In order to study the effect of explosion load on the flexural performance of RC beams, two RC beams of the same size were carried out explosion test and bearing capacity test successively. Piezoelectric intelligent aggregate was embedded in the beams in advance to monitor the damage state of the beams, which realized the whole process of damage monitoring of the concrete inside the structure from explosion damage to compression damage.Based on wavelet packet analysis and residual bearing capacity damage evaluation criteria, the beam damage was quantitatively evaluated, and the bending bearing capacity of RC beam after explosion damage was compared and analyzed.The results show that the change of concrete strain gauge signal, the phenomenon of crack development and the increase of internal crack development index indicate that the RC beam is damaged by explosion load.After explosion damage, the damage index of the beam increases and the residual bending capacity decreases, which proves that the piezoelectric intelligent aggregate sensor can effectively monitor the bending capacity change of the component after explosion damage.

Structural health monitoring has been studied by a number of researchers as well as various industries to keep up with the increasing demand for preventive maintenance routines. This work presents a novel method for reconstruct prompt, informed strain/stress responses at the hot spots of the structures based on strain measurements at remote locations. The structural responses measured from usage monitoring system at available locations are decomposed into modal responses using empirical mode decomposition. Transformation equations based on finite element modeling are derived to extrapolate the modal responses from the measured locations to critical locations where direct sensor measurements are not available. Then, two numerical examples (a two-span beam and a 19956-degree of freedom simplified airfoil) are used to demonstrate the overall reconstruction method. Finally, the present work investigates the effectiveness and accuracy of the method through a set of experiments conducted on an aluminium alloy cantilever beam commonly used in air vehicle and spacecraft. The experiments collect the vibration strain signals of the beam via optical fiber sensors. Reconstruction results are compared with theoretical solutions and a detailed error analysis is also provided.

Marine renewable energy is emerging as one of the fast-growing industry in the last decades, as modern society pushes for technologies that can convert energy contained from winds, waves, tides and stream flows. The implementation of renewable energy technologies impose high demands on both structural and environmental engineering, as the energy converters have to work under extreme conditions where parameters such as sea-bottom configuration, water transparency and depth, sea-states and prevailing winds are harsh. Constant monitoring of the marine environment is crucial in order to keep this sector reliable. Active acoustics is becoming a standard tool to collect multi-dimensional data from physical, geological and biological properties of the marine environment. The Div. of Electricity of Uppsala University have been developing an environmental monitoring platform based on sonar (Sound Navigation And Raging) systems. This platform aims to monitor the installation, operation and decommissioning of marine renewable energy converters. The focus will be given the observations of behaviours of marine animals in vicinity of energy converters but also structural inspection and monitoring of MRETs. This paper describes how this multifunctional environmental monitoring platform come to existence from the design to the deployment phase.

Quick and appropriate diagnostics and the use of intraoperative monitoring (IM) of hearing during vestibular schwannoma (VS) resection increase the likelihood of hearing preservation. During surgery, various methods of IM can be used, i.e. auditory brainstem responses (ABR), transtympanic electrocochleography (TT-ECochG) and direct cochlear nerve action potentials. The aim of the study was to evaluate the prognostic values of IM of hearing using ABR and TT-ECochG in predicting postoperative hearing preservation, as well as to evaluate relationships between them during various stages of surgery. This retrospective study presents the pre- and postoperative audiological test results and IM of hearing records (TT-ECochG and ABR) in 75 (43 women, 32 men, aged 18-69) patients with diagnosed VS. The preoperative pure tone average hearing threshold was 25.02 dB HL, while after VS resection it worsened on average by 30.03 dB HL. According to the American Academy of Otolaryngology-Head and Neck Surgery (AAO-HNS) Hearing Classification, before and after (pre/post) the surgery, there were 47/24 patients in hearing class A, 9/8-B, 2/1-C, and 17/42-D. In speech audiometry, the average preoperative speech discrimination score at an intensity of 60 dB SPL was 70.93%, and after VS resection it worsened to 38.93%. The analysis of electrophysiological tests showed that before the tumor removal the I-V ABR interlatencies was 5.06 ms, and after VS resection it was 6.43 ms. The study revealed correlations between worse postoperative hearing and changes in intraoperatively measured ABR and TT-ECochG. IM of hearing is very useful in predicting postoperative hearing in VS patients and increases the chance of postoperative hearing preservation in these patients.

Water stable proteins may offer a new field of applications in smart materials for buildings and infrastructures where hydraulic reactions are involved. In this study, cement mortars modified through water-soluble silk fibroin (SF) are proposed. Water-soluble SF obtained by redissolving SF films in phosphate buffer solution (PBS) showed the formation of a gel with β-sheet features of silk II. Electrical measurements on SF indicate that calcium ions are primarily involved in the conductivity mechanism. By exploiting the water solubility properties of silk II and Ca2+ ion transport phenomena and its trapping effect over water molecules, SF provides piezoresistive and piezocapacitive properties to cement mortars, thus enabling self-sensing of mechanical strain which is quite attractive in structural health monitoring applications. SF/cement-based composite introduces the capacitive gauge factor that surpasses the traditional resistive gauge factor reported in the literature by threefold. Cyclic voltammetry measurements demonstrated SF cement mortars possess memcapacitive behavior for positive potentials around +5 V, attributed to an interfacial charge build-up modulated by the SF concentration and the working electrode. Electrical square-biphasic excitation combined with cyclic compressive loads revealed memristive behavior during the unloading stages. These findings along with the availability and the sustainability of SF pave the way for the design of novel multifunctional materials, particularly for applications in masonry and concrete structures.

We are living in a world where people always strive for the luxuries they can get with less hard work and for these smart systems are developed and established all over the world to make life easier for the people. However, in Pakistan being a third-world country we are unable to achieve better results due to the lack of proper transit from one area to another. Sometimes the roads are not in their optimum conditions and hence people have to face a lot of problems while traveling. In urban areas, people cannot reach their destination in time, in some cases, they damage their vehicles due to the cracks on the roads, in medical emergency patient dies most of the time in their transit from rescuing point to the hospital. Similarly, in rural areas where farmers face countless problems while bringing their yield of the season towards the markets. Therefore, having described the severe damage the bad quality of roads is making. A solution is proposed to solve the problems of both the rural and urban population in our project. The project aims to provide the solution to their problem to a certain extent by monitoring the conditions of the roads. The sensors in the system will calculate the values and send them to the cloud server. The cloud server used is the blynk platform where the data will be stored. Moreover, data can be provided to the government in the future for the timely maintenance of the roads, and hence the citizens and lifestyle of the people will be changed. It is expected that the problems of both urban and rural population will be solved to a greater percentage.

Carbon capture and storage has gotten increased attention during the last decade, and several full-scale projects are currently being planned. This requires transportation of large quantities of CO2 from the capturing plant to the end point. From economic and public acceptance point of view it is important to ensure that the transportation system is operated in a safe manner. Thus, avoiding threats like corrosion or formation of particles are important. It is therefore required to monitor that the transported CO2 fulfils the required specifications, and in practice this means that the impurity content of the CO2 must be analysed. CO2 will in most cases be transported in the liquid or supercritical state (high pressure), which makes the practicalities around chemical analysis more difficult. Phase transition from liquid or supercritical state to gaseous state may also introduce several physiochemical effects that may affect the analysis. This paper discusses technical and practical challenges with such types of analysis. Most of this work is based on experience that was gained during development of analytical system for dense phase CO2 in a joint industry project that studied corrosion and chemical reactions in a simulated CO2 transport system.

Background: Monitoring the mobility of players during wheelchair sports is essential to support coaches in their understanding of the activity and in their training programming. However, the amount of information available from the monitoring tools, combined with a general approach to processing and a poor presentation of the data to the coaches, is not effective and remains unused. Thus, this study aimed to propose a simple and efficient algorithm for identifying locomotor tasks (static, forward/backward propulsion, pivot/tight/wide rotation) during wheelchair movements based on wheelchair kinematic data. Methods: A total of 36 wheelchair tennis and badminton players participated, completing at least one of three proposed tests: the star test, the figure-of-eight test, and the forward-backward test. Locomotor tasks were identified using a five steps procedure including data reduction, symbolic approximation and pattern logical search. Results: Using this method, 99% of locomotor tasks were properly identified for the star test, 95% for the figure-of-eight test and 100% for the forward-backward test. Conclusion: This method appears to be a valuable tool for a simple and clear identification and representation of locomotor tasks over extended periods of time. Future research should aim at applying this method to multiple wheelchair court sports matches or daily life declination.

The Fruit Harvest Helper, a mobile application developed by Northwest Nazarene University’s (NNU) Robotics Vision Lab, aims to assist farmers in estimating fruit yield for apple orchards. Currently, farmers manually estimate the fruit yield for an orchard, which is a laborious task. Fruit Harvest Helper seeks to simplify their process. While prior research efforts at NNU concentrated on developing an iOS app for blossom detection, this current research aims to adapt that smart farming application for apple detection across multiple platforms, iOS and Android. The old and new applications were designed with an intuitive user interface that is easy for farmers to use, allowing for quick image selection and processing. Unlike before, the adapted app utilizes a color ratio-based image segmentation algorithm implemented in OpenCV C++ to detect apples in apple tree images selected for processing. The results of testing the algorithm with a dataset of images indicate an 8.52% Mean Absolute Percentage Error (MAPE) and a Pearson correlation coefficient of 0.6 between detected and actual apples on the trees. These findings were obtained by evaluating the images from both the east and west sides of the trees, which was the best method to reduce the error of this algorithm. Although the Fruit Harvest Helper shows promise, there are many opportunities for improvement. These opportunities include exploring alternative machine-learning approaches for apple detection, conducting real-world testing without any human assistance, and expanding the app to detect various types of fruit. The Fruit Harvest Helper mobile application is among the many mobile applications contributing to precision agriculture, nearing readiness for farmers to use in yield monitoring and farm management.

The Hindu Kush Himalaya (HKH) is one of the most flood-prone regions in the world, yet heavy cloud cover and limited in-situ observations have hampered efforts to monitor the impact of heavy rainfall, flooding, and inundation during severe weather events. This paper introduces HydroSAR, a Sentinel-1 SAR-based hazard monitoring service that was co-developed with in-region partners to provide year-round, low-latency weather-hazards information across the HKH. The paper describes the end-user focused concept and overall design of the HydroSAR service. It introduces the main processing algorithms behind HydroSAR’s broad product portfolio, which includes qualitative visual layers as well as quantitative products measuring surface water extent and water depth. We summarize the cloud-based implementation of the developed service, which is providing capability to scale automatically with event size. A performance assessment of our quantitative algorithms is described, demonstrating capabilities to map flood extent and water depth at an accuracy of >90% and

Flexible humidity sensors (FHS) with fast response and durability to high-humidity environment are highly desirable for practical applications. Herein, an FHS based on crosslinked sodium alginate (SA) and MXene was fabricated, which exhibited high sensitivity (impedance varied from 107 to 105 Ω between 10% and 90% RH), good selectivity, prompt response (response/recover time of 4 s/11 s), high sensing linearity (R2 = 0.992) on a semi-logarithmic scale, relatively small hysteresis (~5% RH), good repeatability, and good resistance to high humid environment (negligible change in sensing properties after placed in 98% RH over 24 h). It is proposed that the formation of crosslinking structure of SA and introduction of MXene with good conductivity and high specific surface area contributed to the high performance of the composite FHS. Moreover, the FHS could promptly differentiate respiration status, recognize speech and measure fingertip movement, indicating potentials in breath monitoring and non-contact human-machine interactions. This work provides guidance for developing advanced flexible sensors with wide application scope in wearable electronics.

This study demonstrates the efficacy of structured pruning and architectural fine-tuning on the YOLOv7-tiny model for eye state detection, emphasizing optimization for real-time applications. Structured pruning significantly reduced the model's complexity and storage size while maintaining high detection accuracy, as evidenced by stable precision, recall, and mAP@.5 metrics across iterations. Further fine-tuning adjusted the model's width and depth, optimizing efficiency and processing speed without compromising performance. These optimizations yielded YOLOv7-tiny variants that are both computationally efficient and accurate, suitable for resource-constrained environments. The findings highlight the critical role of model optimization in deploying effective neural networks for specific detection tasks in real-time scenarios.

Drought stress severely affects the normal growth and development of wheat, leading to reduced yields and quality. To address the lag and limitations of traditional drought monitoring methods, this paper proposes a drought stress monitoring model for winter wheat during critical growth stages based on deep learning. By acquiring drought stress images of winter wheat during three critical growth stages: rise-jointing, heading-flowering and flowering-maturity, a dataset correlating these images with soil moisture monitoring data was established. The DenseNet121 network model was selected as the base network to extract phenotypic features of winter wheat under drought stress. Variables such as the model's training approach, changes in learning rate, and whether an attention mechanism was included, were used to conduct eight sets of model training and optimization strategy experiments. A drought stress monitoring model for winter wheat during critical growth stages based on an improved DenseNet-121 was constructed. The results showed that the average recognition accuracy of the eighth group in the test set reached 94.67%, indicating good application prospects in the recognition of drought stress levels during critical growth stages of wheat.

The integration of Artificial Intelligence (AI) and the Internet of Things (IoT) in healthcare is transforming chronic disease management and pandemic response, particularly for vulnerable populations such as the elderly and those with multiple chronic conditions. This review systematically examines the current applications of AI and IoT technologies in managing chronic diseases like diabetes, cardiovascular disease, and chronic obstructive pulmonary disease (COPD), alongside their role in enhancing healthcare response during the COVID-19 pandemic. Key findings demonstrate significant improvements in patient outcomes, including enhanced glycemic control in diabetes management, early detection of cardiovascular anomalies, and a reduction in hospital admissions for chronic disease patients through AI-enabled remote monitoring. Despite these advancements, challenges remain, including data security, algorithmic bias, and the high cost of implementing AI and IoT systems. This review explores future directions for overcoming these obstacles, emphasizing the potential of multi-dimensional data integration, real-time predictive analytics, and personalized AI models to further revolutionize healthcare. Additionally, the accompanying Graphic Abstract visually illustrates how AI-driven insights, generated from IoT-enabled devices, are transforming healthcare delivery by facilitating real-time monitoring, personalized interventions, and proactive patient care. The article concludes with recommendations for addressing the technological, ethical, and regulatory challenges that must be overcome to fully realize the potential of AI and IoT in healthcare.

Early diagnosis of paroxysmal atrial fibrillation (PAF) could suggest patients to receive timely interventions in clinical practice. Various PAF onset prediction algorithms might benefit from accurate heart rate variability (HRV) analysis and machine learning classification but to be challenged in real-time monitoring scenarios. The aim of this study is to present an end-to-end deep learning based PAFNet model that integrates a sliding window technique on raw R-R interval of electrocardiogram (ECG) segments to achieve a real-time prediction of PAF onsets. This integration enable the deep convolutional neural network (CNN) to be customized as a light-weight architecture that accommodates the size of sliding windows simply by altering the input layer, specifically its effectiveness in making a new prediction with each new heartbeat. Catering to potential influence of input sizes, three CNN models were trained using 50, 100, and 200 R-R intervals, respectively. For each model, the performance of automated algorithms was evaluated for PAF prediction using a ten-fold cross-validation. As a results, a total of 56,381 PAFN-type and 56,900 N-type R-R interval segments was collected from publicly accessible ECG databases, and a promising prediction performance of the automated algorithm with a 100 R-R intervals was achieved in terms of the sensitivity of 97.12%, the specificity of 97.77%, and the accuracy of 97.45%, respectively. Importantly, the automated algorithm with a sliding windows step of 1 could process one sample in only 23.1 milliseconds and identify the onset of PAF at least 45 minutes in advance. The present results suggest that the sliding window technique on raw R-R interval sequences along by deep learning based algorithms may offers the possibility of providing an accurate, real-time, and end-to-end clinical tool for mass monitoring of PAF.

Environmental monitoring plays a central role in diagnosing climate and management impacts on natural and agricultural systems, enhancing the understanding hydrological processes, optimizing the allocation and distribution of water resources, and assessing, forecasting and even preventing natural disasters. Nowadays, most monitoring and data collection systems are based upon a combination of ground-based measurements, manned airborne sensors or satellite observations. These data are utilized in describing both small and large scale processes, but have spatiotemporal constraints inherent to each respective collection system. Bridging the unique spatial and temporal divides that limit current monitoring platforms is key to improving our understanding of environmental systems. In this context, Unmanned Aerial Systems (UAS) have considerable potential to radically evolve environmental monitoring. UAS-mounted sensors offer an extraordinary opportunity to bridge the existing gap between field observations and traditional air- and space-borne remote sensing, by providing not just high spatial detail over relatively large areas in a cost-effective way, but as importantly providing an entirely new capacity for enhanced temporal retrieval. As well as showcasing recent advances in the field, there is also a need to identify and understand the potential limitations of UAS technology. For these platforms to reach their monitoring potential, a wide spectrum of unresolved issues and applications specific challenges require focused community attention. Indeed, to leverage the full potential of UAS-based approaches, sensing technologies, measurement protocols, post-processing techniques, retrieval algorithms and evaluations techniques need to be harmonized. The aim of this paper is to provide a comprehensive general overview of the existing research on studies and applications of UAS in environmental monitoring in order to suggest users and researchers on future research directions, applications, developments and challenges.

Transition zones are in the places on the track, with a change in the basic composition of the railway body. There are many sections with a sudden change in the stiffness of the structures built. When the trains are running, a longitudinal shock wave is created from the wheels, which hits these building objects with a higher stiffness and deforms the surroundings of these zones. The greatest attention should be paid mainly to the transition points from the fixed track to the classic track with a track bed, including objects of the railway substructure such as bridges, portals of tunnels, etc. As part of the research sections on the main corridor lines, a long-term inspection and monitoring was carried out with a continuous measurement system using the KRAB trolley. Height changes in the deflections of rails are evidence of their behavior. The measurements took place on a fixed track and a track with a ballast. Changes in the height jumps between the fixed railway track and the track with a gravel bed are significant and have been recorded since the tracks were put into operation. These certain height deflections allow designers to develop new, more durable construction designs.

Background: Critical states present scale-free dynamics, optimizing neuronal complexity. We explored electroencephalogram (EEG) criticality in amnesic Mild Cognitive Impairment (aMCI) patients with clinical improvement in working memory, verbal memory, verbal fluency and overall executive functions after the completion of a 6-month prospective memory training. (2) Methods: We compared “before” and “after” stationary resting-state EEG records of right-handed MCI patients (n = 17; 11 females), using the method of critical fluctuations and Haar wavelet analysis. (3) Results: Significant criticality enhancement was present in frontotemporal electrodes [mean dif: 0.10; Z = 7, p = .019] and isolated electrodes T6 [mean dif: 0.204; t (10) = - 2.3, p = .044] and F4 [mean dif: 0.0194; t (10) = - 2.82; p = .018]. (4) Conclusions: EEG criticality agreed with clinical improvement, consisting a possible monitoring biomarker in MCI and Alzheimer’s disease. Further evaluation is needed in patients under cognitive training or even drug-modifying therapies.

Conventional approaches in Structural Health Monitoring (SHM) tend to be complex, destructive, and time-intensive. Additionally, they often require a large number of sensors to thoroughly assess structural integrity. In this study, we present a novel, non-destructive SHM framework based on machine learning (ML) for the accurate detection and localization of structural cracks. This approach leverages a minimal number of strain gauge sensors linked via Bluetooth communication. The framework is validated through empirical data collected from 3D carbon fiber-reinforced composites, including three distinct specimens, ranging from crack-free samples to specimens with up to ten cracks of varying lengths and depths. Strain data from five sensors were analyzed using a combination of Shewhart charts, Grubbs Test (GT), and a hierarchical clustering algorithm, specifically designed to evaluate and classify fractures. Our ML-based framework offers a streamlined and efficient alternative to traditional laboratory procedures, delivering precise crack detection with significant potential for applications in the composites industry.

We present an autonomous system that remotely monitors the state of reinforced concrete structures. This system performs the real-time follow-up of the corrosion rate of rebars (iCORR), along with other relevant parameters, such as temperature, corrosion potential (ECORR) and electrical resistance of concrete (RE), at many of structures’ control points by using embedded sensors. Its corrosion sensor is stressed, to which a novel electrochemical polarization technique is applied. The custom electronic system manages the sensor network, consisting of a measurement board per control point connected to a central single-board computer in charge of processing measurement data and uploading results to a server via 4G connection. In this work, we report the results obtained after implementing the sensor system into a reinforced concrete wall, where two well-differentiated representative areas were monitored. The obtained corrosion parameters showed consistent values. Similar conclusions are obtained with ECORR recorded in rebars. With the iCORR follow-up the corrosion penetration damage diagram is built. This diagram is particularly useful for identifying critical events during the corrosion propagation period and to be able to estimate structures’ service life. Hence the system is presented as a useful tool for the structural maintenance and service life predictions of new structures.

Warming of the climate system is unequivocal, and many of the observed changes are unprecedented over five decades to millennia. Globally the atmosphere and ocean is increasingly getting warmer, the amount of ice on the earth is decreasing over the oceans, and the sea level has risen. According to Intergovernmental Panel on Climate Change, the total increasing temperature globally averaged combined land and surface between the average of the 1850-1900 period and the 2003 to 2012 period is 0.78 °C (0.72 to 0.85). But should we prepare for such the relatively small change? The importance is not the mean of the warming but the considerable likelihood of climate change that could trigger extreme natural hazards. The impact and the risk of climate change associated with railway infrastructure have not been fully addressed in the literature due to the difference in local environmental parameters. On the other hand, the current railway network in Malaysia, over the last decade, has been significantly affected by severe weather conditions such as rainfall, lightning, wind and very high temperatures. Our research findings point out the extremes that can lead to asset system failure, degraded operation and ultimately, delays to train services. During the period of flood, the embankment of the track can be swept away and bridge can be demolished, while during drought, the embankment of the track can suffer from soil desiccation and embankment deterioration, high temperature increases the risk of track buckling and high winds can result in vegetation or foreign object incursion on to the infrastructure as well as additional quasi-static burden exerted. This review is of significant importance for planning and design of the newly proposed high speed rail link between Malaysia and Singapore.

The state-of-the-art smart city has been calling for an economic but efficient energy management over large-scale network, especially for the electric power system. It is a critical issue to monitor, analyze and control electric loads of all users in system. In this paper, we employ the popular computer vision techniques of AI to design a non-intrusive load monitoring method for smart electric energy management. First of all, we utilize both signal transforms (including wavelet transform and discrete Fourier transform) and Gramian Angular Field (GAF) methods to map one-dimensional current signals onto two-dimensional color feature images. Second, we propose to recognize all electric loads from color feature images using a deep neural network with multi-scale feature extraction and attention mechanism. Third, we design our method as a cloud-based, non-intrusive monitoring of all users, thereby saving energy cost during electric power system control. Experimental results on both public and our private datasets have demonstrated our method achieves superior performances than its peers, and thus supports efficient energy management over large-scale Internet of Things.

Bearing component damage contributes significantly to rotating machinery failures. It is vital for the rotor-bearing system to be in good condition to ensure proper functioning of the machine. Over recent decades, extensive research has been devoted to the condition monitoring of rotational machinery, with a particular focus on bearing health. This paper provides a comprehensive literature review of recent advancements in intelligent condition monitoring technologies for rolling element bearings. Fundamental monitoring strategies are introduced, covering various sensing, signal processing, and feature extraction techniques for detecting defects in rolling element bearings. While vibration-based monitoring remains prevalent, alternative sensor types are also explored, offering complementary diagnostic capabilities or detecting different defect types compared to accelerometers alone. Signal processing and feature extraction techniques, including time domain, frequency domain, and time-frequency domain analysis, are discussed for their ability to provide diverse perspectives for signal representation, revealing unique insights relevant to condition monitoring. Special attention is given to information fusion methodologies and the application of intelligent algorithms. Multisensor systems, whether homogeneous or heterogeneous, integrated with information fusion techniques, hold promise in enhancing accuracy and reliability by overcoming limitations associated with single sensor monitoring. Furthermore, the adoption of AI techniques, such as machine learning and metaheuristic optimisation, has led to significant advancements in condition monitoring, yielding successful outcomes in various studies. Finally, avenues for further advancements to improve monitoring accuracy and reliability are identified, offering insights into future research directions.

A platform for indoor monitoring inside buildings, integrating both conventional and environmentally friendly devices with energy-harvesting sources, is proposed. Biomaterials such as gelatin and chitosan, derived from renewable resources, have been utilized to fabricate hydrogel and active layers for sensors and supercapacitors. These devices enhance the environmental profile of the proposed solution by employing sustainable materials and optimizing energy consumption. The developed electronic board prototype provides a versatile platform for testing various sensor configurations while accommodating different energy-harvesting sources. The article details the design of an energy harvesting system for indoor monitoring, covering various aspects regarding energy sources, power management circuits, and low-power microcontroller units. It examines energy storage devices and sensors, including both eco-friendly and commercial ones, as well as radio transceivers with different communication technologies. Additionally, an energy analysis to evaluate the performance and energy efficiency of the platform is presented.

There are considerable benefits in applying Artificial Intelligence to automation in modern industries including Oil and Gas Industries. Oil and Gas Industries have many complex systems in their production and flow line. The failure of gas equipment will have serious consequences including financial and environmental issues. Condition monitoring of oil and gas equipment provides the condition of components, machines, systems, equipment, data hardware, and even software. The predictive maintenance and industry 4.0 applications have more advantages in petrochemical industries to make a safer economic environment and this paper addresses the Artificial Intelligence (AI) application of condition monitoring for Oil and Gas Industries. To understand the effectiveness of AI in condition monitoring for oil and gas industries, a case study related to the condition monitoring of drilling machine is conducted and applied Artificial Neural Network (ANN) algorithm to analyze and predict the potential failures. The novelty of this work is the proposal of an approach for tool wear monitoring in drilling using acoustic emission sensors for feature extraction and considering wavelet packet decomposition for further analysis. The extracted features from WPD are given as input for ANN to identify the healthiness of the drill bit and machine. This work aims to find the effectiveness of AI-based condition monitoring in enhancing effectiveness of monitoring and the safety of equipment in Oil and Gas Industries.

This paper introduces a novel respiratory detection system based on diaphragm wall motion tracking using an embedded ultrasound sensory system. We assess the utility and accuracy of this method in evaluating diaphragmatic function and its contribution to respiratory workload. The developed system is able to monitor the diaphragm wall activities when the sensor is placed in the zone of apposition (ZOA). This system allows the direct measurements with only one ultrasound PZT5 piezo transducer. The system both generates pulsed ultrasound waves at 2.2 MHz and amplifies reflected echoes. According to the diaphragmatic motions, the respiratory signals of the proposed system is insensitive to human motion artifacts. Promising results were obtained from six subjects on six different tests with an average sensitivity and specificity of 84% and 93% of respiration detection, respectively. Measurements are referenced to a SPR-BTA commercial spirometer. In this study, we also evaluated inertial and photoplethysmography (PPG) sensors as other conventional methods in this area.

This paper details the comprehensive activities conducted in a laboratory setting to assess the Structural Health Monitoring (SHM) of prefabricated building envelopes. Aimed at enhancing the structural evaluation of buildings, the focus of this research lies in employing nondestructive sensors for SHM with the objective to advance in the understanding and assessment of facade conditions. The paper outlines the methodologies employed, starting with a modal analysis to define the structural vibration's modal frequency. Subsequently, tests were defined and executed to validate building envelope compliance in case of stress typical of high-rise building. Throughout these tests, continuous monitoring of the façade was conducted using both conventional (accelerometers, extensimeter washers) and non-conventional sensors (Fiber Optic Sensing) The gathered data underwent thorough processing and analysis to provide an overall perspective on the structure's behavior during the stress test. The investigation aimed to identify whether specific physical phenomena correlate with distinct signals and to evaluate if continuous façade monitoring over the building's lifespan aids in preventing potential structural damage. Moreover, two modal analyses were conducted to compare final data and frequencies with earlier data, enabling the detection of any structural alterations. The results from compliance testing and structural analysis yielded noteworthy insights contributing to the evolving field of structural health monitoring, offering valuable findings that advance our ability to proactively manage and maintain the integrity of building structures.

This paper experimentally reveals some of the resources offered by the evolution of the instantaneous active electric power in describing the state of three-phase AC induction asynchronous electric motors (with squirrel-cage rotor) operating under no-load conditions. A mechanical power is required to rotate the rotor at no-load and this mechanical power is satisfactorily reflected in the constant and variable part of instantaneous active electric power. The variable part of this electrical power should necessarily have a periodic component with the same period as the period of rotation of the rotor. The paper proposes a procedure for extracting this periodic component description (as a pattern, by means of a selective averaging of instantaneous active electrical power) and analysis. The time origin of this pattern is defined by the time of a selected first passage through the origin of an angular marker placed on the rotor, detectable by a proximity sensor (e.g. a laser sensor). The usefulness of the pattern in describing the state of the motor rotor has been demonstrated by several simple experiments which show that a slight change in the no-load running conditions of the motor (e.g. by placing a dynamically unbalanced mass on the rotor) has clear effects in changing the shape of the pattern.

For monitoring of chimeric antigen receptor (CAR) T-cell therapies antigen-based CAR detection methods are usually applied. However, for each target-antigen a separate detection system is required. Furthermore, when monitoring CAR T-cells in the blood of patients treated with bispecific antibodies or T-cell engagers (bsAbs/BiTEs) recognize the same antigen, these methods producing false-positive results in clinical diagnostics. Anti-CAR-linker monoclonal antibodies (mAbs) targeting the linker sequence between the variable domains of the antigen binding CAR fragment, promise an universal and unbiased CAR detection. To test this, we analyzed clinical specimens of all BCMA- and CD19 targeting CAR T-cell products currently approved for clinical use. We found a highly specific and sensitive CAR detection by using anti-CAR-linker mAb in blood cells from patients treated with Ide-cel, Tisa-cel, Axi-cel, Brexu-cel, and Liso-cel. For Ide-cel and Tisa-cel the sensitivity was significant lower compared to antigen-based CAR detection assays. Strikingly, the specificity of anti-CAR linker mAb was not affected by the simultaneous presence of bispecific blinatumomab or teclistamab for Axi-cel, Brexu-cel, Liso-cel or Ide-cel, respectively. Cilta-cel (containing an monomeric G4S-CAR linker) could not be detected by anti-CAR linker mAb. In conclusion, anti-CAR-linker mAbs are highly specific and useful for CAR T-cell monitoring but not universal applicable.

Hyperspectral imaging data holds great potential for various stages of the mining life cycle in active and abandoned mines. The technology, however, has yet to achieve large-scale industrial implementation and acceptance. While hyperspectral satellite im-agery yields high spectral resolution, high signal-to-noise ratio (SNR), and global availability with breakthrough satellite sys-tems like EnMAP, EMIT, and PRISMA, limited spatial resolution poses challenges for mining sectors, which require decimeter- to centimeter-scale spatial resolution for applications such as reconciliation, ore/waste estimates, geotechnical assessments, and en-vironmental monitoring. Hyperspectral imaging from drones (Uncrewed Aerial Systems; UASs) offers high spatial resolution data relevant to the pit/ mine scale, with the capability for frequent, user-defined re-visit times. Collecting data in the visible to near and shortwave infrared (VNIR-SWIR) wavelength regions offers to detect different minerals and surface alteration patterns, potentially revealing crucial information for exploration, extraction, re-mining, waste remediation, and rehabilitation. In this paper, we review of applicable instrumentation, software components, and relevant studies deploying hyperspectral imaging in or appropriate to the mining sector, especially for hyperspectral VNIR-SWIR UASs. If directly applicable, draw on previous insights derived from airborne, satellite, and ground-based imaging systems. We also discuss common practices for UAS survey planning and sampling considerations for interpretation.

Hyperspectral imaging data holds great potential for the different stages of the mining life cycle in active and post-mining environments. However, the technology has yet to reach the stage of large-scale industrial implementation and acceptance. While hyperspectral satellite imagery can achieve high spectral resolution, signal-to-noise ratio (SNR) and global availability with break-through satellite systems like EnMAP, EMIT and PRISMA, limited spatial resolution poses chal-lenges for sectors like mining, which require decimetre to centimetre scale resolution for applica-tions such as reconciliation, ore/waste estimates, geotechnical assessments and environmental monitoring. Hyperspectral imaging from drones (referred to herein as Uncrewed Aerial Systems; UASs) offers high spatial resolution data relevant to the camp/ mine scale, with the capability for frequent, user-defined re-visit times. This has been made possible by the miniaturization of hy-perspectral imaging systems. Collection of data in the visible to near and shortwave infrared (VNIR-SWIR) wavelength regions enables the detection of different minerals and surface altera-tion patterns potentially revealing crucial information for exploration, extraction, re-mining, waste remediation, and rehabilitation. In this paper, we provide a review of relevant studies de-ploying hyperspectral imaging in or applicable to the mining sector, especially for the use of hy-perspectral VNIR-SWIR Uncrewed Aerial Systems. Where required, we draw on previous in-sights derived from satellite or ground-based systems. We also discuss UAS survey planning, and sampling considerations for validation and interpretation.

Machine learning and computer vision have proven to be valuable tools for farmers to streamline their resource utilization to lead to more sustainable and efficient agricultural production. These techniques have been applied to strawberry cultivation in the past with limited success. To build on this past work, in this study two separate sets of strawberry images, along with their associated diseases, were collected and subjected to, resizing, and augmentation. Subsequently, a combined dataset consisting of 9 classes was utilized to fine-tune three distinct pre-trained models: Vision Transformer (ViT), MobileNetV2, and ResNet18. To address the imbalanced class distribution in the dataset, each class was assigned weights to ensure nearly equal impact during the training process. To enhance the outcomes, new images were generated by removing backgrounds, reducing noise, and flipping them. The performances of ViT, MobileNetV2, and ResNet18 were compared after being selected. Customization specific to the task was applied to all three algorithms, and their performances were assessed. Throughout this experiment, none of the layers were frozen, ensuring all layers remained active during training. Attention heads were incorporated into the first 5 and last 5 layers of MobileNetV2 and ResNet18, while the architecture of ViT was modified. The results indicated accuracy factors of 98.4%, 98.1%, and 97.9% for ViT, MobileNetV2, and ResNet18, respectively. Despite the data being imbalanced, the precision, which indicates the proportion of correctly identified positive instances among all predicted positive instances, approached nearly 99% with the ViT. MobileNetV2 and ResNet18 demonstrated similar results. Overall, the analysis revealed that the Vision Transformer model exhibited superior performance in strawberry ripeness and disease classification. The inclusion of attention heads in the early layers of ResNet18 and MobileNet18, along with the inherent attention mechanism in ViT, improved the accuracy of image identification. These findings offer the potential for farmers to enhance strawberry cultivation through passive camera monitoring alone, promoting the health and well-being of the population.

Background: Patients with atrial fibrillation (AF), lasting >48 h, considered for cardioversion, are recommended ≥3 weeks of oral anticoagulation before sinus rhythm restoration because of high risk of development of left atrial thrombosis (LAT) and stroke. However, the optimal duration of anticoagulation in the presence of overt LAT is unknown. Methods: An open-label study, aiming to investigate the prevalence of spontaneous echo con-trast (SEC) and LAT before and after 3 weeks of direct oral anticoagulant (DOAC) treatment. We included 51 consecutive patients (50.9% males), mean age 69.3±7.4 years with paroxys-mal/unknown duration of AF, considered for cardioversion, who agreed to have transesophage-al echocardiography at enrollment and 3 weeks later. Results: At baseline SEC was present in 26 (50.9%) and LAT in 10 (19.6%) of 51 patients. After 3 weeks on DOAC, SEC persisted in 12 (25.0%) and LAT in 7 (14.5%) of 48 patients, p<0.05 vs base-line. Factors, associated most strongly with persistence of SEC/LAT were left atrial appendage (LAA) emptying velocity <20 cm/s (OR=2.82), LAA lobes >2 (OR=1.84) and indexed left atrial volume ≥34 ml/m2 (OR=1.37). Conclusions: The recommended minimal period of 3 weeks of oral anticoagulation lead to SEC/LAT resolution in 47% of our patients. To our opinion, LA/LAA morphology and function should be taken into account when determining the duration of DOAC treatment before planned cardioversion.

Structural Health Monitoring (SHM) plays a vital role in ensuring the health status of a wide range of structures, such as bridges, buildings and large infrastructure in general. The advantages of this process can be further enhanced by incorporating more numerical and statistical approaches into traditional methods, such as Finite Element Analysis and Machine Learning. In this study a bridge structure is examined, and neural networks are trained with data derived from finite element analyses under static loads and dynamic excitations. Initially, a binary classification problem is addressed, where numerically trained classifiers are tasked with identifying whether the structure is in a healthy state or not. This category is further divided into two subcategories, depending on the extent of the damage present in the structure. Subsequently, a multi-class classification problem is defined, where three different damage classes of the same extent are considered, and the trained network is required to distinguish between them. Finally, conclusions are drawn from the results of the study regarding the model error parameter, the impact of the damage size, as well as the types of neural networks and training data used.

Wearable devices have a significant impact on society and recent advancements in modern sensor technologies are opening up new possibilities for healthcare applications. Continuous vital sign monitoring using IoT can be a crucial tool for emergency management, reducing risk in rescue operations and ensuring the safety of workers.The massive amounts of data, high network traffic, and computational demands of a typical IoT monitoring application can be challenging to manage with traditional infrastructure. Cloud computing provides a solution with its built-in resilience and elasticity capabilities.This article presents a cloud-based monitoring architecture for remote vital sign tracking of paramedics and medical workers through the use of a mobile wearable IoT device. It enables the management of ECG, breathing patterns, and other vital signs during work sessions, and sends real-time alarm events to a personnel management center. The platform was extensively used and tested in a large-scale monitoring application for tracking the activities of emergency room and ambulance workers, and the results of this testing are presented.

Increases in water temperature caused by climate change will challenge water and species management in the San Francisco Estuary. Our goals were to describe spatial and seasonal patterns in water temperature across the upper Estuary, and evaluate how temperature stress and suitability vary across the aquatic ecosystem. We synthesized 10 years of continuous water temperature data at 75 stations across six regions of the Estuary between 2010 and 2019. We identified stressful temperature thresholds for species of interest using published physiological limits and observed distribution, including ESA-listed native (e.g., osmerids, salmonids), non-ESA-listed native (e.g., cyprinids), non-native (e.g., centrarchids, bivalves), and nuisance species such as invasive aquatic vegetation, and harmful cyanobacteria. We then quantified thermal stress across varying spatial and temporal scales and metrics. Analyses indicated there were detectable regional temperature differences, and that Suisun Bay was the only region to provide regular thermal refuge during the warmer parts of the year, though portions of the Confluence and Suisun Marsh also provided potential thermal refuge during summer/fall and during cooler parts of the day. Meanwhile, the Central and South Delta experienced the warmest temperatures, exceeding thresholds for listed species throughout summer and early fall. We found that listed species such as juvenile salmonids and osmerids experience more thermal stress across a number of metrics. Fishes with higher heat tolerance (including non-natives and select natives), aquatic vegetation, and Microcystis (a harmful cyanobacteria) had the lowest average number of thermal stress days. This study demonstrates that the Estuary is already exhibiting stressful conditions for species of concern, and thermal stress will only increase with climate change. We identify at what times of year and where the Estuary may provide refuge from thermal stress conditions which has important implications for restoration prioritization and design and species management.

This study was carried out with a low-cost electronic nose prototype based on eight metal oxide sensors (MQ) in order to characterize samples of lemons treated with 0.5% and 0.1% of sodium benzoate. The MQ sensors designed are sensitive to one or more chemicals to detect the presence of a variety of chemicals in the air. The sensor MQ135 detects ammonia, hydrogen sulphide and benzene. Signal data were studied to obtain a pattern recognition of rotten in lemon fruits. Network analysis was used to obtain a calibration of measures among the stage of lemons. In this article, an electronic nose prototype based on 8 MQ metal oxide sensors has been used in order to analyze and characterize different lemon varieties to which different chemical treatments have been applied in pre-harvest. PCA-based data analyzes were used to observe clusters in the data. Through the combined use of the data obtained by the nose and these Sequential Neural Networks (SNNs) a classification tool for lemon varieties and applied treatments has been obtained. It is shown the ability of this device to be used as a reliable discrimination method, in addition to providing low cost and optimization of time and expert resources.

Animal research has always been crucial for various medical and scientific breakthroughs, providing information on disease mechanisms, genetic predisposition to diseases, and pharmacological treatment. However, the use of animals in medical research is a source of great controversy and ongoing debate in modern science. To ensure a high level of bioethics, new guidelines have been adopted to replace animal testing wherever possible, reduce the number of animals per experiment, and refine procedures to minimize stress and pain. Supporting these guidelines, this article proposes a novel approach for unobtrusive, continuous, and automated monitoring of the respiratory rate of laboratory rats. It uses the cyclical expansion and contraction of the rats’ thorax/abdominal region to determine this physiological parameter. In contrast to previous work, the focus is on unconstrained animals, which requires the algorithms to be especially robust to motion artifacts. To test the feasibility of the proposed approach, video material of multiple rats was recorded and evaluated. High agreement was obtained between RGB-imaging and the reference method (respiratory rate derived from electrocardiography), which was reflected in a relative error of 5.46%. The current work shows that camera-based technologies are promising and relevant alternatives for monitoring the respiratory rate of unconstrained rats, contributing to the development of new alternatives for continuous and objective assessment of animal welfare and hereby guiding the way to modern and bioethical research.

This article provides a detailed analysis of non-invasive techniques for prediction and diagnosis of faults in internal combustion engines, focusing on the application of the Proknow-C and Methodi Ordinatio systematic review methods. Initially, the relevance of these techniques in promoting energy sustainability and mitigating greenhouse gas emissions is discussed, aligning with the Sustainable Development Goals (SDGs) of Agenda 2030 and the Paris Agreement. The systematic review conducted in the subsequent sections offers a comprehensive mapping of the state-of-the-art, highlighting the effectiveness of combining these methods in categorizing and systematizing relevant scientific literature. The results reveal significant advancements in the use of artificial intelligence (AI) and digital signal processors (DSP) to enhance fault diagnosis, as well as underscore the crucial role of non-invasive techniques in minimizing interference in monitored systems. Finally, concluding remarks point towards future research directions, emphasizing the need to develop digital twins for internal combustion engines and identify gaps for further improvements in fault diagnosis and prediction techniques.

Low-cost personal exposure monitors (PEMs) to measure personal exposure to air pollution are potentially promising tools for health research. However, their adoption requires robust validation. This study evaluated the performance of twenty-one Plume Lab Flow2 (PLF) by comparing its air pollutant measurements, particulate matter with a diameter of 2.5 μm or less (PM2.5), 10 μm or less (PM10), and nitrogen dioxide (NO2), against several high-quality air pollution monitors under field conditions (at indoor, outdoor, and roadside locations). Correlation and regression analysis were used to evaluate measurements obtained by different PLFs against reference instrumentation. For all measured pollutants, the overall correlation coefficient between the PLFs and the reference instruments was often weak (r<0.4). Moderate correlation was observed for one PLF unit at indoor location and two units at roadside location, when measuring PM2.5, but not for PM10 and NO2 concentration. During periods of particularly higher pollution, 11 PLF tools showed stronger regression results (R2 values > 0.5) with one-hour and 9 PLF units with one-minute time interval. Results show that the PLF cannot be used robustly to determine high and low exposure to poor air. Therefore, the use of PLFs in research studies should be approached with caution if data quality is important to the research outputs.

The deformation of underground gateroads tends to be asymmetric and complex. Traditional instrumentation fails to accurately and conveniently monitor the full cross-sectional deformation of underground gateroads. Here, a full cross-sectional laser scanner was developed together with a visualization software package. The developed system used polar coordinate measuring method and the full cross-sectional measurement was realized by 360° rotation of laser sensor driven by an electrical motor. Later on, the potential impact of gateroad wall flatness, roughness and geometrical profile as well as coal dust environment on the performance of the developed laser scanner were evaluated. The studies show that a high-level flatness is favorable in application of the developed full cross-sectional deformation monitoring system. For a smooth surface of gateroad, the sensor cannot receive reflected light when the incidence angle of laser beam is large, causing data loss. Conversely, the roughness surface shows its priority as the diffuse reflection light can be received by the sensor. With regards to the coal dust in measurement environment, the fine particles of floating coal dust in the air can lead to the loss of measurement data to some certain due to scattering of laser beam.

We developed a sensor optimized for joint motion monitoring by exploring the effects of stitch pattern, yarn thickness, and NP number on the performance of knitted strain sensors. We conducted stretching experiments with basic weft-knit patterns to select the optimal stitch pattern and analyze its sensitivity and reproducibility. The plain stitch with a conductive yarn located on the reverse side exhibited the highest gauge factor value (143.68) and achieved excellent performance, with a stable change in resistance even after repeated sensing. For in-depth analysis, we developed six sensors using the aforementioned pattern with different combinations of yarn thickness (1-ply, 2-ply) and NP number (12, 13, 14). Based on bending experiments, the GF across all sensors was 60.2–1092, indicating noticeable differences in sensitivity. However, no significant differences were observed in reproducibility, reliability, and responsiveness, confirming that all the sensors are capable of joint motion monitoring. Therefore, the plain-patterned plating stitch structure with conductive yarn on the reverse side is optimal for joint motion monitoring, and the yarn thickness and NP numbers can be adjusted to suit different purposes. This study provides basic data for developing knitted strain sensors and offers insights into how knitting methods impact sensor performance.

The emission of sulphur dioxide (SO2) from mining activities presents a substantial risk to public health, especially in populations located near mine industrial regions. This study investigated the potential correlation between exposure to sulphur dioxide (SO2) and its effects on respiratory health in Kankoyo Township, Zambia. A variety of methodologies were employed in this study, encompassing community participation, expert interviews, spatial analysis, and a retrospective examination of health and SO2 data for Kankoyo spanning 15 years. The results of our research indicated a worrisome correlation between the community and the presence of SO2, which has had a significant impact on their lives. The expert interviews also emphasized the effects of SO2, with respiratory cases accounting for approximately 75% of the reported cases. Additionally, the clinic officer observed that asthma cases have decreased following the implementation of a monitoring station in the community. Furthermore, overall emissions of SO2 have decreased since the upgrade of the smelter operation. A probable association was identified in the retrospective analysis between exposure to SO2 and the occurrence of asthma, respiratory non-pneumonia, and pneumonia infections. The findings of the retrospective research revealed a substantial association between SO2 concentrations and the susceptibility of individuals aged 5 years and older to asthma, respiratory non-pneumonia, and pneumonia infections. The results of the spatial study indicated that Kankoyo exhibited a significant level of SO2 pollution, above the established limitations set by the Zambian Environmental Management Agency (ZEMA) by an alarming margin of 1713%. In response to the challenges identified, this study proposed several measures. These measures encompassed the implementation of a requirement for regulators such as ZEMA and local communities to have access to real-time pollution data from mines, to enhance transparency. Additionally, the deployment of affordable air quality sensors, the resolution of medication shortages, the establishment of specialized respiratory health clinics, the initiation of IT-driven public awareness campaigns, and the expansion of research to investigate additional pollutants and confounding factors were also recommended.

This paper presents an on-device semi-supervised human activity detection system that can learn and predict human activity patterns in real time. The proposed semi-supervised learning (SSL) framework uses sparsely labelled user activity events acquired from Inertial Measurement Unit (IMU) sensors installed as wearable device. The objective is to learn classification of multiple classes of human activities in real-time. The proposed cluster-based learning model in this approach is trained with data from the same target user, thus preserving data privacy while providing personalized activity detection services. Two different cluster labelling strategies, namely, population-based, and distance-based, are employed to achieve the desired classification performance. A comparative study of these strategies has been presented in terms of classifiability and classification accuracies. The proposed system is shown to be computationally efficient, which is relevant in the context of limited computing resources on typical wearable devices. The trade-off between classification accuracy and computation complexity is analyzed for different algorithmic hyper-parameters and other system parameters. Extensive experimentation and simulation study have been conducted on a multi-user human activity data from the public do-main in order to validate the proposed learning paradigm.

The widespread diffusion of electric vehicles poses new challenges in the field of fault diagnostics. Past studies have been focused mainly on machines designed for industrial applications, where the operating conditions and requirements are significantly different. This work presents a review of the most recent studies about fault diagnosis techniques in electrical machines feasible for traction applications, with a focus on the most adopted approaches of the last years and on the latest trends. Considerations about their applicability for electric vehicle purposes, along with some areas that require further research, are also provided.

Digital photogrammetry has attracted widespread attention in the field of geotechnical and geological survey due to its low-cost, ease of use and contactless mode. In this work, with the purpose of studying the progressive block surficial detachments of a landslide we developed a monitoring system based on fixed multi-view time-lapse cameras. Thanks to a new-developed photogrammetric algorithm based on the comparison of photo sequences through a structural similarity metric and the computation of the disparity map of two convergent views we can quickly detect the occurrence of collapse events, determine their location and calculate the collapse volume. With the field data obtained at the Perarolo landslide site (Belluno Province, Italy), we have preliminary tested the effectiveness of the algorithm and its accuracy in the volume calculation. The method of quickly and automatically obtaining collapse information proposed in this paper can extend the potentials of landslide monitoring system based on videos or photo sequence and it will be of great significance for further research on the link between the frequency of collapse events and the driving factors.

With an ever broadening use of composite materials manufacturers are in high demand of efficient curing cycles to reduce costs and speed up production cycles. One method to to archive this goal is active cure monitoring to determine the exact time of curing needed. This article provides a novel method to measure the cure inside of closed tools by using ultrasonic spectroscopy. For this a simple experiment is used to show the change of the ultrasonic spectrum during the cure of an epoxy. The results clearly show a direct correlation of amplitude and state of cure where the amplitude reaches a global minimum at the glass point.

This paper describes the proposal and development of a proof of concept (PoC) for a data logger system designed for operation and fault detection in bench testing of combustion engines. The main objective was to develop a data logger system that collects data on vibration, sound, temperature, and CO2 levels to identify ignition and combustion faults, thereby contributing to reducing greenhouse gas emissions (GHG). The paper presents (i) the proposal and development and (ii) the open-source code: proof of concept for a data logger system focused on detecting faults and monitoring the operational condition of benchtop combustion engines. The results indicate the feasibility of the PoC for data acquisition and dataset creation for Research and Development purposes.

Rotorcrafts operate HUMS for fault diagnosis, but the capabilities of HUMS analysts are important due to the complex mechanical configuration of rotorcraft and the difficulty of analysis. Accordingly, an advanced algorithm is needed to identify faults, and flight data can be used to develop the algorithm. However, flight data contains abnormal or missing data due to problems such as sensor defects, which can be a major problem in algorithm development. Therefore, in this paper, we study a gap filling method using MLP to obtain normal data when there are problems such as abnormal or missing data in rotorcraft flight data. Existing methods typically fill the gap through interpolation or curve fitting using the before and after values of missing data. However, in this study, normal values were estimated using the values of other parameters at the moment of missing or abnormal data occurred. As a result of evaluating the performance of the trained MLP using normal data, it was confirmed that the output of the model well estimates the changing trend of the target. And when abnormal data was applied to the trained model, it was confirmed that point outliers were eliminated and appropriate values were found in the case of missing data.

This article discusses the results of a series of experiments on pulse ultrasonic cure monitoring of carbon fiber reinforced plastics applied to the pultrusion process. The aim of this study is to validate the hypothesis that pulse ultrasonic cure monitoring can be applied a) for profiles having small cross sections such as 7x0.5 mm and b) within the environment of the pultrusion process. Ultrasonic transducers are adhesively bonded to the pultrusion tool as actuators and sensors. The time-of-flight and the amplitude of an ultrasonic wave are analyzed to deduce the current curing state of the epoxy matrix. The experimental results show that ultrasonic cure monitoring is indeed applicable even to very thin cross sections. However, significant challenges can be reported when the techniques are used during the pultrusion process.

Considering the evolution of search engine optimization (SEO) methods, it is crucial to generate and update relevant keywords continuously based on trends in a dynamic method to maintain the relevance and visibility of a web page, which enhances user engagement. To automate the process of continuous SEO, this paper proposes a method called AutoTrendyKeywords to leverage large language models (LLMs) to automate the constant generation of SEO keywords and the selection of trending keywords based on changing data. Unlike the manual selection method, the new system automatically uses real-time trend data from sources such as Google Trends. This unsupervised approach ensures up-to-date relevance of the page and can ensure satisfactory traffic for pages in unpopular languages when the web is dominated by content in popular languages. Additionally, the system offers transparency to understand the reason behind each keyword selected. The method streamlines the keyword update process for digital content creators and marketers by eliminating the need for manual intervention, thereby constantly ensuring visibility across search results. The system has wide-ranging societal benefits, such as facilitating access to desired information and promoting diverse languages. The system successfully generated keywords using an LLM, selected the most trending keywords, generated a title and description of the page for SEO, and integrated the keywords and the description into HTML code. The system generated URL paths that are short and contain the trending keywords.

Human Activity Recognition (HAR) technology enables continuous behavior monitoring, particularly valuable in healthcare. This study investigates the viability of using an ear-worn motion sensor for classifying daily activities, including lying, sitting/standing, walking, ascending stairs, descending stairs, and running. Fifty healthy participants (between 20 and 47 years old) engaged in these activities while under monitoring. Various machine learning algorithms, ranging from interpretable shallow models to state-of-the-art deep learning approaches designed for HAR, were employed for classification. Results demonstrate the ear sensor's efficacy, with deep learning models achieving 98% accuracy rate of classification. The obtained classification models are agnostic regarding which ear the sensor is worn and robust against moderate variations in sensor orientation (e.g., due to differences in auricle anatomy), meaning no initial calibration of the sensor orientation is required. The study underscores the ear's efficacy as a suitable site for monitoring human daily activity and suggests its potential for combining HAR with in-ear vital signs monitoring. This approach offers a practical method for comprehensive health monitoring by integrating sensors in a single anatomical location. This integration facilitates individualized health assessments, with potential applications in tele-monitoring, personalized health insights, and optimizing athletic training regimes.

Modern scientific research particularly radio astronomi- cal spectroscopic observations cannot be imagined without appropriate software suite. That is necessary because of two reasons 1) data are in digital form and 2) data processing is a complex multi-step process. In this paper created in VIRAC data processing suite for a single radio telescope, space maser observations are presented. Software Defined Radio (SDR) backend data processing is described. Implementation of the frequency switching algorithm, acquisition of observation data and their format for storing are discussed. Multiple ways to display the observation results are highlighted.

Condition monitoring of industrial robots has the potential to decrease downtimes in highly automated production systems. We suggest a new health indicator based on vibration data measurements and compare its performance with state-of-the-art health indicators regarding different criteria. This evaluation is based on different data sets from robot test rigs. We find that the proposed health indicator can detect different faults, has low temperature sensitivity and works in instationary velocity regimes. A discussion of the validity of the results rounds up our contribution.

Infrared sensors are applied more and more widely in industrial production applications. Based on the theory of thermal radiation, this paper discusses the system design principle, temperature calibration method and thermal image analysis method in detail. The system has passed the measurement unit certification, showing that the field of view is 180°, the number of scanning points is 2048, the linear velocity is 10-100Hz, the spatial resolution is 2.5mrad, and the precision is ±1℃. On-line monitoring test has been done in the steelmaking plant of Bao Steel. The results show that the system has strong anti-interference ability, stability and reliability, and meets the application requirements of online monitoring.

Therapeutic Drug Monitoring (TDM) is potentially a useful tool that can be employed to increase the efficacy and decrease the toxicity of antifungal drugs. The aim of this narrative review is to provide an overview of the current use of TDM in clinical practice, and to present the evidence available regarding its use in proactive clinical settings for preventing and managing treatment failure. This review also presents the existing evidence regarding the association of various clinical outcomes with specific thresholds of drug concentrations in everyday practice. Articles concerning the use of TDM of triazoles in the treatment of fungal infections were retrieved through an electronic search using PubMed. In clinical practice, TDM has an increasingly important role in the management of antifungal drugs as a consequence of the improvement in the knowledge of the pharmacokinetics and pharmacodynamics of these drugs. The currently available evidence shows a direct exposure-response relationship for triazoles, though the PK/PD profile is unpredictable. Current guidelines and treatment consensus statements recommend the proactive TDM of voriconazole, posaconazole, and itraconazole to optimize dosage regimens and improve outcomes for adult and pediatric patients.

Distributed tracing is a cutting-edge technology for monitoring, managing, and troubleshooting native cloud applications. It offers a more comprehensive and continuous observability, surpassing traditional logging methods, and is indispensable for navigating modern complex software architectures. However, the sheer volume of generated traces is staggering in distributed applications, and direct storage and utilization of every trace are impractical due to associated operational costs. This entails a sampling strategy to select which traces warrant storage and analysis. Historically, sampling methods have included a rate-based approach, often relying heavily on a manual configuration. There is a need for a more intelligent approach, and we propose a hierarchical sampling methodology to address multiple requirements concurrently. Initial rate-based sampling mitigates the overwhelming volume of traces, as no further analysis can be performed on this level. In the next stage, more nuanced analysis is facilitated based on the previous foundation, incorporating information regarding trace properties and ensuring the preservation of vital process details even under extreme conditions. This comprehensive approach not only aids in the visualization and conceptualization of applications but also enables more targeted analysis in later stages. As we delve deeper into the sampling hierarchy, the technique becomes tailored to specific purposes, such as simplifying application troubleshooting. In this context, the sampling strategy prioritizes the retention of erroneous traces from dominant processes, thus facilitating the identification and resolution of underlying issues. The focus of this paper is to reveal the impact of the sampling on troubleshooting efficiency. Leveraging intelligent and explainable artificial intelligence solutions enables the detection of malfunctioning microservices and provides transparent insights into root causes. We advocate for using rule-induction systems, which offer explainability and efficacy in decision-making processes. By integrating advanced sampling techniques with machine learning-driven intelligence, we empower organizations to navigate the complexities of large-scale distributed cloud environments effectively.

The aim of this work is to propose two different and complementary sensors for the structural health monitoring of concrete beams. In particular, a diffused sensing element and a split ring resonator network are presented. The first sensor is able to detect the variation of the dielectric properties of the concrete along the whole beam length, for a diffuse monitoring both during the important concrete curing phase and also for the entire life cycle of the concrete beams. The resonators instead work punctually, in their surroundings, allowing an accurate evaluation of the permittivity both during the drying phase and after. This allows the continuous monitoring of any presence of water both inside the concrete beam and in points that can be critical, in the case of beams in dams, bridges or in any case subject to a strong presence of water which could lead to deterioration, or worse, cause serious accidents. Moreover, the punctual sensors are able to detect the presence of cracks in the structure and to localize them.

Little is known about how recreational triathletes prepare for an Olympic distance event. The aim of this study was to identify the training characteristics of recreational-level triathletes within the competition period and assess how their preparation for a triathlon influences their health and their levels of fatigue. During the 6 weeks prior to an Olympic distance triathlon, and the 2 weeks after, 9 recreational athletes (5 males, 4 females) completed a daily training log. Participants answered the Daily Analysis of Life Demands Questionnaire (DALDA), the Training Distress Scale (TDS), and the Alberta Swim Fatigue and Health Questionnaire weekly. The Recovery-Stress Questionnaire (REST-Q) was completed at the beginning of the study, on the day before the competition, and at the end of week 8. Training loads were calculated using session-based rating of perceived exertion (sRPE). The data from every week of training was compared to week 1 to determine how athletes’ training and health changed throughout the study. No changes in training loads, duration, or training intensity distribution were seen in the weeks leading up to the competition. Training duration was significantly reduced in week 6 (p=0.041, d = 1.58, 95% CI = 6.9, 421.9), while the number of sessions was reduced in week 6 (Z=2.32, p=0.02, ES = 0.88) and week 7 (Z = 2.31, p=0.02, ES = 0.87). Training was characterized by large weekly variations in training loads and a high training intensity. No significant changes were seen in the DALDA, TDS, or REST-Q questionnaire scores throughout the 8 weeks. Despite large spikes in training load and a high overall training intensity, these recreational-level triathletes were able to maintain their health in the 6 weeks of training prior an Olympic distance triathlon.

Remote sensing has been used as an important tool for disaster monitoring and disaster scope extraction, especially for the analysis of temporal and spatial disasters patterns of large-scale long time series. In order to find out a rapid and effective method to monitor disaster in a wide range, based on the Google Earth Engine cloud platform, this study used MODIS vegetation index products of 250 meter spatial resolution synthesized in 16 days during the year 2005-2019 and three kinds of disaster monitoring and scope extraction models are proposed: normalized vegetation index median time standardization (RNDVI_TM(i)) model, the normalized vegetation index median phenology Standardization(RNDVI_AM(i)(j)) model, normalized vegetation index median spatiotemporal Standardization (RNDVI_ZM(i)(j)) model. The optimal threshold of disaster extraction for each model in different time phases was determined by Otsu method, and the extraction results were verified by Medium resolution image and ground measured data of the same or quasi-same period. Finally, the disaster scope of cultivated land in Heilongjiang province from 2010 to 2019 was extracted and the temporal and spatial pattern of disasters was analyzed based on the meteorological data. It shows that the three above-mentioned models have high disaster monitoring and range extraction capabilities with the verification accuracy of RNDVI_TM(i) 97.46%, RNDVI_AM(i)(j) 96.90%, and RNDVI_ZM(i)(j) 96.67% respectively. The spatial and temporal distribution of disasters is consistent with the disaster of the insured plots and meteorological data in the whole province. Meanwhile, it turns out that different monitoring and extraction methods are used in different disasters, among which wind hazard and insect disasters often need to be delayed for 16 days to observe. Each model also has various sensitivity and applicability to different disasters. Compared with other methods, this method is fast, and convenient, which allows it to be used for large-scale agricultural disaster monitoring and is easy to be applied into other research areas. The research provides a new idea for large-scale agricultural disaster monitoring.

(1) Objective: This study aims to lay a foundation for non-contact intensive care monitoring of premature babies. (2) Methods: Arterial oxygen saturation and heart rate were measured using a monochrome camera and a time division multiplex controlled lightning with three different wavelengths (660 nm, 810 nm and 940 nm) on a piglet model. (3) Results: Using the camera system and our newly designed algorithm for further analysis, the detection of a heartbeat and the calculation of oxygen saturation was evaluated. In motionless individuals, heartbeat and respiration were separated clearly during light breathing and only minor intervention. In this case, the mean difference between non-contact and contact saturation measurements was 0.7% (RMSE = 3.8%, MAE = 2.93%). (4) Conclusions: The new sensor has proven effective under ideal animal experiment conditions. The results allow a systematic improvement for the further development of contactless vital sign monitoring systems. The results presented here are a major step towards the development of an incubator with non-contact sensor systems for use in the neonatal intensive care unit.

Ischemia, the inadequate blood flow, can arise from pre-existing or traumatic events, remain an undetectable issue, and impact the body's ability to provide oxygen to necessary limbs, organs, muscles, or tissue. New technology involving wearable ultrasonic devices allows medical professionals to gain real-time insight into the cardiovascular system of their patients. A non-invasive, postage-stamp-sized ultrasonic sensor can be attached to a patient, allowing for continuous monitoring of the patient’s blood pressure outside of the hospital. After reviewing 16 papers on ultrasonic sensors, this paper intends to review the current use of wearable ultrasonic sensors and the advantages and limitations of the technology used to obtain accurate blood pressure readings. This review will bring attention to the evolving and expanding world of wearable ultrasonic sensors for medical applications.

This study proposes a prototype (Business Intelligence) for monitoring the continuing education of indigenous health professionals at the Secretariat of Indigenous Health (SESAI) of Brazil’s Ministry of Health (MS). The prototype builds on SESAI/MS staff knowledge and takes into account the char-acteristics and demands of the 34 Special Indigenous Health Districts (DSEIs). The prototype provides information for managing SESAI/MS continuing education in order to meet strategic goals. By im-proving the effectiveness and efficiency of the continuing education of professionals who serve Bra-zil’s indigenous population, we will be acting directly on access issues and improving the quality of life of the indigenous population.

Non-invasive continuous health monitoring has become feasible with the advancement of biosensors. While monitoring certain biomarkers such as heart rate or skin temperature are now at certain maturity, monitoring molecular biomarkers is still challenging. Progress has been shown in sampling, measurement and interpretation of data towards non-invasive molecular sensors that can be integrated in daily wearable items. Towards this goal, this paper explores the potential of embroidered interdigitated transducer (IDT)-based sensors for non-invasive, continuous monitoring of human biomarkers, particularly glucose levels, in human sweat. The study employs innovative embroidery techniques to create flexible fabric-based sensors with gold-coated IDTs. In controlled experiments, we have shown the variation of glucose concentration in water can be wirelessly detected by tracking the resonant frequency of the embroidered sensors. The current sensors operate at 1.8GHz–2GHz and respond to the change of glucose concentration with a sensitivity of 0.17 MHz/(mg/dl). The embroidered IDT-based sensors with wireless sensing will be a new measurement modality for molecular wearable sensors. The establishment of a wireless sensing mechanism for embroidered IDT-based sensors will be followed by investigation of sweat for molecular detection. This will require adding functionalities for sampling and interpretation of acquired data. We envisage the embroidered IDT-based sensors offer a unique approach for seamless integration into clothing, paving the way for personalised, continuous health data capture.

Wind energy is a kind of renewable energy with great potential for development. This study mainly investigated the application of shock waves generated by high-pressure gases (wind energy) for generating energy. In this study, we designed a new supersonic shock wave generator that can be reused without disassembling and assembling bolts and developed a supersonic shock wave monitoring system. This system monitored the velocity of the generated shock waves, which was Mach 3-5, and the output pressure was more than 100 times higher than the input pressure of the shock wave generator tank.Then, we developed a power generation system driven by supersonic shock waves based on the characteristics of the new shock wave generator, which can generate high-pressure and high-speed blast waves and can be reused. The shock wave generator can repeatedly generate high-pressure waves to drive the Tesla turbine and then the magnetic energy generator for power generation. We established a complete control process for power generation driven by shock waves by controlling the valve stem. The system can detect the tank pressure, output pressure, gas flow, rotation speed, voltage, and current during the control process for the performance analysis of power generation.

This article explores the use of vegetation indices (VIs) in remote sensing for estimating standing wood volume and volume increments in forest ecosystems. The study investigates the correlations between various VIs and wood volume across different forest stand age classes, focusing on the effectiveness of commonly used indices such as Squared Ratio Simple Red Edge (SQSR) and Red-Edge Ratio Vegetation Index (RERVI), as well as other typical indicators including Enhanced Vegetation Index (EVI), Red-Edge EVI (RE-EVI), and Green Normalized Difference Vegetation Index (GNDVI). Additionally, the analysis considers a pair of indicators based on blue and near-infrared channels, resembling the Blue-normalized Difference Vegetation Index (BNDVI). The research reveals that quadratic and power-law models of SQSR and RERVI demonstrate higher correlations (>0.40) with wood volume, especially in younger forest stands (>0.80). Furthermore, the study highlights the potential of NDII and NDWI indices for estimating volume increments in certain classes of forest stands (0.70). However, correlations vary across different forest stand classes, suggesting the need for further investigation into the reliability of VIs for monitoring wood volume and volume increments in forest ecosystems. Overall, this research contributes to the understanding of the applicability of VIs in remote sensing for forest management and ecosystem monitoring.

Shared public buildings have become centers of innovation, integrating advanced technologies to meet evolving societal needs. With a heightened emphasis on occupants’ health and well-being, these buildings serve as hubs for technological convergence, facilitating seamless connectivity and intelligent data analysis and management. Within this context, environmental monitoring emerges as a foundational element, pivotal to all aspects of building management. This article provides findings from the nationally funded RE-START project, which focuses on shared public buildings, with special regard to educational and medical facilities. The project explores enhanced indoor air quality monitoring, focusing in particular on CO2 concentration that is directly correlated with occupancy, as a fundamental element for developing health and safety protocols, energy efficiency strategies, integration of smart building technologies, and data-driven energy management. The intersection of environmental monitoring, energy efficiency, security, and IoT technologies in in indoor spaces are relevant. The outcomes of the study reveal the delicate nature of all the involved components, that need to be carefully developed in an integrated manner.

Currently, old-style personal medicare techniques rely mostly on traditional methods, such as cumbersome tools and complicated processes, which can be time-consuming and inconvenient in some circumstances. Furthermore, such old methods need the use of heavy equipment, blood draws, and traditional bench-top testing procedures. Invasive ways of acquiring test samples can potentially cause patients discomfort and anguish. Wearable sensors, on the other hand, may be attached to numerous body areas to capture diverse biochemical and physiological characteristics as a developing analytical tool. Physical, chemical, and biological data transferred via the skin is used to monitor health in various circumstances. Wearable sensors can assess the aberrant conditions of the physical or chemical components of the human body in real-time, exposing the body state in time, thanks to unintrusive sampling and high accuracy. Most commercially available wearable gadgets are mechanically hard components attached to bands and worn on the wrist, with form factors ultimately constrained by the size and weight of the batteries required for the power supply. Wearable gadgets with “skin-like” qualities are a new type of automation that is only starting to make its way out of research labs and into pre-commercial prototypes. In this paper, we studied the recent advancement in battery-powered wearable sensors established on optical phenomena and skin-like battery-free sensors which brings a breakthrough in wearable sensing automation.

In this paper, we introduce a non-invasive approach for monitoring bridge infrastructure with ground-based interferometric radar. This approach is called the mirror mode, since it utilises the flat surface of the bridge underside as a mirror to reflect the signal to a corner reflector on the ground placed opposite of the radar sensor. For proving the feasibility of this approach, a measurement campaign has been carried out at an exemplary bridge in Karlsruhe (Germany) including a radar sensor in mirror mode, a second radar sensor in the default mode and a laser profile scanner. We investigate the potential of this approach to monitor the bridge displacement in vertical direction and compare the results with the two other sensors. The derived results reveal the potential for monitoring bridge infrastructure. Finally, we propose further research aspects of this approach to analyse its capabilities and limitation in the context of non-invasive infrastructure monitoring.

This study examines a case involving a 7-year-old child who developed dengue symptoms following Qdenga vaccination. Despite initial negative diagnostic results, molecular analysis confirmed an infection with DENV4. Next-generation sequencing detected viral RNA from both DENV2 and DENV4 serotypes, which were identified as vaccine-derived strains using specific primers. Phylogenetic analysis further confirmed that these sequences belonged to the Qdenga vaccine rather than circulating wild-type viruses. This case underscores the critical need for precise diagnostic interpretation in vaccinated individuals to avoid misdiagnosis and to strengthen public health surveillance. A comprehensive understanding of vaccine-induced viremia is essential for refining dengue surveillance, improving diagnostic accuracy, and informing public health strategies in endemic regions.

Background: Ice formation on power transmission lines presents significant risks, including structural damage and power outages. Traditional methods for detecting ice on these lines have limitations, particularly in challenging environmental conditions. This study aims to enhance ice detection accuracy by introducing a novel image segmentation and edge detection methodology using improved multi-scale Retinex and advanced morphological operations. Method: The proposed method integrates multi-stage image processing techniques, including image enhancement, grayscale conversion, thresholding, segmentation, object isolation, and edge detection. High-resolution binocular cameras were used to capture images of ice formations on transmission lines. The effectiveness of the method was assessed through a series of metrics, including accuracy, sensitivity, specificity, and precision, and compared with existing methodologies. Results: The proposed method demonstrated superior performance in both ice detection and thickness measurement. The method effectively identified and isolated ice formations under various conditions with an average accuracy of 98.35%, sensitivity of 91.63%, specificity of 99.42%, and precision of 96.03%. Additionally, the analysis of ice thickness measurements further highlighted the method’s accuracy, with a notably low root mean squared error (RMSE) of 1.20 mm and mean absolute error (MAE) of 1.10 mm, along with a strong R-squared value of 0.95. These statistical metrics show that the proposed method not only outperforms previous methods in consistency and alignment with manual measurements but also stands out as the most reliable option for tasks requiring precise measurements, offering significant advancements in accuracy and reliability over existing methodologies. Conclusions: The enhanced image segmentation and edge detection approach provides a more accurate and reliable method for monitoring ice formations on power transmission lines.

A single paragraph of about 200 words maximum. For research articles, abstracts should give a pertinent overview of the work. We strongly encourage authors to use the following style of structured abstracts, but without headings: (1) Background: Place the question addressed in a broad context and highlight the purpose of the study; (2) Methods: briefly describe the main methods or treatments applied; (3) Results: summarize the article’s main findings; (4) Conclusions: indicate the main conclusions or interpretations. The abstract should be an objective representation of the article and it must not contain results that are not presented and substantiated in the main text and should not exaggerate the main conclusions.

The process industry is confronted with rising demands for flexibility and efficiency. One way to achieve this are modular process plants that consist of pre-manufactured modules with their own decentralized intelligence. Plants are then composed of these modules as unchangeable building blocks and can be easily re-configured for different products. Condition monitoring of such plants is necessary, but available solutions are not applicable. The authors suggest an approach in which model-based symptoms are derived from few measurements and observers that are based on manufacturer knowledge. The comparisons of redundant observers lead to residuals that are classified to obtain symptoms. These symptoms can be communicated to the plant control and are inputs to an easily adaptable diagnosis. The implementation and validation at a modular mixing plant showcases the feasibility and the potential of this approach.

The application of distributed fiber optic strain and temperature measurement can be utilized to address a multitude of measurement tasks across a diverse range of fields, particularly in the context of structural health monitoring in the domains of building construction, civil engineering, and special foundation engineering. However, a comprehensive understanding of the influences on the measurement method and the sensors is essential to prevent misinterpretations or measurement deviations. In this context, this study investigated the effects of moisture exposure, including various salt solutions and a high pH value, on a distributed strain measurement using Rayleigh backscattering. Three fiber optic sensors with different coating materials and one uncoated fiber were exposed to five different solutions for 24 hours. The study revealed significant discrepancies in deformation between the three coating types depending on the surrounding solution. Furthermore, in contrast to the prevailing literature, which predominantly describes swelling effects, a negative deformation was observed in a magnesium chloride solution. The findings of this study indicate that corresponding effects can impact the precision of measurement, potentially leading to misinterpretations. Conversely, these effects could be used to conduct large-scale monitoring of chemical components using distributed fiber optic sensing.

Induction heating is a fast, reproducible, and efficient heating method used in various manufacturing processes. However, there is no established additive manufacturing (AM) process based on induction heating using wire as feedstock. This study investigates a novel approach to AM based on inductive heating, where a steel wire is melted and droplets are detached periodically using a two-winding induction coil. The process parameters and energy input into the droplets are characterized. The induction generator exhibits sluggish response to the excitation voltage, resulting in a lag in the coil current. The process is captured using a high-speed camera, revealing regular droplet formation and uniform size and shape when operated within an appropriate process window. Larger drops and increased spatter formation occur outside this window. The proposed method allows for the production of droplets with almost spherical shapes. Further analysis and characterization of droplet formation and energy input provide insights into process optimization and overall efficiency.

This chapter aims to construct a relatively complete, universal, and highly reliable road surface state monitoring and perception system through the research of the A1 contact road reconstruction project of an international airport (hereinafter referred to as the “airport”). The system design is based on on-the-spot investigation, theoretical analysis, and engineering practice, using vibrating string type and resistive strain sensors as sensing means, real-time high-frequency signal acquisition technology as the guide, 4G router for wireless communication technology as the media, and storage technology for monitoring system based on server storage terminals. In combination with engineering background, aircraft motion state, main landing gear configuration, sensor selection and evaluation, and other major factors, the actual monitoring information needs of the plane are fully taken into account, as well as the difference in sensor information types, and the system design is carried out by stratification and classification.

Health management in industrial systems is more critical in maintenance management and it plays an important role in productivity, fault diagnosis, safety, efficiency, and economy in manufacturing industries. Early detection of faults in machinery may increase the effectiveness of maintenance actions and will avoid unwanted consequences in process operations and maintenance. Existing fault diagnosis methods have limitations such as insufficient accuracy, slow detection rate, and handling large and complex data sets. In this digital age, Industry 4.0 techniques have been applied across all fields, including the condition monitoring of machines. This research addresses the gaps in traditional fault diagnosis by using deep learning, a modern AI technique effective for diagnosing faults in various machines. Deep learning algorithms Multilayer Perceptron (MLP), Coevolutionary Neural Network (CNN), and Recurrent Neural Network (RNN) with Long Short-Term Memory (LSTM) are tested for fault diagnosis using vibration datasets collected from Spectra Quest Machinery Fault Simulator (SQMFS). In this research work, NI-DAQ (National Instruments- Data Acquisition) system, accelerometer, and LabVIEW software are used to collect vibration signals. Preprocessing of the signals has been done using a sampling strategy, shuffling, standardization, and reshaping data augmentation. The result shows that MLP accuracy in the prediction of fault is 0.9, CNN reached 0.95, and RNN and LSTM with 0.57 and 0.45 respectively. The high performance of CNN is due to its ability to effectively capture spatial patterns in vibration data which is crucial for fault diagnosis in rotating machinery followed by MLP due to its faster convergence during training. However, when scaling the data, MLP outperformed CNN, demonstrating superior adaptability to increased data complexity and volume. Due to the need for larger datasets and temporal patterns in the vibration data, which RNN and LSTM are designed to handle, they resulted in a lower accuracy. This study shows that CNN has given better results than other deep learning algorithms MLP, RNN, and LSTM in fault diagnosis of rotating machinery. Future research could explore the application of these techniques to different types of machinery and fault conditions.

The Open Access (OA) publishing model that is based on article processing charges (APC) is often associated with the potential for more transparency regarding the expenditures for publications. However, the extent to which transparency can be achieved depends not least on the completeness of data in APC monitoring systems. This article investigates two blind spots of the largest collection of APC payment information, OpenAPC. It aims to identify likely APC-liable publications for German universities that contribute to this system and for those that do not provide data to it. The calculation combines data from Web of Science, the ISSN-Gold-OA-list and OpenAPC. The results show that for the group of universities contributing to the monitoring system, more than half of the APC payments are not covered by it and the average payments for non-covered APCs is higher than for APCs covered by the system. In addition, the group of universities that does not contribute to OpenAPC accounts for two thirds of the number of APC-liable publications recorded for contributing universities. Regarding the size of these blind spots, the value of the monitoring system is limited at present.

(1) Background: Show caves are unique natural attractions and touristic traffic can trigger their degradation within a very short time. There are no universal solutions to counter the effects of the touristic impact upon cave environment and both protection protocols and management plans have to be established on a case-by-case basis; (2) Methods: The study includes four show caves from the Romanian Carpathians, where monitoring of the number of visitors, paralleled by the monitoring of the main physico-chemical parameters of the air and water (CO2, temperature, humidity, drip rate, conductivity, and pH) was implemented; (3) Results and Conclusions: The results of the study has: (i) established a monitoring protocol to be applied to each of the four show caves; (ii) established a set of basic principles to be enforced by the management of show caves; (iii) issued a set of preventive measures and instructions to be followed by the personnel and stakeholders of the caves.

Condition monitoring of bearings is an open issue. The use of the stator current to monitor induction motors has been validated as a very advantageous and practical way to detect several types of faults. Nevertheless, for bearing faults the use of vibrations or sound generally offers better results in the accuracy of the detection although with some disadvantages related to the sensors used for monitoring. To improve the performance of bearing monitoring, it is proposed to take advantage of more information available in the current spectra, beyond the usually employed, incorporating the amplitude of a significant number of sidebands around the first eleven harmonics, growing exponentially the number of fault signatures. This is especially interesting for inverter-fed motors. But, in turn, this leads to the problem of overfitting when applying a classifier to perform the fault diagnosis. To overcome this problem, and still exploit all the useful information available in the spectra, it is proposed to use shrinkage methods, which have been lately proposed in machine learning to solve the overfitting issue when the problem has much more variables than examples to classify. A case study with a motor is shown to prove the validity of the proposal

Background: Cell-free DNA (cfDNA) analysis has become a promising tool for diagnosis, prognosis and monitoring of lymphoma cases. Until now, research in this area has mainly focused in aggressive lymphomas with scanty information from other lymphoma subtypes. Methods: We selected 256 patients diagnosed with lymphomas including a large variety of B-cell and T-cell non-Hodgkin and Hodgkin lymphomas and quantified cfDNA from plasma at the time of diagnosis. We further selected 49 large B cell lymphomas (LBCL) and analyzed cfDNA levels at diagnosis (pre-therapy) and after therapy. In addition, we performed NGS in cfDNA and tissue in this cohort of LBCL. Results: Lymphoma patients showed a statistically significant higher cfDNA concentration than healthy controls (mean 53.0 ng/mL vs 5.6 ng/mL, p <0.001). The cfDNA concentration correlated with lymphoma subtype, lactate dehydrogenase, International Prognostic Index (IPI) score, Ann Arbor (AA) and B-symptoms. In 49 LBCL cases, the cfDNA concentration decreased after therapy in cases who achieved complete response (CR), and increased in non-responders. The median cfDNA at diagnosis of patients who achieved CR and later relapsed was higher (81.5 ng/mL) compared with levels of those who did not (38.6 ng/mL). A concordance of 84% was observed between NGS results in tumor and cfDNA samples. Higher VAF in cfDNA correlated with advanced stage and bulky disease. Conclusions: cfDNA analysis can be easily performed in almost all lymphoma cases. The cfDNA concentration correlated with the characteristics of aggressiveness of the lymphomas and in LBCL with the response achieved after therapy. These results support the utility of cfDNA analysis as a complementary tool in the management of lymphoma patients.

Monitoring is an essential component in ecosystem management and leveraging existing data sources for multiple species of interest can be one effective way to enhance information when making management decisions. Here we analyzed juvenile Chinook Salmon (Oncorhynchus tshawytscha) bycatch data that has been collected by the recently established Enhanced Delta Smelt Monitoring program (EDSM), a survey designed to estimate the abundance and distribution of the San Francisco Estuary’s (estuary) endangered Delta Smelt (Hypomesus transpacificus). Two key aspects of the EDSM program distinguish it from other fish surveys in the estuary: a stratified random sampling design and the spatial scale of its sampling effort. We integrated the EDSM dataset with other existing surveys in the estuary and used an occupancy model to assess detection probability differences across gear types. We saw no large-scale differences in size selectivity, and while detection probability varied among gear types, cumulative detection probability for EDSM was comparable to other surveys due to the program’s use of replicate tows. Based on our occupancy model and sampling effort in the estuary during spring of 2017 and 2018, we highlighted under-sampled regions that saw improvements in monitoring coverage due to EDSM. Our analysis also revealed that each sampling method has its own benefits and constraints. Although the use of random sites with replicates as conducted by EDSM can provide more statistically robust abundance estimates relative to traditional methods, the use of fixed stations and simple methods such as beach seine may provide a more cost-effective way of monitoring salmon occurrence in certain regions of the estuary. Stronger inference on salmon abundance and distribution can be made by leveraging the strengths of each survey’s method. Careful consideration of these trade-offs is crucial as the management agencies of the estuary continue to adapt and improve their monitoring programs.

This paper presents a comprehensive review of the transformative impact of 3D printing technology on smart cities. As cities face rapid urbanization, resource shortages, and environmental degradation, innovative solutions such as additive manufacturing (AM) offer potential pathways for sustainable urban development. By synthesizing 66 publications from 2015 to 2024, the study examines how 3D printing improves urban infrastructure, enhances sustainability, and fosters community engagement in city planning. Key benefits of 3D printing include reducing construction time and material waste, lowering costs, and enabling the creation of scalable, affordable housing solutions. The paper also addresses emerging areas such as the integration of 3D printing with digital twins (DT), machine learning (ML), and AI to optimize urban infrastructure and predictive maintenance. It highlights the use of smart materials and soft robotics for structural health monitoring (SHM), and repairs. Despite the promising advancements, challenges remain in terms of cost, scalability, and the need for interdisciplinary collaboration among engineers, urban planners, and policymakers. The findings suggest a roadmap for future research and practical applications of 3D printing in smart cities, contributing to the ongoing discourse on sustainable and technologically advanced urban development.

Detecting volatile organic compounds (VOCs) emitted from different plant species and their or-gans can provide valuable information about plant health and environmental factors that affect them. For example, limonene emission can be a biomarker to monitor plant health and detect stress. Traditional methods for VOC detection encounter challenges, prompting the proposal of novel approaches. In this study, we proposed integrating electrospinning, molecular imprinting, and conductive nanofibers to fabricate limonene sensors. In detail, polyvinylpyrrolidone (PVP) and polyacrylic acid (PAA) served here as fiber and cavity formers, respectively, with multi-walled carbon nanotubes (MWCNT) enhancing conductivity. We developed one-step monolithic molecularly imprinted fibers, where S(-)-limonene was the target molecule using electrospinning technique. The functional cavities were fixed using UV curing method, followed by a target mol-ecule washing. This procedure enabled the creation of recognition sites for limonene within the nanofiber matrix, enhancing sensor performance and streamlining manufacturing. Humidity was crucial for sensor working, with optimal conditions at about 50% RH. The sensors rapidly re-sponded to S(-)-limonene, reaching a plateau within 200 seconds. Enhancing fiber density im-proved sensor performance, resulting in a lower limit of detection (LOD) of 137 ppb. However, excessive fiber density decreased accessibility to active sites, thus reducing sensitivity. Remarka-bly, the thinnest mat on the fibrous sensors created provided the highest selectivity to limonene (Selectivity Index: 72%) compared to other VOCs, such as EtOH (used as a solvent in nanofiber development), aromatic compounds (toluene), and two other monoterpenes (α-pinene and linalo-ol) with similar structure. These findings underscored the potential of the proposed integrated approach for selective VOC detection in applications such as precision agriculture and environ-mental monitoring.

Post-evaluation of ecological redevelopment is a good method for its achievements. The eco-engineering technologies and achievements of landscape water reconstructed from aquaculture ponds in Shanghai Chenshan Botanical Garden have been introduced in this study. The sediments and water quality were also sampled and tested for basic physicochemical parameters and heavy metal concentration. The ecological redevelopment of landscape water reconstructed from aquaculture ponds was evaluated using the Nemero comprehensive pollution index method. The results shown that nutrients including organic matter, organic nitrogen and their ratio of sediment were found to be in a state of moderate pollution, while their ecological risk of heavy metals was low. Although total nitrogen and total phosphorus of water quality was really higher than that of other indexes, the decline trends of ammonia nitrogen, total nitrogen and total phosphorus was obvious presented over time. In general, this is a good example that redevelopment of water ecosystems from aquaculture ponds using eco-engineering technologies.

This review article explores the transformative impact of Artificial Intelligence (AI) on glaucoma care, focusing on advancements in diagnosis, monitoring, and treatment algorithms. AI technologies have revolutionized the field of ophthalmology by enhancing the accuracy and efficiency of diagnosing glaucoma. Furthermore, AI-powered monitoring systems enable continuous and personalized patient care, facilitating early detection of disease progression. Integrating AI algorithms in treatment protocols promises individualized and optimized therapeutic strategies for better management of glaucoma. This comprehensive review elucidates AI applications' current state and future directions in transforming glaucoma care, emphasizing the potential benefits of improving patient outcomes.

Objectives: To investigate the value of early lactate dynamic monitoring index in predicting prognosis of patients with sepsis and septic shock. Methods: We performed our test on 50 patients. Out of 50 patients, 28 are male, and 22 are female. Prospectively studied pediatric patients with septic shock were performed. Vital signs, Lactate clearance, were obtained at presentation 6 h, 12 h, 24 h over the first 48 h of hospitalization. The therapy received, outcome parameters of mortality and duration of hospitalization were recorded. Results: The statistical data and comparative analysis showed that an average of 16.88 days after admission, 5 patients have died, 17 patients are poorly prognosis leaves the hospital, and the remaining 28 are recovered and discharged. The primary outcome variable of mean 16 days hospitalization mortality rate was 10%. Poor prognosis 34% and fully recovery 56 % were observed. In this retrospective cohort study, a lactate level of more than 2.5mmol/L was the best threshold to predict 28-day mortality among severe sepsis and septic shock patients. In our research, we found mean LC 6 h 3.08mmol/L, and after 48 h mean it is 1.79mmol/L. Significant LC 6 h found, which is 8.08mmol/L in the death group patient where 48 h mmol/L shows significant high. Poor prognosis also presents a clinical increase of lactate level high in the LC 6 h analysis, which is 3.32mmol/L. Recovered patients showed a significant improvement after administering treatment depending on the patient organ involvement and good decrease of lactate reports achieved, which is 1.20mmol/L, where admission reports show it was 1.91mmol/L in LC 6 h. Mean Heart rate 94/51mmhg, pulse 119, temperature 39℃, respiratory rate 32.26, and urine output 456 ml recorded during our study. Death patient shows a remarkable detonation of those reports but has a significant clinical report with the recovered patients. Conclusion: The early lactate dynamic monitoring index has a high value in predicting sepsis and septic shock patients' prognosis, thus worth popularizing.

The supply of feed has a significant effect on fish growth and operation costs, making it a critical factor in aquaculture. Owing to the repetitive nature of feed supply, feeding techniques have undergone a shift from manual feeding to systems allowing operators to set feed quantities and timing, reducing labor efforts. However, unlike manual feeding, automatic systems cannot ad-just the amount of feed supplied according to the feeding activities of fish, potentially resulting in overfeeding or underfeeding. Such overfeeding causes marine pollution and increases operational costs, whereas underfeeding hinders fish growth. In this paper, we present an intelligent feeding system that observes the depth-specific feeding behavior of red seabream during the feeding process and determines whether feed supply must be continued. The performance of the feeding algorithm is evaluated by comparing the feed loss rate measured during a feeding experiment at a red seabream sea cage farm with that of the traditional manual feeding method. The results reveal that the feed supply per unit time of the manual method and the developed intelligent feed supply system is at an equivalent level. Moreover, the difference in the average feed loss rate is a negligible 1.16%, confirming that the new system is slightly more advantageous.

Due to the inherent risks associated with tunnel construction, including potential collapse, various types of work activities, and challenging visibility and communication conditions, safety management in tunnel projects requires significant investment in terms of cost and time. In this research, we propose and demonstrate a novel smart construction system that utilizes worker location monitoring technology to enhance safety in tunnel construction. The system comprises a wearable beacon integrated into safety helmets, scanners strategically placed at regular intervals inside the tunnel, environmental sensors for monitoring temperature, pressure, and air quality, and mobile devices for collecting and analyzing data on workers and the environment. Through a field demonstration conducted in a Korean tunnel construction site, we validated the effectiveness of the proposed system, which demonstrated real-time monitoring of workers and reliable communication capabilities, leading to improved safety and cost-efficiency in tunnel construction. By implementing the proposed system, we achieved a significant reduction of 37% in monthly construction costs and 77% in annual construction costs compared to conventional methods.

Influenced by geological, climatic, and natural weathering factors, the Great Wall heritage is sus-ceptible to deformations, posing significant challenges to the comprehensive preservation of the Great Wall sites. To investigate techniques for monitoring deformations in extensive linear cultural heritage sites, such as the Great Wall, this study utilizes the SBAS-InSAR technique for deformation monitoring and analysis. A dataset comprising 161 Sentinel-1A images spanning from March 2017 to January 2022 was chosen for SBAS-InSAR processing, yielding a deformation velocity field. To verify result credibility, a typical mountainous segment spanning approximately 896.53 km within the Great Wall landscape corridor underwent analysis. The findings suggest that around 75.8% of the landscape corridor along the Shanxi section of the Ming Great Wall maintain relative stability, displaying deformation rates varying from -10 to 10 mm/year. The remaining 24.2% of the land-scape corridor experiences notable deformations, including a maximum subsidence rate of 33.1 mm/year and a maximum subsidence of 148.6 mm. This study illustrates the potential utility of the SBAS-InSAR technique for monitoring and evaluating surface deformations in extensive linear cultural heritage sites.

Operational weather and also flood forecasting has been performed successfully for decades and is of great socioeconomic importance. Up to now, forecast products focus on atmospheric variables, such as precipitation, air temperature and, in hydrology, on river discharge. Considering the full terrestrial system from groundwater across the land surface into the atmosphere, a number of important hydrologic variables are missing especially with regard to the shallow and deeper subsurface (e.g. groundwater), which are gaining considerable attention in the context of global change. In this study, we propose a terrestrial monitoring/forecasting system using the Terrestrial Systems Modeling Platform (TSMP) that predicts all essential states and fluxes of the terrestrial hydrologic and energy cycles from groundwater into the atmosphere. Closure of the terrestrial cycles provides a physically consistent picture of the terrestrial system in TSMP. TSMP has been implemented over a regional domain over North Rhine-Westphalia and a continental domain over European in a real-time forecast/monitoring workflow. Applying a real-time forecasting/monitoring workflow over both domains, experimental forecasts are being produced with different lead times since the beginning of 2016. Real-time forecast/monitoring products encompass all compartments of the terrestrial system including additional hydrologic variables, such as plant available soil water, groundwater table depth, and groundwater recharge and storage.

To make wind power more competitive, it is necessary to reduce turbine downtime and reduce costs associated with wind turbine Operation and Maintenance (O&amp;M). Incorporating machine learning in developing condition-based predictive maintenance methodologies for wind turbines can enhance their efficiency and reliability. This paper presents a monitoring method that utilizes Base Density for the Support Vector Machine (BDSVM) and the evolutionary Fourier spectra of vibrations. This method allows smart monitoring of the function evolution of the turbine. A complex optimal function (FO) for 5-degree order has been developed that will be the boundary function of the BDSVM to timely determine the magnitude, frequency, and place of the failure occurring in wind turbine drive.

The green biomass of horticultural plants contains valuable secondary metabolites (SM) which can potentially be extracted and sold. When exposed to stress, plants accumulate higher amounts of these SMs, making the extraction and commercialization even more attractive. We evaluated the potential for accumulating of the flavones cynaroside and graveobioside A in leaves of two bell pepper cultivars (Mavras and Stayer) when exposed to salt stress (100 mM NaCl), UVA/B excitation (UVA 4-5 W/m²; UVB 10-14 W/m² for 3 hours per day) or a combination of both stressors. HPLC analyses proved the enhanced accumulation of both metabolites under stress conditions. Cynaroside accumulation is effectively triggered by high-UV stress, whereas graveobioside A contents increase under salt stress. Highest contents were observed in plants exposed to combined stress. Effects of stress on overall plant performance differed significantly between treatments, with least negative impact on aboveground biomass found for high-UV stressed plants. The usage of two non-destructive instruments (Dualex and Multiplex) allowed us to gain insights in ontogenetical effects at the leaf level and temporal development of SM contents over time. Indices provided by those devices correlate fairly with amounts detected via HPLC (Cynaroside: R2 = 0.46 – 0.66; Graveobioside A: R2 = 0.51 – 0.71). The concentrations of both metabolites tend to decrease at leaf level during the ontogenetical development even under stress conditions. High-UV stress is a promising tool for enriching plant leaves with valuable SM without major effects on plant biomass. All data is available online [1].

Background/Objectives: Heart failure (HF) is a chronic disease with a steadily increasing prevalence, high mortality, social and economic costs. Furthermore, every hospitalisation for acute HF is associated with worsening prognosis and reduced life expectancy. In order to prevent hospitalisations, it would be useful to have instruments that can predict them well in advance. Methods: We performed a review on remote monitoring of heart failure through implantable devices.; Results: Precise multi-parameter algorithms, available for ICD and CRT-D patients, have been created, which also use artificial intelligence and are able to predict a new heart failure event more than 30 days in advance. There are also implantable pulmonary artery devices that can predict hospitalisations and reduce the impact of heart failure. proper organisation of transmission and alerts management is crucial for clinical success in using these tools. Conclusions: The full implementation of remote monitoring of implantable devices and in particular the use of new algorithms for the prediction of acute heart failure episodes represents a huge challenge but also a huge opportunity.

Wearable technology will become available and allow prolonged electroencephalography (EEG) monitoring in the home environment of patients with epilepsy. Neurologists analyse the EEG visually and annotate all seizures, which patients often under report. Visual analysis of a 24 hour EEG recording typically takes one to two hours. Reliable automated seizure detection algorithms will be crucial to reduce this analysis. We study a dataset of behind-the-ear EEG measurements. Our first aim was to develop a methodology to reduce the EEG dataset by classifying part of the data automatically, while retaining 100% detection sensitivity (DS). Prediction confidences are determined by temperature scaling of the classification model outputs and trust scores. A DS of approximately 90% (99%) can be achieved when automatically classifying around 90% (60%) of the data. Perfect DS can be achieved when automatically classifying 50% of the data. Our second contribution demonstrates that a common modelling strategy, where predictions from several short EEG segments are used to obtain a final prediction, can be improved by filtering out untrustworthy segments with low trust scores. The false detection rate shows a relative decrease between 21% and 43%, and the DS shows a small increase or decrease.

A temporary monitoring system was installed on the 175-years-old historical Széchenyi chain bridge under its reconstruction process. The bridge is in the downtown area of the capital city of Hungary and plays a significant role in city life of Budapest. Six-month-long measurements were conducted during the reconstruction process of the bridge, yielding crucial insights into the structural behaviour of the historical structure. Measurement results were evaluated; the findings encompass the rotation capacity of pins between chain elements, and structural response to temperature changes. This information helped the decision-making of designers and construction company during the reconstruction made between 2021 and 2023. For instance, daily temperature fluctuations result in increased bending moments in the chain elements, rising up to 158% compared to the values observed during a proof load test in 2018. Furthermore, the measurements reveal an approximate 42% increase in normal forces compared to the proof load test, which highlights the high sensitivity of chain bridges to temperature fluctuations, where geometric stiffness plays a crucial role. Reconstruction, reducing self-weight, notably intensifies the impact on normal forces and bending moments. These outcomes strongly emphasize the dominance of dead load and self-weight in the case of chain bridges.

Prevalence estimates of Parkinson’s disease (PD) – the fastest growing neurodegenerative disease – are underestimated due to issues surrounding diagnostic accuracy, symptomatic undiagnosed cases, suboptimal prodromal monitoring, and limited screening access. Remotely monitored wearable devices and sensors provide precise, objective, and frequent measures of motor and non-motor symptoms. Here, we used consumer-grade wearable device and sensor data from the WATCH-PD study to develop a PD screening tool aimed at eliminating gaps between patient symptoms and diagnosis. Early-stage PD (n=82) and age-matched comparison (n=50) participants completed a multidomain assessment battery during a one-year longitudinal multicenter study. Using disease- and behavior-relevant feature engineering and multivariate machine learning modeling of early-stage PD status, we developed a highly accurate (92.3%), sensitive (90.0%), and specific (100%) Random Forest classification model (AUC=0.92) that performed well across environmental contexts. These findings provide robust support for further exploring consumer-grade wearable devices and sensors for global population-wide PD screening and surveillance.

Deck inclination and vertical displacements are among the most important technical parameters to evaluate the health status of a bridge and to verify its bearing capacity. Several methods, both conventional and innovative, are used for structural rotations and displacement monitoring; no one of these does allow, at the same time, precision, automation, static and dynamic monitoring without using high cost instrumentation. The proposed system uses a common laser pointer and image processing. The elastic line inclination is measured by analyzing the single frames of a HD video of the laser beam imprint projected on a flat target. For the image processing, a code was developed in Matlab® that provides instantaneous rotation and displacement of a bridge, charged by a mobile load. An important feature is the synchronization of the load positioning, obtained by a GNSS receiver or by a video. After the calibration procedures, a test was carried out during the movements of a heavy truck maneuvering on a bridge. Data acquisition synchronization allowed to relate the position of the truck on the deck to inclination and displacements. The inclination of elastic line was obtained with a precision of 0.01 mrad. The results demonstrate the suitability of the method for dynamic load tests, control and monitoring of bridges.

Drought is considered one of the severest natural disasters and it is difficult to predict it. This review article aimed to display the state of the art of methods used to predict and monitor types of droughts. We examine more than 30 indices and models to identify the strengths and weaknesses of methods and identify gaps remaining in this field. Examples of examined indies are Palmer Drought Severity Index (PDSI), Standardized Precipitation Index (SPI), and Standardized Precipitation Evapotranspiration Index (SPEI). The research found improvement in drought modeling, however, more focus and improvement are required to monitor and predict drought types. It also found that some methods outperform others such as PDSI, SPI, SPEI, EVI, NDVI, NDWI, VCI and TCI.

Plankton monitoring by microscopy offers long-term ecological perspective of plankton communities but is biased towards those organisms that can be distinguished using the microscope. Genetic identification of marine plankton has become standard but is still not used. This study is a comprehensive study genetically measured taxa in the Western Channel of UK using a small-volume automated water sampler deployed on the CPR platform. The study present one year of high-throughput sequencing data focussing on smaller plankton and separate community to that measured by microscopy that can complement each other for a holistic view of plankton. Quantitative tests of two harmful algae show relatively high abundance of the Pelagophyte Aureococcus anophagefferens during 2011 with low nitrite levels. Three years of Pseudo-nitzschia delicatissima quantitative monitoring also shows a greater abundance of this potentially harmful taxa in 2011. Flow cytometry reveals distinct seasonal cycles with distinct timings.