Cement production contributes to about 7% of CO2 emissions into the atmosphere. Despite our best efforts, we cannot find a competitive substitute that is both reliable and environmentally friendly. The simplest way to solve the problem is to rationalize the resources and try to minimize its use by substitute them with other materials. A concrete that contains a substantial amount of fly ash is already available, but its use is limited by the current shortage in the market and reduced initial resistance. In this context, ternary mixtures have been used to conduct an experiment. A significant volume of cement has been replaced with fly ash and metakaolin, which serves as a correction factor for the performance. In this work the main advantages and disadvantages of the simultaneous use of these two additions, which may reveal to be very interesting with high volumes of substitution will be presented. The performance of this ternary mixture is very promising. Provide a wide range of possibilities for replacing cement, maintaining or even improving its mechanical and durability properties. A solution for an ecological concrete with enhanced performance for general use in construction as an alternative to conventional concrete.

Utilizing NCEP/NCAR monthly reanalysis data alongside precipitation observations from 1936 monitoring stations across China spanning from 1966 to 2022, this study establishes a location index for the thermal low-pressure center situated over the Qinghai–Tibet Plateau. Temporal variations in the location index and summer (July) precipitation patterns in China were studied. Over the past six decades, thermal low-pressure centers have been predominantly positioned near 90°E and 32.5°N on the plateau, with their distribution extending from east to west rather than from south to north. The longitudinal and latitudinal position indices exhibit contrasting linear trends, with a positive trend observed during the 1970s and early 21st century and a negative trend in subsequent decades. Mutation analysis highlights pronounced weakening mutations occurring in 1981 and 1973, with the longitudinal index transitioning from an inter-annual cycle of approximately 6-8 years, while the latitudinal index displays quasi-cyclic oscillations of 5 and 8 and 12-14 years. Strong negative correlations are evident between the location indices and precipitation along the southeastern edge of the Qinghai–Tibet Plateau and in Southern China, contrasting with the positive correlations observed in the central-eastern plateau, northwest China, North China, and the Huang-Huai region. The influence of southerly airflow predominates over much of China east of the plateau, while northwest China experiences convergence between northerly and southerly airflow. Higher location indices correspond to weaker surface cold air masses and strengthened Western Pacific Subtropical and South Asian Highs south of the Yangtze River Basin, resulting in significantly reduced rainfall in the southern Yangtze River region and increased rainfall in northwest China.

Abstract: Purpose: High-grade isthmic spondylolisthesis (HGISL) is a severe condition, associated with low-back pain (LBP) and radiculopathies. The present study is a monocentric prospective observational study investigating the clinical-radiological outcomes of a bilateral minimally invasive TLIF (bm-TLIF) for HGISL. Material and Methods: Patients who underwent bm- TLIF for HGISL at our institution, were considered for inclusion. Clinical-radiological outcomes and complications were collected. Results: Twenty-one patients (14M:7F) were included and the mean clinical follow-up (FU) time was 27(±6) months. There was a significative improvement of the mean VAS-back, VAS-legs, ODI, and SF-36 PCS scores, comparing pre- and last FU measurements. The mean pelvic tilt (p0,05). The univariate analysis showed that residual slip angle (> or  10°) may independently influence VAS-b (p

As a major coal country, China faces the issue of significant gas emissions during the coal mining process. This study aims to improve the utilization efficiency of mine gas, reduce greenhouse gas emissions, and promote the low-carbon and green transformation of the coal industry. A 10kW gas regenerative thermal oxidation (RTO) experimental system was constructed. The effects of initial methane concentration, low-temperature flue gas proportion, and operating load on combustion temperature, methane oxidation rate, high-temperature flue gas energy, and system thermal efficiency were studied. The results show that when the combustion temperature is below 600°C, the CH4 combustion reaction cannot proceed effectively, and the system temperature continuously decreases and cannot be maintained stable. The experiment determines the stable operating methane concentration range of RTO. In this experimental system, the lower limit of the initial methane concentration is 0.28%, corresponding to an 86% methane oxidation rate. As the initial methane concentration decreases, the combustion temperature also decreases, and the methane oxidation rate follows suit. The higher the low-temperature flue gas proportion, the higher the combustion temperature, and the system thermal efficiency and output heat decrease with the increase of the low-temperature flue gas proportion. This experiment explores multiple factors affecting regenerative thermal oxidation, providing an basis for ensuring the safe and stable operation of the system and optimization. Improving the thermal insulation and heat exchange performance of the storage body can expand the lower limit of the initial methane concentration, thereby increasing the stability and thermal efficiency of the system.

A multicenter, prospective cohort study conducted in 5 physiotherapy clinics in the UAE from January 2021 to March 2023 to assess coronal lumbar spine radiographic parameters as a predictor of conservative therapy outcomes in patients suffering from low back and leg pain due to lumbar disc herniation (HNP). Ninety patients (mean age 44 yrs., 54% male) with lumbar HNP underwent conservative therapy. All participants received lumbar spine MRI and radiography to assess spine alignment. Interventions included specific exercises, diathermy, traction, education, a home-based exercise pro-gram, and medications. Detailed demographic data was collected. Follow-up was 6-months after discharge. A successful outcome was based on a minimum of the following four outcomes: (1) reduction of pain by 17.5 points (0–100 NRS); (2) fatigue reduction by 7.5 points; (3) distress reduction by 5 points; and (4) interference reduction by 9.5 points. At 6-month follow-up it was found that patient age, education, and radio-graphic determined lumbosacral angle measures significantly affected the odds of a successful outcome. Increasing age 1-year significantly decreased the odds of success of improving pain, fatigue (OR = 0.85, p = 0.016) and interference scores (OR = 0.89, p = 0.042) by 15%, 15%, and 11% respectively. Lower education significantly increased the odds of success for improving pain, fatigue, and interference by 26.18, 26.18, and 7.5 (p = 0.006, = 0.006, and = 0.029 respectively). Increasing (worsening) the radiographic lumbosacral angle by each 1° significantly reduced the odds of success for improving pain, fatigue, distress, and interference by 3.52, 3.52, 27.99, and 2.55, respectively (p < 0.001, < 0.001, = 0.003, = 0.001). Our findings indicate that younger age, less education, and better coronal radiological lumbar spine alignment all had a substantial impact on the likelihood of success of 6-month outcomes in patients suffering from chronic lower back pain and radiculopathy due to HNP.

Greenhouse gas (GHG) emissions from human activities have climbed significantly above pre-pandemic levels and reached record highs that unequivocally accelerate global warming. Industry has a significant impact on climate change, emitting at least 21 % of global GHGs and making little overall progress toward its reduction until now. Reducing industry’s emissions requires coordinated action along the value chains in order to promote mitigation options, such as energy and material efficiency, circular material flows, and transformative changes within production processes. The authors analyzed the GHG emissions generated during the manufacturing of three different products of automotive suppliers located in Austria. Despite previous efforts toward an environmentally compatible fabrication, additional and significant reduction potentials were identified. These measures for product carbon footprint (PCF) reduction included the sourcing of low-carbon materials (which are already available on the market), more extensive use of renewable energy, and changes towards more resource efficient manufacturing processes and machinery. Depending on the materials used, the PCF can be reduced by up to 80 %. The findings serve to prepare for future PCF reporting regulations and illustrate reduction potentials to achieve future market advantages, especially when PCFs become an awarding criterion.

Previous studies on the mechanisms underlying willed actions reported that the premotor cortex may be involved in the construction of motor awareness. However, its exact role is still under investigation. Here we investigated the role of the dorsal premotor cortex (PMd) in motor awareness by modulating its activity applying inhibitory rTMS to PMd, before a specific motor awareness task (under three conditions: without stimulation, after rTMS and after sham stimulation). During the task, subjects had to trace straight lines to a given target, receiving a visual feedback of the line trajectories on a computer screen. Crucially, in most trials the trajectories on the screen were deviated and to produce straight lines, subjects had to correct their movements towards the opposite direction. After each trial, participants were asked to judge whether the line seen on the computer screen corresponded to the line actually drawn. Results show that participants in the no stimulation condition did not recognize the perturbation until 14 degrees of deviation. Importantly, active, but not sham, rTMS significantly modulated motor awareness, decreasing the amplitude of the angle at which participants became aware of the trajectory correction. These results suggest that PMd plays a crucial role in action self- monitoring.

The study of velocimetry is important for characterizing and comprehending the effects of fluid flow, and the Particle Image Velocimetry (PIV) technique is one of the primary approaches for understanding the velocity vector field in a test section. Commercial PIV systems are expensive, with one of the main cost factors being high-speed camera equipment capable of capturing images at high frames per second (fps), rendering them impractical for many applications. This study proposes an evaluation of utilizing smartphones as image acquisition systems for PIV technique application. An experimental setup inspired by the known angular displacement of synthetic particles is proposed. A stepper motor rotates a plate containing an image of synthetic particles on its surface. The motion of the plate is captured by the smartphone camera, and the images are processed using PIVlab-MatLab® software. The use of two smartphones is assessed, with acquisition rates of either 240 fps or 960 fps and varying angular velocities. The results were satisfactory for velocities up to 0.7 m/s at an acquisition rate of 240 fps and up to 1.8 m/s at 960 fps, validating the use of smartphones as a cost-effective alternative for the PIV technique.

Worldwide, 200 million children experience disability, with the vast majority living in low and middle-income countries. The United Nations Convention on the Rights of the Child (CRC) places great importance on the rights of all children for the opportunities for survival, growth, health, and development. A subsequent document, the UN Convention on the Rights of Persons with Disabilities (CRPD) identifies children with disabilities as rights bearers, who should be considered in all policies and programming worldwide. Nigeria, in 1991 and 2010 ratified the CRC and the CRPD respectively. Nonetheless, knowledge of the extent to which their disability and child-directed policies are considered by these two key conventions remains limited. This study examined the extent to which Nigeria’s current disability and childhood policies have integrated the two normative frameworks from the UN. Using a structured search of databases and Nigerian federal and state government websites, we conducted a policy review to identify their disability and child-related disability policies. We also included the CRC and CRPD reports submitted by the Nigerian government to the United Nations Office of the High Commissioner for Human Rights (OHCHR) (2008 &amp; 2010 cyclical year). A thematic analysis, based on the CRC and CRPD report, identified the following six themes: participation, support systems, awareness-raising, factors associated with adherence to the CRC, laws &amp; rights, and services. The review showed that the available Nigerian disability policies were federal, with some state policies which aligned with the CRC and CRPD. Also identified was the lack of disability policies specific to children and their families. We concluded that, to ensure proper inclusion of the rights of all children, including those with disabilities, in Nigeria there is a need for a more optimal uptake of recommendations of the CRC and CRPD as laid out by the UN.

Low back pain (LBP) is a common musculoskeletal complaint that can impede physical function and mobility. Current management often involves pain medication, but there is a need for non-pharmacological and non-invasive interventions. Soft tissue manipulation (STM) such as massage has been shown to be effective in human subjects, but the molecular mechanisms underlying these findings are not well understood. In this paper, we evaluated potential changes in soft tissue levels of more than thirty pro- or anti-inflammatory cytokines following instrument-assisted STM (IASTM) in rats with chronic, induced LBP using Complete Freund’s Adjuvant. Our results indicate that IASTM is associated with reduced soft tissue levels of RANTES/CCL5 and increased soft tissue levels of IL-4, which are pro-inflammatory and anti-inflammatory factors, respectively, by 120 minutes post-treatment. IASTM was not associated with tissue-level changes in CXCL5/LIX (the murine homologue of IL-8), CXCL7, GM-CSF ICAM-1, IL1-ra, IL-6, IP-10/CXCL10, L-selectin, TNF-α, or VEGF at either 30- or 120 minutes post-treatment. Combined, our findings suggest that IASTM exerts tissue-level effects that are associated with improved clinical outcomes and potentially beneficial changes in pro/anti-inflammatory cytokines in circulation and at the tissue level.

Cumulative exposure to multiple early life stressors are expected to affect behavioral development causing increased susceptibility towards neuropsychiatric disorders. The present study was designed to mimic such conditions in rat model to study behavioral impairments during adolescence and adulthood. Female Wistar rats (n=32; 140-150 gm) were switched to low protein (LP; 8% protein) or Control (20% protein) diet, 15 days prior to conception and then diet regime was maintained throughout the experimental period. Pups born to Control and LP dams were intraperitoneally injected with deltamethrin (DLT-pyrethroid insecticide; 0.7mg/kg body weight; PND 1 to 7) or lipopolysaccharide (LPS-bacterial endotoxin; 0.3mg/kg body weight; PND 3 and 5) or DLT+LPS, on designated days forming 8 experimental groups (Control, LP, Control+LPS, LP+LPS, Control+DLT, LP+DLT, Control+DLT+LPS and LP+DLT+LPS). Neurobehavioral assessments were performed in F1 rats (1, 3, 6 months) by Open field, Elevated plus maze, Light and Dark box, and Rotarod tests. LP rats were found to be more susceptible to either singular or cumulative exposure as compared to their age matched control counterparts, showing significantly severe behavioural abnormalities, as hyperactivity, attention deficits, impulsiveness and low anxiety, the hallmark symptoms of neuropsychiatric disorders like schizophrenia and ADHD, suggesting thereby that early life multi-hit exposure may predispose individuals to developmental disorders.

In order to monitor the diversity of terrestrial biomes, the Earth Exploration Satellite Services demand a high data rate for downlink transmissions while sharing their frequency spectrum with, and suffering interferences from, cellular Base Stations. Both highlight the dilemmas of spectral efficiency (bps/Hz) and spectral coexistence. Our research aims to mitigate interference on low orbit satellite downlinks using Cognitive Radio (CR) and Adaptive MODulation and CODing (MODCOD) techniques. To fulfill this: 1) we present CR approaches to enhance spectrum exploitation. Next, 2) we detail Adaptive MODCOD (ACM) technique to increase RF power and spectral efficiencies. Then, 3) we suggest the solution by combining 1) and 2). Afterwards, 4) we analyze it by monitoring the signal to interference plus noise ratio and the CR/MODCOD strategy. Finally, 5) we provide case studies to demonstrate the strategy’s effectiveness through the practical operation of satellite services, and 6) we conduct a bench test of the communication system.

A low-profile broadband dual-polarized antenna is investigated for base station applications. It consists of two orthogonal dipoles, fork-shaped feeding lines, an artificial magnetic conductor (AMC), and parasitic strips. By utilizing the dispersion Brillouin diagram, the AMC is designed as the antenna reflector. It has a wide in-phase reflection bandwidth of 54.7% (1.54-2.70 GHz) and a surface wave bound range of 0-2.65 GHz. This design effectively reduces the antenna profile by over 50% compared to traditional antennas without an AMC. For demonstration, a prototype is fabricated for 2G/3G/LTE base station applications. Good agreement between simulations and measurements is observed. The measured -10-dB impedance bandwidth of our antenna is 55.4% (1.58 –2.79 GHz), with a stable gain of 9.5 dBi and high isolation of more than 30 dB across the impedance passband. As a result, this antenna is an excellent candidate for miniaturized base station antenna applications.

3D printing is commonly used to create complex objects at a low cost. It has also been applied in the fabrication of metamaterials and metasurfaces, which alter the propagation path of electromagnetic waves. These structures have diverse applications, including enhancing beam direction, improving antenna gain and signal-to-noise ratio, and creating filters and reflectors. Metasurfaces are cheap to fabricate and their use is expected to boost antenna efficiency in 5G telecommunications and beyond. However, accurately characterizing their profile remains a significant challenge. This paper presents a low-cost fully automated 4-axis instrument for microwave metasurface charac-terization, overcoming limitations of manual methods and offering an efficient and accurate approach. This research represents a significant advancement in microwave metasurface characterization, enabling sophisticated techniques to advance wireless communication technolo-gies, as it is the case of the future 5G and millimeter-wave communication systems. The equipment has an approximate cost of $1550 USD and was able to characterize a metalens with a focal distance of 20 cm designed for signals at 30 GHz. It was possible to create 2D and 3D profiles of the intensity distribution focused by the metalens and extract parameters such as the gain (8.05 dB), 3dB depth of focus (11 cm) and full width at half maximum (2.17 cm). The comparison of the measurements with the diffraction calculations of the metalens showed a very good agreement between the in-tensity distributions and the parameters of the metalens.

UV induced photoluminescence of organosilica films with ethylene and benzene bridging groups in their matrix and terminal methyl groups on the pore wall surface is studied to reveal optically active defects and understand their origin and nature. Careful selection of the film’s precursors and conditions of deposition and curing, analysis of chemical and structural properties led to the conclusion that luminescence sources are not associated with the presence of oxygen-deficient centers, as in the case in pure SiO2. It is shown that the sources of luminescence are the carbon-containing components that are part of the low-k-matrix, as well as the carbon residues formed upon removal of the template and UV induced destruction of organosilica samples. A good correlation between the energy of the photoluminescence peaks and the chemical composition is observed. This correlation is confirmed by the results obtained by the Density Functional theory. The photoluminescence intensity increases with porosity and internal surface area. The spectra become more complicated after annealing at 400 °C, although Fourier transform infrared spectroscopy does not show these changes. The appearance of additional bands is associated with compaction of low-k matrix and segregation of template residues on the surface of the pore wall.

Low-dimensional carbon-based (LDC) materials have attracted extensive research attentions in electrocatalysis because of their unique advantages such as structural diversity, low cost, and chemical tolerance. They have been widely used in a broad range of electrochemical reactions to relief environmental pollution and energy crisis. Typical examples include hydrogen evolution reaction (HER), oxygen evolution reaction (OER), oxygen reduction reaction (ORR), carbon dioxide reduction reaction (CO₂RR), and nitrogen reduction reaction (NRR). Traditional “trial and error” strategies seriously slowed down the rational design of electrocatalysts for these important applications. Recent studies show that the combination of density functional theory (DFT) calculations and experimental research is capable of accurately predicting the structures of electrocatalysts, thus could reveal the catalytic mechanisms. Herein, current well-recognized collaboration methods of theory and practice are reviewed. The history of modern DFT, commonly used calculation methods, and basic functionals are briefly summarized. Special attention is paid to descriptors that are widely accepted as a bridge links the structure and activity, and the breakthroughs for high-volume accurate prediction of electrocatalysts. Importantly, correlating multiple descriptors are used to systematically describe the complicated interfacial electrocatalytic processes of LDC catalysts. In addition, machine learning and high-throughput simulations are crucial in assisting the discovery of new multiple descriptors and reaction mechanisms. This review will guide the further development of LDC electrocatalysts for extended applications from the aspect of DFT computations.

Background: Cervical cancer is the fourth most common cancer in women globally despite being a largely treatable and preventable malignancy. Developing countries account for over 80% of all new cases of cervical cancer. Women residing in low-resource settings such as those residing in slums have a higher risk of cervical cancer, and lower uptake of cervical cancer screening. Diverse barriers influence the uptake of cervical cancer screening among women in low-resource settings. Objectives: This qualitative study was carried out prior to a cervical cancer screening program and explored women’s knowledge about cervical cancer, and their perceived barriers and recommendations for the program.Method: Four focus group discussions (FGD) were conducted among 35 women between the ages of 21 – 65 years residing in two urban slums in Lagos, Nigeria. Each FGD was limited to 8-10 participants of women of similar ages. Voice recordings were transcribed verbatim and analysis was done using thematic analysis.Results: Most of the women were not aware of cervical cancer and none knew the symptoms or risk factors of cervical cancer. The participants felt that the cervical cancer screening program would be well accepted in the community, however, they expressed concerns about the cost of the screening test and the sex of the person performing the test. The recommendations proffered for a successful cervical cancer screening program include; reducing the cost of the test or providing the test free of charge, having people that speak the local language as part of the team, using female health care providers, using a private location within the community or nearby PHC, and publicizing the program with the use of SMS, phone calls, town crier, and health talks. It was recommended that organizing health education sessions would help improve women’s poorly perceived susceptibility to cervical cancer.Conclusion: Interventions to increase uptake of cervical cancer screening among women in low resource settings need to improve knowledge and understanding of cervical cancer and address the barriers to cervical cancer screening such as cost, distance, and as much as possible, sex of the healthcare provider should be considered.

We present improvements in n-best rescoring of code-switched speech achieved by n-gram augmentation as well as optimised pretraining of long short-term memory (LSTM) language models with larger corpora of out-of-domain monolingual text. In addition, we consider the application of large pretrained transformer-based architectures. Our experimental evaluation is performed on an under-resourced corpus of code-switched speech comprising four bilingual code-switched sub-corpora, each containing a Bantu language (isiZulu, isiXhosa, Sesotho, or Setswana) and English. We find in our experiments that, by combining n-gram augmentation with the optimised pretraining strategy, speech recognition errors are reduced for each individual bilingual pair by 3.51% absolute on average over the four corpora. Importantly, we find that even speech recognition at language boundaries improves by 1.14% even though the additional data is monolingual. Utilising the augmented n-grams for lattice generation, we then contrast these improvements with those achieved after fine-tuning pretrained transformer-based models such as distilled GPT-2 and M-BERT. We find that, even though these language models have not been trained on any of our target languages, they can improve speech recognition performance even in zero-shot settings. After fine-tuning on in-domain data, these large architectures offer further improvements, achieving a 4.45% absolute decrease in overall speech recognition errors and a 3.52% improvement over language boundaries. Finally, a combination of the optimised LSTM and fine-tuned BERT models achieves a further gain of 0.47% absolute on average for three of the four language pairs compared to M-BERT. We conclude that the careful optimisation of the pretraining strategy used for neural network language models can offer worthwhile improvements in speech recognition accuracy even at language switches, and that much larger state-of-the-art architectures such as GPT-2 and M-BERT promise even further gains.

This research refers to the creation of a method of medical technology such as a device that can collect, encode, temporarily store, and transfer electroencephalographic signals from epileptic patients for study and evaluation. For applying the specific apparatus related to neurostimulation technologies such as Deep Brain Stimulation (DBS) and Responsive Neurostimulation (RNS) the approaches followed concern three basic levels. The first level is concerned with initial modelling and creating the template for the following two stages. Further on, the second level is based on developing code for programming integrated circuits and simulation with the appropriate software. The third and final stage is the most substantial, as the transmitter’s construction is attempted at the evaluation level. In particular, more than one software and device are involved in this phase for the most realistic performance of the desired result. However, it is worth noting that the principal goal of this study is to achieve low consumption rates for the device’s complete and smooth operation. As a result, this research aims to evolve this device so that it can send data wirelessly and simultaneously provide energy efficiency.

Global malaria epidemiology has changed in the last decade with a substantial increase in cases and death being recorded. Over 90% of global cases and deaths occur in Sub-Saharan Africa (SSA). Tanzania accounts for about 4% of all cases and deaths reported in recent years. It is believed that several factors contribute to the resurgence of malaria, parasite resistance to antimalarials and mosquito resistance to insecticides being at the top of the list. The presence of sub-microscopic infections poses a significant challenge to malaria rapid diagnostic tests (mRDT), particularly in low-endemic areas. Our cross-sectional surveys in Handeni and Moshi, Tanzania assessed the effect of low parasite density on mRDT. A significant difference (P˂0.001) in malaria prevalence by mRDT, light microscopy (LM) and nested polymerase chain reaction (PCR) was found among age groups. In comparison to all other groups, school-age children (5-15 years) had the highest prevalence of malaria. Based on the results of this study, mRDT may miss up to 6% of cases of malaria mainly due to low-density parasitaemia. Routinely used mRDT will likely miss the sub-microscopic parasitemia which will ultimately contribute to the continued spread of malaria and hinder efforts to control and eliminate it.

During puberty and emerging sexuality, adolescents experience important physical, mental, and social transformations. In the process of dealing with these changes, adolescents can become potentially vulnerable to mental health problems.The aim was to identify and synthesize published research evidence on sexuality-related mental health stressors among adolescent girls and boys, identify gaps (if any) in current knowledge, and contribute to knowledge about the experiences of emerging sexuality and health among adolescents, to further inform research, practice, and policy initiatives in sexual health.A scoping literature review of peer-reviewed articles published between 1990 and 2018. MEDLINE, CINAHL, EMBASE, PsycINFO, Global health, ERIC, and Sociological Abstracts databases were searched for research studies that reported experiences of sexuality related mental health issues and symptomatology of adolescents. We targeted studies conducted with adolescent populations between ages 11-24 years living in LMICs.Data from 12 published research papers, including 8 qualitative studies, 3 quantitative studies, and 1 mixed method study, were systematically analyzed. Four major themes and 4 sub themes were identified regarding sexual health and mental health of adolescents: 1) Relationship of sexuality and mental health; 2) Social and cultural influences; 3) Challenges in seeking sexuality information and services among adolescents; and 4) Educational needs among adolescents related to sexuality; and 4) Educational needs among adolescents related to sexuality. Lack of social support, Unmet needs for accessible adolescent friendly sexual health services, counseling, and age-appropriate information may be associated with several mental health stressors and symptoms, such as sadness, depressive and anxiety symptomatology, regret, fear, embarrassment, low self-esteem, guilt, shame, and anger. Therefore, tackling sexuality-related stressors could play an important role in addressing the overall wellbeing of young people. Future studies need to generate a deeper understanding of the concept of sexual health and its relation to mental health in diverse contexts. Health care professionals need to be aware of sexuality-related experiences of adolescent girls and boys by offering effective youth-friendly sexual and reproductive health education to support overall mental health and improve the experiences of emerging sexuality in adolescents.

Wheat gluten contains epitopes that trigger celiac disease (CD). A life-long strict gluten-free diet is the only treatment accepted for CD. However, very low-gluten wheat may provide an alternative treatment to CD. Conventional plant breeding methods are not sufficient to produce celiac-safe wheat. RNA interference technology, to some extent, succeeded in the development of safer wheat varieties. However, these varieties had multiple challenges in their implementation. Clustered Regularly Interspaced Short Palindromic Repeats-associated nuclease 9 (CRISPR/Cas9) is a versatile gene-editing tool that has the ability to edit the immunogenic gluten genes. So far, only a few studies have applied CRISPR/Cas9 to modify the wheat genome. In this article, we reviewed published literature that applied CRISPR/Cas9 in wheat genome editing to investigate the current status of the CRISPR/Cas9 system to produce a low-immunogenic wheat variety. We found that in recent years, the CRISPR/Cas9 system has been continuously improved to edit the complex hexaploid wheat genome. Although some reduced immunogenic wheat varieties have been reported, CRISPR/Cas9 has still not been fully explored in editing the wheat genome. We conclude that further studies are required to apply the CRISPR/Cas9 gene-editing system efficiently for the development of celiac-safe wheat variety and to establish it as a “tool to celiac safe wheat.”

The paradigm of the Somatic Mutation Theory (SMT) is failing and a new paradigm is in the making but not yet established. What is being challenged is a conceptual approach that involves the entire human biology and the development of chronic diseases. The behavior of breast cancer is well compatible with the concept that the primary tumor is able to control its microscopic metastases, in the same way that an organ (e.g., the liver) is able to control its physiological size. This finding suggested that breast cancer and its metastases may behave as an organoid. The new paradigm under construction considers the origin of tumors as a disturbance in the communication network between tissue cell populations and between cells and extracellular matrix, and supports a systemic approach to the study of both healthy and pathologic tissues. The commentary provides a rationale for the role of physical exercise in the control of tumor dormancy according to a human evolutionary perspective.

Vehicle driveability is one of the important vehicle attributes in range-extender electric vehicles due to the electric motor torque characteristics at low-speed events. The process of validating and rectifying vehicle driveability attributes is typically utilised by a physical vehicle prototype that can be expensive and required several design iterations. In this paper, a model-based energy method to assess vehicle driveability is presented based on a high-fidelity 49 degree-of-freedom powertrain and vehicle systems. Multibody dynamics components were built according to their true centre of gravity relative to the vehicle datum for providing an accurate system interaction. The work covered a frequency at less than 20 Hz. The results that consisted of the component frequency domination are structured and examined to identify the low-frequency sensitivity based on different operating parameters such as a road surface coefficient. An energy path technique was also implemented on the dominant component by decoupling its compliances to study the effect on the vehicle driveability and low-frequency response. The outcomes of the research provided a good understanding of the interaction across the sub-systems levels. The powertrain rubber mounts were the dominant components that controlled the low-frequency contents (< 15.33 Hz) and can change the vehicle driveability quality.

Low back pain (LBP) is a leading cause of disability. It significantly impacts the patient’s quality of life, limits their daily living activities, and reduces work productivity. To reduce the burden of LBP, several pharmacological and non-pharmacological treatment options are available. This review summarizes the role of heat therapy in the management of LBP. First, we outline the common causes of LBP, then discuss the general mechanisms of heat therapy on (LB)P, and finally review the published evidence regarding the impact of heat therapy in patients with acute or chronic non-specific LBP. This review demonstrates that continuous, low-level heat therapy provides pain relief, improves muscular strength, and increases flexibility. Therefore, this effective, safe, easy-to-use, and cost-effective non-pharmacological pain relief option is still relevant in modern clinical practice.

This chapter is written for the welfare of the society, questioning and enlightening the effects of the increment or decrement in the percentage of quality of air causing pollution due to the rise in the traffic post-lockdown due to COVID-19 in metro cities, specifically in Delhi. In this chapter, we address the question about people's preference in moving in the shared taxis to their workplaces or their reluctance and denial of the idea of moving in the shared vehicle because of the fear of getting infected. The sensitivity of the situation will compel the people to move in a single occupied vehicle (SOV). The rise in the number of vehicles on the roads will result in traffic jams and different kinds of pollution where people battling with the pandemic will inevitably get exposed to other health-related issues. We use a BPR (Bureau of Public Roads) model to combat this issue endangering the environment and public health. We exploit the BPR function to relate average travel time to the estimated number of commuters travelling by car. We collect mode share data from the NITI Ayog, the State Resource Centre and other authentic sources, which gives unique figures of the impact of shared mobility in India and how, in its absence, various sectors will get affected. Using the given data and the BPR, we evaluate increased vehicle volumes on the road if different portions of transit and carpool users switch to single-occupancy vehicles and its effect on multiple other factors. Based on the study of densely populated city, Delhi, we predict that cities with significant transit ridership are at risk for extreme traffic and pollution unless transit systems can resume safe with effective protocols.

It is well known that low back pain (LBP) prevalence is high during the course of school age children’s lives. However, literature concerning the initial onset of back pain between ages of 3 and 11 years remains scarce. The present study aimed to analyze the prevalence of LBP in kindergarten and primary school students. 278 (9.9±2.1 years old; 52.2% girls) students from two public kindergarten and primary schools in Valencia, Spain participated in this cross-sectional study. The Nordic questionnaire on LBP was used to ask questions related to the duration of LBP symptoms over time. The lifetime prevalence of LBP was 47.5% (n = 132), a last year prevalence of 44.2% (n = 123), and a last week prevalence of 18.8% (n = 50) was reported. Boys and girls reached lifetime prevalence of 52.3% (n = 64) and 47.7% (n = 82) (χ2 = 1.978, p = .099), respectively. By age group, lifetime episodes of LBP also showed a higher prevalence with increasing age (χ2 = 32.637; p &lt; .001). In summary, our findings suggest that LBP increases with age. In addition, our results further strengthen the evidence that LBP onset could start as young as 10-years-old.

Crystallization is a significant procedure in the manufacturing of many pharmaceutical and solid food products. In-situ Electrical Resistance Tomography (ERT) is a novel Process Analytical Tool (PAT) to provide a cheap and quick way to test, visualize, and evaluate the progress of crystallization processes. In this work, the spatial accuracy of the non-conductive phantoms in low conductivity solutions was evaluated. Gauss-Newton, Linear Back Projection, and iterative Total Variation reconstruction algorithms were used to compare the phantom reconstructions for tap water, industrial-grade saturated sucrose solution, and demineralized water. Cylindrical phantom measuring 10 mm in diameter and a cross-section area of 1.5 % of the total beaker area was detected at the center of the beaker. Two phantoms with a 10 mm diameter were visualized separately in non-central locations. The quantitative evaluations were done for the phantoms with radii ranging from 10 mm to 50 mm in demineralized water. Multiple factors such as ERT device and sensor development, FEM mesh density and simulations, image reconstruction algorithms, number of iterations, segmentation methods, and morphological image processing methods were discussed and analyzed to achieve spatial accuracy. The development of ERT imaging modality for the purpose of monitoring crystallization in low conductivity solutions was performed satisfactorily.

Nowadays, the uses of laser and optics in the medical areas are extremely vivid, especially low-level laser therapy. The light with the wavelength of 633 nm to 1200 nm could penetrate and propagate deep in biological tissue. To develop the low-level laser therapy device, optimizing light delivery is critical to accurately stimulate the biological effects inside the biological tissue. Nevertheless, each form of the tissues at each zone on the body had various refractive optic, absorption, scattering, and anisotropy coefficients. This paper describes the simulation results of low-level laser propagation from skin surface at the lower spine, the knee, the femur and the prostate gland with four wavelengths (633 nm, 780 nm, 850 nm, and 940 nm) by the Monte Carlo method. These simulation results are the base for developing the low-level laser therapy device, that could be used in clinical for treating the fracture, knee osteoarthritis, spinal degeneration, and benign prostatic hypertrophy.

The Oil reservoirs with low permeability account for a large proportion in the world, they surpass half of the total number of the oil reservoirs in China, it is important to exploit this kind of reservoir effectively. The exploitive results of these reservoir using normal water flooding methods are very poor because of the thine pores, bad connections and so on. However, these problems can be well solved by applying gas injection techniques. In this paper, the effects on the recovery effects exerted by the injection parameters such as the oxygen content in the injected air, the injection speed etc. were studied by several experiments using independently designed equipments aiming at one low permeable sandstone reservoir in China. Several conclusions were made from the experiment results: the best recovery effects can be achieved by injecting the oxygen reduced air with 8% of oxygen at the speed of 0.3ml/min (7.41×10-4PV/min) using the methods of injecting the air slugs and the foaming agent slugs alternately; the best oxidation time of the oil was 168 hours and the final oil recovery could be enhanced by 26.5% in this method. It was also showed by the experiments that the larger the permeability ratio is, the larger the recovery factor will be increased. At last, several equations about relationships between the EOR and the air injection parameters were revealed according to the results of the experiments which may offer some references to the LTO process mechanisms study in the similar oil reservoir.

Microsystems are key enabling technologies, with applications found in almost every industrial field, including in-vitro diagnostic, energy harvesting, automotive, telecommunication, drug screening, etc. Microsystems, such as microsensors and actuators, are typically made up of components below 1000 microns in size that can be manufactured at low-unit cost through mass-production. Yet, the development of microsystems for commercial or educational purposes, has typically been limited to upper income countries due to the initial investment costs associated with the microfabrication equipment and processes. However, recent technological advances have enabled the development of low-cost microfabrication tools. In this paper, we describe a range of low-cost approaches and equipment (below £1000), developed or adapted and implemented in our laboratories. We describe processes including photolithography, micromilling, 3D printing, xurography and screen-printing used for the microfabrication of structural and functional materials. The processes that can be used to shape a range of materials with sub-millimetre feature sizes are demonstrated here in the context of Lab-on-Chips, but they can be adapted for other applications. We anticipate that this paper, which will enable researchers to build a low-cost microfabrication toolbox in a wide range of settings, will spark a new interest in microsystems.

This study was conducted to determine the dynamic effects of dietary crude protein (CP) intake on nitrogen (N) balance, ileal amino acid digestibility, and gene expression levels of digestive enzymes at three stages in pigs. In Experiment 1, 18 growing pigs (average body weight (BW) = 9.5 kg) were randomly assigned to one of three treatments (n = 6/treatment group), including normal (20% CP), low (17% CP), and very low (14% CP) protein intake. In Experiment 2, 18 growing pigs (average BW = 30 kg) were allotted randomly to one of three treatments (n = 6/treatment group), including normal (18% CP), low (15% CP), and very low (12% CP) protein intake. In Experiment 3, 18 growing pigs (average BW = 45 kg) were assigned randomly to one of three treatments (n = 6/treatment group), including normal (16% CP), low (13% CP), and very low (10% CP) protein intake. Growing pigs fed the 14% CP and 17% CP diets had lower final BW (P < 0.05) and average daily gain (ADG) (P < 0.05) compared to pigs fed the 20% CP diet. Reducing the dietary CP level from 20 to 14% decreased urinary N excretion by 52.8% (P < 0.001) in Experiment 1. Reducing the dietary CP level from 18 to 12% decreased urinary N excretion by 55.3% (P < 0.001) and reduced fecal N excretion by 34% (P < 0.05) in Experiment 2. Reducing the dietary CP level from 16 to 10% decreased urinary N excretion by 56.4% (P < 0.001) and fecal N excretion by 47.1% (P < 0.001) in Experiment 3. Pigs fed the very low (14%, 12%, and 10% CP) diets showed higher digestibility for CP (P < 0.05), His (P < 0.05), Ile (P < 0.05), Phe (P < 0.05), Thr (P < 0.05), Trp (P < 0.05), Glu (P < 0.05), and Ser (P < 0.05) compared to pigs fed the normal (20%, 18%, and 16% CP) diets among the three experiments. Pigs fed the very low (14%, 12%, and 10% CP) diets showed higher mRNA levels for chymotrypsin C (P < 0.01 in Experiment 1 and 2; P < 0.05 in Experiment 3) compared to pigs fed the normal (20%, 18%, and 16% CP) diets among the three experiments. These results indicated that a reduction in dietary CP by 6% limited the growth performance of growing pigs, and a reduction of dietary CP by 3% supplemented with essential amino acids could reduce the excretion of N into the environment without affecting weight gain.

We present the design, fabrication, and response of a polymer-based Laterally Amplified Chemo-Mechanical (LACM) humidity sensor based on mechanical leveraging and parametric amplification. The device consists of a sense cantilever asymmetrically patterned with a polymer and flanked by two stationary electrodes on the sides. When exposed to a humidity change, the polymer swells after absorbing the analyte and causes the central cantilever to bend laterally towards one side, causing a change in the measured capacitance. The device features an intrinsic gain due to parametric amplification resulting in an enhanced signal-to-noise ratio (SNR). 11-fold magnification in sensor response was observed via voltage biasing of the side electrodes without the use of conventional electronic amplifiers. The sensor showed a repeatable and recoverable capacitance change of 11% when exposed to a change in relative humidity from 25-85%. The dynamic characterization of the device also revealed a response time ~1s and demonstrated a competitive response with respect to a commercially available reference chip.

As an essential synthetic material used in continuous casting of steels, mold fluxes improve the surface quality of steel slabs. In this study, a CaO-SiO₂-Na₂O based low-fluorine mold flux was solidified by an improved water-cooled copper probe with different temperatures of molten flux and different probe immersion times. The heat flux through solid films and the film structures were calculated and inspected, respectively. The results indicate: large internal cracks (formed in the glassy layer of films during solidification) were observed, the formation and evolution of those cracks contributed to the the unstable heat flux density. The roughness of the surface in contacted with the water-cooled copper probe formed as films were still glassy and the roughness have no causal relationship with crystallization or devitrification. Combeite with columnar and faceted dendritic shapes is the main crystal in the film.

Identifying group movement patterns of crowds and understanding group behaviors is valuable for urban planners, especially when the groups are special such as tourist groups. In this paper, we present a framework to discover tourist groups and investigate the tourist behaviors using mobile phone call detail records (CDRs). Unlike GPS data, CDRs are relatively poor in spatial resolution with low sampling rates, which makes it a big challenge to identify group members from thousands of tourists. Moreover, since touristic trips are not on a regular basis, no historical data of the specific group can be used to reduce the uncertainty of trajectories. To address such challenges, we propose a method called group movement pattern mining based on similarity (GMPMS) to discover tourist groups. To avoid large amounts of trajectory similarity measurements, snapshots of the trajectories are firstly generated to extract candidate groups containing co-occurring tourists. Then, considering that different groups may follow the same itineraries, additional traveling behavioral features are defined to identify the group members. Finally, with Hainan province as an example, we provide a number of interesting insights of travel behaviors of group tours as well as individual tours, which will be helpful for tourism planning and management.

Due to an increase in the number of image achieves, Content-Based Image Retrieval (CBIR) has gained attention for research community of computer vision. The image visual contents are represented in a feature space in the form of numerical values that is considered as a feature vector of image. Images belonging to different classes may contain the common visuals and shapes that can result in the closeness of computed feature space of two different images belonging to separate classes. Due to this reason, feature extraction and image representation is selected with appropriate features as it directly affects the performance of image retrieval system. The commonly used visual features are image spatial layout, color, texture and shape. Image feature space is combined to achieve the discriminating ability that is not possible to achieve when the features are used separately. Due to this reason, in this paper, we aim to explore the low-level feature combination that are based on color and shape features. We selected color moments and color histogram to represent color while shape is represented by using invariant moments. We selected this combination, as these features are reported intuitive, compact and robust for image representation. We evaluated the performance of our proposed research by using the Corel, Coil and Ground Truth (GT) image datasets. We evaluated the proposed low-level feature fusion by calculating the precision, recall and time required for feature extraction. The precision, recall and feature extraction values obtained from the proposed low-level feature fusion outperforms the existing research of CBIR.

Structural vibration induced by dynamic load or natural vibration is a nonnegligible factor in failure analysis. Based on vibrating boundary condition, impact resistance of shape memory alloy reinforced composites is investigated. In this investigation, modified Hashin’s failure criterion, Brinson’s model and visco-hyperelastic model are implemented into the numerical model to charactering the mechanical behavior of glass fiber/epoxy resin laminates, SMAs and interphase, respectively. First, fixed boundary condition is maintained in simulation to verify the accuracy of material parameters and procedures by comparing with experimental data. Then, a series of vibrating boundaries with different frequencies and amplitudes are applied during the simulation process to reveals the effect on impact resistances. The statistics of absorbed energy and contact force indicate that impact resistance of the composite under high frequency and large amplitude is lower than that under low frequency and small amplitude, and summarized by a mathematical expression.

Low Back Pain (LBP) is one of the most common problems among adults. The usual physiotherapy treatment is to perform physical exercises. However, some LBP patients have false beliefs regarding their pain and they tend to avoid physical movements which might increase their pain and disability. Virtual Reality (VR) has shown to be an effective intervention in improving motor functions and reducing pain perception. Existing VR interventions for LBP rehabilitation were based on a non-immersive VR, whereas to effectively reduce the pain intensity, we need an immersive VR. In this paper, we introduce the development and evaluation of a serious game called RabbitRun with an immersive experience to engage the patients in a virtual environment and distract them from the pain while performing LBP exercises. The initial usability evaluation results suggest that RabbitRun game is enjoyable and acceptable. The game is easy to play and learn and most of the participants are willing to play the game at home. This solution will enhance the rehabilitation outcome since the patients who are suffering from LBP can use the system at their home and train more for long period of time using a smartphone and low-cost virtual reality device such as Google Cardboard.

A study of photovoltaic solar window technologies is reported, focusing on their structural features, functional materials, system development, and suitability for use in practical field applications, e.g. public infrastructures and agricultural installations. Energy generation performance characteristics are summarized and compared to theory-limit predictions. Working examples of pilot-trial solar window-based installations are described. We also report on achieving electric power outputs of about 25 W_p/m² from clear and transparent large-area glass-based solar windows.

Starting from the environmental issues related to global warming, climate change and reduction of greenhouse gas emissions, this review paper describes how CO₂ recycling can represent a challenging strategy suitable to explore new concepts and opportunities for catalytic and industrial development. In this view, the production of dimethyl ether (DME) from catalytic hydrogenation of CO₂ appears as a viable technology, able to meet also the ever-increasing need for alternative environmentally-friendly fuels and energy carriers. Basic considerations on thermodynamic aspects controlling DME production from CO₂ are presented, then summarizing the main catalytic systems developed in such a field. Special attention is paid on the role assumed during last years by zeolite-based systems, either in the methanol-to-DME dehydration step or in the one-pot CO₂-to-DME hydrogenation. On the whole, the productivity of DME results significantly to be dependent on several catalyst features, linked not only to the metal-oxide phase responsible for CO₂ activation/hydrogenation, but also to specific properties of the zeolites (i.e., topology, porosity, surface area, acidity, interaction with active metals, distributions of metal particles, …) influencing activity and stability of hybridized bifunctional heterogeneous catalysts.

To improve carbon efficiency for urban logistics service system composed of a third-party logistics service provider (3PLs) and an e-business enterprise, low-carbon operation game between them was studied. Considering low carbon technology investment cost and sales expansion effect of low carbon level, profit functions for both players were constituted. Based on their different bargaining capabilities, totally 5 types of game scenarios were designed. Through analytical solution, Nash Equilibria under varied scenarios were obtained. By analyzing these equilibria, 4 major propositions were given, in which, some key variables and system performance index were compared. Results show that the best system yields could only be achieved under the fully cooperative situation; limited cooperation only for carbon emission reduction would not benefit the system performance improvement; E-business enterprise-leading game’s performance overtook 3PLs-leading ones.

It is well known that the effect of laser irradiation on the blood causes a change in the shape of red blood cells and an increase in their activity, especially in low-level laser therapy (LLLT). The aim of this study was to identify the ability of erythrocytes to deform when exposed to a blue laser.24 laboratory rats were exposed to blue laser in the gingival region of the lower jaw daily for 5 minutes over 3 days. The blue laser possessed a power of 0.5 W and was operated using a con-tactless approach, the dynamic technique in continuous wave mode, and an uninitiated fiber. A blood sample was taken from the lateral vein of the tail before the LLLT, on the first, second, third, and fifth days. The samples were stained, and cytometry was conducted. The exposure to blue laser caused a significant increase in the number of dome-shaped deformable erythrocytes in the blood of laboratory rats (p

Product introductions play a pivotal role in the success and competitiveness of manufacturing, particularly in the context of new product development. Low-volume manufacturing companies exhibit distinct characteristics that significantly influence the product introduction process. Notably, the quality of information exchange between product design and production interfaces becomes paramount in this high-mix and low-volume industry. Consequently, there exists a pressing need to explore various methods for adapting and customizing management mechanisms and strategies to align with the unique requirements and characteristics of low-volume manufacturing and its associated product introduction processes. While the need for this knowledge is critical in the context of low-volume manufacturing, a majority of existing studies predominantly focus on the management aspects within high-volume manufacturing. Therefore, the primary aim of this study is to investigate the customization of product introduction management strategies to enhance the quality of information content within the realm of low-volume manufacturing. Drawing upon a longitudinal analysis of new product introductions within a low-volume manufacturing company, this study narratively elucidates how the examined company implemented product introduction management strategies to facilitate the enhancement of information content quality during the product introduction phase. The study presents its findings on management strategies across three key stages: pre-implementation, post-implementation, and subsequent modification and refinement of strategies following the initial round of implementation. By shedding light on these strategies, this study offers a comprehensive understanding of management approaches in the context of low-volume product introduction. As a result, it makes a valuable contribution to the discourse on information management and interface management in the high-mix, low-volume manufacturing literature.

Growing incidence of myopia worldwide justifies the search for efficient methods of myopia prevention. Numerous pharmacological, optical, and lifestyle measures have already been utilized, but there remains a need to explore more practical and predictable methods for myopia control. This paper presents a review of the latest literature on preventing the progression of myopia using Defocus Incorporated Multiple Segments Spectacle Lenses (DIMSsl), Repeated Low-level Red-Light Therapy (RLRL), and the combination of low-dose atropine (0.01%) with orthokeratology lenses.

The study investigates methods to enhance the reliability of NO2 monitoring using low-cost electrochemical sensors to measure gaseous pollutants in air by addressing the impacts of temperature and relative humidity. The temperature within a plastic container was controlled using an internal mica heater, an external hot air blower or cooling packs, while relative humidity was adjusted using glycerin solutions. Findings indicated that the Auxiliary Electrode (AE) signal is susceptible to temperature and moderately affected by relative humidity. In contrast, the Working Electrode (WE) signal is less affected by temperature and relative humidity; however, adjustments are still required to determine gas concentrations accurately. Tests involving on/off cycles showed that the AE signal experiences exponential decay before stabilizing, requiring the exclusion of initial readings during monitoring activities. Additionally, calibration experiments in zero air allowed the determination of the compensation factor nT across different temperatures and humidity levels. These results highlight the importance of compensating for temperature and humidity effects to improve the accuracy and reliability of NO2 measurements using low-cost electrochemical sensors. This refinement makes the calibration applicable across a broader range of environmental conditions. However, the experiments also show a lack of repeatability of the zero calibration.

Waveform generation as part of an on-chip built-in self-test (BIST) circuitry often necessitates sufficient linearity without expensive hardware overhead. Achieving high linearity is critical for accurate signal generation, especially in applications requiring high precision, such as biomedical and instrumentation. Currently, achieving the high linearity and precision required in signal generators often relies on costly hardware such as automated test equipment (ATE). This paper presents a DAC based hardware synthesizable arbitrary waveform generator. We use a low-cost DAC and a fully digital on-chip testing and calibration approach to nullify the effect of the DAC’s non-linearity on the generated waveform. The ultra-low cost and high linearity benefit of the proposed waveform generator makes it highly suitable for integration into resource-constrained systems. The proposed approach is validated using simulation results of the small-area DAC designed in TSMC 0.18um technology and the testing and calibration algorithms implemented in MATLAB. The DAC, designed with a matching accuracy at only the 5-bit level, is able to generate a signal with an ENOB of 12 bits alongside a SFDR and THD surpassing 100 dB. This high level of signal purity is consistently maintained across 100 Monte-Carlo simulations, demonstrating the robustness of the architecture against PVT variations as well as random mismatches.

Currently, there are few effective methods to monitor patients with gynecologic malignancies, including ovarian and endometrial cancers. The ‘tumor fraction’ of circulating tumor DNA may offer a minimally-invasive method to evaluate tumor aggressiveness via simple blood draw. To date, there is limited data on utility of ctDNA TFx interrogation in gynecologic malignancies, although there is evidence that TFx may be low or undetectable in malignancies primarily confined to the peritoneal cavity. The objective was a descriptive assessment of ctDNA TFx in a cohort of patients with ovarian and endometrial cancer. The association of TFx to continuous and categorical baseline clinicopathologic factors and progression-free survival was assessed. In a large cohort comprised of 210 plasma samples from 78 patients with biopsy-proven ovarian and endometrial cancer, plasma samples collected between 4/2018 and 4/2020 were subjected to shallow whole genome sequencing with determination of TFx. Overall, we demonstrate that TFx was low for most samples with mean TFx for ovarian cancer 5.5% and endometrial cancer 2.4%, yet can be quantified above lower limit of detection in many patients particularly when evaluating serial samples. There was no significant association between TFx level and clinical (primary vs recurrent, best response) or pathologic (e.g. histology, grade) features. Our data demonstrates low TFx levels in ovarian and endometrial cancers likely reflect that tumor types are ‘low ctDNA shed’, suggesting that higher sensitivity assessments may be required for clinical utility.

The effects of toxic air in the form of air pollution are known to harm women’s health. New data has shown that air pollution has effects on maternal anemia. Yet the effects of particulate matter 2.5 (PM_2.5) on hemoglobin among reproductive maternal (15-49 years) has been understudied. In this population-based study, we study the region-specific associations between prevalence of hemoglobin among reproductive women and PM_2.5 in 43 countries of Africa from 2000-2019. Using generalized linear regression models, we found that after adjusting for key covariates, PM_2.5 had a slight negative association with hemoglobin among reproductive women. Other studies are needed in other low-income settings to expand our findings.

Low back pain (LBP) is a significant global health issue, contributing to considerable disability and socioeconomic burdens. The degeneration of the human intervertebral disc (IVD) is a critical factor in the pathogenesis of LBP. Recent studies have emphasized the significance of its specific set of genes and extracellular matrix (ECM) in IVD health. The Noggin gene has emerged as a critical factor due to its high expression levels in healthy nucleus pulposus cells (NPCs) observed in our previous research. In this study, we investigated the hypothesis that decreased Noggin expression in NPCs is associated with IVD degeneration, contributing to LBP development. A lentivirus-mediated RNAi was applied to knockdown Noggin expression in primary NPCs from six human donors. Cell viability analysis, XTT assay, and cell apoptosis were conducted to reveal the effect after transduction. After two weeks, colony formation unit (CFU) assay was used to examine the anchor-independent growth ability of transduced cells. Additionally, qPCR was performed to quantify cellular anabolism and catabolism makers at the transcript level. The results showed lentivirus-mediated downregulation of Noggin suppressed cell growth, cell viability, and colony formation, and induced apoptosis in human NPCs in vitro. Noteworthy, it hindered cellular anabolism and enhanced catabolism activity in human NPCs after transduction. Our findings indicated that the degeneration of human IVD is possibly related to decreased Noggin expression in NPCs. This research provides valuable insights into the role of Noggin in IVD homeostasis and its implications for LBP treatment.

The present study analyses the influence of scratches and fatigue on the mechanical characteristics of aluminium alloys commonly used in the aviation industry: 2024-T4, 6061-T4, 6061-T4 uncoated, 6061-T6 uncoated, 7075-T0, and 7076-T6. 120 specimens were used for the study. Out of these, 60 samples were scratched, and the other 60 samples were also scratched under the same circumstances and then subjected to low-cycle fatigue (LCF) before undergoing the tensile test. Based on the statistical examination of the measured data, mathematical prediction models have been established. Compared to their unscratched counterparts, the results indicate a significant decrease in the mechanical properties of both scratched and scratched-fatigued sample sets. The LCF pre-treatment contributes to the negative impacts of scratches, resulting in a reduced value for the ultimate tensile strength and elongation at break. The results conclude that surface integrity plays an essential role in preserving aircraft components' structural strength.

Obesity is associated with chronic low-grade inflammation. Polyunsaturated fatty ac-ids such as omega-3 (n-3), are essential in the pro-resolution of inflammation. An 8-week double-blind randomized clinical trial was conducted with a n-6:n-3, 5:1 ratio, along with daily 1.8 g of n-3 supplementation vs. placebo. A total of 40 subjects were included, 21 in omega 3 group and 19 in placebo group. The n-3 supplementation had a superior effect compared to placebo increasing levels of Resolvin D1 [129.3 (-90.1 - 193.5) vs. -16.8 (-237.8 - 92.5) pg/mL, p=0.041], IL-10 [1.4 (-0.7 - 4.6) vs. -2.0 (-5 - 0.05) pg/mL, p=0.001], and decreasing IL-6 [-0.67 (2.72 - -0.59) vs. 0.03 (-0.59 - 1.84) pg/mL p=0.015], and MCP-1 [-29.6 (-94.9 - 5.50) vs. 18.3 (-97.3 - 66.35) pg/mL, p=0.040]. In con-clusion, n-3 supplementation promoted resolution of inflammation by increasing sys-temic levels of Resolvin D1, IL-10, and decreasing IL-6 and MCP-1.

In this paper, a low-grade copper oxide ore with highly alkaline was treated. The thermodynamic model of CuO-(NH4)2SO4-NH3-H2O was established in the leaching system of tenorite (CuO) under the condition of double conservation of mass and charge. The fitting function of MATLAB and the diff and solve functions were used to calculate the optimal ammonia concentration and total copper ion concentration of tenorite under different ammonium sulfate concentrations. The effects of different ammonia-ammonium salt (ammonium sulphate, ammonium carbonate, ammonium chloride) solution on copper leaching rate were investigated. Results show that under the conditions of ammonia concentration of 1.2 mol/L, ammonia-ammonium ratio of 2:1 and liquid-solid ratio of 3:1, the copper leaching rate from the ammonium sulphate and ammonium chloride solution reaches 70%, slightly higher than that of ammonium carbonate. Therefore, ammonia ammonium sulfate system is selected to leach low-grade copper oxide due to its lower corrosion to the equipment than the chlorination system.

Background: Physiotherapy and chronic low back pain (CLBP) form a broad and fast developing research area. The aim of the article was to holistically, thematically and chronologically analyze and synthesise literature production and identify most prolific research entities and research themes. Methods: The article quantitatively and quantitatively analyzed research literature production harvested from the Scopus bibliometric database. using a triangulation of bibliometric and thematic analysis. For this, Excell and VOSwiever software were used. Results: In the Scopus database, 2843 data sources were found, which were published between 1974 and February 26, 2024. The growth trend has been linearly positive since the beginning of publication, and after 2018, exponential growth began. A review of the most prolific entities showed that the most literature was published in America, Europe and Australasia. The thematic analysis of the information sources identified six main themes, while the chronological analysis revealed three main areas of developments: assessment tools, CLBP processing and study methodology. Conclusions: The results of the bibliometric study presents a good starting point for further research providing Taxonomy and research landscapes as a holistic framework offering multidisciplinary knowledge about CLBP, while chronological analysis provides a basis for identifying prospective research trends.

The objective of this study is to investigate how different therapies modulating insulin resistance, either causally or consequently, affect metabolic parameters in treatment-naive subjects with T2DM. A total of 212 subjects were assigned to receive either a tight Japanese diet (n=65), pioglitazone at doses ranging from 15-30 mg/day (n=70), or canagliflozin at doses ranging from 50-100 mg/day (n=77) for a duration of three months. Correlations and changes (Δ) in metabolic parameters relative to insulin resistance were investigated. Across these distinct therapeutic interventions, ΔHOMA-R exhibited significant correlations with ΔFBG and ΔHOMA-B, while demonstrating a negative correlation with baseline HOMA-R. However, other parameters such as ΔHbA1c, ΔBMI, ΔTC, ΔTG, Δnon-HDL-C, or ΔUA displayed varying patterns depending on the treatment regimens. Participants were stratified into two groups based on the median value of ΔHOMA-R: the lower half (X) and upper half (Y). Group X consistently demonstrated more pronounced reductions in FBG compared to Group Y across all treatments, while other parameters including HbA1c, HOMA-B, TC, TG, HDL-C, non-HDL-C, TG/HDL-C ratio, or UA exhibited distinct regulatory responses depending on the treatment administered These findings suggest that 1) regression to the mean is observed in the changes of insulin resistance across these therapies. 2) modulation of insulin resistance with these therapies, either causally or consequentially, results in differential effects on glycemic parameters, beta-cell function, specific lipids, body weight or UA.

The use of chemical pesticides in agriculture contributes to soil, water and air pollution, biodiversity loss and can harm non-target species. The European Commission has already established a Harmonized Risk Indicator to quantify the progress in reducing the risks linked to pesticides. Therefore, there is an increasing need to promote biopesticides or so-called low-risk pesticides (LRP). Extract from Melaleuca alternifolia – tea tree oil (TTO) is known for its antiseptic, antimicrobial, antiviral, antifungal, and anti-inflammatory properties. Tea tree oil has been extensively studied in pest management as well as in the pharmaceutical and cosmetic industry and there are already products based on its active substances on the market. This review focuses on the overall evaluation of tea tree oil in terms of effectiveness and safety as a biopesticide for the first time. The collected data can be an added value for further evaluation of tea tree oil in terms of the authorization extension as a fungicide in 2026.

Ovarian cancer (OC) is an umbrella term for cancerous malignancies affecting the ovaries, yet treatment options for all subtypes are predominantly derived from high-grade serous ovarian cancer, the largest subgroup. The concept of "functional precision medicine" involves gaining personalized insights on therapy choice, based on direct exposure of patient tissues to drugs. This especially holds promise for rare subtypes like low-grade serous ovarian cancer (LGSOC). This study aims to establish an in vivo model for LGSOC using zebrafish embryos, comparing treatment responses previously observed in mouse PDX models, cell lines, and 3D tumor models. To address this goal, a well characterized patient-derived LGSOC cell line with the KRAS mutation c.35 G > T (p.(Gly12Val)) was used. Fluorescently labelled tumor cells were injected into the perivitelline space of 2 days post fertilization zebrafish embryos. At 1 day post-injection xenografts were as-sessed for tumor size, followed by random allocation into treatment groups with trametinib, luminespib, and trametinib + luminespib. Subsequently xenografts were euthanized and analysed for apoptosis and proliferation by confocal microscopy. Tumor cells formed compact tumor masses (n=84) in vivo and with clear Ki67 staining, indicating proliferation. Zebrafish xenografts exhibited sensitivity to trametinib and luminespib, individually or combined, within a two-week period, establishing them as a rapid and complementary tool to existing in vitro and in vivo models for evaluating targeted therapies in LGSOC.

To reduce the redundant counting of TDC in high-speed applications and thus reduce power consumption, a TDC architecture is proposed to quantify the difference between two adjacent rows of pixel signals. This structure can remove the identical part between two rows of pixel signals by adjusting the start and stop signal of the TDC, which will reduce the number of flipping of D flip-flops in the TDC. In the 110nm CMOS process, simulation results show that this design achieves an effective number of bits (ENOB) of 4.72 bits and a Figure of Merit (FoM) of 104.7 fJ/step - 162.3 fJ/step with a power consumption ranging from 60 µW to 93 µW. Compared with traditional counting methods, the proposed TDC can reduce counting power consumption by 30%.

This paper provides a comparative analysis of AES (Advanced Encryption Standard) and Salsa20 algorithm implementations, focusing on power consumption efficiency in passive RFID (Radio Frequency Identification) tags and ultra-low-power devices. The main objective of this work is to determine which of these algorithms is more suitable to operate in these types of devices. For this purpose, ASIC (Application-Specific Integrated Circuit) implementations of AES and Salsa20 based on low-power approaches were developed and their power consumption was evaluated. Results demonstrate that Salsa20 power consumption is lower than AES (2.82μW and 4.01μW, respectively - both in 0.18μm), indicating that Salsa20 is a better choice than AES for passive RFID tags.

C-peptide is used as a measure of endogenous insulin production. Given that insulin and C-peptide are produced in equal amounts, C-peptide is typically used to differentiate between external and endogenously produced insulin in insulin-treated type 1 diabetes mellitus (T1DM). In a clinical setting, a decline in C-peptide is regarded as a loss of beta cell function. However, physiological conditions may also be associated with low C-peptide levels. The authors of this paper use a low-carbohydrate diet, the so-called paleolithic ketogenic diet (PKD), in the treatment of various conditions and observed that C-peptide is typically low on this diet. In order to characterize C-peptide levels on this diet, we designed a study to retrospectively assess C-peptide levels in 100 non-T1DM subjects. We found that 55% of the subjects had a C-peptide level below the standard reference range. C-peptide levels correlated with glucose levels. A significant correlation was found between C-peptide and age, with younger subjects having lower C-peptide levels. Males also showed lower C-peptide levels than females. Given the increasing number of patients using low-carbohydrate diets worldwide, physicians should be aware of laboratory correlates of low-carbohydrate diets, including low C-peptide levels, most importantly to prevent incorrect T1DM diagnosis.

A millimeter-wave microstrip leaky-wave antenna array based on the substrate-integrated waveguide (SIW) and the complementary split-ring resonator (CSRR) is proposed in this paper. The slow wave characteristics of the SIW are enhanced by etching two rows of symmetrical CSRR-type slots on the surface of the SIW layer. The magnetic coupling between the CSRR-SIW layer and equally spaced circular patches array on the upper layer realizes the radiation of electromagnetic energy. In the 23~30 GHz (relative bandwidth 26.4%) operating frequency band, the horizontal polarization radiation beam scanning from -62° to -2° is realized, with a peak gain of 9.6~11.7 dBi, and the cross-polarization ratio is more than 43.8 dB.

Background: Hemangiomas are an aberrant proliferation of blood vessels and are the most frequent benign pediatric soft tissue tumors. Despite their being common, genital localisation is rare. This study aimed to assist doctors in the diagnosis, management, and treatment of paediatric vulvovaginal hemangiomas by conducting a review of the literature and also gathering some cases of patients from our clinic.Methods: We conducted a literature review including papers published between October 2021 and April 2023, and we described the cases of 3 patients who referred to our clinic with vulvovaginal hemangioma.Results: While most of hemangiomas are usually indolent and resolve with time, in some cases, especially vaginal and cervical ones, they might present with severe symptoms like heavy bleeding and need further instrumental investigation for diagnosis, like CT or MRI. As for the treatment many options are available with medical therapy or expectant management being the first choice.Conclusions: Vulvovaginal pediatric hemangiomas are rare and, so, more research should be done to how to detect and manage this lesions, especially the symptomatic and the psychologically impacting ones. For the time being treatment should personalized based also on the patient situation and clinician’s expertise.

Water scarcity challenges have necessitated the adoption of water-saving techniques in protected and nom-protected farming. This study aimed to assess the performance of a water-saving soil-less cultivation technique and to compare it with conventional soil-based cultivation in protected farming. The soilless technique used local gravel and a mixture of peat-moss, humin-substrate, and perlite in ratios of 4:3:1.5. Three irrigation regimes were imposed using emitters 8Lh-1 design discharge (D1) emitters with 6Lh-1 design discharge (D0.75) and 4Lh-1 de-sign discharge (D0.5) for the two cultivation methods during the growth cycle of tomato by drip irrigation. The vegetative growth, fruit yield and water consumption were measured and water productivity was determined. Moreover, an economic assessment was carried out by estimating and comparing economic coefficients for the two cultivation methods. Estimated coefficients include revenues, net profit, benefit-cost ratio, break-even levels of production and prices, revenues over variable cost, and revenues on investment. The tomato fruit yield under soil-based cultivation overtopped the yield under soilless cultivation. The water productivity under the soilless cultivation was almost twice that (24.3 kg m-3) of the soil-based cultivation (15.5 kg m-3). The soilless cultivation saved 50% of irrigation water applied by the conventional soil-based method, saving energy and soil from deterioration. Revenues and net profits stimulated by higher yield coupled with lower variable cos supported the soil-based cultivation. The economic assessment showed that both cultivation methods were economically viable. However, the soil-based cultivation method was more profitable due to its higher fruit yield. Overall, the results of this study suggest that the soilless cultivation technique is a viable option for wa-ter-saving cultivation. However, the soil-based cultivation method is still more profitable due to its higher fruit yield

Objective: To observe the effect of the combination of fluid-increasing decoction, low molecular heparin sodium and aspirin in the treatment of oligohydramnios in pregnancy. Methods: In this study, 114 pregnant women with oligohydramnios during pregnancy admitted to our hospital between May 2019 and March 2022 were selected as objects, and the pregnant women were equally divided into the observation group and the experimental group by random number table method, with 57 cases in each group. The observation group received conventional fluid infusion, low molecular heparin sodium and aspirin, while the experimental group was treated with fluid-increasing decoction on the basis of the observation group. The treatment effect, S/D level, amniotic fluid index, maximum vertical pocket (MVP), coagulation indexes (plasma prothrombin time (PT), plasma activated partial thromboplastin time (APTT), fibrinogen (FIB)), pregnancy outcome and adverse reactions were compared between the two groups. Results: The total effective rate of treatment was obviously better in the experimental group than that in the observation group (P＜0.05); the S/D level after treatment in the experimental group was remarkably lower than that in the observation group (P＜0.05). The amniotic fluid index and MVP were remarkably higher in the experimental group than in the observation group after treatment (P < 0.05). No significant differences in PT, APTT and FIB were found between the two groups before and after treatment (P > 0.05). The rate of oligohydramnios at delivery, cesarean section rate, neonatal weight status and preterm delivery rate were dramatically better in the experimental group than in the observation group (P < 0.05). Post-partum haemorrhage rate, neonatal asphyxia rate, amniotic fluid contamination rate and incidence of adverse events were not significantly different between the two groups of pregnant women (P > 0.05). Conclusion: The combination of fluid-increasing decoction, low molecular heparin sodium and aspirin is clinically effective and safe in the treatment of pregnant women with oligohydramnios during pregnancy. The combination is effective in reducing the S/D ratio of fetal umbilical blood flow, enhancing the amniotic fluid index and MVP in pregnant women with oligohydramnios during pregnancy, whilst not adversely influencing the coagulation function of the mother, thus contributing to a reduction in the risk of adverse pregnancy outcomes.

Controlling injection parameters is paramount when it comes to producing high-quality green parts using powder injection molding. This work combines experimental and numerical approaches to study the impact of injection parameters on mold in-cavity pressure and on the overall quality of green parts produced by low-pressure powder injection molding. The properties of two low-viscosity feedstocks (formulated from a water-atomized stainless-steel powder and wax-based binder system) were measured and implemented in an Autodesk Moldflow numerical model to quantify the molding pressures, which were finally validated using experimental real-scale injections. The results confirmed that an increase in mold temperature, an increase in feedstock temperature, and a decrease in solid loading decrease the mold in-cavity pressure, which was correlated with the feedstock viscosity. As a key result, real-scale injections confirmed that a minimum flow rate was required to avoid atypical high in-cavity pressure leading in several visual defects such as weld lines, flow marks, cracks, sinks, and incomplete filling. Due to differences in its thermal transfer properties, this flow rate threshold value decreases as the feedstock solid loading increases. For injection speeds higher than this value, the injection pressure measured experimentally was linearly correlated with the injection flow rate.

Pharmaceutical poisoning is a significant global public health concern, causing approximately 190,000 deaths yearly. This scoping review aims to comprehensively map the available literature on pharmaceutical poisoning and compare patterns between high-income countries (HICs) and low-middle-income countries (LMICs). A systematic search was performed across the following databases: Embase, PubMed, Cochrane Database of Systematic Reviews, Cochrane Central Register of Controlled Trials, and CINAHL. Studies included were from 1st January 2011 to 31st December 2020, in English, with full text available. Seventy-nine articles were included in the study; 21 were from LMICs and 58 were from HICs. The toxic exposure was largely intentional (77%) in LMICs and accidental (68%) in HICs. Drugs acting on the nervous system were responsible for 95% of toxicities worldwide with analgesics accounting for the largest subtherapeutic group in both LMICs (40%) and HICs (58%). Notable statistics were that HICs accounted for 99% of opioid overdoses, and LMICs accounted for 19% of anti-epileptic-induced toxicities. Overall, the medical outcomes of poisonings were generally worse in LMICs. The review provides possible interventions to target specific geographic locations, based on the trends identified, to reduce the burden worldwide. Many gaps within the literature were recognised, calling for more robust analytical research.

This research aims to develop an inexpensive ocean observation instrument with a project name is NOBEL (Nusantara Oceanography Backdoor Experiment Laboratory)-BOX. The device can be installed on all types of vessels and placed in a specific area to map the water conditions, providing accurate data for managing a marine area specifically to water quality. The principle of NOBEL-BOX is to attach sensors in a container connected to a microcontroller and then measure directly. The method employed includes experimental design, laboratory and field tests, and data evaluation to produce the necessary system and instruments. The design process involves the construction of the instrument and the fabrication of the device. This process includes creating three-dimensional sketches/drawings, designing microcontrollers and data transmission systems, and power capacity. The sensors attached to this device are surface water temperature, air temperature, salinity, dissolved oxygen, pH, and TDS. The testing phase includes data validation, testing of the device in the laboratory, and field testing. The laboratory and field tests showed that the device worked and provided data that can be used to analyze the seawater condition spatially and over time.

This paper introduces an advanced method that integrates contingent valuation and machine learning (CVML) to estimate residents’ demand for reducing or mitigating environmental pollutions and climate change. To be precise, CVML is an innovative hybrid machine-learning model, and it can leverage a limited amount of survey data for prediction and data enrichment purposes. The model comprises of two interconnected modules: Module I, an unsupervised learning algorithm, and Module II, a supervised learning algorithm. Module I is responsible for grouping the data into groups based on common characteristics, thereby grouping the corresponding dependent variable, whereas Module II is in charge of demonstrating the ability to predict and the capacity to appropriately assign new samples to their respective category based on input attributes. Take a survey on the topic of air pollution in Hanoi in 2019 as an example, we found that CVML can predict households’ willingness– to– pay for polluted air mitigation at a high degree of accuracy (i.e., 98%). We found that CVML can help users reduce costs or save resources because it makes use of secondary data that is available on many open data sources. These findings suggest that CVML is a sound and practical method that could be widely applied in a wide range of fields, particularly environmental economics and sustainability science. In practice, CVML could be used to support decision-makers in improving the financial resources to maintain and/or further support many environmental programs in years to come.

Mercury emissions from small-scale coal-fired boilers are still a serious environmental problem in Poland and the Czech Republic. The publication presents the results of mercury emission tests conducted using five different small-scale coal-fired boilers and five different coal fuels. The research was carried out under laboratory conditions, but also using residential users' heating devices. They covered a wide range of operational parameters, both energy and emission. It was shown that more than 94% of the mercury contained in coal fuel undergoing combustion is emitted into the atmosphere with the volatile products of combustion (including dust), and the amount of emissions is strongly dependent on the original mercury content of the fuel. One solution to the problem of mercury emissions from small-scale coal-fired boilers may be to replace traditional coal with low-emission carbon fuels. The paper shows that mercury emissions from burning such fuels are many times lower than from burning coal. The widespread use of low-emission carbon fuels in individual heating systems in Poland and the Czech Republic would reduce mercury emissions to the atmosphere by up to 90% compared to the current level of emissions generated by individual heating systems in these countries.

Developing a low-cost wireless energy meter with power quality measurement for smart grid applications represents a significant advancement in efficient and accurate electrical energy monitoring.In increasingly complex and interconnected electrical systems, this device is essential in various applications, such as smart grids, enabling real-time energy usage monitoring. In such a context, smart meters expand the possibilities for sustainable and efficient energy use and promote better utilization of energy sources, especially non-renewable ones. According to the 2020 International Energy Agency (IEA) research, non-renewable energy sources represent 65% of the global total. The smart meter developed in this work is built based on the ESP32 microcontroller and easily accessible components, using a user-friendly development platform that offers a cost-effective solution while ensuring reliable performance. The main objective of the smart meter development was to enhance the software and simplify the hardware. Unlike traditional meters that perform electrical parameter calculations using complex hardware circuits, this project performed the calculations directly on the microcontroller. This approach reduced the complexity of the hardware, simplifying the meter’s design. With the high-performance processing capability of the microcontroller, efficient and accurate calculations of electrical parameters were achieved without the need for additional circuits. This software-driven approach with simplified hardware brought benefits such as reduced production costs, lower energy consumption, and increased meter development and updates flexibility. Furthermore, the integrated wireless connectivity in the microcontroller enables the transmission of collected data to remote monitoring systems for later analysis. The developed smart meter offers cost, energy efficiency, and flexibility benefits. It represents an innovative, efficient, and versatile solution for smart grid applications.

A high perovskite activity is sought for use in magnetic applications. In this paper, we present the simple synthesis of (2.5 and 5%) Tellurium-impregnated-LaCoO3 (Te-LCO), Te and LaCoO3 (LCO) by using a ball mill, chemical reduction, and hydrothermal synthesis, respectively. We also explored the structure stability along with the magnetic properties of Te-LCO. Te has a rhombohedral crystal structure, whereas Te-LCO has a hexagonal crystal system. The reconstructed Te was imbued with LCO that was produced by hydrothermal synthesis; as the concentration of the imbuing agent grew, the material became magnetically preferred. According to the X-ray photoelectron spectra, the oxidation state of the cobaltite is one that is magnetically advantageous. As a result of the fact that the creation of oxygen-deficient perovskites has been shown to influence the mixed (Te4+/2-) valence state of the incorporated samples, it is abundantly obvious that this process is of utmost significance. The TEM image confirms the inclusion of Te in LCO. The samples start out in a paramagnetic state (LCO), but when Te is added to the mixture, the magnetic state shifts to a weak ferromagnetic one. It is at this point that hysteresis occurs due to the presence of Te. Despite being doped with Mn in our prior study, rhombohedral LCO retains its paramagnetic characteristic at room temperature (RT). As a result, the purpose of this study was to determine the impacts of RT field dependency of magnetization (M-H) for Te-impregnated LCO in order to improve the magnetic properties of RT because it is a low-cost material for advanced multi-functional and energy applications.

Low-temperature accumulation is one of the essential stages in the growth process of woody ornamental plants. In this study, two different low-temperature treatments, 6℃ and 10℃, were used to analyze the effects of different low-temperature treatments on dormancy release and flowering of the 'Gulihong' plant using artificial low temperatures. Based on the experimental results, four typical early-blooming Prunus mume cultivars widely planted in Yangling area of Henan Province, China, including 'Zaoyudie', 'Zaohualve', 'Nanjing gongfen', and 'Gulihong', were selected as the experimental materials. The effects of low-temperature accumulation on the flowering characteristics of different cultivars were analyzed using a 6℃ artificial low-temperature treatment. The suitable cultivation temperature for early-blooming P. mume cultivars was screened to provide a theoretical basis for further exploration of P. mume bonsai cultivation techniques. The results showed that the flowering rate, flower diameter, flowering quantity, flowering uniformity, and bud development in the 6℃ treatment were significantly better than those in the 10℃ treatment. The flowering rate and quality of different cultivars gradually increased with the accumulation of low-temperature. Therefore, chill accumulation plays a significant role in promoting flowering quality.

Background: Low-level (LLLT) and high-intensity laser therapy (HILT) can be beneficial additions to knee osteoarthritis (KOA) rehabilitation exercises; however, it is still being determined which modality is more effective. Aim: To compare the effects of LLLT and HILT as adjuncts to rehabilitation exercise (LL+EX and HL+EX) on clinical outcomes in KOA. Methods: Thirty-four adults with mild to moderate KOA were randomly allocated to either LL+EX (n = 17) or HL+EX (n = 17) groups. All participants underwent their designated laser treatment combined with rehabilitation exercises weekly for twelve consecutive weeks. The Knee Injury and Osteoarthritis Outcome Score (KOOS), Numerical Pain Rating Scale (NPRS), active knee flexion, and Timed Up-and-Go test (TUG) were assessed at baseline and immediately post-intervention. Results: Post-intervention, both groups significantly improved their KOOS, NPRS, active knee flexion, and TUG scores compared to baseline (p &lt; 0.01). The mean difference of change in KOOS, NPRS, and active knee flexion scores for the HL+EX group surpassed the minimal clinically important difference threshold. In contrast, the LL+EX group only demonstrated clinical significance in NPRS scores. Conclusions: Incorporating HILT as an adjunct to usual KOA rehabilitation led to significantly higher improvements in pain, physical function, and knee-related disability compared to LLLT.

Hillslope and mountain roads are often the source of erosion, which in turn can lead to larger landslides and other types of mass-movements. For this reason, low-cost repeat surveys that can be done by practitioners and not solely scientists and engineers is essential. To solve this issue the present contribution shows the testing and applicability of a mix of SfM-MVS and low-cost SLAM technology to provide erosion information. The low-cost SLAM generated between 300 ~ 900 points per square meter, while SfM-MVS created between ~11,000 to 900,000 points. The density is however a trade-off against a spatially varying error, although the variability at the road-cut scale only ranges from 2 cm vertically to 2.5 cm in x,y,z based on the C2C algorithm. Furthermore, this error tends to be more important in the higher section of the cutout (further away from the sensor and at a flatter angle). It is thus possible to measure small-scale roadside change, providing that the change is in the range of >5 cm (adding the maximum potential error twice) and providing that the road-cut is such that the sensors can be brought close to the surface (camera or sensor on a pole). The authors suggest that it can be a solution for state and agencies with limited funding and that cannot afford regular laser or for roadside that are difficult to access.

Small rodents and insectivores are potential reservoirs of many pathogens transmissible to humans such as bacteria, parasites and viruses responsible for epidemics in sub-Saharan Africa, particularly in West Africa. Few studies on small mammal species in the Kolikoro and Sikasso regions are available, hence the interest in investigating the different species of small rodents and insectivores, and their role in the transmission of pathogens to humans. The study aims to identify commensal small mammal species circulating in Faladjè and Bougouni areas, and likely to represent major risks of epidemic disease emergence. Sessions of trapping were carried out in December 2016 in Faladjè and Bougouni with wire mesh traps type “Besançon tous services” (BTS) baited with peanut butter and/or onion. All animals captured were identified morphologically. Out of 123 small rodents and insectivores captured in 674 trap nights, 75 (60.97%) were from Faladjè and 48 (39.02%) from Bougouni, Of these, six species of small rodents belong to the family Muridae (Mastomys erythroleucus, Mastomys natalensis, Rattus rattus, Praomys daltoni, Gerbilliscus gambianus, Taterillus gracilis) and two species of insectivores associated with the genus Crocidura spp. belong to the family Soricidae and Erinaceidae (Crocidura cf olivieri and Atelerix cf albiventris) respectively. There is low specific diversity within these two stands, but the variation in relative abundance is significant (binomial test, p = 0.018 ˂ 0.05) between the Faladjè and Bougouni stands of small mammals. Mastomys erythroleucus was the most dominant species (57.33%, 43/75) in the Faladjè settlement and R. rattus dominated (37.5%,18/48) that of Bougouni. These two species of small mammals are potentially involved in the transmission of bacteria, parasites and pathogenic viruses to humans.

This paper addresses the difficulty of balancing real-time response and low power consumption in intelligent manhole cover application scenarios. It proposes a method to distinguish normal and abnormal events by segmenting the boundary where the acceleration of the intelligent manhole cover deviates from a set threshold and lasts for a certain period, based on the difference in vibration patterns of the intelligent manhole cover when a normal event and an abnormal event occur. This paper uses digital output motion sensor data autonomous data fusion to implement the pattern mentioned above recognition algorithm, which reduces the MCU computing and working time and the overall power consumption of the system while meeting the real-time response requirements. The test results demonstrate that the method has a high rate of anomaly recognition accuracy. The method ensures the system's real-time response capability, and the actual low power consumption test demonstrates that the device can operate continuously for 9.5 years. The low power consumption index exceeds the requirements of the existing national standard, thereby resolving the issue that it is challenging to balance intelligent manhole cover abnormality recognition and low power consumption.

Chronic pain is a source of major alterations in quality of life. It represents significant costs for health systems, and reduces the competitiveness of the working population. Vulnerability can drive the incidence of chronic pain, through its influence on modifiable risk factors, and reduced utilization of health care systems. But vulnerability can also be the consequence of a chronic pain: illness can push people into precariousness. We analysed the factors associated with pain intensity among vulnerable persons with a chronic condition, in five European countries (N=1,364). Pain was, among the whole set of variables, the main predictor of sleep problems, fatigue, depression, self-perceived health, physical and mental quality of life. This is in line with other studies showing the major impact of pain on an individual’s health and life. Multivariable analyses, adjusting for the whole set of variables, showed that women had more intense pain, as well as participants with a lower education level. These results confirm the social component in the complex etiology of pain and clearly plaid in favor of integrated care, taking into account individual characteristics and environment.

Lithium-ion batteries (LIBs) have become the preferred battery system for portable electronic devices and transportation equipment because of their high specific energy, good cycling performance, low self-discharge and no memory effect. However, too low ambient temperature will seriously affect the performance of LIBs, almost cannot discharge at -40~-60 ℃. There are many factors affecting the low temperature performance of LIBs, among which the electrode material is an important factor. Thus it is urgent to develop electrode materials or modify existing materials with excellent low temperature LIBs performance. Carbon-based anode is a kind of LIBs candidate. In recent years, it has been found that the diffusion coefficient of lithium ion in graphite anode decreases more obviously at low temperature, which is one of the important bottlenecks limiting its low temperature performance. However, the structure of amorphous carbon materials is complex, amorphous carbon materials have good ionic diffusion properties, and its grain size, specific surface area, layer spacing, structural defects, surface functional groups and doping elements may have a greater impact on the low temperature performance of the material. In this work, the low temperature performance of LIBs is obtained by modifying the carbon-based material from the perspective of electronic modulation and structural engineering.

When bone substitutes materials are used, the increased risk of infection due to the none-autogenic graft is often discussed. The treatment of large bone defects in geriatric patients, often with osteoporotic bone, often presents major challenges to surgery. Bone substitutes materials are available indefinitely without the risk of additional surgery in each patient. Can bone substitutes materials be used without hesitation in the geriatric patient?Eighty-three patients suffered traumatic fractures of the distal radius, proximal humerus, and proximal tibia. The defect zones were filled with bone substitute material based on nanocrystalline hydroxyapatite (NHA) or calcium phosphate (CP). For comparison, a reference group without the void filling with a bone graft substitute (void defects, ED) was studied. All patients over the age of 64 years were retrospectively evaluated for complications and radiological outcomes. Results: 106 patients sustained traumatic fractures of the distal radius (68.9%), proximal humerus (5.7%), and proximal tibia (22.6%). No differences in infections were found when comparing the groups (p=1.0). retrospectively evaluated. The KEM group had a nonsignificantly lower rate of pseudarthrosis (p=0.09). A relative risk (RR) reduction of complications of 32.64% was observed when bone grafting material was used. The NNT for the prevention of complications was 5.99. When bone healing was assessed by radiological images, some follow-up studies showed significant differences in fracture bridging (p<0.001).Conclusions: In contrast to previous studies, bone substitutes materials can support the healing process in geriatric patients without relevant disadvantages. With an NNT of 6 regarding complications, many patients could benefit from bone graft augmentation. No increased infection rate was observed.

When bone substitutes materials are used, the increased risk of infection due to the none-autogenic graft is often discussed. The treatment of large bone defects in geriatric patients, often with osteoporotic bone, often presents major challenges to surgery. Bone substitutes materials are available indefinitely without the risk of additional surgery in each patient. Can bone substitutes materials be used without hesitation in the geriatric patient? Eighty-three patients suffered traumatic fractures of the distal radius, proximal humerus, and proximal tibia. The defect zones were filled with bone substitute material based on nanocrystalline hydroxyapatite (NHA) or calcium phosphate (CP). For comparison, a reference group without the void filling with a bone graft substitute (void defects, ED) was studied. All patients over the age of 64 years were retrospectively evaluated for complications and radiological outcomes. Results: 106 patients sustained traumatic fractures of the distal radius (68.9%), proximal humerus (5.7%), and proximal tibia (22.6%). No differences in infections were found when comparing the groups (p=1.0). retrospectively evaluated. The KEM group had a nonsignificantly lower rate of pseudarthrosis (p=0.09). A relative risk (RR) reduction of complications of 32.64% was observed when bone grafting material was used. The NNT for the prevention of complications was 5.99. When bone healing was assessed by radiological images, some follow-up studies showed significant differences in fracture bridging (p<0.001). Conclusions: In contrast to previous studies, bone substitutes materials can support the healing process in geriatric patients without relevant disadvantages. With an NNT of 6 regarding complications, many patients could benefit from bone graft augmentation. No increased infection rate was observed.

The main aspects of material research: material synthesis, material structure, and material properties, are interrelated. Acquiring atomic structure information of electron beam sensitive materials by electron microscope, such as porous zeolites, organic-inorganic hybrid perovskites, metal-organic frameworks, is an important and challenging task. The difficulties in characterization of the structures will inevitably limit the optimization of their synthesis methods and further improve their performance. The emergence of integrated differential phase contrast scanning transmission electron microscopy (iDPC-STEM), a STEM characterization technique capable of obtaining images with high signal-to-noise ratio under lower doses, has made great breakthroughs in the atomic structure characterization of these materials. This article reviews the developments and applications of iDPC-STEM in electron beam sensitive materials, and provides an outlook on its capabilities and development.

The electronic structural evolution of LLM-105 crystal and the (101) plane of LLM-105 crystal under different pressures is investigated by the density functional theory (DFT) calculations and the surface properties of seven low-Miller-index planes of LLM-105 crystal were investigated in this study. The result demonstrates that the surface energy of (101) plane of LLM-105 is much smaller when compared with other low-Miller-index planes of LLM-105.In order to further investigate the stability of crystal structure and (101) plane of LLM-105 under different pressures, a series of pressures ranged from 0 GPa to 55 GPa were applied during the DFT calculation, and the result shows that the electronic structures of LLM-105 crystal and the (101) plane changed with the increase of external pressure and the evolution process of (101) plane is different from that of LLM-105 crystal structure.

The copper end paste used in multilayer ceramic capacitors sintered in nitrogen atmosphere will lead to carbon residue of organic vehicle, which will lead to the reduction of electrode conduc-tivity and high scrap rate. With an attempt to leave no residue in the sintering, the compatibility of solvents and thickeners should be improved because it has an important influence on the hi-erarchical volatilization and carbon residue of organic vehicles. In this work, the volatility of different solvents was compared and several solvents were mixed in a definite proportion to prepare an organic vehicle with polyacrylate resins. The hierarchical volatility and solubility parameters of mixed solvents were adjusted effectively by changing proportions of different components, the thermogravimetric curves of resins and organic vehicles were measured by thermogravimetric analyzer, the effect of solubility parameter on the dissolvability of resins in the solvent and the residual of organic vehicles were studied. Results showed that the hierar-chical volatilization of solvents can be obtained by mixing different solvents; the intrinsic vis-cosity of the organic vehicle is higher and the thermal decomposition residue of polyacrylate resins is lower when the solubility parameters of mixed solvents and polyacrylate resins are closer. The low residual sintering of organic vehicles can be achieved by using the mixed solvent with hierarchical volatility and approximate solubility parameters as resins.

Existing methods enhance mid-low resolution remote sensing ship detection by feeding super-resolved images to the detectors. Although these methods marginally improve the detection accuracy, the correlation between image super-resolution (SR) and ship detection is under-exploited. In this paper, we propose a simple but effective ship detection method called ShipSR-Det, in which both the output image and the intermediate features of the SR module are fed to the detection module. Using the super-resolved feature representation, the potential benefit introduced by image SR can be fully used for ship detection. We apply our method to the SSD and Faster-RCNN detectors and develop ShipSR-SSD and ShipSR-Faster-RCNN, respectively. Extensive ablation studies validate the effectiveness and generality of our method. Moreover, we compare ShipSR-Faster-RCNN with several state-of-the-art ship detection methods. Comparative results on the HRSC2016, DOTA and NWPU VHR-10 datasets demonstrate the superior performance of our proposed method.

Existing Reynolds Averaged Navier-Stokes based transition models do not accurately predict separation induced transition for low pressure turbines. Therefore, in this study, a novel framework based on computational fluids dynamics driven machine learning coupled with multi-expression and multi-objective optimization is explored to develop models which can improve the transition prediction for the T106A low pressure turbine at an isentropic exit Reynolds number of Re2is=100,000. Model formulations are proposed for the transfer and laminar eddy viscosity terms of the laminar kinetic energy transition model using seven non-dimensional pi groups. The multi-objective optimization approach makes use of cost functions based on the suction-side wall-shear stress and the pressure coefficient. A family of solutions is thus developed, whose performance is assessed using Pareto analysis and in terms of physical characteristics of separated-flow transition. Two models are found which bring the wall-shear stress profile in the separated region at least two times closer to the reference high-fidelity data than the baseline transition model. As these models are able to accurately predict the flow coming off the blade trailing edge, they are also able to significantly enhance the wake-mixing prediction over the baseline model.

In this letter, we show an alternative low-cost fabrication method to obtain poly(dimethyl siloxane) (PDMS) microfluidic devices. The proposed method allows the inscription of micron resolution channels on polystyrene (PS) surfaces, used as a mold for the wanted microchip’s production, by applying a high absorption coating film on the PS surface to ablate it with a focused low-power visible laser. The method allows obtaining micro resolution channels at powers between 2 and 10mW and can realize any two-dimensional polymeric devices. The effect of the main processing parameters on the channel’s geometry is presented.

There is accumulating evidence that prenatal exposure to air pollution disturbs fetal growth and development, but little is known about these effects in cold climates or their season-specific or joint effects. Our objective was to assess independent and joint effects of prenatal exposure to specific air pollutants on the risk of low birth weight (LBW). We utilized the 2568 children of the Espoo Cohort Study, born between 1984 and 1990, and living in the City of Espoo. We conducted stratified analyses for births during warm and cold seasons separately. We analyzed the effect estimates using multi-pollutant Poisson regression models with risk ratio (RR) as the measure of effect. The risk of LBW was related to exposure to CO and (adjusted RR 1.44, 95% CI: 1.04-2.00) and exposure to O3 in the spring-summer season (1.82, 1.11-2.96). There was also evidence of synergistic effects between CO and O3 (relative risk due to interaction, RERI, all year 1.08, 95% CI: 0.27-4.94, spring-summer 3.97, 2.17-25.85) and PM2.5 and O3 (all year 0.72, -0.07-3.60, spring-summer 2.80, 1.36-19.88). We present new evidence of both independent and joint effects of prenatal exposure in a cold climate on the risk of LBW at low levels of air pollution.

Central nervous system (CNS) uses vision, vestibular, and somatosensory information to maintain body stability. Research has shown that there is more lumbar proprioception error among low back pain (LBP) individuals as compared to healthy people. In this study, two groups of 20 healthy people and 20 non-specific low back pain participants (LBP) took part in this investigation. This investigation focused on somatosensory sensors and in order to alter proprioception, a vibrator (frequency of 70Hz, amplitude of 0.5 mm) was placed on the soleus muscle area of each leg and two vibrators were placed bilaterally across the lower back muscles. Individuals, whose vision was occluded, were placed on two surfaces (foam and rigid) on force plate, and trunk angles were recorded simultaneously. Tests were performed in 8 separate trials; the independent variables were vibration (4 levels) and surface (2 levels) for within subjects and 2 groups (healthy and LBP) for between subjects (4×2×2). MANOVA and multi-factor ANOVA tests were done. Linear parameters for center of pressure (COP) (deviation of amplitude, deviation of velocity, phase plane portrait (PPP), and overall mean velocity) and nonlinear parameters for COP and trunk angle ((recurrence quantification analysis) RQA and Lyapunov exponents) were chosen as dependent variables. Results indicated that NSLBP individuals relied more on ankle proprioception for postural stability. Similarly, RQA parameters for the COP on both sides and for the trunk sagittal angle indicated more repeated patterns of movement among the LBP cohort. Analysis of short and long Lyapunov exponents showed that people with LBP caused no use of all joints in their bodies (non-flexible), are less stable than healthy subjects.

Background: There are major air pollution monitoring gaps in sub-Saharan Africa. Developing capacity in the region to conduct air monitoring in the region can help estimate exposure to air pollution for epidemiology research. The purpose of our study is to develop a land use regression (LUR) model using low-cost air quality sensors developed by a research group in Uganda (AirQo). Methods: Using these low-cost sensors, we collected continuous measurements of fine particulate matter (PM2.5) between May 1, 2019 and February 29, 2020 at 22 monitoring sites across urban municipalities of Uganda. We compared average monthly PM2.5 concentrations from the AirQo sensors with measurements from a BAM-1020 reference monitor operated at the US Embassy in Kampala. Monthly PM2.5 concentrations were used for LUR modeling. We used eight Machine Learning (ML) algorithms and ensemble modeling; using 10-fold cross validation and root mean squared error (RMSE) to evaluate model performance. Results: Monthly PM2.5 concentration was 60.2 µg/m³ (IQR: 45.4-73.0 µg/m³; median= 57.5 µg/m³). For the ML LUR models, RMSE values ranged between 5.43 µg/m³ - 15.43 µg/m³ and explained between 28% and 92% of monthly PM2.5 variability. Generalized additive models explained the largest amount of PM2.5 variability (R²=0.92) and produced the lowest RMSE (5.43 µg/m³) in the held-out test set. The most important predictors of monthly PM2.5 concentrations included monthly precipitation, major roadway density, population density, latitude, greenness, and percentage of households using solid fuels. Conclusion: To our knowledge, ours is the first study to model the spatial distribution of urban air pollution in sub-Saharan Africa using air monitors developed from the region itself. Non-parametric ML for LUR modeling performed with high accuracy for prediction of monthly PM2.5 levels. Our analysis suggests that locally produced low-cost air quality sensors can help build capacity to conduct air pollution epidemiology research in the region.

The study of turbulent heat transfer in liquid metal flows has gained interest because of applications in several industrial fields. The common assumption of similarity between the dynamical and thermal turbulence, namely the Reynolds analogy, has been proven to be not valid for these fluids. Many methods have been proposed in order to overcome the difficulties encountered in a proper definition of the turbulent heat flux, such as global or local correlations for the turbulent Prandtl number or four parameter turbulence models. In this work we assess a four parameter logarithmic turbulence model for liquid metals based on RANS approach. Several simulation results considering fluids with Pr = 0.01 and Pr = 0.025 are reported in order to show the validity of this approach. The Kays turbulence model is also assessed and compared with integral heat transfer correlations for a wide range of Peclet numbers.

At least one ultrasound is recommended to predict fetal growth restriction and low birthweight earlier in pregnancy. However, in low-income countries imaging equipment and trained manpower are scarce. Hence, we developed and validated a model and risk score to predict low birthweight using maternal characteristics during pregnancy, for use in resource limited settings. We conducted a prospective cohort study among 379 pregnant women in South Ethiopia. A step-wise multivariable analysis was done to develop the prediction model. To improve clinical utility, we developed a simplified risk score to classify pregnant women at high- or low-risk of low birthweight. The accuracy of the model was evaluated using the area under the receiver operating characteristics curve (AUC) and calibration plot. We evaluated the clinical impact of the model using a decision curve analysis across various threshold probabilities. Age at pregnancy, underweight, anemia, height, gravidity, and presence of comorbidity remained in the final multivariable prediction model. The area under the receiver operating characteristics curve (AUC) of the model was 0.83 (95% confidence interval: 0.78 to 0.88). The decision curve analysis shows the model provides a higher net benefit across ranges of threshold probabilities. In general, this study showed the possibility of predicting low birthweight using maternal characteristics during pregnancy. The model could help to identify those at higher risk of having a low birthweight baby. This feasible prediction model would offer an opportunity to reduce obstetric-related complications and thus improving the overall maternal and child healthcare in low- and middle-income countries.

It has been regarded that Vibrio cholerae O1 inhabit in environmental water. As many cholera patients emerge in Kolkata, it has been thought that V. cholerae O1 is easily detected in environmental water in Kolkata. However, the detection of V. cholerae O1 is rare, though other V. cholerae (NAG Vibrio) is constantly detected. To clear the reason for the difference of the detection rate of two Vibrios, we examined the viability of V. cholera O1 and NAG Vibrios in low ionic strength aquatic medium. We observed greater declining viability of V. cholerae O1 possessing cholera toxin gene (ctx) in low ionic strength solution, but the decline of NAG Vibrios non-possessing ctx is small. To evaluate the concerning of ctx in the viability, we examined the viabilities of V. cholerae O1which do not possess ctx and NAG Vibrios possessing ctx under the same condition. The result indicated that the existence of the ctx induces the decrease the viability of the host in low ionic strength solution. The decrease observed in this experiment might relate with the low detection of V. cholerae O1 possessing ctx in environmental water, though NAG Vibrio is constantly detected.

Contemporary architects and the construction industry are trying to cope with increasing requirements concerning energy efficiency and environmental impact. One of the available options is the active utilization of energy gains from the environment, specifically solar energy gains. These gains can be utilized by, for example, solar walls and facades. The solar façade concept has been under development for more than a century. However, it hasn’t achieved widespread use for various reasons. Rather recently the concept was enhanced by the application of transparent insulation materials that have the potential to increase the efficiency of such façades. The presented study evaluates the environmental efficiency of 10 solar façade assemblies in the mild climate of the Czech Republic, Central Europe. The evaluated façade assemblies combine the principles of a solar wall with transparent insulation based on honeycomb and polycarbonate panels. The study applies Life-Cycle Assessment methodology to the calculation of environmental impacts related to the life cycle of the evaluated assemblies. The results indicate that even though there are several limiting factors, façade assemblies with transparent insulation have lower environmental impacts compared to a reference assembly with standard thermal insulation. The highest achieved difference is approx. 84% (in favour of the assembly with transparent insulation) during a modelled 50-year façade assembly service life.

Iron Doped TiO₂ nanoparticles (Fe-TiO₂) were synthesized and photocatalitically investigated under high and low fluence values of UV-radiation. The Fe-TiO₂ physical characterization was performed using X-ray Powder Diffraction (XRD), Brunauer-Emmett-Teller (BET) surface area analysis, Transmission Electron Microscope (TEM), Scanning Electron Microscope (SEM), Diffuse Reflectance Spectroscopy (DRS), and X-Ray Photoelectron Spectroscopy (XPS) technique. The XPS evidenced that ferric ion (Fe³⁺) was in the lattice of TiO₂ and co-dopants no intentionally added were also present due to the precursors of the synthetic method. The Fe³⁺ concentration played a key role in the photocatalytic generation of hydroxyl radical (•OH) and estriol (E3) degradation. Fe-TiO₂ materials accomplished E3 degradation, and it was found that the catalyst with 0.3 at. % content of Fe (0.3 Fe-TiO₂) enhanced the photocatalytic activity under low UV-irradiation compared with no intentionally Fe-added TiO₂ (zero-iron TiO₂) and Aeroxide^® TiO₂ P25. Furthermore, the enhanced photocatalytic activity of 0.3 Fe-TiO₂ under low UV-irradiation may have applications when radiation intensity must be controlled, as in medical applications, or when strong UV absorbing species are present in water.

Global warming and climate change have led to extreme changes in climatic conditions in recent years. The Taiwan government designates the construction of the Kinmen County as low carbon islands, to promote the operation of 100 electric motorcycles and battery demonstration. This study combined with island tourism, after boarding the island, visitors can rent electric motorcycles from the passenger service center and coordinate with the island tour map to show the location of the battery exchange points, so as to facilitate the search. During the operation, the amount of electric motorcycle lease is 15,551 times, the total mileage of motor vehicle is 284,404 km, the number of battery exchange is 622 times, the lease income is about NT$900,000. To reduce carbon and economic benefits of the assessment, compared to the motorcycles (50 c.c), electric motorcycles (EM 100) can reduce the carbon emissions by 8,726 kg, reducing energy costs of NT$422,594.

Metal-Organic Frameworks (MOFs) are a subclass of porous materials that have unique properties such as varieties of structures from different metals and organic linkers, tunable porosity from a structure or framework design, etc. Moreover, modification/functionalization of the material structure could optimize the material properties and demonstrate high potential for a selected application. MOF materials exhibit exceptional properties and make these materials widely applicable including in energy storage and heat transformation applications. This review aims to give a broad overview of MOFs and their development as adsorbent materials having the potential for heat transformation applications. We summarize current investigations, developments, and possibilities of metal-organic frameworks (MOFs) especially the tuning of the porosity and hydrophobic/hydrophilic design required for this specific application. These materials applied as adsorbent are promising in the thermal driven adsorption for heat transformation using water as working fluid and related application.

The present study examined and compared the effects of high- and low-molecular weight (MW) chitosan, a nutraceutical, on intestinal and liver lipid metabolism in rats fed with high-fat diet. Both high- and low-MW chitosan decreased liver weight, elongated small intestine, improved the dysregulation of blood lipids and liver fat accumulation, and increased fecal lipid excretion in high-fat diet-fed rats. Supplementation of both high- and low-MW chitosan significantly inhibited the decreased phosphorylated AMP-activated protein kinase (AMPK)α and peroxisome proliferator-activated receptor (PPAR)α protein expressions and the increased lipogenesis/cholesterogenesis-associated protein expressions (sterol regulatory element binding protein (SREBP)1c, SREBP2, and PPARγ) and the decreased apolipoprotein (Apo)E and microsomal triglyceride transfer protein (MTTP) protein expressions in the livers of high-fat diet-fed rats. Both high and low-MW chitosan supplementation could also suppress the increased MTTP protein expression and the decreased angiopoietin-like protein (Angptl)4 protein expression in the intestines of high-fat diet-fed rats. Comparison between high and low-MW chitosan, high-MW chitosan has a higher efficiency than low-MW chitosan on the inhibition of intestinal lipid absorption and the increase of hepatic fatty acid oxidation, which can improve liver lipid biosynthesis and accumulation.

The effect of the acetylene and hydrogen gases mixture ratios in direct low-temperature vacuum carburization was investigated. The gas ratio is an important parameter for producing the free radicals in the carburization. The free radicals can remove the natural oxide film by the strong reaction of the hydrocarbons, and then thermodynamically activity can be increased. When the gas ratio was below 1, the supersaturation expanded austenite layers were formed on the surface of the AISI 316L stainless steel, which had the maximum carbon solubility up to 11.5 at.% at 743 K, were formed. On the other hand, when the gas ratio was above 1, the carbon concentration of them remained low even if the process time was enough increased to reach the maximum carbon solubility. As a result, the carbon concentration underneath the surface was determined to be highly dependent on the gas mixture ratio of acetylene and hydrogen. In conclusion, it is necessary to restrict the ratio of acetylene and hydrogen gases to total mixture gases to form the expanded austenite layer with the high carbon concentration in the direct low-temperature vacuum carburization.

Clinical rehabilitation and sports performance analysis both require the objectification of movement. Kinovea^© is a free 2D motion analysis software that enables the establishment of kinematics parameters. This low-cost technology has been used in sports sciences, as well as clinical field and research work. Although it has been validated as a tool with which to assess time-related variables, this is not yet the case regarding angular and distance variables. The main objective of this study was to determine the validity and reliability of the Kinovea software in obtaining angular and distance data at different perspectives of 90°, 75°, 60° and 45°. For this purpose, a figure with 29 points was designed (in AutoCAD) and 24 frames analysed. Each frame was examined by three observers who each made two attempts. For each export data item, 20 angles and 20 distance variables were calculated, with intra- and inter-observer reliability also analysed. To evaluate Kinovea reliability and validity a multiple approach was applied involving the following analysis: -systematic error with a two-way ANOVA 2x4; -relative reliability with ICC and CV (95% confidence interval); -absolute reliability with Standard Error. The results thus obtained indicate that the Kinovea software is a valid and reliable tool that is able to measure accurately at distances up to 5 m from the object and at an angle range of 90°–45°. Nevertheless, for optimum results an angle of 90° is suggested.

Continued high rates of both under- and over-nutrition in low- and low-middle-income countries highlight the importance of understanding dietary practices such as early and exclusive breastfeeding, and dietary patterns such as timely, appropriate complementary feeding—these behaviors that are rooted in complex cultural ecologies. A systematic review and synthesis of available qualitative research related to infant and young child dietary patterns and practices from the perspective of parents and families in low income settings is presented, with a focus on barriers and facilitators to achieving international recommendations. Data from both published and grey literature from 2006-2016 was included in the review. Quality assessment consisted of two phases (CASP guidelines and assessment using GRADE-CERQual), followed by synthesis of the studies identified, and subsequent thematic analysis and interpretation. The findings indicated several categories of both barriers and facilitators, spanning individual and system level factors. The review informs efforts aimed at improving child health and nutrition, and represents the first such comprehensive review of the qualitative literature, uniquely suited to understanding complex behaviors leading to infant and young child dietary patterns.

The creep behaviors of TA2 and R60702 at low and intermediate temperature were presented and discussed in this paper. Experimental results indicated that an apparent threshold stress exhibited in the creep deformation of R60702. Meanwhile, the primary creep phase was found as the main pattern in the room temperature creep behavior of TA2. Compared with exponential law, the power law has been proved to be a proper constitutive model in the description of primary creep phase. It also showed that θ projection method had its significant advantage in the evaluation of accelerated creep stage. Thus, a composite model which combined power law with θ projection method was applied in the creep curves evaluation at low and intermediate temperature. Based on the multiaxial creep deformation results, the model was modified and discussed. A linear relationship existed between composite model parameters and applied load. Finally, the creep life could be accurately predicted and the composite model method is suitable for application in low and intermediate temperature creep life analysis.