A new frontier in solar thermal panel technology can be a high vacuum collector, thick enough to be equipped with solar concentrators based on non-imaging optics, such as the Compound Parabolic Concentrators (CPC). The high vacuum technology guarantees higher operating temperatures thanks to the enhanced thermal insulation, which leads to pay particular attention to the absorber radiative emission. In this paper by means of numerical simulations we compare the efficiency of a flat selective solar absorber under high vacuum to the efficiency of a CPC under high-vacuum collector.

The Pierre Auger Observatory is the world's largest operating detection system for the observation of ultra high energy cosmic rays (UHECRs). The detector allows detailed measurements of their energy spectrum, mass composition and arrival directions of primary cosmic rays in the energy range above $10^{17}$ eV. The data collected at the Observatory over the last decade show the suppression of the cosmic ray flux at energies above $4\times10^{19}$ eV. However, it is still unclear if this suppression is caused by the propagation of cosmic rays or rather by energy limitation of their sources. The other puzzle is the origin of UHECRs. Some clues can be drawn from studying the distribution of their arrival directions. The recently observed dipole anisotropy has an orientation which indicates an extragalactic origin of UHECRs. The Auger surface detector array is also sensitive to showers due to ultra high energy neutrinos of all flavours and photons, and recent neutrino and photon limits provided by the Observatory can constrain models of the cosmogenic neutrino production and exotic scenarios of the UHECRs origin, such as the decays of super heavy particles. In this paper the recent results on measurements of the energy spectrum, mass composition and arrival directions of cosmic rays, and future prospects are presented.

Copper-nitride (Cu3N) semiconductor material is attracting much attention as a potential, next-generation thin-film solar-light absorber in solar cells. In this communication, polycrystalline Cu3N thin films were prepared using reactive-RF-magnetron-sputtering deposition, at room temperature, onto glass and silicon substrates. The very-broadband optical properties of the Cu3N thin film layers were studied by UV-MIR (0.2-40 μm) ellipsometry and optical transmission, to be able to achieve the goal of a low-cost absorber material to replace the conventional silicon. The reactive-RF-sputtered Cu3N films were also investigated by focused ion beam scanning electron microscopy, and both FTIR and Raman spectroscopies.

Background: Chronic kidney disease, one of the most common diseases in the world, is characterized by irreversible impairment of the kidney’s metabolic, excretory, and endocrine functions. During end-stage renal disease, patients require renal replacement therapy, such as hemodialysis (HD). Protein-energy wasting is a common health problem among HD patients. However, this study aims to assess the nutritional status of HD patients at two HD centers in Jeddah, Saudi Arabia, and to determine its associated factors. Methods: A cross-sectional study was conducted at two different Dialysis Centers in Jeddah, Saudi Arabia; 211 female and male HD patients. Malnutrition was recognized using the Modified-SGA (M-SGA) comprising two parts: medical history and physical examination. Sociodemographic and health status for all patients were also determined. Patients were classified based on their M-SGA score into two groups: normal and malnourished. Results: Overall, 54.5% of the participants showed malnutrition. Unemployment, low muscle strength and mass, high level of medication use, and high dialysis vintage were positively (P<0.05) associated with malnutrition. Conclusion: The M-SGA score indicates a high prevalence of malnutrition among HD patients. These results show the importance of regular assessment and follow-ups for HD patients ensuring better health and nutritional status.

A comprehensive review of uncertainties in power systems, covering modeling, impact, and mitigation, is essential to understand and manage the challenges faced by the electric grid. Uncertainties in power systems can arise from various sources and can have significant implications for grid reliability, stability, and economic efficiency. Australia, susceptible to extreme weather such as wildfires and heavy rainfall, faces vulnerabilities in its power network assets. The decentralized distribution of population centers poses economic challenges in supplying power to remote areas, a crucial consideration for emerging technologies emphasized in this paper. In addition, the evolution of modern power grids, facilitated by deploying the advanced metering infrastructure (AMI), has also brought new challenges to the system due to the risk of cyber-attacks via communication link. However, the existing literature lacks a comprehensive review and analysis of uncertainties in modern power systems, encompassing uncertainties related to weather events, cyberattacks, and asset management, as well as the advantages and limitations of various mitigation approaches. To fill this void, this review covers a broad spectrum of uncertainties considering their impacts on the power system and explores conventional robust control, and modern probabilistic and data-driven approaches for modelling and correlating the uncertainty events to the state of the grid for optimal decision making. This article also investigates the development of robust and scenario-based operations, control technologies for microgrids (MGs) and energy storage systems (ESSs), and demand-side frequency control ancillary service (D-FCAS) and reserve provision for frequency regulation to ensure a design of uncertainty-tolerance power system. This review delves into the trade-offs linked with the implementation of mitigation strategies, such as reliability, computational speed, and economic efficiency. It also explores how these strategies may influence the planning and operation of future power grids.

Psychrophilic anaerobic digestion emerges as an appealing integrated solution for the management of agricultural waste, particularly for farmers in regions where the average temperature does not exceed 26°C, as seen in coffee cultivation. Therefore, this study seeks to assess the biomethane potential of thermochemical treated coffee husk through psychrophilic anaerobic digestion (C3-20°C-w/pretreatment). To examine its viability, outcomes were compared with reactors operating at both mesophilic (C1-35°C) and psychrophilic (C2-20°C) conditions, albeit without the use of pretreated coffee husk. The C3-20°C-w/pretreatment test demonstrated a 36.89% increase (150.47 mL CH4/g VS; 161.04 mL CH4/g COD), while the C1-35°C test exhibited a 24.03% increase (124.99 mL CH4/g VS; 133.77 mL CH4/g COD), both in comparison to the C2-20°C test (94.96 mL CH4/g VS; 101.63 mL CH4/g COD). Notably, the C3-20°C-w/pretreatment trial yielded superior outcomes, accompanied by an associated energy output of 4262.2 KWh/year, sufficient to meet the annual energy demands of 588 residences. This marks an increase of 100 and 217 residences compared to mesophilic and psychrophilic AD of CH without pretreatment, respectively.

The utilization of wind energy has become increasingly popular in the United States and many European countries due to its abundant natural source and optimized design. While existing wind turbines are predominantly large-scale and not suitable for standalone or distributed power production, Lubbock County in West Texas offers a diverse range of renewable energy options to meet its energy needs. The region relies heavily on utility-scale wind energy sources to supply power to the Texas Grid, replacing conventional fossil fuel-based systems. Currently, standalone solar PV systems are the preferred choice for renewable energy generation. However, West Texas possesses an ample supply of wind energy that can be harnessed to establish a microgrid and provide standalone power to rural communities. By employing the latest technology and optimizing efficiency, even in low-scale generation, a 6 kW permanent magnet alternator-based distributed wind turbine has been designed. This paper focuses on analyzing the techno-economic aspects of implementing this wind turbine in a real-world scenario, taking into account wind attributes such as velocity and available power at the specific location.

It is desirable to upgrade previous evolutionary theories, which have remained incomplete and controversial for decades. Here we employ the concept of carbon-based entities (CBEs), which include methane, amino acids, proteins, organisms, and other entities containing relatively many carbon atoms. We deduce the driving force, mechanisms, steps, modes, tempos of CBE evolution, through integration of biology, physics, and chemistry using logics for complex issues. We hence establish the Carbon-Based Evolutionary Theory (CBET). The CBET suggests that evolution is the increase in hierarchy, diversity, fitness of CBEs under natural selection and driven by thermodynamics due to the chemical effect of the thermodynamic features of the Earth on CBEs. It provides better explanations for life origin, macroevolution events, natural selection, sympatric speciation, and evolution tempos than previous evolutionary theories. It reveals the evolutionary basis of multiple important social notions, including diversity, collaboration, altruism, obeying rules, and proper increase in freedom. It refutes some wrong notions in thermodynamics, including negative entropy (negentropy) and that biological order is equal to thermodynamic order, which have misled many people. The CBET is supported by its deduction and application. It could be a rare bridge linking laws of thermodynamics, evolution of life, and development of human society, and could have great significance in various sciences.

The current paper aims to study the impact properties of additively manufactured Maraging steel (1.2709) using laser powder bed fusion (PBF-L) processing. The specimens were manufactured using 3Dsystems ProX 300 equipment under constant specific power input, or Andrew Number. The interactions between the build strategy and parameters, such as Hatch spacing and Scan speed was, and the impact strength and fracture were investigated. The Impact energy anisotropy was also investigated parallel and perpendicular to the build direction. Instrumented impact testing was performed, and the fractography supported that the fusion zone geometry dictated the fracture behaviour. The influence from gaseous elements such as Nitrogen, Oxygen and Hydrogen was found insignificant at the levels found in the printed material.

In the context of the coordinated development of digital economy and environmental protection, we take the strategy of "Broadband China" as a quasi-natural experiment, adopts the panel data of 284 cities from 2007 to 2020, and evaluates the policy effect of digital economy on total factor energy efficiency through the progressive DID model. The results show that: The construction of "Broadband China" demonstration city has significantly promoted the improvement of the total factor energy efficiency of the demonstration city, but there is also significant urban heterogeneity, which is manifested in the significant improvement of the total factor energy efficiency of the eastern city, the southern city, the big city and the non-resource-based city. It has no significant effect on the total factor energy efficiency of central and western cities, northern cities, small and medium-sized cities and resource-based cities. The construction of "Broadband China" demonstration cities can improve total factor energy efficiency by promoting technological progress and strengthening environmental regulations. Therefore, we should further strengthen the construction of digital infrastructure and give full play to its positive effects. Different cities should seek differentiated development paths based on their own resource endowments and development conditions, so that the digital economy can effectively improve the total factor energy efficiency.

Early prediction of thermal loads plays an essential role in analyzing energy-efficient buildings' energy performance. On the other hand, stochastic algorithms have recently shown high proficiency in dealing with this issue. These are the reasons that this work is dedicated to evaluating an innovative hybrid method for predicting the cooling load (CL) in buildings with residential usage. The proposed model is a combination of artificial neural networks and stochastic fractal search (SFS-ANN). Two benchmark algorithms, namely the grasshopper optimization algorithm (GOA) and firefly algorithm (FA), are also considered to be compared with the SFS. The non-linear effect of eight independent factors on the CL is analyzed using each model's optimal structure. Evaluation of the results outlined that all three metaheuristic algorithms (with more than 90 % correlation) can adequately optimize the ANN. In this regard, this tool's prediction error declined by nearly 23, 18, and 36 % by applying the GOA, FA, and SFS techniques. Also, all used accuracy criteria indicated the superiority of the SFS over the benchmark schemes. Therefore, it is inferred that utilizing the SFS along with ANN provides a reliable hybrid model for the early prediction of CL.

Wind power output is highly dependent on the wind speed at the selected site, therefore wind-speed distribution modeling is the most important step in the assessment of wind energy potential. This study aims at accurate evaluation of onshore wind energy potential in seven coastal cities in the south of Iran. Six Probability Distribution Functions (PDFs) were examined over representative stations. It has been deduced that the Weibull function, which was the most used PDF in similar studies, was only applicable to one station. Here, Gamma offered the best fit for three stations and for the other ones, Generalized Extreme Value (GEV) performed better. Considering the ranking of six examined PDFs and the simplicity of Gamma, it was identified as the effective function in the southern coasts of Iran bearing in mind the geographic distribution of stations. Besides, six turbine power curve functions were contributed to investigate the capacity factor. That was very important, as using only one function could cause under- or over-estimation. Then, stations were classified based on the National Renewable Energy Laboratory system. Last but not least, examining a range of wind turbines enabled scholars to extend this study into the practice and prioritize development of stations considering budget limits.

To compare the quality of low-energy VMIs obtained with three DECT platforms according to phantom diameter. Three sections of the Mercury Phantom 4.0 were scanned on two generations of split-filter CTs (SFCT-1st and SFCT-2nd) and on one Dual-source CT (DSCT). Noise power spectrum (NPS), task-based transfer function (TTF) and detectability index (d’) were assessed on VMIs from 40 to 70keV. Highest noise magnitude values were found with SFCT-1st and noise magnitude was higher with DSCT than with SFCT-2nd for 26-cm (10.2±1.3%) and 31-cm (7.0±2.5%), and the opposite for 36-cm (-4.2±2.5%). The highest average NPS spatial frequencies and TTF values at 50% (f50) values were found with DSCT. For all energy levels, f50 values were higher with SFCT-2nd than SFCT-1st for 26-cm (3.2±0.4%) and the opposite for 31-cm (-6.9±0.5%) and 36-cm (-5.6±0.7%). The lowest d’ values were found with SFCT-1st. For all energy levels, d’ values were lower with SFCT-2nd than with DSCT for 26-cm (-6.2±0.7%), similar for 31-cm (-0.3±1.9%) and higher for 36-cm (5.4±2.7%). In conclusion, compared to SFCT-1st, SFCT-2nd exhibited lower noise magnitude and higher detectability values. Compared with DSCT, SFCT-2nd had lower noise magnitude and higher detectability for the 26-cm but the opposite was true for the 36-cm.

Indirect calorimetry (IC) is a widely used method to study animal energy metabolism by measuring gas exchange. The accuracy of IC depends on detecting variations in signals reflecting the metabolic response, which can be challenging due to measurement noise and external factors. In this study, we propose a methodology to validate IC systems, including an easy-to-use spreadsheet for data computing, to verify accuracy and detect whole-system leaks. We conducted a re-covery test using a simulation of CO2 dynamics in MS Excel and injecting a known CO2 concentration into four respirometry chambers. The clearance rate of CO2 was observed and compared to the expected clearance rate from the simulation. The results from the recovery test in our system show that the proposed methodology is accurate and precise. The proposed methodology and recovery test can be used to standardize the validation of IC systems, providing accurate measurements of animal energy metabolism in different environmental conditions and energy utilization from feeds.

In this study, a new structure is proposed based on the body-centered cubic (BCC) lattice structure: adding a cubic truss in the center of the BCC structure, which is denoted by TLC (Truss-lattice-cube). The different dimensions of the central cube can affect the mechanical properties of the lattice structure notably. With a fixed length (15mm) of a unit cell, the optimal size for the central cube is determined to be 5 mm. Quasi-static compressive tests are performed on specimens made of Polylactic Acid (PLA) using additive manufacturing technology. The deformation characteristics of the new structure is analyzed in detail by experiments and numerical simulations. Compared to the BCC structure, the mechanical properties of the TLC structure are significantly improved. The initial flow stress of the TLC has been increased by 122% at a strain of 0.1; the specific strength has been enhanced by 293% at a strain of 0.5; and the specific energy absorption has been improved by 312% at the strain of 0.6. Printing defects in the lattice structure could deteriorate the mechanical property remarkably. In this work, incorporation of microcracks into the finite element model makes the simulation capture the influence of printing defects and improve the predictive accuracy of simulation significantly.

The paper describes and analyzes the performance of a new thermoelectric generation system based on the use of Peltier cells inserted in the ducts of the air conditioning equipment. The hot and cold air streams that flow in the two separated sections of an air conditioning system are used to create a thermal gradient between the two faces of the Peltier cells. Hot and cold air flow inside the A/C unit are driven to a built in thermal chamber where the Peltier cells are placed. Peltier cells are incrusted into an insulation wall that separates the two sections of the chamber through which hot and cold air streams are flowing. The so designed configuration allows the Peltier cells to generate electric current. The study has been run for constant cold air temperature and variable hot air temperature, resulting in a variable performance of the thermoelectric generator. Theoretical study has been completed with experimental tests to determine real performance of the thermoelectric unit. Efficiency of the thermoelectric generator has been found to be linearly dependent on the temperature difference between hot and cold air subsections of the chamber. Maximum efficiency, however, is limited by the hot air stream temperature, since in real conditions ambient temperature cannot overpasses a specific value. For standard operational conditions, 5º C and 45º C for the cold and hot air streams, the thermoelectric generator operates at 44% of the maximum efficiency attainable.

As part of the Earth Climate Observatory space mission concept for the direct observation from space of the Earth Energy Imbalance, we propose an advanced camera suite for the high resolution observation of the Total Outgoing Radiation of the Earth. For the observation of the Reflected Solar Radiation, we propose the use of two multispectral cameras covering the range from 400 to 950 nm, with a nadir resolution of 1.7 km, combined with a high resolution RGB camera, with a nadir resolution of 0.57 km. For the observation of the Outgoing Longwave Radiation, we propose the use of 6 microbolometer cameras, with each a spectral bandwidth of 1 μm in the range from 8 to 14 μm, and with a nadir resolution of 2.2 km.

The most important step for the installation of a wind farm is to know the wind regime in the region, since an error in estimating this wind speed causes an error proportional to the cube of power, resulting in financial losses for investors. Therefore, knowing the methods used for predicting wind speed becomes important and the knowledge of how research and studies in this area are going helps map the subject and outline strategies for developing research in strategic areas. For this purpose, the Scopus database was used considering some keywords, such as ("forecast" OR "prevision") AND "wind" AND ("turbine" OR "power" OR "energy" or "velocity" or "speed"), considering the period since 2019, and analyzing the data of the documents found using the Bibliometrix package. With the results found, it was possible to map researchers, institutions that are developing work in this area, in addition to the most cited articles, among other aspects analyzed.

The Unmanned Aerial Vehicles (UAVs), used in civilian applications such as emergency medical deliveries, precision agriculture, wireless communication provisioning, etc., face the challenge of limited flight time due to their reliance on the on-board battery. Therefore, developing efficient mechanisms for in-situ power transfer to recharge UAV batteries hold potential in extending their mission time. In this paper, we study the use of far-field wireless power transfer (WPT) technique from specialized, transmitter UAVs (tUAVs) carrying Multiple Input Multiple Output (MIMO) antennas for transferring wireless power to receiver UAVs (rUAVs) in a mission. The tUAVs can fly and adjust their distance to the rUAVs to maximize energy transfer. The use of MIMO antennas further boost the energy reception by narrowing the energy beam toward the rUAVs. The complexity of their dynamic operating environment increases with the growing number of tUAVs, and rUAVs with varying levels of energy consumption and residual power. We propose an intelligent trajectory selection algorithm for the tUAVs based on a deep reinforcement learning model called Proximal Policy Optimization (PPO) to optimize the energy transfer gain. Simulation results demonstrate that with the use of PPO, the system achieves a tenfold flight time extension compared to no wireless recharging. Further, PPO outperforms the benchmark movement strategies of ’Traveling Salesman Problem’ and ’Low Battery First’ when used by the tUAVs.

It is proposed that both human creativity and human consciousness are (unintended) consequences of the human brain’s extraordinary energy efficiency. The topics of creativity and consciousness are treated separately, though have a common sub-structure. It is argued that creativity arises from a synergy between two cognitive modes of the human brain (which broadly coincide with Kahneman’s Systems 1 and 2). In the first, available energy is spread across a relatively large network of neurons. As such, the amount of energy per active neuron is so small that the operation of such neurons is susceptible to thermal (ultimately quantum decoherent) noise. In the second, available energy is focussed on a small enough subset of neurons to guarantee a deterministic operation. An illustration of how this synergy can lead to creativity with implications for computing in silicon are discussed. Starting with a discussion of the concept of free will, the notion of consciousness is defined in terms of an awareness of what are perceived to be nearby counterfactual worlds in state space. It is argued that such awareness arises from an interplay between our memories on the one hand, and quantum physical mechanisms (where, unlike in classical physics, nearby counterfactual worlds play an indispensable dynamical role) in the ion channels of neural networks. As with the brain’s susceptibility to noise, it is argued that in situations where quantum physics plays a role in the brain, it does so for reasons of energy efficiency. As an illustration of this definition of consciousness, a novel proposal is outlined as to why quantum entanglement appears so counter-intuitive.

Global financial investments in energy production and consumption are significant since all aspects of a country's economic activity, and development require energy resources. In this paper, we assess the investment trends in the global energy sector during, before and after financial crises of 2008 using two data sources: (1) Dealogic database providing cross‐border mergers and acquisitions (M&As), and (2) fDi Intelligence fDi Markets database providing greenfield (GF) foreign direct investments (FDIs). We highlight the changing role of China and compare its M&A and GF FDI activities to those of the United States, Germany, UK, Japan and others during this period. We analyze the investments along each segment of the energy supply chain of these countries to highlight the geographical origin and destination, sectoral distribution, and cross‐border M&As and GF FDI activities. Our paper shows that while energy accounts for nearly 25% of all GF FDI, it only accounts for 4.82% of total M&A FDI activity in the period 1996-2016. China's outbound FDI in the energy sector started its ascent around the time of the global recession and had accelerated in the post-recession phase. In the energy sector, the development of China's outbound cross‐border M&As is similar to USA or UK, located mostly in the developed countries in the west, while their outbound GF investments are spread across many countries around the world. Also, China's outbound energy M&As are concentrated in certain segments (extraction, and electricity generation) while their GF covers all segments of the energy supply chain.

Production of energy is a main task of cancer cells metabolism, since costs of duplicating are enormous. Although energy is derived in cells by dismantling carbon to carbon bonds of any macronutrient, cancer nutritional needs for energetic purposes have been studied primarily as dependent on glycolysis. Since the end of the last century, awareness of dependence of cancer metabolism on amino acids not only for protein syntheses but also for matching energy needs has grown. The roles of specific amino acids, like glutamine, glycine and serine have been explored in different experimental conditions and reviewed. Moreover, there are epidemiological evidences that some amino acids used as supplement for therapeutic reasons (the branched chain ones) may reduce incidence of liver cancer, and some molecular mechanism has been proposed as functional to their protective action. On the contrary, metabolic signature of some pathology connected with increased risk of cancer, like prolonged hyperinsulinemia in insulin resistant patients, is signed by plasma elevated levels of the same branched chain amino acids, posing puzzling questions to clinicians. Most recently, peculiar formulations of amino acids, deeply different if compared to amino acids compositions normally present in foods, have shown the power to master epigenetics slowing growth or driving cancer cells to apoptotic death, while being even beneficial for normal cells and for animals health and life span. In this review, we will analyze and try to disentangle some of the many knots dealing with complexities of amino acids biology and linked to cancer metabolism.

In this study we investigate the formation of dynamical energy cascades in higher order KdV-type equations. In the beginning we recall what is known about the dynamic cascades for the classical KdV (quadratic) and mKdV (cubic) equations. Then, we investigate further the mKdV case by considering a richer set of initial perturbations in order to check the validity and persistence of various facts previously established for the narrow-banded perturbations. Afterwards we focus on higher order nonlinearities (quartic and quintic) which are found to be quite different in many respects from the mKdV equation. Throughout this study we consider both the direct and double energy cascades. It was found that the dynamic cascade is always formed, but its formation is not necessarily accompanied by the nonlinear stage of the modulational instability. Direct cascade structure remains invariant regardless the size of the spectral domain. In contrast, the double cascade shape can depend on the size of the spectral domain, even if the total number of cascading modes remains invariant. Results obtained in this study can be potentially applied to plasmas, free surface and internal wave hydrodynamics.

In this study, we investigate the formation of dynamical energy cascades in higher-order KdV-type equations. In the beginning, we recall what is known about the dynamic cascades for the classical KdV (quadratic) and mKdV (cubic) equations. Then, we investigate further the mKdV case by considering a richer set of initial perturbations in order to check the validity and persistence of various facts previously established for the narrow-banded perturbations. Afterwards, we focus on higher-order nonlinearities (quartic and quintic) which are found to be quite different in many respects from the mKdV equation. Throughout this study, we consider both the direct and double energy cascades. It was found that the dynamic cascade is always formed, but its formation is not necessarily accompanied by the nonlinear stage of the modulational instability. Direct cascade structure remains invariant regardless of the size of the spectral domain. In contrast, the double cascade shape can depend on the size of the spectral domain, even if the total number of cascading modes remains invariant. Results obtained in this study can be potentially applied to plasmas, free surface and internal wave hydrodynamics.

Urbanization and industrialization processes in Mongolia have been significant and rapid for the last half-century. During this period, changes in political and economic systems, growth in the population, and the occasional harsh climate conditions were subject to fluctuations in the natural resource usage. The total Ecological Footprint (EF) in Mongolia has increased from 6.8 million global hectares (gha) in 1961 to 14.6 million gha in 2012. However, Biocapacity (BC) has decreased from 50.6 million gha in 1961 to 39.0 million gha in 2012. The study shows that grazing land Footprint and carbon uptake land Footprint are the two major contributors of the recent intensified use of biological resources. To ensure stable economic development and sustainable use of natural resources, environmental planning is required to consider both the population’s pressure on the environment and the ecosystem’s regeneration capacity, simultaneously. We have proposed a few possible strategies for sustainable utilization of grazing land Footprint and carbon Footprint. For grazing land Footprint, efficient management of both herding practice and number of animals should be considered. In case of carbon Footprint, it is estimated that with the improved combustion efficiencies of coal-based power plants and the maximum use of renewable energy, carbon dioxide (CO₂) emissions in Mongolia can be reduced up to 30% compared to the base line business as usual case in 2030.

The aim of this work was to determine the potential of using a pulsed electric field (PEF) and ultra-sound (US) apparatus to produce mitragynine extracts from Mitragyna speciosa dried leaves. Four modes of the device were tested: PEF, US, US + PEF, and PEF + US. The results were compared with extracts obtained using a conventional technique (maceration, as the control). Changes in the mitragynine content were determined with the liquid chromatography/mass spectrometry (LC-MS/MS) method. The LC-MS/MS analysis showed that the mitragynine contents from kratom extracts using four different modes were different. The highest extraction (106.63 ± 0.85 mg/L) of mitragynine was achieved by the PEF + US procedure, followed by US + PEF (97.27 ± 1.33 mg/L), with increased extraction efficiencies of 45.81 ± 0.59% and 33.00 ± 1.85%, respectively. Moreover, the total energy consumption under the combination technique was 25.0% lower than that with PEF assistance. Furthermore, scanning electron microscopy (SEM) and Fourier Transform Infrared Spectroscopy (FTIR) provided confirmatory evidence for the extraction of M. speciosa by the prototype. This study confirmed that PEF and US devices can be considered a green alternative method and may contribute to the application of agricultural products.

Peer-to-peer (P2P) energy trading – where energy prosumers transact directly between each other – could help enable transition to a low-carbon energy system. If it is to be supported in policy and regulation, it is important to anticipate the distributional impacts (or how it might impact segments of society differently). However, real-world evidence on P2P energy trading is currently extremely limited. To address this challenge in the short- to medium-term, this study aimed to explore what might be learned from the extensive body of research on a comparable offering in the accommodation sector: Airbnb. A realist review approach was employed to maximise transferability of findings, focused on what mechanisms are thought to lead to what distributional outcomes, in what contexts. On the basis of the review, participation in (and receipt of benefits of) P2P energy trading schemes would be expected to represent disproportionately those living in areas with network management challenges, who are younger and more highly educated. The review also raised the prospect of discrimination on the basis of characteristics such as race and gender where there are high levels of individual choice over who to trade with. Recommendations include monitoring, incentivising diversity, anonymization, and limiting trading choices.

Polyhedral Oligomeric Silsesquioxanes (POSS) are one of the smallest silica nano particles. The presence of ordered ladder-like or cage conformation in their structure leads to remarkable thermal stability far greater than that for a linear polysiloxane. Reinforcement with nano particles is one of the recently favored strategy used to enhance the performance of polymers materials. The cyclic silica structure present in POSS ensures excellent thermal and mechanical stability. As a reinforcing filler, POSS can enhance the resistance of polymer matrix against pyrolysis and corrosion. In this paper, amine-terminated POSS with ladder like structure was synthesized by condensation of hydrolyzed aminosilane coupling agent. The ladder-like structure of POSS severely limits the motion of the chain backbone. The absence of phase transition for the synthesized POSS was confirmed by differential scanning calorimetry (DSC). Thermogravimetric analysis (TGA) was utilized to evaluate the thermal stability of POSS. TGA data show that the ladder-like POSS reported here has high char yield of about 75 % in nitrogen atmosphere and 54% in air atmosphere at 800℃. The TGA derivative curves show that the degradation of ladder-like POSS involves multiple stages and that the degradation rate is directly proportional to the heating rate. With the aid of Fourier Transform Infrared Spectroscopy (FT-IR), the cyclic structure of Si-O-Si bonding was determined to be the predominant structure. By analyzing the FTIR spectra of the cured POSS residue obtained at the specified temperatures, the detailed degradation mechanism of POSS was inferred. From the FTIR spectra of the low temperature cured samples, it was shown that the terminal silanol group was eliminated below 400℃. Some intermediate polymeric siloxane structures were observed by means of FT-IR and they eventually transitioned into silica which is the final product of pyrolysis of POSS. The presence of the FTIR transmission peaks at 1000 and 1100 cm-1, due to asymmetrical vertical and horizontal stretching of Si-O-Si, were the key evidence for the inferred ladder-like structure of POSS.

In the context of the Bridge Electromagnetic Theory, a quantum-relativistic theory based on Maxwellian electromagnetism, it has recently been shown that the characteristics of a hydrogen atom can be obtained through an electron-proton orbital capture process forming a non-radial emitting dipolar electromagnetic source. The model structurally different to the Bohr-Sommerfeld and Schrödinger models has now been deepened and completed by testing it on the properties of hydrogen and deuterium atoms and of helium and lithium in hydrogenoid form. These last two atoms are of cosmological interest as they are the heaviest elements produced by electron capture in the early universe. The theoretical results obtained regarding the atomic structure and spectra are in excellent agreement with the observational data by suggesting the implicit correctness of the model. It is also highlighted that the electron-nucleus interaction is influenced on an isotopic basis as a function of the value of the inertial mass of the nuclei considered.

Though inland ships share a small portion of the total global CO₂ emission from shipping, from the individual country’s economic and environmental perspective, this is very important. In order to reduce CO₂ emission from the sea going ships by increasing energy efficiency, International Maritime Organization (IMO) adopted a generalized Energy Efficiency Design Index (EEDI) in 2011. However, due to the variation in the environmental, geographic and economic conditions, a generalized EEDI cannot be established in a similar fashion as established by IMO. Shallow and restricted water effects, different fuel qualities (to reduce operational cost), increase in engine power requirement, reduction in carrying capacity, cargo availability, etc. forbid the use of existing EEDI formulation for inland waterways. So, an EEDI formulation based on revised parameters has been proposed for the inland ships of Bangladesh. This paper focuses on the implementation of the revised EEDI formulation by performing a sensitivity analysis of different ship design parameters. Based on the analysis, suggestions were made on how to design inland oil tankers of Bangladesh using the revised EEDI formulation for reducing CO₂ from the current level. Keeping the same speed and capacity, those vessels were redesigned based on those suggestions. The CFD analysis of those redesigned vessels using ‘Shipflow’ has shown a total resistance reduction of 10-13%.

The calculation of the vapour pressure of organic molecules at 298.15K is presented using a commonly applicable computer algorithm based on the group-additivity method. The basic principle of this method rests on the complete breakdown of the molecules into their constituting atoms, further characterized by their immediate neighbour atoms. The group contributions are calculated by means of a fast Gauss-Seidel fitting algorithm using the experimental data of 2036 molecules from literature. A ten-fold cross-validation procedure has been carried out to test the applicability of this method, which confirmed excellent quality for the prediction of the vapour pressure, expressed in log(pa), with a cross-validated correlation coefficient Q2 of 0.9938 and a standard deviation  of 0.26. Based on these data, the molecules' standard Gibbs free energy G°vap has been calculated. Furthermore, using their enthalpies of vaporization, predicted by an analogous group-additivity approach published earlier, the standard entropy of vaporization S°vap has been determined and compared with experimental data of 1129 molecules, exhibiting excellent conformance with a correlation coefficient R2 of 0.9598, a standard error  of 8.14 J/mol/K and a medium absolute deviation of 4.68%.

India, the world’s most populous country, is the world's third-largest emitter of greenhouse gases (GHGs). Despite employing several energy sources, it still relies heavily on coal, its primary energy source. Given India’s swiftly rising energy demand, this challenges meeting emission reduction targets. India has significantly increased investments in renewables like solar and hydrogen in recent years. While commendable, these initiatives alone cannot meet the country's expanding energy demands. In the short term, India must rely on both domestic and imported fossil fuels, with natural gas being the most environmentally friendly option. In this context, this paper attempts to forecast energy consumption, natural gas production, and consumption in India till 2050 using both univariate and multivariate forecasting methods. For multivariate forecasting, we have assumed two alternative possibilities for GDP growth: the business-as-usual and the high-growth scenarios. Each of our forecasts indicates a notable shortfall in the projected production of natural gas compared to the expected demand, implying our results are robust. Our model predicts that nearly 30-50 percent of India’s natural gas consumption will be met by imports, mainly in the form of LNG. Based on these findings, this paper recommends that Indian government policies emphasize increasing domestic natural gas production, importing LNG, and expanding renewable energy resources.

Recent years have seen a rapid uptake in distributed energy resources (DER). Such technologies pose a number of challenges to network operators, which can ultimately limit the amount of rooftop solar photovoltaics (PV) systems that can be connected to a network. The objective of this industry-based research was to determine the potential network effects of forecast levels of customer owned rooftop solar PV on Energy Queensland’s distribution network and formulate functions that can be used to determine such effects without the requirement for detailed network modeling and analysis. In this research, many of Energy Queensland’s distribution feeders were modelled using DIgSILENT PowerFactory and analyzed with forecast levels of solar PV and customer load. Python scripts were used to automate this process and quasi dynamic simulation (QDSL) models were used to represent the dynamic volt-watt and volt-var response of inverters, as mandated by the Australian Standard AS/NZS 4777. In analyzing the results, linear regression was used to form trend equations that represent various network characteristics against the number of PV connections. The trend equations provide a way of approximating network characteristics for other feeders under various levels of customer owned rooftop solar PV without the need for detail modeling.

DC residential distribution system (RDS) consisted by DC living home will be a significant integral part in the future green transmission. Meanwhile, the increasing number of distributed resources and intelligent devices will change the power flow between main grid and demand sides. The utilization of distributed generations (DGs) requires an economic operation, stability, environmentally friendly in the whole DC system. This paper not only presents an optimization schedule and transactive energy (TE) approach through centralized energy management system (CEMS), but a control approach to implement and ensure DG output voltages to various DC buses in DC RDS. Based on data collection, prediction and a certain objection, the expert system in CEMS can work out the optimization schedule, after this, the voltage droop control for steady voltage is aligned with the command of unit power schedule. In this work, a DC RDS is as a case study to demonstrate the process, the RDS is associated with unit economic models, cost minimization objective is proposed to achieve based on real-time electrical price. The results show that the proposed framework and methods will help the targeted DC residential system to reduce the total cost and reach stability and efficiency.

To improve the accuracy of short-term multi-energy load prediction models for integrated energy systems, the historical development law of the multi-energy loads must be considered. Moreover, understanding the complex coupling correlation of the different loads in the multi-energy systems and accounting for other load-influencing factors, such as weather, may further improve the forecasting performance of such models. In this study, a two-stage fuzzy optimization method is proposed for the feature selection and identification of the multi-energy loads. To enrich the information content of the prediction input feature, we introduced a copula correlation feature analysis in the proposed framework, which extracts the complex dynamic coupling correlation of multi-energy loads and applies Akaike information criterion (AIC) to evaluate the adaptability of the different copula models presented. Furthermore, we combined a NARX neural network with Bayesian optimization and an extreme learning machine model optimized using a genetic algorithm to effectively improve the feature fusion performances of the proposed multi-energy load prediction model. The effectiveness of the proposed short-term prediction model was confirmed by the experimental results obtained using the multi-energy load time-series data of an actual integrated energy system.

The battle of currents between AC and DC reignited as a result of the development in the field of power electronics. The efficiency of DC distribution systems is highly dependent on the efficiency of distribution converter, which calls for optimized schemes for efficiency enhancement of distribution converters. Modular solid-state transformers play a vital role in DC Distribution Networks and Renewable Energy systems (RES).This paper deals with efficiency-based load distribution for Solid State Transformers (SSTs) in DC distribution networks. Aim is to achieve a set of minimum inputs that are consistent with output while considering constraints and efficiency. As the main feature of modularity is associated with a three-stage structure of SSTs. This modular structure has been optimized using Ant Lion Optimizer (ALO) and validated by applying it EIA (Energy Information Agency) DC Distribution Network which contains SSTs. In the DC distribution grid, modular SSTs provide promising conversion of DC power from medium voltage to lower DC range (400V). The proposed algorithm is simulated in MATLAB and also compared with two other metaheuristic algorithms. The obtained results prove that the proposed method can significantly reduce input requirements for producing the same output while satisfying the specified constraints.

Plastic waste constitutes one of the most important sources of pollution worldwide. Despite the growing recycling trend, nowadays there are no effective technologies that can compensate for the continuous increase in plastic production. Polyesters and polyamides are one of the most produced single-use plastics, mainly used in manufacturing textiles and soft drinks bottles. Today, only a very low fraction of these polymers can be recycled. It can be done by exploiting two leading technologies: mechanical and chemical recycling. Mechanical recycling represents, nowadays, the most used industrial application. However, it can treat a very narrow range of waste materials due to the impossibility of removing dyes and the deterioration of mechanical properties due to the incompatibility of different plastic materials. Another critical limit of this recycling technology is the limited number of recycling loops that can be done due to the thermal degradation that occurs during the extrusion process. The second possibility is chemical recycling, which allows the depolymerization of the original product to recover the monomers directly. The main drawbacks are the long reaction times and the many solvents needed to achieve high-purity products. Therefore, chemical recycling is economically feasible, only for big companies that can produce the virgin polymer in situ. In this work, a new technology has been patented. This process is constituted of three main steps. The first one is the distillation-assisted cyclodepolymerization (DA-CDP), introduced as a modification of the CDP process. In this unit, cyclic oligomers together with high molecular weight compounds have been produced. Then, after polymer purification, it is possible to achieve the same molecular weight of the initial polymer in less than 30 minutes, exploiting the ring-opening polymerization (ROP) in the next step.

An interesting physical phenomenon was recently observed when a fresh-water basin is covered by a thin ice film that has properties similar to that of a rubber membrane. Surface waves can be generated under the action of wind on the air-water interface that contains an ice film. The modulation property of hydro-elastic waves (HEWs) in deep water covered by thin ice film blown by the wind with a uniform vertical profile is studied here in terms of the air-flow velocity versus a wavenumber. The modulation instability of HEWs is studied through the analysis of coefficients of the nonlinear Schrödinger (NLS) equation with the help of the Lighthill criterion. The NLS equation is derived using the multiple scale method in the presence of airflow. It is demonstrated that the potentially unstable hydro-elastic waves with negative energy appear for relatively small wind speeds, whereas the Kelvin–Helmholtz instability arises when the wind speed becomes fairly strong. Estimates of parameters of modulated waves for the typical conditions are given.

This letter aims to show the connection between the sinc approximation for high-energy absorption cross section and the shadow radius of the spherically symmetric black hole. This connection can give a physical interpretation of the absorption cross section in the eikonal limit parameters. Moreover, the use of this alternative way, one can extract its shadow radius from the absorption cross section in high energy limits to gain more information about the black hole spacetime. Our results indicate that the increasing the value of the shadow radius of the black hole, exponentially increase the the absorption cross section of the black hole in high-energy limits which can be captured by the Event Horizon Telescope (EHT) collaboration.

Establishing an accurate mathematical model is the foundation of simulating the motion of marine vehicles and structures, and it is the basis of modeling-based control design. System identification from observed input-output data is a practical and powerful method. However, for modeling objects with different characteristics and known information, a single modeling framework can hardly meet the requirements of model establishment. Moreover, there are some challenges in system identification, such as parameter drift and overfitting. In this work, three robust methods are proposed for generating ocean hydrodynamic models based on Bayesian regression. Two Bayesian techniques, semi-conjugate linear regression and noisy input Gaussian process regression, are used for parametric and nonparametric gray-box modeling and black-box modeling. The experimental free-running tests of the KVLCC2 ship model and a multi-freedom wave energy converter (WEC) are used to validate the proposed Bayesian models. The results demonstrate that the proposed schemes for system identification of the ship and WEC have good generalization ability and robustness. Finally, the developed modeling methods are evaluated considering the aspects required conditions, operating characteristics and prediction accuracy.

The world is progressing towards a more advanced society where end-consumers have access to local renewable-based generation and advanced forms of information and technology. Hence, it is in a current state of transition between the traditional approach to power generation and distribution, where end-consumers of electricity have typically been inactive in their involvement with energy markets and a new approach that integrates their active participation. This new approach includes the use of distributed energy resources (DER) such as renewable-based generations and demand response (DR), which are being rapidly adopted by end-consumers, where incentives are strong. This paper presents the role of DR aggregator to effectively integrate DER technologies as a new source of energy capacity, into the electricity networks using information communication technology and industry knowledge. This framework based on DR aggregators will facilitate renewable energy integration and customer engagement in electricity market efficiently. To this aim, advantages and disadvantages of DR aggregators are discussed in this paper from political, economic, social and technological (PEST) point of views. Based on this analysis, a strengths, weaknesses, opportunities, and threats (SWOT) analysis for a typical DR aggregator is presented.

This paper investigates the effects of various process parameters, specifically the substrate temperature, on weld track geometry in Directed Energy Deposition (DED) processes. A specialized experimental setup integrated within a DED machine facilitates controlled thermal conditioning of sample sheets. Through Design of Experiments (DoE) methods, individual weld marks are generated and analysed to assess geometric characteristics. Regression models are constructed to predict machine parameters for desired weld geometry at different substrate temperatures. Validation experiments confirm the accuracy and reliability of the regression models. Results show a consistent trend towards target geometric features across a broad range of substrate temperatures. Despite deviations in measured values, successful fabrication is achieved, demonstrating robust bonding between weld and substrate. Contact angle predictions exhibit precision within a partial temperature range for proper deposition. The developed model offers insights for optimizing DED process parameters to achieve desired weld characteristics, advancing the capabilities and reliability of additive manufacturing technology. Future work aims to refine the regression model and explore additional mathematical relationships for enhanced accuracy. An implication of this work is the potential to vary the local mechanical properties of parts by controlling the temperature profile while maintaining consistent geometric characteristics. By manipulating the substrate temperature, it may be possible to tailor the microstructure and mechanical properties of fabricated components in the future to meet specific requirements in different regions of the part.

This study advances the field of solar irradiance nowcasting by introducing a discrete-level classification approach, diverging from traditional continuous measurement methods. Grounded in a need for cost-effective and modular solutions, the research employs high-resolution computer vision coupled with a deep learning framework to predict Direct Normal Irradiance (DNI). By harnessing the capabilities of a Logitech C900 1080p HD camera and an NVIDIA Jetson module, the study achieves real-time data processing, pivotal for CSP systems' operational efficiency. The core of the methodology is the ResNet-50 convolutional neural network, refined via transfer learning on a bespoke dataset, culminating in a predictive accuracy of 85.78%. This discrete classification model contrasts with conventional, costly instruments like the MS-57, offering a novel and accessible alternative for DNI estimation. Such innovation not only demonstrates high predictive accuracy but also signifies a shift towards less resource-intensive and more adaptable solar energy forecasting tools, contributing a significant leap towards optimizing renewable energy systems.

To minimise environmental impact, avoid regulatory penalties, and improve competitiveness, energy-intensive manufacturing firms require accurate forecasts of their energy consumption so that precautionary and mitigation measures can be taken. Deep learning is widely touted as a superior analytical technique to traditional artificial neural networks, machine learning, and other classical time series models due to its high dimensionality and problem solving capabilities. Despite this, research on its application in demand-side energy forecasting is limited. We compare two benchmarks (Autoregressive Integrated Moving Average (ARIMA), and an existing manual technique used at the case site) against three deep learning models (simple Recurrent Neural Networks (RNN), Long Short-Term Memory (LSTM), and Gated Recurrent Unit (GRU)) and three machine learning models (Support Vector Regression (SVM), Random Forest, and K-Nearest Neighbors (KNN)) for short term load forecasting (STLF) using data from a Brazilian thermoplastic resin manufacturing plant. We use the grid search method to identify the best configurations for each model, and then use Diebold-Mariano testing to confirm the results. Results suggests that the legacy approach used at the case site is the worst performing, and that the GRU model outperformed all other models tested.

The global photovoltaic (PV) installed capacity, vital for the electric sector decarbonation, has reached 1,552.3 GWp in 2023. In France, the capacity stood in April 2024 at 19.9 GWp. The growth of the PV installed capacity over a year was nearly 32% worldwide and 15.7% in France. However, integrating PV electricity into grids is hindered by poor knowledge of rooftop PV systems, constituting 20% of France's installed capacity, and the lack of measurements of the production stemming from these systems. This problem of lack of measurements of the rooftop PV power production is referred to as the lack of observability. Using ground truth measurements of individual PV systems, available at an unprecedented temporal and spatial scale, we show that estimating the PV power production of an individual rooftop system by combining solar irradiance and temperature data, the characteristics of the PV system inferred from remote sensing methods and an irradiation-to-electric power conversion model provides accurate estimations of the PV power production. Our study shows that we can improve rooftop PV observability, and thus its integration into the electric grid, using little information on these systems, a simple model of the PV system and weather data.

Static voltage stability has become one of the significant risks faced by large-scale renewable energy integration. However, traditional methods for static voltage stability analysis are often overly complex. This paper constructs an equivalent impedance model for renewable energy integrated distribution power systems, proposing a static voltage analysis method for renewable energy integrated distribution power systems based on impedance model index. This method has been verified to be applicable not only to renewable energy single-infeed system but also to multi-infeed system. Furthermore, an analysis is conducted on the influence of the integration capacity, location of renewable energy, and the topology of networks on impedance model index, indicating that a higher impedance model index corresponds to greater static voltage stability margins in the system. Hence, during the planning of renewable energy integration, the plan with the highest impedance model index should be selected. Finally, the accuracy of the analysis methods and conclusions in this paper was validated based on the IEEE 14-node system.

Building energy consumption is the main urban energy consumption component, which mainly serves people-centered work and living energy demands. Based on the physical requirements of humans in urban buildings and to determine the comfortable body temperature in each season, this paper establishes a sizing optimization model of building-type integrated energy systems (IES), where the cooling and heating loads required to maintain indoor somatosensory body comfortable temperature are calculated. Depending on the external energy price, internal power balance and other constraints, the model develops an optimal sizing and capacity panning method of energy conversion and storage unit in a building-type IES with PV generation. The operating principle is described as follows: the PV generation is fully consumed, a gas engine satisfies the electric and thermal base load requirements, while the power system and a heat pump supply the remaining loads. The gas price, peak-valley electricity price gap and heat-topower ratio of gas engines are considered as important factors for the overall techno-economic analysis. The developed method is applied to optimize the economic performance of building-type IES and verified by practical examples. The results show that using the complementary characteristics of different energy conversion units is important to the overall IES cost.

Due to its high power, high efficiency, low pollution, and compact size, permanent magnet synchronous motors (PMSMs) have been widely used in a variety of fields, including electric vehicles, aerospace, wind turbines, and marine devices which are used in renewable, sustainable, and environmentally friendly energy resources. However, in these practical scenarios, the motor operating conditions are complex and variable. Under high temperatures and high current conditions, PMSMs may experience demagnetization failures, not only leading to performance degradation but also inducing unexpected failures of the motors. To reduce the risk of unexpected losses caused by demagnetization faults and improve the safety and reliability of motor systems, it is necessary to apply automated monitoring of the magnet flux of the motor's permanent magnets and achieve real-time diagnosis of early demagnetization faults, ensuring the safe operation of the motor. This review article tries to summarize the current detecting methods of the automated monitoring of demagnetization faults in PMSMs. The main online monitoring technologies from both practical and academic perspectives were summarized and their benefits and challenges have been reviewed. Finally, the research trends and suggestions for future improvements are provided. This review article will not only shed light on the origins of the automated monitoring of demagnetization faults but also help to design highly effective and sustainable permanent magnet synchronous motors.

The perceived poor performance of publicly traded companies on their sustainability commitments and the quality of sustainability reporting has prompted stakeholders to consider the economic, environmental, and social impacts of corporate activities. Economic activities have led to various threats in the form of climate change, pollution, greenhouse gas emissions, natural disasters, and other issues that have negatively impacted the environment and stakeholders. Companies are expected to report to stakeholders on their sustainability performance, but reality proves that present reporting falls below stakeholders’ expectations mainly due to its still voluntary nature. The present study aims to provide a literature review of the relationship between sustainability reporting and the role of companies governance, especially observing if climate change requirements and energy-needed changes are being accounted. Results highlight mixed evidence for the influence of board governance attributes, providing interesting insights for research advancement. The study has practical implications for businesses, regulators, governments, and other stakeholders in their policy deliberations and investment decisions. Further empirical studies are recommended to re-examine sustainability reporting using the variables identified as important factors and gaps in this study and other board characteristics to improve the generalizability of the results.

As a manifestation of technological innovation achievements, patents reflect the frontier of technological development in the field. This paper constructs a multi-entity patent collaboration network and analyzes its evolution patterns to provide a reference for innovation organizations to grasp the general direction of innovation development and select partners. Based on the data of collaboration patents of two and three organizations in China's new energy vehicles (NEV) industry from 2008 to 2021, this paper constructs higher-order interaction collaboration innovation networks in different periods to analyze the spatial evolution of networks and patent cooperation activities. The results show that the generalized degree distribution of nodes and edges conforms to the power-law distribution. The two-dimensional simplex networks gradually form triangle groups centered on the core nodes, and the importance of key edges is beginning to emerge. Key organizations and partners, including State Grid Corporation of China, Tsinghua University, and China Electric Power Research Institute, will largely determine the direction for the future development of cooperation innovation. The study also reveals that Beijing, Jiangsu, Zhejiang, Guangzhou, and Shanghai are in central positions in the cooperative innovation network, based on their cooperation breadth and depth measures. Additionally, key links formed by Beijing as hubs are not only the center of information exchange but also function as bridges that connect to other regions.

This paper evaluates an architectural design using an Energy Consumption consideration of Natural Ventilation in a hot dry climate (Khartoum State), at dwellings design applied. Method was used analysis of Autodesk IEVS software natural ventilation and energy consumption simulation. It resulted that to cooling, by natural ventilation in dwelling design used to get indoor temperature at the comfortable level during the summer. The Best-Case Situation of natural ventilation with consider of energy saving Based on the CFD simulation analysis, the performance of internal air velocity is approximately 0.7m/s. The wind velocity starts to slow down towards the rear of the apartment spaces. Approximately 95% of the internal areas have average air velocity between 0.43 m/s to 0.9 m/s. Internal Air flow pattern single floor house plan at Khartoum (Alazhari City); showing the internal air velocity of 0.7m/s near the window opening positions with the wind directions in the details and pressure of the air as worst-case situation, with velocity and temperature of the air with average 22o as a best-case situation. during a year. Architectural design process in the urban area of Alazhari City for dwelling towards to saving energy was applied and determined into an urban planning neighbourhood at Khartoum.

We have an unprecedented ability to map the Earth’s surface as deep learning technologies are applied to an abundance of high-frequency Earth observation data. Simple, free, and effective methods are needed to enable a variety of stakeholders to use these tools to improve scientific knowledge and decision making. Here we present a trained U-Net model that can map and delineate ground mounted solar arrays using publicly available Sentinel-2 imagery, and that requires minimal data pre-processing and no feature engineering. By using label overloading and image augmentation during training, the model is robust to temporal and spatial variation in imagery. The trained model achieved a precision and recall of 91.5% each and an intersection over union of 84.3% on independent validation data from two distinct geographies. This generalizability in space and time makes the model useful for repeatedly mapping solar arrays. We use this model to delineate all ground mounted solar arrays in North Carolina and the Chesapeake Bay watershed to illustrate how these methods can be used to quickly and easily produce accurate maps of solar infrastructure.

Brazil, Russia, China, India, and the Republic of South Africa (BRICS) represent developing economies facing different energy and economic development challenges. The current study aims to forecast energy consumption in BRICS at aggregate and disaggregate levels using the annual time series data set from 1992 to 2019 and to compare results obtained from a set of models. The time-series data are from the British Petroleum (BP-2019) Statistical Review of World Energy. The forecasting methodology bases on a novel Fractional-order Grey Model (FGM) with different order parameters. This study contributes to the literature by comparing the forecasting accuracy and the forecasting ability of the FGM(1,1) with traditional ones, like standard GM(1,1) and ARIMA(1,1,1) models. Also, it illustrates the view of BRICS's nexus of energy consumption at aggregate and disaggregates levels using the latest available data set, which will provide a reliable and broader perspective. The Diebold-Mariano test results confirmed the equal predictive ability of FGM(1,1) for a specific range of order parameters and the ARIMA(1,1,1) model and the usefulness of both approaches for energy consumption efficient forecasting.

CoO-ZnO-based composites have attracted considerable attention for the development of energy storage devices because of their multifunctional characterization and ease of integration with existing components. This paper reports the synthesis of CoO@ZnO (CZ) nanostructures on Ni foam by the CBD method for facile and eco-friendly supercapacitor applications. The formation of a CoO@ZnO electrode functioned with cobalt, zinc, nickel and oxygen groups was confirmed by X-ray diffraction, X-ray photoelectron spectroscopy, low and high-resolution of scanning electron microscopy, and transmission electron microscopy. The as-synthesized hierarchical nanocorn skeleton-like structure of CoO@ZnO-3h (CZ3h) electrode delivered a higher specific capacitance of 1136 F/g at a current density of 3 A/g with outstanding cycling stability, showing 98.3% capacitance retention over 3000 cycles in an aqueous 2 M KOH electrolyte solution. This retention was significantly better than that of other prepared electrodes, such as CoO (CO), ZnO (ZO), CoO@ZnO-1h (CZ1h), and CoO@ZnO-7h (CZ7h) (274, 383, 240 and 537 F/g, respectively). This superior capacitance was attributed to the ideal surface morphology of CZ3h, which is responsible for the rapid electron/ion transfer between the electrolyte and electrode surface area. The enhanced features of the CZ3h electrode highlight potential applications in high performance supercapacitors, solar cells, photocatalysis, and electrocatalysis.

Nowadays, all the stakeholders, policy makers, regulators, aircraft designers, producers, operators, etc.) are intensively working on development of the aircraft with full electric and hybrid propulsion systems. However, the technical, technological constrains (like limit on accumulator energy density) require introducing a new approach to conceptual design of such aircraft. The new methods is based on energy and mass balance evaluation. This paper analyses the identified constrains; integrates the energy and mass balance equations into the preliminary definition and calculations of the aircraft performance. By this way, the technological constrains might be transferred into the limitation on the aircraft energy and mass breakdown, that initiates a new approach to aircraft conceptual design uses the knowledge based multidisciplinary optimization. The paper describes the developed methodology for conceptual design of aircraft. It show results of implementing this new development philosophy to conceptual design of a four-seat small electric/hybrid aircraft and a special hybrid cargo UAV. The discussion of the results including got by using the emerging and enabling new technologies and new methods and solutions (including for example distributed propulsion system, unconventional forms, morphing, biomimics, etc.), demonstrates the possible implementation of the new development philosophy, new approach to aircraft conceptual design.

This thesis completion works it out to deepen into diverse modeling techniques for Point Absorbers. A combined frequency-time domain model is conceived, designed and developed in Matlab with Fortran as a base, leading to obtain physical variables of primary importance, namely position, velocity and power to energy net balance relationships of absorption. Integration of different degrees of freedom with heave as main executable leads in turn to a single buoy motion focus. Acquisition of the needed hydrodynamic coefficients is provided through application of NEMOH \& BEMIO solvers due to the Boundary Element Methodology. Initially, this Wave-to-motion model is validated by comparison with previous experimental results for a floating cone cylinder shape (Buldra-FO3). A single, generic, vertical floating cylinder is contemplated then, that responds to the action of the passing regular waves excitation. Later, two equally sized vertical floating cylinders aligned with the incident wave direction are modeled for a variable distance between the bodies. For both unidirectional regular and irregular waves as an input in deep water, we approximate the convolutive radiation force function term through the Prony method. By changing the spatial disposition of the axisymmetric buoys, using for instance triangular or rectangular shaped arrays of three and four bodies respectively, the study delves into motion characteristics for regular waves. The results highlight efficient layouts for maximizing the energy production whilst providing important insights into their performance, revealing displacement amplification- and capture width-ratios, while deriving in possible interpretations of scenarios related to the the known park effect. These terms are encompassed by the novelty of a new conceptual Post-Processing methodology in the field, which leads to obtain an optimal distance for the separated bodies with effective energy absorption in a regular wave regime. In conclusion, this computational excursion envisions and proposes potential fields of study, which will surely enhance new connections and link this renewable energy form.

From the standpoint of Neoliberal Institutionalism, this study explores Malaysia's participation in activities that make energy the topic and/or object of foreign policies, whether through bilateral or multilateral engagements. This research, which aims to evaluate the relevance of energy in Malaysia's economy and diplomacy and to explain Malaysia's reason for its involvement in these cooperations, is necessary because of Malaysia's growing involvement in the global energy market. Information for this study was gathered from a variety of government sources, interviews, published statistical data, and previous studies. The study demonstrates how vital energy is to Malaysia's economy. The Lao PDR-Thailand-Malaysia-Singapore Power Integration Project (LTMS-PIP) initiative, in which Malaysia is participating, is evidence of the viability of multilateral power commerce in the area. The Peninsula Gas Utilisation (PGU) pipeline in Peninsular Malaysia and the Four-Fuel Diversification Policy 1981 (4FDP 1981), which increases natural gas utilisation, are related to Malaysia's participation in the Malaysia-Thailand Joint Development Area (MT-JDA). Malaysia would want to think about streamlining its energy administration.

A photovoltaic-thermal (PVT) collector is a solar-based micro-cogeneration system which generates simultaneously heat and power for buildings. The novelty of this paper is to conduct energy and exergy analysis on PVT collector performance under two different European climate conditions. The performance of the PVT collector is compared to a PV panel. Finally, the PVT design is optimized in terms of thermal and electrical exergy efficiencies. The optimized PVT designs are compared to the PV panel performance as well. The main focus is to find out if the PVT is still competitive with the PV panel electrical output, after maximizing its thermal exergy efficiency. The PVT collector is modelled into Matlab/Simulink to evaluate its performance under varying weather conditions. The PV panel is modelled with the CARNOT toolbox library. The optimization is conducted using Matlab gamultiobj-function based on Non-Dominated Sorting Genetic Algorithm-II (NSGA-II). The results indicated 7.7% higher annual energy production in Strasbourg. However, the exergy analysis revealed a better quality of thermal energy in Tampere with 72.9% higher thermal exergy production. The electrical output of the PVT is higher than from the PV during the summer months. The thermal exergy- driven PVT design is still competitive compared to the PV panel electrical output.

Three-temperature heating systems consist of a heat engine and a heat pump, enabling thus maximum usage of the primary thermal source for the heating of buildings. This analysis has revealed obvious advantages and disadvantages that the combining of thermodynamic systems has in future development, also with respect to environmental and economic issues. It appears that the combination of a Stirling engine or a similar heat drive with a heat pump is especially suitable. In order to analyze the effectiveness of such a system, a comprehensive calculation procedure is used: its basis lies in accounting for all types of energy and their relationship to the original natural resource. The present paper aims to point out that the combination of Stirling engine and a heat pump is a useful solution thanks to the most favorable resultant economic impact if compared to the usage of a diesel, four-stroke gas, or, most commonly used, electric drive.

We demonstrate for the first time efficient mechanical to electrical energy conversion using InGaN/GaN nanowires (NWs). Using an atomic force microscope equipped with a modified Resiscope module, we analyse the piezoelectric energy generation of GaN NWs and demonstrate an important enhancement when integrating in their volume a thick In-rich InGaN insertion. The piezoelectric response of InGaN/GaN NWs can be tuned as a function of the InGaN insertion thickness and position in the NW volume. The energy harvesting is favoured by the presence of a PtSi/GaN Schottky diode which allows to efficiently collect the piezo-charges generated by InGaN/GaN NWs. Average output voltages up to 330 ± 70 mV and a maximum value of 470 mV per NW has been measured for nanostructures integrating 70 nm-thick InGaN insertion capped with a thin GaN top layer. This latter value establishes an increase of about 35% of the piezo-conversion capacity in comparison with binary p-doped GaN NWs. By considering these output signals, we estimate a maximum power density generated by one layer of dense InGaN/GaN-based NW of about 3.3 W/cm². These results settle the new state-of-the-art for piezo-generation from GaN-based NWs and offer a promising perspective for extending the performances of the piezoelectric sources.

The outbreak of SARS-COV-2 disease 2019 (COVID-19) abruptly changed the patterns in electricity consumption, challenging the system operations of forecasting and balancing supply and demand. This is due to the mitigation measures that include lockdown and Work from Home (WFH), which decreased the aggregated demand and remarkably altered its profile. Here, we characterise these changes with various quantitative markers and compare it with pre-COVID-19 business-as-usual data using Great Britain (GB) as a case study. The ripple effects on the generation portfolio, system frequency, forecasting accuracy and imbalance pricing are also analysed. An energy data extraction and pre-processing pipeline that can be used in a variety of similar studies is also presented. Analysis of the GB demand data during the March 2020 lockdown indicates that a shift to WFH will result to a net benefit for flexible stakeholders, such as consumer on variable tariffs. Furthermore, the analysis illustrates a need for faster and more frequent balancing actions, as a result of the increased share of renewable energy in the generation mix. This new equilibrium of energy demand and supply will require a redesign of the existing balancing mechanisms as well as the longer-term power system planning strategies.

Human and animal waste, including waste products originating from human or animal digestive systems such as urine, feces, and animal manure, have constituted a nuisance to the environment. Inappropriate disposal and poor sanitation of human and animal waste often cause negative impacts on human health through contamination of the terrestrial environment, soil, and water bodies. Therefore, it is necessary to convert these wastes into useful resources to mitigate their adverse environmental effect. The present study provides an overview and research progress of different thermochemical and biological conversion pathways for the transformation of human- and animal-derived waste into valuable resources. The physicochemical properties of human and animal waste are meticulously discussed as well as nutrient recovery strategies. In addition, a bibliometric analysis is provided to identify the trends in research and knowledge gaps. The results reveal that the U.S.A, China and England are the dominant countries in the research areas related to resource recovery from human or animal waste. In addition, researchers from the University of Illinois, the University of California Davis, the Chinese Academy of Science and Zhejiang University are front runners in research related to these areas. Future research should be centred on developing technologies for the on-site recovery of resources, exploring integrated resource recovery pathways, and exploring different safe waste processing methods.

The sustainable management of Land - Water - Energy - Food (LWEF) nexus requires an envi-ronmental characterization that allows the comparison of complex interlinkages between nexus resources and livelihoods. This complexity makes this characterization difficult coupled with limited study in quantifying sustainability of LWEF nexus and its linkage with livelihood. Therefore, the present study aimed to investigate the link between sustainable LWEF nexus and livelihoods. We used analytical hierarchy process and pairwise comparison matrix in combina-tion with weighting model. The result of composite LWEF nexus index was 0.083 representing, low sustainability. This could be linked with nexus resources consumption, use, and manage-ment. From the analysis of the weight of land, water, energy and food nexus resources, the highest weight was observed for food. The focus of on food production only shows no clear synergy on provisioning, supporting or regulating nexus resources to address livelihoods. The result further showed that LWEF nexus resources have strong correlation with livelihoods. This was evidenced by social (r>0.8, P<0.01), natural (r>0.3, P<0.05) and physical (r>0.6, P<0.01) liveli-hood indicators showed strong positive correlation with LWEF nexus resources. From this re-sults, it was observed that managing nexus resources not only provide a significant contribution to achieve sustainable LWEF nexus, but also be effective for enhancing livelihood through food security. This could be attained by strong evidence based policy to ensure sustainable use of nexus resources. The results provided by this study would serve as the foundation for future study, policy formulation and implementation.

Reducing the construction time for large logistics buildings can result in reduced construction management costs and economic gains from early operation. A large logistic building with a heavy load and long spans was constructed as a precast concrete (PC) structure, which requires the use of a sizable crane to lift heavy PC members. A basic analytical approach is employed to resolve potential errors in the planning of PC member erection and to build a systematic erection plan. Calculation techniques for the trajectory distance, which use the crane location, are applied to select an erection plan that minimizes crane work. A crane trajectory distance calculation algorithm for sustainable PC member erection in large logistic buildings with heavy loads and long spans has been developed. The developed model aids in creating simulation and optimization models to ensure minimal usage of cranes in the future and determining cost, construction time, CO2 emissions, and energy use for each erection plan.

Integrated energy systems (IES) seek to minimize power generating costs in future power grids through the dynamic coupling of different energy technologies. To accommodate fluctuations in load demand due to the penetration of renewable energy sources, flexible operation capabilities must be fully exploited, i.e., even power plants that are traditionally considered as base-load units need to be operated according to unconventional paradigms. Thermomechanical loads induced by frequent power adjustments can accelerate the wear and tear of components. If a unit is flexibly operated without respecting limits on materials and components, the risk of failures of expensive components will eventually increase, nullifying the additional profits ensured by flexible operation. In addition to the limits on power variations (explicit constraints), the solution of the unit dispatch problem needs to meet the limits on temperature, pressure and flow rate variations (implicit constraints). The FARM (Feasible Actuator Range Modifier) module was developed to enable existing optimization algorithms to identify solutions to the unit dispatch problem that are both economically favorable and technologically sustainable. Thanks to the iterative dispatcher-validator scheme, FARM permits addressing all the imposed constraints without excessively increasing the computational costs. In this work, the algorithms constituting the module are described, and the performance was assessed by solving the unit dispatch problem for an IES composed of three units, i.e., Balance of Plant, Gas Turbine, High-Temperature Steam Electrolysis. Finally, FARM module provides dedicated tools for visualizing the response of the process variables of interest during operation transients and a tool aiding the operator at making decisions. These techniques might represent the first step towards the deployment of an Ecological Interface Design (EID) for IES units.

In this paper, four probability functions are compared with the purpose of establishing a methodology to improve the accuracy of the estimated wind energy in a desert city in northwestern Mexico. For the statistical modeling, 3 time series of wind speed data were used, corresponding to the years 2017, 2018, and 2019, recorded with a sonic anemometer at a sampling frequency of 10 Hz. From these, the analysis is performed with different stationarity periods (5, 30, 60, and 600 seconds). The estimation of the parameters characterizing the probability density functions was performed using different methods; the statistical models were evaluated by the coefficient of determination and the Nash-Sutcliffe efficiency coefficient, while their accuracy by the measured quadratic error, the mean square error, the mean absolute error, and the mean absolute percentage error. It was found that Weibull with the energy pattern factor method and Gamma using the method of moments were the probability density functions that best describe the statistical behavior of the wind speed and, therefore, better estimate the energy generated, so it is concluded that the proposed methodology will allow having greater confidence, both in the estimation of the wind speed and in the small wind energy available for its use.

The study presents empirical results investigating the relationships among renewable and non-renewable energy consumption, CO2 emissions, and GDP within the Visegrád Group (V4) countries. Using FMOLS/DOLS and ARDL approaches, along with causality tests based on the Toda-Yamamoto method, the study explores these relationships at a regional level. The findings indicate that renewable energy has a small positive impact on long-term economic growth, with non-renewable energy having a more significant effect. Moreover, CO2 emissions have a negative impact on economic growth, suggesting ongoing reliance on non-renewable energy sources and a burden on economic expansion. On an individual country level, the effects vary. Poland, Slovakia, and Hungary exhibit a negative relationship between CO2 emissions and economic growth. Energy sources also differ in impact: in Poland, the Czech Republic, and Slovakia, non-renewable energy significantly affects economic growth, while in Hungary, renewable energy plays a more substantial role. Causality tests reveal a causal relationship between CO2 emissions and economic growth in the Czech Republic and Poland, suggesting CO2 emissions significantly influence economic expansion. In terms of energy production, renewable energy is causally related to economic growth in the Czech Republic and Slovakia. All countries demonstrate significant causality between non-renewable energy and economic growth. Additionally, a relationship between renewable energy and CO2 emissions is confirmed in Poland.

Many buildings built before the energy performance regulations are in a situation of thermal discomfort and energy inefficiency. The creation of intelligent environments advances towards new opportunities, based on real-time monitoring and on the development of sensors and technologies. Furthermore, the standards for building automation and electronic systems enable interoperability and interconnection between control devices and systems. The application of soft computing has significantly improved the energy efficiency, however, requires prior assessment to design the automation functions. Temperature, humidity, air quality, occupancy and energy consumption are the most common measured parameters, but the relationship with other operational variables such as occupancy or some building states remains as a research challenge. This article presents a methodology to develop the automatization of an existing large public building. The methodology consists of three stages: 1. Assessment and diagnosis to set appropriate actions using EN ISO 52120-1. 2. EN 50090 for open communication networks, and EN ISO 52120-1 to assign the technical building management. 3. System control deploying of low-cost and low-consumption input and output devices. It has been proved that it is possible to effectively automate an obsolete building with a low cost, open source system that can be easily applied in other buildings.

As the structure of horizontal gas wells is more complicated than that of vertical wells, the form of the liquid-carrying in different sections does not well agree. This makes it problematic to apply the widely used liquid-carrying theory of vertical gas wells in horizontal gas wells. Since the theory focused on the critical gas flow rate, it cannot quantify how much liquid it can remove. Simultaneously, it ignores the fact that the liquid-carrying ability of gas flow is limited and the producing liquid has a certain amount of flowing energy. In this study, the gas-liquid flow law of horizontal gas wells and wellhead drainage stability in different tubing depths were firstly studied. Then, the stability of gas drainage for different tubing depths was analyzed and confirmed. Given the disadvantages of the typical theory of critical gas flow, the mathematical model of different tubing depths for gas drainage is established for horizontal gas wells. The innovative model could take the energy of gas flow and liquid flow into account, and quantify the liquid volume which was removed. By verifying the model with the experiments, the result showed that the relative error of the model is generally less than 10%. It shows the research could provide a scientific basis for the analysis and liquid-carrying capacity for horizontal gas wells.

China's gradually increasing assertiveness at the international level marked the beginning of several influential geopolitical projects. The biggest of these is the Belt and Road Initiative, which will be the subject of this post. The Chinese government initiated the BRI in 2013 to revive the historic Silk Road. The name of the new initiative was chosen based on well-known historical parallels, emphasizing the ideological component of China's current position. At the same time, neo-mercantilism prevails in China, and we can say that all roads lead to China, which means that the current nature of Chinese strategic planning corresponds to the increasingly important role of the state in international relations and strengthens its position in the world economy. The aim of the paper is to use the methods of analysis, synthesis, deduction, induction, comparison, and explanation to analyse Chinese investments that flow into various sectors worldwide, but especially into the countries participating in the Belt and Road Initiative from 2013 to the present. The largest such sector is the energy sector, which we will look at in more detail in the post. Finally, the contribution will be focused on predicting the development of further investments based on the available information as well as our own suggestions and recommendations to make them more efficient.

The ongoing electrification of the heat and transport sectors is expected to lead to a substantial increase in peak electricity demand over the coming decades, which may drive significant investment in network reinforcement in order to maintain a secure supply of electricity to consumers. The traditional way of security provision has been based on conventional investments such as the upgrade of the capacity of electricity transmission or distribution lines. However, the energy storage technology can also provide security of supply, thereby constituting a cost-efficient alternative to expensive conventional reinforcements. In this context, the current paper presents a methodology for the economic quantification of the security contribution of energy storage. This methodology makes use of mathematical optimization for the calculation of the F-factor metric, which reflects the optimal amount of peak demand reduction as compared to the power capability of the energy storage asset. In this context, a case study is presented in which the security contribution of energy storage is analyzed as a function of its power capability, energy capacity and efficiency as well as of characteristics of load patterns.

A new Pd(II) complex of the previously reported ligand N,N′-bis[(2,2′-dihydroxybiphen-3-yl)methyl]-N,N′-dimethylethylenediamine (L) was obtained from a DMF/H2O mixture. It differs from a Pd(II) complex of L previously obtained by sole DMF. The roles in the solid state assembly of solvent molecules and molecular conformation (driven by specific transition metal ions) were studied by comparing six complexes of L containing different metal centers (Ni(II), Cd(II), Cu(II), Pd(II)). Hirshfeld surface analysis, 2D fingerprint plots and energy frameworks calculations were used to investigate the intermolecular interactions within the crystal packing of the six complexes. As suggested by interaction energies, Pd(II) and Ni(II) complexes arrange to form ribbons, while Cd(II) and Cu(II) complexes form 3D networks. Interactions between complexes and solvent molecules in the previous Pd(II) complex are replaced by complex-complex interactions in the new Pd(II) complex, while BuOH and MeOH are interchangeable in the interactions within the crystal packing of the two Ni(II) complexes. Finally, solvent molecules are not involved in the crystal packing of the Cu(II) complex. The present study suggested that the solid state assembly of these systems is mainly driven by the molecular conformation, that depends in turn by the metal ion involved, while the solvent only plays a minor role.

In the development of power systems it is indicated very often, that transformation of power systems should be carried out in accordance with the idea of energy democracy. This will develop energy communities, that are trying to meet energy needs by using local renewable generation sources. This may result with a temporary low load on the MV lines connecting the community grid and the power system. Such state may cause incorrect operation of power protection systems. This can cause an extended protection operation time, due to decision algorithms inactivity at low values of measurement currents. Therefore, the detailed MV lines overcurrent digital protection model and a dynamic model of the power network were developed. The simulation results are showing that the settings of the parameters activating the protection decision algorithms affect their operation time in dynamic conditions. The conclusion is that the development of the power protection automatics must be carried out in the same time (preferably in advance) with the change of the power system operation model. This is very important for future power systems with high penetration energy communities and renewable generation sources.

Excitotoxicity related to the dysfunction of the N-methyl-d-aspartate receptor (NMDAR) has been indicated to play an integral role in the pathophysiology of multiple disease states, including neurodegenerative disorders such as Parkinson’s disease. There is a notable gap in the market for novel NMDAR antagonists, however current methods to analyze potential antagonists rely on indirect measurements of calcium flux and hazardous radioligand binding assays. Recently, a fluorescent NMDAR ligand, N-adamantan-1-yl-dimethylamino-1-naphthalenesulfonic acid, known as AM-DAN was developed by our group. Additional studies on this ligand is necessary to evaluate its potential as a biological tool in NMDAR research. Therefore, this study was aimed at conducting structural analyses, fluorescence experiments, high-accuracy NMDAR molecular modelling and NMDAR phencyclidine (PCP) site competition binding studies using AM-DAN. Results revealed that AM-DAN has appropriate structural properties, significant fluorescent ability in various solvents and is able to bind selectively and compete for the PCP-binding site of the NMDAR. Therefore, AM-DAN holds promise as a novel fluorescent ligand to measure the affinity of prospective drugs binding at the NMDAR PCP-site and may circumvent the use of radioligands.

By employing the stochastic extension of the Madelung quantum-hydrodynamic description within a discrete methodology, we establish a solution using the path integral approach to explore the progression of quantum states' superposition. This investigation aims to understand the eventual establishment of a stable end-state configuration amid the backdrop of gravitational background fluctuations. The model identifies the circumstances that lead to a limited range of interaction for the quantum potential, allowing for the emergence of sizeable, classically described macroscopic phenomena. The theory unveils the lowest achievable level of uncertainty in an open quantum system and investigate its congruence with the localized behaviors of macroscopic classical systems. The study examines agreements and differences with decoherence theory and the Copenhagen interpretation of quantum mechanics, and evaluates the impact of wave function decay on the measurement process.

The heavy metal lead (Pb) can irreversibly damage the human nervous system. To help understand Pb-induced damage, we applied a genetically encoded Förster resonance energy transfer (FRET)-based Pb biosensor Met-lead 1.44 M1 to two living systems to monitor the concentration of Pb: induced pluripotent stem cell (iPSC)-derived cardiomyocytes as a semi-tissue platform, and Drosophila melanogaster fruit flies as an in vivo animal model. Different FRET imaging modalities were used to obtain FRET signals, which represented the presence of Pb in the tested samples in different spatial dimensions. Using iPSC-derived cardiomyocytes, the relationship between beating activity (20–24 beats per minute, bpm) determined from the fluctuation of fluorescent signals and the concentrations of Pb represented by the FRET emission ratio values of Met-lead 1.44 M1 was revealed from simultaneous measurements. Pb (50 μM) affected the beating activity of cardiomyocytes, whereas two drugs that stop the entry of Pb differentially affected this beating activity: verapamil (2 μM) did not reverse the cessation of beating, whereas 2-APB (50 μM) partially restored this activity (16 bpm). The results clearly demonstrate a potential of this biosensor system as an anti-Pb drug screening application. In the Drosophila model, Pb was detected within the adult brain or larval central nervous system (Cha-gal4>UAS-Met-lead 1.44 M1) using fast epifluorescence and high-resolution two-photon 3D FRET ratio image systems. The tissue-specific expression of Pb biosensors provides an excellent opportunity to explore the possible Pb-specific populations within living organisms. We believe that this integrated Pb biosensor system can be applied to the prevention of Pb poisoning and advanced research on Pb neurotoxicology.

The energy E takes the place of the gravitational mass m_G to produce gravity [1]. We wonder whether the inertial mass m_i in the inertial force is also replaced by E. The experiments to measure the inertial force and weight of a carrier are presented. Now we can test the principle of equivalence and study foundations of physics in condensed matter.

This paper presents the results of aerodynamical performance research focused on maintaining the thermal comfort and increasing the energy efficiency of a typical social housing unit located in a high-density urban area. Bioclimatic design strategies are used to develop a sustainable and economic technology in existing housing clusters in Mexico City. A full-scale prototype, built on campus facilities, was used to study the flow conditions around the design. All scaled prototypes implement similar criterion. Furthermore, a scaled prototype is evaluated within a low speed wind tunnel installation. Additionally, numerical simulations were performed at transient state based on previous physical measurements and historical local climatic conditions to determine preferable modifications.

Seaports are well known as the medium that has evolved into the central link between sea and land for complex marine activities. The growth in maritime logistics especially necessitates a large volume of energy supply to maintain the operation of sea trade, resulting in an imbalance between the generation and demand sides. Future projections for three major concerns show an increase in load demand, cost of operation, and environmental issues. In order to overcome these problems, integrating microgrids as an innovative technology in the seaport power system appears to be a vital strategy. It is believed that microgrids enhance the seaport operation by providing sustainable, environmentally friendly, and cost-effective energy. Despite the fact that microgrids are well established and widely used in a variety of operations on land, their incorporation into the seaport is still limited. The involvement of a variety of heavy loads such as all-electric ships, cranes, cold ironing, and buildings infrastructure makes it a complicated arrangement task in several aspects, which necessitate further research and leave space for improvement. In this paper, an overview of the seaport microgrids in terms of their concepts, requirements, and operation management is presented. It provides the perspectives of integrating the microgrid concept into a seaport from both shore side and seaside as a smart initiative for the green ports vision. Future research directions are discussed towards the development of more efficient marine power system.

The antioxidant activity of molecules constitutes an important factor for the regulation of redox homeostasis and reduction of oxidative stress. Cells affected by oxidative stress can undergo genetic alteration, causing structural changes and promoting the onset of chronic diseases, such as cancer. The in silico study performed here was developed to evaluate the antioxidant potential of two molecules, ZINC08706191 (Z91) and ZINC08992920 (Z20), with recognized epithelial anticancer potential. Molecular docking, chemical-quantum calculations and Pearson's correlation were performed. The Z91 and Z20 molecules showed lower binding free energy (ΔG) values for the receptor-ligand interaction than the reference molecules (caffeine – CAF and ascorbic acid – AA), and better results for values of molecular descriptors correlated with ΔG, resulting in a decrease of ΔG. Strong correlations were observed between ΔG values for the five receptors evaluated and ΔG values of the potential epithelial anticancer activity available in literature. These results attest to the significant antioxidant potential of the Z91 and Z20 molecules and their strong relation with the potential epithelial anticancer activity and may be indicated for further analysis in relation to the control of oxidative stress and epithelial anticancer activity.

Tropical regions face significant energy challenges due to climatic conditions. This study investigates the interplay between sustainable architecture and building energy regulations in mitigating these challenges. The study aims to assess the effectiveness of existing building energy regulations in promoting sustainable architecture in tropical climates and identify key architectural strategies and regulatory frameworks for optimizing energy efficiency in tropical buildings. A comparative analysis of building regulations and case studies of sustainable buildings in selected tropical regions is conducted. The findings reveal that current regulations often must be revised to address tropical climates' unique energy demands. Incorporating passive design principles, renewable energy systems, and material selection is crucial for energy efficiency. It is recommended that building energy regulations be strengthened to mandate sustainable design strategies and provide incentives to promote the adoption of energy-efficient technologies.

Automated systems, regulated by algorithmic protocols and predefined set-points for feedback control, require the oversight and fine-tuning of skilled technicians. This necessity is particularly pronounced in automated greenhouses, where optimal environmental conditions depend on the specialized knowledge of dedicated technicians, emphasizing the need for expert involvement during installation and maintenance. To address these challenges, this study proposes the integration of data acquisition technologies using Internet of Things (IoT) protocols and optimization services via Reinforcement Learning (RL) methodologies. The proposed model was tested in an industrial production greenhouse for the cultivation of industrial hemp, applying adapted strategies to the crop, and was guided by an agronomic technician knowledgeable about the plant. The expertise of this technician was crucial in transferring the RL model to a real-world automated greenhouse equipped with IoT technology. The study concludes that the integration of IoT and RL technologies is effective, validating the model's ability to manage and optimize greenhouse operations efficiently and adapt to different types of crops. Moreover, this integration not only enhances operational efficiency but also reduces the need for constant human intervention, thereby minimizing labor costs and increasing scalability for larger agricultural enterprises. Furthermore, the RL-based control has demonstrated its ability to maintain selected temperatures and achieve energy savings compared to classical control methods.

The development of novel ionic liquid crystals for energy storage applications has gained significant attention in recent years due to their potential to develop the field of energy storage. Ionic liquid crystals represent a unique class of materials with high ionic conductivity and thermal stability, making them ideal candidates for use in advanced energy storage devices. This research aims to explore the fundamental properties, structure and liquid crystals performance of these novel materials, with the goal of advancing their practical application in next-generation energy storage technologies. By understanding the structure-function relationship of ionic liquid crystals, researchers can tailor their properties to meet specific energy storage requirements, such as high energy density, fast charging capabilities, and long cycle life. This study seeks to contribute to the growing body of knowledge in the field of energy storage by investigating the potential of novel ionic liquid crystals as efficient and sustainable energy storage solutions. The two ionic liquid crystals show mesomorphic behavior and typical zwitterion characteristics that revealed by the cyclic voltammetry techniques. These materials uploaded with lithium ions for more stability and higher ionic conductivity.

Dual-energy CT (DECT) imaging has broadened the potential of CT imaging by offering multiple postprocessing datasets with a single acquisition at more than one energy level. DECT shows profound capabilities to improve diagnosis based on its superior material differentiation and its quantitative value. However, the potential of dual energy imaging remains relatively untapped, possibly due to its intricate workflow and intrinsic technical limitations of DECT. Knowing the clinical advantages of dual-energy imaging and recognizing its limitations and pitfalls is neces-sary for an appropriate clinical use. The aims of this paper are to review physical and technical basis of DECT acquisition and analysis, to discuss advantages and limitations of DECT in dif-ferent clinical scenarios, to review technical constraints in material labeling and quantification, and to evaluate cutting-edge applications of DECT imaging, including artificial intelligence, qualitative and quantitative imaging biomarkers, and DECT-derived radiomics and radioge-nomics

In this work, we explore new constraints on phantom scalar field cosmologies with a scalar field employing early times catalogues related to CMB measurements, along with the local standard observables, like Supernovae Type Ia (SNIa), H(z) measurements (Cosmic Clocks), and Baryon Acoustic Oscillations (BAO) baselines. In particular, we studied a tracker phantom field with hyperbolic polar coordinates that have been proposed in the literature. The main goal is to obtain precise cosmological constraints for H0 and σ8, in comparison to other constructions that present tension in early cosmological parameters. Our results show that phantom scalar field cosmologies have a reduced statistical tension on H0 that it is less than 3σ using model-independent CMB catalogues as SPT-3G+WMAP9 and ACTPol DR-4+WMAP9 baselines. This suggests these models using a different phantom potential might address the Hubble constant problem and reduce the systematics involved.

Resource pricing in cloud computing has become one of the main challenges for cloud providers. The challenge is determining a fair and appropriate price to satisfy users and resource providers. To determine a fair price, it is necessary to consider the conditions and needs of both parties: provider and user. This research tries to provide a pricing mechanism for cloud computing based on game theory. The proposed mechanism takes into account three factors including fault possibility, interaction between virtual machines, and energy consumption to reach a fair price. In the proposed game, the provider decides on the price of the virtual machine which can be offered to the user on each physical machine and the user decides between the virtual machines offered to run its application. The whole game is implemented as a function of the resource broker component. The proposed mechanism is simulated and evaluated using the CloudSim simulator. Its performance is compared with several previous recent mechanisms. According to the results, the proposed mechanism has been able to determine a more reasonable price for the user and the provider which increases the overall profitability of the cloud system.

Among the electrochemical energy storage (EES) technologies, rechargeable batteries (RBs) and supercapacitors (SCs) are the two most desired candidates for powering a range of electrical and electronic devices. The RB operates on Faradaic processes, whereas the underlying mechanisms of the SC vary as non-Faradaic in the electrical double layer capacitors (EDLCs), Faradaic at the surface of the electrodes in the pseudo capacitors (PCs), and a combination of both non-Faradaic and Faradaic in the hybrid capacitors. The EDLCs offer high power density but low energy density. The hybrid capacitors take advantage of the Faradaic process without compromising their capacitive nature. Unlike batteries, supercapacitors provide high power density and numerous charge-discharge cycles; however, their energy density lags that of batteries. Here, we review recently published critically selected articles on supercapatteries, a generic term that refers to EES devices that can combine the merits of EDLCs and RBs. Also discussed are the properties, design strategies, and future perspectives of supercapatteries.

As urbanization continues to accelerate, the concept of smart buildings has transitioned from a futuristic vision to an integral component of modern cities. These buildings, often seen as the building blocks of smart cities, are increasingly relying on cutting-edge technologies like 5G and cloud computing to reach unprecedented levels of energy efficiency, sustainability, and occupant comfort. This paper offers a comprehensive exploration into the marriage of smart building technologies with 5G and cloud computing. It scrutinizes the individual and combined impacts of these technologies, presents various case studies showcasing real-world applications, and anticipates future trends. Moreover, it delves into technical challenges, policy implications, and offers concrete recommendations for stakeholders.

Studies involving vortex in hybrid superconducting devices and their interaction with different components inside the sample are an important issue to reach higher values of their critical parameters in superconducting materials. The vortex distribution on each side of sample with different fundamental parameters, such as temperature T, penetration depth λ, coherence length ξ, electron mass m and the order parameter Ψ, may help to improve the superconducting properties. Thus, in this work, we used the modified Ginzburg-Landau theory to investigate hybrid superconductor (HS), but also to provide a highly tunable and adjustable theoretical tool to theoretically explain the experimental results involving HS, in order to study the vortex behaviour in superconductors of mesoscopic dimensions with extremely differences among their fundamentals parameters. Therefore, we evaluated the influence of HS on vortex configuration and their effects in the field-dependent magnetization. The results show that the during the increment of applied magnetic field H the diamagnetic response of HS, Meissner effect, include additional jumps of magnetization while diamagnetism continues its increase in the sample. In addition, the differences among parameters, create an interface between both components, two different magnitudes of supercurrent and vortex sizes producing a lower degradation of local superconductivity, which increase the upper critical field. On the other hand, this type HS with differences of parameters on both sides can be used to control the vortex movement in the selected superconducting region sample with more accuracy.

The present paper reports an exact approach quantifying the electromagnetic contribution to the anomalous magnetic moment occurring in isolated system comprised of non-composite particle carrying elementary electric charge. Essential averaging procedure and regularization of the electromagnetic field potentials necessary when quantifying the electromagnetic self-interactions and when deriving equations of motion without singularities and obeying the conservation laws are thoroughly discussed. The study shows that the dynamics of the considered system is associated to unique classical transcendental equations of motion satisfied by the particle's velocity and the electromagnetic contribution to the anomalous $g$-factor known from the quantum electrodynamics. The equations of motion lead to an exact analytical expression for the anomalous $g$-factor that provides more accurate result than that calculated with the aid of quantum electrodynamics. It matches the experimentally measured value reported in the literature to a one part per trillion. We obtain a_e=0.00115965218000(65) thus reveling the potential of non-perturbative, non-probability methods in predicting the electron's anomalous g-factor.

The study investigates the impact of globalization, renewable energy consumption and economic growth on CO2 emissions in 26 European Union (EU) countries for the period 1990-2020. The second-generation panel unit root tests are applied, the Westerlund cointegration test is used, and panel Fully Modified Least Squares (FMOLS) and Dynamic Ordinary Least Squares (DOLS) techniques are employed to estimate the long-term relationship between variables. The causality relationship among variables under investigation is identified by the heterogeneous Dumitrescu-Hurlin causality test. It is found that globalization and renewable energy consumption contributed to the carbon emissions mitigation, while economic growth induced their increase. The results are robust when control variables (i.e., financial development, foreign direct investment and urbanization) are added in the model. Foreign direct investment and urbanization are contributors to carbon emissions increase whereas financial development induce their decrease. The effect of variables under consideration on carbon emissions is differentiated by the economic development and institutional quality level. Unidirectional causalities relationships were identified from globalization to carbon emissions and from carbon emissions to foreign direct investment and bidirectional relationships between economic growth, renewable energy consumption, financial development and carbon emissions. Policy implications of the findings are also discussed.

With the swift advancement of wearable electronic devices and the electronic textile industry, the energy storage components of these devices must possess the capability to maintain stable mechanical and chemical properties even after undergoing multiple bending or tensile deformations. This circumstance has expedited research efforts toward novel materials, processing techniques, and designs for flexible energy storage devices. Among the myriad of materials investigated thus far, biomass-derived architectures have garnered significant attention due to renewability, cost-effectiveness, and abundance in earthly resources. Notably, flexible carbon membrane/ monolithic derived from biomass serve as a particularly promising option for self-supporting electrodes, align seamlessly with the requirements of next-generation electronic devices, and obviate the need for additional costs, unnecessary weight, and the high contact resistance that additive insulating adhesives may entail. This review delves into the comprehensive analysis of biomass feedstocks and methodologies employed in the synthesis of flexible self-supporting carbon electrodes. Subsequently, the advancements in their application in energy storage devices are elucidated. Finally, an outlook on the potential of biomass self-supported carbon architectures and the challenges they face is provided.

The shortage of precooling equipment in litchi producing regions could lead to a high loss rate, poor quality of litchis. It is urgent to develop a portable precooling device for litchi producing regions. In this study, a novel spray hydrocooler with thermal energy storage (TES) were designed, fabricated, and tested. A simple mathematical model of TES capacity, ice coil thermal resistance and refrigeration system was employed to determine hydrocooler parameters. Then designed the structure of the spray hydrocooler. Maximum charging test was implemented with full TES capacity and litchi spray hydrocooling experiments were carried out at different charging times, spray flow rate, and litchi load with one-third TES capacity. Results showed that: (1) the spray hydrocooler allows for the rapid and effective precooling of litchis; (2) the hydrocooler can precool 299 kg litchis with one-third TES storage, meet the precooling requirements; (3) the effective TES capacity achieved 1.25×108 J at the maximum TES capacity of the hydrocooler, while the energy efficiency ratio (EER) is 2; (4) the precooling capacity was maximum and the average power consumption was minimum when the litchi load was 23 kg and the spray flow rate was 30 L min-1. Longer charging time is the most important factor in increasing precooling capacity and reducing average power consumption.

Electric energy is one of the driving forces in every country. The supply of electrical energy continues to present various challenges, such as high costs associated with procuring raw materials for generation, sparsely populated areas that are not connected to the main grid, and the need for infrastructure to support generation and network delivery. These challenges have contributed to the growing adoption of renewable energy sources, particularly solar photovoltaics (PV).In this study, we have developed a practical method to assess the spatial PV potential in a selected urban area. The methodology combines data collected from an unmanned aerial vehicle (UAV) photogrammetry, Geographic Information System (GIS), and the energy output from three remote photovoltaic systems installed at different locations. The results obtained from this approach not only provide the energy generated per square meter, per year (kWh m-2 yr-1), but also provides a base to calculate the potential distance that electric cars could travel based on the energy generated. To illustrate the application of this method, two practical cases were selected: Senglea, Malta, and Munxar, Gozo. These examples highlight the versatility and effectiveness of our approach for evaluating and harnessing solar energy through photovoltaic panels in different contexts.

The increased interest in space activities, structural health monitoring, and terrestrial monitoring in hostile and inaccessible zones places a high demand for energy sources for autonomous systems. Conventional electrochemical batteries that could be used are plagued by low energy storage density, short life, disposal of unwanted batteries, and related undesired recharging or replacement maintenance requirements, which endangers the environment. Fuel cells and solar energy sources being exploited to mitigate the adverse effect of environmental threats posed by batteries and fossil fuels are costly to acquire and maintain. The availability of energy sources derived from waste heat from radioactive decay for domestic appliances and industrial equipment will also help alleviate the effects of climate change, which continues to threaten the environment due to fossil fuel energy-based sources that emit harmful carbon monoxide into the atmosphere. A combination of energy from waste heat, harvested via thermoelectricity and existing battery technology to produce a hybrid energy source, can guarantee secured energy for an extended period. Based on the Seebeck effect, thermoelectric energy generation may considerably contribute to sustainable energy development and meet the power demand for spacecraft applications. Modeling of the energy from waste heat, the Li-ion battery, and a hybrid energy source are considered, and their performances are established using the MATLAB/Simulink environment. Results confirmed the comparative advantage of the hybrid energy source over and above the respective electrochemical batteries and waste heat energy sources regarding effectiveness and performance efficiency. Since batteries are required to operate in a constantly changing environment, the effects of temperatures on batteries were investigated. The results show that the performances of batteries decrease with a decrease in ambient temperature and that the higher the maximum operating capacity, the higher the battery's internal temperature.

Nanostructured dipeptide self-assemblies exhibiting quantum confinement are of great interest due to their potential applications in the field of materials science as optoelectronic materials for energy harvesting devices. Among those, aromatic cyclo-dipeptides containing the amino acid tryptophan are wide-band gap semiconductors displaying high mechanical rigidity, photoluminescence and piezoelectric properties to be used in power generation. In this work, we report the fabrication of hybrid systems based on chiral cyclo-dipeptide L-Tryptophan- L-Tryptophan incorporated into biopolymer electrospun fibers. The micro/nanofibers contain self-assembled nanospheres embedded into the polymer matrix are wide-band gap semiconductors (gap energy 3.8 eV), display blue photoluminescence and relevant piezoelectric and pyroelectric properties with coefficients as high as 57 pCN-1 and 35×10-6 Cm-2k-1, respectively. They are therefore promise systems for thermal sensing and energy harvesting applications.

Transparent conductive electrodes (TCEs) are of enormous significance to the emergence of flexible and wearable electronics and continued growth of modern devices. Versatile and tunable TCEs, featuring with not only high optical transmittance but also intriguing features of electrochemical energy-storage capability, remain a significant challenge. Here we develop capacitive active films comprised of graphene-conjugated V2O5@poly (3,4-ethylene dioxythiophene) ternary composite (V2O5@PEDOT/rGO) on silver nanowire coated substrates as solid-state super/pseudocapacitors. The constructed electrodes exhibit improved electrolyte ions interaction with effective graphene layer, achieving high areal capacitance 0.6-1.2 mF.cm−2 with 0.5M LiCl electrolytes at optical transparency >60% with record durability. As demonstrated, the kinetic blocking of PEDOT layer and anchoring capability of graphene upon amphoteric soluble vanadium ions from layered V2O5 nanoribbons/nanobelts contribute synergistically to the unusual electrochemical stability, also shown using scanning electrochemical microscopy (SECM) providing electroactivity sites and ion transportation rates. As-fabricated symmetric solid-state supercapacitors delivered broad potential window >1.4 V under two different electrolyte environments (aqueous LiCl and LiCl/PVA gel) and demonstrated higher power and energy density (0.27 μWh.cm−2) outperforming previously reported devices at <0.1 μWh.cm−2. The electrochemical properties are also discussed in terms of solvation in polymer gel electrolyte ions.

In this paper we present AWEbox, a Python toolbox for modeling and optimal control of multi-aircraft systems for airborne wind energy (AWE). AWEbox provides an implementation of optimization-friendly multi-aircraft AWE dynamics for a wide range of system architectures and modeling options. It automatically formulates typical AWE optimal control problems based on these models, and finds a numerical solution in a reliable and efficient fashion. To obtain a high level of reliability and efficiency, the toolbox implements different homotopy methods for initial guess refinement. The first type of methods produces a feasible initial guess from an analytic initial guess based on user-provided parameters. The second type implements a warmstart procedure for parametric sweeps. We investigate the software performance in two different case studies. In the first case study we solve a single-aircraft reference problem for a large number of different initial guesses. The homotopy methods reduce the expected computation time by a factor of 1.7 and and the peak computation time by a factor of 8, compared to when no homotopy is applied. Overall, the CPU timings are competitive to timings reported in the literature. When the user initialization draws on expert a priori knowledge, homotopies do not increase expected performance, but the peak CPU time is still reduced by a factor of 5.5. In the second case study, a power curve for a dual-aircraft lift-mode AWE system is computed using the two different homotopy types for initial guess refinement. On average, the second homotopy type, which is tailored for parametric sweeps, outperforms the first type in terms of CPU time by a factor of 3. In conclusion, AWEbox provides an open-source implementation of efficient and reliable optimal control methods that both control experts and non-expert AWE developers can benefit from.

The extremely high rotation of some SMBHs is the origin of their relativistic rotational energy that results in their relativistic mass. Relativistic mass creates their relativistic gravity which is a partial answer to the missing dark matter.

Perovskite Solar Cell (PSC) is a third-generation photovoltaic device known for its rapid improvement in efficiency levels over the past decade. Moreover, the added benefits of abundant sourcing of raw materials, uncomplicated fabrication process, organic and inorganic device materials, and tuneable bandgaps make this technology a sustainable energy alternative. However, the efficiency values of these devices are subjected to variation depending on factors such as material compatibility, environmental conditions, energy band alignment of device components and stability characteristics to extrinsic and intrinsic factors. One such vital intrinsic factor is film morphology, homogenous and superior film quality formation and pinhole and trap-free films. In this study, we have investigated the formation of perovskite films on a qualitative basis using metal chloride washing of salts such as Erbium, Antimony, Cadmium and Chromium Chloride. The study aims to analyse the difference in film formation with various metal chloride washing and how this could potentially impact or contribute to photovoltaic performance if the devices are fabricated.