The option of decarbonizing urban freight transport using Battery Electric Vehicle (BEV) seems promising.However, there is currently a strong debate whether Fuel Cell Electric Vehicle (FCEV) might be the bettersolution. The question arises as to how a fleet of FCEV influences the operating cost, the Greenhouse Gas(GHG) emissions and primary energy demand in comparison to BEVs and to Internal Combustion EngineVehicle (ICEV). To investigate this, we simulate the urban food retailing as a representative share of urbanfreight transport using a multi-agent transport simulation software. Synthetic routes as well as fleet size andcomposition are determined by solving a Vehicle Routing Problem (VRP). We compute the operating costsusing a total cost of ownership (Total Cost of Ownership (TCO)) analysis and the use phase emissions as wellas primary energy demand using the Well To Wheel (WTW) approach. While a change to BEV results in 17 -23% higher costs compared to ICEV, using FCEVs leads to 22 - 57% higher costs. Assuming today’s electricitymix, we show a GHG emission reduction of 25% compared to the ICEV base case when using BEV. Currenthydrogen production leads to a GHG reduction of 33% when using FCEV which however cannot be scaled tolarger fleets. Using current electricity in electrolysis will increase GHG emission by 60% compared to the basecase. Assuming 100% renewable electricity for charging and hydrogen production, the reduction from FCEVsrises to 73% and from BEV to 92%. The primary energy requirement for BEV is in all cases lower and forhigher compared to the base case. We conclude that while FCEV have a slightly higher GHG savings potentialwith current hydrogen, BEV are the favored technology for urban freight transport from an economic andecological point of view, considering the increasing shares of renewable energies in the grid mix.

The influence of short term water absorption on the mechanical properties of halloysite nanotubes-multi layer graphene reinforced polyester hybrid nanocomposites has been investigated. The addition of nano-fillers significantly increased the flexural strength; tensile strength and impact strength in dry and wet conditions. After short term water exposure; the maximum microhardness; tensile; flexural and impact toughness values were observed at 0.1 wt% MLG. The microhardness increased up to 50.3%; tensile strength increased up to 40% and flexural strength increased up to 44%. Compared to dry samples; the fracture toughness and surface roughness of all types of produced nanocomposites were increased that may be attributed to plasticization effect. Scanning electron microscopy revealed that the main failure mechanism is caused by the weakening of nano-filler-matrix interface induced by water absorption. It was further observed that synergistic effects were not effective at concentration of 0.1 wt% to produce considerable improvement in mechanical properties of produced hybrid nanocomposites.

The essence of cross-modal generation and retrieval modeling for image-text interactions lies in semantic consistency. Among these, cross-modal representation alignment serves as the foundational requirement for achieving cross-modal semantic consistency. The crux of our proposed method entails the collaborative training of an image captioning model(referred to as the ’captioner’) and a pair of contrastive encoders for image-text matching(referred to as the ’concoder’). This synergistic approach yields concurrent enhancements in concoder’s performance, captioner’s proficiency, and cross-modal semantic coherence. We coin the proposed method as ‘ReCap’. To begin, we initialize the concoder through knowledge distillation from a pre-trained model. During the training process, we use the output of the initialized concoder as input to a residual attention network, jointly training it with the captioner to achieve semantic consistency. Subsequently, we iteratively update the concoder during the image-text momentum encoding phase using the residual attention network, creating a closed-loop for semantic consistency resolution. Upon completion of training, the concoder and captioner modules can be used independently to perform tasks related to cross-modal retrieval and cross-modal generation of text and images. In order to substantiate the efficacy of our proposed method, we initially conducted empirical experiments encompassing image-text retrieval and image captioning tasks, employing a widely recognized benchmark dataset, MSCOCO. Subsequently, we assessed the fine-grained cross-modal alignment performance of the concoder through an image classification task on the iNaturalist 2018 dataset. The achieved performance metrics notably surpassed those achieved by several incumbent state-of-the-art models, thus validating the proficiency of our method. Finally, motivated by the practical requirements of handling the nature conservation image data, we performed caption annotation for the iNaturalist 2018 dataset. Subsequently, we trained the ReCap on this annotated data. Experimental results demonstrate that our proposed method can maintain semantic consistency between cross-modal retrieval and image caption generation for species with similar visual features but distinct semantics. This achievement signifies a meaningful exploration in the field of cross-modal semantic consistency representation, holding significant practical value in the domain of biological research.

The adoption of algorithms based on Artificial Intelligence (AI) has been rapidly increasing during the last years. However, some aspects of AI techniques are under heavy scrutiny. For instance, in many use cases, it is not clear whether the decisions of an algorithm are well-informed and conforming to human understanding. Having ways to address these concerns is crucial in many domains, especially whenever humans and intelligent (physical or virtual) agents must cooperate in a shared environment. In this paper, we introduce an application of an explainability method based on the creation of a Policy Graph (PG) based on discrete predicates that represent and explain a trained agent’s behaviour in a multi-agent cooperative environment. We show that from these policy graphs, policies for surrogate interpretable agents can be automatically generated. These policies can be used to measure the reliability of the explanations enabled by the PGs, through a fair behavioural comparison between the original opaque agent and the surrogate one. The contributions of this paper represent the first application of policy graphs in the context of explaining agent behaviour in collaborative multi-agent scenarios and presents experimental results that sets this kind of scenario apart from previous application in single-agent scenarios: when requiring collaborative behaviour, predicates that allow representing observations about the other agents are crucial to replicate the opaque agent’s behaviour and increase the reliability of explanations.

Autonomous navigation in dynamic environments presents a significant challenge for mobile robotic systems. In this paper, we propose a novel approach utilizing Convolutional Neural Networks (CNNs) for multi-object detection in 3D space and 2D segmentation using Bird’s Eye View (BEV) maps derived from 3D LiDAR data. Our method aims to enable mobile robots to localize movable objects and their occupancy, crucial for safe and efficient navigation. To address the scarcity of labeled real-world datasets, a synthetic dataset based on simulation environment is generated to train and evaluate our model. Additionally, we employ a subset of the NVIDIA r2b dataset for evaluation in real-world. Furthermore, we integrate our CNN-based detection and segmentation model into a ROS2-based framework, facilitating communication between mobile robots and a centralized node for data aggregation and map creation. Our experimental results demonstrate promising performance, showcasing the potential applicability of our approach in future assembly systems. While further validation with real-world data is warranted, our work contributes to the advancement of perception systems by proposing a solution for multi-source multi-object tracking and mapping.

The rapid increase in unstructured data across various fields has made multi-document comprehension and summarization a critical task. Traditional approaches often fail to capture relevant context, maintain logical consistency, and extract essential information from lengthy documents. This paper explores the use of Long-context Large Language Models (LLMs) for multi-document summarization, demonstrating their exceptional capacity to grasp extensive connections, provide cohesive summaries, and adapt to various industry domains and integration with enterprise applications/systems. The paper discusses the workflow of multi-document summarization for effectively deploying long-context LLMs, supported by case studies in legal applications, enterprise functions such as HR, finance, and sourcing, as well as in the medical and news domains. These case studies show notable enhancements in both efficiency and accuracy. Technical obstacles, such as dataset diversity, model scalability, and ethical considerations like bias mitigation and factual accuracy, are carefully analyzed. Prospective research avenues are suggested to augment the functionalities and applications of long-context LLMs, establishing them as pivotal tools for transforming information processing across diverse sectors and enterprise applications.

The splitting method developed in a previous study for linear, multi – component, convection-diffusion mass transfer equations is extended to non-linear, multi-component, convection-diffusion mass transfer equations. The diffusion term is non-linear (the diffusion coefficients depend on chemical species concentrations). Theoretical results about the splitting error are presented, as well as numerical simulations for mixtures with n ≤ 5. The numerical experiments show second-order accuracy and stability for the present splitting algorithm.

The optimization of the production process of metal mines has been traditionally driven only by economic benefits while ignoring resource efficiency. However, it has become increasingly aware of the importance of resource efficiency since mineral resource reserves continue to decrease while the demand continues to grow. To better utilize the mineral resources for sustainable development, this paper proposes a multi-objective optimization model of the production process of metal mines considering both economic benefits and resource efficiency. Specifically, the goals of the proposed model are to maximize the profit and resource utilization rate. Then, the fast and elitist Non-Dominated Sorting Genetic Algorithm (NSGA-II) is used to optimize the multi-objective optimization model. The proposed model has been applied to the optimization of the production process of a stage in the Huogeqi Copper Mine. The optimization results provide a set of Pareto-optimal solutions that can meet varying needs of decision makers. Moreover, compared with those of the current production indicators, the profit and resource utilization rate of some points in the optimization results can increase respectively by 2.99% and 2.64%. Additionally, the effects of the decision variables (geological cut-off grade, minimum industrial grade and loss ratio) on objective functions (profit and resource utilization rate) were discussed using variance analysis. The sensitivities of the Pareto-optimal solutions to the unit copper concentrate price were studied. The results show that the Pareto-optimal solutions at higher profits (with lower resource utilization rates) are more sensitive to the unit copper concentrate prices than those obtained in regions with lower profits.

This research centres on advancing the utilisation of a novel Deep Ensemble model called RicEns-Net for predicting crop yields through sophisticated multi-modal data engineering. Initially, data for the study were acquired from Ernst \& Young (EY), a prominent global technology and management consulting firm, as part of their annual data science challenge (EY Open Science Challenge 2023). The predictive models leverage multi-modal data by integrating radar and optical-type remote sensing data alongside meteorological data to create supplementary features essential for predicting crop yield. The primary data features are derived from spectral indices extracted from Sentinel 2 satellites, while more advanced features are generated through combinations and interactions of these fundamental features. Furthermore, data from Sentinel 1 and 3, along with meteorological measurements such as surface temperature and rainfall, account for the intricate natural factors influencing crop yield, creating a comprehensive set of data features based on existing research. To tackle the complexity introduced by numerous data features, extensive data engineering was conducted to identify the most predictive features among 100+ and mitigate the "curse of dimensionality," resulting in 15 features from 5 different modalities. The proposed RicEns-Net comprises multiple machine learning algorithms in a deep ensemble approach to leverage the best features of each of these techniques, achieving optimal performance. The proposed model achieves an MAE value of 341 kg/Ha for prediction, surpassing the performance of the EY Open Science Challenge 2023 winner models and state-of-the-art deep/machine learning approaches.

This paper is devoted to the study of multi-dimensional integral transform with Fox H-function in the kernel in weighted spaces integrable functions in the domain R+n with positive coordinates. Mapping properties such as the boundedness, the range, the representations of the considered transformation are established.

Agriculture uses a lot of fuel, fertilizers, pesticides and other substances, while emitting large amounts of GHGs. It is important to optimize these inputs and outputs. One such way is increas-ing crop biodiversity. For this reason, single crops and mixtures of maize, hemp and faba bean as binary and ternary crops were investigated at the Experimental Station of Vytautas Magnus Uni-versity, Lithuania. Results showed that consumption of diesel fuel was by the 31-46% higher than in single and 22-35% higher than in binary cultivations was found in a ternary crop. This influenced on the highest energy input or near twice higher than in maize and hemp single crops and maize+hemp binary crop, but similar with binary crops with faba bean. Despite this, the productivity of the trinary crop and, at the same time, the energy output were 2-5 times higher than in other treat-ments. This compensated for higher energy inputs and the energy efficiency ratio. In ternary crop, energy productivity was from 1.1 to 2.8 times higher and net energy was by 1.9-5.3 times higher than in other tested cultivations. The highest total GHG emissions were obtained in binary maize+hemp and maize+faba bean cultivations (1729.84 and 2067.33 CO2eq ha-1). Ternary cultiva-tion with the highest energy inputs initiated average GHG emission - 1541.90 kg ha-1 CO2eq. For higher efficiency, ternary crop could be sown and harvested in one machine pass. Faba beans should be included in the ter-nary crops, as their biomass takes a significant part of the total biomass produced. We recommend to review the inter-cropped faba bean seeding rates as faba bean seeds have a high energy input equivalent.

: Polymer single screw extrusion is a major industrial processing technique used to obtain plastics products. To assure high outputs, tight dimensional tolerances, and excellent product performance, extruder screws may show different design characteristics. Barrier screws, which contain a second flight in the compression zone, have become quite popular as they promote and stabilize polymer melting. Therefore, it is important to design efficiently extruder screws and decide whether a conventional screw will do the job efficiently, or a barrier-screw should be considered instead. This work uses multi-objective evolutionary algorithms to design conventional and barrier screws (Maillefer screws will be studied) with optimized geometry. Processing of two polymers, Low Density Polyethylene and Polypropylene, is analyzed. A methodology based on the use of Artificial Intelligence (AI) techniques, namely data mining, decision making and evolutionary algorithms, is presented and utilized to obtain results with practical significance, based on relevant performance measures (objectives) used in the optimization. For the various case studies selected, Maillefer screws were generally advantageous for processing LDPE, while for PP the use of both types of screws would be feasible.

Bayesian techniques for engineering problems, that rely on Gaussian process (GP) regression, are known for their ability to quantify epistemic and aleatory uncertainties and for being data efficient. The mathematical elegance of applying these methods usually comes at a high computational cost when compared to deterministic and empirical Bayesian methods. Furthermore, using these methods becomes practically infeasible in scenarios characterized by a large number of inputs and thousands of training data. The focus of this work is on enhancing Gaussian Process-based metamodeling and model calibration tasks, when the size of the training datasets is significantly large. To achieve this goal, we employ a stochastic variational inference algorithm that enables rapid statistical learning of the calibration parameters and hyperparameter tuning, while retaining the rigor of Bayesian inference. The numerical performance of the algorithm is demonstrated on multiple metamodeling and model calibration problems with thousands of training data.

Multi-rotor drones, a kind of unmanned equipment which is widely used in military, commercial consumption and other fields, has been developed very rapidly in recent years. However, their short flight time has hindered the expansion of their application range. This can be addressed by utilizing hydrogen fuel cells, which exhibit high energy density, strong adaptability to ambient temperature, and no pollution emissions, as the power source. Accordingly, the application of hydrogen fuel cells as the power source in multi-rotor drones is a promising technology that has attracted significant research attention. This paper summarizes the development process of hydrogen fuel cell mul-ti-rotor drones and analyzes the key obstacles that need to be addressed for the further development of hydrogen fuel cell multi-rotor drones, including structural lightweight, hydrogen storage methods, energy management strategies. Additionally, prospects for the future development of hydrogen fuel cell multi-rotor drones are presented.

Fabry-Pérto (FP) cavity is the essential component of ultra-stable laser (USL) for gravitational wave detection, which couples multi-physic (Optical/Thermal/Mechanics) fields and requires ultra-high precision. To satisfy the requirements of precise and efficient design, a multi-physic coupling optimization method for fixing cubic FP cavity based on data learning is proposed. A multi-physic model for the cubic FP cavity is established and the performance is obtained by finite element analysis. The key performance indices (V, wF, wF) and key design variables (d, l, F) are determined considering the features of the FP cavity. The 49 sets of data by orthogonal experiment are acquired for the establishment and comparison of different data learning models (NN, RSF, KRG). The result turns out that the neural network has the best performance. Based on NSGA-II, the Pareto optimal front is obtained and the optimal combination of design variables is finally determined as {5,32,250}. The performance after optimization has proven to be a great improvement, of which the displacement under the fixing force and vibration test are decreased by more than 60%. The optimization strategy can not only help the design of the FP cavity but also enlighten other optimization fields.

This study aims to develop a performance evaluation system that can facilitate performance evaluation at region, hospital, and department levels to enable better cost management for sustainable development. A multi-level system of performance evaluation informs a hierarchical assessment of cost management from regions to hospitals to departments using diagnosis-related group (DRGs). Various metrics are developed employing the variances between targets and actuals where targets are determined from two perspectives: benchmarking using external regional prices and change management using internal data. Targets for the latter are statistically based and specifically incorporate variability. The model is applied to two hospitals, twenty departments, nine DRGs and 1071 inpatients. The analyses indicate that the approach can provide a practical evaluation tool that allows for particular characteristics at multiple levels. The system provides macro-micro and external-internal perspectives in performance, enabling high-level variances to be decomposed thereby identifying sources of performance variability and financial impact.

One of the fastest growing customer service delivery platforms is online banking. However, the increasing number of attacks on online banking platforms is driving the banks to constantly review their security. This study developed an enhanced Multi-factor authentication scheme with a track and trace capability to reduce these threats. Five modalities of authentication were incorporated in the proposed scheme: The traditional username, password, personal identification number (PIN) and one-time PIN (OTP), augmented with fingerprints or facial scans, registered smart devices, and a time locked user's location. One of the scheme's most impressive accomplishments is its capacity to seamlessly detect undesired activities and send alerts in the form of secretly obtained photographs and location triangulation.

Due to a shortage of funding and other market challenges, Small and Medium-sized Enterprises (SMEs) have a tough time adopting new technologies. Numerous technological obstacles nega-tively impact the long-term commercial achievement of SMEs. The deployment of Industry 4.0 might resolve several technological challenges. A sustainable city is a difficult structure whose economical, societal, and ecological components interact and compete with one another. There is a dearth of actual methodologies for measuring interaction. The objective of Industry 4.0 is to obtain a better degree of performance effectiveness and profitability, and greater automation. Conse-quently, the purpose of the research is to determine the influence of Industry 4.0 in fostering economic efficiency in small and medium enterprises' sustainability. A Sustainable City using Multi-Criteria Decision Making (SC-MCDM) system is designed in this research to test and achieve sustainable developmental goals. This paper then gives a technique for calculating the interaction between various standards, such as static interactions and dynamical pattern resemblance, as well as the weight variables of every indication generated by the connection. Furthermore, the ap-plication of the suggested technique is proved by assessing the sustainable development goals of twelve Chinese cities within the Triple Bottom Line (TBL) paradigm. From a geographic-temporal viewpoint, spatial variations in city sustainability reveal regional inequalities in sustainability. Indicator scores suggest that the lack of research spending, falling financing in stationary assets, shortage of financial development, and inadequate shared transit are the most significant limiting factors for most communities. Furthermore, the growth of tertiary industries, the improvement of energy performance, the expansion of green areas, and the reduction of pollution emissions are the key driving forces for enhancing sustainability. Compared to other methodologies, Multi-Criteria Decision Making (MCDM) considers the interplay between conditions, which is an excellent way to assess the sustainability of a city. The experimental findings show the impact of MCDM and sustainability to achieve sustainable development goals.

In order to perform multi-degree-of-freedom motion measurements of marine machinery such as ship-borne mechanical platform in an absolute environment without a reference, absolute measurement methods using acceleration sensors and tilt gyroscopes are typically employed. However, due to the influence of wave forces on ship-borne mechanical platform, the coupling between different degrees of freedom can cause mutual interference, resulting in significant sensor measurement disturbances that make efficient computation and real-time analysis challenging. Specifically, when ship-borne mechanical platform swings, the proof mass of the acceleration sensor produces an undesirable signal output in the vertical direction, which leads to imprecise acceleration integration, thereby affecting accurate motion collection and posture estimation. To address these challenges, by analyzing the influence of the inclination angle of the ship-borne mechanical platform on the sensor measurement, and using the working principle of the acceleration sensor and angle sensor, a correction method for the motion measurement of the ship-borne mechanical platform based on multi-sensor fusion is proposed. In this article, we first analyze the influence of inclination angle on the integral effect in the heave direction. Then the configuration using four groups of acceleration sensors to correct the integral effect is proposed. Finally, the optimal inclination angle is determined through Kalman filtering based on the measured value of angle sensors and estimated values from the acceleration sensor sets. Experiments have proved that the average error of the corrected heave displacement signal is 25.34 mm, which is better than the integral displacement signal of a single acceleration sensor. At the same time, the acceleration sensor is used to calculate the roll angle and pitch angle of the ship-borne mechanical platform, and combined with the angle sensor signal to perform Kalman filtering, which filters out the errors caused by the shaking and instability of the mechanical platform, and can more accurately estimate the true inclination of the platform. Therefore, this method can enhance the precision and accuracy of the ship-borne mechanical platform motion signal acquisition, providing more valuable experimental data for research in marine engineering and related fields.

This paper proposes an optimization method for the scheduling of a multi-energy virtual power plant supply-demand balance in the power market environment of Jiangxi Province. The objective of this method is to enhance the operational efficiency of the power grid, reduce energy costs, and facilitate economical and efficient energy distribution in the power market. The method comprehensively considers the characteristics and uncertainties of renewable energy sources such as solar and wind energy, and incorporates advanced multi-objective optimization algorithms. Additionally, real-time market price feedback is integrated to achieve accurate allocation of power supply and demand. Through a case study of a multi-energy virtual power plant in Jiangxi Province, this paper examines the optimal combination model for various energy sources within VPP, and analyzes the impact of different market environments on supply-demand balance. The results demonstrate that the proposed scheduling optimization method significantly improves economic benefits while ensuring grid stability. Compared with traditional power supply models, it reduces average electricity costs by 15% and increases renewable energy utilization efficiency by 20%.

The optimization of guide vane closing schemes (OGVCS) of pumped storage hydro unit (PSHU) is the research field of cooperative control and optimal operation of pumped storage, wind power and solar power generation. This paper presents a OGVCS model of PSHU considering the rise rate of the unit rotational speed and the specific node pressure of each hydraulic unit, as well as various complicated hydraulic and mechanical constraints. OGVCS model is formulated as a multi-objective optimization problem to optimize conflictive objectives, i.e., unit rotational speed and water hammer pressure criteria. In order to realize the efficient solution of the OGVCS model, an enhanced multi-objective bacterial-foraging chemotaxis gravitational search algorithm (EMOBCGSA) is proposed to solve this problem, which adopts population reconstruction, adaptive selection chemotaxis operator of local searching strategy and Elite archive set to efficiently solve the multi-objective problem. Especially, novel constraints-handling strategy with eliminating and local search based on violation ranking is used to balance various hydraulic and mechanical constraints. Finally, simulation cases of complex extreme operating conditions (i.e., load rejection and pump outage) of ‘single tube-double units’ type PSHU system are conducted to verify the feasibility and effectiveness of the proposed EMOBCGSA in solving OGVCS problem. The simulation results indicate that the proposed EMOBCGSA can provide lower rise rate of the unit rotational speed and smaller water hammer pressure than other method established recently while considering various complex constraints in OGVCS problem.

A Wireless Body Area Sensor Network (WBASN) is combination of numerous sense nodes, positioned onto/close or inside a person body. Wireless Body Area Sensor Networks (WBASN) is a developing automation trend that exploits wireless sensor nodes to put instantaneous wearable well-being of ill person to improve individual’s existence. The sensor nodes might be used outwardly to observe abundant health parameters (like heart activity, blood pressure and cholesterol) of an ill person at a vital site within hospital. Hence the goal of WBASN is much crucial, enhancing the lifetime of nodes is compulsory to sustain many issues such as utility and efficiency. It is essential to evaluate time that when the first node will die it we want to refresh or change the battery reason is that loss of crucial information is not tolerable. The lifetime is termed as the time interval when a first node dies out due to battery exhaustion. In our proposed protocol life time of a network is the main concern as well other protocol related issues such as throughput, path loss, and residual energy. Bio-sensors are used for deployment on human body. Poisson distribution and equilibrium model techniques have been used for attaining the required results. Multi-hop network topology and random network node deployment used to achieve minimum energy consumption and longer network lifetime.

The eutrophication of open water bodies, especially in coastal water area, has received intensive public focuses in recent years. Biological treatment of organic pollutants in industrial and domestic wastewater requires microbial flora to participate. The environmental impact of these microbes, particularly in regard to the spread of antibiotic resistance genes and pathogenicity in coastal water, remains largely unknown. We initiate studies to examine antibiotic resistance genes (ARGs) in microbial flora and study the mode of antibiotic spread in the coastal waters of Bohai Bay, North China by using high performance liquid chromatography-mass spectrum analysis and quantitative polymerase chain reaction. The metabolic features of bacteria related to the presence of ARGs in the coastal area showed the enrichment of Pseudomonadale species with triple resistance properties (ampicillin, kanamycin and gentamycin) at the estuary site locating adjacent to a coastal sewage treatment plant where both type I and type II polyketide synthase genes and b-lactam type antibiotics are detected. Pseudomonadale order is phylogenetically belonged to Proteobacteria Phylum, Gamma-proteobacteria Class and contains Pseudomonadaceae family and Pseudomonas genus. QPCR analysis suggests that the percent occupation of Pseudomonadale species to total Proteobacteria in the examined stations is close to several sampling stations close to sewage treatment plants, where consistent release of organic wastes occurred.

The need to understand the process by which particles, including solar wind and coronal ions as well as pickup ions, are accelerated to high energies (ultimately to become anomalous cosmic rays) motivate a multi-fluid shock wave model which includes kinetic effects (e.g. ion acceleration) in an electromagnetically self-consistent framework. Particle reflection at the cross-shock potential leads to ion acceleration in the motional electric field and thus anisotropic heating and pressure in the shock layer, with important consequences for the multi-fluid dynamics. This motivates development of a multi-fluid model of solar wind electrons and ions treated as fluid, coupled self-consistently with a small population of kinetically treated ions (e.g. pickup ions.) Consideration of both the time dependent and steady state regimes, indicate that such a multi-fluid approach is necessary for resolving the, Debye scale, particle reflecting cross-shock potential and subsequent dynamics. To study charge separation effects in narrow, supersonic wave layers we consider a reduction of the system to the steady state for cold ions and hot electrons and find two types of solitary waves inherent to the reduced two-fluid system in this limiting case.

This paper presents a multi-swarm PSO algorithm for the Quadratic Assignment Problem (QAP) implemented on the OpenCL platform. Our work was motivated by results of time efficiency tests performed for single-swarm algorithm implementation that showed clearly that the benefits of a parallel execution platform can be fully exploited provided the processed population is large. The described algorithm can be executed in two modes: with independent swarms or with migration. We discuss the algorithm construction as well as we report results of tests performed on several problem instances from the QAPLIB library. During the experiments the algorithm was configured to process large populations. This allowed us to collect statistical data related to values of goal function reached by individual particles. We use them to demonstrate on two test cases that although single particles seem to behave chaotically during the optimization process, when the whole population is analyzed, the probability that a particle will select a near-optimal solution grows.

Surface damage on honeycomb aircraft panels is often measured manually, and is therefore subject to variation based on inspection personnel. Eddy current testing (ECT) is sensitive to variations in probe-to-specimen spacing, or lift-off, and is thus promising for high resolution profiling of surface damage on aluminum panels. Lower frequency testing also allows inspection through the face sheet, an advantage over optical 3D scanning methods. This paper presents results from the ECT inspection of surface damage on an approximately flat aluminum honeycomb aircraft panel, and compares the measurements to those taken using optical 3D scanning technology. An ECT C-Scan of the dented panel surface was obtained by attaching the probe to a robotic scanning apparatus. Data was taken simultaneously at four frequencies of 25, 100, 400 and 1,600 kHz. A reference surface was then defined that approximated the original, undamaged panel surface, which also compensated for the effects of specimen tilt and thermal drift within the ECT instrument. Data was converted to lift-off using height calibration curves developed for each probe frequency. A damage region of 22,550 mm² area with dents ranging in depth from 0.13-1.01 mm was analyzed. The method was accurate at 1,600 kHz to within 0.05 mm (2s) when compared with 231 measurements taken via optical 3D scanning. Testing at 25 kHz revealed a 3.2 mm cell size within the honeycomb core, which was confirmed via destructive evaluation. As a result, ECT demonstrates potential for implementation as a method for rapid in-field aircraft panel surface damage assessment.

This paper represents the first investigation into the consensus problem of linear time-varying multi-agent systems utilizing an event-triggered communication scheme. First, a general event-triggered consensus control scheme is proposed for a general category of linear time-varying multi-agent systems. Under some suitable assumptions, it is demonstrated that all agents’ states will converge exponentially, with Zeno behaviour being ruled out. Second, the consensus problem in a network of linear time-varying multi-agent systems with a spanning tree is investigated using the proposed control strategy. It demonstrates that the consensus issue for the specified system can be reformulated as a stabilization problem for an error system through a time-varying linear transformation. Then, the event-triggered consensus problem is just a special instance of the general event-triggered consensus problem mentioned above. Finally, to illustrate the efficacy of the event-triggered method proposed in this study, simulation results are shown.

Interferometric synthetic aperture radar (InSAR) and tomographic SAR measurement techniques are commonly used for the three-dimensional (3D) reconstruction of complex areas, while the effectiveness of these methods relies on the interferometric coherence among SAR images with minimal angular disparities. Radargrammetry exploits stereo image matching to determine the spatial coordinates of corresponding points in two SAR images, and acquire their 3D properties. The performance of the image matching process directly impacts the quality of the resulting digital surface model (DSM). However, the presence of speckle noise, along with dissimilar geometric and radiometric distortions, poses considerable challenges to achieve accurate stereo SAR image matching. To address the aforementioned challenges, this paper proposes a radargrammetric method based on composite registration of multi-aspect SAR images. The proposed method combines coarse registration using scale invariant feature transform (SIFT) with precise registration using normalized cross-correlation (NCC) to achieve accurate registration between multi-aspect SAR images with large disparities. Furthermore, the multi-aspect 3D point clouds are merged by the proposed radargrammetric 3D imaging method, resulting in 3D imaging of target scenes based on multi-aspect SAR images. For validation purpose, this paper presents a comprehensive 3D reconstruction of the Five-hundred-meter Aperture Spherical radio Telescope (FAST) by using Ka-band airborne SAR images. It does not necessitate prior knowledge of the target and is applicable to the detailed 3D imaging of large-scale areas with complex structures. In comparison to other SAR 3D imaging techniques, it reduces the requirements for orbit control and radar system parameters. To sum up, the proposed 3D imaging method with composite registration guarantees imaging efficiency while enhances the imaging accuracy of crucial areas with limited data.

Current global commitments to reduce emissions of greenhouse gases encourage national targets for renewable generation. Due to its small land mass, offshore wind could help Bahrain to fulfill its obligations. However, no scoping study has yet been carried out. The methodology presented here addresses this research need. It employs Analytical Hierarchy Process and pairwise comparison methods in a Geographical Information Systems environment. Publicly available land use, infrastructure and transport data are used to exclude areas unsuitable for development due to physical and safety constraints. Meteorological and oceanic opportunities are ranked, then competing uses are analyzed to deliver optimal sites for wind farms. The potential annual wind energy yield is calculated by dividing the sum of optimal areas by a suitable turbine footprint, to deliver maximum turbine number. Ten favourable wind farm areas were identified in Bahrain’s territorial waters, representing about 4% of the total maritime area, and capable of supplying 2.68 TWh/yr of wind energy or almost 10% of the Kingdom’s annual electricity consumption. Detailed maps of potential sites for offshore wind construction are provided in the paper, giving an initial plan for installation in these locations.

Electric vehicles (EVs) play a significant role in reducing carbon emissions. In the US, EVs are mostly owned by multi-vehicle households, and their usage is primarily studied in the context of vehicle miles traveled. This study takes a unique approach by analyzing EV usage through the lens of vehicle choice (between EVs and internal combustion engine vehicles) within multi-vehicle households. A two-step machine-learning framework (clustering and decision trees) is proposed. The framework determines the preferred trip category for EV use and captures the effects of household attributes, driver attributes, built-environment factors, and gas prices on EV use in multi-vehicle households. Results indicate that discretionary trips (accumulated local effect = 0.037) are mostly preferred for EV use. EV preference is more pronounced among households with fewer workers (<2) and lower income levels. These findings are valuable for policymakers and auto manufacturers in targeting specific market segments and promoting EV adoption.

With the every passing day, the demand for data traffic is increasing and this demand forces the research community not only to look for alternating spectrum for communication but also urges the radio frequency planners to use the existing spectrum smartly. Cell size is shrinking with the every upcoming communication generation which makes the base station placement planning complex and cumbersome. In order to make the next-generation cost-effective, it is important to design the network in such a way which utilizes minimum number of base stations while ensure coverage and quality of service. This paper aims at develop a new approach using hybrid metaheuristic and metamodel applied in multi-transmitter placement planning (MTPP) problem. We apply radial basis function (RBF) metamodel to assist particle swarm optimizer (PSO) in a constrained simulation-optimization (SO) of MTPP to mitigate the associated computational burden of optimization procedure. We evaluate the effectiveness and applicability of proposed algorithm in a case study by simulating MTPP model with two, three, four and five transmitters.

This article addresses the complex challenge of simultaneously enhancing contrast and detail in an image, where improving one property often compromises the other. This trade-off is tackled using a multi-objective optimization approach. Specifically, the proposal's model integrates the sigmoid transformation function and unsharp masking highboost filtering with the NSGA-II algorithm. Additionally, a posterior preference articulation is introduced to select three key solutions from the Pareto front: the maximum contrast solution, the maximum detail solution, and the knee point solution. The proposed technique is evaluated on a range of image types, including medical and natural scenes. The final solutions demonstrated significant superiority in terms of contrast and detail compared to the original images. The three selected solutions, although all are optimal, captured distinct characteristics within the images, offering different solutions according to field preferences. This highlights the method's effectiveness across different types and enhancement requirements and emphasizes the importance of the proposed preferences in different contexts.

In this paper, modelling, simulation and verification of multi-agent manufacturing system with application of bio-inspired techniques are addressed. To this end, the new solution of abstract architecture for control and coordination decentralized systems - CODESA is suggested. Centralized architecture suffers from various problems, such as rigidity, scalability, low fault-tolerance or very limited flexibility, agility, energy efficiency and productivity. Prime is concrete application of CODESA in manufacturing domain. The undesirable characteristics of emergent behaviour are the problem to achieve optimization and impossibility to predict future states of the system. CODESA-Prime has been tested by simulations for automatic guided vehicle (AGV) systems guided by magnetic tape in Ella Software Platform.

This paper investigates the leader-following H∞ consensus of fractional-order multi-agent systems (FOMASs) under input saturation via the output feedback. Based on the bounded real lemma for FOSs, the sufficient conditions of H∞ consensus for FOMASs are provided in α∈0,1 and 1,2, respectively. Furthermore, the iterative linear matrix inequalities (ILMIs) approaches are applied for solving quadratic matrix inequalities (QMIs). The ILMI algorithms show a method to derive initial values and transform QMIs into LMIs. Mathematical tools are employed to transform the input saturation issue into optimal solution of LMIs for estimating stable regions. The ILMI algorithms avoid the conditional constraints on matrix variables during the LMIs construction and reduce conservatism. The approach does not disassemble the entire MASs by transformations to the Laplacian matrix, instead adopting a holistic analytical perspective to obtain gain matrices. In the end, numerical examples are conducted to validate the efficiency of the approach.

Abstract: The diffusion of competition under the coexistence of multi-generation products has become one of the important challenges faced by enterprises in their daily and sustainable operations. At the same time, the competition between different brands has intensified the difficulty and complexity of decision-making in the process of multi-generation product operation, Therefore, based on the Norton-Bass model diffusion process, this paper introduces two marketing variables, dynamic price and quality level, builds a multi-generation product diffusion model under the dual-brand competition, and analyzes the impact of the company's revenue on the launch time to market, pricing, quality or technical level. By using system dynamics (SD) method, From the perspective of strong brand and weak brand enterprises, the competition diffusion model is built and simulated. The simulation shows that: i) When enterprises have the same brand competitiveness, reducing the pricing level cannot obtain more revenue, but diminish the overall revenue of the industry; Raising the pricing level can get more revenue, but also improve the revenue of competitors. ii) When the competitive strength of enterprises is different, the strong brand tends to maintain a stable pricing on the basis of improving the quality level, or slightly raise the price. Weak brands tend to raise the pricing of new products significantly on the basis of improving the quality level. iii) The launch time to market decision of new product is influenced by the degree of product quality upgrade. Therefore, the frequency of releasing new products should trade-off against the degree of technological upgrading of product quality. This paper provides the theoretical basis and new insights for the new product launch and operation decision of enterprises.

Enhancing the effectiveness of search and rescue operation at sea is always a duty of utmost importance of the coastal states. The search area for distressed objects can be determined by using Monte Carlo simulation, combined with the Median-Filter. Once the search area has been identified, the success of search and rescue operations depends on the sweeping ability of search and rescue vessel at the probability area of the distress object with the minimum time. This is the important element to the success of the search and rescue operation as it minimizes the risk and cost for Search and rescue team. In this article, the authors study and propose the use of Bacterial Foraging Optimization Algorithm (BFOA) to calculate the optimal search and co-ordination route for many search and rescue vessels in Vietnam sea. The simulation results show that it is quite consistent with reality and BFOA can be effectively applied to determine a quick search.

Wind turbines (WTs) are clean a renewable energy source that has been growing in popularity in recent years. Gearboxes are complex, expensive, and critical components of WT, which are subject to high maintenance costs and several stresses including high loads and harsh environments that can lead to failure with significant downtime and financial losses. This paper focuses on the development of a digital twin-based approach for the modelling and simulation of WT gearboxes with the aim to improve their design, diagnosis, operation, and maintenance by providing insights into their behavior under different operating conditions. Pow-erful commercial computer-aided design tools (CAD) and computer-aided engineering (CAE) software are embedded into a computationally efficient multi-objective optimization framework (modeFrontier) with the aim of maximizing the power density, compactness, performance, and reliability of the WT gearbox. This entails minimizing its weight, volume, and maximum stresses and strains achieved without compromising efficiency. The 3D CAD model of the WT gearbox is carried out using SolidWorks, the Finite Element Analysis (FEA) to obtain the stresses and strains fields are modelled using Ansys Workbench, while the multibody kinematic and dynamic system is analyzed using MSC Adams. The method has been successfully applied to different case studies to find the optimal design and analyze the performance of the WT gearboxes. Simulation results can be used to identify potential failure modes and optimize gearbox design to improve performance, extend service life and relia-bility, thereby ensuring proper operation over its lifetime and reducing maintenance costs.

In response to reducing the energy cost of unmanned surface vehicles (USVs) while overcoming the low accuracy problem in surface target detection, a lightweight detection algorithm with multi-scale feature fusion is proposed. Based on the popular one-stage lightweight Yolov7-tiny target detection model, a lightweight extraction module is designed first by introducing the multiscale residual module to reduce the number of parameters and computational complexity while improving accuracy. The Mish and SiLU activation functions are used to enhance network feature extraction. Second, the path aggregation network employs coordinate convolution to strengthen spatial information perception. Finally, the dynamic head, which is based on the at-tention mechanism, improves the representation ability of object detection heads without any computational overhead. According to the experimental findings, the proposed model has 22.1% fewer parameters than the original model, 15% fewer GFLOPs, a 6.2% improvement in mAP@0.5, a 4.3% rise in mAP@0.5:0.95, and it satisfies the real-time criteria. According to the research, the suggested lightweight water surface detection approach includes a lighter model, a simpler computational architecture, more accuracy, and a wide range of generalizability. It performs bet-ter in a variety of difficult water surface circumstances.

Based on the topology of wide area protection system (WAPS), after studying the reliability of hardware system and information flow in the WAPS and establishing the reliability assessment model, the multi-service reliability analysis method with multi monitoring and protection tasks in WAPS was proposed. In the model, the impact of network quality of service (QoS) such as information flow loss and delay, is studied. On the base of the model, the multi-service reliability evaluation method is employed to analyze the reliability of a WAPS of IEEE14 node power system, and the key nodes of the WAPS is given, which provides a basis for improving the reliability of the WAPS.

This paper presents the design and implementation of a digital control system for modular multilevel converters (MMC) and its use in a 5-kW small scale prototype. To achieve higher system control reliability and multi-functionality, the proposed architecture has been built with an effective split of the control tasks between a master controller and six slave controllers, one for each of the six arms of the converter. The MMC prototype have been used for testing both converter and system level controls in a reduced scale laboratory set up of a Multi-Terminal DC transmission network (MTDC). The whole control has been tested in order to validate the proposed control strategies. The tests performed at system level allowed to explore the advantages of using an MMC in a MTDC system.

In the paper, the author introduces the notions "multi-order logarithmic numbers" and "multi-order logarithmic polynomials", establishes an explicit formula, an identity, and two recurrence relations by virtue of the Faa di Bruno formula and two identities of the Bell polynomials of the second kind in terms of the Stirling numbers of the first and second kinds, and constructs some determinantal inequalities, product inequalities, logarithmic convexity for multi-order logarithmic numbers and polynomials by virtue of some properties of completely monotonic functions.

Using traditional methods based on detection rules written by human security experts, there is a significant challenge in accurately detecting many network threats that are increasingly becoming sophisticated. In order to deal with the limitation of the traditional methods, network threat detection techniques utilizing artificial intelligence technologies such as machine learning are being extensively studied. Research has also been conducted on analyzing various string patterns in network packet payloads through natural language processing techniques to detect attack intent. However, due to the nature of packet payloads containing binary data as well as text data, a new approach is needed that goes beyond typical natural language processing techniques. In this paper, we study a token extraction method optimized for payloads using n-gram and byte pair encoding techniques. Furthermore, we generate embedding vectors that can understand the context of the packet payload using algorithms such as Word2Vec and FastText. We also compute the embedding of various header data associated with packets, such as IP addresses and ports. Given the combination of these features, we ensemble a text 1D-CNN and a multi-head attention network in a novel fashion. We validated the effectiveness of our classification technique with the CICIDS2017 open dataset and over half a million data collected by The Education Cyber Security Center (ECSC) currently operating in South Korea. The proposed model showed remarkable progress compared to previous studies, demonstrating a highly accurate classification performance with an F1-Score of 0.998. Our model can also preprocess and classify 150,000 network threats per minute to help security agents in the field divert their time to analyzing more complex attack patterns.

Internet of things (IoT) is a network of smart things. This indicates the ability of these physical things to transfer information with other physical things. IoT has introduced various services and daily human life depends on its reliable and accessible operation. The characteristics of these networks, such as topology dynamicity and energy constraint, challenges the routing problem in these networks. Previous routing methods could not achieve the required performance in this type of network. Therefore, developers of this network designed and developed specific methods in order to satisfy the requirements of these networks. One of the routing methods is utilization of multi-path protocols which send data to its destination using routs with separate links. One of such protocols is AOMDV routing protocol. AOMDV protocol is a multi-path protocol which uses multiple different paths for sending information in order to maintain the network traffic balance, manage and control node energy, decrease latency, etc. In this paper, this method is improved using gray system theory which chooses the best paths used for separate routes to send packets. To do this, AOMDV packet format is altered and some fields are added to it so that energy criteria, link expiration time, and signal to noise ratio can also be considered while selecting the best route. The proposed method named GSTMPR-IoT is introduced which chooses the routs with highest rank for concurrent transmission of data, using a specific routine based on the gray system theory. In order to evaluate and report the results, the proposed GSTMPR-IoT method is compared to the EECRP and AOMDV approaches with regard to throughput, packet delivery rate, end to end delay, average residual energy, and network lifetime. The results demonstrate the superior performance of the proposed GSTMPR-IoT compared to the EECRP and AOMDV approaches.

Inherited cardiomyopathies are a diverse group of heart muscle diseases caused by genetic mutations that result in structural and functional abnormalities of the myocardium. Understanding genotype-phenotype correlations in these conditions is vital for personalized cardiac medicine, enabling targeted therapeutic strategies and predictive diagnostics. This review explores the major types of inherited cardiomyopathies—hypertrophic cardiomyopathy (HCM), dilated cardiomyopathy (DCM), arrhythmogenic right ventricular cardiomyopathy (ARVC), and restrictive cardiomyopathy (RCM)—and provides detailed insights into how different genetic mutations manifest as clinical features. The integration of multi-omics approaches and advanced disease modeling techniques has enhanced our ability to dissect these correlations. The review also discusses the implications of these findings for personalized medicine, including tailored therapeutic strategies, predictive diagnostics, and future research directions.

Non-polio enteroviruses (NPEVs), namely coxsackieviruses (CV), echoviruses (E), enteroviruses (EV), and rhinoviruses (RV), are responsible for a wide variety of illnesses. Some infections can progress to life-threatening complications in children or immunocompromised patients. To date, no treatments have been approved. Several molecules have been evaluated through clinical trials without success. To overcome these failures, the multi-target directed ligand (MTDL) strategy can be applied to tackle enterovirus infections. This work analyzes clinical trials to highlight the best candidates and develops filters to apply to a selection for MTDL synthesis. We explicitly stated the methods used to answer the question: Which solution can fight NPEVs effectively? We note the originality and relevance of this proposal in relation to the state of the art in the enterovirus-inhibitors field. Several combinations are possible to broaden the antiviral spectrum and potency. We discuss data related to the virus and data related to each LEAD compound identified. Overall, this study proposes a perspective on different strategies to overcome issues identified in clinical trials and evaluate the “MTDL” potential to improve the efficiency of drugs synergistically, broaden the targeted, and reduce the adverse effects and drug design cost as well as limit the opportunity of drug-resistant viruses.

Single and multi-vehicle crashes are a significant issue that causes economic and social costs and has therefore gained attention. This study explored the factors associated with injury severity for both single- and multi-vehicle crashes using over 550,000 crash data points in Japan between 2019 and 2021. We identified the determinants of road infrastructure and traffic control while controlling for driver, vehicle, environmental, and accident characteristics by applying ordered logit and bias-reduced binomial regression models. Our findings are as follows. 1) Traffic control variables did not affect single-vehicle crashes. 2) Guardrails had a higher severity in both single-vehicle crashes and multi-vehicle crashes at intersections. 3) The impact of the centerline differed between intersections and non-intersections for multi-vehicle crashes.  These results of this study provide transportation agencies with important guidance as to the road infrastructure and transport control.

Based on the daily observation data of 2254 meteorological stations in China from 1961 to 2021 after homogenization and correction, the extreme value analysis method that combines relative threshold and absolute threshold was used to identify extreme climate events in the mainland of China, namely extreme high temperature, extreme low temperature, extreme drought, extreme precipitation and extreme typhoon events. The frequency and linear variation trends of individual extreme events in the past 60 years were investigated. On this basis, the multi extreme events composite risk grade index (MXCI) was constructed, which can objectively reflect the comprehensive characteristics of multi extreme climate events in different regions. The results show that the high value areas of MXCI were mainly located in Southeast China and Southwest China. The MXCI presented a decreasing trend in most of the western and southeastern regions of China, while an increasing trend from Southwest China to the south of Northeast China, due to the frequent occurrence of extreme high temperature, extreme drought and other extreme events in these regions.

Although different assessments and evaluations of Dual-Miller cycle performed, specified output power and thermal performance associated with engine determined. Besides, multi objective optimization of thermal efficiency, Ecological Coefficient of performance ( ) and Ecological function ( ) by the mean of NSGA-II technique and thermodynamic analysis performed. The Pareto optimal frontier obtaining the best optimum solution is chosen by fuzzy Bellman-Zadeh, LINMAP, and TOPSIS decision-making techniques. Based on the results, performances of dual-Miller cycles and their optimization are improved.

In this study we present a hybrid approach of ACO with fuzzy logic and clustering methods to solve multi-objective path planning problems in case of swarm USVs. This study aims to enhance the performance of ACO algorithm by integrating fuzzy logic in order to cope with the multiple contradicting objectives and generate quality solutions by in parallel identifying the mission areas of each USV to reach the desired targets. The objectives that are taken into account are the minimization of traveled distance and energy consumption, and the maximization of path smoothness. A comparative evaluation is conducted among ACO and fuzzy inference systems, Mamdani (ACO-M) and Takagi–Sugeno–Kang (ACO-TSK). The results showed that depending on the needs of the application, each methodology can contribute respectively. ACO-M generates better paths but ACO-TSK presents higher computation efficiency.

The performance of a small reconfigurable unmanned aerial vehicle (UAV) is evaluated, 1 combining a multidisciplinary approach in computational analysis of additive manufactured struc- 2 tures, fluid dynamics, and experiments. Reconfigurable UAVs promise cost savings and efficiency 3 without sacrificing performance, while demonstrating versatility to fulfill different military mission 4 profiles. The use of computational fluid dynamics (CFD) in UAV design produces higher accuracy 5 aerodynamic data, which is particularly important for complex aircraft concepts such as blended 6 wing bodies. To address challenges relating to anisotropic materials, the Tsai-Wu failure criterion is 7 applied to structural analysis, using CFD solutions as load inputs. Aerodynamic performance results 8 show the low-speed variant attains an endurance of 1 hour, 48 minutes, whereas for its high-speed 9 counterpart, it is 29 minutes at 66.7% higher cruise speed. Each variant serves different aspects of 10 small UAS deployment in combat, with low-speed envisioned for close surveillance, and high-speed 11 for incursions. Experimental and simulation results suggest room for design iteration, in wing area 12 and geometry adjustments. Structural simulations demonstrated the need for airframe improvements 13 in the low-speed configuration. This paper highlights the potential of reconfigurable UAVs to disrupt 14 the industry, advocating for further research and design improvements.

Immersion in salt-lake solution was adopted to periodically test the concrete chloride-ion diffusion coefficient. The regression analysis was also completed. Also investigated was the time-dependent law of concrete chloride-ion diffusion coefficient with time. The influence of chloride-ion concentration in solution, water-to-cement ratio, and corrosion time on the largeness and accumulation rate of the concrete chloride-ion diffusion coefficient was also analyzed. Test results show that the concrete chloride-ion diffusion coefficient gradually decreased with increasing time and increased with increasing chloride-ion concentration in a salt lake . Taking into account the influence of factors such as water–binder ratio, chloride-ion concentration, and time-varying characteristics, a multi-factor calculation model for the concrete chloride-ion diffusion coefficient was established. Combining the prediction results and the measured data reported in this paper, the effectiveness and applicability of the established concrete chloride-ion diffusion coefficient calculation model were compared and verified, and the durability design and service life of a concrete structure under cool chlorine were compared. The results of analysis provide important boundary conditions.

This study will lead to the development of a numerical data set that will assist in the design of Savonius wind turbines. A major objective of this study is to develop a better design for Savonius turbine blades in order to increase their torque coefficients, rotational speeds, and pressure coefficients. As part of the experimental design methodology, a full dataset was generated by simulating three-dimensional scale models utilizing computational fluid dynamics (CFD) simulations that were validated by wind tunnel data. This process is multi-objective optimization for optimizing turbine performance. The twist angle, aspect ratio, and overlap ratio are all important factors in determining the optimal torque and power coefficients. The group method of data handling (GMDH) algorithm was utilized to model objective functions based on input-output data. The Pareto fronts were plotted using polynomial models obtained from the evolutionary Pareto-based optimization approach (modified NSGA-II), and the optimal commercial points were determined using TOPSIS. A comparison of three- and two-objective optimization data revealed that two-objective optimization data lie within the boundaries of a three-objective optimization problem. The torque coefficient, rotational speed, and power coefficient are all improved by 13.74%, 0.071%, and 5.32%, respectively, using multi-objective optimization. As a result of the multi-objective optimization of the turbine, some significant characteristics of objective functions were discovered.

In recent years, land supply in Hong Kong has fallen sharply and fails to keep pace with the growth of population and number of households. Land shortage becomes urgent and dire. With the inadequate provision of residential land, housing supply is also adversely affected.Insufficient housing supply leads to surging property and rental price in the private market. According to the Rating and Valuation Department (RVD), the overall private domestic price index peaked in June 2017 at 336.1. Keen housing demand is also observed in the private rental market. RVD statistics showed that the domestic rental index also reached the peak at 183.6 in June 2017 and the vacancy rate of about 3.8% as at the end-2016, which is much lower than the average vacancy rate of 5% from 1996 to 2015 (Development Bureau, 2017).In addition, there is soaring housing demand in public housing. As at the end-December 2021, the average waiting time for general applicants was 5.7 years, which is nearly double of the Housing Authority’s target for providing the first flat offer to general applicants at around three years on average (Housing Authority, 2021). Identifying and securing sufficient land to meet both current and anticipated pressing housing demand becomes a key challenge of the government. In the light of this, the government has established a dedicated task force (Task Force on Land Supply) in September 2017 and appointed 30 professionals from different disciplines, such as planning, engineering, academia and think tank, to take a Marco-review on the land supply sources, look for feasible options as well as consider the pros and cons of various options. 18 land supply options were worked out for the public to make choices in the public engagement exercise. Among the 18 choices, the development area on the Periphery of Country Parks was regarded as one of the land supplies sources. This option does not only include the Hong Kong Housing Society’s studies on developing Two Pilot Areas on the Periphery of Tai Lam and Man On Shan Country Parks, but also include developing more areas on the periphery of Country Parks. The proposed option received overwhelming attention from the public and aroused debates in various perspectives. Its ecological value, recreational value, financial viability and even legitimacy were discussed. However, spatial analysis on the suitability of having residential development in Country Parks has not been conducted. Therefore, in this study, multi criteria GIS analysis is conducted to evaluate the geographic suitability of Hong Kong Country Parks for residential purpose with the consideration of various criteria.

Chemical and physical properties of nanoparticles (NPs) are strongly influenced not only by the crystal structure of the respective material including crystal structure defects, but also by the NP size and shape. Contemporary transmission electron microscopy (TEM) is capable of describing all of these NP characteristics, however typically with a different statistical relevance. While the size and shape of NPs are frequently determined on a large ensemble of NPs and thus with good statistics, the characteristics on the atomic scale are usually quantified for a small number of individual NPs and thus with a low statistical relevance. In this contribution, we present a TEM-based characterization technique, which is capable of determining relevant characteristics of NPs in a scale-bridging way – from the crystal structure and crystal structure defects up to the NP size and morphology – with a sufficient statistical relevance. This technique is based on a correlative multi-scale TEM approach that combines information on atomic scale obtained from the high-resolution imaging with the results of the low-resolution imaging assisted by a semi-automatic segmentation routine. The capability of the technique is illustrated on several examples including Au NPs having different shape, Au nanorods having different facet configurations and multi-core iron oxide nanoparticles having a hierarchical structure.

Steel damper columns (SDCs) are energy-dissipating members that are suitable for reinforced concrete (RC) moment-resisting frames (MRFs) and those often used for multistory housing. In a previous study, an energy-based prediction procedure for the peak and cumulative response of an RC frame building with SDCs was proposed. In this procedure, the accuracy of the equivalent velocity of the maximum momentary input energy (V_ΔE1^*)–peak equivalent displacement (D₁^*_max) relationship is essential for improved prediction. In this article, the seismic capacity curve (V_ΔE1^*–D₁^*_max relationship) of RC MRFs with and without SDCs is evaluated using incremental critical pseudo-multi impulse analysis (ICPMIA). In the ICPMIA, which is based on a study by Takewaki and coauthors, the structure is subjected to various intensities of critical pseudo-multi impulsive lateral force. An ICPMIA of four 8- and 16-story RC MRFs with and without SDCs is performed to obtain their structural behaviors under various intensities of pulsive input. Then, the seismic capacity curve obtained from the ICMPIA results are compared with the predicted results based on the simplified equations. The main findings of this article are as follows. (i) The seismic capacity curve of RC MRFs without SDCs strongly depends on the number of impulsive lateral forces (N_p). As N_p increases, the seismic capacity decreases. The predicted seismic capacity curve severely underestimates that obtained from the ICMPIA in the case of large N_p. This trend is notable when the level of pinching behavior in the RC members is severe. (ii) In the case of an RC MRF with SDCs, however, the influence of N_p on its seismic capacity curve is small. The predicted seismic capacity curve agrees very well with that obtained from the ICMPIA. The influence of the level of pinching behavior in RC members on the seismic capacity curve is small.

In recent years, distributed generation technology has developed rapidly. Renewable energy, represented by wind energy and solar energy, has been widely studied and utilized. In order to give full play to the advantages of Distributed Generation (DG) and meet the challenges after power grid access, Active Distribution Network (ADN) is considered as the future development direction of traditional distribution network because of its ability of active management. Nowadays, multi-scenario analysis is widely used in the research of optimal allocation of distributed power supply in active distribution network. Aiming at the problems that may arise when using multi-scenario analysis to plan DG with uncertainties in large-scale scenarios, a scenario reduction method based on improved clustering algorithm is proposed. The validity of the scene reduction method is tested, and the feasibility of the method is verified. At present, there are few studies on the optimal allocation of DG in ADN under fault state. In this paper, comprehensive safety indicators are introduced. Considering the timing characteristics of DG and the influence of active management mode, a bi-level programming model is established, which aims at minimizing the investment of annual life cycle and the removal of active power. The bi-level model is a complex mixed integer non-linear programming model. A hybrid algorithm combining cuckoo search algorithm and primal dual interior point method is used to solve the model. Finally, through the simulation of the IEEE-33 node system, the superiority of the scenario reduction method and the comprehensive security index used in this paper to optimize the configuration of DG in ADN is verified.

The presence of cracks reduces egg quality and safety, which are easy to cause food safety hazards to consumers. Machine vision-based methods for crack egg detection have made significant success on in-domain egg data. However, the performance of deep learning models usually decreases under practical industrial scenarios, such as the different egg varieties, origins, and environmental changes. Existing researches which rely on improving network structures or increasing training data volumes, can not effectively solve the problem of model performance decline on unknown egg testing data in practical egg production. To address these challenges, a novel and robust detection method is proposed to extract max domain-invariant features to enhance the model performance on unknown testing egg data. Firstly, multi-domain egg data is built on different egg origins and acquisition devices. Then, a multi-domain trained strategy is established by using Maximum Mean Discrepancy with Normalized Squared Feature Estimation (NSFE-MMD) to obtain the optimal matching egg training domain. With the NSFE-MMD method, the original deep learning model can be applied without network structure improvements, which reduces the extremely complex tuning process and hyperparameter adjustments. Finally, robust crack egg detection experiments are carried out on several unknown testing egg domains. The YOLOV5 model trained by proposed multi-domain trained method with NSFE-MMD has a detection mAP of 86.6\% on the unknown test domain 4, and the YOLOV8 model has a detection mAP of 88.8\% on domain 4, which is an increase of 8\% and 4.4\% compared to the best performance of models trained on a single domain, and an increase of 4.7\% and 3.7\% compared to models trained on all domains. In addition, the YOLOV5 model trained by the proposed multi-domain trained method has a detection mAP of 87.9\% on egg data of the unknown testing domain 5. The experimental results demonstrate the robustness and effectiveness of the proposed multi-domain trained method, which can be more suitable for the large quantity and variety of egg detection production.

Cancer cells display elevated reactive oxygen species (ROS) and altered redox status, Here based on these characteristics, we develop a multi-drug delivery platform AMB@PDAP-Fe (APPF), from magnetotactic bacterium AMB-1 and realize MRI-visualized tumor microenvironment-responsive photothermal-chemodynamic therapy. The Fe3+ in PDAP-Fe is reduced by the GSH at tumor site and is released in the form of highly active Fe2+, which catalyzes the generation of ROS through Fenton reaction and inhibits tumor growth. At the same time, the significant absorption of the mineralized magnetosomes in AMB-1 cells in the NIR region enable them to efficiently convert near-infrared light into heat energy for photothermal therapy (PTT), to which PDAP also contributes. The heat generated in the PTT process accelerates the process of Fe2+ release, thereby achieving an enhanced Fenton reaction in tumor microenvironment. In addition, the magnetosomes in AMB-1 are used as MRI contrast agent, and the curing process is visualized. This tumor microenvironment-responsive MTB-based multi-drug delivery platform displays a potency to combat tumor and demonstrates the utility and practicality of understanding the cooperative molecular mechanism when designing multi-drug combination therapies.

Providing safely-managed sanitation/hygiene requires key competencies for education, training, service delivery, enterprise development and management, product and infrastructure design and development, construction and installation, governance, financing, research, etc. These strategic sanitation capacities will have to be built from higher education’s academic and professional programmes structured and designed to produce skilled and knowledgeable professionals and practitioners. This study aims to investigate the quality of the sanitation/hygiene management content of Environmental Health programmes; the adequacy of the existing central curricula; and the perception of environmental health sanitation/hygiene-trained professionals to determine the next phase for building knowledge and capacity of sanitation professionals in Nigeria through higher education institutions. A multilevel mixed method concurrent study was used for sampling and data collection with a multilevel perception analysis to examine the perceptions of students, lecturers and graduate alumni as well as employers/supervisors and clients/service-users of sanitation/hygiene related graduates. The main findings of this paper show limited understanding of the concepts of contemporary issues of sanitation/hygiene management; the central/national teaching and curricula were found to be seriously out of date; and clients/service-users were dissatisfied with the skills and knowledge levels of the graduates. The study concludes by recommending a national sanitation management higher education pathway to guide the provision of integrated sanitation/hygiene management education at higher education institutions (HEIs), to build effective, efficient, competent, and sufficient workforce for the country.

The performance of bearings plays a pivotal role in determining the dependability and security of rotating machinery. In intricate systems demanding exceptional reliability and safety, the ability to accurately forecast fault occurrences during operation holds profound significance. Such predictions serve as invaluable guides for crafting well-considered reliability strategies and executing maintenance practices aimed at enhancing reliability. In order to ensure the reliability of bearing operation, this article investigates the application of three advanced techniques—Maximum Correlation Kurtosis Deconvolution (MCKD), Multi-Scale Permutation Entropy (MPE), and Long Short-Term Memory (LSTM) recurrent neural networks—for the prediction of the remaining useful life (RUL) of rolling bearings. Each technique's principles, methodologies, and applications are comprehensively reviewed, offering insights into their respective strengths and limitations. Case studies and experimental evaluations are presented to assess their performance in RUL prediction. Findings reveal that MCKD enhances fault signatures, MPE captures complexity, and LSTM excels in modeling temporal patterns. The root mean square error of the prediction results is 0.007. The fusion of these techniques offers a comprehensive approach to RUL prediction, leveraging their unique attributes for more accurate and reliable predictions.

In this paper, precise examination of multi-port antennas with large mutual coupling between the ports is studied. For this purpose, some vital parameters such as active reflection coefficients and realised gain are emphasized. The main motivation of this research is the ignorance of this issue in several recently published papers. Hence, corrections and criticisms to some recently reported results are presented. At first, a microstrip patch consisting of two inverted U-slots is re-examined, which has been proposed in a recently published paper for wideband applications. However, the authors did not present satisfactory results to indicate the performance of the proposed structure. In reverse, some important parameters such as the antenna gain appear to be incorrectly reported. In this paper, the characteristics of the antenna are compared with a simple 50 Ω microstrip line excited by two probes, indicating no significant differences. In the remainder of this paper, some corrections are provided on two examples of wide-beam circularly polarised multi-fed antennas for satellite applications. The first example is the multi-fed spiral antennas with folded arms, which have been proposed as the widebeam antennas at 435 MHz. It is indicated that the antenna height should be increased for better performance. The second example is the quadrifilar square helical antennas with folded arms, which have been proposed as the widebeam antennas for 435 MHz with minor responses at 145 MHz. Some corrections are presented on the previously reported minor responses at 145 MHz.

In the extra-thick coal seams and multi-layered hard roofs, the longwall hydraulic support yielding, coal face spalling, strong deformations of goaf-side entry, and severe ground pressure dynamic events typically occur at the longwall top coal caving longwall faces. Based on the Key strata theory an overburden caving model is proposed here to predict the multilayered hard strata behaviour. The proposed model together with the measured stress changes in coal seam and underground observations in Tongxin coal mine provides a new idea to analyse stress changes in coal and help to minimise rock bursts in the multi-layered hard rock ground. Using the proposed primary Key and the sub-Key strata units the model predicts the formation and instability of the overlying strata that leads to abrupt dynamic changes to the surrounding rock stress. The data obtained from the vertical stress monitoring in the 38 m wide coal pillar located adjacent to the longwall face indicates that the Key strata layers have a significant influence on ground behaviour. Sudden dynamically driven unloading of strata was caused by the first caving of the sub-Key strata while reloading of the vertical stress occurred when the goaf overhang of the sub-Key strata failed. Based on this findings several measures were recommended to minimise the undesirable dynamic occurrences including pre-split of the hard Key strata by blasting and using the energy consumption yielding reinforcement to support the damage prone gate road areas. Use of the numerical modelling simulations was suggested to improve the key theory accuracy.

With the urgent need of precise positioning faced by internet of things (IoT) applications, the universality and cost of indoor positioning devices become key factors. Since the 5G network has been widely deployed, new opportunity is brought by tightly fusing the traditional low-cost sensors, i.e., the magnetometer. In this study, using 5G channel state information (CSI) and geomagnetic data, a multi-input convolutional neural network (CNN) localization system was proposed. First, to generate a data tensor that is easy for CNN processing, the raw data was reconstructed individually. Then, to comprehensively incorporate the features of 5G CSI and geomagnetic strength data, the ReLU function was chosen as the activation function of the convolutional layer. After that, a multi-input CNN was trained using the incorporated geomagnetic strength and CSI amplitude in the off-line side, and the trained CNN was recorded as a location fingerprint, which can be used for the user position prediction. Finally, in the online side and using a multi-input CNN, the 2-D coordinates are estimated and tested indoors in a typical conference room scenario. The results showed that longer sampling time of fingerprint data result in better uniqueness of the reference point, while the data collection time of locating points does not need to be long. Taking the positioning efficiency and accuracy into consideration, a sampling time of 3s at the reference point and 0.2s at the locating point are recommended. The positioning accuracy using the proposed method was 1.41 m, with an improvement of 22.9% compared with the 5G positioning, and an improvement of 18.0% compared with the 5G and geomagnetic fusing positioning using single CNN.

The robust fusion estimation problem of a multi-sensor system with communication constraints, random packet drops, d-step state delays, and deterministic control inputs is investigated. The state augmentation method is used to transform the time delay system into a non-time delay system, and then a robust fusion estimation algorithm based on sensitivity penalty is proposed and the pseudo-cross-covariance matrix is updated. An event-triggered robust fusion estimator with state delay and deterministic control inputs is considered to make the model closer to reality while effectively reducing network congestion and lowering communication costs. Conditions are given to ensure that the estimation errors of the robust fusion estimator are uniform boundedness. Two sets of numerical simulations are provided to illustrate the effectiveness of the derived fusion estimator.

The changing of land use and land cover (LULC) are both affected by climate and human activity and affect climate, biological diversity, and human well-being. Accurate and timely information about the LULC pattern and change is crucial for land management decision-making, ecosystem monitoring, and urban planning, especially in developing economies undergoing industrialization, urbanization, and globalization. Biodiversity degradation and urban expansion in eastern China are research hot-spots. However, the influence of LULC changes on the region remains largely unexplored. Here, an object-based and multi-temporal image analysis approach was developed to detect how LULC changes during 1985-2015 in the Tiaoxi watershed (Zhejiang province, eastern China) using Landsat TM and OLI data. The main objective of this study is to improve the accuracy of unsupervised change detection from object-based and multi-temporal images. To this end, a total of seven LULC maps are generated with multi-temporal images. A random stratified sample design was used for assessing change detection accuracy. The proposed method achieved an overall accuracy of 91.86%, 92.14%, 92.00%, and 93.86% for 2000, 2005, 2010, and 2015, respectively. Nevertheless, the proposed method, in conjunction with object-oriented and multi-temporal satellite images, offers a robust and flexible approach to LULC changes mapping that helps with emergency response and government management. Urbanization and agriculture efficiency are the main reasons for LULC changes in the region. We anticipate that this freely available data will improve the modeling for surface forcing, provide evidence of changes in LULC, and inform water-management decision-making.

A multi-server parallel system dispatches the incoming job, which contains kn tasks into n servers. A job is considered to be computed if all the tasks associated with the job are processed. One job’s tasks can be encoded into at least kn “replicas” such that the job is considered to be served if any kn replicas finishing computation. In this paper, we analyze the random scheduling policy of a multi-server computing system under discrete time model in terms of Quality of Exponent (QoE), which is defined as the probability exponent that a typical job can be computed within a given number of time slots. We let kn/n be a constant. Assuming that any task of any job can be randomly dispatched by a “scheduler” to any server, and computing each task takes exactly one time slot. We divide the calculation of probability exponent into two parts, exponent of numerator and exponent of denominator. For the denominator, we give the almost exact exponent using Lagrange multiplier method, while for the numerator, an upper bound of the numerator’s exponent is provided. In addition, we also express the exponent in terms of information theoretical quantities and reconsider both of exponents in the context of large deviation theory.

A stable driver state is essential in the process of manually transition control, which inevitably occurs in Level 3 automated driving situations. To this end, this paper proposed a CNN algorithm-based driver state monitoring system that uses multi-sensor data such as driver's face image, biometric information, and vehicle behavior information as input. This system calculates the probability of drowsiness for each of the four time periods using a convolutional neural network (CNN) based on ToF camera-based eye blinking, ECG information (pulse rate) embedded in the steering wheel, and vehicle information (steering angle data). In order to build a reliable and high-quality training dataset (Ground Truth) for the CNN algorithm, a baseline was established by matching the driver's face image with the electrocardiogram (ECG) and electroencephalogram (EEG) changes in the drowsy and normal states. In a simulation test of the proposed CNN algorithm using more than 20,000 driver image data acquired using a driving simulator, the TNR was 94.8% and the accuracy was 94.2%. Our proposed method is expected to minimize human errors that may occur when switching control by monitoring inappropriate driver state (drowsiness) in real time.

Precise monitoring of different environmental parameters and contaminations during food processing and storage is a key factor for maintaining its safety and nutritional value. Thus, developing reliable, efficient, cost-effective sensor devices for these purposes is of utmost importance. In this paper, we show that Poly-(diallyl-dimethylammonium chloride)/reduced Graphene oxide (PDAC/rGO) films produced by a simple Layer-by-Layer deposition can be effectively used to monitor temperature, relative humidity and the presence of volatile organic compounds as indicators for spoilage odors. At the same time, they show potential for electrochemical detection of organophosphate pesticide dimethoate. By monitoring the resistance/impedance changes during temperature and relative humidity variations or upon the exposure of PDAC/rGO films to methanol, good linear responses were obtained in the temperature range of 10-100 °C, 15-95 % relative humidity, and 35 ppm - 55 ppm of methanol. Moreover, linearity in the electrochemical detection of dimethoate is shown for the concentrations in the order of 102 µmol dm−3. The analytical response to different external stimuli and analytes depends on the number of layers deposited, affecting sensors’ sensitivity, response and recovery time, and long-term stability. The presented results could serve as a starting point for developing advanced multimodal sensor devices and sensor arrays with high potential for analytical applications in food safety and quality monitoring.

Non-pneumatic tires have gained a lot of attention due to their advantages, including not having to worry about getting a flat tire. In this type of tire, metamaterial cells replace the pneumatic part of the tire. In general, metamaterials are formed by stacking cells together. These cells are obtained by various methods including topology optimization. Therefore, in this research, to achieve a metamaterial cell suitable for a non-pneumatic tire with the objective function of increasing compressive strength and bending fatigue life, optimization for three types of geometry including (1) square plane, (2) rectangular plane, and (3) entire circumference of tire and three types of material including polylactic acid (PLA), thermoplastic polyurethane (TPU) and void have been done. Optimization has been implemented by using MATLAB code in 2D mode. The cubic cell is obtained from extruding the optimized response of the square plane. From the optimized response of the rectangular plane, the cylindrical cell and from extruding the optimized response of the entire circumference of tire to the tire cross-section size, the main geometry of the tire has been calculated. Finally, to check the quality of 3D printing in producing cells and how they are connected, the optimal cell fabricated by the fused deposition modeling (FDM) method has been observed using a field-emission scanning electron microscopy (FE-SEM). The results show that in the optimization of the square plane, the sample with the minimum remaining weight constraint equal to 40% and in the optimization of the rectangular plane and the entire circumference of tire, the sample with the minimum remaining weight constraint equal to 60% was selected as the optimal sample. From checking the quality of 3D printing, it has been concluded that PLA and TPU materials are completely connected.

In the proposed article, the issues of increasing the synchronizing ability of the system of coordinated rotation of asynchronous motors are considered. Based on the T-shaped equivalent circuit, electromechanical relationships were obtained with changes in the value of the total rotor resistance and the supply voltage of individual motors. An algorithm for calculating the torques, stator and rotor currents of the motors of the system has been compiled. Based on the calculations obtained, the mechanical characteristics of the system asynchronous motors are constructed for various values of total resistance, supply voltages and rotor positions. The obtained data and graphs confirm the adequacy of the theory obtained in an analytical way. Functional and structural diagrams in small scales have been compiled, which allow simulating transient operation modes of multi-motor asynchronous electric drives in the Matlab application package. Multi-motor asynchronous electric drives with adjustable supply voltages, as well as with preliminary synchronization and synchronous braking, have been developed. Compilation of a program for the stability of a nonlinear system of a multi-motor asynchronous electric drive (MAEDs) with a thyristor voltage converter (TVC) in Matlab. Also, the modes of soft start, load shedding and surge on the motor shaft are simulated, confirming the stability of the system.

The intelligent elderly care model places new demands on the skills of aging caregivers. The identification and development of forward-thinking, high-potential nursing talent is essential for advancing the intelligent elderly care sector. Multi-benchmarking selection and competitive analysis is used to evaluate and identify nursing personnel in the rehabilitation treatment center of a hospital in Hefei City. Using proxy evaluation and democratic evaluation model, three types of benchmarks such as single item benchmark, individual benchmark and group benchmark were identified and selected, and the professional nursing team was constructed based on the evaluation results. Different from the traditional other-directed evaluation, multi-benchmarking selection and competitive analysis is self-directed evaluation, this method is more conducive to the identification of high-potential and digital nursing talents by intelligent elderly service organizations, and facilitates the formation of professional nursing teams with complementary strengths and cross-fertilization, so as to satisfy the diversified and multi-level needs of the elderly for intelligent elderly services.

Anti-microbial drugs and coccidiostat compounds are commonly used in poultry farming. These compounds are subsequently excreted and released into the environment via broiler litter (BL) and can re-enter the food chain as fertilizer and/or animal feed. Residues of such drugs can encourage the appearance of antibiotic-resistant bacteria (ARB), as well as toxicity, when found in animal feed. The aim of this study was to develop a multi-residue analytic method for assessing 30 an-ti-microbial drugs and coccidiostats associated with BL and investigate the effects of stacking treatment on anti-microbial and coccidiostat residue degradation in BL used for ruminant feed at the lab-scale. Today, most analytical methods used to identify and quantitate these drug residues are traditional, and may be specific to some antimicrobials. All call for lengthy sample preparation and may present limitations in assessing broiler litter. Such conventional mul-ti-anti-microbial/coccidiostat residue detection assays employ liquid-liquid extraction (LLE) and solid phase extraction (SPE) for sample purification. In our research, LLE and SPE were replaced by Quick, Easy, Cheap, Effective, Rugged and Safe (QuEChERS) clean-up steps for 30 an-ti-microbials and coccidiostats used in broiler farming and detection by liquid chromatography mass spectrometry (LC/MS/ MS). Using this method, recoveries were 70-120%, with the exception of norfloxacin and narasin, which showed recoveries of 67 and 68%, respectively. This analytical meth-od results show that eight samples were not detected in 42 samples, while in 34 samples, one or more drugs were present. Eighteen anti-microbial and coccidiostat residues were detected dur-ing one year sample collaction. The most frequently detected residues were narasin, nicarbazin, monensin, robenidine, oxytetracycline, chlortetracycline, norfloxacin and sulfachloropyridazine, seen at levels from 0.4 to 8.9 mg•kg-1 (ppm). Nineteen anti-microbials and one coccidiostat were degraded to 95% by the stacking treatment. However, tilmicosin and eight coccidiostats persisted in litter (26-100%). The use of antimicrobials and coccidiostats in animal farming is of paramount concern with respect to human, animal and environmental contamination issues and as a source of resistant pathogenic bacteria. Still, most farmers use BL as ruminant feed and fertilizer without processing. Even though the effects of the stacking treatments on degradation of antimicrobials were significantly high, the degradation of coccidiostats and tilmicosin was limited. Clearly, BL should be treated and supervised before use as feed supplement or for land application. Hence, the present method, designed to support these goals, was optimized in terms of sensitivity and se-lectivity for the analytes addressed.

The ground consists of many layers of soil with different properties. The propagation speed and path of seismic waves are affected by different soil layers. It is necessary to understand that layered soil exhibits different dynamic behaviors and responses under the action of seismic waves. This study utilized weathered soil and silica sand as materials to create multi-layered soil conditions with varying degrees of compaction. By conducting 1 g shaking table test on multi-layered soil, the interaction and influence between different soil layers under different earthquake conditions were observed. The approach of numerical analysis aims to validate the experimental results and provide an in-depth understanding of the dynamic behaviors of multi-layered soil grounds during seismic events. The results of this study show that the amplification effect of seismic waves is related to the number of soil layers and the degree of compaction of the soil layers. This indicates that the multi-layered soil ground and the behavior of the soil layers play an important role in the propagation and impact of seismic waves, and this amplification effect is of great significance in actual seismic disaster risk assessment and design.

Object recognition is an essential element of machine intelligence tasks. However, one model cannot practically be trained to identify all the possible objects it encounters. An ensemble of models may be needed to cater to a broader range of objects. Building a mathematical understanding of the relationship between various objects that share comparable outlined features is envisaged as an effective method of improving the model ensemble through a pre-processing stage, where these objects' features are grouped under a broader classification umbrella. This paper proposes a mechanism to train an ensemble of recognition models coupled with a model selection scheme to scale-up object recognition in a multi-model system. An algorithmic relationship between the learnt parameters of a trained classification model and the features of input images is presented in the paper for the system to learn the model selection scheme. The multiple models are built with a CNN structure, whereas the image features are extracted using a CNN/VGG16 architecture. Based on the models' excitation weights, a neural network model selection algorithm, which links a new object with the models and decides how close the features of the object are to the trained models for selecting a particular model for object recognition is developed and tested on a five-model neural network platform. The experiment results show the proposed model selection scheme is highly effective and accurate in selecting an appropriate model for a network of multiple models.

There always exist steel cuttings, holes and cracks at the interfaces in the explosive composite plate. Multi-pass friction stir processing (M-FSP) is proposed in this research to optimize the interface microstructure and the interface connection for 1060Al/Q235 explosive composite plate. Results show that the microstructures of 1060Al after M-FSP are fine and uniform owing to the strong stirring effect and recrystallization. Micro-defects formed by the explosive welding can be repaired by the M-FSP. However, M-FSP can also form tunnel defects in the aluminum, especially when the passes are one and two. The melting block and the melting lump in the composite plates are easy to become source of crack. The shear strengths and the bending properties for the 1060Al/Q235 explosive composite plate after M-FSP are the best when the passes are three, with the tool rotation speed of 1200rpm and the forward speed of 60mm/min. The optimized interfaces for the explosive composite plate after M-FSP are mainly by the metallurgical bondings, with a certain thickness and are discontinuous. Therefore, the crack extension stress is the largest and the mechanical properties are the best.

In this paper, a multi-mode waveguide-based optical resonator is proposed for an integrated optical refractive index sensor. Conventional optical resonators have been studied for single-mode waveguide-based resonators to enhance the performance, but mass production is limited owing to the high fabrication costs of nano-scale structures. To overcome this problem, we designed an S-bend resonator based on a micro-scale multi-mode waveguide. In general, multi-mode waveguides cannot be utilized as optical resonators, because of a performance degradation resulting from modal dispersion and an output transmission with multi-peaks. Therefore, we exploited the mode discrimination phenomenon using the bending loss, and the resulting S-bend resonator yielded an output transmission without multi-peaks. This phenomenon is utilized to remove higher-order modes efficiently using the difference in the effective refractive index between the higher-order and fundamental modes. As a result, the resonator achieved a Q-factor and sensitivity of 2.3x10³ and 52 nm/RIU, respectively, using the variational finite-difference time-domain method. These results show that the multi-mode waveguide-based S-bend resonator with a wide line width can be utilized as a refractive index sensor.

This paper presents experimental identification and vibration suppression of a flexible manipulator with non-collocated piezoelectric actuators and strain sensors using optimal multi-poles placement control. To precisely identify the system model, a reduced order transfer function with relocated zeros is proposed, and a first-order inertia element is added to the model to compensate the non-collocation. Comparisons show the identified model match closely with the experimental results both in the time and frequency domains, and a fit of 97.2% is achieved. Based on the identified model, a full-state multi-poles placement controller is designed, and the optimal locations of the closed loop poles are determined. The feasibility of the proposed controller is validated by simulations. Moreover, the controller is tested for different locations of the closed loop poles, and an excellent performance of the optimal locations of the closed loop poles is shown. Finally, the effectiveness of the proposed controller is demonstrated by experiments. Results show that the vibrations of the expected modes are significantly diminished. Besides, vibrations of the higher modes are also slightly suppressed. Accordingly, multi-mode vibrations of the manipulator are well attenuated, and the tip displacement converges quickly with the proposed method.

As the whisky industry applies circular economy principles to maximize resource utilization and minimize environmental impact, companies become exposed to several risks, which require complex assessments to ensure reliable outcomes. This study provides an organized framework to identify, prioritize and rank various risk factors commonly observed in whisky industry through the development of an Analytical Hierarchy Process (AHP) multi-criteria analysis model. Experts from 18 small European distilleries identified five main risk criteria and nineteen sub-criteria from brainstorming workplace observations, and categorized them as: environmental (5), operational (4), technological innovation (3), food safety (3) and economical (4) risks. The Analytical Hierarchy Process (AHP) approach was used to determine the weights and ranks of the main criteria and sub-criteria based on the survey responses received from experts from each distillery. The final judgements are consistent, as indicated by consistency values (CR) of less than 0.1 for all risk criteria. Unlike traditional risk assessment methods, the AHP model effectively integrates qualitative and quantitative data, aiding strategic decision-making in the whisky industry by breaking down complex problems into manageable sub-problems. Future research directions may expand the criteria and explore additional sustainable practices.

Pedestrian object detection plays a significant role in intelligent systems such as intelligent traffic and monitoring. Traditional machine learning methods on pedestrian detection have shown various drawbacks, e.g., low accuracy, slow speed, etc. The Convolutional Neural Network (CNN) based object detection algorithms have demonstrated remarkable advantages in the field of pedestrian detection. However, the mainstream CNNs still face the problems of slow speed and low detection accuracy, especially on small and occluded targets from aerial perspective. In this paper, we propose Multi-Scale Attention YOLO (MSA-YOLO) detection algorithm to address the above issues. MSA-YOLO includes a Squeeze, Excitation and Cross Stage Partial (SECSP) channel attention module for CNNs to extract richer pedestrian features with a small number of extra parameters. It also contains a multi-scale prediction module to capture the information among different pedestrian scales, which can recognize the small objects with higher accuracy and significantly reduce the missed detection. To sufficiently evaluate our proposed model, we manually collect and annotate a new benchmark dataset, Aerial Pedestrian Dataset, which has much more sample annotations, features, scenes and image view angles than the existing benchmark datasets. In addition, the images in our dataset have higher resolution than most of benchmark pedestrian detection datasets, which can provide more detailed features of pedestrians and thus improve the model performance. When tested on Aerial Pedestrian Dataset, our proposed MSA-YOLO algorithm significantly outperforms the most used baseline models with almost the same model size. This shows the efficiency of our proposed model. (The code and new dataset will be released to the public later.)

Sustainability in material purchasing is a growing area of research. Goods purchasing decisions strongly affect transportation path flows, vehicle consolidation, inventory levels and related obsolescence costs. Within a global sourcing context, companies experience the need of new decision making approaches capable to consider a large variety of factors, also linked with society and environment. Environmental impact assessment has become a key requirement for materials purchasing and transportation decisions since global warming is a rising concern both in academic and industrial researches. In fact, it is well known that the freight transport industry is responsible for large amounts of carbon emissions contributing to global warming. In this paper, we initially analyse and compare the environmental economic policies established by the International Governments in relation to the carbon trading systems adopted. Then, we develop a multi-objective lot sizing approach useful in practice to define the sustainable quantity to purchase when a Cap and Trade mitigation policy is present. We further analyse the model behaviour according to different carbon price values by demonstrating that carbon prices are still far too low to motivate managers towards sustainable purchasing choices.

The present study aims to evaluate the capability of the TRMM-3B42-(V7) precipitation product to estimate appropriate precipitation rates in the Upper Indus basin (UIB) and the analysis of the dependency of the estimates’ accuracies on the time scale. To that avail statistical analyses and comparison of the TMPA- products with gauge measurements in the UIB are carried out. The dependency of the TMPA estimates’ quality on the time scale is analysed by comparisons of daily, monthly, seasonal and annual sums for the UIB. The results show considerable biases in the TMPA- (TRMM) precipitation estimates for the UIB, as well as high false alarms and miss ratios. The correlation of the TMPA- estimates with ground-based gauge data increases considerably and almost in a linear fashion with increasing temporal aggregation, i.e. time scale. The BIAS is mostly positive for the summer season, while for the winter season it is predominantly negative, thereby showing a slight over-estimation of the precipitation in summer and under-estimation in winter. The results of the study suggest that, in spite of these discrepancies between TMPA- estimates and gauge data, the use of the former in hydrological watershed modelling, endeavoured presently by the authors, may be a valuable alternative in data- scarce regions, like the UIB, but still must be taken with a grain of salt.

The forest is a complex and dynamic ecosystem that requires integrated planning and management, considering economic, social, environmental, and ecological dimensions. Different stakeholders often have conflicting goals, making optimal management decisions challenging. This study aims to balance increasing economic benefits for forest users with reducing negative environmental impacts, aligning the interests of managers, government institutions, and policymakers. To achieve this, multi-objective optimization methods and game theory were used. The objectives were to maximize the net present value of wood harvesting and the amount of carbon sequestration. The study was conducted in the Shafarood forest in northern Iran. Data collected included stumpage prices, variable harvesting costs, tree density per ha, volume per ha, growth rates, interest rates, carbon sequestration, and labor costs. Using this data, models were developed for the expected mean price of various species, stored carbon, logistics growth, and labor. After adjusting the objective functions and model constraints, the range of Pareto optimal solutions for the multi-objective model and the Nash equilibrium for the game theory model were determined using the epsilon-constrain method. The results indicate that both modeling approaches can identify optimal points for balancing economic and environmental goals. The Pareto optimal range and Nash equilibrium allow for informed decision-making in managing the Hyrcanian forests, accommodating different user goals. Therefore, both models are effective tools for forest management planning and provide a framework for achieving sustainable management practices.

Differential Evolution (DE) is an evolutionary algorithm that has become increasingly popular due to its effectiveness and efficiency. However, its adaptation for multi-objective optimization requires further investigation. To address this issue, a novel algorithm called ILSDEMO has been proposed, which incorporates indicator-based selection and local search into a self-adaptive DE. ILSDEMO employs an archive population to store non-dominated solutions, generating an initial population uniformly distributed over the feasible solution space using orthogonal design. Additionally, two variants of DE are used to expedite convergence, while q-Gaussian mutation is utilized to exploit better trial individuals. The k-nearest neighbor rule is used to eliminate crowded solutions, and indicator-based selection is employed to generate a new parent population without diversity preservation. The performance of ILSDEMO was investigated on the test instances from the ZDT series and DTLZ series in terms of the selected indicators. The results suggest that ILSDEMO accurately and evenly approximates the true Pareto front compared to NSGAII, IBEA, and DEMO.

Geometrical assessments of human skull have been done based on the anatomical landmarks. Automatic detection of the landmarks, if developed, will be a great help not only medically, but also anthropologically. An automated system with multi-phased deep learning networks to predict three-dimensional coordinate values of cranio-facial landmarks, was developed. From a publicly available database, computed tomography images of craniofacial area were obtained. They were digitally reconstructed into three-dimensional models. Sixteen anatomical landmarks were plotted on each of the models and coordinate values of them were recorded. Three-phased regression deep learning networks were trained respectively with 90 training datasets. For evaluation, 30 testing datasets were employed. Three-dimensional error for the first phase, testing 30 data, was 11.60 pixels in average. (1 pixel = 500 / 512 mm) For the second phase, it was significantly improved to 4.66 pixels. For the third phase, it was significantly progressed to 2.88. This was comparable to the gaps between the landmarks, plotted by two experienced practitioners. Our proposing method of multi-phased prediction, coarse detection first and narrowing down the detection area, may be a possible solution, within the physical limitation of memory and computation.

Nitrile butadiene rubber (NBR) and its various composites are extensively studied as matrix materials for oil-free lubricated mechanical friction surfaces. While numerous macroscopic friction experiments can compare the frictional performance of different NBR composites, the complex material preparation and low experimental efficiency pose challenges. Nanoscale molecular dynamics (MD) simulations can help develop materials with improved friction properties, but they cannot directly provide the friction coefficients of actual macroscopic friction surfaces. Therefore, it is important to integrate the advantages of macroscopic and nanoscale friction studies and perform a synergistic analysis to modify the friction properties of composite materials. In this study, a multi-scale approach is proposed to simulate the frictional characteristics of carbon nanotube (CNT)-reinforced NBR by combining the MD friction simulation， micromechanical bridging model, and macroscopic finite element analysis (FEA) methods. The results of the multi-scale friction simulation of copper (Cu)-CNT/NBR composites show that the addition of CNTs significantly improves the frictional properties of NBR, and the extent of the improvement is related to the mass fraction of CNTs. As the mass fraction of CNTs increases (0%, 1.25%, 2.5%, 5%), the coefficient of friction decreases from 0.50 to 0.38. The results are validated by ring-block friction experiments at the same scale as the simulations.

Multi-walled carbon nanotubes (MWCNTs) and graphene oxide (GO) reinforced carbon foam (CF) composite were prepared by direct pyrolysis of MWCNTs, GO and mesophase coal tar pitch. The effect of additive amount of the mixture of MWCNTs and GO on the microstruture and properties of carbon foam was analzyed by transmission electron miscroscopy (TEM), scanning electron microscopy (SEM), X-ray diffraction (XRD), Four-probe resistance meter, universal testing machine, and laser thermal conductivity tester respectively. The result shows that MWCNTs and GO had significant impact on the microstructure of carbon foam. Futhermore, the electrical, mechanical and thermal properties of carbon foam composites were significantly enhanced by increasing the additive amount. Maximum compressive strenght of 19.2 MPa and Young’s modulus of 56.8 MPa of CF composite were observed. Similarly, Highest thermal conductivity of 30.91 W/m.K and electrical conductivity of 27.2 ×103 S/m were observed at 2 wt. % of MWCNTs-GO additive loading.

Vaccines decrease morbidity and mortality. Nevertheless, their benefits depend on public response. During COVID-19, vaccine hesitancy and refusal were rampant, threatening public health. A thorough understand-ing of opponents' arguments is required to address the diffusion of unreliable information on social media and prevent vaccine hesitancy from developing into vaccine refusal. Accordingly, the article examines vac-cine opponents' justifications on social media. Textual content analysis of reader comments on three health-related Israeli Facebook pages was conducted. Data collection encompassed the Israeli COVID-19 vaccination period from October 2020 to May 2022. The comments were analyzed according to the health beliefs model (HBM). We found that vaccine opponents were characterized by low perceptions of the severity of the disease combined with high perceptions of the damages of the vaccine; low perceived benefits of vac-cine compliance; vaccine hesitancy and fear along with public distrust as barriers to change; and call for ac-tion to resist the vaccine and spread related anti-establishment views on the web. As vaccination hesitancy was found to develop into public distrust in the state systems and escalate into conspiracy beliefs and an-ti-vaccination activism, its early detection may prevent future vaccine resistance.

In recent years, how to combine intelligent prospecting algorithms such as random forest with a large number of geological and mineral data for quantitative prediction of exploration geochemistry has become an important topic of concern to quantitatively improve the accuracy of target delineation. The ore-forming geological conditions in the central Kunlun area of Xinjiang are great and have good prospecting prospects. However, due to the exhaustion of shallow deposits and the lag of geological prospecting work in the past ten years, there has been no expected breakthrough in the search for large and super-large metal deposits for many years. There has been a serious shortage of reserve resources. The use of new theories, new methods and new technologies for mineral resources investigation and evaluation has become an urgent need in the current prospecting work. In view of this, based on the existing spatial database of geological and mineral resources in the central Kunlun of Xinjiang, combined with the geological characteristics, genesis and metallogenic regularity of the area, this paper carried out a series of studies on gold polymetallic minerals with the help of geographic information system and data science programming software platform. The researchers integrated geological and regional geochemical data, and constructed a random forest metallogenic discriminant model based on two different sampling methods (integrated random undersampling and selection of training samples) to predict the mineralization of gold polymetallic minerals in the central Kunlun area of Xinjiang and delineate the metallogenic target area. The quantitative prediction of gold polymetallic mineral resources in the central Kunlun area of Xinjiang by two random forest models is compared and discussed: the known ore spots, fault structures and geochemical information are extracted, and the known gold polymetallic ore spots and geochemical data are used to form a training set and a prediction set to construct a machine learning random forest model. The results of prediction evaluation and metallogenic prospect division show that for different sampling methods, the performance evaluation parameters of the training process show that the prediction accuracy of the selected training samples is higher, and the selected training samples are more reliable because they can fully learn the complex information of the original data. In the metallogenic prospect prediction and metallogenic potential division, the random forest model of selecting training samples has more reference value and further exploration research significance in the production problem considering the actual exploration cost because of its small area of high potential prediction area and high proportion of ore bearing per unit area. At the same time, this study innovatively improves the prediction accuracy, reduces the exploration risk, and expands the prospecting idea of machine learning algorithm in mathematical geology in the central Kunlun area of Xinjiang. The delineated metallogenic potential area has positive guiding significance for the actual gold polymetallic prospecting work in this area.

Incident solar radiation (insolation) passing through the forest canopy to the ground surface is either absorbed or scattered. This phenomenon, known as radiation attenuation, is measured using the extinction coefficient (K). The amount of radiation at the ground surface of a given site is effectively controlled by the canopy’s surface and structure, determining its suitability for plant species.Menhinick’s and Simpson biodiversity indexes were selected as spatially explicit response variables for the regression equation using canopy structure metrics as predictors. Independent variables include modeled area solar radiation, LiDAR derived canopy height, effective leaf area index data derived from multi-spectral imagery, and canopy strata metrics derived from LiDAR point-cloud data. The results support the hypothesis that, 1.) canopy surface and strata variability may be associated with understory species diversity due to habitat partitioning and radiation attenuation, and that, 2.) such a model can predict both this relationship and biodiversity clustering.The study data yielded significant correlations between predictor and response variables and was used to produce a multiple-linear model comprising canopy relief, texture of heights, and vegetation density to predict understory plant diversity. When analyzed for spatial autocorrelation, the predicted biodiversity data exhibited non-random spatial continuity.

A humidity-sensitive demand-controlled ventilation system is known for many years. It has been developed and commonly applied in regions with an oceanic climate. Some attempts were made to introduce this solution in Poland in a much severe continental climate. The article evaluates this system's performance and energy consumption applied in an 8-floor multi-unit residential building, virtual reference building described by the National Energy Conservation Agency NAPE, Poland. The simulations using the computer program CONTAM were performed for the whole hating season for Warsaw's climate. Besides passive stack ventilation that worked as a reference, two versions of humidity-sensitive demand-controlled ventilation were checked. The difference between them lies in applying the additional roof fans that convert the system to hybrid. The study confirmed that the application of demand-controlled ventilation in multi-unit residential buildings in a continental climate with warm summer (Dfb) leads to significant energy savings. However, the efforts to ensure acceptable indoor air quality require hybrid ventilation, which reduces the energy benefits. It is especially visible when primary energy use is analyzed.

In developing nations, such as Ekiti State, Nigeria, the use of remote sensing data, especially satellite and UAV imagery, remains significantly underutilized in land administration. This limits the potential of multi-resolution imagery in land governance and socio-economic development. This study examines factors influencing UAV adoption for land administration in Nigeria, mapping six distinct rural, peri-urban, and urban sites, and creating orthomosaics with resolutions ranging from 2.2cm to 3.39cm. Boundaries were manually delineated from multi-resolution orthomosaics to acquire coordinates, and parcel areas were calculated. Using 0.05m UAV imagery as the reference, the Root Mean Square Error (RMSE) was computed to evaluate 0.1, 0.5, and 1m orthomosaics' accuracy for boundary delineation across the six geographical contexts. The Normalized Parcel Area Error (NPAE) was also calculated to determine how the multi-resolution imageries affected the property areas. Results showed a consistent increase in error with increasing resolution (0.1m to 1m) in formal areas (Igedora, Maryland, Okebola) with physical demarcations, from 0.117m to 1.747m RMSE. In contrast, informal settlements exhibited inconsistent error values, indicating a differing impact of resolution on error between formal and informal areas. The research demonstrates the role of physical demarcations in facilitating cadastral mapping, with formal settlements demonstrating the highest suitability. This study recommends the use of imagery resolution specific to each context, offering guidance for improved land governance. Implications and recommendations include promoting awareness of settlement typologies in aerial imagery use for cadastral mapping, leveraging UAVs for high-resolution aerial imagery, and addressing regulatory challenges to promote UAV adoption. Finally, the RMSE and NPAE values can serve as metrics for assessing different resolution images’ fitness for cadastral mapping.

This work analyzes a new indoor laboratory data set looking at early fire indicators in controlled and realistic experiments representing different incipient fire scenarios. The experiments were performed within the confines of an indoor laboratory setting using multiple distributed sensor nodes on different room positions. Each sensor node collected data of particulate matter (PM), volatile organic compounds (VOC), CO, CO2, H2, UV, air temperature and humidity in terms of a multivariate time series. These data hold immense value for researchers within the machine learning and data science communities who are keen on exploring innovative advanced statistical and machine learning techniques. They serve as a valuable resource for the development of early fire detection systems. The analysis of the collected data was carried out in dependence of the manhattan distance between the fire source and the sensor node. We found that especially larger particles (&gt; 0.5 μm) and VOCs show a significant dependency with respect to the intensity as a function of the manhattan distance to the source. Moreover, we observed differences in the propagation behavior of VOCs, PM, and CO, which are particularly relevant in incipient fire scenarios due to the presence of strand popagation effects.

This paper describes a proposed fractional filter-based multi-scale underwater and hazy image enhancement algorithm. The proposed system combines a modified global contrast operator with fractional order-based multi-scale filters used to generate several images, which are fused based on entropy and standard deviation. The multi-scale-global enhancement technique enables fully adaptive and controlled colour correction and contrast enhancement without over exposure of highlights when processing hazy and underwater images. This in addition to illumination/reflectance estimation coupled with global and local contrast enhancement. The proposed algorithm is also compared with the most recent available state-of-the-art multi-scale fusion de-hazing algorithm. Experimental comparisons indicate that the proposed approach yields better edge and contrast enhancement results without halo effect, colour degradation and is faster and more adaptive than all other algorithms from the literature.

Research within the field of hydrology often focuses on comparing stochastic to machine learning (ML) forecasting methods. The comparisons performed are all based on case studies, while an extensive study aiming to provide generalized results on the subject is missing. Herein, we compare 11 stochastic and 9 ML methods regarding their multi-step ahead forecasting properties by conducting 12 large-scale computational experiments based on simulations. Each of these experiments uses 2 000 time series generated by linear stationary stochastic processes. We conduct each simulation experiment twice; the first time using time series of 100 values and the second time using time series of 300 values. Additionally, we conduct a real-world experiment using 405 mean annual river discharge time series of 100 values. We quantify the performance of the methods using 18 metrics. The results indicate that stochastic and ML methods perform equally well.

Internet of things (IoT) is a network of smart things. This indicates the ability of these physical things to transfer information with other physical things. The characteristics of these networks, such as topology dynamicity and energy constraint, challenges the routing problem in these networks. Previous routing methods could not achieve the required performance in this type of network. Therefore, developers of this network designed and developed specific methods in order to satisfy the requirements of these networks. One of the routing methods is utilization of multi-path protocols which send data to its destination using routes with separate links. One of such protocols is AOMDV routing protocol. In this paper, this method is improved using gray system theory which chooses the best paths used for separate routes to send packets. To do this, AOMDV packet format is altered and some fields are added to it so that energy criteria, link expiration time, and signal to noise ratio can also be considered while selecting the best route. The proposed method named RMPGST-IoT is introduced which chooses the routes with highest rank for concurrent transmission of data, using a specific routine based on the gray system theory. In order to evaluate and report the results, the proposed RMPGST-IoT method is compared to the ERGID and ADRM-IoT approaches with regard to throughput, packet receiving rate, packet loss rate, average remaining energy, and network lifetime. The results demonstrate the superior performance of the proposed RMPGST-IoT compared to the ERGID and ADRM-IoT approaches.

Generative models have recently gained popularity in Remote Sensing, offering substantial benefits for interpreting and utilizing satellite imagery across diverse applications such as climate monitoring, urban planning, and wildfire detection. These models are particularly adept at addressing the challenges posed by satellite images, which often exhibit domain variability due to seasonal changes, sensor characteristics, and especially variations in spectral bands. Such variability can significantly impact model performance across various tasks. In response to these challenges, our work introduces a novel approach that harnesses the capabilities of Generative Adversarial Networks (GANs), augmented with Contrastive Learning, to generate target domain images that account for multi-spectral band variations effectively. By maximizing mutual information between corresponding patches and leveraging the power of GANs, our model aims to generate realistic-looking images across different multi-spectral domains. We present a comparative analysis of our model against other well-established generative models, demonstrating its efficacy in generating high-quality satellite images while effectively managing domain variations inherent to multi-spectral diversity.

In this study, the partial least squares regression (PLSR) models were developed using no pre-processing, traditional preprocessing, multi-preprocessing 5 range, multi-preprocessing 3 range, genetic algorithm (GA), and successive projection algorithm (SPA) to assess the higher heating value (HHV) and ultimate analysis of grounded biomass for energy usage employing near-infrared (NIR) spectroscopy. A novel approach was utilized based on the assumption that using multiple pretreatment methods across different sections in the entire NIR wavenumber range would enhance the performance of the model. The performance of the model obtained from 200 biomass samples for HHV and 120 samples for ultimate analysis was compared, and the best model was selected based on the coefficient of determination of validation set, root mean square error of prediction, and the ratio of prediction to deviation values. Based on model performance results, the proposed HHV model from GA-PLSR, and the N and O models from the mul-ti-preprocessing PLSR 5 range method could be used for most applications, including research, whereas the C and H models from GA-PLSR performance is fair and applicable only for rough screening. The overall findings highlight that the multi-preprocessing 5-range method, which was attempted as a novel approach in this study to develop the PLSR model, demonstrated better accuracy for HHV, C, N, and O, improving by 4.1839%, 8.1842%, 3.7587%, and 35.9404%, respec-tively. Therefore, it can be considered a reliable and non-destructive alternative method for rap-idly assessing biomass properties for energy usage and can also be used effectively in biomass trading. However, due to the smaller number of samples used in the model development, more samples are needed to update the model for a robust application.

In this computational study, we investigate the electronic properties of zigzag graphene nano-parallelograms (GNPs), which are parallelogram-shaped graphene nanoribbons of various widths and lengths, using thermally-assisted-occupation density functional theory (TAO-DFT). Our calculations reveal a monotonic decrease in the singlet-triplet energy gap as the GNP length increases. The GNPs possess singlet ground states for all the cases examined. With the increase of GNP length, the vertical ionization potential and fundamental gap decrease monotonically, while the vertical electron affinity increases monotonically. Besides, as the GNP length increases, the symmetrized von Neumann entropy increases monotonically, denoting an increase in the degree of multi-reference character associated with ground-state GNPs. The occupation numbers and real-space representation of active orbitals indicate that there is a transition from the nonradical nature of the shorter GNPs to the increasing polyradical nature of the longer GNPs. In addition, the edge/corner localization of active orbitals is found for the wider and longer GNPs.

Deep learning classification is the state-of-the-art of machine learning approach. Earlier work proves that the deep convolutional neural network has successfully and brilliantly in different applications such as images or video data. Recognizing and clarifying the remote sensing aspect of the earth's surface and exploit land cover and land use (LCLU). First, this article summarized the remote sensing emerging application and challenges for deep learning methods. Second, we propose four approaches to learn efficient and effective CNNs to transfer image representation on the ImageNet dataset to recognize LCLU datasets. We use VGG16, Inception-ResNet-V2, Inception-V3, and DenseNet201 models to extract features from the EACC dataset. We use pre-trained CNNs on ImageNet to extract features. For feature selection we proposed principal component analysis (PCA) to improve accuracy and speed up the model. We train our model by multi-layer perceptron (MLP) as a classifier. Lastly, we apply the multi-granularity encoding ensemble model. We achieve an overall accuracy of 92.3% for the nine-class classification problem. This work will help remote sensing scientists understand deep learning tools and apply them in large-scale remote sensing challenges

This is the second of a two-paper series describing a multi-scale modeling approach developed to simulate crack sensing in polymer fibrous composites by exploiting interruption of electrically conductive carbon nanotube (CNT) networks. The approach is based on the finite element (FE) method. FE models at three different scales, namely the micro-scale, the meso-scale and the macro-scale, have been developed using the ANSYS PDL environment. In the present paper, the meso- and macro-scale analyses are described. In the meso-scale, a two-dimensional model of the CNT/polymer matrix reinforced by carbon fibers is used to develop a crack sensing methodology from a parametric study which relates the crack position and length with the reduction of current flow. In the meso-model, the effective electrical conductivity of the CNT/polymer computed from the micro-scale is used as input. In the macro-scale, the final implementation of the crack sensing methodology is performed on a CNT/polymer/carbon fiber composite volume using as input the electrical response of the cracked CNT/polymer derived at the micro-scale and the crack sensing methodology. Analyses have been performed for cracks of two different lengths. In both cases, the numerical model predicts with good accuracy both the length and position of the crack. These results highlight the prospect of conductive CNT networks to be used as a localized structural health monitoring technique.