Metal 3D printing technology is a promising manufacturing method. The quality of the printed product can pass for mechanical application, if the anisotropy of the microstructure, imperfections, deformation, and residual stress of the printed sample could be lower than the appropriate level or if they are fully illuminated. Thermal stress is one of the significant reasons for deformation in the 3D printed samples. Thermal stresses are the direct consequence of the local temperature gradient. In this research, the effect of the temperature printer’s chamber (from room temperature to 900 C) was studied on thermal stress and subsequent total deformation in the printed sample. The printed sample is a six-layers-printed walk, which could be considered as a building block of other complex shapes and give us inside about deformation. The computational results show a meaningful reduction in thermal stress and deformation at the higher temperature of the printer’s chamber. The lower final deformation of the printed sample is an important subject, especially for samples with complex shapes.

3D surface scans were carried out to determine the shapes of the upper sections of (skeletal) crania of adult Eurasian otters (Lutra lutra) from Great Britain. Landmark points were placed on these shapes by using a graphical user interface (GUI) and distance measurements (i.e., the length, height, and width of the crania) could be found by using the landmark points. These “GUI-based” distances were shown to be accurate and reliable in comparison to physical measurements taken on the crania directly by using a digital calliper. The crania of males were 6.85mm, 5.44mm, 1.66mm larger in terms of length, width and height, respectively, than females in our sample (P < 0.001), i.e., male otters had significantly larger skulls than females. Significant differences in size occurred also by geographical area in Great Britain (P < 0.05). Multilevel Principal Components Analysis (mPCA) indicated that sex and geographical area explained 31.1% and 9.6% of shape variation in “unscaled” shape data and that they explained 17.2% and 9.7% of variation in “scaled” data. The first mode of variation at level 1 (sex) correctly reflected size changes between males and females for “unscaled” shape data. Modes at level 2 (geographical area) also showed possible changes in size and shape. Clustering by sex and geographical area was observed in standardised component scores. Such clustering in cranial shape by geographical area might reflect genetic differences that are known to occur in otter populations in Great Britain, although other potentially confounding factors (e.g. population age-structure, diet, etc.) might also drive regional differences. Furthermore, sample sizes per group were small for geographical comparisons. However, this work provides a successful first test of the effectiveness of 3D surface scans and multivariate methods such as mPCA to study the cranial morphology of otters.

In this study, a three-dimensional bioelectrochemical reactor system (3D-BERs) with granular activated carbon (GAC) epitomizes a novel treatment technology for treating nitrate-polluted water. The conventional denitrification process faces many challenges, including the huge demand for organic carbon, long-term accumulation of intermediate products, and the adaptation period. Results shown that under the optimal conditions of the COD/NO3--N ratio was 1.5, the denitrification efficiency reached 98.62%, when compared to 81.12% at COD/ NO3--N ratio of 3.5, and the initial pH of 7.5 ± 0.5, NO3--N was entirely removed at 2.2 h without accumulation of nitrite. The high initial ratio of NO2--N/NO3--N is mainly to accelerate the denitrification rate by accelerating the reduction of nitrite. Denitrification process followed by zero-order kinetics linear model for at different concentrations of inlet NO3--N, and achieved higher denitrification rate at greater inlet NO3--N concentration. High-throughput sequencing shows that the community structure and relative abundance of bacteria changed significantly, especially at the genes and the phyla level in immobilized GAC particles. Microbial composition enhanced the removal of nitrogen at the inner surface (IS) and bottom surface (BS) of immobilized GAC carriers. Therefore, this system is expected to be a more efficient and useful supplement or a cost-effective alternative compared to the traditional low carbon to nitrogen wastewater treatment system.

Detailed kinetics for a 3-wavelength photopolymerization confinement (PC) system is presented for both numerical solutions and analytic formulas. The dynamic profiles are simulated for oxygen, free radical, and conversion for various situations of: blue-light only, 2-light (red and UV), and 3-light (red, blue, UV). An effective PC requires two conditions: (i) a strong N-inhibition for uncured regime with a low conversion (triggered by the UV-light); and (ii) a weak S-inhibition (oxygen-induced) for high conversion under the blue-light or blue and red-light initiation. Good PC candidates are governed by collective factors of: (i) the double ratio of light-intensity and initiator-concentration, (ii) monomers rate-constant; and (iii) effective absorption constants at specific wavelength and initiators. A new reverse feature for the role of N-inhibition on the blue-conversion is found. Higher oxygen concentration leads to a lower conversion, which could be enhanced by reducing the S-inhibition via a red or blue-light pre-irradiation, having a pre-irradiation time TP=200 s for red-light only, and reduced to 150 s, when both red and blue-light. System under UV-only leads a conversion lower than that of blue-only. However, conversion could be improved by the dual-light (blue and UV), and further enhanced by the pre-irradiation of red-light. The two competing factors, N-inhibition and S-inhibition, could be independently and selectively tailored to achieve: (a) high conversion of blue-light (without UV-light), enhanced by red-light pre-irradiation for minimal S-inhibition; and (b) efficient PC initiated by UV-light produced N-inhibition for reduced confinement thickness and for high print speed.

This paper aims to analyse the mechanical properties response of polylactic acid (PLA) parts manufactured through fused filament fabrication. The influence of six manufacturing factors (layer height, filament width, fill density, layer orientation, printing velocity, and infill pattern) on the flexural resistance of PLA specimens is studied through an L27 Taguchi experimental array. Different geometries have been tested on a four-point bending machine and on a rotating bending machine. From the first experimental phase, an optimal set of parameters deriving in the highest flexural resistance have been determined. Results show that layer orientation is the most influential parameter, followed by layer height, filament width, and printing velocity, whereas the fill density and infill pattern show no significant influence. Finally, the fatigue fracture behaviour is evaluated and compared with previous studies results, to present a comprehensive study of the mechanical properties of the material under different kind of solicitations.

The kinetics and modeling of dual-wavelength controlled photopolymerization confinement (PC) are presented and measured data are analyzed by analytic formulas and numerical data. The UV-light initiated inhibition effect is strongly monomer-dependent and different monomers have different C=C bond rate constants and conversion efficacy. Without the UV-light, for a given blue-light intensity, higher initiator concentration (C₁₀) and rate constant (k’) lead to higher conversion, as also predicted by analytic formulas, in which the total conversion rate (R_T) is an increasing function of k’R, which is proportional to k[gB₁C₁]^0.5. However, the coupling factor b₁ plays a different role that higher b₁ leads to higher conversion only in the transient regime; whereas higher b₁ leads lower steady-state conversion. For a fixed initiator concentration C₁₀, higher inhibitor concentration (C₂₀) leads to lower conversion due to stronger inhibition effect. However, same conversion reduction was found for the same H-factor of H₀ = [b₁C₁₀ - b₂C₂₀]. Conversion of blue-only are much higher than that of UV-only and UV-blue combined, in which high C₂₀ results a strong reduction of blue-only-conversion, such that the UV-light serves as the turn-off (trigger) mechanism for the purpose of spatial confirmation within the overlap area of UV and blue light. For example, UV-light controlled methacrylate conversion of a glycidyl dimethacrylate resin formulated with a tertiary amine co-initiator, and butyl nitrite, subject to a continuous exposure of a blue light, but an on-off exposure of a UV-light. Finally, we developed a theoretical new finding for the criterion of a good material/candidate governed by a double ratio of light-intensity and concentration, [I₂₀C₂₀.]/[I₁₀C₁₀].

3D city models are being extensively used in applications such as evacuation scenarios and energy consumption estimation. The main standard for 3D city models is the CityGML data model which can be encoded through the CityJSON data format. CityGML and CityJSON use polygonal modelling in order to represent geometries. True topological data structures have proven to be more computationally efficient for geometric analysis compared to polygonal modelling. In a previous study, we have introduced a method to topologically reconstruct CityGML models while maintaining the semantic information of the dataset, based solely on the combinatorial map (C-Map) data structure. As a result of the limitations of C-Map's semantic representation mechanism, the resulting datasets could suffer either from semantic information loss or the redundant repetition of them. In this article, we propose a solution for a more efficient representation of both geometry, topology and semantics by incorporating the C-Map data structure in the CityGML data model and implementing a CityJSON extension to encode the C-Map data. In addition, we provide an algorithm for the topological reconstruction of CityJSON datasets to append them according to this extension. Finally, we apply our methodology to three open datasets in order to validate our approach when applied to real-world data. Our results show that the proposed CityJSON extension can represent all geometric information of a city model in a lossless way, providing additional topological information for the objects of the model.

Abstract: The broad clinical use of synthetic vascular grafts for vascular diseases is limited by their thrombogenicity and low patency rate, especially for vessels with a diameter inferior to 6 mm. Alternatives such as tissue-engineered blood grafts (TEBGs) have gained increasing interest. Among the different manufacturing approaches, 3D bioprinting presents numerous advantages and enables the fabrication of multi-scale, multi-material, and multicellular tissues with heterogeneous and functional intrinsic structures. Extrusion-, inkjet- and light-based 3D printing techniques have been used for the fabrication of TEBG out of hydrogels, cells, and/or solid polymers. This review discusses the state-of-the-art research on the use of 3D printing for TEBG with a focus on the biomaterials and deposition methods.

The sTetro is a stair cleaning robot which can climb the staircase with its shapeshifting capabilities. As this robot is intended to traverse multi-floor environment autonomously, hence its localization/positioning information is an essential component of the overall system. Usually, the indoor mobile robots rely on some external system for localization information, e.g., WiFi, UWB, vision, RFID signals, or indoor Global Positioning System (GPS). This requires the installation of additional hardware and/or modification of the working environment for precise positioning information of the mobile platform. As the dimensions of the staircase are known a priori, this knowledge can be used to localize the sTetro robot on the stairs. In this article, the geometry of the staircase has been exploited to localize the robot in 3D space with measurements from the onboard time-of-flight (ToF) range sensors only. The heading angle of the robot is also estimated with two ToF sensors installed in front of the sTetro robot. Results achieved by conducting experiments on real robot prove the efficacy of the proposed approach.

This paper investigates the effects of air void topology on hydraulic conductivity in asphalt mixtures with porosity in the range 14%-31%. Virtual asphalt pore networks were generated using the Intersected Stacked Air voids (ISA) method, with its parameters being automatically adjusted by the means of a differential evolution optimisation algorithm, and then 3D printed using transparent resin. Permeability tests were conducted on the resin samples to understand the effects of pore topology on hydraulic conductivity. Moreover, the pore networks generated virtually were compared to real asphalt pore networks captured via X-ray Computed Tomography (CT) scans. The optimised ISA method was able to generate realistic 3D pore networks corresponding to those seen in asphalt mixtures in term of visual, topological, statistical and air void shape properties. It was found that, in the range of porous asphalt materials investigated in this research, the high dispersion in hydraulic conductivity at constant air void content is a function of the average air void diameter. Finally, the relationship between average void diameter and the maximum aggregate size and gradation in porous asphalt materials was investigated.

Intercellular transport of auxin is driven by PIN-formed (PIN) proteins. PINs are localized at the plasma membrane (PM) and on constitutively recycling endomembrane vesicles. Therefore, PINs can mediate auxin transport either by direct translocation across the PM or by pumping it into secretory vesicles (SVs), leading to its secretory release upon fusion with the PM. Which of these two mechanisms dominates is a matter of debate. Here we addressed the issue with a mathematical modeling approach. We demonstrate that the efficiency of secretory transport depends on SV size, half-life of PINs on the PM, pH, exocytosis frequency and PIN density. 3D-SIM microscopy was used to determine PIN density on the PM. Combing this data with published values of the other parameters, we show that the transport activity of PINs in SVs would have to be at least 1000x greater than on the PM in order to produce a comparable macroscopic auxin transport. If both transport mechanisms operated simultaneously and PINs were equally active on SVs and PM, the contribution of secretion to the total auxin flux would be negligible. In conclusion, while secretory vesicle-mediated transport of auxin is intriguing and theoretically possible model, it unlikely to be a major mechanism of auxin transport in planta.

Purpose: The aim of the present experimental 3D-finite element study was to evaluate the influence of an augmented sinus lift with an additional inserted bone graft block. The bone graft block stabilizes the implant in addition to conventional augmented bone. We placed the block in three different positions. The implants were loaded with axial force and forces secondary to laterotrusion and protrusion. Material and Methods: A simplified U-shaped 3D finite element model of the upper jaw and a more complex anatomical model of the left maxilla were created. The bone graft block was placed in three positions: in the lower third in contact with the sinus floor, the middle, and the upper third of the implant. Van Mises’ stress distribution was calculated and analyzed for the different models. We also compared the complex anatomical model with the simplified one. Results: The position of the bone graft block significantly influences the magnitude of stress distribution. A bone graft block positioned in the upper third or middle of the implant reduces the quantity of stress compared to the reference model without a bone graft block. The low bone graft block position is clearly associated with lower stress distribution in compact bone. We registered no significant differences in stress in compact bone with regard to laterotrusion or protrusion. Conclusions: Maximum values of von Mises stresses in compact bone can be reduced significantly by using a bone graft block. The reduction of stress is nearly the same for positions in the upper third and the middle of the implant. It is much more pronounced when the bone graft block is in the lower third of the implant near the sinus floor, which appeared to be the best position in the present study.

Polyetheretherketone is a promising material for implants due to its good mechanical properties and excellent biocompatibility. Its accessibility to a wide range of applications is facilitated by the ability to process it with an easy-to-use manufacturing process such as Fused Filament Fabrication. The elimination of disadvantages associated with the manufacturing process, such as a poor surface quality, is a main challenge to deal with. As part of the mass finishing process, centrifugal disc finishing has demonstrated good results in surface optimization, making it a promising candidate for post-processing of additively manufactured parts. The objective of this study is to identify the key parameters of the centrifugal disc finishing process on the waviness of additively manufactured PEEK specimen, which has not been investigated yet. Waviness of the specimen was investigated by means of confocal laser scanning microscopy (CLSM), while weight loss was additionally tracked. Six parameters were investigated: type, amount and speed of media, use of compound, amount of water and time. Type of media, time and speed were found to significantly influence waviness reduction and weight loss. Surface electron microscopy images demonstrated the additional effects of deburring and corner rounding. Results on previous studies with specimens made of metal showed similar results. Further investigation is required to optimise waviness reduction and polish parts in a second post-processing step.

The rapid advancement of 3D printing technology has revolutionized the fabrication of microneedle arrays (MNAs), which hold great promise in biomedical applications such as drug delivery, diagnostics, and therapeutic interventions. This review provides an exploration of the diverse materials used in the production of 3D-printed MNAs, including photopolymer resins, biocompatible materials, composite resins, and cutting-edge materials designed to improve mechanical properties, biocompatibility, and functional performance. By analyzing recent research and technological innovations, this paper presents an assessment of material characteristics, fabrication techniques, and their alignment with application-specific requirements. Additionally, it discusses future directions and addresses potential challenges in advancing the field of 3D-printed MNAs.

In this study, we aimed to investigate the differences in tissue surface adaptation and the variations in distances between reference points on the polished surfaces of 3D-printed denture bases with different build angles. The build angles were 0°, 30°, 60°, and 90°, with 15 denture bases printed for each angle. Using the Geomagic Control® software, a 3D best-fit alignment was conducted between the denture base tissue surface and the reference shape of the edentulous maxilla model to calculate the root mean square error. The distances between reference points on the polished surface were measured using digital calipers. One-way analysis of variance was conducted for statistical analysis. The adaptation, as measured by the root mean square error, varied significantly among denture bases with different build angles. The distances between the anterior and posterior reference points of the polished surface were also significantly different. However, within the limitations of this study, the variations in adaptations and dimensional accuracy across different build angles were within clinically acceptable ranges. In clinical practice, the print angle can be adjusted based on factors, such as printing time, resin consumption, and the number of denture bases being printed simultaneously.

This review investigates the pivotal challenge of recycling material waste in the context of Additive Manufacturing with an emphasis on decentralized 3D printing, shedding light on its environmental and economic implications. With additive manufacturing experiencing exponential growth, the environmental impacts of waste generation during 3D printing processes have become increasingly significant. The paper explores various recycled materials commonly used in 3D printing, including polymers like polylactic acid (PLA), acrylonitrile butadiene styrene (ABS), and polyethylene terephthalate glycol (PETG), evaluating their characteristics and usability. General recycling methodologies, encompassing mechanical and chemical processes, are examined with attention to challenges such as polymer sorting, additives, coatings, contamination, and thermoset reprocessing. The economic and societal impact of integrating recycled materials into 3D printing and the environmental impacts are examined. By identifying research gaps and proposing future trends, this review contributes to a deeper understanding of how recycling can play a pivotal role in achieving environmental sustainability and economic viability within the decentralized 3D printing landscape.

The application of three-dimensional (3D) printing/bioprinting technologies and cell therapies has garnered significant attention due to their potential in the field of regen-erative medicine. This paper aims to provide a comprehensive overview of 3D print-ing/bioprinting technology and cell therapies, highlighting their results in diverse medical applications, while also discussing the capabilities and limitations of their com-bined use. The synergistic combination of 3D printing and cellular therapies has been recognised as a promising and innovative approach, and it is expected that these tech-nologies will progressively assume a crucial role in the treatment of various diseases and conditions in the foreseeable future. This review concludes with a forward-looking perspective on the future impact of these technologies, highlighting their potential to revolutionize regenerative medicine through enhanced tissue repair and organ re-placement strategies.

This study aims to propose a method for constructing basic digital twin data in South Korea by adhering to international standards and utilizing publicly available data. Specifically, the study focuses on designing and proposing a digital twin data model for buildings, which are the most applicable among the basic digital twin data. To achieve this, the first section provides essential background information, introduces concepts and requirements related to digital twin basic data, and offers a brief overview of CityGML. The second section explains the methodology and data used in this study. The third section presents the main findings: the selection of public data (buildings) for constructing digital twin basic data, the mapping process using CityGML, and the creation of UML diagrams. The fourth section discusses these findings. Finally, the conclusion and suggestions for future research are provided. This approach enhances the accuracy of building-related digital twin data and supports the use of digital twin services in both public and private sectors by enabling various spatial analyses.

The article presents the results of the technical-economical study regarding the optimization of the FDM parameters (Lh – the height of the layer deposited in one pass and Id – the filling percentage) for the manufacture of PETG and ASA parts. To carry out the technical-economical study, we used the fundamental principle of value analysis, which consists in maximizing the ratio between Vi/Cp, where Vi - represents the mechanical characteristic, and Cp - represents the production cost. The results of the study show that for the tensile specimens made of PETG, the parameter that significantly influences the results of the Vi/Cp ratios is Lh, and in the case of the compression specimens made of PETG, the parameter that significantly influences the results of the Vi/Cp ratios is Id. In the case of specimens manufactured by FDM from ASA, the parameter that decisively influences the results of the Vi/Cp ratios of the tensile and compression specimens is Id – the filling percentage. By performing optimization of the process parameters with multiple responses, we identified the optimal parameters for FDM manufacturing of parts from PETG and ASA: Lh = 0.20 mm and Id = 100%.

The study aimed to analyze thoracic and lumbar erector spinae muscle activations during 3D elongation exercises in individuals with adolescent idiopathic scoliosis (AIS). Participants included 24 adolescents, meeting specific criteria such as a Cobb angle between 10° and 20°, and not having undergone surgical or brace treatments. EMG data were collected to evaluate muscle activations. The study found no significant interaction between exercise type and the side of the curve, but a significant main effect of exercise type on muscle activation, irrespective of Cobb angle. Different exercise types significantly affected muscle activity, with the highest activations in the TheraBand exercise, followed by manual and without equipment conditions. This suggests that exercise type significantly impacts muscle engagement in AIS patients, providing valuable insights for targeted exercise program design. The study, however, focused on short-term muscle activation, not long-term Cobb angle progression, pointing to the need for further research in this area.

Fused deposition modeling (FDM) is widely applied in various fields due to its affordability and ease of use. However, it faces challenges such as achieving high surface quality, precise dimensional tolerance and overcoming anisotropic mechanical properties. This paper analyzes and compare the machinability of 3D printed PLA, PETG and carbon fiber reinforced PETG focusing on surface roughness and burr formation. A design of experiments (DoE) with a full factorial design was used, considering three factors: rotation speed, feed rate and depth of cut. Each factor had different levels: rotational speed at 3000, 5500 and 8000 rpm; feed rate at 400, 600 and 800 mm/min; and depth of cut at 0.2, 0.4, 0.6, and 0.8 mm. Machinability was evaluated by roughness and burr height using a profilometer for all the materials under the same milling conditions. To evaluate the statistical significance of the influence of various processing parameters on surface roughness and burr formation in 3D printed components made of three different materials PLA, PETG and carbon fiber reinforced PETG, an analysis of variance (ANOVA) test was conducted. This analysis investigated whether variations in rotational speed, feed rate and depth of cut resulted in measurable and significant differences in machinability results. Results showed that milling parameters significantly affect roughness and burr formation, with optimal conditions for minimizing any misalignment highlighting the trade-offs in parameter selection. These results provide insights into the post-processing of FDM-printed materials with milling, indicating the need for a balanced approach to parameter selection based on application-specific requirements.

Background: Removable prostheses have seen a fundamental change recently because of advances in polymer materials, allowing improved durability and performance. Despite these advancements, notable differences still occur amongst various polymer materials and processing technologies, requiring a thorough grasp of their mechanical, physical, and therapeutic implications. Methods: Fours different processing techniques, all utilizing Polymethyl methacrylate (PMMA) as the main material, were used to construct complete dentures. The specimens underwent a mechanical test. Results: All the specimens broke under the influence of a certain force, rather than yielding through flow, as is characteristic for plastic materials. For each specimen, the maximum force (N) was recorded (figure 4), as well as the breaking energy, Conclusions: The best results were obtained in the case of the thermoplastic injection system and, surprisingly and contrary to those in the specialized literature, the worst results were recorded in the case of 3D printed samples.

Drug-induced liver injury (DILI) stands as a significant cause of drug attrition. To mitigate clinical DILI risks, assessing drugs using human liver models is crucial since animal studies may fall short due to species-specific liver pathway variations. Cell-based preclinical hepatotoxicity testing is often pertinent. In the present study, cells from a human liver cancer line (HepG2, HepaRG) were cultured in both formats of 2D and 3D spheroids to explore their responses to drugs. Liver-specific marker expressions across cell lines and culture formats were also examined to assess disparities in drug-induced liver injury marker expressions. In cytotoxicity assays, HepG2 cells exhibited heightened sensitivity to amiodarone HCl, while HepaRG cells showed greater sensitivity to acetaminophen. Generally, 2D cultures were more responsive to drugs than 3D cultures. Consistency was observed between cytotoxicity assays and liver injury markers AST and ALT. Variations were also noted in liver cell marker secretion, with albumin and urea concentrations declining post-drug treatment, particularly with higher baseline expression in HepaRG cells and 3D cultures. Additionally, mRNA expression levels of CYP enzymes involved in hepatocellular drug metabolism were compared following treatment with enzyme inducers. CYP1A2 and CYP2C9 were not expressed in HepG2 cells. On the other hand, CYP3A4 was expressed higher in 3D culture than in 2D culture. HepaRG cells exhibited significantly increased expression of all three enzymes post-treatment. Notably, enzyme expression was notably higher in 3D cultures than in 2D cultures. Collectively, these findings suggest that HepaRG cells and 3D cultures hold promise for evaluating DILI during early-stage drug development.

This study explores novel techniques to improve the detection accuracy of skarn iron deposits using advanced image processing methodologies. Leveraging the capabilities of Aster image, Band Ratio (BR) images, and Principal Component Analysis (PCA), alongside the power of 3D Convolutional Neural Networks (3D-CNN), the research aims to enhance the precision and efficiency of ore detection in complex geological environments. The proposed method employs a specific 3D-CNN architecture, accepting input as a 7×7×C image patch, where C represents the combined number of selected Aster image bands, Principal Component (PC) bands, and computed BR images. To evaluate the accuracy of the proposed method, five distinct image bands combinations, including the proposed bands combination, were tested and evaluated based on the overall accuracy (OA), average accuracy (AA), and kappa coefficient. The results demonstrated that while the incorporation of BR images alongside Aster bands initially seemed promising, it introduced significant confusion in certain classifications, leading to unexpected mis-classification rates. Surprisingly, utilizing solely Aster bands as input parameters yielded higher accuracy rates (OA= 93.13%, AA = 91.96%, Kappa = 90.91%) compared to scenarios involving the integration with band ratios (OA = 87.02%, AA = 79.15, and Kappa = 82.60%) or the integration of BR images to PC bands (OA= 87.78%, AA = 82.39%, Kappa = 83.81%). However, the amalgamation of Aster bands with selected PC bands showed slight improvements in accuracy (OA= 94.65%, AA = 92.93%, Kappa = 93.45%), although challenges in accurately classifying certain features persisted. Ultimately, the proposed combination of Aster bands, PC bands, and BR images (proposed bands combination) presented the most visually appealing and statistically accurate results (OA = 96.95%, AA= 94.87%, and Kappa = 95.93%), effectively addressing misclassifications observed in the other combinations. These findings underscore the synergistic contributions of each of the Aster bands, PC bands, and BR images, with Aster bands proving pivotal for optimal skarn classification, PC bands enhancing intrusions classification accuracy, and BR images strengthening wall rock classification accuracy. In conclusion, the proposed combination of input image bands emerges as a robust and comprehensive methodology, demonstrating unparalleled accuracy in the remote sensing detection of skarn iron minerals.

The integration of three-dimensional (3D) printed resin denture teeth represents a significant ad-vancement in digital dentistry. This study aimed to assess their ability to withstand chipping and indirect tensile fractures, comparing them with conventionally manufactured resin denture teeth. Four groups, each comprising 30 specimens, were examined: Group 1 featured 3D printed denture teeth (NextDent, 3D Systems, Soesterberg, The Netherlands), while the others included commer-cially obtained Ivostar Shade, SpofaDent Plus, and Major Super Lux teeth. Stereolithography 3D printing was utilized to produce methacrylate-based photopolymerized resin teeth models for Group 1, while the remaining groups were commercially sourced. Chipping and indirect tensile fracture tests were performed at a speed of 1 mm/min until fracture occurred. Statistical analysis was conducted using one-way analysis of variance (ANOVA) with Tukey's honestly significant difference multiple comparisons test (p < 0.05). Results indicated that 3D-printed teeth exhibited higher indirect tensile fracture resistance than Major Super Lux and Ivostar Shade but lower than SpofaDent Plus. Additionally, in the chipping test, buccal chipping occurred in 3D-printed resin teeth without distortion. In the indirect tensile test, the fracture line emerged near the loading point, extending cervically from the inner incline of both cusps. Overall, denture teeth produced via 3D printing with printable resin materials demonstrated sufficient fracture resistance, making them suitable for prosthetic applications.

Verifying the accuracy of a 3D-printed object involves using an image processing system. This system compares images of the CAD model of the object to be printed with its 3D-printed counterparts to identify any discrepancies. It is important to note that the integrity of the accuracy measurement is heavily dependent on the image processing settings chosen. This study focuses on this issue by developing a customized image processing system. The system generates binary images of a given CAD model and its 3D-printed counterparts and then compares them pixel-by-pixel to determine the accuracy. Users can experiment with various image processing settings, such as grayscale to binary image conversion threshold, noise reduction parameters, masking parameters, and pixel-fineness adjustment parameters, to see how they affect accuracy. The study concludes that the grayscale to binary image conversion threshold has the most significant impact on accuracy and that the optimal threshold varies depending on the color of the 3D-printed object. The system can also effectively eliminate noise (filament marks) during image processing, ensuring accurate measurements. Additionally, the system can measure the accuracy of highly complex porous structures where the pores size, depth, and distribution are random. The insights gained from this study can be used to develop intelligent systems for the metrology of additive manufacturing.

Wavelength selective switches (WSSs) are essential elements for wavelength division multiplexing (WDM) optical networks, as they offer cost-effective, high port-count and flexible spectral channel switching. This work proposes a new hybrid WSS architecture that leverages the beam shaping and steering features of uniform silicon nitride (SiN) based end-fire optical phased arrays (OPAs). By introducing beamforming to a WSS system, the spectral channels on the liquid crystal on silicon (LCoS) panel can be tailored and arranged properly, depending on the optical configuration, using the beam control capabilities of OPAs. Combining 3D-FDTD and ray tracing simulations, the study shows that by reducing the input beam dimensions with proper sizing of the OPAs, the WSS design with the null-steering OPAs layout and 4×No switch size features increased spectral resolution. This extensive beamforming study on the steering-enabled layout reveals the acquirement of an even higher input channel number, achieving up to the 8×No WSS scheme with flexible channel routing on the LCoS panel. Such implementation of beamsteerers can unlock an extra degree of freedom for the switching capabilities of hybrid WSS devices. The results show great promise for the introduction of OPAs in WSS systems and provide valuable insight for the design of future wireless communication links and WDM systems.

This study investigates the effect of scaffold architecture on bone regeneration, focusing on 3D-printed polylactic acid-bioceramic calcium phosphate (PLA-bioCaP) composite scaffolds in rabbit femoral condyle critical defects. To assess their influence on bone healing and scaffold performance, we explored two distinct scaffold designs, alternate and helical laydown patterns. The scaffolds were meticulously characterized for pore size, strut thickness, porosity, pore accessibility, and mechanical properties. The in vivo efficacy of these scaffolds was evaluated using a rabbit femoral condyle critical defect model. Our findings indicate that both scaffold architectures are biocompatible and support bone formation. The helical scaffolds, characterized by larger pore sizes and higher porosity, demonstrated significantly greater bone regeneration than the alternate structures. However, their lower mechanical strength presented limitations for use in load-bearing sites. This study highlights the importance of scaffold architecture in bone tissue engineering and underscores the need to balance porosity and mechanical strength for optimal bone regeneration. The findings provide crucial insights for the design of 3D- printed scaffolds in clinical applications, particularly in the context of critical-sized bone defects. The study also outlines potential areas for future research, including exploring hybrid scaffold designs to achieve optimal porosity without compromising mechanical integrity.

3D printing is a non-traditional additive manufacturing process. It is different from the traditional subtractive manufacturing process. It offers exceptional rapid prototyping capabilities and results that traditional subtractive manufacturing methods cannot attain, especially in applications involving curved or intricately shaped components. Despite its advantages, metal 3D printing will face porosity, warpage, and surface roughness issues. These issues will affect the future practical application of the parts indirectly, for example, the structural strength and the parts assembly ca-pability. Therefore, this study compares the qualities of the warpage, weight, and surface rough-ness after milling and grinding processes under the same materials (316L stainless steel) between general rolled steel and 3D additive steel. Experimental results show that 3D printing parts are approximately 13% to 14% lighter than the general rolled steel. The surface roughness performance of 3D printing steel is better than general rolled steel under the same material after milling or grinding processing. The hardness of the 3D printing steel is better than that of the gen-eral rolled steel. The research verifies that 3D additive manufacturing can use surface processing to optimize surface performance and achieve the functions of lightness and hardness.

(1) Background: Pseudotumor of the hip is a sterile, non-neoplastic soft tissue mass associated with total hip arthroplasties. Pseudotumors may mimic soft tissue tumors, or infections, so the differential diagnosis is crucial and biopsy is recommended. The purpose of this study was to compare complications and functional results between one-stage and two-stage procedures. (2) Methods: We retrospectively analyzed 21 patients surgically treated at our Institution with “pseudotumor” associated with hip prosthesis (8 male,13 female; mean age 69 years). One-stage revision was performed in 10 cases, two-stage in 10, excision only in one case. Complications were classified as major and minor and functional results assessed using the Harris Hip Score (HHS). (3) Results: Five patients (24%) reported major complications. Survival rate to all com-plications was 75%. Overall survival was 95% at five years. Mean HHS went from 35 pre-operative to 75 post-operative, highlighting improved functional results in all cases. We rec-orded no differences in complications and functional outcome between one and two-stage proce-dures. (4) Conclusions: In our experience, two-stage surgical approach is preferable in cases with major bone defects and larger pseudotumor size. The use of custom-made 3D-printed prostheses is increasing and is a further reason to prefer two-stage revision.

Mycotoxins are secondary metabolites produced by filamentous fungi associated to a variety of acute and chronic foodborne diseases. Current toxicology studies mainly rely on monolayer cell cultures and animal models, which are undeniably affected by several limitations. To bridge the gap between the current in vitro toxicology approach and the in vivo predictivity of the data, we here investigated the cytotoxic effects induced by the mycotoxins sterigmatocystin (STE), ochratoxin A (OTA) and patulin (PAT) on different 2D and 3D cell cultures. We focused on human tumours (neuroblastoma SH-SY5Y cells, and epithelial breast cancer MDA-MB-213 cells) and healthy cells (bone marrow derived mesenchymal stem cells, BM-MSC, and umbilical vein endothelial cells, HUVECs). Cytotoxicity of STE, OTA, and PAT was determined after 24, 48 and 72 h of exposure by ATP assay in both culture models. 3D spheroids morphology was also analysed using the MATLAB-based open-source software AnaSP. Our results highlighted how each cell line and different culture models showed specific sensitivities, reinforcing the importance of using more complex models for toxicology studies and a multiple cell line approach for an improved and more comprehensive risk assessment.

This paper focuses on leveraging a cutting-edge 3D state-space model for a holistic eco-friendly assessment in petrochemical operations. - By applying the ecological carrying capacity theory and the three-dimensional state-space model, this research aims to unleash the next frontier of sustainability in the petrochemical industry. - The proposed methodology will enable advanced and comprehensive eco efficiency evaluation in petrochemical operations. - Through the integration of the ecological carrying capacity theory and advanced modeling techniques, this research seeks to revolutionize sustainability assessments in the petrochemical sector. - The utilization of the cutting-edge 3D state-space model will provide a more advanced and accurate understanding of eco-friendly practices in petrochemical operations. This research presents a unique approach distinct from existing literature, which primarily examines business eco efficiency from behavioral motivation and strategic perspectives. In contrast, this paper introduces a novel three-dimensional state-space model to evaluate the ecological efficiency of petrochemical operations. By combining the ecological carrying index and state space, this model represents the ecological impact of petrochemical operations in a three-dimensional geometric space. It considers petrochemical operations as a significant factor exerting pressure on natural resources and the natural environment. In this three-dimensional state-space model, the three axes represent different dimensions of petrochemical operations. The first axis represents the economic status, which quantitatively describes the financial aspects of the operation. The second axis represents the utilization of resources, capturing the extent to which resources are consumed in the operation. The third axis focuses on the impact of the operation on the environment, allowing for a quantitative assessment of its ecological footprint. By incorporating these dimensions, the model aims to provide a comprehensive and quantitative description of the economic activities of petrochemical operations and their interactions with resources and the environment.The primary focus of this research is to apply the three-dimensional state-space model to calculate the ecological carrying capacity of petrochemical operations. By doing so, it aims to verify the feasibility and applicability of the model in determining the ecological efficiency of these operations. The research also aims to provide theoretical tools that can assist operations in making more informed ecological efficiency judgments. By utilizing this model, petrochemical operations will have a quantitative framework to assess and improve their environmental impact, thus fostering more sustainable practices. The findings of this research demonstrate that the implementation of this method can effectively identify issues related to resources, economy, and environment throughout the development of petrochemical operations. By identifying these problems, it provides managers with a solid foundation for making strategic decisions that promote sustainable development. With this valuable information at their disposal, managers can proactively address challenges, optimize resource utilization, and minimize environmental impacts, thus steering the petrochemical operations towards a more sustainable and responsible path.

Scaffolds for tissue engineering are expected to respond to a challenging combination of physical and mechanical requirements, guiding the research towards the development of novel hybrid materials. This study introduces innovative three-dimensional bioresorbable scaffolds, in which a stiff poly(lactic acid) lattice structure is meant to ensure temporary mechanical support, while a bioactive gelatin-chitosan hydrogel is incorporated to provide a better environment for cell adhesion and proliferation. The scaffolds present a core-shell structure, in which the lattice core is realized by additive manufacturing, while the shell is nested throughout the core by grafting and crosslinking a hydrogel forming solution. After subsequent freeze-drying, the hydrogel network forms a highly interconnected porous structure that completely envelops the poly(lactic acid) core. Thanks to this strategy, it is easy to tailor the scaffold properties for a specific target application, by properly designing the lattice geometry and the core/shell ratio, which are found to significantly affect the scaffold mechanical performance and its bioresorption. Compression stiffness and strength provided by poly(lactic acid) lattices are overall within the range of values displayed by human bone tissue and remain stable after prolonged immersion in water at body temperature for several weeks. On the other hand, the hydrogel undergoes gradual and homogeneous degradation over time, but the core-shell integrity and structural stability are nevertheless maintained during at least 7-week hydrolytic degradation tests. In vitro experiments with human mesenchymal stromal cells reveal that the core-shell scaffolds are biocompatible and their physical-mechanical properties and architecture are suitable to support cell growth and osteogenic differentiation, as demonstrated by hydroxyapatite formation. These results suggest that the bioresorbable core-shell scaffolds can be considered, and further studied, in view of clinically relevant endpoints in bone regenerative medicine.

Abstract: In complex revision total hip arthroplasties, careful preoperative planning is crucial for the proper reconstruction of hip biomechanics. With conventional 2D radiographic images and computed tomography (CT) the 3D extension of the defect and the remaining bone stock may not be evaluated properly. 3D printed models can aid the surgeon in planning complex acetabular re-construction. The purpose of this study is to compare the accuracy of bony defect assessment in severe acetabular defects surgery with 3D printing planning as compared to conventional 2D ra-diographic planning and CT. Twenty-five patients with severe acetabular defects (Paprosky IIC and III) undergoing revision surgery were enrolled. Each patient had a 3D printed model of their femur and pelvis created based on CT scans. Clinical and radiographic assessments were conducted before and after surgery, with four key bone landmarks measured and compared between X-ray, CT, 3D models, and surgical reports. The findings revealed discrepancies in defect assessment between different imaging methods. X-rays and CT scans sometimes incorrectly identified affected areas, while the 3D models showed more accurate results. This study suggests that 3D printed models can significantly improve the preoperative evaluation of complex hip arthroplasty revisions, enabling surgeons to better select optimal surgical strategies.

Blood testing is a crucial application in the field of clinical studies for disease diagnosis and screening, biomarkers discovery, organ function assessment, and personalized medication. Therefore, it is of utmost importance to collect precise data in a short time. In this study, we utilized Raman spectroscopy to analyze blood samples and extracted comprehensive biological information, including the primary components and compositions present in the blood. We conducted short-wavelength (532 nm green light) Raman scattering spectroscopy on blood samples, plasma, and serum, and subsequently analyzed the biological characteristics detected in each sample type. Our results indicated that whole blood had high hemoglobin content, which suggests that hemoglobin is a major component of blood. The characteristic Raman peaks of hemoglobin were observed at 690, 989, 1015, 1182, 1233, 1315, and 1562–1649 cm−1. Analysis of plasma and serum samples indicated the presence of β-carotene, which exhibited characteristic peaks at 1013, 1172, and 1526 cm−1. Additionally, in the field of medical blood testing, the novel 3D Silicon micro-channel device technology holds immense potential. It can serve as a substrate and helps to detect various diseases and biomarkers, providing real-time data to help medical professionals and patients better understand their health conditions. Changes in biological data collected in this manner could potentially be used to diagnose clinical diseases.

This article addresses the need to know the thermal conductivity in different filaments that this FDM technology uses. Because there are multiple applications that these additive manufacturing products play in the field of thermal insulation. For the study of thermal conductivity, the DTC-25 commercial conductivity measurement bench is used, where the tests will be carried out on a set of seven different materials with 100% fabrication density. From base materials such as acrylonitrile butadiene styrene (ABS) or polylactic acid (PLA), materials of high mechanical and thermal resistance, polyether ether ketone (PEEK) and high-performance polyetherimide thermoplastic (ULTEM), to materials with metal inclusions (aluminum 6061) that would later be subjected to thermal aftertreatments. The study shows how the parts manufactured with aluminum inclusion have a higher thermal conductivity, 0.40 ±0.05 W/m·K, compared to another material, such as TPU, of high mechanical and thermal resistance, with a conductivity of 0.26 ±0.05 W/m·K.

(1) Background: Type-2 Diabetes (T2DM) is a long-term medical disorder characterized by Insulin deficiency and high blood glucose levels. Among other medication to cure T2DM, the review of the literature found that various Pyrimidine derivative act as an agonist for G-protein-coupled receptor 119 (GPR119) was proposed to control blood glucose levels by enhancing the function of pancreatic beta-cells and its mechanism of action with fewer adverse effects.; (2) Methods: In the present research work, in-silico investigations were carried out to investigate the potential of Pyrimidine analogue as an agonists to the protein target GPR119 receptor. We performed exhaustive molecular modelling and protein modelling methodologies such as homology mod-elling, molecular docking along with various drug designing tools such as 3D-QSAR and pharmacophore mapping to ascertain the design of better GPR119 agonists.; (3) Results: On the basis of in-depth computa-tional studies, we designed new pyrimidine moiety and analyzed them for GPR-119 receptor agonist and fur-ther explored the ADME properties. Designed compounds found to exhibit better predicted activities as com-pared to reference compound; (4) Conclusions: The current research on pyrimidine derivatives, using molec-ular docking, 3D-QSAR and Pharmacophore mapping demonstrated that the obtained computational model has significant properties and the designed molecules and Dataset from this model, produced antidiabetic compound against the target GPR119 i.e., compound 1S, 1Z and 1D with the docking score of −11.696, -9.314 and -8.721 respectively. The pharmacokinetics and drug-likeness studies revealed that these compounds may be the future candidate for the treatment of diabetes acting via GPR119 agonist mechanism.

Robin sequence is a congenital anomaly characterized by a triad of features that include micrognathia, glossoptosis, and airway obstruction. This comprehensive historical review maps the evolution of approaches and appliances for its treatment from the past until current modern possibilities of interdisciplinary combination of modern engineering, medicine, materials, and computer science combined approach with emphasis to design appliances inspired by nature - individual human anatomy. Current biomimetic designs are clinically applied resulting in appliances that are more efficient, comfortable, sustainable, and safer than legacy traditional designs. Review maps the treatment modalities that have been used for patients with Robin sequence over the years. Early management of Robin sequence focused primarily on airway maintenance and feeding support, while current management strategies involve both nonsurgical and surgical interventions and biomimetic biocompatible personalized appliances. The goal of this paper was to provide a review of the evolution of management strategies for patients with Robin sequence that led to the current interdisciplinary biomimetic approaches impacting the future of Robin Sequence treatment with biomimetics at the forefront.

The aim of this study is to introduce and evaluate a new approach by using 3D printed anthropomorphic breast phantoms in teaching X-ray mammography techniques Radiologic technologists. For this purpose, a physical anthropomorphic breast phantom is created, based on a computational breast version. The phantom is created by a stereolithography 3D printer. The practical exercises were conducted in three sessions with the participation of radiographers students first, second and third year of training, respectively. A survey was prepared to summarise the participants´ opinion about this new form of training in mammography technique. A total of 83 students were trained with the new approach. From these 52 responded to the survey questions. More than half of the students (71.2%) successfully handled the exercise with the physical breast phantom. The training provoked a substantial number of students to express the belief that incorporating modern methods based on digital technologies into their X-ray device training is essential. The instructor was well prepared and with the needed competence. The experience within this training convinces the future professionals to introduce the new technologies in their routine work, particularly for exercising the compression technique and breast positioning.

Unmanned aerial vehicles (UAV) have emerged as a solution to day to day survey tasks, allowing users to visualize phenomena in real-time. This paper explores the capabilities of UAV or drones in the collection of accurate, geo-tagged data quickly, including photogrammetry software processes to deliver standardized data output. In order to explore the capabilities of UAV, Gatu Township in Centenary, Muzabani District of Zimbabwe was chosen from the national mapping topographic series. This study demonstrates the efficiency of data collection using drones, generate 2D orthomosaics in real time, so that analysts can easily visualize land cover and identify any changes, map and model large areas to produce data for 2D and 3D models. The recent development of innovative optical image processing has further lowered the costs high resolution topographic surveys.

This paper presents the use of Graph Neural Networks (GNNs) to predict the tensile strength of Fused Deposition Modeling (FDM) specimens. In the present work, there are four main input parameters i.e. Infill percentage, Layer height, Print speed and Extrusion temperature while the Tensile Strength is an output parameter were considered. This study includes use of central composite design based response surface methodology to finalize the experimental layout. 3D printed specimen were manufactured as per the ASTM E8 standard on FDM printer using Polylactic Acid (PLA) as filament. Micro-tensile test were performed on the printed specimen as per ASTM E8 standard. The GNN algorithm was trained on a dataset of FDM specimens, achieving a mean squared error (MSE) of 2.47, mean absolute error (MAE) of 1.14, and R-squared value of 0.78. An adjacency matrix, which shows the connections between nodes in a graph. The obtained plot for nodes and weights in a GNN provide valuable information about the model and its performance. The results show the potential of using GNNs in predicting the mechanical properties of additively manufactured specimens and provide a promising direction for further research in this field.

The two-phase flow of water and reactive gas in the channel of proton exchange membrane fuel cell (PEMFC) plays an important role in high-quality water management. In this study, the removal effect of 3D wave channel and 2D straight channel for liquid water was studied by volume of fluid method. The dynamic behavior of droplet emerge from the gas diffusion layer (GDL) into the channel under the influence of gas flow was investigated. The effects of droplet growth, deformation, detachment, force, pore size on water critical behavior and water content in the channel are discussed. The results show that the 3D wave channel is superior to the removal of liquid water than the 2D straight channel. The increase of velocity is conducive to the discharge liquid water. While infinite increase of velocity will cause more parasitic power loss. The larger pore size of GDL is not advantageous to the performance of PEMFC, but the appropriate increase of pore size is conducive to the discharge of liquid water. The basic knowledge obtained in this study will help to deepen the understanding of droplet dynamics in PEMFC gas channels, and help to optimize the design and working conditions of these channels.

DEXTER (Detection of EXplosives and firearms to counter TERrorism) is a project funded by NATO’s Science for Peace and Security (SPS) program with the goal of developing an integrated system capable of remotely and accurately detecting explosives and firearms in public places without impeding the flow of pedestrians. The active microwave component of the DEXTER project is referred to as MIC (Microwave Imaging Curtain), supported by the French SGDSN (General Secretariat of Defense and National Security), and utilizes a radar system capable of generating 3D images in real time to address non-checkpoint detection of explosives and fire-arms. The project, led by the ONERA (France), is based on a radar imaging system developed by the Fraunhofer FHR institute, using a MIMO architecture with an Ultra Wide-Band waveform. Although high-resolution 3D microwave imaging is already being used in expensive body scanners to detect firearms concealed under clothing, MIC's innovative approach lies in utilizing a high-resolution 3D imaging device that can detect larger dangerous objects carried by moving individuals at a longer range, in addition to providing discrete detection in pedestrian flow. Automatic detection and classification of these dangerous objects is carried out on 3D radar im-ages using a deep-learning network. This paper will outline the project's objectives and constraints, as well as the design, architecture, and performance of the final system. Additionally, it will present real-time imaging results ob-tained during a live demonstration in a relevant environment.

The paper presents the conceptualization and realization of a novel platform for additive manu-facturing, an industrial robot arm-based system for additive manufacturing applications. Tradi-tional 3D printers, especially those employing fused deposition modelling (FDM) processes, are restricted to depositing material in a single toolpath plane (e.g. x-y plane). The focus of this study was to explore the feasibility of integrating commercial off the shelf (COTS) additive manufac-turing technologies with a six degree of freedom industrial robot arm to yield a 3D additive manufacturing system with the capability to perform free-form six degree of freedom fused deposition modelling. The present paper presents the development of a platform from stage 0, i.e. materials to its use, and finally a printed product with the developed extruder.

This study demonstrates the successful synthesis of Ni/Y2O3 nanocomposite particles through the application of ultrasound-assisted precipitation using the Ultrasonic Spray Pyrolysis technique. The particle size was predicted accurately using a modified equation, and they were collected in a water suspension with Polyvinylpyrrolidone (PVP) as the stabiliser. The presence of the Y2O3 core and Ni shell was confirmed with Transmission Electron Microscopy (TEM) and with electron diffraction. The TEM observations revealed the formation of round particles with an average diameter of 466 nm, while the lattice parameter on the Ni particle’s surface was measured to be 0.343 nm. The Ni/Y2O3 nanocomposite particle suspensions were lyophilized, to obtain a dried material that was suitable for embedding into a Polylactic acid (PLA) matrix. The resulting PLA/Ni/Y2O3 composite material was successfully extruded successfully, so that a 3D printed technology Fused Filament Fabrication could be used further for the production of tensile test tubes. The tensile tests showed that the addition of lyophilised Ni/Y2O3 into the PLA matrix decreased the tensile strength by 21.8 %, while the tensile modulus was not influenced. Dynamic Mechanical Analysis (DMA) showed that the addition of the Ni/Y2O3 particles increased the glass transition temperature by 5 °C, and increased the storage modulus in the glass transition range significantly. These findings demonstrate the potential for utilising Ni/Y2O3 nanocomposite particles in 3D printing applications, and warrant further exploration of their mechanical properties and potential applications in various fields.

A 3D graphene foam made of interconnected multilayer graphene flakes was produced on optical fibres (OF) by laser-induced transformation of a polyimide (PI) film coated on the OF cladding. This material, known as la-ser-induced graphene (LIG), was explored in the electrochemical detection and quantification of dopamine (DA) at physiologically relevant concentrations in the presence of the most relevant interfering molecules in biological fluids, ascorbic acid (AA) and uric acid (UA). The measured limit of detection is 100 nM, the linear range is 0.1 to 5 μM and a maximum sensitivity of 5.0 µA µM−1 cm−2 was obtained for LIG decorated with Pt nanoparticles (NPs). Moreover, immunity to AA and UA interference and to fouling was attained by decorating the LIG elec-trode with Pt NPs and coating with Nafion. These figures of merit underlines the potential of these sensors for the quantification of physiologically relevant concentrations of DA in biological fluids, paving the way for the development of hybrid electrochemical/optical sensing actuating platforms in a lab-on-fibre configuration, with relevant applications in biomedical engineering. The advantages of this hybrid arrangement include the possi-bility of in-situ counterproofing, extended measuring ranges, photoelectrochemical detection and the probing of inaccessible places. This elegant approach can also provide a simple and cost-effective way to fabricate biomed-ical devices with extended functionality, such as medical optical probes with added electrochemical capabilities, optogenetics combined with local electrochemical detection, among others.

Less than half of e-waste plastics is sorted worldwide and this rate is likely to decline as major processing countries have banned importation of e-waste plastics. This forces the development of decentralized processing facilities, also known as microfactories. The present work investigates the recyclability of different grades of acrylonitrile-butadiene-styrene (ABS) copolymer, polycarbonate, and polypropylene, which were found to be very abundant in a recycling site in the UK. The determination of the matrix relied on the resin identification code imprinted in the e-waste plastic and subsequent FTIR analysis. The melt-blend extrusion technology enabled the valorization of the wasted thermoplastics as 3D filament without significant degradation of the polymers. The recycled materials maintained the tensile strength around 2.5 MPa in agreement with the specifications offered by virgin polymers. Further characterization was done by means of laser microscope, thermogravimetric analysis, and XRF to determine the commercial viability of the recycled filament. A modified solvent-based method was developed with acetone to remove the brominated flame retardants: 25g/100mL, 30 minutes of contact time, and 4 extraction steps. The FTIR results show that the degradation of the rubbery dispersed phase corresponding to the butadiene can be accumulated in the less soluble fraction of the waste ABS.

Fluorescence microscopy is an important tool for disease diagnosis, often requiring costly optical components, such as fluorescence filter cubes and high-power light sources. Due to its high cost, conventional fluorescence microscopy cannot be fully exploited in low-income settings. Smartphone-based fluorescence microscopy becomes an interesting low-cost alternative, but raises challenges in the optical system. We present the development of a low-cost inverted laser fluorescence microscope, that uses a smartphone to visualize the fluorescence image of biological samples. Our fluorescence microscope uses a laser-based simplified optical filter system, that provides analog optical filtering capabilities of a fluorescence filter cube. Firstly, we validated our inverted optical filtering by visualizing microbeads labeled with three different fluorescent compounds or fluorophores, commonly used for disease diagnosis. Secondly, we validated the disease diagnosis capabilities, by comparing the results of our device with those of a commercial fluorescence microscope. We successfully detected and visualized Trypanosoma cruzi parasites, responsible of the Chagas infectious disease, and the presence of Antineutrophil cytoplasmic antibodies of the ANCA non-communicable autoimmune disease. The samples were labeled with the fluorescein isothiocyanate (FITC) fluorophore, one of the most commonly used for disease diagnosis. Our device provides a 400 X magnification and is at least two orders magnitude cheaper than conventional commercial fluorescence microscopes.

The Coronavirus disease 2019 (COVID-19) rapidly spread to over 180 countries and abruptly disrupted the production rates and supply chains worldwide. Since then, 3D printing also recognized as additive manufacturing (AM) and known to be a novel technique that uses layer-by-layer deposition of material to produce the intricate 3D geometry, has been engaged in reducing the distress caused by the outbreak. During the early stages of this pandemic, shortages of Personal Protection Equipment (PPE), including facemasks, shields, respirators, and other medical gears, were significantly answered by remotely 3D printing them. Amidst the growing testing requirements, the 3D printing emerged as a potential and fast solution manufacturing process to meet the production needs due to its flexibility, reliability, and rapid response capabilities. In the recent past, some of the other medical applications that have gained prominence in the scientific community include 3D printed ventilator splitters, device components, and patient-specific products. Regarding the non-medical applications, researchers have successfully developed contact-free devices to address the sanitary crisis in public places. This work aims to systematically review the applications of 3D printing or AM techniques that have been involved in producing various critical products essential to limit this deadly pandemic's progression.

Cancer invasion through basement membranes represents the initial step of tumor dissemination and metastasis. However, little is known about how human cancer cells breach basement membranes. Here, we used a 3-dimensional in vitro invasion model consisting of cancer spheroids encapsulated by a basement membrane and embedded in 3D collagen gels to visualize the early events of cancer invasion by confocal microscopy and live-cell imaging. Human breast cancer cells generated large numbers of basement membrane perforations, or holes, of varying sizes that expanded over time during cell invasion. We used a wide variety of small molecule inhibitors to probe the mechanisms of basement membrane perforation and hole expansion. Protease inhibitor treatment (BB94), led to a 63% decrease in perforation size. After myosin II inhibition (blebbistatin), basement membrane perforation area decreased by only 15%. These treatments produced correspondingly decreased cellular breaching events. Interestingly, inhibition of actin polymerization dramatically decreased basement membrane perforation by 80% and blocked invasion. Our findings suggest that human cancer cells can primarily use proteolysis and actin polymerization to perforate the BM and to expand perforations for basement membrane breaching, with a relatively small contribution from myosin II contractility.

The cuttlebone-like structure is a complex porous bionic structure with asymmetric sinusoidal S-shaped wall structure connecting laminar septa, and studies have shown that the cuttlebone-like structure has light weight, high strength and excellent energy absorption capability. It has become an important research to investigate the mechanical mechanism of cuttlebone-like structure and to design a bionic structure beyond nature structure based on it. In order to investigate the mechanical properties of the static compression and shearing processes of the cuttlebone-like structure, this paper establishes theoretical formulas and analyzes the influence of dimensionless parameters such as height-to-thickness ratio $\lambda$, period-to-thickness ratio $\xi$ and amplitude to period ratio $\eta$ on the compression and shearing processes with the help of ABAQUS finite element software.The parameter sensitivity analysis method was used to compare the important influence degree of each dimensionless parameter on the mechanical properties of the structure and to determine the relative optimal parameters of the structural mechanical properties under compression and shearing. Based on the relatively optimal parameter of the cuttlebone-like structure, the cross-sectional geometry of the structure is improved to build a new cuttlebone-like structure.The experimental results showed that the new cuttlebone-like structure with revised cross-section improved the mechanical properties of the cuttlebone-like structure.The study results are of theoretical guidance to enhance the mechanical properties and geometric design of cuttlebone-like structures.

Despite all their advantages, load-bearing concrete shell structures with double curvatures are not frequently in use. The main reason is the complexity of their construction. In such a context, this article starts with a brief, critical review of existing technologies while their pros and cons are highlighted. Against that background the authors then propose a new approach for the highly automated fabrication of gridshell structures from variable modules. To demonstrate the feasibility of such a new technology, a demonstrator called ConDIT 1.0, a sphere-like shell structure composed of several frames was designed and built. The frame modules were fabricated automatically using extrusion-based 3D printing and a printable, strain-hardening cement-based composite (SHCC). This article presents the design of ConDIT 1.0, the mechanical material characterization of printed SHCC, the technology of module production, the results of geometry verification for print modules using 3D scanning, and the procedure for the demonstrator’s assembly.

This paper is part of a study of earthen mixtures for 3D printing of buildings. To meet the ever-growing environmental needs, the focus of the paper is on a particular type of biocomposite for the stabilization of earthen mixtures—the rice husk-lime biocomposite—and on how to enhance its effect on the long-term mechanical properties of the hardened product. Having assumed that the shredding of the vegetable fiber is precisely one of the possible ways to improve the mechanical properties, we compared the results of uniaxial compression tests performed on cubic specimens made with both shredded and unaltered vegetable fiber, for three curing periods. The results showed that the hardened earthen mixture is not a brittle material in the strict sense, because it exhibits some peculiar behaviors, anomalous for a brittle material. However, being a “designable” material, its properties can be varied with a certain flexibility to get as close as possible to the desired ones. One of the peculiar properties of the hardened earthen mixture deserves further investigation, rather than corrections. This is the vulcanization that occurs (in a completely natural way) in the long term, thanks to the mineralization of the vegetable fiber by carbonation of the lime.

The process of full-thickness skin regeneration is complex and has many parameters involved, which makes it difficult to use a single dressing to meet the various requirements of the complete regeneration at the same time. Therefore, developing hydrogel dressings with multifunction, including tunable rheological properties and aperture, hemostatic, antibacterial and super cytocompatibility, is a desirable candidate in wound healing. In this study, a series of complex hydrogels were developed via the hydrogen bond and covalent bond between chitosan (CS) and alginate (SA). These hydrogels exhibited suitable pore size and tunable rheological properties for cell adhesion. Chitosan endowed hemostatic, antibacterial properties and great cytocompatibility and thus solved two primary problems in the early stage of the wound healing process. Moreover, the sustained cytocompatibility of the hydrogels was further investigated after adding FGF and VE-cadherin via the co-culture of L929 and EC for 12 days. The confocal 3D fluorescent images showed that the cells were spherical and tended to form multicellular spheroids, which distributed in about 40-60μm thick hydrogels. Furthermore, the hydrogel dressings significantly accelerate defected skin turn to normal skin with proper epithelial thickness and new blood vessels and hair follicles through the histological analysis of in vivo wound healing. The findings mentioned above demonstrated that the CS/SA hydrogels with growth factors have tremendous potential as multifunctional hydrogel dressings for full-thickness skin regeneration incorporated with hemostatic, antibacterial, sustained cytocompatibility for 3D cell culture and normal skin repairing.

Aim of this research paper is to introduce a novel method of hybrid orthodontic tooth-borne distalizer treatment of class II malocclusion by using 3D printed biocompatible personalized distalizer. Explains 3D designing, printing and clinical application of individualized biocompatible medical device dedicated for orthodontic teeth distalization. Compares such distalizer manufactured from two different biocompatible photopolymers (white and transparent). Evaluates their clinical performance and also patients’ aesthetical perception. Clinical part includes comparison of treatment debonding on the set of 12 complete orthodontic treatments with uni-lateral class II malocclusion managed with hybrid approach (CAT-Invisalign with 3D printed distalizer). Paper offers an evaluation of the personalized distalizer functioning in regard to current publications and comparison to conventional prefabricated alternatives like Carriere® Distalizer™ appliance. Results showed no significance of material differences on clinical performance of such individualized distalizers. Research showed preference of patients towards transparent biocompatible photopolymer instead of white A2 shade.

Parts produced by laser or electron-beam powder bed fusion (PBF) additive manufacturing are prone to residual stresses, deformations, and other defects linked to non-uniform temperature distribution during the manufacturing process. Several researchers have highlighted the important role scan sequence plays in achieving uniform temperature distribution in PBF. However, scan sequence continues to be determined offline based on trial-and-error or heuristics, which are neither optimal nor generalizable. To address these weaknesses, we have articulated a vision for an intelligent online scan sequence optimization approach to achieve uniform temperature distribution, hence reduced residual stresses and deformations, in PBF using physics-based and data-driven thermal models. This paper proposes SmartScan, our first attempt towards achieving our vision using a simplified physics-based thermal model. The conduction and convection dynamics of a single layer of the PBF process are modeled using the finite difference method and radial basis functions. Using the model, the next best feature (e.g., stripe or island) that minimizes a thermal uniformity metric is found using control theory. Simulations and experiments involving laser marking of a stainless steel plate are used to demonstrate the effectiveness of SmartScan in comparison to existing heuristic scan sequences for stripe and island scan patterns. In experiments, SmartScan yields up to 43% improvement in average thermal uniformity and 47% reduction in deformations (i.e., warpage) compared to existing heuristic approaches. It is also shown to be robust, and computationally efficient enough for online implementation.

The powder bed fusion (PBF) metal additive manufacturing (AM) method uses an energy source like a laser to melt the metal powders. The laser can locally melt the metal powders and creates a solid structure as it moves. The complexity of the heat distribution in laser PBF metal AM is one of the main features that need to be accurately addressed and understood to design and manage an optimized printing process. In this research, the dependency of local thermal rates and gradients on print after solidification (in the heat-affected zone) was numerically simulated and studied to provide information for designing the print process. The simulation results were validated by independent experimental results. The simulation shows that the local thermal rates are higher at higher laser power and scan speed. Also, the local thermal gradients increase if the laser power increases. The effect of scan speed on the thermal gradients is opposite during heating versus cooling times. Increasing the scan speed increases the local thermal gradients in the cooling times and decreases the local thermal gradients during the heating. In addition, these simulation results could be used in artificial intelligence (AI) and machine learning for developing digital additive manufacturing.

Fatigue analysis plays a vital role in determining the structural integrity and life of a dental implant. With the use of such implants on the rise, there is a corresponding increase in the number of implant failures. As such, the aim of this research paper is to investigate the life of 3D-printed dental implants. The dental implants considered in this study were 3D printed according to the direct metal laser sintering (DMLS) method. Additionally, a finite element model was developed to study their performance, while fatigue life was predicted using Fe-Safe software®. The model was validated experimentally by performing fatigue tests. The life of the dental implants was analysed based on Normal strain and the Brown-Miller with Morrow mean correction factor algorithm. The model revealed that there was a strong correlation between the FEA and the experimental results. The clinical success of 3D-printed dental implant experimentally is 20.51 years and computationally under Normal strain is 19.89 years and Brown-Miller with Morrow mean correction factor is 26.82 years.

Human populations and natural ecosystems are bound to be exposed to ionizing radiation1from the deposition of artificial radionuclides resulting from nuclear accidents, nuclear devices2or radiological dispersive devices ("dirty bombs"). On the other hand, NORM industries such as3phosphate production or uranium mining, contribute to the on site storage of residuals with enhanced4concentrations of natural radionuclides. Therefore, in the context of the European agreements5concerning nuclear energy, namely the EURATOM (European Atomic Energy Community) Treaty,6monitoring is an essential feature of the environmental radiological surveillance. In this work, we7obtain 3D maps from outdoor scenarios, and complete such maps with measured radiation levels8and with its radionuclide signature. In such scenarios, we face challenges such as unknown and9rough terrain, limited number of sampled locations and the need for different sensors and therefore10different tasks. We propose a radiological solution for scouting, monitoring and inspecting an area of11interest, using a fleet of drones and a controlling ground station. First, we scout an area with a LiDAR12onboard a drone to accurately 3D-map the area. Then, we monitor that area with a Geiger-Muller13sensor at a low-vertical distance from the ground to produce a radiological (heat)map that is overlaid14on the 3D map of the scenario. Next, we identify the hotspots of radiation, and inspect them in detail15using a drone by landing on them, to reveal its radionuclide signature using a CZT sensor. We present16the algorithms used to implement such tasks both at the ground station and on the drones. The three17mission phases were validated using actual experiments in three different outdoor scenarios. We18conclude that drones can not only perform the mission efficiently, but in general they are faster and19as reliable as personnel on the ground

We investigated the properties of architected materials made from UV-cured urethane elastomers and the use of such materials for insoles. The durability and reliability of various materials currently used in medical insoles were compared with those of architected materials with microlattice. The results show that architected materials made from UV-cured urethane elastomers have high impact resilience and grip, and the hardness can easily be changed by adjusting the column diameter of the unit cell. Compared with the foam materials used for medical insoles today, these architected materials also demonstrate superior UV resistance, suggesting that, after being washed in water, they can be air-dried outdoors.

The urgent need to improve performance in the construction industry has led to the adoption of many innovative technologies. 3D laser scanners are amongst the leading technologies being used to capture and process assets or construction project data for use in various applications. Due to its nascent nature, many questions are still unanswered about 3D laser scanning, which in turn contribute to the slow adaptation of the technology. Some of these include the role of 3D laser scanners in capturing and processing raw construction project data. How accurate is the 3D laser scanner or point cloud data? How does laser scanning fit with other wider emerging technologies such as Building Information Modelling (BIM)? This study adopts a proof-of-concept approach, which in addition to answering the afore-mentioned questions, illustrates the application of the technology in practice. The study finds that the quality of the data, commonly referred to as point cloud data is still a major issue as it depends on the distance between the target object and 3D laser scanner’s station. Additionally, the quality of the data is still very dependent on data file sizes and the computational power of the processing machine. Lastly, the connection between laser scanning and BIM approaches is still weak as what can be done with a point cloud data model in a BIM environment is still very limited. The aforementioned findings reinforce existing views on the use of 3D laser scanners in capturing and processing construction project data.

Innovations in engineering education are undergoing a noticeable transformation. Higher education institutions are practicing distance education, remote laboratories, studio pedagogies and several other approaches in order to increase their students’ retention, success, and preparedness for the job market. In engineering education, maker spaces have become popular in the last ten years in universities as well as community colleges, high-schools and community innovation hubs. A large number of engineering colleges have allocated significant spaces, and at some universities entire buildings as maker spaces to be used for curricular and extracurricular activities. Success stories of these types of spaces are well documented. This paper describes the activities and programs held at Tennessee Tech University’s maker space called ‘iMakerSpace.’ These accomplishments include several workforce development activities. The impact and effectiveness of the iMakerSpace is evaluated through analysis of survey data.

The growth of solid particles during liquid phase sintering was modeled by the Cellular Automata method. The binary phase diagram and Fickian approach for the diffusion process were applied to simulate the chemical composition variation in liquid and solid phases during sintering. The Oswald-Ripening effect was considered during the dissolution of the solid phase in the liquid phase. It is used to define the probability of solid-phase dissolution by the liquid phase and develop the model to simulate the alloy with solid solubility. So, the microstructure could be modeled in the liquid phase sintering process.

Cardiovascular-related diseases are one of the leading causes of death worldwide. An understanding of heart movement based on images plays a vital role in assisting the procedure in the postoperative and postoperative processes. In particular, if the shape information can be provided in real-time using the electrocardiogram(ECG) signal using this information, the heart’s movement information can be used for cardiovascular analysis and imaging guides during surgery. In this paper, we propose creating a 3D+t cardiac coronary artery model that is rendered in real-time according to the ECG signal. Hierarchical cage-based deformation modeling is used to generate mesh deformation used during the procedure according to the ECG signal. We match the blood vessel’s lumen obtained from the ECG-gated 3D+t CT angiography taken at the multiple cardiac phases to derive the optimal deformation. Splines for 3D deformation control points were used to continuously represent the obtained deformation at the multi-view according to the ECG signal. To verify the proposed method, we compared the manually segmented lumen and results of the proposed method for eight patients. The average distance and dice coefficient between the two models was 0.543mm and 0.735, respectively. The required time for registration of the 3D coronary artery model is 23.53 seconds/model. rendering speed to derive the model according to the ECG signal after generating the 3D+t model is faster than 120 FPS.

This paper aims to implement histogram pyramids with marching cubes method for 3D medical volumetric rendering. The histogram pyramids are used for feature extraction by segmenting the image into the hierarchical order like the pyramid shape. The histogram pyramids can decrease the number of sparse matrixes that will occur during voxel manipulation. The important feature of the histogram pyramids is the direction of segments in the image. This feature will be then used for connecting pixels (2D) to form up voxel (3D) during marching cubes implementation. The proposed method is fast and easy to implement and it also produces a smooth result (compared to the traditional marching cubes technique). The experimental results show that time consuming for generating 3D model can be reduced by 15.59% in average. The paper also shows the comparison between the surface rendering using the traditional marching cubes and the marching cubes with histogram pyramids. Therefore, for the volumetric rendering such as 3D medical models and terrains where a large number of lookups in 3D grids are performed, this method is a particularly good choice for generating the smooth surface of 3D object.

The COVID-19 crisis has resulted in a shortage of personal protective equipment (PPE) [1]. COVID-19 is currently the leading cause of death in the United States[2]. Health care providers caring for COVID-19 patients or at high risk of being exposed to the SARS-CoV-2 virus benefit from a face shield to protect against aerosol droplets that could hit the face and minimize the chance of inadvertently touching the face with contaminated hands, and air filtration to filter out aerosolized SARS-CoV-2. Adapting commercially available full-faced snorkel masks has been proposed as an alternative to narrow the gap in PPE [3]. Here we explore a full-faced snorkel mask with commercially available particulate filters.

This study proposes a novel flexible bus dispatching system where a fleet of fully automated modular bus units, together with conventional buses, serves the passenger demand. These modular bus units can either operate individually or combined (forming larger modular buses with a higher passenger capacity). This provides enormous flexibility to manage the service frequencies and vehicle allocation, reducing thereby the operating cost and improving passenger mobility. We develop an optimization model used to determine the optimal composition of bus units and the optimal service frequency at which the buses (both conventional and modular) are dispatched across each bus line. We explicitly account for the dynamics of traffic congestion and complex interactions between the modes at the network level based on the recently proposed three-dimensional macroscopic fundamental diagram (3D-MFD). To the best of our knowledge, this is the first application of the 3D-MFD and modular bus units for the frequency setting problem in the domain of bus operations. Numerical results show the improvements in the total system cost made by adapting the number of combined modular bus units and their dispatched frequencies to the evolution of both, the car and the passenger demand. A comparison with the commonly used approach that considers only the bus system (neglecting the complex multimodal interactions and congestion propagation) reveals the value of the proposed modeling framework.

In this experimental report the biocompatibility of elastomeric scaffold structures made via stereolithography employing table-top 3D printer (Ember, Autodesk) and commercial resin FormLabs Flexible (FormLabs) was studied. The samples were manufactured using standard printing and development protocol, which is known to inherit cytotoxicity due to remaining non-polymerized remaining monomers, despite the polymerized material being fully biocompatible. Additional steps were taken to remedy this problem: the fabricated structures were soaked in isopropanol and methanol for different conditions (temperature, duration) in order to leach out the non-polymerized monomers. Also printed structures were UV exposed to assure maximum polymerization degree of the material. Post-processed structures were seeded with myogenic stem cells and the number of live cells was evaluated as an indicator for the material biocompatibility. The straightforward post-processing protocol enhances the biocompatibility by 7 times after 7 days soaking in isopropanol and methanol and is comparable to control (glass and polystyrene) samples. This proposes the approach as a novel and simple method to be widely applicable for dramatic cytotoxicity reduction of optically 3D printed micro-/nano-scaffolds for biomedical applications.

A fast calculation method for the full parallax high-resolution hologram is proposed based on the elemental light field image (EI) rendering. A 3D object located near the holographic plane is firstly rendered as multiple EIs with a pinhole array. Each EI is interpolated and multiplied by a divergent sphere wave and interfered with a reference wave to form a hogel. Parallel acceleration is used to calculate the high-resolution hologram because calculation of each hogel is independent. A high-resolution hologram with the resolution of 20,0000×20,0000 pixels is calculated only within 8 minutes. Full parallax high-resolution 3D displays are realized by optical reconstructions.

The aim of this study is to provide a detailed strategy for Safe-by-Design (SbD) 3D printed lab-on-a-chip (LOC) device manufacturing, using Fused Filament Fabrication (FFF) technology. At first, the applicability of FFF in lab-on-a-chip device development is briefly discussed. Subsequently, a methodology to categorize, identify and implement SbD measures for FFF is suggested. Furthermore, the most crucial health risks involved in FFF processes are examined, placing the focus on the examination of ultrafine particle (UFP) and Volatile Organic Compound (VOC) emission hazards. Thus, a SbD scheme for lab-on-a-chip manufacturing is provided, while also taking into account process optimization for obtaining satisfactory printed LOC quality. This work can serve as a guideline for the effective application of FFF technology for lab-on-a-chip manufacturing through the safest applicable way, towards a continuous effort to support sustainable development of lab-on-a-chip devices through cost-effective means.

Resistance to hormone therapy and disease progression is the major challenge in clinical management of prostate cancer (PC). Drugs currently used in PC therapy initially show a potent antitumor effect. Nevertheless, PC gradually develops resistance, relapses and spreads. Most patients develop, indeed, castrate-resistant PC (CRPC), which is almost incurable. The nerve growth factor (NGF) acts on a variety of non-neuronal cells by activating the NGF tyrosine-kinase receptor, TrkA. NGF signaling is deregulated in PC. In androgen-dependent PC cells, TrkA mediates the proliferative action of NGF through its cross talk with the androgen receptor (AR). Epithelial PC cells, however, acquire the ability to express NGF and TrkA, as the disease progresses, indicating a role for NGF/TrkA axis in PC progression and androgen-resistance. We here report that once activated by NGF, TrkA mediates proliferation, invasiveness and epithelial-mesenchyme transition (EMT) in various CRPC cells. NGF promotes organoid growth in 3D models of CRPC cells, and specific inhibition of TrkA impairs all these responses. Thus TrkA represents a new biomarker to target in CRPC.

3D object reconstruction from depth image streams using Kinect-style depth cameras has been extensively studied. In this paper, we propose an approach for accurate camera tracking and volumetric dense surface reconstruction assuming a known cuboid reference object is present in the scene. Our contribu¬tion is three-fold. (a) We maintain drift-free camera pose tracking by incorporating the 3D geometric constraints of the cuboid reference object into the image registration process. (b) We reformulate the problem of depth stream fusion as a binary classification problem, enabling high-fidelity surface reconstruction, especially in the con¬cave zones of objects. (c) We further present a surface denoising strategy to mitigate the topological inconsistency (e.g., holes and dangling triangles), which facilitates the generation of a noise-free triangle mesh. We extend our public dataset CU3D with several new image sequences, test our algorithm on these sequences and quantitatively compare them with other state-of-the-art algorithms. Both our dataset and our algorithm are available as open-source content at https://github.com/zhangxaochen/CuFusion for oth-er researchers to reproduce and verify our results.

The increased consumption of food requiring thermoformed packaging means that the packaging industry demands customized solutions in terms of shapes and sizes to make the packaging unique. In particular, the food industry increasingly requires more transparent packaging, with greater clarity and a better presentation of the product features they contain. However, in turn, the differentiation of products is sought through the geometry and final finish of the product, as well as the arrangement of food inside the packaging. In addition, these types of packaging usually include ribs in the walls to improve physical properties, however they also affect the final aesthetics of the product. In accordance with this, this research study analyses by studying the mechanical properties of different relief geometries that can affect not only the aesthetics but also their strength. For this purpose, tensile and compression tests have been carried out. The results provide comparative data on the reliefs studied and show that there are different shapes, sizes and layout.

Fast 3D reconstruction with semantic information on road scenes is of great requirements for autonomous navigation. It involves issues of geometry and appearance in the field of computer vision. In this work, we propose a method of fast 3D semantic mapping based on the monocular vision. At present, due to the inexpensive price and easy installation, monocular cameras are widely equipped on recent vehicles for the advanced driver assistance and it is possible to acquire semantic information and 3D map. The monocular visual sequence is used to estimate the camera pose, calculate the depth, predict the semantic segmentation, and finally realize the 3D semantic mapping by combination of the techniques of localization, mapping and scene parsing. Our method recovers the 3D semantic mapping by incrementally transferring 2D semantic information to 3D point cloud. And a global optimization is explored to improve the accuracy of the semantic mapping in light of the spatial consistency. In our framework, there is no need to make semantic inference on each frame of the sequence, since the mesh data with semantic information is corresponding to sparse reference frames. It saves amounts of the computational cost and allows our mapping system to perform online. We evaluate the system on naturalistic road scenes, e.g., KITTI and observe a significant speed-up in the inference stage by labeling on the mesh.

The possibility of using additive manufacturing (AM) in the medicine area has created a new opportunities in health care. This has contributed to a sharp increase in demand for 3D printers, their systems and materials that are adapted to strict medical requirements. We described herein a medical-grade thermoplastic polyurethane (S-TPU), which was developed and then formed into a filament for Fused Deposition Modeling (FDM) 3D printers during a melt-extrusion process. S-TPU consisting of aliphatic hexamethylene 1,6-diisocyanate (HDI), amorphous α,ω-dihydroxy(ethylene-butylene adipate) (PEBA) and 1,4 butandiol (BDO) as a chain extender, was synthesized without the use of a catalyst. The filament properties were characterized by rheological, mechanical, physico-chemical and in vitro biological properties. The tests showed biocompatibility of the obtained filament as well as revealed no significant effect of the filament formation process on its properties. This study may contribute to expanding the range of medical-grade flexible filaments for standard low-budget FDM printers.

Molecular detection of pathogens in clinical samples often requires pretreatment techniques, including immunomagnetic separation and magnetic silica bead (MSB)-based DNA purification to obtain the purified DNA of pathogens. These two techniques usually rely on handling small tubes containing a few millilitres of the sample and manual operation, implying that an automated system encompassing both techniques is needed for larger quantities of the samples. Here, we report a 3D-printed microfluidic platform that enables bacterial preconcentration and genomic DNA (gDNA) purification for improving the molecular detection of target pathogens in blood samples. The device consists of two microchannels and one chamber, which can be used to preconcentrate pathogens bound to antibody-conjugated magnetic nanoparticles (Ab-MNPs) and subsequently extract gDNA using magnetic silica beads (MSBs) in a sequential manner. The device was able to preconcentrate very low concentrations of pathogens and extract their genomic DNA in 10 mL of 10% blood within 30 min, and thus allowed polymerase chain reaction (PCR) and quantitative PCR to detect 1 colony forming unit of Escherichia coli O157:H7 in 10% blood. The results suggest that the 3D-printed microfluidic platform is highly useful for lowering the limitations on molecular detection in blood by preconcentrating the target pathogen and isolating its DNA in a large volume of the sample.

The dopamine D3 receptor is an important CNS target for the treatment of a variety of neurological diseases. Selective dopamine D3 receptor antagonists modulate the improvement of psychostimulant addiction and relapse. In this study, five and six featured pharmacophore models of D3R antagonists were generated and evaluated with the post-hoc score combining two survival scores of active and inactive. Among Top 10 models, APRRR215 and AHPRRR104 were chosen based on the coefficient of determination (APRRR215: R2training = 0.80; AHPRRR104: R2training = 0.82) and predictability (APRRR215: Q2test = 0.73, R2predictive = 0.82; AHPRRR104: Q2test = 0.86, R2predictive = 0.74) of their 3D-quantitative structure–activity relationship models. Pharmacophore-based virtual screening of a large compound library from eMolecules (> 3 million compounds) using two optimal models expedited the search process 100-fold speed increase compared to the docking-based screening (HTVS scoring function in Glide) and identified a series of hit compounds having promising novel scaffolds. After the screening, docking scores, as an adjuvant predictor, were added to two fitness scores (from the pharmacophore models) and predicted Ki (from PLSs of the QSAR models) to improve accuracy. Final selection of the most promising hit compounds were also evaluated for CNS-like properties as well as expected D3R antagonism.

Recent advances in sensor and platform technologies such as satellite systems, unmanned aerial vehicles (UAV), manned aerial platforms, and ground-based sensor networks have resulted in massive volumes of data is produced and collected about the earth. Processing, managing, and analyzing these data is one of the main challenges in 3D synthetic representation used in modeling and simulation (M&S) of the natural environment. M&S devices, such as flight simulators, traditionally require a variety of different databases to provide a synthetic representation of the world. M&S often requires integration of data from a variety of sources stored in different formats. Thus, for simulation of a complex synthetic environment, such as a 3D terrain model, tackling interoperability among its components (geospatial data, natural and man-made objects, dynamic and static models) is a critical challenge. Conventional approaches used local proprietary data models and formats. These approaches often lacked interoperability and created silos of content within the simulation community. Therefore, open geospatial standards are increasingly perceived as a means to promote interoperability and reusability for 3D M&S. In this paper, the Open Geospatial Consortium (OGC) CDB Standard is introduced. “CDB” originally refers to Common DataBase which is currently considered as a name with no abbreviation in the OGC community. The OGC CDB is an international standard for structuring, modeling, and storing geospatial information required in high performance modeling and simulation applications. CDB defines the core conceptual models, use cases, requirements, and specifications for employing geospatial data in 3D M&S. The main features of the OGC CDB Standard are described as run-time performance, full plug-and-play interoperable geospatial data store, usefulness in 3D and dynamic simulation environment, ability to integrate proprietary and open-source data formats. Furthermore, compatibility with the OGC standards baseline reduces the complexity of discovering, transforming, and streaming geospatial data into the synthetic environment and makes them more widely acceptable to major geospatial data/software producers. This paper includes an overview of OGC CDB version 1.0 which defines a conceptual model and file structure for the storage, access, and modification of a multi-resolution 3D synthetic environment data store. Finally, this paper presents a perspective of future versions of the OGC CDB and what the steps are for humanizing the OGC CDB standard with the other OGC/ISO standards baseline.

There is a growing interest in fibers supporting optoelectrical properties for textile and wearable display applications. Solution-processed electroluminescent (EL) material systems can be continuously deposited onto fiber or yarn substrates in a roll-to-roll process, making it easy to scale manufacturing. It is important to have precise control over layer deposition to achieve uniform and reliable light emission from these EL fibers. Slot-die coating offers this control and increases the rate of EL fiber production. Here, we report a highly adaptable, cost-effective 3D printing model for developing slot dies used in automatic coating systems. The resulting slot-die coating system enables rapid, reliable production of alternating current powder-based EL (ACPEL) fibers and can be adapted for many material systems. The benefits of this system over dip-coating for roll-to-roll production of EL fibers are demonstrated in this work.

For multi-sensor integrated systems, such as a mobile mapping system (MMS), data fusion at sensor-level, i.e., the 2D-3D registration between optical camera and LiDAR, is a prerequisite for higher level fusion and further applications. This paper proposes a line-based registration method for panoramic images and LiDAR point cloud collected by a MMS. We first introduce the system configuration and specification, including the coordinate systems of the MMS, the 3D LiDAR scanners, and the two panoramic camera models. We then establish the line-based transformation model for panoramic camera. Finally, the proposed registration method is evaluated for two types of camera models by visual inspection and quantitative comparison. The results demonstrate that the line-based registration method can significantly improve the alignment of the panoramic image and LiDAR datasets under either the ideal spherical or the rigorous panoramic camera model, though the latter is more reliable.

Purpose: Only two studies have examined the second-order false belief mentalizing ability of people with Williams syndrome (WS). The exact age in one study that successfully passed the advanced complex mentalizing ability exceeded nine years in chronological age. Another study reported failure to pass second-order false-belief tasks among people with WS at an averagely of 8.56 years in their mental age. This study aimed to examine the nature of the second-order mentalizing ability of people with WS using computerized animations to investigate the possibility of rehabilitation. Methods: Advanced technology of three-dimensional (3D) animation clips was used as an experimental tool. People with WS viewed clips in a quiet room without interruption. After watching each clip, people with WS answered the following questions: character recognition, reality, memory, and second-order false beliefs. Responses from people with WS were recorded and analyzed. Results: The mental passing age of the second-order false-belief task in people with WS in the current study was 7.14 years. People with WS improved their mentalizing ability to the advanced, complex mental states of other people using computerized animation clips. People with WS performed better with 3D animation stimuli than with traditional two-dimensional (2D) stimuli. Conclusion: With 3D animation clips, people with neurodevelopmental disabilities can induce second-order false belief mentalizing abilities, as shown in people with WS.

Reconstructing 3D indoor scenes from 2D images has always been an important task in computer vision and graphics applications. For indoor scenes, traditional 3D reconstruction methods suffer from the lack of surface details, poor reconstruction of large flat surface textures and areas with uneven lighting, and many falsely reconstructed floating debris noises in the reconstructed models. We add adaptive normal priors to the neural implicit reconstruction process to optimize the network, and improve the accuracy of volume density prediction by adding regularization terms to the neural radiation field to constrain the volume density obtained by weight distribution, and learn a smooth SDF surface from the network to obtain an explicit mesh model. Experiments show that the method proposed in this paper outperforms the state-of-the-art methods on ScanNet, Hypersim, and Replica datasets.

This study presents a novel approach combining computer vision with topology optimization for additive manufacturing. Using specialized photogrammetry software, we capture high-resolution images of the design domain to create precise 3D models through detailed scanning. These models are converted into STL file format and remeshed using an adaptive algorithm within COMSOL 5.3 Multiphysics, managed by a custom MATLAB 2023. This integration allows optimal mesh resolution and accuracy in analyses. We applied this method to design a concrete pillar for 3D printing, aiming for a 75% volume reduction to enhance material efficiency and stability, crucial for extraterrestrial environments. The design, scanned with a 360-degree camera array, informed the MATLAB-based topology optimization process. Combining MATLAB’s optimization algorithms with COMSOL’s meshing and finite element solver solver, we explored material-efficient configurations. The results show significant volume reduction, particularly in the central design area, optimizing material use while maintaining structural stability. The optimization algorithm demonstrated rapid, stable convergence to near-optimal solutions within about 20 iterations, highlighting the method’s efficiency and robustness in complex design optimization.

Gravity forward modeling as a basic tool has been wildly used to topography correction and 3D density inversion. The source region is usually discretized into tesseroid (i.e., spherical prism) to consider the influence of the curvature of planets in global or large-scale problems. Traditional gravity forward modeling methods in spherical coordinates, including the Taylor expansion and Gaussian-Legendre quadrature, are all based on spatial domain, which are mostly low computational efficiency. This study proposes a high-efficient forward modeling method of gravitational fields in spherical harmonic domain, in which the gravity anomalies and gradient tensors can be expressed as spherical harmonic synthesis form of spherical harmonic coefficients of 3D density distribution. A homogeneous spherical shell model has been used to test its effectiveness compared with traditional spatial domain methods. It demonstrates that the computational efficiency of the proposed spherical harmonic domain method has improved by four orders of magnitude and with a similar level of computational accuracy compared with the optimized 3D GLQ method. Finally, the proposed forward method is applied to topography correction of the Moon. The results show that the gravity response of the topography by our method is close to that of the optimized 3D GLQ method, and is also consistent with previous results.

The dynamic landscape of 3D printing has experienced a notable surge in the development of diverse filaments tailored for a wide range of applications in medicine. This experimental study thoroughly examines the mechanical properties of nine popular 3D printer filaments, namely PLA, ABS, HIPS, PETG, PA, Carbon Fiber, Ceramic, PMMA, and Metal composite. Focusing on key aspects such as tensile strength and compressive tests, the study delves into the intricate mechanical characteristics of these 3D printer filaments. In addition to the mechanical properties, the study provides a comprehensive exploration of essential filament attributes, including melting point, bed temperature requirements, and density of nine different filament properties. Furthermore, the study addresses crucial considerations in material selection for different applications. Through insightful comparisons, the article illuminates the advantages and limitations of various available filaments within the realm of applications. This study serves as a valuable resource, offering nuanced insights for researchers, engineers, and medical professionals seeking a deeper understanding of the mechanical characteristics of 3D printer filaments and their potential applications.

Laser powder bed fusion (LPBF) is an additive manufacturing technique that is gaining popularity for producing metallic parts in various industries. However, parts produced by LPBF are prone to residual stress, deformation, cracks and other quality defects due to uneven temperature distribution during the LPBF process. To address this issue, in prior work, the authors have proposed SmartScan, a method for determining laser scan sequence in LPBF using an intelligent (i.e., model-based and optimization-driven) approach, rather than using heuristics, and applied it to simple 2D geometries. This paper presents a generalized SmartScan methodology that is applicable to arbitrary 3D geometries. This is achieved by: (1) expanding the thermal model and optimization approach used in SmartScan to multiple layers; (2) enabling SmartScan to process shapes with arbitrary contours and infill patterns within each layer; (3) providing the optimization in SmartScan with a balance of exploration and exploitation to make it less myopic; and (4) improving SmartScan's computational efficiency via model order reduction using singular value decomposition. Sample 3D test artifacts are simulated and printed using SmartScan in comparison with common heuristic scan sequences. Reductions of up to 92% in temperature inhomogeneity, 86% in residual stress, 24% in maximum deformation and 50% in geometric inaccuracy were observed using SmartScan, without significantly sacrificing print speed. An approach for using SmartScan for printing complex 3D parts in practice, by integrating it as a plug-in to a commercial slicing software, was also demonstrated experimentally, along with its benefits in significantly improving printed part quality.

Traditional 3D reconstruction models have consistently encountered a challenge: attaining high recall of object edges while preserving precision. In this paper, we introduce a post-processing method Multi-Head Attention Refiner (MA-R) aimed at tackling this challenge by integrating a multi-head attention mechanism within the U-Net style refiner module. The 3D reconstruction model applying this method demonstrates excellence in parsing intricate image details, resulting in significant enhancement of boundary predictions and increased recall rates. In our experiments, our method significantly enhances the reconstruction performance of Pix2Vox++ when multiple images are utilized as input. Specifically, it achieves an enhanced Intersection Over Union score of approximately 1.1% compared to the original Pix2Vox++ model when 16-view images are employed.

3D reality capturing has demonstrated increased efficiency and consistently accurate outcomes in architectural digitisation. Nevertheless, despite advancements in data collecting, 3D reality capturing still lacks full automation, especially in the post-processing and modelling phase. Artificial intelligence (AI) has been a significant focus, especially in computer vision, and tasks such as image classification and object recognition might be beneficial to the digitisation process and its subsequent utilisation. This article aims to examine the potential outcomes of integrating AI technology into the field of 3D reality-capturing, with a particular focus on its use in architectural scenarios. The main methods used for data collection are laser scanning (static or mobile) and photogrammetry. As a result, image data including RGB-D data (files containing both RGB colours and Depth information) and point clouds have become the most common raw datasets available for object mapping. The study comprehensively analyses the current use of 2D and 3D deep learning techniques in documentation tasks, particularly downstream applications. It also highlights the ongoing research efforts in developing real-time applications with the ultimate objective of achieving generalisation and improved accuracy.

Jump rope is a widely-applied basic training in various sports, yet it is understudied biomechanically. This study investigates the impact of cycle-tempo-induced motor control changes in elite jump rope athletes, addressing the biomechanical gap of cyclic skill control. The hypothesis posited two accelerations per jump cycle—one in front of and one behind the body—and anticipated that increased cycle frequency would alter the distribution of acceleration time within a cycle. Using 3D motion analysis, kinematic parameters were obtained and analyzed. The results confirmed the presence of two distinct accelerations per cycle. As tempo increased, the percentage of rear acceleration time increased while front acceleration time decreased, along with peak velocities increasing significantly (p&lt;0.01). Rope trajectory analysis indicated a consistent movement pattern across tempos, primarily in the sagittal plane. Variations in skill control showed shorter contact phases and reduced vertical range of motion for the center of gravity and feet at higher tempos (p&lt;0.05), along with significant reductions in joint range of motion for the lower limbs (p&lt;0.01). These findings enhance the understanding of motor control adaptations to different tempos and have practical implications for developing coaching programs aimed at optimizing performance, stability, and efficiency in jump rope training.

In this study, a modular multi-step photometric microflow injection analysis (micro-FIA) system for the automatic determination of Cu(II) in a bioreactor has been developed. The system incorporates diverse 3D-printed modules, including a platform formed by a mixer module to mix Cu(II) with hydroxylamine which reduces Cu(II) to Cu(I) linked to a diluter module via a Tesla valve, a chelation mixer module, a disperser module, and a detector module provided by a LED light source at λ= 455 nm and a light dependence resistor (LDR) as a light intensity detector. The system measures the color intensity resulting from the chelation between Cu(I) and neocuproine. The micro-FIA system has demonstrated good capability for automatic and continuous Cu(II) determination, in a wide range of Cu concentrations from 34 to 2000 mg L-1. The device exhibits a good repeatability (coefficient of variation below 2% across the concentration range), good reproducibility, and has an accuracy of around 100% between 600 to 1900 mg·L-1. Real samples were analyzed using both the micro-FIA system and an atomic absorption spectroscopy method, revealing no statistically significant differences. Additionally, a Tesla valve located before the detector substituted a 3-way solenoid valve, eliminating the need for moving parts.

This study addresses the challenge of treating skin cancer effectively, especially in visible areas like the face, where traditional methods may be undesirable. Current options, including surgery and radiation therapy, have limitations such as complexity, expense, and imprecise dose delivery. The proposed solution involves additively manufacturing personalized patches using diagnostic imaging data, offering a targeted and controlled dose of beta-emitting isotopes like Y-90. The patches, tailored to the tumor's shape and depth, aim to minimize damage to healthy tissues and structures. Through 3D printing technology we demonstrated the feasibility of creating individualized applicators filled with radioisotopes, that have the potential to deliver therapeutic doses while ensuring patient comfort and affordability. This innovative approach, based on radiation delivery simulations, offers a promising future alternative to conventional radiation therapy methods. Clinical trials are required to validate its efficacy and safety, but the potential for reduced radiation exposure and enhanced treatment precision positions this personalized and targeted therapy as a valuable advancement in skin cancer treatment.

Endoscopy has made a significant and noteworthy contribution to the field of medical science and technology. Nevertheless, its potential remains constrained due to the limited availability of rigid or flexible endoscopes. This paper introduces a novel hydraulic actuator based on electrorheological fluid (ERF) as a pivotal advancement in bridging the existing gap within the realm of endoscopy. Following a comprehensive introduction that briefly outlines the electrorheological effect, the subsequent section is dedicated to the elucidation of the actuator’s development process. Challenges arise, particularly in terms of miniaturization and the realization of a hydraulically sealed system with integrated valve electrodes. An internal electrorheological valve system consisting of four valves that are controlled using a pulse-width modulated high voltage was suitable for position control of the antagonistic hydraulic actuators. High-precision stereolithography (SLA) printing has proven practical for manufacturing the actuator components. For functional testing, a test bench was set up in which the actuator follows a setpoint through a PI control loop. The control deviation ranged from 0.6 to 1 degree, with a response time between 6 and 8 seconds. The experiments have demonstrated that, through the use of ERF and integrated valve electrodes, a miniaturized functional actuator can be constructed.

This study presents a novel approach for automating the body condition scoring of dairy cows, leveraging advancements in 3D imaging technology and deep neural networks. The primary objective was to design and implement a system capable of accurately and efficiently assessing the body condition of dairy cows, a critical metric in livestock management for optimizing health and productivity. To achieve this, a 3D camera was employed to capture detailed point cloud data, reconstructing the three-dimensional morphology of individual cows. The obtained data were then fed into a deep neural network, specifically tailored for the task of ranking body condition. The neural network was trained on a diverse dataset of annotated body condition score representing varying degrees of body condition, ensuring robust performance across different physiological states. The results demonstrate the efficacy of the proposed system in automatically and objectively scoring the body condition of dairy cows. The automated process not only expedites the assessment but also reduces the subjectivity associated with manual scoring methods. This innovative approach holds promise for improving the efficiency of dairy farm management by providing timely and accurate body condition assessments. The integration of 3D imaging and deep learning techniques paves the way for future advancements in precision livestock farming, contributing to enhanced animal welfare, optimized production, and sustainable agriculture practices.

Along time, many minted coins were withdrawn from circulation, being replaced with new ones. The returned obsolete metal coins were melted in order to sustainable reuse of the alloy for other purpose. Between the withdrawing and melting, some of the metal coins were cancelled by destruction of the original shape and dimension, using some adequate tools. In the first part, the paper is focused to present some aspects insight of the cancelling method used on the Romanian old nickel coins; also, there are presented some examples. The introductive part also includes the literature review in the field of coin manufacturing, covering the subjects as metal behavior under the striking load, aspects about the 3D modeling and FEM analysis or explaining some striking errors. Result the paper main purpose, to study the particularities of one or another cancelling method applied on subjected coins, which conducted to more or less valuable collection metal pieces. In the paper second part, is introduced the adequate 3D model, computed for the cancelling dies, respectively the coin. Then, there are introduced the assembled models, corresponding to each cancelling case, which consist by the obverse and reverse cancelling dies, having the coin inside them. For the each model, the finite element analysis is realized and is achieved for different initial conditions. The final part of the paper presents the analysis results and also the discussions and conclusions.

The overhead squat movement engages various bodily structures, and its interaction with three-dimensional elastic resistance along the kinetic chain approach remains insufficiently comprehended. This study aimed to describe the scapular kinematics during an overhead squat with the forearm in a supination exercise against an ER and clarify the therapeutic potential of this exercise on scapular rehabilitation. Using an electromagnetic tracking system, we recorded the three-dimensional shoulder kinematics of 19 male participants across seven humeral elevation positions. These positions were captured at 15-degree intervals, spanning from 30 to 120 degrees. The results indicated notable distinctions in scapular upward rotation [F(1,17)=6.09, p=0.024] and scapular posterior tilt [F(1,17)=6.04, p=0.025] between the phases. Furthermore, the interactions revealed significant differences in resistance and phases during humeral elevation for scapular upward/downward rotation [F(3.77,62.48)=7.99, p&lt;0.001], scapular internal/external rotation [F(2.98, 50.64, p&lt;0.001)], and scapular tilt [F(2.58, 43.81)=4.76, p=0.008]. The findings demonstrated that increasing resistance through elastic resistance played a pivotal role in enhancing scapular stability throughout the humerus elevation motion. This underscores the potential of the overhead squat movement as a valuable tool for both shoulder assessment and treatment.

Object detection is important in many applications, such as autonomous driving. While 2D images are lack of depth information and are sensitive to environmental conditions, 3D point cloud can provide accurate depth information and a more descriptive environment. However, sparsity is always a challenge in single-frame point cloud object detection. This paper introduces a two-stage proposal-based feature fusion method for object detection using multiple frames. The proposed method, called proposal features fusion (PFF), utilizes a cosine-similarity approach to associate proposals from multiple frames and employs an attention weighted fusion module to merge features from these proposals. It allows for feature fusion specific to individual objects and offers lower computational complexity while achieving higher precision. The experimental results on the nuScenes dataset demonstrate the effectiveness of our approach, achieving a mAP of 46.7%, which is 1.3% higher than the state-of-the-art 3D object detection method.

We investigate a single-particle density of states in the three-dimensional system described by effective two-band Hamiltonian which describes a ground state in two distant electronic phases: the semimetalic nodal-loop phase and the insulating gapped phase. Analysis of valence bands and Fermi surfaces in both phases indicates that the density of states crucially depends on the parameter in the Hamiltonian of the system that controls a topological alternation of the Fermi surface. The signature of that alternation is expected to play an important role in all quantities closely related to the density of electronic states, such as charge transport and optical conductivity of the system for example.

Introduction Despite efforts to use scaffolds to treat meniscus tears, minimal progress has been made in facilitating meniscus regeneration and return of function. Our research objective was to develop a meniscus repair and regeneration implant by applying a resorbable scaffold in combination with cells and growth factors. We report here the results of using platelet-rich plasma (PRP) as a source of growth factors to induce fibrochondrogenic differentiation of human adipose-derived mesenchymal stem cells (hADSC) in a three-dimensional (3D) Type I collagen-based scaffold in vitro. Methods Scaffold Preparation. Type I collagen scaffolds were prepared following a protocol previously published. Two different densities of scaffolds, high density (HD) and low density (LD), were produced for in vitro study. hADSC and PRP Preparation. hADSCs were cultured to the fifth passage to reach the desired number for experimentation. PRP was collected from human blood and activated. Cell Culture Procedure. Effects of PRP on hADSC proliferation and differentiation into fibrochondrogenic cells were examined in four scaffold groups: LD, HD, LD+PRP and HD+PRP. hADSCs were seeded onto scaffolds (n=5) at a concentration of 2 × 106 cells/scaffold. 1% of PRP was added to the experimental media. Cellular proliferation was assessed at 1, 7, 14, and 21 days. Differentiation was measured using qRT-PCR on Days 14 and 21. qRT-PCR analysis of gene expression was completed with primers for COLLAGEN 1 and AGGRECAN. Data Analysis. ANOVAs were conducted (two-tailed tests) at the .05 significance level. Results Cellular proliferation of hADSCs seeded on each scaffold increased over time. Similar trend was observed for cells seeded on HD scaffolds with and without PRP. hADSC showed significant increase in cellular proliferation on the LD scaffolds at Days 1 and 7. At Day 21, PRP treatment and LD scaffold had a synergistic positive effect on Type I collagen gene expression. PRP did not elevate type I collagen gene in the HD group, the HD scaffold alone had the same level of type I collagen gene expression as LD+PRP. Aggrecan expression was elevated in the presence of PRP in both the HD and LD scaffold groups, indicating enhanced fibrochondrogenic differentiation of hADSCs. Effective cell infiltration was observed across both HD and LD scaffolds with and without PRP treatment. HD scaffolds displayed larger cell clusters and more extensive cell migration over time compared to LD scaffolds. However, LD scaffolds resulted a more uniform cellular distribution than HD scaffolds. Conclusion Our study demonstrates that PRP can play an important role in directing hADSCs towards fibrochondrogenic differentiation in Type I collagen-based scaffolds in vitro. Additionally, our study shows that collagen scaffold density can influence the spatial distribution and cellular behavior of infiltrated cells.

Increasing the availability of alternative protein from insects is important to solving food shortages. Not only are insects a rich source of protein, the use of insect ingredi-ents can reduce food waste. Insects are thus a potentially valuable ingredient for food industries and even food eaten on deep-space missions. The three-dimensional produc-tion of food on space missions has gained attention owing to its potential to reduce au-tonomous food production and produce sustainable food for long-duration space mis-sions. This study investigated the printability and rheological properties of a high-protein food system derived from mealworms and guar gum used as a stabilizer to im-prove printability. Stability and rheological properties were analyzed for various print-ing parameters. The results indicate that as the guar gum concentration was increased from 0 to 1.75%, the yield stress of the mealworm paste increased from 39 to 1096 Pa. Increasing the guar gum concentration thus resulted in a mealworm paste that was more viscous, exhibited shear thinning behavior, could support itself and was thus more stable. In summary, introducing guar gum resulted in a mealworm paste with rheological properties more suitable for printing in terms of printability and stability.

Self-driving vehicles demand efficient and reliable depth sensing technologies. Lidar, with its capacity for long-distance, high-precision measurement, is a crucial component in this pursuit. However, conventional mechanical scanning implementations suffer from reliability, cost, and frame rate limitations. Solid-state lidar solutions have emerged as a promising alternative, but the vast amount of photon data processed and stored using conventional direct time-of-flight (dToF) prevents long-distance sensing unless power-intensive partial histogram approaches are used. In this paper, we introduce a groundbreaking ‘guided’ dToF approach, harnessing external guidance from other onboard sensors to narrow down the depth search space for a power and data-efficient solution. This approach centers around a dToF sensor in-which the exposed time widow of independent pixels can be dynamically adjusted. We utilize a 64-by-32 macropixel dToF sensor and a pair of vision cameras to provide the guiding depth estimates. Our demonstrator captures a dynamic outdoor scene at 3 fps with distances up 75 m. Compared to a conventional full histogram approach, on-chip data is reduced by over 25 times, while the total laser cycles in each frame are reduced by at least 6 times compared to any partial histogram approach. The capability of guided dToF to mitigate multipath reflections is also demonstrated. For self-driving vehicles where a wealth of sensor data is already available, guided dToF opens new possibilities for efficient solid-state lidar.