables in the evaluation and prioritization of projects at different moments of time and, in second place, use the knowledge of the experts that expose the ANP method for establishing the importance of each variable compared with other variables and, likewise of each project compared to the rest of the alternatives in each of the different instants of time in which the evaluation is carried out, given that the results could change in any time, the official ranking is showed after an optimization process with partial results.

This study focused on the characterization of lactic acid bacteria (LAB) in a renowned traditional Italian cheese, Pecorino di Farindola, to select an autochthonous culture and investigate its po-tential for the improvement of safety and functional properties. Two hundred and six LAB isolated throughout production and maturation from nine cheese lots of three farms were identified by 16S rRNA gene sequencing and tested for the presence of genes encoding virulence factors, vancomycin resistance (for enterococci), biogenic amines (BAs) and bacteriocin production, for antimicrobial activity, and for the capacity to survive in the gastro-intestinal tract (GIT) based on tolerance to low pH and bile salts and adhesion to CaCo-2 cells. A Lacticaseibacillus paracasei isolate was used in cheese making and determined a decline of spiked Listeria monocytogenes and Escherichia coli O157 faster than in control cheese. The autochthonous bacterial groups were numerically unaffected, apart from lactobacilli that were recovered in higher numbers in the cheese with added L. paracasei. Based on Repetitive Extragenic Palyndrome (Rep) PCR profiles, the added strain possibly dominated until day 88 in cheese. Results encourage further trials with autochthonous cultures to efficiently inhibit hazardous bacteria and enrich a functional microbiota in Pecorino di Farindola and similar cheeses.

The digital world has a wealth of data, such as Internet of Things (IoT) data, business data, health data, mobile data, urban data, security data, and many more, in the current age of the Fourth Industrial Revolution (Industry 4.0 or 4IR). Extracting knowledge or useful insights from these data can be used for smart decision-making in various applications domains. In the area of data science, advanced analytics methods including machine learning modeling can provide actionable insights or deeper knowledge about data, which makes the computing process automatic and smart. In this paper, we present a comprehensive view on "Data Science'' including various types of advanced analytics methods that can be applied to enhance the intelligence and capabilities of an application through smart decision-making in different scenarios. We also discuss and summarize ten potential real-world application domains including business, healthcare, cybersecurity, urban and rural data science, and so on by taking into account data-driven smart computing and decision making. Based on this, we finally highlight the challenges and potential research directions within the scope of our study. Overall, this paper aims to serve as a reference point on data science and advanced analytics to the researchers and decision-makers as well as application developers, particularly from the data-driven solution point of view for real-world problems.

This is a short introductory review on quantum-like modeling of cognition with applications to decision making and rationality. The aim of the review is twofold: a) to present briefly the apparatus of quantum information and probability theory useful for such modeling; b) to motivate applications of this apparatus in cognitive studies and artifical intelligence, psychology, decision making, social and political sciences. We define quantum rationality as decision making that is based on quantum information processing. Quantumly and classically rational agents behaves differently. A quantum-like agent can violate the Savage Sure Thing Principle, the Aumann theorem on impossibility of agreeing to disagree.Such an agent violates the basic laws of classical probability, e.g., the law of total probability and the Bayesian probability inference. In some contexts, ``irrational behavior'' (from the viewpoint of classical theory of rationality) can be profitable, especially for agents who are overloaded by a variety of information flows. Quantumly rational agents can save a lot of information processing resources. At the same time, this sort of rationality is the basis for quantum-like socio-political engineering, e.g., social laser. This rationality plays the important role in the process of decision making not only by biosystems, but even by AI-systems. The latter equipped with quantum(-like) information processors would behave irrationally, from the classical viewpoint. As for biosystems, quantum rational behavior of AI-systems has its advantages and disadvantages. Finally, we point out that quantum-like information processing in AI-systems can be based on classical physical devices, e.g., classical digital or analog computers.

This conceptual, interdisciplinary paper will start by introducing the commencement of a new era in which human society faces continuously accelerating technological revolutions, named for short ‘Padkos’. In this context, a conceptual model of sustainable development with a focus on knowledge sharing and management will be proposed. The construct of knowledge management will be unpacked into a three-layer model with a focus on the knowledge-human and data-machine spheres. Then, each sphere will be discussed with concentrating on the learning and decision- making processes, the digital supporting systems and the human actors’ aspects. Moreover, the recombination of new knowledge development and contemporary knowledge management into one amalgamated construct will be proposed. The holistic conceptual model of knowledge sharing for sustainable development is comprised by time, cybersecurity and two alternative humanistic paradigms (Homo Technologicus and Homo Sustainabiliticus). Two additional particular models are discussed in depth. First, a recently proposed model of quantum organizational decision-making is elaborated. Next, a boundary management and learning process is particularized. The paper ends with several implications for the future based on the deliberations in the paper and the models discussed.

The popularity of electronic cigarettes in the United States and around the world has led to a startling rise in youth nicotine use. The Juul e-cigarette was introduced in the U.S. market in 2015 and had captured approximately 13% of the U.S. market by 2017. Unlike many other contemporary electronic cigarette companies, the founders behind the Juul® e-cigarette approached their product launch like a traditional high-tech start-up company, not like a tobacco company. This article presents a case study of Juul’s corporate and product development history in the context of US regulatory actions. The objective of this article is to demonstrate the value of government-curated archives as leading indicators which can (a) provide insight into emergent technologies and (b) inform emergent regulatory science research questions. A variety of sources were used to gather data about the Juul e-cigarette and the corporations that surround it. Sources included government agencies, published academic literature, non-profit organizations, corporate and retail websites, and the popular press. Data was disambiguated, authenticated, and categorized prior to being placed on a timeline of events. A timeline of four significant milestones, nineteen corporate filings and events, twelve US regulatory actions, sixty four patent applications, eighty seven trademark applications, twenty three design patents and thirty two utility patents related to Juul Labs and its associates is presented spanning the years 2004 thought 2020. This work demonstrates the probative value of findings from patent, trademark, and SEC filing literature in establishing a premise for emergent regulatory science research questions which may not yet be supported by traditional archival research literature. The methods presented here can be used to identify key aspects of emerging technologies before products actually enter the market, this shifting policy formulation and problem identification from a paradigm of being reactive in favor of becoming proactive. Such a proactive approach may permit anticipatory regulatory science research and ultimately shorten the elapsed time between market technology innovation and regulatory response.

With a reduction in the mortality rate of burn patients, patient length of stay (LOS) is increasingly adopted as an outcome measure. Some studies have attempted to identify factors that explain a burn patient's expected LOS. However, few have investigated the association between LOS and a patient's mental and socioeconomic status. There is anecdotal evidence for links between these factors and uncovering these will aid in better addressing the specific physical and emotional needs of burn patients, and facilitate the planning of scarce hospital resources. Here, we employ machine learning (clustering) and statistical models (regression) to investigate whether a segmentation by socioeconomic/mental status can improve the performance and interpretability of an upstream predictive model, relative to a unitary model derived for the full adult population of patients. Although we found no significant difference in the performance of the unitary model and segment-specific models, the interpretation of the segment-specific models reveals a reduced impact of burn severity in LOS prediction with increasing adverse socioeconomic and mental status. Furthermore, the models for the socioeconomic segments highlight an increased influence of living circumstances and source of injury on LOS. These findings suggest that, in addition to ensuring that the physical needs of patients are met, management of their mental status is crucial for delivering an effective care plan.

The objective of the paper is to introduce new similarity measure for single valued neutrosophic sets based on logarithm function. We define logarithm similarity measure and their weighted similarity measure for single valued neutrosophic sets. Then we define hybrid logarithm similarity measure and weighted hybrid logarithm similarity measure for single valued neutrosophic sets. We prove the basic properties of the proposed measures. We then define an entropy function using logarithm function to determine unknown attribute weights. We develop a novel multi attribute group decision making strategy for single valued neutrosophic sets based on the weighted hybrid logarithm similarity measure. We address an illustrative example to demonstrate the effectiveness and aptness of the proposed strategies. We conduct a sensitivity analysis of the developed strategy. We also make a comparison between the obtained results from proposed strategies and different existing strategies in the literature.

Neutrosophic cubic set (NCS) is one of the important family members of neutrosophic hybrid sets. Neutrosophic cubic set has more strength than other family members of neutrosophic hybrid sets to express incomplete information due to the presence of interval valued neutrosophic set (IVNS) and single valued neutrosophic set (SVNS) in its structure. Cross entropy measure is one of the best way to calculate the divergence of any variable from the priori one variable. In this paper we first define a new cross entropy measure under NCSs environment which we call NC- cross entropy measure. We investigate the basic properties of NC-cross entropy. We also propose weighted NC-cross entropy and investigate its basic properties. We develop a novel multi attribute decision making (MADM) strategy based on weighted NC-cross entropy. To show the feasibility and applicability, we solve a MADM problem using the proposed strategy.

Exposure to even low levels of the environmental pollutant cadmium (Cd), increases the risk of kidney damage. The body burden of Cd at which kidney damage occurs is not, however, reliably defined. Here, multiple-regression and mediation analyses were applied to data from 737 non-diabetic Thai nationals, of which 32.2% had hypertension and 9.1% had an estimated glomerular filtration rate (eGFR) ≤ 60 mL/min/1.73 m2 (low eGFR). The excretion rates of Cd (ECd) and N-acetyl-β-D-glucosaminidase (ENAG), a marker of tubular injury, were normalized to creatinine clearance (Ccr) as ECd/Ccr and ENAG/Ccr. Doubling ECd/Ccr increased the risks of having a low eGFR [POR = 2.71 (95% CI:1.97, 3.74), p &lt; 0.001] and severe tubular injury [POR = 4.80 (95% CI: 1.35, 17.1), p = 0.015]. ENAG/Ccr was strongly associated with ECd/Ccr in both men (β = 0.447, p &lt;0.001) and women (β = 0.394, p &lt;0.001), while showing a moderate inverse association with eGFR only in women (β = −0.178, p = 0.002). A moderate association of ENAG/Ccr and ECd/Ccr was found in the low- (β = 0.287, p = 0.001), and the high-Cd body burden groups (β = 0.145, p = 0.004), but ENAG/Ccr was inversely associated with eGFR only in the high-Cd body burden group (β = −0.223, p &lt;0.001). These findings together with an insignificant mediated effect suggested that Cd-induced injury that causes release of NAG plays little or no role in the nephron destruction that reduces GFR.

Background: Diagnosis of acute kidney injury (AKI) relies on serum creatinine (SCr) changes. This study investigated if urinary aminopeptidases are early and predictive biomarkers of cardiac surgery associated-AKI (CSA-AKI). Methods: Glutamyl aminopeptidase (GluAp), alanyl aminopeptidase (AlaAp), dipeptidyl peptidase-4 (DPP4), proteinuria, albuminuria, N-acetyl-β-D-glucosaminidase (NAG) and neutrophile gelatinase-associated lipocalin (NGAL) were measured in urine samples from 44 patients at arrival in Intensity Care Unit (ICU) after cardiac surgery. Sensitivity, specificity, positive and negative predictive value for diagnosis of stages 1, 2 and 3 of AKI were analyzed for the highest quartile of each marker. We also studied the relationship with SCr after surgery, 6- and 12-months glomerular filtration rate (GFR) and other long-term events over the next 5 years. Results: GluAp diagnosed the maximal number of patients that developed stage 2 or 3 of AKI, increasing diagnostic sensitivity from 0 to 75 %. Besides, GluAp and DPP4 was related to the decrease in GFR at 6- or 12-months after surgery. Conclusions: Urinary aminopeptidases are a potential tool for the early diagnosis of CSA-AKI, being GluAp the most effective marker for diagnosing stages 2 or 3 of AKI at ICU admission. GluAp and DPP4 serve as predictive biomarkers for the decrease in GFR.

Cancer patients, susceptible to severe COVID-19 outcomes, exhibit varied vaccine responses, particularly those who are receiving chemotherapy. This prospective cohort study enrolled 115 cancer patients, and data from 91 patients who received two doses of COVID-19 vaccines were analyzed. Blood was drawn at baseline, day 28, and 6 months post-second dose for neutralizing antibody analysis. The primary outcome was seroconversion rate against wild type and Omicron at day 28. Secondary outcomes included seroconversion at 6 months, factors associated with seroconversion, and safety. Of the 157 cancer patients screened, 91 were enrolled, with 45% receiving chemotherapy. Seroconversion rates at day 28 were 77% for the wild type and 62% for Omicron. Chemotherapy did not affect seroconversion (p=0.789 for wild type, p=0.597 for Omicron). Vaccine type positively correlated with seroconversion, with an adjusted ORR of 25.86 (p=0.029) for the wild type and 17.38 (p<0.001) for Omicron with the primary heterologous vaccine. Adverse events were grade 1 in 34.0% and grade 2 in 19.7% of participants. Despite lower seroconversion against Omicron, no difference was noted between chemotherapy and non-chemotherapy groups. COVID-19 vaccinations demonstrated good tolerability. This data underscores vaccine efficacy considerations in cancer patients, informing tailored strategies for this vulnerable population.

The NW-SE trending dextral strike-slip faults on the north side of the Tian Shan play an important role in accommodating the crustal shortening, which mainly includes the Karatau fault, Talas-Fergana fault, Dzhalair-Naiman fault, Aktas fault, Dzhungarian fault (also named Bolokenu-Aqikekuduk fault) and Chingiz fault. The classic viewpoint is that the strike-slip fault is the adjustment product caused by the difference of the crustal shortening from west to east. Another viewpoint attributes the dextral strike-slip fault to large-scale sinistral shearing. The Alakol Lake Fault is situated along the northern margin of the Dzhungarian Gate, stretching for roughly 150 km from Lake Ebinur to Lake Alakol. Our team utilized aerial photographs, Satellite Stereo-imagery, and field observation to map the distribution of the Alakol Lake fault. Our findings provided evidence supporting the assertion that the fault is a dextral strike-slip fault. In reference to its spatial distribution, Lake Alakol is situated in a pull-apart basin that lies between two major dextral strike-slip fault lines: the Chingiz and Dzhungarian faults. The Alakol Lake Fault serves as a connecting point for these two faults, resulting in the formation of a mega NW-SE dextral strike-slip fault zone. According to our analysis of the dating samples taken from the alluvial fan, as well as our measurement of the displacement of the riser and gully, it appears that the Alakol Lake fault has a dextral strike-slip rate of 0.8-1.5mm/yr. The strike-slip rate of the Alakol Lake fault is comparatively higher than that of the Chingiz fault in the northern region (~0.7 mm/yr), but slower than that of the Dzhungarian fault in the southern (3.2-5 mm/yr). The Chingiz-Alakol-Dzhungarian fault zone shows a gradual decrease in deformation towards the interior of the Kazakhstan platform. We contend that the rate of deformation observed is better explained by the crustal shortening adjustment model, rather than the large-scale sinistral shearing model.

Accurate estimation of livestock carrying capacity (LCC) and implementing an appropriate actual stocking rate (ASR) is key to sustainable management of grazing adapted alpine grassland ecosystems. Reliable determination of aboveground biomass is fundamental to these determinations. Peak aboveground biomass (AGBP) captured from satellite data at the peak of the growing season (POS) is widely used as a proxy for annual aboveground biomass (AGBA) to estimate LCC of grasslands. Here we demonstrate limitations of this approach and highlight the ability of POS in the estimation of ASR. We develop and trail new approaches that incorporate remote sensing phenology timings of grassland response to grazing activity, considering relations between biomass growth and consumption dynamics, in efforts to support more accurate and reliable estimation of LCC and ASR. Results show that based on averaged values from large-scale studies of alpine grassland on the Qinghai-Tibet Plateau (QTP), differences between AGBP and AGBA underestimate LCC by about 31%. Findings from a smaller-scale study that incorporate phenology timings into estimation of annual aboveground biomass reveal that Haibei alpine meadows were overgrazed by 11.5% during the study period from 2000-2005. The methods proposed can be extended to map grassland grazing pressure by predicting LCC and tracking ASR, thereby improving sustainable resource use in alpine grasslands.

Yellow eels were sampled by electrofishing in 1979, 1980 and 1981 in Vester Vedsted Baeck, Denmark, stem 6 km, catchment 24 km², with outlet to the North Sea. Yellow eels were aged by burning the otoliths. The eels were not sexed, and they varied from 6.5 to 44 cm in length. The ages varied from 0+ to 10+ year. The annual growth rate ∆ varied from 3.4 cm for 0+ eel to 2.2 cm for 10+ eel with a mean of 3.1 cm. Body mass wet wt. was recalculated to Kcal energy, with an annual growth rate ∆ of 5.33 Kcal. In contrast to body mass, the annual growth rate ∆ in Kcal increased with age. Von Bertalanffy growth trajectory (cm) of length-at-age was calculated and L∞ = 118.4 cm. Annual natural mortality M was estimated, and M was significantly depending on body mass, i.e. high M and low body mass vs. low M at high body mass. The biological production was calculated to 13.5 g wet weight m^-2 year^-1. Total 780 eel stomachs were analyzed, of which 287 (37%) were empty. The weight of food content (2.1% of eel body mass) increased proportional with eel body mass. Chironomid larvae, Ephemeroptera nymph, Simulium larvae and Gammarus pulix were the dominating food taxa, followed by Trichoptera larvae. Size of prey were independent on length of eel.

Comprehensively understanding the spatial ecology and habitat preferences of endangered species is essential for population restoration and conservation. We investigated the home range and movement of the endangered Amur soft-shell turtle (Pelodiscus maackii) in the Ussuri River, Heilongjiang Province, Northeastern China. The study involved tracking 19 Amur soft-shell turtles from late June to mid-October, 2022, resulting in complete and partial home range size data for eight subadults and two adults, respectively. The primary analysis focused on eight subadults, and the models that best described daily movement were identified. We also explored the potential factors influencing home range size. Mean movement rate ranged from 39.18 ± 20.04 m to 72.45 ± 29.36 m and was positively correlated with the linear home range and water temperature. The most insightful home range estimate was a 95% kernel density estimate, employing likelihood cross-validation smoothing with constraints set to the river boundaries. The mean home range size was 1.02 ha and was not correlated with body size. Subadults tended to establish well-defined home ranges over time; whereas, defining home ranges for adults proved challenging. This research addresses a gap regarding the ecology of the Amur soft-shell turtle and provides a foundation for future conservation plans.

Quantifying different stocking rates effects in three study areas placed at Mediterranean forest (Cuenca, Spain) was conducted by applying a multiparametric soil quality index, SQI, developed in undisturbed forest soils (> 40 years). The main objective is to advance in the development and application of multiparametric indexes which allow for soil condition assessment. For it, is analyse the effectiveness of a multiparametric soil quality index (SQI) as an indicator livestock impacts on the soil in mediterranean forests. Control areas without stocking rates were compared in forest stands with different age (Thicket forest stand, < 30 years; High polewood forest stand, 30-60 years; Old growth forest stand, > 60 years); with various intensity grazing areas (permanent livestock passage: inactive sheepfold for 2-3 years, and active sheepfold; intermittent livestock passage: bare soil, pine stand, scrubland). The multiparametric soil quality index (SQI) applied sensitive to changes in forest ecosystems depending of different stocking rates. However, for even more preci-sion to assess cattle alteration, multiparameter index recalibrated, creating a new one; Soil Status Index by Livestock (SSIL). Correlation between quality ranges obtained with both indexes in dif-ferent study areas suggest that SSIL can be considered a livestock impact reference indicator in Mediterranean forest soils.

a sensorless control scheme based on novel power converging law sliding mode observer is suggested to realize the sensorless control for the permanent magnet synchronous motor (PMSM). Firstly, by introducing a new power converging law, the problem of slow converging speed/large chattering value dilemma in the conventional converging law is solved; Secondly, in view of the shortcomings of the conventional position and speed estimation algorithm, the high-frequency buffeting in the sliding mode observer will be expanded, a phase-locked loop (PLL) velocity and position estimation strategy is adopted to replace it. Finally, through Matlab/Simulink modeling and motor speed regulation platform experimental results, the sensorless position and speed estimation technology proposed in this paper can respond to the starting speed command of 1000 r/min within 0.05 s, and the starting process has no overshoot. When disturbed by 10Nm loading, the speed fluctuation value can be controlled within 1%.

Obesity is invariably accompanied by autonomic dysfunction, although data in pediatric populations are conflicting. We conducted a systematic review and meta-analysis of 12 studies (totaling 1102 participants) comparing obese and normal-weight subjects (5-18 years of age), defined as body mass index &gt;95th or &lt;85th percentile, respectively. Using a random-effects model, we report the standardized mean differences (SMD) of sympathetic and vagal indices, calculated by heart rate variability. Autonomic dysfunction was present in the obese group, based on the average SMD in the standard deviation of sinus intervals (at -0.5340), and on the ratio of low (LF) to high (HF) frequency spectra (at 0.5735). There was no difference in sympathetic activity, but the heterogeneity among the relevant studies weakens this result. SMD in HF (at 0.5876), in the root mean square of successive differences between intervals (at -0.6333), and in the number of times successive intervals exceeded 50ms divided by the total number of intervals (at -0.5867) indicated lower vagal activity in the obesity group. Thus, autonomic dysfunction is present in obese children and adolescents, attributed to lower vagal activity. Further studies on autonomic function are needed in various pediatric cohorts, placing emphasis on sympathetic activity.

Stress can reduce the accuracy of radiation therapy owing to muscle contraction and changes in breathing patterns. This study aimed to predict stress in patients before each treatment session using artificial intelligence (AI) from biological signals to enhance treatment accuracy. We measured 123 stress cases in 41 patients and calculated stress scores by analyzing seven stress-related features derived from heart rate variability obtained from photoplethysmography. The study analyzed stress score distribution and observed its trend changes throughout the treatment. Before-treatment information was used to predict changes in stress features during treatment. AI models included both non-pre-trained (Decision Tree, Random Forest, Support Vector Machine, Long Short-Term Memory (LSTM), Transformer) and pre-trained (ChatGPT) models. The performance was evaluated using 10-fold cross-validation, exact match ratio, accuracy, recall, precision, and F1 score. More than 90% of the patients experienced stress during radiation therapy. From all the classifications, LSTM and prompt engineering GPT4.0 had the highest accuracy (feature classification, LSTM: 0.703, GPT4.0: 0.659, stress classification: LSTM: 0.846, GPT4.0: 0.769). Our research pioneers the use of AI and biological signals for stress prediction in radiation therapy, potentially identifying patients needing psychological support, and suggesting methods to improve radiotherapy effectiveness through stress management.

Eryngium foetidum L., a biennial herb with diverse applications in food and traditional medicine, holds economic and pharmacological significance. Given its growing commercial interest, implementing biotechnological approaches like plant tissue culture is vital for sustainable propagation and metabolite production. In this study, we investigated the in vitro photoautotrophic potential of E. foetidum, examining growth, chlorophyll a fluorescence, photosynthetic pigments, and anatomical features under different sucrose concentrations and gas exchange rates. Acclimatization and survival rates of plants after ex vitro transfer were also assessed. E. foetidum exhibited robust growth in both photoautotrophic and photomixotrophic conditions, with natural ventilation significantly enhancing plant development. Chlorophyll a fluorescence and photosynthetic performance were influenced by sucrose and gas exchange, highlighting the importance of these factors in plant micropropagation. Moreover, the species demonstrated remarkable plasticity during acclimatization, with high survival rates and rapid inflorescence emission. The research provides valuable insights into optimizing in vitro cultivation conditions for E. foetidum, emphasizing the potential for large-scale clonal propagation and exploring secondary metabolites. The observed phenotypic plasticity underscores the adaptability of the species to diverse environments. These biotechnological strategies open avenues for future studies, including the application of elicitors for enhanced secondary metabolite production.

Temperature increases mediated through climate change threaten the survival of species. It is of foremost importance to engage citizens and future generations in understanding the mechanisms through which temperatures imposes its affect. For educators though this is not straight forward as tools for examined the impact of temperature over the lifetime of an animal are prohibitively expensive. At the same time environmental educators need guidance on the appropriate study systems to use with a balance between the species having an obvious response and ensuring the outcomes are ethical and sustainable. In our study, we created and tested a cost-effective experiment meant to be used for environmental education purposes. More specifically, we tested the sensitivity of the Painted lady butterfly Vanessa cardui to temperature variations using a homemade incubator. We describe the design of this experiment and report findings on survival rate, morphological variations, pupation time, and wingspan of adults across a range of biologically relevant temperatures. The information provided give educators options for testing a variety of hypotheses with regards to the impacts of temperature using an affordable and flexible set-up. Furthermore, the findings can be used by students to develop an understanding of the ramifications of the butterflies responses in an ecological context.

The mechanical behavior, microstructures as well as the crystallographic textures of the Ti57-Nb43 alloy were investigated on cylindrical specimens compressed at high temperatures, in the range of 700-1000 °C, and strain rates between 0.001 and 1.0 s-1. Hardening, followed by softening behaviours were observed as a function of strain, due to the occurrence of dynamic recrystallization/recovery in hot deformation. The modified five-parameter Voce type equation described well the stress-strain curves, but for the present alloy, it was also possible with only four parameters. A new two-variables polynomial function was employed on the four parameters that described well the flow curves as a direct function of temperature and strain rate. It permitted to reduce the number of parameters and had the predictive capacity for the flow stress at any temperature, strain, and strain rate in the investigated range. The crystallographic textures were similar at all temperatures with an increase of intensity from 900 °C. The textures could be characterized by a double &lt;100&gt; and &lt;111&gt; fiber and a unique component of (001)&lt;110&gt;, the latter inherited from the initial hot rolling texture. Viscoplastic polycrystal self-consistent deformation modeling reproduced the measured textures showing that dynamic recrystallization did not alter the development of the deformation texture, only increased it intensity.

Composite polymolecular separation membranes were prepared by combining multi-branched ZIF-L with high porosity electrospinning nanofibers PI. Meanwhile, PDA and PEI were introduced into the membrane in order to improve its adhesion. The new membrane is so called “PI@PDA@PEI/ZIF-L-4” composite membrane; compared with PI@PDA@PEI/ZIF-8 composite membrane, the new membrane’s filtration rates for heavy metal ions such as Cd2+, Cr3+ and Pb2+ were increased by 7.0%, 6.6% and 9.3%, respectively. Furthermore, the new membrane has a permeability up to 1,140.0 L·m−2·h−1·bar−1, and were presenting a very stable performances after four repeated uses. The separation mechanism of PI@PDA@PEI/ZIF-L composite membranes was further analyzed in order to provide a base support for producing separation membranes with high barrier rate and high flux.

Polyhedral Oligomeric Silsesquioxanes (POSS) are one of the smallest silica nano particles. The presence of ordered ladder-like or cage conformation in their structure leads to remarkable thermal stability far greater than that for a linear polysiloxane. Reinforcement with nano particles is one of the recently favored strategy used to enhance the performance of polymers materials. The cyclic silica structure present in POSS ensures excellent thermal and mechanical stability. As a reinforcing filler, POSS can enhance the resistance of polymer matrix against pyrolysis and corrosion. In this paper, amine-terminated POSS with ladder like structure was synthesized by condensation of hydrolyzed aminosilane coupling agent. The ladder-like structure of POSS severely limits the motion of the chain backbone. The absence of phase transition for the synthesized POSS was confirmed by differential scanning calorimetry (DSC). Thermogravimetric analysis (TGA) was utilized to evaluate the thermal stability of POSS. TGA data show that the ladder-like POSS reported here has high char yield of about 75 % in nitrogen atmosphere and 54% in air atmosphere at 800℃. The TGA derivative curves show that the degradation of ladder-like POSS involves multiple stages and that the degradation rate is directly proportional to the heating rate. With the aid of Fourier Transform Infrared Spectroscopy (FT-IR), the cyclic structure of Si-O-Si bonding was determined to be the predominant structure. By analyzing the FTIR spectra of the cured POSS residue obtained at the specified temperatures, the detailed degradation mechanism of POSS was inferred. From the FTIR spectra of the low temperature cured samples, it was shown that the terminal silanol group was eliminated below 400℃. Some intermediate polymeric siloxane structures were observed by means of FT-IR and they eventually transitioned into silica which is the final product of pyrolysis of POSS. The presence of the FTIR transmission peaks at 1000 and 1100 cm-1, due to asymmetrical vertical and horizontal stretching of Si-O-Si, were the key evidence for the inferred ladder-like structure of POSS.

Titanium oxynitride thin films are deposited by DC reactive magnetron sputtering. A pure titanium target is sputtered in a reactive atmosphere composed of argon, oxygen and nitrogen gases. The oxygen mass flow rate as well as that of the nitrogen gas are both pulsed during the deposition time using an independent and rectangular signal for each reactive gas. A constant pulsing period T = 45 s is applied for both reactive gases and a delay time  of 34 s between N2 and O2 injection times is set for all depositions. Oxygen and nitrogen duty cycles are systematically and independently changed from 0 to 100% of their pulsing period. From real time measurements of the Ti target potential and total sputtering pressure, it is shown that the reactive process alternates between oxidized, nitrided and elemental sputtering modes as a function of the oxygen and nitrogen injection times. The full poisoning of the Ti target surface by oxygen and/or nitrogen can be avoided for some given ranges of O2 and N2 duty cycles. Deposition rates of titanium oxynitride films are substantially enhanced and can be adjusted between that of pure Ti and TiN films with a gradual transition of their optical transmittance in the visible range. These results support that titanium oxynitride compounds exhibiting absorbent to transparent behaviors can be precisely sputter-deposited by means of a two reactive gases pulsing process.

The G-NUMEN array is the future gamma spectrometer of the NUMEN experiment (Nuclear Matrix Element for the Neutrinoless double beta decay), to be installed around the object point of the MAGNEX magnetic spectrometer at the INFN-LNS laboratory.. This project aims at exploring Double Charge Exchange (DCE) reactions in order to obtain crucial information about the neutrinoless double beta decay (0νββ). The primary objective of the G-NUMEN array is to detect the gamma rays emitted from the de-excitation of the excited states populated via DCE reactions with good energy resolution and detection efficiency, amidst a background composed of transitions from competingreaction channels with far higher cross-sections. To achieve this, the G-NUMEN signalswill be processed in coincidence with those generated by the detection of the reaction ejectiles in the MAGNEX Focal Plane Detector(FPD). Under the expected experimental conditions, G-NUMEN detectors will operate at high counting rates, of the order of hundreds of kHz per detector, while maintaining excellent energy and timing resolutions. The complete array will consist of over 100 LaBr3(Ce) scintillators. Initial tests have been conducted on the first detectors of the array, allowing for the determination of their performance at high rates.

The nature of the fracture and fragmentation process of concrete medium under blast loading is the transformation process of the medium from continuum to discontinuity, coupled with the significant rate correlation of concrete medium, its mechanical behavior presents a high degree of complexity. Problems such as grid distortion and even negative volume are often encountered in the finite element method and others when solving this problem, while the material point method can effectively avoid these problems. In addition, the widely used HJC concrete constitutive model does not take into account the segmented characteristics of the calculation function for dynamic increasing factor. Therefore, in this paper, firstly, the calculation function for dynamic increasing factor in the HJC concrete model is modified by SHPB experiment, and the improved HJC concrete model is proposed; secondly, the material point method simulation program is developed, and the improved HJC concrete model is embedded into the simulation program; finally, the simulation program is verified by numerical examples, and the results show that the developed simulation program can better simulate the fracture and fragmentation process of concrete medium under blast loading, especially the pulverization characteristics of the medium in the near zone of the load.

Machining titanium alloy (Ti6Al4V) used in orthopedic implants by conventional metal cutting processes is challenging due to excessive cutting forces, low surface integrity and tool wear. To overcome these difficulties and for ensuring high-quality products, various industries employ wire electrical discharge machining (WEDM) for precise machining of intricate shapes in titanium alloy. The objective is to make WEDM machining parameters as efficient as possible for machining the bio-compatible alloy Ti6Al4V using box-behnken design (BBD) and Non-dominated Sorting Genetic Algorithm II (NSGA II). A quadratic mathematical model is created to represent the productivity and the quality factor (MRR and surface roughness) in terms of varying input parameters, such as pulse active (Ton) time, pulse inactive (Toff) time, peak amplitude (A) current and applied servo (V) voltage. The established regression models and related prediction plots provide a reliable approach for predicting how the process variables affect the two responses viz MRR and SR. The effects of four process variables on both the responses were examined, and the findings revealed that the pulse duration and voltage has a major influence on the rate at which material is removed (MRR) whereas pulse duration influence quality (SR).  The trade-off between MRR and SR, when significant process factors are included emphasizes the need for a reliable multi-objective optimization method. The intelligent metaheuristic optimization method named non-dominated sorting genetic algorithm II (NSGA II) is utilized to provide pareto optimum solutions in order to achieve high material removal rate (MRR) and low surface roughness (SR).

Abstract: Background and Objectives: Holter-based late potentials (LPs) are useful for predicting lethal arrhythmias in organic cardiac diseases. Although Holter-based LPs exhibit diurnal varia-tion, no studies have evaluated the optimal timing of LP measurement over 24 h for predicting lethal arrhythmia that leads to sudden cardiac death. Thus, this study aimed to validate the most effective timing for Holter-based LP testing and to explore factors influencing diurnal variability of LP parameters. Materials and Methods: We retrospectively analyzed 126 patients with post-myocardial infarction (MI) status and 60 control participants who underwent high-resolution Holter electrocardiography. Among the 126 post-MI patients, 23 developed sustained ventricular tachycardia (VT) (the MI-VT group), while 103 did not (the MI-non-VT group) during the obser-vation period. Holter-based LPs were measured at 0:00, 4:00, 8:00, 12:00, 16:00, and 20:00, and heart rate variability analysis was simultaneously performed to investigate factors influencing diurnal variability of LP parameters. Results: Holter-based LP parameters showed diurnal variation with significant deterioration at night and improvement during the day. Assessment at the time with the longest duration of low-amplitude signals <40 μV in the filtered QRS complex terminus (LAS40) gave the highest receiver operating characteristics curve (area under the curve, 0.659) and the highest odds ratio (3.75; 95% confidence interval, 1.45–9.71; p=0.006) for predicting VT. In the multiple regression analysis, heart rate and noise were significant factors affecting LP parameters in the MI-VT and control groups. In the non-VT group, LP parameters were significantly influenced by noise and parasympathetic heart rate variability parameters such as logPNN50. Conclusions: For Holter-based LP measurements, test accuracy was higher when LP was measured at the time of the highest or worst value of LAS40. Changes in autonomic nervous system activity, including heart rate and noise levels, were factors influencing diurnal variability.

Cardiac damage has been attributed to SARS-Cov-2-related pathology contributing to increased risk of vascular events. Heart rate variability (HRV) is a parameter of functional neurocardiac integrity with low HRV constituting an independent predictor of cardiovascular mortality. Whether structural cardiac damage translates into neurocardiac dysfunction in patients infected with SARS-CoV-2 remains poorly understood. Hypothesized mechanisms of possible neurocardiac dysfunction in COVID-19 comprise direct systemic neuroinvasion of autonomic control centers, ascending virus propagation along cranial nerves and cardiac autonomic neuropathy. While the relationship between the autonomic nervous system and the cytokine cascade in general has been studied extensively, the interplay between the inflammatory response caused by SARS-CoV-2 and autonomic cardiovascular regulation remains largely unclear. We reviewed the current literature on the potential diagnostic and prognostic value of autonomic neurocardiac function assessment via analysis of HRV in patients with COVID-19. Furthermore, we discuss potential therapeutic targets of modulating neurocardiac function in this high-risk population.

In the Mediterranean Sea, there are two critical issues affecting marine benthic biocenosis: the sedimentation process and the increasing trend in marine biodiversity loss. These processes are very marked along the western side of Calabria coastline where siltation is one of the main reasons for the regression of Posidonia beds in the regional coastal waters. This research aims to investigate the relationships between the geomorphological features of the debris source areas, represented by fluvial basins, and the distribution of Posidonia meadows. So, a geomorphological study of the Tyrrhenian fluvial basins with area greater than 200 km2 and its correlation with the mapping of the meadows in the Calabria Tyrrhenian waters was carried out. Furthermore, in order to assess the increased level of burial in a Posidonia oceanica meadow and its health state over time, a program of Posidonia monitoring was undertaken between 2000 and 2010, in a test area located in the Marine Regional Park of Isca (Calabria, Southern Italy). The results of this survey highlighted that, at the beginning of the study period, for a silting rate of 4 - 5 cm/year, the meadow suffered a reduction of its photosynthetic ratio with a rate of mortality of 50%. In the following years, the siltation rate reach 12 cm/year in 2010 and the meadow began to disappear. Therefore, the marine pollution by sedimentation represents a serious factor for the regression of Posidonia oceanica meadows, enhancing the risk of a gradual loss in marine biodiversity.

The growing production and application of carbon-based nanomaterials (CNMs) represent possible risks for aquatic systems. However, the variety of CNMs with different physical and chemical properties, and different morphology complicated the understanding of their potential toxicity. This paper aims to evaluate and compare the toxic impact of four most common CNMs, namely multiwalled carbon nanotubes (CNTs), fullerene (C60), graphene (Gr), and graphene oxide (GrO) in marine microalgae Porphyridium purpureum. The microalgae cells were exposed to the CNMs for 96 h and measured by flow cytometry. Based on the obtained results, we determined no observed effect level (NOEL), calculated EC10 and EC50 concentrations for growth rate inhibition, esterase activity, membrane potential, and reactive oxygen species (ROS) generation changes for each tested CNMs. According to the sensitivity (growth rate inhibition) of P. purpureum, the used CNMs can be listed in following order: CNTs &gt; GrO &gt; Gr &gt; C60. The toxicity of CNTs was significantly higher than the toxic effect of the other used CNMs and only this sample caused increase of ROS generation in microalgae cells. This effect caused by trace metal residuals in CNTs and high affinity between particles and microalgae associated with the presence of exopolysaccharide coverage on P. purpureum cells.

Hyper duplex stainless steels, HDSS, are a new alloy group of duplex stainless steels with the highest corrosion resistance and mechanical properties among the existing modern stainless steel. Due to the addition of extra high content of alloying elements, e.g. Cr, Ni, Mo, etc., the crystallization behavior of the δ-ferrite from the liquid is of vital importance for controlling the steel properties. In this work, the effect of cooling rate (i.e. 4°C/min and 150 °C/min) on the growth process of δ-ferrite in S33207 during the solidification process was investigated using high-temperature confocal scanning laser microscopy (HT-CLSM) in combination with electron microscopes and thermodynamic calculation. The results showed that the solidification mode of S33207 steel was a ferrite-austenite type (FA mode). L→δ transformation occurred at a certain degree of supercooling, and merging occurred during the growth of δ phase dendrites. Similar microstructures were observed after solidification under these two different cooling rates. The variation of area fraction of δ ferrite at the free surface and temperature as well as time during solidification of S33207 steels were calculated at different cooling rates of 4 °C/min and 150 °C/min, respectively. The current HT-CLSM study provides in-situ experimental evidence to confirm that a low cooling rate favored the growth of primary δ-ferrite, whereas a high cooling rate favored the nucleation of primary δ-ferrite during the solidification process. The post-microstructure as well as composition evolution is also briefly investigated. This work shed light on the real time insights for the crystallization behavior of hyper duplex stainless steels during solidification, which aims to contribute to the process control of manufacturing of this steel grade.