Coronary artery disease is the most prevalent cardiovascular disease, claiming millions of lives annually around the world. The current treatment includes surgically inserting a tubular construct called as a stent inside arteries to restore blood flow. However, due to lack of patient-specific design, the commercial products cannot be used with different vessel anatomies. In this review, we have summarized the drawbacks in existing commercial metal stents which face problems of restenosis and inflammatory responses, owing to the development of neointimal hyperplasia. Further, we have highlighted the fabrication of stents using biodegradable polymers, which can circumvent most of the existing limitations. In this regard, we elaborated on utilization of new fabrication methodologies based on additive manufacturing such as three-dimensional printing to design patient-specific stents. Finally, we have discussed on the functionalization of these stent surfaces with suitable bioactive molecules which can prove to enhance their properties in preventing thrombosis and better healing of injured blood vessel lining.

Tissue engineering is an emerging field of research due to its growing impact on the regeneration of tissue injured from damage and organ failure. Small hydrogel microspheres containing regenerative cells and stimulators can be used as building blocks to regenerate tissue by injecting them into damaged areas; a microneedle is used to minimize the incision and any associated infections. To address the need for production of a large number of microspheres for use in tissue engineering, we developed a 3D coaxial multi-nozzle flow-focusing device fabricated via a simple 3D-printing method that demonstrates a high rate of microsphere production per nozzle. This device has six coaxial microscale nozzles that produce hydrogel microspheres. Two individual parts—the inlet and nozzle—can be made separately by a 3D printer and bonded together using uncured photo-curable resin as glue. The dimensions of the microspheres are between 100 μm and 1200 μm. They are produced by adjusting the flow rate ratio between the dispersed and continuous media. A flow rate ratio of 180 demonstrated the highest microsphere production rate of 2.12e+5 microspheres per sec (0.25 mL/min). This microsphere production rate per nozzle is four times higher than that of currently available devices.

The purpose of this in vitro study is to evaluate the effectiveness of incorporating a new irrigation system into a surgical guide and monitor its effect on heat generation during implant bed preparation. A total of 48 surgically guided osteotomies were performed on 12 bovine ribs divided into 4 groups, using different irrigation techniques: Group A (test) had entry and exit channels incorporated into the guide; Group B had a similar design with an entry channel only; Group C had conventional external irrigation; Group D (control) had no irrigation. Heat generation during the osteotomies was measured using thermocouples placed at a depth of 2 mm and 6 mm. The lowest mean temperature was observed in Group A (22.1°C at 2mm and 21.4°C at 6mm), this was statistically significant when compared with Groups C and D (p<0.001). Group A showed a lower mean temperature compared with Group B as well, however statistically significant only at 6mm depth (p<0.05). In conclusion, the proposed guide has significantly reduced heat generation during implant osteotomy. The integration of an exit cooling channel can resolve limitations found in previously designed surgical guides and can be easily incorporated into computer designing and 3D printing software.

In the bioprinting process, controlling the motion of bioprinters involves a computer-aided design (CAD) model, converting that model into g-code, and transmitting the motion commands to the bioprinters. The g-code file contains information about the motion of the axes and can be generated using various software. However, a challenge arises when using g-code between different bioprinters. Therefore, the objective of this study was to propose a reliable method for analyzing the differences in 3D bioprinting devices by parameterizing a crucial variable for extrusion bioprinting: the E-value. Four bioprinters from three different manufacturers were used to investigate the extrusion behavior when subjected to the same E-value.

Three-dimensional (3D) printing technology, also known as additive manufacturing (AM), has emerged as an attractive state-of-the-art tool for precisely fabricating functional materials with complex geometries, championing several advancements in tissue engineering, regenerative medicine, and therapeutics. However, this technology has an untapped potential for biotechnological applications, such as sensor and biosensor development. By exploring these avenues, the scope of 3D printing technology can be expanded and pave the way for groundbreaking innovations in the biotechnology field. Indeed, new printing materials and printers would offer new possibilities for seamlessly incorporating biological functionalities within the growing 3D scaffolds. Herein, we review the extrusion-based 3D printing modalities emphasizing biosensor applications. We highlighted the application of natural, synthetic, and composite biomaterials as 3D-printed soft hydrogels. Emphasis was placed on the approach by which the sensing molecules were introduced during the fabrication process. Finally, the future perspective was provided.

Synthesis of heterodinuclear 3d transition metal complexes in which two metal ions are introduced in equivalent coordination sites of a ligand is quite uncommon. We have previously shown that the application of the cis-trans isomerization of the oxamido group was able to furnish such a possibility. In the present paper we demonstrate that this synthetic pathway, relying on the possibility of changing the conformation (cis vs trans) of the oxamido group, can be extended to other ligands. Although we have not been able to structurally characterize these complexes, EPR and magnetic data do confirm the efficiency of this reaction pathway. We also demonstrate that the cis-trans isomerization of the oxamido group is not due to a particular property of the ion involved in the reaction. In fact, isomerization is governed by the basicity of the reaction medium. According to the reaction condition, it is possible to favor or not this phenomenon, and to increase the accessibility to a larger number of novel genuine complexes. But the oxophilic character of the lanthanide ions impedes this isomerization in 3d-4f complexes. The very weak magnetic interactions observed in these Cu-Gd complexes can be explained thanks to spin polarization.

Based on three-dimensional optical proximity correction (3D OPC), recent advancements in 3D lithography have enabled the high-fidelity customization of 3D micro-optical elements. However, micron-to-millimeter scale structures represented by Fresnel lens design bring more stringent requirements for 3D OPC, which poses significant challenges to the accuracy of models and the efficiency of algorithms. Thus, a lithographic model based on optical imaging and photo-chemical reaction curve is developed in this paper, and a sub-domain division method with a statistics principle is proposed to improve the efficiency and accuracy of 3D OPC. Both the simulation and the experimental results showed the superiority of the proposed 3D OPC method in the fabrication of the Fresnel lenses. The computation memory requirements of the 3D OPC are reduced to below 1 %, and the profile error of the fabricated Fresnel lens reduced 79.98%. Applying the Fresnel lenses to an imaging system, the average peak signal to noise ratio (PSNR) of the image increased by 18.92 %, and the average contrast of the image enhanced by 36 %. We believe the proposed 3D OPC method can be extended to the fabrication of vision-correcting ophthalmological lenses.

While Neural Radiance Fields (NeRF) are gaining increasing interest in various domains as innovative methods for novel view synthesis and image-based reconstruction, their potential application in the realm of Cultural Heritage remains unexplored. Purpose of this paper is to assess the effectiveness of applying NeRF to sets of images of digital heritage objects and sites. The study’s findings demonstrate that NeRF could be valuable when used in combination with or as a comparison to other well-established techniques such as photogrammetry, to expand the possibilities of preserving and presenting heritage assets with enhanced visual fidelity and accuracy. Particularly, NeRF show promising results in improving the rendering of translucent and reflective surfaces, objects with homogeneous textures, and elements with intricate details. In addition, we demonstrate that, when considering the same set of input images (with known camera poses), reducing the image quality or the number of images results in significantly less information loss with NeRF compared to photogrammetry. This suggests that NeRF is preferentially suited for scenarios involving sparse information or low-quality photos or videos, which could be especially valuable in risky or challenging situations.

3D printing is playing an important role in cardiovascular disease by use of personalised models with replication of normal anatomy and pathology with high accuracy and reliability. While 3D printed heart and vascular models are shown to improve medical education, preoperative planning and simulation of cardiac procedures, and enhance communication with patients, 3D bioprinting however, represents a potential advancement of 3D printing technology by printing cellular or biological components, functional tissues and organs that can be used in a variety of applications in cardiovascular disease. Recent advances in bioprinting technology have shown the ability to support vascularisation of large scale constructs with enhanced biocompatibility and structural stability, thus creating opportunities to replace damaged tissues or organs. In this review, we provide an overview of the use of 3D bioprinting in cardiovascular disease with a focus on technologies and applications in cardiac tissues, vascular constructs and grafts, heart valves and myocardium. Limitations and future research directions are highlighted.

Tumor cells evolve in a complex and heterogeneous environment composed of different cell types and an extracellular matrix. Current 2D culture methods are very limited in their ability to mimic the cancer cell environment. In recent years, various 3D models of cancer cells have been developed, notably in the form of spheroids/organoids, using scaffold or cancer-on-chip devices. However, these models have the disadvantage of not being able to precisely control the organization of multiple cell types in complex architecture and are sometimes not very reproducible in their production, and this is especially true for spheroids. Three-dimensional bioprinting can produce complex, multi-cellular, and reproducible constructs in which the matrix composition and rigidity can be adapted locally or globally to the tumor model studied. For these reasons, 3D bioprinting seems to be the technique of choice to mimic the tumor microenvironment in vivo as closely as possible. In this review, we discuss different 3D-bioprinting technologies, including bioinks and crosslinkers that can be used for in vitro cancer models, and the techniques used to study cells grown in hydrogels; finally, we provide some applications of bioprinted cancer models.

Background: The main objective of this study is to develop a customized metatarsophalangeal implant for the treatment of various conditions affecting this specific joint. This approach involves replacing the joint with a custom implant designed specifically to fit each patient's unique anatomical structure. The need for custom implants stems from the obvious lack of size variety available, which presents a major challenge when, the search for the ideal size implant can be a hard task, also when considering the possibility of extensive modification of the bone to adapt it to the available implant. This adaptation, often synonymous with bone reduction, can cause significant post-operative pain for the patient and impact healing time. Methods: A comparative study of modeling software was carried out to select the perfect software, by defining and comparing the relevant criteria. Similarly, the different biomaterial options were examined and compared to select the one best suited to this project, mentioning the imaging modality used to determine the types of images used for our approach. Finally, the 3D printers used in this work were represented, highlighting their technical characteristics. Findings: A resin metatarsophalangeal implant prototype was created using 3D modeling and reconstruction software and tools. Interpretation: Reconstruction and 3D modeling techniques are revolutionizing implant creation, offering customized solutions for patients suffering from metatarsophalangeal joint disorders caused by a wide range of diseases. These results have significant implications for disability management and rehabilitation, encouraging further exploration and progress.

Manufacturing of facial epithesis is a complex technological process including several traditional stages of production, accompanied by aggravated psycho-emotional status of the patient. One of the main factors causing discomfort in patients with facial defects is the process of obtaining silicone impressions from the wound surface and the long waiting period for the final epithesis. Active development of digital technologies in medicine and dentistry helps specialists not only to automate most of the traditional stages of manufacturing of dento-mandibular and facial prostheses, but also improves the quality of life of patients by increasing the efficiency of services and reducing the production time of prosthetic structures. The application of digital technologies in the production of facial epithesis was difficult due to the lack of specialized 3D-software for modeling and material for further additive manufacturing of structures. The authors developed a unique technology for 3D modeling and additive manufacturing of facial epithesis, including a 3D CAD module and material for 3D printing. The primary objective was to fabricate immediate facial prostheses in the postoperative period in the shortest possible time until the final epithesis was fabricated.

The present study aimed to characterize the microstructure of a temporary 3D printing resin (Resilab Temp), evaluating the optical properties and mechanical behavior according to different post-processing curing times. For the analysis of the surface microstructure and establishment of the best printing pattern, samples in bar format following ISO 4049 (25 x 10 x 3 mm) were designed in CAD software (Rhinoceros 6.0), printed on the W3D printer (Wilcos), and light-cured in Anycubic Photon at different times (without curing, 16 minutes, 32 minutes, and 1 hour). For the structural characterization, analyses were carried out in FTIR (Fourier Transform Infrared Spectroscopy) and Scanning Electron Microscopy (SEM). The mechanical behavior of the resin was based on flexural strength tests and Knoop microhardness. Color and translucency analysis were performed with a spectrophotometer (VITA Easy Shade Advanced 4.0), which was evaluated following CIELab, using gray, black, and white backgrounds. All analyses were performed immediately after making the samples and repeated after thermal aging with 2 thousand cycles (5-55 °C). The results obtained were statistically analyzed with a significance level of 5%. FT-IR analysis showed about a 46% degree of conversion on the surface and 37% in the center of the resin sample. The flexural strength was higher for the groups polymerized for 32 min and 1h, while the Knoop microhardness did not show a statistical difference between the groups. Color and translucency analysis also did not show statistical differences between groups. According to all the analyses carried out in this study, for the evaluated material, the post-polymerization time of 1 hour can be suggested to improve the mechanical performance of 3D-printed devices.

In recent years, Additive Manufacturing (AM), commonly referred to as 3D printing, has garnered the attention of the scientific community due to its capacity to transform ordinary and traditional items into customized materials at an affordable cost, through various AM processes. Antimicrobial/antibiofilm 3D printed materials are one of the most trending research topics, owing to the growing concerns over the emergence of complex microbial structures called "biofilms" on various surfaces. The review provides an overview of the evolution of additive manufacturing (AM) technologies and their various derivatives, along with a brief description of their materials and applications. It also introduces how biofilms can represent an advantageous lifestyle for microbial populations. The primary objective of this research was to conduct a systematic review on the development of planctonic or biofilm forms of microorganisms on 3D printed materials. The article summarizes commonly studied microorganisms on these materials and presents their 3D printing process, materials, as well as the fields covered by each of the analyzed papers. To the best of our knowledge, this is the first all-inclusive systematic review that amalgamated research conducted in diverse fields to assess the development of biofilms on surfaces produced through three-dimensional printing. Most notably, this review presents a comprehensive account of sustainable approaches for producing antimicrobial materials through 3D printing. Additionally, we assess their advancements in various fields such as medicine, environment, agri-food, and other relevant sectors. The findings of our literature review can be used to recommend appropriate microorganisms, 3D printing materials, and technologies for academic and industrial research purposes focusing on the development of microbial biofilms on 3D printed surfaces. Furthermore, it highlights the potential of environmentally-friendly modified AM technologies to combat biofilms in clinical and non-clinical areas. Our goal with this review is to help readers gain a better understanding of fundamental concepts, inspire new researchers, and provide valuable insights for future empirical studies focused on eradicating biofilms from 3D printed materials.

The increasing request of digitized data among several fields, including the built environment and Cultural Heritage (CH) one points out the need of proficient ways to access, archive and share 3D data and related information among users. The sector of reality capture produces accurate and reliable products that can support building management and CH maintenance, at the price of heavy and resource-demanding data. An emerging solution to this problem is represented by the web platforms for 3D data management, that promise to relieve users from the costs of archive and hardware, providing effective visualization, access and sharing tools. The panorama of commercial web platforms is analyzed according to the Software as a Service business model and the features of some representative platforms are exposed. The paper discusses the main advantages in terms of diffused access and collaboration and the potential issues concerning the long-term archive and data persistence. The future perspectives of the web platform sector are promising as, according to the current development path, could be able to empower the built environment and CH sector with a diffused, systematic and aware use of 3D data.

This research discusses the development of a software-centered EdTech (Education Technology) class model through the implementation of a course titled "3D Time Machine" at a 4-year university in Republic of Korea over two semesters. The course focused on teaching 3D modeling software, Blender, within the history department. The primary objective of offering this course was to equip students from the digital generation with the capability to manipulate digital technology effectively. Through studying historical materials and accumulating domain knowledge, students could construct their narratives from their unique perspectives. This aimed to foster their proficiency in digital technology operation, preparing them for an education environment increasingly centered around virtual worlds. As the use of virtual worlds gains prominence in educational settings, there is a growing need to incorporate curricula that prepare students to thrive as well-prepared citizens in future societies. Assessing the digital competencies of contemporary university students and designing instructional models with particular attention to their needs is becoming increasingly important. This research draws insights from interviews, conducted in both face-to-face and written formats, with students who participated in the "3D Time Machine" course. The interviews revealed valuable insights that can be actively incorporated into the development of software-centered EdTech instructional models. They reported that they expanded their perceptions as they learned how to make their ideas tangible. The course helped students overcome their fear of digital technology. In conclusion, the course effectively employs 3D modeling technology, a software-centered EdTech, as a core element in helping students develop their narratives rapidly and diversely, thereby playing a crucial role in their ability to articulate their unique perspectives.

Pure monocular 3D reconstruction is an ill-posed problem that has attracted the research community's interest due to the affordability and availability of RGB sensors. SLAM, VO, and SFM are disciplines formulated to solve the 3D reconstruction problem and estimate the camera’s ego-motion, so many methods have been proposed. However, most of these methods were not evaluated in large datasets, under various motion patterns, had not been tested under the same metrics, and most of them had not been evaluated following a taxonomy, making their comparison and selection difficult. In this research, we performed a comparison of ten publicly available SLAM and VO methods following a taxonomy, including one method for each category of the primary taxonomy, three machine learning-based methods, and two updates of the best methods, to identify the advantages and limitations of each category of the taxonomy and test if the addition of machine learning or the updates made on those methods improved them significantly. Thus, we evaluated each algorithm under the TUM-Mono benchmark and performed an inferential statistical analysis to identify significative differences through its metrics. Results determined that sparse-direct methods significantly outperformed the rest of the taxonomy, and fusing them with machine learning techniques significantly improves the performance of geometric-based methods from different perspectives.

Most common classifications for acetabular bone defects are based on radiographic two-dimension imaging, with low reliability and reproducibility. With the rise of modern processing techniques based on 3D modelling, methodologies for volumetric quantification of acetabular bone loss are available. Our study aims to describe a new methodology for quantitative assess-ment of acetabular defects, based on 3D modelling, focused on the surface analysis of the integrity of the main anatomical structures of the acetabulum represented by four corresponding sectors (posterior, superior, anterior, and medial). The defect entity is measured as the Area Increase Ra-tio (AIR) detected in all the sectors analyzed on three planes of view (frontal, sagittal and axial) compared to healthy hemipelvises. The analysis was performed on 3D-models from the CT-scan of six exemplary specimens with a unilateral pathological hemipelvis. AIR between the native and the pathological hemipelvis was calculated for each sector, for a total of 48 analysis (range, +0.93% - +171.35%). AIR of >50% were found in 22/48(45.8%) sectors and affected mostly the posterior, medial and superior sectors (20/22, 90.9%). Qualitative analysis showed consistency of the data with the morphological features of the defects. Further studies with larger samples are needed to validate the methodology and potentially develop a new classification scheme.

In the last 20 years, TADs have become one of the topics in orthodontic science, as it becomes one of the effective anchorages in moving teeth in a 3D movement to treat malocclusion and dental-alveolar orthopedic. Problems with the collusion of the roots of the teeth and trauma have hindered the use of these TADs; one of the solutions to keep TADs safe is a step-by-step innovation of procedure to make this anchorage concept using TAD safe. Making surgical guides for single-standing TADs is essential, and in practice, it is virtually possible with the advance of today's CAD/CAM and 3D printers. The content subject in the paper contains two parts: the consideration of why a surgical guide is necessary for the implantation of TADs and the making of the Surgical guide itself.

In this study, we designed a functional neuro-cardiac model to help us examine the role of neuronal regulation and confirm the importance of neural innervation techniques for cardiac tissue regeneration. A three-dimensional (3D) bioprinted neuro-cardiac scaffold composed of a mixture of gelatin-alginate and alginate-genipin-fibrin hydrogels was developed with a 2:1 ratio of AC16 cardiomyocytes (CMs) and retinoic acid differentiated SH-SY5Y neuronal cells (NCs) respectively. A unique semi-3D bioprinting approach was adopted where the CMs were mixed in the cardiac bioink and printed using an anisotropic accordion design to mimic the physiological tissue architecture in vivo. The voids in this 3D structure were methodically filled in using a NCs-gel mixture and cross-linked. Confocal fluorescent imaging using Microtubule-associated protein 2 (MAP-2) antibodies for labeling NCs, and the MyoD1 antibody for CMs revealed functional coupling between the two cell types in the final cross-linked structure. This data confirmed the development of a physiologically functional neuro-cardiac model that can be used to study neuro-cardiac modulation under physiological and pathological conditions.

In recent years, with the development of social media, people are more and more inclined to upload text, pictures and videos on the platform to express their personal emotions, thus the number of short videos is increasing and becoming the first choice for people to socialize. Unlike the traditional way, people can convey their personal emotions and opinions through media other than words, such as video images, etc. for external information. Therefore, the expression and analysis of emotions is not only through text, but also through the analysis of emotional needs in images and videos, and the research scholars have customized products for individual users. Compared with pure text content, video information can more intuitively express users' happiness, anger and sorrow, thus short video-related applications have gained more and more popularity among Internet users in recent years. However, not all short videos on social networking sites can accurately express users' emotions, and related text information can more accurately assist sentiment analysis and thus improve accuracy. However, short video sentiment analysis based on video frame images is inaccurate in some scenarios, such as when expressing tears of joy, the sentiment expressed by the user's facial expression and voice are different, which will cause errors in the analysis of sentiment. As a result, researchers began to consider multimodal sentiment analysis to reduce the impact of the above scenarios on short video sentiment analysis. This paper focuses on proposing a sentiment analysis method for short videos. We first propose a residual attention model to make full use of the information in audio to classify the emotions contained in them. Then the text information in the dataset is classified by feature extraction. The key to extract features from text information is not only to retain the semantic information of the text, but also to explore the potential emotional information in the text, so as to ensure the integrity of the text information features. The experiments show that the sentiment analysis model proposed in this paper is more superior than the baselines.

An approach employing ultrafast laser hybrid subtractive-additive microfabrication combining ablation, 3D nanolithography and welding is proposed for the realization of Lab-On-Chip (LOC) device. Single amplified Yb:KGW fs-pulsed laser source is shown to be suitable for fabricating microgrooves in glass slabs, polymerization of fine-meshes filter out of hybrid organic-inorganic photopolymer SZ2080 inside them, and, lastly, sealing the whole chip with cover glass into a single monolithic piece. The created microfluidic device proved its particle sorting function by separating 1 μm and 10 μm polystyrene spheres in a mixture. All together, this shows that fs-laser microfabrication technology is a flexible and versatile tool for the manufacturing of mesoscale multi-material LOC devices.

Digital twins are gaining in popularity for simulating complex natural and urban environments. In this context, accurate segmentation of objects within 3D urban environments is of crucial importance. The aim of this project is to develop a methodology for extracting buildings from textured 3D meshes. To this end, PicassoNet-II, a semantic segmentation architecture is employed. The methodology also incorporates Markov field-based contextual analysis to assess post-segmentation features. In addition, building instantiation is performed using cluster analysis algorithms. Training this model to fit various datasets requires a large amount of annotated data, both from Quebec City, Canada, and from simulated data. Experimental results show that the use of simulated data improves segmentation accuracy, and the DBScan algorithm proves effective in extracting isolated buildings. This project paves the way for improved applications in 3D urban modeling, offering opportunities in fields ranging from urban planning to resource management. The positive results with simulated data reinforce the impact of this research on improving digital models of our ever-changing urban environments.

3D Zernike moments based on 3D Zernike polynomials have been successfully applied to the field of voxelized 3D shape retrieval and have attracted more attention in biomedical image processing. As the order of 3D Zernike moments increases, both computational efficiency and numerical accuracy decrease. Due to this phenomenon, a more efficient and stable method for computing high-order 3D Zernike moments was proposed in this study. The proposed recursive formula for computing 3D Zernike radial polynomials combines the recursive calculation of spherical harmonics to develop a voxel-based algorithm for the calculation of 3D Zernike moments. The algorithm was applied to the 3D shape Michelangelo's David with a size of 150×150×150 voxels. As compared to the method without additional acceleration, the proposed method uses a group action of order sixteen orthogonal group and saving unnecessary iterations, the factor of speed-up is 56.783±3.999 when the order of Zernike moments is between 10 and 450. The proposed method also obtained an accurate reconstructed shape with the error rate (normalized mean square error) of 0.00 (4.17×10^-3) when the reconstruction was computed for all moments up to order 450.

The field of 3D model generation has become essential across various industries, including gaming, virtual and augmented reality (VR/AR), architecture, and medical imaging. Traditionally reliant on manual efforts, 3D content creation is now being transformed by deep generative models, enabling more efficient, scalable, and dynamic generation of complex shapes and environments. This survey provides a comprehensive review of key backbone architectures used for 3D generation, including autoencoders, variational autoencoders (VAEs), generative adversarial networks (GANs), autoregressive models, diffusion models, normalizing flows, attention-based models, CLIP-guided models, and procedural generation techniques. We explore each model’s role in 3D generation, highlighting their strengths—such as the precision of VAEs, the realism of GANs, the stability of diffusion models, and the scalability of procedural methods—alongside their limitations, such as training instability, high computational costs, and the difficulty in handling multi-modal data. Additionally, we discuss the increasing relevance of attention-enhanced models and the integration of text-based CLIP supervision for improved semantic alignment in 3D outputs. The survey concludes with an analysis of open challenges, including balancing efficiency with expressiveness, managing training complexity, and addressing dataset limitations. It also identifies future research directions, such as few-shot learning, hybrid architectures, and neural-symbolic approaches, which promise to advance the field by improving the generalization and versatility of 3D generation models. This paper aims to guide researchers and practitioners in navigating the evolving landscape of 3D generative methods and inspire new innovations in the creation of realistic, high-quality 3D content.

This paper aims to present the method of producing visual media for communicating the Asinara Island National Park plan. These products are landscape visualizations able to foster landscape preservation both from the point of view of the management of the landscape and of the citizen's involvement in the communication of the historical and environmental values of the landscape. Starting from landscape information gathering, the research has experimented with an operative method for processing different graphic representations from the same geographic database, calibrating the outputs to different audiences, their needs, objectives, and literacy skills. Three different types of products are presented: the first is a digital, dynamic and multisectoral decision-making GIS tool for park management. The second is a 3D model, aimed to the virtual fruition. The third is a map of the zoning park plan drawn to be easily readable to the non-expert public. This case study emerges as a replicable method to process the landscape information to make different visualization tools from a single geographic model, to meet the different requirements that arise from a complex landscape planning process.

New in vitro approaches for the assessment of their toxicity are crucial for creating better risk assessments given the growing use of nanoparticles (NPs) in the production of consumer goods. Humans will be exposed to nanoparticles through the inhalation route from contaminated aerosol. A promising method for evaluating the genotoxicity of NPs in vitro uses human airway epithelial cells. This study aimed to determine whether there were differences in morphology change of human bronchial/tracheal epithelial (HBTEC) cells responded to NPs in 2D and 3D spheroid models and to evaluate genotoxicity in 2D and 3D cultures after 24 hr exposure to TiO2-, Ag- and ZnO-NPs using the comet assay. Our 2D and 3D HBTEC cultures with TiO2-NPs did not show any statistically significant genotoxicity compared to controls for concentration points tested in vitro. HBTEC cells grown as 2D indicated that exposure to ZnO-NPs at low concentrations (10-50 ug/mL) for 24 hr did not cause any genotoxic effect but, at high concentrations, genotoxicity was observed. In contrast, treatment of 2D HBTEC with AgO-NPs led to an elevated in percentage of tail DNA damage from 50 ug/mL to 100 ug/mL, which was concentra-tion-dependent. Using 3D spheroid assays revealed a lower %tail length in ZnO- and AgO-NPs, thus exhibiting in vitro genotoxicity of NPs in this cell model. Spheroids (3D) rather than mono-layer cultures (2D) are believed to more precisely represent in vivo-like cell behavior when evaluating genotoxicity. Together, our findings demonstrate the genotoxic effects of NPs and point to the critical role that cell culture models play in the evaluation of toxicological risk.

In the production of green parts from powder, there is unavoidable slight deviation in the die filling, even when high-quality powders are used. The quantity of powder in the die varies and thus affects the weight of the compact. This filling variation results in variation of the pressing force, and thus influences the part geometry. The development of the DORST Netshape® System was conceived as an autonomous manufacturing system in order to compensate for these effects. Based on the Dorst Industry 4.0 innovations for part weight measuring immediately after pressing in combination with a laser dimension measuring system, this technology package attempts to reach enhanced precision and consistency in production. The paper presents results from various trials that show the capability of this new system, designed to improve the quality of pressed parts.

This paper presents the results of the investigation of composite sinters W-TiB2 which were used as an electrode in the process of electro-spark deposition (ESD) and the examination of the deposited layers. The scope of the study includes detailed characteristics of powder mixtures, composite sinters made using the spark plasma sintering method (SPS) and layers deposited in the electro-spark process. The ESD process, using the W+30 vol.% TiB2 electrode, was carried out using an automated device. The substrates were made of copper and aluminium. The topography analysis of the surfaces of the composite layer and the evaluation of their wear resistance properties are also presented. The analysis of the results of research showed the possibility to obtain, using the SPS method, composite materials of good quality, which can be used as electrodes in the ESD process. The obtained layers had increased wear resistance in relation to the substrate material.

We present progress in fast, high-resolution imaging, material classification, and fault detection using hyperspectral X-ray measurements. Classical X-ray CT approaches rely on data from many projection angles, resulting in long acquisition and reconstruction times. Additionally, conventional CT cannot distinguish between materials with similar densities. However, in additive manufacturing, the majority of materials used are known a priori. This knowledge allows to vastly reduce the data collected and increase the accuracy of fault detection. In this context, we propose an imaging method for non-destructive testing of materials based on the combination of spectral X-ray CT and discrete tomography. We explore the use of spectral X-ray attenuation models and measurements to recover the characteristic functions of materials in heterogeneous media with piece-wise uniform composition. We show by means of numerical simulation that using spectral measurements from a small number of angles, our approach can alleviate the typical deterioration of spatial resolution and the appearance of streaking artifacts.

Fatigue remains a challenge especially for high end metal AM parts and materials. From a design perspective, the fatigue limit of an AM solution can be improved upon by optimizing the manufacturing process for a certain material and part. In addition, improved accuracy of design methodologies aids in capturing the features critical for fatigue and quantifies their significance to desired part lifetime as well as providing a basis for their avoidance. In current work we present an overall concept merging thermomechanical process and powder bed solidification modeling to micromechanical analysis of fatigue of the resulting material microstructure. Material features critical to fatigue, particularly surface roughness, internal defects such as porosity and cracks and on the other hand inclusions, can be assessed directly on the basis of AM part microstructure with respect to the resulting fatigue limit. Case analyses consist of maraging steel and nickel alloys. The overall scheme provides a basis for optimization of metal AM solutions against fatigue and multiscale modeling founded basis for fatigue design.

Quality assurance has been one of the major challenges in laser-based additive manufacturing (AM) processes. This study proposes a novel process modeling methodology for layer-wise in-situ quality monitoring based on image series analysis. An image-based autoregressive (AR) model has been proposed based on the image registration function between consecutively observed thermal images. Image registration is used to extract melt pool location and orientation change between consecutive images, which contains sensing stability information. Subsequently, a Gaussian process model is used to characterize the spatial correlation within the error matrix. Finally, the extracted features from the aforementioned processes are jointly used for layer-wise quality monitoring. A case study of a thin wall fabrication by a Directed Laser Deposition (DLD) process is used to demonstrate the effectiveness of the proposed methodology.

Additive Manufacturing (AM) simplifies the fabrication of complex geometries. Its scope has rapidly expanded from the fabrication of pre-production visualization models to the manufacturing of end use parts driving the need for better part quality assurance in the additively manufactured parts. Machine learning (ML) is one of the promising techniques that can be used to achieve this goal. Current research in this field includes the use of supervised and unsupervised ML algorithms for quality control and prediction of mechanical properties of AM parts. This paper explores the applications of supervised learning algorithms - Support Vector Machines and Random Forests. Support vector machines provide high accuracy in classifying the data and is used to decide whether the final parts have the desired properties. Random Forests consist of an ensemble of decision trees capable of both classification and regression. This paper reviews the implementation of both algorithms and analyzes the research carried out on their applications in AM.

OBJECTIVE: Although 3D-printed anatomic models are not new to medicine, the high costs and lengthy production times entailed have limited their application. Our goal was developing a new and less costly 3D modeling method to depict organ-tumor relations at faster printing speeds. METHODS: We have devised a method of 3D modeling using DICOM images. Coordinates are extracted at a specified interval, connecting them to create mesh-work replicas. Adjacent constructs are depicted by density variations, showing anatomic targets (ie, tumors) in contrasting color. RESULTS: An array of organ solid-tumor models were printed via Fused Deposition Modeling 3D printer at significantly less cost ($0.05/cm3) and time expenditure (1.73 min/cm3; both, p<.001). Printed models helped promote visual appreciation of organ-tumor anatomy and adjacent tissues. Our mesh-work 3D thyroidal prototype reproduced glangular size/contour and tumor location, readily approximating the surgical specimen. CONCLUSIONS: This newly devised mesh-type 3D printing method may facilitate anatomic modeling for personalized care and improve patient awareness during informed surgical consent.

3D printing facilitates the straightforward construction of microchannels with complex three-dimensional architectures. Here, we demonstrate 3D-printed modular mixing components that operate on the basis of splitting and recombining fluid streams to decrease interstream diffusion length. These are compared to helical mixers that operate on the principle of chaotic advection.

It is time-consuming for acquiring complete data by fully phase encoding in two orthogonal directions along with one frequency encoding direction. Undersampling in the 3D k-space is promising in accelerating such 3D MRI process. Though 3D undersampling can be conducted according to predefined probability density, the density based method is not optimal. Because of the large amount of 3D data and computational cost, it is challenging to perform data-driven and learning-based 3D undersampling and subsequent 3D reconstruction. To tackle this challenge, this paper proposes a deep neural network called EEUR-Net, realized by optimizing specific undersampling patterns for the fully-sampled 3D k-space data. Innovatively, our undersampling algorithm employs an end-to-end deep learning approach to optimize phase encoding patterns and uses a 3D U-Net for image reconstruction of undersampled data. Through end-to-end training, we obtain an optimized 3D undersampling pattern, which significantly enhances the quality of the reconstructed image under the same acceleration factor. A series of experiments on a knee MRI dataset demonstrated that, in comparison to standard random uniform, radial, Poisson and equispaced Cartesian undersampling schemes, our end-to-end learned undersampling pattern considerably improves the reconstruction quality of undersampled MRI images.

Three-dimensional reconstruction plays an important role in assisting doctors and surgeons in diagnosing bone defects’ healing progress. Common three-dimensional reconstruction methods include surface and volume rendering. As the focus is on the shape of the bone, volume rendering is omitted. Many improvements have been made on surface rendering methods like Marching Cubes and Marching Tetrahedra, but not many on working towards real-time or near real-time surface rendering for large medical images, and studying the effects of different parameter settings for the improvements. Hence, in this study, an attempt towards near real-time surface rendering for large medical images is made. Different parameter values are experimented on to study their effect on reconstruction accuracy, reconstruction and rendering time, and the number of vertices and faces. The proposed improvement involving three-dimensional data smoothing with convolution kernel Gaussian size 0.5 and mesh simplification reduction factor of 0.1, is the best parameter value combination for achieving a good balance between high reconstruction accuracy, low total execution time, and a low number of vertices and faces. It has successfully increased the reconstruction accuracy by 0.0235%, decreased the total execution time by 69.81%, and decreased the number of vertices and faces by 86.57% and 86.61% respectively.

Solar3D is an open-source software application designed to interactively calculate solar irradiation at three-dimensional (3D) surfaces in a virtual environment constructed with combinations of 3D city models, digital elevation models (DEMs), digital surface models (DSMs) and feature layers. The GRASS GIS r.sun solar radiation model computes solar irradiation based on two-dimensional (2D) raster maps for given day, latitude, surface and atmospheric conditions. With the increasing availability of 3D city models and demand for solar energy, there is an urgent need for better tools to computes solar radiation directly with 3D city models. Solar3D extends GRASS GIS r.sun from 2D to 3D by feeding the model with input, including surface slope, aspect and time-resolved shading, that is derived directly from the 3D scene using computer graphics techniques. To summarize, Solar3D offers several new features which, as a whole, distinguish itself from existing 3D solar irradiation tools: (1) the ability to consume massive heterogeneous 3D city models, including massive 3D city models such as oblique airborne photogrammetry-based 3D city models (OAP3Ds or integrated meshes); (2) the ability to perform near real-time pointwise calculation for duration from daily to annual; (3) the ability to integrate and interactively explore large-scale heterogeneous geospatial data. (4) the ability to calculate solar irradiation at arbitrary surface positions including at rooftops, facades and the ground. Solar3D is publicly available at https://github.com/jian9695/Solar3D.

3D printing is described as the third industrial revolution: its impact is global in industry and progresses every day in society. It presents a huge potential for ecology and evolution, sciences with a long tradition of inventing and creating objects for research, education and outreach. Its general principle as an additive manufacturing technique is relatively easy to understand: objects are created by adding material layers on top of each other. Although this may seem very straightforward on paper, it is much harder in the real world. Specific knowledge is indeed needed to successfully turn an idea into a real object, because of technical choices and limitations at each step of the implementation. This article aims at helping scientists to jump in the 3D printing revolution, by offering a hands-on guide to current 3D printing technology. We first give a brief overview of uses of 3D printing in ecology and evolution, then review the whole process of object creation, split into three steps: (1) obtaining the digital 3D model of the object of interest, (2) choosing the 3D printing technology and material best adapted to the requirements of its intended use, (3) pre- and post-processing the 3D object. We compare the main technologies available and their pros and cons according to the features and the use of the object to be printed. We give specific and key details in appendices, based on examples in ecology and evolution.

We introduce optically clear and resilient free-form micro-optical of pure (non-photosensitized) organic-inorganic SZ2080 material made by femtosecond 3D laser lithography (3DLL). This is advantageous for rapid printing of 3D micro-/nanooptics, including their integration directly onto optical fibers. A systematic study on the fabrication peculiarities and quality of resultant structures is performed. Comparison of microlenses’ resiliency to CW and femtosecond pulsed exposure is determined. Experimental results prove that pure SZ2080 is ∼3 fold more resistant to high irradiance as compared with a standard photo-sensitized material and can sustain up to 1.91 GW/cm² intensity. 3DLL is a promising manufacturing approach for high-intensity micro-optics for emerging fields in astro-photonics and atto-second pulse generation. Additionally, pyrolysis is employed to shrink structures up to 40% by removing organic SZ2080 constituents. This opens a promising route towards downscaling photonic lattices and creation of mechanically robust glass-ceramic structures.

The evaluation of landslide hazard in seismic areas is based on a deterministic analysis to define the stability of the sites. However, deterministic analysis is not able to consider various uncertainties in the analysis process. This paper focuses on the results established by the probabilistic seismic hazard analysis and extends the probabilistic landslide hazard analysis to consider the uncertainties of opposing ground deformations and strength. The work studies the areas between Nibbiano and Sant'Erasmo inhabited centres in the Camerino municipality located in central Italy. The current state of the areas shows dangerous conditions for the building structures. In fact, all constructions present evidence of damage caused by both the 2016 earthquake and slope instability. The studies, carried out through careful geological survey and detailed geophysical investigations, are performed to define the geological, geomorphological and hydrogeological characteristics of the areas and also to run a new analysis aimed to define the material stress-strain behavior. Both inhabited Centers are located on debris deposits with highly variable thicknesses. The key point regards the definition of the depth of unstable mass, its position and its extension. Therefore, this contribution aims to summarize the knowledge of the landslide phenomenon that affected the area, trying to interpret its evolution with new field investigations. Indeed, during the first step, related to the geological and geomorphological detailed surveys, a remarkable geological model was obtained to better interpret the slope dynamics in relation to the structures of this section of the ridge. This model was also confirmed by the geophysical investigations. The study involves a more detailed definition of the landslide perimeter. Indeed, to analyze the phenomenon, it was necessary to study both the local seismic amplification with finite element 2D simulations and the slope stability conditions with finite 3D difference simulation.

Background. Currently, most of the research in breast cancer has been carried out in conventional two-dimensional (2D) cell culture due to its practical benefits, however, the three-dimensional (3D) cell culture is becoming the model of choice in cancer research because it allows cell-cell and cell-extracellular matrix (ECM) interactions, mimicking the native microenvironment of tumors in vivo. Methods. in this work, we evaluated the effect of 3D cell organization on the expression pattern of miRNAs (by Small-RNAseq) and mRNAs (by microarrays) in the breast cancer SKBR3 cell line and analyzed the biological processes and signaling pathways regulated by the differ-entially expressed protein-coding genes (DE-mRNAs) and miRNAs (DE-microRNAs) found in the organoids. Results. We obtained well-defined cell-aggregated organoids with a grape cluster-like morphology with a size up to 9.2×105 μm3. The transcriptomic assays showed that cell growth in organoids significantly affected (all p < 0.01) the gene expression patterns of both, miRNAs and mRNAs, finding 20 upregulated and 19 downregulated DE-microRNAs, as well as 49 upregulated and 123 downregulated DE-mRNAs. In silico analysis showed that a subset of 11 upregulated DE-microRNAs target 70 downregulated DE-mRNAs. These genes are involved in 150 gene on-tology (GO) biological processes such as regulation of cell morphogenesis, regulation of cell shape, regulation of canonical Wnt signaling pathway, morphogenesis of epithelium, regulation of cy-toskeleton organization, as well as in the MAPK and AGE-RAGE signaling KEGG-pathways. In-terestingly, hsa-mir-122-5p (Fold Change (FC)=15.4), hsa-mir-369-3p (FC=11.4), and hsa-mir-10b-5p (FC=20.1) regulated up to the 81 % of the 70 downregulated DE-mRNAs. Conclu-sion, the organotypic 3D cell-organization architecture of breast cancer SKBR3 cells impacts the expression pattern of miRNAs-mRNAs network mainly through overexpression of hsa-mir-122-5p, hsa-mir-369-3p, and hsa-mir-10b-5p. All these findings suggest that the interaction between cell-cell and cell-ECM as well as the change in the culture architecture impacts gene ex-pression, and therefore, support the pertinence of migrating breast cancer research from conven-tional cultures to 3D models.

Path planning in 3D environment is a fundamental research area for robots and autonomous vehicles. Based on the principle ``the shortest path consists of tangents'', RimJump* is proposed as a tangent-based path planning method suitable for finding the shortest path (both off-ground and on-ground) in 3D space (e.g., octomap and point cloud) for mobile platform to follow. RimJump* searches the tangent graph in the form of a path tree and considers the geometrical properties of the locally shortest path. Therefore, the method can provide all of the locally shortest paths that connect the starting point and the target, including the globally shortest path. And the time cost of RimJump* is insensitive to map scale increases in comparison to methods that search the whole passable space rather than the surface of the obstacle, e.g., Dijkstra and A*. In the Results, RimJump* is compared with other methods in terms of path length and time cost.

Background: Melatonin is a potent mitochondrial, cytoprotective and antioxidant molecule with potentially strong anti-aging properties. Topical melatonin has shown to improve the clinical signs of skin aging. Melatosphere™ is a new lipid-based delivery system able to improve stability and skin penetration of melatonin when used in topical formulations. No clinical studies, using objective instrumental data, are available so far regarding the positive effect of Melatosphere™ in improving wrinkles in women with mild-to-moderate skin aging. Study Aim: We evaluate, in an open prospective, evaluator-blinded trial, the effects on skin texture of 2 months treatment with a Melatosphere™ based cream. Subjects and Methods: 15 women aged >45 years with mild to moderate facial skin aging (Glogau score ≥2) participated in the trial, after their informed consent. An ANTERA 3D computer-assisted skin analysis evaluation for the assessment of coarse and fine wrinkles of the periorbital area and melanin content was performed at baseline and after two months of treatment. An evaluator-blinded Investigator Global assessment of skin elastosis, roughness, level of dyscromia, skin dryness and presence of actinic damage was also performed at the same time points using a 4-grade score from 0 (no sign) to 3 (severe sign). Results: At baseline the mean (SD) IGA score was 8.2(1.0). After 2 months the IGA score significantly decrease to 4.2(1.4) (49% reduction) (P=0.0007). ANTERA 3D evaluations showed a significant reduction in skin coarse and fine wrinkles volume in the target area of -31% and -18%, respectively. Melanin content was reduced significantly by -17%. Conclusion: Topical melatonin carried in Melatosphere improves in the short-term signs of skin aging evaluated clinically and by ANTERA 3D device in women with mild to moderate skin aging.

We demonstrated a new approach to the production of three-dimensional-coated patterns using liquid route. Metallic perovskite oxides were coated onto three-dimensional (3D) microstructured substrates with different aspect ratios. The success of the method relies on the solution viscosity monitored by adding viscous liquid. The process of oxide thin films consists in three steps: preparing the precursor solution, coating the solution by spin-coating process onto three-dimensional-Si substrates and post-annealing. The chemical solution 3D-coating is conformal.

Customized wrist splints, particularly for upper extremity orthoses like wrist support braces, are commonly used across numerous clinical scenarios. However, the traditional process for producing personalized wrist splints is largely manual and highly dependent on the expertise of orthopedic specialists. This experience-based approach often leads to suboptimal outcomes, necessitating further refinement of the designs. Recent advancements in Additive Manufacturing (AM) have brought significant innovation to various industries, including orthopedics. This study aims to present a comprehensive methodology that integrates advanced design tools ,like 3D Scanning, with digital manufacturing techniques to produce tailored wrist splints. The produced hand brace aims to offer enhanced mechanical performance and comfort by precisely fitting an individual’s anatomy while minimizing material usage and weight. To achieve optimal design efficiency, the study explores the application of a Topology Optimization (TO) approach for design, while the manufacturing process utilizes Fused Deposition Modeling (FDM), an evolving technology within the Additive Manufacturing (AM) sector.

Prior to clinical trials, preclinical testing of oncology drug candidates is performed by evaluating drug candidates with in vitro and in vivo platforms. For in vivo testing, animal models are used to evaluate the toxicity and efficacy of drug candidates. However, animal models often display poor translational results as many drugs that pass preclinical testing fail when tested in humans, with oncology drugs exhibiting especially poor acceptance rates. The FDA Modernization Act 2.0 promotes alternative preclinical testing techniques, presenting the opportunity to use higher complexity in vitro models as an alternative to in vivo testing, including 3D cell culture models. 3D tissue cultures address many of the shortcomings of 2D cultures by more closely replicating the tumour microenvironment through a combination of realistic drug diffusion, paracrine signaling, cellular phenotype, and vascularization that can better mimic native human tissue. This review will discuss the common forms of 3D cell culture, including cell spheroids, organoids, organs-on-a-chip, and 3D bioprinted tissues. Their advantages and limitations will be presented, aiming to discuss the use of these 3D models to accurately represent human tissue and as an alternative to animal testing. The use of 3D culture platforms for preclinical drug development is expected to accelerate as these platforms continue to improve in complexity, reliability, and translational predictivity.

Transparent and high-hardness materials have become the object of wide interest. Most notably, it concerns technical glasses and crystals. A notable example is a sapphire – one of the most rigid materials having impressive mechanical stability and good optical properties. Nonetheless, using this material for 3D micro-fabrication is not straightforward due to its brittle nature. On the microscale, selective laser etching (SLE) technology is an appropriate approach for such media. Therefore, we present our research on c-cut crystalline sapphire microprocessing by using femtosecond radiation-induced SLE. Here we demonstrate a comparison between different wavelength radiation (1030 nm, 515 nm, 343 nm) usage for modification inscription and various etchants (Hydrofloridic acid, Sodium Hydroxide, Potassium Hydroxide and Sulphuric and Phosphoric acid mixture) comparison. We show that regular SLE etchants such as Hydrofluoric acid or Potassium Hydroxide are unsuitable materials for selective sapphire laser etching. Meanwhile, a 78% sulphuric and 22% phosphoric acid mixture at 270°C temperature is a good alternative for this process. We present the changes in the material after the separate processing steps. Finally, a protocol for advanced sapphire structure formation and a few exemplary structures are presented.

This paper analyses and evaluate the precision and the accuracy the capability of low-cost terrestrial photogrammetry by using many digital cameras to construct a 3D model of an object. To obtain the goal, a building façade has imaged by two inexpensive digital cameras such as Canon and Pentax camera. Bundle adjustment and image processing calculated by using Agisoft PhotScan software. Several factors will be included during this study, different cameras, and control points. Many photogrammetric point clouds will be generated. Their accuracy will be compared with some natural control points which collected by the laser total station of the same building. The cloud to cloud distance will be computed for different comparison 3D models to investigate different variables. The practical field experiment showed a spatial positioning reported by the investigated technique was between 2-4cm in the 3D coordinates of a façade. This accuracy is optimistic since the captured images were processed without any control points.

This paper explores the influence of various camera settings on the quality of 3D reconstructions, particularly in indoor crime scene investigations. Utilizing Neural Radiance Fields (NeRF) and Gaussian Splatting for 3D reconstruction, we analysed the impact of ISO, shutter speed, and aperture settings on the quality of the resulting 3D reconstructions. By conducting controlled experiments in a meeting room setup, we identified optimal settings that minimize noise and artifacts while maximizing detail and brightness. Our findings indicate that an ISO of 200, a shutter speed of 1/60 seconds, and an aperture of f/3.5 provide the best balance for high-quality 3D reconstructions. These settings are especially useful for forensic applications, architectural visualization, and cultural heritage preservation, offering practical guidelines for professionals in these fields. The study also highlights the potential for future research to expand on these findings by exploring other camera parameters and real-time adjustment techniques.

Fabrication of a true-3D inorganic ceramic with resolution down to nanoscale using sol-gel resist precursor is demonstrated. The method has an unrestricted free-form capability, control of the fill-factor, and high fabrication throughput. A systematic study of the proposed approach based on ultrafast laser 3D lithography of organic-inorganic hybrid sol-gel resin followed by a heat treatment enabled formation of inorganic amorphous and crystalline composites guided by the composition of the initial resin. The achieved resolution of 100 nm was obtained for 3D patterns of complex free-form architectures. Fabrication throughput of 50×10³ voxels/s is achieved; voxel - a single volume element was recorded by a single pulse exposure. After a subsequent thermal treatment, ceramic phase was formed depending on the temperature and duration of the heat treatment as validated by Raman micro-spectroscopy. The X-ray diffraction (XRD) revealed a gradual emergence of the crystalline phases at higher temperatures with a signature of cristobalite SiO₂, a high-temperature polymorph. Also, the tetragonal ZrO₂ phase known for its high fracture strength was observed. This 3D nano-sintering technique is scalable from nano- to millimeter dimensions and opens a conceptually novel route for optical 3D nano-printing of various crystalline inorganic materials defined by an initial composition for diverse applications for microdevices in harsh physical and chemical environments and high temperatures.

3D printing has significantly transformed the design and manufacture of robotic prostheses, making these devices more accessible, customized, and functional. This paper examines the historical evolution of prosthetic technology, tracing its development from rudimentary mechanical devices to the integration of advanced technologies, such as 3D printing. This innovation has enabled the production of prostheses at lower costs while enhancing their adaptability and performance. The review highlights how 3D printing has driven a disruptive shift in prosthetic customization, and how emerging technologies—including smart materials and artificial intelligence—have expanded the capabilities of prosthetic devices, offering more adaptive and natural movement. However, challenges persist, particularly regarding the need for standardization and infrastructure expansion to ensure equitable access to these technologies. Future research into novel materials and manufacturing techniques holds the potential to improve further the functionality, affordability, and accessibility of prosthetic devices. In conclusion, while 3D printing has marked a significant milestone in the evolution of robotic prosthetics, overcoming existing challenges is essential to realize its global impact and benefits fully.

While cycling presents environmental benefits and promotes a healthy lifestyle, the risks associated with overtaking maneuvers by motorized vehicles pose significant hindrances for many potential cyclists. Large-scale analysis of overtaking maneuvers could inform traffic researches and city planners on how to reduce these risks by better understanding these maneuvers. Drawing from the fields of sensor-based cycling research and of LiDAR-based traffic data sets, this paper provides a step towards addressing these safety concerns by introducing the Salzburg Bicycle 3d (SaBi3d) data set, consisting of LiDAR point clouds capturing car-to-bicycle overtaking maneuvers. The data set, collected using a LiDAR-equipped bicycle, facilitates detailed analysis of a large quantity of overtaking maneuvers without the need for manual annotation through enabling automatic labeling by a neural network. Additionally, a benchmark result for 3d object detection using a competitive neural network is provided as a baseline for future research. The SaBi3d data set is structured identically to the nuScenes data set, and therefore offers compatibility with numerous existing object detection systems. This work provides valuable resources for future researchers to better understand cycling infrastructure and mitigate risks, thus promoting cycling as a viable mode of transportation.

3D cell cultures have improved the evaluation of drugs for cancer therapy, due to their high similarity to solid tumors. In melanoma, autophagy appears to show a dual role depending on the progression of the disease. p62 protein has been proposed for the evaluation of autophagic flux since its expression is an indicator of the state of autophagy. Pentoxifylline (PTX) and Norcantharidin (NCTD) are drugs that have been shown to have anticancer effects in various types of cancer. In this work, B16F1 mouse melanoma cell line was used, from which two-dimensional (2D) monolayer cultures and three-dimensional (3D) organoids were carried out using the hanging drop technique. The expression of p62 was determined by western blot and immunofluorescences. Our results indicate that pentoxifylline reduces p62 expression in both types of culture. While Norcantharidin increases its expression in 3D cultures at 24 h. Therefore, these drugs could have a potential therapeutic use for the regulation of autophagy in melanoma, depending on the state of evolution of the disease.

Additive manufacturing, commonly referred to as 3D printing, is an exciting and versatile manufacturing technology that is gaining traction and interest in both academic and industrial settings. Polymeric materials are essential components in a majority of the “inks” used across the various 3D printing technologies. As the environmental ramifications of sole or primary reliance on petrochemicals as a resource for industrial polymers continue to manifest themselves at a global scale, a transition to more sustainable bioderived alternatives could offer solutions. In particular, cellulose is promising due to its global abundance, biodegradability, excellent thermal and mechanical properties, and ability to be chemically modified to suit various applications. Thus far, cellulose has typically been incorporated in additive manufacturing applications as a substrate, filler, or reinforcement for other materials. However, due to its versatility and desirable properties, the exploration of all-cellulose 3D printing materials and associated methodologies is increasing. This review will discuss the progress and status of all-cellulose 3D printing approaches, associated challenges, and their potential as a key player in a more sustainable industrial future.

This research presents the creation of a Virtual Reality experience for the Balzi Rossi museum, commemorating the centenary of Prince Albert I Grimaldi's archaeological work at the site. The project, a collaboration between the University of Genoa's 3D Lab Factory, Eurodrone, and the Balzi Rossi archaeological museum, aims to preserve and convey the site's heritage through advanced VR technology. Initially employing Unreal Engine 4, the team used photogrammetry for 3D reconstruction of the "Caviglione" and "Florestano" caves, notable for their ancient rock engravings. This first VR model, despite hardware limitations, provided an interactive exploration of the site. The subsequent development phase utilized Unreal Engine 5, incorporating Nanite technology for enhanced visual fidelity. This advancement resulted in a more detailed and immersive VR experience, presenting the Balzi Rossi cliff across different historical periods, including the Würm glaciation. Key to this phase was optimizing the VR experience for performance, focusing on stable frame rates and minimizing motion sickness, and integrating a multi-lingual interface for broader accessibility. Since November 2023, the VR setup at the Balzi Rossi Museum has been an educational and interactive feature, enabling visitors to explore the site's history virtually. This research demonstrates the potential of VR in cultural heritage preservation and education, providing a foundation for future technological improvements in the field.

When a limb suffers a fracture, rupture, or dislocation, it is traditionally immobilized with plaster. This may induce discomfort in the patient, excessive itching and sweating, which creates the growth of bacteria, leading to an unhygienic and difficulty to keep clean from treatment. Furthermore, if the plaster remains for a long period, it may cause lesions in the joints and ligaments. To overcome all these disadvantages, orthoses have emerged as important medical devices to help patients in rehabilitation, as well as for self-care of deficiencies in clinics and daily life. Traditionally, these devices are produced manually, which becomes time-consuming and error prone. From another point-of-view, it is possible to use imageology (X-ray or computed tomography) to scan the human body; a process that may help orthoses manufacturing but induces radiation to the patient. To overcome this great disadvantage, several types of 3D scanners, without any kind of radiation have emerged. This article describes the use of various types of scanners capable of digitizing the human body, to produce custom orthoses. Studies have shown that photogrammetry is the most used and most suitable 3D scanner for the acquisition of the human body in 3D. With this evolution of technology, it is possible to decrease the scanning time and it will be possible to introduce this technology in clinical environment.

Geotechnical investigation is an important site characterization process in engineering construction. Excavation pits and boreholes are popular geotechnical investigation methods for accessing subsurface soil and rock characteristics. Although they are accurate, they are limited to the discrete locations where tests are carried out. The demand for 3D representation has been increasing as an alternative for improved visualization of geotechnical investigations. This study developed a procedure for 3D modelling of geotechnical investigations using open-source software. It improves 3D visualization of geotechnical investigations and characterization of accuracy and uncertainty assessment. Presently, most geotechnical investigations do not regularly report uncertainty assessment despite its importance in risk analysis of the investigations. The procedure developed in this study was tested in a proposed site for construction of an Inland Container Depot where it depicted geotechnical soil properties with more than 80% accuracy on holdout samples. It was able to model both horizontal and vertical variations of the soil properties with quantification of uncertainty. More testing and wide applications are recommended.

Melanoma is a highly aggressive type of skin cancer produced by malignant transformation of melanocytes and it is usually associated with a poor prognosis. Clinically, melanoma has several stages associated with migration and invasion of the cells through the skin layers, rapid cell spreading and formation of tumors in multiple organs. The main problem is the emergence of resistance of melanoma to the applied methods of treatment, thus it is of primary importance to find more crucial signaling pathways that control the progression of this type of cancer and could be targeted to prevent melanoma spreading. The main life-threatening stage of melanoma is metastasis formation, and 3D cell spheroids are better suited for the study of this process. Using a combinative approach (RT-PCR, immunofluorescence, patch-clamp and calcium imaging) we showed the functional expression of mechanosensitive Piezo1 channels in SK-MEL-2 aggressive melanoma cell line. We found that chemical activation of Piezo1 by its selective agonist Yoda1 completely prevents melanoma spheroid formation, and could be considered as a novel approach for the prevention of melanoma development.

Free-edge effect is one of the factors affecting the mechanical properties of three-dimensional woven composites under tensile load. However, current research is relatively poorly understood regarding the effect of free-edge on the stiffness and strength of the material. This paper aims at examining the influence of free-edge effect on the mechanical properties of 3D woven composites under tension through experimental and simulation mathods. The three-dimensional DIC technique is used to collect the full-field strains on the specimen surface during the test, and the stress-strain differences in different regions in the width direction are analyzed, and the overlap of the curves in each region is found to be high. Experimental studies are conducted on specimens of different widths (within the range of 15-20 mm), and the results indicate that the differences in mechanical properties of 3D woven composites under tension loading in this width range are not significant. A progressive damage finite element model is developed for calculation and compared with experimental results.

The increased accessibility of drone technology and the wide use of Structure from Motion 3D scene reconstruction have transformed the approach for mapping inaccessible slopes undergoing active rockfalls. The Poggio Baldi landslide offers the possibility for many of these techniques to be deployed and integrated with the aim of defining a suitable workflow for the analysis of hazards in mountainous regions. The generation of multitemporal digital slope twins (2016 – 2019), informed a rockfall trajectory analysis that was carried out with a physical-based GIS model. We tested the rockfall scenario reconstructed and calibrated on the analysis of the rock mass characteristics and the geometrical and physical constraints given by the multi-temporal analysis of the SfM point clouds. This time-independent rockfall hazard analysis is a critical component to any subsequent holistic risk analysis on this case study, and any potential similar mountainous setting.

Beyond semantic segmentation,3D instance segmentation(a process to delineate objects of interest and also classifying the objects into a set of categories) is gaining more and more interest among researchers since numerous computer vision applications need accurate segmentation processes(autonomous driving, indoor navigation, and even virtual or augmented reality systems…) This paper gives an overview and a technical comparison of the existing deep learning architectures in handling unstructured Euclidean data for the rapidly developing 3D instance segmentation. First, the authors divide the 3D point clouds based instance segmentation techniques into two major categories which are proposal based methods and proposal free methods. Then, they also introduce and compare the most used datasets with regard to 3D instance segmentation. Furthermore, they compare and analyze these techniques performance (speed, accuracy, response to noise…). Finally, this paper provides a review of the possible future directions of deep learning for 3D sensor-based information and provides insight into the most promising areas for prospective research.

Polystyrene as a thin film on arbitrary substrates or pellets form defective graphene films or powders that can be dispersed in water and organic solvents. The materials were characterized by visible absorption, Raman and X-ray photoelectron spectroscopy, electron and atomic force microscopy and electrochemistry. Raman spectra of these materials show the presence of the expected 2D, G and D peaks at 2750, 1590 and 1350 cm^-1, respectively. The relative intensity of the G vs. the D peak is taken as a quantitative indicator of the density of defects in the G layer.

Osteoarthritis (OA) is a joint disease involving cartilage degeneration. This study aimed to compare properties of chondrocytes from less-affected (LA-Cartilage) and severely-affected (SA-Cartilage) of human OA articular cartilage. Based on Dougados classification, OA cartilage was classified into two groups; less-affected (Grade 0–1) and severely-affected (Grade 2–3). Chondrocytes from each group were cultured until passage (P) 4. Growth, migration, stem cell properties and chondrogenic properties under normal and inflammatory conditions, and the formation of in vitro 3D cartilage tissues were compared between groups. The growth and migratory properties of LA-chondrocytes and SA-chondrocytes were similar, except that the migration rate of SA-chondrocytes was significantly higher at P0 compared to LA-chondrocytes. Both LA-chondrocytes and SA-chondrocytes expressed mesenchymal stem cell markers and tri-lineage differentiation, but the expression of stem cell markers decreased significantly with increasing passage number. Exposure to inflammatory conditions induced distinct morphological changes and significant increases in expression of SOX9 at P4 and MMP3 at P1 for LA-chondrocytes. LA-chondrocytes and SA-chondrocytes able to develop into in vitro 3D constructs, but SA-chondrocytes exhibited superior cartilage-like properties. Chondrocytes from both less- and severely-affected regions are suitable to be used in clinical applications, however, chondrocytes from severely-affected regions could be a more favorable cell source.

Numerical weather prediction is an initial-value problem, for determination of the initial conditions, there are many methods and one of the most classical methods is variational methods in three dimensions, or 3D-Var. In this approach, with a defined cost function proportional to the square of the distance between the analysis and both the background and the observations, one can obtain the analysis. In the cost function, the background and the observations are reshaped to vectors; within this step, the order of the background error covariance matrix and the observational error covariance matrix becomes huge, which is not convenient to one to obtain the analysis. In this paper, according to the matrix analysis approach, we put forward some possible improvements to the dimension-reduction algorithm of 3D-Var, so that provide some references for data assimilation.

Background: Wilms tumor (WT) is the main renal tumor in children. SIOP-UMBRELLA Guidelines admit Nephron sparing surgery (NSS) in syndromic patients, and in small (&lt;300 ml) nonsyndromic unilateral WTs, without lymph node involvement, and with a substantial expected remnant renal function, after neoadjuvant chemotherapy. We report our prechemotherapy transperitoneal robot-assisted partial nephrectomy (RAPN) in a unilateral non-syndromic Wilms tumor. Methods: A 6-year-old-child showed an exophytic 3.6 cm diameter solid rounding mass involving the upper right renal pole at an incidental abdominal echotomography. CT-scan and abdominal MRI proved no local infiltration neither lymph node involvement was appreciated, suggesting an exophytic mass easily resectable through a NSS robotic approach, with a low risk of rupture and no subverted renal anatomy. The preoperative imaging was not suggestive for WT. A virtual 3D reconstruction of the tumor was performed. Results: the oncologic board approved a robot-assisted partial nephrectomy with the intraperitoneal approach. The histopathologic analysis displayed a WT. The patient underwent 10 vincristine-doses adjuvant chemotherapy. 28-months follow-up showed no tumor recurrence. Conclusions: Intraperitoneal RAPN can represent an opportunity for WT and needs to be assessed as a challenging possibility. This case suggests a potential role of prechemotherapy RAPN in the near future for highly selected patients.

In this paper, we present the idea of Self Supervised learning on the Shape Completion and Classification of point clouds. Most 3D shape completion pipelines utilize autoencoders to extract features from point clouds used in downstream tasks such as Classification, Segmentation, Detection, and other related applications. Our idea is to add Contrastive Learning into Auto-Encoders to learn both global and local feature representations of point clouds. We use a combination of Triplet Loss and Chamfer distance to learn global and local feature representations. To evaluate the performance of embeddings for Classification, we utilize the PointNet classifier. We also extend the number of classes to evaluate our model from 4 to 10 to show the generalization ability of learned features. Based on our results, embedding generated from the Contrastive autoencoder enhances Shape Completion and Classification performance from 84.2% to 84.9% of point clouds achieving the state-of-the-art results with 10 classes.

Electric energy has become essential nowadays not only for the daily life of each of us but also for the economy of different countries. The dissemination of geographic information plays an important role in national development as it facilitates communication between managers, investors, and consumers in this sector. Since the management of electricity network data was previously done in Tunisia based on paper maps and plans, the purpose of this article is to present a case of planning based on GIS, Web, and 3D Web GIS, which would have significant positive consequences on this sector from a technical and financial sides with an improvement in customer satisfaction and the creation of an intelligent electricity network which will be a real decision-making tool. This work draws up an inventory of the network MV (Medium Voltage)/LV (Low Voltage) of the region of Medjez El Bab which routes electricity to the big centers of consumption with access to MV/LV subscribers. The analysis of the network's impedance allowed carrying out different scenarios to optimize performance and obtain more realistic routes. Many thematic maps were produced as part of this project (Slope map, Land use map, map of the MV voltage domains, map of the MV/LV transformer stations power, etc.). A three-dimensional virtual city has been developed to visualize the graphical and attribute data for the study area. A Web and 3D Web GIS applications that allows the publication of the interactive maps on the Web as well as the database information have been developed to offer users the possibility of consulting the produced products by internet. Finally, a website related to the study was developed.

A pilot study on laser 3D printing of inorganic free-form micro-optics is experimentally validated. Ultrafast laser nanolithography is employed for structuring hybrid organic-inorganic material SZ2080TM followed by high-temperature calcination post-processing. The combination allows production of 3D architectures and the heat-treatment results in converting the material to inorganic substance. The produced miniature optical elements are characterized and their optical performance demonstrated. Finally, the concept is validated for manufacturing compound optical components such as stacked lenses. This is opening for new directions and applications of laser made microoptics under harsh conditions such as high intensity radiation, temperature, acidic environment, pressure variations, which include open space, astrophotonics, and remote sensing.

Recent advances in the research area of 3D magnetic topological solitons (hopfions) in restricted geometries are reviewed. The description of the magnetic solitons is based on macroscopic micromagnetic approach and the Landau-Lifshitz equation of the magnetization motion. The concepts of the gauge emergent vector potential and emergent magnetic field are widely used to calculate 3D topological charge (the Hopf index) of magnetic textures. The relation of the magnetic hopfions with classical field theory is demonstrated and a special role of the curvilinear toroidal coordinates in description of the hopfions is underlined. The hopfion stability and dynamics in ferromagnetic films and dots are considered. Some critical discussion of calculations of the magnetization emergent magnetic field and the Hopf index of the toroidal magnetic hopfions in restricted geometries is presented.

Diabetes is a major health concern that the next-generation of on-demand insulin releasing implants may overcome for personalized therapy. Therein, 3D-printed phenylboronic acid-containing subcutaneous implants with on-demand glucose-triggered drug release abilities are produced using high resolution stereolithography technology. To that end, the methacrylation of phenylboronic acid is targeted following a two-step reaction. The resulting photocurable phenylboronic acid derivative is accordingly incorporated within bioinert polyhydroxyethyl methacrylate-based hydrogels at varying loadings. The end result are sub-centimeter scaled 3D-printed bionert implants that can be remotely activated with 1,2-diols and 1,3-diols such as glucose for on-demand drug administration such as insulin. As a proof of concept, varying glucose concentration from hypoglycemia to hyperglycemia levels readily allow the release of pinacol, i.e. a model molecule with similar release properties than insulin, at respectively low and high rates. In addition, the results demonstrated that adjusting the geometry and size of the 3D-printed part is a simple and suitable method for tailoring the release behavior and dosage.

In the world of digital avatars, three-dimensional (3D) human models are utilized to replicate real-world appearance and movements with a higher degree of realism compared to traditional 2D representations. Currently, extensive person-specific data capturing and 3D artists are required to create photorealistic avatars of existing people. Determining the 3D pose and articulation of an avatar from 2D images requires complex algorithms, a capability commonly found in the Visual Effects (VFX) industry but not readily available elsewhere. Hence, this study proposes an approach to generate 3D avatar from a 2D image of a person with uncanny resemblance and an accurate depiction of the subject’s likeness. The proposed approach, PIFu+CycleGAN, combines Pixel-aligned Implicit Function (PIFu) and cycleGAN for textured avatar construction. PIFu is specifically used to capture intricate details and arbitrary topology. Additionally, the hourglass architecture-based module is utilized for T-pose estimation for predicting the initial geometry and shape. Evaluating the proposed approach on the benchmark RenderPeople dataset, it outperforms the state-of-the-art models with values of 1.53 and 1.50 for the Chamfer and P2S distance, respectively. This indicates the creation of high-quality 3D meshes with promising textures, which are of exceptional quality and suitable for animation.

In the history, architects, engineers or artists traditionally visualized architectural, urban planning, urban design, or landscape design projects with physical models in a smaller scale to represent their ideas. The biggest problems of traditional materialistic models are the long production time and limitation of mobility. Thanks to advancements in digital technology, 3D models can now be generated easily from 2D blueprints using computer software. However, eventually the digitalized approach could not replace the whole industry of making physical models, because of a lack of stereoscopic 3D imaging of space and structures. In this study, we discuss two points: the normal procedure of visualizing 3D models in urbanism and architecture design projects; and proposal of the stereographic hologram visualization for 3D models created with CHIMERA hologram printer as a new approach to solve all the problems in spatial projects visualization of both digitalized and physical models. The experiment's results indicate that tabletop holograms' visualization quality can potentially replace traditional methods in the near future. Moreover, the input data for this method can be seamlessly integrated into current architectural and urban design workflows, making holograms a promising approach for 3D immersive content in this field.

The evaluation of nanostructured biomaterials and medicines is associated with 2D cultures that provide insight into the biological mechanisms at the molecular level, while critical aspects of the tumor microenvironment (TME) are provided by the study of animal xenograft models. More realistic models that can histologically reproduce human tumors are provided by tissue engineering methodologies of co-culturing cells of varied phenotypes, to provide 3D tumor spheroids that recapitulate the dynamic TME in 3D matrices. The novel approaches of 3D tumor models are combined with tumor tissue engineering (TTE) scaffolds including hydrogels, bioprinted materials, decellularized tissues, fibrous and nanostructured matrices. This review focuses on the use of nanostructured materials in cancer therapy and regeneration, and the development of realistic models for studying TME molecular and immune characteristics. Tissue regeneration is an important aspect of TTE scaffolds for restoring the normal function of the tissues, while providing cancer treatment. Thus, this article reports recent advancements on the development of 3D TTE models for antitumor drug screening, studying of tumor metastasis, and tissue regeneration. Also, this review identifies the great opportunities of 3D TTE scaffolds in the evaluation of the immunological mechanisms and processes involved in the application of immunotherapies.

A detailed review of the scientific literature was undertaken to examine the most recent developments in plasma processing in the field of medicine. The first part of the review includes a detailed breakdown of the different types of coatings that can be applied onto medical devices using plasma, with a specific focus on antimicrobial surfaces. The developments during 2023 in plasma deposited biocompatible, drug delivery and adhesive coatings are described and specific applications in additive manufacturing are highlighted. The use of plasma and plasma activated liquids as standalone therapeutics continues to evolve and pertinent advances in this field are described. In addition, the combination of plasma medicine with conventional pharmaceutical interventions was reviewed and key emerging trends were highlighted, including the use of plasma to enhance drug delivery directly into tissue. The potential synergies between plasma medicine and chemotherapeutics for oncology and infection treatment is a growing area and recent advancements are noted. Finally, the use of plasma to control excess antibiotics and to intentionally degrade such materials in waste streams is described.

Immediate load of full-arch rehabilitations over implants, specially over 4 implants are very well documented in the literature. More recently, the use of computed surgical guides to help the planning and the execution of these treatments, in many situations without the need of raising a flap, and diminishing the appearance of hematomas, bleeding and with less trauma to the patient has gained preference among implantologists. The objective of this case report is to show a clinical case of an immediate load full-arch fixed rehabilitation over 4 implants produced by 3D printing manufacturing technology, and placed with a computed surgical guide, in the same appointment, and the 24 months follow-up. The patient returned after 3 months to replace the immediate temporary fixed prosthesis for a new one, with metallic bar, better teeth and more delicate. Soft and hard tissue around the implants seemed to be stable, without signs of inflammation, either on the 3 or the 24 months follow-up. 3D printing of implants by direct metal laser sintering is a technology that seems to be promising for oral implantology, with solid studies showing reliable results, as seen in this single case. More clinical studies are necessary to testify its efficacy.

Characters are one of the most important elements in composing digital animation. The appear-ance and voice of a character should be designed to express the personality and values of the character. However, it is not easy for animation producers to harmoniously match the appear-ance and voice of a character. Advances in deep learning technology have made it possible to overcome this limitation. To achieve this, firstly, an audio-visual dataset of characters is required. In this study, we construct and verify a Korean audio-visual dataset consisting of frontal face im-ages of various characters and short voice clips. We developed an application that can automati-cally extract the frontal face image and a short voice clip of a character by collecting videos up-loaded to YouTube. Through this, a dataset consisting of a total of 1,522 face images and a total of 7,999 seconds of voice clips was built based on 490 characters. Furthermore, we automatically la-bel characters by gender and age to validate the dataset. The dataset built in this study is expected to be used in various deep learning fields, such as classification, generative adversarial networks, and speech synthesis.

The 3D reconstruction of vermiculite-based sealing material was carried out based on CT scanning experiments and Avizo software. The precision and representation of the reconstructed digital core were tested by calculating the pore structure parameters and comparing them with the experimental results of mercury compression. Avizo is a perfect interface with Fluent software to perform micro-scale seepage simulation to explore the distribution of pressure and velocity fields during fluid transport. In this paper, a new approach is proposed to study the penetration leakage of non-metallic gaskets by using equivalent pore networks.

The three-dimensional Ising model on the m$\times$n$\times$l cubic lattice with the screw boundary condition along the ${\bf X}$ direction and the periodic boundary conditions along both ${\bf Y}$ and ${\bf Z}$ directions is exactly solved by using the $2^{mn}$-dimensional representation of the rotation group in $2mn$-dimensions, similar to the Kaufman's spinor approach in two dimensions. The exact partition function is obtained from two sets of $2^{mn-1}$ eigenvalues of the $2^{mn}$-dimensional transfer matrix {\bf V} corresponding to the even and odd eigenvectors, respectively. Such the eigenvalues are determined by the angles of the 2mn-dimensional rotation associated with {\bf V}.

In this article, metallic additive manufacturing (AM) processes were classified and demonstrated. AM technology can be applied to a wide range of industrial areas because of its great feasibility in the design and manufacturing of various complex parts. The main factor that distinguishes various metallic AM processes from each other is the deposition method. Deposited metal can be imported in the form of melt or semi-solid. AM technology also covers a wide range of materials like aluminum, titanium, and many other alloys. Some of the common applications of metallic AM processes are the quick manufacturing of the parts which utilized in various industries like medical, automotive, aerospace, and jewelry industries. AM can help to fabricate parts that are impossible to be manufactured by other processes.

Existing methods for 3D human pose estimation mainly divide the task into two stages. The first stage identifies the 2D coordinates of the human joints in the input image, namely the 2D human joint coordinates. The second stage uses the results from the first stage as input to recover the depth information of human joints from the 2D human joint coordinates to achieve 3D human pose estimation. However, the recognition accuracy of the two-stage method relies heavily on the results of the first stage and includes too many redundant processing steps, which reduces the inference efficiency of the network. To address these issues, we propose the EDD, a fully End-to-end 3D human pose estimation method based on transformer architecture with Dual Decoders. By learning multiple human poses, the model can directly infer all 3D human poses in the image using a pose decoder, and then further optimize the recognition result using a joint decoder based on the kinematic relations between joints. With the attention mechanism, this method can adaptively focus on the most relevant features to the target joint, effectively overcoming the feature misalignment problem in the human pose estimation task and greatly improving the model performance. Any complex post-processing step, such as non-maximum suppression, is eliminated, further improving the efficiency of the model. The results show that the method achieves an accuracy of 87.4% on the MuPoTS-3D dataset, significantly improving the accuracy of end-to-end 3D human pose estimation methods.

The rapid development of electrochemical CO2 reduction offers a promising route to convert in-termittent renewable energy into products of high value-added fuels or chemical feedstocks. However, low faradaic efficiency, low current density, and a narrow potential range still limited the large-scale application of CO2RR electrocatalyst. Herein, monolith 3D bi-continuous nano-porous Bismuth (np-Bi) electrodes are fabricated via a simple one-step electrochemical dealloying strategy from Pb-Bi binary alloy. The unique bi-continuous porous structure ensures highly effective charge transfer, meanwhile the controllable millimeter-size geometric porous structure enables easy catalyst adjustment to expose highly suitable surface curvatures with abundant reactive sites. This results in a high selectivity of 92.6% and superior potential window (400 mV, selectivity >88%) for electrochemical reduction of carbon dioxide to formate. Our scalable strategy provides a feasible pathway for mass-producing high-performance and versatile CO2 electrocatalysts.

A key component of efforts to identify the biological and drug-specific aspects that contribute to therapeutic failure or unexpected exposure-associated toxicity is the study of drug-intestinal barrier interactions. While methods supporting such assessments are widely described for human therapeutics, there is relatively little information available for similar evaluation in support of veterinary pharmaceuticals. There is, therefore, a critical need to develop novel approaches for evaluating drug-gut interactions in veterinary medicine. Three-dimensional (3D) organoids can address these difficulties in a reasonably affordable system that circumvents the need for more invasive in vivo assays in live animals. However, a first step in the development of such systems is understanding organoid interactions in a 2D monolayer. Given the importance of orally administered medications for meeting the therapeutic need of companion animals, we demonstrate growth conditions under which canine colonoid-derived intestinal epithelial cells survive, mature, and differentiate into confluent cell systems with high monolayer integrity. We further examine the applicability of this canine colonoid-derived 2D model to assess the permeability of three structurally diverse, passively absorbed β-blockers (e.g., propranolol, metoprolol, and atenolol). Both absorptive and secretive apparent permeability (Papp) of these drugs at two different pH conditions were evaluated in canine colonoid-derived monolayers and were compared with that of Caco-2 cells. This proof-of-concept study provides promising preliminary results with regard to the utility of canine-derived organoid monolayers for species-specific assessments of therapeutic drug passive permeability.

Smart health applications have received significant attention in recent years. Novel applications hold significant promise to overcome many of the inconveniences faced by persons with disabilities throughout daily living. For people with blindness and low vision (BLV), environmental perception is compromised, creating myriad difficulties. Precise localization is still a gap in the field and is critical to safe navigation. Conventional GNSS positioning cannot provide satisfactory performance in urban canyons. 3D mapping-aided (3DMA) GNSS may serve as an urban GNSS solution, since the availability of 3D city models has widely increased. As a result, this study developed a real-time 3DMA GNSS-positioning system based on state-of-the-art 3DMA GNSS algorithms. Shadow matching was integrated with likelihood-based ranging 3DMA GNSS, generating positioning hypothesis candidates. To increase robustness, the 3DMA GNSS solution was then optimized with Doppler measurements using factor graph optimization (FGO) in a loosely-coupled fashion. This study also evaluated positioning performance using an advanced wearable system’s recorded data in New York City. The real-time forward processed FGO can provide a root-mean-square error (RMSE) with about 21 m. The RMSE drops to 16 m when the data is post-processed with FGO in a combined direction. Overall results show that the proposed loosely-coupled 3DMA FGO algorithm can provide a better and more robust positioning performance for the multi-sensor integration approach used by this wearable for persons with BLV.

Along with the popularity of the Internet, people are exposed to more and more ways of micro-videos, and a huge amount of micro-video data has emerged. micro-videos have gradually become the Internet content preferred by the public, and a large number of micro-video apps have also emerged, such as Tiktok and Kwai. Intelligent classification and mining of micro-videos can greatly enhance user experience, improve business operation efficiency and enhance user experience. Through deep intelligent analysis and mining of micro-videos, important information in micro-videos can be extracted to provide an important basis for beautifying videos, content appreciation, video recommendation, content search, etc. In the past, content understanding for short videos often used human work annotation, but in recent years, with the great success of deep convolutional neural networks in image recognition, short video content understanding based on this method has gradually developed. Nowadays, most recognition algorithms extract the feature representation of each frame independently and then fuse them. However, while extracting the feature representation, some low-level semantic features are lost, which makes the algorithm unable to accurately distinguish the category of the video. At present, the algorithm of micro-video recognition based on deep learning has surpassed the iDT algorithm, making these traditional methods fade out of people’s view. In this paper according to the micro-video classification task, a new network model is proposed to concatenate features of each modality into the overall features of various modalities through the network, and then fuse the various modal features with the attention mechanism to obtain the whole micro-video features, which will be used for classification. In order to verify the effectiveness of the algorithm proposed in this paper, experiments are conducted in the public dataset, and it is shown the effectiveness of our model.

This article describes the methodology used to identify the mathematical model that describes the correlations between the input parameters of an experiment and the parameters being followed. As a technological process, the aerodynamic separation was chosen, respectively, the behavior of a solid particle within an ascending vertical airflow. The experimental data obtained were used to identify two parameters, the average linear velocity, and the angular velocity, and through the Table Curve 3D program was developed a mathematical model which describes the dependence between the input parameters (the shape and size of the solid particle and the velocity of the airflow) and the monitored parameters. In order to determine a single mathematical equation that describes as accurately as possible the correlation between the input variables and those obtained, a pyramid-type analysis was designed. The determination of the mathematical equation started from the number of equations generated by the Table Curve 3D program, then the equations with a correlation coefficient greater than 0.85 were chosen, and finally, the common equations were identified. Respecting the working methodology was identified one equation which has for the average linear velocity a correlation coefficient r2 between 0.88-0.99 and 0.86-0.99 for the angular velocity.

Radar observation data with high temporal and spatial resolution are used in the data assimilation experiment to improve precipitation forecast of a numerical model. The numerical model considered in this study is Weather Research and Forecasting (WRF) model with double-moment 6-class microphysics scheme (WDM6). We calculated radar equivalent reflectivity factor using higher resolution WRF and compared with radar observations in South Korea. To compare the precipitation forecast characteristics of three-dimensional variational (3D-Var) assimilation of radar data, four experiments are performed based on different precipitation types. Comparisons of the 24-h accumulated rainfall with Automatic Weather Station (AWS) data, Contoured Frequency by Altitude Diagram (CFAD), Time Height Cross Sections (THCS), and vertical hydrometeor profiles are used to evaluate and compare the accuracy. The model simulations are performed with and with-out 3D-VAR radar reflectivity, radial velocity and AWS assimilation for two mesoscale convective cases and two synoptic scale cases. The radar data assimilation experiment improved the location of precipitation area and rainfall intensity compared to the control run. Especially, for the two convective cases, simulating mesoscale convective system was greatly improved.

The initial stability after implantology is paramount to the survival of the dental implant and the surface roughness of the implant plays a vital role in this regard. The characterisation of surface topography is a complicated branch of metrology, with a huge range of parameters available. Each parameter contributes significantly towards the survival and mechanical properties of 3D-printed specimens. The purpose of this paper is to experimentally investigate the effect of surface roughness of 3D-printed dental implants and 3D-printed dogbone tensile samples under areal height (Ra) parameters, amplitude parameters (average of ordinates), skewness (Rsk) parameters and mechanical properties. During the experiment, roughness values were analysed and the results showed that the skewness parameter demonstrated a minimum value of 0.596%. The 3D-printed dental implant recorded Ra with a 3.4 mm diameter at 43.23% and the 3D-printed dental implant with a 4.3 mm diameter at 26.18%. Samples with a complex geometry exhibited a higher roughness surface, which was the greatest difficulty of additive manufacturing when evaluating surface finish. The results show that when the ultimate tensile stress (UTS) decreases from 968.35 MPa to 955.25 MPa, Ra increases by 1.4% and when UTS increases to 961.18 MPa, Ra increases by 0.6%. When the cycle decreases from 262142 to 137433, Ra shows that less than a 90.74% increase in cycle is obtained. For 3D-printed dental implants, the higher the surface roughness, the lower the mechanical properties, ultimately leading to decreased implant life and poor performance.

Three-dimensional (3D) printing techniques have received considerable focus in the area of bone engineering due to its precise control in the fabrication of complex structures with customizable shapes, internal and external architectures, mechanical strength, and bioactivity. In this study, we design a new composition biomaterial consisting of polylactic acid (PLA), and halloysite nanotubes (HNTs) loaded with zinc nanoparticles (PLA+H+Zn). The hydrophobic surface of the 3D printed scaffold was coated with two layers of fetal bovine serum (FBS) on the sides and one layer of NaOH in the middle. Additionally, a layer of gentamicin was coated on the outermost layer against bacterial infection. Scaffolds were cultured in standard cell culture medium without the addition of osteogenic medium. This surface modification strategy improved material hydrophilicity and enhanced cell adhesion. Pre-osteoblasts cultured on these scaffolds differentiated into osteoblasts and proceeded to produce a type I collagen matrix and subsequent calcium deposition. 3D printed scaffolds formed from this composition possessed high mechanical strength and showed an osteoinductive potential. Furthermore, the external coating of antibiotics not only preserved the previous osteogenic properties of the 3D scaffold but also significantly reduced bacterial growth. Our surface modification model enabled the fabrication of a material surface that was hydrophilic and antibacterial, simultaneously, with an osteogenic property. The designed PLA+H+Zn may be a viable candidate for the fabrication of customized bone implants.

Paclitaxel is a natural, highly lipophilic anti proliferative drug widely used in medicine. We have studied the release of tritium-labeled paclitaxel (³H-PTX) from matrices destined for the coating of vascular stents and produced by the electrospinning method from the solutions of polycaprolactone (PCL) with paclitaxel (PTX) in hexafluoisoropropanol (HFIP) and/or solutions of PCL with PTX and human serum albumin (HSA) in HFIP or HIFP-dimethyl sulphoxide (DMSO) blend. The release of PTX has been shown to depend on the solvent and the composition of electrospinning solution, as well as the composition of the surrounding medium, particularly the concentration of free PTX and PTX-binding biomolecules present in human serum. It was shown that 3D matrices can completely release PTX without weight loss. Two-phase PTX release from optimized 3D matrices was obtained: ~27% of PTX was released in the first day, another 8% were released over the next 26 days. Wherein ~2.8%, ~2.3%, and ~0.25% of PTX was released on day 3, 9, and 27, respectively. Considering PTX toxicity, the rate of its diffusion through the arterial wall, and the data obtained the minimum cytostatic dose of the drug in the arterial wall will be maintained for at least three months.

AbstractWhile the technology is relatively new, low cost 3D printing has impacted many aspects of human life. 3D printers are being used as manufacturing tools for a wide variety of devices in a spectrum of applications ranging from diagnosis to implants to external prostheses. The ease of use and availability of 3D design software and low cost has made 3D printing an accessible manufacturing and fabrication tool in many research laboratories. 3D printers can print materials with varying density, optical character, strength and chemical properties providing platforms for a huge number of strategies that can be chosen for user’s needs. In this review, we focus on applications in biomedical diagnostics and how this revolutionary technique is facilitating development of low cost, sensitive and often geometrically complex tools. 3D printing in fabrication of microfluidics, supporting equipment, optical and electronic components of diagnostic devices is presented. Emerging diagnostic 3D bioprinting as a tool to incorporate living cells or biomaterials into 3D printing is also discussed.

This study aimed to assess the response of 3D printed PLA scaffolds biomimetically coated with apatite on human primary osteoblast spheroids and evaluate the biological response to its association with Bone Morphogenetic Protein 2 (rhBMP-2) in rat calvaria. PLA scaffolds were produced via 3D printing, soaked in simulated body fluid (SBF) solution, and characterized by physical-chemical, morphological, and mechanical properties. The in vitro biological response was assessed with human primary osteoblast (HOb) spheroids. The in vivo analysis was conducted through the implantation of 3D printed PLA scaffolds either alone, covered by apatite (PLA-CaP) or PLA-CaP loaded with rhBMP-2 (PLA-CaP+rhBMP-2) on critical-sized defects (8 mm) of rat calvaria. Increased cell adhesion and in vitro release of growth factors (PDGF, bFGF, VEGF) was observed for PLA-CaP scaffolds when pre-treated with FBS. PLA-CaP+BMP2 presented higher values of newly formed bone (NFB) than other groups at all experimental periods (p&lt;0.05), attaining 44.85% of NFB after 6 months. These findings indicate that functionalization of PLA scaffolds with biomimetic apatite can improve its biological properties in the presence of complex biological media. Its association with BMP2 may enhance bone repair, suggesting this strategy as a promising candidate for bone tissue engineering.

Currently, the number of approved veterinary medicines are limited, and human medications are used off-label. These approved human medications are of too high potencies for a cat or a small dog breed. Therefore, there is a dire demand for smaller doses of veterinary medicines. This study aims to investigate the use of three semi-solid extrusion 3D printers in a pharmacy or animal clinic setting for extemporaneous manufacturing of prednisolone containing orodispersible films for veterinary use. Orodispersible films with adequate content uniformity and acceptance values defined by the European Pharmacopoeia was produced with one of the studied printers, namely, the Allevi 2 bioprinter. Smooth and flexible films, with high mechanical strength, neutral pH, and low moisture content were produced with high correlation between prepared design and obtained drug amount, indicating that the Allevi 2 printer could successfully be used to extemporaneously manufacture personalized doses for animals at the point-of-care.

Direct laser writing three-dimensional nano-lithography is an established technique for manufacturing functional 3D micro- and nano-objects via non-linear absorption induced polymerization process. In this Chapter an underlying physical mechanisms taking place during nano-confined polymerization reaction, induced by tightly focused ultra-short laser pulses, are reviewed and discussed. The special attention is paid on the effects that directly impact structuring resolution and minimum achievable feature size. Analysis of possible photo-initiation mechanisms as contributing multi-photon absorption and avalanche ionization in pre-polymers under diverse exposure conditions (wavelength, pulse duration) is presented. Feasible structuring of pure (non-photosensitized) and functional nanoparticles doped polymer precursors is justified and benefits of such materials/structures for microoptics, photonics and cell scaffolds are highlighted. The influence of temperature effects (induced by writing process itself or determined by ambient conditions) on polymerization process, observed in different pre-polymers under diverse exposure regimes is outlined. The further adjustment of the structuring resolution is possible via precise control of light polarization and diffusion assisted radical quenching. The work is concluded with a brief outlook on future challenges and perspectives related to refinement of 3D ultra-fast laser lithography fabrication process in the means of application of diverse post-processing methods and research into novel photo-curable materials including inorganic ones.

3D meso-scale structures that can reach up to centimeters in overall size but retain micro- or nano-features, proved to be promising in various science fields ranging from micro-mechanical metamaterials to photonics and bio-medical scaffolds. In this work we present synchronization of the linear and galvano scanners for efficient femtosecond 3D optical printing of objects at the meso-scale (from sub-μm to sub-cm spanning five orders of magnitude). In such configuration the linear stages provide stitch-free structuring at nearly limitless (up to tens-of-cm) working area, while galvo-scanners allow to achieve translation velocities in the range of mm/s-cm/s without sacrificing nano-scale positioning accuracy and preserving undistorted shape of the final print. The principle behind this approach is demonstrated, proving its inherent advantages in comparison to separate use of only linear stages or scanners. The printing rate is calculated in terms voxels/s, showcasing the capability to maintain an optimal feature size while increasing throughput. Full capabilities of this approach are demonstrated by fabricating structures that reach millimeters in size but still retain μm-scale features: scaffolds for cell growth, microlenses and photonic crystals. All this is combined into a benchmark structure: a meso-butterfly. Provided results show that synchronization of two scan modes is crucial for the end goal of industrial-scale implementation of this technology and makes the laser printing well aligned with similar approaches in nanofabrication by electron and ion beams.

Central composite design (CCD) is a methodology that utilizes experimental conditions based on the combination of variable points to be studied. This study aimed to select a hydrogel from the combinations provided by CCD for 3D bioprinting applications. Three biopolymers were chosen: sodium alginate (SA), gelatin (GEL), and carboxymethylcellulose (CMC), and their maximum and minimum concentrations were defined. After CCD provided the suggested combinations, the hydrogels were mixed and analyzed for their swelling degree (SD) in phosphate buffer saline (PBS) and Dulbecco's modified Eagle medium (DMEM), and printability was assessed in 2D and 3D assays. The hydrogel with the concentrations of 7.5%, 7.5%, and 2.5% for SA, GEL, and CMC, respectively, was chosen for presenting the highest SD in both fluids and good printability parameters in manual and 3D printer-based extrusion. This study demonstrated the potential utilization of Design of Experiments (DoE) methodologies to assist the development of hydrogels for 3D bioprinting purposes.

Human Papillomavirus (HPV) related cancers account for a large percentage of cancers. The tumor microenvironment (TME) is a complex structure and contributes significantly to tumor development, progression, and invasion. The TME is particularly pronounced in HPV-related cancers and HPV is known to influence the TME. In cancer research, there is an urgent need for new models to deepen our understanding of the pathophysiology of the disease and to facilitate the development of innovative therapies. In this context, 3D cell culture has emerged as a promising method in cancer research, that offers significant potential compared to conventional approaches. 3D modelling can produce results that are more consistent with clinical outcomes without the ethical concerns and problems of animal models. In this review, our aim is to discuss the tumor microenvironment in HPV-related cancers and demonstrate the importance of advancing 3D cell culture models for this purpose.

This case study originates as a design experiment for a sustainable housing system built on-site. The context is Niamey, the capital of Niger. The study takes into account the environmental issues in the construction sector and aims to find a solution capable of meeting housing, environmental, and economic needs. In the field of earthen construction, the most important developments have been achieved in manufacturing methods. In particular, the use of an additive digital manufacturing system, such as large-scale 3D-printing, allows the construction of complex shapes derived from structural and thermal studies, maintaining a high degree of automation in the construction process, reducing construction times and labor costs. This paper investigates the possibility of responding to housing and environmental needs with a settlement system made almost entirely of printed earth, maintaining the highest possible degree of automation. Starting from a study on the state of the art of 3D-printing in architecture and printable earthen compounds, the design choices of similar cases are analyzed to understand the construction techniques, potentials, and limitations of the medium. Finally, a design proposal is developed based on the definition of a fully printable functional module, which, upon aggregation, determines the characteristics of the final settlement. This implies a radical change of approach compared to previous prototyping of 3D-printed earthen buildings, as the design of the single functional module is not an exercise that finds completion in itself, but is oriented to the scale of the settlement right from the definition of its basic geometric characteristics. In other words, the settlement is no longer the result of the serial aggregation of independent basic units, but arises spontaneously from the juxtaposition of functional modules designed to interact with each other and merge into a single residential complex. The settlement is therefore the large-scale replication of the alternation between full and empty spaces that characterizes the single functional module and, even more importantly, the replication can take multiple forms. In fact, the full and empty spaces of the functional module are planned to allow multiple combinations of aggregation. This introduces a certain degree of customization into the growth dynamics of the settlement, a factor that is entirely new compared to previous proposals by repeatable modules. No less important are the environmental implications, as designing for the scale of the settlement allows the low carbon footprint typical of earth-based construction to be extended from the single building to the entire settlement.

Additive manufacturing (AM), commonly known as 3D printing, has emerged as a transformative technology in supply chain management (SCM). This abstract explores how AM influences various aspects of SCM, including inventory management, production processes, and logistics. By enabling on-demand production and reducing reliance on traditional manufacturing methods, AM minimizes inventory costs and enhances customization capabilities. It also facilitates localized production, which can reduce lead times and transportation costs. The integration of AM into SCM fosters greater flexibility and resilience, allowing businesses to respond more swiftly to market changes and disruptions. This study highlights both the opportunities and challenges associated with adopting AM, emphasizing the need for strategic adjustments to fully leverage its potential in modern supply chains.

Bladder cancer (BC) is one of the most lethal genitourinary malignancies owing to its propensity for recurrence and poor survival. The biochemical pathway, signal transducer and activator of transcription 3 (STAT3), has gained significance as a molecular pathway that promotes proliferation, invasion, and chemoresistance. In this study, we explored the targeting of STAT3 with TTI-101 and SH5-07 in bladder cancer (BCa) and elucidated the mechanisms in three-dimensional (3D) spheroid and tumoroid models. We optimized the growth of spheroids from human, rat, and mouse BCa cell lines (J82, NBT-II, and MB49, respectively), and tumoroids from BBN (N-butyl-N-(4-hydroxybutyl)-nitrosamine) induced rat bladder tumors. Cell viability was assessed using MTT and trypan blue assays. ATP production, ROS production, and calcium AM (CA)/EtBr staining were used to measure the spheroid and organoid inhibition and mitochondrial function. Western blot analysis was performed to evaluate the pharmacodynamic markers involved in cell proliferation, apoptosis, cancer stem cells (CSCs), and STAT3 signaling in BCa. We found that targeting STAT3 (using TTI-101 and SH5-07) significantly reduced the proliferation of BCa spheroids, and tumoroids, which was accompanied by decreased expression of pSTAT3, Cyclin D1, and PCNA. Our data also demonstrated that treatment with STAT3 inhibitors induced ROS production and cell death in BCa spheroids and organoids. STAT3 inhibition induced cell death was associated with the activation of caspase 3/7 and PARP cleavage. Moreover, TTI-101 and SH5-07 targets cancer stem cells by downregulating the expression of CD44 and CD133 in 3D models. This study provides the first evidence for the prevention of bladder cancer with small-molecule inhibitors TTI101 and SH5-07 via suppression of CSCs and STAT3 signaling.