Optimum selectivity of enhanced oil recovery techniques would play a substantial role in the economic prosperity of petroleum industries which might be virtually eliminated unnecessary expenditures. In this paper, the simultaneous utilization of foaming agent, surfactant polymer (SP), and supercritical carbon dioxide were taken into the investigation under the miscible condition to evaluate the efficiency of each scenario on the cumulative recovery factor, water cut and pressure drop. According to the results of this experimental evaluation, SP-foam flooding had witnessed the highest blockage which is caused to have the maximum recovery factor due to the mobilization of more oil volume in the low permeable pores and cracks. Furthermore, the utilization of surfactant with supercritical carbon dioxide had experienced the least recovery factor regarding the insufficient foam generation which is led to less mobilization of oil phase in the pore throats.

The conventional rolled-up model for carbon nanocones assumes that the cone is constructed from a rolled-up graphene sheet joined seamlessly, which predicts five distinct vertex angles. This model completely ignores any effects due to the changing curvature and all bond lengths and bond angles are assumed to be those for the planar graphene sheet. Clearly curvature effects will become more important closest to the cone vertex, and especially so for the cones with the smaller apex angles. Here we construct carbon nanocones which in the assembled cone are assumed to comprise bond lengths and bond angles which are, as far as possible, equal throughout the structure at the same distance from the conical apex. Predicted bond angles and bond lengths are shown to agree well with those obtained by relaxing the conventional rolled-up model using the LAMMPS software. The major objective here is not simply to model physically realisable carbon nanocones for which numerical procedures are far superior, but rather to produce an improved model that takes into account curvature effects close to the vertex, and from which we may determine an analytical formula which represents an improvement on that for the conventional rolled-up model.

Site environments and instrumental characteristics of carbon dioxide (CO₂) measurements operated by local governments in the Kanto Plain, the center of which is Tokyo were summarized for this study. The observation sites were classified into environments of three types: urban, suburban, and woodland. Based on a few decades of accumulated hourly data, the diurnal and seasonal variations of CO₂ concentrations were analyzed as a composite of anomalies from annual means recorded for each site. In urban areas, the highest concentrations appear before midnight in winter. The second peak corresponds to the morning rush hour and strengthening of the inversion layer. Suburban areas can be characterized as having the highest concentration before dawn and the lowest concentration during the daytime in summer in association with the activation of respiration and photosynthesis of vegetation. In these areas, concentration peaks also appear during the morning rush hour. Woodland areas show background features, with the highest concentration in early spring: higher than the global background by about 5 ppmv.

In this study, functionalized-MWCNTs with 3-aminopropyltriethoxysilane (APTES) loaded titania nanoparticles (MWCNTs-APTES-TiO₂) were prepared to investigate their physicochemical properties and photocatalytic activity for methyl orange (MO) degradation. The TiO₂ nanoparticles, functionalized-MNCNT and composite powders were characterized by XRD, raman, and TEM. The results obtained proved that titania (TiO₂) nanoparticles was successfully loaded on APTES-MWCNTs. The best photocatalytic degradation of methyl orange solution under UV light irradiation was recorded over MWCNTs-APTES-TiO₂ (1:2), with 87% after 180 min. Kinetic analysis indicated that photocatalytic degradation of MO solution by MWCNTs-APTES-TiO₂ obeyed second-order kinetic model (R² > 0.95), supported by half-life equations and graph. The presence of carbon nanotubes accelerated the degradation of methyl orange due to inhibition of electron-hole recombination, the formation of additional hydroxyl radicals and functional groups of the latter had an inhibitory effect on the degradation of methyl orange. This study shows that the MWCNTs-APTES-TiO₂ nanocomposites exhibit promising photocatalytic degradation against methyl orange.

Biomass is a promising alternative and renewable energy source that can be transformed into other value-added products such as activated carbon. In this research, barley husk, corn cob and Agave salmiana leaves were characterized to determine their chemical composition and morphology to evaluate their potentiality as precursors of activated carbons. Based on the main composition results obtained, the biomass samples have suitable chemical and physical characteristics to be considered as good precursors of activated carbons, such as carbon contents greater than 40%, ash content less than 10%, moisture content less than 30%, high volatile contents with values from 75 to 80% and a porous and fibrous morphology. The results indicate that the main compositions in the biomass were cellulose and lignin. The cellulose content was more than lignin (15–26%) for the residues selected. Specifically, a-cellulose contents with values from 52% to 79%, β-cellulose contents of 13–44%, γ-cellulose contents less than 11%, and holocellulose contents of 82–83% were determined. The thermal decomposition for the biomass samples proceeded with five stages attributed to the evaporation of some volatile compounds (70–150 ºC), to the degradation of hemicellulose (180–230 ºC), to the cellulose volatilization (250–350 ºC), to the lignin decomposition (380–550 ºC), and to the degradation of complex polymers and inorganic salts, respectively. The stage corresponding to the cellulose decomposition showed rapid mass decreased in the three residues. This results show that the cellulose and lignin content is another important parameter to evaluate the pyrolysis characteristics of a good precursor of activated carbon.

Starting from the environmental issues related to global warming, climate change and reduction of greenhouse gas emissions, this review paper describes how CO₂ recycling can represent a challenging strategy suitable to explore new concepts and opportunities for catalytic and industrial development. In this view, the production of dimethyl ether (DME) from catalytic hydrogenation of CO₂ appears as a viable technology, able to meet also the ever-increasing need for alternative environmentally-friendly fuels and energy carriers. Basic considerations on thermodynamic aspects controlling DME production from CO₂ are presented, then summarizing the main catalytic systems developed in such a field. Special attention is paid on the role assumed during last years by zeolite-based systems, either in the methanol-to-DME dehydration step or in the one-pot CO₂-to-DME hydrogenation. On the whole, the productivity of DME results significantly to be dependent on several catalyst features, linked not only to the metal-oxide phase responsible for CO₂ activation/hydrogenation, but also to specific properties of the zeolites (i.e., topology, porosity, surface area, acidity, interaction with active metals, distributions of metal particles, …) influencing activity and stability of hybridized bifunctional heterogeneous catalysts.

The aim of this study was to investigate the possibility of a freeform fabrication of porous ceramic parts through selective laser sintering (SLS). SLS was proposed to manufacture ceramic green parts because this additive manufacturing technique can be used to fabricate three-dimensional objects directly without a mold, and the technique has the capability of generating porous ceramics with controlled porosity. However, ceramic printing has yet fully achieved its 3D fabrication capabilities without using polymer binder. Except for the limitation of high melting point, brittleness and low thermal shock resistance from instinct ceramic material properties, the key hurdle lies on very poor absorptivity of oxide ceramics to fiber laser which is widely installed in the commercial SLS equipment. An alternative solution to overcome the poor laser absorptivity via improving material compositions was presented in this study. The positive effect of carbon additive on the absorptivity of silica powder to fiber laser will be discussed. To investigate the capabilities of the SLS process, 3D porous silica structures were successfully prepared and characterized.

The effects of the additives (silicon carbide and titania) and sintering temperatures on the phases developed, physical and mechanical properties of sintered mullite-carbon ceramic composite produced from kaolin and graphite was investigated. The kaolin and graphite of known mineralogical composition were thoroughly blended with 5 and 3 (vol.) % silicon carbide and titania respectively. From the homogeneous mixture of kaolin, graphite and titania, standard samples were prepared via uniaxial compaction. The test samples produced were subjected to firing (sintering) at 1300˚C, 1400˚C and 1500˚C. The sintered samples were characterized for the developed phases using x‐ray diffractometry analysis, microstructural morphology using ultra‐high resolution field emission scanning electron microscope (UHRFEGSEM). Various physical and mechanical properties were determined. It was observed that the addition of SiC/TiO2 additives to the samples made them to possess very low oxidation indices .This also resulted in improvement in the bulk densities and cold crushing strength of the sample when compared with those without additives. It was concluded that the addition of SiC/TiO2 additives improves on the high temperature oxidation resistance of the mullite-carbon ceramic composite sample.

Air pollution is an important public health issue. High levels of carbon monoxide in the atmosphere are hazardous to human health. Studies regarding the concentration of this and other gases in the atmosphere allow political actions to manage and reduce the emission of pollutants. In this context, this paper studied the annual, seasonal and daily variations of carbon monoxide (CO) concentration for the Metropolitan Region of São Paulo (MRSP). We studied three sites in the MRSP, chosen due to the longer time series and the localities. Two of them are located in areas under the influence of heavy vehicle traffic (Osasco and Congonhas) and the third one in a city park (Ibirapuera Park). The results showed high influence of gasoline vehicles on CO emission. In the annual scale, instead of following the increasing number of vehicles, CO emission and concentration decreased due to improvements in emission technology. CO emission showed a seasonal, weekly and diurnal cycle. The highest values of mean concentration were observed in June/July for Osasco (2.20 ppm), Congonhas (2.04 ppm) and Ibirapuera (1.04 ppm), during the morning, due to weak dispersion of the polluting gases.

Biomass materials have received attention for energy storagebecaused of the advantage of low-cost, easy-to-prepare, and eco-friendliness. Three-dimensional carbon materialswith abundant pore structure gradually becomeresearch hotspot in high-performance energy storage. In this study, an easy-to-prepare, green, light and elastic activated carbon was present using the biomass Juncus effusus (JCE) via high-temperature pyrolysis, followed by activation in air. Compared with previously reported bio-carbons, the proposed air-activated bio-carbon contributes in the fabrication of pores to preserve the interconnected, reticular and tubular structure. Moreover, the interconnected porous material also inherits the excellent tenacity of the original JCE such as the material can be bended to below 90^o under an external force while maintaining structural integrity. The activated porous carbon material exhibits an enhanced electric double-layer capacitance (~210 F g^-1 at 1 A g^-1), with capacitance retention of ~78.62% at 10 A g^-1. The interconnected porous carbon microtubes electrode as a double-layer symmetric capacitor exhibits considerable capacitance retention (84%) after 2000 cycles at 1 A g^-1. The improved energy storage performance was proposed to be attributed to the shortened ionic diffusion distance and sufficient contact between the interface of the carbon electrode and electrolyte, which is resulted from the elastic, undamaged structure and types of pores. These results demonstrated that as-preparedcarbon materials have potentional application in symmetric capacitors.

In this study, the causal-effect between carbon dioxide emissions and forestry production and trade was investigated in Ghana by employing a data spanning from 1961 to 2014 by using the VECM and ARDL model. Evidence of the long-run equilibrium relationship in the VECM shows that, a 1% increase in veneer sheet production reduces carbon dioxide emissions by 1.47% in the long-run. There was evidence of a bidirectional causality between carbon dioxide emissions and veneer sheet production, carbon dioxide emissions and wood charcoal production, and a unidirectional causality running from carbon dioxide emissions to wood fuel production and plywood production to carbon dioxide emissions. Evidence from the long-run equilibrium relationship in the ARDL model shows that; a 1% increase in plywood production will increase carbon dioxide emissions by 0.17% in the long-run, a 1% increase in sawnwood production will increase carbon dioxide emissions by 0.17% in the long-run, a 1% increase in wood charcoal production will increase carbon dioxide emissions by 0.36% in the long-run and a 1% increase in wood fuel production will increase carbon dioxide emissions by 0.37% in the long-run.

Reactive NO_x is one of the major air pollutants, which also plays a key role as greenhouse gas. Many research efforts have been devoted to not only detection of NO_x in air but also abatement of NO_x emission. The aim of this mini review is to provide a panoramic snapshot of the electrochemical analysis methods for the emission and detection of NO_x in atmosphere, with special emphasis on NO_x sensor. The electrochemical detecting mechanism and materials for fabricating electrochemical gas sensors are discussed and the prospects and challenges in this area are also evaluated. This work will serve as a useful source to inform the interested audience of the latest developments and applications in the field of NO_x emission and electrochemical detection.

We study a two-echelon supply chain made up of a supplier and a manufacturer, both of which can reduce their component/product carbon emissions. With the vertical technology spillovers, we explore the optimal decisions of centralized and decentralized supply chains with price dependent demand and propose coordination strategy for the decentralized supply chain. Considering the cost contraction effectiveness of the technology spillovers, the centralized and decentralized game theoretic models of a two-echelon supply chain are developed to investigate optimal decisions of pricing and carbon emissions reduction. Through a systematic comparison and numerical analysis, we show that the profits of both players and the entire supply chain improve with the effect of technology spillovers increasing. Carbon emissions reduction will be taken by various protective measures so that the supplier and the manufacturer who do not innovate can hardly share the results of innovating via the “free-riding” methods when the technology spillover is relatively small. We also propose a revenue-cost sharing contract through bargaining to enhance the performance of the decentralized supply chain.

Many tasks in a modern household are done by machines like e.g. a dishwasher or a vacuum cleaner and in the near future most household tasks can be done by smart service robots. This relieves the residents who in turn can enjoy their free time. This newly gained free time turns out to cause the so called spare time rebound effect due to more resource consumption [1,2]. We roughly quantify this rebound effect and propose a CO2 -budget model to reduce or even avoid it. In modern industry, automation and AI take over work from humans, leading to higher productivity of the company as a whole. This is the main reason for economic growth which leads to environmental problems due to higher consumption of natural resources. We show that, even though the effects of automation at home and in the industry are different (free time versus higher productivity) in the end they both lead to more resource consumption and environmental pollution. We discuss possible solutions to this problem such as carbon taxes, emissions trading systems and a carbon budget.

Efficient beam steerable high-gain antennas enable high-speed data rates over long-distance networks, including wireless backhaul, satellite communications (SATCOM), and SATCOM On-the-Move. These characteristics are essential for advancing contemporary wireless communication networks, particularly within 5G and beyond. Various beam-steering solutions have been proposed in the literature, with passive beam-steering mechanisms employing planar metasurfaces emerging as cost-effective, power-efficient, and compact options. These attributes make them well-suited for use in confined spaces, large-scale production and widespread distribution to meet the demands of the mass market. Utilizing a dual-band antenna terminal setup is often advantageous for full duplex communication in wireless systems. Therefore, this article presents a comprehensive review of the dual-band beam steering techniques for enabling full-duplex communication in modern wireless systems, highlighting their design methodologies, scanning mechanisms, physical characteristics, and constraints. Despite the advantages of planar metasurface-based beam steering solutions, literature on dual-band beam steering antennas supporting full duplex communication is limited. This review article identifies research gaps and outlines future directions for developing economically feasible passive dual-band beam-steering solutions for mass deployment.

The detection and recognition of tables in image-based documents is a challenging and essential task for automated data extraction and anal- ysis. This paper introduces a methodology that utilizes Convolutional Neural Networks (CNNs) to address this problem. By harnessing the ro- bust visual recognition abilities of CNNs, the proposed method effectively detects and extracts tables from image-based documents. Additionally, an Encoder-Dual Decoder (EDD) architecture is employed to extract the textual content from table cells, enabling the transformation of visual data into structured, machine-readable formats. This structured data is then further processed using a Vector Space Model (VSM)-based language modeling technique for query-based table retrieval. The methodology’s accuracy is assessed by analyzing the spatial relationships between the extracted cells and comparing them against a pre-defined table structure. The results provide an evidence to the effectiveness of the proposed ap- proach, with an impressive 85% accuracy rate and a corresponding error rate of 15%. This accurate extraction and recognition of tables from image-based documents can significantly enhance applications in data analysis, information retrieval, and knowledge extraction.

Building a new-type power system is the key core of the green and low-carbon development of energy, the restructuring of the power system will inevitably have a linked impact on the coordinated development of the economy-energy-environment (3E) system. This paper constructs a "Dual-Triangle" theoretical framework consisting of the “Energy Trilemma” and the "Sustainable Development Triangle", by combining historical statistical analysis with scenario predictive analysis, analyzes the historical characteristics of the "Dual Triangle" and future development trends under different scenarios, and studies the coupled interaction relationship of the "Dual-Triangle" to explore the optimal transformation path of the power system that is most beneficial to the coordinated development of the 3E system. The conclusions are as follows: (1) The energy system gradually inclined towards economy and cleanliness from 2010 to 2022, the level of coordinated development of the 3E system fluctuated upwards, and the operation status of the "Dual Triangle" was stable. (2) Positive coupling relationship between "Dual Triangle" of scenario S1 is close, which can be regarded as the preferred path for the reconstruction of the power system. Due to phased development has clear development priorities, scenario S2 will artificially break the balance of the “Energy Trilemma”, which is a development model that dynamically mitigates the challenges of the “Energy Trilemma”.(3)The contradiction between economy and cleanliness is continuously weakened, and security has become the core contradiction of the "Impossible Triangle". The combination of renewable energy and energy storage is the key to resolving this contradiction. This paper conducts an integrated and innovative application of the "Dual-Triangle" theory, and the results provide a case basis for how to achieve the coupled interaction of the "Dual-Triangle", promote high-quality energy development, and support the sustainable development of the economy and society.

Models of subsurface structures are important for successful deposit exploration but are challenged by the need to integrate data from different geophysical methods. In the present study, we evaluated a method of joint inversion in which audio-magnetotelluric (AMT) and dual frequency induced polarization (DFIP) data sets are inverted simultaneously to produce a consistent 2D resistivity model to show a clear image of subsurface structures. To achieve the objectives, we conducted AMT and DFIP surveys first on the same survey line within the Dongjun lead-zinc deposit in inner Mongolia by developing 31 AMT survey sites with an interstation separation of 40 m on a 1440 m survey track and operated in fifty-three frequencies in the range 1–10,400 Hz to record the resistivity distribution of subsurface to depths exceeding 800 m. The same survey setup up was applied to the DFIP method by utilizing the SQ-3C model with a pole-dipole array configuration and conducted measurements at frequencies of 4 Hz and 4/13 Hz. We first separately inverted AMT and DFIP measurements. The two-dimensional (2D) model obtained from AMT data revealed distinct low resistivity anomalies in the middle of the 2D inversion model. In contrast, the DFIP inversion model showed a high resistive body in the same region. In response to the discrepancies observed in the separate 2D inversion models, we implemented a joint inversion for both the AMT and DFIP datasets. The joint inversion resistivity model shows surficial conducting bodies and a high conductive body along the profile with relatively high Percent Frequency Effect (PEF) indicating high chargeability. The final joint inversion resistivity model clearly images the large silica alteration zone and the Pb-Zn mineralization. This study demonstrates the feasibility of a joint inversion methodology and highlights the value of integrating geophysical methods through joint inversion for enhanced characterization and exploration of lead-zinc ores.

Cervical cancer, primarily caused by high-risk human papillomavirus (HR-HPV) types 16 and 18, is a major global health concern. Persistent HR-HPV infection can progress from reversible pre-cancerous lesions to invasive cervical cancer, which is driven by the oncogenic activity of human papillomavirus (HPV) genes, particularly E6 and E7. Traditional screening methods, including cytology and HPV testing, have limited sensitivity and specificity. This review explores the ap-plication of p16/Ki-67 dual-staining cytology for cervical cancer screening. This advanced im-munocytochemical method allows for simultaneously detecting p16 and Ki-67 proteins within cervical epithelial cells, offering a more specific approach for triaging HPV-positive women. Dual staining and traditional methods are compared, demonstrating their high sensitivity and negative predictive value but low specificity. The increased sensitivity of dual staining results in higher detection rates of CIN2+ lesions, which is crucial for preventing cervical cancer progression. However, its low specificity may lead to increased false-positive results and unnecessary biopsies. The implications of integrating dual staining into contemporary screening strategies, particularly considering the evolving landscape of HPV vaccination and changes in HPV genotype prevalence are also discussed. New guidelines and further research are necessary to elucidate the long-term effects of integrating dual staining into screening protocols.

The main objective of the paper is to provide a thorough analysis of currently used modulation control schemes for single phase bidirectional dual active bridge DC/DC converter. In this article, it will be shown that single phase shift, extended phase shift and Dual phase shift modulation schemes are special cases of triple phase shift (TPS) modulation scheme. The article aims to highlight six TPS switching modes and their complements with the operational constraints. Unlike previous studies that regarded TPS as a complex scheme, this paper simplifies the analysis of each mode and aims to standardize the understanding of TPS modulation in DAB converters. Power equations, range of power transferred and zero voltage switching (ZVS) are derived for all the modes under TPS without assuming fundamental component analysis. Additionally, a generic optimization algorithm is developed to show the advantages of TPS modulation and thus, detailed analysis presented in this paper provides valuable insights for single phase DAB converter designers in identifying a wide range of optimization algorithms to achieve higher efficiency under TPS modulation. This analysis contributes to the advancement of bidirectional DAB converter technology and facilitates its application in various power electronic systems.

The rapid, sensitive, and selective detection of pathogenic bacteria is of utmost importance in ensuring food safety and preventing the spread of infectious diseases. Here, we present a novel, reusable, and cost-effective impedimetric sensor based on a dual bacteria-imprinted polymer (DBIP) for the specific detection of Escherichia coli O157:H7 and Staphylococcus aureus. The DBIP sensor stands out with its remarkably short fabrication time of just 20 minutes, achieved through the efficient electro-polymerization of o-phenylenediamine monomer in the presence of dual bacterial templates, followed by in-situ template removal. The key structural feature of the DBIP sensor lies in the cavity-free imprinting sites, indicative of a thin layer of bacterial surface imprinting. This facilitates rapid rebinding of the target bacteria within a mere 15 minutes, while the sensing interface regenerates in just 10 minutes, enhancing the sensor's overall efficiency. A notable advantage of the DBIP sensor is its exceptional selectivity, capable of distinguishing the target bacteria from closely related bacterial strains, including different serotypes. Moreover, the sensor exhibits high sensitivity, showcasing a low detection limit of approximately 9 CFU mL-1. The sensor's reusability further enhances its cost-effectiveness, reducing the need for frequent sensor replacements. The practicality of the DBIP sensor was demonstrated in the analysis of real apple juice samples, yielding good recoveries. The integration of quick fabrication, high selectivity, rapid response, sensitivity, and reusability makes the DBIP sensor a promising solution for monitoring pathogenic bacteria, playing a crucial role in ensuring food safety and safeguarding public health.

In IP networks, packet forwarding is destination-based and hop-by-hop, and routes are built as needed. Kwong et al. introduced a protection routing in which packet delivery to the destination node can proceed uninterrupted in the event of any single node or link failure. He then shows that “whether there is a protection routing to the destination” is NP-complete. Tapolcai find that two completely independent spanning trees, abbreviated as CISTs, can be used to configure the protection routing. In this paper, we propose dual protection routing trees, denoted as dual-PRTs to replace CISTs, which are less restrictive than CISTs. Next, we propose a transformation algorithm that uses dual-PRTs to configure the protection routing. Taking complete graphs Kn, complete bipartite graphs Km,n, hypercubes Qn, locally twisted cubes LTQn as examples, we provide a recursive method to construct dual-PRTs on them. This article will show that there are no two CISTs on K3,3, Q3, and LTQ3, but there exist dual-PRTs that can be used to configure the protection routing. As shown in the performance evaluation of simulation results, for both Qn and LTQn, we get the average path length of protection routing configured by dual-PRTs is shorter than that by two CISTs.

Kinetic parameters of SO2 adsorption on unburned carbons from lignite fly ash and activated carbons based on hard coal dust were determined. The model studies were performed using the linear and non-linear regression method for the following models: pseudo first and second-order, intraparticle diffusion, and chemisorption on a heterogeneous surface. The quality of the fitting of a given model to empirical data was assessed based on: R2, R, Δq, SSE, ARE, χ2, HYBRID, MPSD, EABS, and SNE. It was clearly shown that it is the linear regression that more accurately reflects the behaviour of the adsorption system, which is consistent with the first-order kinetic reaction – for activated carbons (SO2+Ar) or chemisorption on a heterogeneous surface – for unburned carbons (SO2+Ar and SO2+Ar+H2O(g)+O2) and activated carbons (SO2+Ar+H2O(g)+O2). Importantly, usually, each of the approaches (linear/non-linear) indicated a different mechanism of the studied phenomenon. A certain universality of the χ2 and HYBRID functions has been proved, the minimization of which repeatedly led to the lowest SNE values for the indicated models. Fitting data by any of the non-linear equations based on the R or R2 functions only, cannot be treated as evidence/prerequisite of the existence of a given adsorption mechanism.

People wore clothes for warmth, survival and necessity in modern life as well but in modern era, eco-friendliness, shorten production time, design, and intelligence also matters. The seamless bonding technology strengthen the bond between fabrics in textiles, while Grey relational analysis (GRA) can be applied to fabrics to measure the relationship between data series and determine the closeness of each data series. In this study, polyurethane prepolymer, 2-Hydroxyethyl acrylate (2-HEA) as an end-capping agent, and n-octyl acrylate (ODA) as a photo-initiator were used to synthesize dual-curing polyurethane hot-melt adhesive. The Taguchi quality engineering and grey relational analysis used to discuss the influence of different mole ratio of NCO:OH, and the effect of the molar ratio of addition of octyl decyl acrylate on the mechanical strength. The Fourier transform infrared spectroscopy (FTIR) results showed the termination of prepolymer's polymerization reaction and the C=O peak intensity at 1730 cm-1 indicating the efficient bonding to main chain. The high molecular weight polymer (20,000-30,000) described by advanced polymer chromatography (APC) confirmed the polyurethane polymer bonded with octyl decyl acrylate to achieve the photo-thermosetting effect. The thermogravimetric analysis (TGA) results showed the thermal decomposition temperature of polyurethane hot melt adhesive also increased and highest pyrolysis temperature (349.89℃) for the polyhydric alcohols. The high value of shear strength (34.94 kg/cm2) as well as peel strength (1.68 kg/cm) were also observed in dual-cure photo-thermosetting polyurethane hot melt adhesive. The signal-to-noise ratio also used to generate the grey relational degree. It was observed that the best parameter ration of NCO: OH was 4:1 with 5 moles of monomer. The Taguchi quality engineering method was used to find the parameters of single quality optimization, and then the grey relation calculation was used to obtain the parameter combination of multi-quality optimization for thermosetting polyurethane hot melt adhesive. The study aims to meet the requirements of seamless bonding in textile factories and optimized experimental parameter design by setting target values can effectively increase production speed, reduce processing time and costs as well.

A series of defective ZSM-5 zeolites (~300 nm, SiO₂/Al₂O₃ ratio of 55, 100, 400 and 950) were intentionally prepared and systematically studied by XRD, SEM, ²⁹Si MAS NMR, argon physisorption, NH₃-TPD and FT-IR technologies. The nature, the amount and the accessibility of the acid sites of defective ZSM-5 zeolites are greatly different from reported ZSM-5 zeolites with perfect crystal structure. The co-existed strong Brønsted acid sites (Si(OH)Al) and weak Brønsted acid sites (hydroxyl nests) over defective ZSM-5 zeolites might lead to unique catalytic function. Zn(C₂H₅)₂ was grafted onto defective ZSM-5 zeolites through chemical liquid deposition (CLD) method. Interestingly, FT-IR spectroscopy studies find that Zn(C₂H₅)₂ was preferentially grafted on the hydroxyl nests with weak acidity rather than the Si(OH)Al groups with strong acidity over different defective ZSM-5 zeolites. Particularly, home-built operando dual beam FTIR-MS was applied to study the catalytic performance of Zn species locating at different sites of defective ZSM-5 zeolites under n-hexane transformation. Results show that Zn species grafted over hydroxyl nests obtain better dehydrogenation performance than Zn species over framework aluminum. This study provides guidance for the rational design of highly efficient alkane dehydrogenative aromatization catalysts.

The mechanical properties and microstructure of recycled aggregate concrete (RAC) with carbon fibers (CF) and nano-SiO2 (NS) were investigated in this paper. The mechanical properties of RAC were enhanced by both single and hybrid addition of CF and NS, and the hybrid addition had a better strengthening effect. From the experimental results, it was found that the addition of CF could increase the 28d compressive strength and splitting strength of RAC by 9.05% and 22.36% respectively. Hybrid CF and NS were more conducive to improve the mechanical properties of RAC, and the enhancement effect increased first and then decreased with the increase of NS content. The optimal content of NS was 0.8wt%, which increased the 28d compressive strength and splitting strength of RAC by 20.51% and 14.53% respectively. The microstructure results indicated that the addition of CF had little effect on optimization pore structure of RAC, but the crack-inhibition action of the CF could improve the mechanical properties of RAC. The addition of NS reduced the content of CH and facilitated the formation of more (C–S–H) gel. The hydrated calcium silicate (C–S–H) gel significantly decreased the porosity and transformed harmful capillaries pores and harmful pores into harmless capillaries pores and gel pores, thus improving the mechanical properties of RAC. Therefore, the hybrid CF and NS was more conducive to enhance the performance of RAC for building materials.

This report summarizes the findings of a deep retrofitting modelling study of four government buildings across the UAE. Buildings envelope assessment, HVAC, and electrical systems design, installed conditions, maintenance practices and operation methods, and rigorous engineering analysis has been performed for the four buildings to produce calibrated energy models that confirm a good correlation between actual annual energy consumption and advanced simulated energy modeling results. IES-VE software, ASHRAE Guideline 14, and IPMVP were the basis of the energy model calibration based on actual data. Energy retrofitting options were applied to the calibrated energy models of the four government buildings where advanced computational modeling studies have been utilized to analyze different thermal envelope components and external fabric energy efficiency measures in conjunction with the actual HVAC systems. The results have shown that it may be financially challenging to implement a single envelope retrofitting measure on any of the four buildings due to high payback periods. Nevertheless, when conducting an optimization through a holistic building approach targeting the overall envelope enhancements, the financial modeling results provide significantly improved and provide reduced payback periods of the solutions, making them more attractive to investors. Based on the energy modeling results and the cost of the various proposed building envelope solutions provided by Saint-Gobain, the payback period in all cases varies between 15 to 20 years. However, huge savings in terms of carbon emissions are achieved by implementing the deep retrofitting measures, crucial to achieving carbon neutrality within the UAE built environment. Deep retrofitting is a promising segment of the execution roadmap as part of the UAE's decarbonization journey; even though it is capital-intensive upfront, it has a major impact on long-term operational savings. Moreover, it is often more cost-effective than building new and energy-efficient structures from scratch. The findings indicate that deep retrofitting can be a techno-financially viable solution if it is well-planned during major refurbishment or as part of building maintenance. It has significant potential to reduce carbon emissions while also providing a range of benefits such as operational cost savings, improved thermal comfort – a feature which has a direct impact on perceived efficiency and productivity at work, indoor air quality, improved asset value, reputational enhancement, and better choice for environmentally-cautious tenants or buyers.

Solid propellants have significant applications in aerospace, and improving their combustion performance has become a hot research topic in recent years. Carbon black (CB) has been widely used in the field of catalytic pyrolysis due to its low cost, controllable morphology, and ease of modification. Herein, we first investigates the structure-activity relationship between the physicochemical properties of nine types of CB with a particle size range of 1-15 μm and a mass fraction of 5%, including oil absorption value, compression oil absorption value, and oxygen content, and the catalytic pyrolysis of ammonium perchlorate (AP), concluding that the function relationship between oil absorption value and high-temperature peak is Y1=1032.67-9.618x+0.038x2, the function relationship between compression oil absorption value and high-temperature peak is Y2=145.537+62.365ln(x), and the function relationship between oxygen content and high-temperature peak is Y3=e(6.085-0.02/x). Based on these, we further uses coal tar, which is abundant in sources, as the raw material to prepare five types of coal-based CB marked as CB1-CB5 at pyrolysis temperatures of 1000~1800 ℃. The relative error between the actual peak value and the predicted value of the CB/AP composite particles is less than 5%, proving that the peak temperature model of CB/AP composite particles can guide actual production. This study contributes to promoting CB application in improving the catalytic pyrolysis performance of ammonium perchlorate and enhancing the high added value utilization of coal-derived products.

Biowaste sources, like coffee wastes (CWs), are considered for advanced materials. CW was assessed to prepare activated carbon for supercapacitor electrodes, but showed low performance compared to other counterparts. Enhanced CW activation process may help address this limitation. In this study, CW was subjected to two activation methods: physical (pyrolysis) activation and physical-chemical activation using ZnCl2, to determine the more effective approach. Both resulting materials were analyzed using SEM, TEM, BET, Raman spectroscopy and XRD. The physical-chemical activation yielded activated carbon with better characteristics, including a higher specific-surface area (SSA) of ~830 m²/g, compared to 458 m²/g from the physical activation. With its promising potential for supercapacitor electrodes, the former activated carbon was singled out for supercapacitor study. Cyclic voltammetry revealed a specific capacitance of 261 F g-1, and energy density of 18.3 Wh/kg, with power density of 360 W/kg at a current density 0.33 A/g. Charge-discharge studies showed a specific capacitance of 150 F g-1 at the same current density. Electrochemical impedance spectroscopy indicated a specific capacitance of 180 F g-1, with an equivalent series resistance of 0.56 Ω at a low frequency of 0.01 Hz. The electrode exhibited exceptional characteristics, maintaining high stability over 5,000 charge-discharge cycles.

Additive Manufacturing (AM) methods are increasingly beign abopted in the industry as an alternative for mass production. In particular, Fused Deposition Modeling (FDM) technology is leading the way in this field. However, the adhesion of layers in products produced using FDM technology is an important issue. These products are particularly vulnerable to forces acting parallel to the layers and specially to impact strength. This study aims to optimize the impact strength against loads acting parallel to the layers (ZX orientation) of PA6, one of the most widely used materials in the industry. This orientation is critical in term of mechanical properties, and the mechanical characteristics are significantly lower compared to other orientation. In this study, filaments containing pure PA6 with 15% short carbon fiber and 30% glass fiber were utilized. Additionally, printing temperature, layer thickness and heat treatment duration were used as independent variables. An L9 orthogonal array was employed in this study, and each experiment was repeated three times to conduct impact strength tests. Characterization, Taguchi optimization, a factor analyses were performed, followed by fracture surface characterization by SEM. As a result, the highest impact strength was achieved with pure PA6 at 8.9 kJ/m2, followed by PA6 GF30 at 8.1 kJ/m2 and the lowest impact strength was obtained with PA6 CF15 at 6.258 kJ/m2. When compared to the literature and manufacturer datasheets, it was concluded that the impact strength values have significantly increased, and the chosen experimental factors and their levels, particularly nozzle temperature, were effective.

This paper presents the novel development of a shape memory polymer foam based on polymer-polymer nanocomposites. Herein, polylactide (PLA)/biosourced polyamide (PA) foams are fabricated by in-situ fibrillation of polymer blends and subsequent supercritical CO2 foaming technique. In this system, PLA serves as a shape memory polymer to endow this foam with a shape memory effect (SME), and in-situ generated PA nanofibers are employed to reinforce the PLA cell walls and provide an additional permanent phase. Concentration of PA, 5 wt.%, is chosen to form an entangled nanofibrillar network. Foams of PLA/PA nanoblends with the same content of constituents are fabricated to reveal the effect of minor phase morphology on the cell structure and shape memory behavior of polymer foams. Profiting from the reinforcing effect of PA nanofibers, the PLA/PA nanocomposite foam exhibits smaller foam cells, a narrower cell size distribution and a comparable cell concentration than the PLA/PA nanoblend foam. In addition, PA nanofibers, unlike PA nanodroplets, favor the shape fixation ratio and recovery ratio and shorten the shape recovery time.

High mountain rainforests are vital in the global energy and carbon cycle. Understanding the exchange of energy and carbon plays an important role to reflect responses to climate change. In this study, an eddy-covariance (EC) measurement system installed in the high Andean Mountains of South Ecuador was used. As EC measurements are affected by heterogeneous topography and vegetation height, the main objective was to estimate the effect of the sloped terrain and the forest on the turbulent energy and carbon fluxes considering the energy balance closure (EBC) and the heat storage. The results showed that the performance of the EBC was generally good and estimated to be 79.5%. This could be improved when the heat storage effect was considered. Based on the variability of the residuals in the diel modifications in the imbalances were highlighted. Particularly, during daytime residuals were largest (56.9 W/m² on average) with a clear overestimation. At nighttime mean imbalances were rather weak (6.5 W/m²) and mostly positive, while strongest underestimations developed in the transition period to morning hours (down to -100 W/m²). With respect to the Monin-Obukhov stability parameter ((z-d)/L) and the friction velocity (u*) it was revealed that largest overestimations evolved in weak unstable and very stable conditions associated with large u* values. In contrast, underestimation was related to very unstable conditions. The estimated carbon fluxes were independently modelled with a non-linear regression using a light-response relationship and reached a good performance (R²=0.52). All fluxes were additionally examined in the annual course to estimate whether both, energy and carbon fluxes, resembled the microclimatological conditions of the study site. This unique study demonstrated that EC measurements provide valuable insights into land surface -atmosphere interactions and contribute to our understanding of energy and carbon exchanges. Moreover, the flux data provide an important basis to validate coupled atmosphere ecosystem models.

This study presents the development of a diglycidyl monomer containing two imine groups that can act as dynamic and reversible bonds. During the curing of the monomer with two different amine hardeners, we confirmed the formation of new imine groups due to the transamination reaction, not reported before, between the imine groups of the diepoxy monomer with the amine groups of the hardener. The effect of this structural change is observed for the first time in the stress relaxation behavior, resulting in the overlapping of two different relaxation modes. The analytical modelling could extract two distinct characteristic relaxation times using a double-element Maxwell model. A second characterization of the stress relaxation process by frequency sweep experiments was performed to corroborate the results obtained, confirming speedy stress relaxation. Acid-catalyzed hydrolysis was performed on the studied materials, demonstrating the complete degradation of the network. We finally confirmed that the synthesized diepoxy compound is suitable for preparing carbon fiber-reinforced composite materials, demonstrating easy fiber impregnation, fast reshaping and especially a total degradation of the polymer matrix that allows the recovery of the carbon fibers in mild conditions. This epoxy-amine system is an excellent candidate for overcoming the traditional limits of thermosets in preparing fiber-reinforced composites.

Titanium alloys, notably Ti6Al4V, are frequently employed in biomedical applications due to their high mechanical strength and biocompatibility. But improving their surface qualities like biocompatibility and resistance to corrosion remains a crucial topic of study. This study investigates the effects of rhenium-carbon coatings deposited on Ti6Al4V substrates using magnetron sputtering technique with a molybdenum anchoring layer. Despite successful formation of rhenium carbides, elemental rhenium, and rhenium oxides confirmed by EDS and XRD analysis, the coatings exhibited poor adhesion, resulting in significant delamination as observed in SEM images. Corrosion resistance tests revealed that the coatings adversely affected the Ti6Al4V substrate, as indicated by increased corrosion current densities and more negative corrosion potentials in potentiodynamic polarization tests. Biocompatibility assessments using PK15 cells showed a notable reduction in cell viability and metabolic activity, particularly with coatings of higher surface roughness. These findings underscore the need for improved surface preparation and coating processes to enhance adhesion and biocompatibility of rhenium-carbon coatings on Ti6Al4V substrates. Future research should focus on optimizing coating adhesion, investigating cytotoxicity mechanisms related to surface roughness, and expanding biocompatibility evaluations to various cell types and biological environments.

In this work, a method for measuring tow angles in carbon fiber components, based on the use of a polarized camera, is analyzed from a metrological point of view. Carbon fibers alter the direction of the reflected light electrical field, so that in each point of the surface of a composite piece the angle of polarization of reflected light matches the fiber orientation. A statistical analysis of the angle of linear polarization (AoLP) in each pixel of each examined area allows to evaluate the average winding angle. An evaluation of the measurement uncertainty of the method on a cylinder obtained by a filament winding process is carried out, and the result appears adequate for the study of the distribution of angles along the surface of the piece, in order to optimize the process.

This study investigates the characteristics of activated carbons derived from biomass plant residues: rice husk (OSL) of the genus Oryza, reed stalks (PhAC) of the genus Phragmites, pine sawdust (PSL) of the genus Pinus, and wheat straw (TAL) of the genus Triticum. Activation was carried out using potassium hydroxide, employing a two-stage pyrolysis under air. The study examined the influence of activation temperature, duration, concentration of the impregnating agent, and impregnation time. Characteristics such as sorbent porosity, bulk density, and hydrocarbon sorption capacity were determined. Adsorption capacity was assessed using BET analysis and the iodine number determination method, with the highest iodine number achieved being 2809 mg/g, indicating high adsorption capability. The structural morphology of the activated carbons was evaluated by SEM, and their chemical surface characteristics were identified by IR spectroscopy. Computational analysis of the nitrogen sorption isotherms using the Barrett-Joyner-Halenda (B-J-H) method and the Dubinin-Radushkevich (D-R) equation showed that activated carbon samples from rice husk and pine sawdust possess a developed specific surface area and contain micro- and mesopores. The Dubinin-Astakhov (D-A) approach was used to study the pore diameter of activated carbon, revealing significant findings on pore structure. The maximum micropore volume was found in activated carbon samples from pine sawdust (PSL), measuring 0.46 cm³/g. All activated carbon samples of plant origin were tested under field conditions for the remediation of oil-contaminated areas near the “Zhanatalap” oil field in the Atyrau region. By the 16th day, the oil-contaminated soil treated with rice husk activated carbon was cleaned by 67.1%.

This paper, from the perspective of Mode 3 of knowledge production, takes the important carrier of knowledge, scientific research papers, as the research object. The mainstream databases (SCIE and SSCI) are chosen as the data sources. Firstly, bibliometric methods are applied to analyze the cooperation status among the main bodies of paper production, including authors and their affiliated institutions, countries, and disciplines; secondly, the Analytic Hierarchy Process (AHP) is used to construct a comprehensive evaluation model for the state of research cooperation in carbon neutrality. Based on the evaluation model, the cooperation characteristics of different disciplinary fields and the relationship between paper cooperation status and high-impact research papers are comparatively analyzed. At the same time, an analysis is conducted on the support from the government, the sponsorship from enterprises, and the participation of the public in the process of paper production. Finally, some suggestions are put forward on how to build an innovative ecosystem for carbon neutrality research from the perspective of Mode 3 of knowledge production.

Pseudomonas donghuensis P482 exhibits broad antibacterial and antifungal activity, primarily related to the production of 7-hydroxytropolone (7-HT). However, the restricted nutritional conditions (viz. mineral medium with single carbon source) diminished the antagonistic activity of P482. In this study, we unveil profiles of the secondary metabolites from P482 and its selected mutants, using nutrient-diluted (10% tryptone soy broth, TSB) and nutrient-restricted (M9 with either 0.4% glucose or 0.4% glycerol as a sole carbon source) media to explore differences in the quantity and quality of the secondary metabolites produced. No 7-HT was found to be synthetized by P482 under restricted nutritional conditions. However, both the wild-type and the tested mutants of P482 still did express some antagonistic activity towards the plant pathogenic bacteria tested. Based on these results, we postulate that 7-HT is not the sole antimicrobial compound produced by P. donghuensis P482 and that other antimicrobials may be involved in P482 antagonistic activity under limiting-nutrient conditions.

Particulate organic carbon (POC) is a pivotal component within the marine carbon cycle, actively involved in diverse biogeochemical processes. This study focuses on Mediterranean as the research region, selecting the most influential factors from 47 potential ones influencing surface POC. Using geographic detector for factor identification, ten primary influencers were identified. Preliminarily optimized random forest (BRF), backpropagation neural network, adaptive boosting, and extreme gradient boosting were utilized to construct POC assessment models. Notably BRF exhibited superior performance in estimating the sea surface POC. Further optimization of RF using the tuneRanger R package resulted in R² of 0.868, mean squared error of 1.119 (mg/m³) ², and mean absolute error of 1.041 (mg/m³). Surface POC concentrations in the Mediterranean for May and June 2017 were estimated. Spatial distribution analysis unveiled higher concentrations in the west, lower in the east, higher in the north, lower in the south, with higher levels near the coast and lower far from the coast. Additionally, the study deliberated on the impact of human activities on surface POC in the Mediterranean. This research contributes a high-precision method for satellite retrieval of surface POC concentrations in the Mediterranean, thereby enriching the understanding of POC dynamics in the area.

As prominent oil producers, the Gulf Cooperation Council (GCC) countries have played a significant role in the global energy market. However, as the world's attention increasingly shifts towards environmental sustainability, understanding the implications of the GCC's economic activities on CO2 emissions becomes indispensable. This research paper investigates the relationship between specific economic indicators and their impact on CO2 emissions in the GCC from 2001 to 2021. The study employs quantile regression, a powerful statistical method that estimates the conditional quantiles of a response variable given a set of predictor variables. The findings reveal several important insights: Financial institution efficiency is significant and negative at a 1% level at the lower (10th) -83537.3 and the higher quantile (90th) -549002.3. The relationship between GDP per capita and CO2 emissions varies across quantiles, highlighting the complexity of the growth-environment nexus. Total patents exhibit a positive and significant relationship with emissions, underscoring the importance of directing innovation towards environmentally sustainable solutions. Renewable energy consumption displays a nuanced relationship with CO2 emissions, with a stronger negative impact observed at higher consumption levels. This underscores the potential of renewable energy to mitigate emissions when integrated at scale. The study's outcomes hold crucial policy implications for the GCC countries as they seek to align economic growth with environmental sustainability. The findings emphasize the importance of fostering financial institution efficiency, promoting green innovation, and expanding renewable energy sources to reduce emissions

Two methods for Pd nanoparticle synthesis were explored with three different carbide-derived carbon (CDC) support materials of which one was nitrogen-doped. These materials were studied for oxygen reduction reaction (ORR) in 0.1 M KOH solution. The prepared CDC/Pd catalysts were characterized using TEM, XRD and XPS. Using these methods, we can observe the influence of support materials for one-pot synthesis methods as we use the standard citrate method and polyol method with polyvinylpyrrolidone (PVP) as a capping agent. Comparing the two methods N-doping of carbon material resulted in smaller nanoparticles only in the case of citrate synthesis, suggesting that the influence of support is weaker using polyol method. Citrate method on CDC1, which was predominantly microporous led to a higher degree of agglomeration and larger particle formation in comparison to CDC2 and CDC3 supports, which possessed higher degree of mesoporosity. Smaller Pd particle sizes were achieved using citrate and NaBH4 in comparison to the ethylene glycol-PVP method. CDC2 and CDC3 did not show significant difference suggesting that the N-doping did not have much of an influence on the ORR. Highest SA value was observed on CDC1/Pd_Cit, which could be attributed to formation of larger particles and agglomerates.

Environmental preservation presents numerous challenges, particularly in capturing carbon di-oxide. Despite multiple studies on this topic, there remains a need for additional capture plants, particularly in the energy sector. The power industry emits flue gas during its post-combustion process, and capturing carbon dioxide from this gas would make power plants more environ-mentally friendly while aiding the preservation of the planet. The work conducted in This study aimed to investigate the gap in knowledge to contribute to the development of a better world without harming it. The identified research gap reveals no established optimal monoethanola-mine (MEA) solvent concentration for the process. A simulation was performed using Aspen Hysys to analyze the absorption efficiency at higher solvent concentrations and address this is-sue. The input data was obtained from a flue gas capture plant in the UK. The results obtained from discrete increments indicate an optimal solid result for an MEA concentration of 36 wt.%. Further analysis of temperature and pressure revealed that other solvents, such as diethanola-mine (DEA) and triethanolamine (TEA), are more stable at higher concentrations and that DEA and TEA at the same concentration as MEA consumed significantly less energy to capture carbon dioxide.

This paper explores the role of agroforestry in mitigating climate change by sequestering atmospheric carbon in the tropics and subtropics, specifically in the Madhupur Sal forest of Bangladesh. Agroforestry, combining trees with crops on agricultural lands, is recognized for its potential to act as carbon sinks and enhance productivity. The study assesses various agroforestry practices, including Acacia-Pineapple-Turmeric-Papaya, Acacia-Pineapple-Zinger-Banana, and Sal-Pineapple-Aroid combinations. The research reveals improved farm productivity in these agroforestry systems, with different tree species sequestering varying amounts of carbon. Acacia species, ranging from 12 to 25ft in height, sequestered an average of 23.35 lbs/year, while Sal species (Shorea robusta), with trees 45 to 61ft tall, sequestered 49.80 lbs/year on average. Factors such as tree height, diameter at breast height (DBH), number of leaves, and branches influence carbon sequestration. The paper suggests integrating the carbon trading system of the Clean Development Mechanism (CDM) with Carbon Sequestration (CS) potential to leverage agroforestry for greenhouse gas emission reduction in Bangladesh. By emphasizing the profitability of these practices alongside carbon sequestration, the study encourages the adoption of agroforestry as a sustainable and economically viable strategy for climate change mitigation.

The long-term use of fertilizers and pesticides in conventional cultivation has resulted in a decrease in soil productivity and vegetable yields in greenhouses. However, only a limited number of studies have explored the impacts of organic cultivation on greenhouse soil. Specifically, there is a scarcity of research examining the alterations in soil aggregate mediated organic carbon and microbial communities, which are known to enhance soil productivity. This study investigated the properties of soil aggregates, including the levels of organic carbon fractions, microbial community, and enzyme activity with the three aggregate classes microaggregates (<0.25 mm), small macroaggregates (2-0.25 mm) and large macroaggregates (>2 mm). These investigations were conducted under three different cultivation methods in a greenhouse: conventional cultivation (CC), integrated cultivation (IC), and organic cultivation (OC) in greenhouse. The results showed that (1) OC and IC promoted the formation of small macro-aggregates and enhanced aggregate stability compared to CC, (2) SOC in the three size fractions of OC increased by 98.99%-92.06% compared to CC; EOC increased by 98.47%-117.59%; POC increased by 138.59%-208.70%; MBC increased by 104.71%-230.61%; DOC increased by 21.93%-40.90%, respectively; (3) Organic cultivation significantly increased enzyme activity in all three particle size aggregates and increased the relative abundance of bacteria in micro-aggregates as well as the relative abundance of fungi in small macro-aggregates. Structural equation model (SEM) analysis revealed that organic farming practices fostered the development of smaller macro-aggregates, elevated microbial and enzyme activities within soil aggregates, and facilitated the conversion of soil nutrients and carbon sequestration. consequently, this led to an increase in soil organic carbon content and improved vegetable yield in greenhouse environments. In conclusion, the soil carbon content and vegetable yield are enhanced through long-term organic cultivation in greenhouses, primarily by increasing the proportion of small macro-aggregates.

Shape-shifting polymers are widely used in various fields such as intelligent switches, soft robots and sensors, which require both multiple stimulus response functions and qualified mechanical strength. In this study, a novel near infrared light (NIR) responsible shape-shifting hydrogel system was designed and fabricated, through embedding vinylsilane modified carbon nanotubes (CNTs) into particle-double network (P-DN) hydrogels by micellar copolymerization. The dispersed brittle Poly(sodium 2-acrylamido-2-methylpropane-1-sulfonate) (PNaAMPS) network of the microgels can serves as sacrificial bonds to toughen the hydrogels, and the CNTs endow it NIR photothermal conversion ability. The results show that the CNTs embedded P-DN hydrogels present excellent mechanical strength, i. e. fracture strength of 312 kPa and fracture strain of 357%. Moreover, an asymmetric bilayer hydrogel, where the active layer contains CNTs, can achieve 0°–110° bending deformation within 10 min under NIR irradiation and can realise complex deformation movement. This study provides a theoretical and experimental basis for the design and manufacture of photoresponsive soft actuators.

In Tunisia, olive is the most cultivated fruit crop while in the north where rainfall exceeded 400mm.year-1, the olive growing area is in widely extension in marginal soil with high slope gradient. Thus, the inclusion of cover crops is a sustainable solution to increase the ecosystem productivity, improve the soil fertility and oil yields. But, in Tunisia a few study were investigated the effect of legumes cover crop on the olive productivity. Therefore, the aim of this study was to evaluate the short-term (two cropping seasons s 2021 and 2022) effects of different seeded cover crops and soil management practices on the cover crops and soil characteristics, as well as enzymes activities and related microbial diversity. Six intercropping were tested in rainfed olive orchards (cv.Chétoui): Spontaneous vegetation (Spont), Wheat, Vetch, Oat, Fenugreek, mixture Vetch-Oat and compared to control (3 periodic tillage/year without intercropping). During the first cropping season, cover crops were cut as animal feed and only residues were incorporated into the soil. While, during the second year, all cover crops biomass were incorporated into the soil. Results indicate that the dry biomass and carbon uptake were significantly higher in grasses species (Wheat and Oat). But, highest level of nitrogen was found in Fenugreek cover crops. As compared to control, all cover crops including spontaneous vegetation increased soil organic matter and macronutrient level, mainly phosphorus. The most activity of β-glucosidase, phosphatase and arysulphatase was found in the cover crops plot of wheat and oat. In addition, this study improve that the utilization of the carbon sources was dominated by amides, amine and amino-acids in the fenugreek plot; while it was dominated by polymers and carboxylic acids in the case of wheat and oat.

The escalating levels of atmospheric carbon dioxide (CO₂) due to anthropogenic activities have raised significant concerns regarding their far-reaching consequences, including potential impacts on human brain function. This study employs Agent-Based Modeling (ABM) and a comprehensive literature review to comprehensively examine the effects of varying atmospheric CO₂ concentrations on human brain activity. Historical and projected CO₂concentration data, along with neuroscientific insights, were integrated into the ABM framework to simulate brain activity responses under different CO₂ scenarios. The simulations revealed that elevated CO₂ levels disrupt neural activity and alter neurotransmitter profiles, indicating potential cognitive consequences. Sensitivity analysis emphasized the importance of accurate parameterization for robust simulations. The findings underscore the urgent need to address global CO₂ emissions to preserve cognitive health. Further research is essential to validate and refine the model, incorporating additional factors for a comprehensive understanding of the cognitive repercussions of rising CO₂ levels, crucial for informed policy-making and public awareness campaigns.

This paper examines the interplay between media and the “social side of soils” whereby climate change action implicates individual and collective capacity to adapt, participate in groups or organizations, networks, and respond to challenges and opportunities across a system. The context examined here is Canadian agriculture, and soil health initiatives in the province of Ontario. Our review of relevant literature points to a knowledge gap on the role of the media in enabling climate action in the Canadian agricultural sector with a focus on soil management practices. This study conducted a media content analysis of 100 English-language news articles published between 2022 and 2024 and conducted 31 surveys with media professionals. Approximately one-quarter of the screened news articles contained any relevant coverage of soil health-related climate change mitigation issues. Journalist surveys identified the resource constraints on soil health media coverage with a wide range of traditional and Internet-based journalism on climate change issues, motivated particularly by crisis communication and one-off “parachute reporting”. Going forward, the engagement of key stakeholders of soil health in Canada such as farmers for media and communication about climate change mitigation needs attention. Key policy structures at the federal and provincial levels can help to make this happen.

Green carbon-based materials (GCM), i.e. carbon materials produced using renewable biomass or recycled wastes, ought to be used in order to processes become sustainable and carbon neutral. Carbon nanomaterials, like for example carbon dots and nanobichar families, and carbon materials, like for example activated carbon and biochar substances, are sustainable materials with great potential to be used in different technology applications. In this review, the following four applications were selected, and the works published in the last two years (since 2022) critically reviewed: agriculture; water treatment; energy management; and, carbon dioxide reduction and sequestration. GCM improved the performance of the technological applications under revision and play an important role in the sustainability of the processes, contributing to the mitigation of the climate change, namely by reducing emission and increase sequestration of CO2eq..

Measuring and predicting Carbon Emission (CE) is important to enabling the main culprit of various urgent environmental issues including global warming. However, prior studies did not fully incorporate the impact of micro-level urban streetscapes, which might lead to biased prediction of urban CE. To fill the gap, we developed an effective framework to predict residential CE in urban areas from widely existing and publicly available street-view images (SVI) using machine learning. First, we used a semantic segmentation algorithm to classify more than 30 streetscape elements from SVI images to describe the built environment whose features might affect residential and transportation CE. Second, based on the streetscapes quantified, we trained a 10-fold cross-validation method with various machine learning models to predict the CE at the 1KM grid level using CE data from the PlanetData. We found first, built environment features such as sidewalks, roads, fences, buildings, and walls are significantly correlated with the residential CE. Second, the presence of buildings and subtle streetscape features (e.g., walls, fences) indicates higher-density residential areas which are related to more residential CE. Third, vegetation (e.g., trees and grass) are reversely related to residential CE. Our findings shed light on the feasibility of using a single and open data source (i.e., the SVI) to effectively model neighborhood-level CE for regions across diverse urban forms. Our framework is useful for urban planners to inform new town development and urban regeneration towards the low CE goals.

In this paper, we present findings from a qualitative interview study, which highlights the difficulties and challenges with quantifying carbon emissions, and discusses how to move productively through these challenges by drawing insights from studies of deep uncertainty. Our research study focuses on the digital sector and was governed by the research question: how do practitioners researching, working or immersed in the broad area of sustainable digitisation (researchers, industry, NGOs, and policy representatives) understand and engage with quantifying carbon? Our findings show how stakeholders struggled to measure carbon emissions across complex systems, the lack of standardisation to assist with this, and how these challenges led stakeholders to call for more data to address this uncertainty. We argue that calls for more data to address this uncertainty obscure the fact that there will always be uncertainty, and that we must learn to govern from within it.

The spring-in phenomenon of the composite parts can affect the assembly process. This study aims to predict the spring-in phenomenon of carbon fiber reinforced plastic (CFRP) part. Here, we predict the spring-in of the CFRP part using a coupled analysis of the forming and cooling processes during the stamping process. First, a simulation of the entire forming process, such as the transfer of the composite laminate, gravity analysis, and forming was performed to obtain the temperature distribution of the CFRP part. Subsequently, a finite-element (FE) simulation of the cooling process was conducted to predict the spring-in phenomenon of the shaped CFRP part using the temperature data obtained in the forming simulation. Finally, a CFRP part was manufactured and compared with the results of the FE simulation.

In this paper, a novel nonlocal strain gradient anisotropic elastic shell model is developed to analyse the vibrations of simply supported single‒walled carbon nanotubes (SWCNTs). Sanders‒Koiter shell theory is used to obtain the strain‒displacement relationships. Eringen nonlocal elasticity theory and Mindlin strain gradient theory are adopted to derive the constitutive equations, where the anisotropic elastic constants are expressed via Chang molecular mechanics model. The complex variable method is used to analytically solve the equations of motion and to obtain the natural frequencies of SWCNTs. First, the anisotropic elastic shell model is validated via comparisons with the results of molecular dynamics simulations reported in the literature. Then, the effect of nonlocal and material parameters on the natural frequencies of SWCNTs with different geometries and wavenumbers is analysed. From the numerical simulations it is obtained that the natural frequencies decrease with increasing nonlocal parameter, while they increase with increasing material parameter. Moreover, the decrease of natural frequencies with increasing SWCNT radius is exponential as the material parameter increases, while it is linear as the nonlocal parameter increases. Finally, as the number of waves increases, the natural frequencies linearly vary with increasing nonlocal parameter, while they exponentially increase with increasing material parameter.

A new approach is presented for dynamic modeling of chemical and isotopic evolution of C1-3 during the hydrocarbon generation process. Based on systematic data obtained from published papers for pyrolysis of various hydrocarbon sources(type I kerogen/source rock, type II kerogen/source rock, type III kerogen/source rock, crude oil, asphalt, etc), the empirical evolution framework of chemical and isotopic composition of C1-3 during the hydrocarbon generation process was built. Although the empirical framework was built only by fitting large amount of pyrolysis data, the chemical and isotopic composition of C1-3 derived from the pyrolysis experiments all follow the evolution laws, convincing us that it is applicable to the thermal evolution process of various hydrocarbon sources. Based on the simplified formula of the isotopic composition of mixed natural gas at different maturities (δ13Cmixed) δ13Cmixed=(X〖*n〗_iA 〖*δ〗^13 C_iA+Y〖*n〗_iB 〖*δ〗^13 C_iB)/(X〖*n〗_iA+Y〖*n〗_iB ), it can be derived that the cumulative isotopic composition of alkane generated in certain maturity interval can be expressed by the integral of the product of instantaneous isotopic composition and instantaneous yield at certain maturity point, and then divided by the cumulative yield of alkane generated in corresponding maturity interval. Thus, the cumulative isotopic composition(A(X)), cumulative yield(B(X)), instantaneous isotope(C(X)),and instantaneous yield(D(x)) in the dynamic model comply with the following formula during the maturity interval of (X0-X) A(X)=(∫_(X_0)^X▒〖C(X)*D(X)dx〗)/(B(X)), where A(X) and B(X) can be obtained by fitting of pyrolysis data, and D(x) can also be obtained from the derivation of B(X). The dynamic model was applied on the pyrolysis data of Pingliang Shale to illustrate the quantitative evolution of cumulative yield ,instantaneous yield, cumulative isotope and instantaneous isotope of C1-3 with increasing maturity.The dynamic model can quantify the yield of methane, ethane and propane as well as δ13C1, δ13C2 and δ13C3 respectively during the hydrocarbon generation process, which is of great significance to evaluate the natural gas resources of hydrocarbon source rock with different maturity and to identify the origin and evolutionary process of hydrocarbons by chemical and isotopic data. Moreover, this model provides an approach to study the dynamic evolution of isotope series of C1-3 (including reversed isotopic series), which is hopeful to reveal the mechanism responsible for isotopic reversal when combined with post-generation studies.

Addressing the contemporary challenges of mitigating and adapting to climate change, conserving biodiversity, and ensuring human well-being constitutes a central focus for humanity. These challenges, though often treated in isolation, are intricately interconnected, sharing common drivers. Current and future research emphasizes the pursuit of an integrated approach that minimizes trade-offs and fosters synergies among the Sustainable Development Goals (SDGs). The nexus between ecosystem service value (ESV) and the social cost of carbon (SCC) is pivotal in informing national and governmental decisions regarding human well-being and climate change mitigation and adaptation, respectively. This study employs the Zhoushan Archipelago as a case study, exploring ESV and SCC dynamics from 2010 to 2020. An in-depth analysis of spatial development characteristics and the temporal and spatial correlation between ESV and SCC is conducted. The findings reveal an increase in Zhoushan Archipelago's land area from 2010 to 2015, stabilizing thereafter, with construction land exhibiting the most notable proportional growth. Carbon emissions were observed during the study period, with forests identified as the primary carbon sink, followed by mudflat and waterbody, while construction land contributed significantly to carbon emissions. Notably, the SCC in Zhoushan Archipelago increased by 2452%, contrasting with a modest 1.5% decrease in ESV during the study period. Global spatial correlation analysis demonstrated a significant positive correlation between ESV and SCC in Zhoushan Archipelago throughout the study period, validated by passing the P-value test. However, local spatial correlation analysis revealed a specific nature of the global spatial correlation between ESV and SCC in the island area. This nuanced understanding enhances our comprehension of the intricacies surrounding ESV and SCC dynamics, contributing valuable insights to the broader discourse on sustainable regional development, economic decarbonization, and human well-being improvement.

Due to the ever increasing global warming, the scientific community is concerned with finding immediate solutions to reduce or utilize carbon dioxide (CO2) and convert it in useful compounds. In this context, the reductive process of CO2 methanation is well investigated and attractive due to its simplicity. However, it requires the development of highly active catalysts. In this mini-review, the focus is on biochar-immobilized nanocatalysts for CO2 methanation. We summarize the recent literature on the topic, reporting strategies for the design of biochar with immobilized nanocatalysts and their performances in CO2 methanation. We review the thermochemical transformation of biomass into biochar and its decoration with CO2 methanation catalysts. We also tackle direct methods of obtaining biochar-nanocatalysts, in one pot, from nanocatalyst precursor-impregnated biomass. We review the effect of the initial biomass nature, as well as the conditions that permit to tune the perfomances of the composite catalysts. Finally, we discuss the CO2 methanation performances and how they could be improved keeping in mind low operation cost and particularly sustainability.

Gas turbine installations (GTIs) are widely used to generate electrical and thermal energy mainly by burning gaseous fuels. The use of GTIs to burn hydrogen as part of the development of hydrogen energy technology is currently of particular interest. In order to assess the prospects of using GTIs in such a way, it is necessary, among other things, to understand the carbon footprint of the gas turbine as part of the carbon footprint of the entire life cycle of hydrogen. The article provides an overview of the results of previously published studies on life cycle assessment (LCA) of technically complex devices associated with the production and consumption of fuel and energy, which, from the point of view of the complexity of LCA, are most similar to gas turbine installation. The characteristics of the considered stages and resources used in the assessment of the stages of the life cycle of technically complex equipment are presented, including an analysis of the amount of materials used in production and construction. Taking into account its specific application in Russia, an assessment of greenhouse gas emissions at the stages of the GTI life cycle per MWh of produced capacity was carried out.

The treasury of a DAO is purported to uphold the value of the DAO-issued token, and this study represents a pioneering effort to delve into these realms. We explore the relationship between the treasury and market capitalization in two DAO projects, namely Olympus DAO and KlimaDAO. Employing Granger Causality tests, we scrutinize the relationship between market capitalization and the treasuries of these DAOs. Furthermore, we use an EGARCH model to investigate the in-fluence of carbon offset tokens on KlimaDAO’s market capitalization, incorporating this variable into the model's conditional mean equation. The findings reveal a significant relationship between market capitalization and the treasuries of the DAOs, indicating a potential impact of market capitalization on treasuries. Additionally, the well-specified EGARCH model highlights the sig-nificance of carbon offset tokens, suggesting their potential to influence the overall market capi-talization of a DAO project and support its value.

Aluminum (Al) toxicity is the most common factor limiting the growth of alfalfa in acidic soil conditions. Melatonin (MT), a significant pleiotropic molecule present in both plants and animals, has shown promise in mitigating Al toxicity in various plant species. This study aims to elucidate the underlying mechanism by which melatonin alleviates Al toxicity in alfalfa through a combined physiological and transcriptomic analysis. The results reveal that 5 μM MT significantly alleviates Al-induced growth inhibition and preserves the morphology of root tip cells. Moreover, MT application reduces Al accumulation in alfalfa roots and shoots by 28.6% and 27.6%, respectively. Additionally, MT plays a crucial role in scavenging Al-induced excess H2O2 by enhancing the activities of superoxide dismutase (SOD), peroxidase (POD), and catalase (CAT), consequently reducing malondialdehyde (MDA) levels. The RNA-seq results reveal that MT application significantly upregulates the expression of xyloglucan endotransglucosylase/hydrolase (XTH) and carbon metabolism-related genes, including those involved in the glycolysis process, as well as sucrose and starch metabolism, suggesting that MT application may mitigate Al toxicity by facilitating the binding of Al to the cell walls, thereby reducing intracellular Al accumulation, and by improving respiration and the content of sucrose and trehalose. Taken together, our study demonstrates that MT alleviates Al toxicity in alfalfa by restoring redox homeostasis, enhancing Al binding to the cell wall, and modulating carbon metabolism. This research advances our understanding of the mechanisms underlying MT's effectiveness in mitigating Al toxicity, offering potential strategies for reducing Al accumulation in alfalfa.

For the territory of the Republic of Tatarstan (Russia), a spatial model of forest communities was built as a basis for assessing the sequestration potential of ecosystems. Combination of multi-temporal and multi-spectral satellite imagery from the Landsat 8 and Landsat 9 platform as input data and Google Earth Engine cloud platform were used. The set of 292 vegetation indices and metrics computed from the pre-processed imagery, were combined into dataset. The Weka X-Means clustering algorithm was trained and applied to study area. The unsupervised classification was carried out by vegetation classes in the Braun-Blanquet system. The results of unsupervised classification were verified using data from more than 17,000 relevés with geographic references from the Flora database. For automatic classification, the EuroVeg Checklist expert system in the JUICE 7.1 package was used. The proposed methodology for obtaining initial data and unsupervised classification, supported by an automated expert system, made it possible to obtain a picture of the vegetation distribution in the study area with sufficient accuracy, and in the future, it will be used to assess the sequestration potential of the ecosystems of the region under study.

The increading emission of carbon dioxide to the atmosphere has urged the scientific community to investigate alternatives to alleviate such emissions being the principal contributor to the greenhouse gas effect. One major alternative is carbon capture and utilisation (CCU) towards the production of value-added chemicals using diverse technologies. This work aims at the study of the catalytic potential of different cobalt-derived nanoparticels for methanol syntheis from carbon dioxide hydrogenation. Thanks to its abundance and cost-efficacy, cobalt can serve as an economical catalyst compared to noble-metal-based catalysts. In this work, we present a systematic comparison among different cobalt and cobalt oxide nanocomposites in terms of their efficiency as catalysts for carbon dioxide hydrogenation to methanol as well as how different supports can enhance their catalytic capacity. The oxygen vacancies in the cerium oxide act as carbon dioxide adsorption and activation sites, which facilitates a higher methanol production yield.

We present atomic structures and nonequilbrium synthesis of new class of materials, where the basic structural unit is a diamond tetrahedron. When units of one, two, and three tetrahedra are randomly packed, we create distinct phases of amorphous Q-carbon. Four tetrahedra in two adjacent layers lead to crystalline diamond lattice, which has four missing tetrahedra alternately. When these four missing tetrahedra are filled, we create subunit cell of crystalline Q-diamond. Theoretical calculations show that superconducting transition temperature (Tc) in 50 atomic % B-doped Q-diamond can reach near room temperature at ambient pressures. This is consistent with our earlier results using low-loss EELS measurements in 50 atomic % B-doped Q-carbon, which had mostly amorphous QB3 phase mixed with some crystalline Q-diamond phase. These EELS results showed that the Tc for these samples was in between 90K and 300K. Theoretical calculations of density of states, Eliashberg function, electron-phonon interaction parameter, and root-mean-square and logarithmic average of frequency in crystalline Q-diamond show Tc in the range of 268K to 300K, which is in a complete agreement with our EELS results in QB3.

In this study, we report the antibacterial mechanisms of action of uniform silver nanoparticles (AgNPs) and decorated activated carbon nanocomposite (CAC-AgNPs) obtained using a green synthesis approach. The nanomaterials were characterized by ultraviolet-visible (UV-vis) absorption spectra and Fourier transform infrared (FTIR) spectra. The antibacterial activity of the as-prepared nanomaterials was evaluated against an array of bacterial strains by microdilution method, whereas their cytotoxicity profile was evaluated on Vero cells (human mammalian cells). The antibacterial mechanistic studies of active nanomaterials were carried out through bacterial growth kinetics, nucleic acid leakage test, and catalase inhibition assay. A silver nanocomposite was successfully fabricated from Croton macrostachyus-based activated carbon. The as-prepared nanomaterials exhibited antibacterial activity against an array of bacterial strains (minimum inhibitory concentration (MIC) range: 62.5 to 500 µg/mL), the most susceptible being Escherichia coli and Staphylococcus aureus. Cytotoxicity studies of the nanomaterials on Vero cells revealed that the nanocomposite (median cytotoxic concentration (CC50): 213.6 µg/mL) was less toxic than the nanoparticles (CC50 value: 164.75 µg/mL) counterpart. Antibacterial mechanistic studies unveiled that the nanomaterials induced (i) bacteriostatic activity vis-à-vis E. coli and S. aureus and (ii) inhibition of catalase in these bacteria. This novel contribution on the antibacterial mechanisms of action of silver nanocomposite from C. macrostachyus-based activated carbon might contribute to the understanding of antibacterial action of these biomaterials. Nevertheless, more chemistry and in vivo experiments, as well as in depth antibacterial mechanistic studies are warranted for the successful utilization of these antibacterial biomaterials.

In this study, ignition delay and burning rate are experimentally investigated in relation to the effect of pristine carbon nanotubes (CNTs), sodium dodecylbenzene sulfonate (SDBS), and diesel blends. Single droplet combustion tests were conducted in a combustion system for 21 days using CNTs at concentrations of 50 ppm and 100 ppm, that were dispersed in Colombian commercial diesel and stabilized by SDBS. Additionally, recordings of the combustion were collected, and the Shadowgraph optical method was utilized for monitoring the evolution of droplet size during combustion. The measurements were done over a four-week period. The results demonstrated that the temporal stability has a direct impact on the single droplet combustion tests because a concentration of CNTs of 100 ppm showed higher stability than those achieved by 50 ppm. Consequently, improvements were found with a concentration of 100 ppm, for instance, thermal conductivity increased by about 20%, ignition delay time by 16.2%, and burning rate by 30.5%.

The Limpopo estuary mangrove forest covers about 928 ha, however 382 ha remain intact and 546 ha were degraded after the 2000 floods. Mangrove replanting campaigns have been carried out at the site. This article aims to evaluate the structure and carbon pool of aboveground and belowground living biomass and soil carbon in natural and replanted mangrove forests (2016, 2014 and 2010). The methodology consisted of selecting 40 strata where structural data were collected. Living biomass above and below ground and soil carbon was obtained based on the methodology described by Kauffman and Donato (2012). The results showed that A. marina was the most observed species in all study areas. The carbon reserve of living biomass above and below ground in the natural forest was 67.9±100.9 MgCha -1 and 65.0±77.1MgC ha -1 , respectively; and in the planted forests (2016, 2014, 2010) it was 1.1±0.5MgCha-1 and 2.1±1.0MgCha-1, 1.8±1.0MgCha-1 and 3.6±2.0MgCha-1, 3.7±2.0MgCha-1 and 5.3±2.5MgCha-1 . Soil carbon reserve was 229.4±119.4 MgCha-1 in natural forest and 230.3±134.8 MgCha-1 , 234.8±132.7MgC ha-1, 229.4±119.4 MgCha-1 in planted forests (2016, 2014, 2010). The total carbon reserve in the natural forest was 362.3 MgCha-1 and in the planted forestsn(2016, 2014, 2010) it was 233.5 MgCha-1 , 240.2 MgCha-1, 246.4 MgCha-1. Natural and restored forests had similar anoumts of soil carbon, which reinforces the idea that soil is a stabel carbon pool. Morever, restored forests failed to store the same amount of live biomass (an carbon), which supports the idea that it is better to prevent habitat degradation than to restore it.

Abstract: This study observes the characteristics and influencing factors of carbon fluxes of the Momoge salt marsh ecosystem over four years, which behaves as a CO2 sink. The daily, seasonal, and interannual variations of CO2 fluxes in the Momoge salt marshes were observed using the eddy covariance method and compared with various environmental factors. An overall daily “U” shaped distribution was observed, with uptake during the day (negative values) and release at night (positive values). Annually, the carbon fluxes in the study area roughly exhibit a “V” shape. Carbon fluxes during the non-growing season predominantly showed positive values, indicating the release of CO2 into the atmosphere. Photosynthetically active radiation was the primary influencing factor affecting hourly and daytime variations in net ecosystem exchange (NEE) during the growing season, while temperature was the main factor influencing nighttime NEE dynamics. Air temperature, soil temperature, photosynthetically active radiation, precipitation, and water level all had significant impacts on daily net CO2 exchange. At the monthly scale, larger values of soil temperature, air temperature, photosynthetically active radiation, and aboveground biomass correspond to a stronger carbon absorption capacity of the ecosystem. Overall, temperature remains the primary factor for carbon fluxes in the Momoge wetlands.

Freshwater lakes represent a potential source of methane (CH4) to the atmosphere. However, the CH4 emission contribution to the total emission in the littoral zones of lakes, especially emergent macrophytes (e.g., lotus), are poorly known. Lotus, has been cultivated in almost all provinces in China, is not only an aquatic plant but also a kind of vegetables. Two sampling zones (lotus plant and open water) were established in the lake of the middle reaches of Yangtze River. The CH4 emission was measured using a floating opaque chamber and gas chromatography between April to December of the years 2021 and 2022. The results indicated that the flux of CH4 emissions ranged from 0.10 to 59.75 mg m-2 h-1, with an average value of 5.61 mg m-2 h-1 in the open water, while ranged from 0.19 to 57.32 mg m-2 h-1, with an average value of 17.14 mg m-2 h-1 in the lotus plant zone. The maximal CH4 emissions occurred in July and August for the open water, which was highly related to the air and water temperature; whereas it happened in September for the lotus plant zone, due to the fresh organic matter inputting to sediments, CH4 transportation by lotus plant, high soil organic carbon content, and the lower dissolved oxygen concentration. Considering the carbon emissions (both CH4 and CO2) and plant productivity, although the greater CH4 emission occurring in lotus plant zone, it could still represent a potential carbon sink (213 g m-2 yr-1), compared to the open water.

The operating theatre represents a key contributor to healthcare-derived emissions. Here, we outline the carbon footprint of a lumbar microdiscectomy at our regional unit in Greater Manchester, with the use of AI technology. In doing so, we aim to define the extent of the environmental impact and identify carbon hotspots for sustainable change. Our unit of analysis covered the start of the patient journey into hospital through to the final outpatient appointment. Publicly available and locally sourced data was used. An inventory analysis of two lumbar microdiscectomies was conducted. Each item was categorised reconciled against our AI-powered ‘CO2 analysis’ database. Kilograms of carbon dioxide equivalent (kg CO2e) was chosen as the primary measure of impact. An average lumbar microdiscectomy at our trust generates 477.73kg CO2e. The operation (173.89kg CO2e, 36.40%) and the inpatient stay (144.67kg CO2e, 30.28%) constituted the biggest contributors. Single-use intraoperative equipment contributed to over three-quarters of the total emissions from the operation. By defining the environmental burden of elective spinal surgery, we have identified carbon hotspots to target for sustainable change. Substituting polluting elements for carbon-friendly alternatives and challenging the single-use culture, modern healthcare systems can help pave the way to a ‘net zero’ healthcare system.

During shearer operation, piston rod is susceptible to wear from invasion of pollutants, and then ruins sealing ring in hydraulic cylinder. This work attempts to conduct a systematical investigation of Cu-DLC (Cu-doped Diamond-like Carbon) film to improve the seal performance. Failure process of hydraulic cylinder was analyzed, and relevant parameters were determined. Several Cu-DLC films were deposited on the substrate of piston rod in a multi-ion beam assisted system, and their structures and combined tribological performances were investigated. As a result, dust particles attached to the piston rod may enter the cylinder, and damage the sealing ring under the radial force. Cu grains prefer to orientate (111) crystal plane with increase of Cu content, and may induce drop of hardness and internal stress for the film. Friction coefficient of the film ranges from 0.04 to 0.15, and rise of IG/ID ratio from 1.4 to 2.3 in Raman data indicates that bond transition from sp3-C to sp2-C may lower the friction coefficient. Modification mechanism of Cu-DLC film for the seal performance may come from synergistic effects of (i) contact force and friction heat induce the film graphitization, (ii) Cu doping improves toughness of the film and acts as a solid lubricant, and (iii) transfer layer plays a role of self-lubrication.

As an important organelle in eukaryotic cells, Golgi apparatus is responsible for processing and transporting proteins and lipids in cells. Precise monitoring the status of Golgi apparatus by targeting fluorescence imaging technology is of enormous importance but remains an attractive yet dramatically challenging task. In this study, we report the construction of the first Golgi apparatus targeted sensor with bright near-infrared fluorescence, termed as Golgi-Pdots. As a start point of our investigation, hydrophobic CDs with bright NIR fluorescence at 674 nm (fluorescence quantum yield : 12.18%), narrow emission band of 23 nm, and excellent stability were facilely prepared from Magnolia Denudata flowers through an ultrasonic method. Incorporating the CDs into a polymer matrix modified with Golgi-targeting molecules can produce the water-soluble Golgi-Pdots, which showed high colloidal stability and similar optical properties as compared to CDs. Further studies revealed that the Golgi-Pdots showed good biocompatibility and Golgi-targeting ability. Based on these fascinating properties, Golgi-Pdots have been successfully used for long term bioimaging of Golgi apparatus inside live cells.

Developing nanomaterials with the capacity to restrict the growth of bacteria and fungus is of current interest. In this study, nanocomposites of poly(2-hydroxyethyl methacrylate) (PHEMA) and carbon nanotubes (CNTs) functionalized with primary amine, hydroxyl, and carboxyl groups were prepared, and characterized. An analysis by Fourier transform infrared (FT-IR) spectroscopy and X-ray photoelectron spectroscopy showed that PHEMA chains were grafted to the functionalized CNTs. The morphology of the prepared nanocomposites studied by field emission scanning electron microscopy (FE-SEM), and transmission electron microscopy (TEM) shows significant changes with respect to the observed for pure PHEMA. The thermal behavior of the nanocomposites studied by differential scanning calorimetry (DSC) revels that the functionalized CNTs affects strongly the mobility of the PHEMA chains. Tests carried out by thermogravimetric analysis (TGA) were used to calculate the degree of grafting of the PHEMA chains. The ability of prepared nanocomposites to inhibit the growth of the fungus Candida albicans, and the bacteria Staphylococcus aureus, Pseudomonas aeruginosa, Escherichia coli was evaluated. A moderated antifungal and antibacterial capacity of the prepared nanocomposites was determined.

Bisphenol A is a remarkable chemical compound for its many applications mainly in the plastics industry, but also for its toxic effects on the environment and human health. BPA (4,4-isopropylidenediphenol) is an anthropogenic compound, moderately soluble in water (120 – 300 mg/l) at room temperature, and highly soluble in alkaline solutions, ethanol and acetone. BPA can bioconcentrate, bioaccumulate and biomagnify through food webs until it reaches humans. To prevent this, effective strategies are sought to allow its removal from the environment, through physico-chemical or enzymatic methods, advanced oxidation, adsorption and biodegradation, ultrasonic degradation. This article shows a comparative study regarding adsorption of BPA on Active carbon and zeolitic tuff, ZTC. In this paper, the characterization of the zeolitic tuff Rupea adsorbent, was carried out from an elemental and mineralogical point of view, pore size and elemental distribution, using SEM, EDAX, and XRD analysis. The pore size varies from 30 nm to 10 µm, atomic ratio Si/Al≥4, and the 80 % of mineralogical composition represent Ca Clinoptilolite zeolites Ca Clinoptilolite zeolite ((Na1.32K1.28Ca1.72Mg0.52)(Al6.77Si29.23O72)(H2O)26.84). Also, a comparative study of the adsorbtion capacity of bisphenol A from synthetic solutions on activated carbon type - Norit GAC 830 W, GAC, as well as on Clinoptilolite-type zeolitic tuff, ZTC, Rupea, was carried out. The experiments were carried out at a temperature of 20 ºC, a pH of 4.11; 6.98 and 8.12, and ionic strength being assured using KCl of 0.01 M, and 0.1 M. The adsorption capacities of GAC and ZTC tend to 115 mg/g and 50 mg/g respectively, at 8.12 pH and ionic strength of 0 M. The Langmuir mathematical model most faithfully describes the adsorption equilibrium of BPA. The maximum adsorption capacity for both adsorbents increases with increasing pH, and decreases with increasing ionic strength.

The design and fabrication of low-cost catalysts for highly efficient oxygen reduction is of paramount importance for various renewable energy-related technologies, such as fuel cells and metal-air batteries. Herein, we report the in situ growth of Fe3N nanoparticles encapsulated N-doped carbon nanotubes on the surface of flexible biomass-derived carbon cloth (Fe3N@CNTs/CC) via a simple one-step carbonization process. Taking advantage of its unique structure, Fe3N@CNTs/CC was employed as a self-standing electrocatalyst for oxygen reduction reaction (ORR) and possessed high activity as well as excellent long-term stability and methanol resistance in alkaline media. Remarkably, Fe3N@CNT/CC can directly play the role of both gas diffusion layer and electrocatalytic cathode in a zinc-air battery without additional means of catalyst loading, and display higher open circuit voltage, power density, and specific capacity in comparison with the commercial Pt/C catalyst. This work is anticipated to inspire the design of cost-effective, easy-preparation, and high-performance air electrodes for advanced electrochemical applications.

Hydrogen has been considered a future energy carrier for decades and the demand for hydrogen in refineries is always upward due to the revival of new technologies. The steam methane reforming method is frequently employed because of its high hydrogen generation efficiency at a cheap cost and minimal negative impact on the environment. But depending on the type of feedstock, one unit of hydrogen generate 9-10 units of CO2 that is needed to be treated for environmental sustainability. Therefore, the optimization of hydrogen production and CO2 capture is very important to address. The simulation research was conducted to anticipate and optimize steam reforming using Aspen HYSYS. A conversion-type reactor was used to develop this simulation-based model. The primary goal of this work is to investigate and optimize the production efficiency of hydrogen and the mitigation of CO2 that is generated from the steam reforming process by varying process parameters. CO2 capture efficiency was investigated at the different yields for hydrogen production and was found that a maximum of 98.8% of the CO2 can be absorbed using the proposed carbon capture system. Later, the Aspen Energy Analyzer tool revealed potential improvements for energy and cost optimization.

Mercury emissions from small-scale coal-fired boilers are still a serious environmental problem in Poland and the Czech Republic. The publication presents the results of mercury emission tests conducted using five different small-scale coal-fired boilers and five different coal fuels. The research was carried out under laboratory conditions, but also using residential users' heating devices. They covered a wide range of operational parameters, both energy and emission. It was shown that more than 94% of the mercury contained in coal fuel undergoing combustion is emitted into the atmosphere with the volatile products of combustion (including dust), and the amount of emissions is strongly dependent on the original mercury content of the fuel. One solution to the problem of mercury emissions from small-scale coal-fired boilers may be to replace traditional coal with low-emission carbon fuels. The paper shows that mercury emissions from burning such fuels are many times lower than from burning coal. The widespread use of low-emission carbon fuels in individual heating systems in Poland and the Czech Republic would reduce mercury emissions to the atmosphere by up to 90% compared to the current level of emissions generated by individual heating systems in these countries.

In the present study, the ability of novel carbon microspheres (CMs) derived from a date palm (Phoenix dactylifera) biomass using a hydrothermal carbonization (HTC) process and activated using phosphoric acid in removing methylene blue dye was investigated. Three types of palm-based wastes (seeds, leaflet and inedible crystallized date palm molasses) were used and converted to CMs via HTC process. The prepared samples were then activated using phosphoric acid via incipient wetness impregnation method. The CMs samples before and after activation were analyzed using scanning electron microscopy (SEM), elemental analysis and scanning (CHNS), Fourier Transform-Infrared (FTIR) and Brunauer–Emmet–Teller (BET) method. The samples exhibited high BET surface areas after activation (1,584 m2/g). The methylene blue adsorption results showed good fittings to the Langmuir and Redlich-Peterson isotherm models for all activated samples. The maximum adsorption capacity achieved was 409.84 mg/g for activated CM obtained from the palm date molasses, indicating high potential for application as dye-based adsorption materials.

Abstract: Based on the survey data of 5 large grain-producing provinces in China, this paper studies the effect of agricultural production trusteeship on agricultural carbon emission reduction by using a propensity score matching method. The empirical results show that the carbon emission of wheat reduces by 7.107kg/mu, with a decrease rate of 15.5% after participating in agricultural production trusteeship. Among them, chemical fertilizers, manpower input, agricultural chemicals and diesel oil respectively reduces with rates of 14.2%, 27.7%, 14.1%, and 6%. However, there are differences in the facilitation effects of different trusteeship services, with the best promotion effect of field management services, followed by cultivation, planting and harvest services, and then agricultural material supply services, the ATT is -6.160, -5.732 and -5.530, respectively. Meanwhile, there are differences in the promotion effects for farm households with different factor endowments. The promotion effect is better for small farm households with 1 type of agricultural machinery or less, and an operation scale of 7 mus or less. Therefore, in order to better play the role of agricultural production trusteeship on agricultural carbon emission reduction, the government should vigorously support its development and guide more smallholders to choose agricultural production trusteeship.

The possibility of increasing the resource of steel fingers working in tandem with bronze bushings by plasma-electrolytic nitrocarburizing of the surface of medium carbon steel is shown. The phase composition, microhardness, morphology and surface roughness were studied. Tribological tests were carried out under dry friction conditions according to the shaft-pad scheme. It has been established that plasma-electrolytic nitrocarburizing of the surface of medium carbon steel at a temperature of 700 °C for 5 minutes leads to a decrease in a friction coefficient by 2.3 times, weight wear of steel by 24.9 times, and bronze counterbody by 5.9 times. At the same time, the contact stiffness increases 2.6 times. The type of wear is fatigue with dry friction and plastic contact. Changes in tribological characteristics are associated with the high hardness of the hardened steel surface together with the influence of dispersed nitrides and iron carbonitrides distributed in it.

All solar thermal systems, due to their thermal nature, can be hybridised or operated with both fossil fuel and solar energy. By enhancing availability and dispatch ability, hybridization has the potential to boost the value of concentrating solar thermal technology. Hybrid photovoltaic thermal systems (PV/T) offer a solution to improve on the limited capacity growth seen with standard solar panels. The analysis focuses on the creation of alternative structural and design so-lutions that may be used to boost lacking efficiency that was previously hampered by limited spectrum absorption of sun light. As a result, the spectrum is separated into two spectrum ranges, one that directly matches the bandgap of PV materials and the other that is absorbed for thermal absorption outputs. Most two channel systems are used to capture or reflect sunlight, with the layer specifically located right above the PV cell. Another layer of nanofluid is employed to evacuate heat from the PV cell, acting as the second channel, to specifically eliminate overheating difficulties. To address concerns that have arisen as a result of years of observation, the most recent study involves nano-particle-based fluids employed in PV/T, which uses a cooling medium to provide an alternate heat transfer option. Aside from nanofluids, there are phase change materials, channel alterations that result in a higher flow rate and hence improve overall performance.

Ribosomal proteins (RPs) mediate protein synthesis and stability of the ribosomal complex. RPs and rRNA form ribosomal subunits and ri-bosomes, the cellular machinery for protein synthesis, a fundamental biological process related to cell growth and proliferation. The differ-ences between paralogs within the same RP family have led them to ac-quire extraribosomal functions involved in plants' growth, develop-ment, and biotic and abiotic stresses. From transcriptomic analysis, it has been revealed that ribosomal proteins have a crucial role during MTs development. The RPLs; RPL11, RPL29 and RPL40 interact with PEBP family members (Phosphatidylethanolamine-binding proteins), poten-tial activators in the MTs development. In potatoes, genome editing is a promising technology to introduce crop breeding traits. Recently, the edition of the genome through the CRISPR/Cas9 system has made it the most efficient and powerful genetic modification method. Based on this, the gene modulation by overexpression and silencing in RPL11, RPL29 and RPL40 will guide us to understand the effect on the microtuberiza-tion process and produce improved potato plants with the capability of growing under adverse environments (biotic and abiotic stresses). By understanding the molecular biology mechanisms that RPs govern, we can improve crops under today's changing climatic conditions.

The issue of environmental sustainability is increasingly topical and one of the most impactful sectors is that of the construction industry. As stated in the reports of the GlobalABC, the building sector is the main responsible for GHG emissions, generating about 37% of global CO2e emissions. Already during the phases of production and construction of buildings about 10% of global emissions are produced, while the remaining part comes from their use, from the energy for air conditioning and lighting. Reducing emissions in the pre-use phase of buildings is therefore a crucial issue for combating climate change. The research investigates the potential of timber construction systems, thanks to the carbon storage property of the material. The proposed calculation methodology is structured according to the LCA-Life Cycle Assessment approach, referring to the C2H phase (from Cradle-To-Handover), and evaluates emissions related to the production and construction of buildings. To identify the timber construction system that minimizes CO2e emissions, within the limits of the investigation (A1-A5 phases), the method was applied to two buildings built with different technologies: one with X-Lam panels and one with a framed structure. The results were analyzed, compared, and discussed to demonstrate that the timber buildings are the most virtuous solution in the Net Zero Carbon perspective by 2050.

The main objective of this work is to study the effects of carbon nanotubes (CNT) on the strength and electrical properties of cement mortar. Molecular dynamic simulations (MDS) were carried out for the mechanical and electrical properties of the cementitious composite and the associated mechanisms. To model the atomic structure of the Calcium-Silicate-Hydrates (C-S-H) gel, tobermorite 11Å was chosen. Single-walled carbon nanotubes (SWCNTs) embedded in tobermorite structure were tested numerically. In particular, the effect of the concentration of CNT in cement paste was studied. An innovative experiment of electrical characterization of a cementitious composite of carbon nanotubes has been developed.

This study examines whether and how carbon trading policy impacts the financialization of non-financial firms, using China emission trading scheme as a natural experiment. We show that the carbon trading policy has effectively long-term inhibitory effect on corporate financialization. Our findings are robust to possible result bias and more precise control group. In addition, we explore potential channels through which carbon trading policy can affect financialization, and find that it contributes to curb financialization by reducing financing constraints. Finally, we show that the relationship between carbon trading policy and financialization of non-financial companies is moderated by company’s ownership, region and industry competition.

A nonlinear MEMS multimass sensor is investigated. The MEMS design consists of an array of nonlinear microcantilevers clamped to a shuttle mass which, in turn, is attached to a linear spring and a dashpot. The microcantilevers are made of a polymeric hosting matrix reinforced by aligned carbon nanotubes (CNT) with different CNT volume fractions in each cantilever so as to suitably tune the frequency bandwidth of the device. The advantages of a single input-single output (SISO) system are here exploited for the design, actuation and detection principles as in previous literature.

Multiwalled Carbon Nanotubes (MWCNTs) is more efficient for fabrication modern design of silicone rubber (SR) that used in industrial engineering applications; it has been embedded in room temperature vulcanization silicone rubber (RTV-SR) matrix for controlling in dielectric characterization. Frequency dielectric measurements were performed for multiwalled carbon nanotubes SR/MWCNT nanocomposites. Hence, the dielectric properties of modern design SR/MWCNT nanocomposites has been deduced as experimental work done to clarify the benefit of filling MWCNT with different patterns inside dielectrics. In variant thermal conditions (up to 40oC), it has been investigated that the new behaviors of SR/MWCNT nanocomposites dealing with nanotechnology techniques for designing new dielectric behaviors of insulation materials. Finally, this research succeeded to characterize dielectric constant, electric modulus and dielectric loss of SR/MWCNT nanocomposites with respect to traditional silicon rubber under variant thermal conditions and frequency response analysis (FRA) according to using certain types and concentrations of MWCNTs.

The Chinese government has expressed great confidence in the role of green finance in fulfilling its carbon neutrality commitment. However, the effectiveness of green finance, especially under the impact of emergencies such as the COVID-19 pandemic scenario, requires further examination. Using data from 2000 to 2020 in China, the correlation between green finance and carbon dioxide (CO2) emissions has been analyzed, both in BaU scenario and the COVID-19 scenario. The following conclusions were drawn: (1) In BaU scenario, green finance can effectively reduce CO2 emissions, especially through government green expenditure and green credit; (2) In COVID-19 scenario, although there is no direct relationship between the pandemic and carbon emissions, the data shows that the pandemic has hindered the progress of green finance, weakened its ability to curb carbon emissions, and indirectly led to an increase in carbon emissions. This study not only clarifies the mechanism by which the COVID-19 pandemic affects carbon emissions through the green finance system but also addresses the common problem of data scarcity in green finance research.

In the present paper, the comparison is conducted between three classical shell theories as applied to the linear vibrations of single-walled carbon nanotubes (SWCNTs); specifically, the evaluation of the natural frequencies is conducted via Donnell, Sanders and Flügge shell theories. The actual discrete SWCNT is modelled by means of a continuous homogeneous cylindrical shell considering equivalent thickness and surface density. In order to take into account the intrinsic chirality of carbon nanotubes (CNTs), a molecular based anisotropic elastic shell model is considered. Simply supported boundary conditions are imposed and complex method is applied to solve the equations of motion and to obtain the natural frequencies. Comparisons with the results of molecular dynamics simulations available in literature are performed to check the accuracy of the three different shell theories, where Flügge shell theory is found to be the most accurate. Then, a parametric analysis evaluating the effect of diameter, aspect ratio and number of waves along the longitudinal and circumferential directions on the natural frequencies of SWCNTs is performed in the framework of the three different shell theories. Assuming the results of Flügge shell theory as references, it is obtained that Donnell shell theory is not accurate for relatively low longitudinal and circumferential wavenumbers, for relatively low diameters and for relatively high aspect ratios. On the other hand, it is obtained that Sanders shell theory is very accurate for all the considered geometries and wavenumbers, and therefore it can be correctly adopted instead of the more complex Flügge shell theory for the vibration modelling of SWCNTs.

Due to its high specific surface area and rich porous structure, acacia-derived porous activated carbon is the most potentially effective material for wastewater treatment. This research study aimed to prepare activated carbon using Acacia erioloba seedpods as carbonaceous materials and phosphoric acid as an activating agent. The specific surface area of the prepared activated carbon sample was characterised by Brunauer–Emmett–Teller instrument. The specific surface area value was 387 m²/g. The activated carbon prepared was then sieved into three different particle sizes of 50, 100 and 200 micrometres and characterised using various analytical procedures, including proximate analysis to study moisture content, ash content, volatile matter content and fixed carbon content. The bulk density, SEM, power of hydrogen, iodine number and methylene blue number index were also investigated to determine the adsorption properties of the prepared activated carbon. Batch adsorption dynamics for the removal of organic compounds such as methylene blue and unsaturated character of fatty acid from aqueous solution were also carried out at room temperature to evaluate the prepared activated carbon's applicability in water treatment. The iodine number was 528, 638, and 554 mg/g for the 50, 100, and 200 μm activated carbon particles, respectively. From the results, the adsorption of methylene blue favoured the Freundlich adsorption model, showing higher correlation (R²) values than the Langmuir model. The results indicate that methylene blue particles were adsorbed on heterogeneous surfaces.

Lithium-ion batteries (LIBs) have become the preferred battery system for portable electronic devices and transportation equipment because of their high specific energy, good cycling performance, low self-discharge and no memory effect. However, too low ambient temperature will seriously affect the performance of LIBs, almost cannot discharge at -40~-60 ℃. There are many factors affecting the low temperature performance of LIBs, among which the electrode material is an important factor. Thus it is urgent to develop electrode materials or modify existing materials with excellent low temperature LIBs performance. Carbon-based anode is a kind of LIBs candidate. In recent years, it has been found that the diffusion coefficient of lithium ion in graphite anode decreases more obviously at low temperature, which is one of the important bottlenecks limiting its low temperature performance. However, the structure of amorphous carbon materials is complex, amorphous carbon materials have good ionic diffusion properties, and its grain size, specific surface area, layer spacing, structural defects, surface functional groups and doping elements may have a greater impact on the low temperature performance of the material. In this work, the low temperature performance of LIBs is obtained by modifying the carbon-based material from the perspective of electronic modulation and structural engineering.

Heterojunctions based on metal halide perovskites (MHPs) are promising systems for photocatalytic hydrogen evolution reaction (HER). In this work, we coupled Cs3Bi2Br9 nanocrystals (NCs), obtained by wet ball milling synthesis, with g-C3N4 nanosheets (NSs) produced by thermal oxidation of bulk g-C3N4 in air. These methods are reproducible, inexpensive, and easy to scale up. Heterojunctions with different loadings of Cs3Bi2Br9 NCs were fully characterized and tested for HER. A relevant improvement of H2 production with respect to pristine carbon nitride was achieved at low NCs levels reaching values up to about 4600 µmol g-1 h-1. This work aims to provide insights on the synthesis of inexpensive and high performing heterojunctions using MHP for photocatalytic applications.

Palm oil production involves unit operations that lead to greenhouse gas emissions. A typical mill is estimated to produce greenhouse gas emissions of 637–1,131 kg CO2 eq/t crude palm oil. There has been a huge effort to reduce the carbon footprint of palm oil mills. However, the data from such research have not been consolidated. This paper reviews significant information, results, and conclusions derived from studies in the literature. The latest developments in palm oil milling operations and information on greenhouse gas emissions are presented. Current initiatives in reducing carbon footprint of palm oil mills are discussed along with an assessment of the technologies employed. These include the conventional method of capturing biogas from palm oil mill effluent and emerging approaches such as converting palm sludge oil into biodiesel, deploying enzyme-assisted oil extraction, and converting biomass into fuel for energy generation as an alternative to coal and other fossil fuels. The importance of self-sufficiency is deliberated because a self-sufficient palm oil mill is estimated to reduce emissions by 457 kg CO2 eq/t crude palm oil compared to a mill that requires an external power supply. Methods with the greatest positive effect on the carbon footprint are identified for further investigation.

Silver iodide (AgI) is a system prototype allowing the flow of ions through its structure and has a phase transition at 420 K, characterized by an abrupt change in conductivity and a high ionic conductivity. Introducing low concentrations of graphite (C) into the AgI structure produces a new material with a mixed conductivity (ionic and electronic) which increases with increasing temperature. The experimental results of the logarithm of the ionic conductivity as a function of the inverse of temperature for the (AgI)x–C(1−x) system for low carbon concentrations 0.97 ≤ x ≤ 0.99 were well fitted using a phenomenological model with a probability distribution for the charge carriers based on the carrier density

L-asparaginase (ASNase) is an aminohydrolase currently used in the pharmaceutical and food industries. Enzyme immobilization is an exciting option for both applications, allowing a more straightforward recovery and increased stability. High surface area and customizable porosity make carbon xerogels (CXs) promising materials for ASNase immobilization. This work describes the influence of contact time, pH, and ASNase concentration on the immobilization yield (IY) and relative recovered activity (RRA) using Central Composite Design methodology. The most promising results were obtained using CX with an average pore size of 4 nm (CX-4), reaching IY and RRA of 100%. At the optimal conditions, the ASNase-CXs biocomposite was characterized and evaluated in terms of kinetic properties and operational, thermal and pH stabilities. The immobilized ASNase onto CX-4 retained 71% of its original activity after six continuous reaction cycles, showed a good thermal stability at 37 °C (RRA of 91% after 90 min) and was able to adapt to both acidic and alkaline environments. Finally, the results indicated a 3.9-fold increase in the immobilized ASNase affinity for the substrate, confirming the potential of CXs as a support for ASNase and as a cost-effective tool for subsequent use in the therapeutic and food sectors.

The role of agroforestry systems in providing ecosystem services is very crucial. The most significant increase in carbon (C) storage is often achieved by moving from lower biomass land-use systems to tree-based systems like agroforestry (AF). However, estimation of carbon stocks in indigenous agroforestry systems of South-eastern Rift- valley landscapes, Ethiopia the data are scarce. The study was aimed to investigate the biomass, biomass carbon (BC), and soil organic carbon (SOC) stock of Enset based, Enset-Coffee based, and Coffee-Fruit tree-Enset based agroforestry systems. Comparison of SOC stock of agroforestry systems against their adjacent monocropping farms was also investigated. The study was conducted in three selected sites of the Dilla Zuria district of Gedeo zone. Twenty farms (total of 60) representative of each AF system were randomly selected, inventoried and biomass C stocks estimated. Ten adjacent mono-cropping farms which were related to each AF system were selected in a purposive manner for comparison of SOC stock. Inventory and soil sampling were employed in the 10×10 m farm plot. The mean aboveground biomass ranged from 81.1 t ha-1 to 255.9 t ha-1 and for belowground biomass from 26.9 t ha-1 to 72.2 t ha-1. The highest C stock was found in Coffee-Fruit tree-Enset based (233.3±81.0 t ha-1), and the lowest was in Coffee-Enset based agroforestry system (190.1±29.8 t ha-1). The result showed that SOC stocks were not statistically significant between the three AF systems, although they showed a significant difference in their BC stock. The AF systems' C stocks are substantially higher than those reported for tropical forests and other AF systems. The SOC of AF systems was significantly higher than the ones for the adjacent monocropped farms. Therefore, it is possible to deduce that AF systems are storing significant amount of C and contributing to climate change mitigation.

Agricultural mechanization is an important factor to improve the green total factor productivity of planting industry, which is the key way to realize the sustainable development and high-quality development of agriculture. Based on the panel data of 30 provinces in China from 2001 to 2019, this paper uses the stochastic frontier analysis method of output oriented distance function to measure the green total factor productivity of China’s planting industry based on net carbon sink, and empirically studies the impact of agricultural mechanization on the green total factor productivity in China’s planting industry. The empirical analysis finds that mechanization can significantly promote the planting green total factor productivity, and this basic conclusion is still robust after using instrumental variables, sub sample regression. Further research found that the path of mechanization on planting green total factor productivity is mainly reflected in technology progress and spatial spillover. The mechanism of operation scale expansion, factor allocation optimization and technical efficiency change is not significant. Given these findings, the paper adds considerable value to the empirical literature and also provides various policy- and practical implications.

Environmental tax is the climate policy that offers, in theory, the easiest way for carbon reduction. But in practice, implementation has proven complicated despite public demand for policy action on climate change. This research investigates to reframe environmental taxes in ways more personally engaging to create a moral foundation, and massive participation. As people show rising demand, we aimed to design a tool that responds to public expectations and operates directly at source on emission reducers, viz the trees. Drawing on research from environmental taxes and the evidence of measures taken, we reasoned that an environmental fiscal policy may not intend necessarily to punish the “bads”, but rather might reward the positive attitude and direct it to act. Consequently, we focused on tax reliefs and designed Green Aid, that can address people’s attitude to take active participation into account by incorporating virtuous behaviours into tax relief. Green Aid Tax relief works embedded in the Green Aid Participation Scheme that bears directly on a source of environmental recovery and organizes the global call to public action in a sustained, structured, and collective participation to forestation. Green Aid bridges the action of contributing to carbon reduction with immediate, tangible, and direct benefits. It can be an alternative environmental tax, able to address and operate directly at source on emission reducers and secure effectiveness in carbon reduction and efficiency in terms of public acceptance and viability at a global level.

Under the goal of carbon peak and carbon neutrality, the carbon emission reduction of the automobile industry has attracted more and more attention in recent years. Electric vehicle has the dual attributes of power load and energy storage unit. With the increase of the number of electric vehicles, reducing carbon emissions through the collaborative interaction between electric vehicle and power network will become an important way to control carbon emissions in the automotive field. In this study, an optimization model of emission reduction benefits based on integrated development of electric vehicle and power grid is proposed, which explores the best technical way of synergy between power grid and electric vehicle, achieves the best carbon reduction effect and provides a model basis for large-scale demonstration application. Numerical simulations based on the real case in Beijing are conducted to validate the effectiveness of the proposed method.

Assuming that climate warming in the WSL will lead to a northward shift of the forest and permafrost boundaries, a “substituting space for time” approach predicts an increase in concentration of DIC and labile major and trace elements and a decrease of the transport of DOC and low soluble trace metals in the form of colloids in the main stem of the Ob River. However, an unknown factor is the change in hydrochemistry of the largest southern tributary, the Irtysh River, which is impacted by permafrost-free steppe and forest-steppe zone. Overall, seasonally-resolved transect studies of large riverine systems of western Siberia are needed to assess the hydrochemical response of this environmentally-important territory to on-going climate change.

Land degradation a serious and nationwide environmental concern in Ethiopia. The problem is its iterative relationship between land degradation, climate change, and agriculture, exacerbating one another via negative and positive feedback loops. Due to the need for an efficient response to land degradation in the country, different sustainable land management practices have been implemented since the late 1980s. The objective of this study was to analyze land degradation neutrality status using remote sensing data in the study area. We have studied the land degradation neutrality conditions of the North Wello Zone by using indicators data, namely land cover change, land productivity dynamics, and soil organic carbon stock. The result shows that the settlement areas consistently expanded at the fifth speed (2010-2018) from 1995 to 2010. Between 1995 and 2010, forestland declined by 18 percent, while an increasing trend of 26.8 percent from 2010 to 2018. The assessment results also indicate that 52.8 percent of the total area is stable and characterized by less stressed land productivity. The soil organic carbon is comparatively abundant in the high and midland vegetation areas but very thin in lowland areas. Most of the highland and midland parts of the study areas are in the conditions of stable and increasing land productivity with high biomass and soil organic content. However, most lowland areas showed a decline in land productivity conditions.

Nonwovens made of recycled carbon fibers (rCF) and thermoplastic (TP) fibers have excellent economic and ecological potential. In contrast to new fibers, recycled carbon fibers are significantly cheaper and the CO2 footprint is mostly compensated by energy savings in the first product life cycle. The next step for this promising material is its industrial serial use. Therefore the process chain from fiber to composite material is analyzed. Initially rCF length at different positions during the carding process is measured. Thereafter the influence of the TP fibers onto processing, fiber shortening and mechanical properties is evaluated. At last several nonwovens with different TP fibers and fiber volume contents between 15 vol.-% and 30 vol.-% are produced, consolidated by hot pressing and tested by 4-point bending to determine the mechanical values. The fiber length reduction ranges from 20.6 % to 28.4 %. TP fibers cushion the rCF against mechanical stress but hold rCF fragments back due to their crimp. The resulting bending strength varies from 301 MPa to 405 MPa and the stiffness from 16.3 GPa to 30.1 GPa. Design recommendations for reduced fiber shortening are derived as well as material mixtures which offer better homogeneity and higher mechanical properties.