The financial equilibrium of the enterprise is an important company function ensuring by itself the maintenance of the enterprise of the competitive market. The financial equilibrium is analysed in numerous empirical studies. In this empirical study we highlight for the first time in a research the impact that taxation has on the financial equilibrium of some companies over ten years, period that includes the pre-crisis, the financial crisis and post-crisis periods.

This paper presents a piezoresistive pressure sensor with a shield layer for improved stability. Compared with the conventional piezoresistive pressure sensors, p-type piezoresistors are covered by an n-type shield layer, which is formed by ion implantation. The proposed pressure sensors have been successfully fabricated by bulk micromachining techniques. The impact of electrical field on piezoresistors is studied by simulation. The temperature drift of the pressure sensor has been investigated by both simulation and experimental measurement. Characteristics of developed pressure sensors are tested from -40 C to 125 C. A sensitivity of 0.022 mV/V/KPa and a maximum non-linearity of 0.085% FS are measured for the fabricated sensor in a pressure range of 1 MPa. The temperature coefficients of resistance of shielded piezoresistors are found to be smaller than those of un-shielded ones. It is demonstrated that the shield layer is able to reduce the drift caused by electrical field and ambient temperature variation.

The electrification of process industries is one of the main challenges when building a low-carbon society since they consume huge amounts of fossil fuel generating different emissions. Heat pumps are one of the instruments to perform industrial sector of carbon-neutral market players. This paper proposes an approach to improve the economic feasibility of heat pumps within the process plants. Initial energy targeting with Grand Composite Curves was used and supplemented with the detailed design of the evaporator and compressor for different condensation and evaporation pressures. The trade-off between the capital cost of the heat pump and the electricity cost was investigated and optimal configurations were selected. The case study investigates the gas fractioning unit of a polymer plant where three heat pumps were integrated into distillation columns. The results demonstrated that the heat recovery is 174 MW and requires an additional 37.9 MW of electricity to reduce hot utility by 212 MW. The selection of evaporation and condensation pressure of heat pumps allows saving of 21.5 M€/y for 7 years of plant operation.

The effects of anisotropic properties (wettability and roughness) on microgroove surfaces in pool boiling heat transfer using Novec-7100 as a working fluid were experimentally investigated. The idea of introducing the concept of anisotropic wettability in boiling experiments draws inspiration from biphilic surfaces. The investigation is also motivated by two-phase immersion cooling, which involves phase-change heat transfer by using dielectric liquid as a working fluid. Very few studies have focused on the effects of surfaces with anisotropic properties on boiling performance. Thus, this study aims to examine the pool boiling heat transfer performance on surfaces with microgroove-induced anisotropic properties under the saturation condition. A femtosecond laser–texturing method was employed to create microgroove surfaces with different groove spacing. The results indicated that anisotropic properties affected the heat transfer coefficient and critical heat flux. Relative to the plain surface, microgroove surfaces enhanced the heat transfer performance due to the increased number of bubble nucleation sites and higher bubble detachment frequency. An analysis of bubble dynamics under different surface conditions was conducted with the assistance of high-speed images. The microgroove surface with groove spacing of 100 μm maximally increased the BHTC by 37% compared to the plain surface. Finally, the CHF results derived from experiments were compared with related empirical correlations. Good agreement was achieved between the results and the prediction correlation.

Introduction: Heat is a kinetic process whereby energy flows from between two systems; hot-to-cold objects. In oro-dental implantology, conductive heat transfer/(or thermal stress) is a complex physical phenomenon to analyze and consider in treatment planning. Hence, ample research has attempted to measure heat-production to avoid over-heating during bone-cutting and -drilling for titanium (Ti) implant-site preparation and insertion, thereby preventing/minimizing early (as well as delayed) implant-related complications and failure. Objective: Given the low bone-thermal conductivity whereby heat generated by osteotomies is not effectively dissipated and tends to remain within the surrounding tissue (peri-implant), increasing the possibility of thermal-injury; this work attempts to obtain an exact analytical solution of the heat equation under exponential thermal-stress, modeling transient heat transfer and temperature changes in Ti implants upon hot-liquid intake. Materials and Methods: We investigate the impact of the material, the location point along implant length, and the exposure time of the thermal load on temperature changes. Results: Despite its simplicity, the presented solution contains all the physics and reproduces the key features obtained in previous numerical analyses studies. To the best of knowledge, this is the first introduction of the intrinsic time, a “proper” time that characterizes the geometry of the dental implant, where we show, mathematically and graphically, how the interplay between “proper” time and exposure time influences temperature changes in Ti implants, under the suitable initial and boundary conditions. Conclusions: This work aspires to accurately complement the overall clinical diagnostic and treatment plan for enhanced bone-implant interface, implant stability and success rates, whether for immediate or delayed loading strategies.

Electric heating and solid thermal storage system (EHSTSS) is widely used in district clean heating and the flexibility adjustment of combined heat and power (CHP) unit. It has been an effective way to absorb renewable energy. Aiming at the thermal design calculation and experimental verification of EHSTSS, the thermal calculation and the heat transfer characteristics of the EHSTSS are investigated in this paper. Firstly, a thermal calculation method for the EHSTSS is proposed in the paper. The calculation flow and calculation method for key parameters of heating system, heat storage system, heat exchange system and fan-circulating system in the EHSTSS are studied. Then, the instantaneous heat transfer characteristics of the thermal storage system (TSS) in the EHSTSS are analyzed, and the heat transfer process of ESS is simulated by FLUENT software. The uniform temperature distribution in the heat storage and release process of the TSS verifies the good heat transfer characteristics of the EHSTSS. Finally, EHSTSS test verification platform is built, and the historical operation data of the EHSTSS is analyzed. During the heating and release thermal process, the maximum temperature standard deviation of each temperature measurement point is 28.3℃ and 59℃respectively. The correctness of the thermal calculation of the EHSTSS is verified.

As the demand for liquefied petroleum gas (LPG) continues to increase worldwide, more LPG facilities are being constructed. However, the design and manufacture of pressure vessels used to store dangerous liquids or pressurised fluids, such as LPG, has been a major cause of hazards, including explosions and leakage. In this study, we aim to address this issue by designing and analysing a vertical pressure vessel with a capacity of 10 m3 of pressurised LPG in accordance with the American Society of Mechanical Engineers (ASME) code. Safety is the primary concern in designing pressure vessels due to the potential risks posed by accidents. Therefore, the main objective of this project is to design a pressure vessel that is safe from failure. The vessel is cylindrical with two elliptical heads, two nozzles, a manway and four leg supports, and we used Autodesk Inventor Professional 2023 for geometric modelling and Inventor Nastran for FEA analysis. To investigate the displacements, deflections and Von-Mises stresses in the pressure vessel, we used the finite element method, and Autodesk Inventor Nastran was employed for the analysis. Our results showed that changes to the structure of the pressure vessel were needed to reduce stress in the structure. Specifically, the displacement showed an inverse relationship with the tank section shell thickness. Moreover, we observed that the factor of safety increased linearly with shell thickness. We carefully considered permissible pressures and determined the required wall thickness to ensure acceptable maximum stresses. Our results indicate that the design is safe from failure, and the highest stresses are experienced by the manway followed by the shell, while the heads, nozzles and legs support experienced the lowest stresses. We also performed a theoretical calculation for the entire model and checked the results to ensure they were within the acceptable limits. In summary, our study highlights the importance of designing pressure vessels in accordance with ASME codes to ensure safety and prevent hazards caused by improper design and manufacturing. By using the finite element method, we identified potential stress points in the pressure vessel and were able to make modifications to improve its safety.

Precise association of serum leptin with body mass index (BMI) and blood pressure (BP; both systolic blood pressure (SBP) and diastolic blood pressure (DBP) is not well known for understanding their involvement in health and disease. Hence, the present study was planned to be conducted for investigating the association of BP, BMI and serum leptin levels in young normal weight (NW) and overweight (OW) male Saudi students. The NW (n: 198) and OW male subjects (n: 192) in the age range of 18-20 years were consulted. Blood pressure (BP) was measured with a mercury sphygmomanometer. Leptin Human ELISA Kits were employed for the determination of the serum leptin levels. The mean ± SD values of BMI (kg/m2), serum leptin (ng/ml), SBP (mmHg), and DBP (mmHg) all showed significant difference for young OW vs. NW male university students as: 27.52± 1.42 vs. 21.49± 2.03; 10.70± 4.67 vs. 4.68± 1.91; 121.37±2.59 vs.118.51±1.54 and 81.44±1.97 vs. 78.79±1.44 respectively. All associations (among BMI, leptin, SBP and DBP) showed positive linear and significant correlation except nonsignificant correlation of BMI and SBP for NW group. The present study in the young Saudi male students, presents significant variations for BP and serum leptin levels and significant positive linear association among serum leptin, BMI and BP.

High pressure crystallization technique has been successfully used to prepare an elusive form II of a non-steroidal anti-inflammatory drug, Mefenamic acid. Single crystal of form II was grown at 0.3 GPa from an 4:1 methanol/ ethanol mixture as a solvent using Diamond Anvil Cell. Comparison of crystal structures show that the efficient packing of MA molecules in Form II results from the structural flexibility of MA acid molecules. Compression studies performed on the single crystal of form I resulted in 14 % decrease of unit cell volume up to 2.5 GPa. No phase transition was observed up to this pressure. A reconstructive phase transition is required to induce conformational changes in the structure, which is confirmed by crystallization at high pressure results.

An experimental study is carried out in a cavitation tunnel on a propeller operating downstream of a non-uniform wake. The goal of this work is to establish quantitative correlations between the near pressure field and the cavitation pattern that takes place on the propeller blades. The pressure field is measured at the walls of the test section and in the near wake of the propeller, and is combined with quantitative high-speed image recording of the cavitation pattern. Through simple harmonic analysis of the pressure data and image processing techniques that allow to retrieve the cavitation extension and volume, we discuss the potential sources that generate the pressure fluctuations. Time correlations are unambiguously established between pressure peak fluctuations and cavitation collapse events, based upon the Rayleigh collapse time. Finally, we design a model to predict the cavitation-induced pressure fluctuations from the derivation of the cavitation volume acceleration. This simple model demonstrates a remarkable agreement with the actual pressure field.

The growing market penetration of heat pumps indicates the need for a performance test method which better reflects the dynamic behavior of heat pumps. In this contribution, we developed and implemented a dynamic test method for the evaluation of the seasonal performance of heat pumps by means of laboratory testing. Current standards force the heat pump control inactive by fixing the compressor speed. In contrast, during dynamic testing, the compressor runs unfixed while the heat pump is subjected to a temperature profile. The profile consists of the different outdoor temperatures of a typical heating season based on the average European climate and also includes temperature changes to reflect the dynamic behavior of the heat pump. The seasonal performance can be directly obtained from the measured heating energy and electricity consumption making subsequent data interpolation and recalculation with correction factors obsolete. The method delivers results with high precision and high reproducibility and could be an appropriate method for a fair rating of heat pumps.

The Double U-pipe ground heat exchanger, recognized for its straightforward process, cost-effectiveness, high heat exchange efficiency, and low thermal resistance, stands as the predominant ground heat exchanger type in today's shallow geothermal energy development and utilization. Recent years have seen significant research into the heat transfer influencing factors and heat exchange performance of Double U-pipe ground heat ex-changers via experimental testing methods. Yet, studies integrating numerical simulation with in-situ testing have been less frequent. Drawing on the cylindrical heat source model theory and the outcomes of regional in-situ thermal response tests, this paper develops a Double U-pipe ground heat transfer model by establishing physical, mathematical, and heat transfer geometric models. It assesses the impact of varying inlet temperatures, flow rates, and initial ground temperatures on heat exchange efficiency under heating conditions. The results validate the precision of the double U-pipe ground heat exchanger model based on in-situ testing. They show that enhancing the temperature differential between the inlet and initial temperatures, elevating the initial ground temperature, and moderately increasing the flow rate can boost the system's heat exchange efficiency.

The ability to control the temperature distribution T(t,r) and the rate of temperature change Rt,r inside glasses is important for their microstructuring. The lattice temperature is considered at time t, exceeding the electron-phonon thermalization time, and at a distance r from the center of the model spherical heating zone. In order to describe thermal excitations, the heat capacity of glasses must be considered as a function of time due to its long-term relaxation. A method for analytical calculation of T(t,r) and R(t,r) for glasses with dynamic heat capacity cdyn(t) is proposed. It is shown that during laser microstructuring the local cooling rate -R(t,r) significantly depends on the time dispersion of cdyn(t). It has been established that at the periphery of the model heating zone of the laser beam focus, the local cooling rate can reach more than 1011 K/s. Strong cooling rate gradients were found at the periphery of the heating zone, affecting the microstructure of the material. This effect is significantly enhanced by the time dispersion of cdyn(t). The effect associated with this time dispersion is significant even well above the glass transition temperature Tg, since even short relaxation times of the dynamic heat capacity cdyn(t) are significant.

With the development of energy internet, integrated energy system can effectively reduce carbon emissions and improve the utilization of renewable energy. In this paper, a low-carbon optimal scheduling model of integrated energy system considering heat loss of heat network pipeline is proposed. Based on the study of concentrating solar power (CSP) plant and heat storage tank (HS), an optimal scheduling model is established, which takes system operation cost, environmental pollution and penalty cost of abandoning wind and solar energy as objectives. Through the analysis of example results, it is proved that the model proposed in this paper can achieve the goal of reliable, low-carbon and economic operation of the system. At the same time, it shows that CSP unit can reduce the operation cost of system and increase energy coupling and utilization.

Urban areas are increasingly challenged by the urban heat island effect, resulting in increased energy consumption and reduced efficiency of conventional air source heat pumps (ASHPs). This study explores the integration of ground source heat pump (GSHP) systems with energy piles in urban environments, focusing on small to medium sized residential units. Energy piles combine structural support with geothermal heat exchange capabilities, taking advantage of stable ground temperatures to improve energy efficiency. The research examines key design considerations such as soil thermal properties, heat transfer mechanisms, and the optimal configuration of heat exchangers within the piles. Results indicate that GSHP systems can significantly reduce electricity consumption and operating costs compared to ASHPs, despite higher initial costs. Several factors, including site conditions, pile materials, and heat exchanger designs, are critical to system performance. The study concludes that while GSHP systems offer significant long-term benefits, their widespread adoption in Southeast Asia will require further development of construction methods and design strategies, as well as supportive government policies to mitigate initial costs. This work aims to advance the understanding and implementation of energy piles in urban environments, thereby promoting sustainable energy use in smart city development.

The object of this work is to determine the correlation on the Nusselt number on the individual rows of a four-row tubular finned heat exchanger with continuous fins with a staggered tube arrangement using CFD modelling. Correlations for calculating Darcy-Weisbach friction factors on individual tube rows were also determined. Relationships for the Nusselt number and friction factor derived for the entire exchanger based on CFD modelling were compared with those available in the literature determined using experimental data. The maximum relative differences between the Nusselt number for a four-row exchanger determined experimentally and by CFD modelling are in the range from 22% for a Reynolds number based on a tube's outside diameter of 1,000 to 30% for a Reynolds number of 13,000. The maximum relative differences between the friction factor for a four-row exchanger determined experimentally and by CFD modelling are in the range of 50% for a Reynolds number based on a tube outer diameter of 1,000 to 10% for a Reynolds number of 13,000. The CFD modeling performed shows that in the range of Reynolds numbers based on hydraulic diameters from 150 to 1,400, the Nusselt number for the first row in a four-row finned heat exchanger is about 22% to 15% higher than the average Nusselt number for the entire exchanger. In the range of Reynolds number changes based on hydraulic diameter from 2,800 to 6,000, the Nusselt numbers on the first and second rows of tubes are close to each other. Correlations on Nusselt numbers and friction factors derived for individual tube rows can be used in the design of plate-fin and tube heat exchangers used in equipment such as air-source heat pumps, automotive radiators, air-conditioning systems and in air hot-liquid coolers. In particular, the correlations can be used to select the optimum number of tube rows in the exchanger.

Within the research of pressure pipeline inspection methods there is an industry that is constantly growing and becoming more efficient. The purpose of inspection methods on pressure pipelines comes back to the issue of resolving leaks, corrosion, and inability of a pipeline to function (eventually). Evidently, these issues can hurt the environment, the public using the material being carried out by these pressure pipelines such as natural gas or petroleum and can hurt the pockets of pipeline companies that did not react quick enough to their pipeline solely for the reason that they may have not noticed there was an issue with their pressure pipeline. In-line inspection methods are continuously growing and have already made an impact to prevent the catastrophes that occur when a pipeline is not maintained. Technology such as smart pigs, MFLs, and ultrasounds are the future of pressure pipeline inspection. This research paper explains their pros and cons and how they’re overall more efficient and preferred as the primary inspection method for a pipeline. Older, more traditional methods such as aerial inspection, by-foot inspection, hydrostatic pressure testing, and Direct Assessment does not cover every base of inspection like in-line inspection technology does and this research explains why that is and the areas of where in-line inspection technology can be improved and deemed not as useful. This is where trenchless renewal and replacement methods come into play with inspection methods and determining the characteristics of a pipeline that matches with which inspection method and which trenchless method to use. The future of inspection methods for pressure pipelines is attainable and is somewhat already here, this research discusses the new emerging technologies and how designing in-line inspection technology to be cheaper and more versatile with pipeline characteristics can make everyone a winner in the future. A winner as far the environment being safe, neighborhoods near pressure pipelines being safe, companies being able to install in-line inspection technology at a fraction of the cost of today and the efficiency of pipelines by monitoring the characteristics with this new technology.

Abstract: Flexible pressure sensors are electronic devices that can be attached to various irregular surfaces to measure the pressure. It is widely used in wearable devices and for health detection. In this study, a general carbon nanotubes/polydimethylsiloxane (CNTs/PDMS) sponge electrode was fabricated as the elementary component of the compressible system. The sensitivity of the flexible pressure sensor is improved by optimizing the preparation process of the conductive sponge and surface modification of the CNTs, and the highest sensitivity reached 71.831 kPa-1(0~2 kPa). The flexible pressure sensor can be used to detect subtle pressure quickly and accurately so that it can be used as wearable sensor to measure the radial artery wave of a human body, which has potential applications in health care and other fields.

Abstract: The promotion and development of healthy cities are vital for enhancing human habitats and fostering sustainable economic growth. Based on the core database of Web of Science and the knowledge graph software, this paper makes a quantitative analysis of the literature related to attention recovery abroad. It is found that in recent years, the research on attention recovery has developed rapidly, the number of related literature has been increasing, and the research content presents the characteristics of interdisciplinary integration. By further analyzing the characteristics of research literature, research context, and knowledge basis, this paper summarizes the empirical research based on the existing quantitative analysis, reviews the research field based on the mechanism of attention recovery, and analyzes the development process and trend based on the research basis of attention recovery. Due to the change of modern life style, human health problems are becoming more and more prominent. Attention restoration design provides a new research idea and method to balance the relationship between humans and the urban environment.

Abstract:High-pressure water jet technology has received extensive attention and application due to its high efficiency and environmental protection characteristics. The high-pressure water jet nozzle is its core component, and the research on the high-pressure water jet nozzle is conducive to improving the jet performance and improving the jet efficiency. This paper introduces the characteristics of water jet and the working principle of pure water jet, abrasive water jet, pulsed water jet and cavitation water jet, reviews the theoretical analysis and experiment of the predecessor's nozzle, briefly explains the application of high-pressure water jet and looks forward to the development trend of this technology.

Abstract Several studies have been conducted to strengthen weak road layers, regardless of whether they are un-der construction or are undergoing maintenance. Using substrates filled with different materials has proven effective for increasing the strength of these layers. In this study, I evaluated the coefficient of lateral soil pressure under various conditions when using reinforced and unreinforced piles filled with in-expensive material and the extent of their contribution to strengthening road layers. The results con-firmed that there was a difference in the coefficient of lateral soil pressure when the sand-filled piles were reinforced. The sand-filled piles were divided into several parts by arming. The maximum coeffi-cient of lateral soil pressure was 0.38 in the case of sand (1 mm) with reinforcement, whereas it was 0.29 in the same case without reinforcement as shown in Figure 1. The maximum coefficient of lateral soil pressure was 0.27 in the case of granite grain (2 mm) with reinforcement, whereas it was 0.17 in the same case without reinforcement. Moreover, the maximum lateral pressure coefficient was 0.26 in the case of granite grain (3 mm) with reinforcement, and it was 0.30 in the same case without reinforce-ment.

Compressed gas storage of hydrogen has emerged as the preferred choice for fuel cell vehicle man- ufacturers, as well as for various applications like road transport, and aviation. However, designers face increasing challenges in designing safe and efficient composite overwrapped pressure vessels (COPVs) for hydrogen storage. One challenge lies in the development of precise software that con- sider a multitude of factors associated with the filament winding process. These factors include layer thickness, stacking sequence, and the development of particularly robust models for the dome region. Another challenge is the formulation of predictive behavior and failure models to ensure that COPVs have optimal structural integrity. The present study offers an exploration of numerical methods used in modeling COPVs, aiming to enhance our understanding of their performance characteristics. The methods examined include finite element analysis in Abaqus, involving conventional shell elements, continuum shell elements, three-dimensional solid elements, and specialized homogenization tech- niques for multilayered composite pressure vessels. Through rigorous comparisons with type-III pressure vessels from the literature, the research highlights the most suitable choice for simulating COPVs and their practicality. Finally, we propose a new design for type-IV hydrogen composite pressure vessels using one explored method, paving the way for future developments in this critical field.

The well-known equations for the process of powder compaction (PCP) in a rigid die published over the period from the beginning of the last century to the present are considered. Most of the considered equations are converted into the dependence of the densification pressure on the relative density. The equations were analyzed and their ability to describe PCP was assessed by determining the coefficient of determination when approximating experimental data on the compaction of various powders. It is shown that most of the equations contain two constants, the values of which are determined by fitting the mathematical dependence to the experimental curve. Such equations are able to describe PCP with high accuracy in the case of compaction of powders up to a relative density of 0.9-0.95. It is also shown that different equations can describe PCP in the range of density change from the initial to 0.9 with the same and sufficiently high accuracy, but when the process of compaction is extrapolated to higher values of density, the curves diverge. This indicates the importance of equations that can unambiguously describe PCP to a relative density equal to or close to 1.0. For an adequate description of PCP to a relative density greater than 0.95, equations containing three or four constants have proven themselves well.

Ischemia, the inadequate blood flow, can arise from pre-existing or traumatic events, remain an undetectable issue, and impact the body's ability to provide oxygen to necessary limbs, organs, muscles, or tissue. New technology involving wearable ultrasonic devices allows medical professionals to gain real-time insight into the cardiovascular system of their patients. A non-invasive, postage-stamp-sized ultrasonic sensor can be attached to a patient, allowing for continuous monitoring of the patient’s blood pressure outside of the hospital. After reviewing 16 papers on ultrasonic sensors, this paper intends to review the current use of wearable ultrasonic sensors and the advantages and limitations of the technology used to obtain accurate blood pressure readings. This review will bring attention to the evolving and expanding world of wearable ultrasonic sensors for medical applications.

This research aims to investigate the effects of parental pressure on students' academic achievement at the school level. The research objectives include examining the relationship between parental pressure and academic achievement and identifying potential moderating variables. A sample of middle and high school students will be utilized in this study.

Background: The mental state is important in the health/illness process. Including stress, depression and anxiety. Nature immersion therapies have been implemented as a valid method for reducing these disorders. The aim will evaluate the effect of forest intervention therapies on levels of stress, depression, and anxiety. Methods: We searched for randomized clinical trials related to stress, anxiety and depression levels. Risk of bias was assessed according to the guidelines of the Cochrane Handbook for International Systematic Reviews. Results: We identified and synthesized eight publications. Two studies for cortisol showed significant differences between the pre-test and post-test levels in the intervention groups. One study including Natural killer cells, that reported a significant decrease in the intervention group compared to the control group. Two studies used the Stress Response Inventory, indicated a significant reduction in stress levels in the intervention group compared to the control group. Regarding Restorative Out-come Scale, no significant differences were found. Three studies were selected for the evaluation of anxiety and depression levels according to the Positive and Negative Affect Schedule. Four studies used The Profile of Mood States scale; no significant difference was observed. Conclusions: There is limited evidence to recommend forest bathing for reducing these disorders.

Intra-abdominal pressure (IAP) elevation during capnoperitoneum can cause adverse cardiovascular and respiratory effects. This study aimed to determine if a sequentially increased IAP affects cardiovascular and respiratory variables in anesthetized dogs and evaluate the effects of constant rate infusion of dexmedetomidine (Dex) on cardiovascular and respiratory variables with increased IAP. Five dogs were anesthetized, instrumented, and the Veress needle was equipped to adjust the IAP using a carbonic anhydrase insufflator. Stabilization was conducted for 1 h, and physiological variables were measured in IAPs of 0, 5, 10, 15, and 20 mmHg and after desufflation. After the washout period, the dogs underwent similar procedures along with constant rate infusion of dexmedetomidine. Cardiovascular effects of increased IAP up to 20 mmHg were not significant in healthy beagle dogs and those administered with dexmedetomidine. In the control group, the arterial pressure slightly increased, but not statistically significant, at an IAP of 20 mmHg compared with that at baseline (mean arterial blood pressure, p = 0.399; systolic arterial blood pressure, p = 0.293; diastolic arterial blood pressure, p = 0.141). When comparing the control and dexmedetomidine groups, overall significant effects of dexmedetomidine were noted on heart rate, cardiac output, and systemic vascular resistance during the experiment. Respiratory effects were not affected by abdominal insufflation when compared between different IAPs and between the two groups. Overall, an increased IAP of until 20 mmHg did not significantly affect cardiovascular and respiratory variables in both control and dexmedetomidine groups. This study suggests that dexmedetomidine infusion administration is applicable in laparoscopic procedures in healthy dogs.

Background: Due to the importance of brain death (BD) diagnostic do not mistake, reliable confirmatory exams should be performed to enhance its security. This study aims to evaluate the intracranial pressure (ICP) pulse morphology behavior in brain-dead patients through a noninvasive monitoring system. Methods: A pilot case-control study was conducted in adults that met the BD national protocol criteria. Quantitative data from the ICP waveforms were extracted and analyzed comparing BD patients and health subjects. Results: Fifteen patients were included. ICP waveforms presented substantial differences amidst BD patients when compared to the control group. Moreover, pulse amplitude and time to peak variables values in the case group were also statistically significant. Conclusions: In this exploratory study, noninvasive ICP waveforms have shown potential as a screening method in patients with suspected brain death. Future studies should be carried out in a larger population.

Background: Hypertension is a condition of a person's blood pressure being at a level above normal, hypertension treatment can be done herbally using avocado leaves. Avocado leaves can lower blood pressure because they contain active substances, namely flavonoids and quercetin. This research was conducted in the working area of the Tilango Health Center. Objective: This study aims to determine the effect of giving boiled water of avocado leaves on reducing blood pressure in the elderly with hypertension. Methods: Design This study used a two-group quasi-experimental pre-test - post-test design. The sample is the elderly who have hypertension, amounting to 125 people with purposive sampling technique. The research instrument used a questionnaire. Results: Statistical test using T-Test on blood pressure before and after the intervention was given a significance value of 0.000 (p-value < 0.05 ). Conclusion : This study concludes that there is a significant effect between giving avocado leaf boiled water on reducing blood pressure in the elderly with hypertension in the working area of the Tilango Health Center.

Background: At altitudes beyond 2500 m the risk of developing high altitude pulmonary edema (HAPE) grows with the increases in pulmonary arterial pressure. HAPE is characterized by severe pulmonary hypertension, though the incidence and relevance of individual risk factors are not yet predictable. However, the systolic pulmonary pressure (SPAP) and peak in tricuspid regurgitation velocity (TVR) are crucial factors when diagnosing pulmonary hypertension by echocardiography. Methods: The SPAP and TVR of 27 trekkers aged 20-65 years en route in the Solu Khumbu region of Nepal was assessed. Echocardiograph measurements were performed at Lukla (2,860 m), Gorak Shep (5170 m), and the summit of Kala Patthar (5,675 m). The altitude profile and the participant’s characteristics were also compiled for correlation with the measured data. Results: The results showed a highly significant increase of SPAP and TVR after ascending Kala Patthar. The study revealed a lower increase of SPAP and TVR in the group of older participants, although the initial respective measurements in Gorak Shep were significantly higher for this group. A similar finding occurred in those using Diamox® as prophylaxis. There was an inverse relationship between TVR and SPAP, the peripheral capillary oxygen saturation and heart rate. Conclusions: The echocardiograph results indicate that older people are a risk group for developing a HAPE. The prophylactic use of acetazolamid led to higher initial SPAP values in Gorak Shep, and a lower increase of SPAP as well as TRV after ascending Kala Patthar. Arterial oxygen saturation measurements can provide an indicator for the self-assessment for the risk of developing HAPE and provide a rule of thumb for the altitude profile but does not replace a HAPE diagnosis. The collected data variables concerning backpack weight, sex, workload (actual ascent speed), and pre-existing diseases were not statistically significant factors related to SPAP and TVR (p=<0.05).

The formation of rock fractures in nature has a certain relationship with water seepage. In order to analyze the shape of rock fracture, we propose a rock deformation theoretical model in three-dimensional space considering with the condition of seepage water pressure, and establish the mass conservation equation, seepage equation, surrounding rock displacement equation, so as to deduce the rock deformation control equation under seepage pressure action. The numerical analysis of the nonlinear quadratic partial differential equation obtains the fracture deformation distribution in the example, and verifies with the calculated fracture morphology. And we further use this principle to analyze the fracture morphology in nature and prove the rationality of the theory.

Purpose: The evaluation of the efficacy of topical hypotensive treatment and/or systemic corticosteroids therapy in patients with elevated intraocular pressure and Graves’ orbitopathy (GO). Methods: 172 eyes in 86 individuals with duration of GO ≥ 3 months, intraocular pressure in either eye ≥ 25.0 mmHg and GO ranked ≥ 3 at least in one eye in modified CAS form, were included. The study subjects were divided into three treatment subgroups: subgroup I was administered latanoprost QD; subgroup II was administered a combined preparation of brimonidine and timolol BID; subgroup III was the control group, not receiving any topical hypotensive treatment. All the study participants received systemic treatment – intravenous corticosteroid therapy at the same dose, according to the EUGOGO guideline Results: On the final visit, the mean IOP value was significantly lower in all treatment subgroups comparing to the initial values. In both subgroups receiving topical treatment the IOP reduction was higher than in the control group receiving systemic corticosteroids only. However, the latanoprost eye drops decreased intraocular pressure more effectively than drops containing brimonidine and timolol. Conclusion: Topical ocular hypotensive treatment is effective in reducing intraocular pressure in GO and decreases intraocular pressure more effectively than systemic corticosteroid therapy alone.

While visual assessment is the standard technique for burn evaluation, computer-aided diagnosis is increasingly sought due to high number of incidences globally. Patients are increasingly facing challenges which are not limited to shortage of experienced clinicians, lack of accessibility to healthcare facilities, and high diagnostic cost. Certain number of studies were proposed in discriminating burn and healthy skin using machine learning leaving a huge and important gap unaddressed; whether burns and related skin injuries can be effectively discriminated using machine learning techniques. Therefore, we specifically use pre-trained deep learning models due to deficient dataset to train a new model from scratch. Experiments were extensively conducted using three state-of-the-art pre-trained deep learning models that includes ResNet50, ResNet101 and ResNet152 for image patterns extraction via two transfer learning strategies: fine-tuning approach where dense and classification layers were modified and trained with features extracted by base layers, and in the second approach support vector machine (SVM) was used to replace top-layers of the pre-trained models, trained using off-the-shelf features from the base layers. Our proposed approach records near perfect classification accuracy of approximately 99.9%.

Several common and functional genes are known to contribute to responsiveness to blood pressure (BP) therapy. BP therapy is typically guided by algorithms that do not include a patient’s genetic information. This study aimed to determine the impact of a multi-organ genetic panel on BP response to pharmacotherapy. Eighty-six patients completed one study visit consisting of a buccal swab collection, measurement of office BP, and a medical chart review for BP history. Genes analyzed included those that encode for one drug metabolizing enzyme, renal Na+ handling, vascular, and cardiac function. Relationships between genotype and control of BP (<140/<90), ∆ systolic BP, ∆ diastolic BP, and ∆ mean arterial BP were assessed. SLC12A3 resulted in a significant association between the target drug and the functional genotype for BP control (<140/<90 cut off) (p<0.05). Conversely, three of five renal genotypes were associated with BP control using 120/80 as a cut-off (p<0.05). Three of four cardiac genotypes were associated with the BP control at <140/<90, with one being statistically significant (position 49 of ADRB1). Only one vascular genotype was predictive of blood pressure control at <140/<90. We found a significant drop in mean BP from baseline in six genes, three important in the diuretic response and three in β-blockade (p<0.05 on target drug vs. not). These results demonstrate that a multi-gene panel for renal Na+ handling, vascular function, and cardiac output may influence the BP response to therapy, but larger studies with more statistical power are needed.

We previously reported how the loss of CHIP expression (Carboxyl terminus of Hsc70-Interacting Protein) during pressure overload resulted in robust cardiac dysfunction, accompanied by a failure to maintain ATP levels in the face of increased energy demand. In this study, we analyzed the cardiac metabolome after seven days of pressure overload and found an increase in long- and medium-chain fatty acid metabolites in wild-type hearts, a response that was attenuated in mice that lack expression of CHIP (CHIP^-/-). These findings suggest that CHIP may play an essential role in regulating oxidative metabolism, pathways that are regulated in part by the nuclear receptor PPARα (Peroxisome Proliferator-Activated Receptor alpha). Next, we challenged CHIP^-/- mice with the PPARα agonist, fenofibrate. Surprisingly, treating CHIP^-/- mice with fenofibrate for five weeks under non-pressure overload conditions resulted in a loss of skeletal muscle mass and a marked increase in cardiac fibrosis, accompanied by a decrease in cardiac function. Isolated CHIP^-/- cardiac fibroblasts treated with fenofibrate did not increase synthesis of collagen or TGFβ, suggesting that the fibrosis observed in CHIP^-/- hearts likely depends on signaling from other cell types or circulating factors. In conclusion, in the absence of functional CHIP expression, fenofibrate results in unexpected cardiac pathologies. These findings are particularly relevant to patients harboring loss-of-function mutations in CHIP and are consistent with a prominent role for CHIP in regulating cardiac metabolism.

We evaluated the association of blood pressure with blood levels of cadmium, lead, and cadmium and lead together (cadmium+lead) in a representative sample of adolescents from Korea by use of 2010-2016 data from the Korean National Health and Nutrition Examination Survey (KNHANES). This cross-sectional study enrolled adolescents aged at 10-18 years-old who completed a health examination survey and had blood measurements of lead and cadmium. The association of adjusted mean differences in diastolic and systolic blood pressure with doubling of blood lead and cadmium were estimated by regression of blood pressure against log₂-transformed blood metals and their quartiles after covariate adjustment. Adjusted odds ratios for prehypertension were calculated for log₂-transformed blood levels of lead and cadmium and their quartiles. Our analysis of adolescents in Korea indicated that blood levels of lead and cadmium were not significantly associated with increased blood pressure or risk of pre-hypertension. However, the cadmium+lead level was associated with pre-hypertension. Previous studies showed that blood levels of lead and cadmium were associated with increased blood pressure and risk of hypertension in adult populations. We found no such effect in Korean adolescents, although the cadmium+lead level was associated with prehypertension. These differences may be because adolescents generally have lower levels of these blood metals or because adolescents only rarely have hypertension.

As the demand of heating and air conditioning is increasing day by day due to getting a comfortable life, for that reason, the market for heat pump and air conditioning systems or both, is seeing a steady increase in low global warming potential. All researchers on heat pump and air conditioning systems are searching for environmentally friendly refrigerants. However, a significant number of contemporary refrigerants (HCFCs) have the potential to cause global warming and ozone depletion, such as those found in heat pump air conditioning systems. Using more environmentally friendly refrigerants, including hydrocarbon and blend refrigerant mixtures, is one way to lower GWP and Ozone depletion potential. This study examines the performance of several alternative refrigerants, including R32, R134A, R410A, R22, and R290. In order to examine the performance of R290, theoretical and simulation results are compared on various refrigerants while taking into account a number of performance parameters, including the refrigerant energy efficiency ratio, mass flow rate, coefficient of performance, cooling capacity, and compressor work for one ton of refrigeration (1TR) air conditioners. One player with a very low GWP is R290. However, the only drawback is that it can catch fire and is hazardous to use in split-type commercial heat pump air conditioning applications. The environmental and thermo physical properties of HC-290 are significantly better than those of other materials, according to theoretical and simulation studies utilizing Cool Pack software, hence it is a viable replacement.

This paper investigates a numerical code coupling technique to tackle multi-physics and multi-scale simulations using state-of-the-art software packages that typically address some specific modeling domain. The coupling considers the in-house FEM code, FEMuS, and the FVM code OpenFOAM, by exploiting the MED library from the SALOME platform. The present approach is tested on a buoyancy-driven fluid flow within a square cavity, where the buoyancy force constitutes the coupling term. In uncoupled scenarios, momentum and temperature equations are solved both in FEM and FVM codes without data exchange. In the coupled setting, only the OpenFOAM velocity and the FEMuS temperature fields are solved separately and shared at each time step (or vice versa). The MED library handles the coupling with the addition of suitable ad-hoc data structures that perform the field transfer between codes. Different Rayleigh numbers are investigated, comparing the outcomes of coupled and uncoupled cases with reference literature results. Additionally, a boundary data transfer application is presented to extend the capabilities of the coupling algorithm to coupled applications with separate domains. In this problem, the two domains share interfaces and boundary values on specific fields as fluxes are exchanged between the two numerical codes.

Heat stress results in significant economic losses to the poultry industry. Genetics plays an important role in chickens adapting to the warming environment. Physiological parameters, including hematochemical parameters, change in response to heat stress in chickens. To explore the genetics of heat stress resilience in chickens, a genome-wide association study (GWAS) was conducted using Hy-Line Brown (HLB) layer chicks treated with either high ambient temperature or combined high temperature and Newcastle disease virus (NDV) infection. Hematochemical parameters were measured during three treatment phases: acute heat stress, chronic heat stress, and chronic heat stress combined with NDV infection. Significant changes in blood parameters were recorded for 11 parameters across the three treatments. The GWAS revealed 39 significant SNPs (P < 0.05) for 7 parameters, located on Gallus gallus chromosomes (GGA) 1, 3, 4, 6, 11, and 12. The significant genomic regions were further investigated to examine if the genes within the regions were associated with the corresponding traits under heat stress. A candidate gene list including genes in the identified genomic regions that were also differentially expressed in chicken tissues under heat stress was generated. Understanding the correlation between genetic variants and resilience to heat stress is an important step in improving heat tolerance in poultry.

Hay and straw are commonly used materials in agriculture. They are organic materials and therefore flammable. This article examines the behaviour of hay and straw when exposed to radiant heat. The objective of this study is to experimentally determine the ignition temperature of hay and straw under the influence of radiant heat. The research investigates the effects of sample type (hay and straw) and sample quantity on the thermal degradation process, temperature increase within the samples, and ignition temperature of the samples as a function of time. The ignition temperature of hay was determined to be higher (407°C) compared to straw (380°C). The results did not demonstrate a significant correlation between sample type and the thermal degradation process or the ignition temperature of hay and straw.

Anode bonding is a widely used method for fabricating devices with suspended structures, and this approach is often combined with deep reactive ion etching (DRIE) for releasing the device. However, the DRIE process with a glass substrate can potentially cause two critical issues: heat accumulation on the suspended surface and charging effects resulting from the reflection of charged particles from the glass substrate. In particular, for torsional bars with narrow width, the heat accumulated on the suspended surface may not dissipate efficiently, leading to photoresist burning and subsequently resulting in the fracture of the torsional bars. Moreover, once etching is finished through the silicon diaphragm, the glass surface becomes charged, and incoming ions are reflected towards the back of the silicon, resulting in the etching of the back surface. To address these issues, we proposed a method of growing silicon oxide on the back of the device layer. By designing, simulating, and fabricating electrostatic torsional micromirrors with common cavity silicon-on-glass (SOG) structures, we successfully validated the feasibility of this approach. This approach ensures effective heat dissipation on the suspended surface, even when the structure is over-etched for an extended period, and enables the complete etching of torsional bars without adverse effects due to the overheating problem. Additionally, the oxide layer can block ions from reaching the glass surface, thus avoiding the charging effect commonly observed in SOG structures during DRIE.

Space shuttle has been a hall mark of American space program since its inception. Despite its temporary shutdown few years ago, with the recent interest in space exploration which includes revitalizing human outpost in microgravity and transportation required to build it, realize other experiments (e.g. in space telescopes, in space manufacturing) and interplanetary voyages, it has regained attention. Its superior design, manufacturing, materials, performance, durability, and efficiency place it among the best, in fact, the only effort by mankind to build a reusable craft horizontally, launch vertically like a rocket and fly back like a plane. Various requirements emerge during its design (thermal, fluid, acoustics, vibration and structural) and design of its main engine (Aerojet Rocketdyne RS 25) which requires considerable attention, heat transfer being most important. This facilitated and necessitated use of various types of heat exchangers such as single coil, heat pipe, built in internal heat exchanger (IHEX), external heat exchanger (EHEX), condensing heat exchanger (CHEX), Interface heat exchangers (InHEX), regenerative heat exchanger (RHEX) and compact heat exchangers (CoHEX), change, manipulate and optimize their configurations in piping and instrumentation diagrams (PIDs). In this short narrative, an effort has been made to summarize them, and their developments over time with a focus on the application, design, manufacturing, materials, and performance (in service and final operation).

The purpose of this study is to check out the involvement of entropy in Mpemba effect. Provided that preheating of the water the cooling duration is reduced, we theoretically show that water gains more entropy when warmed and re-cooled to the original temperature.

Fermenter is a vessel that maintains optimum environment for the development of significant microorganism used in large scale fermentation process and the commercial production of products like Alcoholic beverages, Enzymes, Antibiotics, Organic acids etc. The fermenter aims to produce biological product like vaccines and hormones, it is necessary to monitor and control the different parameters like external and internal mass transfer, heat transfer, fluid velocity, shear stress, agitation speed, aeration rate, cooling rate or heating intensity, and the feeding rate, nutrients, base or acid valve. Fermentation in the fermenter are accomplished in several configuration and these simple configurations are batch, fed-batch and continuous fermentation process. Fermentation process is carried out in small or large size fermenter depending on product quantity. The selection of the suitable process depends on the fermentation kinetics, type of microorganism used and process economic aspects. Improved modelling tools, reactor operation and reactor design in bioreactor is because of mass transfer behavior and it is important for reaction rate maximizing, throughput rates optimization and cost minimizing. The fermenter design, fermentation process, types of the fermenter that are used in industries and heat and mass transfer in fermenter is discussed.

In this study, we evaluated the cold drawing workability of two kinds of modified 9Cr-2W steel containing different contents of boron and nitrogen, depending on the temperature and time of normalizing and tempering treatments. Using ring compression tests at room temperature, the effect of intermediate heat treatment condition on workability was investigated. It was found that the prior austenite grain size can be changed by the austenite transformation, and the grain size increases with increasing temperature during normalizing heat treatment. Alloy B and Alloy N showed different patterns after normalizing heat treatment. Alloy N had higher stress than Alloy B, and the reduction in alloy N increased, while the reduction in alloy B decreased. Alloy B showed a larger number of initially formed cracks and a larger average crack length than Alloy N. Crack length and number increased proportionally in Alloy B as the stress increased. Alloy B had lower crack resistance than Alloy N due to boron segregation.

In the present paper, laminar forced convection nanofluid flows in a uniformly heated horizontal tube were revisited by direct numerical simulations. Single and two-phase models were employed with constant and temperature-dependent properties. Comparisons with experimental data showed that the mixture model performs better than the single-phase model in the all cases studied. Temperature-dependent fluid properties also resulted in a better prediction of the thermal field. A particular attention was paid to the grid arrangement. The two-phase model was used then confidently to investigate the influence of the nanoparticle size on the heat and fluid flow with a particular emphasis on the sedimentation process. Four nanoparticle diameters were considered: 10, 42, 100 and 200 nm for both copper-water and alumina/water nanofluids. For the largest diameter dnp = 200 nm, the Cu nanoparticles were more sedimented by around 80 %, while the Al₂O₃ nanoparticles sedimented only by 2.5 %. Besides, it was found that increasing the Reynolds number improved the heat transfer rate, while it decreased the friction factor allowing the nanoparticles to stay more dispersed in the base fluid. The effect of nanoparticle type on the heat transfer coefficient was also investigated for six different water-based nanofluids. Results showed that the Cu-water nanofluid achieved the highest heat transfer coefficient, followed by C, Al₂O₃, CuO, TiO₂, and SiO₂, respectively. All results were presented and discussed for four different values of the concentration in nanoparticles, namely φ = 0, 0.6, 1 and 1.6%. Empirical correlations for the friction coefficient and the average Nusselt number were also provided summarizing all the presented results.

As shown in former papers, the nonadiabatic Heisenberg model presents a novel mechanism of Cooper pair formation generated by the strongly correlated atomic-like motion of the electrons in narrow, roughly half-filled "superconducting bands". These are energy bands represented by optimally localized spin-dependent Wannier functions adapted to the symmetry of the material under consideration. The formation of Cooper pairs is not the result of an attractive electron-electron interaction but can be described in terms of quantum mechanical constraining forces constraining the electrons to form Cooper pairs. There is theoretical and experimental evidence that only this nonadiabatic mechanism operating in superconducting bands may produce eigenstates in which the electrons form Cooper pairs. These constraining forces stabilize the Cooper pairs in any superconductor, whether conventional or unconventional. Here we report evidence that also the experimentally found superconducting state in bismuth at ambient as well as at high pressure is connected with a narrow, roughly half-filled superconducting band in the respective band structure. This observation corroborates once more the significance of constraining forces in the theory of superconductivity.

A sintered wick was formed in a heat pipe through the process of sintering a mixture of copper powder with particle sizes of 100㎛ and 200㎛, mixed with a pore-forming agent. On application to the heat pipes. The thermal resistance of heat pipes containing a sintered wick was calculated for different tilting angles (0°, 45°, and 90°) according to the type of powder, thickness of the sintered wick, and the filling ratio of the working fluid. The heat transfer efficiencies were evaluated through temperature tests. The capillary force, which is closely related to heat transfer efficiency, is determined by the effective pore radius resulting from the sintering of the copper powder. Furthermore, it was observed that the heat transfer performance of the heat pipe was at its best when the working fluid filling ratio was 30%. Additionally, the width of the wick was found to have a direct correlation with the heat transfer performance.

Finnish government's carbon neutrality goal by 2035 requires integration of renewable energy sources into the power grid. Considering the stochasticity of these resources, additional sources of flexibility are necessary to balance supply and demand in the power grid. District heating network (DHN) operators in Finland plan to shut down fossil-fuel-based combined heat and power plants and electrify heating systems by deploying heat pumps (HPs) and electric boilers. Techno-economic analysis and optimal operation of DHN-connected HPs and electric boilers in providing ancillary balancing services considering the 15-minute granularity in the balancing markets in Finland were investigated. The objective was to maximize the potential revenue for DHN operators gained from the day-ahead electricity market and frequency containment reserve (FCR) balancing markets. Three inter-connected DHNs in the Helsinki metropolitan area were optimized considering the reference year 2019 and each operator's decarbonization strategies for 2025. HPs could gain the highest profit from FCR-D up-regulation market, while the electric boiler may gain considerable profits from FCR-D down-regulation market. Compared to other balancing markets studied, the FCR-N market had a limited profit margin. Sensitivity analysis indicated that spot electricity prices and CO2 emission allowance prices have a significant impact on the profit from balancing markets.

Aluminium bronzes possess a unique combination of high strength and wear and corrosion resistance in aggressive environments; thus, these alloys find wide application in marine, shipbuilding, aviation, railway, offshore platform applications and other fields. Iron-aluminium bronzes (IABs) are the cheapest and most widely used. When the aluminium content is above 9.4 wt%, IAB is biphasic (i.e. it undergoes -transformation) and can be subjected to all heat-treatment types depending on the desired operating behaviour of the bronze component. This article presents correlations (mathematical models) between the primary mechanical characteristics (yield limit, tensile strength, elongation, hardness and impact toughness) and the ageing temperature and time of quench at 920°C in water Cu-11Al-6Fe bronze, obtained using the centrifugal casting method. The microstructure evolution was evaluated depending on the ageing temperature and time changes. Overall, the research was conducted in three successive inter-related stages: a one-factor-at-a-time study, planned experiment, and optimisations. Four optimisation tasks, which have the greatest importance for practice, were formulated and solved. The defined multiobjective optimisation tasks were solved by searching for the Pareto-optimal solution approach. The decisions were made through a nondominated sorting genetic algorithm (NSGA-II) using QstatLab. The optimisation results were verified experimentally. Additional samples were made for this purpose, quenched at 920°C in water and subjected to subsequent ageing with the optimal values of the governing factors (ageing temperature and time) for the corresponding optimisation task. The comparison of the results for the mechanical characteristics with the theoretical optimisation results presents good agreement.

The performance of ground heat exchangers systems depends on the knowledge of the thermal parameters of the ground like thermal conductivity, thermal capacity and diffusivity. The knowledge of these parameters often requires quite accurate experimental analysis, known under the name of Thermal Response Test (TRT). In this paper, after a general analysis of the various available types of TRT and the study of the theoretical basics of the method, the perspective of the definition of a simplified routine method of analysis based on the combination of a particular version of TRT and the routine geotechnical tests for the characterization of soil stratigraphy and of the ground characteristics, mandatory before the construction of a new buildings, even if limited to quite short drilling depth (lower than 30 m). The idea of developing TRT in connection with geotechnical test activity has the objective of promoting a widespread use of in-situ experimental analysis and of reducing TRT costs and time duration of the experimental analysis. The considerations exposed in the present paper lead to reconsider a particular variety of the TRT in particular the version known as Thermal Response Test while Drilling (TRTWD).

In response to the growing need for efficient energy conversion technologies, this pa-per introduces an innovative Tubular Thermoelectric Generator (TTEG), specifically de-signed for high-efficiency conversion of waste heat into electrical energy. Unlike conven-tional flat plate thermoelectric generators (FTEGs), the TTEG incorporates full-ring ther-moelectric elements within a tubular layout, offering a novel approach to thermal energy recovery from fluid-based systems. This design significantly enhances the heat transfer capabilities, thereby improving the efficiency of energy conversion. Comprehensive simulations and analyses form the core of this study, where the per-formance of the TTEG is rigorously compared with traditional FTEGs. These comparisons highlight the advantages of the tubular design in terms of energy conversion efficiency and practical applicability in various scenarios. The findings reveal that the TTEG not only outperforms its flat plate counterparts but also presents a scalable and adaptable so-lution for waste heat recovery in a wide range of industrial and automotive applications. This research contributes to the field of energy science and technology by presenting a detailed experimental setup, complete with reproducible procedures and results. It opens new pathways for the development of more sustainable and efficient energy conversion systems, aligning with the goal of harnessing renewable and sustainable energy sources. The potential applications of this technology in enhancing energy efficiency and reducing environmental impact are vast, making it a significant step forward in the quest for clean and sustainable energy solutions.

In order to further control the equivalent circulating density,a new type of annular pres-sure-reducing downhole tool for high temperature and high pressure wells-liquid-absorbing ECD tool is designed.Through this tool,the bottom hole pressure of the equivalent circulating drilling fluid can be close to its hydrostatic pres-sure,therebyachieving a deeper drilling depth.The tool is mainly composed of screw mo-tor,vortex blade,annular seal,universal joint and drill string.Its working principle is mainly to use the liquid absorption effect of the tool and the hydraulic energy of the circu-lating fluid extracted by the screw motor to convert it into mechanical energy,and to gen-erate suction force to improve the flow energy of the drilling fluid in the bottom hole an-nulusand reduce the equivalent circulation density.Based on ANSYS-FLUENT analysis andsimulation,the change of pressure drop characteristics under different drilling fluid density,displacement and tool size was simulated.The simulation results show that thedepressurization effect is 1.0MPa when the drilling fluid density is 1.2g/cm3. When the drilling fluid density is 1.5g/cm3,the depressurization is about 1.7MPa,and when thedrill-ing fluid density is 1.8g/cm3,the depressurization is about 1.9MPa.When the drilling fluid density is 2.0g/cm3,the pressure drop is about 2.3MPa.When the flow rate is from 1500-2500L/min,the maximum pressure can be reduced by 2.3MPa.When the viscosity is 40mPa•S and 60mPa•S,the pressure drop almost does not change.The increase of viscosi-ty has little effect on the pressure drop,and it is mainly affected by the flow rate under equal displacement.

The purpose of this study is to examine the relationship between the institutional investors which can affect financial performance for corporate sustainability on the income smoothing. Therefore, this study focus on the connection between the nature of stock rights and income smoothing in China. For this study, hypotheses were established on the relationship each state-controlled companies, income smoothing, and information equilibrium of individual investors, and empirical analysis was conducted through related variables. The analysis results are summarized in three categories as follows. First, this research finds that state-controlled firms (CONTs) prefer income smoothing activities compared to non-state-controlled firms for the long-term sustainable development of firms using data from 2011 to 2019. Second, this study found out that Institutional investors support the behavior of CONTs to smooth their earnings because this behavior is seen as an attempt by CONTs to convey valuable private information to other investors. Third, we was able to discover that institutional investors' monitoring effect is predominantly driven by pressure-resistant institutional investors. This research complements the lack of empirical research on income smoothing and enable to give a guideline that the type of stock rights is a critical key determinant of participation in income smoothing activities for stable growth and sustainability in the future.

We have suggested earlier a new sustainable method for permafrost thermal stabilization that combines passive screening of solar radiation and precipitation with active solar-powered cooling of the near-surface soil layer thus preventing heat penetration in depth. Feasibility of this method has been shown by calculations, but needed experimental proof. In this article, we are presenting the results of soil temperature measurements obtained at the experimental implementation of this method outside of the permafrost area which actually meant higher thermal loads than in Polar Regions. We have shown that near-surface soil layer is kept frozen during the whole summer, even at air temperatures exceeding +30°C. Therefore, the method has been experimentally proven to be capable of sustaining soil frozen even in more extreme conditions than expected in permafrost areas. In addition to usual building and structure thermal stabilization, the method could be used to prevent the development of thermokarst, gas emission craters, and landslides; greenhouse gases, chemical, and biological pollution from the upper thawing layers at least in the area of human activities; protection against coastal erosion; and permafrost restoration after wildfires. Using commercially widely available components, the technology can be scaled up for virtually any size objects.

This study investigates the impact of environmental factors on intradialytic blood pressure in hemodialysis patients, using a four-year retrospective analysis. Employing a Generalized Estimating Equation (GEE) model, we examined the associations between clinical variables, meteorological conditions (temperature, humidity, wind speed, and precipitation), and blood pressure outcomes, including systolic blood pressure (SBP) and mean arterial pressure. Our results reveal that higher temperatures, increased humidity, and stronger wind speeds are significantly associated with lower SBP and mean arterial pressure. In contrast, higher daily precipitation correlates with elevated mean arterial pressure. Among clinical factors, erythropoiesis-stimulating agent (ESA) dosage shows a positive association with both SBP and mean arterial pressure while a history of intradialytic hypotension and increased interdialytic weight gain are negatively correlated. Additionally, serum potassium levels were inversely related to SBP and mean arterial pressure. These findings highlight the importance of incorporating environmental variables into predictive models for intradialytic blood pressure management. We propose tailored interventions, such as weather-adapted fluid management strategies, personalized treatment plans, and patient education, to mitigate potential adverse effects. This study provides a foundation for enhancing patient-centered care and improving the quality of life for hemodialysis patients amid global climate changes.

One of the most common solutions to access underground is through the construction of circular shafts. At preliminary design stage analytical expressions are often used to estimate the horizontal earth pressure acting on the lining. However, most of these solutions are based on active state conditions and do not consider the restrictions imposed on the shaft lateral displacements by the rigidity of its lining or by the construction method employed. To overcome this limitation a new methodology to account with the shaft lateral displacements in the determination of the horizontal earth pressure acting on circular shafts is developed and validated against the results of relevant physical scale models. The obtained results show good agreement with the measured data, reproducing adequately the reduction of the horizontal earth pressure from its initial value to an active state condition with the increase of the shaft lateral displacement. Following this approach more realistic predictions of the earth pressure acting on the lining of circular shafts can be performed.

Using the example of III-V nitrides crystallizing in a wurtzite structure (GaN, AlN, InN), this review presents the special role of hydrostatic pressure in studying semiconductor properties. Starting with a brief description of high pressure techniques for growing bulk crystals of nitride compounds, we focus on the use of hydrostatic pressure techniques in both experimental and theoretical investigations of special properties of nitride compounds, their alloys and quantum structures. The band gap pressure coefficient is one of the most important parameters in semiconductor physics. Trends in its behavior in nitride structures, together with trends in pressure-induced phase transitions, are discussed in the context of the behavior of other typical semiconductors. Using InN as an example, the pressure-dependent effects typical of very narrow bandgap materials, such as conduction band filling or effective mass behavior, are described. Interesting aspects of bandgap bowing in In-containing nitride alloys, including pressure and clustering effects, are discussed.Hydrostatic pressure also plays an important role in the study of native defects and impurities, as illustrated by the example of nitride compounds and their quantum structures. Experiments and theoretical studies on this topic are reviewed. Special attention is given to hydrostatic pressure and strain effects in short periods nitride superlattices. The explanation of the discrepancies between theory and experiment in the optical emission and its pressure dependence from InN/GaN superlattices led to the well-documented conclusion that InN growth on the GaN substrate is not possible. The built-in electric field present in InGaN/GaN and AlGaN/GaN heterostructures crystallizing in wurtzite lattice can reach several MV/cm, leading to drastic changes in the physical properties of these structures and related devices. It is shown how hydrostatic pressure modifies these effects and helps to understand their origin.

Hydrodynamic resistance is a critical parameter in microfluidics, affecting device functionality and performance. However, quantifying hydrodynamic resistance in microfluidics is a challenge due to many influencing factors and the difficulties associated with the precise measurements of low flow rates (< 10 L/min) and pressure drops (< 5 kPa). This article presents a simple experimental test method for assessing hydrodynamic resistance, correlating with theoretical and numerical calculations. The results demonstrate good agreement between benchtop and theoretical data, suggesting a potential standardized method for assessing hydrodynamic resistance in microfluidic devices.

Membrane-based sensors (MePSs) exhibit remarkable precision and sensitivity in detecting pressure changes. MePSs are commonly used to monitor catalytic reactions in solution, generating gas products crucial for signal amplification in bioassays. They also allow catalyst quantification by indirectly measuring the pressure generated by the gaseous products. This is particularly interesting to detect enzymes in biofluids associated with disease onset. To enhance the performance of a MePS, various structural factors influence membrane flexibility and response time, ultimately dictating the device's pressure sensitivity. In this study, we fabricated MePSs using polydimethylsiloxane (PDMS) and investigated how structural modifications affect the Young's modulus (E) and residual stress (σ0) of the membranes. These modifications have a direct impact on the sensors' sensitivity to pressure variations, observed as a function of the volume of the chamber (Σ) or of the mechanical properties of the membrane itself (S). MePSs exhibiting the highest sensitivities were then employed to detect catalyst quantities inducing the dismutation of hydrogen peroxide, producing dioxygen as gaseous product. As a result, catalase enzyme was successfully detected using these optimized MePSs, achieving a remarkable sensitivity of (22.7 ± 1.2) µm/nM and a limit of detection (LoD) of 396 pM.

We have successfully synthesized a series of Bi doped BaFe2As2 high quality single crystals for the first time. The x-ray diffraction (XRD) patterns show an expansion of lattice parameter c with Bi doping, indicating a negative pressure effect. By investigating the resistivity, a Fermi liquid (FL) to non-Fermi liquid (NFL) crossover is observed from normal state to antiferromagnetic order state, accompanied by three superconducting transitions labeled as SC I, SC II and SC III which are supposed to be induced from three superconducting realms with various Bi concentration. Thus, the NFL behavior is proposed to be closely related with the presence of superconductivity. The magnetic susceptibility measurements further speculates that the SC I and SC III phases should be filamentary superconductivity while the SC II be a possible bulk superconductivity with TC 7 K.

Runaway electrons (RAEs) generation in high-pressure gases is an important physical phenomenon that influences significantly discharge shapes and properties of initiated plasma. The diffuse discharges formed due to RAEs in air and other gases at atmospheric pressure find wide application. In the present review, theoretical and experimental results that explain the reason for the RAEs occurrence at high pressures are analyzed and recommendations are given on the implementation of conditions under which the runaway electron beam (RAEB) with the highest current can be obtained at atmospheric pressure. Experimental results were obtained using subnanosecond, nanosecond, and submicrosecond generators, including those specially developed for runaway electron generation. The RAEB were recorded by oscilloscopes and collectors with picosecond time resolution. To describe theoretically the phenomenon of continuous electron acceleration, the method of physical kinetics has been used based on the Boltzmann kinetic equation that takes into account the minimum but sufficient number of elementary processes, including shock gas ionization and elastic electron scattering. Results of modeling allowed the main factors to be established that control the RAE appearance, the most important of which is electron scattering on neutral atoms and/or molecules. Theoretical modeling has allowed the influence of various parameters (including the voltage, pressure, gas type, and geometrical characteristics of the discharge gap) to be taken into account. The results of research presented here allow the RAEs accelerators with desirable parameters to be developed and the possibility of obtaining diffuse discharges to be accessed under various conditions. The review consists of the Introduction, 5 Sections, the Conclusion, and the References.

This paper presents the experimental campaign conducted near the Condoroma dam at 4075 m a.s.l. in an experimental setup consisting of a series of standard profile spillways with a vertical upstream face of up to five different dimensionless heights (P/Hd). The experimental results indicate that for all P/Hd ratios studied, the discharge coefficients adjusted to the Condoroma altitude are lower than those reported by classical formulations used in conventional spillway design. As a result, a generalized equation is proposed to estimate the discharge coefficient for standard spillways located in dams at similar elevations above sea level.

A study was conducted on the power system of a forklift equipped with PEM fuel cells. A fuel cell assembly relies on several components for proper functioning, and among these, the air compressor holds paramount importance due to its significant energy consumption when compared to other Balance of Plant components. The air supply system, in turn, plays a critical role in ensuring the stable and efficient operation of the entire fuel cell system. To enhance system efficiency, we delved into the impact of varying the stoichiometric ratio of air and air pressure on the validated and optimized power module model. This investigation was carried out under real loading conditions, replicating the conditions experienced by the power module when fuel cells are in use within a forklift. The air compressor, being a pivotal component of a PEM fuel cell system, can be oper-ated at different excess air and pressure ratios, which in turn influence both the fuel cell's performance and the overall efficiency of the power module system. Our research focused on assessing the performance of polymer electrolyte membrane (PEM) fuel cells under different load cycles, adhering to the VDI60 requirements for forklift applications. This comprehensive examination encompassed the system's minimum and maximum load scenarios, with the primary goal of optimizing excess air and pressure ratio parameters, especially under dynamic load conditions. The results revealed that higher air pressures and lower excess air ratios were con-ducive to increasing system efficiency, shedding light on potential avenues for enhancing the performance of PEM fuel cell systems in forklift applications.

The service life of the reinforced concrete structure in the marine environment can be impaired significantly due to chloride-induced corrosion. However, how the chloride diffusion in pre-cracked concrete structures is affected by the hydrostatic pressure magnitude is poorly understood. This study experimentally examined the effect of hydrostatic pressure on the chloride diffusion in pre-cracked concrete. Cracks with five different widths, i.e., 20 μm, 40 μm, 60 μm, 80 μm, and 100 μm, were manually created using a splitting tensile apparatus respectively. The chloride diffusion in the concrete with a certain crack was then studied under four different hydrostatic pressures of 0 MPa, 0.1 MPa, 0.3 MPa, and 0.5 MPa. Experimental results show that the chloride diffusion in concrete with a crack greatly relies on both the hydrostatic pressure and the crack width. The chloride concentration increases as the hydrostatic pressure grows, particularly for the wider cracks with width ranging from 60 μm to 100 μm. Surprisingly, the hydrostatic pressure has a negligible effect on the chloride distribution in the concrete with a crack width no larger than 40 μm. Both the chloride diffusion coefficient and the surface chloride concentration of concrete increased gradually as the hydrostatic pressure increased. The experimental findings enrich our understanding of the behavior of pre-cracked concrete when exposed to chloride-induced corrosion at different depths of marine environments.

The high protein content of several microalgal species makes them attractive and unconventional for applications in the food and pharmaceutical industries. Due to microalgae's robust cell wall, cell rupture is necessary to improve the extraction of their intracellular proteins. Thus, choosing a suitable cell-breaking treatment before protein extraction is a vital downstream processing step. Additionally, it is necessary to use an effective technique for monitoring and measuring the impact of rupture treatments on microalgal cell walls. In our study, Tetradesmus obliquus cells were disrupted by three different mechanical rupture methods: high-pressure homogenization (HPH), ultrasound (US), and ball milling (BM). The ruptured biomass cells were counted, and soluble proteins were extracted and quantified. The cell counting technique did not detect differences between intact and damaged cells after BM treatment because the dye (erythrosine B) did not permeate the microalgae biomass accurately. The US treatment promoted the highest yield of total protein extraction (19.95%). The yields of protein extraction of T. obliquus with HPH (15.68%) and BM (14.11%) were significantly (p value ≤ 0.05) lower than that achieved in the US treatment. The increase in the number of extraction steps increased the protein recovery. Thus, the content of extracted soluble protein was a reliable indirect index for a quantitative comparison of the cell disruption level.

Consumption of high amounts of ethanol is a risk factor for development of cardiovascular diseases such as arterial hypertension. The hypertensive state induced by ethanol is a complex multi-factorial event, and oxidative stress is a pathophysiological hallmark of vascular dysfunction associated with ethanol consumption. Increasing levels of reactive oxygen species (ROS) in the vasculature triggers important processes underlying vascular injury, including accumulation of intracellular Ca2+ ions, reduced bioavailability of nitric oxide (NO), activation of mitogen-activated protein kinases (MAPKs), endothelial dysfunction, and loss of the anticontractile effect of perivascular adipose tissue (PVAT). The enzyme nicotinamide adenine dinucleotide phosphate (NADPH) oxidase plays a central role in vascular ROS generation in response to ethanol. Activation of the renin-angiotensin-aldosterone system (RAAS) is an upstream mechanism which contributes to NADPH oxidase stimulation, overproduction of ROS and vascular dysfunction. This review discusses the mechanisms of vascular dysfunction induced by ethanol, detailing the contribution of ROS to these processes. Data examining the association between neuroendocrine changes and vascular oxidative stress induced by ethanol are also reviewed and discussed. These issues are of paramount interest to public health as ethanol contributes to blood pressure elevation in the general population, and it is linked to cardiovascular conditions and diseases.

Numerical simulations and experiments on evaporative condensers in air conditioning systems using R744 were performed. Two configurations were given to study the feasibility of operating the subcritical R744 cycle. It indicated the capable of evaporative cooling condensing R744 to liquify by analyzing the outlet temperature at the end of the condenser reached from 28.7oC to 30.3oC with the operating pressure from 72.6 bar to 68.5 bar. The mass flow rate in the study increases from 14.34 kg/h to 46.08 kg/h, the pressure drop also increases from 0.23 bar to 0.47 bar for the simulation and 0.4 bar to 0.5 bar for the experiment, respectively. This study indicates that a 5-layers of copper tubes configuration causes a higher pressure drop and lower COP when compared to an 8-layers of copper tubes that split into 2 sets for smaller pressure drop. In this study, the evaporative condensers using mini tubes that are flooded in the cooling water tank are suitable for the subcritical R744 air conditioning system. The results obtained from the experimental data are in good agreement with those obtained from the numerical results, with the deviation less than 5%.

GDF5 gene is involved in the development of skeletal elements, synovial joint formation, tendons, ligaments, and cartilage. Several polymorphisms are present within the gene and two of them, rs143384 and 143383, have been reported as correlated with osteoarticular disease or muscle flexibility. The aim of this research is to verify if the worldwide distribution among human populations of rs143384 polymorphism has been shaped by selective pressure, or if it’s the result of random genetic drift events. Ninety-four individuals of both sexes, 18-28 years old, from Sardinia were analyzed. We observed the following genotype frequencies: 28.72% of homozygotes AA, 13.83% of homozygotes GG, and 57.45% of heterozygotes AG. Allele frequencies were 0.574 for allele A and 0.426 for alle G. Relationships between populations were verified by Multidimensional Scaling (MDS). Our data show: i) a clear heterogeneity within the African populations; ii) a strong differentiation between Africans and the other populations: iii) the Sardinian population is placed withing the European cluster. To reveal possible traces of selective pressure, Population Branch Statistic (PBS) was calculated; both SNPs rs143384 and 143383 have low PBS values, suggesting that there are no signals of selective pressure in those areas of the gene.

The close proximity of different buildings heights can cause disturbances in the working of the smoke and ventilation ducts of lower buildings, threatening the health and even the lives of residents. To define the influence of high-rise building on the work of the ducts of the neighbouring double-storied building, experimental investigations in the wind tunnel were conducted. On this basis, empirical equations and graphs were developed leading to determining the aerodynamic coefficients considering different wind directions and the height of ducts. The direction of the wind reveals a greater influence than the height of the ducts. Properly using deflectors or increasing the height of the duct ensures maintaining static rarefaction in the area of smoke and ventilation ducts. The creation of rarefaction ensures the reliability of the natural ventilation system and the safety of the health of residents.

A numerical method using combined detached-eddy simulation (DES) and cavitation model considering the rotation effect is used for unsteady cavitation flow field of the centrifugal pump. Closed type pump test system was established to obtain the pump performance and pressure pulsation characteristics under different flow rates and cavitation condition, which provide boundary conditions and verification of calculations. Based on the calculation results of the unsteady flow field of the centrifugal pump cavitation, the entropy generation analysis of the flow field and the pressure fluctuation characteristics were carried out. Then the relationship between cavitation and the deterioration of the centrifugal pump performance and the generation of the unstable operation excitation force was tried to reveal. The internal energy loss is mainly concentrated in the impeller, volute, and pump cavity area, which accounts for more than 85% of the total entropy generation. The characteristic frequency of about 0.333 Strouhal Number appears at the volute tongue due to the cavitation flow spread downstream.

Pipe leakage is an inevitable phenomenon in water distribution networks (WDNs), leading to energy waste and economic damage. Leakage events can be reflected quickly by pressure values, and the deployment of pressure sensors is significant for minimizing the leakage ratio of WDNs. Concerning the restriction of realistic factors, including project budgets, available sensor installation locations, and sensor fault uncertainties, a practical methodology is proposed in this paper to optimize pressure sensor deployment for leak identification in terms of these realistic issues. Two indexes are identified to evaluate the leak identification ability, that is, detection coverage rate (DCR) and total detection sensitivity (TDS), and the principle is to determine priority to ensure an optimal DCR and retain the largest TDS with an identical DCR. Leakage events are generated by a model simulation and the essential sensors for maintaining the DCR are obtained by subtraction. In the event of a surplus budget, and if we suppose the partial sensors have failed, then we can determine the supplementary sensors that can best complement the lost leak identification ability. Moreover, a typical WDN Net3 is employed to show the specific progress, and the result shows that the methodology is largely appropriate for real projects.

High temperatures (HT) and high hydrostatic pressures (HHP) are characteristic of deep-sea hydrothermal vents and other deep crustal settings. These environments host vast and diverse microbial populations, yet only a small fraction of those populations have been successfully cultured. This is due, in part, to the difficulty of sampling while maintaining these in situ conditions and also replicating those high-temperature and high-pressure conditions in the laboratory. In an effort to facilitate more HT-HHP cultivation, we present two HT-HHP batch culture incubation systems for cultivating deep-sea vent and subsurface (hyper)thermophilic microorganisms. One HT-HHP system can be used for batch cultivation up to 110 MPa and 121°C, and requires sample decompression during subsampling. The second HT-HHP system can be used to culture microorganisms up to 100 MPa and 160°C with variable-volume, pressure-retaining vessels that negate whole-sample decompression during subsampling. Here, we describe how to build cost effective heating systems for these two types of high-pressure vessels, as well as the protocols for HT-HHP microbial batch cultivation in both systems. Additionally, we demonstrate HHP transfer between the variable-volume vessels, which has utility in sampling and enrichment without decompression, laboratory isolation experiments, as well as HHP filtration.

BACKGROUND: To present a new method of urethral pressures examination, and to evaluate diagnostic capabilities of three dimensional profilometry , as an alternative to classical urethral profile (UPP) .Using four channel catheters and dedicated software global urethral pressures image is obtained. The method eliminates the main limitation of classical urethral profilometry where the catheter orientation determines the pressures picture limited to only one point in the uretral circumference while we observed even 50% differences in pressure measures depending on the point of measurement. METHODS: This is a preliminary study containing method presentation and analisys of the use in varied clinical cases of either healthy patients and patients with LUTS. The article includes technique and equipment decription, full evaluation of selected cases, including three dimensional urethral pressures distribution graphics. RESULTS AND CONCLUSIONS:Three dimensional profilometry compared to classical technique is comparable regarding the time, cost, technical difficulty and patient discomfort. At the same time we obtain much more data on the urethral pressures and its distribution.The results are easy for interpretation due to 3D movable graphics created automatically through the dedicated software.

To compare surgical and refractive outcomes between phacotrabeculectomy (P-Trab) and phaco with Ex-PRESS (P-Ex-PRESS) for glaucoma at 6-month follow-up. This prospective randomized controlled trial included 81 eyes; 43 (53%) and 38 (47%) were assigned to the P-Ex-PRESS and P-Trab groups, respectively. Refraction, intraocular pressure (IOP), and best-corrected visual acuity were measured. Refractive change was described by analyzing the magnitude of the cylinder, and polar analysis assessed the change in trend of astigmatism [with-the-rule, against-the-rule (ATR), oblique] evaluating mean astigmatism in centroid form. All patients showed statistically significant postsurgical decrease in IOP (P&lt;0.05). There were no differences neither between the groups for postoperative IOP or visual outcomes, nor in astigmatism before or after surgery (P=0.61, P=0.74). In both groups, the mean pre- and postoperative astigmatism was ATR and OBL, respectively. Pre- and postoperative centroids in the P-Ex-PRESS group were 0.44±1.32 D at 177˚ and 0.35±1 D at 8˚, respectively, (P=0.5) and in the P-Trab group, 0.16±1.5 D at 141˚ and 0.39±1.38 D at 29˚, respectively (P=0.38). Both P-Ex-PRESS and P-Trab showed comparable antihypertensive efficacy in treating open-angle glaucoma in a 6-month period. Pre- and postoperative astigmatism did not differ between groups. The groups showed comparable results for final visual acuity.

The zero velocity update(ZUPT) algorithm is the core of a foot-mounted pedestrian navigation system. The zero velocity detection method is the premise and guarantee of the effective application of the ZUPT algorithm. To make ZUPT work properly, it is necessary to detect zero velocity intervals correctly. The detection accuracy of the existing zero velocity detection methods is easy to be affected by users and environment. A novel zero velocity detection method based on the plantar pressure is proposed in this paper, which has higher detection accuracy and better environmental adaptability. First, the paper analyzes the motion characteristics of foot during walking. Second, the inherent relationship between the plantar pressure and the gait change during walking is studied based on the pressure sensor. Then, the model of the zero velocity detection method using the plantar pressure is established. Finally, the indoor and outdoor multi-scene experiments show that this method not only has a high detection accuracy, but also has good adaptability to users and walking environment.

With the emergence of COVID-19 we are confronted with a new clinical picture of acute respiratory distress syndrome in the intensive care unit. In the majority of patients, the respiratory mechanics are very different from the “normal” ARDS patient. We measured transpulmonary pressure and dead space ventilation to assess the effects of high and low PEEP levels on lung compliance and ventilation-perfusion mismatching. Advanced respiratory mechanics were assessed in 14 patients. Compared to ARDS patients, lung compliance was relatively high (61 ± 5 mL/cmH₂O). COVID-19 patients had high dead space ventilation and gas exchange impairment (Bohr 52 ± 3%; Enghoff modification 67 ± 2%; ventilatory ratio 2.24 ± 0.23). we show that higher PEEP levels decrease lung compliance and in most cases increase dead space ventilation, indicating that high PEEP levels probably cause hyperinflation in patients with COVID-19. We suggest using prone position for an extended period of time, and apply lower PEEP levels as much as possible.

The aim of this paper is the presentation of an analytical model of insulator flashover and its application for air at atmospheric pressure and pressurized SF6. After a review of the main existing models in air and compressed gases, we develop a relationship of flashover voltage on the basis of an electrical equivalent circuit and the thermal properties of the discharge. The model includes the discharge resistance, the insulator impedance, and the gas interface impedance. The application of this model to a cylindrical resin-epoxy insulators in air medium and SF6 gas with different pressures gives results close to the experimental measurements.

Abstract In order to reduce the failure accidents of conventional packers, a kind of sealing structure of retrievable packers is designed, which can provide reference for optimizing the sealing performance and pressure capacity of packers. And theoretical calculation and experimental research on its sealing performance and pressure capacity are carries out through the finite element analysis on the contact with large deformation based on Abaqus and experimental. The results show that when the rubber cylinder of retrievable packers in the sealing process, the upper packer is subjected to greater stress and mainly plays a sealing role. In order to improve the sealing performance of packer, the height of upper and lower packer should be preferentially selected about 60 mm, the height of middle rubber cylinders should be about 50 mm, and the thickness of packer should be about 21 mm. The newly designed rubber cylinders can meet 150 ℃. Sealing and pressure-bearing function under the condition of 10000 Psi. The rubber cylinder of newly designed can satisfy the function of sealing and pressure-bearing under 140 ℃ and 10000 Psi. The whole experiment shows that the capacity of bearing pressure and sealing is stable, which can better meet the requirements of field use.

1) Background: Spirulina (Arthrospira) maxima has shown beneficial effects such anti-dyslipidemic, antiviral, antioxidant and antihypertensive. However, there are few and limited clinical studies. 2) Methods: a prospective, randomized, parallel pilot study of 4.5 g administration of Spirulina maxima or placebo for 12 weeks in 16 patients with systemic arterial hypertension undergoing treatment with ACE inhibitors was performed to assess the effects on endothelial damage and oxidative stress indicators. The blood levels of sICAM-1, sVCAM-1, endothelin-1, and sE-selectin were quantified; the activities of catalase, superoxide dismutase, glutathione peroxidase, glutathione reductase and concentrations of reduced glutathione, oxidized glutathione, and thiobarbituric acid reactive susbtances, were also quantified before and after the treatment period. 3) Results: There were statistically significant (p < 0.05) decreases in systolic blood pressure, sVCAM-1, sE-selectin and endothelin-1 levels, and increases in glutathione peroxidase activity and oxidized glutathione levels. 4) Conclusion: The effects found in the present study agree with antihypertensive and antioxidant effects previously reported for Spirulina maxima. However, this is the first report about the effects on indicators of endothelial damage. More research in this field is necessary to gain an insight into the effects of Spirulina on these indicators.

Glucosamine is the most common nutrition supplement used in the United States. It is promoted not only as a pain reliever but also a therapy to slow osteoarthritis. Although studies with 3,800 patients with osteoarthritis of the knee or hip found that glucosamine was no better than placebo, it continues to be used for these two indications due to its perceived safety. However, reports of an increased intraocular pressure are alarming, especially in glaucoma. Glycosaminoglycans play a key role in the physiology of the cornea, conventional outflow of aqueous humor and the retina. In theory, long-term treatment with glucosamine could reach a concentration that impacts the morphology and function of ocular tissues. We recommend ophthalmologists counsel glaucoma patients about the potential risks of glucosamine and encourage cessation in uncontrolled intraocular pressure.

The photoreduction of CO2 is an intriguing process, which allows the synthesis of fuels and chemicals. One of the limitations for CO2 photoreduction in the liquid phase is its low solubility in water. This point has been here addressed by designing a fully innovative concept of pressurized photoreactor, allowing operation up to 20 bar and applied to improve the productivity of this very challenging process. The photoreduction of CO2 in the liquid phase was performed using commercial TiO2 (Evonink P25), TiO2 obtained by flame spray pyrolysis (FSP) and gold doped P25 (0.2 wt% Au-P25) in the presence of Na2SO3 as hole scavenger (HS). The different reaction parameters (catalyst concentration, pH and amount of HS) have been addressed. The products in liquid phase were formic acid and formaldehyde. Moreover, for longer reaction time and with total consumption of HS, gas phase products formed (H2 and CO) after accumulation of significant amount of organic compounds in the liquid phase, due to their consecutive photoreforming. Enhanced CO2 solubility in water was achieved by adding a base (pH= 12-14). In basic environment, CO2 formed carbonates which further reduced to formaldehyde and formic acid and consequently formed CO/CO2+H2 in the gas phase through photoreforming. The deposition of small Au nanoparticles (3-5 nm) (NPs) onto TiO2 was found to quantitatively influence the products distribution and increase the selectivity towards gas phase products.

The aim of this paper is to explore the watertightness behaviour for high pressure applications using Multijetfusion technology and polyamide 12 as a material. It reports an efficient solution for manufacturing functional prototypes and final parts for water pressure applications. It provides manufacturing rules to engineers in the pressurized product development process up to 10 MPa of nominal pressure. The research findings show manufacturers the possibility of using additive manufacturing as an alternative to traditional manufacturing. Water leakage was studied using different printing orientations and wall thickness for a range of pressure values. An industrial ball valve was printed and validated with the ISO 9393 standard also meeting tolerance requirements. This paper is a pioneering approach to the additive manufacturing of high performance fluid handling components. This approach solves the problem of leakage caused by porosity in additive manufacturing technologies

We conducted an in-situ crystal structure analysis of ferroselite at non-ambient conditions. The aim is to provide a solid ground to further the understanding of the properties of this material in a broad range of conditions. Ferroselite, marcasite-type FeSe2, was studied under high pressures up to 46 GPa and low temperatures, down to 50 K using single-crystal microdiffraction techniques. High pressure and low temperatures were generated using a diamond anvil cell and a cryostat. We found no evidences of structural instability in the explored P-T space. The deformation of the orthorhombic lattice is slightly anisotropic. As expected, the compressibility of the Se-Se dumbbell, the longer bond in the structure, is larger than that of the Fe-Se bonds. Less obvious is the behavior of the octahedral bonds, the shorter bond is the most compressible determining a small increase in the octahedron distortion with pressure. We also achieved a robust structural analysis of ferroselite at low temperature in the diamond anvil cell. Structural changes upon temperature decrease are small but qualitatively similar to those produced by pressure.

In this article, a novel hybrid welding process called plasma-TIG coupled arc welding was proposed to improve the efficiency and quality of welding by utilizing the full advantage of plasma and TIG welding processes. The two arcs of plasma and TIG were pulled into each other into one coupled arc under the effect of Lorentz force and plasma flow force during welding experiments. The arc behavior of coupled arc was studied by means of it’s arc profile, arc pressure and arc force conditions. The coupled arc pressure distribution measurements were performed. The effects of welding conditions on coupled arc pressure were evaluated and the maximum coupled arc pressure was improved compared with single-plasma arc and single-TIG arc. It was found that the maximum arc pressure was mainly determined by plasma arc current and plasma gas flow. According to the results, the proposed coupled arc welding process have both advantages of plasma arc and TIG method, and it has a broad application prospect.

Moisture and thermal are the key factors for influencing methane desorption during CBM exploitation. Using high pressure water injection technology into coalbed, new fractures and pathways are formed to methane transport. It is existed a phenomenon of water inhibiting gas flow. This study is focused on various water pressures impacted on gas adsorbed coal samples, then the desorption capacity could be revealed under different conditions. And the results are shown that methane desorption capacity was decreased with water pressure increased at room temperature and the downtrend would be steady until water pressure was large enough. Heating could promote gas desorption capacity effectively, with the increasing of water injection pressures, the promotion of thermal on desorption became more obvious. These results are expected to provide a clearer understanding of theoretical efficiency of heat water or steam injection into coalbed, they can provide some theoretical and experimental guidance on CBM production and methane control.

Due to the periodic movement of the piston in the reciprocating pump, the fluid will cause pressure pulsation, and the vibration of the pipeline will lead to instrument distortion, pipe failure and equipment damage. Therefore, it is necessary to study the vibration phenomena of the reciprocating pump pipeline based on the pressure pulsation theory. This paper starts from the reciprocating pump pipe pressure pulsation caused by fluid, pressure pulsation in the pipeline and the excited force is calculated under the action of the reciprocating pump. Then, the numerical simulation model is established based on the pipe beam model, and the rationality of the numerical simulation method is verified by the indoor experiment. Finally, a case study is taken as an example to analyze the vibration law of the pipeline system, and proposed the stress reduction and vibration reduction measures. The main conclusions are drawn from the analysis: (1) Excited force is produced in the bend or tee joint, and it can also influence the straight pipe in different levels; (2) In this pipeline system, the pump discharge pipe has a larger vibration amplitude and lower natural frequency; (3) The vibration amplitude increases with the pipe thermal stress, and when the oil temperature is higher than 85°C, it had a greater influence on the vertical vibration amplitude of the pipe.

Heat stress (HS) is a strong stress factor that significantly affects the metabolism of dairy cows. The aim of the present study was to investigate how HS affects some biochemical indicators in the blood of dairy cows reared in Bulgaria. The study was conducted on a cattle farm with a capacity of 500 Holstein cows, loose housed in a free stall barn shed type. The research was carried out in three seasons - summer, autumn and winter, and a total of 77 samples were taken from the cows of the farm - 30 blood samples for each season. The cows included in the study were from 30 to 60 days in milk (DIM). Temperature and humidity data were taken from the closest to the farm weather station. Based on the conducted research, it was found that the HS reported during the summer season had a significant impact on the following blood parameters: glucose, urea, total protein and cortisol. In summer, blood glucose values were low and ranged from 1.32 to 1.63 mmol/l in cows on different lactations. Probably because of these low glucose levels, high levels of total protein, ranging from 76.92 to 86.10 g/l, were reported in cows from the first to third lactation. This protein was used by cows to provide energy from non-carbohydrate sources and as a residual product, higher blood urea levels were reported in summer, ranging from 4.79 to 5.23 mmol/l. As proof of the stressful influence of heat on the metabolism of the examined cows, the cortisol values in the summer were in the upper reference norms - 38.44 nmol/l or higher and reached 59.09 nmol/l.

Worldwide the severity of abiotic stress like heat, drought, salinity, cold, waterlogging, etc. are being increased because of global warming. Wheat crops must adapt to harsh environments through physiological, molecular, and genetic manipulation. Because of abiotic stress, reactive oxygen species (ROS) and reactive nitrogen species (RNS) produced in wheat plants break down DNA and RNA bases, protein, lipid, and other macro- and micromolecules, resulting in stunted growth and yield decline. Abiotic stress also induces the crop's molecular functions, physiological, biological, and cellular processes, and their compositions. Different stressors like high light intensity, heat, drought, and salinity also impair photosynthesis damaging various pigments. Antioxidant enzymes, such as catalase (CAT), superoxide dismutase (SOD), peroxidase (POD), and ascorbate peroxidase (APX), etc. synthesized in harsh environments can ameliorate ROS/RNS produced in oxidative stress. Under abiotic stress, heat shock proteins (HSPs) heat shock transcription factors (HSFs) in heat stress, and dehydration-responsive element binding proteins (DREBs) in drought stress are activated to synthesize proteins to mitigate the deleterious effects of those stressors. Na⁺ exclusive genes (NAX1, NAX2) and Na⁺/H⁺ (K⁺) antiporter genes (NHX1, NHX2) hinder those ions from uptake into leaf sheaths and blades of wheat resulting in the declination of salinity in plants. Exogenous hormones like gibberellic acid, salicylic acid, and melatonin, etc., and osmoprotectants like proline, and gene manipulation in plants through genetic engineering are being employed to mitigate the toxic effects of abiotic stress on plants, as portrayed in many literatures. The review depicts how abiotic stress affects phenotypic, physiological, and molecular structures and functions of wheat crops, and their mitigation strategies to lessen their noxious effects on wheat.

Heat index (HI) is a biometeorological indicator that combines temperature and relative humidity. This study aimed to investigate the relationship between heat index and daily counts of diarrhoea hospitalisation in Dhaka, Bangladesh. Data on daily diarrhoea hospitalisations and meteorological variables from 1981–2010 were collected. We categorised heat index of >94.3°F, >100.7°F and >105°F as high, very high and extremely high heat index, respectively. We applied time-series adjusted generalised linear model (GLM) with negative binomial distribution to investigate the effects of heat index and extreme heat index on hospitalisations for diarrhoea. Effects were assessed for all ages, <5 children and by gender. A unit higher HI, and high, very high and extremely high HI were associated with 0.8%, 8%, 7% and 9% increase in diarrhoea hospitalisation in all ages, respectively. The effects varied slightly by gender and were most pronounced in <5 children with a rise of 1°F in high, very high and extremely high HI associated with a 14.1% (95% CI: 11.3% – 17.0%), 18.3% (95% CI: 13.4% – 23.5%) and 18.1% (95% CI: 8.4% – 28.6%) increase of diarrhoea, respectively. This suggest that heat index may serve as an alternative indicator for measuring the combined effects temperature and humidity on diarrhoea.

This study examined the thermal reflective properties and mechanisms of composite inorganic coatings applied to various wall types. It evaluated the influence of these coatings on the thermal insulation and reflectivity of walls. The findings indicate that coating application markedly enhances the wall's thermal insulation capabilities and increases the heat flux reflection ratio. These results offer crucial theoretical backing and practical guidance for the future use of coating technologies in construction. By refining the coating formulations and application processes, the thermal insulation properties of walls can be further enhanced, thus making a significant contribution to building energy efficiency and environmental protection. Consequently, this research provides essential references and insights for advancing coating technology in the construction industry.

The consequences of heat stress during the dry period can extend into the postpartum period, affecting health and productivity in the subsequent lactation. We hypothesized that cows with distinct core body temperatures (CBT) would exhibit disparate behaviors associated with different degrees of heat generation or dissipation. The primary objective was to investigate behavioral differences of dry Holstein cows (n=50) classified as high-temperature (HT) or low-temperature (LT) based on median CBT during the summer months using visual observations and accelerometer technology. A secondary objective was to investigate the transcriptome of white blood cells (WBC) collected from a subgroup of HT and LT cows (n=5; per group). Minor behavior differences were observed during the visual observations (performed for a total of 16h/cow). Based on the accelerometer data, HT cows displayed higher periods of high activity and lower periods of inactivity prepartum and diminished rumination time postpartum than LT cows. There were 16 differently expressed genes (DEG) in WBC of HT than LT cows. Despite the low number, several of the identified DEGs have been previously associated with heat stress. Results indicate that CBT and patterns of activity prepartum may serve as valuable predictors for identifying dairy cows with distinct tolerance to heat stress.

The objective of this work is to analyze the improvement of heat transfer in trapezoidal fin heat exchangers using numerical simulation. Heat exchangers are essential components frequently used in contemporary electronic gadgets to effectively disperse heat produced by high-power components. Nevertheless, as electronic devices continue to advance and become more powerful, the heat transfer capacity of heat exchangers is facing more requirements, therefore requiring enhanced heat dissipation efficiency. Afterwards, various fin angles were adjusted, and the heat transmission efficiency was compared. Modifying the angles can significantly improve the effi-ciency of convective heat dissipation. Moreover, it has been found that employing an optimized trapezoidal fin structure can further enhance the efficiency of heat transfer. The results indicate that trapezoidal fin heat exchangers provide superior heat dissipation efficiency compared to conventional heat exchangers. This is important for enhancing the thermal dissipation capabili-ties of electrical gadgets, hence guaranteeing steady functionality and extending their longevity. Subsequent study might explore supplementary methods to boost heat transmission in different heat exchanger configurations in order to meet the growing requirements for heat dissipation.

The design complexity of the new generation of civil aero-engines results in higher demands on engines’ components, higher component temperature, higher heat generation, and, finally, critical thermal management issues. This paper will propose a methodological approach to create physics-based models for heat loads developed by sources as well as a systematic sensitivity analysis to identify the effects of design parameters on the thermal behaviour of civil aero-engines. The ranges and levels of heat loads generated by heat sources (e.g., accessory gearbox, bearing, pumps, etc.) and heat absorption capacity of heat sinks (e.g., engine fuel, oil, and air) are discussed systematically. The practical research challenges for thermal management system design and development for the new and next generation of turbofan engines will then be addressed through a sensitivity analysis of the heat load values as well as the heat sinks flow rates. The potential solutions for thermal performance enhancements of propulsion systems will be proposed and discussed accordingly.

Regeneratively cooled scramjet has already been successfully verified as propulsion device for hypersonic vehicle. As a result, dynamic process of flow and heat transfer in cooling channel is commonly occurred which may bring hazard and control difficulties for scramjet. To study transient flow and heat transfer process in cooling channel, a dynamic numerical model is established. Dynamic characteristics of flow and heat transfer under different conditions are calculated and discussed, which includes change of inlet fuel mass flow, heat flux and pressure working conditions. Results show that stable time of cooling channel outlet fuel temperature is related to the change rate of inlet mass flow and heat flux. The stable time of outlet fuel temperature under heat flux decreasing working conditions are about 12.5 s. The initial response of working pressure fluctuation will lead to fuel temperature fluctuation, which has little effect on wall temperature.

Background: Musculoskeletal pain is a non-negligible multifaceted condition affecting more than 30% of the global population. Superficial heat therapy (HT) through increasing tissues temperatures plays a role in increasing local metabolism and function and relieving pain. Knee pain and sports represent two relevant fields of superficial HT application. Methods: In the present paper a panel of experts performed a narrative review of the literature regarding the role of superficial HT in the management of knee pain and sport activities. Results: According to the reviewed literature, HT represents a therapeutic option in the management of musculoskeletal pain due to three main effects: pain relief, promotion of healing and return to normal function and activity. Moreover, HT plays a role in sport activities both before and after exercise. Before performing sports, HT helps in preparing muscles for performance. After performing sports, it is capable to promote recovery and healing pathways. Combining and sequencing superficial heat and cold therapy represent an interesting topic of study. Overall, application of heat wraps for superficial HT can be considered safe. Conclusions: Despite being an ancient method, HT shows to be a potentially beneficial and safe option in the management of several conditions including KP and sports. The key in the application of superficial HT is a multimodal and multidisciplinary approach.

This paper proposes a simulation technique for investigating the battery thermal management system based direct refrigerant cooling (BTMS-DRC). It employs finite element method for a combined-conduction-convection heat transfer to predict the module temperature and to prove the temperature uniformity. The refrigerant side cooling is based on the two-phase flow evaporation which is represented by the convection heat transfer (flow evaporation) under a certain refrigerant saturation temperature. The battery heat generation is modeled as the constant heat flux. The main module is modeled as the conduction heat transfer. The real BTMS-DRC is constructed for experimentation with the test bench which is based on the dual-evaporators vapour compression refrigeration system. The simulated result is validated with the experimental results to ensure the correction of the modelling. The simulation also investigates the impact of the heat generation, convection heat transfer coefficient, refrigerant saturation temperature, and thermal conductivity on the module temperature and temperature uniformity. It is found that the simulated results agree well with the experimental results. The errors are around 2.9 - 7.2% throughout the specified working conditions. Overall, the proposed technique can be used as a design tool for further developing the BTMS-DRC.

Geothermal energy is likely to be a significant contributor in achieving sustainable energy goals and net-zero emissions targets. Within geothermal power plants, heat exchangers play a critical role in harnessing this renewable energy source. However, these heat exchangers encounter significant challenges when exposed to geothermal fluids, including erosion, corrosion, and scaling, which adversely affects their performance and longevity. The current review focuses on surface engineering techniques, particularly coatings, as a highly effective and economically viable solution to address these challenges in geothermal heat exchangers. The review begins by providing an overview of geothermal energy, its significance in the context of sustainability and the important role played by heat exchangers in geothermal power generation, followed by the challenges and their impact on heat exchangers. The subsequent section focuses on surface engineering by coatings and its types employed to enhance the performance of heat exchangers. In the final part, the reader is presented with an overview of the challenges associated with the application of coatings in geothermal heat exchangers and potential future directions in this field. This review offers a detailed understanding of the critical role coatings play in improving the efficiency and service life of heat exchangers in geothermal power plants.

Is HSP-27 an emerging marker of good prognosis in septic shock patients – a pilot study Objective To estimate the value of serum changes of C-reactive protein, procalcitonin, presepsin, heat shock protein 27 (HSP27) and neutrophil to lymphocyte ratio in assessing the prognosis in patients with septic shock (SS) treated in intensive care unit. Methods The SS was diagnosed and treated in accordance with the guidelines of the Surviving Sepsis Campaign. 37 selected adult patients with SS were included. Serum concentrations of biomarkers were measured at admission and daily for 4 consecutive days (time points T0,T1, T2, T3 and T4 respectively). The mortality rate was determined 28 days after admission. Patients were divided into survivor and non-survivor groups according to their mortality. The differences between the levels of biomarkers at the T0 and T4 time points were analyzed. Results The mean value of the SOFA score on admission was 11.7 ± 2.7, and the APACHE II scale 29.9 ± 6.85. Nine patients died. Univariate logistic analysis revealed that changes between T0 and T4 time points of presepsin, procalcytonin, and HSP27 were associated with prognosis. A multivariate Cox analysis showed that an increase in HSP27 on T4 was the only independent predictor of good prognosis in SS patients. The area under the receiver operating characteristics curve for HSP27 was 0.785. Kaplan–Meier analysis showed that the mortality was lower (p=0.014) in patients who had an increase in HSP27 on T4 compared to those whose serum HSP27 did not increase on T4. Conclusions The increase of HSP27 level on the 4th day predicts favorable outcome in SS patients.

The heritage of ancient buildings is an important part of the world's history and culture, which has an extremely rich historical-cultural value and artistic research value. Beijing has a large number of palace ancient buildings, and because of the age of their construction, many of them have problems of varying degrees of peeling and mold on the inner surfaces of the envelope. To solve the problems of the damp and moldy interior of palace buildings, a mathematical model of indoor heat and moisture transfer was established based on a wooden palace ancient building in Beijing. Through the indoor mold distribution validation model, the effects of outdoor humidity, soil moisture, wall humidity, and other factors on the indoor heat and moisture transfer of ancient buildings were simulated and analyzed by using the control variables method. The results showed that the molds were distributed at the indoor corners and floors, and the simulation of indoor humidity match the measured humidity. Thus, the simulation results were consistent with the actual situation. The variable trend of the relative humidity of the indoor environment with the outdoor humidity is inconsistent from plane to plane, i.e. it increases or remains constant with the increase of the outdoor humidity. The indoor ambient relative humidity increased with increasing the wall humidity. And the indoor average temperature is 23.3 ℃ and indoor relative humidity ranged between 90.9 % to 92.44 %. Soil moisture and wall humidity were the main factors affecting the indoor environmental relative humidity.