This study presents structural analysis and optimization for the lightweight design of a buoyant rotor-type permanent magnet (BRPM) generator, which was first presented in Bang (2010), and compares its structural performances to a conventional generator with a spoke arm-type rotor and stator. The main benefit of a BRPM is that it can be realized as a bearing-less drive system, free from the mechanical failure of rotor bearings, by using a buoyant rotor. Also, the deformation of a generator by blade vibration can be effectively suppressed using joint couplings between the blades and the rotor. For the design optimization, the objective is set as the mass of the rotor and the stator, and the maximum deformation of the airgap clearance between the rotor and the stator by external forces is constrained below 10% of the gap width. The commercial software Optistruct is used for the analysis and optimization. In this investigation, the analysis and optimization are conducted for a 10 MW wind turbine generator. However, the proposed methods can be extended to larger generator designs without requiring considerable modification. The mass of the opti-mized 10MW BRPM generator is 160.7 tons (19.3 tons for the rotor and 141.4 tons for the stator) while that of an optimized conventional spoke arm-type generator is obtained as 325.6 tons.

Alunogen, Al2(SO4)3·17H2O, occurs as an efflorescent in acid mine drainage, low-temperature fumarolic or pseudofumarolic (at coal fires) terrestrial environments. It is considered as one of the main Al-sulfates of Martian soils demanding comprehensive crystal chemical data of natural terrestrial samples. However, structural studies of natural alunogen were carried out in 1970s without localization of H atoms and have not previously been performed for samples from geothermal fields, despite the fact that these environments are considered as proxies of the Martian conditions. The studied alunogen sample comes from Verkhne-Koshelevsky geothermal field (Koshelev volcano, Kamchatka, Russia). Its chemical formula is somewhat dehydrated, Al2(SO4)3×15.8 H2O. The crystal structure was solved and refined to R1 = 0.068 based on 5112 unique observed reflections with I > 2σ(I). Alunogen crystalizes in P-1 space group, a = 7.4194(3), b = 26.9763(9), c = 6.0549(2) Å, α = 90.043(3), β = 97.703(3), γ = 91.673(3) °, V = 1200.41(7) Å3, Z = 2. The crystal structure consists of isolated SO4 tetrahedra, Al(H2O)6 octahedra and H2O molecules connected by hydrogen bonds. The structure refinement includes Al, S and O positions that are similar to previous structure determinations and thirty-four H positions localized for the natural sample first. The study also shows the absence of isomorphic substitutions in the composition of alunogen despite the iron-enriched environment of mineral crystallization. The variability of the alunogen crystal structure is reflected in the number of “zeolite” H2O molecules and their splitting. The structure complexity of alunogen and its modifications ranges from 333-346 bits/cell for models with non-localized H atoms to 783-828 bits/cell for models with localized H atoms. The higher values correspond to higher hydration state of alunogen.

The 2-oxoglutarate dehydrogenase complex (OGDHc) is a key enzyme in the TCA cycle and represents one of the major regulators of mitochondrial metabolism through NADH and reactive oxygen species levels. The OGDHc impacts cell metabolic and cell signaling pathways through the coupling of 2-oxoglutarate metabolism to gene transcription related to tumor cell proliferation and aging. DHTKD1 is a gene encoding 2-oxoadipate dehydrogenase (E1a), which functions in the L-lysine degradation pathway. The potentially damaging variants in DHTKD1 have been associated to the (neuro) pathogenesis of several diseases. Evidence was obtained for the formation of a hybrid complex between the OGDHc and E1a, suggesting a potential cross talk between the two metabolic pathways and raising fundamental questions about their assembly. Here we reviewed the recent findings and advances in understanding of protein-protein interactions in OGDHc and 2-oxoadipate dehydrogenase complex (OADHc), an understanding that will create a scaffold to help design approaches to mitigate the effects of diseases associated with dysfunction of the TCA cycle or lysine degradation. A combination of biochemical, biophysical and structural approaches such as chemical cross-linking MS and cryo-EM appears particularly promising to provide vital information for the assembly of 2-oxo acid dehydrogenase complexes, their function and regulation.

COVID-19 is characterized by an unprecedented abrupt increase in the viral transmission rate (SARS-CoV-2) relative to its pandemic evolutionary ancestor, SARS-CoV (2003). The complex molecular cascade of events related to the viral pathogenicity is triggered by the Spike protein upon interacting with the ACE2 receptor on human lung cells through its receptor binding domain (RBD_Spike). One potential therapeutic strategy to combat COVID-19 could thus be limiting the infection by blocking this key interaction. In this current study, we adopt a protein design approach to predict and propose non-virulent structural mimics of the RBD_Spike which can potentially serve as its competitive inhibitors in binding to ACE2. The RBD_Spike is an independently foldable protein domain, resilient to conformational changes upon mutations and therefore an attractive target for strategic re-design. Interestingly, in spite of displaying an optimal shape fit between their interacting surfaces (attributed to a consequently high mutual affinity), the RBD_Spike–ACE2 interaction appears to have a quasi-stable character due to a poor electrostatic match at their interface. Structural analyses of homologous protein complexes reveal that the ACE2 binding site of RBD_Spike has an unusually high degree of solvent-exposed hydrophobic residues, attributed to key evolutionary changes, making it inherently ‘reaction-prone’. The designed mimics aimed to block the viral entry by occupying the available binding sites on ACE2, are tested to have signatures of stable high-affinity binding with ACE2 (cross-validated by appropriate free energy estimates), overriding the native quasi-stable feature. The results show the apt of directly adapting natural examples in rational protein design, wherein, homology-based threading coupled with strategic ‘hydrophobic ↔ polar’ mutations serve as a potential breakthrough.

Substrate binding proteins (SBP) bind to specific ligands in the periplasmic region and bind to membrane proteins to participate in transport or signal transduction. Typical SBPs consist of two α/β domains and recognize the substrate by hinge motion between two domains. Conversely, short length Rhodothermus marinus SBP (named as RmSBP) exists around the methyl-accepting chemotaxis protein. We previously determined the crystal structure of RmSBP consisting of a single α/β domain, but the substrate recognition mechanism is still unclear. To better understand the short length RmSBP, we performed comparative structure analysis, computational substrate docking, and X-ray crystallographic study. RmSBP shares a high level of similarity in α/β domain with other SBP proteins, but it has a distinct topology in the C-term region. The substrate binding model suggested that conformational change in the peripheral region of RmSBP was required to recognize the substrate. We determined the crystal structures of RmSBP at pH 5.5, 6.0, and 7.5. RmSBP showed structural flexibility of the β1-α2 loop, β5-β6 loop, and extended C-term domain based on the electron density map and temperature B-factor analysis. These results provide information that will further the understanding of the function of the short length SBP.

In a world where conventional sources of energy are fast depleting, the quest for alternative energy sources may hold the key for the survival of humanity. In the present work, emphasis has been given to the idea of producing energy from perovskite based solar cells. In order to bring this idea into fruition, a unique and novel nano structured perovskite material n-propyl ammonium lead chloride (C₃H₇NH₃⁺PbCl₃⁻) was prepared through a unique co-precipitation route using n-propyl amine (n-C₃H₇NH₂) and hydrochloric acid as the starting precursors with aqueous solution of Pb(CH₃COO)₂3H₂O. Finally acetic acid was added to the solution and this solution was allowed to concentrate and then gradually cooled down to room temperature. After math, the synthesized material was spin-coated on TiO₂ film to fabricate the solar cell. The device was then undergone systematic analysis using XRD, SEM, UV and Photo Conversion to get a transparent idea regarding its structural, electrical and optical properties. When experimentally applied, this perovskite-based solar cell has shown energy conversion efficiency (η) of around 6.01 % which is noticeably good. Thus it can be concluded that this material is promising for fabrication of vastly efficient solar cells. This technology can be tried in large scale as an alternative of conventional energy in the near future.

The aging of the global population has increased the prevalence of neurodegenerative conditions. Bacopa monnieri (BM), an herb with active compounds, such as bacosides A and B, betulinic acid, loliolide, asiatic acid, and quercetin, demonstrates the potential for brain health. Limited research has been conducted on the therapeutic applications of BM in neurodegenerative conditions. This systematic review aims to project BM's beneficial role in brain disorders. BM has anti-apoptotic and antioxidant actions and can repair damaged neurons, stimulate kinase activity, restore synaptic function, improve nerve transmission, and increase neuroprotection. The included twenty-two clinical trials demonstrated that BM can reduce Nuclear Factor-κB phosphorylation, improve emotional function, cognitive functions, anhedonia, hyperactivity, sleep routine, depression, attention deficit, learning problems, memory retention, impulsivity, and psychiatric problems. Moreover, BM can reduce the levels of pro-inflammatory biomarkers and oxidative stress. Here, we highlight that BM provides notable therapeutic benefits and can serve as a complementary approach for the care of patients with neurodegenerative conditions associated with brain disorders. This review adds to the growing interest in natural products and their potential therapeutic applications by improving our understanding of the mechanisms underlying cognitive function and neurodegeneration and informing the development of new therapeutic strategies for neurodegenerative diseases.

A novel manufacturing process is presented for producing Nano powders and thin films of CuCoO₂ (CCO) material. This process utilizes three cost-effective synthesis methods: hydrothermal, sol-gel, and solid-state reactions. The resulting delafossite CuCoO₂ samples were deposited onto transparent substrates through spray pyrolysis, forming innovative thin films with a Nano crystal powder structure. Prior to the transformation into thin films, CuCoO₂ powder was first produced using a low-cost approach. The precursors for both powders and thin films were deposited onto glass surfaces using a spray pyrolysis process, and their characteristics were examined through X-ray diffraction, scanning electron microscopy, HR-TEM, UV-visible, and Electrochemical impedance spectroscopy (EIS) analyses was conducted to determine the conductivity in transversal direction of this groundbreaking material for solar cell applications. On the other hand, the sheet resistance of the samples was investigated using the four probe-method to obtain the sheet resistivity and them calculate the in plane conductivity of the samples. We also investigated the aging characteristics of different precursors with varying durations. The functional properties of CuCoO2 samples were explored by studying chelating agent and precursor solution aging periods. Resuming, this study thoroughly discusses the synthesis of delafossite powders and their conversion into thin films, which hold potential as hole transport layers in transparent optoelectronic devices.

With the deterioration of the bridge performance and ever-increasing amount of traffic, the bridge safety is becoming a concern for engineering community. A method that can assess the bridge's condition in real-time is urgently needed. The main factors that hinder the bridge condition assessment are the uncertain operational environments. A new moving principal component analysis (MPCA) based method is developed for structural damage detection of bridges in operational environments in this paper. Two main operational environmental factors: the environmental temperature and traffic loads, are studied in the assessment process to verify the robustness and practicality of the proposed method. The numerical and experimental results show that the proposed method is effective and accurate to assess the bridge condition in operational environments.

CagY is the largest and most complex protein from Helicobacter pylori's type IV secretion system (T4SS) and may participate in the modulation of gastric tissue inflammation. A three-dimensional structure has been reported for only two segments of the protein. To build a more complete model, particularly the region that spans between the outer membrane (OM) and the inner membrane (IM), we employed different approaches, including homology modeling, ab initio, and deep learning techniques. For the long-middle repeat region (MRR), modeling was performed using deep learning techniques and Molecular Dynamics. The modeled segments were assembled into a chain of 1595 aa, and a 14-chain CagY multimer structure was composed by structural alignment. The final multimer structure correlated with previously published struc-tures and allows to show how the multimer may form the T4SS channel through which CagA and other molecules are translocated to gastric epithelial cells. The model further confirmed that MRR, the most polymorphic and complex region of CagY, presents numerous cysteine residues forming disulfide bonds that stabilize the protein and suggest this domain probably functions as a contractile region that may play an essential role in the modulatory activity of CagY on tissue inflammation.

The morphology of virgin reactor powder (RP) of high-density polyethylene HDPE with MW = 160,000 g/mol was investigated with the help of DSC, SEM, SAXS and WAXS methods. The morphological SEM analysis showed, that the main morphological units of RP are macro- and micro-shish kebab structures with significantly different geometric dimensions, as well as individual lamellae of folded chain crystals. Quantitative analysis of an asymmetric SAXS reflection made it possible to reveal the presence of several periodic morphoses in the RP with long periods from 20 nm to 60 nm and to correlate them with the observed powder morphology. According to the DSC crystallinity data, the thickness of the lamellae in each long period was estimated. Their surface energy was calculated in the framework of the Gibbs-Thompson theory. The presence of regular and irregular folds on the surface of the different shish-kebab lamellae is discussed. The percentage of identified morphoses in the RP was calculated. It has been suggested that the specific structure of HDPE RP is due to the peculiarity of polymer crystallization during suspension synthesis in a quasi-stationary regime, in which local overheating and inhomogeneous distribution of shear stresses in a chemical reactor are possible.

This study presents a novel method based in ray tracing for analyzing wave propagation in composites, specifically tailored for Structural Health Monitoring applications. The method offers distinct advantages over the commonly used Finite Element Method mainly in computational resource utilization, that has become a limiting factor for this kind of analyses. The ray tracing method is evaluated against a number of example cases representing structural details such as thickness changes, stringers or simulated damages and it highlights the significance of ray tracing to study wave propagation under these conditions and how it can serve as a valuable tool for structural health monitoring.

The widespread use of renewable energy sources has considerably expanded distributed generation. An unbalanced load on distribution cables may also result from the recent increase in novel appliances and electric vehicles, the reverse power flow may create short-term overloads. These transient overloads increase the temperature for a short time beyond the limit, which causes degradation. However, the temperature distribution on the cable is not even. Therefore, the cable components are not degraded evenly and similarly. This publication describes the change in electrical properties of low-voltage cables caused by short-term cyclic artificial ageing to track the impact of these brief temperature rises. This study examines how cable structure affects the dielectric characteristics of cable specimens. Four cable samples, each measuring 50 cm in length (SZAMKAM 0.6/1 kV 16 mm2× 4 manufactured by Prysmian MKM Kft, Hungary) put through an accelerated ageing test in a temperature-controlled oven after changing their structures by removing their layers. Three rounds, each of six hours, accelerated thermal ageing were applied. After each round of ageing, the dielectric parameter tanδ and capacitance were measured by Dirana Dielectric Response Analyzer in the laboratory at room temperature 24±0.5∘C. Furthermore, the polarization and depolarization currents were also studied. The results show that changing the cable structure impacts the dielectric parameters, especially the effect of belting layer is significant. From point of view of aging the PVC belting layer protects the diffusion of plasticizers of inner structure.

The number of applications for nanobodies is steadily expanding, positioning these molecules as fast-growing biologic products in the biotechnology market. Several of their applications require protein engineering, which in turn would greatly benefit from having a reliable structural model of the nanobody of interest. However, as with antibodies, structural modeling of nanobodies is still a challenge. With the rise of artificial intelligence (AI), several methods have been developed in recent years that attempt to solve the problem of protein modeling. In this study, we have compared the performance in nanobody modeling of several state-of-the-art AI-based programs, either designed for general protein modeling, such as AlphaFold2, OmegaFold, ESMFold and Yang-Server, or specifically designed for antibody modeling, such as IgFold, and Nanonet. While all these programs performed rather well in constructing the nanobody framework and CDRs 1 and 2, modeling of CDR3 sill represents a big challenge. Interestingly, tailoring an AI method for antibody modeling does not necessarily translate into better results for nanobodies.

Most neurodegenerative diseases have the characteristics of proteinopathies, i.e. they cause lesions to appear in vulnerable regions of the nervous system, corresponding to protein aggregates that progressively spread through the neuronal network as the symptoms progress. Alzheimer's disease is one of these proteinopathies. It is characterized by two lesions, neurofibrillary tangles (NFTs) and senile plaques, formed essentially of amyloid peptides (Aβ). A combination of factors ranging from genetic mutations to age-related changes in the cellular context converge in this disease to accelerate Aβ deposition. Over the last two decades, numerous studies have attempted to elucidate how structural determinants of its precursor (APP) modify Aβ production, and to understand the processes leading to the formation of different Aβ aggregates; e.g. fibrils and oligomers. The synthesis proposed in this review indicates that the same motifs can control APP function and Aβ production essentially by regulating membrane dimerization, and subsequently Aβ aggregation processes. The distinct properties of these motifs and the cellular context regulate the APP conformation to trigger the transition to the amyloid pathology. This concept can be transposed to the study of other proteinopathies, providing a framework for improving our understanding of these mechanisms that devastate neuronal functions.

Background: Recent work has investigated significant force transmission between the compo-nents of myofascial chains. Misalignments in the body due to fascial thickening and shortening can therefore lead to complex compensatory patterns. For the treatment of such nonlinear cause-effect pathology, a comprehensive neuro-musculoskeletal therapy such as the Rolf Meth-od of Structural Integration (SI) could be targeted. Methods: A total of 727 subjects were retro-spectively screened from the medical records of an SI practice over a 23-year period. 383 subjects who had completed 10 basic SI sessions met eligibility criteria and were assessed for active range of motion (AROM) of the shoulder and hip before and after SI treatment. Results: Shoulder flex-ion, external and internal rotation, and hip flexion improved significantly (all p < 0.0001) after 10 SI sessions. Left shoulder flexion and external rotation of both shoulders increased more in men than in women (p < 0.0001), but were not affected by age. Conclusions: SI intervention produces multiple changes in the components of myofascial chains that could help maintain upright pos-ture in humans and reduce inadequate compensatory patterns. SI affects differently the outcome of some AROM parameters in women and men.

The main objective of this study is to apply structural equation modeling with partial least squares and based on covariance to assess the satisfaction of residential electricity consumers. The methodology used compares the results of both structural equation models to indicate the model that best fits the problem of measuring the satisfaction of residential consumers of electricity concessionaires and licensees. The sample used in the survey contained questionnaire responses from 86.175 individuals considering the period from 2014 to 2018. The constructs evaluated were satisfaction, quality, value, loyalty, and trust. Confidence interval analysis shows that all weights are significant, demonstrating the importance of all the indicators that represent the constructs. The trust, quality, and value constructs can explain 74.4% of the variability of the satisfaction construct, so the explanatory capacity of this relationship is considered substantial. Finally, the evaluation of the performance of the service provided by the electric energy concessionaires/licensees, measured by customer satisfaction, allows for the continuous improvement of services and meeting, even if minimally, the expectations of its consumers.

A quantitative method is proposed to determine of Stone-Wales defects for carbon nanostructures with sp2 hybridization of carbon atoms. The technique is based on the diene synthesis reaction (Diels-Alder reaction). The proposed method was used to determine Stone-Wales defects in the few-layer graphene (FLG) nanostructures synthesized by the self-propagating high-temperature synthesis (SHS) process, in reduced graphene oxide (rGO) synthesized based on the method of Hammers and in the single-walled carbon nanotubes (SWCNT) TUBAL trademark, Russia. Our research has shown that the structure of FLG is free of Stone-Wales defects, while the surface concentration of Stone-Wales defects in TUBAL carbon nanotubes is 1.1×10-5 mol/m2 and 3.6×10-5 mol/m2 for rGO.

Manual visual inspections typically conducted after an earthquake are high-risk, subjective, and time-consuming. Delays from inspections often exacerbate the social and economic impact of the disaster on affected communities. Rapid and autonomous inspection using images acquired from unmanned aerial vehicles offer the potential to reduce such delays. Indeed, a vast amount of re-search has been conducted toward developing automated vision-based methods to assess the health of infrastructure at the component and structure level. Most proposed methods typically rely on images of the damaged structure, but seldom consider how the images were acquired. To achieve autonomous inspections, methods must be evaluated in a comprehensive end-to-end manner, incorporating both data acquisition and data processing. In this paper, we leverage recent advances in computer generated imagery (CGI) to construct a 3D synthetic environment for simulation of post-earthquake inspections that allows for comprehensive evaluation and valida-tion of autonomous inspection strategies. A critical issue is how to simulate and subsequently render the damage in the structure after an earthquake. To this end, a high-fidelity nonlinear finite element model is incorporated in the synthetic environment to provide a representation of earthquake-induced damage; this finite element model, combined with photo-realistic rendering of the damage, is termed herein a physics-based graphics models (PBGM). The 3D synthetic en-vironment with PBGMs provide a comprehensive end-to-end approach for development and validation of autonomous post-earthquake strategies using UAVs, including: (i) simulation of path planning of virtual UAVs and image capture under different environmental conditions; (ii) au-tomatic labeling of captured images, potentially providing an infinite amount of data for training deep neural networks; (iii) availability of the ground truth damage state from the results of the finite-element simulation; and (iv) direct comparison of different approaches to autonomous as-sessments. Moreover, the synthetic data generated has the potential to be used to augment field datasets. To demonstrate the efficacy of PBGMs, models of reinforced concrete moment-frame buildings with masonry infill walls are examined. The 3D synthetic environment employing PBGMs is shown to provide an effective testbed for development and validation of autonomous vision-based post-earthquake inspections that can serve as an important building block for ad-vancing autonomous data to decision frameworks.

With heat treatments to control drywood termites (Blattodea: Kalotermitidae), the presence of heat sinks, which have insulating properties, causes heat to be distributed unevenly throughout the treatment areas. Drywood termites may move to galleries in heat sink areas to avoid exposure to lethal temperatures. To mitigate heat sink effect, studies were conducted in Crytotermes brevis-infested homes in Honolulu, Hawaii to reflect real-world scenarios; either a standard heat treatment performed by a heat remediation company or improved heat treatment methods were used. For improved treatments, heated air was directed into the toe-kick voids of cabinets to reduce heat sink effects. Eight thermistor sensors were placed inside toe-kick voids, in the treatment zone, embedded inside cabinets or the sidewall, or in a wooden cube to monitor internal and ambient temperatures to ensure sufficiently high heat reached all areas. Target temperatures above 46 °C or 50 °C were recorded in all areas for 120 minutes. A pretreatment inspection was conducted, and follow-up inspections were performed at 6 months posttreatment to confirm termite inactivity using visual observations and a Termatrac device. In improved treatment homes, no termite activity was found after treatment. Efficacious heat treatment protocols for structures using the improved method are proposed.

Utilization of Bidirectional Reflectance Distribution Function (BRDF) model parameters obtained from the multi-angular remote sensing is one of the approaches for the retrieval of vegetation structural information. In this research, the potential of multi-angular vegetation indices, formulated by the combination of multi-spectral reflectance from different view angles, for the retrieval of forest above ground biomass was assessed. This research was implemented in the New England region with the availability of a high quality forest inventory database. The multi-angular vegetation indices were generated by the simulation of the Moderate Resolution Imaging Spectroradiometer (MODIS) BRDF/Albedo Model Parameters Product (MCD43A1 Version 6) based BRDF parameters. The effects of seasonal (spring, summer, autumn, and winter) composites of the multi-angular vegetation indices on above ground biomass, angular relationship of the spectral reflectance with above ground biomass, and the interrelationships between the multi-angular vegetation indices were analyzed. Among the existing multi-angular vegetation indices, only the Nadir BRDF-adjusted NDVI ( and Hot-spot incorporated NDVI ( showed significant relationship (more than 50%) with the above ground biomass. This research proposed two more sensitive vegetation structural indices, Fore-scattering Back-scattering NDVI and Vegetation Structure Index (VSI). The Fore-scattering Back-scattering NDVI showed higher sensitivity (R² = 0.62, RMSE = 52.46) towards the above ground biomass than existing multi-angular vegetation indices. Furthermore, the VSI performed in the most efficient way explaining 64% variation of the above ground biomass, suggesting that the right choice of the spectral channel and observation geometry should be considered for improving the estimates of the above ground biomass. In addition, the right choice of seasonal data (summer) was found to be important for estimating the forest biomass while other seasonal data were either insensitive or pointless. The promising results shown by the VSI suggest that it could be an appropriate candidate for monitoring vegetation structure from the multi-angular satellite remote sensing.

The limited information available on the structure of complexes involving transcription factors and cognate DNA response elements represents a major obstacle in the quest to understand their mechanism of action at the molecular level. We implemented a concerted structural proteomics approach, which combined hydrogen-deuterium exchange (HDX), quantitative protein-protein and protein-nucleic acid cross-linking (XL), and homology analysis, to model the structure of the complex between the full-length DNA binding domain (DBD) of FOXO4 and its DNA binding element (DBE). The results confirmed that FOXO4-DBD assumes the characteristic forkhead topology shared by these types of transcription factors, but its binding mode differs significantly from those of other members of the family. The results showed that the binding interaction stabilized regions that were rather flexible and disordered in the unbound form. Surprisingly, the conformational effects were not limited only to the interface between bound components but extended also to distal regions that may be essential to recruiting additional factors to the transcription machinery. In addition to providing valuable new insights into the binding mechanism, this project provided an excellent evaluation of the merits of structural proteomics approaches in the investigation of systems that arematerial not directly amenable to traditional high-resolution techniques.

Many causal factors to marine traffic accidents (MTA) influence each other and have associated effects. It is necessary to quantify the correlation path mode of these factors to improve accident prevention measures and their effects. In the application of human factors to the accident mechanisms, the complex structural chains on causes to MTA systems were analyzed combining the Human Failure Analysis and Classification System (HFACS) with theoretical Structural Equation Modeling (SEM). First, the accident causation model was established as a human error analysis classification in sight of MTA, and the constituent elements of the causes of accident was conducted. Second, a hypothetical model of Human factors classification was proposed applying the practice of the structural model. Third, with the data resource from ship accident cases, this hypothetical model was discussed and simulated, and as a result the relationship path dependency mode between the latent independent variable of the accident was quantitatively analyzed based on the observed dependent variable of human behaviors. Application examples show that relationships in HFACS are verified and in line with the path developing mode, and resource management factors have a pronounced influence and a strong relevance to the causal chain of the accidents. Appropriate algorithms for the theoretical model can be used to numerically understand the safety performance of marine traffic systems under different parameters through mathematical analysis. Hierarchical assumptions in the HFACS model are quantitatively verified.

Fibre-reinforced composite structures under complex loads exhibit gradual damage behaviour with a degradation of effective mechanical properties and change of their structural dynamic behaviour. Damage manifests itself as spatial increase of inter-fibre failure and delamination-growth, resulting in local changes of stiffness. These changes affect not only the residual strengths but more importantly the structural dynamic behaviour. In case of composite rotors, this can lead to catastrophic failure if an eigenfrequency coincides with the rotational speed. The description and analysis of the gradual damage behaviour of composite rotors therefore provides the fundamentals for a better understanding of unpredicted structural phenomena. The gradual damage behaviour on the example of composite rotors and the resulting damage-dependent dynamic behaviour is experimentally investigated under propagating damage for combined out-of-plane and in-plane loads. A novel observation is reported, where monotonic increase of damage results in non-monotonic frequency shift of significant amount of eigenfrequencies.

There are numerous approaches to model an influence of manufacturing parameters on the dissolution and disintegration of solid dosage forms. A modern approach for modelling and simulating complex and heterogeneous systems such as pharmaceutical tablets focuses on computationally-intensive finite-element or discreet element methods. Industrial challenges such as Process Analytical Technology (PAT) and Quality by Design are stimulating computer-based technologies to design, control and improve the quality of pharmaceutical compacts and their performance. In this study the disintegration and dissolution model based on the numerical solutions of the Noyes-Whitney equation and cellular automata supported disintegration model are proposed and evaluated. The results from in vitro release studies of the mefenamic acid formulations were compared to the calculated release patterns from the tablet structures obtained from microtomography experiments and the purely algorithmically created virtual tablets.

The traditional manual recording of vaccination records in Germany faced challenges during the COVID-19 pandemic, prompting the introduction of a Covid smartphone app with QR codes. However, this solution brought new challenges, emphasizing the need for a centrally managed European digital vaccination record for efficiency and validity. Thus, this study assesses the feasibility of using the HL7 FHIR standard in the healthcare industry for implementing a digital vaccination pass management and monitoring system. The system aims to offer convenience and improved efficiency for both patients and healthcare providers while promoting interoperability with other healthcare systems. We developed a prototype using modern technologies, such as React, Quarkus, and Keycloak, evaluating the applicability of FHIR in promoting interoperability within the healthcare industry. Results indicate potential benefits for patients and healthcare providers, offering secure access to immunization records, personalized recommendations, and streamlined management. However, challenges in integrating nuanced vaccination processes into the standardized FHIR system, necessitating custom extensions, and issues with manual data entry and identity provider integration, pose obstacles. Despite these challenges, the study suggests that implementing HL7 FHIR can enhance efficiency, data accessibility, and accuracy in the vaccination process, supporting broader digitization efforts in the German healthcare system and beyond.

The application of thermoelectric generators (TEG) on the nozzle of an aviation jet engine was studied by finite element TEG-simulations. Against the background of system-level requirements of the reference aircraft this work reports the resulting requirements on the TEG design with respect to applied thermoelectric (TE) element lengths and fill factors (F) within the TE modules in order to maintain a positive effect on the specific fuel consumption. Assuming a virtual optimized TE material and varying the convective heat transfer coefficients at the nozzle surfaces this work reports the achievable power output. System-level requirement on the gravimetric power density (> 100 Wkg-1) can only be met for F ≤ 21%. Extrapolating TEG coverage to the full nozzle surface, the power output reaches 1.65 kW per engine. Assessment of further potential is demonstrated by a parametric study on the fill factor, convective heat transfer coefficients, and materials performance. This study confirms a feasible design range for TEG installation on the aircraft nozzle with a positive impact on the fuel consumption. This application translates into a reduction of operational costs, allowing for an economically efficient installation of TEG in consideration of the cost-specific power output of modern thermoelectric materials.

The paper presents a method for estimating the inertia tensor components of a spacecraft that has expired its active life using measurement data of the Earth's magnetic field induction vector components. The implementation of this estimation method is supposed to be carried out when cleaning up space debris in the form of a clapped-out spacecraft with the help of a space tug. It is assumed that a three-component magnetometer and a transmitting device are attached on space debris. With the help of this measuring system, the parameters for the rotational motion of space debris are estimated. Then the known controlled action from the space tug is transferred to the space debris. Next, measurements for the rotational motion parameters are carried out once again. Based on the available measurement data and parameters of the controlled action, the space debris inertia tensor components are estimated. It is assumed that the measurements of the Earth's magnetic field induction vector components are made in a coordinate system which axes are parallel to the corresponding axes of the main body axis system. Such an estimation makes it possible to effectively solve the problem of cleaning up space debris, to calculate the costs of the space tug working body and the parameters of the space debris removal orbit. Examples of numerical simulation using the measurement data of the Earth's magnetic field induction vector components on the Aist-2D small spacecraft are given. The results of the work can be used in the development and implementation of missions to clean up space debris in the form of clapped-out spacecraft.

The current paper is studying the influence of geometrical parameters of the FDM (FFF) 3D printing process on printed part strength for open source desktop 3D printers and the most popular material used for that purpose, i.e. PLA (polylactic acid). The study was conducted using a set of different nozzles (0.4, 0.6 and 0.8 mm) and a range of layer heights from the minimum to maximum physical limits of the machine. To assess print strength, a novel assessment method is proposed. A tubular sample is loaded in the weakest direction (across layers) in a three-point bending fixture. To explain the results obtained, a mesostructure evaluation through SEM scans of the samples were used. A significant influence of geometric process parameters was detected on sample mesostructure and, consequently, on sample strength.

This review describes and discusses unusual axonal structural details and evidence for unmasking of sulfhydryl groups (-SH) in axoplasmic membranes resulting from electrical stimulation or asphyxia. Crayfish axons contain fenestrated septa (FS) that in phase contrast micrographs appear as repeated striations. In the electron microscope each septum is made of two cross-sectioned membranes containing ~550 Å pores, each occupied by a microtubule. Thin filaments, likely to be made of kinesin, bridge the microtubule to the edge of the pore. FS are believed to play a role in axoplasmic flow. The axons also display areas in which axon and sheath-glial cell plasma membranes are sharply curved and project into the axoplasm. In freeze-fractures, the protoplasmic leaflet (P-face) of the projections appears as elongated indentations containing parallel chains of particles. The sheath-glial cell plasma membrane also contains particles, but they are irregularly aggregated. The axons also display areas where axonal and glial plasma membranes fuse, creating intercellular pores. In axons fixed during electrical stimulation the plasma membrane, the outer membrane of mitochondria, membranes of other cytoplasmic organelles and gap junctions increase in electron opacity and thickness, resulting from unmasking of sulfhydryl groups (-SH). Similar changes occur in asphyxiated nerve cords.

Ostreococcus tauri is a simple unicellular green alga representing an ecologically important group of phytoplankton in oceans worldwide. Modern molecular techniques must be developed in order to understand the mechanisms that permit adaptation of microalgae to their environment. We present for the first time in O. tauri a detailed characterization of individual genomic integration events of foreign DNA of plasmid origin after PEG-mediated transformation. Vector integration appears to be random, occurring mainly at a single locus, and thus confirming the utility of this technique for insertional mutagenesis. While the mechanism of double-stranded DNA repair in the O. tauri model remains to be elucidated, we clearly demonstrate by genome resequencing that the integration of the vector leads to frequent structural variations (deletions/insertions and duplications) and some chromosomal rearrangements in the genome at the insertion loci, and often within the vector sequence itself. From these observations, we speculate that a non-homologous end joining-like mechanism is required during random insertion events, as described in plants and other freshwater algal models. PEG-mediated transformation is therefore a promising molecular biology tool, not only for functional genomic studies, but also for biotechnological research in ecologically important marine algae.

Metazoans have an elaborate and functionally segmented body. It evolves from a single cell by systematic divisions. Metazoans attain structural complexity with exquisite precision, which is a molecular mystery. The indispensable role of centrioles in cell division and ciliogenesis can shed insight into this riddle. Cell division helps in growth of the body and is a highly regulated and integrated process. Its errors cause malignancies. The cell mass is organized during organogenesis. Prior to it, the centrioles are retrieved from the cell cycle to initiate ciliogenesis. The cilia-modulated developmental signaling pathways elaborate the body plan. The secluded compartment of the cilium reduces noise during signaling and is essential for a precise body plan development. The dysfunctional centrioles and cilia can distort body plan. Thus, centriole has a dual role in growth and cellular organization. This concept review analyses the comprehensive interactome and the key domain features (like C2 domain) of molecules which connect and disarm the centriole from the cell cycle and ciliogenesis by switching on or off the essential regulators of the pathways. The concentration of these signaling pathways at the centriole reinforces the hypothesis that centriole is the molecular workstation to carve out structural design and complexity in metazoans.

Nuclear export of viral mRNAs, is an essential step in the HIV replication cycle. This role is played by a small regulatory protein of HIV-1 called Rev.The N-terminal region of Rev contains an arginine-rich sequence. The arginine-rich motif (ARM) is located between amino acids 38-50 and forms an alpha-helical secondary structure. Expression of the structural proteins of human immunodeficiency virus type 1 requires the direct interaction of multiple copies of the viral Rev protein with its highly structured RNA target sequence, the Rev Response element (RRE). The major viral proteins are not produced if this transport of RNA is stopped. Therefore, knowledge of Rev structure is essential for understanding of its cooperative binding to the RRE, for understanding the mechanism of HIV infection and for the development of antiviral drugs that interfere with Rev’s essential functions and for acknowledgment of good candidate drugs for treatment of AIDS. To understand how REV interact with RRE element of HIV-RNA and its formation of oligomeric complex it is better to characterize the domain wise structure of REV with regard in function of each domain. Due to lack of structural data on Rev no single compound is reported as inhibitor of REV expect antiviral drugs. Identification of a high-affinity RNA-binding site for the human immunodeficiency virus type 1 Rev Protein is much more important. The ARM is a highly specific sequence which allows for the multimerization of Rev and also binding of REV with RNA. Here we are first time exploring the structural characteristics of REV protein both in free form and in complex with RNA at domain function level especially explore the role of ARM motif in REV HIV-1 protein as RNA binding sites by molecular dynamics (MD) simulation and homology modeling studies. Results indicate that the arginine-rich motif (ARM) is crucial in stability of this complex. The residues ARG38, 39, 41, 43, 44, 48, 50, and ASN40 are most interacting with nucleobases of RRE in Crystal structure of Rev and Rev-response-element RNA complex. Our study plays a major role in elaboration of binding of RNA with REV and pave the way for further investigation for therapeutically agent for HIV.

Biomimetic compounds are an alternative for to the limited action and fragile nature of enzymes. This work deals with the synthesis, characterization and evaluation of catalytic activity of two new biomimetic models for the active centers of ascorbate oxidase and catalase. [Cu3(S,S(+)cpse)3(H2O)3][Cu3(R,R(-)cpse)3(H2O)3]·17H2O (model for ascorbate oxidase, 1), and [Mn2(S,S(+)Hcpse)4(NaClO4)2(NaOH)(CH4O)]n·[(C2H6O)2]n·[(CH4O)2]n (model for catalase, 2) were prepared through the synchronic method (yields > 78%). The compound 1 has electronic and optical characteristics for racemic compound. The magnetic properties and electrochemical behavior evidence electronic transfer between metal centers. Meanwhile, the compound 2 showed polymeric properties in solid state and dimeric behavior in solution. Compound 1 was able to effectively catalyze the oxidation of ascorbic acid to dehydroascorbic acid (65.6% and 78.24% for racemic and enantiomeric pure compounds) showing structural and functional similarity to the natural enzyme. Besides, Compound 2 catalyzed the decomposition of hydrogen peroxide toward oxygen and water molecules (45%), evidencing that the prepared complex mimics the action of catalases. These two biomimetic models are relationship between them for the structural ligands, the coordination form to metal center and the catalytic activity as oxidase. This research shows the relationship with the design, evaluation, and comprehension of fundamentals aspects for the biomimetic models of active center of metalloenzymes that have importance for biological and industrial processes.

This paper introduces the improvements in the natural frequency based Structural Health Monitoring (SHM) by applying bio-inspired optimization methods and the vision-based monitoring system for the effective damage detection. This paper proposes a natural frequency extraction method using the motion magnification based vision monitoring system with bio-inspired optimization techniques to estimate the damage location and depth in a cantilever beam. The proposed optimization techniques are inspired by natural processes and biological evolution including Genetic Algorithms, Particle Swarm Optimization, Sea Lion Optimization, and Coral Reefs Optimization. To verify the performances of each bio-inspired optimization methods, the eigenvalues of a two-bay truss structure are used for estimating the damaged elements. Then, using the proposed video motion magnification method, the natural frequency for each of undamaged and damaged cantilever beam have been extracted and compared with the LDV sensor to verify the proposed vision-based monitoring system. The performance of each bio-inspired optimizer for the damage detection has been compared. As a result, Coral Reefs Optimization has showed the lowest average error, around 1%, in the damage detection using natural frequency.

The goal of this article is to provide a review of the experimental techniques and procedures using vibration methods for the Structural Health Monitoring (SHM) of Polymer-Matrix Composites (PMC). It aims to be a guide for any researchers to carry out vibration experiments. The linear methods are first introduced. But as PMC is a complex material, these classic methods showed some limits, such as low accuracy for small damages, and a high environmental dependency. This is why the nonlinear methods are secondly studied, considering that the complexity of PMC induces a nonlinear behavior of the structure after damage occurrence. The different damage mechanisms are well explained in order to evaluate the potential of each vibration method to detect them.

The Odunpazarı Modern Museum (OMM), conceptualized by Architect Kengo Kuma and inaugurated in 2019 in Eskişehir, stands as a testament to the historical significance of the timber trade in the region. The deliberate choice of wood as the primary construction material serves as a tribute to this historical narrative. The conspicuous incorporation of wooden lath materials into both the external and internal spaces signifies a conscious reference to the region's historical heritage and aligns with sustainability principles in design. The timber used to construct OMM was sourced from exhausted industrial pine forests. The creation of exhibition spaces at diverse scales involved the assembly of boxes of varying dimensions, illustrating OMM's inclination towards a formative structure characterized by “Addition and Integration.” This architectural methodology involves juxtaposing two or more primary forms to achieve a partial amalgamation. Factors such as form characteristics, dimensional distinctions, spatial arrangements, and extent of surface interactions collectively contribute to the compelling effect of this integrative approach. Within the confines of the museum, unconventional partitioning is implemented, and the strategic arrangement of masses results in multiple façades, even in the absence of overt wooden surfaces. The discernible visibility of the building's façade from an internal vantage point underscores the pivotal role played by wood in the architectural design of the OMM. The exterior impact of the wooden shell complements its interior application. The voluminous void at the heart of the structure allows for the infiltration of natural light into the internal spaces, and the wooden facade facilitates the transmission of light. The use of glass to segregate the cafeteria area from the museum entrance preserves a visual continuity between these spaces. The fundamental research inquiry in this study revolves around the user experience of wood, a material that actively influences diverse facets, including structural elements, contextual considerations, interior arrangements, and external aesthetics. To address this inquiry, a comprehensive case study and survey were conducted with the objective of elucidating the functional, sensory, perceptual, and psychological impacts of wood, the primary material in the museum's spatial configuration, on the overarching user experience.

Recently, more wind turbine systems are being installed in deep waters far from the coast. Several concepts of floating wind turbine systems (FWTSs) are developed, among which the semisubmersible platform, due to its applicability in different water depths, good hydrodynamic performance, and facility in the installation process, constitutes the most explored technology compared to the others. However, a significant obstacle to the industrialization of this technology is a design of a cost-effective FWTS, which can be achieved by optimizing the geometry, size and weight of the floating platform, along with the mooring system. This is only possible by selecting a method capable of accurately analyzing the FWTS coupled hydro-aero-structural dynamics at each design stage. Accordingly, this paper aims at providing a detailed overview of the most common coupled numerical and physical methods, including their basic assumptions, formulations, limitations, and costs, used for analyzing the dynamics of FWTSs, mainly those supported by a semisubmersible, to assist the choice of the most suitable method at each design phase of FWTSs. Finally, the article discusses possible future research to address challenges in modeling FWTSs dynamics that persist to date.

Astrocytes are morphological intricate cells and actively modulate the function of the brain. Through the numerous fine processes, astrocytes contact with neurons, blood vessels and other glia cells. Emerging evidence have shown that astrocytes exhibit brain-regional diversity in the morphology, transcriptome, calcium signaling and functions. However, little is known about the brain regional heterogeneity of astrocyte-astrocyte structural interaction. So far, the visualization and characterization of the morphological features for the adjacent astrocytes with high resolution has been difficult, and as a result, it is still well accepted that astrocytes in the adult brain share non-overlapped territory. In contrast, by using an approach that combines sparse viral labeling with dual-fluorescent dyes, which allows for efficient and specific labeling of adjacent astrocytes, thus enabling a comprehensive visualization of their fine processes and the degree of their territorial overlap. Our study in the hypothalamic regions revealed a marked spatial overlap among adjacent astrocytes. Additionally, we revealed the heterogeneity of astrocyte-neuron ratio across brain regions, and conducted an assessment of the photostability and labeling efficiency of fluorescent dyes used for labeling adjacent astrocytes. Our study here provides new insights for studying the morphological heterogeneity of astrocytes across the central nervous system.

Bis-benzimidazole derivative (BBM) molecule, consisting of two 2-(2’-Hydroxyphenyl) benzim-idazole (HBI) halves, has been synthesized and successfully utilized as a ratiometric fluorescence sensor for the sensitive detection of Cu2+ based on enol-keto excited state intramolecular proton transfer (ESIPT). In this study, we strategically implement femtosecond stimulated Raman spec-troscopy and several time-resolved electronic spectroscopies, aided by quantum chemical calcula-tions to investigate the detailed primary photodynamics of BBM molecule. The results demonstrate that the ESIPT from BBM-enol* to BBM-keto* was observed in only one of HBI halves with a time constant of 300 fs, after that, the rotation of the dihedral angle between two HBI halves generate a planarized BBM-keto* isomer in 3 ps, leading to dynamics red shift of BBM-keto* emission.

CoCr2O4 and doped lithium Co1-xLixCr2O4 chromate powder and nanoparticles were prepared by modified by sol-gel method. The morphological and structural properties of nano chromates were investigated by x-ray diffraction (XRD), scanning electron microscopy (SEM), Raman spectroscopy and Photoluminescence (PL). Nanoparticles of doped lithium were synthesized by adding appropriate amount of cobalt nitrate, chromium nitrate, lithium nitrate and 1,2 Ethanediol as a complexing agent. The sample were heated at 105 ˚C for ten hours in oven to obtain dry gel. Calcination temperature for these samples was 700˚C for 3 hours in a furnace. The particle size of parent compound ranges from 4.4 nm to 11 nm, determined by SEM. The tendency of particles to form the aggregates with the increased annealing temperature was observed. The SEM and optical characterization of this compound has shown the sol gel derived material may be successfully used as an effective doped lithium cobalt ceramic pigment with controlled variation in structural and optical properties. SEM images showed that spherical like doped particle have diameter 33nm. From PL spectra Nano structure shows band gap 2.5ev and when we doped Lithium in it band gap decreases and become 1.19ev, which is associated to band gap transition.

Purpose: Pandemic Novel Coronavirus (SARS-CoV-2) has emerger centered from wuhan, China. Structurally homologous spike protein of SARS-CoV-2 receptor is taxonomically homologous with SARS-Cov and SARS associated bat coronavirus. Still now scientists are trying to find out proper vaccine and treatments for this disease. Methods: Systematically we modeled and compared the structure of SARS-CoV-2 spike protein along with Bat Cov, Bat SARS Cov and SARS Cov Urbani. S1 and S2 unit of the coronavirus (SARS-CoV-2) are attached with ACE2 and furin, here we docked 5 Ca+ chelating drugs with these two proteins. Results: Structural comparison with all these spike proteins revealed that less significant but not negligible difference exists among them. Inserted stable nucleotide sequences and corresponding surface exposed peptidal region may be considered as epitope. Docking result with Toxicokinetics and half life of Penicillamine can effectly inhibit the attachment site of spike protein of coronavirus (SARS-CoV-2). Conclusions: Docking summery and the pharmacokinetics with toxicokinetics index recommend that Penicillamine can able to inhibit the infection of SARS-CoV-2.

During its first month, the recently emerged 2019 Wuhan novel coronavirus (SARS-CoV-2) has already infected many thousands of people in mainland China and worldwide and took hundreds of lives. However, the swiftly spreading virus also caused an unprecedentedly rapid response from the research community facing the unknown health challenge of potentially enormous proportions. Unfortunately, the experimental research to understand the molecular mechanisms behind the viral infection and to design a vaccine or antivirals is costly and takes months to develop. To expedite the advancement of our knowledge we leverage the data about the related coronaviruses that is readily available in public databases, and integrate these data into a single computational pipeline. As a result, we provide a comprehensive structural genomics and interactomics road-maps of SARS-CoV-2 and use these information to infer the possible functional differences and similarities with the related SARS coronavirus. All data are made publicly available to the research community at http://korkinlab.org/wuhan .

Excitotoxicity related to the dysfunction of the N-methyl-d-aspartate receptor (NMDAR) has been indicated to play an integral role in the pathophysiology of multiple disease states, including neurodegenerative disorders such as Parkinson’s disease. There is a notable gap in the market for novel NMDAR antagonists, however current methods to analyze potential antagonists rely on indirect measurements of calcium flux and hazardous radioligand binding assays. Recently, a fluorescent NMDAR ligand, N-adamantan-1-yl-dimethylamino-1-naphthalenesulfonic acid, known as AM-DAN was developed by our group. Additional studies on this ligand is necessary to evaluate its potential as a biological tool in NMDAR research. Therefore, this study was aimed at conducting structural analyses, fluorescence experiments, high-accuracy NMDAR molecular modelling and NMDAR phencyclidine (PCP) site competition binding studies using AM-DAN. Results revealed that AM-DAN has appropriate structural properties, significant fluorescent ability in various solvents and is able to bind selectively and compete for the PCP-binding site of the NMDAR. Therefore, AM-DAN holds promise as a novel fluorescent ligand to measure the affinity of prospective drugs binding at the NMDAR PCP-site and may circumvent the use of radioligands.

Project complexity is usually considered as one of main causes of cost overruns, resulting in poor performance and thus project failure. However, empirical studies focused on evaluating its effects on project cost remain lacking. Given this circumstance, this study attempts to develop the relationships between project cost and the multidimensional project complexity elements. We establish complexity as a multidimensional factor including the task, organization, market, legal, and environment complexities. This study uses an empirical evidence-based structural model to account for the relationships between project cost and project complexity. By doing so, a quantitative assessment of multi-dimensional project complexity has been developed. The findings suggest that task and organization complexities have direct effects on project cost, while market, legal and external environment complexities have indirect effects on project cost. The practical contribution is that the findings can improve the understanding of which dimension of complexity significantly influence project cost, and the need to focus efforts on strategically addressing that complexities.

Filament wound composite pipes are frequently used in the field were transmission of high pressured chemical fluids, disposal of industrial wastes, oil and natural gas transmission takes place. In oil and gas industry, the pipelines transporting heavy crude oil are subjected to variable pressure waves causing fluctuating stress levels in the pipes. Computational Fluid Dynamics Analysis was performed using Ansys 15.0 Fluent software to study the effects of these pressure waves on some specified joints in the pipes. Depending on the type of heavy crude oil being used, the flow behavior indicated a considerable degree of stress levels in certain connecting joints, causing the joints to become weak over a prolonged period of use. In this research comparison of various pipe joints was done by using different material and the output result of the stress levels of the pipe joints were checked so that the life of the pipe joints can be optimized by the change of material.

Helicobacter pylori cytotoxin-associated gene A protein (CagA) has been associated with the increase in virulence and risk of cancer. It has been demonstrated that CagA's translocation is dependent on its interaction with phosphatidylserine. We evaluated the variability of the N-terminal CagA in 127 sequences reported in NCBI, by referring to molecular interaction forces with the Phosphatidylserine and the docking of 3 mutations chosen from variations in specific positions. The major sites of conservation of the residues involved in CagA-Phosphatidylserine interaction were 617, 621 and 626 which had no amino acid variation. Position 636 had the lowest conservation score, so mutations in this position were evaluated to observe the differences in intermolecular forces of the CagA-Phosphatidylserine complex. We evaluated the docking of 3 mutations: K636A, K636R and K636N. The models of the crystal and mutations presented a ΔG of −8.919907, −8.665261, −8.701923, −8.515097 Kcal/mol, respectively, while mutations K636A, K636R, K636N and the crystal structure presented 0, 3, 4 and 1 H-bonds, respectively. Likewise, the bulk effect of the ΔG and amount of H-bonds was estimated in all of the docking models. The type of mutation affected both the ΔG (χ²(1) = 93.82, p-value < 2.2 × 10⁻¹⁶) and the H-bonds (χ²(1) = 91.93, p-value < 2.2 × 10⁻¹⁶). In all the data, 76.9% of the strains that exhibit the K636N mutation produced a severe pathology. The average H-bond count diminished when comparing the mutations with the crystal structure of all the docking models, which means that other molecular forces are involved in the CagA-Phosphatidylserine complex interaction.

Alzheimer's disease (AD) is a stealthy and progressive neurological disorder that is a leading cause of dementia in the global elderly population, imposing a significant burden on both the elderly and society. Currently, the condition is treated with medications that alleviate symptoms. Nonetheless, these drugs may not consistently produce the desired results and can cause serious side effects. Hence, there is a vigorous pursuit of alternative options to enhance the quality of life for patients. Ginkgo biloba (GB), an herb with historical use in traditional medicine, contains bioactive compounds such as terpenoids (Ginkgolides A, B, and C), polyphenols, organic acids, and flavonoids (quercetin, kaempferol, and isorhamnetin). These compounds are associated with anti-inflammatory, antioxidant, and neuroprotective properties, making them valuable for cognitive health. A systematic search across three databases using specific keywords GB in AD and dementia yielded 1702 documents, leading to the selection of 15 clinical trials for synthesis. In eleven studies, GB extract/EGb 761® was shown to improve cognitive function, neuropsychiatric symptoms, and functional abilities in both dementia types. In four studies, however, there were no significant differences between the GB-treated and placebo groups. Significant improvements were observed in scores obtained from the Mini-Mental State Examination (MMSE), Short Cognitive Performance Test (SKT), and Neuropsychiatric Inventory (NPI). While the majority of synthesized clinical trials show Ginkgo biloba has promising potential in these conditions, more research is needed to determine optimal dosages, effective delivery methods, and appropriate pharmaceutical formulations. Furthermore, a thorough assessment of adverse effects, exploration of long-term use implications, and investigation into potential drug interactions are critical aspects that must be carefully evaluated in future studies.

The COVID 19 pandemic saw the emergence of various Variants of Concern (VOCs) that took the world by storm, often replacing the ones that preceded them. The characteristic mutant constellations of these VOCs increased viral transmissibility and infectivity. Their origin and evolution remain puzzling. With the help of data mining efforts and the GISAID database, a chronology of 22 haplotypes described viral evolution up until July 23, 2023. Since the 3-dimensional atomic structures of proteins corresponding to the identified haplotypes are not available, ab initio methods were here utilized. Regions of intrinsic disorder proved to be important for viral evolution, as evidenced by the targeted change to the nucleocapsid (N) protein at the sequence, structure, and biochemical levels. The linker region of the N-protein, which binds to the RNA genome and self-oligomerizes for efficient genome packaging, was greatly impacted by mutations throughout the pandemic, followed by changes in structure and intrinsic disorder. Remarkably, VOC constellations acted cooperatively to balance the more extreme effects of individual haplotypes. Our strategy of mapping the dynamic evolutionary landscape of genetically linked mutations to the N-protein structure demonstrates the utility of ab initio modeling and deep learning tools for therapeutic intervention.

This paper aims to propose improvements for plastic waste management in Salvador – the Brazilian third most populated metropolis – via Partial Least Squares Structural Equation Modeling (PLS-SEM). All indicators, constructs, and hypotheses regarding collection, sorting, recycling, and disposal in the proposed PLS model were derived from the literature review, and the dependence of the performance construct on efficiency, effectiveness, municipality's socioeconomic aspects and municipality infrastructure is evaluated. Academic and practitioner publics were surveyed, and after analysis in both SmartPLS and RStudio software, suggestions for improvement regarding plastics recycling rate, market maturity, and infrastructural aspects for optimized reverse logistics were made. Since almost double the minimum number of respondents answered the survey questionnaire and the PLS-SEM statistics showed that the modeling presents consistency, the discussion is relevant. The model can and will evolve, but examples of suggested improvement are the installation of Deposit-Return Systems (DRS) in parks, streets, and avenues for increasing selective collection and the direct purchasing of waste from residents by municipal administration, compensating them with vouchers for food. The model can be a basis for other cities worldwide sharing analogous characteristics. By considering it, organizations can contribute to both reduced Greenhouse Gas (GHG) emissions and reduced terrestrial pollution.

While machine learning (ML) has been quite successful in the field of structural health monitoring (SHM), its practical implementation has been limited. This is because ML model training requires data containing a variety of distinct damaged instances captured from a real structure and the experimental generation of such data is challenging. One way to tackle this issue is by generating training data through numerical simulations. However, simulated data cannot capture the bias and variance of experimental uncertainty. To overcome this problem, this work proposes a deep learning-based domain transformation method for transforming simulated data to the experimental domain. Use of this technique has been demonstrated for debonding location and size prediction of stiffened panels using a vibration-based method. The results are satisfactory for both, debonding location and size prediction. This domain transformation method can be used in any field where experimental data for training machine learning models is scarce.

This study investigates the critical success factors (CSFs) of Lean Six Sigma (LSS) implementation and their impact on organizational growth in Nigerian enterprises. The objectives were to identify crucial CSFs for successful LSS deployment and assess their significance in achieving organizational growth. A mixed-method approach was used, including literature analysis, expert judgments, and a survey of 130 participants from various industries. The survey questionnaire employed a 5-point Likert scale to collect data on LSS CSFs and implementation success metrics. Structural equation modeling (SEM) with SmartPLS 4.0 analyzed the data, revealing that LSS CSFs significantly contribute (up to 39.2 percent) to the success of LSS implementations. The study identified 12 critical LSS CSFs, categorized into workers, business, and management, each influencing LSS implementation. Recommendations include creating a supportive environment, providing comprehensive training, and prioritizing continuous improvement efforts for successful LSS deployment. Future research possibilities include longitudinal studies, sector-specific analyses, and qualitative investigations to deepen understanding and enhance LSS implementation outcomes. In conclusion, successful LSS implementation empowers Nigerian organizations with improved productivity, waste reduction, and sustainable production systems, leading to overall growth and success.

(1) Background: Stereological estimations significantly contributed to our anatomical and physiological understanding of the lung by providing an average distribution of measured parameters over the entire lung parenchyma. However, most structural lung diseases show a very inhomogeneous pattern of alterations. (2) Methods: We developed a novel protocol for the analysis of all pulmonary airspaces. Our pipeline starts with high-resolution synchrotron radiation-based X-ray tomographic microscopy (SRXTM) and consists of (i) image segmentation with the combination of the free machine-learning tool Ilastik and ImageJ and (ii) calculation of the airspace diameter distribution of an entire lung using a diameter map function. To evaluate the new pipeline, lungs from adult mice with cystic fibrosis (CF)-like lung disease (ENaC-transgenic mice) or mice with elastase-induced emphysema were compared to healthy controls. (3) Results: We were able to show the distribution of airspace diameters throughout the entire lung, as well as separately for the conducting airways and the gas-exchange area. In the pathobiological context, we observed an irregular widening of parenchymal airspaces in mice with CF-like lung disease and elastase-induced emphysema. Comparable results were obtained when analyzing lungs imaged with μCT, suggesting that our pipeline is applicable to different kinds of imaging modalities. (4) Conclusions: We conclude that the airspace diameter map is well suited for a detailed analysis of unevenly distributed structural alterations in chronic muco-obstructive lung diseases such as cystic fibrosis and COPD.

In order to sustain the marine environment relationship between the environmental factors and marine biota must be investigated. This study aims to study such a correlation in the adjacent waters of Nan Wan Bay, Kenting, Taiwan, and to explore the covariance of environmental factors on marine life (whether they enhance or diminish it). To achieve these objectives, factor analysis was used to identify potential latent variables that could affect the water quality of the adjacent waters, including phytoplankton (quantity), zooplankton (quantity), and fish (quantity and species). These potential variables were named based on the results of past studies and related literature. Finally, a structural equation model (SEM) was constructed to establish a marine ecological model among the potential variables. The factor analysis results revealed that nutrients, upwelling, and primary productivity are the primary factors affecting the environmental changes in the adjacent waters of Nan Wan Bay. The comprehensive SEM showed that nutrients and primary productivity significantly impact plankton. Path analysis indicated that primary productivity has the highest direct effect on the phytoplankton cluster. However, the upwelling has a low significance in its effect on phytoplankton, zooplankton, and fish clusters. Compared to the results of past related studies, the SEM proposed in this study can reflect a considerable degree of change in the waters.

Abstract: Changes in sugar composition occur continuously in plants tissues, at different develop-mental stages. Tuber dormancy induction, stability, and breaking are very critical developmental transitions in yam crop production. Prolonged tuber dormancy after physiological maturity has constituted a great challenge in yam genetic improvement and productivity. In the present study, biochemical profiling of non-structural sugar in yam tuber during dormancy was performed to determine the role of non-structural sugar in yam tuber dormancy regulation. Two genotypes of white yam specie; one local genotype (Obiaoturugo) and (TDr1100873) were used for this study. Tubers were sampled at (42, 56, 87, 101, 115, and 143) days after physiological maturity (DAPM). Obiaoturugo exhibited a short dormant phenotype and sprouted at 101DAPM, whereas TDr1100873 exhibited a long-dormant phenotype, and sprouted at 143DAPM. Significant metabolic changes were observed in non-structural sugar parameters, dry matter, and moisture content in Obiaoturugo from 56DAPM, whereas, in TDr1100873 significant metabolic changes were observed from 101DAPM. It was observed that the onset of these metabolic changes occurred at a point when the tubers of both genotypes exhibited dry matter content of 60%, indicating that dry matter content of 60% might be a critical threshold for white yam tuber sprouting. Nonreducing sugars increased by 9-10-fold during sprouting in both genotypes which indicates its key role in tuber dormancy regulation in white yam. This result implies that some key sugar metabolites can be targeted for dormancy manipulation of yam crop.

Vip3 proteins are increasingly used in insect control in transgenic crops. To shed light on the structure of these proteins, we used the approach of trypsin fragmentation of mutants altering the conformation of the Vip3Af protein. From an alanine scanning on Vip3Af, we selected mutants with an altered proteolytic pattern. Based on the protease digestion patterns, their effect on oligomer formation, and theoretical cleavage sites, we generated a map of the Vip3Af protein with five domains, which match some of the domains proposed independently by two in silico models. Domain I ranges from aa12-198, domain II from aa199-313, domain III from aa314-526, domain IV from aa527-668 and domain V from aa669-788. The effect of some of the mutations on the ability to form a tetrameric molecule revealed that domains I-III are required for tetramerization, while domain V is not. The involvement of domain IV in the tetramer formation is not clear. Some mutations distributed from near the end of domain I up to the end of domain II affect the stability of the first three domains of the protein and negatively impact oligomerization upon trypsin treatment. Because of the high sequence similarity among Vip3 proteins, we propose that our domain map can be extended to many other members of the Vip3 family of proteins.

The quality of an educational system is reflected not only in the instructive performances of the educational actors, but also in the degree in which it ensures an adequate professional integration. The undergraduate of today, the graduate of tomorrow needs an as accurate as possible information regarding the labour market, which cannot be achieved only by individual means, but also by resorting to carrier counselling services. The motivation of this research is closely connected to the improvement of the level of communication between the two aspects – on the one hand the academic one, by its finite products, and the economic one, on the other hand – and the opportunities that the cooperation between the two aspects might offer: adjusting the demand-supply ratio on the labor market and above all, stopping massive emigration of young graduates of higher education.

In a wireless network, locations of base stations (BSs)/access points (APs)/sensor nodes can be modeled based on stochastic processes, e.g., a Poisson point process (PPP) or a deterministic pattern planned ahead by providers. While deterministic deployment does not provide tractable interference analysis in general, PPP yields tractable analysis for interference. However, PPP allows APs to be deployed very close to each other and gives pessimistic results compared to the field measurements. In this study, in order to address this issue, Lloyd’s algorithm, which functions as a bridge between random and structural APs deployments, is investigated for analyzing coverage probability in a network. The link distance distribution is modeled as a mixture of Weibull distributions and its parameters are obtained by using the expectation-maximization (EM) algorithm for each iteration of Lloyd’s algorithm. The link distance distribution is further utilized for calculating the coverage probability approximately by exploiting the tractability of PPP.

(1) Background: Since fullerene C60 is insoluble in water and is toxic, it is not applicable in biomedicine and cosmetics. For this reason, the first derivative FD-C60 (fullerenol) was synthesized, which solved the problem of solubility in water and partially reduced toxicity. In order to maximally reduce toxicity and increase biomedical efficiency, the second derivative SD-C60 (3HFWC- Hyper-Harmonized-Hydroxylated Fullerene Water Complex), was created. (2) Methods: In order to obtain the most reliable data, several different methods are applicable in the characterization of FD-C60 and SD-C60 with water layers (NIR, FTIR, 13C-NMR,  1H-NMR, TGA/DTA, XRD, AFM/MFM etc.). (3) Results: FD-C60 as an individual structure is about 1.3 nm in size, while SD-C60 as an individual structure is 1030 nm in size. The aforementioned methods showed that SD-C60 contains water layers, which explains the difference between those two structures in the physicochemical properties, and their effects on biomolecules. (4) Conclusions: Based on the above methods and techniques, FD-C60 and SD-C60 are two different substances in terms of size, structure, and physicochemical properties; FD-C60 at 100C has endothermic characteristics and SD-C60 at 133C has exothermic characteristics, FD-C60 possesses water molecules only from humidity, while SD-C60 has water molecules from both humidity and extra water molecules in layers, the zeta potential of FD-C60 is -25.85 mV, while it is -43.29 mV for SD-C60.

Half-metallic semi-Heusler compounds are currently at the forefront of scientific research due to their potential applications in spintronic devices. Unlike other semi-Heuslers, the p0(d0)-d compounds do not appear to crystallize in the typical variant of the C1b structure. We investigate this phenomenon in the p0-d Heusler compounds LiYGa and LiYGe, where Y varies between Ca and Zn, using first-principles ab-initio electronic band structure calculations. We examine the electronic and magnetic properties of these compounds in relation to the three possible C1b structures. Notably, LiVGa, LiVGe, LiMnGa, and LiCrGe are half-metallic ferromagnets across all three variations of the C1b lattice structure. Our findings will serve as a foundation for future experimental studies on these compounds.

SARS-CoV-2 is a novel and highly pathogenic coronavirus, which was first diagnosed in Wuhan city, China, in 2019, and spread to 185 countries and territories, and as of April 29, 2020, more than 3.11 million cases were recorded, and more than 217,000 people were killed. Despite all worldwide efforts, there is currently no vaccine, any drugs available to protect people against deadly SARS-CoV-2 coronavirus. The world urgently needs a SARS-CoV-2 coronavirus vaccine or effective antiviral drugs to relieve the human suffering associated with the pandemic that kills thousands of people every day. The SARS-CoV-2 genome encode a non-structural proteins named as ORF1a/b, and structural proteins such as spike (S) glycoprotein, nucleocapsid protein (N), small envelop protein (E) and matrix protein (M). A number of studies have been shown that CoV spike (S) glycoprotein and nucleocapsid protein (N) could be promising targets for vaccine, antibodies and therapeutic drug development to combat with deadly, pandemic SARS-CoV-2. Purposes of the present paper is the sequence analysis and amino acid variations of structural proteins deduced from novel coronavirus SARS-CoV-2 strains, isolated in different countries. Multiple sequence alignment of S, N and E proteins from four different coronavirus species, are also described. It is expected that the data from these studies will be very useful for the the designing and development of vaccines, antibodies and therapeutic agents that can be used to combat with the highly pathogenic SARS-CoV-2 coronavirus worldwide.

During December 2019, a novel coronavirus named SARS-CoV-2 has emerged in Wuhan, China. The human to human transmission of this virus has also been established. The virus has so far infected more than 2 million people and spread over 200 countries. The World Health Organization (WHO) has declared COVID-19 a global health emergency due to its spread well beyond China. It has been established that this virus originates from bats and uses an intermediate host for transfer to humans. The knowledge about the intermediate host is important to find the virus shuttle mechanism to stop future outbreaks. For this, the genetic and structural analysis of coronaviruses spike proteins was performed using a computer-assisted approach.To conduct the In silico analysis, 43 sequences of spike protein belong to different species were retrieved from the NCBI nucleotide database. Pairwise and multiple sequence alignments were performed to check the similarities and differences of the retrieved sequences. Moreover, to highlight relationships among different species, phylogenetics analysis was performed using the MEGA software tool. In the end, protein structure alignment (superimposition) was performed against the reference structure by UCSF Chimera software. The results highlighted that the maximum similarity of human protein was found against Bat and Pangolinsequences. Moreover, among Bat and Pangolin, the highest similarity was found against pangolin based on phylogenetics analysis. These results suggest that SARS-CoV-2 transfers from bats to humans through pangolins.

We do this research to investigate the relationship between renewable energy, public health expenditure, logistics performance indices, and economic and environmental sustainability in the ASEAN member states, through the analysis of a panel data from 2007 to 2017. The study used secondary data, which is downloaded from the World Bank Website and employs SEM (Structural Equation Modelling) model for testing hypothesis. The results show that the usage of renewable energy in logistical operations would enhance the environmental and economic performance in terms of mitigating carbon emissions and greenhouse gas emissions. While, public health expenditure and environmental performance is negatively correlated, which confirms that greater environmental sustainability with lower carbon emissions and greenhouse gases will improve human health and economic growth. Moreover, greater public health expenditure and poor environmental performance has negative effect on economic growth, inefficiency and low productivity of labor slowdown to the economic activities. For another side, the usage of renewable energy and the adoption of green practices in international logistics will develop the environmental sustainability, establish better image of a country and attract foreign direct investment inflows, and also minimize carbon emissions and public health expenditure, spurring sustainable economic growth with better export opportunities in pro-environmental countries.

Influence of water concentration on the properties of fluorine-doped tin oxide (FTO) thin films was systematically studied in this work. Home made SISOM’s SPEED techniques and its chemical formulation was employed to grow the FTO on quartz substrate. Water concentration in the precursor solution was varied from 0, 0.5, 1.0 and 1.5 mol %. The structural, optical, and electrical properties of the films were studied under these deposition conditions. The results show that the properties of the films varied significantly with water concentration. Scanning electron microscopy (SEM) revealed FTO films whose grain size and uniformity increases significantly with increase in water concentration. The structure of the films was measured by X-ray diffraction (XRD) measurement. It shows polycrystalline films with (110), (101), (200), (211) and (220) orientation; the strength increases as water concentration increases. The optical transmission was determined by UV-Vis spectroscopy at 380–780 nm UV-VIS regions. The optical transmittance varies with water concentration with an average of 84%. The electrical property, measured by Hall Effect revealed n-type semiconductor. The films have the following properties: resistivity, 15 × 10^-4Ω cm; carrier concentration, 18.7 × 10¹⁹ cm^-3 and mobility of 21.86 cm² V^-1 s^-1. The average figure of merit, φ of the FTO film is 1.25. Optimum deposition condition was established after series of experiments and was found to be 1.5% water concentration at 460^oC substrate temperature. The FTO films deposited in this work could be a promising replacement to indium tin oxide (ITO) especially in dye-sensitized solar cells.

The conservation of the main protease in viral genomes, combined with the absence of a homologous protease in humans, makes this enzyme family an ideal target for developing broad-spectrum antiviral drugs with minimal host toxicity. GC-376, a peptidomimetic 3CL protease inhibitor, has shown significant efficacy against coronaviruses. Recently, a GC-376-based PROTAC was developed to target and induce the proteosome-mediated degradation of the dimeric SARS-CoV-2 3CLPro protein. Extending this approach, the current study investigates the application of the GC-376 PROTAC to the 3CPro protease of Enteroviruses, specifically characterizing its interaction with CVB3 3CPro through X-ray crystallography, NMR and biophysical techniques. The present structural data show that there are some changes between the binding of CVB3 3CPro and SARS-CoV-2 3CLPro, but the overall similarity is strong. The most notable variation is the orientation of the phenylmethyl ester of GC-376 with the S4 subsite of the proteases. This is linked to the flexibility of the protein structure around the region of the catalytic triad shown by our NMR data. Other structural variations include distinct ligand interactions in subsites S1 and S2, influenced by the presence of Glu71 in CVB3 3CPro. Despite these differences, the GC-376 PROTAC fits well within the binding sites of both proteases, demonstrating its potential as a broad-spectrum antiviral agent.

Background: Arthroscopic revision rotator cuff repair (ARRCR) is challenging. Biologic strategies seem to be promising. The aim was to evaluate the effectiveness of combination of microfractures of the greater tuberosity, augmentation with collagen patch graft, and platelet concentrate injections in ARRCR. Methods: A retrospective comparative study was conducted on patients that underwent ARRCR with minimum two-years follow-up. Patients in the augmentation group underwent ARRCR combined with microfractures, collagen patch graft, and postoperative subacromial injections of platelet concentrate. A standard rotator cuff repair was performed in the control group. Primary outcome: Constant Murley score (CMS). Secondary outcomes: disease-specific health-related quality of life by using the Disabilities of the Arm, Shoulder and Hand (DASH) score; assessment of tendon integrity with magnetic resonance at least six months after surgery. Significance was set at p < 0.05. Results: Forty patients were included. Mean follow-up was 36.2 + 8.7 months. The mean CMS was greater in the augmentation group (p = 0.022). No differences could be found for DASH score. Healing failure rate was higher in the control group (p = 0.002). Conclusion: Biologic augmentation of ARRCR by combination of microfractures, collagen patch graft and subacromial injections of platelet concentrate is an effective strategy in improving tendon healing rate.

Introduction: Patients’ satisfaction was extensively researched over the last decades, given its role in building loyalty, compliance to treatment, prevention, and eventually higher levels of wellbeing and improved health status. Patients’ feedback on the perceived quality of health services can be incorporated into practice; therefore, understanding factors and mechanisms responsible for patients’ satisfaction allows providers to tailor targeted interventions. Method: A questionnaire assessing patients’ perception of the quality of health services was administered to a country-representative sample of 1500 Romanian patients. Using a partial least squares—path modeling approach (PLS-PM), with cross-sectional data, we developed a variance-based structural model, emphasizing the mediating role of trust and satisfaction with various categories of health services. Results: We confirmed the mediating role of trust in shaping the relationship between the procedural accuracy of health professionals, along with the perceived intensity of their interaction with patients, and patients’ experienced quality of the health services. We confirmed the mediating role of satisfaction by the categories of services in the relationship between waiting time on the premises, attention received, and the perceived reliability of the information received, as predictors, and the experienced quality of the health services. In addition, indirect assessment of patients’ satisfaction is a good predictor for direct assessment, thereby affirming the idea that the results of the two types of evaluations converge. Discussions: One of the most efficient solutions to increase both patients’ satisfaction and their compliance is to empower the communication dimension between patients and health practitioners. Given the non-linear relationships among variables, we advocate that, unless the nature of the relationships between satisfaction and its predictors is understood, practical interventions could fail. The most relevant variable for intervention is the degree of attention patients perceive they received. We suggest three methods to turn waiting time into attention given to patients.

Rett syndrome (RTT) is mainly caused by mutations in methyl CpG-binding protein 2, cyclin-dependent kinase-like 5, or forkhead box protein G1. These RTT-causing proteins harbor an intrinsically disordered region (IDR) whose conformation exhibits spatiotemporal heterogeneity, which not only confer versatility to the protein, but also implicates them in diseases. The IDR generally evolves more rapidly than an ordered structure. In this study, we examined the relationship between pathogenic RTT-associated point mutations in RTT-causing proteins and the evolutionary dynamics of sequence features including structural order–disorder, phosphorylation sites, and evolutionary rates. We also analyzed the molecular properties and evolution of proteins that interact with RTT-causing proteins in terms of phylogenetic profiles, tissue specificity, subcellular localization, expression level, and functions. The results indicate that constrained IDRs may function by forming contacts with other regions in the protein sequence causing pathogenic missense mutations likely to arise in the rapidly evolving IDR and affect molecular networks, leading to disease. The results also provide novel insights into the genetic basis for RTT and the evolution of the neocortex in higher vertebrates.

A solution is presented that describes a region of space, box or warp bubble, where time gets slowed down by an arbitrary factor, while reducing the components of the energy-impulse tensor by any chosen amount.

This article investigates the vibration analysis of the mast on the bridge top of a 28-meter tugboat, in the quasi-static regime. The study aims to determine the natural frequencies using an equivalent dynamic model of the mast and considers the accelerations of different degrees of freedom of the vessel. Practical design and reinforcement strategies for the local bridge top structure are proposed, utilizing numerical and analytical tools. The investigation explores various alternatives to optimize the structural arrangement. By analyzing the modal behavior, insights are provided for efficient design and reinforcement. The results contribute to understand the mast's vibration characteristics, offering guidance for similar structures. The study employs numerical and analytical methods, enhancing the optimization of the mast's behavior. It determines natural frequencies, proposes practical design strategies, and explores alternatives for structural optimization. The findings provide insights for shipbuilding and mast design applications in other vessels and industries such as radar mast, compass deck and guyed mast.

The R23Cu7Mg4 (R = Ca, Eu) intermetallics, studied by single crystal X-ray diffraction, were found to be isostructural with the Yb23Cu7Mg4 prototype (hP68, k4h2fca, space group P63/mmc), forming a small group inside the bigger 23:7:4 family, otherwise adopting the hP68-Pr23Ir7Mg4 crystal structure. The observed structural peculiarity is connected with the divalent character of the R component and with a noticeable volume contraction, resulting in a clear clustering of title compounds inside the whole 23:7:4 family. The occurrence of fragments typical of similar compounds, particularly Cu-centered trigonal prisms and Mg-centered core-shell polyicosahedral clusters with R at vertices, induced the search of significant structural relationships. In this work, a description of the hexagonal crystal structure of the studied compounds is proposed as a linear intergrowth along the c-direction of the two types of slabs R10CuMg3 (parent type: hP28-kh2ca, SG 194) and R13Cu6Mg (parent type: hR60-b6a2, SG 160). The ratio of these slabs in the studied structure is 2:2 per unit cell, corresponding to the simple equation 2XR10CuMg3 + 2XR13Cu6Mg = 2XR23Cu7Mg4. This description assimilates the studied compounds to the (Ca,Eu,Yb)4CuMg ones, where the same slabs (of p3m1 layer symmetry) are stacked in a different way/ratio, and constitutes a further step towards a structural generalization of R-rich ternary intermetallics.

An analysis of the stiffness theory reveals that coal mass compression bumps occur only when both the failure criterion and the stiffness criterion are simultaneously satisfied. Then a new structural factor called uneven stiffness coal seam structure (USCS) is proposed, which consists of an uneven stiffness coal seam along with continuous roof and floor. The USCS serves the dual functions of pressure concentration and stiffness reduction. The former facilitates stress concentration from the low stiffness zone (LSZ) to the high stiffness zone (HSZ), thus raising the risk (rF) of failure. The latter reduces the stiffness of the surrounding rock of the HSZ, allowing the system to meet the stiffness criterion even with a hard roof, thereby reconciling the contradiction between the stiffness theory and engineering experience and raising the risk (rI) of instability. The HSZ of the USCS, including thinning zones, bifurcating areas, magmatic intrusion areas, and remnant pillar affected areas, is more susceptible to coal bump incidents than a conventional coal seam. Mechanical analysis and simple numerical simulations validate the pressure concentration and stiffness reduction functions of the USCS. The results demonstrate the following: 1) The normal stress of the HSZ positively correlates with ER, HR, KH, and SL, but negatively correlates with KL and SH; The stiffness of surrounding rock of the HSZ negatively correlates with HR, KH, SL, and SH, but positively correlates with ER and KL. 2) Failures within the HSZ of the USCS enables the roof strata to release bending deformation energy without undergoing fracturing. 3) The alignment between the HSZ of an existing USCS and the HSZ of an artificial USCS advancing with the working face intensifies stress concentration and reduces stiffness, thereby significantly increases the risk (rCB) of coal bump. By applying the stiffness theory and relevant USCS findings, new explanations can be provided for engineering phenomena such as the time-delayed coal bumps, the inefficient pressure relief in ultra thick coal seams, and the “microseism deficiency” observed prior to certain coal bumps.

Despite air pollution being a leading cause of health issues in developing nations, public awareness and understanding of local air quality remains notably low. The present study assesses the perception, attitude, and environmental knowledge of local air pollution among adult urban residents (n=870) in a city with leading air pollution rates among cities of emerging economies: Astana, Kazakhstan. Structural equation modeling (SEM) was employed to investigate the causal relationship between perceived air quality, environmental literacy, and willingness to pay (WTP) for environmental protection. Findings indicate over 40% of residents neither consider the city being highly polluted nor recognize the association between air quality and adverse health outcomes, correlated with a generally low level of environmental literacy. The age, education, and health status of the participants significantly affected (p&lt;.001) their level of environmental knowledge and awareness. The SEM analysis indicates that knowledge is the major determinant in improving public awareness and perception of local air pollution (path value=0.626). Moreover, a close association between WTP and environmental attitude was also evident (path value=0.533). The findings of the present study may provide valuable insights for healthcare professionals, environmental researchers, and governmental institutions for implementing more effective public interventions to protect local air quality.

Recently, there has been remarkable progress in the development of smart textiles, especially knitted strain sensors, to achieve reliable sensor signals. Stable and reliable electro-mechanical properties of sensors are essential for using textile-based sensors in medical applications. How-ever, challenges associated with significant hysteresis and low gauge factor (GF) values remain for using strain sensors for motion capture. To evaluate these issues, a comprehensive investiga-tion of the cyclic electro-mechanical properties of weft-knitted strain sensors was conducted in the present study to develop a drift-free elastic strain sensor with a robust sensor signal for mo-tion capture for medical devices. Several variables were considered in the study, including the variation of the basic knit pattern, the incorporation of the electrically conductive yarn, and the size of the strain sensor. The effectiveness and feasibility of the developed knitted strain sensors are demonstrated through experimental evaluation, by determining the gauge factor, its non-linearity, hysteresis and drift. The developed knitted piezoresistive strain sensors have a GF of 2.4, a calculated drift of 50 %, 12,5 % hysteresis, and 0.3 % nonlinearity in parts.

The present study illustrates the strong effect of geometrical parameters on the magneto-structural properties of Co2MnSi glass-coated microwires prepared using the Taylor-Ulitovsky method. Thus, two samples with different geometrical aspect ratios (ρ= d / D) have been fabricated, where d is the metallic nuclei diameter and D is the total diameter of the Co2MnSi microwire. The XRD analysis shows a significant change by modifying the aspect ratio, for ρ = 0.46 the main peak with miller indices (220) is recognized as an A2-type disordered cubic structure. Meanwhile, in the sample with a low aspect ratio, ρ = 0.31, the perfect L21 ordered cubic structure is attained. In addition, a decrease in average grain size from 36.62 nm to 28.07 nm by increasing the aspect ratio from 0.46 to 0.31 is observed. The magnetic characterization has been done in a wide range of temperatures and magnetic fields. Both of Co2MnSi samples show ferromagnetic behavior in a whole measuring temperatures range. A significant increase in coercivity and normalized reduced remanence by decreasing the aspect ratio is observed. The change in the magnetic properties is attributed to the modification in the microstructure, which is induced during the fabrication process. Such a dependence on the microstructure and magnetic properties on the ρ-ratio can be associated either with the internal stresses distribution and magnitude or with different quenching rates of microwires with different aspect ratios. The current findings demonstrate the tunability of microstructure and magnetic properties of Co2MnSi-glass-coated microwires simply, by a small modification in the geometric properties during the manufacturing process and without excreting any additional post-processing. The variation in geometric parameters of Co2MnSi glass-coated microwires allows us to tune magnetic properties and structure, which is essentially advantageous for sensing devices development.

The structural stability of γ-boron is investigated using Raman spectra under high pressures up to 126 GPa at ambient temperature. The pressure dependence of all the Raman-active modes of the γ-boron is reported. We also observe amusing changes within the B3g and B1g Raman-active vibrational modes, which results in the phenomenon of merging first and then separating of the Raman peaks. In addition to the Raman measurements, the changes in crystal structure and force constants are calculated to reasonably explain the discrepancy between the two Raman modes in response to pressure. The results of the continuous shifts for all Raman modes with increasing pressure indicate that γ-boron remains stable below this pressure value, with no changes in either symmetry or structure.

Searching for bioactive compounds within the huge chemical space is like trying to find a needle in a haystack. Isatin is a unique natural compound which is endowed with different biopertinent activities specially in cancer therapy. Herein, we envisaged that adopting a hybrid strategy of isatin and α,β-unsaturated ketone would afford new chemical entities with strong chemotherapeutic potential. Of interest, compounds 5b and 5g demonstrated significant antiproliferative activities against different cancer genotypes according to NCI assay. Concomitantly, their IC50 against HL-60 cells were 0.38 ± 0.08 and 0.57 ± 0.05, respectively, demonstrating remarkable apoptosis and mod-erate cell cycle arrest at G1 phase. Intriguingly, an impressive safety profile for 5b was reflected by a 37.2 times selectivity against HL-60 over PBMC from a healthy donor. This provoked us to further explore their mechanism of action by in vitro and in silico tools. Conclusively, 5b and 5g stand out as strong chemotherapeutic agents that hold a clinical promise against acute myeloid leukemia.

This paper deals with the structural decomposition input-output for the economic analysis of agriculture, forestry and fishing in six EU-28 countries (Austria, Belgium, France, Germany, Italy and Spain) in the 2010-2015 period. The objective is to determine the causes of changes in production in these sectors with a particular focus on disaggregation technological change by distribution factors associated with a specific normalisation of the Leontief inverse. In calculating the net multipliers, an attempt was made to exclude sectors' own consumption appropriately. However, the treatment of own consumption upon introducing a time factor requires further investigation to avoid questionable quantifications. In general, typical characteristics of primary sectors include the accumulation of a significant amount of their own consumption, facilitated by symmetric accounting. Therefore, attention is drawn to these sectors so as to reveal possible analysis techniques that will provide nuance or validate existing techniques.

One notable features of the SARS-CoV-2 genome is that the spike protein of SARS-CoV-2 has a functional polybasic (furin) cleavage site (RRAR) at the S1–S2 boundary through the insertion of 12 nucleotides encoding PRRA. To date, the furin cleavage site (FCS) remains an experimentally uncharted territory both structurally and functionally. For instance, whether or not FCS is actually cleaved, before or after viral cell entry or exit, still remains to be experimentally investigated. With currently available structural data, this article presents a computational structural characterization of the FCS inserted into SARS-CoV-2 spike glycoprotein, and puts forward a set of structural hypothesis against the hypothesis of SARS-CoV-2 from purposeful manipulation: (1), the inserted FCS does not alter, neither stabilize nor de-stabilize, the overall structure of SARS-CoV-2 spike glycoprotein; (2), the net structural consequence of FCS is the insertion of a furin cleavage site into SARS-CoV-2 spike glycoprotein, whose S1 and S2 subunits will still be bonded together even if the FCS is actually cleaved by furin protease.

Water inrush from coal floor constitutes one of the main disasters in mine construction and mine production, which always brings high risks and losses to the coal mine safe production. As the mining depth of coal fields in North China gradually increased, especially in the complicated structural region, the threat posed by limestone karstic water of coal floor to the safe stoping of mines has become increasingly prominent. In this paper, the Taoyuan coalmine was taken as an example, for which, the directional borehole grouting technology was utilized to reinforce the coal seam floor prior to mining. Also, the factors affecting the grouting effect were analyzed. These were the geological structure, the crustal stress and the range of slurry diffusion. The layout principle of grouting drilling was put forward and the directional drilling structure was designed. The water level observations in the end hole indicated that the target stratum was accurate and reliable. The effect of grouting was validated through the audio frequency electric perspective method and the holedrilling in the track trough. The results demonstrated that the effect of grouting in third limestone and the rock stratum above the third limestone of coal seam floor was apparent. Simultaneously, no water inrush occurred following the actual mining of the working face, which further demonstrated that the grouting reinforcement effect was apparent. The research findings were of high significance for the prevention and control of floor water disaster and water conservation in deep complex structural areas.

Samples of mortar mixtures were prepared substituting the cement Portland (CPC-30R) by 0 (standard), 10 and 15% of fly ash and the structural evolution and compressive strength at 3, 7, 14 and 28 days were determined. The results for standard mortar samples showed the mineralogi-cal species portlandite, calcite, ettringite, iron oxide, silicon oxide and sillimanite. Magnetite was identified in the mixtures of mortars with portland cement substitution by 10% and 15% fly ash. The peaks corresponding to the portlandite, and ettringite showed an increase in their intensities with increasing curing time attributed to the consolidation of mineral species. The SEM tech-nique results showed that the mortar samples without fly ash addition contained mainly port-landite and ettringite while the samples with cement substitution by 10 and 15% of fly ash at 28 days further contained particles of fly ash coated with portlandite and ettringite, particles with a smooth surface and particles of fly ash with signs of attack on its surface. An increase inc was observed when the age of the mortar and the substitution of Portland cement by fly ash were increased from 3 to 28 days and from 0 to 15% respectively. The maximum value of c was reg-istered for the mortar sample with Portland cement substitution by 15% fly ash at 28 days of curing with 17.38 Mpa.

The recent demand for reducing pollutant and CO2 emissions from internal combustion engines has created an urgent need for the development of ultra-lean burn engines that ensure combus-tion stability and reducing knocking tendency. One of the most promising methods is the Pre-chamber Spark Ignition (PCSI) system, where a jet of high-energy reactive gases, produced by pilot combustion in a pre-chamber, ignites the main combustion event in the cylinder. Given the intricate phenomena inherent to PCSI systems, conducting 3D CFD studies is imperative for a comprehensive analysis and optimal design. Furthermore, the detailed CFD model, combined with the calibrated 0-D/1-D model, is anticipated to yield a significant amount of new data that would be difficult to obtain through experimental approaches, making it essential for advancing our understanding and optimization of these systems. However, recently published papers re-port that some state-of-the-art models developed for conventional SI operation may not be pre-dictive under the challenging conditions of TJI systems, particularly under lean conditions. This review elucidates the reasons behind the widespread adoption of CFD in the optimal design of PCSI engines. It presents significant examples and delves into the potential and challenges of employing CFD not just as a predictive tool but also as a design instrument for enhancing PCSI engine performance.

In reinforced concrete (RC) structures, splicing is required owing to the length limitations of rebars, insufficient lengths, and transportation issues. In particular, splices connect the rebar of RC structures such as walls, columns, beams, slabs, and joints. Lap splices are the most commonly used method worldwide because they do not require specific equipment or skilled workers. However, lap splices incur high construction costs because of the long splice lengths required for large-diameter rebars in megastructures, as well as issues pertaining to material supply, labor costs, constructability, and project duration. Additionally, approximately 15% more rebar is required because of the overlap. Energy saving for a sustainable built environment is possible if the disadvantage of lap splices, which generate high CO2 emissions due to the excessive use of rebar, are resolved. Hence, mechanical rebar couplers (MRCs) have been developed. However, despite their advantages, they have not been widely applied in construction sites owing to concerns regarding safety, quality, and constructability. Although various MRCs have been developed, most studies focus only on their structural performance. Therefore, a data-driven approach for selecting MRCs based on the reinforcing bar shape and structural characteristics is proposed in this study. Using a data-driven MRC selection algorithm, using the T-threaded coupler for one rebar over two floors resulted in 56% more efficient labor productivity, 15% shorter assembly time, 17% lower costs, and 26% lower CO2 emission. Using a developed algorithm, the appropriate MRC can easily and rapidly be selected for frequent design changes.

As a key mediator of chronic pain, neurotrophin nerve growth factor (NGF) binds to two neurotrophin receptors: p75 neurotrophin receptor (p75NTR) and tyrosine kinase receptor A (TrkA). The formation of the p75NTR-NGF-TrkA complex is implicated in the potentiation of chronic pain signals, making it an attractive target for therapeutic explorations. NGF analogues and monoclonal antibodies (mAbs) targeting NGF represent two distinct approaches in modulating the intricate signaling pathways involved in pain transduction mediated by the p75NTR-NGF-TrkA complex. While NGF analogues offer the advantage of tailored design to fine-tune neurotrophic responses, monoclonal antibodies provide a more systemic and comprehensive blockade of NGF, inhibiting its interactions with both p75NTR and TrkA receptors. However, the use of mAbs may pose challenges related to potential side effects and interference with the physiological functions of NGF. As a result, balancing the benefits and drawbacks of the two approaches is critical for advancing therapeutic strategies towards the alleviation of p75NTR-NGF-TrkA-mediated pain. In this study, therefore, a novel structural and biophysical approach was employed for the design of NGF analogues to suppress p75NTR-NGF-TrkA-related chronic pain signaling. Employing high-throughput structural modeling and biophysics-based intermolecular binding affinity calculations, this article for the first time puts forward a set of NGF analogues, including in particular NGF analogues with four site-specific mutations, for whose dimerizations the K d at 37 ^◦C were reduced by three orders of magnitude (from 10^-9 M to 10^-6 M) compared to the K d at 37 ^◦C for the dimerization of native NGFs. Overall, the integration of structural and biophysical perspectives enhances our understanding of the rational design of NGF analogues as promising candidates for the development of NGF-targeted analgesic therapies, which balances the benefits and drawbacks of anti-NGF antibodies and NGF analogues for advancing therapeutic strategies towards the alleviation of p75NTR-NGF-TrkA-mediated pain.

In this paper, based on the symmetrical reliability theory, a research method for the safety factor of overall overturning stability of continuous beam bridge under carbon fiber reinforced polymers (CFRP) during cantilever and horizontal rotation construction is proposed. Under the premise that the given target reliability index is known, the method solves the overall overturning stability safety factor of continuous beam bridge under carbon fiber reinforced polymers during cantilever and horizontal rotation construction by using the symmetrical reliability analysis theory and considering the randomness of structural parameters. This method is used to calculate the safety factor and the design reinforcement aera of CRFP of overturning stability and the design reinforcement aera of CRFP of a continuous beam bridge, and the parameters are analyzed. The calculation results show that the randomness of parameters will have a great impact on the overall safety factor and the CRFP aera of overturning stability of cantilever and horizontal rotation construction of continuous beam bridge, and ignoring the influence of randomness of parameters will lead to overestimation of the overall safety factor and underestimation of the CRFP aera of overturning stability of cantilever and horizontal rotation construction of continuous beam bridge.

Abstract Peripartum depression (PPD) is a major complication of pregnancy and many risk factors have been associated with its development, including dysfunctional coping strategies and insecure attachment styles, both during pregnancy and postpartum. The aim of our study was to investigate the role of coping strategies in mediating the relationship between women’s attachment style and PPD in pregnancy, and one week after childbirth, in a large cohort of women. We hypothesized that the relationship between anxious and avoidant attachment and PPD would be mediated by use of maladaptive coping strategies. The assessment instruments were Edinburgh Postnatal Depression Scale (EPDS), Brief Coping Orientation for Problem Experiences (COPE), Experiences in Close Relationship Scale (ECR). The results indicated that the effect of insecure attachment styles (anxious and avoidant attachment) on antepartum depressive symptomatology was partially mediated by dysfunctional coping styles. Anxious attachment has also an indirect significant effect on postpartum depression through emotional coping; however, avoidant attachment does not seem to be significantly related to postpartum depression. Our findings revealed that not only it is important to consider attachment in understanding PPD but also that coping plays an important role in these relationships. These findings would help a preventive coping-based intervention strategy to enhance the capacity of women with insecure attachment styles to use more adaptive coping during and after pregnancy.

The emergence of drug-resistant parasitic nematodes of both humans and livestock calls for development of alternative and cost-effective control strategies. For the economically important ruminant strongylid Haemonchus contortus, Barbervax® remains the only registered vaccine available. Here we compared the microbiome, genome-wide diversity and transcriptome of H. contortus adult male populations that survived vaccination with an experimental vaccine after inoculation in sheep. Our genome-wide SNP analysis revealed 16 putative candidate vaccine evasion genes. However, we did not identify any evidence for changes in microbial community profiling based of 16S rRNA gene sequencing results of vaccine surviving parasite populations. A total of 58 genes were identified as significantly differentially expressed with six being long non-coding (lnc) RNAs and no putative candidate SNP associated genes. The genes highly upregulated in surviving parasites from vaccinated animals were associated with GO terms belonging to predominantly molecular function and a few biological processes that may have facilitated evasion or potentially lessened the effect of the vaccine. These included five targets: astacin (ASTL), carbonate dehydratase (CA2), phospholipase A2 (PLA2), glutamine synthetase (GLUL) and fatty acid-binding protein (FABP3). We searched all five DEG targets against the proteomes of selected Nematoda (Clades III, V, IV, C, I) and Platyhelminthes (Clades Monogenea, Trematoda, Cestoda, Rhabditophora) to determine homologs within the H. contortus NZ_HCO_NP v1.0 genome and identified single-copy orthologous groups (OGs) in selected proteomes. All but one (FABP3) demonstrated high levels of duplication and wide-spread occurrence in closely related Caenorhabditis elegans and Pristionchus pacificus, with complete absence of all five gene targets among other Clade III (Toxocara canis) and V (Ascaris suum, Ascaris lumbricoides and Parascaris univalens) nematodes, further supporting their vital biological functions in nematodes. Phylogenetic analyses inferred the presence of only ASTL and CA2 in almost all Nematoda, platyhelminthes and metazoans examined, with loss of GLULs observed among all outgroup vertebrate species and the presence of FABP3 in only three other species (Schmidtea mediterranea, Fasciola gigantica and F. hepatica). Our tertiary structure predictions and modelling analyses were used to perform in silico searches of all published and commercially available inhibitor molecules or substrate analogues with potential broad-spectrum efficacy against nematodes of human and veterinary importance.

The presence of a non-structural protein 1 (NS1) in tick-borne encephalitis (TBE) vaccines and the possible induction of an NS1-specific immune response in vaccinated individuals remains a somewhat controversial topic. Previously, we detected the presence of NS1 in Encepur TBE vaccine by mass spectrometry and found the induction of NS1-specific IgG antibodies in mice vaccinated with FSME-Immun TBE vaccine. Here, in this follow-up study, we examined the dynamics and extent of the NS1-specific IgG response in mice vaccinated with these two vaccines in more detail and compared it with the IgG response to the whole virus (WV). Mice were vaccinated at two-week intervals with a total of six doses of each vaccine, and levels of IgG antibodies to TBE virus WV and NS1 were measured by ELISA after each dose. Both vaccines elicited a robust anti-WV IgG response after two doses. The Encepur vaccine did not elicit NS1-specific IgG even after all six doses. In contrast, FSME-Immun vaccine triggered production of NS1-specific IgG after four doses. The results indicate that FSME-Immun is the only vaccine that elicits an NS1-specific antibody response in mice. However, compared to WV-specific IgG, the NS1-specific response is weaker, and a higher number of doses is required to induce detectable levels of NS1-specific IgG antibodies.

Favipiravir is a broad-spectrum inhibitor of viral RNA-dependent RNA polymerase (RdRp) currently being used to manage COVID-19 in several countries. By acting as a substrate for RdRp, favipiravir gets incorporated into the nascent viral RNA and prevents strand extension. A high mutation rate of SARS-CoV-2 RdRp may facilitate antigenic drift as an answer to the host immune response, thereby generating resistance of virus to favipiravir. Therefore, it is extremely crucial to predict potential mutational sites in the RdRp and the emergence of structural modifications contributing to drug resistance. Here, we used high-throughput interface-based protein design to generate >100,000 designs and identify mutation hotspot residues in the favipiravir-binding site of RdRp. Several mutants had lower binding affinities to favipiravir, out of which hotspot residues with a high propensity to undergo positive selection were identified. The results showed that the designs retained an average of 97 to 98% sequence identity, suggesting that SARS-CoV-2 can develop favipiravir resistance with just a few mutations. Notably, we observed that out of 134 mutations predicted designs, 63 specific mutations were already present in the CoV-GLUE database, thus attaining ~47% correlation match with the clinical sequencing data. The findings improve our understanding of the potential signatures of adaptation in SARS-CoV-2 against favipiravir and management of COVID-19. Furthermore, they can help develop exhaustive strategies for robust antiviral design and discovery.

We analyzed the SARS-CoV-2 spike (S) protein amino acid sequence extracted from 11,542 viral genomic sequences submitted to the Global Initiative on Sharing All Influenza Data (GISAID) database through April 27, 2020. Consistent with prior reports, we found a major S protein mutation, D614 to G614, that was represented in 56% of all the analyzed sequences. All other mutations combined were less than 10%. After parsing the data geographically, we found most of the Chinese patient samples showed D614 (97%). By contrast, most patient samples in many European countries showed G614 (51 to 88%). In the United States, the genotypic distribution in California and Washington was similar to Asian countries, while the distribution in other US states was comparable to Europe. We observed a dramatic increase in the frequency of G614 over time in multiple regions, surpassing D614 when both were present, suggesting G614 S protein virus outcompetes D614 S protein virus. To gain insight into the consequences of the D614G mutation, homology modeling using a multi-template threading mechanism with ab initio structural refinement was performed for a region of the S protein (S591 to N710) spanning the D614G mutation and the S1 furin cleavage site. Molecular models of this region containing D614 or G614 revealed a major difference in secondary structure at the furin domain (RRARS, R682 to S686). The D614 model predicted a random coil structure in the furin domain whereas the G614 model predicted an alpha helix. Critical residues in the cleavage domain of G614 model were found to better align with the PDB structure of a furin inhibitor. Thus, homology modeling studies suggest a potential mechanism whereby the D614G mutation may confer a competitive advantage at the furin binding domain that may contribute to the rise of the D614G SARS-CoV-2 mutant.

Vaccination against tick-borne encephalitis (TBE) is based on the use of formalin-inactivated, culture-derived whole-virus vaccines. Immune response following vaccination is primarily directed to the viral envelope (E) protein, the major viral surface antigen. In Europe, two TBE vaccines are available in adult and pediatric formulations, FSME-IMMUN® (Pfizer) and Encepur® (GlaxoSmithKline). Herein, we analyzed the content of these vaccines using mass spectrometry (MS). The MS analysis revealed that the Encepur vaccine contains not only proteins of the whole virus particle, but also viral non-structural protein 1 (NS1). MS analysis of the FSME-IMMUN vaccine failed due to the high content of human serum albumin used as a stabilizer in the vaccine. However, the presence of NS1 in FSME-IMMUN was confirmed by immunization of mice with six doses of this vaccine, which led to a robust anti-NS1 antibody response. NS1-specific western blot analysis detected anti-NS1 antibodies also in sera of humans who received multiple doses of either of these two vaccines; however, most vaccinees who received ≤3 doses were negative for NS1-specific antibodies. The contribution of NS1-specific antibodies to protection against TBE was demonstrated by immunization of mice with purified NS1 antigen, which led to a significant (p < 0.01) prolongation of the mean survival time after lethal virus challenge. This indicates that stimulation of anti-NS1 immunity by the TBE vaccines may increase their protective effect.

The role of human resource management practices and organizational loyalty dealing with employee retention has been widely explored and examined in the existing literature. The majority of human resource management researchers have focused on the role of policies and practices in different sectors related to employee retention. However, less attention has been given to identifying the practices and procedures common across all industries and sectors. The present study attempts to determine and examine the most important constructs like HR practices and organizational loyalty of employee retention management and proposes a comprehensive structural equation model to measure the impact of these constructs on employee retention. After an extensive review of the literature, organizational loyalty, and human resources management practices like recruitment and selection, compensation and benefit, training and development, supervision and evaluation have been identified as four essential practices dealing with employee retention and are common across all industries. These practices constitute the component factors of an employee retention management predicting employee’s turnover intentions. The survey method was adopted, and the original data obtained through the self-administered questionnaire. The valid one hundred and eighty-nine (189) respondents analyzed by using Lisrel 8.7, Structural equation model (SEM) analysis results shows that human resource management practices and organizational loyalty have strong positive impact on employee retention. This study tends to assist human resource managers and decision makers in selecting the appropriate motivating factors to retain and satisfy their employees

The mass of a direct-drive generator is often defined by the requirements for structural stiffness to meet the magnetic stiffness between the rotor and stator surfaces. This paper analyses this magnetic stiffness and estimates the structural stiffness of direct-drive generators for different modes of deflection. The magnetic stiffness modelling is based on an analytical model of the airgap closing forces. The final models are verified using Finite Element analysis and carried out for both permanent magnet and wound rotor generators. It shows that wound rotor machines have higher stiffness requirements than permanent magnet machines. The structural stiffness of the generator rotor and stator are evaluated for different modes by applying spatially-varying forces and finding the associated deflections. Structural stiffnesses for the rotor, stator and bearing are then combined. Finally, the magnetic and structural stiffnesses are combined and a stiffness margin can be found. For the airgap not to close, this combined stiffness must be greater than 0. This method is applied to a relatively stiff and a relatively compliant set of generator structures in a case study in order to find the optimum and more sustainable configuration.

We studied Ni2FeSi, Co2FeSi and Co2MnSi -based full Heusler alloy glass-coated microwires with the same geometric aspect ratio ρ ≈ 0.50 ± 0.01 prepared using Taylor-Ulitovsky method. The fabrication of X2YZ; (X = Co &amp; Ni, Y = Fe &amp; Mn and Z = Si) based glass coated microwires with fixed aspect ratio is a quite challenging due to the different samples preparation conditions. The XRD analysis shows nanocrystalline microstructure for all the samples. Space group Fm3¯m (FCC) with disordered B2 and A2-types for Ni2FeSi and Co2FeSi and ordered L21-type for Co2MnSi are observed. The change in the positions of Ni, Co and Mn, Fe in X2YSi resulted in a variation in the lattice cell parameters and the average grain size of the sample. Room temperature magnetic behavior shows a dramatic change depending on the chemical composition, where Ni2FeSi-MWs shows the highest coercivity (Hc) compared to Co2FeSi-MWS and Co2MnSi-MWs. The Hc –value of Ni2FeSi-MWs is 16 times higher than that of Co2MnSi-MWs and 3 times higher than that of Co2FeSi-MWS. Meanwhile, the highest reduced remanence is reported for Co2FeSi-MWS (Mr =0.92), , being about 0.33 and 0.22 for Ni2FeSi-MWs and Co2MnSi-MWs, respectively. From the analysis of the temperature dependence of the magnetic properties (Hc and Mr) of X2YZ-MWs we deduced that Hc shows a stable tendency for Co2MnSi-MWs and Co2FeSi-MWs, meanwhile two flipped points are observed for Ni2FeSi-MWs where the behavior of Hc changes with temperature. For Mr monotonic increase by decreasing the temperature is observed for Co2FeSi-MWs and Ni2FeSi-MWs and roughly stable for Co2MnSi-MWs. The thermomagnetic curves at low magnetic field show irreversible magnetic behavior for Co2MnSi-MWs and Co2FeSi-MWs and regular ferromagnetic behavior for Ni2FeSi-MWs. The current result illustrates the ability to tailor the structure and magnetic behavior of X2YZ-MWs at a fixed internal stresses, i.e., with fixed aspect ratio. Additionally, a different behavior was revealed in X2YZ-MWs depending on the degree of ordering and elements distribution. The tunability of magnetic properties of X2YZ-MWs makes them suitable for sensing applications.

In this study, we considered the structural stability, electronic properties, and phonon dispersion of the cubic (c-ZrO₂), tetragonal (t-ZrO₂), and monoclinic (m-ZrO₂) phases of ZrO₂. We found that the monoclinic phase of zirconium dioxide is the most stable among the three phases in terms of total energy, lowest enthalpy, highest entropy, and other thermodynamic properties. The smallest negative modes were found for m-ZrO₂. Our analysis of the electronic properties showed that during the m–t phase transformation of ZrO₂, the Fermi level first shifts by 0.125 eV toward higher energies and then decreases by 0.08 eV in the t–c cross-section. The band gaps for c-ZrO₂, t-ZrO₂, and m-ZrO₂ are 5.140 eV, 5.898 eV, and 5.288 eV, respectively. Calculations based on the analysis of the influence of doping 3.23, 6.67, 10.35, and 16.15 mol. %Y₂O₃ onto the m-ZrO₂ structure showed that the enthalpy of m-YSZ decreases linearly, which accompanies further stabilization of monoclinic ZrO₂ and an increase in its defectiveness. The doping-induced and concentration-dependent phase transition of zirconium dioxide under the influence of yttrium oxide was studied, after which the position of the Fermi level changes and the energy gap decreases. It has been established that, not only for pure systems but including those doped with Y₂O₃, the main contribution to the formation of the conduction band is made by the p-states of electrons. The t-ZrO₂ (101) and t-YSZ (101) surface models were selected as optimal surfaces for water adsorption based on a comparison of their surface energies. An analysis of the mechanism of water adsorption on the surface of t-ZrO₂ (101) and t-YSZ (101) showed that H₂O on unstabilized t-ZrO₂ (101) is adsorbed dissociatively with an energy of -1.22 eV, as well as by the method of molecular chemisorption with an energy of -0.69 eV and the formation of a hydrogen bond with a bond length of 1.01 Å. In the case of t-YSZ (101), water is molecularly adsorbed onto the surface with an energy of -1.84 eV. Dissociative adsorption of water occurs at an energy of -1.23 eV, near the yttrium atom. The calculations showed that ab initio research methods are capable of describing the mechanism of phase transitions of materials under the influence of alloying. That is, by optimizing the parameters of DFT calculations, it is possible to observe the effects of doping on other physical and chemical properties of materials, which are still beyond the scope of quantum chemical modeling. The obtained results complement the database of research works carried out in the field of the application of biocompatible zirconium dioxide crystals and ceramics in green energy generation and can be used in designing humidity-to-electricity converters and creating solid oxide fuel cells based on ZrO₂.

Recent studies have been able to detect α-synuclein (αSyn) seeding in formaldehyde-fixed paraffin-embedded (FFPE) tissues from patients with synucleinopathies using seed amplification assays (SAAs), but with relatively low sensitivity due to limited protein extraction efficiency. With the aim of introducing an alternative option to frozen tissues, we developed a streamlined protein extraction protocol for evaluating disease-specific seeding in FFPE human brain. We evaluated the protein extraction efficiency of different tissue preparations, deparaffinizations, and protein extraction buffers using formaldehyde-fixed and FFPE tissue of a single Lewy body disease (LBD) subject. Alternatively, we incorporated heat-induced antigen-retrieval and dissociation using a commercially available kit. Our novel protein extraction protocol has been optimized to work with 10 sections of 4.5-µm-thickness or 2-mm-diameter micro-punch of FFPE tissue that can be used to seed SAAs. We demonstrated that extracted proteins from FFPE still preserve seeding potential and further show disease-specific seeding in LBD and multiple system atrophy. To the best of our knowledge, our study is the first to recapitulate disease-specific αSyn seeding behavior in FFPE human brain, with structural validation. Our findings open new perspectives in re-evaluating archived human brain tissue, extending the disease-specific seeding assays to larger cohorts to facilitate molecular subtyping of synucleinopathies.

The intrinsic dynamic and static nature of the non-covalent Br-*-Br interactions in the neutral polybromine clusters is elucidated for Br4–Br12, applying QTAIM dual functional analysis (QTAIM-DFA). The asterisk (*) emphasizes the existence of the bond critical point (BCP) on the interaction in question. Data from the fully optimized structures correspond to the static nature of interactions. The intrinsic dynamic nature is originated from those of the perturbed structures generated using the coordinates derived from the compliance constants for the interactions and the fully optimized structures. The non-covalent Br-*-Br interactions in the L-shaped clusters of the Cs symmetry are predicted to have the typical hydrogen bond nature without covalency, although the first ones in the sequences have the vdW nature. The L-shaped clusters are stabilized by the n(Br)->σ*(Br–Br) interactions. The compliance constants for the corresponding non-covalent interactions are strongly correlated to the E(2) values based on NBO. Indeed, the MO energies seem not contribute to stabilize Br4 (C2h) and Br4 (D2d), but the core potentials stabilize them, relative to the case of 2Br2, maybe due to the reduced nuclear-electron distances in the average for the dimmers.

The production and quality of Phaseolus vulgaris (snap bean) have been negatively impacted by leaf crumple disease caused by two whitefly-transmitted begomoviruses; cucurbit leaf crumple virus (CuLCrV) and sida golden mosaic Florida virus (SiGMFV), which often appear as a mixed infection in Georgia. Host resistance is the most economical management strategy against whitefly-transmitted viruses. Currently, information is not available with respect to resistance to these two viruses in commercial cultivars. In two field seasons (2018 and 2019), we screened Phaseolus sp. genotypes (n = 84 in 2018; n = 80 in 2019; most of the genotypes were common in both years with a few exceptions) for resistance against CuLCrV and/or SiGMFV. Twenty genotypes with high- to moderate-levels of resistance (disease severity ranging from 5-50%) to CuLCrV and/or SiGMFV were identified. Twenty-one genotypes were found to be highly susceptible with a disease severity of ≥66%. Adult whitefly counts differed significantly among snap bean genotypes for both years. The whole genome of these Phaseolus sp. (n=82) genotypes was sequenced and genetic variability among them was identified. Over 900 giga-base (Gb) of filtered data were generated and >88% of the resulting data were mapped to the reference genome, and SNP and Indel variants in Phaseolus genotypes were obtained. A total of 645,729 SNPs and 68,713 Indels including 30,169 insertions and 38,543 deletions were identified, which were distributed in 11 chromosomes with chromosome 02 harboring the maximum number of variants. These phenotypic and genotypic information will be helpful in genome-wide association studies that will aid in identifying genetic basis of resistance to these begomoviruses in Phaseolus sp.

Mosquitoes are a family of the order Diptera, which includes more than 3500 species. Two groups able to suck human blood and transmit diseases: the anophelines and the culicines comprise several genera such as Culex, Aedes and Aedes communis (Ac). Previous study has demonstrated a significant relationship between Ac sensitization and either extract or single bee venom components suggesting a “bee-mosquito syndrome” occurrence. It is well known that CCD can interference with the measurement of quantitative IgE results. Hence, it has been hypnotized that the presence of sIgE to CCD could have a role in the Bee-Mosquito syndrome. Method Serum from 21 different Mosquito and Ape melifera allergic individuals were combined with extracts of Mosquito (in house) and Apis melifera. SDS-PAGE and Immunoblot (IB) were carried out without and with with CCD-Inhibitor. Results The data would suggest IgE binding to common bands between Culex male, Culex female and Aedes species mosquitos of approximate molecular weight ~21kDa, ~35kDa, ~40kDa and ~55kDa. Whilst IgE binding has been observed to protein bands from the Apis melifera extract, these bands do not align with any present in the mosquito extracts. The use of a CCD-Inhibitor results in differences in IgE binding. Specifically, bands that were previously observed in the Apis melifera venom sample without use of CCD-Inhibitor at 40kDa and 90kDa are no longer observed when CCD-Inhibitor is used. Two bands of the Apis melifera venom remain present between 15-20kDa. No major differences in banding pattern were observed for the mosquito samples with or without CCD-Inhibitor, although the blot appears cleaner with less background when CCD-Inhibitor is used. Conclusion Further experiments have to be done to determine whether the reactive bands from Apis melifera are unrelated proteins or whether the proteins are related homologues of varying molecular weight.

Red color conversion materials have often been used in conventional white LEDs (light-emitting diodes) to enhance the insufficient deep red component and thus improve the color rendering property. Quantum dots (QDs) are one of the candidates due to their flexibility in controlling the emission wavelength, which is attributed to the quantum confinement effect. Two types of remote QD components, i.e., QD films and QD caps, were prepared and applied to conventional white LED illumination to improve the color rendering properties. Thanks to the red component near 630 nm caused by the QD components, the color rendering indices(CRIs) of both Ra and R9 could be increased to over 95. It was found that both the diffusing nature of the reflector and the light recycling process in the vertical cavity between the bottom reflector and the top optical films play important roles in improving the color conversion efficiency of remote QD components. The present study showed that the proper application of remote QDs combined with a suitable optical cavity can control the correlated color temperature of the illumination over a wide range, thus realizing different color appearances of white LED illumination. In addition, a high CRI of over 95 could be achieved due to sufficient excitation from fewer QDs due to the strong optical cavity effect.