Severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2), known to cause 2019-coronavirus disease (COVID-19) pandemic is a zoonotic coronavirus and crosses species to infect human populations, where an efficient transmission of virus occurs human-to-human. Nationwide lockdown is being adopted to stop public transport, keep people at their homes and out of their work, and maintain social distancing. In turn, large geographic areas in the world (including China, Italy, Spain, and USA) has been almost halted. This temporary halt is significantly slashing down the air pollution (air pollutants and warming gases) in most cities across the world. This paper: (i) introduces both COVID-19 and air pollution; (ii) overviews the relation of air pollution with respiratory/lung diseases; (iii) compiles and highlights major data appeared in media and journals reporting lowering of air pollution in major cities those have been highly impacted by the COVID-19; and also (iv) lists the way forward in the present context. Because COVID-19 is an ongoing pandemic and currently far from over, strong conclusions could not be drawn with very limited data at present. The temporary slashed down global air pollution as a result of COVID-19 restrictions are expected to stimulate the researchers, policy makers and governments for the judicious use of resources; thereby minimise the global emissions, and maintain their economies once the pandemic eases. On the other, lifting of the nationwide lockdown and eventual normalisation of the temporarily halted sectors may also reverse the currently COVID-19 pandemic-led significantly slashed down global air pollution that could make the future respiratory health crisis grimmer.

The Oil reservoirs with low permeability account for a large proportion in the world, they surpass half of the total number of the oil reservoirs in China, it is important to exploit this kind of reservoir effectively. The exploitive results of these reservoir using normal water flooding methods are very poor because of the thine pores, bad connections and so on. However, these problems can be well solved by applying gas injection techniques. In this paper, the effects on the recovery effects exerted by the injection parameters such as the oxygen content in the injected air, the injection speed etc. were studied by several experiments using independently designed equipments aiming at one low permeable sandstone reservoir in China. Several conclusions were made from the experiment results: the best recovery effects can be achieved by injecting the oxygen reduced air with 8% of oxygen at the speed of 0.3ml/min (7.41×10-4PV/min) using the methods of injecting the air slugs and the foaming agent slugs alternately; the best oxidation time of the oil was 168 hours and the final oil recovery could be enhanced by 26.5% in this method. It was also showed by the experiments that the larger the permeability ratio is, the larger the recovery factor will be increased. At last, several equations about relationships between the EOR and the air injection parameters were revealed according to the results of the experiments which may offer some references to the LTO process mechanisms study in the similar oil reservoir.

Nowadays industrial dryers are used instead of traditional methods for drying. In designing dryers suitable for controlling the process of drying and reaching a high quality product, it is necessary to predict the instantaneous moisture loss during drying. For this purpose, ten mathematical-experimental models with a neural network model based on the kinetic data of pistachio drying are studied. The data obtained from the cabinet dryer will be evaluated at four temperatures of inlet air and different air velocities. The pistachio seeds will be placed in a thin layer on an aluminum sheet on a drying tray and weighed by a scale attached to the computer at different times. In the neural network, data are divided into three parts: educational (60%), validation (20%) and test (20%). Finally, the best mathematical-experimental model using genetic algorithm and the best neural network structure for predicting instantaneous moisture are selected based on the least squared error and the highest correlation coefficient.

Abstract: The air pollution dispersion modelling via spatial analyses (Land Use Regression – LUR) is an alternative approach to the air quality assessment to the standard air pollution dispersion modelling techniques. Its advantages are mainly much simpler mathematical apparatus, quicker and simpler calculations and a possibility to incorporate other factors affecting pollutant’s concentration. The goal of the study was to model the PM10 particles dispersion modelling via spatial analyses v in Czech-Polish border area of Upper Silesian industrial agglomeration and compare results with results of the standard Gaussian dispersion model SYMOS’97. Results show that standard Gaussian model with the same data as the LUR model gives better results (determination coefficient 71% for Gaussian model to 48% for LUR model). When factors of the land cover and were included into the LUR model, the LUR model results were significantly improved (65% determination coefficient) to the level comparable with Gaussian model. The hybrid approach combining the Gaussian model with the LUR gives superior quality of results (65% determination coefficient).

While previous research has shown the use of attachable air-caps on windows to efficiently reduce a building’s energy consumption, the air-caps considered had to be attached to the entire window’s surface, thus limiting the occupants’ view and creating the inconvenience of needing to detach and attach the air-caps. In this study, a window-mounted air-cap roller module using Velcro tape that may be easily attached, detached, and rolled up or down was developed and performance tested in a full-scale test bed. It was found that as the area of the air-caps attached on a window increased, the required indoor lighting energy increased. However, the window insulation improved, thus reducing the cooling and heating energy needed. Attaching the air-caps to the entire window surface effectively reduced the building’s energy consumption, but views through the window may be disturbed. Thus, the developed window-mounted air-caps enable an occupant to reduce the building energy consumption and maintain their view according to their need. The findings of this study may contribute to a reduction in building energy consumption without sacrificing a pleasant indoor environment. Further studies may be needed to verify their efficacy under varying indoor and outdoor conditions.

Environmental legislation is moving towards global standards for ease of application and to impose sanctions and penalties when necessary, without compromising human health and biota. International environmental measures for control and monitoring of atmospheric air only monitor emissions of SO_x, NO_x, O₃, and Pb. In general, most research work in air pollution done using the analysis of elements in rainwater show analysis of trace metals such as Na, Mg, Zn, and Mn. In this work, trace metals in the rainwater at the city of Goiânia, capital of the State of Goiás, were analyzed. Goiânia is a large city set in a predominantly agricultural province located in central Brazil. Presence of trace metals in rainwater was detected, indicating atmospheric air pollution levels higher than occupational limits set by WHO.

Mineral dust is one of the most important aerosol in mass over the world, affecting health and dynamics. This aerosol is mainly emitted over arid areas but may be long-range transported, impacting the local budget of air quality in many cities. While models were extensively used to study a single specific event, or making a global analysis at coarse resolution, the goal of our study is to simultaneously focus on several areas - Europe, North America, Central Asia, East China and the Caribbean area - for a one month period, March 2014, avoiding any parameter fitting to better simulate a given dust outbreak. The simulation is performed for the first time with the hemispheric version of the CHIMERE model, with a horizontal resolution of 10km. In this study, an overview of several simultaneous dust outbreaks over the north hemisphere is proposed to assess the capability of such modelling tools to predict dust pollution events. A quantitative and qualitative evaluation of the most striking episodes is presented with comparisons to satellite data, ground based Particulate Matter and calcium measurements. Despite some overestimation of dust concentrations far from emission areas, the model is able to simulate the timing of the arrival of dust outbreaks on observational sites. For instance, several spectacular dust storms in the US and China are perfectly captured by the models. The high resolution allows to better describe and understand the orographic effects and the long-range transport of dust plumes.

Traffic congestion is one of the foremost problems confronted by the urban and suburban tenants of today. Traffic congestion increases vehicle emissions and degrades air quality. Urban planners and policy makers have consequently been always investigating choices to alleviate traffic congestion and to enhance air quality. Teleworking is one option that has received significant consideration and has been studied in the recent past. The aim of the study is to explore the relationship between teleworking, air quality and traffic in Switzerland. The analysis relies on panel individual and household level data over the period 2002-2013. We examine five main air pollutants; the sulphur dioxide (SO₂), the ground-level ozone (O₃) the nitrogen dioxide (NO₂), the carbon monoxide (CO) and the particulate matter less than 10 microns (PM₁₀). Based on the fixed effects estimates, teleworking reduces traffic volume by 1.9 per cent. Furthermore, the reduction observed on air pollution is higher for NO₂, CO and PM₁₀ ranging between 3.3-3.7 per cent, followed by O₃ at 2.3 per cent and SO₂ at 2.1 per cent. According to instrumental variable (IV) approach and the two stage least squares (2SLS) method, the effect is higher ranging between 2.6-4.1 per cent. The respective reduction on traffic becomes 2.7 per cent. Overall, the main concluding remark of the study is that teleworking can be a promising tool for urban planning and development, focusing at the traffic volume reduction, and the air quality improvement. Additional policy implications of teleworking and its beneficial effects for the society are further discussed.

A case-crossover study examined how PM_2.5 from Asian Dust Storms (ADS) affects the number of emergency room (ER) admissions for cardiovascular diseases (CVDs) and respiratory diseases (RDs). Our data indicated that PM_2.5 concentration from ADS was highly correlated with ER visits for CVDs and RDs. The odds ratios (OR) increased by 2.92 (95% CI: 1.22-5.08) and 1.86 (95% CI: 1.30-2.91) per increase 10 µg/m³ in PM_2.5 levels, for CVDs and RDs, respectively. A 10 µg/m³ increase in PM_2.5 from ADSs was significantly associated with increase in ER visits for CVDs among those 65 years of age and older (an increase of 2.77 in OR) and for females (an increase of 3.09 in OR). In contrast, PM_2.5 levels had a significant impact on RD ER visits among those under 65 years of age (OR=1.77). The risk of ER visits for CVDs increased on the day when the ADS occurred in Taiwan and the day after (lag 0 and lag 1); the corresponding risk increase for RDs only increased on the fifth day after the ADS (lag 5). In Taiwan’s late winter and spring, the severity of ER visits for CVDs and RDs increases. Environmental protection agencies should employ an early warning system for ADS to reduce high-risk groups’ exposure to PM_2.5.

Daily maximum surface air temperature (Tamax) is a crucial factor for understanding complex land surface processes under rapid climate change. Remote detection of Tamax has widely relied on the empirical relationship between air temperature and land surface temperature (LST), a product derived from remote sensing. However, little is known about how such a relationship is affected by the high heterogeneity in landscapes and dynamics in seasonality. This study aims to advance our understanding of the roles of land cover and seasonal variation in the estimation of Tamax using the MODIS (Moderate Resolution Imaging Spectroradiometer) LST product. We developed statistical models to link Tamax and LST in the middle and lower reaches of the Yangtze River in China for five major land-cover types (i.e., forest, shrub, water, impervious surface, cropland, and grassland) and two seasons (i.e., growing season and non-growing season). Results show that the performance of modeling the Tamax-LST relationship was highly dependent on land cover and seasonal variation. Estimating Tamax over grasslands and water bodies achieved superior performance; while uncertainties were high over forested lands that contained extensive heterogeneity in species types, plant structure, and topography. We further found that all the land-cover specific models developed for the plant non-growing season outperformed the corresponding models developed for the growing season. Discrepancies in model performance mainly occurred in the vegetated areas (forest, cropland, and shrub), suggesting an important role of plant phenology in defining the statistical relationship between Tamax and LST. For impervious surfaces, the challenge of capturing the high spatial heterogeneity in urban settings using the low-resolution MODIS data made Tamax estimation a difficult task, which was especially true in the growing season.

A new three-dimensional numerical model of a polymer electrolyte fuel cell (PEFC) with a single straight channel has been developed to primarily investigate the important impact of the double-sided microporous layer (MPL) coating on the overall performance of the fuel cell and the distribution of the current and the oxygen concentration within the cathode gas diffusion layers (GDLs). Realistic experimentally estimated interfacial contact resistance values between the gas diffusion layer and each of the bipolar plates and the catalyst layer values were incorporated into the model, and parametric studies were performed. The results showed that the double-sided MPL coating could significantly improve the fuel cell performance by up to 30%. Also, it was shown that the neglect of the contact resistance between the MPL and the catalyst layer could overestimate the fuel cell performance by up to 6%. In addition, the results showed that the fuel cell performance and the distribution of the current and oxygen are more sensitive to the porosity of the MPL facing the bipolar plate than the porosity of the MPL facing the catalyst layer. All the above results are presented and critically discussed in detail.

Renewable active sludge is a smart material for wastewater treatment and the protection of surface water bodies. The generated pellets (dried and pelletised dehydrated anaerobically stabilised excess sludge) are produced in a quantity of 31.4 g ± 5.6 g dry matter (DM) per one Population equivalent (PE) calculated to COD (PE_COD) in one day. As pellets are combustible material, their energy utilisation must reach sustainable development goals (SDGs) - a bridge must be created between »treated sewage sludge as the tool to remove pollutants and nutrients from wastewater« and »preparation of the valuable material as a solid recovered fuel (SRF) that meets customer-specific requirements«. Technical Report CEN/TR 15508 and Technical Standard EN ISO 21640 set up methods for specifying and classifying pellets as an SRF. In the last eleven years (2010 – 2021), pellets' net calorific value (NCV) is 13.0 ± 0.7 MJ kg^-1 as received (ar). In 2021, the 80^th percentile of the Hg/NCV ratio was 0.079 mg Hg MJ^-1. In 2010 – 2021, the annual amount of Hg transferred to stakeholders reduced by 64.3 % m/m - from 10.1 kg to 3.67 kg. The halogen contents of the pellets do not threaten corrosion to the incineration facility. Stable pellets' energy potential and perspective ash composition for critical raw materials recovery qualify pellets as a specific waste stream and a renewable material for SRF production.

To obtain an accurate and reproducible experimental results in microbial fuel cell (MFC), it is important to know ‘anode maturation biofilm’ to produce a stable and maximum performance. For this purpose, four single chamber MFCs were tested in this study. The linear sweep voltammetry (LSV) polarization tests illustrated that maximum power densities of three MFCs became stable after 9 weeks. Although there were variations afterwards, such variations were negligible. Average maximum power densities from the 9th to the 17th week were 2,990 mW/m2 (MFC-4), 2,983 mW/m2 (MFC-2), 2,368 mW/m2 (MFC-3) and 837 mW/m2 (MFC-1). Polarization resistance shows that MFC-1 had much larger anode resistance (36.6-85.4 Ω) than the other MFCs (1.7-11.6 Ω). Anodic cyclic voltammetry (CV) shows that current production increased over time and MFC-1 had much smaller current production (24.4 mA) than the other MFCs (31.0-34.9 mA) at 17th week. The increased current production indicates anode biofilm became more mature over time, but overall cell performance did not increased accordingly. Possibly due to the bad inoculation, MFC-1 showed the lowest performance. However, its performance was restored to the initial performance and anode resistance was reduced by 47% at 17th week. This study shows that the optimum anode maturation time is 9 weeks and that bioanode performance is a key factor for MFC performance. This study also shows than LSV polarization and CV tests are accurate and non-destructive measurement methods for diagnosing anode performance.

The hybrid system is analyzed and optimized to produce electric energy in Non-Interconnected Zones in the Colombian Caribbean region, contributing both to the improvement in the reduction of greenhouse gas emissions and to the rational use of energy. A comparative analysis of the performance of these systems was carried using a dynamic model in real wind and solar data. The model is integrated by a Southwest Wind Power Inc. wind turbine. AIR 403, a proton exchange fuel cell (PEM), an electrolyze, a solar panel and a charge regulator based on PID controllers to manipulate oxygen and hydrogen flows in the cell. The transient responses of the cell voltage, current, and power were obtained for the demand of 200 W for changes in solar radiation and wind speed for all days of the year 2013 in the Ernesto Cortissoz airport, Puerto Bolívar, Alfonso Lopez airport and Simon Bolívar airport, by regulating the flow of hydrogen and oxygen into the fuel cell. The maximum contribution of power generation from the fuel cell was presented for the Simon Bolívar airport in November with a value of 158,358W (9.45%). A multi-objective design optimization under a Pareto front is presented for each place studied to minimize the Levelized Cost of Energy and CO₂ emission, where the objective variables are the number of panel and stack in the PV system and PEM.

The processing of woody biomass waste piles for use as fuel instead of burning them was investigated. At each landing slash pile location, a 132 kW grapple excavator was used to transfer the waste piles into a 522 kW horizontal grinder. Economies of scale could be expected when grinding a larger pile, although the efficiency of the loading operation might be diminished. Here, three piles were ground and the operations were time-studied: Small (20 m long × 15 m wide × 4 m high), Medium (30 × 24 × 4 m), and Large (35 × 30 × 4 m) piles. Grinding the Medium pile was found to be the most productive at 30.65 bone dry tons per productive machine hour without delay (BDT/PMH₀), thereby suggesting that there might be an optimum size of slash pile for a grinding operation. We also examined modeling of the excavator and grinder operations, and we observed that the constructed simulation model well-replicated the actual operations. Based on the modeling, we estimated that the productivity of grinding at a landing area of 710 m² of slash pile location was 31.24 BDT/PMH₀, which was the most productive rate.

The object of this work is to determine the correlation on the Nusselt number on the individual rows of a four-row tubular finned heat exchanger with continuous fins with a staggered tube arrangement using CFD modelling. Correlations for calculating Darcy-Weisbach friction factors on individual tube rows were also determined. Relationships for the Nusselt number and friction factor derived for the entire exchanger based on CFD modelling were compared with those available in the literature determined using experimental data. The maximum relative differences between the Nusselt number for a four-row exchanger determined experimentally and by CFD modelling are in the range from 22% for a Reynolds number based on a tube's outside diameter of 1,000 to 30% for a Reynolds number of 13,000. The maximum relative differences between the friction factor for a four-row exchanger determined experimentally and by CFD modelling are in the range of 50% for a Reynolds number based on a tube outer diameter of 1,000 to 10% for a Reynolds number of 13,000. The CFD modeling performed shows that in the range of Reynolds numbers based on hydraulic diameters from 150 to 1,400, the Nusselt number for the first row in a four-row finned heat exchanger is about 22% to 15% higher than the average Nusselt number for the entire exchanger. In the range of Reynolds number changes based on hydraulic diameter from 2,800 to 6,000, the Nusselt numbers on the first and second rows of tubes are close to each other. Correlations on Nusselt numbers and friction factors derived for individual tube rows can be used in the design of plate-fin and tube heat exchangers used in equipment such as air-source heat pumps, automotive radiators, air-conditioning systems and in air hot-liquid coolers. In particular, the correlations can be used to select the optimum number of tube rows in the exchanger.

This paper seeks to enhance volt-var control strategies within reconfigurable microgrids by integrating innovative technologies of power-to-hydrogen (P2H) via electrolyzers and hydrogen-to-power (H2P) through fuel cells. Specifically, it focuses on the simultaneous coordination of electrolyzer, hydrogen storage, and fuel cell alongside on-load tap changers, smart PV inverters, renewable energy sources, diesel generators, and electric vehicle aggregation (EVA) within the microgrid system. Additionally, dynamic network reconfiguration is employed to enhance microgrid flexibility, facilitate power sharing, and improve the overall system adaptability. Given the inherent unpredictability linked to resources, the unscented transformation method is employed to account for these uncertainties in the proposed volt-var control strategy. Finally, the model is formulated as a convex optimization problem and is solved by GUROBI, which leads to having a time-efficient volt-var model with high accuracy. To assess the effectiveness of the model, it is eventually examined on a modified 33-bus microgrid in several cases. Through the results of the under-study microgrid, the developed volt-var control is a great remedy to the simultaneous operation of EVA, P2H and H2P in reconfigurable microgrids with flatter voltage profile across the microgrid.

Hydrogen mobility embodies a promising solution to address the challenges posed by traditional fossil-fuel-based vehicles. The use of hydrogen in small heavy duty road vehicles based on internal combustion engines (ICEs) may be appealing for two fundamental reasons: direct electrification seems less promising in heavy duty transport systems and fuel cell-based hydrogen vehicles implementation may not proceed at the expected pace due to higher investment costs compared to ICEs. On the other hand, hydrogen combustion is gaining attractiveness and relies on robust and cheap technologies, but it is not the only renewable solution. In this framework, this work presents a methodology to assess Weel-to-Whell primary energy consumption and CO2 emissions of small heavy-duty vehicles. The methodology is applied in a real case-study, namely a passenger coach travelling on a 100 km-mission in non-optimized conditions. Therefore, the suitability of hydrogen is compared with standard diesel and other alternative diesel-type fuels (biodiesel and synthetic diesel types). Hydrogen shows competitivity with standard diesel from the point of view of CO2 emission reduction (-29%) while it hides a higher primary energy consumption (+40%). Nonetheless, HVO brings the highest benefits both from the point of view of primary energy consumption and emission reduction, namely -35% and 464-634 kgCO2/100km avoided compared to hydrogen.

This paper focuses on the highly radioactive, long-lasting nuclear waste produced by the currently operating fission reactors and on the way to deal with the sensitive issue of spent fuel reprocessing. The review includes a short description of the fission process and a detailed analysis of the more hazardous radioisotopes produced either by secondary reactions occurring in the nuclear installations or by decay of the fission fragments. Also outlined are the strategies presently adopted to minimize the harmfulness of the nuclear waste to be disposed and discussed advanced options and possible solutions proposed for the recycling of the used fuel and for the reusing of some technologicaly relevant radioisotopes.

Exergy analysis evaluates the efficiency of system components by quantifying the rate of entropy generation. In general, the exergy destruction rate or irreversibility rate was directly obtained through the exergy-balance equation. However, this method cannot determine the origin of the component's entropy generation rate, which is a very important factor in system design and improvement. In this study, a thorough energy, exergy thermoeconomic analysis of a proton exchange membrane fuel cell (PEMFC) was performed, providing the heat transfer rate, entropy generation rate and cost loss rate of each component. The irreversibility rate of each component is obtained by the Gouy-Stodolar theorem. Detailed and extensive exergy and thermoeconomic analyses of PEMFC system have determined that water cooling units experience the greatest heat transfer among the components in the studied PEMFC system, resulting in the greatest irreversibility and thus the greatest monetary flow loss.

Recent advancements have revolutionized interplanetary spacecraft missions by combining low-thrust propulsion systems with planetary Gravity-Assist (GA) maneuvers. This study investigates/improved a novel dual-step efficient-robust homotopy algorithm, grounded in indirect optimal control principles, to analyze fuel-optimal bang-bang control problems. The methodology integrates efficient techniques, including the homotopic method, compatible normalization, and improved switching function detection, aimed at enhancing optimal convergence in solving low-thrust gravity-assist spacecraft missions. To illustrate practical application, an Earth-to-Jupiter interplanetary scenario utilizing Mars-GA is examined. Results demonstrate the algorithm's superior efficacy in achieving fuel efficiency, robust convergence, and remarkable accuracy compared to existing solutions.

Nowadays, the increasingly serious environmental pollution and energy problems urgently require internal combustion engine-based transportation vehicles to upgrade or replace, so the new energy transportation vehicles based on hybrid power and fuel cells have gradually stepped on the stage and continue to innovate. The shipping industry is one of the main sources of global greenhouse gas emissions. The development of clean energy ships represented by fuel cells has attracted wide attention. Fuel cell has the advantages of clean, pollution-free and low noise, but it has some disadvantages such as insufficient dynamic response performance and fast performance decay. Limited by the characteristics of a single energy source, a variety of energy sources and bidirectional DC converters are usually mixed together to form a hybrid ship to improve the flexibility, stability and economy of the ship, and enhance its adaptability to complex sea conditions through the reconfiguration of power system energy. Taking fuel cell ferry "FCS Alsterwasser" as the research object, this study proposed an improved equivalent minimum hydrogen consumption energy management strategy based on fuzzy logic control. First, the power system of the modified mother ship was simulated, and a hybrid power system including fuel cell, lithium iron phosphate battery and supercapacitor was proposed. Then, the dynamic system simulation model and double closed loop PI control model are established in MATLAB/Simulink, and the reliability of the model is verified by the simulation analysis of charge and discharge characteristics. Then, the feasibility of the proposed method is demonstrated by designing simulation experiments based on typical working conditions of the mother ship. The simulation results show that under the premise of meeting the load requirements, the control strategy designed in this paper has a better optimization effect than the S-type penalty function in terms of lithium battery power, lithium battery SOC, bus voltage stability and equivalent hydrogen consumption, which improves the stability and economy of the power system, and has certain engineering practical value.

This paper examines the importance of choice of cooking fuels in wellbeing, analysing relationships between the proportion of population with primary reliance on different types of fuels for cooking (predictor variable), and key wellbeing indices (outcome variables) - Personal Health, Social Life, Civic Engagement, Life Evaluation, Negative Experience. By combining two global datasets from Gallup and WHO, the study adds to current evidence by taking a global perspective. Controlling for demographic factors such as income per capita, age, education level, employment, etc., regression modelling of these relationships show that clean cooking fuels are influential in all of the key wellbeing indices with the exception of the Life Evaluation Index. Among the key wellbeing indices, Personal Health and Negative Experience Indices are the most strongly influenced by choice of clean cooking fuels. By adding access to electricity as an additional predictor variable, the analysis highlights the potential for integrating eCooking into national electrification plans as part of sustainable energy transitions, given that health outcomes (Personal health and Negative experience indices) appear to be as closely linked to choice of cooking fuels as to access to electricity.

In this study the formation of thin-film barrier coatings based on a highly-conducting Bi1.60Er0.4O3 (EDB) solid electrolyte on supporting Ce0.8Sm0.2O1.9 (SDC) electrolyte substrates is implemented for the first time using electrophoretic deposition (EPD). Electrokinetic properties of EDB-based suspensions in a non-aqueous dispersion medium of isopropanol modified with small additions of polyethyleneimine (PEI, 0.26 g/L) and acetylacetone (0.15 g/L), as well as in a mixed isopropanol/acetylacetone (70/30 vol.%) medium are studied. The dependences of the thickness of EDB coatings on voltage and deposition time are obtained using deposition on a model Ni-foil electrode. Preliminary synthesis of a conductive polypyrrole (PPy) polymer film is used to create surface conductivity of non-conductive SDC substrates. The efficiency of using a modified dispersion medium based on isopropanol to obtain a continuous EDB coating 12 μm thick, sintered at a temperature of 850 °C for 5 h, is shown. The microstructure and morphology of the surface of the EDB coating are studied. Pt/SDC/EDB/Pt cell is used to characterize the coating conductivity. The EPD method is shown to be promising for the formation of barrier coatings based on doped bismuth oxide. The developed method can be used for creating cathode barrier layers in SOFC technology.

Mushroom production in Poland is an important and dynamically developing element of diverse agriculture. Mushroom spent compost (MSC) is major waste generated during production, i.e., MSC: mushrooms is ~5:1. To date, the main use of MSC is soil application as organic fertilizer. To date, several methods of MSC treatment have been researched and developed including production of compost, bioethanol, biogas, enzyme lactase, xylo-saccharides, and hydrogen. Torrefaction may be considered a novel approach for biomass valorization. Thus, we are pioneering the potential use of MSC valorization via torrefaction. We explored valorizing the waste biomass of MSC via thermal treatment – torrefaction (‘roasting’) to produce biochar with improved fuel properties. Here for the first time, we examined and summarized the MSC torrefaction thermogravimetric analyses, fuel properties data of raw biomass of MSC and biochars generated from MSC via torrefaction. The effects of torrefaction temperature (200~300 °C), process time (20~60 min), on fuel properties of the resulting biochars were summarized. The dataset contains results of thermogravimetric analysis (TGA) as well as proximate analyses of MSC and generated biochars. The presented data are useful in determining MSC torrefaction reaction kinetics, activation energy and to further techno-economical modeling of the feasibility of MSC valorization via torrefaction. MSC torrefaction could be exploited as part of valorization resulting from a synergy between an intensive mushroom production with the efficient production of high-quality renewable fuel.

Microbial electrochemical technologies (MET) rely on the presence of the metabolic activity of electroactive bacteria for the use of solid-state electrodes for oxidizing different kind of compound, that could lead to the synthesis of chemicals, bioremediation of polluted matrices, the treatment of contaminants of interest, as well as the recovery of energy. Keeping in mind those possibilities, since the beginning of the present century, there has been a growing interest in the use of electrochemical technologies for wastewater treatment, and if possible with simultaneous power generation. In the last years, there has been a growing interest to explore the possibility of merging MET with constructed wetlands, to offer a new option of intensified wetland system that could keep a high performance with a lower footprint. Based on that interest, this paper explains the general principles of MET, and the different known extracellular electron transfer mechanisms ruling the interaction between electroactive bacteria and potential solid-state electron acceptors. Also, the adoption of those principles for the development of MET set-ups for simultaneous wastewater treatment and power generation, and the challenges that the technology face. Ultimately, the most recent developments in set-ups that merges MET with constructed wetlands are presented and discussed.

COVID-19 highlighted the challenges of public acceptance of public health measures, including mask-wearing and vaccination. which has spurred interest in engineered approaches to reduce infections. Germicidal Ultraviolet (GUV) Energy has been used for decades in hospital rooms to limit TB transmission, but it is expensive to install in the upper part of rooms where it may be used safely. In contrast, FAR-UV energy is a relatively new, flexible technology that can be set up in rooms for moderate costs, and studies thus far indicate it is efficacious and not damaging to eyes or skin. To examine the state of the field, experts in aerosol biology, infection control, and building engineering from academia, government, and industry were convened to inform policy recommendations for future investments, identify research required, and examine policy options for using these technologies. Despite its high efficacy for deactivating several types of microorganisms and pathogens of concern, before FAR-UV technologies may be widely deployed, additional studies are needed to understand potential adverse effects, as well as the best approaches to use, standardize, and regulate the technology. In some environments, the use of FAR-UV can generate ozone, which can react with volatile organic compounds that may be hazardous to human health, such as respiratory tract irritation. Even with these concerns, the demonstrated effectiveness in disease control of both FAR-UV and longer wavelengths of GUV deserve increased policy attention to reduce risks of indoor disease transmission. While potentially useful to counter disease in high-risk indoor environments, further standardization and regulatory measures, as well as research into the production of oxidative compounds is necessary before broad adoption of FAR-UV.

Assessing handling qualities is crucial for ensuring the safety and operational efficiency of aircraft control characteristics. The growing interest in Urban Air Mobility (UAM) has increased the focus on electric Vertical Take-Off and Landing (eVTOL) aircraft; however, a comprehensive assessment of eVTOL handling qualities remains a challenge. This paper proposed a handling qualities framework to assess eVTOL handling qualities, integrating pilot compensation, task performance, and qualitative comments. An experiment was conducted, where eye-tracking data and subjective ratings from 23 participants as they performed various Mission Task Elements (MTEs) in an eVTOL simulator were recorded. The relationship between pilot compensation and task workload was investigated based on eye metrics. Data mining results revealed that pilots' eye movement patterns and workload perception change when performing Mission Task Elements (MTEs) that involve aircraft deficiencies. Additionally, pupil size, pupil diameter, iris diameter, interpupillary distance, iris-to-pupil ratio, and gaze entropy are found to be correlated with both handling qualities and task workload. Furthermore, a handling qualities and pilot workload recognition model is developed based on Long-Short Term Memory (LSTM), which is subsequently trained and evaluated with experimental data, achieving an accuracy of 97%. A case study was conducted to validate the effectiveness of the proposed framework. Overall, the proposed framework addresses the limitations of the existing Handling Qualities Rating Method (HQRM), offering a more comprehensive approach to handling qualities assessment.

The effects of toxic air in the form of air pollution are known to harm women’s health. New data has shown that air pollution has effects on maternal anemia. Yet the effects of particulate matter 2.5 (PM_2.5) on hemoglobin among reproductive maternal (15-49 years) has been understudied. In this population-based study, we study the region-specific associations between prevalence of hemoglobin among reproductive women and PM_2.5 in 43 countries of Africa from 2000-2019. Using generalized linear regression models, we found that after adjusting for key covariates, PM_2.5 had a slight negative association with hemoglobin among reproductive women. Other studies are needed in other low-income settings to expand our findings.

Unhealthy concentrations of ozone in the Uinta Basin, Utah, can occur after sufficient snowfall and a strong atmospheric anticyclone creates a persistent cold pool that traps atmospheric ozone and its precursors emitted from oil and gas operations. The winter-ozone system has two clear outcomes—occurrence or not—that is well understood by domain experts and supported by archives of atmospheric observations. Rules of the system can be formulated in natural language (“sufficient snowfall and high pressure leads to high ozone"), lending itself to analysis with a fuzzy-logic inference system. This method encodes human expertise as machine intelligence in a more constrained manner than alternative, more complex inference methods such as neural networks, increasing user trustworthiness of our model prototype before further optimization. Herein, we develop an ozone-forecasting system, Clyfar, based on knowledge of system dynamics and informed by an archive of meteorological conditions and ozone concentration. The inference system demonstrates proof-of-concept despite rudimentary tuning. We describe our framework for predicting future ozone concentrations if input values are drawn from numerical weather prediction forecasts as a proxy for observations as the system’s initial conditions. Our model is computationally cheap, allowing us to sample uncertainty with substantially more ensemble members than in traditional NWP. We evaluate hindcasts for one winter, finding our prototype demonstrates promise to deliver useful guidance for users concurrent with optimization of system parameters using machine learning.

Research interest in the occurrence, distribution, fate, and toxicity of N-(1,3-Dimethylbutyl)-N’-phenyl-p-phenylenediamine (6PPD) quinone, a derivative of the tire amino antioxidant 6PPD in urban environments, has surged. While several studies have found that 6PPD quinone exhibits acute, reproductive, and behavioral toxicity as well as mutagenicity and hepatotoxicity in aquatic and terrestrial animals, its environmental exposure data are fragmented and lack coherence across the source-to-exposure continuum, making it difficult to use for risk assessment and regulatory purposes. The present work developed an aggregate exposure pathway (AEP) framework to integrate the exposure data. An AEP network was developed for the atmospheric deposition of 6PPD quinone from tire wear in the Pearl River Delta, which led to human exposure. The 6PPD quinone research was organized, visualized, and evaluated with pertinent knowledge gaps identified using the weight of evidence assessment. Eight key exposure states were identified, with only two having high confidence levels and three having low confidence levels. Empirical support for the key transitional relationships decreased from High to Low from the source to the target site, indicating an urgent need for downstream mechanistic data. The proposed AEP framework integrated diverse 6PPD quinone research, facilitating a mechanistic understanding of the source-to-outcome continuum, as well as the development of quantitative predictive models for future research and environmental regulation.

More than 400 million tons of livestock waste are generated annually by approximately 25,000 concentrated animal feeding operations (CAFOs) located in the United States (US). These operations give rise to externalities, including adverse local and global health impacts from CAFO waste emissions, which can potentially outweigh their economic viability. However, a shortage of evidence synthesis research on US-based CAFO emissions may hinder effective policy development. This scoping review (ScR) study, conducted following guidance from the Joanna Briggs Institute, searched databases including Scopus, Web of Science, PubMed and Embase in May 2020, yielding ten publications meeting inclusion criteria. Results suggest possible CAFO worker exposures to multidrug-resistant Staphylococcus aureus (MDRSA), campylobacteriosis and cryptosporidiosis. Communities near CAFOs experienced higher rates of adverse health impacts compared to those in non-CAFO areas, with patterns suggesting proximity may correlate with increased odds of detrimental health effects. Implicit global health threats include Methicillin-resistant Staphylococcus aureus  (MRSA), MDRSA, campylobacteriosis, tuberculosis, and cryptosporidiosis. These studies provide foundational insights into CAFO proximity, density patterns, and adverse public health effects, indicating a need for evidence-informed environmental health policies to minimize local and global risks.

Objectives: Recently, desert dust in Europe has been recognized as a cardiovascular health problem. In Spain, desert dust inflows in recent years have been associated with worsening air quality. The present study examines whether desert dust events are related to the incidence of acute coronary syndrome (ACS) in patients under 55 years of age. Methods: Data from 2416 consecutive patients admitted to a tertiary hospital due to ACS were prospectively analyzed. A case-crossover time-stratified design using Poisson conditional regression models was applied to estimate the impact of desert dust events involving particulate matter concentrations of aerodynamic diameter < 10 μm (PM10) on the incidence of ACS. Results: Desert dust intrusion on days 0 to 5 after ACS onset showed no significant association with the incidence of ACS in patients under 55 years of age. The incidence rate ratios of PM10 concentrations 1, 2, 3, 3, 4 and 5 days before ACS onset (for changes of 10 µg/m3) were 1.02 (95% CI 0.97-1.1; p = 0.41), 1.01 (95% CI 0.96-1.07; p = 0.66), 0.99 (95% CI 0.94-1.05; p = 0.78), 0.96 (95% CI 0.9-1.02; p = 0.18) and 0.97 (95% CI 0.91-1.04; p = 0.41). Conclusions: Our findings suggest that desert dust is unlikely to be related to the incidence of premature coronary heart disease.

The paper describes and analyzes the performance of a new thermoelectric generation system based on the use of Peltier cells inserted in the ducts of the air conditioning equipment. The hot and cold air streams that flow in the two separated sections of an air conditioning system are used to create a thermal gradient between the two faces of the Peltier cells. Hot and cold air flow inside the A/C unit are driven to a built in thermal chamber where the Peltier cells are placed. Peltier cells are incrusted into an insulation wall that separates the two sections of the chamber through which hot and cold air streams are flowing. The so designed configuration allows the Peltier cells to generate electric current. The study has been run for constant cold air temperature and variable hot air temperature, resulting in a variable performance of the thermoelectric generator. Theoretical study has been completed with experimental tests to determine real performance of the thermoelectric unit. Efficiency of the thermoelectric generator has been found to be linearly dependent on the temperature difference between hot and cold air subsections of the chamber. Maximum efficiency, however, is limited by the hot air stream temperature, since in real conditions ambient temperature cannot overpasses a specific value. For standard operational conditions, 5º C and 45º C for the cold and hot air streams, the thermoelectric generator operates at 44% of the maximum efficiency attainable.

Pyrolysis is a combustion process of woody biomass conducted under low or no oxygen conditions. New innovations and the need to limit open burning has resulted in numerous mobile and fixed plant pyrolysis methods that burn a variety of woody residues. Production technologies that reduce the need for open burning, the main source of potential pollutants, fall under the regulations in the Clean Air Act of 1990. This Act is the legal instrument to regulate air pollution at its source across the United States of America and it is implemented and enforced through the Environmental Protection Agency, in coordination with sister agencies. One newer innovation for reducing woody residues and emissions is an air curtain incinerator. Currently, the Clean Air Act regulates stationary solid waste incinerators, and this is also applied to mobile air curtain incinerators burning woody biomass. However, other woody biochar production methods (e.g., flame cap kilns) are not subject to these regulations. Discrepancies in the interpretation of definitions related to incineration and pyrolysis and the myriad of differences related to stationary and mobile air curtain incinerators, type of waste wood from construction activities, forest residues, and other types of clean wood make the permitting regulations confusing as permits can vary by jurisdiction. This review summarizes the current policies, regulations, and directives related to in-woods biochar production and the required permits.

The increasing demand for water resources in urban areas, such as Bangladesh, due to population growth is a significant concern. One potential solution under consideration is the use of air conditioning (AC) condensate water. A study conducted at the European University of Bangladesh (EUB) focused on assessing the quality and quantity of AC condensate water from various systems. The results indicate that the collected water generally adhered to the quality standards established for drinking and household use in Bangladesh. Parameters such as pH (averaging 6.8), turbidity (1.08 NTU), total dissolved solids (TDS) (averaging 219 mg/L), iron content (0 mg/L), alkalinity (averaging 41.67 mg/L), arsenic (0 mg/L), chemical oxygen demand (COD) (averaging 3.67 mg/L), biochemical oxygen demand (BOD) (averaging 1.33 mg/L), chloride content (averaging 30.77 mg/L), and other factors were evaluated. Moreover, the AC units at EUB, varying in cooling capacity (1 ton, 2 tons, and 4 tons), produced substantial monthly volumes of 96, 177, and 354 liters of condensate water, respectively. This underscores the potential of AC condensate water as a valuable resource for addressing urban water scarcity. As a result, there is a pressing need for local decision-makers and policymakers to establish well-defined guidelines for the effective utilization of AC condensate water to mitigate water scarcity issues in urban areas.

The steel grid structure with bolted ball joints is gaining popularity in offshore platforms and aquaculture cages, but the corrosion resistance of these joints is a critical safety concern. This article introduces an innovative method to enhance the sealing performance of bolted ball joints, preventing seawater ingress and corrosion. The approach involves creating a sealed surface within the contact gap between the sleeve and connecting components. Circular grooves and sealing washers are added to both ends of the sleeve. A two-dimensional finite element analysis model of the bolted ball joint with the sealing structure was created using SOLIDWORKS and ANSYS. The study analyzes the sealing gasket's contact pressure at various compression levels and evaluates its performance with bubble tests for air tightness. Research results show a linear relationship between contact pressure and compression rate, with a sealing pressure of 5.95MPa achieved at a 14% compression rate. This simple, cost-effective sealing method effectively prevents corrosion from seawater, making it ideal for marine environments.

The cities of the future are places of sustainable mobility and a continuous reduction in the amount of harmful substances entering the surrounding environment. Current emission models are mainly dedicated to fully combustion vehicles and do not fully reflect the actual emissions of vehicles in the fleet, which is becoming increasingly diverse. The increasing share of hybrid and electric vehicles is generating the need to measure emissions and energy consumption from these vehicles and to develop new emission models that are accurate. This problem mainly concerns low-emission zones in cities, where mobility planning should be based on simulation models that are based on a continuously updated database. This work concerns the proposal of a two-dimensional model of emissions from hybrid vehicles using artificial neural networks for low-emission zones. The results can be used to further develop such emission models.

This paper describes the design and implementation of an ultrasonic non-contact air-coupled technique (UNCACT) using antisymmetric Lamb waves (ALW) for NDT assessment in novel composite sandwich plates of the car body shell. This technique is complemented with a C-Scan image implementation using this kind of guided waves. The finite element method using Comsol 6.1 is developed for the interpretation of the several wave modes presented in the experiments, including the ALW mode. The phase velocity method (PVM) is applied for the verification of the ALW mode in the portion of the RF signal necessary in the C-Scan image.

PDMS samples may be used in various microfluidic applications by hydrophilizing their surfaces. This study examines the effects of air plasma jet (APJ) and dielectric barrier discharge (DBD) plasma on the surface hydrophilicity of polydimethylsiloxane. In order to increase the hydrophilicity of PDMS sample surfaces, two plasma sources including APJ and DBD were compared. Both DBD and APJ setups were measured for voltage and current, and their respective power was calculated and compared based on their characteristics. It is important to note that the electrical specifications of APJ and DBD were identical, and the source power rates for APJ and DBD plasma were 306W and 300W respectively. UV-vis spectroscopy was used to characterize the plasma, and an electrical characterization of the plasma's power supply was carried out. The effects of parameters such as the distance from the nozzle tip, the duration of the process, and the source voltage on the hydrophilicity of the surfaces during the treatment by APJ were also examined, and samples were then examined for a period of time to determine whether surface hydrophilicity was preserved. On the PDMS surface, a contact angle of about 5.1° was observed using short-term plasma treatments of 10 seconds. In the same conditions, the effect of DBD treatment was superior to that of APJ treatment.

Recent scholarship highlights the significant environmental impact of the expanding hydraulic fracturing industry, necessitating up-to-date, comprehensive, national-scale assessments. Addressing this gap, this literature review provides a thorough analysis of the contamination and induced seismicity associated with shale-gas hydraulic fracturing in the United States. Employing systematic reviews of literature and federal reports up until July 2023, this study reveals multiple areas of concern. Notably, water and soil contamination, seismic activity, and air pollution are identified as significant challenges linked to shale gas extraction. However, ongoing studies are actively exploring remediation strategies, including advancements in monitoring and treatment technologies, aimed at mitigating the impact of contamination. These findings underscore the need for stringent regulations, continuous research, and effective management practices. This work emphasizes the importance of a collaborative approach that leverages field studies, experimental investigations, and computational advancements to ensure the responsible development of shale gas resources.

We compare photoaligning properties of polymer layers fabricated from the same constituents: polymethyl-methacrylate (PMMA) and azo-dye Disperse Red 1 (DR1), either chemically attached to the PMMA main-chain, or physically mixed with it. Photoaligning properties depend on the preparation method drastically. This finding is supported by atomic force microscope (AFM) scans monitoring the light-induced changes at the polymer−air interface, and revealing a photoinduced mass transfer.

Panama possesses multiple wetlands designated as protected areas and zones of internationally recognized importance, one amongst them, the Bahía de Panamá wetland Ramsar site, which represents approximately 21% of the national mangrove surface coverage. Due to the major ecological and economic relevance of mangrove ecosystems and their vulnerability to the effects of a changing climate it is considered necessary to perform in situ studies that evaluate the changes in sensitive meteorological parameters. This research was carried out with the objective of measuring air temperature and relative humidity values in a section of the Panama Bay wetland for the 2017-2018 period. This section, neighboring urban development projects, houses since the year 2015 the first tower for determining eddy covariance and measuring micrometeorological parameters in mangrove forests in Panama. We determined monthly and yearly mean values for the studied variables and determined the correlation between them with the use of Pearson’s correlation coefficient. Results show that both parameters still remain at tolerable levels for this type of ecosystems, with both years having very similar annual mean temperatures (27.47 ± 0.32°C for 2017 and 27.48 ± 0.67°C for 2018) and the annual mean relative humidity for 2018, being 85.35%.

Asthma is a chronic respiratory disease that impairs breathing. Management of asthma presents a significant challenge due to its inherent variability; that is, its symptoms can substantially differ among individuals, thereby complicating the prediction and management of exacerbations. Furthermore, individuals with asthma often have unique triggers that precipitate symptoms or attacks. The identification of these triggers can often prove to be a challenging, and at times, an impractical attempt. To address this, our research proposes a practical, personalized alert system, predicated on individual lung function tests conducted under varying environmental conditions classified by air-quality sensors. To validate this concept, we conducted an observational pilot study involving healthy individuals. We recruited twelve healthy participants and monitored their responses across a broad spectrum of environments, characterized by varying air quality, temperature, and humidity conditions. The lung function for each participant, assessed using peak expiratory flow (PEF) values, was recorded in each of these environments. Our results highlighted substantial variability in pulmonary responses to different environments. Utilizing these insights, we proposed a personalized alarm system that provides real-time air-quality monitoring and issues alerts when environmental conditions may potentially become unfavorable. We also explored the feasibility of employing basic machine learning techniques to predict PEF values in the aforementioned environmental conditions. This proposed system has the potential to empower individuals in actively safeguarding their respiratory health and mitigating discomfort caused by environmental conditions, especially in cases of asthma patients. By enabling timely and personalized interventions, the system aims to provide individuals with the necessary tools to minimize exposure to asthma’s possible triggers.

The design and fabrication of low-cost catalysts for highly efficient oxygen reduction is of paramount importance for various renewable energy-related technologies, such as fuel cells and metal-air batteries. Herein, we report the in situ growth of Fe3N nanoparticles encapsulated N-doped carbon nanotubes on the surface of flexible biomass-derived carbon cloth (Fe3N@CNTs/CC) via a simple one-step carbonization process. Taking advantage of its unique structure, Fe3N@CNTs/CC was employed as a self-standing electrocatalyst for oxygen reduction reaction (ORR) and possessed high activity as well as excellent long-term stability and methanol resistance in alkaline media. Remarkably, Fe3N@CNT/CC can directly play the role of both gas diffusion layer and electrocatalytic cathode in a zinc-air battery without additional means of catalyst loading, and display higher open circuit voltage, power density, and specific capacity in comparison with the commercial Pt/C catalyst. This work is anticipated to inspire the design of cost-effective, easy-preparation, and high-performance air electrodes for advanced electrochemical applications.

This paper describes the indoor air pollution in urban (Lahore, Faisalabad, Gujranwala, Rawalpindi and Karachi) Pakistani regions while considering the outdoor air and the health and wellbeing of the occupants present indoors. It also aims to assess previous methodological approaches Such as Air Conditioning Systems, used by developed countries to improve air quality to demonstrate the improvements that can be made in air quality in Pakistani urban areas. This research also investigates the causes, concentration and effects of poor air quality in Pakistani urban areas such as particulate matter (PM2.5), carbon oxides (COx), nitrogen oxides (NOx), sulphur oxides (SOx) and volatile organic compounds (VOC’s). The average concentration of these pollutants in Pakistan’s indoor air is, particulate matter (PM): [100 – 250 µg/m3 for PM2.5, 200 – 600 µg/m3 for PM10] 1 – 20 ppm for carbon monoxide (CO), nitrogen oxides (NOx): [50 – 100 µg/m3 for NO2, 20 – 40 µg/m3 for NO], 20 – 50 µg/m3 for sulfur dioxide (SO2), volatile organic compounds (VOCs): 0.1 – 0.5 ppm for formaldehyde, 5 – 10 µg/m3 for benzene and 20 – 30 µg/m3 for toluene. It should be noted that these concentrations can differ depending on the origin of pollution, location, and time of day. The literature review is made up of a combination of descriptive research methods that are used to inform the research background of ambient and indoor air quality, thus the literature review provides a theoretical and methodological background about the air pollution and its improvement in different parts of the world. According to the World Air Quality Index, Pakistan is the third most polluted country in terms of average PM2.5 concentration which is 14.2 times the WHO annual air quality guideline value. As a result, it is suggested that a PM2.5 concentration reduction program be implemented in urban Pakistani regions' indoor air.

This work presents patient radiation dose data for pediatric interventional cardiology procedures in a large hospital in Colombia. The data collection period was from April 2020 to July 2022. The local DRLs were calculated as the 3rd quartile of patient dose data distributions for kerma area-product (Pka) values. The sample of collected clinical procedures (255) was divided into diagnostic and therapeutic procedures and grouped into five weight and five age bands. The Pka differences found between diagnostic and therapeutic procedures were statistically in all weight and age bands, except the group between 1-5 years. The local DRLs were 69 Gy/cm2 (< 5 kg), 3.44 Gy/cm2 (5-<15 kg), 8.87 Gy/cm2 (15-<30 kg), 10.51 Gy/cm2 (30-<50 kg) y 22.61 Gy/cm2 (50-<80 kg), respectively. In conclusion, from comparing our results with other existing DRL values, we are similar to other centers and scope to continue optimizing the radiation dose values. This will contribute to setting national diagnostic reference levels (DRLs) for Colombia in the near future.

Air pollution is a leading cause of death in the United States, and is associated with adverse health outcomes, including increased vulnerability to coronavirus disease 2019 (COVID-19). The AirBeam2 was used to measure particulate matter with a diameter of 2.5 micrometers or smaller (PM2.5), to investigate differences between indoor and ambient levels at seven private homes in New York during and after the COVID-19 lockdown. Measurements taken in 2020 winter, spring and fall and in fall 2022 showed that 90% of the time, indoor PM2.5 levels exceeded outdoor levels both during and after the COVID-19 lockdown, p = 0.03, and exceeded safety levels. Higher indoor PM2.5 levels attributed to little or no ventilation from cooking and smoke in the kitchen and basements, were significantly greater in fall than in winter. Higher ambient PM2.5 levels were attributed to vehicular traffic at a street-facing sampling site. PM2.5 sources identified in this study may help in devising control strategies to improve indoor air quality (IAQ), and consequently alleviate respiratory health effects. These findings may be used as a basis for in-house modifications including natural ventilation and use of air purifiers to reduce exposures, mitigate future risks, and prevent potential harm to vulnerable residents.

Sowing accuracy is a critical factor in evaluating the precision of sowing equipment, and the sowing rate of the sowing equipment developed at home and abroad cannot reach 100 %, so this paper designs a seed reseeding device, aiming to improve the sowing rate secondly. Firstly, the structural composition of the seed reseeding device is introduced; secondly, according to the production object selected in this paper, kale seed (Jingfeng No.1), the best combination of factors and levels of the suction nozzle is 8 m/s inlet speed, 1.8 mm aperture, 18 mm lead and V-shaped nozzle by using orthogonal experiment; then, the EDEM software was used to conduct the vibration test, and it was found that the seed group “boils” steadily at about 15.13 mm (the depth of the reseeding tray is 23 mm), which can effectively improve the suction rate of the suction nozzle; finally, by combining the simulation results of the flow field using Fluent/ANSYS software and the spatial distribution of seeds, the number of seeds in the effective adsorption range of a single suction nozzle is about 4. The determined number of seeds, approximately 4, accounts for only 0.04% of the total number of seeds generated by the simulation. This percentage ensures high suction precision and a single seed rate, particularly under working conditions where a 72-hole tray is being sowed. In general, domestic sowing accuracy ranges from 90% to 95%. With this configuration, the purpose of improving the sowing rate twofold can be achieved.

In this contribution, unmodified silver nanoparticles were synthesized and characterized for their size and morphological properties. Thereafter, their peroxidase-like activity as the common catalytic property of silver nanoparticles was investigated by catalyzing the oxidation of 3,3’,5,5’-tetramethyl-benzidine (TMB) as peroxidase substrate, exhibiting, a specific activity as high as 5.4 µM min^-1 for the as-prepared unmodified silver nanoparticles. The stability of the catalytic activity of the as-prepared nanozymes was also checked upon their storage at ambient temperature within 7 days at different storage conditions. The results revealed that the peroxidase-like activity of unmodified silver nanoparticles was approximately retained at about 75%, and 63% after 7 days exposing daylight and air oxygen, in order. The shelf-life (storage stability) of the as-prepared nanozymes was also investigated at usual storage conditions (i.e., 4 ℃ under dark), revealed that the nanozymes saved their activity about 96% of their initial activity after 10 days of storage at 4 ℃ under dark conditions.

Increasing wind speed alleviates physiological heat strain, however, health policies have advised against using ventilators or fans under heat wave conditions with air temperatures above the typical skin temperature of 35 °C. Recent research, mostly with sedentary participants, suggests mitigating effects of wind at even higher temperatures depending on the humidity level. Our study aimed at exploring and quantifying, whether such results are transferable to moderate exercise levels, and whether the Universal Thermal Climate Index UTCI reproduces those effects. We measured heart rates, core and skin temperatures and sweat rates in 198 laboratory experiments completed by five young, semi-nude, heat-acclimated, moderately exercising males walking the treadmill with 4 km/h on the level for three hours under widely varying temperature-humidity combinations and two wind conditions. We quantified the cooling effect of increasing wind speed from 0.3 to 2 m/s by fitting generalized additive models predicting the physiological heat stress responses depending on ambient temperature, humidity and wind speed. We then compared the observed wind effects to the assessment performed by UTCI. Increasing wind speed lowered physiological heat strain for air temperatures below 35 °C, but also for higher temperatures with humidity levels above 2 kPa water vapour pressure concerning heart rate and core temperature, and 3 kPa concerning skin temperature and sweat rate, respectively. UTCI assessment of wind effects correlated positively with the observed changes in physiological responses, showing the closest agreement (r=0.9) for skin temperature and sweat rate, where wind is known for elevating the relevant convective and evaporative heat transfer. These results demonstrate the potential of UTCI for adequately assessing sustainable strategies for heat stress mitigation involving fans or ventilators depending on temperature and humidity for moderately exercising individuals.

Air conditioners are indispensable necessities in daily life and industrial production. However, the heat generation of their internal core power components can limit their performance release. In this work, we explore the application of thermoelectric coolers (TECs) in the field of power device heat dissipation through finite element simulation. First, we geometrically modeled the structure and typical operating conditions of core power devices in air conditioners. We compared the temperature fields in air cooling and TEC active cooling modes for high power consumption power devices in a 319 K operating environment. The simulation results show that in the single air cooling mode, the maximum temperature of the 173.8 W power device reaches 394.4 K and the average temperature reaches 373.9 K, which exceeds its rated operating temperature of 368.1 K. However, after adding TEC, the maximum temperature of the power device drops to 331.8 K at an operating current of 7.5 A and the average temperature of the device is 326.5 K. It indicates that TEC active cooling has a significant effect on the temperature control of the power device. At the same time, we also studied the effect of TEC working current on the temperature control effect of power devices. For TEC, there is a minimum working current of 5 A; when it is less than 5 A, TEC has no cooling effect; the cooling effect of TEC increases with an increase in working current. When the TEC working current is 10 A, the average temperature of the power device can be reduced to 292.9 K. This study has made a meaningful exploration of the application of TEC in chip temperature control and heat dissipation, providing a new solution for chip thermal management and accurate temperature control.

Background: Air-pouch balloon-assisted probes have proven to be both simple and reliable tools for intracranial pressure (ICP) monitoring. However, we experienced reproducible falsely high ICP measurement when the ICP probe was inserted in the intracerebral hematoma cavity. Thus, the aim of the experimental and translational study was to analyze the influence of ICP probe placement with regard to measured ICP values. Methods: Two Spiegelberg 3PN-sensors were simultaneously inserted into a closed drain system and were connected to two separate ICP monitors thereby allowing for simultaneous ICP measurements. This closed system was also engineered to allow for pressure to be gradually increased in a controlled fashion. Once the pressure was verified using two identical ICP probes, one of the probes was coated with blood in an effort to replicate placement within an intraparenchymal hematoma. Pressures recorded using the coated probe and control probe were then recorded and compared across a range of 0-60 mmHg. In an effort to further the translational relevance of our results two ICP probes were inserted in a patient that presented with a large basal ganglia hemorrhage that met criteria for ICP monitoring. One probe was inserted into the hematoma and the other into brain parenchyma; ICP values were recorded from both probes and the results compared. Results: The experimental set-up demonstrated a reliable correlation between both control ICP probes. Interestingly, the ICP probe covered with clot displayed a significantly higher average ICP value when compared to the control probe between 0mmHg and 50mmHg (p<0.001); at 60mmHg there was no significant difference noted. Critically, this trend in discordance was even more pronounced in the clinical setting with the ICP probe placed within the hematoma cavity having reported significantly higher ICP values as compared to the probe within brain parenchyma. Conclusion: Our experimental study and clinical pilot highlight a potential pitfall in ICP measurement that may result secondary to probe placement within hematoma. Such aberrant results may lead to inappropriate interventions in an effort to falsely addresses falsely elevated ICPs.

The purpose of this study is to characterize atmospheric pollution and its sources in two West African urban sites during the dry season (January 2009 in Bamako, Mali, and December 2009 in Dakar, Senegal). Particulate Matter (PM) source apportionment was performed using Principal Component Analysis (PCA) and Positive Matrix Factorization (PMF). Carbonaceous components, water-soluble inorganic compounds, and trace elements were analyzed from PM (TSP, PM10, and PM2.5) samples. The measured PM2.5 and PM10 concentrations were 5 to 10 times and 3 to 8 times higher than the 2005 WHO 24-hour standards, respectively. PCA and PMF analyses identify five sources in both cities. The sources contributing to aerosol concentrations (PM2.5 - PM10) in Bamako are motor vehicles (20-13%), solid fuel combustion (16-13%), crustal dust (24-30%), resuspended road dust (26-30%) and secondary aerosols (10-16%). During the sampling period in Bamako, dust was the most prevalent source, accounting for 63% of the total PM10 mass. In Dakar, the main identified sources were motor vehicles (28-19%), mineral dust (16-25%), industries and oil burn-ing (11-10%), sea salts (15-20%), and resuspended road particles (21-29%). The findings also indicate that anthropogenic emissions contribute significantly to the PM2.5 fraction, implying that populations are highly exposed to fine particles.

The general circuit topology and principles of low-noise high-voltage power supply are investigated to meet the requirements of the high-voltage bias application in air kerma meters. Two topologies, flyback converter and Royer converter are simulated using SPICE simulation program. The simulation results indicate that the circuit structure of the Royer converter is more complex, but it obtains lower output high voltage noise. While we develop an adjustable high-voltage power supply according to the circuit structure of the Royer converter, and tested it to ensure the design requirements for continuously adjustable output high-voltage linearity. The test results show that the linear adjustment rate is not more than ±0.0025%, the load regulation rate is less than ±0.1%, and the output ripple noise voltage percentage is less than 0.01%. These tested performance make it more suitable for accurate nuclear measurements.

Due to the shortage of agricultural labor forces and rapid aging of farmers, the utilization of tractors is becoming popular and essential in Korea. Tractors can be classified into two types, a walking tractor called as a power tiller and a riding tractor. In this study, agricultural tractors including walking and riding types were categorized into 4 levels by rated output power. And diesel emission inventory of tractors was established and analyzed using 2011 and 2019 survey data in Korea. Emission inventory including CO, NOx, SOx, TSP(PM10), PM2.5, VOCs and NH3 were established using Tier 3 methodology. The total amount of emission using agricultural tractors was decreased about 13% from 2011 to 2019. The number of walking tractors were decreased by about 19% in 8 years, on the other hand that of riding tractors were increased by about 12%. However, the emission reduction is about 48% for walking tractors and the emission increment is about 5% for riding tractors. Thus, the total emission from agricultural tractors was decreased by about 16% in those periods. It is due to the decrease of 21% and 15% in the hours of use of walking and riding tractors, respectively, in 2019. Walking tractors mainly emit air pollutants from spraying and transporting. Riding tractors mainly 61% of total air pollutants emits from soil preparation and transporting operations. Geographic information system (GIS) was used to spatially assign air pollutants variables into 17 provinces and metropolitan cities in Korea. High emission generating regions and changes of emissions during 8 years were clearly seen in GIS analysis. High air pollutant emitting regions are mainly located in the western and southern regions of Korea, which have plenty of arable areas compared to other regions in Korea.

In the article a statistical approach to the assessment of the emission rates discharged by the road traffic in a spatial context is proposed. It exploits an indicator, the Yearly Average Vehicle, representing the pollutant emission rate of the average vehicle belonging to a specific category, and considers the statistical variability of most of the involved traffic parameters: vehicle speed and mileage travelled in the considered time period. Finally, indicators, assessing both the most probable value among the possible emission rates and the extent of their variability range, are proposed. They may also be used to underpin decision making-processes, when the effects of different policies addressing air pollution issues, are to be evaluated. Therefore, they are suitable for the analysis supporting urban planning activities, with a view to addressing and mitigating the effects and the consequences of pollution due to the transportation sector of the urban context.

The control of air quality in museums or storages is of fundamental interest for the conservation of historic artifacts. The present work reports an example of application of RFID sensors developed in the European project SensMat and dedicated to this issue. The sensors are based on the varia-tion of property of an RFID tag coupled to a sensitive silver thin film exposed to the environment. As it will be described in the paper, such low cost sensors are interrogated by a commercial reader and provide the environmental corrosivity index and thus the presence of pollutants. The selected case study concerns the monitoring of pollution by H2S in a building dedicated to conservation and restoration of archeological and historical woods. The ability of sensors to map spatially the corrosivity within buildings is highlighted.

In large infrastructures such as dams, which have a relatively high economic value, ensuring the proper operation of the associated hydraulic facilities in different operating conditions is of utmost importance. To ensure the correct and successful operation of the dam's hydraulic equipment and prevent possible damages, including gates and downstream tunnel, to build laboratory models and perform some tests are essential (the advancement of the smart sensors based on artificial intelligence is essential). One of the causes of damage to dam bottom outlets is cavitation in downstream and between the gates, which can impact on dam facilities, and air aeration can be a solution to improve it. In the present study, six dams in different provinces in Iran has been chosen to evaluate the air entrainment in the downstream tunnel experimentally. Three artificial neural networks (ANN) based machine learning (ML) algorithms are used to model and predict the air aeration in the bottom outlet. The proposed models are trained with genetic algorithms (GA), particle swarm optimization (PSO), i.e., ANN-GA, ANN-PSO, and ANFIS-PSO. Two hydrodynamic variables, namely volume rate and opening percentage of the gate, are used as inputs into all bottom outlet models. The results showed that the most optimal model is ANFIS-PSO to predict the dependent value compared with ANN-GA and ANN-PSO. The importance of the volume rate and opening percentage of the dams' gate parameters is more effective for suitable air aeration.

The CARA program has been developed since 2008 by the French reference laboratory for air quality monitoring (LCSQA) and the regional monitoring networks to gain a better knowledge at the national level on the particulate matter (PM) chemistry and its diverse origins in urban environments. It results of strong collaborations with international-level academic partners, allowing to bring state-of-the-art, straightforward and robust results and methodologies within operational air quality stakeholders (and subsequently, decision makers). Here, we illustrate some of the main outputs obtained over the last decade thanks to this program, regarding methodological aspects (both in terms of measurement techniques and data treatment procedures) as well as acquired knowledge on the predominant PM sources. Offline and online methods are used following well-suited quality assurance and quality control procedures, notably including inter-laboratory comparison exercises. Source apportionment studies are conducted using various receptor modeling approaches. Overall, the results presented herewith underline the major influences of residential wood burning (during the cold period) and road transport emissions (exhaust and non-exhaust ones, all along the year), as well as substantial contributions of mineral dust and primary biogenic particles (mostly during the warm period). Long-range transport phenomena, e.g., advection of secondary inorganic aerosols from the European continental sector and of Saharan dust into the French West Indies, are also discussed in this paper. Finally, we briefly address the use of stable isotope measurements (δ15N) and of various organic molecular markers for a better understanding of the origins of ammonium and of the different organic aerosol fractions, respectively.

We investigate the impact of air quality and weather on the equity returns of the Shenzhen Exchange. To capture the air quality and weather effects, we use dummy variables created by employing a moving average and moving standard deviation. The important results are as follows. First, in the whole sample period (2005–2019), we find that high air pollution and extremely high temperature have significant and negative influence on the equity returns. In the sub-period I (2005–2012), the 11-day model and 31-day model show that high air pollution have significant and negative impacts on the Shenzhen stock returns. Second, the results of the quantile regression show that high air pollution have significant and negative effects during bullish market phase, and extremely high temperature have significant and negative effects during bearish market phase. This implies that the air quality and weather effects are asymmetric. Third, the weather effect of the abnormal temperature on the stock returns is greater in severe bearish market. Whereas the effect of the air pollution on the stock returns is greater in the bullish market. Fourth, the least squares method underestimates the air quality and weather effects compared to the quantile regression method, suggesting that the quantile regression method is more suitable in analyzing these effects in a very volatile emerging market such as the Shenzhen stock market.

The growing number of the accessed energy-efficient frequency conversion air conditioners is likely to generate a large number of harmonics on the power grid. The following shortage in the reactive power of peak load may trigger voltage collapse. Hence, this conflicts with people’s expectations for a cozy environment. Concerning the problems mentioned above, an active management scheme is put forward to balance the electricity use and the normal operation of air conditioning systems. To be specific, schemes to suppress the low voltage ride through (LVRT) and harmonic are designed firstly. Then to deaden the adverse effects caused by nonlinear group load running on the grid, and to prevent the unexpected accidents engendered from grid malfunction, the dynamic sensing information obtained by an online monitor is analyzed, which can be seen as an actively supervise mechanism. The combined application of active and passive filtering technology is studied as well. Thirdly, the new energy storage is accessed reliably to cope with peak-cutting or grid breaking emergencies, and the fuzzy control algorithm is researched. Finally, system feasibility is verified by functional modules co-operation simulation, and active management target is achieved under scientific and reasonable state-of-charge (SOC) management strategy.

The Sustainable Development Goals (SDGs) purport to report holistically on progress towards sustainability and do so using more than 231 discrete indicators with a primary objective to achieve a balance between the environment, social and economic aspects of development. The research question underpinning the analyses presented in this paper is: are the indicators in the SDGs sufficient and fit-for-purpose to assess the trajectory of natural resources towards sustainability? We extracted the SDG indicators that monitor the state of natural resources, or alternately support policy or governance for their protection, and determined if these are adequate to provide the essential data on natural resources to achieve the aims of the SDGs. The indicators are clustered into four natural resource categories; land, water (both marine and freshwater), air and biodiversity. Indicators for monitoring land resources show that the most comprehensive land resource indicator, for degraded land, is not fully implemented and that missing from land monitoring is an evaluation of vegetation health outside of forests and mountains, the condition of soils, and most importantly the overall health of terrestrial ecosystems. Indicators for monitoring water resources have substantial gaps, unable to properly monitor water quality, water stress, many aspects of marine resources and most significantly, the health of fresh and salt water ecosystems. Indicators for monitoring of air have recently become more comprehensive, but linkage to IPCC results would benefit both programmes. Monitoring of biodiversity is perhaps the greatest weakness of the SDG Agenda, having no comprehensive assessment even though narrow aspects are monitored. Again, deliberate linkages to other global biodiversity programmes (e.g. CBD and the Post 2020 Biodiversity Framework; IPBES; Living Planet, etc.) are recommended on condition that data can be defined at a country level. While the SDG list of indicators in support of natural resource is moderately comprehensive, it lacks holistic monitoring in relation to evaluation of ecosystems and biodiversity to the extent that these missing but vital measures of sustainability threaten the entire SDG Agenda. In addition, an emerging issue is that even where there are appropriate indicators, the amount of country-level data remains inadequate to fully evaluate sustainability. This signals the delicate balance between the extent and complexity of the SDG Agenda and uptake at a country level

We investigate the impact of air quality and weather on the stock market returns of the Shenzhen Exchange. To capture the air quality and weather effects, we apply dummy variables generated by applying a moving average and moving standard deviation. Our study provides several interesting results. First, in the whole sample period (2005–2019), we find that high air pollution and extremely high temperature have significant and negative effects on the Shenzhen stock returns. In the sub-period I (2005–2012), the 11-day model and 31-day model show that high air pollution have significant and negative effects on the Shenzhen stock returns. Second, the results of the quantile regression show that high air pollution have significant and negative effects during bullish market phase, and extremely high temperature have significant and negative effects during bearish market phase. This implies that the air quality and weather effects are asymmetric. Third, the more the Shenzhen stock returns drop, the greater the effect of the abnormal temperature is. Whereas, the more the Shenzhen stock returns increase, the greater the effect of the abnormal air quality is. Fourth, the least squares method underestimates the air quality and weather effects compared to the quantile regression method, suggesting that the quantile regression method is more suitable in analysing these effects in a very volatile emerging market such as the Shenzhen stock market.

There is accumulating evidence that prenatal exposure to air pollution disturbs fetal growth and development, but little is known about these effects in cold climates or their season-specific or joint effects. Our objective was to assess independent and joint effects of prenatal exposure to specific air pollutants on the risk of low birth weight (LBW). We utilized the 2568 children of the Espoo Cohort Study, born between 1984 and 1990, and living in the City of Espoo. We conducted stratified analyses for births during warm and cold seasons separately. We analyzed the effect estimates using multi-pollutant Poisson regression models with risk ratio (RR) as the measure of effect. The risk of LBW was related to exposure to CO and (adjusted RR 1.44, 95% CI: 1.04-2.00) and exposure to O3 in the spring-summer season (1.82, 1.11-2.96). There was also evidence of synergistic effects between CO and O3 (relative risk due to interaction, RERI, all year 1.08, 95% CI: 0.27-4.94, spring-summer 3.97, 2.17-25.85) and PM2.5 and O3 (all year 0.72, -0.07-3.60, spring-summer 2.80, 1.36-19.88). We present new evidence of both independent and joint effects of prenatal exposure in a cold climate on the risk of LBW at low levels of air pollution.

The rapid development of China's economy has led to a rapid increase in energy production and use. Among them, the excessive consumption of coal in fossil energy consumption is the leading cause of air pollution in China. This paper incorporates renewable energy innovation, fossil energy consumption and air pollution into a unified analysis framework, and uses spatial measurement models to investigate the spatial effects of renewable energy green innovation and fossil energy consumption on air pollution in China, and decomposes the total impact into direct and indirect effects. influences. The empirical results show that China's air pollution, renewable energy green innovation and fossil energy consumption are extremely uneven in geographical space, generally showing the characteristics of high in the east and low in the west, and showing a strong spatial aggregation phenomenon. Fossil energy consumption will lead to increased air pollution, and the replacement of fossil fuels with clean and renewable energy is an important means of controlling pollution emissions. The direct and indirect effects of renewable energy green innovation on air pollution are significantly negative, indicating that renewable energy green innovation not only suppresses local air pollution, but also suppresses air pollution in neighboring areas. The consumption of fossil energy will significantly increase the local air pollution, and the impact on the SO2 and Dust&Smoke pollution in the adjacent area is not very obvious. It is recommended to strengthen investment in renewable energy green innovation, reduce the proportion of traditional fossil energy consumption, and pay attention to the spatial connection and spillover of renewable energy green innovation.

Due to the accuracy of numerical calculation of fluid flow inside a hydrocyclone can be obtained using Computational Fluid Dynamics (CFD), highly modified super computers are used to simulate the fluid flow and track particle motion inside a hydrocyclone. This paper deals with the numerical study using three multiphase models viz. Volume of fluid, Mixture and Eulerian model. The dimensions of the hydrocyclone taken into consideration for numerical analysis is same as considered by Rajamani. Validation of axial and tangential velocities at different strategically decided axial stations, RMS axial and tangential velocity profiles of the hydrocyclone is done using Reynolds Stress Model (RSM). The hydrocyclone model has been designed in Creo 3.0 using the same dimensions which later was imported to CFD for meshing. Fine hexagonal mesh numbering up to 5 lacs were constructed to obtain optimum results. Fluid flow was allowed to be developed in ANSYS FLUENT 16.2. Entire simulation took 96 hours to generate results and track particle movements inside the hydrocyclone. The particle tracking has been done using three multiphase model. The first being the volume of fluid was used for validation purposes and the comparison of the Mixture and Eulerian model are the basic focus of this research work. Conclusive results indicate that usage of different multiphase model does not result in variation in particle motion. The slight variation in grade efficiency values are hardly noticeable. The Mixture model and Eulerian model predict lower separation efficiency as compared with Volume of fluid multiphase model.

Current problem facing researchers globally is microplastics as well as toxic chemical pollution of the ecosystem. Microplastics carry toxic chemicals in the ecosystem.serving as a vector for transport. In this study, a review of the literature has been conducted with the following objectives: (1) to summarise the concentrations of toxic chemicals such heavy metals and hydrophobic organic contaminants sorped on microplastics; (2) to evaluate their spatial distribution regarding adsorbed contaminant (3) to discuss plausible mechanism by which microplastics adsorp or desorp toxic chemicals in the environment; (4) to discuss implications of their occurrence in air, water and soil media; and (5) to discuss the impact of ingested microplastics to human health. Microplastics are ubiquitous environmental contaminant. Concentrations of sorped toxic chemical varied with location which represents a local problem; industrialized areas (especially areas experiencing crude oil related activities or have history of crude oil pollution) have higher concentrations than less industrialized areas. Ingestion of microplastics has been demonstrated in a range of marine and soil organisms as well as edible plants, thus possible contaminating the base of the food-web. Potential health effect to human is by particle localization, chemical toxicity and microbal toxins. We conclude by highlighting the gap in knowledge and suggesting key future areas of research for scientists and policymakers.

The Pierre Auger Observatory is the world's largest operating detection system for the observation of ultra high energy cosmic rays (UHECRs). The detector allows detailed measurements of their energy spectrum, mass composition and arrival directions of primary cosmic rays in the energy range above $10^{17}$ eV. The data collected at the Observatory over the last decade show the suppression of the cosmic ray flux at energies above $4\times10^{19}$ eV. However, it is still unclear if this suppression is caused by the propagation of cosmic rays or rather by energy limitation of their sources. The other puzzle is the origin of UHECRs. Some clues can be drawn from studying the distribution of their arrival directions. The recently observed dipole anisotropy has an orientation which indicates an extragalactic origin of UHECRs. The Auger surface detector array is also sensitive to showers due to ultra high energy neutrinos of all flavours and photons, and recent neutrino and photon limits provided by the Observatory can constrain models of the cosmogenic neutrino production and exotic scenarios of the UHECRs origin, such as the decays of super heavy particles. In this paper the recent results on measurements of the energy spectrum, mass composition and arrival directions of cosmic rays, and future prospects are presented.

The relationship between city size, coastal land use and air temperature rise with distance from coast during summer day is analyzed using the meso-scale Weather Research & Forecasting (WRF) model in five coastal cities in Japan with different sizes and coastal land use (Tokyo, Osaka, Nagoya, Hiroshima and Sendai) and inland cities in Germany (Berlin, Essen and Karlsruhe). Air temperature increased as distance from the coast increased, reached its maximum, and then decreased slightly. In Nagoya and Sendai, the number of urban land use in coastal areas is less than the other three cities, where air temperature is a little lower. As a result, air temperature difference between coastal and inland urban area is small and the curve of air temperature rise is smaller than those in Tokyo and Osaka. In Sendai, air temperature in the inland urban area is the same as in the other cities, but air temperature in the coastal urban area is a little lower than the other cities, due to about one degree lower sea surface temperature influenced by the latitude. In three German cities, the urban boundary layer may not develop sufficiently because the fetch distance is not enough.

This paper aims to investigate carbon monoxide (CO) concentrations on roadways of Karachi, potential blood levels carboxy-hemoglobin (COHb) in Karachi. Geographical information system (GIS) was used for spatial analysis of diseases potentiality while an interpolation technique has been applied for surface generation with town boundaries and later evaluates risk areas.The higher concentration of carbon monoxide in the ambient is mainly due to automobile emissions. The City center and CBD areas are more perilous.

This study examined the use of high dosages of ultraviolet germicidal irradiation (UVGI) (253.7 nm) to deal with various concentrations of air pollutants, such as formaldehyde (HCHO), total volatile organic compounds (TVOC), under various conditions of humidity. We also estimated the emission of ozone as a secondary pollutant of UVGI as treatment. A number of irradiation methods were applied for various durations in field studies to examine the efficiency of removing HCHO, TVOC, bacteria, and fungi. The removal efficiency of air pollutants (HCHO and bacteria) through long-term exposure to UVGI appears to increase with time. The effects on TVOC and fungi concentration were insignificant in the first week; however, improvements were observed in the second week. No differences were observed among the various irradiation methods in this study regarding the removal of HCHO and TVOC; however significant differences were observed in the removal of bacteria and fungi.

The airborne inoculum of Fusarium circinatum, the fungal pathogen causing Pine Pitch Canker (PPC), is one of the main means of spread of the disease in forest stands and forest nurseries. Since this world-wide known pathogen was introduced in Europe, its biology in this newly infected area still remains scarcely known. To shed more light on this topic, we set an experiment on a naturally PPC infected forest of Monterey pine in Galicia (NW Spain) with the following two goals: (i) to describe the seasonal spore dispersal pattern during one year of regular sampling and (ii) to assess the spatial spore dispersal pattern around the infested plot. Portable rotating arm spore traps were used and complemented with meteorological measurements. The abundance of F. circinatum spores in the samples was evaluated by quantitative PCR (qPCR) with hydrolysis probe. The results showed almost permanent occurrence of the air inoculum throughout the whole year, being detected in 27 of the 30 samplings. No clear temporal trends were observed, but higher air inoculum was favoured by previous lower air temperatures and lower leaf wetness. Conversely, neither rainfall nor air humidity seemed to have any significant importance. The spatial spread of the inoculum was noted to be successful up to a distance of 1000 m in the wind direction, even with winds of just 5 m s^-1. Our study shows that rotating arm spore traps combined with qPCR may be an efficient tool for F. circinatum detection.

The precise prediction of air contaminant dispersion is essential to the air quality monitoring and the emergency management of the contaminant gases leakage incidents in the chemical industry park. The conventional atmospheric dispersion models can seldom give precise prediction due to inaccurate input parameters. In order to improve the prediction accuracy of dispersion model, two data assimilation methods (i.e. one is merely based on the typical particle filter while the other is a combination of particle filter and expectation-maximization algorithm) are proposed to assimilate the UAV observations into the atmospheric dispersion model. Two emission cases are taken into consideration, the difference between which is the different dimensions of state variables. To test the performances of the proposed methods, experiments corresponding to the two emission cases are designed and implemented. The results show that the particle filter can effectively estimate the model parameters and improve the accuracy of model prediction when the dimension of state variables is low. In contrast, when the dimension of state variables becomes higher, the method of particle filter combining expectation-maximization algorithm performs better in the parameter estimation accuracy and warm-up time. Therefore, the data assimilation methods are able to effectively support the air quality monitoring and emergency management in chemical industry parks.

In the summertime, convections occur frequently over the Tibetan Plateau (TP) because of the large dynamic and thermal effects of the landmass. Measurements of vertical air velocity in convective cloud are useful for advancing our understanding of the dynamic and microphysical mechanisms of clouds and can be used to improve the parameterization of current numerical models. This paper presents a technique for retrieving high-resolution vertical air velocity from convective cloud over the TP, by using Doppler spectra from a vertically pointing Ka-band cloud radar. The method is based on the development of a “small-particle-traced” idea and the necessary data processing and uses three modes of radar. Spectral broadening corrections, uncertainty estimations, and result merging are used to ensure accurate results. Qualitative analysis of two typical convective cases shows that the retrievals are reliable and agree with the expectant results inferred from other radar measurements. A quantitative retrieval of vertical air motion from a ground-based optical disdrometer is used to preliminarily validate our radar-derived results. The comparison illustrates that while the data trends from the two methods of retrieval are similar, with the updrafts and downdrafts coinciding, cloud radar has a much higher resolution and can reveal the small-scale variation of vertical air motion.

Epiphytic lichens are well-known indicators of air contamination. The chemical composition of lichens is affected by the concentration of pollutants in the environment. Usually, researchers assess long-term variations in trace elements or other pollutants in the study area or identify the spatial features of air contamination. The aim of this study is to create a database of trace element concentrations in the samples of the epiphytic lichen Hypogymnia physodes growing in the Kaliningrad region. The database can be used as a ‘reference point’ for monitoring studies. Another objective is to identify the spatial patterns of iron, manganese, nickel, cadmium, silver, lead, strontium, rubidium, and calcium in the Kaliningrad region. The samples of wild lichens were collected from pine and birch trees 1.2-1.8 m from the bases of the threes, using a regular grid, in August 2010. One-two-year-old thalli were used in the chemical analysis. The metals Ag, Cd, Cu, Pb, Ni, Fe, Mn, and Zn were determined by AAS (Mn, Fe by flame AAS and the others by ETA-AAS) and the elements Sr, Rb, and Ca by X-ray fluorescence. The concentration of metals in the western coastal area (the Sambian or Kaliningrad Peninsula) is higher than it is in the central and eastern parts of the region. Principal component factor analysis was carried out to detect and characterise different pollution sources and to identify the most polluted areas. The factors of metal emission were described. The authors examined the features of the spatial distribution of trace elements. Prevailing winds are form south-west. Therefore, the highest concentrations of trace elements were found on the Sambian peninsula and on the coasts of the Vistula and Curonian Lagoons. The high concentrations of trace elements in the samples of the lichen H.physodes, which were observed in the coastal part of the region, are associated with human impact and subsequent pollution. The chemical composition of lichens on the Sambian peninsula may have developed under the impact of both local pollution sources – vehicles, thermal energy facilities, and ports – and such factors as transboundary traffic and sea spray.

Indoor air quality and public health have always been an area of prime interest across the globe. The significance of low-cost air quality sensing and indoor public health practices spikes during the time of pandemic and epidemics when indoor air pollution becomes a threat to living beings especially human beings. Indoor diseases are hard to diagnose if they are due to the indoor environmental conditions. A major challenge was observed in establishing a baseline between the indoor air quality sensors and associated diseases. In this work, 10,000+ articles from top literature databases were reviewed using bibliometric analysis to formulate indoor air quality sensors and diseases correlation rubrics to critically review 500+ articles. A set of 200+ articles were selected based on for detailed study based on seven bibliometric indices for publications that used WHO, NIH, US EPA, CDC, and FDA defined principles. This review has been conducted to assist end-users, public health facilities, state agencies, researchers, scientists and air quality protection agencies.

The use of natural chloride in the salt fuel has been sometimes promoted for the chlorine based molten salt fast reactor using for example NaCl-UCl4- UCl3. Most of the chemistry based R&D has been carried out on natural chloride, while in reactor physics most of the calculations are based on enriched chloride-37. In any case, the use of natural chloride (75.77% 35Cl and 24.23% 37Cl) induces specific ecological and neutron economical issues. An ecological issue is the production of 36Cl by neutron activation of 35Cl. Chlorine-36 is a soluble long live nuclide that makes it a ‘first’ nuclide in the safety assessment of the repository. We explore the build-up of 36Cl with burnup for various 37Cl (activation product) enrichment. The neutron economical aspect is gained by achieving reactor criticality with a lower amount of fissile material achieved through the use of enriched chloride-37. The criticality (k) of a core is much larger for enriched chloride than for the natural one. The reactor with 99% 37Cl would have a k99/knat of 1.04346 which would allow to reduce the required uranium enrichment and thus the fuel cost. This reactivity gain is evaluated for various 37Cl enrichment factors to estimate uranium enrichment gain achievable through 37Cl enrichment. However, from economical point of view it could be of interest to use as some kind of compromise solution natural NaCl, which will be analysed, too. Production/enrichment of 37Cl can be performed by physical separation e.g. gas centrifugation of 1H35/37Cl or by chemical separation using anion partitioning and elution of 23Na35/37Cl on solid adsorbent columns or in liquid – liquid extraction systems. These techniques require however extensive investigations including chemical thermodynamics and hydrodynamics. Comparisons are suggested on the basis of the separation factor α. Recommendations are finally given for utilising 37Cl in the fast molten salt reactor. The enrichment work for 37Cl is smaller than the work needed for 235U enrichment.

High-power output and high conversion efficiency are crucial in the study of microfluidic microbial fuel cells (MFCs). In our previous work, we attempted various methods to increase the power density of the MFCs, but nutrient consumption was limited to the bottom (electrode) layer of the microfluidic channel due to the diffusion limitations. In this work, long-term experiments were conducted on a new 4-electrode microfluidic MFC design, which grew Geobacter sulfurreducens biofilms on upward- and downward-facing electrodes in the microchannel. It was discovered that inoculation and growth of the electroactive biofilm did not proceed as fast as the downward facing anode, which we hypothesize is due to gravity effects that negatively impacted bacterial settling on that surface. Rotating the device during the growth phase resulted in uniform and strong outputs from both sides, yielding individual power densities of 4.03 and 4.13 W m-2, which was increased to nearly double when the top- and bottom-side electrodes were operated in parallel as a single 4-electrode MFC. Similarly, acetate consumption could be doubled with the 4-electrodes operated in parallel.

An emissions baseline for a city is the foundation to building an informed clean air action plan. This includes an understanding of the sources and their intensities to device cost-effective measures with the least health impacts. In an urban environment, emissions from road transport is one of the major contributors to the air pollution problem, and accounting for this sector requires a detailed profile of in-use vehicles, covering their age-mix, usage, and fuel economy. In this paper, we present a simplified framework to survey at select fuel stations to establish the necessary inputs and use them to build a localized vehicle emissions inventory. The methodology is illustrated with an application in the city of Patna, India. Here, the FuSS was employed to profile the in-use passenger vehicle characteristics by 19 trained students, over nine days and at ten fuel stations, to collect 9,775 survey points. The methodology outlined in this paper, along with the tools and training framework, is also replicable in settings other than the fuel stations.

To achieve low-cost and on-demand launches of micro satellites, the authors have been researching and developing a micro hybrid rocket since 2014. In 2018, a ballistic launch experiment was performed using the developed hybrid rocket, where it reached an altitude of about 6.2 km. The rocket engine had a 3D-printed solid fuel grain made of acrylonitrile butadiene styrene (ABS) resin in combination with a nitrous-oxide oxidizer. The fuel grain port had a star-fractal swirl geometry in order to increase the surface area of the port, to promote the laminar-turbulent transition by increasing the friction resistance, and to give a swirling velocity component to the oxidizer flow. This overcame the hybrid rocket’s drawback of low fuel regression rate; i.e., it achieved a higher fuel-gas generation rate compared with a classical port geometry. In 2021, the hybrid rocket engine was scaled up and its total impulse was increased to over 50 kNs for reaching an altitude of 15 km. In addition to the engine, other components were also improved, such as through incorporation of lightweight structures, low-shock separation devices, a high-reliability telemetry device and data logger, while keeping costs low. The rocket was launched and reached an altitude of about 10.1 km, which broke the previous Japanese altitude record of 8.3 km for hybrid rockets. The presentation will report on the developed components from the viewpoint of system design and the results of the ballistic launch experiments.

The EU’s energy targets are to achieve at least 32% renewables in the energy mix by 2030. Part of the solution is strengthening consumer rights by empowering individuals to generate their own electricity. The study aimed to identify the most suitable energy system for electricity generation of up to 50 kW in the EU residential sector. The Multi-Criteria Decision Analysis was used to compare four systems: proton exchange membrane fuel cell with photovoltaic panels, photovoltaic panels, biomass powered Stirling engine, and solar powered Stirling engine. Based on the results, the most beneficial system for household electricity generation is the Biomass-fueled Stirling engine system due to its affordability, reliability, and low environmental impact. Governments and businesses can use these findings to improve information for the residential sector and enable the transition to renewable energy.

In this research the possibility of using pH change to measure proton conductivity of proton exchange membranes (PEM) or else known as polymer electrolyte membranes are tested with using an experimental setup prepared by using pH meters. PEMs are an important part of the fuel cells and proton conductivity of the PEMs are one of the most important properties of the PEMs. Also, proton conductivity is the one of the biggest limiting factors of fuel cells thus it is important to measure the proton conductivity of the PEMs while trying new polymers or new types of membranes. But as current measurement methods do not have a standard and can be separated into mainly two different measurement methods which are Electron Impedance Spectroscopy (EIS) and Ion Exchange Capacity (IEC). EIS gives clearer results, but it needs an impedance analyzer machine, platinum electrodes and setup so this cannot be possible for every researcher due to its economical aspect. For IEC it is basically a titration method to see acid groups in the polymer or polymer matrix which are directly responsible for proton conductivity so this can show an indirect measurement of proton conductivity. But as for this one drawback are firstly this one is an indirect measurement and secondly needs overnight bath in solution can take long times. So, the possibility of using pH can be easier and both from time and economical aspect if it can be proven the give a direct relationship between pH change and proton conductivity.

This paper presents a new methodology to evaluate the performance of an electric vehicle hybrid power system consisting of a fuel cell and a supercapacitor. The study compares the results with those obtained for a battery-electric vehicle. The methodology extends to three driving modes, ECO, NORMAL, and SPORT, corresponding to conservative, moderate, and aggressive acceleration, and three driving conditions, low, medium, and high energy demand. We develop a simulation process to evaluate the energy consumption and the energy rate of a specific electric vehicle used as a prototype for the study. The methodology applies to a driving route that includes acceleration, deceleration, braking, and constant speed segments reproducing standard driving conditions in urban journeys. The proposed method considers combined driving modes, ECO, NORMAL, and SPORT, in each acceleration process, with variable fractions, 0% to 100%, for each mode. This methodology optimizes the simulation results as it fits the current driving way in urban environments. The simulation results show an average reduction in energy consumption of 37% and 27.1% in vehicle weight, contributing to lower energy use. The study concludes that using a hybrid power system, fuel cell/supercapacitor, instead of a battery in electric vehicles is beneficial, especially in journeys with frequent acceleration processes.

By 2020, over 100 countries expanded electric and plug-in hybrid electric vehicle (EV/PHEV) technologies, with global sales surpassing 7 million units. Governments are adopting cleaner vehicle technologies due to proven environmental and health implications of internal combustion engine vehicles (ICEVs), evidenced by the recent COP26 meeting. This article proposes an agent-based model of vehicle activity as a tool for quantifying energy consumption by simulating a fleet of EV/PHEVs within an urban street network at various spatio-temporal resolutions. Driver behaviour plays a significant role in fuel consumption, thus, simulating various levels of individual behaviour enhancing heterogeneity should provide more accurate results of potential energy demand in cities. The study found that 1) energy consumption is lowest when speed limit adherence increases (low variance in behaviour) and is highest when acceleration/deceleration patterns vary (high variance in behaviour) and 2) on average, for tested vehicles, EV/PHEVs were £116.33 cheaper to run than ICEVs across all experiment conditions. The difference in the average fuel costs (electricity and petrol) shrinks at the vehicle level as driver behaviour is less varied (more homogeneous). This research should allow policymakers to quantify the demand for energy and subsequent fuel costs in cities.

This paper develops a Green Light Optimal Speed Advisory (GLOSA) system for buses (B-GLOSA). The proposed B-GLOSA system is implemented on diesel buses, and field tested to validate and quantify the potential real-world benefits. The developed system includes a simple and easy to calibrate fuel consumption model that computes instantaneous diesel bus fuel consumption rates. The bus fuel consumption model, a vehicle dynamics model, the traffic signal timings, and the re-lationship between vehicle speed and distance to the intersection are used to construct an optimi-zation problem. A moving-horizon dynamic programming problem solved using the A-star algo-rithm is used to compute the energy-optimized vehicle trajectory through signalized intersections. The Virginia Smart Road test facility was used to conduct the field test on 30 participants. Each participant drove three scenarios including a base case uninformed drive, an informed drive with signal timing information communicated to the driver, and an informed drive with the recom-mended speed computed by the B-GLOSA system. The field test investigated the performance of using the developed B-GLOSA system considering different impact factors, including road grades and red indication offsets, using a split-split-plot experimental design. The test results demonstrated that the proposed B-GLOSA system can produce smoother bus trajectories through signalized in-tersections producing fuel consumption and travel time savings. Specifically, compared to the uninformed drive, the B-GLOSA system produces fuel and travel time savings of 22.1% and 6.1% on average, respectively.

Ponderosa pine is an integral part of the forested landscape in the western US; it is the dominant tree species on landscapes that provide critical ecosystem services. Moderate drought tolerance allows it to occupy the transition zone between forests and open woodlands and grasslands. Increases in stand density resulting from wildfire suppression, combined with lengthening, intensifying and more frequent droughts have resulted in reduced tree vigor and stand health in dry ponderosa pine throughout its range. To address a management need for efficient landscape-level surveys of forest health, we used Random Forests to develop an object-oriented classification of individual tree crowns (ITCs) into vigor classes using existing, agency acquired 4-band aerial imagery. Classes of tree vigor were based on quantitative physiological and morphological attributes established in a previous study. We applied our model across a landscape dominated by ponderosa pine with a variety of forest treatments to assess their impacts on tree vigor and stand health. We found that stands that were both thinned and burned had the lowest proportion of low vigor ITCs, and that stands treated before the 2014-2016 drought had lower proportions of low vigor ITCs than stands treated more recently (2016). Upland stands had significantly higher proportions of low vigor trees than lowland stands. Maps identifying the low vigor ITCs would assist managers in identifying priority stands for treatment and marking trees for harvest or retention. These maps can be created using already available imagery and GIS software.

The noble metals palladium and silver find use in many high performance applications, and their alloys (PdAg), known for more than sixty years, are industrially important, finding use in many fields including hydrogen purification and separation, numerous facets of catalysis, and in fuel cells. In recent years, interest in these materials has grown significantly, particularly in energy generating applications and due to their performance as solid-state chemical sensors for a range of small molecules. PdAg thin films can be prepared using traditional physical methods such as cold rolling, or more modern and controllable chemical or physical deposition techniques such as electrodeposition or chemical vapour deposition. Despite the wide-reaching uses of PdAg, several recent advancements in materials preparation, such as additive manufacturing, better known as 3-D printing, remain unexplored for this material due to the differing chemistries of the two elements. In this review, we explore the manufacturing methods commonly employed for the preparation of PdAg thin films, the common and niche applications of these materials, and opportunities for the future development of these two aspects, with an emphasis on how preparation of thin films can utilise additive manufacturing approaches.

Relying on Random Utility Theory (RUT) as the guiding mechanism for the Data Generating Process (DGP), this paper uses households consumption choices on cooking fuel, drinking water, and sanitation from the 2014 United States Agency for International Development's (USAID) Demographic and Health Survey (DHS) data on Burkina Faso, to characterize and investigate the inter-linkages between health consciousness and environmental consciousness, and their relationship with wealth in a low income country context. We achieve this by specifying sequentially three econometric modeling frameworks: the first one being independent binary probit (IBP) models to describe each choice process, followed by a fully parametric trivariate probit (FPTP) model to account for choice dependency, and finally by a semi-parametric trivariate probit (SPTP) model to further relax the linearity assumption. Based on the Akaike Information criteria (AIC) and the estimated Trivariate model correlation coefficients, the SPTP framework is found to be the best specification for describing the observed consumption behaviors. The results show that increased wealth level raises households health and environmental consciousness, while leaving the relative preference ordering over the elements in the household consumption basket unchanged.

Mask-wearing-induced discomfort often leads to unconscious loosening of the mask to relieve the discomfort, thereby compromising its protective efficacy. This study investigated how leakage flows affect mask-associated thermoregulation and vapor trapping to inform better mask designs. An integrated ambience-mask-face-airway model with various mask-wearing misfits was developed. The transient warming/cooling effects, thermal buoyancy force, tissue heat generation, vapor phase change, and fluid/heat/mass transfer through a porous medium were considered in this model, which was validated using Schlieren imaging, a thermal camera, and velocity/temperature measurements. Leakages from the top and side of the mask were analyzed in comparison to a no-leak scenario under cyclic respiration conditions. Results showed a significant inverse relationship between mask leakage and facial skin temperature/humidity. An equivalent impact from buoyancy forces and exhalation flow inertia was observed both experimentally and numerically, indicating a delicate balance between natural convection and forced convection that is sensitive to leakage flows and critical in thermo-humidity regulation. For a given gap, the leakage fraction was not constant within one breathing cycle, but constantly increased during exhalation. Persistently higher temperatures were found in the nose region throughout the breathing cycle in a sealed mask and were mitigated during inhalation when gaps were present. Vapor condensation occurred within the mask medium during exhalation in all mask-wearing cases. The thermal and vapor temporal variation profiles were sensitive to the location of the gap, highlighting the feasibility of leveraging temperature and relative humidity to test mask fit and quantify leakage fraction.

Climate change poses a significant risk to the environment and public health, leading to extreme weather patterns, rising sea levels, and loss of biodiversity. The relationship between air pollution from African dust and climate change demonstrates its critical role in trapping heat in the atmosphere, resulting in heat-related illnesses, heart problems, and respiratory issues. This Research points to the detrimental effects of pollutants such as smog, dust, acid rain, and ozone depletion on ecosystems, highlighting the importance of using Geographically Weighted Regression modeling and MODIS-NDVI analysis to address air pollution. Particulate Matter (PM 2.5-10) and ozone levels can have negative impacts on respiratory and cardiovascular health. Proactive steps, such as implementing clean energy technologies and enforcing stricter pollution regulations, are necessary to protect public health. Acting is crucial to addressing these global challenges and creating a cleaner, healthier future for future generations, underscoring the need for climate justice commitment.

This study examines the varying performance of low-cost sensors during seasonal smog events, particularly those resulting from solid fuel combustion linked to residential or industrial heating and other pollution sources. A prototype low-cost sensor node developed within this work was collocated for several months with reference equipment at an air quality monitoring station in the city of Ostrava (Moravian-Silesian region, Czech Republic). Deterioration of air quality during a pair of smog alert events, namely wintertime "Polish smog" episode and springtime "Saharan dust storm", which occurred through the extended period of co-location, was characterized quantitatively based on particulate matter and carbon monoxide concentrations measured by the low-cost sensors. These datasets were compared with reference data and model predictions provided by the Copernicus Atmospheric Monitoring Service. Selected low-cost sensors demonstrated linear response during Polish smog episode with highly correlated time series of carbon monoxide and particulate matter concentrations. However, when compared to reference data, the Sensirion SPS30 sensor is found to overestimate coarse particle (PM10) concentrations by the factor of two during winter evaluation period. On the other hand, oppositely biased PM10 response (underestimation by the factor of five) was determined from co-location measurement during Saharan dust storm event. This observation was attributed to combination of specific detection efficiency of the given low-cost sensor and shifts in particle size distribution due to seasonal change of ambient conditions.

Industrial buildings have numerous energy-losing equipment, such as engines, ovens, boilers, and heat exchangers. Energy losses are related to inefficient energy use and lousy work conditions for the people inside the buildings. This work is devoted to the recovery of lost energy from industrial buildings. Firstly, the residual energy of the building is extracted to be used to warm water. Consequently, the work conditions of the people inside industrial buildings can be improved by maintaining the adequate temperature. The recovery energy is done by the multipurpose heat pump system (HP system). The working fluid used in the HP system is R134a, which is a traditional and cheap working fluid. The thermophysical properties of R134a are obtained through the PC-SAFT equation of state. This work presents a performance mapping based on the intercepted areas framework to evaluate which working conditions are the optimal operating variables. The latter depends on several key parameters, such as compressor work, heat delivery, heat absorbed, and exergetic efficiency. The results show that the optimal work conditions are found at different condenser and evaporator temperatures, and that may be limited by what the designer considers a good performance of the heat pump system.

The cooling of server components has been continuously developed over the past few years in order to meet the increasing cooling requirements of server component manufacturers such as for the processor chips. The growth in performance and power density increases the cooling demand. These requirements directly influence the energy consumption and performance of the hardware. To gain a better understanding of the historical evolution and possible future technology development paths in the field of data center cooling, a patent analysis method was used. The focus is on previous and current development priorities and possible research gaps within the server and computer room levels. The European patent database was selected as data source. To determine relevant patents, the search terms for various cooling technologies were developed iteratively. After the patent extraction for the period 2000 - 2023 (earliest priority year), the search results were classified and analysed. Most of the patents deal with air or liquid cooling. In the area of liquid cooling, the focus was on direct liquid cooling, followed by total liquid cooling. Since 2015 a technological shift from air to liquid cooling can be identified on the level of patent activities. In this context, the patent groups with focus on “constructional details for different types of electric apparatus” and “electrical digital data processing” have the largest share of patents. In addition, the technology focus of the TOP 10 patent applicants was in the field of liquid cooling. In conclusion from the patent analysis, it can be derived that liquid cooling will continue to gain in importance in the future and could also be combined with other approaches in the form of hybrid cooling. However air cooling may still be relevant, even if the main cooling load is handled by liquid-based approaches. At the same time, the optimisation potential for air cooling seems to have been largely exploited in comparison to liquid cooling, as can be seen from the falling number of the patent applications.

BACKGROUND AND OBJECTIVE: The use of biomass for cooking carries significant health implications and can lead to adverse environmental issues such as deforestation, greenhouse gas emissions, and erosion. Despite these concerns, there is a lack of information about the nature and extent of cooking emissions in many developing countries. To address this gap, a study was conducted to assess cooking emission levels and their associated health effects among households in Dodoma City, Tanzania. METHODS: A descriptive cross-sectional design was conducted, involving 285 households in the peri-urban area of Dodoma City, Tanzania. A combination of questionnaires, observational checklists, and sampling devices (Aeroqual series 500 for Carbon Monoxide and Temptop PMD 351 for Particulate Matters) were employed for data collection, adhering to established protocols. Additionally, lung function tests were conducted with consent from the primary household cooks. Collected data were entered into an Excel spreadsheet and analyzed using STATA 17 software. FINDINGS: Out of 285 participants, 74.7% predominantly use charcoal for cooking, with 68.4% having outdoor kitchen setups. Significant differences in pollutant concentrations were observed across various fuel types (P=0.0001), with firewood emitting higher levels of particulate matter and carbon monoxide. Carbon monoxide concentrations during cooking were 6 times higher for firewood, 5 times higher for charcoal-gas, and 3 times higher for charcoal compared to WHO daily average limits. Additionally, a positive correlation between pollutant concentrations was noted (P-value = 0.0000). Lung problems 17.8% followed by eye irritation 15.7% were mentioned by those who claimed to know the health effects associated with cooking emissions. In addition, the spirometry test indicated that the majority of the participants had % predicted >80 while only 19% had % predicted below 50. CONCLUSION: Charcoal and firewood remain the primary cooking fuels in the study area despite their significant negative impacts. Our findings highlight a lack of awareness among community members regarding the health effects of biomass cooking emissions and insufficient guidance on constructing healthy kitchens. To address this, enforcing building standards, raising health awareness, and ensuring affordable access to modern fuels are crucial steps. These measures are essential for promoting healthier cooking practices and mitigating the adverse effects on households.

Atmospheric turbulence characteristics are essential in determining the quality of astronomical images and implementing adaptive optics systems. In this study, the vertical distributions of optical turbulence at the Peak Terskol observatory (43.27472 ° N 42.50083 ° E, 3127 m a.s.l.) using the Era-5 re-analysis and scintillation measurements are investigated. For the closest reanalysis grid node to the observatory, vertical profiles of the structural constant of the air refractive index turbulent fluctuations Cn2 were obtained. The calculated Cn2(z) vertical profiles are compared with the vertical distribution of turbulence intensity obtained from tomographic measurements with Shack-Hartmann sensor. The atmospheric coherence length at the location of Terskol Peak was estimated. Using combination of atmospheric models and scheme paramaterization of turbulence, Cn2(z) profiles at Mt. Kurapdag were obtained. The values of atmospheric coherence length at the Peak Terskol are compared with estimated values of this length at the ten astronomical sites including Ali, Lenghu and Daocheng.

Two heating surfaces with longitudinal fins are located within the closed channel inside the housing made of thermal insulation material. The air flow inside the channel was carried out by an axial fan. The heating of the fins is established by using two positive temperature coefficient heating elements (PTC). Air flows circularly from one finned surface to another, and after reaching the required temperature, it leaves the housing. In the heating system conceived in this way, a methodology based on transient thermal irreversibility of heating sources and circular air flow has been established. Volumetric air flow and circulation time within the channel were varied. The total entropy generated does not include hydraulic irreversibility, but transient thermal irreversibility of the air and heat sources. For conducting analytical modeling, the temperature of the PTC heater was considered constant at 423K and 473K. Volumetric air flow varied in the interval from 0.00001m3s-1 to 0.00006m3s-1. The experimental determination of the transient thermal entropy was performed at a much higher air flow rate of 0.005m3s-1 inside the closed channel. Due to the continuous increase in air temperature, the temperatures of both PTC heaters increased within the examined time interval of 300s. According to experimental testing, the total transient thermal entropy of the described heating system has a minimum after 175s from the start of the circular heating of the air. The minimum of transient entropy also implies the optimal time of channel opening and exit of heated air.

Background: Parkinson's disease (PD) is a global disease. However, there is a lack of research specifically focused on the AfrAbia population. Climate change, driven mainly by global warming, is linked to detrimental health impacts, including an increased frequency and intensity of heat waves. Neurological diseases, including neurodegenerative syndromes like Alzheimer's disease, Parkinson's disease, and motor neuron illnesses, have been increasingly seen and recorded in scientific literature. Although there is much literature demonstrating the growth in neurodegenerative disorders, the relationship between environmental variables such as global warming, air pollution, heavy metals, and pesticides and the higher occurrence of these illnesses is still unknown. Objective: The current article primarily aims to examine the relationship between climatic changes, air pollution, pesticides, heavy metals, and the occurrence of PD. Initially, we evaluate the influence of exposure to these variables on the cause or origin of Parkinson's disease. In addition, we will investigate how these variables disrupt processes such as excitotoxicity, oxidative stress, and neuroinflammation, all of which are strongly linked to Parkinson's disease (PD). Conclusions: This research presents a plausible rationale for the adverse effects of environmental influences on the brain, which are pivotal in the progression or onset of Parkinson's disease from an AfrAbian standpoint.

This paper deals with a method of calculating the self and mutual inductances of various air coils located arbitrarily in space. Known elementary solutions (the Biot-Savart formulas) were used to determine the magnetic field of infinitely thin current loops and infinitely thin wires of finite length linking magnetically other coils. Unlike commonly used algorithms, these elementary solutions were not extensively transformed analytically but were used to perform calculations by direct numerical integration. This enabled very quick and accurate obtaining of the self-inductance values as well as determining the dependence of mutual inductances on the position of both coils. This method allows analysis of different coil configurations (misaligned coils, inclined to each other, etc.) that other methods do not cover. It also enables the determination of the forces acting on the coils, as well as the calculation of the magnetic field distribution from any coil configuration. The obtained results were compared with those presented by other authors.

Today, air pollution is the greatest threat to organismal healthspan. The environment of our planet earth, the habitat of over eight billion humans and estimated twenty billion billions other animals, is contaminated with a wide variety of pollutants. Unfortunately, humans, out of billions and billions of living organisms on earth, are solely responsible for polluting the environment through emitting pollutants like particulate matter from industry, fuel engine vehicles, biomass combustion, toxic fumes from blasting, and wildfire. In the modern world, human-caused air pollutants induce massive oxidative stress and inflammation, the major contributors in initiation and progression of many diseases including pulmonary, cardiovascular, renal, hepatic, reproductive, neurological, mental, and accelerated biological aging. The provocative question is the following: how can we solve this human-created problem? As it is not realistic to clean the environment at once from human-caused pollution, initiatives have been undertaken to develop novel therapeutic approaches to control air-pollutant-induced oxidative stress and inflammation to protect humans from pollution-induced devastating diseases. In this article, I discuss the key findings of numerous recent preclinical studies documenting first, the role of air pollutant PM2.5 in augmentation of inflammation, oxidative stress, and associated diseases; and second, the efficacies of different natural and synthetic compounds in amelioration of PM2.5-induced oxidative stress, inflammation, pyroptosis, and associated pathologies.