The weakness of the dispersion-managed link combined with optical phase conjugation to compensate for optical signal distortion caused by chromatic dispersion and nonlinear Kerr effect of standard single mode fiber is its limited structural flexibility. We propose dispersion map that can simultaneously compensate for the distorted wavelength division multiplexed signal while increasing the configurational flexibility. Each residual dispersion per span (RDPS) in the former half of the proposed link is randomly determined, and in the latter half, the arrangement order of RDPS is the same as or inverted in the former half. We confirm that the dispersion maps in which the RDPS distribution pattern in the latter half is opposite to the arrangement order in the former half are more effective in compensation, and rather, the compensation effect is better than in the dispersion map of the conventional scheme. The notable result of this paper is that the increase of flexibility can be achieved through random arrangement of RDPS in the former half, and the compensation improvement can be achieved by through inverse arrangement in the latter half which make the distribution profile of each half link roughly symmetric with respect to the midway optical phase conjugator.

Spraying various liquids (primarily aqueous solutions of various substances) is widely used in various technological processes. For most of them, high dispersibility and narrow droplet size distribution are essential. This facilitates ultrasonic spray technique. However, the higher the dispersity of droplets produced by ultrasonic spray, the lower the spray productivity. To solve this problem, we proposed a method of multistage spraying, consisting in generation of a large number of particles of large initial size (to ensure high productivity) and their subsequent destruction by propagation in a periodic ultrasonic field (to ensure small droplet sizes at high productivity). To experimentally determine the capabilities of this technique, a tubular emitter in the shape of a cylinder of stepped-variable cross-section was designed. Configuration of the ultrasonic field inside the emitter (22.2 kHz; 182 dB) implements three-stage spraying (the number of sputtering stages corresponds to the number of anti-nodes along the emitter axis). The effectiveness of proposed and developed technique suitable for generation of droplets sized less than 40 µm with performance exceeding the known ultrasonic spray techniques at least 10 times has been confirmed in the course of conducted research.

In the land use planning framework in the neighbourhood of industrial facilities, the current approach to predicting the consequences of massive toxic gas releases is generally based on Gaussian or integral models. For many years, CFD models have been more and more used in this context, in accordance with the development of High-Performance Computing (HPC). The present paper focuses on harmonizing input data for Atmospheric Transport and Dispersion (AT&D) modelling between the widely used approaches. First, a synthesis of the practice’s harmonization for atmospheric dispersion modelling within the framework of risk assessment is presented. Then, these practices are applied to a large-scale INERIS ammonia experimental release. For illustration purposes, the impact of the proposed harmonization will be evaluated using different approaches: the SLAB model, the FDS model and the Code_Saturne model. The two main focuses of this paper are the adaptation of the source term dealing with a massive release and the wind flow modelling performance using an experimental signal for CFD models inflow. Finally, comparisons between the modelling and experimental results enable checking the consistency of these approaches and reinforce the importance of the input data harmonization for each AT&D modelling approach.

Polyaniline or PANI is a conductive polymer (CPs) with flexibility in turning into conducting properties. The drawback is mainly in terms of limited mechanical properties improvement which attracted the interest in fabrication of PANI with other polymeric materials. PANI-PVL composites film was synthesized and fabricated in this work with chronological steps according to the objectives aligned in two different phases. The first phase determines the optimum parameters to synthesize nanosized PANI. The ideal initial molar ratio, r was 1, stirring speed of 600 rpm, purified by filtration, synthesis temperature of 25 oC, washed by dopant acid, acetone and distilled water. The usage of non-ionic surfactant, Triton X-100 (TX100) with 0.1 % concentration favours the formation of smaller particle size of PANI and good dispersibility compared to the usage of anionic sodium dodecyl sulphate (SDS). The synthesis of PANI in nanosized dimension has the potential to be applied for antimicrobial applications such as gloves and antimicrobial coating of frequent contact points in the near future.

Background: Previous studies have associated slowed ventricular conduction in the arrhythmogenesis mediated by the gap junction and sodium channel inhibitor heptanol in mouse hearts but did not study the propagation patterns that might contribute to the arrhythmic substrate. This study used a multi-electrode array mapping technique, to further investigate different conduction abnormalities in Langendorff-perfused mouse hearts exposed to 0.1 or 2 mM heptanol. Methods: Multi-electrode array recordings were made from the left ventricular epicardium in spontaneously beating hearts, during right ventricular regular 8 Hz pacing or S1S2 pacing. Results: In spontaneously beating hearts, heptanol at 0.1 and 2 mM significantly reduced the heart rate from 314±25 to 189±24 and 157±7 bpm, respectively (ANOVA, P<0.05 and P<0.001). During regular 8 Hz pacing, Mean LATs were increased by 0.1 and 2 mM heptanol from 7.1±2.2 ms to 19.9±5.0 ms (P<0.05) and 18.4±5.7 ms (P<0.05). The standard deviation of mean LATs was increased from 2.5±0.8 ms to 10.3±4.0 ms and 8.0±2.5 ms (P< 0.05), and the median of phase differences was significantly increased from 1.7±1.1 ms to 13.9±7.8 ms and 12.1±5.0 ms by 0.1 and 2 mM heptanol (P<0.05). P5 took a value of 0.2±0.1 ms and was not significantly altered by heptanol at 0.1 or 2 mM (1.1±0.9 ms and 0.9±0.5 ms, P>0.05). P50 was increased from 7.3±2.7 ms to 24.0±12.0 ms by 0.1 mM heptanol and then to 22.5±7.5 ms by 2 mM heptanol (P< 0.05). P95 was increased from 1.7±1.1 ms to 13.9±7.8 ms by 0.1 mM heptanol and to 12.1±5.0 ms by 2 mM heptanol (P<0.05). These changes led to increases in the absolute inhomogeneity in conduction (P5-95) from 7.1±2.6 ms to 31.4±11.3 ms, 2 mM: 21.6±7.2 ms, respectively (P<0.05). The inhomogeneity index (P5-95/P50) was significantly reduced from 3.7±1.2 to 3.1±0.8 by 0.1 mM and then to 3.3±0.9 by 2 mM heptanol (P<0.05). Conclusion: Increased activation latencies, reduced CVs and increased dispersion index of conduction were associated with both spontaneous and induced ventricular arrhythmias.

Keywords: liquid alloys, microstratification, dispersed particles, spontaneous dispersion, criteria for true (entropic) spontaneous dispersion, mechanisms of quasi-spontaneous dispersion, methods and results for assessing size of dispersed particles.

In this study, Al-Al4C3 compounds were manufactured by mechanical milling followed by heat treatment. To analyze the microstructural evolution, the composites were sintered at 550°C during different sintering times of 2, 4 and 6 hours. The mechanical results suggest that dislocation density and crystallite size primary contribute to hardening before the sintering process, with a minimal contribution from particle dispersion in this condition. The compound exhibited a significant 75% increase in hardness after 2 hours of sintering, primarily attributed to the nucleation and growth of Al4C3 nanorods. The HRTEM analysis, combined with ge-ometric phase analysis (GPA) at and near the Al-Al4C3 interface of the nanorods, revealed strain field distributions primarily associated with partial screw dislocations and the presence of closely spaced dislocation dipoles. These findings are consistent with the microstructural parameters determined from X-ray diffraction pattern analysis using the convolutional multi-ple whole profile (CMWP) method. This analysis showed that the predominant dislocation character is primarily of the screw type, with the dislocation dipoles being closely correlated. Based on these results, it is suggested that samples with a lower weight percentage of rein-forcement and longer sintering times may experience reduced brittleness in Al/Al4C3 compo-sites. Strengthening contributions were calculated using the Langford–Cohen and Taylor equations.

Plasmonics is the study of resonant oscillations of free electrons in metals caused by incident electromagnetic radiation. Surface plasmons can focus and steer light on the subwavelength scale. Apart from metals, plasmonic phenomena can be observed in soft matter systems such as electrolytes where resonant charge oscillations can be induced for ions in solution. Due to their larger mass, they are plasmon-active in a lower frequency regime and on a larger wavelength scale. Spatial confinement allows increasingly strong charge interactions and gives rise to nonlocality or spatial dispersion effects. These effects manifest as additional longitudinal propagation modes and are known to cause plasmonic broadening and resonance shifts in metal nanostructures. We derive and discuss the nonlocal optical response of ionic plasmons using a hydrodynamic, two-fluid model in a planar homogeneous three-layer system with electrolyte-dielectric interfaces. Studying such systems enables us to identify and understand plasmonic phenomena in biological and chemical systems.

This manuscript investigates the dispersion of cetyltrimethylammonium bromide (CTAB) treated cellulose nanocrystals (CNCs) in polypropylene (PP) by melt mixing. FTIR spectra of CTAB-modified CNCs and unmodified CNCs in a PP matrix were used to evaluate the surface treatments. The surface energies and morphologies of CTAB surface modified CNCs in polypropylene (PP) were used to interpret the effects of nanoparticle dispersion on the crystallization and rheological and mechanical properties of the PP matrix.

Acoustic metasurface are artificial structures which could manipulate the wavefront in sub-wavelength dimensions and the previous proposed acoustic metasurface were mostly realized with single materials. An acoustic metasurface with composite structure is proposed for underwater acoustic stealth considering both wavefront manipulation and sound absorption. The unit cells of the metasurface are composed by metallic supporting lattice, interconnecting polymer materials and mass balancing columns. With the gradual modulations of equivalent physical properties along the horizontal direction of metasurface, the incident acoustic wave is reflected to other directions. Meanwhile, the polymer material inside the unit cells would dissipate the acoustic wave energy due to inherent damping properties. With the simultaneous modulations of reflected wave direction and scattering acoustic amplitude, significant improvement of underwater stealth effect is achieved. Compared with single-phase metasurface, the Far-Field Sound Pressure Level (FFSPL) of the multiphase metasurface decreased by 4.82 dB within the frequency range of 3kHz~30kHz. Under a hydrostatic pressure of 5MPa, the linearized mean stress for multiphase metasurface is only 1/3 of that of single-phase metasurface due to much thicker struts and much more uniform stress distribution. The proposed composite structure possesses potential applications due to acceptable thickness (80mm) and low equivalent density (1100 kg/m3).

Ultrashort pulses are severely distorted even by low dispersive media. While the mathematical analysis of dispersion is well known, the technical literature focuses on pulses, which keep their shape: Gaussian and Airy pulses. However, the cases where the shape of the pulse is unaffected by dispersion is the exception rather than the norm. It is the object of this chapter to present a variety of pulses profiles, which have analytical expressions but can simulate real-physical pulses with greater accuracy. In particular, the dynamics of smooth rectangular pulses, physical Nyquist-Sinc pulses, and slowly rising but sharply decaying ones (and vice-versa) are presented. Besides the usage of this chapter as a handbook of analytical expressions for pulses' propagations in a dispersive medium, there are several new findings. The main ones are: Analytical expressions for the propagation of chirped rectangular pulses, which converge to extremely short pulses; analytical approximation for the propagation of Super-Gaussian pulses; the propagation of Nyquist Sinc Pulse with smooth spectral boundaries and an analytical expression for a physical realization of an attenuation compensating Airy pulse.

Alumina dispersion-strengthened copper, Glidcop, is used widely in high-heat-load ultra-high-vacuum components for synchrotron light sources (absorbers), accelerator components (beam intercepting devices) and in nuclear power plants. Glidcop has similar thermal and electrical properties to OFE (oxygen free electrical) copper, but has superior mechanical properties, thus making it a feasible structural material; its yield and ultimate strength are equivalent to those of mild-carbon steel. The purpose of this work has been to develop a brazing technique to join Glidcop to Mo, using a commercial Cu-based alloy. The effects of the excessive diffusion of the braze along the grain boundaries on the interfacial chemistry and joint microstructure, as well as on the mechanical performance of the brazed joints, has been investigated. In order to prevent the diffusion of the braze into the Glidcop alloy, a copper barrier layer has been deposited on Glidcop by means of RF-sputtering.

It is familiar that the Casimir self-energy of a homogeneous dielectric ball is divergent, although a finite self-energy can be extracted through second order in the deviation of the permittivity from the vacuum value. The exception occurs when the speed of light inside the spherical boundary is the same as that outside, so the self-energy of a perfectly conducting spherical shell is finite, as is the energy of a dielectric-diamagnetic sphere with $\varepsilon\mu=1$, a so-called isorefractive or diaphanous ball. Here we re-examine that example, and attempt to extend it to an electromagnetic $\delta$-function sphere, where the electric and magnetic couplings are equal and opposite. Unfortunately, although the energy expression is superficially ultraviolet finite, additional divergences appear that render it difficult to extract a meaningful result in general, but some limited results are presented.

In this paper, we introduce a comprehensive solution aimed at enhancing the understanding of three-dimensional atmospheric pollutant dispersion. This innovative solution develops a generalized model that extends previous research and is applicable to all parameterization schemes of the equation, including wind speed profiles and turbulent diffusion coefficients, while incorporating the dry deposition criterion. Our methodology involves subdividing the atmospheric boundary layer into distinct sublayers, which facilitates a detailed examination of pollutant dispersion dynamics. Extensive validation with data from the Hanford experiment has demonstrated the accuracy of this solution in simulating pollutant concentrations. The results exhibit a strong correlation between projected and observed concentrations, underscoring the statistical reliability of our approach. This validation situates the statistical indices of our solution within an acceptable range, confirming its accuracy in predicting atmospheric pollutant dispersion. These findings thus establish our solution as a valid and effective method for studying complex environmental phenomena.

Motivated by important applications to the analysis of complex noise-induced phenomena, a problem of the constructive description of randomly forced equilibria for nonlinear systems with multiplicative noise is considered. Using apparatus of the first approximation systems, we construct an approximation of mean square deviations that explicitly takes into account the presence of multiplicative noise. This approximation is compared with the widely used approximation based on the stochastic sensitivity technique. The general mathematical results are illustrated with the example of the van der Pol oscillator with hard excitement.

Accurate calculation of non-covalent interaction energies in nucleotides is crucial for understanding the driving forces governing nucleic acid structures and functions, as well as developing advanced molecular mechanics forcefields or machine learning potentials tailored to nucleic acids. Here, we dissect the nucleotides’ structure into three main constituents: nucleobases (A, G, C, T, and U), sugar moieties (ribose and deoxyribose), and phosphate group. The interactions among these fragments and between fragment and water were analyzed. Different quantum mechanical methods were compared for their accuracy in captuing the interaction energy. The non-covalent interaction energy was decomposed into electrostatics, exchange-repulsion, dispersion, and induction using two ab-initio methods: Symmetry-Adapted Perturbation Theory (SAPT) and Absolutely Localized Molecular Orbitals (ALMO). These caculations provide the benchmark for different QM methods while providing valuable understanding of the roles of various interamolecular forces in hydrogen bonding and aromatic stacking.

The fractional advection-dispersion equation FADE plays an important role, especially in explaining the process of solute-transport in natural porous media with different degrees of heterogeneity. However, studies of the flow and transport of contaminants in the underground environment are based on the knowledge of many functional parameters of the subsoil. The delay factor caused by nonlinear absorption is one of these parameters inheriting significant ambiguities in its estimation in heterogeneous media. In the study, a fractional advection-dispersion FADE model was developed by the implicit Euler method, based on a Grunwald and Caputo-Liousville approximation to explicitly evaluate and simulate the transport mechanism of contaminants in media with unsaturated porous materials subjected to a nonlinear sorption model. Better solute mass retention was observed for fractional advection-dispersion FADE model. Moreover, the absorption parameter of the retardation coefficient has a better impact on the motion of the solute in a saturated porous medium. In other words, it has a significant effect on the dispersion of pollutants in aquifers. This study highlights the need to characterize the aquifer to predict solute transport in porous media.

This study explores the near-surface dispersion mechanisms of contaminants in coastal waters, leveraging a comprehensive method that includes using dye and drifters as tracers, coupled with diverse observational platforms like drones, satellites, in-situ sampling, and HF radar. The aim is to deepen our understanding of surface currents' impact on contaminant dispersion, thereby improving predictive models for environmental incident management, including pollutant releases. Rhodamine WT dye, chosen for its significant fluorescent properties and detectability, along with drifter data, allowed us to investigate the dynamics of near-surface physical phenomena such as the Ekman current, Stokes drift, and wind-driven currents. Our research emphasizes the importance of integrating scalar tracers and Lagrangian markers in experimental designs, revealing differential dispersion behaviors due to near-surface vertical shear caused by the Ekman current and Stokes drift. The elongation direction of the dye patch aligns with the Ekman current direction during slow current conditions. Analytical calculations of vertical shear, based on the Ekman current and Stokes drift, closely matched those derived from tracer observations. Over a 7-hour experiment, the vertical diffusivity of near-surface water was observed at 2×10-4 m2/s, and the horizontal eddy diffusivity of the dye patch and drifters reached the order of 1 m2/s and at a 1000m length scale. Particle tracking models demonstrate that while HF radar currents can effectively predict the trajectories of tracers near the surface, incorporating near-surface currents, including Ekman current, Stokes drift, and windage, is essential for a more accurate prediction of the fate of surface floats.

Gold nanohole arrays are periodic metastructures gathering huge interest for biosensing applica-tions. The grating-like structure defines their plasmonic mode features and their angular disper-sion can be used to highlight efficiently their interaction with the fluorescence emission of a properly tuned fluorophore. Resorting to a properly tuned/engineered/optimised plasmonic na-nohole array and a commercial organic dye, we performed an accurate resolved angle-resolved optical characterization. The plasmonic fingerprints was consequently identified as a modification of the dye photoluminescence signal in terms of both spectral redistribution and enhancement. Interestingly, by analyzing the results, an advantageous measurement configuration can be iden-tified to better engineer a suitable platform for efficiency maximization in plasmon-enhanced flu-orescence-based applications. Therefore, the coupling mechanism with the plasmonic modes, and nanostructure properties can be carefully co-optimized.

A new method is proposed for performance assessment of lubricating compositions based on industrial lubricants that contain nano-additives of different chemical composition for higher wear resistance of heavy-loaded steel friction pairs. The method is based on the joint analysis of the experimental data on the wear kinetics, change of the relative hardness, and damage in the surface layers of the metal of friction pairs. The level of structural damage to the materials in the contact zone is determined by using the statistical parameters of dispersion of the hardness values. The paper investigates the known experimental results of assessment of the level of damage to structural materials of various grades under the conditions of long-term, cyclic, static loading, and lubricated friction. It is demonstrated that the structural changes occurring in the materials during loading correlate to the changes in the statistical dispersion characteristics of hardness measurement results. Experimental substantiation of the method is carried out for steel friction pairs using lubricating compositions based on industrial oil Greaseline Lithium BIO Rail 000 by AIMOL and nano-additives of copper of M2 grade, magnesium alloy of MA2 grade, aluminum alloy of Al-Mg system, graphite of medium carbon steel grades, i.e. rail and industrial. Under system of indicators presented in the paper, the highest efficiency in terms of increase in the wear resistance of steel friction pairs is demonstrated by the lubricating composition based on industrial lubricant with the additive of nano-powder made of rail steel, as it provided the optimum value of friction coefficient, minimum damage and wear of friction surface.

Derelict asbestos mine sites in South Africa pose a considerable risk to human, environmental and socio-economic health. Comprehensive mineralogical and geochemical datasets for the existing hazardous geological materials still exposed in Southern African derelict asbestos mines remain largely non-existent, as very little published and up-to-date literature is available. In this study three representative types of asbestos mineral fibres from derelict asbestos mines in Southern Africa, namely chrysotile from Havelock mine, amosite from Penge mine and crocidolite from Prieska mine are characterized mineralogically and geochemically to critically evaluate real-life hazards in rural and asbestos-fibre contaminated regions. The samples were examined using polarising light microscopy, X-ray fluorescence (major and trace elemental analysis), X-ray diffraction (including Rietveld refinement), specific surface area analyses and bio-durability tests. Data are discussed in view of their potential toxicities on both human health and the environment in the context of developing countries. Finally, information on the mineralogical and geochemical status of asbestos mine waste and its importance as baseline data for rehabilitation considerations is also evaluated.

The statistical properties of a good estimator include robustness, unbiasedness, efficiency, and consistency. However, the commonly used estimators of dispersion have lack or are weak in one or more of these properties. In this paper, I proposed statistical mirroring as a good alternative estimator of dispersion around defined location estimates or points. In the main part of the paper, attention is restricted to Gaussian distribution and only estimators of dispersion around the mean that functionalize with all the observations of a dataset were considered at this time. The different estimators were compared with the proposed estimators in terms of alternativeness, scale and sample size robustness, outlier biasedness, and efficiency. Monte Carlo simulation was used to generate artificial datasets for application. The proposed estimators (of statistical meanic mirroring) turn out to be suitable alternative estimators of dispersion that is less biased (more resistant) to contaminations, robust to scale and sample size, and more efficient to a random distribution of variable than the standard deviation, variance, and coefficient of variation. However, statistical meanic mirroring is not suitable with a mean (of a normal distribution) close to zero, and on a scale below ratio level.

Integral atmospheric dispersion models are used widely for flammable hazard and its risk analysis. There is a widespread belief that flammable distances from these models are conservative when flammable ranges are calculated using the 0.5 lower flammability limits (LFL) concentration threshold. This is erroneous. This paper traces through the development of these models and the research that led to the Birch Guidance. It shows that the 0.5 LFL is a necessary factor to transform the results of dispersion models designed for environmental assessment to applications to flammable hazard assessment in quiescent conditions. Current applications do not take account of turbulence due to wind, large and small obstructions, etc. A set of simple guidance is given in the paper to manage flammable hazards based on results from atmospheric dispersion models, including topics for future research.

We show that an experimentally plausible system consisting of a modulated wire medium hosted in a metal cavity can preserve the longitudinal field profile shaping predicted by Boyd et al. (2018) on the basis of a perfectly periodic wire-only structure. These new frequency domain numerical results are a significant step towards justifying the construction of an experimental apparatus to test the field profile shaping in practise.

We present an exact expression for the upscaled dynamic dispersion coefficient (D) for one-dimensional transport by Hagen-Poiseuille flow which is the basis for modeling transport in porous media idealized as capillary tubes. The theoretical model is validated by comparing the breakthrough curves (BTCs) from a 1D advection-dispersion model with dynamic D to that from direct numerical solutions utilizing a 2D advection-diffusion model. Both Taylor dispersion theory and our new theory are good predictors of D at lower Peclet Number (Pe) regime, but gradually fail to capture most parts of BTCs as Pe increases. However, our model generally predicts the mixing and spreading of solutes better than Taylor’s theory since it covers all transport regimes from molecular diffusion, through anomalous transport, and to Taylor dispersion. The model accurately predicts D based on the early part of BTCs even at relatively high Pe regime (~62) where the Taylor’s theory fails. Furthermore, the model allows for calculation of the time scale that separates Fickian from non-Fickian transport. Therefore, our model can readily be used to calculate dispersion through short tubes of arbitrary radii such as the pore throats in a pore network model.

No doubt pollution is a global problem which must be holistically tackled. In doing this, adequate knowledge of the sources of pollution is important, therefore the aim of this paper is to review source apportionment with reference to top-down and bottom-up methods. In this paper, dispersion modeling, emissions inventory, and sampling methods were discussed. Also, analytical methods involved in top-down source apportionment were mentioned. The two techniques are needed to evaluate pollutants and their sources. Based on these two approaches, pollution control strategy would be developed and decisions can be made in deciding the right approach to solve or reduce the pollution problems.

This paper discusses approaches to the numerical integration of the coupled nonlinear Schrödinger equations system in case of few-mode wave propagation. The wave propagation assumes the propagation of up to nine modes of light in an optical fiber. In this case, the light propagation is described by the non-linear coupled Schrödinger equation system, where propagation of each mode is described by own Schrödinger equation with other modes interactions. In this case, the non-linear coupled Schrödinger equation system solving becomes increasingly complex, because each mode affects the propagation of other modes. The suggested solution is based on the direct numerical integration approach, which is based on a finite-difference integration scheme. The well-known explicit finite-difference integration scheme approach fails, due to the non-stability of the computing scheme. Due to this fact, the combined explicit/implicit finite-difference integration scheme, based on the implicit Crank–Nicolson finite-difference scheme, is used. It allows ensuring the stability of the computing scheme. Moreover, this approach allows separating the whole equation system on the independent equation system for each wave mode at each integration step. Additionally, the algorithm of numerical solution refining at each step and the integration method with automatic integration step selection are used. The suggested approach has performance gains (or resolutions) up to three or more orders of magnitude in comparison with the split-step Fourier method due to the fact that there is no need to produce direct and inverse Fourier transforms at each integration step. The main advantage of the proposed method is the ability to calculate the propagation of an arbitrary number of modes in the fiber.

Reliable and precise damage localization in mechanical structures is of high importance in the context of structural health monitoring (SHM). The acoustic emission (AE) method has already shown its excellent suitability for damage localization. However, low signal-to-noise ratios (SNRs) are often prevalent in SHM, thus an increase in localization accuracy and robustness is still in demand. The present study faces this task through the integration of various model knowledge for AE source localization. The basis of the presented algorithm is the consideration of the dispersive behavior of elastic waves in thin-walled structures. The continuous wavelet transform (CWT) is used to obtain time-frequency representations of the signals, where frequency-dependent values for time-of-arrival (TOA) are extracted. Furthermore, the algorithm incorporates the knowledge that all sensors receive signals with the same time and location of origin, as well as the slightly different sensitivity of the theoretically equal sensors. The final localization results are achieved by a two-parameter grid search optimization. The algorithm is experimentally tested on a large aluminum plate with four piezoelectric wafer active sensors (PWASs) arranged in an array of 100 mm × 100 mm. The mean localization error of pencil lead breaks at ten different positions within the sensor array is used as an accuracy measure. It is shown that as more of the described model knowledge is incorporated into the localization, the accuracy increases. With the final algorithm, the mean localization error is more than halved compared to AE localization based on classical TOA estimation. Although the experiment described is conducted under laboratory conditions, the remarkable increase in accuracy suggests that AE source localization may be successful even at low SNR as typical for operational conditions.

Nowadays, rotor-stator mixers are widely used in the chemical process industry to carry out the dispersion and de-agglomeration processes for manufacturing the homogenous electrode slurries. Development of the process simulation models for the turbulent mixing of these slurries helps to optimize the mixing parameters such as rotational speed and dispersion time. In this work, computational fluid dynamics (CFD) approach through ANSYS Fluent are explored to determine and analyze the flow patterns, velocity fields and viscosity distribution during the dispersion of anode slurries. It utilizes a non-homogeneous Eulerian multiphase approach and the typical k-ε model to create turbulence fields and compute the mixing rate. This work significantly improves our understanding of the relationship between rotor speed, dispersion time, viscosity distribution, and mixer geometry in rotor-stator mixers.

Experimental studies on the development of processes of obtaining ultradispersed metal-ceramic materials and coatings Mo-ZrO₂, Mo-Al₂O₃, W-ZrO₂, W-Al₂O₃ CVD by deposition from the gas phase in CO₂ process using low-temperature nonequilibrium plasma were carried out.The structure, microhardness, phase composition, and high-temperature annealing behavior of the materials were studied. It is shown that the choice of parameters of the deposition process and temperature annealing can be controlled by the distribution function of ultradispersed particles in the material and their sizes.High-temperature X-ray studies of "molecular" two-phase alloys Mo- Al₂O₃ and Mo- ZrO₂show that, depending on the elastic and thermal properties of the matrix materials and dispersed particles, the molybdenum matrix can be in an all-round tensed or all-round compressed state.In the study of the electro-physical characteristics of the two-phase disperse-strengthened alloys Mo- ZrO₂, Mo- Al₂O₃, W- ZrO₂, W- Al₂O₃ it has been established that in the region of temperatures 1023...1273K anomalous changes of specific electrical resistance and instability of thermal eddy in magnitude are observed apparently connected with the presence of internal stresses in material caused by ultradisperse particles.Theoretical aspects of the problem of increasing the carriers density in nanocomposite materials are reviewedTheoretical analysis of the effect of the ensemble of microparticles on the change of electron density in ultradisperse metal-ceramic materials is carried out. It is shown that the average values of the electron density in the matrix with the introduction of 1% of particles with a radius of 50 A increase by more than two orders of magnitude.The possibilities of creating ultradisperse compositions using radiation-plasma methods are considered.

The present study was designed to develop a self-micellizing solid dispersion (SMSD) containing Thymoquinone (TQM), a phytonutrient obtained from Nigella sativa seeds, aiming to improve its biopharmaceutical and nephroprotective functions. The apparent solubility of TQM in polymer solutions was used to choose an appropriate amphiphilic polymer that could be used to make an SMSD system. Based on the apparent solubility, Soluplus® was chosen as an appropriate carrier, and mixing with TQM, SMSD-TQM with different loadings of TQM (5–15%) was made by solvent evaporation and freeze-drying techniques, respectively, and the formulations were optimized. The optimized SMSD-TQM was evaluated in terms of particle size distribution, morphology, release characteristics, pharmacokinetic behavior, and nephroprotective effects in a rat model of acute kidney injury. SMSD-TQM significantly improved the dissolution characteristics (97.8%) of TQM in water within 60 min. Oral administration of SMSD-TQM in rats exhibited a 4.9-fold higher systemic exposure than crystalline TQM. In a cisplatin-induced (6 mg/kg, i.p.) acute kidney-damaged rat model, oral SMSD-TQM (10 mg/kg) improved the nephroprotective effects of TQM based on the results of kidney biomarkers and histological abnormalities. These findings suggest that SMSD-TQM might be efficacious in enhancing the nephroprotective effect of TQM by overcoming biopharmaceutical limitations.

Nigella sativa's thymoquinone (TQM), a water-insoluble phytonutrient exhibits nephroprotective effects. This study intends to develop a self-micellizing solid dispersion (SMSD) of TQM for better biopharmaceutical and nephroprotective performance. Soluplus®-based SMSD of TQM was created and tested for physicochemical properties, solubility, and pharmacokinetics in rats. Plasma creatinine, blood urea nitrogen (BUN), nephrotoxic indicators, and oxidative stress biomarkers were also tested. During SMSD preparation, TQM was found amorphous, boosting solubility. Minimal band changes between TQM and Soluplus® indicate insignificant drug-carrier interactions. SMSD-TQM generated fine micelles in water, improving TQM's solubility by 97.8% in 60 min. SMSD-TQM was 4.9 times more bioavailable orally in rats than crystalline TQM. In a rat model of acute renal damage by cisplatin (6 mg/kg, i.p.), SMSD-TQM (10 mg-TQM/kg, p.o.) reduced blood creatinine and BUN by 56% and 63.2%, respectively. These findings imply that SMSD-TQM may be a potent dosage option for enhancing TQM's nutrient value.

Road vehicles are a large contributor to Nitrogen Oxides (NOx) pollution. The routine road-side monitoring stations, however, may underrepresent the severity of personal exposure in urban areas, because long-term average readings cannot capture the effects of momentary, high peaks of air pollution. While numerical modelling tools historically have been used to propose an improved distribution of monitoring stations, ultra-high resolution Computational Fluid Dynamics models can further assist the relevant stakeholders in understanding the important details of pollutant dispersion and exposure at local level. This study deploys a 10 cm-resolution CFD model to evaluate actual high peaks of personal exposure to NOx from traffic, by tracking the gases emitted from the tailpipe of moving vehicles being dispersed towards the roadside. The investigation shows that a set of four Euro 5-rated diesel vehicles travelling at constant speed may generate momentary road-side concentrations of NOx as high as 1.25 mg/m3, with 25% expected increase for doubling the number of vehicles and approximately 50% reduction when considering Euro 6-rated vehicles. The paper demonstrates how the numerical tool can be used to identify the impact of measures to reduce personal exposure, such as protective urban furniture, as traffic patterns and environmental conditions change.

The antioxidant potential (capacity and activity) of aqueous fullerene dispersions (AFD) of non-functionalized C₆₀, C₇₀, and Gd@C₈₂ endofullerene (in micromolar concentration range) was estimated based on chemiluminescence measurements of the model of luminol and generation of organic radicals by 2,2’-azobis(2-amidinopropane) dihydrochloride (ABAP). The antioxidant capacity was estimated by the TRAP method, from the concentration of half-suppression, and from the suppression area in the initial period. All three approaches agree and show that the antioxidant capacity of AFDs increased in the row Gd@C₈₂ < C₇₀ < C₆₀. Mathematical modeling of the long-term kinetics data was used for antioxidant activity estimation. The effect of C₆₀ and C₇₀ is found to be quenching of the excited product of luminol with ABAP-generated radical and not an actual antioxidant effect; quenching constants differ insignificantly. Apart from quenching with a similar constant, the AFD of Gd@C₈₂ exhibits actual antioxidant action. The antioxidant activity in Gd@C₈₂ is 300-fold higher than quenching constants.

The discovery of a growing number of exoplanets and even extrasolar systems supports the scientific consensus that it is possible to find other signs of life in the universe. The present work proposes for the first time, an explicit mechanism inspired by the dynamics of biological dispersion, widely used in ecology and epidemiology, to study the dispersion of biogenic units, interpreted as complex organic molecules, between rocky or water exoplanets (habitats) located inside star clusters. The results of the dynamic simulation suggest that for clusters with populations lower than 4 M+/ly³ it is not possible to obtain biogenic worlds after 5 Gyr. Above this population size, biogenic dispersion seems to follow a power law, the larger the density of worlds lesser will be the impact rate (β ) value to obtain at least one viable biogenic Carrier habitat after 5 Gyr. Finally, when we investigate scenarios by varying β, a well-defined set of density intervals can be defined in accordance to its characteristic β value, suggesting that biogenic dispersion has a behavior of “minimal infective dose” of “minimal biogenic effective” events by interval i.e. once this dose has been achieved, doesn’t matter if additional biogenic impact events occur on the habitat.

The geometry of mesoscopic inhomogeneities plays an important role in determining the macroscopic propagation behaviors of elastic waves in a heterogeneous medium. Non-equiaxed inhomogeneities can lead to anisotropic wave velocity and attenuation. Developing an accurate scattering theory to describe the quantitative relation between the microstructure features and wave propagation parameters is of fundamental importance for seismology and ultrasonic nondestructive characterization. This work presents a multiple scattering theory for strongly scattering elastic media with general tri-axial heterogeneities. A closed analytical expression of the shape-dependent singularity of the anisotropic Green’s tensor for the homogeneous reference medium is derived by introducing a proper non-orthogonal ellipsoidal coordinate. Renormalized Dyson’s equation for the coherent wave field is then derived with the help of Feynman’s diagram technique and the first-order-smoothing approximation. The exact dispersion curves and the inverse Q-factors of coherent waves in several representative medium models for the heterogeneous lithosphere are calculated numerically. Numerical results for small-scale heterogeneities with the aspect ratio varying from 1 to 7 show satisfactory agreement with those obtained from real earthquakes. The results for velocity dispersion give rise to a novel explanation to the formation mechanism of different seismic phases. The new model has potential applications in seismology and ultrasonic microstructure characterization.

The application of naturally ventilated pig buildings (NVPBs) with outdoor exercise yards is on the rise mainly due to animal welfare considerations, while the issue of emissions from the buildings to the surrounding environment is important. Since air pollutants are mainly transported by airflow, the knowledge on the airflow characteristics downwind the building is required. The objective of this research was to investigate airflow properties downwind of a NVPB with a roofed outdoor exercise yard for roof slopes of 5°, 15°, and 25°. Air velocities downwind a 1:50 scaled NVPB model were measured using a Laser Doppler Anemometer in a large boundary layer wind tunnel. A region with reduced mean air velocities was found along the downwind side of the building with a distance up to 0.5 m (i.e. 3.8 times building height), in which the emission concentration might be high. It was found that a smaller roof slope (i.e. 5° slope) resulted in a higher and shorter wake zone and thus a shorter air pollutant dispersion distance. It was concluded that a smaller roof slope could contribute to the dilution of air pollutants and a lower air pollutant concentration near the ground.

Longitudinal dispersion coefficient (LDC) plays an essential role in modeling the transport of pollution and sediment in the natural rivers. As a result of transportation processes, the concentration of pollution changes along the river. Different studies have been conducted to provide simple equations for estimating LDC. In this study, Support Vector Regression (SVR), Gaussian Process Regression (GPR), M5P and Random Forest (RF) examined to predict the LDC in the natural streams. The hydraulic and geometric features of different rivers gathered for developing the mentioned models for LDC estimation and various statistical criteria were utilized to scrutinize of the models. Furthermore, the Taylor chart was used to evaluate the models and achieved results showed that among machine learning models, M5P displayed the superior performance with CC of 0.823, SI of 0.812, NS of 0.577 and WI of 0.879. As well, S-D model with CC of 0.795 SI of 0.827, NS of 0.558 and WI of 0.890 had more precise results than other empirical models. The results indicates that the developed M5P model with simple formulations was superior to other machine learning models and empirical models and therefore, it can be used as a proper tool for estimating LDC in natural rivers.

Crystallization behavior of hexadecane (C₁₆H₃₄), octadecane (C₁₈H₃₈), eicosane (C₂₀H₄₂), and docosane (C₂₂H₄₆) dispersions of similar mean droplet diameter (x_50.2 ≈ 15 µm) was investigated in quiescent systems and compared to crystallization under mechanical stress. In quiescent systems, the required supercooling decreased with increasing chain length of the alkanes to initiate crystallization. Crystallization of alkane dispersions under mechanical stress resulted in similar onset crystallization supercooling, as during quiescent crystallization. Increase of mechanical stress did not affect the onset crystallization supercooling within alkane dispersions.

For measuring time, distances and movements, including determining the location of ground objects using a global navigation satellite system using the triangulation method, high-precision generators of extremely accurately generated reference frequencies, as reference measures of frequency and time intervals, are extremely relevant. Along with those already approved as frequency and time standards, exemplary stable frequency signal generators are constantly being created, improved and researched, that is, prototypes of future frequency and time standards based on new principles. Model generators are also being created on known principles with additional measures to increase their accuracy. The most important stage in the creation of such standards and their prototypes is the study of the stability and accuracy characteristics of the resulting model generators. Traditionally, indicators such as the two-sample Allan variance are used for this, and even more often the square root of this value, called the Allan function, is used. Many publications report results in which the dependence of this function on the averaging time is given on a double logarithmic scale. A decrease in this value with increasing averaging time looks natural and is beyond doubt, however, the right branch of this graph very often begins to bend upward, which indicates that with increasing averaging time the Allan function increases. This fact cannot satisfy future users of these exemplary generators, since such an increase indicates that the frequency value they generate should not be trusted, because it turns out that over a long period of time the generated frequency can deviate from the required value very far, and the longer this time , the more this function can deviate. The situation is aggravated by the fact that the Allan function does not include offset, that is, such an important characteristic as frequency reproducibility, when in fact this characteristic should also be taken into account. This article offers a new vision and interpretation of the metrological characteristics of the accuracy, stability and reproducibility of the generated frequency of a model generator.

Real-time simulation of toxic gas dispersion is critical for emergency management in high-sulphur gas fields. The CALPUFF (California Puff model) gas dispersion model, a Lagrangian Gaussian Puff model, is often used in mountainous environments due to its ability to handle complex terrain and weather conditions. Verifying the accuracy of toxic gas dispersion simulations under mountainous conditions is vital for emergency response and rescue. In this article, CALPUFF and Computational Fluid Dynamics (CFD) gas dispersion modeling are compared, studying emissions from a hypothetical pipeline breakout accident in a mountainous area, focusing on range of Semi-Lethal Concentration (LC$_{50}$), Immediate Danger to Life and Health Concentration(IDLH). Thirteen groups of simulation conditions are set up for the experiment, including static wind and winds from the east(E), south(S), west(W), and north(N) at speeds of 1, 2, and 3$m/s$. Comparative experiments between CALPUFF and CFD models show consistent results, confirming the feasibility of CALPUFF for near-field moutainous applications. The overall dispersion range deviation between two methods under calm or light wind of N, E and W is about 300$m$. However,the simulation results of the CALPUFF model and the CFD model show significant differences in S wind. In CALPUFF simulation that the toxic gases are channeled by the valleys, while in the CFD model the toxic gases climb over the mountain top and continue to spread and extend towards the northern valley. The evaluation of CALPUFF’s suitability for applications in near-field mountainous environments indicates its potential use for high-sulfur gas fields and gas dispersion simulations in emergency scenarios.

Integrating nanomaterials like carbon nanotubes (CNTs) and iron oxide (Fe₃O₄) into epoxy composites has significant interest due to their potential to enhance mechanical properties. This study evaluates the impact of dispersion quality on the mechanical performance of CNT/Fe₃O₄/Epoxy composites, comparing stirring and sonication methods at three different loadings: 0.1, 0.3, and 0.5 wt.%. Tensile testing revealed that sonicated composites consistently outperformed stirred composites, with a significant increase in elastic modulus and ultimate tensile strength (UTS). However, fracture strain decreased in both composite types compared to pure epoxy, with sonicated composites experiencing a more significant reduction than stirred composites. These results underscore the importance of high-quality dispersion for optimizing mechanical properties.

Refractive index measurements have been an important task for a long time because that index plays an essential role in describing the optical properties of a material. Many methods have been developed to perform that task. Some of them use interferometry to achieve high precision, however these configurations are complicated. Some measure the critical angle using simple structures, but the accuracy is not satisfactory because it is difficult to judge the exact critical angle with intensity variations. Here we propose several new schemes based on measuring the polarization change in the total internal reflection. The proposed method has the merits of simple structure and easy incident angle determination that gives the maximum phase change. Additionally, it is possible to find the material dispersion by measuring the wavelength dependence of the polarization ellipticity. Some useful formulas relating the refractive index with the maximum phase change are obtained. This work can provide valuable alternatives for index measurement.

This paper aims to search for lump waves in a spatial symmetric (2+1)-dimensional dispersive wave model. Through an ansatz on positive quadratic functions, we conduct symbolic computations with Maple to generate lump waves for the proposed nonlinear model. A line of critical points of the lump waves is computed, whose two spatial coordinates travel at constant speeds. The corresponding maximum and minimum values are evaluated in terms of the wave numbers, and interestingly, all those extreme values do not change with time, either. The last section is the conclusion.

Guided ultrasonic waves are suitable for use in the context of structural health monitoring of thin-walled, plate-like structures. Hence, observing the wave propagation in the plates can provide an indication of whether damage has occurred in the structure. In this work, the wave propagation in fiber metal laminate consisting of thin steel foils and layers of carbon fiber-reinforced polymer is studied, focusing on the main propagation characteristics like dispersion diagrams and displacement fields. For this purpose, the dispersion diagrams derived from the analytical framework and numerical simulations are first determined and compared to each other. Next, the displacement fields are computed using the global matrix method for two excitation frequencies. The results derived from the analytical framework is used to validate numerically determined displacement fields based on a 2D and a 3D modeling approach. For both investigations the results of the analytical treatment and the numerical simulation show good agreement. Furthermore, the displacement field reveals the typical and well-known characteristics of the propagation of guided waves in thin-walled structures. Since the use of full 3D models involves a very high computational cost, this work also successfully investigates the possibility for model order reduction to decrease the computational time and costs of the simulation without the loss of accuracy.

A brief review of the history of the problem is intended to trace the progress in the development of scientific views on the structure of water. The discoveries in this area made in the first half of the last century are considered in comparison with modern data. It is shown that due to the de facto ban on the study of the structure of water in 1971, work in this direction was frozen for a long time. The paradox is that many forgotten truths have been independently "rediscovered" in our time, which speaks of their authenticity. On the basis of scientific literature and their own research, the authors come to the conclusion that water under room conditions is a microdispersed system, one phase of which is represented by continuous water, and the other - by polywater, discovered in the 70s of the last century.

Long-term continuous time series of SO2 emissions are considered critical elements of both volcano monitoring and basic research into processes within magmatic systems. One highly successful framework for computing these fluxes involves reconstructing a representative time-averaged SO2 plume from which to estimate the SO2 source flux. Previous methods within this framework have used ancillary wind datasets from reanalysis or numerical weather prediction (NWP) to construct the mean plume and then again as a constrained parameter in the fitting. Additionally, traditional SO2 datasets from ultraviolet (UV) sensors lack altitude information which must be assumed to correctly calibrate the SO2 data and to capture the appropriate NWP wind level which can be a significant source of error. We have made novel modifications to this framework which do not rely on prior knowledge of the winds and therefore do not inherit errors associated with NWP winds. To perform the plume rotation, we modify a rudimentary computer vision algorithm designed for object detection in medical imaging to detect plume-like objects in gridded SO2 data. We then fit a solution to the general time-averaged dispersion of SO2 from a point source. We demonstrate these techniques using SO2 data generated by a newly developed probabilistic layer height and column loading algorithm designed for the Cross-track Infrared Sounder (CrIS), a hyperspectral infrared sensor aboard the Joint Polar Satellite System’s Suomi-NPP and NOAA-20 satellites. This SO2 data source is best suited to flux estimates at high-latitude volcanoes and at low-latitude, but high-altitude volcanoes. Of particular importance, IR SO2 data can fill an important data gap in the UV-based record: estimating SO2 emissions from high-latitude volcanoes through the polar winters when there is insufficient solar backscatter for UV sensors to be used.

Scattering of elastic waves in heterogeneous media has become one of the most important problems in the field of wave propagation due to its broad applications in seismology, natural resource exploration, ultrasonic nondestructive evaluation and biomedical ultrasound. Nevertheless, it is one of the most challenging problems because of the complicated medium inhomogeneity and the complexity of the elastodynamic equations. A widely accepted model for the propagation and scattering of elastic waves, which properly incorporates the multiple scattering phenomenon and the statistical information of the inhomogeneities is still missing. In this work, the author developed a multiple scattering model for heterogeneous elastic continua with strong property fluctuation and obtained the exact solution to the dispersion equation under the first-order smoothing approximation. The model establishes an accurate quantitative relation between the microstructural properties and the coherent wave propagation parameters and can be used for characterization or inversion of microstructures. Starting from the elastodynamic differential equations, a system of integral equation for the Green functions of the heterogeneous medium was developed by using Green’s functions of a homogeneous reference medium. After properly eliminating the singularity of the Green tensor and introducing a new set of renormalized field variables, the original integral equation is reformulated into a system of renormalized integral equations. Dyson’s equation and its first-order smoothing approximation, describing the ensemble averaged response of the heterogeneous system, are then derived with the aid of Feynman’s diagram technique. The dispersion equations for the longitudinal and transverse coherent waves are then obtained by applying Fourier transform to the Dyson equation. The exact solution to the dispersion equations are obtained numerically. To validate the new model, the results for weak-property-fluctuation materials are compared to the predictions given by an improved weak-fluctuation multiple scattering theory. It is shown that the new model is capable of giving a more robust and accurate prediction of the dispersion behavior of weak-property-fluctuation materials. Numerical results further show that the new model is still able to provide accurate results for strong-property-fluctuation materials while the weak-fluctuation model is completely failed. As applications of the new model, dispersion and attenuation curves for coherent waves in the Earth’s lithosphere, the porous and two-phase alloys, and human cortical bone are calculated. Detailed analysis shows the model can capture the major dispersion and attenuation characteristics, such as the longitudinal and transverse wave Q-factors and their ratios, existence of two propagation modes, anomalous negative dispersion, nonlinear attenuation-frequency relation, and even the disappearance of coherent waves. Additionally, it helps gain new insights into a series of longstanding problems, such as the dominant mechanism of seismic attenuation and the existence of the Mohorovičić discontinuity. This work provides a general and accurate theoretical framework for quantitative characterization of microstructures in a broad spectrum of heterogeneous materials and it is anticipated to have vital applications in seismology, ultrasonic nondestructive evaluation and biomedical ultrasound.

Abstract: The air pollution dispersion modelling via spatial analyses (Land Use Regression – LUR) is an alternative approach to the air quality assessment to the standard air pollution dispersion modelling techniques. Its advantages are mainly much simpler mathematical apparatus, quicker and simpler calculations and a possibility to incorporate other factors affecting pollutant’s concentration. The goal of the study was to model the PM10 particles dispersion modelling via spatial analyses v in Czech-Polish border area of Upper Silesian industrial agglomeration and compare results with results of the standard Gaussian dispersion model SYMOS’97. Results show that standard Gaussian model with the same data as the LUR model gives better results (determination coefficient 71% for Gaussian model to 48% for LUR model). When factors of the land cover and were included into the LUR model, the LUR model results were significantly improved (65% determination coefficient) to the level comparable with Gaussian model. The hybrid approach combining the Gaussian model with the LUR gives superior quality of results (65% determination coefficient).

It is currently difficult to obtain accurate fine dust information in residential areas due to the insufficient number of air quality monitoring systems and spatial imbalances. Therefore, a detailed particulate matter dispersion model including factors such as land use and meteorological information was developed in this study and used to create fine dust concentration distribution maps. The fine dust concentration distribution maps currently available to citizens were compared with those obtained by dispersion modeling, and population distribution data were employed to compare the populations exposed to fine dust according to the two methods. The results of the existing method and the developed particulate matter dispersion model differed significantly. For instance, the PM2.5 concentrations in Daejeon, South Korea, on February 17, 2018, were 56% “Good” and 44% “Moderate,” according to the existing method, while they were 31% “Good,” 26% “Moderate,” 28% “Unhealthy,” and 15% “Very Unhealthy,” according to the dispersion model. Furthermore, the existing method indicated that no portion of the population was exposed to poor fine dust concentrations, while the proposed model revealed that over 170 thousand people were exposed to such concentrations. These results on fine dust distributions will contribute to sustainable urban and environmental planning.

Since fine powders tend strongly to adhesion and agglomeration, their processing with conventional methods is difficult or impossible. Typically, in order to enable the handling of fine powders, chemicals are added to increase the flowability and reduce adhesion. This contribution shows that instead of additives also vibrations can be used to increase the flowability, to reduce adhesion and cohesion, and thus to enable or improve processes such as precision dosing, mixing, and transport of very fine powders. The methods for manipulating powder properties are described in detail and prototypes for experimental studies are presented. It is shown that the handling of fine powders can be improved by using low-frequency, high-frequency or a combination of low- and high-frequency vibration.

In this paper we derived an expression that allows the determination of the thermo-optic coefficient of weakly-guiding germanium-doped silica fibers, based on the thermal behavior of optical fiber devices, such as, fiber Bragg gratings (FBGs). The calculations rely on the full knowledge of the fiber parameters and on the temperature sensitivity of FBGs. In order to validate the results, we estimated the thermo-optic coefficient of bulk GeO2 glass at 293 K and 1.55 m to be 18.3x10-6 K-1. The determination of this value required to calculate a correction factor which is based on the knowledge of the thermal expansion coefficient of the fiber core, the Pockels’ coefficients (p11=0.125, p12=0.258 and p44=-0.0662) and the Poisson ratio (=0.161) of the SMF-28 fiber. To achieve that goal, we estimated the temperature dependence of the thermal expansion coefficient of GeO2 and we discussed the dispersion and temperature dependence of Pockels’ coefficients. We have presented expressions for the dependence of the longitudinal and transverse acoustic velocities on the GeO2 concentration used to calculate the Poisson ratio. We have also discussed the dispersion of the photoelastic constant. An estimate for the temperature dependence of the thermo-optic coefficient of bulk GeO2 glass is presented for the 200-300 K temperature range.

Spray technology is widely used in various industries, including medicine, food production, mechanical engineering, and nanopowder manufacturing. Achieving high dispersion and a narrow particle size distribution is crucial for many applications. Ultrasonic spraying is commonly used to achieve this. On other hand, hydraulic nozzles provide high atomization performance. Combining these two technologies promises to offer significant benefits, but the complex processes that occur simultaneously in such a device require careful study. This work proposes a fundamental design for an acoustic-hydraulic nozzle and investigates the physical processes when a liquid is sprayed using this nozzle, both theoretically and experimentally. The study identifies the critical modes of spraying and confirms that the simultaneous use of ultrasound and hydraulic pressure can produce a fine spray (droplet size less than 50 μm) with high productivity (5-10 ml/s). This approach has significant potential for modern industries and technologies.

In natural, laboratory and industrial conditions, the density of a fluid or gas, depending on temperature, pressure, concentration of dissolved substances or suspended particles, changes under the influence of a large number of physical factors. We assume that undisturbed liquid is stratified. The analysis is based on a system of fundamental equations for the transfer of energy, momentum and matter in periodic flows of a viscous compressible fluid. The propagation of periodic flows in viscous uniformly stratified fluids is considered. Taking into account the compatibility condition, dispersion relations are constructed for two-dimensional internal, acoustic and surface linear disturbances with a positive definite frequency and complex wave number in a compressible viscous fluid exponentially stratified by density. The temperature conductivity and diffusion effects are neglected. The obtained regularly perturbed solutions to the equations describe weakly damped waves. Singular solutions characterize the thin ligaments that accompany each type of wave. In limiting cases, the constructed solutions transform into known expressions for a viscous homogeneous and ideal fluid or degenerate.

Background. COVID-19 efforts were often ineffective in controlling the spread of the pandemic. Identifying ineffective controls during a pandemic is thus vital. Method. Utilizing publicly available data on COVID deaths in the counties of US states, we create an index to capture and interpret ineffectiveness in the efforts to reduce the spread of the pandemic in US counties. This index is based on the Intervened Poisson Distribution (IPD) introduced originally by Shanmugam. Motivation for the research idea occurred while we noticed the data dispersion of the COVID deaths is smaller than the average only in some counties. Under-dispersed data is common in statistical modeling. A novel approach we adapted in this article includes the estimation of an intervention parameter estimated through iterative non-linear optimization. Results. Twenty-five counties in California, Idaho, Minnesota, Mississippi, Montana, Nebraska, North Carolina, North Dakota, Texas, and Utah were found to be ineffective in controlling for fatalities based on the expected probability distribution. A review of the policies enacted in these areas would provide insight into ineffective prevention efforts, and some of these issues are documented in current literature. Conclusion. The IPD index an innovate way to document efficacy of interventions during pandemics. The IPD may identify ineffective efforts prior to statistical models intended to evaluate efficacy of efforts.

The density functional theory was used to explore the structural, electronic, dynamical, and thermoelectric properties of a VIrSi Half-Heulser (HH) alloy. The minimum lattice constant of 5.69 ( ̊A) was obtained for VIrSi alloy. Besides, the band structure and the projected density of states for this HH alloy were calculated, and the gap between the valence and conduction bands was noted to be 0.2 eV. Also, the quasi-harmonic approximation was used to predict the dynamical stability of the VIrSi HH alloy. At 300 K, the Seebeck Coefficient of 370 and -270 μV.K−1., respectively, was achieved for the p and n-type doping. From the power factor result, the highest peak of 18 X 1011W/cm.K2 is obtained in the n-type doping. The Figure of Merit (ZT) result revealed that VIrSi alloy possesses a high ZT at room temperature, which would make VIrSi alloy applicable for thermoelectric performance.

Melt mixing is a convenient method to prepare polymer nanocomposites, but the extent of the dispersion of the solid filler reached is often limited, and may compromise the anticipated performance of these materials during service. Since the efficiency of extensional flows on dispersion is now well recognized, several mixers were designed with the aim of inducing both shear and extensional flow components. This work combines experimental and numerical data to better understand the kinetics of the dispersion of graphite nanoplates in a polypropylene melt, using a mixing device that consists of a series of stacked rings with equal outer diameter and alternating larger and smaller inner diameters, thus creating a series of converging/diverging flows. Numerical simulation of the flow using the opensource OpenFOAM software assuming both inelastic and viscoelastic responses predicted the velocity, streamlines, flow type and shear and normal stress fields for the mixer. Experimental and computed data were combined to determine the trade-off between the local degree of dispersion of the PP/GnP nanocomposite, measured as Area ratio, and the absolute average value of the hydrodynamic stresses multiplied by the local cumulative residence time. From considerations based on a theoretical approach to dispersion, the cohesive strength of the GnP agglomerates studied was estimated to be in the range 3 - 10kPa.

The wave packet consisting of two harmonic plane waves with the same frequencies, but with different wave vectors is considered. The dispersion relation of a packet is structurally similar to the dispersion relation of a relativistic particle with a nonzero rest mass. The possibility of controlling the group velocity of a quasi-monochromatic wave packet by varying the angle between the wave vectors of its constituent waves is discussed.

Pharmaceuticals contain biologically active components that can pollute water courses as a result of the excretions from individuals and/or uncontrolled release of residues from chemical plants, and they can pose a hazard to health. Pharmaceutical residues can persist at low concentrations in the environment, and thus may be potentially harmful to aquatic animals and to humans. Controlling and monitoring such residues are therefore a prime interest, for example, a solid-phase extraction uses solid sorbents to purify and preconcentrate the residues prior to their chemical analysis. In the present study, poly (acrylonitrile-co-divinylbenzene-80) sorbents are synthesised by varying the comonomer feed ratios under precipitation polymerisation conditions to deliver a family of porous polymer microspheres. Acrylonitrile confers polar characters onto the sorbents, and the acrylonitrile-derived nitrile groups can be chemically transformed via polymer-analogous reactions into thioamide and sulfonated residues which make the sorbents even more suitable for the capture of polar analytes, including selected pharmaceuticals. The utility of the porous thioamide-sulfonated containing sorbents is demonstrated via the dispersion-solid phase extraction of mefenamic acid from aqueous media; mefenamic acid is an anthranilic acid derivative which is a potent, non-steroidal anti-inflammatory drug which is found in environmental waters at low concentrations.

Extraction of high-resolution surface waves is essential in surface-wave survey. Because reflections usually interfere with surface waves on X component in a multicomponent seismic exploration, it is difficult to extract dispersion curves of surface waves. The situation goes more serious when the frequencies and velocities of higher-mode surface waves are close to those of PS-waves. A method for surface-wave extraction is proposed based on the morphological differences between reflections and surface waves. Frequency-domain high-resolution linear Radon transform (LRT) and time-domain high-resolution hyperbolic Radon transform (HRT) are used to represent surface waves and reflections respectively. Then, the sparse representation problem based on the morphological component analysis (MCA) is built and optimally solved to obtain high-fidelity surface waves. An advantage of our method is its ability to extract surface waves when their frequencies and velocities are close to those of reflections. Furthermore, results of synthetic and field examples confirm that the proposed method can attenuate the distortion of surface-wave dispersive energy caused by reflections, which contributes to extracting accurate dispersion curves.

The sustainability of irrigated agriculture depends on the quality of irrigation water used. The electrolyte concentration (EC) of irrigation water may lead to the accumulation of salts in the root zone layers and affect the physiological functions of the crop by osmotic and ion toxicity effects. Further, the cationic and anionic composition of the water may alter the exchangeable cation composition of the soil and as well as its pH. Because of the dominance of sodium salts in many sources of irrigation water, parameters related to sodium such as exchangeable sodium percentage (ESP) of soils and sodium adsorption ratio (SAR) of soil solutions have been commonly used to study the effects of sodium in irrigation water on soil structural stability. Quirk and Schofield concept of ‘threshold electrolyte concentration’ (TEC) has shown the importance of electrolytes in preventing the effects of sodium on soil structure. Based on this concept, several models have been proposed to relate ESP or SAR with EC to predict the possible impacts of irrigation water on soil structural stability. However, many research reports indicate that this relationship varies with soils and a given model is not suitable for all types of soils. Further, the effects of potassium and magnesium in the processes leading to clay dispersion are disregarded in these models. This essay analyses all the factors involved in the structural failure of soils with different cationic composition, identify the defects in these TEC models and re-defines TEC on the basis of new insights on dispersive and flocculating charges of soils. This review does not deal with EC effects on crops and also the role of contaminant ions not involved with soil structural stability.

The precise prediction of air contaminant dispersion is essential to the air quality monitoring and the emergency management of the contaminant gases leakage incidents in the chemical industry park. The conventional atmospheric dispersion models can seldom give precise prediction due to inaccurate input parameters. In order to improve the prediction accuracy of dispersion model, two data assimilation methods (i.e. one is merely based on the typical particle filter while the other is a combination of particle filter and expectation-maximization algorithm) are proposed to assimilate the UAV observations into the atmospheric dispersion model. Two emission cases are taken into consideration, the difference between which is the different dimensions of state variables. To test the performances of the proposed methods, experiments corresponding to the two emission cases are designed and implemented. The results show that the particle filter can effectively estimate the model parameters and improve the accuracy of model prediction when the dimension of state variables is low. In contrast, when the dimension of state variables becomes higher, the method of particle filter combining expectation-maximization algorithm performs better in the parameter estimation accuracy and warm-up time. Therefore, the data assimilation methods are able to effectively support the air quality monitoring and emergency management in chemical industry parks.

The removal of chromium(VI) from acidic (HCl) medium through non-dispersive extraction with strip dispersion (NDXSD) was investigated using a microporous PVDF membrane support in a permeation cell. The ionic liquid Cyphos IL102 (phosphonium salt) in Solvesso 100 was used as organic phase. In NDXSD the stripping phase (NaOH) is dispersed in the organic phase in the cell side with an impeller stirrer adequate to form a strip dispersion. This pseudo-emulsion phase (organic + strip solutions) provides a constant supply of the Cyphos IL102/Solvesso 100 to the membrane phase. Various hydrodynamic and chemical parameters, such as variation in the feed and pseudo-emulsion stirring speeds, HCl and Cr(VI) concentrations in the feed phase, and carrier concentration, were investigated. From the experimental data, several mass transfer coefficients were estimated, as well as it was investigated the performance of the present system against other ionic liquids and the presence of base metals in the feed phase.

Theoretical studies on the generation of nondiffracting and nondispersive light pulses and their experimental implementation are one of the renowned problems within electromagnetics. Current technologies enable creation of short-duration pulses of a few cycles with high power and fluency. An application of these techniques to the field of nondiffracting and nondispersive pulses requires a proper mathematical description of highly focused vector pulses. In this work, we study vector optical bullets in a dielectric medium with different polarization structures: linear, azimuthal, and radial. We report the differences caused by the vector model compared to the scalar model. We analyze effects caused by superluminal, subluminal, or even negative group velocity on properties of vector optical bullets inside a dielectric material.

The jet-slit milk homogenizer is one of the most energy-efficient among all types of homogenizers in the dairy industry. The principle of its operation is based on the creation of a maximum speed difference between the fat globules of cream and the flow of skimmed milk. Reducing the specific energy consumption and finding the optimal parameters of the homogenizer were based on the results of both theoretical and experimental studies. The optimization criteria (decreasing specific energy consumption while maintaining high homogenization quality) were chosen to achieve a dispersion of 0.8 μm with minimal energy consumption. The parameters of the width of the ring gap, the fat content and the speed of the cream have been optimized. It is possible to reduce the specific energy intensity of the process to values of 0.88–0.92 kWh/t when using cream with a fat content of 33–43%, which should be fed through an annular gap with a width of 0.6–0.8 mm. Optimum values of the cream feed speed had been found, which should be equal to 7–11 m/s. The research results are of high practical value for the further development of the energy-efficient industrial model of a jet-slit homogenizer.

Mechanochemical technology is developing rapidly, judging by the scientific information in both basic and applied studies. However, many issues and points of view remain to be discussed. This review presents some new key issues for the optimization of mechanochemical processes in theoretical and practical aspects. Emphasis is placed on powder technology aspects, which are not always discussed compared to functional or microscopic viewpoints. The transfer of chemical species across the interparticle interface between organic and inorganic species during the mechanosynthesis of nanocomposite oxides offers many new possibilities, which are discussed here in detail. Since all material transport is preceded by charge transfer, its driving force has been searched for using terminology beyond the well-established electrochemical ones. The role of organic compounds during the whole process is emphasized, regardless of their survival in the final product. The similarity with the pharmaceutical phenomena is pointed out, although its mentality is very different from that of the synthesis of nanocomposites. Not only for the rational amorphization of the active pharmaceutical ingredient, but also for the stabilization of molecular dispersion states with the participation of excipients are discussed. The effects of liquids, either added or formed by mechanochemical auto-liquefaction, are presented with reference to the comparison between wet and dry grinding. Finally, mechanisms of apparent stabilization of mechanically activated states of products are elucidated to investigate the practical applicability of mechanochemically synthesized products

We evaluated the change in water dispersibility of lactic acid bacteria (LAB, Enterococcus faecalis KH2) upon powderization and its influence on their efficacy. When cultured LAB are washed, heat-killed, and powdered, adhesion between LAB occurs and they form aggregation (non-treated LAB, n-LAB). However, a dispersed LAB (d-LAB) powder with less aggregates can be prepared by treating them with a high-pressure homogenizer and adding an excipient during powdering. n-LAB or d-LAB was administered to mice and the Peyer's patches in the small intestine were observed. n-LAB administration showed a high amount of aggregated LAB drifting in the intestinal mucosa, whereas d-LAB reached the Peyer's patches and was taken up into the Peyer's patches. Evaluation in a mouse influenza virus infection model showed that d-LAB was more effective than n-LAB in influenza yield of bronchoalveolar lavage fluids (BALFs) on day 3 post-infection, neutralizing antibody titers of sera and influenza virus-specific IgA in the feces on day 14 post-infection. Thus, the physical properties of LAB affect their efficacy; controlling their water dispersibility can improve their effectiveness.

This article reveals a best possible design for hybrid dispersion compensating fiber (HyDCF) with high birefringence established on modified broadband compensating structure through S, C and L telecommunication bands. The simulation outcome exhibits relatively higher birefringence of 3.76×10-2 at wavelength of 1550 nm. The suggested fiber also has dispersion compensation characteristics in an inclusive series of wavelengths which covers 1400-1625 nm. The reported design can achieve dispersion quantity of – 606 ps/ (nm.km) at 1550 nm effective wavelength. The reported fiber design matches the relative dispersion slope (RDS) 0.003694 nm-1 similar to single mode fiber at 1550 nm operating wavelength. This fiber demonstrates negatively flattened effective dispersion of – 2.703 ± 0.734 ps/ (nm.km) within 180 nm flat band ranging from 1460-1640 nm wavelength. It is also convenient to optical high bit rate communication systems. The low confinement loss is found 3.756×10-10 dB/m at the operating wavelength. This design also achieves highly nonlinear coefficient of 50.34 W-1km-1. In some cases, it can also be used in sensing applications.

This work intends to present a study on relations between a Lie algebra called dispersion operators algebra, linear canonical transformation and a phase space representation of quantum mechanics that we have introduced and studied in previous works. The paper begins with a brief recall of our previous works followed by the description of the dispersion operators algebra which is performed in the framework of the phase space representation. Then, linear canonical transformations are introduced and linked with this algebra. A multidimensional generalization of the obtained results is given.

Since the advent of Fourier Domain Mode-Locked (FDML) lasers, they have demonstrated outstanding performance in several fields. They achieve high-speed, narrow-linewidth laser output with the new mode-locking mechanism, which has been intensively researched in the past decades. Compared with conventional wavelength-scanning light sources, FDML lasers have successfully increased the scanning rate of frequency-sweeping lasers from kHz to MHz. They are widely used in optical coherence tomography, spectral analysis, microscopy, measurement, and microwave signal generation. With the deepening research on FDML lasers, several performance metrics have been optimized and improved, offering superior performance for FDML laser-based applications. This paper reviews the principles and key performance indicators of FDML lasers, as well as the recent progress made in some important applications, and highlights further research directions for FDML lasers in the future.

The fall armyworm (FAW), Spodoptera frugiperda, a major pest in maize production, was assessed for its temporal and spatial distribution in maize fields during both the off and rainy seasons of 2021 and 2022. In this study, 30 and 50 maize plants were randomly sampled using a "W" pattern during the dry and rainy seasons, respectively. Larval density, infestation rates, and damage severity were monitored over time. Taylor's power law and the mean crowding aggregation index were applied to evaluate the dispersion patterns of the larvae. The results indicate a higher infestation rate and larval density in agroecological zone AZE 8 (fisheries zone of South Benin) compared to AZE 6 (ferralitic soils zone) during the off-season. In the rainy season, while the percentage of damaged plants was higher in AZE 8, no significant differences in larval density between the two zones were observed. The dispersion analysis revealed moderate aggregation (aggregation index = 1.25) with a basic colony of 2.08 larvae, reflecting the aggregation oviposition behavior of FAW. This study provides valuable monitoring data on the FAW's distribution, offering insights for further research on population dynamics and developing predictive models for integrated pest management strategies.

The article presents the results of research work devoted to improving the characteristics of paint and varnish coatings based on aqueous dispersions of polyacrylates, it is proposed to modify them by introducing mineral raw materials as fillers and hydrated lime with subsequent processing in a vortex layer apparatus. Introduction of activated diatomite does not cause deterioration of covering power, adhesion and increase of porosity of the paint material. Modification of coatings contributes to the increase of their operational properties, which can be associated with the reduction of free volume in the composite, formation of polymer boundary layers with modified physical and chemical properties. The aim of the study is to obtain water-dispersion paint and varnish composition containing modified diatomite on polyacrylate basis and subsequent study of the main physical and mechanical parameters. The work has been carried out by the following method: determination of porosity, adhesion, elasticity, covering power of the control composition; determination of porosity, adhesion, elasticity, and covering power of the obtained composites using modified filler; investigation of the influence of radiation in the infrared spectrum of the paint coating surface using FLIRB620 thermal imager. As a result of research works it was noticed that modification of water dispersions with silica activated diatomite helps to eliminate the main disadvantages of materials and coatings based on acrylate binder - low water resistance and low physical and mechanical characteristics, introduction of modified diatomite into water emulsion paint on acrylate base does not lead to deterioration of the main performance characteristics of paint coatings - porosity, adhesion, elasticity and covering.

This study employs the FLACS code to analyze hydrogen leakage, vapor dispersion, and subsequent explosions. Utilizing pseudo-source models, a liquid pool model, and a hybrid model combining both, we investigate dispersion processes for varying leak mass flow rates (0.225 kg/s and 0.73 kg/s) in a large open space. We also evaluate explosion hazards based on overpressure and impulse effects on humans. The computational results, compared with experimental data, demonstrated reasonable hydrogen vapor cloud concentration predictions, especially aligned with the wind direction. For higher mass flow rate of 0.73 kg/s, the pseudo-source model and hybrid model proved appropriate, while the liquid pool model was more suitable for lower mass flow rate of 0.225 kg/s. Regarding explosion analyses using overpressure-impulse diagram, higher mass flow rates leaded to potentially fatal overpressure and impulse effects on humans. However, lower mass flow rates may cause severe eardrum damage at the maximum overpressure point.

In tire tread applications, achieving enhanced abrasion resistance, wet grip, and rolling resistance is crucial for optimizing overall performance. To realize improvements in these attributes for silica-filled tire tread compound, it becomes imperative to improve dispersity of silica filler with investigating the effect of each component in tire tread compound. In this work, we study the effect of styrene content within solution styrene butadiene rubber (SSBR) on the properties of tire tread compounds. A higher styrene segment within SSBR contributes to increased silica dispersion and crosslink density. Thus, tire tread compounds featuring SSBR with increased styrene content not only improve physical and mechanical properties but also enhance major characteristics tailored for tire tread applications. These findings provide valuable insights into advancing the reinforced performance of tire tread compounds through the strategic utilization of SSBR enriched in styrene content.

We consider the propagation of electromagnetic waves in the Friedman – Lemaître – Robertson – Walker metric. The exact solutions for plane and spherical wave are written down. The corresponding redshift, amplitude change, and dispersion are discussed. We also speculate about the connection of the electromagnetic wave equation to the Klein–Gordon equation.

This study aimed to develop chitosan-based apigenin spray dried solid dispersion using 1:1,1:1.5,1:2 w/w ratios. The results of process yield and drug assay were found to be (87.5%, 94.2%, and 95.86%), (95.2 ±1.34%), (99.5 ±0.85%), and (97.6 ±2.42%), respectively, for AC1, AC2, and AC3. Flow properties indicate the free flow of powders. FTIR revealed compatibility among chitosan and apigenin, and DSC and XRD showed prepared solid dispersion was on a molecular level and available in amorphous. In contrast, SEM images reflect irregular block and near-spherical shape elongated particles in the selected AC2. The antimicrobial examination reflects that AC2 was more effective against Gram-positive, negative, and fungal strains. AC2 SDSDs has more anti-oxidant property compared to pure flavonoid (AGN). Anti-proliferative activity against A549 lung cancer cell lines showed better anti-cancer activity by AC2 SDSDs. The selected AC2 SDSD filled in a 3D shell pill and further characterized for 3D shell pill for dissolution profiles and stability studies. The product has sustained release and similar release profiles after three months of storage. The findings suggest that the AC2 SDSDs may be a promising candidate for further development as a 3D printed drug delivery system for treating multiple disease conditions using model flavonoid- apigenin.

Seismic travel time tomography using surface waves is an effective tool for three-dimensional crustal imaging. Historically, these surface waves are the result of active seismic sources or earthquakes. More recently, however, also surface waves retrieved through the application of seismic interferometry are exploited. Conventionally, two-step inversion algorithms are employed to solve the tomographic inverse problem. That is, a first inversion results in frequency-dependent, two-dimensional maps of phase velocity, which then serve as input for a series of independent, one-dimensional frequency-to-depth inversions. As such, a two-dimensional grid of localized depth-dependent velocity profiles are obtained. Stitching these separate profiles together subsequently yields a three-dimensional velocity model. Relatively recently, a one-step three-dimensional non-linear tomographic algorithm has been proposed. The algorithm is rooted in a Bayesian framework using Markov chains with reversible jumps, and is referred to as transdimensional tomography. Specifically, the three-dimensional velocity field is parameterized by means of a polyhedral Voronoi tessellation. In this study, we investigate the potential of this algorithm for the purpose of recovering the three-dimensional surface-wave-velocity structure from ambient noise recorded on and around the Reykjanes Peninsula, southwest Iceland. To that end, we design a number of synthetic tests that take into account the station configuration of the Reykjanes seismic network. We find that the algorithm is able to recover the 3D velocity structure at various scales in areas where station density is high. In addition, we find that the standard deviation on the recovered velocities is low in those regions. At the same time, the velocity structure is less well recovered in parts of the peninsula sampled by fewer stations. This implies that the algorithm successfully adapts model resolution to the density of rays. Also, it adapts model resolution to the amount of noise on the travel times. Because the algorithm is computationally demanding, we modify the algorithm such that computational costs are reduced while sufficiently preserving non-linearity. We conclude that the algorithm can now be applied adequately to travel times extracted from (time-averaged) station-station cross correlations by the Reykjanes seismic network.

Is it possible to measure the dispersion of ex-ante chances (i.e. chances “before the event”) among people, be it gambling, health, or social opportunities? We explore this question and provide some tools, including a statistical test, to evidence the actual dispersion of ex-ante chances in various areas with a focus on chronic diseases. Using the principle of maximum entropy, we derive the distribution of the risk to become ill in the global population as well as in the population of affected people. We find that affected people are either at very low risk like the overwhelming majority of the population but still were unlucky to become ill, or are at extremely high risk and were bound to become ill.

In this paper, design of optical spectral filters based on mode coupling of optical fibers is presented. The finite difference method is applied to find the dispersion characteristics of optical fiber coupler constructing from two fibers as a composite multi-dielectric waveguide with different cores but the same cladding. Also, the field distribution for both fibers as a separate and as a composite waveguide. The spectral characteristics of the filters are investigated depending on the coupling of two linear polarized modes LP01 and LP11. The dependence of the transmission coefficient on operating wavelengths is illustrated. Finally, the spectral bandwidth of filter as a function of the distance between the two cores is addressed.

Abstract: Composite sintered bodies comprising silicon dioxide (SiO2) nanoparticles dispersed in β-tricalcium phosphate (β-TCP) were prepared. The addition of nano-sized colloidal SiO2 to the β-TCP produced well-dispersed secondary phase nanoparticles that promoted densification by suppressing grain growth and increasing volume shrinkage of the sintered bodies. The SiO2 was found not to react with the β-TCP at 1120 °C and the substitution of silicon for phosphorous to produce a solid solution did not occur. This lack of a reaction is ascribed to the absence of avail-able calcium ions to compensate for the increase in charge associated with this substitution. The SiO2 nanoparticles were found to be present near the intersections of grain boundaries in the β-TCP. A β-TCP composite sintered body containing 4.0 wt% SiO2 exhibited a bending strength comparable to that of cortical bone and hence could potentially be used as a bone filling material.

Location-and-scale transformation of a random variable underpins normal distribution, but it is however fundamentally incorrect for scale estimation such as relative dispersion. In this paper, a parametrized alternative to a normal distribution, called scaloc-normal distribution, is proposed that efficiently works and is fundamentally correct with absolute and relative dispersion estimators. The Monte Carlos simulation experiment was used to generate a total of 600,000 artificial datasets in 600 different simulation scenarios from loc-normal (normal) and scaloc-normal distributions. The absolute and relative dispersion were estimated and compared from the two distributions. The results show that scaloc-normal distribution is a good parametrized alternative to loc-normal distribution, fundamentally correct and efficient with both standard deviation and coefficient of variation. The key statistical advancement from loc-normal to scaloc-normal distribution is its fundamental correctness (i.e., scale-invariant property) with an efficient relative estimator of dispersion (i.e., coefficient of variation). Parametrically, the loc-normal and scaloc-normal distributions are very different, but both have linear transformations.

Reactive transport (RT) couples bio-geo-chemical reactions and transport. RT is important to understand numerous scientific questions and solve some engineering problems. RT is highly multidisciplinary, which hinders the development of a body of knowledge shared by RT modelers and developers. The goal of this paper is to review the basic conceptual issues shared by all RT problems, so as to facilitate advance along the current frontier: biochemical reactions. To this end, we review the basic equations to point that chemical systems are controlled by the set of equilibrium reactions, which are easy to model, but whose rate is controlled by mixing. Since mixing is not properly represented by the standard advection-dispersion equation (ADE), we conclude that this equation is poor for RT. This leads us to review alternative transport formulations, and the methods to solve RT problems using both the ADE and alternative equations. Since equilibrium is easy, difficulties arise for kinetic reactions, which is especially true for biochemistry, where numerous frontiers are open (how to represent microbial communities, impact of genomics, effect of biofilms on flow and transport, etc.). We conclude with the basic 10 issues that we consider fundamental for any conceptually sound RT effort.

Intermetallic alloys like e.g. Iron-Aluminides, Titanium-Aluminides or Molybdenum- Silizides are prospective materials for high-temperature applications. For additive manufacturing (AM) intermetallic structural materials are particularly challenging due to their high melting points, oxygen susceptibility and low temperature brittleness. The feasibility of manufacturing intermetallic Mo-Si-B alloys with the laser additive manufacturing process of direct energy deposition (DED) is demonstrated and recent results in characterizing rapidly solidified material with respect to correlations between process, composition and microstructures are presented. The possibility to dope the material with Yttrium oxide (Y2O3) for dispersion is successfully demonstrated. Current challenges, e.g. homogenous distribution of alloying elements and applicability are addressed.

Downwind odor characteristics can be very different depending upon the size of the upwind point-source, interim topography, and wind conditions. At one extreme, the downwind odor plume from a relatively large, confined animal feeding operation (CAFO), located on a flat open plain and under stable, near-straight-line wind conditions can be rather broad, sustained and predictable relative to a fixed receptor site downwind. In contrast, the plume from a small point-source (e.g., a roof vent stack) located on irregular topography and under rapidly shifting wind conditions can be intermittent and fleeting. These transient odor events can be surprisingly intense and offensive, in spite of their fleeting occurrence and perception. This work reports on efforts to optimize an environmental odor sampling strategy, which is optimized for the challenges of (1) sampling of such transient odor 'spikes' and (2) the prioritization of odors/odorants from multiple, closely co-located point-sources, under such transient event conditions. Protocol refinement has emerged by way of 2 environmental odor assessment projects which have been undertaken on behalf of the Missouri Department of Natural Resources. The challenge of transient odor events has been mitigated utilizing rapid, odor cued whole-air grab capture sampling into metalized-FEP gas sampling bags, followed by immediate adsorption transfer onto SPME fibers or sorbent tubes for stabilization during the shipment and storage interval between collection and final analysis. Initial results demonstrated approximately 11 fold increases in target odorant yields for 900 mL sorbent tube transfers from 2-3 second 'burst' odor event bag-captures, as compared to equivalent direct collections at the same downwind receptor location but during perceived (stable) odor 'lull' periods. Results-to-date targeting refinement and field trials of this integrated environmental odor assessment strategy are presented. Preliminary application targeting general odor sampling and point-source differentiation utilizing tracer gases is also presented.

In any region of a space, the gravitational field cannot be eliminated. The speed of light in a vacuum has never been observed and cannot be observed with current technology. Till now, only the speed of light in a gravitational field has been observed. It results in that all the observed speed of light are always being varied by the gravity. Here, it is presented that light could be dispersion in a gravitational field analogous to the dispersion of light in the Newtonian prism experiment. The relativistic mass density on the surface of a neutron star is on the level of 10¹⁷kg/m³ while on the surface of the Earth is only 10^-7kg/m³, the effect of the gravitational field acting on the speed of light by a neutron star is much larger than that by the Earth. Therefore, the dispersion of light in strong gravitational field could be generally observed from the image of a star and it should have been observed through the double-image gravitational lensing and the spectroscopic binary system. And, it should affect the observed numbers, spectrogram, size and distance of the celestial objects.

Pigment dispersion can lead to pigmentary glaucoma, a poorly understood condition of younger myopic eyes with fluctuating high intraocular pressure. It has been difficult to investigate its pathogenesis without a model similar to human eyes in size and behavior. Here we present a porcine ex vivo model that recreates several features of pigmentary glaucoma, including intraocular hypertension, accumulation of pigment in the trabecular meshwork, and declining phagocytosis. We found that trabecular meshwork cells regulate outflow, form actin stress fibers, and have a decreased phagocytic activity. Gene expression microarrays and a pathway analysis of TM monolayers as well as ex vivo anterior segment perfusion cultures indicated that RhoA plays a central role in regulating the cytoskeleton, motility, and phagocytosis in the trabecular meshwork, providing new insights and targets to investigate in pigmentary glaucoma.

The review scrutinizes the currently performed research on the new methods for enhancing bituminous binder performance through radiation and radical grafting of polymer modifers of bitumen. It investigates innovative methods, including using waste polymers as modifiers, and applying radiation for polymer grafting, to overcome challenges like high costs, low aging resistance and storage stability issues, of which separation of phases polymer/bitumen is the most significant obstacle. These advanced modification techniques promise sustainability through the decrease of the carbon footprint of transportation systems by improving the properties and durability of binders. Additionally, the review discusses the parameters and mechanistic aspects from a scientific perspective, shedding light on the underlying processes that contribute to the improved performance of modified bituminous binders.

A comprehensive theory is developed for the chiral optical response of two configurations of the N-oscillator Born-Kuhn model (NOBK): the helically stacked and the corner stacked models. In the helical NOBK model, there is always a chiral response regardless of the value of N, whereas in the corner NOBK, only configurations with even N demonstrate a chiral response. Generally, the magnitudes of optical rotatory dispersion (ORD) and circular dichroism (CD) increase with N when the parameters of each oscillator are fixed. In cases of weak coupling, the spectral shapes of ORD and CD remain invariant, while strong coupling significantly alters the spectral shapes. For large damping, the spectral amplitude becomes smaller, and the spectral features become broader. In the presence of small damping, strong coupling introduces degeneracy in the coupled oscillator system, leading to multiple spectral features in both ORD and CD across the entire spectral region. This simple model not only can help in the design of tunable chiral metamaterials but also enhance our understanding of chiro-optical responses in structures with different configurations.

Phenol is added to acetophenone (methyl phenyl ketone) and to six of its halogenated derivatives in a supersonic jet expansion to determine the hydrogen bonding preference of the cold and isolated 1:1 complexes by linear infrared spectroscopy. Halogenation is found to have a pronounced effect on the docking site in this intermolecular ketone balance experiment. The spectra unambiguously decide between competing variants of phenyl group stacking due to their differences in hydrogen bond strength. Structures where the phenyl group interaction strongly distorts the hydrogen bond are more difficult to quantify in the experiment. For unsubstituted acetophenone, phenol clearly prefers the methyl side despite a predicted sub-kJ/mol advantage which is nearly independent of zero point vibrational energy, turning this complex into a challenging benchmark system for electronic structure methods which include long range dispersion interactions in some way.

When it comes to air pollution complaints, odours are often the most significant contributor. Sources of odour emissions range from natural to anthropogenic. Mitigation of odour can be challenging, multifaceted, site-specific, and is often confounded by its complexity—defined by existing (or non-existing) environmental laws, public ordinances, and socio-economic considerations. The objective of this paper is to review and summarize odour legislation in selected European countries (France, Germany, Austria, Hungary, United Kingdom, Spain, The Netherlands, Italy, Belgium), North America (USA and Canada), South America (Chile and Colombia), as well as Oceania (Australia and New Zealand) and Asia (Japan, China). Many countries have incorporated odour controls into their legislation. However, odour-related assessment criteria tend to be highly variable between countries, individual states, provinces and even counties and towns. Legislation ranges from (1) no specific mention in environmental legislation that regulates pollutants which are known to have an odour impact to (2) extensive details about odour source testing, odour dispersion modeling, ambient odour monitoring, (3) setback distances, (4) process operations, and (5) odour control technologies and procedures. Agricultural operations are one specific source of odour emissions in rural and suburban areas and a model example of such complexities. Management of agricultural odour emissions is important because of the dense consolidation of animal feeding operations and the advance of housing development into rural areas. Overall, there is a need for continued survey, review, development, and adjustment of odour legislation that considers sustainable development, environmental stewardship, and socio-economic realities, all of which are amenable to a just, site-specific, and sector-specific application.

Purpose: To investigate the effect of pigment dispersion on trabecular meshwork (TM) cells. Methods: Porcine TM cells from ab interno trabeculectomy specimens were exposed to pigment dispersion, then analyzed for changes in morphology, immunostaining, and ultrastructure. Their abilities to phagocytose, migrate, and contract were quantified. An expression microarray, using 23,937 probes, and a pathway analysis were performed. Results: TM cells readily phagocytosed pigment granules. Pigment induced stress fiber formation (pigment (P): 60.1 ± 0.3%, n = 10, control (C): 38.4 ± 2.5%, n = 11, P < 0.001) and contraction at 24 hours onward (P < 0.01). Phagocytosis declined (P: 68.7 ± 1.3%, C: 37.0 ± 1.1%, n = 3, P < 0.001) and migration was reduced after 6 hours (P: 28.0.1 ± 2.3, n = 12, C: 40.6 ± 3.3, n = 13, P < 0.01). Microarray analysis revealed that Rho, IGF-1, and TGFβ signaling cascades were central to these responses. Conclusions: TM cell exposure to pigment dispersion resulted in reduced phagocytosis and migration, as well as increased stress fiber formation and cell contraction. The Rho signaling pathway played a central and early role, suggesting that its inhibitors could be used as a specific intervention in treatment of pigmentary glaucoma.

In this study the distribution of heavy metal in the agricultural soils in the vicinity of 3 large mine-landfills around Kizhnica mine in Kosovo was investigated. The mining sector is one of the most important sectors of the economic development of Kosovo. The Kizhnica mine is one of the main ore producers in Kosovo. In addition to the positive aspects of production development it has its own side effects such as: industrial waste and the possibility of contamination of sur-rounding areas including the agricultural lands in the surrounding region. Ten sampling sites close to the Kizhnica mining complex were selected. These sampling sites have been characterized and evaluated as the most critical points, due to the anthropogenic influences of the discharge of industrial water from mining flotation and open tailing dumps in the Kizhnica. Concentration of Pb, Zn, Cu, As, Cd, Ni, Mn and Sb in selected samples was carried out by inductively coupled plasma–optical emission spectrometry (ICP–OES). Obtained data were used in order to generate geochemical maps and for calculatation the contamination factor (CF), pollution load index (PLI) and geo-accumulation index (Igeo). The statistical clustering analysis (CA), Pearson correlation coefficient (r) and air spatial distribution patterns using AERMOD View-Gaussian air dispersion model are used to perform evaluation within the area. The results demonstrated higher contents of the heavy metals in the vicinity of the mining area. It may be concluded that the heavy metal contents are impacted by anthropogenic nature of the contamination that confirms a current eco-logical threat of the mining activities in the region. Finally, a paper proposes the potential reas-signment of the deposed waste material into different combinations in construction in order to enhance the waste management and reduce the continued risk to: residents, lands and all living beings in the region.

This research employs a spatial optimization approach customized for addressing equitable emergency medical facility location problems, through the p-dispersed-median problem (p-DIME). The p-DIME integrates two conflicting classes of spatial optimization problems, dispersion, and median problems, aiming to identify the optimal locations for emergency medical facilities to achieve a balanced spatial distribution of emergency medical services (EMS) while effectively serving demands. To demonstrate the utility of the p-DIME model, we selected Gyeongsangbuk-do in South Korea, recognized as one of the most challenging areas for providing EMS to the elderly population (aged 65 and over). This challenge arises from the significant spatial disparity in the distribution of emergency medical facilities. The results of the model assessment gauge the spatial disparity of EMS, provide significantly enhanced solutions for a more equitable EMS distribution in terms of service coverage, and offer policy implications for future EMS location planning. In addition, to address the computational challenges posed by p-DIME's inherent complexity, involving mixed-integer programming, this study introduces a solution technique through constraint formulations aimed at tightening the lower bounds of the problem's solution space. The computational results confirm the effectiveness of this approach in ensuring reliable computational performance, with significant reductions in solution times, while still producing optimal solutions.

Introduction: Obstructive sleep apnea (OSA) is the most common sleep-breathing disorder. OSA is associated with cardiovascular diseases such as coronary artery disease (CAD) and arrhythmias with an increased risk of sudden cardiac death. Some changes in ECG markers are seen as an indicator of arrhythmogenicity, especially ventricular arrhythmias. The goal of this study was to investigate if OSA patients with CAD have QT dispersion and T peak to T end (TpTe) changes as a surrogate of arrhythmogenicity. Methods: We studied 75 patients with CAD who underwent polysomnographic studies. Patients were categorized into mild, moderate, and severe OSA according to the Apnea hypopnea index (AHI). Baseline ECG and echocardiography for assessing LV function and valvular heart disease were done for all of them. Results: Results showed that in patients with moderate and severe sleep apnea QT dispersion was higher in a group with more involvement of coronary artery disease, reduced ejection fraction, and a history of old MI. However, we didn’t find any significant statistical relationship between OSA and TpTe marker. Conclusion: Our results showed a positive relation between ECG arrhythmic indices such as QT dispersion and OSA severity in patients with CAD.

Four leather substrates from different animals were treated by dispersions containing hydrophilic composite silica-hyperbranched poly(ethylene imine) xerogels. Antimicrobial activity was introduced by incorporating silver nanoparticles and /or benzalkonium chloride. The gel precursor solutions were also infused before gelation to titanium oxide powders typically employed for induction of self-cleaning properties. The dispersions from these biomimetically premade xerogels integrate environmentally friendly materials with short coating times. Scanning electron microscopy (SEM) provided information on the powder distribution onto the leathers. Substrate and coating composition were estimated by infrared spectroscopy (IR) and ener-gy-dispersive X-ray spectroscopy (EDS). Surface hydrophilicity and water permeability were assessed by water-contact angle experiments. The diffusion of the leather's initial components and xerogel additives into the water were measured by Ultraviolet-Visible (UV-Vis) spectroscopy. Protection against GRAM- bacteria was tested for Escherichia coli, Pseudomonas aeruginosa, and Klebsiella Pneumoniae against GRAM+ bacteria for Staphylococcus aureus, and Enterococcus faecalis and against fungi for Candida albicans. Antibiofilm capacity experiments were performed against Staphylococcus aureus, Klebsiella Pneumoniae, Enterococcus faecalis, and Candida albicans. The application of xerogel dispersions proved an adequate and economically feasible alternative to the direct gel formation into the substrate’s pores for the preparation of leathers intended for medical uses

Patterning, stability, and dispersion of the semiconductor quantum dots (scQDs) are the three issues strictly interconnected for successful device manufacturing. Recently several authors adopted direct optical patterning (DOP) as a step forward in photolithography to position the scQDs in a selected area. However, the chemistry behind the stability, dispersion, and patterning has to be carefully integrated to obtain a functional and therefore, commercial device. In this review are described different chemical strategies suitable to stabilize the scQDs both at a single level and as an ensemble with a special focus on the ones compatible with direct optical patterning (DOP). With the same purpose, the scQDs dispersion in a matrix was described in terms of the scQDs surface ligands interactions with the matrix itself. The chemical processes behind the DOP are illustrated and discussed for five different approaches that consider together stability, dispersion, and the patterning itself of the scQDs.

The influence of distant London dispersion forces on the docking preference of alcohols of different size between the two lone electron pairs of the carbonyl group in pinacolone is explored by infrared spectroscopy of the OH stretching fundamental in supersonic jet expansions of 1:1 solvate complexes. Experimentally, no pronounced tendency of the alcohol to switch from the methyl to the bulkier tert-butyl side with increasing size is found. In all cases, methyl docking dominates by at least a factor of two, whereas DFT-optimized structures suggest a very close balance for the larger alcohols, once corrected by CCSD(T) relative electronic energies. Together with inconsistencies when switching from a C4 to a C5 alcohol, this points at deficiencies of the investigated B3LYP and in particular TPSS functionals even after dispersion correction, which cannot be blamed on zero point energy effects. The search for density functionals which describe the harmonic frequency shift, the structural change and the energy difference between the docking isomers of larger alcohols to unsymmetric ketones in a satisfactory way is open.

Conventional mechanical Fourier Transform Spectrometers (FTS) are able to simultaneously measure absorption and dispersion spectra of gas-phase samples. However, they usually need very long measurement times to achieve time-resolved spectra with a good spectral and temporal resolution. Here, we present a mid-infrared dual-comb-based FTS in an asymmetric configuration, providing broadband absorption and dispersion spectra with a spectral resolution of 5 GHz, a temporal resolution of 20 μs, and a total measurement time of a few minutes. We used the dual-comb spectrometer to monitor the reaction dynamics of methane and ethane in an electrical plasma discharge. We observed ethane/methane formation as a recombination reaction of hydrocarbon radicals in the discharge in various static and dynamic conditions. The results demonstrate a new analytical approach for measuring fast molecular absorption and dispersion changes and monitoring fast dynamics of chemical reactions, which can be interesting for chemical kinetic research and particularly for the combustion and plasma analysis community.

Significant amounts of anthropogenic radionuclides were introduced in ocean waters following nuclear atmospheric tests and development of the nuclear industry. Dispersion of artificial dissolved radionuclides has been extensively measured for decades over the European continental shelf. The radionuclide measurement and release fluxes databases provided here represent an exceptional opportunity to validate dispersion hydrodynamic models. MARS hydrodynamic model have been applied at different scales to reproduce in realistic conditions the measured dispersion. Specific methods have been developed to obtain qualitative and quantitative results and perform model/measurement comparisons. Model validation concerns short to large scales with dedicated surveys following the dispersion: it was performed within two and three dimensions framework and from minutes and hours following a release up to several years. Results are presented concerning the dispersion of radionuclides in marine systems deduced from standalone measurements, or according to model comparisons. It allows characterising dispersion over the continental shelf, pathways, transit times, budgets and source terms. This review exhibits the main features retained from the point of view of radiotracers, hydrodynamic models and model/measurement methods with perspectives of applications in other areas or oceanographic domains.

Recent US Congressional hearings on UAPs have made the study of exotic propulsion systems a matter of serious academic study and indeed, military necessity. This speculative paper looks at the possibility that microscopic sources could produce gravitational radiation with minimal energy requirements, whilst trapping the electromagnetic radiation stress-energy from being emitted. It may be possible to form an array of these micro-emitters of sufficient strength, acting with collective phenomenon, to allow non-linearities and the formation of soliton waves suitable for a putative warp field. Interestingly we find no need for exotic matter or negative energy. Moving onto the Alcubierre metric we ponder if the field could actually be made to travel superluminally by a repetitive stepped process of, expanding space just ahead of the craft initially to speed-up the propagation of the field, via the Shapiro Delay, so that a second field propagates that contracts space aggressively; the net effect being space contracting ahead of the craft faster than light.