This letter aims to show the connection between the sinc approximation for high-energy absorption cross section and the shadow radius of the spherically symmetric black hole. This connection can give a physical interpretation of the absorption cross section in the eikonal limit parameters. Moreover, the use of this alternative way, one can extract its shadow radius from the absorption cross section in high energy limits to gain more information about the black hole spacetime. Our results indicate that the increasing the value of the shadow radius of the black hole, exponentially increase the the absorption cross section of the black hole in high-energy limits which can be captured by the Event Horizon Telescope (EHT) collaboration.

Magnetic sensors are widely used in health management systems for turbomachinery, but their applications in the hot zone are limited due to the loss of magnetic properties by permanent magnets with increasing temperature. The paper presents and verifies models and design solutions aimed at improving the performance of an inductive sensor for measuring the motion of rotating objects operating at elevated temperatures (200-1000C), such as compressor and turbine blades. Physical, analog and mathematical models of the interaction of blades with the sensor were developed. A prototype of the sensor was made and its tests were carried out on the RK-4 rotor rig for the speed of 7000 rpm, in which the temperature of the sensor head was gradually increased to 1100C. The sensor signal level was compared to that of an identical sensor operating at room temperature. The heated sensor works continuously producing the output signal whose level does not change significantly. What is more, a set of six probes passed an initial engine test in an SO-3 turbojet. It was confirmed that the proposed design of the inductive sensor is suitable for blade health monitoring of the last stages of compressors, steam turbines as well as previous generation gas turbines operating below 1000C, even without a dedicated cooling system. In real-engine applications, sensor performance will depend on how the sensor is installed and the available heat dissipation capability

The use of vitamin D (VitD) supplements has become widespread in the last decade due not only to the dissociation between the blood levels recommended as "optimal" and those shown by the healthy population, but also to its presumed beneficial effects on multiple disorders. This work evaluated the levels of 25-hydroxyvitamin D [25(OH)D] in a healthy population of European origin living in a region with high solar irradiation. In serum samples from a population-based study conducted in the Canary Islands, levels of 25(OH)D were analyzed. In 876 individuals who had no history of kidney or malabsorption disorders and who had not been treated with calcium and/or VitD supplementation, the median 25(OH)D level was 26.3 (5th;95th percentile, 14.3;45.8)ng/mL. Notably, 65.4% of the population had 25(OH)D blood levels below 30ng/mL, 23.4% below 20ng/mL and 6.4% below 15ng/mL. Based on the lack of evidence supporting causality between 25(OH)D levels below what is recommended as optimal (≥20ng/mL, or even ≥30ng/mL) and major skeletal and non-skeletal diseases, and in light of the distribution of the concentration of this vitamin in healthy adults living under optimal conditions of solar irradiation, it seems reasonable to consider 25(OH)D levels below 20ng/mL and close to 15ng/mL as adequate for the general population.

In this study, we report a new epoxy acrylate based shape memory polymer(SMP) fabricated by Liquid crystal display (LCD) Stereolithographic 3D printing. The printed 3D object has a high resolution and high transparency in visible light region. The uniaxial tensile tests showed enhanced tensile toughness and tunable mechanical properties. The fix-recovery and cycle tests indicated high shape recovery properties including high shape recovery rate and excellent cycling stability. In addition, a smart electrical valve actuator was fabricated that can be used in fast heat or electricity responsive electrical circuits. LCD 3D printing provides a low-cost and high efficient way to fabricate fast responsive SMP, which can be used in wide applications in various fields on aerospace engineering, biomedical devices, soft robots and electronic devices.

The interest in high homogenization pressure technology has grown over the years. It is a green technology with low energy consumption, not generating high CO2 emissions or polluting effluents. The main food applications derive from its effect on particle size, causing a more homogeneous distribution of fluid elements (particles, globules, droplets, aggregates, etc.) and favouring the release of intracellular components; and its effect on the structure and configuration of chemical components such as polyphenols and macromolecules such as carbohydrates (fibres) and proteins (also microorganisms and enzymes). The challenges of the 21st century lead food industry processing towards obtaining food with high nutritional quality and taking advantage of waste to obtain ingredients with specific properties. For this purpose, soft and non-thermal technologies such as high pressures homogenization have a huge potential. The objective of this work is to review how the need to combine safety, functionality and sustainability in food industry has conditioned the last decade applications of high-pressure homogenization technology.

In the end of December 2019, a new strain of coronavirus was identified in the Wuhan city of Hubei province in China. Within a shorter period of time, an unprecedented outbreak of this strain was witnessed over the entire Wuhan city. This novel coronavirus strain was later officially renamed as COVID-19 (Coronavirus disease 2019) by the World Health Organization. The mode of transmission had been found to be human-to-human contact and hence resulted in a rapid surge across the globe where more than 1,100,000 people have been infected with COVID-19. In the current scenario, finding potent drug candidates for the treatment of COVID-19 has emerged as the most challenging task for clinicians and researchers worldwide. Identification of new drugs and vaccine development may take from a few months to years based on the clinical trial processes. To overcome the several limitations involved in identifying and bringing out potent drug candidates for treating COVID-19, in the present study attempts were made to screen the FDA approved drugs using High Throughput Virtual Screening (HTVS). The COVID-19 main protease (COVID-19 Mpro) was chosen as the drug target for which the FDA approved drugs were initially screened with HTVS. The drug candidates that exhibited favorable docking score, energy and emodel calculations were further taken for performing Induced Fit Docking (IFD) using Schrodinger’s GLIDE. From the flexible docking results, the following four FDA approved drugs Sincalide, Pentagastrin, Ritonavir and Phytonadione were identified. In particular, Sincalide and Pentagastrin can be considered potential key players for the treatment of COVID-19 disease.

High-Rise buildings with their particular features can affects on surrounding environment and makes new microclimates. In the windy conditions, the spaces that are between building blocks changes to passages and affects on the wind velocity, intensity and it’s other parameters.The importance of this effect is different in each level of building height. The Pedestrian-Level is the lowest and one of important areas. Markets, playgrounds and pedestrian access had located in this area and any unwanted microclimate changes like high velocity and turbulence in this level can makes discomfort and dangerous condition for residents. So this research tries to consider the pedestrian- level wind comfort in some High-Rise building complexes arrangement that had located in Tehran district 22 with Computational Fluid Dynamics (CFD) modeling and reaching to a suitable arrangement pattern. It had collected the required data through field study and librarian databases and then compared them with standard guidelines and analyzed them by comparative comparison method. As a result a linear arrangement that placed crossover to wind direction for providing wind comfort and preventing wind danger is been suggested in this region.

A new frontier in solar thermal panel technology can be a high vacuum collector, thick enough to be equipped with solar concentrators based on non-imaging optics, such as the Compound Parabolic Concentrators (CPC). The high vacuum technology guarantees higher operating temperatures thanks to the enhanced thermal insulation, which leads to pay particular attention to the absorber radiative emission. In this paper by means of numerical simulations we compare the efficiency of a flat selective solar absorber under high vacuum to the efficiency of a CPC under high-vacuum collector.

Magnetic iron oxide particles are used for in vitro diagnostics for nearly 40 years. Due to their unique physical, chemical, thermal and mechanical properties, as well as biocompatibility and low toxicity in the human body, iron oxide nanoparticles have been used in many biomedical applications, such as contrast agents for magnetic resonance imaging, carriers for controlled drug delivery and immunoassays, but also in magnetic hyperthermia. Our aim is to investigate the effect of pressure and temperature on the structural, thermal and magnetic properties of iron oxide nanomaterials prepared by hydrothermal synthesis. Iron oxide nanoparticles were synthesized at temperatures of 100-200°C and pressures of 20-1000 bar. It has been found that pressure influences the type of iron oxide crystalline phase. Thus, for lower pressure values (< 100 bar), iron oxide is predominantly formed as hematite, while at pressures > 100 bar, the major crystalline phase is goethite. The complex thermal analysis revealed the polymorphic changes of iron oxides at different temperatures. The existence of specific magnetite and hematite phases in all thermally treated samples are evidenced through the specific Verwey and Morin transitions highlighted by ZFC-FC (Zero Field Cooled-Field Cooled) measurements, whereas their relative content is precisely provided by Mössbauer spectroscopy.

By using hydrogen quench continuous annealing technology, Stelco Inc. has developed a suite of Advanced High Strength Steel (AHSS) grades with tensile strength greater than 1000MPa to meet standard automotive specifications and for unique customer requirements. These grades were optimized by correlating chemical composition and processing parameters with microstructures and mechanical properties. Dual-Phase 980 (Stelco trademarked STELMAXTM 980DP), Multi-Phase 1180 (STELMAXTM 1180MP), Martensitic Steel 1300 (STELMAXTM 1300M) and 1500 (STELMAXTM 1500M) products met strength and formability requirements with excellent flatness and surface quality. Hydrogen quench continuous annealing technology not only ensures all developed AHSS grades have consistent mechanical properties across the entire strip length (from strip head to tail) and width (from edge to edge), but also produces high product yield compared with other continuous annealing processes.

Root research on field grown crops is hindered by the difficulty of estimating root biomass in soil. Root washing, the current standard method is laborious and expensive. Biochemical methods to quantify root biomass in soil, targeting species-specific DNA, have potential as a more efficient assay. We combined an efficient DNA extraction method, designed specifically to extract DNA from soil, with well-established quantitative PCR methods to estimate the root biomass of twenty-two wheat varieties grown in field trials over two seasons. We also developed an assay for estimating root biomass for black-grass, a common weed of wheat cultivation. Two robust qPCR assays were developed to estimate the quantity of plant root DNA in soil samples, one specific to wheat and barley, and a second specific to black-grass. The DNA qPCR method was comparable, with high correlations, with the results of root washing from soil cores taken from winter wheat field trials. The DNA qPCR assay showed both variety and depth as significant factors in the distribution of root biomass in replicated field trials. The results suggest that these DNA qPCR assays are a useful, high throughput tool for investigating the genetic basis of wheat root biomass distribution in field grown crops, and the impact of black-grass root systems on crop production.

Nitride and carbide are the second phases which play an important role in the performance of bearing steel, and their precipitation behavior is complicated. In this study, TiN-MC_x precipitations in GCr15 bearing steels were obtained by non-aqueous electrolysis, and their precipitation mechanisms were studied. TiN is the effective heterogeneous nucleation site for Fe₇C₃ and Fe₃C, therefore, MC_x can precipitate on the surface of TiN easily, its chemistry component consists of M₃C and M₇C₃ (M = Fe, Cr, Mn) and Cr₃C₂. TiN-MC_x with high TiN volume fraction, TiN forms in early stage of solidification, and MC_x precipitates on TiN surface after TiN engulfed by the solidification advancing front. TiN-MC_x with low TiN volume fraction, TiN and MC_x form in late stage of solidification, TiN can not grow sufficiently and is covered by a large number of precipitated MC_x particles.

The detection of temporary color steel buildings and the analysis of their spatiotemporal patterns and characteristics are of great importance in many developing cities, because areas densely distributed with color steel buildings are usually problematic regions with high population density, sustainable development and risk level, which are challenging for local governments. Using the high-resolution satellite images of the Anning District, Lanzhou City, China as the case study, this paper first extracts the information of the color steel buildings for two different periods. Then the spatiotemporal distributional characteristics of the color steel buildings are analyzed, both at small scale (temporary buildings) and large scale (planthouses, warehouses, etc.). Finally, this paper utilizes kernel density estimation, Delaunay triangulation and Voronoi diagrams to examine the spatial distribution, aggregation and proximity characteristics of the color steel buildings. Our experiments show that the temporal and spatial differences of urban development, the phased characteristics and urban space are represented by various types of color steel buildings. Thus, there are some robust coupling relationship between color steel buildings, urban spatial form and urban development.

By combing continuum topology optimization (TO) method and lattice structure technique, a sandwich aircraft spoiler with a high stiffness-to-weight is designed. TO method is served to produce the shell of the aircraft spoiler and the lattice structure, used as cores, is employed to support the shell. TO problem is established as maximizing the stiffness of the structure with limited material volume. Density-based method is utilized to achieve a 0/1 solution. We then empirically replace the core of the aircraft spoiler by using 3D kagome lattice structure. Two different materials, i.e., aluminum alloy and titanium alloy, are synthetically applied to further reduce the weight and simultaneously improve the strength of the aircraft spoiler. Numerical simulations are conducted to show that the designed aircraft spoiler can meet the service environment with a reduction of its weight by approximately 80% when compared with that of the initial design model. Finally, we have fabricated the designed model with photosensitive resin by using 3D printing technique.

The Pierre Auger Observatory is the world's largest operating detection system for the observation of ultra high energy cosmic rays (UHECRs). The detector allows detailed measurements of their energy spectrum, mass composition and arrival directions of primary cosmic rays in the energy range above $10^{17}$ eV. The data collected at the Observatory over the last decade show the suppression of the cosmic ray flux at energies above $4\times10^{19}$ eV. However, it is still unclear if this suppression is caused by the propagation of cosmic rays or rather by energy limitation of their sources. The other puzzle is the origin of UHECRs. Some clues can be drawn from studying the distribution of their arrival directions. The recently observed dipole anisotropy has an orientation which indicates an extragalactic origin of UHECRs. The Auger surface detector array is also sensitive to showers due to ultra high energy neutrinos of all flavours and photons, and recent neutrino and photon limits provided by the Observatory can constrain models of the cosmogenic neutrino production and exotic scenarios of the UHECRs origin, such as the decays of super heavy particles. In this paper the recent results on measurements of the energy spectrum, mass composition and arrival directions of cosmic rays, and future prospects are presented.

Factors affecting the host-virus interaction must be understood for the effective application of bacteriophages to combat bacterial pathogens. Two novel E. coli phages, the T1-like siphophage LL5 and the rV5-like myophage LL12, were subjected to forward genetic screens against the Keio collection, a library of single non-essential gene deletions in E.coli str. BW25113. These genome-wide screens and subsequent experiments identified eight genes required for efficient propagation of phage LL5 and six genes required for propagation of LL12. The majority of the genes identified were involved in production of the phage receptors. E. coli mutants deficient in heptose II and the phosphoryl substituent of heptose I of the inner core lipopolysaccharide (LPS) were unable to propagate phage LL5, as were mutants deficient in the outer membrane protein TolC. Mutants lacking glucose I of the LPS outer core failed to propagate LL12. Two cytoplasmic chaperones, PpiB and SecB, were found to be required for efficient propagation of phage LL5 but not LL12. This approach may be useful for identifying phage receptors and required host factors in other phages, which would provide valuable information for their potential use as therapeutics and for phage engineering.

The present study examined and compared the effects of high- and low-molecular weight (MW) chitosan, a nutraceutical, on intestinal and liver lipid metabolism in rats fed with high-fat diet. Both high- and low-MW chitosan decreased liver weight, elongated small intestine, improved the dysregulation of blood lipids and liver fat accumulation, and increased fecal lipid excretion in high-fat diet-fed rats. Supplementation of both high- and low-MW chitosan significantly inhibited the decreased phosphorylated AMP-activated protein kinase (AMPK)α and peroxisome proliferator-activated receptor (PPAR)α protein expressions and the increased lipogenesis/cholesterogenesis-associated protein expressions (sterol regulatory element binding protein (SREBP)1c, SREBP2, and PPARγ) and the decreased apolipoprotein (Apo)E and microsomal triglyceride transfer protein (MTTP) protein expressions in the livers of high-fat diet-fed rats. Both high and low-MW chitosan supplementation could also suppress the increased MTTP protein expression and the decreased angiopoietin-like protein (Angptl)4 protein expression in the intestines of high-fat diet-fed rats. Comparison between high and low-MW chitosan, high-MW chitosan has a higher efficiency than low-MW chitosan on the inhibition of intestinal lipid absorption and the increase of hepatic fatty acid oxidation, which can improve liver lipid biosynthesis and accumulation.

This review discusses a broad range of recent advances (2013-2017) of chemical imaging using electrochemical methods, with a particular focus on techniques that have been applied to study cellular processes, or techniques that show promise for use in this field in the future. Non-scanning techniques such as microelectrode arrays (MEAs) offer high time-resolution (< 10 ms) imaging, however at reduced spatial resolution. In contrast, scanning electrochemical probe microscopies (SEPMs) offer higher spatial resolution (as low as a few nm per pixel) imaging, with images collected typically over many minutes. Recent significant research efforts to improve the spatial resolution of SEPMs using nanoscale probes, and to improve the temporal resolution using fast scanning have resulted in movie (multiple frame) imaging with frame rates as low as a few seconds per image. Many SEPM techniques lack chemical specificity or have poor selectivity (defined by the choice of applied potential for redox-active species). This can be improved using multifunctional probes, ion-selective electrodes and tip-integrated biosensors, although additional effort may be required to preserve sensor performance after miniaturization of these probes. We discuss advances to the field of electrochemical imaging, and technological developments which are anticipated to extend the range of processes that can be studied. This includes imaging cellular processes with increased sensor selectivity and at much improved spatiotemporal resolution than has been previously customary.

Face routing has been adopted in wireless sensor networks (WSNs) where topological changes occur frequently or maintaining full network information is difficult. For message forwarding in networks, a planar graph is used to prevent looping, and because long edges are removed by planarization and the resulting planar graph is composed of short edges, messages are forwarded along multiple nodes connected by them even though they can be forwarded directly. To solve this, face routing using information on all nodes within 2-hop range was adopted to forward messages directly to the farthest node within radio range. However, as the density of the nodes increases, network performance plunges because message transfer nodes receive and process increased node information. To deal with this problem, we propose a new face routing using the planar graphs of neighboring nodes to improve transfer efficiency. It forwards a message directly to the farthest neighbor and reduces loads and processing time by distributing network graph construction and planarization to the neighbors. It also decreases the amount of location information to be transmitted by sending information on the planar graph nodes rather than on all neighboring nodes. Simulation results show that it significantly improves transfer efficiency.

The objective of this study is to evaluate the effect of constitutive equations on the prediction accuracy for springback in cold stamping with various deformation modes. In this study, two types of yield functions—Hill’48 and Yld2000-2d—were considered to describe yield behavior. Isotropic and kinematic hardening models based on the Yoshida–Uemori model were also adopted to describe hardening behavior. Various material tests (such as uniaxial tension, tension- compression, loading-unloading, and hydraulic bulging tests) were carried out to determine the material parameters of the models. The obtained parameters were implemented in the finite element (FE) simulation to predict springback, and the results were compared with experimental data. U-bending and T-shape drawing were employed to evaluate the springback prediction accuracy. Obviously, the springback prediction accuracy was greatly influenced by constitutive equations. Therefore, it is important to choose appropriate constitutive equations for accurate description of material behaviors in FE simulation.

A high step-up DC-to-DC converter that integrates an isolated transformer and a switched-clamp capacitor is presented in this study. The voltage stress of the main power switch should be clamped to 1/4 V by using the turn ratio and switched-clamp capacitor of an isolated transformer to achieve a high voltage gain. In addition, a passive clamp circuit is employed reduce voltage stress on the main power switch. The energy of the leakage inductor can be recycled by the clamp capacitor because of the passive clamp circuit, thereby improving the power converter efficiency. The converter consists of one isolated transformer, one main switch, three capacitors, and four diodes. Operating principle and steady-state analyses are also discussed. Finally, a 24-V-input voltage to 200-V-output voltage and a 150 W output power prototype converter are fabricated in the laboratory. The maximum efficiency of the converter is 95.1 at 60 W.

This contribution is an attempt to reconstruct the favorable atmosphere that prevailed in Lau-sanne in 1986-87 and provided the backdrop of our invention of two-dimensional ion cyclotron resonance mass spectroscopy (2D ICR-MS). To avoid a self-centered histoire d’ancien combattant, we shall try to emphasize the context, the contributions of key players within our nascent research group at UNIL and the established group of Tino Gäumann at EPFL, the role of external speakers, and the open atmosphere that was not yet polluted by bibliometrics, obsessive concern with im-pact factors, and top-down management of research. We shall also explain why the idea of 2D ICR-MS has been ignored for many years and still has a limited impact: different scientific cul-tures in the ICR and NMR communities, different concerns with fundamental vs. applied research, different status of theory and numerical simulations, different levels of commitment of instrument manufacturers, not to mention many theoretical problems that appear to be at least as challenging in ICR as in NMR.

This article deals with the conformable double Laplace transforms and their some properties with examples and also the existence Condition for the conformable double Laplace transform is studied. Finally, in order to obtain the solution of nonlinear fractional problems, we present a modified conformable double Laplace that we call conformable double Laplace decomposition methods (CDLDM). Then, we apply it to solve, Regular and singular conformable fractional coupled burgers equation illustrate the effectiveness of our method some examples are given.

Exact solutions to conformable time fractional (3+1)- dimensional equations are derived by using the modified form of the Kudryashov method. The compatible wave transformation reduces the equations to an ODE with integer orders. The predicted solution of the finite series of a rational exponential function is substituted into this ODE. The resultant polynomial equation is solved by using algebraic operations. The method works for the Jimbo-Miwa, the Zakharov-Kuznetsov and the modified Zakharov-Kuznetsov equations in conformable time fractional forms. All the solutions are expressed in explicit forms.

The durability of bridge decks is a critical factor in ensuring the safety and longevity of transportation infrastructure. This article explores advanced materials and innovative techniques designed to mitigate cracking in bridge decks, a common issue that can compromise structural integrity and increase maintenance costs. It provides a comprehensive review of cutting-edge solutions such as Fiber-Reinforced Polymers (FRP), High-Performance Concrete (HPC), Ultra-High Performance Concrete (UHPC), and self-healing concrete technologies. Each material is analyzed for its ability to enhance strength, reduce permeability, and improve resistance to environmental stressors. Additionally, the article examines the role of surface treatments, sealants, and routine maintenance practices in prolonging the life of bridge decks. By synthesizing current research and practical applications, this article offers valuable insights and recommendations for engineers, contractors, and policymakers seeking to advance bridge deck durability through innovative materials and methodologies.

Cutaneous metastatic melanoma (CMM) is the most aggressive form of skin cancer with a poor prognosis. Drugs-induced secondary tumorigenesis and the emergency of drug resistance worsen the already worrying scenario, thus rendering urgent the development of new treatments, not dealing with mutable cellular processes. Triphenyl phosphonium salts (TPPSs), in addiction to act as cytoplasmic membrane disruptors, are reported to be mitochondria-targeting compounds, exerting anticancer effects mainly by damaging their membranes and causing depolarization, impairing mitochondria functions and their DNA, triggering oxidative stress (OS), and priming primarily apoptotic cell death. TPP-based bola-amphiphiles are capable to self-form nanoparticles (NPs) with enhanced biological properties, as commonly observed for nanomaterials. Already employed in several other biomedical applications, only recently the per se selective potent antibacterial effects of a TPP bola-amphiphile has been demonstrated on 50 multidrug resistant (MDR) clinical superbugs, as well as its exceptional and selective anticancer properties, on sensitive and MDR neuroblastoma cells. Here, aiming at finding new molecules possibly developable as new treatments for counteracting CMM, the effects of this TPP-based bola-amphiphile (BPPB) have been investigated against two BRAF mutants CMM cell lines (MeOV and MeTRAV) with excellent results (even IC50 = 49 nM on MeOV after 72 h treatment). Upon these findings and considered the low cytotoxicity of BPPB against different mammalian not tumoral cell lines and red blood cells (RBCs, selectivity indexes up to 299 on MeOV after 72 h treatment), the possible future development of BPPB as topical treatment for CMM lesions was presumed. In this sight, a biodegradable hyaluronic acid (HA)-based hydrogel formulation (HA-BPPB-HG) was prepared without using any potentially toxic crosslinking agents, but simply dispersing suitable amounts of the two ingredients in water and sonicating under gentle heating. HA-BPPB-HA was completely characterized with promising outcomes, such as high swelling capability, high porosity and viscous elastic rheological behavior.

The compound, C27H23N3 (1), crystallizes in the triclinic system of the P-1 space group. The unit cell comprises a dimer of 1, in which the monomers are linked by two complementary hydrogen bonds between N1 and H1-C1 of another molecule. The dimers form chains along the a-axis through intermolecular interactions between the N2 acceptor atoms and C17 donors from molecules in the nearest neighbouring dimer. These interactions form extended sheets of the dimers of 1, along the ab plane. The quinolinylmeth-2-yl groups of 1 lie in almost orthogonal planes and their N1/2(q) donor atoms being away from the apical amino N3 atom.

In this paper, some new properties of the fundamental solution to the multi-dimensional space- and time-fractional diffusion-wave equation are deduced. We start with the Mellin-Barnes representation of the fundamental solution that was derived in the previous publications of the author. The Mellin-Barnes integral is used to get two new representations of the fundamental solution in form of the Mellin convolution of the special functions of the Wright type. Moreover, some new closed form formulas for particular cases of the fundamental solution are derived. In particular, we solve an open problem of representation of the fundamental solution to the two-dimensional neutral-fractional diffusion-wave equation in terms of the known special functions.

Satellite-derived high-resolution soil moisture and precipitation data have become widely adopted in natural hazard and climate change research. Landslide susceptibility mapping, which often relies on static predisposing factors, faces challenges in accounting for temporal changes, limiting its efficacy in accurately identifying potential locations for landslide occurrences. A key challenge is the lack of sufficient ground-based monitoring networks for soil moisture and precipitation, especially in remote areas with limited access to rain gauge data. This study addresses these limitations by integrating static landslide conditioning factors—such as topography, geology, and landscape features—with high-resolution dynamic satellite data, including soil moisture and precipitation. Using machine learning techniques, particularly the Random Forest (RF) algorithm, the approach enables the generation of dynamic landslide susceptibility maps that incorporate both spatial and temporal variations. The work validates the method by analyzing two major landslide events and their relationship to hydrological factors, occurred during two rainfall events in 2019 in Italy. The results successfully identified high-probability landslide areas by accounting for multiple hydrogeological factors and capturing the unique patterns of rainfall and soil moisture distribution and intensity. The findings emphasize the need for further research to refine the use of high-resolution satellite precipitation and soil moisture data, particularly in identifying the optimal temporal and spatial resolutions for landslide susceptibility mapping.

This paper investigates the flexural behavior of unfired and fired one-way slabs constructed from reinforced ferronickel slag-based alkali-activated concrete. The study aims to expand the limited knowledge of large-scale testing of alkali-activated concrete structural elements, with a particular emphasis on their post-fire performance. Four slabs, each measuring 2.1 × 0.9 × 0.18 m³, were produced—two made of alkali-activated concrete and two of conventional concrete incorporating ordinary Portland cement. Both types of concrete exhibited similar compressive strengths. In each group, one slab served as a reference (control specimen—tested under monotonic four-point bending in its original state), while the other was subjected to a standard fire curve on the tensioned side before mechanical testing. The fired slabs were then tested in a cooled condition under ambient conditions. The effect of fire on the alkali-activated concrete was further examined using mercury intrusion porosity and scanning electron microscopy. The results reveal that the load capacity of structural members cast with alkali-activated concrete is only slightly lower than that of their conventional concrete counterparts (6% lower). However, the alkaliactivated slabs retain more of their stiffness and ductility after fire exposure.

Bandsaw blades are typical band-shaped cutting tools characterized by low stiffness and micro-level cutting depth, resulting in distinct wear mechanisms compared to rigid cutting tools. In this study, the wear curve and wear mechanisms of bandsaw tooth during the bandsawing of Cr12MoV cold-working steel was investigated. The tool life was divided into two stages: a rapid wear stage (Stage I) and a homogeneous wear stage (Stage II). In Stage I, the wear was dominated by chipping although multiple wear mechanisms were found due to the relatively poor manufacturing accuracy compared to rigid cutting tools, which results in remarkable differences among the cutting depths of individual teeth. In Stage II, abrasive and adhesive wear were the primary wear mechanisms instead of chipping, which was related to the microstructure of Cr12MoV. Furthermore, methods for increasing the bandsaw performance were proposed based on the tooth wear mechanisms.

In this paper, we demonstrate a method of measuring the flexural elastic modulus of ceramics at an intermediate (~millimeter) scale, at high temperatures. We used a picosecond laser to precisely cut micro-beams from the location of interest in a bulk ceramic. They had a cross-section of approximately 100 μm × 300 μm, and a length of ~1 cm. They were then tested in a thermal-mechanical analyzer at room temperature, 500°C, 800°C, and 1100°C using the four-point flexural testing method. We compared the elastic moduli of high-purity Al2O3 and AlN measured by our method with the reported values in the literature and found that the difference was less than 5% for both materials. This paper provides a new and accurate method of characterizing the high-temperature elastic modulus of miniature samples extracted from representative/selected areas of bulk materials.

Land subsidence is an environmental hazard occurring gradually over time, potentially posing significant threats to the structural stability of civilian buildings and essential infrastructures. This study presented a workflow using the SBAS-PSInSAR approach to analyze surface deformation in the Choushui River fluvial plain (CRFP) based on Sentinel-1 SAR images and validated against precise leveling. Integrating InSAR results with hydrogeological data, such as groundwater levels, multilayer compactions, and borehole loggings, a straightforward model was proposed to estimate appropriate groundwater level drops to minimize further subsidence. The results showed a huge subsidence bowl centered in Yunlin, with maximal sinking at an average 60 mm/year rate. High-resolution subsidence maps enable the quantitative analyses of the safety issues for Taiwan High Speed Rail (THSR) across the considerable subsidence areas. In addition, the analysis of hydrogeological data revealed that half of the major compaction in the study area occurred at shallow depths. Based on a maximal subsidence control rate of 40 mm/year specified in the CRFP, the model results indicated that the groundwater level drops from wet to dry seasons needed to be maintained from 3-5 m for the shallowest aquifer and 4 – 6 m for aquifers 3 and 4. The workflow demonstrated the compatibility of InSAR with traditional geodetic methods and the effectiveness of integrating multiple data sources to assess the complex nature of land subsidence in the CRFP.

In recent years, the High Dynamic Range (HDR) image has gained widespread popularity 1 across various domains such as security, multimedia, and biomedical fields, owing to its ability 2 to deliver an authentic visual experience. However, the extensive dynamic range and rich detail 3 in HDR images present challenges in assessing their quality. Therefore, current efforts involve 4 constructing subjective databases and proposing objective quality assessment metrics to achieve 5 efficient HDR Image Quality Assessment (IQA). Recognizing the absence of a systematic overview 6 of these approaches, this paper provides a comprehensive survey of existing HDR IQA methods. 7 Furthermore, this paper aims to serve as a valuable resource for researchers by discussing the 8 limitations of current methodologies and potential research directions in the future.

The purpose of this study was to establish the association between total and segmental body composition (BC) variables and anaerobic performance and to create optimal models that best predict such performance in CrossFit® (CF) athletes. Fifty athletes, 25 males and 25 females (age: 33.26 ± 6.81 years; body mass: 72.57 ± 12.17 kg; height: 169.55 ± 8.71 cm; BMI: 25.06 ± 2.31 kg·m−2) were recruited to participate and underwent BC analysis using dual-energy X-ray absorptiometry (DXA) and an all-out laboratory test on a cycle ergometer (Wingate) to determine their anaerobic performance. The results show a significant correlation between BC values and performance, ranging from moderate (r = -0.34, p = 0.015) to near-perfect (r = 0.96, p &lt; 0.01). Furthermore, the created performance prediction models exhibited predictive capacities ranging from 19% (p = 0.017) to 93% (p &lt; 0.001). All prediction models were created using total or segmental lean mass variables, excluding others. BC and performance variables found significant differences between males and females. The findings demonstrate that BC variables are crucial indicators of anaerobic performance in CF athletes. Professionals responsible for athlete performance should use this information to monitor athletes and design training programs.

Diffusion magnetic resonance imaging (dMRI) is an imaging technique that provides information on the microstructural organization of biological tissue. dMRI allows for non-invasive visualization and quantitative assessment of white matter architecture in the brain by characterizing restrictions on the random motion of water molecules. Ultra-high field MRI scanners, such as those operating at 7 Tesla (7T) or higher, can boost signal-to-noise ratio (SNR) to improve dMRI compared with what is attainable at conventional field strengths such as 3T or 1.5T. However, at 7T wavelength effects cause lower transmit magnetic field efficiency in the human brain, mainly in the posterior fossa region, manifesting as signal dropouts in this region. Recently, we reported a simple approach of using a wireless radiofrequency (RF) surface array to improve transmit efficiency and signal sensitivity at 7T. Here we demonstrate the feasibility and effectiveness of using this RF enhancer for in-vivo dMRI at 7T. The use of the RF enhancer can effectively recover signal dropouts in the regions with intrinsically lower SNR such as cerebellum, leading to a better depiction of principal fiber orientations and enhanced visualization of extended tracts to the brainstem and pons enabling more comprehensive delineation of the full white matter architecture.

In the realm of high-pressure vessel simulation, conventional finite element method (FEM) approaches, as per ASME standards, may inadequately predict the behavior of flat surfaces under elevated temperatures. This study challenges the efficacy of shell-type mesh modeling for high-temperature flat plates, demonstrating that the thermal conditions within such high-pressure vessels can induce thermal instability and buckling, not accounted for by traditional FEM methods recommended by ASME. Through comprehensive analytical investigations, we reveal that traditional shell-type meshing techniques, while suitable for certain applications, fail to capture the intricate thermal stresses and deformation patterns inherent in high-temperature flat plate configurations. Our analysis delineates distinct stability regimes governed by key design parameters—including plate thickness, operating temperature, and geometric dimensions—profoundly impacting the structural integrity of heating plates under thermal loading. By elucidating these stability boundaries, this research provides engineers with critical insights necessary for optimizing the design and performance of high-temperature equipment. This includes the design of high-pressure vessels with flat surfaces for heating materials, flanges in high-temperature environments, and fins in heat exchangers across various industries such as oil and gas, pyrolysis, and power plants. The findings presented herein serve as a valuable reference for engineers seeking to comprehend and mitigate instability phenomena in solid mechanics, offering practical guidance for developing robust and reliable high-temperature structures in demanding industrial environments.

Overconsumption of an unbalanced diet and overweight, leading to insulin resistance, dyslipidemia, hepatic steatosis, cardiovascular diseases and obesity, is nowadays a worldwide health issue, with different patterns of metabolic disturbances in the young and adult popula-tions, in both gender. Preclinical models that closely mimic the gradual weight gain that occurs in humans upon consumption of a “western-type” diet (WD) are of great interest. In particular, the diet-induced obesity (DIO) model in the C57BL/6J mouse sub-strain is often used in biomed-ical research, considering that it is prone to metabolic disorders and obesity, and is widely used to generate genetically modified mice. This study aimed to phenotypically characterize the C57BL/6J mouse strain fed a WD-like diet, using high-frequency ultrasound imaging (HFUS) as a complementary tool to longitudinally monitor morphofunctional changes in the liver, heart and kidney associated with DIO. Long term WD feeding increased mice body weight (BW), liver/BW ratio and body condition score (BCS), serum transaminases, glucose and insulin, as well as Homeostasis model assessment (HOMA) indexes, and caused dyslipidemia and insulin resistance. According to the 3Rs, ultrasound imaging has enabled a comprehensive study of metabolic syndrome in mice, in vivo and non-invasive, improving the identification of early stages of diseases.

There are few results about the internal damping ratio of normal and high strength concretes. Hence, this paper presents the expansion of the investigation about internal damping ratio under undamaged and damaged conditions, for usual concretes (NSC) and high strength concretes (HSC). In this way, the study cover a strength range of 42 to 83 MPa. Cyclic load was employed by a servo-controlled hydraulic testing machine and for each cyclic step the dynamic elastic modulus (Ed) and internal damping ratio (ξ) were determinate by acoustic tests. Normal strength concretes (fc = 42MPa) presented undamaged internal damping ratio ξ = 0.5% and achieved the maximum value of ξ = 2.5 for a damage index equal to 0.8. High strength concretes mixtures (fc = 83MPa) presented an undamaged internal damping of ξ=0.29% and maximum internal damping equal to ξ=0.93% (under damage index of 0.32). Porosity and the transition zones were the responsible to the initial internal damping values and how the material behavior under each cyclic load. The progressive damage generates the increase of coulomb damping. There are few studies allowing the quantification and comprehension of internal damping ratio under damage cyclic loading and this approach will lead to improve the understanding of NSC and HSC under dynamical excitation subject to damage evolution, mainly in impact situations.

The major challenge in the current context of a rising world’s energy demand is to limit the global temperature increase for mitigating climate change. This goal requires a large reduction of CO2 emissions, mainly produced by power generation and industrial processes using fossil fuels. In this study, a novel methodology for K2CO3-doped Li4SiO4 sorbents production for CO2 capture at high temperature was adopted based on the Design of Experiments (DoE). Different synthesis (temperature and K2CO3 content) and adsorption conditions (sorption temperature and CO2 concentration) were systematically tested by Response Surface Methodology (RSM) to obtain predictive models of CO2 uptake and Li4SiO4 conversion. The results of RSM analysis evidenced a maximum adsorption capacity of 196.4 mg/g for a sorbent produced at 600 °C and with 36.9 wt% of K2CO3, tested at 500 °C and 4 vol% of CO2. Whereas at 50 vol% of CO2, the best uptake of 295.6 mg/g was obtained with a sorbent synthesized at 600 °C, containing less K2CO3 (17.1 wt%) and tested at higher temperature (662 °C). The obtained results highlight that K2CO3-doped Li4SiO4 sorbents can be tailored for maximizing CO2 capture at different operating conditions, making them suitable for use in industrial processes.

Increased activity of transforming growth factor-beta (TGF-β) is a key factor mediating kidney impairment in diabetes. Glomerular podocytes, the crucial component of the renal filter, are a direct target of TGF-β action, resulting in irreversible cell loss and progression of chronic kidney disease (CKD). Urolithin A (UA) is a member of the family of polyphenol metabolites produced by gut microbiota from ellagitannins and ellagic acid-rich foods. The broad spectrum of biological ac-tivities of UA makes it a promising candidate for the treatment of podocyte disorders. In this in vitro study, we investigated whether UA influences the changes exerted in podocytes by TGF-β and high glucose. Following a 7-day incubation in normal (NG, 5.5 mM) or high (HG, 25 mM) glucose the cells were treated with UA and/or TGF-β1 for 24 hours. HG and TGF-β1, each independent and in concert reduced expression of nephrin, increased podocyte motility and up-regulated expression of b3 integrin and fibronectin. These typical for epithelial-to-mesenchymal transition (EMT) effects were inhibited by UA in both HG and NG conditions. UA also reduced the typically elevated in HG expression of TGF-β receptors and activation of TGF-β signal transducer Smad2. Our results indicate that in podocytes cultured in conditions mimicking diabetic milieu, UA inhibits and reverses changes underlying podocytopenia in diabetic kidneys. Hence, UA should be considered as a po-tential therapeutic agent in podocytopathies.

The higher education sector in Africa has experienced remarkable growth over the past decades, enrolling and graduating millions of students annually. Despite this progress, high unemployment rates among graduates and pervasive underdevelopment have raised questions about the relevance of higher education in Africa. Critics have intensely scrutinized the quality of curricula, highlighting a significant mismatch between the skills offered and the demands of the job market. This disconnect is often due to curricula that are unresponsive to both job requirements and students' needs. Enhanced pedagogical approaches are essential to address this issue. Community engagement and service learning (CE&SL) offer promising solutions by bridging the gap between theoretical knowledge and practical application. Recognizing the potential benefits, higher education institutions across the continent are gradually integrating CE and SL into their teaching and research frameworks. However, the adoption of these approaches has been slow. This paper explores the opportunities and challenges hindering the effective and widespread implementation of CE and SL in African higher education institutions and proposes practical strategies to overcome these obstacles. By embracing these innovative approaches, African universities can better prepare graduates for the dynamic job market and contribute more effectively to the continent's development.

Coastal environments are complex systems that are influenced by a combination of natural processes and human activities. Scientific interest in the effects of coastal erosion/accretion and climatic change-related processes greatly increased in recent decades due to the growing human development along coastal areas. This paper investigates the state and evolution of beach-dune systems for the 1977-2001 and 2001-2019 periods of the Mediterranean coast of Andalusia (Spain) using two different proxies: the dune toe line, which was used to track foredunes evolution, and the high-water line, which was used to assess shoreline evolution. Results showed a general erosional behavior of the studied beach-dune systems and identified cases where the main trend was altered through human interventions. In the 1977-2001 period, 54% of foredunes showed erosion, 24% accretion and 22% stability while and 34% of shorelines showed erosion, 40% accretion and 34% stability. In the 2001-2019 period, 42% of foredunes showed erosion, 28% accretion and 30% stability, and 40% of shorelines showed erosion, 34% accretion and 26% stability. Combining the evolution classes of each proxy (dune toe/shoreline) allows the behavior of both shoreline proxies to be assed together and provides insights additional to those derive from the use of a single proxy. In this regard, Erosion/Erosion (EE) was the most frequent behavior, with 25% and 27% in the first and second periods respectively, and Accretion/Accretion (AA), with 17% in both periods. Erosion of foredunes combined with stability or accretion of the shoreline (ES and EA) were the most common pairings in the first period, while stability of dunes combined with accretion of the shoreline (SA) and Stability/Stability (SS) dominated in the second period. The results obtained provide additional insights on the nature and drivers of coastal change that aid local coastal managers and administrations in understanding erosion processes. The method can be applied at other areas around the world where a similar data base is available.

Abstract Purpose: This study aims to evaluate the potential of multimodal ultrasound techniques in improving the visibility of liver lesions that are indistinct under conventional ultrasound. Specifically, we will explore the application of fusion imaging, contrast-enhanced ultrasound (CEUS), and high-frequency ultrasound in enhancing the visibility of liver masses. These techniques will be utilized to assist in visualizing liver lesions and to accurately localize them for the purpose of performing percutaneous tissue biopsy. Lastly, we will compare the biopsy results with the final diagnosis to assess whether multimodal techniques can enhance the success rate of percutaneous biopsy for liver masses that are not clearly visible under conventional ultrasound. Furthermore, the potential impact of these techniques on the development of personalized treatment strategies for patients was also discussed. Materials and Results: A retrospective analysis was conducted on 144 patients with liver masses who underwent conventional ultrasound examinations at our hospital from October 2018 to January 2024. These patients had poor visibility on conventional ultrasound, but the tumor location was visible on abdominal computerized tomography (CT) or magnetic resonance imaging (MRI) scans. We excluded 71 patients who did not undergo percutaneous liver tumor biopsy and 8 patients who remained non-visualized under multimodal ultrasound. Finally, 95 patients met the inclusion criteria and their clinical and radiological data were selected for analysis. Computerized tomography or magnetic resonance imaging-ultrasound (CT/MR-US) fusion imaging was performed in 55 patients, CEUS was conducted in 95 patients, and high-frequency ultrasound examination was performed in 21 patients. The visibility of the lesions using these three techniques was evaluated, and the consistency between the biopsy pathology and the final diagnosis was analyzed. Results: In the study, a total of 39 cases were identified as solitary liver lesions, 34 cases as multiple lesions, and an additional 23 cases as diffuse hepatocellular carcinoma. Among them, there were 13 cases (13.7%) of lesions located in the left lobe, 73 cases (76.8%) in the right lobe, and 9 cases (9.4%) at the junction of the left and right lobes. The average maximum diameter of the lesions was 2.7 cm (ranging from 0.7 cm to 10.0 cm). The detection rates of lesions using CT/MR-US fusion imaging, contrast-enhanced ultrasound (CEUS), and high-frequency ultrasound examination were 49.1%, 96.8%, and 76.2%, respectively. All patients in the entire cohort underwent percutaneous ultrasound-guided biopsy after confirming the target location of the lesions, including 9 patients underwent percutaneous microwave ablation. No severe complications were observed. The accuracy rate of the biopsies was 91.6%, and the positive concordance rate was 91.1%. The biopsy pathology included 39 cases of hepatocellular carcinoma (HCC), 16 cases of intrahepatic cholangiocarcinoma (ICC), 22 cases of metastatic adenocarcinoma, 3 cases of hepatic adenoma (HA), 1 case of vascular sarcoma, and 1 case of mixed HCC-ICC. Among the 13 patients with negative pathology findings after biopsy, 8 cases were considered false negatives (based on follow-up laboratory tests and imaging results consistent with malignant tumor characteristics), resulting in a false negative rate of 8.9%. Conclusions: The application of multimodal ultrasound technology can significantly improve the success rate of liver lesion biopsies that are difficult to visualize using conventional ultrasound. Furthermore, it will facilitate the guidance of microwave ablation therapy for lesions using multimodal ultrasound imaging, enabling collaborative precision treatment planning for patients with clinical physicians.

An analysis of the processes of plastic deformation and acoustic relaxation in a high-entropy alloy Al0.5CoCrCuFeNi was carried out. The following have been established: dominant dislocation defects; types of barriers that prevent the movement of dislocations; mechanisms of thermally activated movement of various elements of dislocation lines through barriers at room and low temperatures. Based on modern dislocation theory, quantitative estimates have been obtained for the most important characteristics of dislocations and their interaction with barriers.

CO2 geological sequestration in coal seams can achieve the dual objectives of CO2 emission reduction and enhanced coalbed methane production, making it a highly promising carbon capture and storage technology. However, the injection of CO2 into coal reservoirs in the form of supercritical fluid (ScCO2) leads to complex physicochemical reactions with the coal seam, altering the properties of the coal reservoir and impacting the effectiveness of CO2 sequestration and methane production enhancement.In this paper, theoretical calculations based on ReaxFF-MD were conducted to study the interaction mechanism between ScCO2 and the macromolecular structure of both low-rank and high-rank coal, to address the limitations of experimental methods. The reaction of ScCO2 with low-rank coal and high-rank coal exhibits significant differences. At swelling stage, the low-rank coal experiences a decrease in aromatic structure and aliphatic structure, high-rank coal shows an increase in aromatic structure and a decrease in aliphatic structure, while swelling phenomenon is more pronounced in high-rank coal. At dissolution stage, low-rank coal is initially decomposed into two secondary molecular fragments, and then recombine to form new molecular structure, the aromatic structure increased and the aliphatic structure decreased. In contrast, high-rank coal occurs stretches-breakage-movement-reconnection, a reduction in aromatic structure and an increase in aliphatic structure.The primary reasons for these variations lie in distinct molecular structure compositions and the properties of ScCO2, leading to different reaction pathways of functional group and aromatic structure. The reaction pathways of functional groups and aromatic structures in coal can be summarized as follows: the breakage of the O-H bond in hydroxyl groups, the breakage of the C-OH bond in carboxyl groups, transformation of aliphatic structures into smaller hydrocarbon compounds or formation of long-chain alkenes, and various pathways involving broken, rearrangement, recombination of aromatic structures. In low-rank coal, there is a higher abundance of oxygen-containing functional groups and aliphatic structures. The breakage of O-H and C-OH chemical bonds results in the formation of free radical ions, while some aliphatic structures detach to produce hydrocarbons. Additionally, some of these aliphatic structures combine with carbonyl groups and free radical ions to generate new aromatic structures. Conversely, in high-rank coal, the lower content of oxygen-containing functional groups and aliphatic structures, along with stronger intramolecular forces, results in fewer chemical bond breakages and makes it less conducive to the formation of new aromatic structures.These results elucidate the specific deformations of different chemical groups, offering a molecular-level understanding of the interaction between CO2 and coal.

The objective of this study was to investigate the relationship between high-performance work systems and a company’s social performance, taking into account the organizational climate as a situational variable. Specifically, this study aimed to analyze the impact of perceptions of a high-performance work system on the perception of a company’s social responsibility (CSR) among employees of Jordanian companies with an organizational size of 300 or more. This study used 175 valid questionnaires, and SPSS and AMOS 24 were used to test the hypotheses. The results showed that there was a positive relationship between the perception of a high-performance work system and the perception of a company’s CSR. Furthermore, this study found that a positive diversity climate could enhance the positive relationship between the two. These findings suggest that high-performance work systems can contribute to the development of sustainable human resource management systems and that a positive diversity climate is essential in shaping these systems. Based on these results, it is recommended that companies implement HPWSs and encourage workforce diversity to maximize the value of CSR activities and ensure their sustainability.

Background: During the pandemic, Emergency departments were overcrowded with critically ill patients and confronted ethical dilemmas to assign respiratory support to them due to scarce resources. Quick tools to evaluate patients at admission were needed; many scores were used but inaccurate to predict outcomes. The Rox Index is an easy and fast score that reflects the respiratory status in acute respiratory failure patients, this score could predict the outcome of covid 19 patients. Hypothesis: The 24-hour difference in the Rox Index discriminate accurately the mortality and needs for mechanical ventilation of patients with covid-19. Methods: Study design: Prospective analytic study. Population: 204 Patients admitted to the emergency department from May to August 2020. Data were collected from the clinical records. The Rox Index was calculated at admission and 24h later, the difference was used to establish the outcome, a logistic regression model adjusting for age, sex, presence of comorbidities and disease severity to build and perform ROC analysis. Results: Difference in respiratory ROX Index between admission and 24h is a good predictor for death AUC 0.92 and for mechanic ventilation AUC: 0.75. Each decrease in one unit of the difference at 24h had an Odds Ratio for death risk: 1.48 (95%CI: 1.31-1.67) and for mechanic ventilation: 1.16 (95%IC: 1.1-1.23). Conclusion: The 24-hour variation of Rox Index has good predictive value and allows healthcare professionals to identify which patients will benefit from invasive treatment, especially in low resource settings where emergency physicians deal with survival.

The structural, elastic, and electronic properties of orthorhombic Cd2SiO4 and Hg2GeO4 were examined under varying pressure conditions using first-principles calculations based on densi-ty-functional theory employing the projector augmented wave method. The obtained cell pa-rameters at 0 GPa were found to align well with existing experimental data. We delved into the pressure-dependence of normalized lattice parameters and elastic constants. In Cd2SiO4, all lat-tice constants decreased as pressure increased, whereas in Hg2GeO4, parameters a and b de-creased while parameter c increased under pressure. Employing the Hill average method, we calculated the elastic moduli and Poisson’s ratio up to 10 GPa, noting an increase with pressure. Evaluation of ductility/brittleness under pressure indicated both compounds remained ductile throughout. We also estimated elastic anisotropy and Debye temperature under varying pres-sures. Cd2SiO4 and Hg2GeO4 were identified as indirect band gap insulators, with estimated band gaps of 3.34 eV and 2.09 eV, respectively. Interestingly, Cd2SiO4 exhibited a significant increase in band gap with increasing pressure, whereas the band gap of Hg2GeO4 decreased under pres-sure, revealing distinct structural and electronic responses despite their similar structures.

In the digital era, enhancing the heritage resources of a tourist route means describing and networking them to promote their visibility and attractiveness. Prior studies mainly assess mountainous region’s natural resources through multi-indicator descriptive evaluation. This study aims to develop a comprehensive measurement of indicator’s value while assessing the tourism development potential of mountainous rural area. It concerns the main tourist route of the UNESCO M'Goun Geopark, located in the central High Atlas of Morocco. It also involves analyzing the criteria for choosing this destination by segmenting tourists' consumption experiences. Statistical analysis of the collected data reveals five dimensions of destination choice and four visitor groups. This article proposes to discuss findings and their applicability in terms of tourism destination management and decision-making, which can help local governments to rationally allocate tourism resources and land use.

To facilitate the computation of the uniaxial compressive strength value of the cemented paste backfill under the condition of high sand-cement ratio, and to analyze the size effect of the cemented paste backfill with high sand-cement ratio under varied aspect ratios, the cemented paste backfill specimens with sand-cement ratios of 8:1-24:1 and aspect ratios of 0.5, 1, and 2 were prepared. Through response surface experiments and finite element analysis, the influence of three aspect ratios on the cemented paste backfill strength was explored, and the failure characteristics and size effect mechanisms of cemented paste backfill with various aspect ratios were analyzed. The model of strength conversion between cemented paste backfill with different aspect ratios was established. The results show that the compressive strength of the cemented paste backfill decreases with the increase of the aspect ratio under the same mass concentration and sand-cement ratio. When the aspect ratio is 0.5 and 1, the splitting failure is the main factor; when the aspect ratio is 2, the shearing failure is the main factor. The three-dimensional stress caused by the end effect of the cemented paste backfill is the main reason for the high strength when the aspect ratio is 0.5. Due to the one-dimensional stress zone generated in the middle of the cemented paste backfill with an aspect ratio of 2 in the laboratory, its strength value is closer to the actual uniaxial compressive strength value of the cemented paste backfill. The strength values of the cemented paste backfill with aspect ratios of 0.5 and 1 were higher than the actual uniaxial compressive strength values in the laboratory. The rationality of the theoretical analysis was verified by the ABAQUS analysis results. According to the experimental results, a strength conversion model between different aspect ratios is established, which can provide a reference for the design of the uniaxial compressive strength of the cemented paste backfill.

Purposes: Engaging in regular physical activity has been consistently linked to improved physical health and academic performance. Despite its known benefits, there is a concerning trend of decreased physical activity among children globally. The study primarily aims to investigate the level of physical activity among junior high school students in Taiyuan and analyze the main affecting factors from a socio-ecological perspective. Methods: A cross-sectional study was conducted, involving 650 junior high school students from 7 schools in Taiyuan, and 648 valid questionnaires were collected. Physical activity levels were assessed using the Children’s Leisure Activities Study Survey Questionnaire. Factors influencing physical activity were evaluated through the Student Perceived Factors Affecting Physical Activity Questionnaire. Results: In this study, students from the 7th, 8th, and 9th grades participated in physical activities, averaging 214.5 minutes per week in moderate-intensity and 25 minutes in high-intensity activities, cumulatively averaging 280 minutes weekly. Notably, a significant disparity (p<0.05) was observed in the combined duration of moderate and high-intensity activities, with male students engaging more time compared to their female counterparts (307.500 vs 255.000 minutes). This variance extended across different grades, particularly evident in 8th graders who recorded the highest weekly high-intensity activity duration (31.000 minutes) and overall physical activity time (320.500 minutes), surpassing the 7th graders. Furthermore, an exploratory factor analysis of a 32-item questionnaire, designed to identify determinants of physical activity, revealed six principal components. These components were found to positively correlate with both moderate and high-intensity physical activities. Conclusion: This study emphasizes the necessity for educational institutions and community programmes to provide engaging physical activities, especially during weekends. It highlights the importance of tailoring physical education curricula to address gender and grade differences and investing in quality sports equipment and facilities by schools and local governments.

Experimental investigations were conducted to uncover the impact of cavitation control - through the use of riblets (mesoscale surface structuring) - on cavitating flows around a circular cylinder. First, the dynamics of cavitation in the flow behind a finite cylinder (without riblets) was unveiled by visualizing the cavitation clouds and measuring the lift force fluctuations acting on the cylinder. Second, as a significant step forward, a comprehensive explanation was provided for the mechanism of cavitation control using two bio-inspired riblet morphologies positioned in different orientations and locations on the cylinder. For the first time, the effects of these tiny structures on the flow dynamics and the associated cavitation process were scrutinized. This showed that scalloped riblets, with their curved design, induced secondary vortices near their tips and distorted primary streamwise vortices, and that high velocity gradients near the jagged pattern peaks of sawtooth riblets delayed flow separation, which affected cavitation.

Genetic engineering and directed evolution are effective methods to address the low yield and poor industrialization level of microbial target products. The current research focus is on how to efficiently and rapidly screen beneficial mutants from constructed large-scale mutation libraries. Traditional screening methods such as plate screening and well plate screening are severely limited in their development and application due to their low efficiency and high costs. In the past decade, microfluidic technology has become an important high-throughput screening technology due to its fast speed, low cost, high automation, and high screening throughput, and it has developed rapidly. Droplet-based microfluidic high-throughput screening has been widely used in various fields such as strain/enzyme activity screening, pathogen detection, single-cell analysis, drug discovery, and chemical synthesis, and has been widely applied in industries such as materials, food, chemicals, textiles, and biomedicine. In particular, in the field of enzyme research, droplet-based microfluidic high-throughput screening has shown excellent performance in discovering enzymes with new functions, improved catalytic efficiency or stability, acid-base tolerance, etc. Currently, droplet-based microfluidic high-throughput screening technology has achieved high-throughput screening of enzymes such as glycosidase, lipase, peroxidase, protease, amylase, oxidase, and transaminase, as well as high-throughput detection of products such as riboflavin, coumarin, 3-dehydroquinate, lactic acid, and ethanol. This article reviews the application of droplet-based microfluidics in high-throughput screening, with a focus on high-throughput screening strategies based on UV, visible, and fluorescence spectroscopy, including labeled optical signal detection screening, as well as label-free electrochemical detection, mass spectrometry, Raman spectroscopy, nuclear magnetic resonance, etc. Furthermore, the research progress and development trends of droplet-based microfluidic technology in enzyme modification and strain screening are also introduced.

Cavitation resulting from underwater explosions in compressible multiphase or multicomp-onent flows presents significant challenges due to the dynamic nature of shock-cavitation-structure interactions, as well as the complex and discontinuous nature of the involved interfaces. Achieving accurate resolution of interfaces between different phases or components, in the presence of shocks, cavitating regions, and structural interactions, is crucial for modeling such problems. Furthermore, pressure convergence in simulations involving shock-cavitation-structure interactions requires accurate algorithms. In this research paper, we employ the diffuse interface method, also known as the interface capturing scheme, to investigate cavitation in various underwater explosion test cases near different surfaces; free surface and a rigid surface. The simulations are conducted using the Unstructured Compressible Navier-Stokes (UCNS3D) finite volume framework employing central-weighted essentially non-oscillatory (CWENO) reconstruction schemes, utilising the five-equation diffuse interface family of methods. Quantitative comparisons are made between the performance of both models. Additionally, we examine the effects of cavitation as a secondary loading source on structures, and evaluate the ability of the CWENO schemes to accurately capture and resolve material interfaces between fluids with minimal numerical dissipation or smearing. The results are compared with existing high-order methods and experimental data, where possible, to demonstrate the robustness of the CWENO schemes in simulating cavitation bubble dynamics, as well as their limitations within the current implementation of interface capturing.

Abstract: Objectives: To establish the expression profile of N6-methyladenosine(m6A) modifications in the hippocampus of mice with diabetic cognitive impairment (DCI) and elucidate the potential regulatory mechanism. Methods: A DCI model was established by feeding a high-fat diet to C57BL/6J mice. m6A and RNA sequencing was conducted to profile the m6A-tagged transcripts in the hippocampus. Results: Methylated RNA immunoprecipitation with next-generation sequencing and RNA sequencing analyses yielded differentially m6A-modified and expressed genes in the hippocampus of DCI mice, which were enriched in pathways involving synaptic transmission and axonal guidance. Mechanistic analyses revealed a remarkable change in m6A modification levels through alteration of the mRNA expression of m6A methyltransferases (METTL3 and METTL14) and demethylase (FTO) in the hippocampus of DCI mice. Conclusions: We identified a co-mediated specific RNA regulatory strategy that broadens the epigenetic regulatory mechanism of RNA-induced neurodegenerative disorders associated with metabolic and endocrine diseases.

In order to utilize high-alumina coal gangue (HACG) as auxiliary cementitious admixture, it is of fundamental significance to thermally activating Al2O3 effectively in HACG and promoting formation of hydratable products containing Al2O3. In this paper, a new preparation technology is developed to make HACG auxiliary cementitious admixture by thermal activation of HACG-Ca(OH)2 (CH) mixture. HACG powders mixed with 20wt.% CH were calcined within a temperature range of 600-900oC, the thermal transformation and mineral phase formation were analyzed by thermogavimetric analyzer (TGA), X-ray diffractometer (XRD), scanning electron microscope (SEM) and energy dispersive X-ray spectrometer (EDS). The hydration reaction between activated HACG-CH mixture and cement was also investigated. HACG experienced a conventional transformation from kaolinite to metakaolin at 600oC and finally to mullite at 900oC. However, CH underwent an unexpected transformation process from CH to CaO, then to CaCO3, and finally to CaO again with increasing calcining temperature. These substances states were associated with dehydroxylation of CH, chemical reaction between CaO and CO2 generating from combustion of carbon in HACG, and decomposition of CaCO3, respectively. It is the formation of a large amount of CaO above 800oC that favors the formation of hydratable products containing Al2O3 in the calcining process and C-A-H gel in hydration process. The mechanical properties of HACG-cement mortar specimens were measured, from which the optimal calcination temperature for preparing HACG auxiliary cementitious admixture was determined to be 850oC. As compared with pure cement mortar specimens, the maximum 28-d flexural and compressive strength of HACG-cement mortar specimens increased by 5.4% and 38.2%, respectively.

The effects of rare earth Y content on the microstructure and high-temperature oxidation properties of 47Fe-36Ni-15Cr-1.5Mn alloy at 1000°C were investigated. The results show that 47Fe-36Ni-15Cr-1.5Mn alloy oxidizes at 1000°C under laboratory atmospheric pressure to form an oxide film layer dominated by Cr2O3 and (Fe, Ni, Mn) Cr2O4 spinel, and the oxidation curve of the alloy follows the parabolic law. After the addition of rare earth Y, rare earth phases precipitated along the grain boundaries in the alloy, and the more Y content, the more precipitated phases in the grain boundaries. The alloy with added rare earths was oxidized at a high temperature of 1000 °C for 2160 min, the oxidation law still followed the parabolic law, while the rare earth phase at the grain boundary reacted with the oxygen atoms infiltrated from the outside to generate a rare earth Y-rich oxide residing at the boundary between the grain boundary and the precipitated phase of the alloy. Add 0.5 wt.% rare earth Y 47Fe-36Ni-15Cr-1.5Mn-0.5Y alloy 1000 ° C high temperature oxidation of the formation of spinel oxide crystalline particles, dense and complete oxide film layer, the surface of the addition of a small amount of (0.5 wt.%) rare earth Y after the refinement of the oxide particles, and in the alloy grain boundaries in the form of oxides reside in the alloy to inhibit the cations in the matrix and the oxygen negative ions. and oxygen-negative ions in the alloy matrix, improving the antioxidant performance of the alloy. With the further increase of rare earth Y, during the oxidation of the alloy at high temperature, the precipitation phase at the grain boundary promotes the inward diffusion of oxygen, resulting in the deterioration of the antioxidant property of the alloy.

The aeroelastic response of lightweight low-speed aircraft with slender wings under extreme flow turbulence intensity is not well-understood. Experiments on a commmercial unmanned aerial vehicle (UAV) with a 3-meter wingspan and aspect ratio of 13.6 were performed in a large open-return wind tunnel with extreme flow turbulence intensity of T∞≈10%. The structural dynamics of the wing in the bending mode and the flow beneath the wing to capture the effect of aileron deflection was measured using laser displacement sensors and tomographic particle image velocimetry (PIV) techniques. The unsteady lift produced by the wing was also measured using a high-capacity load cell at an angle of attack, α of 2 degrees for three freestream velocities U∞ of 13.4 m/s, 17.9 m/s, and 26.8 m/s representing the UAV’s stall through cruise speed. It was found that high flow turbulence intensity with large integral length scales relative to the wing chord plays a dominant role in the large unsteady lift and wing displacements measured. The power spectral density (PSD) of wing structural vibration shows that flow shedding from the wing and the integral length scales have a significant impact on the overall power inherent in the bending vibration of the wing. Computation of vorticity iso-surfaces in the flow measurement volume surrounding the aileron reveal a striking observation; aileron deflection, δa of 10∘becomes less effective in producing additional spanwise vorticity, which is proportional to circulation and lift, at U∞ of 26.8 m/s because the freestream already has elevated levels of vorticity. A paradigm shift in design is suggested for light aircraft structures with slender wings operating in highly turbulent flow, which is to employ multiple control surfaces in order to respond to this flow and mitigate large bending or torsion displacements and the probability of structural failure.

Bandsaw blades are typical band-shaped cutting tools characterized by a low stiffness and micro-level cutting depth, resulting in distinct wear mechanisms compared to rigid cutting tools. In this study, the evolution of bandsaw tooth wear mechanisms during the bandsawing of Cr12MoV cold-working steel was investigated. The tool life was divided into two stages according to the tooth wear mechanism: a rapid wear stage (Stage I) and a homogeneous wear stage (Stage II). In Stage I, the wear mechanism was dominated by chipping, although multiple wear mechanisms were found because of the relatively poor manufacturing tolerance compared to rigid cutting tools, resulting in remarkable differences between the cutting depths of the individual teeth. In Stage II, abrasive and adhesive wear were the primary wear mechanisms instead of chipping, due to the decreased width and setting magnitude tolerance after Stage I. Furthermore, methods for increasing the bandsaw performance were proposed based on the tooth wear mechanisms.

Obesity and overweight are associated with many metabolic diseases, such as hypertension, diabetes, and dyslipidemia, which are closely related to a sedentary lifestyle and lack of exercise. Aerobic exercise effectively increases the high-density lipoproteins-cholesterol (HDL-C) levels and decreases the triglyceride (TG) levels. The consumption of Cuban policosanol (Raydel®) is also effective in enhancing the HDL-C quantity and HDL functionality to treat dyslipidemia and hypertension. On the other hand, no study has examined the effects of a combination of high-intensity exercise and policosanol consumption in obese subjects to improve metabolic disorders. In the current study, 17 obese subjects (average BMI 30.0±1.1 kg/m2, eight male and nine female) were recruited to participate in a program combining exercise and policosanol (20 mg) consumption for 12 weeks. After completion, their BMI, waist circumference, total fat mass, systolic blood pressure (SBP), and diastolic blood pressure (DBP) decreased by approximately 15% (p=0.022), 12.7% (p=0.008), 33% (p=0.006), 11% (p<0.046), and 13% (p=0.007), respectively. In the serum lipid profile, at week 12, they showed a remarkable decrease in the total cholesterol (TC) and triglyceride (TG) levels, up to 17% (p<0.019) and 54% (p<0.002) from the baseline, respectively. Although the serum HDL-C was increased by approximately +12% from the baseline, the percentage of HDL-C in TC, HDL-C/TC (%), was increased by up to +32% (p=0.007) at week 12. The serum coenzyme Q10 (CoQ10) level was increased 1.2-fold in all participants at week 12 from the baseline. In particular, the male participants showed a 1.4-fold increase (p=0.027) from the baseline. The larger increase in serum CoQ10 was correlated with the larger increase in the serum HDL-C during 12 weeks. The hepatic function parameters were improved; the serum -glutamyl transferase decreased at week 12 by up to 55% (p<0.007), while the aspartate aminotransferase and alanine transaminase levels decreased within the normal range. In the lipoprotein level, the extent of oxidation and glycation were reduced significantly in VLDL and LDL, with a remarkable decrease in the TG content in particles. The antioxidant abilities of HDL2 and HDL3, such as paraoxonase (PON) and ferric ion reduction ability (FRA), were enhanced significantly by up to 1.8-fold (p<0.001) and 1.6-fold (p<0.001) at week 12. The particle size and number of HDL2 were increased up to +10% during the 12 weeks with a remarkable decrease in the TG content, glycation extent, oxidation up to 32% (p=0.032), 18% (p=0.043), and 11% (p=0.023), respectively. The particle number and diameter of HDL3 were increased by up to +9% with a remarkable increase in the PON activity, FRA activity, and TC content of +82% (p<0.001), +56% (p<0.001), and +32% (p=0.009), respectively. Expression of apolipoproteinA-I in HDL2 and HDL3 were significantly elevated more in both gender around 30~48% with more distinct band intensity and less glycation at week 12. These improvements in HDL quality and functionality were linked to the higher survivability of adult zebrafish and their embryos. Under the co-presence of carboxymethyllysine (CML), a microinjection of HDL2 to zebrafish embryo from week 0 resulted in approximately 47% survivability with developmental defects and attenuated speed. On the other hand, the HDL2 microinjection from week 12 resulted in remarkably higher survivability (~ 70%). In conclusion, 12 weeks of Cuban policosanol (Raydel®, 20 mg) consumption with high-intensity exercise showed significant improvement in blood pressure, body fat mass, blood lipid profile without liver damage, CoQ10 metabolism, and renal impairment. At week 12, all participants showed a remarkable decrease in oxidation and glycation extent in the VLDL and LDL with a decrease in the TC and TG content. Significant enhancement of the qualities and functionalities in HDL2 and HDL3 by the policosanol consumption were also detected: increase in apoA-I content, TC content, particle size, and particle numbers along with antioxidant abilities, such as PON and FRA.

Carbonization of a biopolymer (lignin) in self-propagating high-temperature synthesis (SHS) led to the production of 2D graphene structures. With the help of modern analytical methods (Raman spectroscopy, X-ray diffraction) and electron microscopy, the resulting product was confirmed to have a few-layer 2D graphene structure. The predicted photovoltaic properties of the resulting few-layer graphene were implemented for laser ignition of a model pyrotechnic composition based on porous silicon. A phenomenological model of the formation mechanism of 2D graphene structures under the conditions of the SHS process is proposed.

A twin-screw extruder was used to fabricate poly(butylene succinate) (PBS)/high density polyethylene (HDPE) blends (7:3 weight ratio) and blend-based nanocomposites. Carbon nanotubes (CNTs), graphene nanoplatelets (GNPs) and organoclays (15A and 30B) served as the nanofiller, while maleated HDPE (PEgMA) acted as an efficient compatibilizer for the blend. In the composites, individual nanofillers were mostly localized in HDPE domains, but some fillers were also observed at PBS-HDPE interfaces. The sea-island morphology of compatibilized blend evolved into a pseudo-co-continuous morphology in the composites. Differential scanning calorimetry results confirmed that PEgMA with HDPE evidently accelerated the crystallization of PBS in the blend. The possible nucleation effect of added fillers on PBS crystallization was obscured by the formation of quasi-connected HDPE domains, causing less PBS nucleation sites. The presence of nanofillers improved the thermal stability and burning anti-dripping behavior of the parent blend. The anti-dripping efficiency of added fillers followed the sequence: CNT>15A>30B>GNP. Rigidity of the blend was increased after formation of nanocomposites. In particular, adding GNP resulted in 31% increase in flexural modulus. Development of a pseudo-network structure in the composites was confirmed by measurement of rheological properties. Electrical resistivity of the blend was reduced by more than 6 orders of magnitude at 3 phr CNT loading, demonstrating the achievement of double percolation morphology.

Ornamental kale (Brassica oleracea var. acephala) is an attractive ornamental plant with a range of leaf colors and shapes. Breeding new varieties of ornamental kale has proven challenging due to its lengthy breeding cycle and the limited availability of genetic markers. Microspore culture is an effective approach to generate new materials and genetic maps are a prerequisite for quantitative trait loci analysis, MAS, fine gene mapping, and genome sequence assembly. In this study, a F1DH ornamental kale population comprising 300 DH lines was constructed using microspore culture. A high-density genetic map was developed by conducting whole-genome sequencing on 150 individuals from the F1DH population. The genetic map contained 1,696 bin-markers with 982,642 single-nucleotide polymorphisms (SNPs) spanning a total distance of 775.81 cM on all nine chromosomes with an average distance between markers of 0.46 cM. The ornamental kale genetic map contained substantially more SNP markers compared with published genetic maps for other B. oleracea crops. The F1DH progenies provide an excellent resource for germplasm innovation and breeding new varieties of ornamental kale. The high-density genetic map provides crucial insights for gene mapping and unraveling the molecular mechanisms behind important agronomic traits in ornamental kale.

A 4×2 factorial experiment was conducted to evaluate the potential of feeding dietary gamma-oryzanol and vitamin E tocotrienols in hens reared in 840 (low cage density; LCD) or 420 cm2/hen (high cage density; HCD). A total of 120 hens were allocated into eight groups with five replicates. Diets were a control (CON) or the control diet supplemented with 200 ppm gamma-oryzanol (GO-200), 200 ppm vitamin E tocotrienols (VE-200) or 200 ppm gamma-oryzanol + 200 ppm vitamin E tocotrienols (GE-400). Results showed that HCD-housed hens decreased (P &lt; 0.01) egg performance and quality. Average egg weight (AEW), egg mass and FCR improved in all supplemented treatments. Results on the AEW, FCR, and eggshell qualities of birds kept at the HCD revealed the best responses in the GE-400 group (P &lt; 0.01). Among hens kept on an HCD, there was a noticeable decrease in HMGCR mRNA abundance in the VE-200 group, while the highest IFN-γ mRNA abundance was found in hens fed the GO-200 diet (P &lt; 0.05). Thus, this study suggested that dietary GO or VE at 200 ppm either individually or in combination could improve performance and egg quality as well as regulate the abundance of immune- and stress-related genes.

Staphylococcus aureus is a common pathogen in human. Methicillin resistant Staphylococcus aureus (MRSA) infection poses a big and perplexing difficulty in terms of therapy. The acquisition of the non-native gene PBP2a, which has a decreased tolerance for β-lactam antibiotics, frequently confers resistance. PBP2a has a less attraction for methicillin and it helps bacteria to continue peptidoglycan biosynthesis, and it is cell wall’s core component in bacteria. So, even in the presence of methicillin or any other antibiotic, bacteria develop resistance. Due to resistance-causing genes, S. aureus becomes MRSA. The main premise of the resistance mechanism is well understood. The current demand for novel antibiotics is legitimate in the face of therapeutic concerns posed by resistant micro-organisms. The emphasis of this review is on PBP2a scaffolds and the different screening approaches used to find PBP2a inhibitors. Penicillin, Cephalosporins, Pyrazole-Benzimidazole based derivatives, Oxadiazole containing derivatives, non-β-lactam allosteric inhibitors, 4-(3H)-Quinazolinones, Pyrrolylated chalcone, Bis-2-Oxoazetidinyl macrocycle (β-lactam antibiotics with 1, 3-Bridges), Macrocycle-embedded β-lactams as novel inhibitors, Pyridine-Coupled Pyrimidinones, novel Naphthalimide corbelled aminothiazoximes, non-covalent inhibitors, Investigational-β-lactam antibiotics Carbapenem, novel Benzoxazole derivatives, Pyrazolylpyridine analogues, and other miscellaneous classes of scaffolds for PBP2a are also represented as well as with their biological activity is discussed. The penicillin-binding protein is also discussed, which is the crucial target for the cell wall of MRSA. Various aspects of PBP2a, the cell wall of bacteria, peptidoglycans, different crystal structures of PBP2a, synthetic routes for PBP2a inhibitors, and future perspectives of MRSA inhibitors are also enumerated.

Abstract: An Al-Co-Y diffusion coating was prepared on a TiAl alloy by pack cementation process at a low temperature range of 650-720 ℃. The influence of different activators and co-deposition temperatures on the coating’s microstructure and formation process, and high temperature oxida-tion performance was studied. The results showed that NaF was a more suitable activator for preparing the Al-Co-Y diffusion coating on TiAl alloy compared to NH4Cl and AlCl3. A more compact coating structure can be obtained when deposition was performed at 680 ℃ using NaF as the activator. The coating was mainly composed of a TiAl3 outer layer, a TiAl2 inner layer, and a thin Al-rich TiAl inter-diffusion layer. The growth of the coating exhibited a positive linear correlation between coating thickness increase and the square root of deposition time. The high-temperature oxidation tests showed that a dense scale mainly composed of Al2O3 and a small amount of TiO2 formed on the coating after oxidation at 950 ℃ for 100 h. The scale possessed excellent high-temperature oxidation resistance, with a parabolic rate constant of the oxidation weight gain approximately 4.9×10-3 mg2/cm4 h, which is lower than that of the TiAl substrate by about three orders of magnitude, and lower than that of the pure Al diffusion coating more than one order of magnitude.

Microemulsions with excellent properties have shown significant potential for enhancing oil recovery from tight formations through spontaneous imbibition. This work present a high-temperature-tolerant lower-phase microemulsion (HTLP-ME) using a microemulsion dilution method. The properties and morphological characteristics of HTLP-ME were evaluated and proposed a enhanced spontaneous imbibition oil recovery mechanism using imbibition tests and CT scanning technology. The results show that the optimum concentration of HTLP-ME is 0.2wt% has a superior thermal stability, small particle size, lower IFT, good wettability alteration ability, and minimum adsorption loss. Imbibition and CT experiments showed that the longer the imbibition distance, the better is the effect on spontaneous imbibition oil recovery. Furthermore, the solubilization coefficient and self-driving force were defined and calculated to quantitatively analyze the imbibition mechanisms. The imbibition mechanisms demonstrate that the reduction of oil/solid adhesion is due to the synergistic effect of IFT reduction and wettability alteration, and the ability to increase the imbibition distance through a larger self-driving force.

In order to study the acoustic emission characteristics of sandstone under the action of the high temperature-water cooling cycle, the RMT-150B electro-hydraulic servo rock test system and the DS-5 acoustic emission detection and analysis system were used to conduct a single analysis of the sandstone after the high temperature-water cooling cycle. Experimental study on acoustic emission characteristics under axial compression, analyzing the deformation, strength and acoustic emission characteristics of sandstone under different temperatures and cycles. The results of the study show that the high temperature-water cooling action causes changes in the physical properties of the sandstone. The expansion rate of the rock sample decreases first and then increases when the temperature rises, and the strength first increases and then decreases. The number of cycles has little effect on the physical properties of the rock sample; sandstone acoustic emission ringing count increases with the increase of temperature and cycle times, acoustic emission activities become more frequent with the loading process; with the increase of cycle times and temperature, acoustic emission ringing counts and accumulative acoustic emission energy appear earlier The rock sample enters the elastic deformation stage ahead of schedule, the yielding period increases, and the rock sample presents a trend of transition from brittle failure to ductile failure; the ringing count and cumulative energy increase with the increase in temperature and cycle times, and the high-energy ringing count and cumulative energy increase. The simultaneous sharp increase of the rock sample is the harbinger of the failure and instability of the rock sample.

The incorporation of polycarboxylate ether superplasticizer (PCE) type polymer and silica fume (SF) in high-performance concretes (HPC) leads to the achievement of remarkable rheological and mechanical improvements. In the fresh state, PCEs are adsorbed on cement particles and dispersants, in turn promoting the workability of the concrete. Silica fume enables a very well compacted concrete to be obtained, which is characterized by high mechanical parameters in its hardened state. Some PCEs are incompatible with silica fume, which can result in the loss of slump and in poor rheological behavior. The main objective of the research is the study of the influence of three types of PCEs, which all have a different molecular architecture, on the rheological and mechanical behavior of high-performance concretes containing 10% of SF as a partial replacement of cement. The results show that the carboxylic density of PCE has an influence on its compatibility with SF.

This paper proposes a novel symmetrical active-switched coupled-inductor high-step-up DC/DC converter. A new active-switched coupled inductor is used to allow much higher voltage gain of the proposed converter. The symmetrical circuit structure of the proposed converter evenly divides large input currents and reduce input current ripple by operating in interleaved mode so power density is increased. The switches also have low voltage stress. The operating principle and design considerations for the converter topology are described. The proposed converter with an input voltage of 40 V, an output voltage of 400 V and an output of 1000 W at a switching frequency of 50 kHz is implemented. The simulations and experimental results are thus depicted to verify the theoretical analysis. The highest efficiency is 95.5% at 200 W measured by using a HIOKI 3390. Consequently, the proposed converter is suitable for renewable energy generation systems that require high power, high voltage gain and high efficiency.

High-grade gliomas present a significant challenge in neuro-oncology because of their aggressive nature and resistance to current therapies. Boron neutron capture therapy (BNCT) is a potential treatment method; however, the boron carrier compounds used — such as 4-borono-L-phenylalanine (L-BPA) — have limitations. This study evaluated the use of boron-conjugated 4-iodophenylbutanamide (BC-IP), a novel boron compound in BNCT, for the treatment of glioma. Using in vitro drug exposure experiments and in vivo studies, we compared BC-IP and BPA, with a focus on boron uptake and retention characteristics. The results showed that although BC-IP had a lower boron uptake than BPA, it exhibited superior retention. Furthermore, despite lower boron accumulation in tumors, BC-IP showed significant survival improvement in glioma-bearing rats compared to controls. These results suggest that BC-IP, with its unique properties, may be an alternative boron carrier for BNCT. Further research is required to optimize this potential treatment modality, which could significantly contribute to advancing the treatment of high-grade gliomas.

At present, in the field of aviation industry, titanium alloy is mainly used to manufacture parts such as compressor disc, blade and casing of aircraft engine. When working, titanium alloy parts produce high temperature due to high-speed running friction, which makes the high temperature oxidation resistance and friction resistance of titanium alloy greatly reduced. When their working environment contains salt, titanium alloys are subjected to thermal corrosion, which limits their wider practical applications. This paper introduce the aluminide coating and its preparation methods. The characteristics and functional mechanism of three functional coatings for service environment, such as high temperature resistant alumina-based coating, thermal corrosion resistant alumina-based coating and wear-resistant alumina-based coating are summarized. Finally, the development direction of composite coatings of titanium and titanium alloys for complex service environment is prospected.

At Mae-Moh power plant, Thailand, superheater tubes, which are exposed in fly ash environ-ment, often degrade due to solid particle erosion. To extend the service lifetime of the superheater tubes, the high velocity oxy-fuel (HVOF) thermal spray technique is used to deposit a protective coating on the material, SA213-T22 steel. In this work, the solid particle erosion of the Co-28Cr and WC-12Co coatings was investigated using erodent particle impingement at the angles of 30o and 90o with an average particle size of 60 μm. The erosion behavior of SA213-T22 with and without Co-28Cr and WC-12Co coatings was explained using ductile and brittle erosion modes. The erosion test resulted in the brittle mode for both Co-28Cr and WC-12Co coatings, while SA213-T22 without coating indicated the ductile mode. On the investigation of surface morphology, the Co-28Cr coating showed mostly microcracks in contrast with the WC-12Co coating, fracture, de-bonding and deep cavities were also observed. Erosion resistance of the Co-28Cr coating was significantly higher than the WC-12Co coating, due to high hardness, low porosity and high density of the coating.

Limited availability of expensive alloying elements elevates low-alloyed steels to a unique position in the field of lightweight construction and mass production. Quenching and partitioning (Q&P) heat treatments of low-alloyed steels with exceptional property combinations are particularly promising. In this study, we characterize for the first time a new low-alloyed steel to be processed by Q&P heat treatments. In combined experimental and numerical studies, we design a novel approach that effectively combines the short cycle times of press hardening with the excellent property profiles of Q&P-treated steels. We identify appropriate transformation parameters for Q&P heat treatments by dilatometric studies and we adjust a number of reference conditions with different isothermal holding times. By means of SEM analysis and XRD measurements, we show that different fractions of retained austenite result in different mechanical properties. Initial numerical designs of the process can identify varying temperature profiles and cooling rates depending on the position in the die. The results show that the geometry of the part plays a minor role, but the die temperature is the dominant factor for successful partitioning directly in the press hardening process.

Hardaliye, a traditional non-alcoholic beverage, made from red grape pomace from wine production and produced by lactic acid fermentation with addition of different concentrations of whole/ground or heat-treated mustard seeds and of sour cherry leaves. Short shelf life of hardaliye limits its consumption and search in trend to process hardaliye to extend its shelf life. Thus, high hydrostatic pressure treatment of hardaliye drink with determination of changes in physicochemical and sensory properties in addition to microbial inactivation were studied according to Box-Behnken design. Maximum 5.10±0.00, 4.21±0.00, 5.38±0.59 and 5.05±0.22 log reductions were obtained in total mesophilic aerobic bacteria, total mold and yeast, Brettanomyces bruxellensis and Lactobacillus brevis by HHP. Shelf-life studies of the hardaliye samples were conducted with optimum processing parameters of 490 MPa, 29 oC for 15 min with the response variables of OD520 and inactivation of L. brevis. Both control and HHP treated samples were stored at 4 and 22 C for shelf-life studies. While control samples at 4 and 22 °C were spoiled at the 15th and 3rd days, HHP treated samples were spoiled after 108th and 228th days, respectively.

This article addresses the problem of contact voltage increase caused by the low frequency oscillation of the train-grid system in the phase-separation process of the EMU. The article establishes the EMU-contact line-traction substation model, reveals the mechanism of low-frequency oscillation, and obtains the relationship between the separation phase angle of the pantograph with line and low-frequency oscillations. Methods to suppress the over-voltage during the low-frequency oscillation are proposed. The study shows that when the power phase angle of the pantograph-line separation is within the range of 60°~90° and 240°~270°, the voltage amplitude in the neutral zone is larger, the maximum amplitude can reach 52.2kV, and low-frequency oscillation will occur in the neutral zone. When low frequency oscillation occurs, the contact line voltage in the neutral zone is mainly 1/3 power frequency (16.7Hz). After installing an RC suppression device in the neutral zone, when the EMU enters the neutral zone, the absolute value of the voltage peak drops to below 20 kV. Compared with the situation where the suppression device is not connected, the absolute value of the voltage peak is reduced by nearly 60%. The study provides a basis for the design of the neutral zone of the contact line and the selection of the high-voltage equipment of the EMU.

Multi-level direct networks fueled by the evolving technology of active optical cables and increasing pin-bandwidth achieve reduced diameters and cost, with high-radix switches. These networks, like Dragonfly, are becoming the preferred aspirants for extreme high-performance parallel machines such as exa-scale computing. In this paper, we introduce a Hyper Z-Tree topology, which deploys the Z-Tree, a variant of fat-tree, as a computing node of a Generalized Hypercube (GHC) configuration. The resulting configuration provides higher bisection bandwidth, lower latency for some applications and higher throughput. Furthermore, the levels of the fat tree offer several path diversities across the GHC dimensions, hence conceding a more fault tolerant architecture. To profit from these path diversities, we propose two adaptive routing algorithms, which are extensions to the routing algorithm suggested in HyperX topology. These two algorithms exhibit better latencies and throughput than the HyperX.

This paper investigates the use of contactless power ultrasonic excitation to decrease the electrical impedance of the weld in laser welding. The literature extensively documents the impact of em-ploying contact power ultrasonic excitation on the microstructure morphology and refinement of grain in the weld. This study involves characterizing an industrial High Power Ultrasound Transducer (HPUT) by determining the optimal distance and angle for contactless excitation of the fusion zone in the weld, aiming to achieve the maximum amplitude. Subsequently, the transducer is integrated into the laser welding system, resulting in the creation of an ultrasonic-assisted welding system. To find the improvement due to the contactless vibration assistance, the welding area was char-acterised by an impedance ohmmeter device. The results indicate an approximately 6 % im-provement in the welding quality in terms of the impedance value, an important parameter for battery pack welding. In response to the issue of overheating in the industrial transducer during prolonged welding operations, an alternative transducer was proposed to overcome this challenge. Further investigations are carried out by the alternative transducer to find the effect of different wave types, namely, shear and compressional waves, on the welding quality. The contact vibration can excite the plate approximately 50 times higher in acceleration amplitude than contactless ex-citation. Nevertheless, enhancements of 10% and 6% are observed in the impedance value when utilising compressional and shear waves, respectively, as compared to the results obtained with contactless vibration.

The petrogenesis of high Ba-Sr granitoids provide a great significance to penetrate the Proto-Tethys evolution in the North Qilian orogenic belt. This paper presents a combination of zircon U-Pb age, whole-rock major and trace element concentrations, and Sr-Nd-Hf isotopic data for Caowa high Ba-Sr dioritic intrusion from the eastern part of the North Qilian orogenic belt, aiming to decipher its petrogenesis and tectonic setting. LA-ICP-MS zircon U-Pb dating yields an emplacement age of 447±3 Ma for the Caowa intrusion, indicating a magmatic activity of the late Ordovician. The Caowa quartz diorites contain moderate contents of SiO2, MgO, Mg# and resultant high concentrations of Na2O+K2O, Fe2O3T and Al2O3, displaying calc-alkaline and metaluminous characteristics. Their relatively elevated Ba (up to 1165 ppm) and Sr (561 to 646 ppm) contents, with obvious enrichment in LILEs (e.g. Ba、Th、U) and depletion in HFSEs (e.g. Nb、Ta、Ti) resemble those of typical high Ba-Sr granitoids in subduction zone. Together with enriched Sr-Nd isotopic compositons[(87Sr/86Sr)i=0.7082−0.7086, εNd(t)= -5.1 to -4.9], and relatively extensive εHf(t) values (-13.2 to +8.5) of zircons, it suggests that these high Ba-Sr quartz diorites were derived from a mixture magma source between the ancient crust materials and the enriched lithospheric mantle metasomatised by fluid was released from subducted oceanic crust or sediment. Taking into account the ophiolites, high pressure metamorphic rocks and arc magmatic rocks in the region, we infer that affected by the northward subduction of the Qilian Proto-Tethys ocean, the Laohushan oceanic crust of the North Qilian back-arc basin was subducted during the Late Ordovician and resulted in extensive metasomatism of lithospheric mantle by fluids derived from oceanic crust or sediments, and the Caowa high Ba-Sr quartz diorites generated in the process of crust-mantle interaction during the Late Ordovician.

INTRODUCTION There have been several advances in the treatment of hepatitis C virus (HCV) infection which have resulted in major reductions in the morbidity and mortality from liver-associated disease. These are not widely available in the Caribbean, due in part, to lack of knowledge of the epidemiology of infections with HCV. As efforts are made to eliminate HCV from the region, these and other existing barriers such as lack of an established database on HCV must be addressed. This review seeks to identify gaps in the knowledge of HCV in the Caribbean with respect to seroprevalence, genotype distribution and general epidemiologic characteristics. MATERIALS AND METHODS The literature for the period January 1, 2005, to October 2022, was reviewed to gather country specific data on HCV across the Caribbean. References were identified through indexed journals accessed through established databases. The usage pattern of HCV drugs was determined from data obtained from Pharmacists and Infectious Diseases Specialists across the region. RESULTS The prevalence of HCV in the Caribbean was 1.5%; the region should therefore be considered an area of moderate prevalence. Notably, data from specific countries were limited. The prevalence of HCV among intravenous drug users (21.9-58.8%); persons living with HIV/AIDS (0.8 to 58.5%); prisoners (32.8-64%) and men who have sex with men (MSM) (0.8-6.9%) was generally higher than in the general population (0.8-2.3%). Genotype 1 (83% was most prevalent followed by genotypes 2 (7.2%) and 3(2.1%), respectively. Drugs currently being used for treatment of HCV infections across the Caribbean include Epclusa (Sofosbuvir/velpatasvir), and Harvoni (Ledipasvir/sofosbuvir). Some of these drugs, are only available in the private sector and are sourced externally whenever needed. CONCLUSION There is a paucity of current data on the seroprevalence of HCV in the Caribbean and well-designed prospective studies are indicated to drive the implementation of treatment and control programs for HCV in the region. Barriers which need to be first overcome include unavailability and high cost of drugs used to treat HCV infections, injecting drug use and limited access to medical care and laboratory testing.

Abstract: The high entropy alloy (HEA) of equiatomic composition CrNiFeCoMn and with FCC 11 crystal structure was prepared by either induction melting and additive manufacturing with a se- 12 lective laser melting (SLM) process, starting from mechanically alloyed powders. Unlike induction 13 melting, the as-produced SLM alloy showed fine nitride and Cr-rich s phase precipitates. Mechan- 14 ical spectroscopy measurements were performed on specimens cold worked and/or recrystallized. 15 Young’s modulus values of (140±10) GPa and (90±10) GPa were measured at 300 K for induction 16 melted and SLM samples, respectively. The values increased to (160±10) GPa and (170±10) GPa for 17 recrystallized samples. Damping measurements as a function of temperature showed two peaks 18 which were attributed to dislocations bending and grain boundaries sliding. The peaks were super- 19 posed on a temperature increasing background.

Several studies have reported a relationship between autonomic dysfunction　 during tasks and Internet addiction. Changes within 24 h regarding heart rate variability (HRV) may be a more sensitive indicator than short term observations. We evaluated the influence of excessive Internet usage on HRV using a 24 h electrocardiogram (ECG) and examined acute changes during computer game tasks. A total 13 high school students and 22 young adults were recruited, and divided into excessive Internet user and non- excessive user groups based on Internet addiction test scores. The ECG was recorded continuously for 24 h by a wearable sensor and during two computer games (the Iowa gambling task and each participant’s preferred game) using a standard type ECG system. Multiple psychometric tests were also conducted. The excessive Internet user group exhibited clinically significant depressive symptoms, and higher self-reported scores for anxiety, impulsivity, autistic tendencies, and sleep problems than the non- excessive internet user group. There were weak differences within the 24 h high-frequency (HF) band power between two groups. During the Iowa gambling task, younger participants exhibited a reduced HF response, which may be related to weaker top- down self- regulatory mechanisms.

In engineering practice, various types of information data are affected by many factors during the collection process. For example, information data measurement errors are caused by equipment performance and the working environment. During the transmission of detection information, the signal distortion caused by energy loss and signal interference causes unpredictable detection errors in the collected information data. Through the study of fractional calculus theory, it was found that it is suitable for studying nonlinear, non-causal, and non-stationary signals, and has the dual functions of improving detection information and enhancing signal strength. Therefore, under the influence of many factors, we applied the fractional difference algorithm to the field of information data processing. Multi-sensor detection data fusion algorithm based on the fractional partial differential equation was adopted to establish its online detection data. A multi-sensor detection data fusion algorithm based on a fractional partial differential equation is established, which effectively fuses the information data detection errors caused by various influencing factors and greatly improves the detection accuracy of information data. The effectiveness of this method is proved through its application in an experiment.

To create normative scores for all CrossFit® Open (CFO) workouts and compare male and female performances, official scores were collected from the official competition leaderboard for all competitors of the 2011-2022 CFO competitions. Percentiles were calculated in athletes (18 – 54 years) who completed all workouts within a single year ‘as prescribed’ and met minimum scoring thresholds. Independent t-tests revealed significant (p &lt; 0.05) sex differences for 56 of 60 workouts. In workouts scored by repetitions completed, men completed more repetitions in 18 workouts by small-to-large differences (d = 0.22-0.81), whereas women completed more repetitions in 6 workouts by small-to-medium differences (d = 0.36-0.77). When workouts were scored by time-to-completion, men were faster in 10 workouts by small-to-large differences (d = 0.23-1.12), while women were faster in three workouts by small differences (d = 0.46). In three workouts scored by load lifted, men lifted more weight by large differences (d = 2.00-2.98). All other differences were either trivial or not significant. Despite adjusted programming for men and women, the persistence of performances differences across all CFO workouts suggest resultant challenges are not the same. These normative values may be useful to training and research in male and female CrossFit® athletes.

New nanocomposite material was prepared by high pressure processing of starting glass of nominal composition NaFePO$_{4}$. Thermal, structural, electrical and dielectric properties of the prepared samples were studied by differential thermal analysis (DTA), X-ray diffraction (XRD) and broadband dielectric spectroscopy (BDS). It was demonstrated that high pressure – high temperature treatment (HPHT) led to an increase of electrical conductivity of initial glasses by 2 orders of magnitude. It was also shown that the observed effect was stronger than for lithium analogue of this material studied by us earlier. The observed enhancement of conductivity was explained by Mott’s theory of electron hopping, which is more frequent in sample after pressure treatment. The final composite consisted of nanocrystalline NASICON and alluaudite phases, which are electrochemically active in potential cathode materials for Na batteries. Average dimensions of crystallites estimated from XRD studies were between 40 and 90 nm, depending on the phase. Some new aspects of local dielectric relaxations in studied materials were also discussed. It was shown that a combination of high pressures and BDS method is a powerful method to study relaxation processes and molecular movements in solids. It was also pointed out that high-pressure cathode materials may exhibit higher volumetric capacities compared with commercially used cathodes with carbon additions.

Canola is the major oilseed crop of Canada. The de-oiled material is an important by-product due to its rich phenolic profile and high protein content. This co-processing stream from canola is primarily utilized as animal feed but represents an invaluable source of nutraceuticals. Microwave-assisted solvent extraction (MAE), as a green extraction method, has received considerable attention in recent times. The ease of use and application of many solvents at the same time makes the MAE one of the best methods for studying multiple solvents at the same time. The formation of canolol, from sinapine and sinapic acid, is primarily dependant on temperature which favors the decarboxylation reaction. Hence, MAE using green extractants can be used to enhance the yield of canolol. This study examined the effects of different pre-treatment temperature-time combinations of 140, 150, 160, and 170℃ for 5, 10, 15, 20 and 30 minutes on the extraction of canolol and other canola endogenous phenolic compounds. Three antioxidant assays assessed the antioxidant activity of the different extracts obtained by MAE confirming the microwave as a novel and versatile instrument for enhancing the yield of canolol. Improvements in the antioxidant activity of the different extracts further established the efficacy of the current method for isolating important natural phenolic derivatives for utilization by the nutraceutical industry.

Bauxite residue (BR), also known as red mud, is a by-product of the production of alumina via the Bayer process. Because of the high sodium oxide and other impurities content, this material is not used to obtain iron or other iron-containing products. In this paper, the hydro-chemical conversion of goethite (FeOOH) to magnetite (Fe3O4) in high-iron BR from the Friguia alumina refinery (Guinea) by Fe2+ ions in highly concentrated alkaline media was studied. The simultaneous extraction of Al and Na made it possible to obtain a product containing more than 96% Fe3O4. The results show that the magnetization of Al-goethite and Al-hemetite accelerates the dissolution of the Al from the iron mineral solid matrix and from the desilication product (DSP). After ferrous sulfate (FeSO4·7H2O) was added directly at the FeO:Fe2O3 molar ratio of 1:1 at 120 °C for 150 min in the solution with the 360 g L-1 Na2O concentration, the alumina extraction ratio reached 96.27% for the coarse bauxite residue size fraction (Sands) and 87.06% for fine BR obtained from red mud. The grade of iron (total iron in the form of iron element) in the residue can be increased to 69.55% for Sands and 58.31% for BR. The solid residues obtained after leaching were studied by XRD, XRF, TG-DTA, VSM, Mössbauer spectroscopy and SEM to evaluate the conversion and leaching mechanisms and the recovery ratio of Al from different minerals. The iron-rich residues can be used in the steel industry or as a pigment.

Drought and high temperature often occur simultaneously will eventually affect rice (Oryza sativa L.) yield and seed quality. The objective of the study was to compare the effects of high temperature (HT) and water limitation (WL) during seed development and maturation on yield component, seed quality, and amylose content in aerobic rice cv. MRIA. Two experiments were conducted concurrently in greenhouse with ⁓35/26℃ subjected to elevated HT and/or WL; 5 days 38/28°C at 10, 15, 29 DAA and/or HT; 7 days at 40/28℃ at 8 and 21 DAA with 12h photoperiod in control environment growth chamber. Both experiments were respectively harvested at physiological maturity of 31 and 35 DAA. Grain yielded from the irrigated plant declined from over 27% to below 18% between 15 and 29 DAA. Combination stresses resulted in greater reduction of grain yield than single stress. Late seed development (29 DAA) had no effect either on yield component or seed quality as well as produce a high concentration in amylase content (16.7%) with greater germination capacity (91%). The non-stress plant harvested at 21 DAA resulted the highest percentage of germinated seeds (97%) whereas the vigour index (VI) was reduced to 70.3% and 58.9% at 8 and 21 DAA respectively. Extended plant stress to 7 consecutive days incurred the highest VI with low concentration of amylose content. There was a linear relationship incurred between seed amylase content with germination capacity and VI, however, there was an inverse relationship (R2 = 0.19) between amylase content with VI from plant treated with (HT and/or WL) for 7 days. The present results confirmed that the avoidance HT and WL during early (10 DAA) and mid (15 DAA) seed development with short duration of stress (5 days) obtained better in yield component, enhanced the seed quality and amylose concentration. The combined HT and WL damaged seeds’ quality were more than each stress alone. Therefore, avoiding HT and WL can be practically applied by farmers by irrigating throughout the rice plant during histodifferentiation to save water usage during seed maturation.

The article is devoted to identifying promising research issues on the topic of Digital Industry based on the analysis of bibliometric data from Scopus platform for 2018–2022. The definition of promising issues derived from the titles, additionally abstracts, of highly cited works by authors with high publication activity. Authors' Scopus profiles were used to determine their affiliations, which are important for in-depth analysis of selected promising Digital Industry tasks. Metadata filtering to identify highly cited papers on particular issues was performed by keywords, Subject Areas, affiliations with countries and sponsoring organizations. Additionally, bibliometric metadata were clustered based on the co-occurrence of terms using VOSviewer. Within these clusters, articles of interest were identified for the formulation of promising research issues on the topic of Digital Industry, which will be subjected to in-depth analysis in separate papers.

By drilling periodic thru-holes in a suspended film, the phonon system can be modified. Being motivated by the BCS theory, the technique, so-called phonon engineering, was applied to a niobium sheet. The newly emergent high-T_c superconductivity, however, cannot be accounted for by the BCS theory. Rather, its exposed configuration, namely a square-lattice oxygen network, is reminiscent of the copper--oxygen plane in cuprate high-T_c superconductors. It turns out that its magnetic result is consistent with the principle of giant atom, which was developed by another heroes of superconductivity, Fritz London and John Slater, in the 1930s, several decades earlier than the propagation of BCS theory. The superconducting transition feature is discussed on the basis of a comprehensive theory of the giant atom---the theory of hole superconductivity.

The stress imposed by ethanol to Saccharomyces cerevisiae cells are one of the most challenging limiting factors in industrial fuel-ethanol production. Consequently, the toxicity and tolerance to high ethanol concentrations has been the subject of extensive research, allowing the identification of several genes important for increasing the tolerance to this stress factor. However, most studies were performed with well characterized laboratory strains, and how the results obtained with these strains work in industrial strains remains unknown. In the present work we have tested three different strategies known to increase ethanol tolerance by laboratory strains in an industrial fuel-ethanol producing strain: overexpression of the TRP1 or MSN2 genes, or overexpression of a truncated version of the MSN2 gene. Our results show that the industrial CAT-1 strain tolerates up to 14% ethanol, and indeed the three strategies increased its tolerance to ethanol. When these strains were subjected to fermentations with high sugar content and cell-recycle, simulating the industrial conditions used in Brazilian distilleries, only the strain with overexpression of the truncated MSN2 gene showed improved fermentation performance, allowing the production of 16% ethanol from 33% of total reducing sugars present in sugarcane molasses. Our results highlight the importance of testing genetic modifications in industrial yeast strains under industrial conditions in order to improve the production of industrial fuel ethanol by S. cerevisiae.

The article is devoted to solving the problem of searching for universal explainable features that can remain explainable for a wide class of objects and phenomena and become an integral part of Explainable AI (XAI). The study is implemented on the example of an applied problem of early diagnostics of plant stress, using Thermal IR (TIR) and HSI, presented by 8 vegetation indices/channels. Each such index was presented by 5 statistical values. A Single-Layer-Perceptron classifier was used as the main instrument. TIR turned out to be the best of the indices in terms of efficiency in the field and sufficient to detect all 7 key days with 100% accuracy. Our study shows also that there are a number of indices, inluding NDVI, and usual color channels Red, Green, Blue, which are close to TIR possibilities in early plant stress detection with 100% accurasy or near, and can be used for wide class of plants and in different conditions their treatment. The stability of the stress classification in our study was maintained when the training set was reduced up to 10% of the dataset volume. The entropy-like feature of (max-min) for any indices/channels have determined as a leadersheep universal high-level explainable feature for the plant stress detection, which used in interaction with some of other statistical features.

This study was carried out to determine the effects of apple vinegar and sodium diacetate addition on the aerobic stability of fermented high moisture maize grain (HMM) silage after opening. In the study, the effect of three different levels (0, 0.5, 1.0%) of apple vinegar (AV) and sodium diacetate (SDA) supplementation to fermented HMM at two different storage conditions (27-29°C, 48% Humidity; 35-37°C, 26% Humidity) were investigated. The material of the study was fermented rolled maize grain with 62% moisture content stored for about 120 days. Silage samples were subjected to aerobic stability test with 3 replicates for each treatment group. Wendee and microbiological analyses were made at 0, 2, 4, 7, and 12 days. Meanwhile, samples were displayed in the T200 IR brand thermal camera. According to the thermogram results, 1% SDA addition positively affected HMM silages at the second and fourth days of aerobic stability at both storage conditions (p<0.05). Aerobic stability and infrared thermography analysis indicated that 1% AV, 0.5%, and 1% SDA additions to HMM silages had promising effects. Due to our results, we concluded that thermal camera images might be used as an alternative quality indicator for silages in laboratory conditions.

Immunoglobulin G (IgG) adopts a modular multidomain structure that mediates antigen recognition and effector functions, such as complement-dependent cytotoxicity. IgG molecules are self-assembled into a hexameric ring on antigen-containing membranes, recruiting the complement component, C1q. To provide deeper insights into the initial step of the complement pathway, we report a high-speed atomic force microscopy study for quantitative visualization of the interaction between IgG and the C1 complex composed of C1q, C1r, and C1s. Results showed that C1q in the C1 complex is restricted regarding internal motion and has a stronger binding affinity for on-membrane IgG assemblages than C1q alone, presumably because of smaller conformational entropy loss upon binding. Furthermore, we visualized a 1:1 stoichiometric interaction between C1/C1q and an IgG variant that lacks the entire CH1 domain in the absence of antigen. In addition to the canonical C1q-binding site on Fc, their interactions are mediated through a secondary site on the CL domain that is cryptic in the presence of the CH1 domain. Our findings offer clues for novel-modality therapeutic antibodies.

We describe a method for protein quantification and for mRNA quantification in small sample quantities of human induced pluripotent stem-cell-derived-cardiomyocytes (hiPSC-CMs). Demonstrated here is how the capillary-based protein detection system Wes^TM by ProteinSimple and the Power SYBR^TM Green Cells-to-CT^TM Kit by Invitrogen can be applied to individual samples in a 96-well microplate format and thus made compatible with high-throughput (HT) cardiomyocyte assays. As an example of the usage, we illustrate that Cx43 protein and GJA1 mRNA levels in hiPSC-CMs are enhanced when the optogenetic actuator, channelrodopsin-2 (ChR2), is genetically expressed in them. Instructions are presented for cell culture and lysate preparations from hiPSC-CMs, along with optimized parameter settings and experimental protocol steps. Strategies to optimize primary antibody concentrations as well as ways for signal normalization are discussed, i.e. antibody multiplexing and total protein assay. The sensitivity of both the Wes and Cells-to-CT kit enables protein and mRNA quantification in a HT format, which is important when dealing with precious small samples. In addition to being able to handle small cardiomyocyte samples, these streamlined and semi-automated processes enable quick mechanistic analysis.

Insulin receptors are internalized by endothelial cells; however, the impact of hyperinsulinemia on this process is not known. Thus, the aim of this study is to determine the role of hyperinsulinemia on insulin receptor function and internalization, as well as the potential impact of protein tyrosine phosphatase 1B (PTP1B). To this end, hippocampal microvessels were isolated from male C57Bl/6J mice on either a control or high-fat diet and assessed for insulin receptor signaling. Cell surface insulin receptors in brain microvascular endothelial cells were labelled with biotin to assess the role hyperinsulinemia plays on receptor internalization in response to stimulation, with and without Claramine treatment, a potent PTP1B antagonist. Our results indicated that insulin receptor levels increased in tandem with insulin receptor dysfunction in the high-fat diet mouse hippocampal microvessels. Hyperinsulinemic cell-receptors demonstrate a shift in splice variation towards decreased IR-A/IR-B ratios and demonstrate a higher membrane-localized proportion. This corresponded with decreased autophosphorylation at sites critical for receptor internalization and signaling, however, Claramine restored signaling and receptor internalization in hyperinsulinemic cells. In conclusion, hyperinsulinemia negatively impacts brain microvascular endothelial cell insulin receptor function and internalization, likely through both alternative splicing and increased negative feedback from PTP1B.

Three-dimensional reconstruction plays an important role in assisting doctors and surgeons in diagnosing bone defects’ healing progress. Common three-dimensional reconstruction methods include surface and volume rendering. As the focus is on the shape of the bone, volume rendering is omitted. Many improvements have been made on surface rendering methods like Marching Cubes and Marching Tetrahedra, but not many on working towards real-time or near real-time surface rendering for large medical images, and studying the effects of different parameter settings for the improvements. Hence, in this study, an attempt towards near real-time surface rendering for large medical images is made. Different parameter values are experimented on to study their effect on reconstruction accuracy, reconstruction and rendering time, and the number of vertices and faces. The proposed improvement involving three-dimensional data smoothing with convolution kernel Gaussian size 0.5 and mesh simplification reduction factor of 0.1, is the best parameter value combination for achieving a good balance between high reconstruction accuracy, low total execution time, and a low number of vertices and faces. It has successfully increased the reconstruction accuracy by 0.0235%, decreased the total execution time by 69.81%, and decreased the number of vertices and faces by 86.57% and 86.61% respectively.

This paper seeks to optimize the mechanical and durability properties of ultra-high performance concrete (UHPC). To meet this objective, concrete specimens were manufactured by using 1,100 kg/m3 of binder, water/binder ratio 0.20, silica sand and last generation of superplasticizer. Silica fume, metakaolin and two types of nano silica were used for improving the performances of the concrete. Additional mixtures included 13mm long OL steel fibers. Compressive strength, electrical resistivity, mercury intrusion porosimetry tests and differential and thermogravimetric thermal analysis were carried out. The binary combination of nano silica and metakaolin, and the ternary combination of nano silica with metakaolin and silica fume, led to the best performances of the UHPC, both mechanical and durable performances.

Rapid isolation of white blood cells (WBCs) from whole blood is an essential part of any WBC examination platform. However, most conventional cell separation techniques are labor-intensive and low throughput, require large volumes of samples, need extensive cell manipulation, and have low purity. To address these challenges, we report the design and fabrication of a passive, label-free microfluidic device with a unique U-shaped cross-section to separate WBCs from whole blood using hydrodynamic forces that exist in a microchannel with curvilinear geometry. It is shown that the spiral microchannel with a U-shaped cross-section concentrates larger blood cells (e.g., WBCs) in the inner cross-section of the microchannel by moving smaller blood cells (e.g., red blood cells (RBCs) and platelets) to the outer microchannel section and preventing them from returning to the inner microchannel section. Therefore, it overcomes the major limitation of a rectangular cross-section where secondary Dean vortices constantly enforce particles throughout the entire cross-section and decrease its isolation efficiency. Under optimal settings, more than 95% of WBCs can be isolated from whole blood under high-throughput (6 ml/min), high-purity (88%), and high-capacity (180 ml of sample in 1 hour) conditions. High efficiency, fast processing time, and non-invasive WBC isolation from large blood samples without centrifugation, RBC lysis, cell biomarkers, and chemical pre-treatments make this method an ideal choice for downstream cell study platforms.