Interfaces between layers in 3D-printed elements produced by extrusion-based material deposition were investigated on both macro- and micro-scales. On the macro-scale, compression and bend tests were performed on two 3D-printable cement-based compositions (3PCs), namely C1 and C2. The influences of binder composition and time interval between layers on layer-interface strength were critically analyzed. In the context of additive manufacturing, the optimized composition C2, containing pozzolanic additives, exhibited mechanical performance superior to that of the mixture with Portland cement as the sole binder. In particular, Mixture C2 showed a less pronounced decrease in interface tensile strength. Even for time intervals between depositions of two layers as long as 1 day the loss in corresponding flexural strength was below 25%, as compared with C2 specimens tested in the perpendicular direction. In contrast, the decrease in flexural strength measured for C1 specimens amounted to over 90% for the same set of parameters. Higher porosity at the interfaces of the printed concrete layers was identified as the cause for the lower interface strengths of C1. Microscopic observations supported the findings of the macroscopic investigations. While a pronounced recovery (“self-healing”) of the porous, discontinuous interlayers was observed with increasing age for Mixture C2, in case of C1 the filling products grown in the porous interlayer were found to be non-strengthening.

Ti64 alloy plays a significant role in the biomedical applications such as bioimplants for its excellent biocompatibility. Its usage can be further extended by improving the surface hardness and wear resistance. In this respect, laser surface glazing (LSG), an advanced surface modification technique, is very useful which can produce thin hardened surface layer and strong metallurgical bonding. Investigation of temporal and spatial temperature distributions of laser glazed surface of materials are essential because temperature plays significant role in achieving required surface properties. Therefore, in this study, a 3D Finite element analysis has been developed to perform transient thermal analysis of LSG for Ti64 alloy. The model investigated temperature distribution, depth of modified zone and heating and cooling. The results show that the peak temperature is attained 2095 K for 300 W laser power, 0.2 mm beam width and 0.15 ms residence time. Since this temperature is above the melting point (1933 K) of Ti64 alloy, the melt depth is calculated 22.5 μm. Furthermore, from the simulation results, the average heating and cooling rates are estimated 1.19×10⁷ Ks^-1 and 2.71×10⁶ Ks^-1 respectively which indicate the presence of hard phases in the modified zone.

In tissue engineering scaffolds take the place of the natural extra cellular matrix (ECM). The natural ECM is the extracellular part of animal tissue that usually provides structural support to the animal cells in addition to performing various other important functions. The design aspect along with the choice of the material for the artificial scaffold is very crucial to cell differentiation, adhesion, proliferation, and the transport of the growth factors or other bio molecular signals. In addition to the material and design of the scaffolds, it is necessary to replicate the normal physiological situation if the scaffold has to function as an implant. The cells have to be located in the porous scaffold to form a three dimensional assembly. The article discusses the important factors to be considered while designing a scaffold for tissue engineering and regenerative medicine.

Lyme disease and associated co-infections are increasing worldwide and approximately 20% of individuals develop chronic Lyme disease (CLD)/Post-Treatment Lyme Disease Syndrome (PTLDS) despite early antibiotics. A 7–8-week protocol of double dose dapsone combination therapy (DDDCT) for CLD/PTLDS results in symptom remission in approximately 50% of patients for one year or longer, with published culture studies indicating higher doses of dapsone demonstrate efficacy against resistant biofilm forms of Borrelia burgdorferi. The purpose of this study was therefore to evaluate higher doses of dapsone in the treatment of resistant CLD/PTLDS and associated co-infections. Twenty-five patients with a history of Lyme and associated co-infections, most of whom had ongoing symptoms despite several courses of DDDCT, took one or more courses of high dose pulsed dapsone combination therapy (200 mg dapsone X 3-4 days and/or 200 mg BID x 4 days), depending on persistent symptoms. The majority of patients noticed sustained improvement in 8 major Lyme symptoms, including fatigue, pain, headaches, neuropathy, insomnia, cognition, and sweating, where dapsone dosage, not just treatment length, positively affected outcomes. High dose pulsed dapsone combination therapy may represent a novel therapeutic approach for the treatment of resistant CLD/PTLDS, and should be confirmed in randomized, controlled clinical trials.

The natural variation in estrogen secretion throughout the female menstrual cycle impacts various organs, including estrogen receptor (ER)-expressed skeletal muscle. Many women commonly experience increased fatigue or reduced energy levels in the days leading up to and during menstruation when blood estrogen levels decline. Yet, it remains unclear whether endogenous 17β-estradiol, a major estrogen component, directly affects energy metabolism in skeletal muscle due to the intricate and fluctuating nature of female hormones. In this study, we employed 3D 31P FID-MRSI to investigate phosphoryl metabolites in the soleus muscle of a cohort of young females (average age: 28 ± 6 years, n = 7) during the early follicular (EF) and peri-ovulation (PO) phases when their blood 17β-estradiol levels differ significantly (EF: 28 ± 18 pg/mL vs. PO: 71 ± 30 pg/mL, p < 0.05), while the levels of other potentially interfering hormones remain relatively invariant. Our findings reveal a reduction in ATP-referenced phosphocreatine (PCr) levels in the EF phase compared to the PO phase for all participants (5.4 ± 4.3%). Furthermore, we observe a linear correlation between muscle PCr levels and blood 17β-estradiol concentrations (r = 0.64, p = 0.014). Conversely, inorganic phosphate Pi and phospholipid metabolite GPC levels remain independent of 17β-estradiol but display a high correlation between EF and PO phases (p = 0.015 for Pi and p = 0.0008 for GPC).The robust association we have identified between ATP-referenced PCr and 17β-estradiol suggests that 17β-estradiol plays a modulatory role in the energy metabolism of skeletal muscle.

Light Detection and Ranging (LiDAR) technology, a cutting-edge advancement in mobile applications, presents a myriad of compelling use cases, including enhancing low-light photography, capturing and sharing 3D images of fascinating objects, and elevating the overall augmented reality (AR) experience. However, its widespread adoption has been hindered by the prohibitive costs and substantial power consumption associated with its implementation. To surmount these obstacles, this paper proposes a low-power, low-cost, SPAD-based system-on-chip (SoC) which packages the microlens arrays (MLA) and incorporates with a light-weight RGB-guided sparse depth imaging completion neural network for 3D LiDAR imaging. The proposed SoC integrates an 8x8 Single-Photon Avalanche Detectors (SPADs) macro pixel array with time-to-digital converters (TDC) and charge pump, fabricated using a 180nm bipolar-CMOS-DMOS (BCD) process. A random MLA-based homogenizing diffuser efficiently transforms Gaussian beams into flat-topped beams with a 45° field of view (FOV), enabling flash projection at the transmitter. To further enhance resolution and broaden application possibilities, a lightweight neural network employing RGB-guided sparse depth complementation is proposed, enabling a substantial expansion of image resolution from 8x8 to quarter video graphics array level (QVGA; 256x256). Experimental results demonstrate the effectiveness and stability of the hardware encompassing the SoC and optical system, as well as the lightweight features and accuracy of the algorithmic neural network. This integrated state-of-the-art hardware-software solution offers a promising and inspiring foundation for developing consumer-level 3D imaging applications.

Contact toxicity against Periplaneta americana has never been tested with S. collinsiae root extract. Hexane, dichloromethane, ethanol and water extracts were tested in final-instar nymphs and adult P. americana by topical application method. The dichloromethane extract showed the high-est potency of contact toxicity against the final-instar nymphs (41-100% corrected mortality at 48 hours), lowest LC50 (1.5±0.2 %w/v at 48 hours), and lowest LT50 (36.1±0.8 hours at 10%w/v) while the water crude extract lacked the contact toxicity (0-0% corrected mortality at 48 hours). Signs of toxicity, such as excited movement, trembling body, motionlessness, and swollen abdomen segment including irregularly extended foregut were found at the both stages of P. americana dropping with solutions of dichloromethane extract. Detection of didehydrostemofoline distri-bution using IMS revealed that didehydrostemofoline distributed in the tissue of the dead fi-nal-instar nymph and adult P. americana contacting with dichloromethane extract, but it was not found in tissue of euthanized P. americana which exposed to the water extract. Didehydrostemo-foline in the extract was a cause of toxicity signs and death of P. americana via a contact route. Thus, dichloromethane extract and didehydrostemofoline could be used as an active ingredient and chemical marker in aerosol and spray formulations for cockroach control.

Cardiotoxicity is an unwanted side-effect arising from different medications. The term describes a diminution of heart function, affecting especially left ventricular ejection fraction, which can progress to heart failure. Pediatric oncology patients treated with drugs of the anthracycline group, e.g., doxorubicin, can evolve to heart failure patients in adult age. Nuclear Medicine imaging of fatty acid oxidation and glycolysis accurately describes normal and altered heart metabolism. The most common finding is a state of cardiac glycolysis, which is reflected by increased uptake of 18F-desoxyglucose (18F-FDG) at a time when fatty acid oxidation is decreased. Glycolysis has recently been recognized as being the result of coenzyme Q10 deficiency as part of adaptation to hypoxia. Low LEVF correlates with impaired fatty acid oxidation. This deficiency can arise from chemotherapy and radiation and can be corrected by supplementation. Drugs like enalapril can improve fatty acid utilization. We will review relevant Nuclear Medicine imaging studies as well as fundamental biochemical data that demonstrate this pathogenetic path.

Although conventional immunohistochemistry for neurotropic Rabies virus (RABV) usually shows a high preference for neurons, non-neuronal cells are also potential target cells and abortive infection of astrocytes is considered a main trigger of innate immunity in the CNS. While in vitro studies indicated differences between field and less virulent lab-adapted RABVs, a systematic and quantitative comparison of astrocyte tropism in vivo is lacking. Here, a recently developed solvent-based tissue clearing technique was used to measure the RABV cell tropism in infected brains. Immunofluorescence analysis of 1 mm-thick tissue slices enabled 3D segmentation and quantification of infection frequencies of astrocytes and neurons. Comparison of highly virulent street virus clones from fox, dog, and raccoon with three lab strains of intermediate and low virulence revealed remarkable differences in the ability to infect astrocytes in vivo. While all viruses and infection routes led to comparable neuron infection frequencies, striking differences were detected for the infection of astrocytes. Consistent and inoculation route-independent astrocyte infection by field viruses, together with route-dependent or undetectable astrocyte infection by lab-adapted or vaccine viruses strongly suggests a model in which the ability to establish productive astrocyte infection in vivo functionally distinguishes field and attenuated lab RABV strains.

Osteoarthritis (OA) is a joint disease involving cartilage degeneration. This study aimed to compare properties of chondrocytes from less-affected (LA-Cartilage) and severely-affected (SA-Cartilage) of human OA articular cartilage. Based on Dougados classification, OA cartilage was classified into two groups; less-affected (Grade 0–1) and severely-affected (Grade 2–3). Chondrocytes from each group were cultured until passage (P) 4. Growth, migration, stem cell properties and chondrogenic properties under normal and inflammatory conditions, and the formation of in vitro 3D cartilage tissues were compared between groups. The growth and migratory properties of LA-chondrocytes and SA-chondrocytes were similar, except that the migration rate of SA-chondrocytes was significantly higher at P0 compared to LA-chondrocytes. Both LA-chondrocytes and SA-chondrocytes expressed mesenchymal stem cell markers and tri-lineage differentiation, but the expression of stem cell markers decreased significantly with increasing passage number. Exposure to inflammatory conditions induced distinct morphological changes and significant increases in expression of SOX9 at P4 and MMP3 at P1 for LA-chondrocytes. LA-chondrocytes and SA-chondrocytes able to develop into in vitro 3D constructs, but SA-chondrocytes exhibited superior cartilage-like properties. Chondrocytes from both less- and severely-affected regions are suitable to be used in clinical applications, however, chondrocytes from severely-affected regions could be a more favorable cell source.

This paper is a further development of our “Proposal of a new double-nozzle technique for in-gas-jet laser resonance ionization spectroscopy” published in journal Atoms earlier in this year. Here, we propose to equip the proposed double-nozzle technique with the RF-only funnel and RF-buncher placed in the gas-jet chamber at 70 mm distance downstream the double-nozzle exit. It allows for highly effective extraction into vacuum heavy ion beams, produced in two-steps laser resonance ionization in the argon supersonic jet. We explored the operation of this new full version of the double-nozzle technique through detailed gas dynamic and then Monte Carlo trajectory simulations, which results are presented and discussed. In particularly, we have shown by calculations that more than 80% of all nobelium-254 neutral atoms, extracted by argon flow from the gas stopping cell through the double-nozzle into the supersonic jet can be extracted into vacuum in a form of pulsed ion beam having low transverse and longitudinal emittance.s dynamic and Monte Carlo simulations

Given the concerns of waning immunity from the primary COVID-19 vaccines and the first booster dose, we conducted an on-line cross-sectional study in May 2022 to investigate willingness to receive a second COVID-19 booster dose or a new COVID-19 vaccine and its associated factors. Overall, 22.7% of participants were willing to be vaccinated, 39.3% were unsure, but tend to be willing, 25.8% were unsure, 4.9% were unsure, but tend to be unwilling, and 7.4% were unwilling to be vaccinated. The main reasons against accepting a second COVID‐19 booster dose or a new COVID-19 vaccine COVID-19 dose included concerns about the side effects, the opinion that further vaccination is unnecessary, and effectiveness uncertainties. Males, younger individuals, participants without a previous COVID-19 diagnosis, and those with good/very good self-perceived physical health were significantly more frequently willing to receive a second COVID‐19 booster dose or a new COVID-19 vaccine. Also, increased fear of the COVID-19, increased trust in COVID-19 vaccination and decreased fear of a second booster dose or a new COVID-19 vaccine were associated with increased willingness. Our results show some hesitancy and unwillingness toward further COVID-19 vaccination and indicate that fear of COVID-19 and trust in COVID-19 vaccination affect public opinion

There is a lack of data comparing sugammadex with anticholinesterase for the quality of anaesthesia recovery, especially following a single bolus dose of rocuronium. Thus, we evaluated the influence of reversal with sugammadex or neostigmine on post-operative quality of recovery by using the Post-operative Quality Recovery Scale (PQRS). A total of 86 patients undergoing trans-pars plana vitrectomy (TPPV) under general anaesthesia were intubated following a single bolus dose of rocuronium (0.6 mg/kg). At the end of surgery, patients were received either neostigmine or sugammadex. The quality of recovery was assessed using the PQRS at 15 minutes and 40 minutes after surgery, and on post-operative day 1. The recovery rate in the physiological domain was higher in the sugammadex group at 15 minutes after surgery (P = 0.02). Though there were no significant differences in the overall cognitive recovery domain, patients in the sugammadex group could recall more numbers in reverse order. However, there were no significant differences between the groups in the other domains of the PQRS. The use of sugammadex may increase the quality of the post-operative physiological recovery at early post-operative periods compared with neostigmine use following a single bolus dose of rocuronium in patients undergoing TPPV with general anaesthesia.

(1) Background: This paper illustrates an innovative methodological approach chosen to study and map the colors of the Medieval wall painting of Santa Maria Antiqua in the Roman forum, one of the pilot sites of the EHEM project (Enhancement of Heritage Experiences: The Middle Ages. Digital Layered Models of Architecture and Mural Paintings over Time); (2) Methods: We chose to use two methods for gathering information about colors and mapping, specifically colorimetry by spot measurements and hypercolorimetric multispectral imaging (HMI) to map those same colors sampled through colorimetry; (3) Results: Chromatic data of all colors in the wall paintings were obtained in the CIELAB color space. In those same points, chromatic similarity maps were performed by the innovative HMI system, a multispectral imaging technique able to obtain also color data information by means of the advanced calibration software named SpectraPick®: this allowed to have a complete knowledge of the color characteristics and distribution; (4) Conclusion: The color measurements and mapping was an important result to improve the reading of Medieval wall paintings, fragmentary and stratigraphically complex, giving a new light in the knowledge of the colors and allowing to better understand the original appearance of the iconographic patterns, reconstructed with colors as faithfully as possible similar to the originals.

The purpose of the study was to identify factors characterizing a decrease in LV global systolic function in patients with ST-segment elevation myocardial infarction (STEMI) after revascularization using cardiac magnetic resonance imaging (MRI)-based ischemic injury pattern and laboratory parameters sensu left ventricular global systolic function. A total of 109 STEMI patients were examined. The patients underwent contrast-enhanced cardiac MRI with a 1.5 Tesla GE SIGNA Voyager (GE HealthCare, USA) on the 7th-10th days from the onset of the disease. According to cardiac MRI analysis, the patients were divided into the following groups with regard to left ventricular ejection fraction (LVEF) values: group 1 – patients with LVEF ≥50%; group 2 – patients with mildly reduced LVEF 40-49%; group 3 – patients with low LVEF <40%. A predominance of most parameters of the ischemic injury pattern was noted in patients with mildly reduced and low LVEF versus patient group with LVEF ≥50%. Some risk factors for a decrease in LVEF <50% systolic function in STEMI patients after revascularization were revealed: male gender; time from the onset of the anginal attack to revascularization; coronary artery status; several LV parameters; ischemic injury characteristics; natriuretic peptide and troponin I levels.

Abstract: Accurately predicting a fetus's gestational age (GA) is of utmost importance in prenatal care. This study aimed to develop an artificial intelligence (AI) model that can automatically predict GA using biometric measurements derived from fetal brain mag-netic resonance imaging (MRI). Additionally, we aimed to assess the significance of con-sidering different references when interpreting GA predictions. To achieve this, we obtained measurements such as Biparietal Diameter (BPD), Fron-to-occipital Diameter (FOD), and Head Circumference (HC) from a dataset comprising 52 normal fetal MRI cases with T2 Haste sequences from Rush University. Both manual and AI-based methods were utilized to acquire these measurements. We also employed three reference papers (Garel, Freq, and Bio) for comparison purposes. The results demonstrated a strong correlation between manual and AI measure-ments, indicating consistency between the two methods. The AI-based measurement of HC exhibited a higher correlation with actual values compared to BPD, FOD, and correct-ed BPD (BPDC). When comparing these measurements with GA in the Picture Archiving and Communication System (PACS), the differences varied depending on the reference used. Specifically, the differences ranged from 0.47 to 2.17 weeks for BPD, 0.46 to 2.26 weeks for FOD, and 0.75 to 1.74 weeks for HC. Furthermore, the Pearson correlation coeffi-cient analysis revealed that all correlation coefficients between PACS records and GA pre-dictions using different references were greater than 0.97. In conclusion, the AI model based on fetal brain MRI accurately predicts GA by uti-lizing BPD, FOD, and HC measurements. The AI approach, which involves combining line segments to calculate fetal head circumference, offers improved accuracy and con-venience compared to manual estimation. This study underscores the potential of AI models in accurately estimating gestational age and highlights their utility in prenatal care. By integrating AI as a valuable tool in prenatal care, we can enhance the accuracy, ef-ficiency, and decision-making involved in assessing fetal development and monitoring pregnancies using MRI measurements.

Sea ice roughness can serve as a proxy for other sea ice characteristics such as ice thickness and ice age. Arctic-wide maps that represent spatial patterns of sea ice roughness can be used to better characterize spatial patterns of ice convergence and divergence processes. Sea ice surface roughness can also control and quantify turbulent exchange between sea ice surface and atmosphere and therefore influence surface energy balance at the basin scale. We have developed a data processing system that produces georeferenced sea ice roughness rasters that can be mosaicked to produce Arctic-wide maps of sea ice roughness. This approach starts with Top-of-Atmosphere radiance data from the Multi-angle Imaging SpectroRadiometer (MISR). We used red-band angular data from three MISR cameras (Ca, Cf, An). We created a training data set in which MISR pixels were matched with co-located and concurrent lidar-derived roughness measurements from the Airborne Topographic Mapper (ATM). We used a K-nearest neighbor algorithm with the training data to calibrate the multi-angle data to values of surface roughness and then applied the algorithm to Arctic-wide MISR data for two 16-day periods in April (spring) and July (summer). After georeferencing the roughness rasters, we then mosaicked each 16-day roughness dataset to produce Arctic-wide maps of sea ice roughness for spring and summer. Assessment of the results shows good agreement with independent ATM roughness data, not used in model development. A preliminary exploration of spatial and seasonal changes in sea ice roughness for two locations shows the ability to characterize the roughness of different ice types and the results align with previous studies. This processing system and its data products can help the sea ice research community to gain insights into the seasonal and interannual changes in sea ice roughness over the Arctic.

In this study, lithium reaction distributions, dependent on charge-discharge rate, were nondestructively visualized for a commercial lithium-ion battery, using the Compton scattering imaging technique. By comparing lithium reaction distributions obtained from two different charge-discharge speeds, residual lithium ions were detected at the center of the negative electrode on a fully discharged state, by relatively high-speed discharge rate. Moreover, we confirmed that inhomogeneous reactions were facilitated on a relatively high-speed charge-discharge rate, in both the negative and positive electrodes. A feature of our technique is that it can be applied to commercially used lithium-ion batteries, because it uses high-energy X-rays with a high penetration power. Our technique thus opens a novel analyzing pathway for developing advanced batteries.

Abstract Sodium glucose cotransporter type 2 inhibitors are a new class of drugs acting on cardiovascular system, renal and metabolism in a multiple way. Indeed, even their principal action is on the transporter of sodium and glucose in the convoluted distal tubule, they have multiple actions as antifibrotic and endothelial protective action. Their principal mechanism consist in the loss of sodium and glucose. Therefore, they have effect on blood pressure and glucose metabolism. In a first period their use has been in the diabetic general population, later on some studies documented their activity in non-diabetic general population, in heart failure in chronic kidney disease. Only in recent years several small studies documented their efficacy in diabetic and non-diabetic kidney transplant patients, larger studies are few and very recent and open new ways for these drugs

Most common classifications for acetabular bone defects are based on radiographic two-dimension imaging, with low reliability and reproducibility. With the rise of modern processing techniques based on 3D modelling, methodologies for volumetric quantification of acetabular bone loss are available. Our study aims to describe a new methodology for quantitative assess-ment of acetabular defects, based on 3D modelling, focused on the surface analysis of the integrity of the main anatomical structures of the acetabulum represented by four corresponding sectors (posterior, superior, anterior, and medial). The defect entity is measured as the Area Increase Ra-tio (AIR) detected in all the sectors analyzed on three planes of view (frontal, sagittal and axial) compared to healthy hemipelvises. The analysis was performed on 3D-models from the CT-scan of six exemplary specimens with a unilateral pathological hemipelvis. AIR between the native and the pathological hemipelvis was calculated for each sector, for a total of 48 analysis (range, +0.93% - +171.35%). AIR of >50% were found in 22/48(45.8%) sectors and affected mostly the posterior, medial and superior sectors (20/22, 90.9%). Qualitative analysis showed consistency of the data with the morphological features of the defects. Further studies with larger samples are needed to validate the methodology and potentially develop a new classification scheme.

Two pre-pulses focused at different positions and at different time moments were used to enhance THz emission generated by the main pulse. The emission of THz radiation from air breakdown regions of focused ultrashort fs-laser pulses (800 nm/35 fs) at shockwave front prepared by pre-pulses was investigated, and a 3D spatio-temporal control was established for the most intense emission. The laser pulse-induced air breakdown forms a ~120 micrometers-long focal volume and generates a shockwave that delivers denser air into the focal region of the main pulse for enhanced generation of THz radiation at 0.1-2.5 THz spectral window. The intensity of pre- and main-pulses was at the tunneling ionisation intensities (1-3)x10¹⁶ W/cm² and corresponded to sub-critical (transparent) plasma in air. Polarisation analysis revealed that the orientation of the air density gradients generated by pre-pulses and their time-space placement defined the ellipticity of the generated THz electrical field. The rotational electric current is the origin of THz radiation. The current is created by non-parallel gradients of electron density and temperature. Scaling dependencies of THz emission control are established.

This study reports the development of a numerical method to simulate two-phase flows of Newtonian fluids that are incompressible, immiscible, and isothermal. The interface in the simulation was located and reconstructed using the geometric volume of fluid (VOF) method. The implementation of the Piecewise-Linear Interface Calculation (PLIC) scheme of the VOF method was performed to solve the three-dimensional (3D) interface transport during the dynamics of two-phase flows. In this method, the interface is approximated by a line segment in each interfacial cell. The balance of forces at the interface was accounted for using the continuum interfacial force (CSF) model. To solve the Navier-Stokes equations, meshless finite difference schemes from the HiG-Flow computational fluid dynamics software were employed. The 3D PLIC-VOF HiG-Flow algorithm was used to simulate several benchmark two-phase flows for the purpose of validating the numerical implementation. First, the performance of the PLIC implementation was evaluated by conducting two standard advection numerical tests: the 3D shearing flow test and the 3D deforming field test. Good agreement is obtained for the 3D interface shape using both the 3D PLIC-VOF HiG-Flow algorithm and those found on the scientific literature. In addition, the absolute error of the volume tracking advection calculation obtained by our 3D PLIC-VOF HiG-Flow algorithm was found to be smaller than the one found in the scientific literature for both the 3D shearing and 3D deforming flow tests. Lastly, the 3D bubble rising problem was simulated for different fluid densities and viscosity’s ratios. Again, good agreement is obtained for the 3D interface shape using both the newly implemented algorithm and the OpenFOAM, DROPS and NaSt3D software. The bubble’s rise velocity and evolution of the bubble’s center of mass is also computed with the 3D PLIC-VOF HiG-Flow algorithm and found to be in agreement with these software.

A novel approach for the long-term medical treatment of the inner ear is the diffusion of drugs through the round window membrane from a patient-individualized, drug-eluting implant, which is inserted in the middle ear. In this study, drug-loaded (10 wt% Dexamethasone) guinea pig round window niche implants (GP-RNIs, ~1.30 mm x 0.95 mm x 0.60 mm) were manufactured with high precision via micro injection molding (µIM, Tmold = 160 °C, crosslinking time of 120 s). The medical grade silicone elastomer MED-4244 (NuSil Technology LLC, Radnor, PA, USA) was used. Molds for µIM were 3D printed from a commercially available resin PlasGRAY V2 (Asiga, Alexandria, Australia, TG = 84 °C) via a high-resolution DLP process (xy-resolution of 32 µm, z-resolution of 10 µm, 3D printing time of about 6 h). Drug release, biocompatibility, and bio-efficacy of the GP-RNIs were investigated in vitro. GP-RNIs could be successfully produced. Wear of the molds due to thermal stress was observed. However, the molds are suitable for single use in the µIM process. About 10% of the drug load (8.2 ± 0.6 µg) was released after 6 weeks (medium: isotonic saline). The implants showed high biocompatibility over a time of 28 days (lowest cell viability ~80%). Moreover, we found anti-inflammatory effects over a time of 28 days in a TNF-α-reduction test. These results are promising for the development of long-term drug-releasing implants for human inner ear therapy.

Aim of this research paper is to introduce a novel method of hybrid orthodontic tooth-borne distalizer treatment of class II malocclusion by using 3D printed biocompatible personalized distalizer. Explains 3D designing, printing and clinical application of individualized biocompatible medical device dedicated for orthodontic teeth distalization. Compares such distalizer manufactured from two different biocompatible photopolymers (white and transparent). Evaluates their clinical performance and also patients’ aesthetical perception. Clinical part includes comparison of treatment debonding on the set of 12 complete orthodontic treatments with uni-lateral class II malocclusion managed with hybrid approach (CAT-Invisalign with 3D printed distalizer). Paper offers an evaluation of the personalized distalizer functioning in regard to current publications and comparison to conventional prefabricated alternatives like Carriere® Distalizer™ appliance. Results showed no significance of material differences on clinical performance of such individualized distalizers. Research showed preference of patients towards transparent biocompatible photopolymer instead of white A2 shade.

Pure orbital blowout fractures occur within the confines of the internal orbital wall. Restoration of orbital form and volume is paramount to prevent functional and esthetic impairment. The anatomical peculiarity of the orbit has encouraged surgeons to develop implants with customized features to restore its architecture. This has resulted in worldwide clinical demand for patient-specific implants (PSIs) designed to fit precisely in the patient's unique anatomy. Fused filament fabrication (FFF) three-dimensional (3D) printing technology has enabled the fabrication of implant-grade polymers such as Polyetheretherketone (PEEK), paving the way for a more sophisticated generation of biomaterials. This study evaluates the FFF 3D printed PEEK orbital mesh customized implants with a metric considering the relevant design, biomechanical, and morphological parameters. The performance of the implants is studied as a function of varying thicknesses and porous design constructs through a finite element (FE) based computational model and a decision matrix based statistical approach. The maximum stress values achieved in our results predict the high durability of the implants, and the maximum deformation values were under one-tenth of a millimeter (mm) domain in all the implant profile configurations. The circular patterned implant (0.9 mm) had the best performance score. The study demonstrates that compounding multi-design computational analysis with 3D printing can be beneficial for the optimal restoration of the orbital floor.

Marketing is one of the important stages, the decisive factor affecting the success of production and business activities of every business. Therefore, marketing is considered to be the first and most important stage in the process of introducing, bringing products to market and branding of businesses, especially in the period when the disease situation is taking place very complicated worldwide. This study provides both qualitative and quantitative results for the following research objectives. Firstly, the study will assess the situation and analyze the appropriateness of marketing models in the current market situation trend. Secondly, the study proposes an approach in building a new type of marketing model, which is 3D web-based marketing applied in e-commerce to support the modeling of enterprise products in the form of Interactive 3D products are similar to real products. Thirdly, testing and evaluating 3D e-commerce web marketing model at Truong Hai Auto Showroom, Thai Nguyen City branch. This study also proposes a number of solutions for the research and deployment of 3D web marketing model application for businesses in the current market situation.

Microfluidics is facing critical challenges in the quest of miniaturizing, integrating, and automating in vitro diagnostics, including the increasing complexity of assays, the gap between the macroscale world and the microscale devices, and the diverse throughput demands in various clinical settings. Here a “3D extensible” microfluidic design paradigm that consists of a set of basic structures and unit operations was developed for constructing any application-specific assay. Four basic structures- check valve (in), check valve (out), double-check valve (in and out), and on-off valve, were designed to mimic basic acts in biochemical assays. By combining these structures linearly, a series of unit operations can be readily formed. We then proposed a “3D extensible” architecture to fulfill the needs of the function integration, the adaptive “world-to-chip” interface, and the adjustable throughput in the X, Y, and Z directions, respectively. To verify this design paradigm, we developed a fully integrated loop-mediated isothermal amplification microsystem that can directly accept swab samples and detect Chlamydia trachomatis automatically with a sensitivity one order higher than that of the conventional kit. This demonstration validated the feasibility of using this paradigm to develop integrated and automated microsystems in a less risky and more consistent manner.

Designing motion representations for the problem of 3D human action recognition from skeleton sequences is an important yet challenging task. An effective representation should be robust to noise, invariant to viewpoint changes and result in a good performance with low-computational demand. Two main challenges in this task include how to efficiently represent spatio-temporal patterns of skeletal movements and how to learn their discriminative features for classification task. This paper presents a novel skeleton-based representation and a deep learning framework for 3D action recognition using RGB-D sensors. We propose to build an action map called SPMF (Skeleton Posture-Motion Feature), which is a compact image representation built from skeleton poses and their motions. An Adaptive Histogram Equalization (AHE) algorithm is then applied on the SPMF to enhance their local patterns and form an enhanced action map, namely Enhanced-SPMF. For learning and classification tasks, we exploit Deep Convolutional Neural Networks based on the DenseNet architecture to learn directly an end-to-end mapping between input skeleton sequences and their action labels via the Enhanced-SPMFs. The proposed method is evaluated on four challenging benchmark datasets, including both individual actions, interactions, multiview and large-scale datasets. The experimental results demonstrate that the proposed method outperforms previous state-of-the-art approaches on all benchmark tasks, whilst requiring low computational time for training and inference.

This work investigates how the user-controlled parameters of the 3D printing process define temperature conditions on the boundary between layers of the part being fabricated and how these conditions influence the structure and strength of the part. The process studied is fused filament fabrication with a desktop 3D printer and the material utilized is PLA (polylactic acid). As a characteristic of the part strength the fracture load in the case of a three-point bend and calculated related stress were used. During the printing process parts were oriented with the long side along the Z axis, thus, in the bend tests, the maximum stress occurred orthogonally to the layers. During the fabrication process, temperature distribution on the sample surface was monitored with thermal imager. Sample mesostructure was analyzed using SEM. The influence of the extrusion temperature, the intensity of part cooling, the printing speed and the time between printing individual layers were considered. The influence of all the parameters can be expressed through two generalizing factors: the temperature of the previous layer and the flow efficiency, determining the ratio of the amount of extruded plastic to the calculated. A regression model was proposed that describes the effect of the two factors on the printed part strength. Along with interlayer bonding strength, these two factors determine the formation of the part mesostructure (the geometry of the boundaries between individual threads). It is shown that the optimization of the process parameters responsible for temperature conditions makes it possible to approximate the strength of the interlayer cohesion to the bulk material strength.

Acoustic Radiation Forced Impulse (ARFI) is an ultrasound integrated method, measuring stiff-ness by point shear wave elastography. To evaluate the diagnostic performance of ARFI of the liver and of the spleen, combined with spleen dimension and platelet count, in predicting clinical events in cirrhosis, a prospective and cross-sectional study was conducted between February 2017 and February 2021. The following ratio scores with ARFI measurements were performed: ALSDP (ARFI Liver-Spleen Diameter-to-Platelets ratio score), ASSDP (ARFI Spleen-Spleen Diam-eter-to-Platelets ratio score), ASSAP (ARFI Spleen-Spleen Area-to-Platelets ratio score), ALSAP (ARFI Liver-Spleen Area-to-Platelets ratio score). In 100 enrolled subjects, spleen ARFI, ASSDP, ASSAP, were significantly associated with high-risk oesophageal varices (HRVs) in the prospec-tive short- and long-term follow-up and in the cross-sectional study (p 0.7). ARFI-ratio scores can predict, in cirrhotic patients, the risk of developing HVRs in short and long-term period.

Background: Oxytocin is recommended as the first-line choice for labor induction in term pregnant women with premature rupture of membranes (PROM); however, it can occasionally lead to failed induction and delivery complications. The primary objective of this study was to compare delivery information and outcomes following the administration of oxytocin infusion or oral low-dose misoprostol solution for labor induction in term PROM women with an unfavorable cervical condition. Methods: A prospective nested case-control study was conducted at a tertiary general hospital in China from March 2020 to February 2024, comparing oxytocin infusion and oral administration of 25ug misoprostol every 2 hours for labor induction in term PROM women with a Bishop score

Management of inflammatory bowel disease (IBD) often relies on biological and immunomodulatory agents for remission through immunosuppression, raising concerns regarding the SARS-CoV-2 vaccine's effectiveness. The emergent variants have hindered the vaccine neutralization capacity, and whether the third vaccine dose has the capacity to neutralize SARS-CoV-2 variants in this population remains unknown. This study aims to evaluate the humoral response of SARS-CoV-2 variants in patients with IBD 60 days after the third vaccine dose [BNT162b2 (Pfizer-BioNTech) or mRNA-1273 (Moderna)].56 su bjects with IBD and 12 healthy subjects were recruited. 90% of patients with IBD (49/56) were receiving biologics and/or immunomodulatory therapy. 24 subjects with IBD did not develop effective neutralizing capability against the Omicron variant. 70% (17/24) of those subjects were receiving anti-Tumor Necrosis Factor therapy [10= adalimumab, 7= infliximab], two of them had a history of COVID-19 infection, and one subject did not develop immune neutralization against three other variants: Gamma, Epsilon, and Kappa. All subjects in the control group developed detectable antibodies and effective neutralization against all seven SARS-CoV-2 variants. Our study shows that patients with IBD might not be protected against SARS-CoV-2 variants, and larger studies are needed to evaluate optimal immunity.

An association between subtle changes in T2 white matter hyper-intense signals (WMHS) de-tected in fetal brain magnetic resonance imaging (fbMRI) and congenital cytomegalovirus (CMV) infection has been established. The research aim of this study is to compare children with congenital CMV infection with neurodevelopment outcome and hearing deficit with and with-out WMHS in a prospective historic cohort of 58 fbMRIs. Of these, WMHS was detected in 21. The median infection week of the WMHS group was earlier than the normal fbMRI group (8 and 17 weeks of gestation respectively). The proportion of infants treated with valganciclovir in the WMHS group was distinctly higher. Hearing impairment was not significantly different be-tween the groups. VABS scores in all 4 domains were within normal range in both groups. The median score of the motor skills corrected for week of infection was better in the WMHS group. A multivariate analysis using week of infection interaction variable of WMHS and valganciclo-vir treatment showed better motor score outcomes in the valganciclovir treatment group despite earlier week of infection. WMHS was not associated with neurodevelopmental outcome and hearing deficit. In our cohort valganciclovir treatment may have a protective effect on fetuses with WMHS by improving neurodevelopment outcome.

Chemotherapy for lung cancer has made remarkable progress, and its selection has been subdivided by genetic analysis. Although response evaluation criteria in solid tumors (RECIST) is a simple and highly objective evaluation method, it has been pointed out that it has the disadvantage of not being able to accurately evaluate the therapeutic effect of molecularly targeted drugs and immune checkpoint inhibitors. The purpose of this study is to determine whether quantitative evaluation of DWIBS is useful in determining the effectiveness of treatment for lung cancer. There were 31 patients with lung cancer and 56 patterns were obtained. First, the determination of treatment effect (PD, SD, PR) based on RECIST was performed on CT. Second, tDV and ADC (median) were measured using BD score from DWI images taken at the same time, and the rate of change was calculated. Then, we compared and examined the correlation between RECIST and the rate of change in tDV. There were correlations between RECIST and the rate of change in tDV in PD and PR cases respectively. Compared RECIST on CT, DWIBS using BD score would be more accurate for response evaluation of treatment. There was a tendency that tDV decreased with increasing ADC values, but some of the cases had a dissociated response with increasing ADC values and increasing tDV. Thus, since the color display of ADC values allows us to infer their contents, it would be useful for the evaluation of cases such as dissociated response and pseudoprogression, which are suspected to be atypical responses that are difficult to evaluate with RECIST and other methods.

This study aimed to identify the utility of diffusion-weighted magnetic resonance (MR) imaging with an apparent diffusion coefficient (ADC) map as a predictor of the intrahepatic response of hepatocellular carcinoma (HCC) to cisplatin-based hepatic arterial infusion chemotherapy (HAIC). We retrospectively evaluated 113 consecutive patients with HCC who underwent gadoxetic acid-enhanced and diffusion-weighted MR imaging. The appropriate cutoff for the tumor-to-liver ADC ratio was determined to be 0.741. Of the 113 patients, 51 (45%) presented with a tumor-to-liver ADC ratio < 0.741. Evaluation of the intrahepatic treatment response after 2-3 cycles of HAIC in these 51 patients revealed that 20 patients (39%) experienced an objective response to HAIC. On the other hand, only 10 of the 62 patients with a tumor-to-liver ADC ratio ≥ 0.741 (16%) experienced an objective response. Thus, the objective response rate was significantly higher in patients with a tumor-to-liver ADC ratio < 0.741 than in those with a tumor-to-liver ADC ratio ≥ 0.741 (P = 0.006). Multivariate logistic regression analysis using parameters including perfusion alteration, percentage of a non-enhancing portion, and tumor-to-liver ADC ratio revealed that a tumor-to-liver ADC ratio < 0.741 (odds ratio 3.03; P = 0.015) is the sole predictor of an objective response to HAIC. Overall survival rates were significantly higher in patients with objective responses to HAIC than in those without objective responses (P = 0.001 by log-rank test). In conclusion, patients with unresectable HCC with a tumor-to-liver ADC ratio < 0.741 showed a favorable intrahepatic response to HAIC. Therefore, diffusion-weighted MR imaging can play a critical role as a predictor of response to cisplatin-based HAIC in unresectable HCC.

In this article, we introduce a new approach to human movement by defining the movement as a static object or a super object in one two-dimensional image. This method can allow researchers to label and describe the total movement as an object isolated from a reference video. This ap-proach allows us to perform various tasks, including finding similar movements in a video, measuring, and comparing movements, generating new similar movements, and defining chore-ography by controlling specific parameters in the human body skeleton. As a result of the pre-sented approach, we can eliminate the need to label images manually, disregard the problem of finding the beginning and the end of a movement, overcome synchronization issues between movements, and perform any deep learning network-based operation that processes super objects in images in general. As part of this article, we will demonstrate two application use cases: one il-lustrates how to verify and score a requested movement. In contrast, the other illustrates how to generate similar movements in the human skeleton space by addressing the challenge of supply-ing sufficient training data for deep learning applications (DL). A Variational Auto Encoder (VAE) simulator and an EfficientNet-B7 classifier architecture embedded within a Siamese twin neural network are presented in this paper in order to demonstrate two use cases. These use cases demonstrated the versatility of our innovative concept in measuring, categorizing, inferring hu-man behavior, and generating gestures for other researchers.

This article explores the potential of the Unreal Engine game engine as a tool for creating highly realistic 3D visualizations of GIS data, specifically in the context of significant historical areas. The research will focus on the computational techniques used in the 3D visualization of GIS data and the Unreal Engine software and its potential applications in geomatics. The article also presents several relevant scientific studies and projects that have successfully used game engines for similar purposes, explores the potential for using GIS data within a game engine, including plug-ins that provide additional functionality to GIS software, and the use of procedural modeling to create 3D objects through the CityEngine software plug-in. Finally, the research is applied to a dataset of the historical Vltava Valley covering an area of 1670 km2 to demonstrate the capabilities of Unreal Engine in creating realistic visualizations of large historical landscapes, and the resulting visualizations are presented. This practical application of the research provides valuable insights into the potential of the Unreal Engine as a powerful tool for creating highly realistic 3D visualizations of large historical areas with potential applications in the field of geomatics.

Novolac phenol-formaldehyde resins have gained extensive commercial utilization across diverse applications due to their exceptional mechanical, thermal, and chemical resistance properties. In this investigation, we successfully synthesized a traditional novolac, and a biobased novolac phenol-formaldehyde resin by partially substituting phenol with a bio-oil obtained from the organic phase resulting from the fast pyrolysis of pinewood biomass. Despite extensive investigations into the curing behavior of novolac resins crosslinked with hexamethylenetetramine (HMTA) through numerous model-fitting cure kinetic studies, a comprehensive model for predicting the crosslinking of bio-based phenol-formaldehyde resins in the presence of HMTA has not yet been studied. The primary objective of this research was to compare and apply several commonly used kinetic models to predict the degree of curing and cure rate of the synthesized resins, using DSC dynamic measurements. Our results demonstrated that the autocatalytic model exhibited excellent fitting for the traditional novolac resin and HMTA mixture, while the Kamal model showed better fitting with the experimental data obtained for the bio-based phenol-formaldehyde resin and HMTA system. In addition, the results evidenced a significant drop in the curing temperature by partially replacing phenol with bio-oil. Additionally, the results revealed a notable reduction in curing temperature when phenol was partially substituted with bio-oil. This substitution not only offers environmental benefits but also promotes energy efficiency and enhances production safety. The data collected in this study is pivotal for our subsequent research endeavors, which aim to develop environmentally sustainable materials optimized for use in 3D printing manufacturing processes.

This research discusses the development of a software-centered EdTech (Education Technology) class model through the implementation of a course titled "3D Time Machine" at a 4-year university in Republic of Korea over two semesters. The course focused on teaching 3D modeling software, Blender, within the history department. The primary objective of offering this course was to equip students from the digital generation with the capability to manipulate digital technology effectively. Through studying historical materials and accumulating domain knowledge, students could construct their narratives from their unique perspectives. This aimed to foster their proficiency in digital technology operation, preparing them for an education environment increasingly centered around virtual worlds. As the use of virtual worlds gains prominence in educational settings, there is a growing need to incorporate curricula that prepare students to thrive as well-prepared citizens in future societies. Assessing the digital competencies of contemporary university students and designing instructional models with particular attention to their needs is becoming increasingly important. This research draws insights from interviews, conducted in both face-to-face and written formats, with students who participated in the "3D Time Machine" course. The interviews revealed valuable insights that can be actively incorporated into the development of software-centered EdTech instructional models. They reported that they expanded their perceptions as they learned how to make their ideas tangible. The course helped students overcome their fear of digital technology. In conclusion, the course effectively employs 3D modeling technology, a software-centered EdTech, as a core element in helping students develop their narratives rapidly and diversely, thereby playing a crucial role in their ability to articulate their unique perspectives.

Increasing the availability of alternative protein from insects is important to solving food shortages. Not only are insects a rich source of protein, the use of insect ingredi-ents can reduce food waste. Insects are thus a potentially valuable ingredient for food industries and even food eaten on deep-space missions. The three-dimensional produc-tion of food on space missions has gained attention owing to its potential to reduce au-tonomous food production and produce sustainable food for long-duration space mis-sions. This study investigated the printability and rheological properties of a high-protein food system derived from mealworms and guar gum used as a stabilizer to im-prove printability. Stability and rheological properties were analyzed for various print-ing parameters. The results indicate that as the guar gum concentration was increased from 0 to 1.75%, the yield stress of the mealworm paste increased from 39 to 1096 Pa. Increasing the guar gum concentration thus resulted in a mealworm paste that was more viscous, exhibited shear thinning behavior, could support itself and was thus more stable. In summary, introducing guar gum resulted in a mealworm paste with rheological properties more suitable for printing in terms of printability and stability.

In this study, we designed a functional neuro-cardiac model to help us examine the role of neuronal regulation and confirm the importance of neural innervation techniques for cardiac tissue regeneration. A three-dimensional (3D) bioprinted neuro-cardiac scaffold composed of a mixture of gelatin-alginate and alginate-genipin-fibrin hydrogels was developed with a 2:1 ratio of AC16 cardiomyocytes (CMs) and retinoic acid differentiated SH-SY5Y neuronal cells (NCs) respectively. A unique semi-3D bioprinting approach was adopted where the CMs were mixed in the cardiac bioink and printed using an anisotropic accordion design to mimic the physiological tissue architecture in vivo. The voids in this 3D structure were methodically filled in using a NCs-gel mixture and cross-linked. Confocal fluorescent imaging using Microtubule-associated protein 2 (MAP-2) antibodies for labeling NCs, and the MyoD1 antibody for CMs revealed functional coupling between the two cell types in the final cross-linked structure. This data confirmed the development of a physiologically functional neuro-cardiac model that can be used to study neuro-cardiac modulation under physiological and pathological conditions.

A chairside polishing kit is an alternative to a laboratory polishing technique. This study aimed to evaluate the effects of different polishing techniques on the surface roughness of three-dimensional (3D)-printed acrylic denture bases (ADB). One hundred twenty disc-shaped specimens were fabricated from one conventional heat-polymerized (HP) ADB resin and two 3D-printed (Asiga (AS) and NextDent (ND)) ADB resins (n=40 per ADB resin). Each group was furtherly divided based on the polishing protocol (n=10) as follows: convectional polishing protocol (C), Microdont chairside polishing kit (M), Shofu chairside polishing kit (S), and unpolished group (U). The surface roughness (surface roughness average (Ra) and average maximum profile height (Rz)) of the printed specimens were measured using an optical profilometer, and the scanning electron microscope (SEM) was used to capture the surface at ×1000. Two-way ANOVA and post hoc tests were used for data analysis (α = 0.05) at significant levels. In unpolished groups, there was a statically significant difference between HP vs 3D-printed ADBs (p &lt; 0.0001). For Ra values, the lowest values were presented in HP-C, AS-S, and ND-C. While the highest values were shown in all unpolished groups. Within the material, there were statistically significant differences between the three polishing protocols (C, M, and S) vs unpolished (p &lt; 0.0001), while there was no significant between C, M, and S groups (p = 0.05). The Rz values had the same pattern as the Ra values. The two chairside polishing kits were comparable to conventional polishing technique, and it could be recommended for the clinical application.

This paper is part of a study of earthen mixtures for 3D printing of buildings. To meet the ever-growing environmental needs, the focus of the paper is on a particular type of biocomposite for the stabilization of earthen mixtures—the rice husk-lime biocomposite—and on how to enhance its effect on the long-term mechanical properties of the hardened product. Having assumed that the shredding of the vegetable fiber is precisely one of the possible ways to improve the mechanical properties, we compared the results of uniaxial compression tests performed on cubic specimens made with both shredded and unaltered vegetable fiber, for three curing periods. The results showed that the hardened earthen mixture is not a brittle material in the strict sense, because it exhibits some peculiar behaviors, anomalous for a brittle material. However, being a “designable” material, its properties can be varied with a certain flexibility to get as close as possible to the desired ones. One of the peculiar properties of the hardened earthen mixture deserves further investigation, rather than corrections. This is the vulcanization that occurs (in a completely natural way) in the long term, thanks to the mineralization of the vegetable fiber by carbonation of the lime.

We calculate the parameters of the Ginzburg–Landau (GL) equation of a three-dimensional attractive Fermi gas around the superfluid critical temperature. We compare different levels of approximation throughout the Bardeen–Cooper–Schrieffer (BCS) to the Bose–Einstein Condensate (BEC) regime. We show that the inclusion of Gaussian fluctuations strongly modifies the values of the Ginzburg–Landau parameters approaching the BEC regime of the crossover. We investigate the reliability of the Ginzburg–Landau theory, with fluctuations, studying the behavior of the coherence length and of the critical rotational frequencies throughout the BCS-BEC crossover. The effect of the Gaussian fluctuations gives qualitative correct trends of the considered physical quantities from the BCS regime up to the unitary limit of the BCS-BEC crossover. Approaching the BEC regime, the Ginzburg–Landau equation with the inclusion of Gaussian fluctuations turns out to be unreliable.

A method for generating fluoroscopic (time-varying) volumetric images using patient-specific motion models derived from 4-dimensional cone-beam CT (4D-CBCT) images is developed. 4D-CBCT images acquired immediately prior to treatment have the potential to accurately represent patient anatomy and respiration during treatment. Fluoroscopic 3D image estimation is done in two steps: 1) deriving motion models and 2) optimization. To derive motion models, every phase in a 4D-CBCT set is registered to a reference phase chosen from the same set using deformable image registration (DIR). Principal components analysis (PCA) is used to reduce the dimensionality of the displacement vector fields (DVFs) resulting from DIR into a few vectors representing organ motion found in the DVFs. The PCA motion models are optimized iteratively by comparing a cone-beam CT (CBCT) projection to a simulated projection computed from both the motion model and a reference 4D-CBCT phase, resulting in a sequence of fluoroscopic 3D images. Patient datasets were used to evaluate the method by estimating the tumor location in the generated images compared to manually defined ground truth positions. Experimental results showed that the average tumor mean absolute error (MAE) along the superior-inferior (SI) direction and the 95th percentile in two patient datasets were (2.29 mm and 5.79 mm) for patient 1 and (1.89 mm and 4.82 mm) for patient 2. This study has demonstrated the feasibility of deriving 4D-CBCT-based PCA motion models that have the potential to account for the 3D non-rigid patient motion and localize tumors and other patient anatomical structures on the day of treatment.

The paper formulates requirements for a polymer material for molding products from it by fused deposition modeling. A methodology for evaluating the suitability of a polymer or composite of thereof in 3D printing technology has been developed. A graphic representation of the developed methodology in the form of a temperature-shear rate logarithm diagram is proposed. Application of the proposed methodology makes it possible to simplify the development of new materials for 3D printing by fused deposition modeling both at the stage of selecting the components of the polymer composition and at the stage of its subsequent approbation.

In our study we investigated the additive manufacturing (AM) of ceramic-based Functionally Graded Materials (FGM) by the direct AM technology Thermoplastic 3D-Printing (T3DP). Zirconia components with a varying microstructure were additively manufactured by using thermoplastic suspensions with different contents of pore forming agents (PFA) and were co-sintered defect-free. Different materials were investigated concerning their suitability as PFA for the T3DP process. Different zirconia-based suspensions were prepared and used for AM of single- and multi-material test components. All samples were sintered defect-free and in the end we could realize a brick wall-like component consisting of dense (<1% porosity) and porous (approx. 5% porosity) zirconia areas to combine different properties in one component. The T3DP opens the door to AM of further ceramic-based 4D-components like multi-color or multi-material, especially multi-functional components.

In this study, a three-dimensional bioelectrochemical reactor system (3D-BERs) with granular activated carbon (GAC) epitomizes a novel treatment technology for treating nitrate-polluted water. The conventional denitrification process faces many challenges, including the huge demand for organic carbon, long-term accumulation of intermediate products, and the adaptation period. Results shown that under the optimal conditions of the COD/NO3--N ratio was 1.5, the denitrification efficiency reached 98.62%, when compared to 81.12% at COD/ NO3--N ratio of 3.5, and the initial pH of 7.5 ± 0.5, NO3--N was entirely removed at 2.2 h without accumulation of nitrite. The high initial ratio of NO2--N/NO3--N is mainly to accelerate the denitrification rate by accelerating the reduction of nitrite. Denitrification process followed by zero-order kinetics linear model for at different concentrations of inlet NO3--N, and achieved higher denitrification rate at greater inlet NO3--N concentration. High-throughput sequencing shows that the community structure and relative abundance of bacteria changed significantly, especially at the genes and the phyla level in immobilized GAC particles. Microbial composition enhanced the removal of nitrogen at the inner surface (IS) and bottom surface (BS) of immobilized GAC carriers. Therefore, this system is expected to be a more efficient and useful supplement or a cost-effective alternative compared to the traditional low carbon to nitrogen wastewater treatment system.

A novel physiologically based algorithm (PBA) for the computation of fractional flow reserve (FFR) in coronary artery trees (CATs) using computational fluid dynamics (CFD) is proposed and developed. The PBA is based on the extension of Murray's law and additional inlet conditions prescribed iteratively, and is implemented in OpenFOAM for testing and validation. 3D models of CATs are created using CT scans and computational meshes, and the results are compared to in-vasive coronary angiographic (ICA) data to validate the accuracy and effectiveness of the PBA. The discrepancy between calculated and experimental FFR is within 2.33-5.26% in steady-state and transient simulations, respectively, when convergence is reached. The PBA is a reliable and physiologically sound technique compared to the current lumped parameter model (LPM), which is based on empirical scaling correlations and requires nonlinear iterative computing for conver-gence. The accuracy of the PBA method is further confirmed using the FDA nozzle, which demonstrates good alignment with CFD-validated values.

The results of studying the effect of particles of few-layer graphene (FLG) synthesized by self-propagating high-temperature synthesis (SHS) on the complex of strength and thermo physical properties of polymer composite products obtained by DLP 3D printing are presented. It has been discovered to achieve an increase in thermo physical and strength parameters of polymers modified by FLG compared with samples made on the unmodified base resin. This result was achieved due to low defectiveness, namely the absence of Stone-Wales defects in the structure of FLG due to the homogeneous distribution of FLG over the volume of the polymer in the form of highly dispersed aggregates. It was possible to increase hardness by 120 %, bending strength by 102 %, Charpy impact strength by 205 %, and thermal conductivity at 25 °C by 572 % at concentrations of few-layer graphene of no more than 2 wt. %.

Background: Early diagnosis of postoperative complications is an urgent task, allowing timely prescribing of appropriate therapy and reducing the cost of patient treatment. Prognostic models based on various data could help in the early diagnosis of postoperative complications after cardiac surgery. Objectives: The purpose of the study was to determine whether an integrated approach based on clinical data along with metabolites and biomarkers had greater predictive value than the models built on less data. Methods: The study included patients (n=62) admitted for planned cardiac surgery (coronary artery bypass grafting with cardiopulmonary bypass), who were retrospectively divided into two groups depending on the presence (n=26) or absence (n=36) of postoperative complications of all types. Clinical and laboratory data on the first day after surgery were analyzed. Additionally, patients' blood samples were collected before and on the first day after surgery to determine biomarkers (interleukin-6, procalcitonin, NT-proBNP, high-sensitivity troponin T) and metabolites (8 aromatic and 2 dicarboxylic acids were detected using gas chromatography-mass spectrometry). Results: Patients before surgery, compared with healthy donors, differed in the concentration of metabolites (p &lt; 0.05), and had concentrations of a number of biomarkers exceeding the corresponding reference values. Multivariate PLS-DA models, predicting the presence or absence of postoperative complications, were built using clinical data (ROC-AUC=0.71), concentrations of metabolites and biomarkers (ROC-AUC=0.60), and the entire data set (ROC-AUC=0.75). For comparison we built univariate models using the EuroScore2 (ROC-AUC=0.59) and SOFA (ROC-AUC=0.76) scales; concentrations of lactate (ROC-AUC=0.71), the dynamic changes of 4-hydroxyphenyllactic acid (ROC-AUC=0.69), and the sum of three sepsis-associated metabolites (ROC-AUC=0.70). The proposed complex model using entire data set was comparable to the SOFA scale, which confirms the expediency of searching for new predictive models based on a variety of factors.

Milk serves as a crucial source of natural bioactive compounds essential for human nutrition and health. The gastrointestinal digestion of milk proteins releases various biologically active peptides that positively impact human health and enhance physiological performance. With the growing production of cheese, Greek yogurt, and other dairy products, the volume of unutilized acid whey is significantly increasing. Acid whey, containing almost all whey proteins and approximately one-quarter of casein, presents a valuable raw material for generating peptides with potential health benefits. These peptides exhibit properties such as antioxidant, antimicrobial, anti-inflammatory, anticarcinogenic, antihypertensive, antithrombotic, opioid, mineral-binding, and growth-stimulating activities, contributing to improved human immunity and the treatment of chronic diseases. Enzymatic hydrolysis of milk proteins has been developed as a method to produce these peptides, facilitating their use in food fortification. To incorporate whey into functional beverages, it undergoes fermentation by lactic acid bacteria with proteolytic activity. To specifically enrich these beverages with peptides exhibiting targeted bioactivities, it is essential to select lactic acid bacteria strains possessing the requisite protease profiles. Additionally, the sensory properties of the final product can be enhanced using starter cultures with diverse metabolic capabilities, even in the absence of added flavoring agents. Given the imperative to develop waste-free technologies and enhance the profitability of the dairy industry, there is a growing need to efficiently utilize and transform acid whey into a broad spectrum of valuable products and food additives. This approach is justified not only by the nutritional benefits of the bioactive components in whey but also by the commercial potential of safe and health-enhancing products.

TThe paper presents the results of research on the influence of the settings of lubrication and cooling system parameters (solenoid valve opening time and lubricant feed pressure in terms of its quantity) in order to select the optimal lubricating conditions and thus reduce the wear of the dies used in the first forging operation of the valve forging made of high-nickel steel. Based on the observation of lubrication in the industrial process, it was found that a significant part of the lubricant fails to reach the die cavity, reaching the outside of it, which causes die wear due to seizure resulting from adhesion of the forging material to the tool surface, as well as high lubricant consumption and dirt in the press chamber. The authors proposed their own mobile lubricating and cooling system, which allows for a wide range of adjustments and provided with automatic cleaning procedures of the entire system, unlike the fixed lubrication system used so far in the industrial process. First, tests were carried out in laboratory conditions to determine the highest wettability and the lubricant remaining inside the tool cavity. These tests determined the lubrication system parameter settings which ensured that the greatest amount of lubricant remains in the cold die cavity without the forging process. Then, to verify the obtained results, tests were carried out in the industrial process of hot die forging of valve forgings, for short production runs of up to 500 forgings. The results were compared with the measurement of changes in the geometry of tools and forgings based on 3D scanning and surface topography analysis with the use of SEM. For best results (the variant of the setting of the dose and the time of exposure to lubricant), the forging process was carried out with the use of a new tool, up to the maximum service life.

Background and objectives: Induction chemotherapy (ICT) before definitive chemoradiation (CRT) gives high response rates in LA-SCCHN. However, pre-ICT gross tumour volume (GTV) for radiotherapy (RT) planning is still recommended. As ¹⁸F-FDG PET/CT has an advantage of biological tumour information comparing to standard imaging methods, we aimed to evaluate the feasibility of ¹⁸F-FDG PET/CT-based post-ICT GTV delineation for RT planning in LA-SCCHN and to assess the prognostic value of PET parameters: maximum standardized uptake value (SUV_max), metabolic tumour volume (MTV) and total lesion glycolysis (TLG). Methods: 47 LA-SCCHN patients were treated with 3 cycles of ICT (docetaxel, cisplatin, and 5-fluorouracil) followed by CRT (70 Gy in 35 fractions with weekly cisplatin). Pre- and post-ICT PET/CT examinations were acquired. Planning CT was co-registered with post-ICT PET/CT and RT target volumes were contoured according to post-ICT PET. Post-ICT percentage decrease of SUV_max, MTV and TLG in primary tumour and metastatic regional lymphnodes (LN) was counted. Loco-regional failure patterns, 3-year progression free (PFS) and overall survival (OS) were evaluated. Results: 3-year PFS and OS rates for study population were 67% and 61% respectively. 31.9% of patients progressed loco-regionally. All progresses were localised in high-to-intermediate dose (60–70 Gy) RT volumes and none in low dose (50 Gy) volumes. Decrease of SUV_max ≥74% (p = 0.03), MTV ≥ 68% (p = 0.04), TLG ≥ 76% (p = 0.02) in primary tumour, and LN TLG decrease ≥74% (p = 0.03) were associated with PFS. Decrease of primary tumour SUV_max ≥ 74% (p = 0.04), MTV ≥ 69% (p = 0.04), TLG ≥ 74% (p = 0.02) and LN TLG ≥ 73% (p = 0.02) were prognostic factors for OS. Conclusions: According to our results, 18F-FDG PET/CT-based post-ICT GTV delineation is feasible strategy without negative impact on loco-regional control and survival. Percentage decrease of metabolic PET parameters SUV_max, MTV and TLG has a prognostic value in LA-SCCHN.

The paper focuses on the application of a multilevel, integrative and territorial approach to the protection of cultural heritage through planning instruments in Serbia. It points out the problems of the sectoral approach and discusses international recommendations that can be integrated into the planning methodology. The case study is the area of Djerdap National Park, which has an already established international and national importance. The research suggests that the cultural heritage in the area, with the exception of the Roman limes, is still recognized at the level of individual localities. The study emphasizes the importance of aligning all levels of governance to safeguard the whole spatial entity rather than focusing solely on its particular areas. The interna-tional and national importance of the planning area contributes to the strengthening of awareness of heritage and its institutional protection. However, the vitality of the area, which is key to its sustainable development, comes from the local level. Planning documents contribute to the inte-gration of local values and local communities into development programs and projects.

In order to shorten the detection time and improve the average precision on embedded devices, A lightweight and high accuracy model is proposed for passion fruit in complex environments (backlight, occlusion, overlap, sunny, cloudy, rainy). Firstly, replacing the backbone network of YOLOv5 with a lightweight GhostNet model reduces the number of parameters and computation while improving detection speed. Secondly, a new feature branch is added to the GhostNet network, and the feature fusion layer in the neck network is reconstructed to effectively combine the lower-level and higher-level features, which not only improves the accuracy of the model but also maintains its lightweight. Finally, the knowledge distillation methods are used to transfer the knowledge from the more capable teacher model to the less capable student model, which significantly improving the detection accuracy. The improved model is denoted as G-YOLO-NK. The average accuracy of the G-YOLO-NK network is 96.00%, which is 1.00% higher than the original YOLOv5s model. Furthermore, the improved model size is 7.14MB, reduced to half of the original model, and the real-time detection frame rate is 11.25 FPS on the Jetson Nano. Compared to the state-of-the-art model, the proposed model outperforms them in terms of average precision and detection performance. The present work provides an effective model for real-time detection of passion fruits in complex orchard scenes, which can provide valuable technical support for the development of orchard picking robots and greatly improve the intelligence level of orchards.

The impact of interaction SS with MJO on rainfall along Java Island to East Nusa Tenggara has been studied using daily rainfall observation data from 2140 weather observation stations, which are also equipped with GSMaP, OLR, and ERA5 data. There were 61 SS events found, 17 during active MJO and 44 in inactive MJO. Rainfall increases more in the western study area when the active MJO and more in the eastern study area when the inactive MJO is due to SS. SS reduces rainfall in the Jakarta region, regardless of the activity or inactivity of the MJO. SS causes extreme rainfall to only occur in a small part of certain areas, so it tends to significantly reduce the possibility of extreme rainfall. In the southern part of the IMC, SS predominates over MJO in supporting increased water vapor transport. Large-scale synoptic circulations like the monsoon, SS, and MJO can interact with local land-sea wind circulation to produce spatiotemporal variability in rainfall on Java Island. Rainfall mostly increases in the afternoon and decreases in the morning when SS occurs, whether there is MJO or not. Convective instability analysis indicates that SS increases precipitation, most likely by lowering CIN and raising VIMFC.

The Simultaneous Localization And Mapping (SLAM) scanner is an easy and portable Light Detection And Ranging (LiDAR) data acquisition device. Its main output is a 3D point cloud covering the scanned scene. Regarding the importance of accuracy in the survey domain, this paper aims to assess the accuracy of two SLAM scanners: the NavVis VLX and the BLK2GO Scanner. This assessment is conducted for both outdoor and indoor environments. In this context, two types of reference data are used: the Total Station (TS) and the static scanner Z+F Imager 5016. To carry out the assessment, four comparisons are tested: cloud to cloud, cloud to mesh, mesh to mesh, and edge detection board assessment. However, the results of the assessments confirm that the accuracy of indoor SLAM scanner measurements (5 mm) is greater than that of outdoor ones (between 10 mm and 60 mm). Moreover, the comparison of cloud to cloud provides the best accuracy regarding direct accuracy measurement without manipulations. Finally, based on the high accuracy, scanning speed, flexibility, and the accuracy differences between tested cases, it is confirmed that SLAM scanners are effective tools for data acquisition.

Abstract Purpose: This study aims to evaluate the potential of multimodal ultrasound techniques in improving the visibility of liver lesions that are indistinct under conventional ultrasound. Specifically, we will explore the application of fusion imaging, contrast-enhanced ultrasound (CEUS), and high-frequency ultrasound in enhancing the visibility of liver masses. These techniques will be utilized to assist in visualizing liver lesions and to accurately localize them for the purpose of performing percutaneous tissue biopsy. Lastly, we will compare the biopsy results with the final diagnosis to assess whether multimodal techniques can enhance the success rate of percutaneous biopsy for liver masses that are not clearly visible under conventional ultrasound. Furthermore, the potential impact of these techniques on the development of personalized treatment strategies for patients was also discussed. Materials and Results: A retrospective analysis was conducted on 144 patients with liver masses who underwent conventional ultrasound examinations at our hospital from October 2018 to January 2024. These patients had poor visibility on conventional ultrasound, but the tumor location was visible on abdominal computerized tomography (CT) or magnetic resonance imaging (MRI) scans. We excluded 71 patients who did not undergo percutaneous liver tumor biopsy and 8 patients who remained non-visualized under multimodal ultrasound. Finally, 95 patients met the inclusion criteria and their clinical and radiological data were selected for analysis. Computerized tomography or magnetic resonance imaging-ultrasound (CT/MR-US) fusion imaging was performed in 55 patients, CEUS was conducted in 95 patients, and high-frequency ultrasound examination was performed in 21 patients. The visibility of the lesions using these three techniques was evaluated, and the consistency between the biopsy pathology and the final diagnosis was analyzed. Results: In the study, a total of 39 cases were identified as solitary liver lesions, 34 cases as multiple lesions, and an additional 23 cases as diffuse hepatocellular carcinoma. Among them, there were 13 cases (13.7%) of lesions located in the left lobe, 73 cases (76.8%) in the right lobe, and 9 cases (9.4%) at the junction of the left and right lobes. The average maximum diameter of the lesions was 2.7 cm (ranging from 0.7 cm to 10.0 cm). The detection rates of lesions using CT/MR-US fusion imaging, contrast-enhanced ultrasound (CEUS), and high-frequency ultrasound examination were 49.1%, 96.8%, and 76.2%, respectively. All patients in the entire cohort underwent percutaneous ultrasound-guided biopsy after confirming the target location of the lesions, including 9 patients underwent percutaneous microwave ablation. No severe complications were observed. The accuracy rate of the biopsies was 91.6%, and the positive concordance rate was 91.1%. The biopsy pathology included 39 cases of hepatocellular carcinoma (HCC), 16 cases of intrahepatic cholangiocarcinoma (ICC), 22 cases of metastatic adenocarcinoma, 3 cases of hepatic adenoma (HA), 1 case of vascular sarcoma, and 1 case of mixed HCC-ICC. Among the 13 patients with negative pathology findings after biopsy, 8 cases were considered false negatives (based on follow-up laboratory tests and imaging results consistent with malignant tumor characteristics), resulting in a false negative rate of 8.9%. Conclusions: The application of multimodal ultrasound technology can significantly improve the success rate of liver lesion biopsies that are difficult to visualize using conventional ultrasound. Furthermore, it will facilitate the guidance of microwave ablation therapy for lesions using multimodal ultrasound imaging, enabling collaborative precision treatment planning for patients with clinical physicians.

Present work investigates, in photon energy domains of specific interest for medical imaging, the effect of the escape of X-ray fluorescence from the scintillator materials on the energy resolution of scintillation detector itself. Monolithic as well as pixelated crystals differently sized are considered, in the case of the NaI because it is the gold standard in the field. The volumetric ratio is introduced, as a figure of merit, taking into account, alongside the surface-to-volume ratio, the geometric shape, the elemental composition and also the mean-free-path for the given scintillator and energy. The inter-crystal XRF escape is finally suggested to be considered among the effects producing image blurring in segmented scintillatros due to the spread of events between the primary pixel and the first neighbors ones.

Non-invasive radionuclide imaging of human epidermal growth factor receptor type 2 (HER2) expression in breast, gastroesopha-geal and ovarian cancers may stratify patients for treatment using HER2-targeted therapeutics. Designed ankyrin repeat proteins (DARPins) are a promising type of targeting probes for radionuclide imaging. In clinical studies, the DARPin [99mTc]Tc-(HE)3-G3, labeled using a peptide-based chelator His-Glu-His-Glu-His-Glu ((HE)3), provided clear imaging of HER2 expressing breast cancer 2-4 h after injection. The goal of this study was to evaluate if the use of cysteine-containing peptide-based chelators Glu-Glu-Glu-Cys (E3C), Gly-Gly-Gly-Cys (G3C), and Gly-Gly-Gly-Ser-Cys connected via a (Gly-Gly-Gly-Ser)3-linker (designated as G3-(G3S)3C) would further improve the contrast of imaging using 99mTc-labeled derivatives of G3. The labeling of the new variants of G3 provided a radiochemical yield over 95%. Labeled G3 variants bound specifically to human HER2-expressing cancer cell lines with affinity in the range 1.9-5 nM. Biodistribution of [99mTc]Tc-G3-G3C, [99mTc]Tc-G3-(G3S)3C, and [99mTc]Tc-G3-E3C in mice was compared with the biodistribution of [99mTc]Tc-(HE)3-G3. It was found that the novel variants provide specific accumulation in HER2-expressing human xenografts and enable discrimination between tumors with high and low HER2 expression. However, [99mTc]Tc-(HE)3-G3 provided better contrast between tumors and the most frequent metastatic sites of HER2-expressing cancers and is therefore more suitable for clinical applications.

The aim of this research is to investigate and use a variety of immersive multisensory media techniques in order to create convincing digital models of fossilised tree trunks for use in XR. This is made possible via the use of geospatial data derived from sources such as aerial imaging using UAS, terrestrial material using cameras and also include both the visual and audio element for better immersion, accessible and explorable in 6 Degrees of Freedom (6DoF). Immersiveness is a key factor in order to result in output that is especially engaging to the user. Both conventional and alternative methods are explored and compared, emphasising in the advantages made possible via the help of Machine Learning Computational Photography. Material is collected using both UAS and terrestrial camera devices, including a 3D-360º camera with 6 sensors, using stitched panoramas as sources for photogrammetry processing. Difficulties such as capturing large free standing objects using terrestrial means were overcome using practical solutions involving mounts and remote streaming solutions. Conclusions indicated that superior fidelity can be achieved by the help of Machine Learning Computational Photography processes and higher resolutions and technical specs of equipment not necessarily translating to superior outputs.

Antimicrobial application of carbon nanomaterials such as carbon nanotubes (CNTs), capped CNT, C60 fullerene, and C70 fullerene are increasing owing to their low cytotoxicity properties compared to other nanomaterials such as metallic nanoparticles. Enhanced mechanical property and antibacterial activity can be caused by incorporation of CNTs in 3-dimentional (3D) printed nanocomposites (NCs). Interruption of bacterial membrane resulting from cylindrical shape and high aspect ratio properties has been found as the prominent antibacterial mechanism of CNTs. However, unraveling interaction of CNT, capped CNT, C60 fullerene, and C70 fullerene with virulence factors of the main bacterial pathogenesis has not yet been known. Therefore, in the present study, interactions of CNT, capped CNT, C60, and C70 with the eight virulence factors including protein kinase A and ESX-secreted protein B of Mycobacterium tuberculosis, pseudomonas elastase and exotoxin A of Pseudomonas aeruginosa, alpha-hemolysin and penicillin binding protein 2a of Staphylococcus aureus and shiga toxin 2a and heat-labile enterotoxin of Escherichia coli have been evaluated by molecular docking method of AutoDock Vina. This study disclosed the binding strength followed the sequence CNT &gt; capped CNT &gt; C70 &gt; C60 towards alpha-hemolysin of S. aureus compared to other virulence factors with values of -19.6, -18.8, -13.6, and -12.8 kcal/mol, respectively. The lowest and highest binding affinity were found for CNT against 1TII and 1MWT by binding energy values of 97.4 and -20.1 kcal/mol. The stability of CNT-1MWT complex at the different times has resulted according to the normal mode analysis of elNémo and iMOD servers. Future studies should be focused on improving cellular uptake of CNTs, capped CNTs, C70, and C60 by surface functionalization for active targeting of bacteria.

Electric energy has become essential nowadays not only for the daily life of each of us but also for the economy of different countries. The dissemination of geographic information plays an important role in national development as it facilitates communication between managers, investors, and consumers in this sector. Since the management of electricity network data was previously done in Tunisia based on paper maps and plans, the purpose of this article is to present a case of planning based on GIS, Web, and 3D Web GIS, which would have significant positive consequences on this sector from a technical and financial sides with an improvement in customer satisfaction and the creation of an intelligent electricity network which will be a real decision-making tool. This work draws up an inventory of the network MV (Medium Voltage)/LV (Low Voltage) of the region of Medjez El Bab which routes electricity to the big centers of consumption with access to MV/LV subscribers. The analysis of the network's impedance allowed carrying out different scenarios to optimize performance and obtain more realistic routes. Many thematic maps were produced as part of this project (Slope map, Land use map, map of the MV voltage domains, map of the MV/LV transformer stations power, etc.). A three-dimensional virtual city has been developed to visualize the graphical and attribute data for the study area. A Web and 3D Web GIS applications that allows the publication of the interactive maps on the Web as well as the database information have been developed to offer users the possibility of consulting the produced products by internet. Finally, a website related to the study was developed.

In recent years, electroencephalogram (EEG) emotion recognition has emerged as a research hotspot in the field of artificial intelligence (AI). Despite advancements in EEG-based emotion recognition, room for enhancing performance persists due to EEG signal redundancy and limitations in feature extraction, leading to inefficient models and emotional information loss. To fully utilize EEG's emotional information and improve recognition accuracy while reducing computational costs, this paper proposes a Convolutional-Recurrent Hybrid Network with a dual-stream adaptive approach and an attention mechanism (CSA-SA-CRTNN). Firstly, the model utilizes a CSAM module to assign corresponding weights to EEG channels. Then, an adaptive dual-stream convolutional-recurrent network (SA-CRNN and MHSA-CRNN) is applied to extract local spatial-temporal features. After that, the extracted local features are concatenated and fed into a temporal convolutional network with a multi-head self-attention mechanism (MHSA-TCN) to capture global information. Finally, the extracted EEG information is used for emotion classification. We conducted binary and ternary classification experiments on the DEAP dataset, achieving 99.26% and 99.15% accuracy for arousal and valence in binary classification, and 97.69% and 98.05% in ternary classification, surpassing relevant algorithms. Additionally, the model's efficiency is significantly higher than other models, achieving better accuracy with lower resource consumption.

Glycosidic linkage analysis was conducted on the unfractionated polysaccharides in the alcohol-insoluble residues (AIRs) prepared from six red seaweeds (Gracilariopsis sp., Prionitis sp., Mastocarpus papillatus, Callophyllis sp., Mazzaella splendens, and Palmaria palmata) using GC-MS/FID analysis of partially methylated alditol acetates (PMAAs). The cell walls of P. palmata primarily contained mixed-linkage xylans and small amounts of sulfated galactans and cellulose. In contrast, the unfractionated polysaccharides of the other five species were rich in galactans displaying diverse 3,6-anhydro-galactose and galactose linkages with varied sulfation patterns. Different levels of cellulose were also observed. This glycosidic linkage method offers advantages for cellulose analysis over traditional monosaccharide analysis that is known for underrepresenting glucose in crystalline cellulose. Relative linkage compositions calculated from GC-MS and GC-FID measurements showed that anhydro sugar linkages generated more response in the latter detection method. This improved linkage workflow presents a useful tool for studying polysaccharide structural variations across red seaweed species. Furthermore, for the first time, relative linkage compositions from GC-MS and GC-FID measurements, along with normalized FID and total ion current (TIC) chromatograms without peak assignments, were analyzed using principal component analysis (PCA) as a proof-of-concept demonstration of the technique's potential to differentiate various red seaweed species.

Background: Educating college students about the importance of good sleep habits could lead to the adoption of healthier sleep routines, including sufficient sleep duration and sleep quality. The current pre-post study examines the impact of completing a sleep education program called “Sleep 101” on (1) sleep hygiene practices, (2) sleep quality, and (3) weekday and weekend sleep behaviors among college students. “Sleep 101” is an interactive online course developed to educate college students about the importance of sleep by addressing basic sleep physiology, the impact of sleep on mood, academic and physical performance, the interactions between sleep and various substances, and common sleep disorders. Methods: 338 college students were recruited from a midsized public university in the US and invited to participate in “Sleep 101”, of which 25 participants completed the baseline and post-intervention questionnaire. The Sleep Hygiene Index (SHI) was utilized to evaluate sleep hygiene practices, while standard questions were employed to assess weekday and weekend sleep behaviors and overall sleep quality. Results: Those who completed the study demonstrated a significant increase in weekday sleep duration and were less likely to engage in negative prior bedtime activities. In addition, 40% of those who completed baseline and post-intervention assessments noticed improvements in their sleep quality. Conclusion: These findings suggest that a brief online program is beneficial in improving sleep behaviors among college and could be a scalable approach to addressing current sleep issues and preventing future sleep problems in college students.

The profile of secondary metabolites occurring in apple cuticular layer is not only characteristic for particular apple cultivar, but also dynamically reflects various external factors in growing environment. In this study, the possibility to authenticate apple samples based on analysis of their cuticular layer extracts was investigated. Ultra-high-performance liquid chromatography coupled to high resolution tandem mass spectrometry (UHPLC-HRMS/MS) was employed for obtaining metabolomic fingerprints. In total, 274 authentic apple samples, four cultivars harvested within the seasons 2020 to 2022 in the Czech Republic and Poland were analysed. The generated complex data processed by univariate and multivariate statistical methods enabled to build classification models for discrimination of apple cultivars as well as their geographical origin. The models showed very good performance in differentiation of Czech and Polish samples for three of four cultivars: ‘Gala’, ‘Golden Delicious’ and ‘Idared’, moreover, the validity of the models was verified over harvest seasons. The diagnostic markers, besides metabolites of triterpene biosynthetic pathway, mainly represented wax esters. ‘Jonagold’, which is known to be susceptible to mutations, was the only cultivar for which the unambiguous classification of geographical origin was not possible.

This paper presents an original method of additive manufacturing of cylindrical parts with variable circumference thickness, which allows the control of the deposition of molten material using an algorithm for decomposing the part geometry into volumetric elements with known dimensional configuration. In the absence of a post-processor capable of controlling additive manufacturing on a 5-axis numerical control machine, control of the deposition of molten material is done using parameterized programs, which can control both the feed speeds of the machine tool axes and the specific functions of the printing equipment. Additive manufacturing can make a positive contribution to sustainable development compared to traditional manufacturing technologies, thus making a positive contribution for a sustainable future. The aim of the work is to make it possible to 3D print parts with variable wall thickness using a CNC machining centre. To obtain the variable thickness layer we have implemented an original method of deposition with molten material (FDM), the coordination of the system composed of physical elements respectively programmable elements, is realized through control functions materialized in parameterized part programs, the generated outputs being the variable speed of the machine axes on a circular trajectory, the angular positioning, the filament advance.

Superior fiber quality is one of the most important objectives in cotton breeding. To detect the genetic basis underlying fiber quality, an F2 population containing 413 plants was constructed by crossing Jifeng 914 and Jifeng 173, both of which have superior fiber quality, with Jifeng 173 being better. Five fiber quality traits were investigated in the F2, F2:3, F2:4, and F2:5 populations. Quantitative trait loci (QTL) mapping was conducted based on a high-density genetic map containing 11,488 single nucleotide polymorphisms (SNPs) and spanning 4,202.12 cM in length. Transgressive segregation patterns and complex correlations in the five tested traits were observed. A total of 108 QTLs were found, including 27 for fiber length (FL), 16 for fiber strength (FS), 24 for micronaire (MC), 17 for fiber uniformity (FU), and 24 for fiber elongation rate (FE). Chromosome A7 contained 12 QTL, ranking the first. No QTL was found on chromosome D1 and D11. Each QTL contributed 1.98%–21.45% to the phenotypic variation (PV), including 13 major effect QTLs that contributed more than 10% toward PV. Two QTLs could be repeatedly detected in three populations, including qFL-D3-2 in F2, F2:4, and F2:5 with 9.18%–21.45% of PV, qFS-A11-1 in F2:3, F2:4 and F2:5 with 6.05%–10.41% of PV. Another seven stable QTLs could be detected in two populations, including four major effect QTLs: qFL-A12-3, qFS-D10-2, qMC-D6-2, and qMC-D8-1. Fourteen QTL-overlapping regions were found, which might explain the complex correlations among the five phenotypic traits. Four regions on chromosome A11, D3, D6, and D10 covered by both stable and major effect QTLs are promising for further fine mapping. The genomic regions of the two QTLs detected in three populations and the four major effect QTLs contain 810 genes. Gene functional analysis revealed that the annotated genes are mainly involved in protein binding and metabolic pathways. Fifteen candidate genes in the qFL-D3-2 region are highly expressed in fiber or ovules during fiber initiation, elongation, secondary cell wall thickening, or maturation stages. qRT-PCR revealed that Ghir_D03G005440.1 and Ghir_D03G011310.1 may play a role in promoting fiber initiation, Ghir_D03G006470.1 may be beneficial for promoting fiber elongation. This study provides more information for revealing the molecular genetic basis underlying cotton fiber quality.

Rotational jumps are crucial techniques in sports competitions. Estimating ground reaction forces (GRFs), one of the components constituting jumps, through a biomechanical model-based approach enables analysis even in environments where force plates or machine learning training data cannot be utilized. In this study, rotational jump movements involving twists on land were measured using inertial measurement units (IMUs) and estimated GRFs and body loads using a 3D forward dynamics model. Our estimation method, based on forward dynamics and optimization calculations, generated and optimized body movements using cost functions defined by motion measurements and internal body loads. To reduce the influence of the dynamic acceleration in the optimization calculation, the 3D orientation using sensor fusion composed of acceleration and angular velocity data obtained from IMUs and an extended Kalman filter was estimated. As a result, by generating movements based on the cost function, it was possible to calculate biomechanically valid GRFs while following the measured movements even if not all joints are covered by IMUs. This estimation method allows for 3D motion analysis independent of measurement conditions or training data.

Type 1 diabetes is a chronic condition that results from the destruction of insulin-producing β-cells in the pancreas. Current treatments for type 1 diabetes, such as insulin therapy and pancreatic islet transplantation, have several limitations and, hence not quite effective in the long run. As current therapy methods fail to slow disease development, novel strategies such as the development of a bioartificial pancreas are being seriously considered. Over the last decade, research has focused on tissue engineering, which aids in the design of biological alternatives for the repair and replacement of non-functional or damaged organs. Three dimensional (3D) bioprinting technology which employs 3D printing technology to generate 3D tissue-like structures from biomaterials and cells, offers a promising solution for the treatment of type 1 diabetes by providing the ability to generate functional endocrine pancreatic tissue. Bioprinted structures are therefore an important aspect of tissue engineering because they have been found to replicate the native extracellular matrix, promoting cell survival and proliferation. In this review, we extensively discussed about bioprinting endocrine pancreas for the treatment of type 1 diabetes particularly focussing on the choice of cells, biomaterials, growth factors, and essential considerations. Additionally, the key challenges and perspectives towards recapitulation of the pancreatic function of the pancreatic organ engineering technologies have also been discussed.

We present a novel method for online measurement of multi-point opening distances of midpalatal suture during rapid palatal expansion (RPE) using fiber optic Fabry-Perot (F-P) sensors. The sensor consists of an optical fiber with a cut flat end face and an optical reflector, which are implanted into the palatal base structure of an expander and is capable of measuring the precise distance between two optical reflective surfaces. As a demonstration, a 3D printed skull model containing the maxilla and zygomaticomaxillary complex (ZMC) was produced and a miniscrew-assisted rapid palatal expander (MARPE) with two guide rods was used to generate the midpalatal suture expansion. The reflected spectrums of the sensors were used to dynamically extract cavity length information for full process monitoring of expansion. The dynamic opening of the midpalatal suture during the gradual activation of the expander was measured, and a displacement resolution of 2.5 μm was demonstrated. The angle of expansion was derived and the results suggested that the midpalatal suture was opened with a slightly V type expansion of 0.03 rad at the first loading and subsequently expanded in parallel. This finding might be useful for understanding the mechanical mechanisms that lead to different types of expansion. The use of a fiber-optic sensor for mounting the rapid palatal expander facilitates biomechanical studies and experimental and clinical evaluation of the effects of RPE.

In an industrial environment, the quality assurance of weld seams requires extensive efforts. The most commonly used methods for that are expensive and time-consuming destructive tests, since quality assurance procedures are difficult to integrate into production processes. Beyond that, available test methods allow only the assessment of a very limited set of characteristics. They are either suitable for determining selected geometric features or for locating and evaluating internal seam defects. The presented work describes an evaluation methodology based on microfocus X-ray computed tomography scans (µCT scans) which enable the 3D characterization of weld seams, including internal defects such as cracks and pores. A 3D representation of the weld contour, i.e., the complete geometry of the joint area in the component with all quality-relevant geometric criteria, is an unprecedented novelty. Both the dimensions of the weld seam and internal defects can be revealed, quantified with a resolution down to a few micrometers and precisely assigned to the welded component. On the basis of the methodology developed within the framework of this study, the results of the scans performed on the alloy AA 2219 can be transferred to other aluminum alloys. In this way, the data evaluation framework can be used to obtain extensive reference data for the calibration and validation of inline process monitoring systems employing Deep Learning-based data processing.

Crystallization is a significant procedure in the manufacturing of many pharmaceutical and solid food products. In-situ Electrical Resistance Tomography (ERT) is a novel Process Analytical Tool (PAT) to provide a cheap and quick way to test, visualize, and evaluate the progress of crystallization processes. In this work, the spatial accuracy of the non-conductive phantoms in low conductivity solutions was evaluated. Gauss-Newton, Linear Back Projection, and iterative Total Variation reconstruction algorithms were used to compare the phantom reconstructions for tap water, industrial-grade saturated sucrose solution, and demineralized water. Cylindrical phantom measuring 10 mm in diameter and a cross-section area of 1.5 % of the total beaker area was detected at the center of the beaker. Two phantoms with a 10 mm diameter were visualized separately in non-central locations. The quantitative evaluations were done for the phantoms with radii ranging from 10 mm to 50 mm in demineralized water. Multiple factors such as ERT device and sensor development, FEM mesh density and simulations, image reconstruction algorithms, number of iterations, segmentation methods, and morphological image processing methods were discussed and analyzed to achieve spatial accuracy. The development of ERT imaging modality for the purpose of monitoring crystallization in low conductivity solutions was performed satisfactorily.

Turbulent flows over and within forest canopies have recently been modeled with success using Large Eddy Simulations (LES). Validation exercises against experimental data suggest that models can be applied with a high degree of confidence for many applications, mechanical and physiological plant/atmosphere interaction analysis, seed or pollen dispersal, wildfire spread and firebrand transport, or investigation of causes of eddy-covariance technique bias. Long distances required for shear-induced turbulence to equilibrate, result in the widespread use of cyclic boundary conditions in LES atmospheric boundary layer studies. Vegetation drag dissipates air momentum in the atmosphere, but equilibrium is often achieved through compensatory momentum source, supplied by macro-scale pressure gradient forcing. Unfortunately, both classical Ekman balance or simple spatially-constant pressure gradient techniques for implementing this forcing have major drawbacks in the context of cyclic boundary conditions for the applications listed above. Among them, it is difficult to specify aspects of the mean velocity profile such as a specific desired wind velocity and direction at a reference height. In the present paper, we propose a new technique for capturing the effects of a large-scale pressure gradient force (LSPGF) that can be used at stand scale and enables simulation of realistic and specifiable wind fields. Several variants of this LSPGF are developed and analyzed here and validated against experimental data. Although this LSPGF technique is developed in the context of HIGRAD/FIRETEC wildfire simulations, LSPGF can be used for any LES wind modeling application aimed at generating detailed stand-scale wind fields with resolved turbulence and shear profiles consistent with vegetation structure in the boundary layer.

A novel and simple method to improve the corrosion resistance of copper by constructing a 3D 1-dodecanethiol self-assembled monolayers (SAMs) in 3.5% NaCl solution is reported in this study. Several drops of 1% H3PO4 solution are thinly and uniformly distributed on copper surface to form a 3D nanostructure constituted by Cu3(PO4)2 nanoflowers. The anticorrosion properties of 1-dodecanethiol SAMs on copper surface and on copper surface treated with H3PO4 solution were evaluated. Results demonstrated that 1-dodecanethiol SAMs on bare copper surface exhibit good protection capacity, whereas a copper surface pretreated with H3PO4 solution can substantially enhance the corrosion resistance of 1-dodecanethiol SAMs.

Currently there are fewer depth models applied to pepper picking detection, while the existing generalized neural networks have problems such as large model parameters, long training time, and low model accuracy.In order to solve the above problems, this paper proposes a Yolo-chili target detection algorithm for chili pepper detection. First, the classical target detection algorithm yolov5 is used as a benchmark model, and an adaptive spatial feature pyramid structure combining the attention mechanism and the idea of multi-scale prediction is introduced to improve the model's detection effect on occluded peppers and small target peppers. Secondly, a three-channel attention mechanism module is introduced to improve the algorithm's long-distance recognition ability and reduce the interference of redundant testers. Finally, the quantized pruning method is used to reduce the model parameters and realize the lightweight processing of the model. Applying the method to the homemade chili pepper dataset, the AP value of chili pepper reaches 93.11%; the accuracy rate is 93.51% and the recall rate is 92.55%.The experimental results show that yolo-chili is able to achieve accurate and real-time pepper detection under complex orchards.

The temporary immersion system bioreactor named GreenTray®[2], [3]presents advantages over the existing ones. Firstly, there is no need to use forceps to move the shoots or plantlets in or out of the recipient, neither the use of scalpel to divide them. Secondly, the basis of the shoot can remain in the GreenTray® and can sprout again in several cycles of growth. These two characteristics reduce the costs in the process of micropropagation. Besides, shoots or plantlets development is enhanced by the aeration of the recipient, thus enriching with CO2 the recipient atmosphere. The chapter describes and provides images and values of interest in (1) the micropropagation process of some commercial Prunus or Pyrus rootstocks; (2) the plantlet growth under autotrophic conditions; and (2) the inoculation of plants with pathogens that reproduce in vitro the symptoms observed in vivo, using the GreenTray® bioreactor.

Aiming at the problems of inaccurate segmentation of long object and information loss of small object in real-time semantic segmentation algorithm, this paper proposes a lightweight multi-branch real-time semantic segmentation network based on BiseNetV2. The new auxiliary branch makes full use of spatial details and context information to cover the long object in the field of view. Meanwhile, in order to ensure the inference speed of the model, the asymmetric convolution is used in each stage of the auxiliary branch to design a structure with low computational complexity. In the multi-branch fusion stage, the alignment and fusion module is designed to provide guidance information for deep and shallow feature mapping, so as to make up for the problem of feature misalignment in the fusion of information at different scales, and thus reduce the loss of small target information. In order to further improve the model’s awareness of key information, a global context module is designed to capture the most important features in the input data. The proposed network uses NVIDIA GeForce RTX 3080 Laptop GPU experiment, on the road street view data set Cityscapes and CamVid average occurring simultaneously ratio reached 77.1% and 78.4% respectively, with running speed of 127 frames/s respectively and 112 frames/s. The experimental results show that the proposed algorithm can achieve real-time segmentation and improve the accuracy significantly, showing good semantic segmentation performance

Strawberry root rot caused by Neopestalotiopsis clavispora is one of the main diseases of strawberry and significantly impacts the yield and quality of strawberry fruit. There are now no effective control techniques available except for fungicide sprays, which may directly impact consumers. Biological control is becoming an alternative method for the control of plant diseases to replace or decrease the application of traditional synthetic chemical fungicides. Trichoderma is widely used as a biological agent for controlling strawberry root rot. In order to provide resources for screening the highly effective biocontrol fungus for controlling strawberry root rot caused by Neopestalotiopsis clavispora, the biocontrol mechanism,the control effects of Trichoderma asperellum CMT10 against strawberry root rot and growth-promoting effects on strawberry seedlings were investigated by plate culture, microscopy observation and root drenching methods.The results showed that CMT10 had obvious competitive, antibiotic and hyperparasitism effects on Neopestalotiopsis clavispora CMGF3. The CMT10 could quickly occupy nutritional space, and the inhibition rates of CMT10 against CMGF3 in confrontation culture on 7 d was 65.49%. The inhibition rates of volatile metabolite and fermentation metabolite produced by CMT10 against CMGF3 were 79.67% and 69.84%, respectively. The mycelium of strain CMT10 can act as hyperparasites by making contacting, winding and penetrating hyphae of CMGF3. Pot experiment showed that the biocontrol efficacy of CMT10 on strawberry root rot caused by Neopestalotiopsis clavispora was 63.00%. CMT10 had obvious promotion effect on strawberry growth, the plant height, root length, total fresh weight, root fresh weight, stem fresh weight and root dry weight, with the promotion rates were 20.09%, 22.39%, 87.11%, 101.58%, 79.82% and 72.33%, respectively. Overall, this study showed the ability of Trichoderma asperellum CMT10 to control strawberry root rot and their potential to develop as novel biocontrol agents to replace chemical fungicides for eco-friendly, sustainable agriculture.

In this paper we study a class of impulsive delayed neural networks with parameter uncertainties and reaction-diffusion terms. Using the properties of M-matrices and some inequality techniques, some sufficient conditions are derived to guarantee the global exponential stability of the given system. The results obtained are presented by simple algebraic inequalities, which are certainly more concise than previous methods. Finally, the validity and usefulness of our results are illustrated by arithmetic examples.

Pyrops candelaria is one of the common pests of fruit trees, but the research on the pathogenic microorganisms it may carry is very limited. Therefore, it is essential to reveal the pathogenic microbes it carries and their potential hazards. This study found a new virus from the transcriptome of P. candelaria, which was first reported in P. candelaria and named as PyCaV (Pyrops candelaria associated virus). RACE and bioinformatics assay revealed that the full-length of PyCaV is 10855 bp with the polyA tail, containing a single open reading frame (ORF) encoding a polyprotein consisting of 3171 amino acid (aa). The virus has a typical Iflavirus structure, including two rhv domains, a RNA helicase domain (HEL), a 3C cysteine protease domain (Pro), and a RNA-dependent RNA polymerase domain (RdRp). Further phylogenetic analysis revealed that this virus belongs to family Iflaviridae and sequence alignements analysis suggedted PyCaV is new member in unassigned genus of family Iflaviridae. Further in-depth analysis of virus-infection-part showed that PyCaV is distributing in the whole longan lanternfly, including its head, chest, and abdomen, but more PyCaV was identified in the chest. The distribution of PyCaV in different parts of P. candelaria was further explored, which showed that more PyCaV were detected in its piercing-sucking mouthparts and chest viscera. Statistical analysis showed that the PyCaV infection was affected by time and locations.

Our aim was to evaluate efficacy and safety of 30mL CaO alone or plus Asc in bowel preparation before colonoscopy. Two hundred and forty six patients were allocated randomly to ingest 2L PEG with 30mL CaO, 1L PEG with 30mL CaO plus 5g Asc, or 3L PEG. We used Boston Bowel Preparation Scale (BBPS) to evaluate bowel preparation efficacy. We also determined other outcomes such as procedure time, polyp or adenoma detection rate and adverse events (AEs). Of 282 patients recruited, 36 were excluded. Groups were matched for baseline characteristics except weight (P = 0.020) and body mass index (BMI) (P = 0.003). Patient’s satisfaction were higher in 2L PEG-CaO (P = 0.016) and 1L PEG-CaO-Asc groups (P = 0·017). Patients’ compliance was 67.5%, 71.4% and 80.5% in 3L PEG, 2L PEG-CaO and 1L PEG-CaO-Asc groups (P = 0.014). Adequate bowel preparation rate was 75%, 78.57% and 53.66% in 3L PEG, 2L PEG-CaO and 1L PEG-CaO-Asc groups (P = 0.021). There were no differences in terms of remaining outcomes. Despite an increase in patients’ satisfaction and compliance, 1L PEG-CaO-Asc significantly decreased adequate bowel preparation rate. However, 2L PEG-CaO improved the patients' satisfaction and compliance and increased adequate bowel preparation rate.

Apis mellifera, especially weak ones, are highly vulnerable to Carpoglyphus lactis mites, which can rapidly infest and consume stored pollen, leading to weakened colonies and potentially colony collapse. This study aimed to ascertain and investigate the prevalence of this mite in honeybee colonies across 9 provinces in the Republic of Korea (ROK). A total of 615 honeybee colonies were collected, from 66 apiaries during the spring and 58 apiaries during the summer of 2023. A 1,242 bp segment of the the Cytochrome c oxidase subunit 1 (COI) gene was amplified using the polymerase chain reaction method. The detection levels of C. lactis in the honeybees were compared between winter and summer. Based on the COI sequence analysis, the nucleotide sequence similarity of C. lactis mites isolated in the ROK with those from China (NC048990.1) was found to be 99.5%, and with those from the United Kingdom (KY922482.1) was 99.3%. This study is the first report of C. lactis in Korean apiaries. The findings in this study demonstrate a significantly higher detection rate in winter, which is 4.1 times greater than that in summer (p &lt; 0.001). Furthermore, the results underscore the usefulness of molecular diagnostic techniques for detecting C. lactis mites.

Seeds can maintain their quality for a limited time; after that, they will lose their germination ability and vigor. Some physiological and physicochemical changes in the structure of the seeds during storage can decrease the quality of the seeds which is known as aging. Therefore, detection of the strong young seeds from the old ones is a vital issue in the modern agriculture. Conventional methods of detection of the seed viability and germination are destructive, time-consuming and costly. In this research, two peanut cultivars, namely North Carolina 2 (NC-2) and Florispan were selected and three artificial aging levels were induced to them. Hyperspectral images (HSI) of the samples were acquired and the seed viability was evaluated using two pre-trained convolutional neural network (CNN) image processing models, AlexNet and VGGNet. The noise of the reflection spectra of the samples was relatively resolved and modified by combining Preprocessing techniques of moving average (MA) and standard normal variate (SNV). Using principal component analysis (PCA), the dimensions were declined and three principal components (PC) were extracted. These PCs were then used as variables in the classification of support vector machine (SVM) and linear discriminant analysis (LDA). The results showed the high capability of CNN architectures such as AlexNet and VGGNet in detection of the seed viability based on the HIS with no pre-processing and feature extraction. The mentioned architectures reached the accuracy of 0.985 and 0.986, respectively. The combination of feature extraction method of PCA with LDA and SVM classifiers showed that the use of a limited number of PCs instead of all wavelengths can decrease the complexity of modeling, while enhancing the efficiency of the models such that LDA and SVM classifiers achieved the accuracy of 0.983 and 0.986 in classification of peanut sees, respectively.

Purpose To analyse diagnostic and therapeutic impact of molecular imaging TNM (miTNM) stage obtained with 18F-DCFPyL versus 18F-Fluorocholine in head to head comparison in biochemical recurrence (BCR) prostate cancer (PCa). Material and methods Patients with BCR PCa after radical treatment with previous 18F-Fluorocholine-PET/CT (negative or oligometastatic disease) were derived to 18F-DCFPyL-PET/CT. Patients were classified attending to: grade group, EAU classification, PSA, PSA doubling time (PSAdt) and PSA velocity (PSAvel). The overall detection rate (DR) and miTNM stage according to PROMISE criteria were assessed for both radiotracers and also correlation (Kappa). The influence of PSA and kinetics on both PET/CT (DR and miTNM) and predictive value of unfavourable kinetics on miTNM were determined. Cut-off PSA, PSAdt and PSAvel values able to predict PET/CT results were determined. Change in miTNM and treatment derived of 18F-DCFPyL information with respect to 18F-Fluorocholine was also evaluated. Results We studied 138 patients. 18F-DCFPyL showed a higher DR than 18F-Fluorocholine (64.5% vs 33.3%). 18F-DCFPyL and 18F-Fluorocholine detected T in 33.3% versus 19.6%, N in 27.5% versus 13.8%, M in 30.4% versus 8.7%. Both tracers DR showed significant associations with PSA and PSAvel. Significant association was only found between miTNM and PSA on 18F-Fluorocholine-PET/CT (p=0.033). For 18F-Fluorocholine and 18F-DCFPyL PET/CT a PSAdt cut-off of 4.09 and 5.59 months, respectively, were able to predict M stage. 18F-DCFPyL changed therapeutic management in 40/138 patients. Conclusion 18F-DCFPyL provides a higher DR and superior miTNM staging than 18F-Fluorocholine in restaging BCR, especially with high PSA and unfavourable PSA kinetics, showing a fair agreement to 18F-Fluorocholine.

With the burgeoning growth of online retail, the issue of counterfeit products has become a significant threat to both consumer trust and brand integrity, posing challenges to sustainable market practices. Online retail platforms are promoted to redesign their channel structures and enhance brand traceability to tackle counterfeits using blockchain technology. To investigate the interactions between blockchain technology and the channel structures of online retail platforms, we design a game theory model incorporating a manufacturer with(out) blockchain participation selling products via an online retail platform that operates an agency channel and/or a reselling channel. We show that the critical trade-off of blockchain participation comprises the brand assurance effect of the blockchain, the channel competition intensification effect, and the blockchain adoption cost. The platform is capable of strategically designing the channel structure to encourage (while discouraging) blockchain participation by the manufacturer. Our analysis highlights the complementarity between blockchain participation and the channel structure. Furthermore, the effect of the consumer’s belief in the reselling channel, the commission fee in the agency channel, and the substitutability between channels are investigated in depth. The research provides valuable insights for online retail platforms and policymakers seeking to foster a sustainable and trustworthy e-commerce ecosystem.

In this paper, we extend the KdVSKR equations in (1+1)-dimension and (2+1)-dimension to fractional KdVSKR equations with modified Riemann-Liouville derivative. The (2+1)-dimensional KdVSKR equation, which is a recent extension of (1+1)-dimensional KdVSKR equation, can model the resonances of solitons in shallow water. By means of the Hirota bilinear method, finite symmetry group method and consistent Riccati expansion method, many new interaction solutions have been derived. Soliton-cnoidal interaction solution of the (1+1)-dimensional fractional KdVSKR equation has been derived for the first time. For the (2+1)-dimensional frac-tional KdVSKR equation, two-wave interaction solutions and three-wave interaction solutions, including dark-soliton-sine interaction solution, bright-soliton-elliptic interaction solution, and lump-hyperbolic-sine interaction solution, have been derived. Impact of the fractional order on the shapes of these solutions has been illustrated by figures. Three-wave interaction solutions of fractional systems have not been reported in the existing references. The research idea in this paper can be applied to other fractional differential equations.

COX II containing a dual core CuA active site is one of the three core subunits of mitochondrial Cco, which plays a significant role in the physiological process. In this report, the full-length cDNA of COXⅡ gene was cloned from Sitophilus zeamais, which had an ORF of 684 bp encoding 227 amino acids residues. The predicted COXⅡ protein had a molecular mass of 26.2 kDa with pI value of 6.37, and multiple sequence alignment and phylogenetic analysis indicated that Sitophilus zeamais COXⅡ had high sequence identity 78.51% with the COXⅡ of other insect species, especially similarity to sitophilus oryzae. This gene was subcloned into the prokaryotic expression vector pET-32a, and induced by IPTG in E.coli Transetta (DE3) expression system. Finally the COXⅡ with 6-His tag was purified using affinity chromatography with Ni²⁺-NTA agarose. WB showed the recombinant COXⅡ was about 44 kD, and the concentration of fusion protein was 50μg/mL. UV-spectrophotometer and infrared spectrometer analysis showed that recombinant COXⅡ could catalyze the oxidation of substrate Cytc, and influenced by AITC. It was found that AITC could form a hydrophobic region with COXⅡ protein via molecular docking, besides, a sulfur atom of AITC structure could form a length of 2.9 Å hydrogen bond with Leu-31. These results will provide valuable information for elucidating the role of COXⅡ in Sitophilus zeamais responses to AITC, meanwhile, it will helpful to carry out a point mutation in AITC binding sites for the future research.

The properties of the annual, semiannual and triennial oscillations (AO, SAO and TO) in the middle atmosphere have been investigated using the TIMED/SABER temperature data. The Lomb-Scargle and wavelet spectra were used to determine the dominant oscillations in the background temperature field. The AO is prominent at the mid-latitudes. The AO amplitudes present an asymmetry between the two Hemispheres, being larger in the mesosphere than in the stratosphere. The SAO dominates the tropical regions, with three amplitude maxima at altitudes of 45, 75, and 85 km. The SAOs in the upper mesosphere (75 km) are out of phase with those in the mesopause (85 km) in the tropical regions, which can generate an enhancement of 11 K at each equinox, contributing to the lower mesospheric inversion layer. The TO is significant in the tropical region, with amplitude being maximum at 35, 45 and 85 km. Result shows that there may be potential interaction by the TO with SAO at 85km at the equator. The relation between ENSO and TO has also been discussed. The ENSO signal may modulate the amplitude of the TO, mainly in the lower stratosphere. The real origin of the TO may lie in the wave-mean-flow interaction.

As the world population grows, fulfilling the need for biomaterials in the healthcare system becomes increasingly important. Biomaterials, which include metals, polymers, ceramics, and composites, play an important role in the creation of medical devices that improve people's lives. The European Society for Biomaterials described biomaterials as non-biological materials used in medical devices to interact with biological systems. This definition has developed to encompass materials that treat, assess, or replace tissues or bodily functions. Biocompatibility, as defined by the FDA, is a key feature of biomaterials, as is the requirement to fulfil design requirements such as mechanical performance, geometry, and electrical control. Over the last decade, advances in regenerative medicine and tissue engineering have boosted biomaterials' usage in medical applications dramatically. Despite its promise, scientists, engineers, and physicians continue to face significant challenges due to the complexity of biomaterials. Biomaterials have various benefits, including biodegradability, non-toxicity, and biocompatibility, making them extremely useful for replacing, sustaining, or improving biological activities in damaged tissues. They are used in a wide range of applications, including tissue engineering implants, human tissue healing and regeneration, medication delivery systems, and biosensors. This study gives insights into the fundamental characteristics, case studies, and ethical issues associated with the usage and use of biomaterials, further examining their potential and significance in healthcare and medicine.

The paper describes the new method for image compression based on coordinated group signal transformation. The algorithm is a type of difference coding. Coordinated processing significantly simplifies the difference signal conversion scheme using a single group codec for all signals. The described method considers color channels as correlated signals of a multi-channel communication system. The specifics of the processed data required modification of the coordinated group processing algorithm. First, we changed how to calculate the difference signals to prevent data loss. Secondly, the group codec was supplemented with a neural network to improve the quality of reconstructed images. We considered the following types of neural networks: fully connected, recurrent, convolution, and convolution in the Fourier space. Based on the simulation results, it is best to use fully connected neural networks if the goal is to minimize processing delay time. These networks have a response time of 13 ms. On the other hand, if the priority is to improve quality in cases where delays are not critical, then convolution neural networks in the Fourier space should be used. These networks have a response time of 140 ms and are of significant interest.

There is an increasing need for effective anxiety and pain reduction during medical imaging procedures in children. This is a complex issue, addressed by both non-pharmacological or pharmacological approaches. Dexmedetomidine is a fairly recently marketed, selective α2-adrenergic agonist, and can be administered intranasally. To develop an evidence-guided clinical protocol, we investigated its (side)-effects, preconditions and safety aspects following intranasal dexmedetomidine in children (1 month-5 years) for procedural sedation during medical imaging. To do so, a systematic search (PubMed, Embase, CINAHL (12/2021)) was performed to identify clinical studies on intranasal dexmedetomidine for procedural sedation for medical imaging (Computer Tomography, Magnetic Resonance Imaging). Following screening and quality assessment, 8 studies were retained. Nasal nebulization was considered the best administration method, dosing varied between 2 to 4 µg/kg (age-dependent) 30-45 minutes prior to imaging, and contra-indications or restrictions on oral intake were somewhat consistent across studies. Valid sedation scores were routinely used to assess sedation and the need for rescue dosing, while discharge was generally based on the Aldrete score (score ≥9). Heart rate, blood pressure and saturation were routinely monitored, with commonly observed bradycardia or hypotension (decrease by 20%). Based on these findings, a roadmap for evidence-guided clinical protocol was generated.

In electromagnetic ultrasonic testing, it is difficult to recognize small-size bottom cracks by time of flight (ToF), and the lift-off fluctuation of the probe affects the accuracy and consistency of the inspection results. In order to overcome the difficulty, a novel EMAT (electromagnetic acoustic transducer)-PEC (pulse eddy current) composite sensor is designed. We use amplitude of bottom echo recorded by EMAT to identify the tiny bottom crack as well as the amplitude of PEC signals picked up by the integrated symmetric coils to measure the average lift-off of the probe in real time. Firstly, the effects of lift-off and bottom cracks on amplitude of bottom echo are distinguished combining the theoretical analysis and finite element method (FEM). And then an amplitude correction method based on the fusion of EMAT and PEC signals is proposed to reduce the impact of lift-off on the defect signal. The experimental results demonstrate that the designed composite sensor can effectively detect the bottom crack as small as 0.1mm* 0.3mm. The signal fusion method can accurately correct the amplitude of defect signal and the relative error is less than ±8%.

The studied solar pot is a recent invention, which gained a utility model protection in 2021 from the Hungarian Intellectual Property Office under patent number 5489. The device is made for environmentally friendly cooking or heating (by utilizing solar energy) of foods and liquids. Its structure is similar to a double pipe heat exchanger, it has an outer mantle and an inner cooking tank. The goals of the paper are proposing a new physically-based mathematical model describing the solar pot and carrying out computer experiments with it, assembling an experimental system of the pot connected with a solar collector and performing measurements on it. Based on the results, the solar pot can successfully be used for cooking or sterilizing foods or liquids during the studied time period, in Hungary.

The research reported on this paper was aimed at improving the overall efficiency of a PDO certified artisanal cheese production process. Being a PDO certified foodstuff by the EU, it is considered to have properties and qualities determined by the geographical environment in which is made, with its production taking place in a specific and determined geographical location, in this case the Serra da Estrela region. In that sense, the authors conducted a mapping according to a systemic perspective of the processes involved in the context of manufacturing and distribution of certified Serra da Estrela cheese. Numerous methods were used throughout the process, such as a systemic design analysis, and techniques derived from ethnographic methods, which led to the collection of data in the field and consequently provided the immersion of the researcher in genuine work situations. Critical points were identified and emphasized in the systemic map with the purpose of encouraging initiatives to address and overcome the gaps and inefficiencies detected. The systemic design analysis triggered the development of design work. Observations following an ethnographic approach identified ergonomic risks in cheese making during the process of cutting excess chips, fostering the emergence of musculoskeletal disorders at the wrist. A tool that fits best to the task at hand was developed. A prototype of the new tool enabled collecting feedback from use in the work context, in order to inform product development. The domains of agricultural production and microbiology, considering the specific microorganisms developed trough the ripening process of the cheese, turned out to be aspects of high importance for the issue under focus, contributing to a broader understanding of the ripening process and its risks, simultaneously improving the efficiency and success of cheese production. If it were not for the systemic analysis, which served as a link between the boundaries of distinct domains such as the risk of microorganism contamination, ergonomics, energy efficiency, legislation and regulation policies, transportation challenges and economic viability, approached throughout the research. Simultaneously creating bridges between them, the various problems might not have been detected in the first place, as they are usually addressed in specialized disciplines, predetermined by the restrictions of each specific area of knowledge. As a consequence of the development of this research, which was based on an analysis that sought to establish possible connections between various disciplines and tried to constantly maintain a holistic perspective, making new connections and observing the issues from a new angle, apart from the already established methodologies. All this allowed to lay out the seeds for the development of a plan to tackle the critical points identified by the systemic analysis reported in this paper.

Abstract: Transcription factors are crucial pre-transcriptional regulatory mechanisms that can modulate the expression of downstream genes by binding to their promoter regions. DOF (DNA binding with One Finger) proteins are a unique class of transcription factors with extensive roles in plant growth and development. Our previous research indicated a decrease in iron content in chlorotic bamboo leaves. However, to our knowledge, genes related to iron metabolism pathways in bamboo species have not yet been studied. Therefore, in the current study, we identified iron metabolism-related (IMR) genes in bamboo and determined the transcription factors that significantly influence them. Among these, DOFs were found to have widespread effects and potentially significant impacts on their expression. We identified specific DOF members in Dendrocalamus latiflorus with binding abilities through homology with Arabidopsis DOF proteins, and established connections between some of these members and IMR genes using RNA-seq data. Additionally, molecular docking confirmed the binding interactions between these DlDOFs and the DOF binding sites in the promoter regions of IMR genes. The co-expression relationship between the two gene sets was further validated using q-PCR experiments. This study paves the way for research into iron metabolism pathways in bamboo and lays the foundation for understanding the role of DOF transcription factors in D. latiflorus.

This paper is focused on typical rural settlements in the Stara Planina Mountain area in Serbia. They are distinguished by their authenticity, identity and character, and they have still not been destroyed by inappropriate development as is the case in some other mountain areas in Serbia, where the effects of urbanization, globalization and homogenization are obvious. Consequently, there is a need to prevent these effects in mountain areas where there is a threat of disbalance between development and the inherited natural and cultural values. The paper starts from several important concepts that relate contemporary approaches to cultural heritage preservation, place morphology and planning future development. The concept definitions from recent documents from related fields are used. These concepts are then applied to the area of Stara Planina Mountain and its rural settlements. The necessity for an integrative approach to planning this area with significant natural and anthropogenic potential is pointed out, including its integration into international programs of sustainable development.

Skin inflammation associated with chronic diseases has the direct action of keratinocytes in its immunopathogenesis, leading to a series of immune responses. However, there are still no highly targeted treatments, and the development of more specific therapies is highly desirable. In the present work, nanocapsules containing quinizarin (QZ/NC) were developed, evaluating their act in a model of the keratinocytes inflammatory process in vitro with the action of Photodynamic Therapy, analyzing the permeation in a 3D skin model. Physicochemical, stability, cytotoxicity and permeation analyses of the nanomaterials were carried out. The nanocapsules showed desirable physicochemical characteristics and were stable during the analysis period, without spectroscopic modifications. The cell viability test carried out showed no cytotoxicity at the lowest QZ/NC concentrations. The permeation and cellular uptake studies showed the permeation of QZ/NC in 3D skin models and the intracellular incorporation and internalization of the drug, enhancing its action in the drug delivery technique. Promising results were presented using the model developed to induce the inflammatory process in vitro and applying the synthesized nanomaterial in conjunction with PDT, where a decrease in the levels of cytokines analyzed was observed, representing a possible new therapeutic approach for inflammatory skin diseases.