We give a series of numerical examples of competitive evolution in the predation system, showing in some cases how the choice is made to increase the efficiency of the predation mechanism (or other significant parameters) to the detriment of populations (both of prey and predators). We then develop the mathematical theory that enables us to understand the causality involved, and identify a trend towards the emergence of the functional predation mechanism as such (and not of populations of the species involved). The realization of this trend only takes place when the conditions for it are offered by the hazards proposed to successive competitive choices. The logical structure of this trend is similar to that of the « tendency of rate of profit to fall » in certain economic models.

EV transmissions operate at high speeds, upto 30,000 rpm. High speed operation puts higher demands on bearings, seals, and gears. Bearings in EV transmissions are prone to electrically induced bearing damage and may exhibit signs of pitting and fluting. Surface-initiated rolling contact fatigue is another common problem gaining increased attention lately. Most EV transmissions require a coupling between an oil-lubricated gearbox to an electrical motor that runs with minimal lubrication at very high rpm. High mechanical and thermal stresses the seals are exposed to under starved lubrication conditions have a detrimental impact on their service life. Hence, proper lubrication is critical. In general, EV transmission fluids call for a somewhat different spectrum of properties compared to conventional ATF. Gear tribology simulations open new ways to the design and optimization of lubrication for EV transmissions. Additionally, such simulations can also provide valuable insights into the effects of different oil properties on cooling and lubrication efficiencies, thereby helping in matching the lubricant and hardware characteristics for optimal performance. In the present communication, we demonstrate the effects of different lubricants and surface finishing technologies on the tribology of high-speed gears using tribological tests and advanced thermal elastohydrodynamic (TEHD) simulations. Important roles of lubricity additives and surface finish optimization are highlighted in conjunction with a move towards ultralow viscosity EV transmission fluids.

Abstract: The objective of these studies was to determine the dependence of the distribution of the microwave field into a grain layer and the efficiency of energy transfer from the magnetron into the grain layer, via a waveguide, on the moisture content. The subject of the research was a semicircular waveguide with slot radiators that supply a microwave field to the grain surrounding the waveguide. The change in the directional diagram of the microwave field in the longitudinal direction of the waveguide was studied using CST Microwave Studio 2019 software. It was found that the change in the moisture content of the processed grain leads to a significant change in both the radiation and total efficiency values of the waveguide. For instance, the radiation efficiency of the waveguide decreases by 15.1% (from 68.729 dB to 58.294 dB) when the moisture content of the processed grain increases from 14% to 26%. The total radiation efficiency also decreases (from 11.27 dB to 21.7 dB). In this case, not only the value of the radiation efficiency but also the shape of its dependence on the magnetron radiation frequency change. Data were obtained on the change in the Q-factor for resonators in which grain layers are processed, depending on the variation in grain moisture content.

Due to combined climate and biodiversity crisis, the sustainable utilization of phytogenetic resources stands as one-way alternative while nutrient management strategies gain an increasing role in agriculture. Building on previous studies regarding the Endangered local endemic of Crete (Greece) Carlina diae (Asteraceae) with medicinal and ornamental value, this investigation focused on its pilot cultivation and fertilization (foliar or root application). Foliar application included chemical fertilizer (conventional) or integrated nutrient management (INM). Root application consisted of chemical fertilizer, biostimulant, or INM with biostimulant. Above-ground biomass content of nutrients, together with leaf chlorophyll fluorescence and colour parameters (SPAD meter, DA meter, Chroma Meter) were determined. The leaf content of chlorophyll, three key antioxidant compounds and minerals’ titers were also assessed. The fertilization scheme did not influence plant growth and visually perceived quality (leaf color and shape). Notably, foliar INM fertilization increased biomass partitioning to inflorescences (harvestable organ for either medicinal or ornamental purposes), and decreased tissue water content (facilitating processing). Considering all three antioxidants together, INM with biostimulant appeared the optimum scheme, being associated with the highest (carotenoids, phenolics) or the second highest (flavonoid) content. In C. diae, therefore, INM fertilization was optimal for upgrading yield (foliar) and herbal quality in terms of antioxidant profile (INM with biostimulant), which might be embraced as an eco-friendly approach for high quality yields.

The term sustainable energy is very familiar to all of us yet its exact definition or meaning has so far been vague. To date the widely adopted definition of sustainable energy has been inspired by the definition of sustainable development formulated more than 30 years ago in the Our Common Future - the UN’s Report of the World Commission on Environment and Development. The current definition conceals the true spirit of the Report and this has some ramifications. It raises the question as to whether we have put too much emphasis on attaining the future dimension of sustainability in the middle of the situation where the energy survivability is in fact the real issue in many parts of the world. In this paper the role of energy in sustaining livelihoods of low income communities is discussed. Existing definition of sustainable energy that the whole world seems to have embraced is looked at critically and its downsides exposed. The identified pillars of sustainable energy and the associated issues is discussed and the need for an additional pillar, i.e. affordability is discussed and called for. This paper will argue that global definition of sustainable energy seems inappropriate and should be jettisoned and a more realistic definition should be formulated, adopted and embraced at local (i.e. national or regional) level taking into account local attributes and factors. The current push for a transition from the reliance on conventional energy sources to ‘cleaner’ energy sources (generally associated with renewable energy) has further exacerbated the issue of energy affordability that has made the conditions even more dire for so many groups of the world population. In the midst of this situation, those who push for a rushed energy transition seem to be those who also produce unsustainably high carbon footprint but who can easily offset their carbon foot-print through the ‘net-zero’ concept.

With the continuous update of gene editing technology, great progress has been made in livestock breeding, researchers have produced gene edited pigs, cattle, sheep and other improved livestock. Gene editing technology is a genetic means to knock in, knock out, delete, inhibit, activate or replace specific bases of DNA or RNA sequences at the genome level to achieve accurate modification, and can edit genes at a fixed point without the need for DNA templates. In recent years, although regular clusters of interspaced short palindromic repeats (CRISPR)/Cas9 system mediated gene editing technology has been widely used in animal genetic breeding research, but so far, the system's precise insertion efficiency of foreign genes is not high enough, and there are certain off-target effects, and it is not enough to be used in genome editing of large livestock such as cashmere goats. In this paper, the development status, challenges, application prospects and look into the distance of CRISPR/ Cas9-mediated precisiongene editing technology in livestock breeding were reviewed, in order to provide theoretical reference for livestock gene function analysis, genetic improvement and livestock breeding with local economic characteristics.

The ridge-furrow plastic mulching (RFPM) system and nitrogen application have been effective strategies for improving crop productivity in the Loess Plateau of China. However, it is not clear how the ridge-furrow ratio and nitrogen fertilizer type (NT) affect the utilization of water, nitrogen, heat and radiation resources for increased rain-fed wheat production. Two nitrogen fertilizer types [Traditional urea (TU) and controlled-release urea (CRU)] and four planting patterns [conventional flat planting (F) and the RFPM system of 20 cm ridge with 40 cm furrow (R2F4), 40 cm ridge with 40 cm furrow (R4F4), and 60 cm ridge with 40 cm furrow (R6F4)] were tested from September, 2018 to June, 2021 during winter wheat growing season. The results showed that the RFPM system can increase the soil thermal time (TTsoil) by 41.0–152.1°C d compared to F. The thermal effect of the RFPM system shortens the vegetative growth period and extends the reproductive growth period by 2–7 days, promoting the increase of the leaf area index (LAI) and final dry matter (DM) accumulation. These significantly increased the grain yield (GY) in the RFPM system by 51.6–115.2% and enhanced the thermal time use efficiency (TUE) by 48–99.5%, water productivity (WP) by 37.4–76.3%, radiation use efficiency (RUE) by 16.3–34.4%, and partial factor productivity of nitrogen (PFPN) by 51.6–115.2% compared to F. Although a high ridge-furrow ratio combined with CRU increased GY and resources use efficiency, it also exacerbated the soil water depletion, especially in the 40–140 cm soil layer. Overall, applying CRU in combination with the RFPM system of 40 cm ridge with 40 cm furrow maximized resources use efficiency and increased wheat production in the Loess Plateau of China.

The effects of the coolant pulsation and the film cooling with the plasma aerodynamic actuation (PAA) could be herein explored via large eddy simulations. The electrohydrodynamic force derived from the PAA was solved through the phenomenological plasma model. The Strouhal number of the sinusoidal coolant pulsation and the averaged pulsation blowing ratio were 0.25 and 1.0, respectively. Comprehensive analyses were carried out on the time-averaged flow fields, and the results revealed that the pulsed cooling jet might cause a deeper penetration into the crossflow, and this phenomenon could be remarkably mitigated by the downward force of the PAA. Furthermore, because of the coolant pulsation, the counter rotating vortex pair (CRVP) expanded to lifted off the wall less well, and the PAA lessened the negative lift-off impact and entrapment from the CRVP. Then, the spatial-temporal development of the coherent structures was figured out by the alterations of the centerline temperature, reflecting formation of the intermittent coherent structures rather than hairpin vortices due to the coolant pulsation, and their size and upcast behaviors were reduced by the PAA. Consequently, there was a basic suppression of the turbulent mixing of the cooling fluid with the crossflow. Finally, the three-dimensional streamlines confirmed that the coherent structure dynamic behaviors were significantly regulated by the PAA for alleviating the adverse influences of the coolant pulsation. In summary, through controlling how the dominating coherent structures evolve throughout time and space, the PAA can effectively increase the pulsed film cooling efficiency.

High Vacuum Flat Plate Collectors (HVFPCs) are the only type of Flat Plate Thermal Collectors capable of producing thermal energy for middle-temperature applications (until 180 °C). As the trend of research plans to develop new Selective Solar Absorbers to extend the range of HVFPC application until 250 °C, it is necessary to correctly evaluate the collector efficiency up to such temperature to predict the energy production accurately. We propose an efficiency model for these collectors based on the selective absorber optical properties. The proposed efficiency model explicitly includes the radiative heat exchange with the ambient, which is the main source of thermal losses for evacuated collectors at high temperatures. It also decouples the radiative losses that depend on the optical properties of the absorber adopted from the other thermal losses due to HVFPC architecture. The model has been validated by applying it to MT-Power HVFPC manufactured by TVP-Solar, and it has been used to predict the efficiency and energy production of HVFPC equipped with new, optimized selective solar absorbers developed in recent years.

Buildings can play an important role in reducing GHG emissions through increased energy efficiency. The European Commission issued a proposal in 2021 suggesting that all new buildings should be “zero-emission Buildings” (ZEB), aiming at a zero GHG emission building stock by 2050.The extent to which ZEB can contribute to reduced GHG emissions, however, varies between countries, due to different energy systems. It is also important to consider other environmental effects to avoid that climate benefits come with unintended consequences.Here, we explore the life-cycle environmental performance for a ZEB in a case where electricity and heating is largely fossil-free. The assessment concentrates on i) environmental impact of the use stage in relation to the product stage, ii) the interrelation between different energy sources, with attention on household electricity, and iii) the performance for more impact categories than primary energy use and climate change. While our results generally support the use of ZEBs from an environmental perspective, they also show that the climate benefit in this setting is marginal. However, given that energy systems are connected and energy savings in one place can reduce the demand for fossil energy elsewhere, the climate benefit of ZEBs is likely underestimated. Besides methdological implications for future studies, this indicates that current EU policy is promising, as incentives for implementation of ZEBs is unaffected by domestic effects.

Using graph theory, computer aided motion, static force and power flow analysis of planetary gear mechanism is realized. The motion, static force and efficiency calculations of 6HP26 automatic transmission are carried out. Based on kinematic and static force analysis model, related matrices are acquired. Hence, kinematic and static force analysis of planetary gear mechanism is achieved. The link power can be determined by the link speed and torque. Power flow diagrams of each gear are acquired. The efficiency is calculated by transmission ratio method.

Running is a basic form of human locomotion and one of the most popular sports worldwide. While the leg biomechanics of running have been studied extensively, few studies have focused on the upper-body movement. However, an effective arm swing and longitudinal rotation of the shoulders play an important role in running efficiency as they must compensate for the longitudinal torques generated by the legs. The aim of this study is to assess the upper-body rotation using wearable inertial sensors and to elucidate its relation to energy expenditure. Eighty-six junior elite middle and long-distance runners (37 female, 49 male) performed an incremental treadmill test with sensors attached on both shoulders, tibiae and the sacrum. Mean and total horizontal shoulder and pelvis rotation per stride were derived while energy costs were determined using respiratory gas analysis and blood sampling. Results show that shoulder and pelvis rotation increase with running speed. While shoulder rotation is more pronounced in female than in male runners, there is no sex difference for pelvis rotation. Energy cost of running and upper trunk rotation prove to be slightly negatively correlated. In conclusion, upper body rotation appears to be an individual characteristic influenced by a sex-specific body mass distribution.

Abstract: The traditional model of closed circuit ball milling systems has been used for several decades, however, if the classifier of the closed circuit ball mill system performs the duties of both pre-classification and check-classification, the characterization error of the traditional model is large. To address this problem, a new model is obtained by modifying and supplementing the traditional one. The most important feature of the new model compared to the traditional model is that the circulating load is considered to be the fresh feed for the entire system rather than the ball mill. The error between the slurry level height calculated using the traditional model and the actual is 52.31%, which is 13.77 times higher than that of the new model. When the relative capacity varies greatly, that of the ball mill calculated by the traditional model fluctuates between 0.95 and 1.15, while the new model is 0.6 to 1.4. The new model has a higher accuracy than the traditional model in characterizing the production status of the grinding system, which is of some significance for industrial production.

The objective of this study was to apply simulation and computational intelligence techniques using artificial intelligence and genetic algorithm for economic and environmental optimization of the reverse network (manufacturers, waste managers and recyclers in São Paulo, Brazil) of waste electrical and electronic equipment (WEEE) to promote circular economy. For the economic evaluation, the reduction of: fuel, drivers, insurance, depreciation, maintenance and charges was considered and for the environmental evaluation, the environmental impact was measured in the abiotic, biotic, water, land, air and greenhouse gases compartments. It is concluded that the optimized structure of the WEEE reverse chain for São Paulo, Brazil reduced the number of collections, making the most of the cubage. It also generated economic and environmental gains, contributing to the strategic actions of the circular economy. Thus, the proposed simulation allows replication in organizational practice, mainly to meet the 2030 agenda on reducing the carbon footprint generated in transport in large cities. Thus, this study can guide companies on structuring the reverse WEEE chain in São Paulo, Brazil for economic and environmental optimization, a relevant aspect considering the exponential generation of WEEE, requiring the implementation of the national solid waste policy, and subsequently the signature of the electronics sector agreement in São Paulo.

Cesium lead iodide (CsPbI3) perovskite nanocrystals (NCs) are a promising material for red light-emitting diodes (LEDs) due to their excellent color-purity and high luminous efficiency. However, small-sized CsPbI3 colloidal NCs, such as nanocubes, used in LEDs suffer from confinement effects, negatively impacting their photoluminescence quantum yield (PLQY) and overall efficiency. Here, we introduced YCl3 into the CsPbI3 perovskite, which formed anisotropic, one-dimensional (1D) nanorods. This was achieved by taking advantage of the difference in bond energies between Cl− and I− ions, which caused YCl3 to promote the anisotropic growth of CsPbI3 NCs. The YCl3-based nanorods improved the PLQY and storage stability by passivating the defects reducing the nonradiative recombination rates. When the YCl3-substituted CsPbI3 nanorods are applied to the emissive layer in LEDs, we achieve an external quantum efficiency of ~3.16% which is 1.86-fold higher than the pristine CsPbI3 NCs (1.69%) based LED. Notably, the ratio of horizontal transition dipole moments (TDMs) in the anisotropic YCl3:CsPbI3 nanorods was determined to be 75%, which is higher than the isotropically oriented TDMs in CsPbI3 nanocrystals (67%). This increased TDM ratio led to higher light outcoupling efficiency in nanorods-based LEDs. Overall, the results suggest that YCl3-substituted CsPbI3 nanorods could be promising for achieving high-performance perovskite LEDs.

Three-Dimensional mesoporous TiO2 scaffolds of anatase phase possess inherent eximious optical behavior that are beneficial in designing photoelectrodes for solar energy conversion applications. However, substantial efforts have been devoted in maximizing the UV and/or visible light absorption efficiency, and suppressing the annihilation of photogenerated charged species in pristine mesoporous TiO2 structure for improved solar illumination conversion efficiencies. This study provides the fundamental insights into Mxene functionalized mesoporous TiO2 as photoelectrode for the first time. This novel combination of Mxene functionalized TiO2 electrodes with and without TiCl4 treatments have been successfully optimized to intensify the process of photon absorption, charge segregation and photocurrent, resulting in superior photoelectrode performance. The photocurrent measurements of prepared photoelectrodes are significantly enhanced upon increased contents of Mxene due to improved absorption efficiency within the visible region as verified by UV–Vis absorption spectroscopy. Moreover, as evident through structural analysis, the anatase phase of TiO2 is well grown due to increased contents of Mxene and post-deposition heat treatments. Consequently, an appreciable coverage of well-developed grains on FTO surface observed in SEM images. Thereby, the newly fabricated conductive mesoporous TiO2 photoelectrodes are potential candidates for photoinduced energy conversion and storage purposes.

Solar cell layers technology has achieved global standing in the solar cell layers deposition process, and it covers the innovative methods and techniques in significant applications. Recent solar cell layers technology has an advanced interest in a refined approach to enhance performance and highlights the importance of recent proficient procedures for manufacturing. For example, the application is used to search for novel materials for solar cells' layers to clarify the current energy crisis. The technological process and various types of solar cells depend on climate change. Among them, layers of solar cells and silicon wafer solar cells are very encouraging. Solar cell layers technology has led to solar cells being a more reasonable active option in design and production. The productivities facilitated by new solar cells still need to be enhanced for the various processes involved in the additional enhancement from Copper Indium Gallium Selenide (CIGS) microfilms to solar cell crystal structure dye-sensitized solar cells. The hydrophobic coating works as an anti-dust coating, enhancing efficiency and decreasing the cost of cleaning solar cells. In Saudi Arabia Majmaah City, most solar projects are in dry regions, where the dusty weather reduces solar cell efficiency. Therefore, combining these two properties and applying an anti-reflective and superhydrophobic coating will increase solar cell efficiency by 20%. Solar cells' crystal structure results are substituted with layers or new materials to balance environmental impact and toxic nature.

Deployment of unmanned aerial vehicles (UAVs) as aerial base stations (ABSs) has been considered to be a feasible solution to provide network coverage in scenarios where the conventional terrestrial network is overloaded or inaccessible due to an emergency situation. This article studies the problem of optimal placement of the UAVs as ABSs to enable network connectivity to the users in a coverage free zone. The main contributions of this work include two approaches to position the UAVs and to assign user equipment (UE) to each UAV, such that the sum-rate and the coverage probability of the network is maximized. An approach can be selected depending on the prevailing scenario. The first approach uses clustering algorithm to determine the 2D positioning of the UAV and a matching algorithm is used for UE assignment by considering the characteristics of the air-to-ground propagation channels as well as the impact of co-channel interference from ABSs. Then it uses exhaustive search on different altitudes to find the optimal altitude. In the second approach, 2D positioning and UE assignment are done similarly to the first approach. However, the sub-optimal altitude is estimated using particle swarm optimization (PSO). The first approach is suitable for a system which has computational resource constraints or lower probability of line of sight (LoS) links. In contrast, the second approach is suitable for data rate greedy systems or a higher probability of LoS links.

Façade elements are a building component that satisfies multiple performance parameters. Among other things, “advanced façades” take advantage of hybrid solutions, such as assembling laminated materials. In addition to the enhanced mechanical properties that are typical of optimally composed hybrid structural components, these systems are energy-efficient, durable, and offer lighting comfort and optimal thermal performance, an example of which is the structural solution developed in collaboration with the University of Zagreb and the University of Ljubljana within the Croatian Science Foundation VETROLIGNUM project. The design concept involves the mechanical interaction of timber and glass load-bearing members without sealing or bonding the glass-to-timber surfaces. Following earlier research efforts devoted to the structural analysis and optimization of thus-assembled hybrid Cross-Laminated Timber (CLT)-glass façade elements, in this paper, special focus is given to a thermal and energy performance investigation under ordinary operational conditions. A simplified numerical model representative of a full-size building is first presented by taking advantage of continuous ambient records from a Live-Lab mock-up facility in Zagreb. Afterwards, a more detailed Finite Element (FE) numerical analysis is carried out at the component level to further explore the potential of CLT–glass façade elements. The collected numerical results show that CLT–glass composite panels can offer stable and promising thermal performance for façades similar to national and European standard requirements.

Facade elements are known to represent a building component with multiple performance parameters to satisfy. Among others, “advanced facades” take advantage of hybrid solutions, like the assemblage of laminated materials. In addition to enhanced mechanical properties that are typical of optimally composed hybrid structural components, these systems are energy-efficient, durable, and offer lightening comfort and optimal thermal performance. This is the case of the structural solution developed in joint research efforts of the University of Zagreb and the University of Ljubljana, within the Croatian Science Foundation VETROLIGNUM project. The design concept involves the mechanical interaction of timber and glass load-bearing members, without sealing or bonded glass-to-timber surfaces. Laminated glass infilled timber frames are recognized as a new generation of structural members with relevant load-carrying capacity (and especially the enhancement of earthquake resistance of framed systems), but also energy-efficient and cost-effective solutions.

Undoubtedly the Wageningen B-screw Series is the most widely used systematic propeller series. It is very popular to preselect propeller dimensions during the preliminary design stage before performing a more thorough optimization, but in the smaller end of the market it is often used to merely select the final propeller. Over time the originally measured data sets were faired and scaled to a uniform Reynolds number of 2·10⁶ to increase the reliability of the series. With the advent of the computer, polynomials for the thrust and torque values were calculated based on the available data sets. The measured data are typically presented in the well-known open-water curves of thrust and torque coefficients K_T and K_Q versus the advance coefficient J. Changing the presentation from these diagrams to efficiency maps reveals some unsuspected and surprising behaviours, such as multiple optima when optimizing for efficiency or even no optimum at all for certain conditions. These artefacts get more pronounced at higher pitch to diameter ratios and low blade numbers. The present work builds upon the paper presented by the author at the AMT’17 and smp’19 conferences and now includes the extended efficiency maps, as suggested by Danckwardt, for all propellers of the Wageningen B-screw Series.

Various heterogeneous devices or objects shall be integrated for transplant and seamless communication under the umbrella of internet of things (IoT). It would facilitate the open accession of data for the growth of a glut of digital services. To build a general framework of IoT is very complex task because of heterogeneity in devices, technologies, platforms and services, operating in the same system. In this paper, we mainly focus on the framework for big data analytics in smart city applications , which being a broad category specifies the different domains for each application. IoT is intended to support the vision of Smart City, where advance technologies will be used for communication for the quality life of citizens. A novel approach used in this paper, is for enhancing the energy conservation and to reduce the delay in big data gathering at tiny sensor nodes used in IoT framework. To implement the smart city scenario in terms of big data in IoT, an efficient (optimized in quality of service) WSN is required where communication of nodes is energy effcient. That is why, a new protocol QoS-IoT is proposed on the top layer of the architecture which is validated over the traditional protocols.

The study was done to investigate the kinetics of first order bioremediation. The effectiveness of remediating soils polluted with raw crude oil and treated crude oil using Aspergillus niger (fungi) and Pseudomonas aeruginosa (bacteria) were investigated. Eight systems of 500g soil sample were polluted with both raw and treated crude oil. Four systems were polluted with 40g treated crude oil while the other remaining four systems were polluted with 40g raw crude oil. Two systems with raw crude and treated crude were left as control (RCC and TCC). Raw crude samples were treated with Aspergillus niger only (RCA) and Pseudomonas aeruginosa (RCP) while treated crude samples were also treated with same (TCA) and (TCP) only. The last two systems were treated with both Pseudomonas aeruginosa and Aspergillus niger (RCAP and TCAP). The first order bioremediation kinetics and biostimulant efficiency for these systems were studied by monitoring Total Petroleum Hydrocarbon (TPH). At the end of the bioremediation period, the results obtained showed that treated crude oil polluted soil generally remediated faster and better than raw crude oil polluted soil. The highest level of bioremediation occurred in systems amended with both Pseudomonas aeruginosa and Aspergillus niger which had about 98% TPH decrease.

The grain size of CVD (Chemical Vapor Deposition) graphene was controlled by changing the precursor gas flow rates, operation temperature, and chamber pressure. Graphene of average grain sizes of 4.1 µm, 2.2 µm, and 0.5 µm were synthesized in high quality and full coverage. The possibility to tailor the thermoelectric conversion characteristics of graphene has been exhibited by examining the grain size effect on the three elementary thermal and electrical properties of σ, S, and k. Electrical conductivity (σ) and Seebeck coefficients (S) were measured in a vacuum for supported graphene on SiO₂/Si FET (Field Effect Transistor) substrates so that the charge carrier density could be changed by applying a gate voltage (V_G). Mobility (µ) values of 529~1042, 459~745, and 314~490 cm²/V·s for the three grain sizes of 4.1 µm, 2.2 µm, and 0.5 µm, respectively, were obtained from the slopes of the measured σ vs. V_G graphs. The power factor (PF), the electrical portion of the thermoelectric figure of merit (ZT), decreased by about one half as the grain size was decreased, while the thermal conductivity (k) decreased by one quarter for the same grain decrease. Finally, the resulting ZT increased more than two times when the grain size was reduced from 4.1 µm to 0.5 µm.

In common model testing practise, the measured values of the self propulsion test are split into the characteristics of the hull, the propeller and into the interaction factors. These coefficients are scaled separately to the respective full scale values and subsequently reassembled to give the power prediction. The accuracy of this power prediction depends {\em inter alia} on the accuracy of the measured values and the scaling procedure. An inherent problem of this approach is, that it is virtually impossible to verify each single step, because of the complex nature of the underlying problem. In recent years the scaling of the open-water characteristics of propeller model tests attracted a renewed interest, fuelled by competitive tests, which became the norm due to requests of the customer. This paper will show the influence of different scaling procedures on the predicted power. The prediction is compared to the measured trials data and the quality of the prediction will be judged. The procedures examined are the standard ITTC~1978 procedure plus derivatives of it: the Meyne, the strip method and the βᵢ-method.

This paper reports the overall thermal performance of a cylindrical parabolic concentrating solar water heater (CPCSWH) with inserting nail type twisted tape (NTT) in the copper absorber tube for the nail twist pitch ratios 4.787, 6.914 and 9.042 respectively. The experiments are conducted for a constant volumetric water flow rate and during the time period 9:00 h to 15:00 h. The useful heat gain, hourly solar energy collected and hourly solar energy stored of this solar water heater are found higher for nail twist pitch ratio 4.787. The above said parameters are found to be a peak at noon and observed to follow the path of variation of solar intensity. At the starting of the experiment, the value of charging efficiency is observed to be maximum. Whereas the maximum value of instantaneous efficiency and overall thermal efficiency are observed at noon. The key finding is that the nail twist pitch ratio enhances the overall thermal performance of the CPCSWH.

In this paper, we discuss the most significant application opportunities and outline the challenges in performing a real-time and energy-efficient management of the distributed resources available at mobile devices and Internet-to-Data Center. We also present an energy-efficient adaptive scheduler for Vehicular Fog Computing (VFC) that operates at the edge of a vehicular network, connected to the served Vehicular Clients (VCs) through an Infrastructure-to-Vehicular (I2V) over multiple Foglets (Fls). The scheduler optimizes the energy by leveraging the heterogeneity of Fls, where the Fl provider shapes the system workload by maximizing the task admission rate over data transfer and computation. The presented scheduling algorithm demonstrates that the resulting adaptive scheduler allows scalable and distributed implementation.

Spin dependent quantum transport properties in twisted carbon nanotube and stretched carbon nanotube are calculated using density functional theory (DFT) and non-equilibrium green’s function (NEGF) formulation. Twisting and stretching have no effect on spin transport in CNTs at low bias voltages. However, at high bias voltages the effects are significant. Stretching restricts any spin-up current in antiparallel configuration (APC) which results in higher magneto resistance (MR). Twisting allows spin-up current almost equivalent to the pristine CNT case resulting in lower MR. High spin filtration is observed in PC and APC for pristine, stretched and twisted structures at all applied voltages. In APC, at low voltages spin filtration in stretched CNT is higher than in pristine and twisted ones with pristine giving higher spin filtration than twisted CNT.

In this paper, a novel permanent magnet-assisted synchronous reluctance machine (PMASynRM) with rare-earth PMs and ferrite magnets is proposed. The performance of PMASynRM is discussed with respected to the different magnet ratio of rare-earth PMs and ferrite magnets. Some characteristics including the flux density, output torque, cogging torque, output power, power factor, torque ripple, loss, efficiency, and demagnetization are calculated by 2-D finite element analysis (FEA). The analysis results show that the excellent performance can be obtained by using hybrid magnet of rare-earth PMs and ferrite magnets with the suitable magnet ratio, and provide some desirable cost-performance trade-off.

Food-borne transmission is a recognized route for many viruses associated with gastrointestinal, hepatic or neurological diseases. Therefore, it is essential to identify new bioactive compounds with broad-spectrum antiviral activity is needed to exploit innovative solutions against these hazards. Lately, antimicrobial peptides (AMPs) have been recognized as promising antiviral agents. Indeed, while the antibacterial and antifungal effects of these molecules have been widely reported, their use as potential antiviral agents has not yet been fully investigated. Herein, the antiviral activity of previously identified or newly designed AMPs, was evaluated against the non-enveloped RNA viruses, Hepatitis A virus (HAV), and Murine Norovirus (MNV), a surrogate for human Norovirus. Moreover, specific assays were performed to recognize at which stage of the viral infection cycle the peptides could function. Results showed that almost all peptides displayed virucidal effects with about 90% of infectivity reduction on HAV or MNV. However, the decapeptide RiLK1 demonstrated, together with its antibacterial and antifungal properties, a notable reduction in viral infection for both HAV and MNV, possibly through direct interaction with viral particles or inhibition of the viral bonding to the cell receptors. Hence, RiLK1 could represent a versatile ‘antimicrobial agent effective against various foodborne pathogens including viruses, bacteria, and fungi.

Matrices and their inverses allow accurate calculations to be produced quickly and compactly and can be used to control any process represented by a system of equations. Singular matrices require extensive workarounds (costing time and money) to solve these systems of equations because they have no inverse. Finding their inverse involves division by zero. Nevertheless, recently a new number set called semi-structured complex numbers was developed to enable division by zero in algebraic equations. The aim of this research was to demonstrate that the inverse of a singular matrix can be found using semi-structured complex numbers. This research reveals (1) Singular matrices and their inverses can be used to find a unique solution to a pair of simultaneous equations that appear to have infinitely many solutions or appear to have no solution; (2) Singular matrices map coordinates in projective space to coordinates in Euclidean space and their inverse maps coordinates in Euclidean space to coordinates in projective space; (3) the inverse of a singular matrix proves that parallel lines in Euclidean space do not intersect but in projective space intersect at a “point at infinity” and (4) collinear lines that intersect at infinitely many points in Euclidean space only intersect at one point in projective space.

In recent years, online review system attracts attention to assess seller-customer relations in the world of e-commerce. To address the quality concern of online review, especially incentivized ones, this study evaluates credibility and consistency based on reviews’ volume, length, and content to distinguish the impact of incentives on customer review behavior, improving review quality, and purchase decision-making. Software product reviews collected from software review websites, including Capterra, Software Advice, and GetApp undergo Exploratory Data Analysis (EDA) to reveal critical features such as cost, support, usability, and product features. The indirect impact of companies’ size, direct impact of users’ experience, and different impacts of changing situations during years on the incentive reviews’ volume are major findings of sentiment analysis. A/B testing results show a minimal to no impact of such reviews on purchasing decisions, highlighting discrepancies in credibility and consistency in volume, length, and content. Employing advanced techniques like Sentence-BERT (SBERT) and TF-IDF, the study explores semantic differences in reviews to improve recommendation systems for a more customized shopping experience. This approach seeks to establish a framework that discerns between review types and their effect on customer behavior. The findings contribute to developing more sophisticated and consistent e-commerce solutions, emphasizing the importance of authentic and reliable online reviews in influencing consumer choices.

This contribution deals with the assessment of air pollution caused by atmospheric aerosol particulate matter fraction PM10 and benzo[a]pyrene (BaP) in the urban agglomeration of Ostrava, located in the Czech Republic in Central Europe. The motivation for this research was the need to identify the sources of air pollution in the area, particularly in locations where the contribution of different sources to concentrations of pollutants of concern has not been elucidated yet. In this study, source apportionment in the vicinity of the industrial hot-spot was performed by statistically evaluating measured pollutant concentrations as a function of meteorological variables and using the Positive Matrix Factorization (PMF) receptor model. A significant methodological innovation and improvement over previous assessments was the higher monitoring resolution of benzo[a]pyrene, with samples collected at three-hour intervals instead of the standard 24-hour collection period. The key findings indicate that in the cold part of the year, secondary particles - specifically sulphates and ammonium nitrates - were responsible for the most significant portion of PM10 air pollution throughout the area of interest. The contribution of these particles ranged from one third to two fifths of the total concentration, except at the industrial site of Ostrava-Radvanice (TORE), where they accounted for approximately one fifth of the measured pollution concentration level. Emissions from individual household heating were identified as the main source of this type of pollution. With regards to benzo[a]pyrene air pollution, the study found that in the whole area of interest, except for the Ostrava-Radvanice site, it mainly originated from individual heating with coal (90%). In contrast, at the Ostrava-Radvanice site, two-thirds of the benzo[a]pyrene pollution came from the premises of Liberty Ostrava a.s., primarily from coke production, and less than one-third from local domestic heating. This study also determined the spatial extent of the occurrence of extremely high benzo[a]pyrene concentrations (above 5 ng/m3), which are estimated to affect nearly 10,000 inhabitants. The results confirm that the data from the TORE station are only representative of its immediate surroundings and are not applicable to the assessment of air quality and causes of air pollution in the whole city of Ostrava or the urban area of Ostrava-Radvanice as a whole. After years of research, these findings provide the Ministry of the Environment of the Czech Republic and the government with an accurate basis for implementing measures to address the identified pollution sources in the area of interest. The success of this study was made possible by the adoption of a more detailed sampling approach, which involved a resolution of 3 hours instead of 24 hours. This methodological improvement is a significant finding and will be useful for future source apportionment studies.

Replication protein A (RPA) is a heterotrimeric protein complex and the main single-stranded DNA (ssDNA) binding protein in eukaryotes. RPA has key functions in most of the DNA-associated metabolic pathways and DNA damage signalling. Its high affinity for ssDNA helps to stabilise ssDNA structures and prevents the DNA sequence from nuclease attacks. RPA consists of multiple DNA-binding domains which are oligonucleotide/oligosaccharide-binding (OB)-folds, responsible for DNA binding, and interactions with proteins. These RPA-ssDNA and RPA-protein interactions are crucial for DNA replication, DNA repair, DNA damage signalling, and the conversation of the genetic information of cells. Proteins such as ATR use RPA to locate to regions of DNA damage for DNA damage signalling. Recruitment of nucleases and DNA exchange factors to sites of double strand breaks are also an important RPA function to ensure effective DNA recombination to correct these DNA lesions. Due to its high affinity to ssDNA, RPA’s removal from ssDNA is of central importance to allow these metabolic pathway to proceed and processes to exchange RPA against downstream factors are established in all eukaryotes. These facetted and multi-layered functions of RPA will be discussed in detail in the review. RPA is also a major player in a variety of human diseases, which will be discussed.

Ewing sarcoma (EWS) is an aggressive pediatric malignancy of the bone and soft tissues in need of novel therapeutic options. To identify potential therapeutic targets, we focused on essential biological pathways that are upregulated by EWS-FLI1, the primary oncogenic driver of EWS, including mitotic proteins such as Aurora Kinase A (AURKA), Kinesin Family Member 15 (KIF15) and its binding partner, targeting protein for Xklp2 (TPX2). KIF15/TPX2 cooperates with KIF11, a key mitotic kinesin essential for mitotic spindle orientation. Given the lack of clinical grade KIF15/TPX2 inhibitors, we chose to target KIF11 (using SB-743921) in combination with AURKA (using VIC-1911), given phosphorylation of KIF15S1169 by Aurora A is required for its targeting to the spindle. In vitro, the drug combination demonstrated strong synergy (Bliss score ≥10) at nanomolar doses. Colony formation assay revealed significant reduction in plating efficiency (1-3%) and increased percent accumulation of cells in G2/M phase with the combination treatment (45-52%) upon cell-cycle analysis indicating mitotic arrest. In vivo studies in EWS xenograft mouse models showed significant tumor reduction and overall effectiveness: drug combination vs vehicle control (p≤0.01), SB-743921 (p≤0.01) and VIC-1911 (p≤0.05). Kaplan-Meier curves demonstrated superior overall survival with the combination compared to vehicle or monotherapy arms (p≤0.0001).

The rationalization and modeling of an electric discharge in a fluid require the knowledge of electron swarm parameters. In this work, transport coefficients of alcohols, including methanol, ethanol, propanol, and butanol are reported. The electron energy distribution function, mean energy, reduced mobility, and diffusion coefficient, are calculated using the two-term expansion of the electron Boltzmann equation in the frame of BOLSIG+ and the Monte Carlo collision code METHES. For such, experimental and theoretical values of the electron-alcohol collision cross-section, covering a range of electron impact energy from 1 eV to 1000 eV, are employed. A temperature of 300K, reduced fields E/N between $1-10^4$ Td (1Td = $10^{-21}~\rm Vm^2$), and Plasma density of $10^{19}~\rm m^{-3}$ were used in simulations. The calculated coefficients are compared with data available from previous studies.

A time interval only description necessarily needs its own independent definitions, without one moment time coordinates to it. In this paper derived are time interval only set properties, including commutation relations, addition, multiplication and derivatives. Time interval only set commutation relations, consistent with one moment time set properties, are introduced by defining correspondence relations for these sets. Time development and equilibrium within the time interval description depend on the well-known ‘mean velocity theorem’ and the time interval version of the Legendre transform. In contrast, usually applied is only the traditional vector and one moment time coordinate kinematic approach from Newton’s laws. The main results of this paper are correspondences and time interval only set commutation relations. All other properties are derived from these results, while for the time interval only set, different from the one moment time set the canonical property is not valid. The time interval only description can be applied assuming spherical symmetric star-source radiation propagation, with finite time intervals for realistic measurement events. From time development with (a-)symmetry of time intervals, and from Curie’s principle, change can be described with a set theoretic approach. Time interval only set properties include the time interval only version of Noether charges and structure constants. A time interval only description for wave propagation, including group-velocity, for zero and non-zero mass wave particles, relates to the properties of the time interval only set. A second result in terms of the time interval only description is propagation wave energy equivalence with gravitation energy, derived from time interval only set commutation relations. A time interval approach, however including one moment time description dependence, was introduced in earlier publications of this author. In part 1 investigated are the time interval only set and its properties, a forthcoming part 2 to application of the time interval only description to specific groups of stars as emission sources.

In recent, Chae found that, at weak gravitational acceleration g_N≲10⁻⁹ms⁻², the observed orbit of the wide binary stars is not accordant with current theory of binary star. Here, we present, this finding should be an observational evidence for that Newtonian theory of orbit perturbation is still valid in galactic scale.

: Ovarian cancer has a dismal prognosis. Standard treatment following surgery relies on platinum-based chemotherapy. However, sizeable percentages of patients are unresponsive. Identification of markers predicting response to chemotherapy might help select eligible patients while sparing unresponsive ones treatment-associated toxicity. Cancer/testis antigens (CTA) are expressed by healthy germ cells and malignant cells of diverse histological origin. This expression profile identifies them as attractive targets of cancer immunotherapies. We analyzed correlations between expression of MAGE-A10 and New York esophageal-1 cancer (NY-ESO-1) CTAs at protein level and effectiveness of platinum-based chemotherapy in patients with advanced-stage high-grade serous ovarian carcinoma (HGSOC). MAGE-A10 and NY-ESO-1 protein expression was analyzed by immunohistochemistry (IHC) in formalin-fixed, paraffin-embedded samples from 93 patients with advanced-stage HGSOC treated at our institutions between January 1996 and December 2013. Correlation between expression of these markers and response to platinum-based chemotherapy, evaluated according to RECIST 1.1 criteria, platinum sensitivity, measured as platinum free interval (PFI), progression free (PFS) and overall survival (OS) was explored. MAGE-A10 protein expression predicts unresponsiveness to platinum-based chemotherapy (p=0.005), poor platinum sensitivity (p<0.001), and poor PFS (p<0.001) and OS (p<0.001). Multiva-riate analysis identifies MAGE-A10 protein expression as independent predictor of poor platinum sensitivity (p=0.005) and shorter OS (p<0.001). Instead, no correlation was observed between NY-ESO-1 protein expression and response to platinum-based chemotherapy (p=0.832), platinum sensitivity (p= 0.168), PFS (p=0.126) and OS (p=0.335). MAGE-A10 protein expression reliably identifies advanced-stage HGSOC unresponsive to platinum-based chemotherapy. Targeted im-munotherapy could represent an important alternative therapeutic option in these cancers.

Polycyclic aromatic hydrocarbons (PAHs) have been reported to cause oxidative stress in metabolic processes. This study aimed to evaluate the relationship between exposure to PAHs, including benzo[a]pyrene (BaP) and 1-nitropyrene (1-NP), in the atmosphere and oxidative stress levels in the human body. This study included 44 Korean adults who lived in Cheongju, South Korea. Atmospheric BaP and 1-NP concentrations and urinary 6-hydroxy-1-nitropyrene (6-OHNP), N-acetyl-1-aminopyrene (1-NAAP), and 1-hydroxypyrene (1-OHP) concentrations were measured. The oxidative stress level was assessed by measuring urinary thiobarbituric acid reactive substances (TBARS) and 8-hydroxydeoxyguanosine (8-OHdG) concentrations. Urinary TBARS and 6-OHNP concentrations significantly differed between winter and summer. BaP exposure was significantly associated with urinary 8-OHdG concentrations in summer. However, atmospheric 1-NP did not show a significant correlation with oxidative stress marker concentrations. Urinary 1-NAAP concentration was a significant determinant for urinary 8-OHdG concentration in summer. Oxidative stress in the body increases in proportion to inhalation exposure to BaP, and more 8-OHdG is produced in the body as the amount of 1-NP, which is metabolized to 1-AP or 1-NAAP, increases.

Conducted within the scope of geochemical exploration in Eastern Thailand, this study aims to detect geochemical anomalies and potential mineral deposits. The objective was to interpret intricate spatial dispersion patterns and concentration levels of deposit pathfinder elements, specifically arsenic (As), copper (Cu), and zinc (Zn), using a comprehensive array of stream sediment geochemistry data. Methodologies involved integrating multifractal properties and traditional statistics, facilitated by the GeoDAS and ArcGIS platforms as instrumental analytical tools. In total, 5,376 stream sediment samples were collected and evaluated, leading to the development of an in-depth geochemical map. The results indicated distinct geological units marked by substantially elevated average values of the aforementioned elements. Identification of geochemical anomalies was achieved through the spatial distribution method and the subsequent application of the Spectrum-Area (S-A) multifractal model. An intriguing link was found between high As concentrations and gold deposits in the area, suggesting As as a viable pathfinder element for gold mineralization. The anomaly maps, generated from the stream sediment data, spotlighted potential zones of interest, offering valuable guidance for future mineral exploration and geological inquiries. Nonetheless, it is vital to recognize that the increased values noted in these maps may be influenced by regional geological factors, emphasizing the necessity for a diverse set of analytical methods for accurate interpretation. The study's significance lies in its pioneering use of the S-A multifractal model in geochemical data analysis. This innovative approach has deepened our comprehension of geochemical dispersion patterns and improved the precision of mineral exploration.

The visual appearance of humans derives significantly from our skin and hair color. While melanin from epidermal melanocytes protects our skin from the damaging effects of ultraviolet radiation, the biological value of pigmentation in the hair follicle, particularly in the scalp, is less clear. In this study, we explore the heterogeneity of pigment cells in the human scalp anagen hair follicle bulb, a site conventionally viewed to be focused solely on pigment production for transfer to the hair shaft. Using c-KIT/CD117 microbeads, we isolated bulbar c-KIT-positive and c-KIT-negative melanocytes. While both subpopulations expressed MITF, only the c-KIT-positive fraction expressed SOX10. We further localized bulbar melanocyte subpopulations (expressing c-KIT, SOX10, MITF, and DCT) that exhibited distinct/variable expression of downstream differentiation-associated melanosome markers (e.g., gp100 and Melan-A). Localization of a second ‘immature’ SOX10 negative melanocyte population, which was c-KIT/MITF double positive, was identified outside of the melanogenic zone in the most peripheral/proximal matrix. These studies describe an approach to purifying human scalp anagen hair bulb melanocytes, allowing us to identify unexpected levels of melanocyte heterogeneity. The function of the more immature melanocytes in this part of the hair follicle remains to be elucidated. Could they be in-transit migratory cells destined to synthesize mela-nin ultimately or could they contribute to the hair follicle in non-melanogenic ways.

This paper proposes an AI-based approach to overcome the limitations of the SHM system in measuring global stress with limited sensors. Feature elements are selected based on correlation analysis among finite elements and used as stress-measured points. An ANN is used to establish the solution relationship between the feature and correlation elements. The proposed method is applied to the connector structure of an offshore platform, and an optimal ANN is established to optimize accuracy by considering factors like the number of sensors, neural network framework, and convergence criteria. The accuracy of the ANN is verified through a real-scale model test, demonstrating 93.6% accuracy. This technology represents a significant advancement, enhancing the practicality of the structural health monitoring (SHM) system from “point monitoring" to “field monitoring".

Metachromatic leukodystrophy (MLD) is a hereditary neurodegenerative disease characterized by demye-lination and motor and cognitive impairment due to the deficiency of the lysosomal enzyme arylsulfatase A (ARSA) or the saposin B activator protein (SapB). Current treatments are limited; however, gene therapy using adeno-associated virus (AAV) vectors for ARSA delivery has shown promising results. The main challenges for MLD gene therapy include optimizing AAV dosage, selecting the most effective serotype, and determining the best route of administration for ARSA delivery into the central nervous system. This study aims to evaluate the safety and efficacy of AAV serotype 9 encoding ARSA (AAV9-ARSA) gene therapy when administered intrave-nously or intrathecally in minipigs, a large animal model with anatomical and physiological similarities to humans. By comparing these two administration methods, this study contributes to the understanding of how to improve the effectiveness of MLD gene therapy and offers valuable insights for future clinical applications.

This study explores the implications of merging two fundamentally different types of banks: Islamic and conventional banks. The research aims to provide insight into such a merger's unique opportunities and challenges and offer strategic guidance for future mergers. A balanced scorecard-based strategic analysis using Quantum Spherical Fuzzy Decision-Making Approach was used to develop the merged bank's short- and long-term strategic plans. The balanced scorecard included 12 key performance indicators (KPIs) in 4 groups, and the methodology also incorporated several questions to guide the analysis. The study results offer valuable insights into the potential opportunities and challenges of merging these two types of banks and strategic recommendations for stakeholders at all levels. The study is a valuable guideline for future mergers between similar or different types of banks. Overall, the findings suggest that a well-planned merger strategy is essential for avoiding challenges and maximizing the benefits of merging Islamic and conventional banks. By integrating the strengths of both types of banks, a merged entity could create a competitive advantage and potentially improve financial performance. However, this requires careful consideration of cultural differences, regulatory challenges, and other factors that could impact the merger's success.

In the presence of absorbing aerosol in the atmosphere a number of systematic errors of standard Ocean Color algorithms were noted, for example, negative values of remote sensing reflectance in the short-wavelength region at 412 nm and 443 nm. The main goal of this work is to develop an algorithm for additional correction of remote sensing reflectance level 2 satellite data, taking into account the presence of absorbing aerosol over the Black Sea, where a large number of dust transfers from the Sahara are observed annually. To implement the algorithm, an analytical and experimental evaluation of the interpolation function is carried out, taking into account the optical effects caused by the stratification of the absorbing aerosol. This algorithm is based on the constancy of the color index value, characteristic of the selected region. For the Black Sea the average value of CI(412/443) = 0.80±0.08, a small standard deviation indicates that the sample is slightly variable. Therefore, CI(412/443) = 0.80 will be further considered as the reference value of the color index for calculating new restored Rrs(λ).

Cancer stem cells remain a challenge to isolate and characterize because of their plastic phenotype. Using a microfluidic lab-on-a-chip based on ultra-high frequency dielectophoresis, we measured the electromagnetic signature of colorectal cancer cells and demonstrated that cancer stem cells show a distinct and lower electromagnetic signature than differentiated cells. The release of extracellular vesicles from tumor cells can drive tumor progression and metastasis development. As extracellular vesicles from cancer stem cells carry more aggressive content, we treated colorectal cancer cells with these vesicles to test whether the lab-on-a-chip can detect a change in phenotype. The electromagnetic signature of treated cells is modified in comparison to untreated cells and sometimes even when no biological change is observed. The lab-on-a-chip provides rapid and relevant result without prior labeling compared to conventional biological approaches. It could be useful in the clinic for early detection of cancer stem cells in the tumor mass and for monitoring the aggressive potential of extracellular vesicles in the bloodstream in order to adapt therapeutic management and prevent relapse.

Songorine (SON) is a diterpenoid alkaloid from Aconitum plants. Preparations of Aconitum roots have been employed in traditional oriental herbal medicine, however, their mechanisms of action are still unclear. Since GABA-receptors are possible brain targets of SON, we investigated which subtypes of GABA-receptors contribute to the effects of SON, and how SON affects anxiety-like trait behavior and psychomotor cognitive performance of rats. First, we investigated the effects of microiontophoretically applied SON alone and combined with GABA-receptor agents picrotoxin and saclofen on neuronal firing activity in various brain areas. Next, putative anxiolytic effects of SON (1.0-3.0 mg/kg) were tested against the GABA-receptor positive allosteric modulator refer-ence compound diazepam (1.0-5.0 mg/kg) in the elevated zero maze (EOM). Furthermore, basic cognitive effects were assessed in a rodent version of the psychomotor vigilance task (PVT). Local application of SON predominantly inhibited the firing activity of neurons. This inhibitory effect of SON was successfully blocked by GABA(A)-receptor antagonist picrotoxin but not by GABA(B)-receptor antagonist saclofen. Similar to GABA(A)-receptor positive allosteric modulator diazepam, SON increased the time spent by animals in the open quadrants of the EOM without any signs of adverse psychomotor and cognitive effects observed in the PVT. We showed that, under in vivo conditions SON acts as a potent GABA(A)-receptor agonist and effectively decreases anxiety without observable side effects. The present findings facilitate the deeper understanding of the mechanism of action and the widespread pharmacological use of diterpene alkaloids in various CNS indications.

In the present study, we studied the effect of apolipoprotein A-1 (APOA1) on the spatial and molecular characteristics of bone marrow adipocytes, using well-characterized ApoA1 knockout mice. APOA1 is a central regulator of high-density lipoprotein cholesterol (HDL-C) metabolism, and thus HDL; our recent work showed that deficiency of APOA1 increases bone marrow adiposity in mice. We found that ApoA1 deficient mice have greatly elevated adipocytes within their bone marrow compared to wild type counterparts. Morphologically, the increased adipocytes were similar to white adipocytes, and displayed proximal tibial-end localization. Marrow adipocytes from wild type mice were significantly fewer and did not display bone-end distribution pattern. The mRNA levels of the brown/beige adipocyte-specific markers Ucp1, Dio2, Pat2, Pgc1a, and the expression of leptin were greatly reduced in the ApoA1 knock-out in comparison to the wild-type mice. In the knock-out mice adiponectin was remarkably elevated. In keeping with the close ties of hematopoietic stem cells and marrow adipocytes, we found that the elevated adiposity in the ApoA1 knock out mice is associated with a significant reduction of the hematopoietic stem cells and common myeloid, but not common lymphoid, progenitors. Moreover, the “beiging”-related marker osteopontin and the angiogenic factor VEGF were also reduced in the ApoA1 knock-out mice, further supporting the notion that APOA1, and most probably HDL-C, regulate bone marrow microenvironment, favouring beige/brown adipocyte characteristics.

Organ-on-a-Chip (OoC) systems bring together cell biology, engineering, and material science for creating systems that recapitulate the in vivo microenvironment of tissues and organs. The versatility of OoC systems enables in vitro models for studying physiological processes, drug development, and testing in both academia and industry. This paper evaluates current platforms from the end-user perspective, elaborating on usability, complexity, and robustness. We surveyed 165 peers in over 30 countries and grouped the responses according to preliminary knowledge and the source of the OoC systems that are used. The survey clearly shows that current commercial OoC platforms provide a substantial level of robustness and usability - which is also indicated by an increasing adaptation of the pharmaceutical industry but a lack of complexity can challenge their use as a predictive platform. Self-made systems on the other hand are less robust and standardized but provide the opportunity to develop customized and more complex models which are often needed for human disease modeling. This review serves as a guide for researchers in the OoC field and encourages the development of next-generation OoCs.

Alzheimer’s and Parkinson's diseases (AD and PD) are amongst top of the prevalent neurodegenerative disease. One-third of PD patients are diagnosed with dementia, a pre-symptom of AD, but the underlying mechanism is elusive. Amyloid beta (Aβ) and α-synuclein are two of the most investigated proteins, whose pathological aggregation and spreading are crucial to the pathogenesis of AD and PD, respectively. Transcriptomic studies of the mammalian central nervous system shed light on gene expression profiles at molecular levels, regarding the complexity of neuronal morphologies and electrophysiological inputs/outputs. In the last decade, the booming of the single-cell RNA sequencing technique helped to understand gene expression patterns, alternative splicing, novel transcripts, and signal pathways in the nervous system at single-cell levels, providing insight for molecular taxonomy and mechanistic targets of the degenerative nervous system. Here, we re-visited the cell-cell transmission mechanisms of Aβ and α-synuclein in medi-ating disease propagation, and summarized recent single-cell transcriptome sequencing from different perspectives and discussed its understanding of neurodegenerative diseases.

The Betz limit sets a theoretical upper limit for the power production by turbines expressed as a maximum power coefficient of 16/27. Betz’s theory is accurate and it is based on the calculation of kinetic energy.

Pandemics caused by viruses have threatened lives of thousands of people. Viral infection is a complex and diverse process, and substantial studies have been complemented in understanding the biochemical and molecular interactions between viruses and hosts. However, the physical microenvironment where infections implement is often less carefully considered, and the role of mechanobiology in viral infection remains elusive. Mechanobiology focuses on sensation, transduction and response to intracellular and extracellular physical factors by tissues, cells and extracellular matrix. The intracellular cytoskeleton and mechanosensors have been proved to be extensively involved in virus life cycle. Furthermore, innovative methods in vivo and in vitro are being utilized to elucidate how extracellular factors including stiffness, forces and topography in regulating viral infection. Our current review covers how physical factors from different sources coordinate virus infection. We further discuss how this knowledge can be harnessed in future research on cross-fields of mechanobiology and virology.

The scale and accessibility of passive global surveillance have rapidly increased over time. This provides an opportunity to calibrate the performance of models, algorithms, and reflectance ratios between remote sensing devices. Here we test the sensitivity and specificity of Eucalypt chlorophyll-a reflectance ratio (ECARR) and Eucalypt chlorophyll-b reflectance ratio (ECBRR) to remotely identify eucalypt vegetation in Queensland, Australia. We compare reflectance ratio values from Sentinel-2 and Planet imagery across four sites of known vegetation composition. All imagery was transformed to reflectance values and Planet imagery was additionally scaled to harmonize across Planet Scenes. ECARR can identify eucalypt vegetation remotely with high sensitivity, but shows low specificity and is impacted by the density of the vegetation. ECBRR reflectance ratios show similar sensitivity and specificity when identifying eucalypt vegetation but with values an order of magnitude smaller than ECARR. We find that ECARR was better at identifying eucalypt vegetation in the Sentinel-2 imagery than Planet imagery. ECARR can serve as a general chlorophyll indicator but is not a specific index to identify Eucalyptus vegetation with certainty.

Cloud robotics is becoming an alternative to support advanced services of robots with low computing power as network technology advances. Recently, fog robotics has gained attention since the approach has merit relieving latency and security issues over the conventional cloud robotics. In this paper, a Function-as-a-Service based Fog Robotic (FaaS-FR) for cognitive robots is proposed. The model distributes the cognitive functions according to the computational power, latency and security with a public robot cloud and fog robot server. During the experiment with a Raspberry Pi as an edge, the proposed FaaS-FR model shows efficient and practical performance in the proper distribution of the computational work of the cognitive system.

Influenza virus imprinting is now understood to significantly the influence immune responses and clinical outcome of influenza virus infections that occur later in life. Due to the yearly cycling of influenza viruses, humans are imprinted with the circulating virus of their birth year to subsequently build a complex influenza virus immune history but very little is known about how the imprinting strain influences vaccine responses. To investigate the imprinted host immune responses to split-virion vaccination, we imprinted ferrets with a sublethal dose of the historical seasonal H1N1 strain A/USSR/90/1977. After a +60 day recovery period was given to build immune memory, ferrets were immunized and the challenge at Day 123. Samples were collected throughout the time course and immunological assays were performed to investigate recall mechanisms. The preimmune-vaccinated ferrets did not experience significant disease during challenge while naïve-vaccinated ferrets had severe disease. Hemagglutination inhibition assays showed preimmune ferrets had a more robust antibody response post vaccination, increased virus neutralization activity. Virus specific immunoglobulins were of predominantly the IgG isotype suggesting B cell maturity and plasticity at vaccination. These results are important and should be considered for vaccine design.

In this study, we actually want to explore the time-fractional Phi-four equation via two methods, the exp _a function method and the hyperbolic function method. We transform a fractional order dierential equation into an ordinary differential equation using a wave transformation and the fractional derivative in conformable form. Then, the resulting equation has successfully been explored for new explicit exact solutions. The procured solutions are simply showed the effectiveness and plainness of the projected methods.

Phylostratigraphic analysis is a way to look anew on phylogenetic data in the evolutionary aspect. It allows counting the evolutionary age based on the analysis of genes, their orthologs and finding the last common ancestor. We performed phylostratigraphic analysis of Arabidopsis thaliana genes associated with several types of abiotic stresses (heat, cold, water-related, light, osmotic, salt, and oxidative) determined by the Gene Ontology annotation. Comparison of the distributions of ages of genes associated with stresses of different type has shown the heat stress to involve older genes while the light stress – younger genes. At the same time, all types of stress are characterized by a significantly higher proportion of old genes (common to all eukaryotes) compared to the whole set of A.thaliana genes. This can be explained by the involvement of basic molecular processes in plant cells into the stress response. Reconstruction and graphical analysis of the gene network of the heat stress educed several clusters associated with different response functions. Some of these clusters contain only ancient genes. The results obtained show that the phylostratigraphic analysis reveals the fundamental features of the organization of gene networks and their evolution.

The purpose of this study was to evaluate the bioactivity and cell response of a well-characterized Nurse´s A-phase (7CaO•P2O5•2SiO2) ceramic and his effect compared to a control (tissue culture polystyrene-TCPS) on the adhesion, viability, proliferation and osteogenic differentiation of ahMSCs in vitro. Cell proliferation (Alamar Blue Assay), Alizarin Red-S (AR-s) staining, alkaline phosphatase (ALP) activity, osteocalcin (OCN) and collagen I (Col I) were evaluated. Also, field emission scanning electron microscopy (FESEM) images were acquired in order to visualise the cells and the topography of the material. The proliferation of cells growing in a direct contact with the material was slower at early stages of the study because of the new environmental conditions. However, the entire surface was colonized after 28 days of culture in growth medium (GM). Osteoblastic differentiation markers were significantly enhanced in cells growing on Nurse´s A phase ceramic and cultured with osteogenic medium (OM), probably due to the role of silica to stimulate the differentiation of ahMSCs. Moreover, calcium nodules were formed under the influence of ceramic material. Therefore, it is predicted that Nurse´s A-phase ceramic would present high biocompatibility and osteoinductive properties being a good candidate to be used as a biomaterial for bone tissue engineering.

The separation of sister chromatids during anaphase is the culmination of mitosis and one of the most strikingly beautiful examples of cellular movement. It consists of two distinct processes: Anaphase A, the movement of chromosomes toward spindle poles via shortening of the connecting fibers, and anaphase B, separation of the two poles from one another via spindle elongation. I focus here on anaphase A chromosome-to-pole movement. The chapter begins by summarizing classical observations of chromosome movements, which support the current understanding of anaphase mechanisms. Live cell fluorescence microscopy studies showed that poleward chromosome movement is associated with disassembly, or ‘melting’ of the kinetochore-attached microtubule fibers that link chromosomes to poles. Microtubule-marking techniques established that kinetochore-fiber disassembly often occurs through a ‘pac-man’ mechanism, where tubulin subunits are lost from kinetochore-attached plus ends and the kinetochore appears to consume its microtubule track as it moves poleward. In addition, kinetochore-fiber disassembly in many cells occurs partly through ‘flux’, where the microtubules flow continuously toward the poles and tubulin subunits are lost from minus ends. Molecular mechanistic models for how load-bearing attachments are maintained to disassembling microtubule ends, and how the forces are generated to drive pac-man and flux-based movements, are discussed.

Multi-junction solar cells comprised of stacked III-V semiconductor junctions represent the highest-efficiency photovoltaic technology, with recent demonstrations exceeding 47% efficiency . Optimizing the design and thickness of each junction is critical for maximizing performance . This work utilizes Silvaco TCAD tools to systematically optimize a 5-junction cell based on AlInP, AlGaInP, AlGaInAs, GaInP, GaAs, InGaAs, and Ge similar to recent record cells . The junction thicknesses are varied using a predictive profiler to sample the parameter space . For each combination, the spectral absorption and I-V characteristics are simulated to determine the efficiency . Statistical analysis identifies the optimal thickness set that maximizes performance to 26% under 1 sun illumination .

The advent of 5G technology represents a transformative leap in the realms of retail marketing and supply chain operations, offering unprecedented enhancements and posing unique challenges. This study explores the multifaceted impacts of 5G, focusing on its influence on customer experiences, operational efficiency, and supply chain management. The integration of 5G enables advanced technologies such as augmented reality (AR) and virtual reality (VR), significantly enhancing the interactivity and personalization of the shopping experience. Real-time data collection and analysis, facilitated by 5G, allow for more precise inventory management and optimized store operations, leading to improved customer satisfaction and reduced operational costs. In the supply chain domain, 5G technology offers enhanced visibility and control through real-time tracking and environmental monitoring, which improves logistics efficiency and product quality management. Despite these advancements, the adoption of 5G technology involves considerable challenges, including high infrastructure costs, data security concerns, and global disparities in technology deployment. Businesses must navigate these obstacles while leveraging the benefits of 5G to achieve competitive advantage. The study also highlights the role of 5G in integrating with other advanced technologies, such as artificial intelligence (AI) and blockchain, to drive further innovation. Additionally, 5G supports sustainability efforts by optimizing energy use and reducing waste. Overall, the successful implementation of 5G requires strategic investment and adaptability, but it holds the potential to revolutionize retail and supply chain operations, enhancing efficiency, customer engagement, and sustainability in a rapidly evolving digital landscape.

This study investigates the energy profile of a regional hospital in North America using an ASHRAE Level 2 Energy Audit. The audit aimed to assess the efficiency of existing systems, identify areas for improvement, and recommend cost-effective measures to reduce energy consumption and environmental impact. The analysis revealed a well-maintained heating system with efficient boilers. However, a critical concern emerged regarding operational risks due to the lack of redundancy in the cooling system. To address this vulnerability, the study recommends installing an air-cooled chiller for increased operational resilience. The economic feasibility of proposed improvements was evaluated, highlighting the balance between initial investment and long-term savings in energy costs and reduced greenhouse gas emissions. The findings contribute to the discourse on sustainable healthcare practices, emphasizing the importance of energy audits, strategic planning, and redundancy measures for optimized performance and environmental responsibility in hospitals.

The nutrient absorption and utilization efficiency in the roots of seedlings are beneficial for increasing crop yield. Creating marker assisted selection for wheat root traits can assist wheat breeders in choosing robust roots to maximize nutrient uptake. Exploring and identifying the effect of different nitrogen applications on RSA is of great significance for breeding nitrogen efficient wheat varieties. In this study, A total of 243 wheat varieties native to the Yellow and Huai Valley regions of China were utilized for genome-wide association studies (GWAS). Furthermore, a recombinant inbred line (RIL) population of 123 lines derived from the cross between Avocet and Chilero was utilized for linkage examination and confirmation of the hereditary loci distinguished by GWAS. Five RSA traits include the relative number of root tips (RNRT); relative total root length (RTRL); relative total root surface area (RTRS); relative total root volume (RTRV) and relative average root diameter (RARD) where evaluated under two N conditions—normal N (NN) supply and low N (LN)—to characterize the NUE of each accession. GWAS and linkage analysis were performed by integrating data from the wheat 660k single nucleotide polymorphism (SNP) chip and diversity arrays technology (DArT) to identify genetic loci associated with RSA. The results showed that based on the ratio of RSA related traits under two N supply conditions, a total of 598 SNP markers, which are significantly associated with RSA related traits, were detected at 160 genetic loci by GWAS. A total of 10 QTL loci related to RSA were dis-covered and identified by linkage mapping. In which, three significant RSA related Quantitative Trait Locus (QTL) were identified, namely qRtrl-3D, qRnrt-3D, and qRtrl-7D. The study has the potential to enhance the effectiveness of selecting root traits in wheat breeding programs, offering valuable insights into the genetic underpinnings of nitro-gen use efficiency (NUE) in wheat. This could lead to the creation of NUE wheat varieties by implementing focused breeding strategies.

Supplier Relationship Management (SRM) tools play a crucial role in enhancing efficiency and competitiveness within e-commerce supply chains. This qualitative research explores the effectiveness of SRM tools in optimizing procurement processes, mitigating risks, and fostering collaborative partnerships with suppliers. The study employs semi-structured interviews with key stakeholders in diverse e-commerce sectors to gather insights into the implementation and outcomes of SRM tools. Findings reveal that technological advancements, including AI, blockchain, and data analytics, facilitate real-time communication, decision-making, and supply chain visibility, thereby enabling organizations to achieve cost savings and operational efficiencies. Enhanced supplier relationships through SRM tools contribute to collaborative innovation, faster product development cycles, and improved customer satisfaction. However, challenges such as technological complexity, regulatory compliance, and supplier resistance necessitate strategic management and investment in cybersecurity and compliance frameworks. The research underscores the importance of executive sponsorship, stakeholder engagement, and continuous improvement in driving successful SRM implementations.

The Midwestern region of the United States has been experiencing periodic forage shortages due to frequent droughts, a growing livestock population, and reliance on traditional farming practices. This study evaluated the dry matter yield (DMY), forage nutritive value, water use efficiency (WUE), and economic viability of forage soybean [Glycine max (L.) Merr.] in a no-till winter wheat-based rainfed cropping system in the Midwest, USA. The research aimed to identify alternative summer forage crops that are drought-resilient, require lower inputs, mitigate seasonal gaps, and provide higher DMY and forage nutritive value compared to traditional forages. A four-year field experiment in a randomized complete block design with four replications assessed these parameters at various growth stages and planting dates. Results showed that forage soybean had a high DMY (~13 Mg ha-1), especially when optimally planted and harvested at the R3 stage. Forage nutritive value, including crude protein (CP), in vitro dry matter digestibility (IVDMD), and relative feed value (RFV), was highest at early vegetative stages (V2-V3), meeting livestock nutritional requirements. Forage soybean also demonstrated good WUE (21 kg ha-1 mm-1), making it suitable for water-limited regions. Economic analysis indicated substantial net profits ($322 per hectare), confirming its economic viability. The study concludes that forage soybean is a promising summer forage option for Midwest growers, offering high-quality forage, efficient water use, and economic benefits. Further research, particularly animal feeding trials, is recommended to validate its potential for widespread adoption in cropping systems.

Transport electrification is essential for reducing CO2 emissions, and technologies such as hybrid and range-extended electric vehicles will play a crucial transitional role. Such vehicles employ an internal combustion engine for on-board chemical energy conversion. The Wankel rotary engine should be an excellent candidate for this purpose, offering high power-to-weight ratio, simplicity, compactness, perfect balance, and low cost. Until recently, however, it has not been in production in the automotive market, due, in part, to relatively low combustion efficiency and high fuel consumption and unburnt hydrocarbon emissions, which can be traced to constraints on flame speed, an elongated combustion chamber, and relatively low compression ratios. This work uses large-eddy simulation to study the in-chamber flow in a peripherally ported 225cc Wankel rotary engine, providing insight into these limitations. Flow structures created during the intake phase play a key role in turbulence production but presence of the pinch point inherent to Wankel engine combustion chambers inhibits flame propagation. Two efficiency-enhancement technologies are introduced as disruptive solutions: (i) pre-chamber jet ignition and (ii) the two-stage rotary engine. These concepts overcome the traditional efficiency limitations and show that Wankel rotary engine design can be further enhanced for its role as a range extender in electrified vehicles.

Building energy demand impacts a myriad of interconnected economic, societal, and environmental aspects. As a result, Buildings Energy Models (BEM) play an important role in the process of urban design and planning. While previous studies have investigated the effects of building interventions on energy efficiency, their applicability may be limited due to the BEM’s high computational complexity. This limits their ability to systematically study important aspects of energy demand on a large scale. The development of Machine Learning Models (MLM) allows to design the required detailed analysis and solutions, while reducing the computational burden, making MLM attractive for urban designers. The capability of MLM to generalize well for multiple contexts (in our case, multiple buildings) is a crucial contributor to their applicability. However, the validation process in a wider context is often overlooked, therefore its generalization capabilities are not quantified. In this paper, we present a framework to train and validate a surrogate model derived from a physics-based BEM. Our method employs a Multiple Linear Regression model to predict Energy Use Intensity (EUI) for office buildings in Singapore using 36 input parameters (covariates), based on a training dataset of 23,000 samples. Model validation is performed by comparing the results of the Surrogate Model (SM) to a widely used BEM for a sample of 120 buildings. Our results indicate that the SM has an accuracy of NRMSE of 13%, NMBE of −3.56%, and R2 of 0.92, which suggests it can effectively and accurately predict building EUI. We also conduct a sensitivity analysis, which indicates that the parameters associated with internal loads and internal space usage are the most influential. Additionally, we present a reduced order model trained with only the 11 most influential parameters, which exhibits negligible loss in accuracy compared to the full SM while providing reduced complexity. Finally, we demonstrate an application of our SM to evaluate energy efficiency under uncertainty scenarios. The analytically derived results indicate a potential reduction of EUI of offices in Singapore from 227kWh/m2 to 99kWh/m2 by altering the building parameters that were identified as most influential.

Energy transition is one of the greatest challenges facing humanity today. All micro, small, medium and large enterprises in operation will have to face it, and some can al-ready boast the first successes in this regard. This paper focuses on the involvement of these smallest players in energy transition. Micro and small entities are the largest part of the economy, having a great influence on its development. Looking at the wide scale of their activities, these entities are distinguished by a specific owner-manager relationship. This means that the final decision-making is influenced by business goals, but also by the manager's approach, their awareness of changes, and personal and other factors. Based on a structured and standardized survey questionnaire, the research was carried out using the Computer-Assisted Telephone Interviewing technique between April and May 2022 among owners of micro and small enterprises operating in Poland. The survey showed that active engagement of micro and small enterprises in energy efficiency initiatives is related to their market success and financial health.

This study explores the advanced integration of Bi2Te3-based thermoelectric systems in Ocean Thermal Energy Conversion (OTEC) to optimize performance. OTEC, a promising renewable energy source, needs help in efficiency maximization. We address this by implementing Bi2Te3 thermoelectric generators (TEGs), known for their high thermoelectric efficiency at low-temperature differences. Our research encompasses a comprehensive simulation and analysis of these TEGs in OTEC systems, examining material properties, system design, and environmental impact. We present a novel approach to integrating these TEGs, optimizing their arrangement, and interfacing with the OTEC cycle to enhance overall efficiency. The study also investigates the durability and cost-effectiveness of Bi2Te3 TEGs in marine environments. Results demonstrate a significant improvement in energy conversion efficiency, highlighting the potential of Bi2Te3 TEGs in sustainable ocean energy exploitation. This work advances material science in renewable energy, providing valuable insights into the practical application of thermoelectric materials in large-scale energy systems. It paves the way for future research on material optimization and system integration, essential for developing efficient and sustainable OTEC systems.

While current video quality assessment research predominantly revolves around resolutions of 4K and beyond, targeted at Ultra High-Definition (UHD) displays, effective video quality for mobile video streaming remains primarily within the range of 480p to 1080p. In this study, we conducted a comparative analysis of the Quality of Experience (QoE) for widely implemented video codecs on mobile devices, specifically Advanced Video Coding (AVC), its successor High-Efficiency Video Coding (HEVC), and Google's VP9. Our choice of 720p video sequences from a newly developed database, all with identical bitrates, aimed to maintain a manageable subjective assessment duration, capped at 35-40 minutes. To mimic real-time network conditions, we generated stimuli by streaming original video clips over a controlled emulated setup, subjecting them to eight different packet loss scenarios. We evaluated the quality and structural similarity of the distorted video clips using objective metrics, including Video Quality Metric (VQM), Peak Signal-to-Noise Ratio (PSNR), Video Multi-Method Assessment Fusion (VMAF), and Multi-Scale Structural Similarity Index (MS-SSIM). Subsequently, we collected subjective ratings through a custom mobile application developed for Android devices. Our findings revealed that VMAF accurately represents the degradation in video quality compared to other metrics. Moreover, in most cases, HEVC exhibits an advantage over both AVC and VP9 under low packet loss scenarios. However, it is noteworthy that in our test cases, AVC outperformed HEVC and VP9 in scenarios with high packet loss, based on both subjective and objective assessments. Our observations further indicate that user preferences for the presented content contribute to video quality ratings, emphasizing the importance of additional factors that influence the perceived video quality of end-users.

In this paper, we propose a method for assessing the effectiveness of entropy features using several chaotic mappings. We anlyze fuzzy entropy (FuzzyEn) and neural network entropy (NNetEn) on four discrete mappings: the logistic map, the sine map, the Planck map, and the two-memristor-based map, with a base length time series of 300 elements. FuzzyEn is shown to have improved global efficiency (GEFMCC) in the classification task compared to NNetEn. At the same time, there are local areas of the time series dynamics in which the classification efficiency NNetEn is higher than FuzzyEn. The results of using horizontal visibility graphs (HVG) instead of the raw time series are also shown. GEFMCC decreases after HVG time series transformation, but there are local areas of the time series dynamics in which the classification efficiency increases after including the HVG. The scientific community can use the results to explore the efficiency of entropy-based classification of time series.

: Alluvial soils naturally possess abundant soil nutrients. Nevertheless, excessive nitrogen addition and inappropriate use of nitrogen fertilizers lead to conditions where soil nutrients become immo-bilized, ultimately reducing productivity. This study investigates the potential of natural nano-material zeolite which is important land resources to improve nutrient utilization efficiency and mitigate the harmful effects of excessive fertilizer application. Specifically, the research ex-plores the incorporation of clinoptilolite zeolite and processed sewage sludge blends, alongside reduced recommended nitrogen fertilizer doses, to evaluate their impact on soil quality and plant growth. A greenhouse experiment was conducted (three-year study), comprising eight treatments with varying proportions of zeolite and sewage sludge. The efficacy of these treatments in en-hancing soil carbon pools, nutrient indices, and plant growth responses was assessed. Results in-dicate that a combination of 50% recommended fertilizer dose, 4-6% zeolite, and 5-10% sewage sludge significantly improved multiple aspects of plant growth, including leaves, tillers, culms, and panicles, leading to increased straw and grain yields. The addition of 6% zeolite in conjunc-tion with sewage sludge positively influenced plant tillering capacity. Certain treatment combina-tions exhibited a greater impact on plant height at different growth stages. For example, the treatment with 75% recommended fertilizer dose, 4% zeolite, and 5% sewage sludge significantly affected plant height at 40 and 55 days after treatment. Additionally, the combination of 50% recommended fertilizer dose, 6% zeolite, and 10% sewage sludge promoted plant height, carbon levels, and various yield parameters in later stages. Principal component analysis effectively dis-tinguished treatments incorporating zeolite and sewage sludge based on plant responses. The combination of 6% zeolite and 10% sewage sludge, along with a 50% recommended fertilizer dose, positively influenced soil carbon fractions, nutrient levels, and the growth response of rice plants.

This article aims to assess the benefits of floor-slab insulation measures using extruded polystyrene (XPS) and polyisocyanurate (polyiso) insulation materials at various levels of insulation thicknesses for a detached residential building. The EnergyPlus simulation analysis was carried out within the seven energy zones (represented by eight locations) of South Africa in accordance with the South African national code for building energy efficiency (SANS10400-XA). The energy savings and payback periods due to use of the insulation over a lifecycle period of 50 years were assessed. Cape Town (zone 4) behaved differently from other locations and hardly benefitted from the application of floor-slab insulation measures. Generally, polyiso insulation performed better than XPS, for vertical gap insulation. For vertical gap insulation, lower insulation thicknesses required higher insulation depths to maximize energy savings. Similarly, lower insulation thicknesses required higher perimeter insulation widths to maximize energy savings, for the horizontal perimeter insulation method. The locations that benefitted most from vertical gap floor-slab insulation were Pretoria (zone2), Kimberley (zone6), Nelspruit (zone3), Fraserburg (zone7), Welkom (zone1), Mthatha (zone5), Ixopo (zone5H) and Cape Town (zone4) in that order. This order was almost similar with those for the horizontal perimeter floor-slab insulation and horizontal full floor-slab insulation methods.

Underwater wireless sensor networks (UWSNs) represent a specialized category of WSNs with versatile applications including acoustic monitoring, oil and gas exploration, and military surveillance. UWSNs face formidable challenges such as limited energy resources, extended propagation delays, and harsh conditions. Existing clustering and multi-hop routing protocols often unevenly distribute nodes geographically, causing network fragmentation and disproportionately draining the battery life of nodes near the sink due to higher data transmission demands. In this paper, we introduce an Energy-efficient Artificial Fish Swarm-based Clustering Protocol (EAFSCP), inspired by the collective behavior of fish swarms. EAFSCP is a decentralized clustering algorithm designed for acoustic monitoring in UWSNs. Its decentralized nature makes it particularly well-suited for large-scale UWSNs, where centralized algorithms may not be feasible. Through comprehensive comparisons with existing cluster-based routing protocols, our findings indicate that EAFSCP consistently outperforms them across multiple key performance metrics, including network lifetime, energy consumption, packet delivery ratio, packet loss rate, and throughput. According to the results, EAFSCP represents an effective clustering algorithm that enhances network performance, prolongs network lifespan by reducing energy consumption, promotes scalability, and provides valuable guidance for emergency response efforts.

This paper proposes a non-extensive entropy econometric technique to predict energy efficiency at province (NUT-2) level based on imperfect knowledge of the national overall efficiency in the sectors of industry, transport, households and services. The model is applied to the polish case. As acknowledged in recent literature, non-extensive entropy model should remain a valuable device for econometric modelling even in the case of low frequency series since outputs provided by the Gibbs-Shannon entropy approach correspond to the Tsallis entropy limiting case of the Gaussian law when the Tsallis q-parameter converges to unity. Therefore, we set up a q-Tsallis-Kullback-Leibler entropy criterion function with a priori consistency moment and model data constraints, including province energy intensity (known with uncertainty), regional climate differentiation and regular conditions. The model outputs continue to conform to empirical expectations. In spite of the close to unity q-Tsallis parameter, this Tsallis related approach reflects higher stability for parameter computation in comparison with the Shannon-Gibbs entropy econometrics technique. The proposed technique can be applied in different EU countries and elsewhere for example in the context of experimental official statistics.

Energy demand and consumption in recent times have witnessed a rapid proliferation influenced by technological developments, increased population and economic growth. This has fuelled research trends in the domain of energy management employing tri-generation systems such as the combined cooling, heating and power (CCHP) systems. Furthermore, the incorporation of renewable energy, especially solar energy, to complement the thermal input by fossil fuels has facilitated the effectiveness and sustainability of CCHP systems. This study proposes a new approach to improve the overall efficiency of CCHP systems and compute the optimal design parameters in order to assist decision makers to identify the best geometrical configuration. A multi-objective optimization formulation of a solar-assisted CCHP system was adopted to maximize the net power, the exergy efficiency and minimize the CO2 emission using the greywolf optimization technique. In addition, the effects of the decision variables on the objective functions were analysed. The proposed optimization approach yielded 100 set of Pareto optimal solutions which would serve as options to the decision maker to make a selection in order to improve the performance of a solar-assisted CCHP system. This study demonstrates that the proposed approach is potentially suitable for the optimization of a solar-assisted CCHP system.

The fishmeal production industry is essential for providing protein for animal feed in the aquaculture sector. However, the industry faces challenges related to energy consumption and environmental sustainability. This study evaluates the energy efficiency and environmental benefits of waste heat recovery (WHR) technologies in a fishmeal production plant in Vietnam. Data were collected from the plant between 2016 and 2022, and a specific energy consumption (SEC) indicator and a comprehensive methodology were utilized. Implementing an economizer as a WHR technology resulted in a 55.5% decrease in SEC compared to the state before installation. The enhanced energy efficiency also translated to reduced energy consumption per output unit. Moreover, the economizer contributed to annual energy savings of 4,537.57 GJ/year and cost savings of $26,474.49. Additionally, carbon dioxide (CO2) emissions associated with producing one ton of fishmeal decreased by 58.37%. These findings highlight the potential for WHR technologies to improve energy efficiency and reduce the environmental footprint of fishmeal production. The study's results provide valuable insights for practitioners and policymakers in promoting energy efficiency practices and reducing environmental impact in the industry.

One-Dimensional Solar Cell Capacitance Simulator (1D-SCAPS) and n-i-p planar configuration have been employed for the simulation of the caesium tin iodide (CsSnI₃)-based perovskite solar cell (PSC) with titanium (IV) oxide (TiO₂) and copper thiocyanate (CuSCN) as the electron and hole transport materials respectively. The results obtained for the initially modeled PSC compared well with similar devices in the literature but marred with high recombination rate. As such, the defect density in the CsSnI₃ absorber was varied from 10¹³ cm^-3 to 10¹⁷ cm^-3 and enriched with SnCl₂ (additive) and Br⁻(dopant) respectively. This strategy ensured a reduced concentration of Sn⁴⁺ vacancy (V_Sn) in the CsSnI₃ absorber with improved carrier lifetime and diffusion length beyond 0.05 ns and 1.1µm by a magnitude of the order of 10³ and 10² respectively for the enriched CsSnI₃ –based PSC. For the optimized PSC, we recorded V_OC=1.289 V, J_SC=32.60 mA.cm^-2, FF=83.56% and PCE=35.12%.

Photocatalytic degradation plays a crucial role in wastewater treatment, and the key to achieving high efficiency is to develop photocatalytic systems that possess excellent light absorption, carrier separation efficiency, and surface-active sites. Among various photocatalytic systems, S-type heterojunctions have shown remarkable potential for efficient degradation. This work delves into construction of S-type heterojunctions of ternary indium metal sulfide and bismuth ferrite nanofibers with introduction of sulfur vacancy defects and morphology modifications to enhance the photocatalytic degradation performance. Through the impregnation method, BiFeO₃/Zn₂S₄ heterojunction materials were synthesized and optimized30% BiFeO₃/Zn₂S₄ heterojunction exhibited superior photocatalytic performance with higher sulfur vacancy concentration than Zn₂S₄. The in-situ XPS results demonstrate that the electrons between Zn₂S₄ and BFO are transferred via S-Scheme, and after modification, Zn₂S₄ has a more favorable surface morphology for electron transport, and its flower-like structure interacts with the nanofibers of BFO, which has a further enhancement of the reaction efficiency for degrading pollutants. This exceptional material demonstrated a remarkable 99% degradation of Evans blue within 45 min and a significant 68% degradation of ciprofloxacin within 90 min. This work provides a feasible idea for developing photocatalysts to deal with the problem of polluted water resources under practical conditions.

The European Green Deal has set a concrete strategic plan to increase farm sustainability. At the same time, the current global challenges, due to climate change and fuels and commodity market crisis, combined with the Covid-19 pandemic and the ongoing war in Ukraine, comprise the need for quality food, but also the reduction of negative external effects of agricultural production, with fair remuneration for the farmers. In response, precision agriculture has great potential to contribute to the sustainable development. Precision agriculture is a farming management that provides a holistic system approach to managing the spatial and temporal crop and soil variability within a field to improve the farm’s performance and sustainability. However, farmers are still hesitant to adopt it. On these premises, the study aims to evaluate the impacts of precision agriculture technologies on farm profitability, agronomic and environmental management by farmers adopting (or not) these technologies, using the case study method. In detail, the work focuses on the period 2014-2022 for two farms that cultivate durum wheat in Central Italy. The results suggest that the implementation of precision technologies can guarantee economic and agri-environmental efficiency. Results could serve as a basis for developing a program to start training in farms as well as suggest policy strategies.

An area has been designated for demonstrating the utility of marine hydrokinetic turbines in Minas Passage, Bay of Fundy. Marine renewable energy may be useful for the transition from carbon-based energy sources but there is concern for the safety of fish that might encounter turbines. Acoustic receivers that detect signals from acoustically tagged fish that pass through the tidal demonstration area and detection efficiency of tag signals might be used to estimate the likelihood of fish encountering marine hydrokinetic turbines. The method requires that tagged fish passing through the development area will be reliably detected by a receiver array. The present research tests the reliability with which passing tags are detected by suspending tags beneath GPS-tracked drifters. Drifters carrying high residency Innovasea tags that transmitted every 2 seconds were usually detected by the receiver array even in fast currents during spring tides but pulse position modulation tags were inadequate. Sometimes very few high residency tag signals were detected when fast tidal currents swept a drifter through the receiver array, so increasing the transmission interval degrades performance at the tidal energy development area. High residency tags suspended close to the sea surface were slightly less likely to be detected if they passed by during calm conditions. Previously measured detection efficiencies were found to slightly overestimate the chances of a high residency tag carried by a drifter being detected as it passed by a receiver. This works elucidates the effectiveness with which acoustically tagged fish are detected in fast, highly turbulent tidal currents and informs the application of detection efficiency measurements to calculate the probability that fish encounter a marine hydrokinetic turbine.

The pressure on freshwater resources is leading to diminishing flows in some of the critical river systems across the globe and India is no exception and this is mainly because of water withdrawal for irrigation, which is often to the tune of 70% to 80% with some proportion for domestic and industrial use. While graduating from the concept of environmental flows and its assessment methodologies in India, the water-managers, the researchers and the conservationists are now moving towards answering the next question if the rivers are to be revived, then where will the water come from, especially in the case of over-allocated rivers, including the river Ganga. While the logical way is to look at the biggest user of water, i.e. irrigation, it remains to be seen whether the irrigation water savings will actually lead to enhancing flows in a river, complementing the efforts towards maintaining e-flows in rivers, or whether it will lead to more area under agriculture, bring changes in cropping patterns towards more water-intensive crops or result in something else. This is a growing debate across the globe, where India is no exception, and there has been a wide range of opinions in this regard. This paper discusses the process, findings and lessons from a joint initiative involving farmers, the Uttar Pradesh state Irrigation and Water Resources Department, Bijnor District Administration and a conservation organisation to enhance flows in a rivulet, called karula River, which is part of the Ganga river system.

Green innovation has become an important combination of high-quality economic growth and sustainable development of ecological environment. In this paper, the super-efficiency network SBM model is used to measure the two-stage green innovation efficiency of industrial science and technology R&amp;D and achievement transformation in 30 provinces and cities from 2009 to 2019, and exploratory Data Analysis (ESDA) and spatial econometric model are used to investigate the spatial-temporal evolution characteristics and influencing factors of green innovation efficiency. The results show that: firstly, the overall efficiency of industrial green innovation is low, and the efficiency of scientific research and development and achievement transformation has experienced three stages of "upward-declining-revitalized period". The low efficiency of achievement transformation is an important factor hiding the improvement of the efficiency of industrial green innovation. Secondly, The industrial green innovation efficiency gradually increases from northwest to southeast, forming a centralized "line" and "block" distribution. The high efficiency area is still concentrated in the eastern coastal region, and the balanced development trend is obvious in the central and western regions. Finally, openness has a positive impact on the two-stage green innovation efficiency; Industrial structure and government investment in science and technology have a positive impact on the efficiency of science and technology research and development, but have no significant effect on the efficiency of achievement transformation. Enterprise size has a positive effect on achievement transformation efficiency, but has no significant effect on R&amp;D efficiency. Environmental regulation has a positive impact on R&amp;D efficiency and a negative impact on achievement transformation efficiency.

This article describes in detail the numerical modeling of a CZTS (copper zinc tin sulfide) based kesterite solar cell. The Solar Cell Capacitance Simulator -one-dimension (SCAPS-1D) software was used to simulate MO/CZTS/CdS/ZnO/FTO structured solar cells. The parameters of different photovoltaic thin-film solar cells are estimated and analyzed using numerical modeling. The effects of various parameters on the performance of the photovoltaic cell and the conversion efficiency are discussed. Since the response of the solar cell is also contingent on its internal physical mechanism, J-V characteristic measures are insufficient to characterize the behavior of a device. Different features, as well as different potential conditions, must be considered for simulation, disregarding the belief in the modeling of a solar cell. With a conversion efficiency of 25.72%, a fill factor of 83.75%, a short-circuit current of 32.96436 mA/cm2 and an open-circuit voltage of 0.64V, promising optimized results have been achieved. The findings will be useful in determining the feasibility of fabricating high-efficiency CZTS-based photovoltaic cells. The efficiency of a CZTS-based experimental solar cell is also discussed. First, the effects of experimentally developed CZTS solar cells are simulated in the SCAPS-1D environment. The experimental results are then compared to the SCAPS-1D simulated results. The conversion efficiency of an optimized system increases after cell parameters are optimized. Using one-dimensional SCAPS-1D software, the effect of system parameters such as the thickness, acceptor and donor carrier concentration densities of absorber and electron transport layers, and the effect of temperature on the efficiency of CZTS-based photovoltaic cells is investigated. The proposed results will greatly assist engineers and researchers in determining the best method for optimizing solar cell efficiency, as well as in the development of efficient CZTS-based solar cells.

The use of swine manure as a source of plant nutrients is one alternative to synthetic fertilizers. However, conventional manure application with >90% water and a low C:N ratio results in soil C loss to the atmosphere. Our hypothesis was to use biochar as a manure nutrient stabilizer that would slowly release nutrients to plants upon biochar-swine manure mixture application to soil. The objectives were to evaluate the impact of biochar-treated swine manure on soil total C, N, and plant-available macro and micronutrients in greenhouse-cultivated corn (Zea mays L.) and soybean (Glycine max (L.) Merr.). Neutral pH red oak (RO), highly alkaline autothermal corn stover (HAP), and mild acidic Fe-treated autothermal corn stover (HAPE) biomass were pyrolyzed to prepare biochars. Each biochar was surface-applied to swine manure at a 1:4 (biochar wt/manure wt) ratio to generate mixtures of manure and respective biochars (MRO, MHAP, and MHAPE). Conventional manure (M) control and manure-biochar mixtures were then applied to the soil at a recommended rate. Corn and soybean were grown under these controls and treatments (S, M, MRO, MHAP, and MHAPE) to evaluate the manure-biochar impact on soil quality, plant biomass yield, and nutrient uptake. Soil OM significantly (<0.05) increased in all manure-biochar treatments; however, no change in soil pH or N was observed under any treatment. No difference in soil ammonium between treatments was identified. There was a significant decrease in soil M3-P and soil NO₃^- for all manure-biochar treatments compared to the conventional M. However, the plant biomass nutrient concentrations were not significantly different from control manure. Moreover, an increasing trend of N and decreasing trend of P in the plant under all biochar-manure treatments than the controls were noted. This observation suggests that the presence of biochar is capable of influencing the soil N and P in such a way as not to lose those nutrients at the early growth stages of the plant. In general, no statistical difference in corn or soybean biomass yield and plant nutrient uptake for N, P, and K was observed. Interestingly, manure-biochar application to soil significantly diluted the M3-extractable soil Cu and Zn concentrations. The results attribute that manure-biochar has the potential to be a better soil amendment than conventional manure application to the soil.

Classical enzyme kinetics are summarized and linked with modern discoveries here. The time course of sequential catalytic events by biological macromolecular enzyme is analyzed at the molecular level; the relationships between catalytic efficiency (turnover number), catalytic rate/velocity, the amount of time taken and physical/biochemical conditions of the system are discussed. This writing tries to connect the microscopic molecular behavior of enzyme to kinetic data obtained in experiment, and the hypothesis proposed here provide an interpretation to previous experimental observations and can be testified by future experiments.

Zinc-oxide (ZnO) nanostructures including nanorods are currently considered as a pioneer research of interest world-wide due to their excellent application potentials in various applied fields especially for the improvement of energy harvesting photovoltaic solar cells (PSC). We report on the growth and morphological properties of zinc-oxide (ZnO) nanorods grown on the surface of plain zinc (non-etched and chemically etched) plates by using a simple, economical, and environment-friendly technique. We apply hot water treatment (HWT) technique to grow the ZnO nanorods and varies the process parameters, such as temperature and the process time duration. The morphological, and elemental analysis confirm the agglomeration of multiple ZnO nanorods with its proper stoichiometry. The obtained nanostructures for different temperatures with different time duration showed the variation in uniformity, density, thickness and nanonorods size. The ZnO nanorods produced on the etched zinc surface were found thicker and uniform as compared to those grown on the non-etched zinc surface. This chemically etched Zinc plates preparation can be an easy solution to grow ZnO nanorods with high density and uniformity suitable for PSC applications such as to enhance the energy conversion efficiency of the photovoltaic (PV) solar cells towards the future sustainable green earth.

Growing popularity of buildings with integrated sub-systems, requires a review of methods to optimize the preheat of ventilation air. An integrated system permits using geothermal heat storage parallel to the direct outdoor air intake with additional treatment in the mechanical room as a part of building automatic control system. Earth Air Heat Exchanger (EAHX) has many advantages but also has many unanswered questions. Some of the drawbacks are: a possible entry of radon gas, high humidity in the shoulder seasons as well as the need for two different air intake sources with a choice that depends on the actual weather conditions. While in winter, the EAHX may be used continuously to ensure thermal comfort, in other seasons, its operation must be automatically controlled. To generate the missing information about the EAHX technology we have examined two nearly identical EAHX systems, one placed in ground next to the building and the other under the basement slab. In another project, we have reinforced the ground storage action by heat exchanger placed on the return pipes of the hydronic heating system. Effectively, the information provided in this paper, shows advantages of merging both these approaches while the EAHX could be placed under the house or near the basement foundation that is using an exterior basement insulation.

Growing popularity of smart and integrated buildings requires a review of methods to optimize the preheat of ventilation air. An integrated system permits using heat ex-changers located in the mechanical room or in the future even using an exterior wall as a heat exchanger. One may ask the question how does the earth-air heat exchanger (EAHX) technology fitts into this function. EAHX has many advantages but also has many unanswered questions. Some of the drawbacks are: a possible entry of radon gas, high humidity in the shoulder seasons as well as the need for two different air intake sources with a choice that depends on the actual weather conditions. While in winter, the EAHX may be used continuously to ensure thermal comfort, in other seasons, its operation must be automatically controlled. To generate the missing information about the EAHX technology we reviewed literature and examined two nearly identical EAHX systems, placed either in ground next to the building or under the basement slab. Effectively, the information provided in this paper, shows advantages of merging both these approaches while the EAHX shoud be placed under the house or near the basement foundation.

Ocean wave energy conversion as one of the renewable clean energy sources is attracting the research interests of many people. This review introduces different types of power take-off technology of wave energy converters. The main focus is the linear direct drive power take-off devices as they have the advantages for ocean wave energy conversion. The designs and optimizations of power take-off systems of ocean wave energy converters have been studied from reviewing the recently published literature. Also, the simple hydrodynamics of wave energy converters have been reviewed for design optimization of the wave energy converters at specific wave sites. The novel mechanical designs of the power take-off systems have been compared and investigated in order to increase the energy harvesting efficiency.

In this paper, modelling, simulation and verification of multi-agent manufacturing system with application of bio-inspired techniques are addressed. To this end, the new solution of abstract architecture for control and coordination decentralized systems - CODESA is suggested. Centralized architecture suffers from various problems, such as rigidity, scalability, low fault-tolerance or very limited flexibility, agility, energy efficiency and productivity. Prime is concrete application of CODESA in manufacturing domain. The undesirable characteristics of emergent behaviour are the problem to achieve optimization and impossibility to predict future states of the system. CODESA-Prime has been tested by simulations for automatic guided vehicle (AGV) systems guided by magnetic tape in Ella Software Platform.

Soil water balance (SWB) in woody crops is sometimes difficult to estimate with one-dimensional models because these crops do not completely cover the soil and usually have a deep root system, particularly when cropped under rainfed conditions in a Mediterranean climate. In this study, the actual crop evapotranspiration (ETc act) is estimated with the soil water balance model SIMDualKc which uses the dual-Kc approach (relating the fraction of soil cover with the crop coefficients) to improve the estimation of the water requirements of a rainfed vineyard, using data from a deep soil profile. The actual basal crop coefficient (Kcb act) obtained using the SIMDualKc model was compared with the Kcb act estimated using the A&amp;P approach, which is a simplified approach based on measurements of the fraction of ground cover and crop height. Spectral vegetation indices derived from Landsat-5 satellite data were used to determine the fraction of ground cover (fc VI) and thus, the density coefficient (Kd). The SIMDualKc model was calibrated using soil water content (SWC) measurements down to a depth of 1.85 meters, which significantly improved the conditions for using a SWB estimation model. The test of the model was performed using a different SWC dataset. A good agreement between simulated and field measured SWC was observed for both data sets along the crop season, with RMSE&lt;12.0 mm, NRMSE &lt;13%. The calibrated Kcb values were 0.15, 0.60 and 0.52 for the initial, mid-season, and end season, respectively. The ratio between actual (ETc act) and crop evapotranspiration (ETc) was quite low between veraison and maturity (mid-season), corresponding to 36%, indicating that the rainfall was not sufficient to satisfy the vineyards water requirements. Spectral vegetation indices used to compute fc VI were unable to fully track the plants’ conditions when water stress. However, ingestion of data from remote sensing showed promising results that could be used to support decisions making in irrigation scheduling. Further studies on the use of the A&amp;P approach using remote sensing data are required.

Atherosclerotic cardiovascular disease, a leading cause of morbidity and mortality worldwide, is a chronic inflammatory disease, linked to a state oxidative stress, with several well-identified culprits, of which low-density-lipoprotein cholesterol (LDL-C) and lipoprotein(a). No specific treatment is currently available to lower lipoprotein(a). It is, therefore, of paramount importance to identify nutritional factors that could lower lipoprotein(a). Growing evidence shows that although reducing saturated fatty acid (SFA) intake decreases LDL-C, it could increase lipoprotein(a). Optimal dietary recommendations may therefore differ depending on an in-dividual’s baseline lipoprotein(a) and LDL-C levels. Assessing the diet-induced true LDL-C response and net balance of these two atherogenic entities is difficult because LDL-C measurement is confounded by lipoprotein(a) cholesterol content. We have estimated, for the first time, the net atherogenic result of diet-induced variations of both LDL-C and lipoprotein(a), thanks to our new concept of LDLapoB risk equivalent=apoB+lp(a)x5 (in nmol/L). This is illustrated, via the rare case of a physician with very high lipoprotein(a) and hypobetalipoproteinemia. She experiences twice a considerable lipoprotein(a) increase (+32%, + 28mg/dL, + 67nmol/L) and higher LDLapoB risk equivalent (138mg/dL versus 123mg/dL) on a mediterranean diet, low in SFA. A reasonable SFA intake, despite causing marginal LDL-C increase, may be advisable in patients with high lipoprotein(a) who need personalized dietary recommendations.

The article presents the results of cyanide leaching of gold-containing concentrate using the trichlorocyanuric acid (TCCA) oxidizer. Gold-containing concentrate obtained from a gold tailings sample from a gold recovery factory (GRF) in one of the deposits of Kazakhstan that was not previously studied for concentrability. According to X-ray phase analysis and energy dispersive spectrometry (DSM) data, the main compounds in the tailings sample under study are: pyrite FeS2, quartz SiO2, calcite CaCO3, albite NaAlSi3O8, muscovite KAl2Si3AlO10(OH)8, dolomite CaMg(CO3)2, and oxidized iron compounds. Microscopic studies have established the presence of gold grains in free form, ranging in size from 0.9-10.2 mkm Au-ultrafine and fine gold. Obtaining a gold-containg concentrate with a gold content of 15.95 g / t is possible according to the enrichment scheme, which includes centrifugal separation, classification according to the fineness class -0.05 mm, additional grinding of hydrocyclone sands to a fineness of 90.0-95.0% of the class finer than 0.050 mm, and control centrifugal separation. Since pyrite in technogenic raw materials is the main gold-containing mineral, this paper presents studies on the oxidizability of pyrite with the TCCA oxidizer. The results of studies on the oxidation of pyrite using the TCCA oxidizer show that the products of its hydrolysis oxidize pyrite with the formation of various iron compounds on its surface. Pretreatment of gold-containing concentrate with oxidizer TCCA for 3 hours before the cyanidation process (20 hours) allows to increase the recovery of gold in the solution by 5.8 %.

Information geometry (IG) is a fascinating combination of differential geometry and statistics where a Riemannian manifold's structure is applied to a statistical model. It may find numerous fascinating uses in the domains of theoretical neurology, machine learning, complexity, and (quantum) information theory, among others. (IG) aims to provide a differential-geometric perspective on statistical geodesic models' structure. In this case, IG, KD, and J-divergence (JD) are used to define the manifold of the Generalised Brownian Motion (GBM). Consequently, the geodesic equations (GEs) are devised, and GB information matrix exponential (IME) is presented. Moreover, for first time ever, the necessary and sufficient mathematical requirement that characterizes the developability of Generalized Brownian Motion(GBM) manifold is devised. Also, a novel sufficient and necessary conditions which characterizes the regions where the surface describing GBM is minimal is determined. Also, it is shown that GBM has a non-zero 0-Gaussian and Ricci curvatures. Consequently, this advances the establishment of a unified GBM- Relativistic Info-Geometric based analysis.

This comprehensive review is devoted to an under-exploited family of phenolic compounds, the coumarins, and the most relevant strands in which they are involved in some spirit beverages – wine spirit, brandy, whiskey, sugar cane spirits (rum and cachaça) and grape marc spirit – with great importance worldwide in terms of production, trade and consumption. It gathers the key discoveries on the topic considering the production process of each spirit beverage, the related sources of coumarins (different kinds of wood used in the ageing stage) along with the factors that govern them and can influence the sensory properties of the aged beverages. An overview of the analytical methods available for their identification/quantification is also included, as well as the corresponding trends for the advancement of knowledge in this field. Moreover, the remarkable role of coumarins as nutraceuticals, their importance as chemical markers for authenticity purposes, and their relationship with food safety of these spirit beverages are also addressed, highlighting the current gaps and issues, and providing clues for future research.

One of the most widely available and extensively produced varieties of industrial hemp, which generates a substantial amount of consumer-increasing waste in the form of hemp cellulose. In this study, recycling with a compressed and high-speed method that combines crushing and alkali treatment effectively converts leftover hemp fiber into ultrafine powder. SEM (Scanning Electron Microscopy), AFM (Atomic Force Microscope), FTIR (Fourier-transform Infrared Spectroscopy), and XRD (X-ray Diffraction) examined the original morphology of hemp fiber treated with alkali, fiber heated to 200 ℃, and crushed powder. Particle size, crystallinity, fiber surface, and strength increased and decreased. It became apparent that fiber strength decreased and fiber roughness significantly increased after alkali treatment. Fiber increased significantly, and crystallinity decreased after crushing. It was simple and effective for converting the leftover hemp fiber into micron-sized powder. In about 3 to 5 minutes, approximately 1 kg of dry ultrafine powder with a particle size of 10.44 μm was produced. This production method will significantly enhance future industrial applications of waste hemp fiber.

Intestinal mucositis (IM) is a common adverse effect of chemotherapy, limiting its clinical application. Edible Chinese medicine, specifically Codonopsis pilosula-derived CP-A, with anti-inflammatory and gastrointestinal protective effects. The present work was to investigate CP-A's role in ameliorating IM and its mechanism using in vitro and rat models. Western blot, immunohistochemical (IHC) and real-time PCR (RT-PCR) analyses were used to assess protein expression related to the extracellular-regulated protein kinases (ERK)/myosin light chain kinase (MLCK)/myosin light chain 2 (MLC2) signaling pathway and tight junction proteins. Enzyme-linked immunosorbent assay (ELISA) was conducted to measure inflammatory factors, and 16S rRNA Amplicon Sequencing was employed for cecum content analysis. The results indicated that CP-A could restore body weight, food intake and histopathological changes in IM rats. Besides, abnormal MLCK activation induced by 5-fluorouracil (5-FU) was attenuated by CP-A via the ERK/MLCK/MLC2 pathway. CP-A treatment improved tight junction protein levels and reduced inflammatory factor expression. On the other hand, intestinal flora experiment demonstrated that CP-A intervention could increase the abundance of lactobacillus. In conclusion, CP-A mitigates 5-FU-induced IM by inhibiting the ERK/MLCK/MLC2 pathway, reducing the expression of inflammatory factors, improving the intestinal mucosal barrier and regulating intestinal flora. This study sheds light on CP-A's therapeutic potential in IM treatment, providing insights for future research.

We report on the occurrence of natural Magnesium Alumina Silicate Hydrate (M-(A)-S-H) cement at Feragen and Leka in eastern and western Trøndelag Norway, respectively. Both occurrences are located in the sub-arctic climate zone and form in glacial till and moraine material deposited on ultramafic rock during the Weichselian glaciation. Weathering of serpentinized peridotite dissolve brucite and result in a relative high pH alkaline fluid that subsequently reacts with the felsic minerals of the till (quartz, plagioclase, K-feldspar) to form a cement consisting of an amorphous material or a mixture of nanocrystalline Mg-rich phyllosilicates, including illite. The presence of plagioclase in the till results in the enrichment of alumina in the cement, i.e., forms M-A-S-H instead of the M-S-H cement. Dissolution of quartz results in numerous etch-pits and negative quartz crystals filled with M-A-S-H cement. Where the quartz dissolution is faster that the cement precipitation, a honeycomb-like texture is formed. Compositionally the cemented till (tillite) contains more MgO and has a higher loss of ignition than the till, suggesting that the cement is formed by a MgO fluid that previously reacted with the peridotite. The M-(A)-S-H cemented till represent a new type of duricrust, coined magsilcrete. The study of natural Mg-cement provides information on peridotites as a Mg-source for Mg-cement and as a feedstock for CO2 sequestration.