This paper propose an original approach of achieving a Cymatics based visual perception of isolated speech commands. The idea is to smartly combine the effective speech processing and analysis methods with the phenomena of Cymatics. In this context, an effective approach for automatic isolated speech based message recognition is proposed. The incoming speech segment is enhanced by applying the appropriate pre-emphasis filtering, noise thresholding and zero alignment operations. The Mel-Frequency Cepstral coefficients (MFCCs), Delta coefficients and Delta-Delta coefficients are extracted from the enhanced speech segment. Later on, the Dynamic Time Warping (DTW) technique is employed to compare these extracted features with the reference templates. The comparison outcomes are used to make the classification decision. The classification decision is transformed into a methodical excitation. Finally, this excitation is converted into the systematic visual perceptions via the phenomenon of Cymatics. The system functionality is tested with an experimental setup and results are presented. The approach is novel and can be employed in various applications like visual art, encryption, education, archeology, architecture, integration of impaired people, etc.

The open communication is an exigent need for future power system where the time delay is unavoidable. In order to secure the stability of the grid, the frequency must remain within its limited range which is achieved through the load frequency control. The load frequency control signals are transmitted through communication networks which induces time delay that could destabilize the power systems. So, in order to guarantee the stability the delay margin should be computed. In this paper, we present a new method for calculating the delay margin in load frequency control systems. The transcendental time delay characteristics equation is transformed to frequency dependant equation. The spectral radius is used to find the frequencies at which the roots crosses the imaginary axis. The crossing frequencies are determined through the sweeping test and the binary iteration algorithm. A one-area load frequency control system is chosen as case study. The effectiveness of the proposed method has been proved through comparing with the most recent published methods. The method shows its merit with less conservativeness and less computations. The PI controller gains are preferable to be chosen large to reduce the damping, however, the delay margin decreases with increasing the PI controller gains.

During the recent years, there has been a tremendous increase in use of mobile phones which resulted in an increase of the exposure to electromagnetic radiations in our life. Human saliva is considered as a potential source of biomarkers to monitor changes that occur under pathological conditions. The main objective of the current experiment was to determine the effect of mobile phone radiation on general health, electrolytes and salivary function among Islamic University students who use mobile phones. A questionnaire was designed and applied to 167 healthy and 36 deaf female students to select cases whose meeting the inclusion criteria. A total of 103 students who met the inclusion criteria were included to investigate the influence of mobile phone radiations on their general health. For assessment of salivary parameters, a total of 55 students were chosen and classified into three groups. Group I was the control group, which included 17 deaf students who did not use the mobile phone at all. Group II was healthy students who have mobile phone for less than 5 years. Group III was healthy students who have mobile phone for 5 years or more. Descriptive data that included mean, standard deviation, and percentages was calculated for each group. Multiple group comparisons were made by one-way analysis of variance (ANOVA) followed by Tukey test for pairwise comparisons. Categorical data were analyzed by Chi square (χ2) test. For all the tests, a P value of 0.05 or less was considered for statistical significance. The results showed that the participants who use mobile phone had several problems in their health including dry mouth, bad odor from mouth, drooling of saliva, as well as ear and eye pain. The majority of the participants who use mobile phone complained of headache, anxiety, insomnia and forgetfulness as compared to deaf participants. Also, the study showed that there was no significant difference between salivary pH in all tested groups. Regarding to salivary flow rate, the differences were no significant in all tested groups. In addition, this study has also shown that there was significant difference between the salivary Na+ and K+ levels of the three groups. Salivary level of Na+ and K+ were significantly lower in mobile phone users when compared to non users of mobile phone.

Background: Appendicular skeletal muscle (or lean) mass (ALM) estimated using dual-energy X-ray absorptiometry (DXA) is considered to be a preferred method for sarcopenia studies. However, DXA is expensive, has limited portability, and requires radiation exposure. Bioelectrical impedance analysis (BIA) is inexpensive, easy to use, and portable; thus BIA might be useful in sarcopenia investigations. However, a large variety of models have been commercially supplied by different companies, and for most consumer products, the equations estimating ALM are not disclosed. It is therefore difficult to use these equations for research purposes. In particular, the BIA equation is often age-dependent, which leads to fundamental difficulty in examining age-related ALM loss. The aims of the current study were as follows: (1) to develop and validate an equation to estimate ALM using multi-frequency BIA (MF-BIA) based on theoretical models, and (2) to establish sarcopenia cutoff values using the equation for the Japanese population. Methods: We measured height (Ht), weight, and ALM obtained using DXA and a standing-posture 8-electrode MF-BIA (5, 50, 250 kHz) in 756 Japanese individuals aged 18 to 86-years-old (222 men and 301 women as developing equation group and 97 men and 136 women as a cross validation group). The traditional impedance index (Ht²/Z₅₀) and impedance ratio of high and low frequency (Z₂₅₀/Z₅) of hand to foot values were calculated. Multiple regression analyses were conducted with ALM as dependent variable in men and women separately. Results: We created the following equations: ALM = (0.6947 × (Ht²/Z₅₀)) + (−55.24 × (Z₂₅₀/Z₅)) + (−10,940 × (1/Z₅₀)) + 51.33 for men, and ALM = (0.6144 × (Ht²/Z₅₀)) + (−36.61 × (Z₂₅₀/Z₅)) + (−9332 × (1/Z₅₀)) + 37.91 for women. Additionally, we conducted measurements in 1624 men and 1368 women aged 18 to 40 years to establish sarcopenia cutoff values in the Japanese population. The mean values minus 2 standard deviations of the skeletal muscle mass index (ALM/Ht²) in these participants were 6.8 and 5.7 kg/m² in men and women, respectively. Conclusion: The current study established and validated a theoretical and age-independent equation using MF-BIA to estimate ALM and provided reasonable sarcopenia cutoff values.

Growing incidence of myopia worldwide justifies the search for efficient methods of myopia prevention. Numerous pharmacological, optical, and lifestyle measures have already been utilized, but there remains a need to explore more practical and predictable methods for myopia control. This paper presents a review of the latest literature on preventing the progression of myopia using Defocus Incorporated Multiple Segments Spectacle Lenses (DIMSsl), Repeated Low-level Red-Light Therapy (RLRL), and the combination of low-dose atropine (0.01%) with orthokeratology lenses.

Waveform generation as part of an on-chip built-in self-test (BIST) circuitry often necessitates sufficient linearity without expensive hardware overhead. Achieving high linearity is critical for accurate signal generation, especially in applications requiring high precision, such as biomedical and instrumentation. Currently, achieving the high linearity and precision required in signal generators often relies on costly hardware such as automated test equipment (ATE). This paper presents a DAC based hardware synthesizable arbitrary waveform generator. We use a low-cost DAC and a fully digital on-chip testing and calibration approach to nullify the effect of the DAC’s non-linearity on the generated waveform. The ultra-low cost and high linearity benefit of the proposed waveform generator makes it highly suitable for integration into resource-constrained systems. The proposed approach is validated using simulation results of the small-area DAC designed in TSMC 0.18um technology and the testing and calibration algorithms implemented in MATLAB. The DAC, designed with a matching accuracy at only the 5-bit level, is able to generate a signal with an ENOB of 12 bits alongside a SFDR and THD surpassing 100 dB. This high level of signal purity is consistently maintained across 100 Monte-Carlo simulations, demonstrating the robustness of the architecture against PVT variations as well as random mismatches.

Currently, there are few effective methods to monitor patients with gynecologic malignancies, including ovarian and endometrial cancers. The ‘tumor fraction’ of circulating tumor DNA may offer a minimally-invasive method to evaluate tumor aggressiveness via simple blood draw. To date, there is limited data on utility of ctDNA TFx interrogation in gynecologic malignancies, although there is evidence that TFx may be low or undetectable in malignancies primarily confined to the peritoneal cavity. The objective was a descriptive assessment of ctDNA TFx in a cohort of patients with ovarian and endometrial cancer. The association of TFx to continuous and categorical baseline clinicopathologic factors and progression-free survival was assessed. In a large cohort comprised of 210 plasma samples from 78 patients with biopsy-proven ovarian and endometrial cancer, plasma samples collected between 4/2018 and 4/2020 were subjected to shallow whole genome sequencing with determination of TFx. Overall, we demonstrate that TFx was low for most samples with mean TFx for ovarian cancer 5.5% and endometrial cancer 2.4%, yet can be quantified above lower limit of detection in many patients particularly when evaluating serial samples. There was no significant association between TFx level and clinical (primary vs recurrent, best response) or pathologic (e.g. histology, grade) features. Our data demonstrates low TFx levels in ovarian and endometrial cancers likely reflect that tumor types are ‘low ctDNA shed’, suggesting that higher sensitivity assessments may be required for clinical utility.

The effects of toxic air in the form of air pollution are known to harm women’s health. New data has shown that air pollution has effects on maternal anemia. Yet the effects of particulate matter 2.5 (PM_2.5) on hemoglobin among reproductive maternal (15-49 years) has been understudied. In this population-based study, we study the region-specific associations between prevalence of hemoglobin among reproductive women and PM_2.5 in 43 countries of Africa from 2000-2019. Using generalized linear regression models, we found that after adjusting for key covariates, PM_2.5 had a slight negative association with hemoglobin among reproductive women. Other studies are needed in other low-income settings to expand our findings.

Low back pain (LBP) is a significant global health issue, contributing to considerable disability and socioeconomic burdens. The degeneration of the human intervertebral disc (IVD) is a critical factor in the pathogenesis of LBP. Recent studies have emphasized the significance of its specific set of genes and extracellular matrix (ECM) in IVD health. The Noggin gene has emerged as a critical factor due to its high expression levels in healthy nucleus pulposus cells (NPCs) observed in our previous research. In this study, we investigated the hypothesis that decreased Noggin expression in NPCs is associated with IVD degeneration, contributing to LBP development. A lentivirus-mediated RNAi was applied to knockdown Noggin expression in primary NPCs from six human donors. Cell viability analysis, XTT assay, and cell apoptosis were conducted to reveal the effect after transduction. After two weeks, colony formation unit (CFU) assay was used to examine the anchor-independent growth ability of transduced cells. Additionally, qPCR was performed to quantify cellular anabolism and catabolism makers at the transcript level. The results showed lentivirus-mediated downregulation of Noggin suppressed cell growth, cell viability, and colony formation, and induced apoptosis in human NPCs in vitro. Noteworthy, it hindered cellular anabolism and enhanced catabolism activity in human NPCs after transduction. Our findings indicated that the degeneration of human IVD is possibly related to decreased Noggin expression in NPCs. This research provides valuable insights into the role of Noggin in IVD homeostasis and its implications for LBP treatment.

The present study analyses the influence of scratches and fatigue on the mechanical characteristics of aluminium alloys commonly used in the aviation industry: 2024-T4, 6061-T4, 6061-T4 uncoated, 6061-T6 uncoated, 7075-T0, and 7076-T6. 120 specimens were used for the study. Out of these, 60 samples were scratched, and the other 60 samples were also scratched under the same circumstances and then subjected to low-cycle fatigue (LCF) before undergoing the tensile test. Based on the statistical examination of the measured data, mathematical prediction models have been established. Compared to their unscratched counterparts, the results indicate a significant decrease in the mechanical properties of both scratched and scratched-fatigued sample sets. The LCF pre-treatment contributes to the negative impacts of scratches, resulting in a reduced value for the ultimate tensile strength and elongation at break. The results conclude that surface integrity plays an essential role in preserving aircraft components' structural strength.

Obesity is associated with chronic low-grade inflammation. Polyunsaturated fatty ac-ids such as omega-3 (n-3), are essential in the pro-resolution of inflammation. An 8-week double-blind randomized clinical trial was conducted with a n-6:n-3, 5:1 ratio, along with daily 1.8 g of n-3 supplementation vs. placebo. A total of 40 subjects were included, 21 in omega 3 group and 19 in placebo group. The n-3 supplementation had a superior effect compared to placebo increasing levels of Resolvin D1 [129.3 (-90.1 - 193.5) vs. -16.8 (-237.8 - 92.5) pg/mL, p=0.041], IL-10 [1.4 (-0.7 - 4.6) vs. -2.0 (-5 - 0.05) pg/mL, p=0.001], and decreasing IL-6 [-0.67 (2.72 - -0.59) vs. 0.03 (-0.59 - 1.84) pg/mL p=0.015], and MCP-1 [-29.6 (-94.9 - 5.50) vs. 18.3 (-97.3 - 66.35) pg/mL, p=0.040]. In con-clusion, n-3 supplementation promoted resolution of inflammation by increasing sys-temic levels of Resolvin D1, IL-10, and decreasing IL-6 and MCP-1.

In this paper, a low-grade copper oxide ore with highly alkaline was treated. The thermodynamic model of CuO-(NH4)2SO4-NH3-H2O was established in the leaching system of tenorite (CuO) under the condition of double conservation of mass and charge. The fitting function of MATLAB and the diff and solve functions were used to calculate the optimal ammonia concentration and total copper ion concentration of tenorite under different ammonium sulfate concentrations. The effects of different ammonia-ammonium salt (ammonium sulphate, ammonium carbonate, ammonium chloride) solution on copper leaching rate were investigated. Results show that under the conditions of ammonia concentration of 1.2 mol/L, ammonia-ammonium ratio of 2:1 and liquid-solid ratio of 3:1, the copper leaching rate from the ammonium sulphate and ammonium chloride solution reaches 70%, slightly higher than that of ammonium carbonate. Therefore, ammonia ammonium sulfate system is selected to leach low-grade copper oxide due to its lower corrosion to the equipment than the chlorination system.

The objective of this study is to investigate how different therapies modulating insulin resistance, either causally or consequently, affect metabolic parameters in treatment-naive subjects with T2DM. A total of 212 subjects were assigned to receive either a tight Japanese diet (n=65), pioglitazone at doses ranging from 15-30 mg/day (n=70), or canagliflozin at doses ranging from 50-100 mg/day (n=77) for a duration of three months. Correlations and changes (Δ) in metabolic parameters relative to insulin resistance were investigated. Across these distinct therapeutic interventions, ΔHOMA-R exhibited significant correlations with ΔFBG and ΔHOMA-B, while demonstrating a negative correlation with baseline HOMA-R. However, other parameters such as ΔHbA1c, ΔBMI, ΔTC, ΔTG, Δnon-HDL-C, or ΔUA displayed varying patterns depending on the treatment regimens. Participants were stratified into two groups based on the median value of ΔHOMA-R: the lower half (X) and upper half (Y). Group X consistently demonstrated more pronounced reductions in FBG compared to Group Y across all treatments, while other parameters including HbA1c, HOMA-B, TC, TG, HDL-C, non-HDL-C, TG/HDL-C ratio, or UA exhibited distinct regulatory responses depending on the treatment administered These findings suggest that 1) regression to the mean is observed in the changes of insulin resistance across these therapies. 2) modulation of insulin resistance with these therapies, either causally or consequentially, results in differential effects on glycemic parameters, beta-cell function, specific lipids, body weight or UA.

The use of chemical pesticides in agriculture contributes to soil, water and air pollution, biodiversity loss and can harm non-target species. The European Commission has already established a Harmonized Risk Indicator to quantify the progress in reducing the risks linked to pesticides. Therefore, there is an increasing need to promote biopesticides or so-called low-risk pesticides (LRP). Extract from Melaleuca alternifolia – tea tree oil (TTO) is known for its antiseptic, antimicrobial, antiviral, antifungal, and anti-inflammatory properties. Tea tree oil has been extensively studied in pest management as well as in the pharmaceutical and cosmetic industry and there are already products based on its active substances on the market. This review focuses on the overall evaluation of tea tree oil in terms of effectiveness and safety as a biopesticide for the first time. The collected data can be an added value for further evaluation of tea tree oil in terms of the authorization extension as a fungicide in 2026.

Ovarian cancer (OC) is an umbrella term for cancerous malignancies affecting the ovaries, yet treatment options for all subtypes are predominantly derived from high-grade serous ovarian cancer, the largest subgroup. The concept of "functional precision medicine" involves gaining personalized insights on therapy choice, based on direct exposure of patient tissues to drugs. This especially holds promise for rare subtypes like low-grade serous ovarian cancer (LGSOC). This study aims to establish an in vivo model for LGSOC using zebrafish embryos, comparing treatment responses previously observed in mouse PDX models, cell lines, and 3D tumor models. To address this goal, a well characterized patient-derived LGSOC cell line with the KRAS mutation c.35 G > T (p.(Gly12Val)) was used. Fluorescently labelled tumor cells were injected into the perivitelline space of 2 days post fertilization zebrafish embryos. At 1 day post-injection xenografts were as-sessed for tumor size, followed by random allocation into treatment groups with trametinib, luminespib, and trametinib + luminespib. Subsequently xenografts were euthanized and analysed for apoptosis and proliferation by confocal microscopy. Tumor cells formed compact tumor masses (n=84) in vivo and with clear Ki67 staining, indicating proliferation. Zebrafish xenografts exhibited sensitivity to trametinib and luminespib, individually or combined, within a two-week period, establishing them as a rapid and complementary tool to existing in vitro and in vivo models for evaluating targeted therapies in LGSOC.

To reduce the redundant counting of TDC in high-speed applications and thus reduce power consumption, a TDC architecture is proposed to quantify the difference between two adjacent rows of pixel signals. This structure can remove the identical part between two rows of pixel signals by adjusting the start and stop signal of the TDC, which will reduce the number of flipping of D flip-flops in the TDC. In the 110nm CMOS process, simulation results show that this design achieves an effective number of bits (ENOB) of 4.72 bits and a Figure of Merit (FoM) of 104.7 fJ/step - 162.3 fJ/step with a power consumption ranging from 60 µW to 93 µW. Compared with traditional counting methods, the proposed TDC can reduce counting power consumption by 30%.

C-peptide is used as a measure of endogenous insulin production. Given that insulin and C-peptide are produced in equal amounts, C-peptide is typically used to differentiate between external and endogenously produced insulin in insulin-treated type 1 diabetes mellitus (T1DM). In a clinical setting, a decline in C-peptide is regarded as a loss of beta cell function. However, physiological conditions may also be associated with low C-peptide levels. The authors of this paper use a low-carbohydrate diet, the so-called paleolithic ketogenic diet (PKD), in the treatment of various conditions and observed that C-peptide is typically low on this diet. In order to characterize C-peptide levels on this diet, we designed a study to retrospectively assess C-peptide levels in 100 non-T1DM subjects. We found that 55% of the subjects had a C-peptide level below the standard reference range. C-peptide levels correlated with glucose levels. A significant correlation was found between C-peptide and age, with younger subjects having lower C-peptide levels. Males also showed lower C-peptide levels than females. Given the increasing number of patients using low-carbohydrate diets worldwide, physicians should be aware of laboratory correlates of low-carbohydrate diets, including low C-peptide levels, most importantly to prevent incorrect T1DM diagnosis.

A millimeter-wave microstrip leaky-wave antenna array based on the substrate-integrated waveguide (SIW) and the complementary split-ring resonator (CSRR) is proposed in this paper. The slow wave characteristics of the SIW are enhanced by etching two rows of symmetrical CSRR-type slots on the surface of the SIW layer. The magnetic coupling between the CSRR-SIW layer and equally spaced circular patches array on the upper layer realizes the radiation of electromagnetic energy. In the 23~30 GHz (relative bandwidth 26.4%) operating frequency band, the horizontal polarization radiation beam scanning from -62° to -2° is realized, with a peak gain of 9.6~11.7 dBi, and the cross-polarization ratio is more than 43.8 dB.

Background: Hemangiomas are an aberrant proliferation of blood vessels and are the most frequent benign pediatric soft tissue tumors. Despite their being common, genital localisation is rare. This study aimed to assist doctors in the diagnosis, management, and treatment of paediatric vulvovaginal hemangiomas by conducting a review of the literature and also gathering some cases of patients from our clinic.Methods: We conducted a literature review including papers published between October 2021 and April 2023, and we described the cases of 3 patients who referred to our clinic with vulvovaginal hemangioma.Results: While most of hemangiomas are usually indolent and resolve with time, in some cases, especially vaginal and cervical ones, they might present with severe symptoms like heavy bleeding and need further instrumental investigation for diagnosis, like CT or MRI. As for the treatment many options are available with medical therapy or expectant management being the first choice.Conclusions: Vulvovaginal pediatric hemangiomas are rare and, so, more research should be done to how to detect and manage this lesions, especially the symptomatic and the psychologically impacting ones. For the time being treatment should personalized based also on the patient situation and clinician’s expertise.

Water scarcity challenges have necessitated the adoption of water-saving techniques in protected and nom-protected farming. This study aimed to assess the performance of a water-saving soil-less cultivation technique and to compare it with conventional soil-based cultivation in protected farming. The soilless technique used local gravel and a mixture of peat-moss, humin-substrate, and perlite in ratios of 4:3:1.5. Three irrigation regimes were imposed using emitters 8Lh-1 design discharge (D1) emitters with 6Lh-1 design discharge (D0.75) and 4Lh-1 de-sign discharge (D0.5) for the two cultivation methods during the growth cycle of tomato by drip irrigation. The vegetative growth, fruit yield and water consumption were measured and water productivity was determined. Moreover, an economic assessment was carried out by estimating and comparing economic coefficients for the two cultivation methods. Estimated coefficients include revenues, net profit, benefit-cost ratio, break-even levels of production and prices, revenues over variable cost, and revenues on investment. The tomato fruit yield under soil-based cultivation overtopped the yield under soilless cultivation. The water productivity under the soilless cultivation was almost twice that (24.3 kg m-3) of the soil-based cultivation (15.5 kg m-3). The soilless cultivation saved 50% of irrigation water applied by the conventional soil-based method, saving energy and soil from deterioration. Revenues and net profits stimulated by higher yield coupled with lower variable cos supported the soil-based cultivation. The economic assessment showed that both cultivation methods were economically viable. However, the soil-based cultivation method was more profitable due to its higher fruit yield. Overall, the results of this study suggest that the soilless cultivation technique is a viable option for wa-ter-saving cultivation. However, the soil-based cultivation method is still more profitable due to its higher fruit yield

Objective: To observe the effect of the combination of fluid-increasing decoction, low molecular heparin sodium and aspirin in the treatment of oligohydramnios in pregnancy. Methods: In this study, 114 pregnant women with oligohydramnios during pregnancy admitted to our hospital between May 2019 and March 2022 were selected as objects, and the pregnant women were equally divided into the observation group and the experimental group by random number table method, with 57 cases in each group. The observation group received conventional fluid infusion, low molecular heparin sodium and aspirin, while the experimental group was treated with fluid-increasing decoction on the basis of the observation group. The treatment effect, S/D level, amniotic fluid index, maximum vertical pocket (MVP), coagulation indexes (plasma prothrombin time (PT), plasma activated partial thromboplastin time (APTT), fibrinogen (FIB)), pregnancy outcome and adverse reactions were compared between the two groups. Results: The total effective rate of treatment was obviously better in the experimental group than that in the observation group (P＜0.05); the S/D level after treatment in the experimental group was remarkably lower than that in the observation group (P＜0.05). The amniotic fluid index and MVP were remarkably higher in the experimental group than in the observation group after treatment (P < 0.05). No significant differences in PT, APTT and FIB were found between the two groups before and after treatment (P > 0.05). The rate of oligohydramnios at delivery, cesarean section rate, neonatal weight status and preterm delivery rate were dramatically better in the experimental group than in the observation group (P < 0.05). Post-partum haemorrhage rate, neonatal asphyxia rate, amniotic fluid contamination rate and incidence of adverse events were not significantly different between the two groups of pregnant women (P > 0.05). Conclusion: The combination of fluid-increasing decoction, low molecular heparin sodium and aspirin is clinically effective and safe in the treatment of pregnant women with oligohydramnios during pregnancy. The combination is effective in reducing the S/D ratio of fetal umbilical blood flow, enhancing the amniotic fluid index and MVP in pregnant women with oligohydramnios during pregnancy, whilst not adversely influencing the coagulation function of the mother, thus contributing to a reduction in the risk of adverse pregnancy outcomes.

Controlling injection parameters is paramount when it comes to producing high-quality green parts using powder injection molding. This work combines experimental and numerical approaches to study the impact of injection parameters on mold in-cavity pressure and on the overall quality of green parts produced by low-pressure powder injection molding. The properties of two low-viscosity feedstocks (formulated from a water-atomized stainless-steel powder and wax-based binder system) were measured and implemented in an Autodesk Moldflow numerical model to quantify the molding pressures, which were finally validated using experimental real-scale injections. The results confirmed that an increase in mold temperature, an increase in feedstock temperature, and a decrease in solid loading decrease the mold in-cavity pressure, which was correlated with the feedstock viscosity. As a key result, real-scale injections confirmed that a minimum flow rate was required to avoid atypical high in-cavity pressure leading in several visual defects such as weld lines, flow marks, cracks, sinks, and incomplete filling. Due to differences in its thermal transfer properties, this flow rate threshold value decreases as the feedstock solid loading increases. For injection speeds higher than this value, the injection pressure measured experimentally was linearly correlated with the injection flow rate.

Pharmaceutical poisoning is a significant global public health concern, causing approximately 190,000 deaths yearly. This scoping review aims to comprehensively map the available literature on pharmaceutical poisoning and compare patterns between high-income countries (HICs) and low-middle-income countries (LMICs). A systematic search was performed across the following databases: Embase, PubMed, Cochrane Database of Systematic Reviews, Cochrane Central Register of Controlled Trials, and CINAHL. Studies included were from 1st January 2011 to 31st December 2020, in English, with full text available. Seventy-nine articles were included in the study; 21 were from LMICs and 58 were from HICs. The toxic exposure was largely intentional (77%) in LMICs and accidental (68%) in HICs. Drugs acting on the nervous system were responsible for 95% of toxicities worldwide with analgesics accounting for the largest subtherapeutic group in both LMICs (40%) and HICs (58%). Notable statistics were that HICs accounted for 99% of opioid overdoses, and LMICs accounted for 19% of anti-epileptic-induced toxicities. Overall, the medical outcomes of poisonings were generally worse in LMICs. The review provides possible interventions to target specific geographic locations, based on the trends identified, to reduce the burden worldwide. Many gaps within the literature were recognised, calling for more robust analytical research.

This research aims to develop an inexpensive ocean observation instrument with a project name is NOBEL (Nusantara Oceanography Backdoor Experiment Laboratory)-BOX. The device can be installed on all types of vessels and placed in a specific area to map the water conditions, providing accurate data for managing a marine area specifically to water quality. The principle of NOBEL-BOX is to attach sensors in a container connected to a microcontroller and then measure directly. The method employed includes experimental design, laboratory and field tests, and data evaluation to produce the necessary system and instruments. The design process involves the construction of the instrument and the fabrication of the device. This process includes creating three-dimensional sketches/drawings, designing microcontrollers and data transmission systems, and power capacity. The sensors attached to this device are surface water temperature, air temperature, salinity, dissolved oxygen, pH, and TDS. The testing phase includes data validation, testing of the device in the laboratory, and field testing. The laboratory and field tests showed that the device worked and provided data that can be used to analyze the seawater condition spatially and over time.

The unreliable prediction of the low frequency components from inverted acoustic impedance causes uncertainty in quantitative seismic interpretation. To address this issue, we first calculate various seismic and geological attributes that contain low frequency information, such as relative geological age, interval velocity, and integrated instantaneous amplitude. Then, we develop a method to predict the low frequency content of seismic data using these attributes, their high frequency components, and recurrent neural networks. Next, we test how to predict the low frequency components using stacking velocity obtained from velocity analysis. Using all the attributes and seismic data, we propose a supervised deep learning method to predict the low frequency components of the inverted acoustic impedance. The results obtained in both synthetic and real data cases show that the proposed method can improve the prediction accuracy of the low frequency components of the inverted acoustic impedance, with the best improvement in a real data example of 57.7% compared with the impedance predicted using well log interpolation.

This paper introduces an advanced method that integrates contingent valuation and machine learning (CVML) to estimate residents’ demand for reducing or mitigating environmental pollutions and climate change. To be precise, CVML is an innovative hybrid machine-learning model, and it can leverage a limited amount of survey data for prediction and data enrichment purposes. The model comprises of two interconnected modules: Module I, an unsupervised learning algorithm, and Module II, a supervised learning algorithm. Module I is responsible for grouping the data into groups based on common characteristics, thereby grouping the corresponding dependent variable, whereas Module II is in charge of demonstrating the ability to predict and the capacity to appropriately assign new samples to their respective category based on input attributes. Take a survey on the topic of air pollution in Hanoi in 2019 as an example, we found that CVML can predict households’ willingness– to– pay for polluted air mitigation at a high degree of accuracy (i.e., 98%). We found that CVML can help users reduce costs or save resources because it makes use of secondary data that is available on many open data sources. These findings suggest that CVML is a sound and practical method that could be widely applied in a wide range of fields, particularly environmental economics and sustainability science. In practice, CVML could be used to support decision-makers in improving the financial resources to maintain and/or further support many environmental programs in years to come.

Mercury emissions from small-scale coal-fired boilers are still a serious environmental problem in Poland and the Czech Republic. The publication presents the results of mercury emission tests conducted using five different small-scale coal-fired boilers and five different coal fuels. The research was carried out under laboratory conditions, but also using residential users' heating devices. They covered a wide range of operational parameters, both energy and emission. It was shown that more than 94% of the mercury contained in coal fuel undergoing combustion is emitted into the atmosphere with the volatile products of combustion (including dust), and the amount of emissions is strongly dependent on the original mercury content of the fuel. One solution to the problem of mercury emissions from small-scale coal-fired boilers may be to replace traditional coal with low-emission carbon fuels. The paper shows that mercury emissions from burning such fuels are many times lower than from burning coal. The widespread use of low-emission carbon fuels in individual heating systems in Poland and the Czech Republic would reduce mercury emissions to the atmosphere by up to 90% compared to the current level of emissions generated by individual heating systems in these countries.

Developing a low-cost wireless energy meter with power quality measurement for smart grid applications represents a significant advancement in efficient and accurate electrical energy monitoring.In increasingly complex and interconnected electrical systems, this device is essential in various applications, such as smart grids, enabling real-time energy usage monitoring. In such a context, smart meters expand the possibilities for sustainable and efficient energy use and promote better utilization of energy sources, especially non-renewable ones. According to the 2020 International Energy Agency (IEA) research, non-renewable energy sources represent 65% of the global total. The smart meter developed in this work is built based on the ESP32 microcontroller and easily accessible components, using a user-friendly development platform that offers a cost-effective solution while ensuring reliable performance. The main objective of the smart meter development was to enhance the software and simplify the hardware. Unlike traditional meters that perform electrical parameter calculations using complex hardware circuits, this project performed the calculations directly on the microcontroller. This approach reduced the complexity of the hardware, simplifying the meter’s design. With the high-performance processing capability of the microcontroller, efficient and accurate calculations of electrical parameters were achieved without the need for additional circuits. This software-driven approach with simplified hardware brought benefits such as reduced production costs, lower energy consumption, and increased meter development and updates flexibility. Furthermore, the integrated wireless connectivity in the microcontroller enables the transmission of collected data to remote monitoring systems for later analysis. The developed smart meter offers cost, energy efficiency, and flexibility benefits. It represents an innovative, efficient, and versatile solution for smart grid applications.

A high perovskite activity is sought for use in magnetic applications. In this paper, we present the simple synthesis of (2.5 and 5%) Tellurium-impregnated-LaCoO3 (Te-LCO), Te and LaCoO3 (LCO) by using a ball mill, chemical reduction, and hydrothermal synthesis, respectively. We also explored the structure stability along with the magnetic properties of Te-LCO. Te has a rhombohedral crystal structure, whereas Te-LCO has a hexagonal crystal system. The reconstructed Te was imbued with LCO that was produced by hydrothermal synthesis; as the concentration of the imbuing agent grew, the material became magnetically preferred. According to the X-ray photoelectron spectra, the oxidation state of the cobaltite is one that is magnetically advantageous. As a result of the fact that the creation of oxygen-deficient perovskites has been shown to influence the mixed (Te4+/2-) valence state of the incorporated samples, it is abundantly obvious that this process is of utmost significance. The TEM image confirms the inclusion of Te in LCO. The samples start out in a paramagnetic state (LCO), but when Te is added to the mixture, the magnetic state shifts to a weak ferromagnetic one. It is at this point that hysteresis occurs due to the presence of Te. Despite being doped with Mn in our prior study, rhombohedral LCO retains its paramagnetic characteristic at room temperature (RT). As a result, the purpose of this study was to determine the impacts of RT field dependency of magnetization (M-H) for Te-impregnated LCO in order to improve the magnetic properties of RT because it is a low-cost material for advanced multi-functional and energy applications.

Low-temperature accumulation is one of the essential stages in the growth process of woody ornamental plants. In this study, two different low-temperature treatments, 6℃ and 10℃, were used to analyze the effects of different low-temperature treatments on dormancy release and flowering of the 'Gulihong' plant using artificial low temperatures. Based on the experimental results, four typical early-blooming Prunus mume cultivars widely planted in Yangling area of Henan Province, China, including 'Zaoyudie', 'Zaohualve', 'Nanjing gongfen', and 'Gulihong', were selected as the experimental materials. The effects of low-temperature accumulation on the flowering characteristics of different cultivars were analyzed using a 6℃ artificial low-temperature treatment. The suitable cultivation temperature for early-blooming P. mume cultivars was screened to provide a theoretical basis for further exploration of P. mume bonsai cultivation techniques. The results showed that the flowering rate, flower diameter, flowering quantity, flowering uniformity, and bud development in the 6℃ treatment were significantly better than those in the 10℃ treatment. The flowering rate and quality of different cultivars gradually increased with the accumulation of low-temperature. Therefore, chill accumulation plays a significant role in promoting flowering quality.

Background: Low-level (LLLT) and high-intensity laser therapy (HILT) can be beneficial additions to knee osteoarthritis (KOA) rehabilitation exercises; however, it is still being determined which modality is more effective. Aim: To compare the effects of LLLT and HILT as adjuncts to rehabilitation exercise (LL+EX and HL+EX) on clinical outcomes in KOA. Methods: Thirty-four adults with mild to moderate KOA were randomly allocated to either LL+EX (n = 17) or HL+EX (n = 17) groups. All participants underwent their designated laser treatment combined with rehabilitation exercises weekly for twelve consecutive weeks. The Knee Injury and Osteoarthritis Outcome Score (KOOS), Numerical Pain Rating Scale (NPRS), active knee flexion, and Timed Up-and-Go test (TUG) were assessed at baseline and immediately post-intervention. Results: Post-intervention, both groups significantly improved their KOOS, NPRS, active knee flexion, and TUG scores compared to baseline (p &lt; 0.01). The mean difference of change in KOOS, NPRS, and active knee flexion scores for the HL+EX group surpassed the minimal clinically important difference threshold. In contrast, the LL+EX group only demonstrated clinical significance in NPRS scores. Conclusions: Incorporating HILT as an adjunct to usual KOA rehabilitation led to significantly higher improvements in pain, physical function, and knee-related disability compared to LLLT.

Hillslope and mountain roads are often the source of erosion, which in turn can lead to larger landslides and other types of mass-movements. For this reason, low-cost repeat surveys that can be done by practitioners and not solely scientists and engineers is essential. To solve this issue the present contribution shows the testing and applicability of a mix of SfM-MVS and low-cost SLAM technology to provide erosion information. The low-cost SLAM generated between 300 ~ 900 points per square meter, while SfM-MVS created between ~11,000 to 900,000 points. The density is however a trade-off against a spatially varying error, although the variability at the road-cut scale only ranges from 2 cm vertically to 2.5 cm in x,y,z based on the C2C algorithm. Furthermore, this error tends to be more important in the higher section of the cutout (further away from the sensor and at a flatter angle). It is thus possible to measure small-scale roadside change, providing that the change is in the range of >5 cm (adding the maximum potential error twice) and providing that the road-cut is such that the sensors can be brought close to the surface (camera or sensor on a pole). The authors suggest that it can be a solution for state and agencies with limited funding and that cannot afford regular laser or for roadside that are difficult to access.

Small rodents and insectivores are potential reservoirs of many pathogens transmissible to humans such as bacteria, parasites and viruses responsible for epidemics in sub-Saharan Africa, particularly in West Africa. Few studies on small mammal species in the Kolikoro and Sikasso regions are available, hence the interest in investigating the different species of small rodents and insectivores, and their role in the transmission of pathogens to humans. The study aims to identify commensal small mammal species circulating in Faladjè and Bougouni areas, and likely to represent major risks of epidemic disease emergence. Sessions of trapping were carried out in December 2016 in Faladjè and Bougouni with wire mesh traps type “Besançon tous services” (BTS) baited with peanut butter and/or onion. All animals captured were identified morphologically. Out of 123 small rodents and insectivores captured in 674 trap nights, 75 (60.97%) were from Faladjè and 48 (39.02%) from Bougouni, Of these, six species of small rodents belong to the family Muridae (Mastomys erythroleucus, Mastomys natalensis, Rattus rattus, Praomys daltoni, Gerbilliscus gambianus, Taterillus gracilis) and two species of insectivores associated with the genus Crocidura spp. belong to the family Soricidae and Erinaceidae (Crocidura cf olivieri and Atelerix cf albiventris) respectively. There is low specific diversity within these two stands, but the variation in relative abundance is significant (binomial test, p = 0.018 ˂ 0.05) between the Faladjè and Bougouni stands of small mammals. Mastomys erythroleucus was the most dominant species (57.33%, 43/75) in the Faladjè settlement and R. rattus dominated (37.5%,18/48) that of Bougouni. These two species of small mammals are potentially involved in the transmission of bacteria, parasites and pathogenic viruses to humans.

This paper addresses the difficulty of balancing real-time response and low power consumption in intelligent manhole cover application scenarios. It proposes a method to distinguish normal and abnormal events by segmenting the boundary where the acceleration of the intelligent manhole cover deviates from a set threshold and lasts for a certain period, based on the difference in vibration patterns of the intelligent manhole cover when a normal event and an abnormal event occur. This paper uses digital output motion sensor data autonomous data fusion to implement the pattern mentioned above recognition algorithm, which reduces the MCU computing and working time and the overall power consumption of the system while meeting the real-time response requirements. The test results demonstrate that the method has a high rate of anomaly recognition accuracy. The method ensures the system's real-time response capability, and the actual low power consumption test demonstrates that the device can operate continuously for 9.5 years. The low power consumption index exceeds the requirements of the existing national standard, thereby resolving the issue that it is challenging to balance intelligent manhole cover abnormality recognition and low power consumption.

Chronic pain is a source of major alterations in quality of life. It represents significant costs for health systems, and reduces the competitiveness of the working population. Vulnerability can drive the incidence of chronic pain, through its influence on modifiable risk factors, and reduced utilization of health care systems. But vulnerability can also be the consequence of a chronic pain: illness can push people into precariousness. We analysed the factors associated with pain intensity among vulnerable persons with a chronic condition, in five European countries (N=1,364). Pain was, among the whole set of variables, the main predictor of sleep problems, fatigue, depression, self-perceived health, physical and mental quality of life. This is in line with other studies showing the major impact of pain on an individual’s health and life. Multivariable analyses, adjusting for the whole set of variables, showed that women had more intense pain, as well as participants with a lower education level. These results confirm the social component in the complex etiology of pain and clearly plaid in favor of integrated care, taking into account individual characteristics and environment.

Lithium-ion batteries (LIBs) have become the preferred battery system for portable electronic devices and transportation equipment because of their high specific energy, good cycling performance, low self-discharge and no memory effect. However, too low ambient temperature will seriously affect the performance of LIBs, almost cannot discharge at -40~-60 ℃. There are many factors affecting the low temperature performance of LIBs, among which the electrode material is an important factor. Thus it is urgent to develop electrode materials or modify existing materials with excellent low temperature LIBs performance. Carbon-based anode is a kind of LIBs candidate. In recent years, it has been found that the diffusion coefficient of lithium ion in graphite anode decreases more obviously at low temperature, which is one of the important bottlenecks limiting its low temperature performance. However, the structure of amorphous carbon materials is complex, amorphous carbon materials have good ionic diffusion properties, and its grain size, specific surface area, layer spacing, structural defects, surface functional groups and doping elements may have a greater impact on the low temperature performance of the material. In this work, the low temperature performance of LIBs is obtained by modifying the carbon-based material from the perspective of electronic modulation and structural engineering.

When bone substitutes materials are used, the increased risk of infection due to the none-autogenic graft is often discussed. The treatment of large bone defects in geriatric patients, often with osteoporotic bone, often presents major challenges to surgery. Bone substitutes materials are available indefinitely without the risk of additional surgery in each patient. Can bone substitutes materials be used without hesitation in the geriatric patient?Eighty-three patients suffered traumatic fractures of the distal radius, proximal humerus, and proximal tibia. The defect zones were filled with bone substitute material based on nanocrystalline hydroxyapatite (NHA) or calcium phosphate (CP). For comparison, a reference group without the void filling with a bone graft substitute (void defects, ED) was studied. All patients over the age of 64 years were retrospectively evaluated for complications and radiological outcomes. Results: 106 patients sustained traumatic fractures of the distal radius (68.9%), proximal humerus (5.7%), and proximal tibia (22.6%). No differences in infections were found when comparing the groups (p=1.0). retrospectively evaluated. The KEM group had a nonsignificantly lower rate of pseudarthrosis (p=0.09). A relative risk (RR) reduction of complications of 32.64% was observed when bone grafting material was used. The NNT for the prevention of complications was 5.99. When bone healing was assessed by radiological images, some follow-up studies showed significant differences in fracture bridging (p<0.001).Conclusions: In contrast to previous studies, bone substitutes materials can support the healing process in geriatric patients without relevant disadvantages. With an NNT of 6 regarding complications, many patients could benefit from bone graft augmentation. No increased infection rate was observed.

When bone substitutes materials are used, the increased risk of infection due to the none-autogenic graft is often discussed. The treatment of large bone defects in geriatric patients, often with osteoporotic bone, often presents major challenges to surgery. Bone substitutes materials are available indefinitely without the risk of additional surgery in each patient. Can bone substitutes materials be used without hesitation in the geriatric patient? Eighty-three patients suffered traumatic fractures of the distal radius, proximal humerus, and proximal tibia. The defect zones were filled with bone substitute material based on nanocrystalline hydroxyapatite (NHA) or calcium phosphate (CP). For comparison, a reference group without the void filling with a bone graft substitute (void defects, ED) was studied. All patients over the age of 64 years were retrospectively evaluated for complications and radiological outcomes. Results: 106 patients sustained traumatic fractures of the distal radius (68.9%), proximal humerus (5.7%), and proximal tibia (22.6%). No differences in infections were found when comparing the groups (p=1.0). retrospectively evaluated. The KEM group had a nonsignificantly lower rate of pseudarthrosis (p=0.09). A relative risk (RR) reduction of complications of 32.64% was observed when bone grafting material was used. The NNT for the prevention of complications was 5.99. When bone healing was assessed by radiological images, some follow-up studies showed significant differences in fracture bridging (p<0.001). Conclusions: In contrast to previous studies, bone substitutes materials can support the healing process in geriatric patients without relevant disadvantages. With an NNT of 6 regarding complications, many patients could benefit from bone graft augmentation. No increased infection rate was observed.

The main aspects of material research: material synthesis, material structure, and material properties, are interrelated. Acquiring atomic structure information of electron beam sensitive materials by electron microscope, such as porous zeolites, organic-inorganic hybrid perovskites, metal-organic frameworks, is an important and challenging task. The difficulties in characterization of the structures will inevitably limit the optimization of their synthesis methods and further improve their performance. The emergence of integrated differential phase contrast scanning transmission electron microscopy (iDPC-STEM), a STEM characterization technique capable of obtaining images with high signal-to-noise ratio under lower doses, has made great breakthroughs in the atomic structure characterization of these materials. This article reviews the developments and applications of iDPC-STEM in electron beam sensitive materials, and provides an outlook on its capabilities and development.

The electronic structural evolution of LLM-105 crystal and the (101) plane of LLM-105 crystal under different pressures is investigated by the density functional theory (DFT) calculations and the surface properties of seven low-Miller-index planes of LLM-105 crystal were investigated in this study. The result demonstrates that the surface energy of (101) plane of LLM-105 is much smaller when compared with other low-Miller-index planes of LLM-105.In order to further investigate the stability of crystal structure and (101) plane of LLM-105 under different pressures, a series of pressures ranged from 0 GPa to 55 GPa were applied during the DFT calculation, and the result shows that the electronic structures of LLM-105 crystal and the (101) plane changed with the increase of external pressure and the evolution process of (101) plane is different from that of LLM-105 crystal structure.

The copper end paste used in multilayer ceramic capacitors sintered in nitrogen atmosphere will lead to carbon residue of organic vehicle, which will lead to the reduction of electrode conduc-tivity and high scrap rate. With an attempt to leave no residue in the sintering, the compatibility of solvents and thickeners should be improved because it has an important influence on the hi-erarchical volatilization and carbon residue of organic vehicles. In this work, the volatility of different solvents was compared and several solvents were mixed in a definite proportion to prepare an organic vehicle with polyacrylate resins. The hierarchical volatility and solubility parameters of mixed solvents were adjusted effectively by changing proportions of different components, the thermogravimetric curves of resins and organic vehicles were measured by thermogravimetric analyzer, the effect of solubility parameter on the dissolvability of resins in the solvent and the residual of organic vehicles were studied. Results showed that the hierar-chical volatilization of solvents can be obtained by mixing different solvents; the intrinsic vis-cosity of the organic vehicle is higher and the thermal decomposition residue of polyacrylate resins is lower when the solubility parameters of mixed solvents and polyacrylate resins are closer. The low residual sintering of organic vehicles can be achieved by using the mixed solvent with hierarchical volatility and approximate solubility parameters as resins.

Existing methods enhance mid-low resolution remote sensing ship detection by feeding super-resolved images to the detectors. Although these methods marginally improve the detection accuracy, the correlation between image super-resolution (SR) and ship detection is under-exploited. In this paper, we propose a simple but effective ship detection method called ShipSR-Det, in which both the output image and the intermediate features of the SR module are fed to the detection module. Using the super-resolved feature representation, the potential benefit introduced by image SR can be fully used for ship detection. We apply our method to the SSD and Faster-RCNN detectors and develop ShipSR-SSD and ShipSR-Faster-RCNN, respectively. Extensive ablation studies validate the effectiveness and generality of our method. Moreover, we compare ShipSR-Faster-RCNN with several state-of-the-art ship detection methods. Comparative results on the HRSC2016, DOTA and NWPU VHR-10 datasets demonstrate the superior performance of our proposed method.

Existing Reynolds Averaged Navier-Stokes based transition models do not accurately predict separation induced transition for low pressure turbines. Therefore, in this study, a novel framework based on computational fluids dynamics driven machine learning coupled with multi-expression and multi-objective optimization is explored to develop models which can improve the transition prediction for the T106A low pressure turbine at an isentropic exit Reynolds number of Re2is=100,000. Model formulations are proposed for the transfer and laminar eddy viscosity terms of the laminar kinetic energy transition model using seven non-dimensional pi groups. The multi-objective optimization approach makes use of cost functions based on the suction-side wall-shear stress and the pressure coefficient. A family of solutions is thus developed, whose performance is assessed using Pareto analysis and in terms of physical characteristics of separated-flow transition. Two models are found which bring the wall-shear stress profile in the separated region at least two times closer to the reference high-fidelity data than the baseline transition model. As these models are able to accurately predict the flow coming off the blade trailing edge, they are also able to significantly enhance the wake-mixing prediction over the baseline model.

In this letter, we show an alternative low-cost fabrication method to obtain poly(dimethyl siloxane) (PDMS) microfluidic devices. The proposed method allows the inscription of micron resolution channels on polystyrene (PS) surfaces, used as a mold for the wanted microchip’s production, by applying a high absorption coating film on the PS surface to ablate it with a focused low-power visible laser. The method allows obtaining micro resolution channels at powers between 2 and 10mW and can realize any two-dimensional polymeric devices. The effect of the main processing parameters on the channel’s geometry is presented.

There is accumulating evidence that prenatal exposure to air pollution disturbs fetal growth and development, but little is known about these effects in cold climates or their season-specific or joint effects. Our objective was to assess independent and joint effects of prenatal exposure to specific air pollutants on the risk of low birth weight (LBW). We utilized the 2568 children of the Espoo Cohort Study, born between 1984 and 1990, and living in the City of Espoo. We conducted stratified analyses for births during warm and cold seasons separately. We analyzed the effect estimates using multi-pollutant Poisson regression models with risk ratio (RR) as the measure of effect. The risk of LBW was related to exposure to CO and (adjusted RR 1.44, 95% CI: 1.04-2.00) and exposure to O3 in the spring-summer season (1.82, 1.11-2.96). There was also evidence of synergistic effects between CO and O3 (relative risk due to interaction, RERI, all year 1.08, 95% CI: 0.27-4.94, spring-summer 3.97, 2.17-25.85) and PM2.5 and O3 (all year 0.72, -0.07-3.60, spring-summer 2.80, 1.36-19.88). We present new evidence of both independent and joint effects of prenatal exposure in a cold climate on the risk of LBW at low levels of air pollution.

Central nervous system (CNS) uses vision, vestibular, and somatosensory information to maintain body stability. Research has shown that there is more lumbar proprioception error among low back pain (LBP) individuals as compared to healthy people. In this study, two groups of 20 healthy people and 20 non-specific low back pain participants (LBP) took part in this investigation. This investigation focused on somatosensory sensors and in order to alter proprioception, a vibrator (frequency of 70Hz, amplitude of 0.5 mm) was placed on the soleus muscle area of each leg and two vibrators were placed bilaterally across the lower back muscles. Individuals, whose vision was occluded, were placed on two surfaces (foam and rigid) on force plate, and trunk angles were recorded simultaneously. Tests were performed in 8 separate trials; the independent variables were vibration (4 levels) and surface (2 levels) for within subjects and 2 groups (healthy and LBP) for between subjects (4×2×2). MANOVA and multi-factor ANOVA tests were done. Linear parameters for center of pressure (COP) (deviation of amplitude, deviation of velocity, phase plane portrait (PPP), and overall mean velocity) and nonlinear parameters for COP and trunk angle ((recurrence quantification analysis) RQA and Lyapunov exponents) were chosen as dependent variables. Results indicated that NSLBP individuals relied more on ankle proprioception for postural stability. Similarly, RQA parameters for the COP on both sides and for the trunk sagittal angle indicated more repeated patterns of movement among the LBP cohort. Analysis of short and long Lyapunov exponents showed that people with LBP caused no use of all joints in their bodies (non-flexible), are less stable than healthy subjects.

Background: There are major air pollution monitoring gaps in sub-Saharan Africa. Developing capacity in the region to conduct air monitoring in the region can help estimate exposure to air pollution for epidemiology research. The purpose of our study is to develop a land use regression (LUR) model using low-cost air quality sensors developed by a research group in Uganda (AirQo). Methods: Using these low-cost sensors, we collected continuous measurements of fine particulate matter (PM2.5) between May 1, 2019 and February 29, 2020 at 22 monitoring sites across urban municipalities of Uganda. We compared average monthly PM2.5 concentrations from the AirQo sensors with measurements from a BAM-1020 reference monitor operated at the US Embassy in Kampala. Monthly PM2.5 concentrations were used for LUR modeling. We used eight Machine Learning (ML) algorithms and ensemble modeling; using 10-fold cross validation and root mean squared error (RMSE) to evaluate model performance. Results: Monthly PM2.5 concentration was 60.2 µg/m³ (IQR: 45.4-73.0 µg/m³; median= 57.5 µg/m³). For the ML LUR models, RMSE values ranged between 5.43 µg/m³ - 15.43 µg/m³ and explained between 28% and 92% of monthly PM2.5 variability. Generalized additive models explained the largest amount of PM2.5 variability (R²=0.92) and produced the lowest RMSE (5.43 µg/m³) in the held-out test set. The most important predictors of monthly PM2.5 concentrations included monthly precipitation, major roadway density, population density, latitude, greenness, and percentage of households using solid fuels. Conclusion: To our knowledge, ours is the first study to model the spatial distribution of urban air pollution in sub-Saharan Africa using air monitors developed from the region itself. Non-parametric ML for LUR modeling performed with high accuracy for prediction of monthly PM2.5 levels. Our analysis suggests that locally produced low-cost air quality sensors can help build capacity to conduct air pollution epidemiology research in the region.

The study of turbulent heat transfer in liquid metal flows has gained interest because of applications in several industrial fields. The common assumption of similarity between the dynamical and thermal turbulence, namely the Reynolds analogy, has been proven to be not valid for these fluids. Many methods have been proposed in order to overcome the difficulties encountered in a proper definition of the turbulent heat flux, such as global or local correlations for the turbulent Prandtl number or four parameter turbulence models. In this work we assess a four parameter logarithmic turbulence model for liquid metals based on RANS approach. Several simulation results considering fluids with Pr = 0.01 and Pr = 0.025 are reported in order to show the validity of this approach. The Kays turbulence model is also assessed and compared with integral heat transfer correlations for a wide range of Peclet numbers.

At least one ultrasound is recommended to predict fetal growth restriction and low birthweight earlier in pregnancy. However, in low-income countries imaging equipment and trained manpower are scarce. Hence, we developed and validated a model and risk score to predict low birthweight using maternal characteristics during pregnancy, for use in resource limited settings. We conducted a prospective cohort study among 379 pregnant women in South Ethiopia. A step-wise multivariable analysis was done to develop the prediction model. To improve clinical utility, we developed a simplified risk score to classify pregnant women at high- or low-risk of low birthweight. The accuracy of the model was evaluated using the area under the receiver operating characteristics curve (AUC) and calibration plot. We evaluated the clinical impact of the model using a decision curve analysis across various threshold probabilities. Age at pregnancy, underweight, anemia, height, gravidity, and presence of comorbidity remained in the final multivariable prediction model. The area under the receiver operating characteristics curve (AUC) of the model was 0.83 (95% confidence interval: 0.78 to 0.88). The decision curve analysis shows the model provides a higher net benefit across ranges of threshold probabilities. In general, this study showed the possibility of predicting low birthweight using maternal characteristics during pregnancy. The model could help to identify those at higher risk of having a low birthweight baby. This feasible prediction model would offer an opportunity to reduce obstetric-related complications and thus improving the overall maternal and child healthcare in low- and middle-income countries.

It has been regarded that Vibrio cholerae O1 inhabit in environmental water. As many cholera patients emerge in Kolkata, it has been thought that V. cholerae O1 is easily detected in environmental water in Kolkata. However, the detection of V. cholerae O1 is rare, though other V. cholerae (NAG Vibrio) is constantly detected. To clear the reason for the difference of the detection rate of two Vibrios, we examined the viability of V. cholera O1 and NAG Vibrios in low ionic strength aquatic medium. We observed greater declining viability of V. cholerae O1 possessing cholera toxin gene (ctx) in low ionic strength solution, but the decline of NAG Vibrios non-possessing ctx is small. To evaluate the concerning of ctx in the viability, we examined the viabilities of V. cholerae O1which do not possess ctx and NAG Vibrios possessing ctx under the same condition. The result indicated that the existence of the ctx induces the decrease the viability of the host in low ionic strength solution. The decrease observed in this experiment might relate with the low detection of V. cholerae O1 possessing ctx in environmental water, though NAG Vibrio is constantly detected.

Contemporary architects and the construction industry are trying to cope with increasing requirements concerning energy efficiency and environmental impact. One of the available options is the active utilization of energy gains from the environment, specifically solar energy gains. These gains can be utilized by, for example, solar walls and facades. The solar façade concept has been under development for more than a century. However, it hasn’t achieved widespread use for various reasons. Rather recently the concept was enhanced by the application of transparent insulation materials that have the potential to increase the efficiency of such façades. The presented study evaluates the environmental efficiency of 10 solar façade assemblies in the mild climate of the Czech Republic, Central Europe. The evaluated façade assemblies combine the principles of a solar wall with transparent insulation based on honeycomb and polycarbonate panels. The study applies Life-Cycle Assessment methodology to the calculation of environmental impacts related to the life cycle of the evaluated assemblies. The results indicate that even though there are several limiting factors, façade assemblies with transparent insulation have lower environmental impacts compared to a reference assembly with standard thermal insulation. The highest achieved difference is approx. 84% (in favour of the assembly with transparent insulation) during a modelled 50-year façade assembly service life.

Iron Doped TiO₂ nanoparticles (Fe-TiO₂) were synthesized and photocatalitically investigated under high and low fluence values of UV-radiation. The Fe-TiO₂ physical characterization was performed using X-ray Powder Diffraction (XRD), Brunauer-Emmett-Teller (BET) surface area analysis, Transmission Electron Microscope (TEM), Scanning Electron Microscope (SEM), Diffuse Reflectance Spectroscopy (DRS), and X-Ray Photoelectron Spectroscopy (XPS) technique. The XPS evidenced that ferric ion (Fe³⁺) was in the lattice of TiO₂ and co-dopants no intentionally added were also present due to the precursors of the synthetic method. The Fe³⁺ concentration played a key role in the photocatalytic generation of hydroxyl radical (•OH) and estriol (E3) degradation. Fe-TiO₂ materials accomplished E3 degradation, and it was found that the catalyst with 0.3 at. % content of Fe (0.3 Fe-TiO₂) enhanced the photocatalytic activity under low UV-irradiation compared with no intentionally Fe-added TiO₂ (zero-iron TiO₂) and Aeroxide^® TiO₂ P25. Furthermore, the enhanced photocatalytic activity of 0.3 Fe-TiO₂ under low UV-irradiation may have applications when radiation intensity must be controlled, as in medical applications, or when strong UV absorbing species are present in water.

Global warming and climate change have led to extreme changes in climatic conditions in recent years. The Taiwan government designates the construction of the Kinmen County as low carbon islands, to promote the operation of 100 electric motorcycles and battery demonstration. This study combined with island tourism, after boarding the island, visitors can rent electric motorcycles from the passenger service center and coordinate with the island tour map to show the location of the battery exchange points, so as to facilitate the search. During the operation, the amount of electric motorcycle lease is 15,551 times, the total mileage of motor vehicle is 284,404 km, the number of battery exchange is 622 times, the lease income is about NT$900,000. To reduce carbon and economic benefits of the assessment, compared to the motorcycles (50 c.c), electric motorcycles (EM 100) can reduce the carbon emissions by 8,726 kg, reducing energy costs of NT$422,594.

Metal-Organic Frameworks (MOFs) are a subclass of porous materials that have unique properties such as varieties of structures from different metals and organic linkers, tunable porosity from a structure or framework design, etc. Moreover, modification/functionalization of the material structure could optimize the material properties and demonstrate high potential for a selected application. MOF materials exhibit exceptional properties and make these materials widely applicable including in energy storage and heat transformation applications. This review aims to give a broad overview of MOFs and their development as adsorbent materials having the potential for heat transformation applications. We summarize current investigations, developments, and possibilities of metal-organic frameworks (MOFs) especially the tuning of the porosity and hydrophobic/hydrophilic design required for this specific application. These materials applied as adsorbent are promising in the thermal driven adsorption for heat transformation using water as working fluid and related application.

The present study examined and compared the effects of high- and low-molecular weight (MW) chitosan, a nutraceutical, on intestinal and liver lipid metabolism in rats fed with high-fat diet. Both high- and low-MW chitosan decreased liver weight, elongated small intestine, improved the dysregulation of blood lipids and liver fat accumulation, and increased fecal lipid excretion in high-fat diet-fed rats. Supplementation of both high- and low-MW chitosan significantly inhibited the decreased phosphorylated AMP-activated protein kinase (AMPK)α and peroxisome proliferator-activated receptor (PPAR)α protein expressions and the increased lipogenesis/cholesterogenesis-associated protein expressions (sterol regulatory element binding protein (SREBP)1c, SREBP2, and PPARγ) and the decreased apolipoprotein (Apo)E and microsomal triglyceride transfer protein (MTTP) protein expressions in the livers of high-fat diet-fed rats. Both high and low-MW chitosan supplementation could also suppress the increased MTTP protein expression and the decreased angiopoietin-like protein (Angptl)4 protein expression in the intestines of high-fat diet-fed rats. Comparison between high and low-MW chitosan, high-MW chitosan has a higher efficiency than low-MW chitosan on the inhibition of intestinal lipid absorption and the increase of hepatic fatty acid oxidation, which can improve liver lipid biosynthesis and accumulation.

The effect of the acetylene and hydrogen gases mixture ratios in direct low-temperature vacuum carburization was investigated. The gas ratio is an important parameter for producing the free radicals in the carburization. The free radicals can remove the natural oxide film by the strong reaction of the hydrocarbons, and then thermodynamically activity can be increased. When the gas ratio was below 1, the supersaturation expanded austenite layers were formed on the surface of the AISI 316L stainless steel, which had the maximum carbon solubility up to 11.5 at.% at 743 K, were formed. On the other hand, when the gas ratio was above 1, the carbon concentration of them remained low even if the process time was enough increased to reach the maximum carbon solubility. As a result, the carbon concentration underneath the surface was determined to be highly dependent on the gas mixture ratio of acetylene and hydrogen. In conclusion, it is necessary to restrict the ratio of acetylene and hydrogen gases to total mixture gases to form the expanded austenite layer with the high carbon concentration in the direct low-temperature vacuum carburization.

Clinical rehabilitation and sports performance analysis both require the objectification of movement. Kinovea^© is a free 2D motion analysis software that enables the establishment of kinematics parameters. This low-cost technology has been used in sports sciences, as well as clinical field and research work. Although it has been validated as a tool with which to assess time-related variables, this is not yet the case regarding angular and distance variables. The main objective of this study was to determine the validity and reliability of the Kinovea software in obtaining angular and distance data at different perspectives of 90°, 75°, 60° and 45°. For this purpose, a figure with 29 points was designed (in AutoCAD) and 24 frames analysed. Each frame was examined by three observers who each made two attempts. For each export data item, 20 angles and 20 distance variables were calculated, with intra- and inter-observer reliability also analysed. To evaluate Kinovea reliability and validity a multiple approach was applied involving the following analysis: -systematic error with a two-way ANOVA 2x4; -relative reliability with ICC and CV (95% confidence interval); -absolute reliability with Standard Error. The results thus obtained indicate that the Kinovea software is a valid and reliable tool that is able to measure accurately at distances up to 5 m from the object and at an angle range of 90°–45°. Nevertheless, for optimum results an angle of 90° is suggested.

Continued high rates of both under- and over-nutrition in low- and low-middle-income countries highlight the importance of understanding dietary practices such as early and exclusive breastfeeding, and dietary patterns such as timely, appropriate complementary feeding—these behaviors that are rooted in complex cultural ecologies. A systematic review and synthesis of available qualitative research related to infant and young child dietary patterns and practices from the perspective of parents and families in low income settings is presented, with a focus on barriers and facilitators to achieving international recommendations. Data from both published and grey literature from 2006-2016 was included in the review. Quality assessment consisted of two phases (CASP guidelines and assessment using GRADE-CERQual), followed by synthesis of the studies identified, and subsequent thematic analysis and interpretation. The findings indicated several categories of both barriers and facilitators, spanning individual and system level factors. The review informs efforts aimed at improving child health and nutrition, and represents the first such comprehensive review of the qualitative literature, uniquely suited to understanding complex behaviors leading to infant and young child dietary patterns.

The creep behaviors of TA2 and R60702 at low and intermediate temperature were presented and discussed in this paper. Experimental results indicated that an apparent threshold stress exhibited in the creep deformation of R60702. Meanwhile, the primary creep phase was found as the main pattern in the room temperature creep behavior of TA2. Compared with exponential law, the power law has been proved to be a proper constitutive model in the description of primary creep phase. It also showed that θ projection method had its significant advantage in the evaluation of accelerated creep stage. Thus, a composite model which combined power law with θ projection method was applied in the creep curves evaluation at low and intermediate temperature. Based on the multiaxial creep deformation results, the model was modified and discussed. A linear relationship existed between composite model parameters and applied load. Finally, the creep life could be accurately predicted and the composite model method is suitable for application in low and intermediate temperature creep life analysis.

In small-scale hydropower scheme, the most important component is electro-mechanical equipment. Since cost contribution of this component is high because hydrokinetic projects require negligible civil works. Turbine and alternator contribute major fraction of the hydrokinetic projects. Thus, there is a requirement to estimates the electromechanical equipment cost for the hydrokinetic hydropower scheme. The present paper investigates design parameters of the hydrokinetic turbines and intends to develop cost correlation which depends on most critical parameters of hydropower sites such as velocity and power capacity. In this present work, three zero head turbines are considered including straight blade Darrieus, two Stage Savonius, and Gorlov Helical. The size and cost of major components have been calculated based on material, manufacturing, research and design, and assembly costs. Based on cost and site parameters, cost correlation has been developed. The obtained cost has been validated with available zero head turbines in the market and installed projects. A techno-economic analysis has been carried out to select economical hydrokinetic turbine for river and canal application.

Background/Objectives: Intervertebral disc degeneration is the most common cause of low back pain (LBP) and lumbosciatica is a major challenge to healthcare systems worldwide. For years, ozone therapy has been used with excellent results in intervertebral disc disease and in patients with LBP. In vitro studies have demonstrated the positive action of porcine collagen in extracellular matrix remodeling and homeostasis. These tissue changes, associated with LBP, may suggest an indication for combined ozone/collagen treatment in patients with LBP. However, no studies have been reported regarding this combination of treatments. Methods: The present work compared, retrospective data of two treatment groups (each of 10 LBP patients): A) Oxygen-Ozone Therapy (OOT) vs. B) OOT plus porcine collagen type 1 injections (COL I). Pain intensity and physiological function were assessed by the numerical rating scale (NSR) method. The Roland-Morrison questionnaire was used to assess disability. Patient data were acquired before, during and at six months of follow-up. Significant differences were assessed by ANOVA and T-Student test. Results: The analyses revealed significant statistical differences comparing the two arms, where, the OOT COL I treatment demonstrated a booster efficacy in pain, while the questionnaire revealed a reduction in disability. Conclusions: Therefore, this combination therapy might be a promising approach for the management of patients with LBP.

Multi-Alignment method coupled with phylogenetic analysis we disclosed the Nsp9 and Nsp10 non-structural proteins of Corona Virus as rRNA RlmH/K methyltransferases with similarities with bin recombinase and int-core integrase fold. Further, Nsp9 has similarities to S8 ribosomal protein and Nap10 has similarity to S10 ribosomal protein. Previously, we showed Nsp13, Nsp14, Nsp15 and Nsp16 are also different types of rRNA RlmE/N and Cfr-like methyltransferases-ribonuclease with RNA helicase domains. Two domains of Nsp13 astonishingly have similarities to ribosomal proteins L6 and L9. Taken together, Nsp9/10 and Nsp13-16 proteins could mimic host ribosome assembly and also could methylate rRNA of mitobibosome preventing mitochondrial protein synthesis and oxidative phosphorylation. Low ATP synthesis causes lowering blood pressure following coma but very ATP concentration (1-10nM) surely induces platelets aggregation through vWA, collagen and GpIIb/IIIa proteins followed by fibrin formation and blood clotting as recently have seen in the lung of many Corona virus infected patients. We have also postulated that two polyproteins itself resemble like 28S and 38S mitoribosome subunits and compete with rRNAs inhibiting the ribosome turnover and new protein synthesis due to their similarities with many ribosomal proteins. Such finding may be valuable in computer-based novel drug design against Corona virus.

Background: Wideband tympanometry (WBT) has the potential to distinguish various mechanical middle ear and inner ear pathologies noninvasively. This study investigated the diagnostic value of WBT in the diagnosis of enlarged vestibular aqueduct (EVA). Methods: The absorbance and resonance frequency (RF) of patients with EVA (40 ears, 25 patients) and matched population controls (39 ears, 28 subjects) were compared, alongside receiver operating characteristic (ROC) analysis. Correlations between VA width and RF were also examined. Results: Patients with EVA had higher absorbance at low frequencies (226–917 Hz) and lower absorbance at high frequencies (2,520–4,896 Hz) compared to controls. The RF of the EVA group was significantly lower versus controls (751 [391–1,165] vs. 933 [628–1,346] Hz). ROC analysis revealed area under the curve values of 0.771 and 0.801 respectively, for absorbance and RF. RF had a sensitivity, specificity, positive predictive value, and negative predictive value of 74.4%, 82.5%, 76.7%, and 80.6%, respectively, for diagnosing EVA. In the EVA group, the VA midpoint width (r = −0.334) and VA petrous width (r = −0.402) both significantly correlated with RF. Conclusion: Our findings support the utility of WBT for diagnosing EVA, with RF as the optimal index used.

Airborne Frequency Diversity Array (FDA) radar operating at a high pulse repetition frequency encounters severe range-ambiguous clutter. The slight frequency increments introduced by the FDA result in angle and range coupling. Under these conditions, conventional space-time adaptive processing (STAP) often exhibits diminished performance or fails, complicating target detection. This paper proposes a method combining elevation oblique subspace projection with azimuth-Doppler STAP to suppress range-ambiguous clutter. By analyzing the relationship between elevation frequency and range, the proposed method compensates for quadratic range dependence. Through the construction of an elevation oblique subspace projection technique, an elevation adaptive filter is used to separate clutter from ambiguous regions. Residual clutter suppression is achieved through azimuth-Doppler STAP, enhancing target detection performance. Simulation results demonstrate that the proposed method effectively addresses range dependence and ambiguity issues, improving target detection performance in complex airborne FDA radar environments.

This paper presents the development of an analytical model of Microelectromechanical Systems (MEMS) internal vibrating ring gyroscope. The internal ring structure consists of eight semicircular beams that are attached to the externally placed anchors. The research work analyses the vibrating ring gyroscope inplane displacement behavior and the resulting elliptical vibrational modes. The elliptical vibrational modes appear as pairs with the same resonance frequency due to the symmetric structure of the design. The analysis commences by conceptualizing the ring as a geometric structure with a circular shape, possessing specific dimensions such as thickness, height, and radius. We construct a linear model that characterizes the vibrational dynamics of the internal vibrating ring. The analysis develops a comprehensive mathematical formulation for the radial and tangential displacements in local polar coordinates, considering the inextensional displacement of the ring structure. By utilizing the derived motion equations, we highlight the underlying relationships driving the vibrational characteristics of the MEMS vibrating ring gyroscope. These dynamic vibrational relationships are essential in enabling the vibrating ring gyroscope's future utilization in accurate navigation and motion sensing technologies.

Flood frequency analysis at large scales, essential for the development of flood risk maps, is hindered by the uncertainty in outputs of process-based hydrological models and the scarcity of gauge flow data. We develop a Bayesian hierarchical model (BHM) based on the Generalized Extreme Value (GEV) distribution for regional flood frequency analysis at high resolution across North America. Our model leverages annual maximum flow data from ≈20000 gauged stations and a dataset of 130 static catchment-specific covariates to predict extreme flows at all catchments over the continent as well as their associated statistical uncertainty. Additionally, a modification is made to the data layer of the BHM to include daily gauge discharge data when available, which improves the precision of the discharge level estimates. We validated the model using a hold-out approach and found that its predictive power is very good for the GEV distribution location and scale parameters and improveable for the shape parameter, which is notoriously hard to estimate. The resulting discharge return levels yield satisfying agreement when compared with available design peak discharge from various government sources. Assessment of the covariates’ contributions to the model also informs on the most relevant underlying factors influencing flood-inducing peak flows. The key covariates in our model are temperature-related bioindicators, the catchment drainage area and geographical location.

This paper is a brief review of our work on the Planck quantized version of general rela- tivity theory. It demonstrates several straightforward methods to rewrite the same equations that we have already presented in other papers. We also explore a relatively new general relativity-inspired field equation based on the original Newtonian mass, which is very differ- ent from today’s kilogram mass. Additionally, we examine two other field equations based on collision space-time, where both energy and matter can be described simply as space and time. We are thereby fulfilling Einstein’s dream of a theory where energy and mass are not needed, or are just aspects of space and time. If this is extended beyond the 4-dimensional space-time formalism of general relativity theory to a 6-dimensional framework—with 3 space dimensions and 3 time dimensions—this ultimately reveals that they are two sides of the same coin. In reality, it is a three-dimensional space-time theory, where space and time are just two sides of the same coin.

In drilling small holes with diameters of 1 mm or less, minute clogging and twining of chips or adhesion of the workpiece material can become factors in causing breakages of the drill bit; moreover, it can be difficult to identify the machining state. Acoustic emission (AE) sensing is a nondestructive inspection technique that measures the elastic-stress waves that are generated when a material is deformed and fractured. AE sensing permits highly sensitive measurements to be made without changing the rigidity of the experimental system, unlike force sensing of cutting resistance, etc. In the present study, attempts were made to identify the machining state and tool wear, and to predict abnormalities in small-diameter drilling by using the change in the frequency of AE signal waveforms arising from deformation and fracture. It was shown that it is possible to predict the breakage of the drill bit by detecting the high-frequency AE signals caused by adhesion. In addition, a correlation map of the AE frequency spectrum for identifying the machining state in a drilling operation is suggested.

Modern power systems are confronted with a spread concern on the frequency stability issue due to the widespread integration of randomly fluctuating renewable resources. To address the above concern, this work introduces a load frequency control (LFC) scheme based on a hydrogen based energy-storage unit and a parameter tuning strategy for fractional-order proportional-integral-derivative (FOPID) controller. Firstly, a two-area interconnected power system (IPS) model, including thermal, hydro, solar, wind, gas power generator, and hydrogen based energy-storage unit, is established. Then, a FOPID controller is designed for this IPS model, and an improved gradient-based optimizer (IGBO) is developed to adaptively regulate the parameters of the FOPID controllers. Finally, the effectiveness of the offered LFC scheme are tested through load disturbance and renewable energy fluctuations test scenarios, and provides comparison and robustness analysis among different schemes. The test results validated that the offered LFC scheme can effectively suppress the frequency fluctuations of IPS and has excellent robustness.

The Stepped Frequency Waveform (SFW) is commonly employed in radar technology to synthesize wideband signals through the aggregation of narrow-band pulses, thereby achieving high-resolution range profiles without the need to increase the radar's instantaneous bandwidth. However, the inherent large time-bandwidth product of SFW introduces substantial ranging errors and energy dispersion, which significantly hinders its efficacy in detecting high-speed objects. This paper introduces a pioneering velocity estimation technique utilizing the fractional Fourier transform (FrFT) to address these limitations. Leveraging the characteristic of the Doppler signal from a moving target, which manifests as a chirp signal with a rate proportional to the target's velocity, the FrFT is utilized for precise velocity estimation. Subsequent to this, velocity compensation is applied using the deduced metrics, followed by the application of the inverse fast Fourier transform (iFFT) to pinpoint the target's exact location. To optimize the computational efficiency of determining the FrFT's optimal order, we propose an iterative algorithm founded on the golden section search method. The effectiveness of the proposed approach is verified by simulation data, and the results demonstrate that the proposed approach can accurately estimate the velocity and the range of the high-speed targets with a relatively low computational complexity.

To investigate the variation patterns of spectral characteristics of main branches in fruit trees due to uneven distribution of growth, pruning, and fruit quality, as well as to determine the optimal fruit vi-bration harvesting, a vibration differential model of tree branches was constructed using the concen-trated mass method. A three-dimensional model of the fruit tree was built using finite element software. The spectral characteristics of each branch were obtained using the linear sweep frequency method. The method of changing the mass of each branch was employed to simulate the variation in branch mass. The frequency of occurrence, mean acceleration, and coefficient of variation of the inherent frequencies were used as evaluation indicators. The results revealed that when the vibration frequency of the fruit tree was at the peak frequency in the tree trunk spectrum, the frequency of occurrence and mean accel-eration were optimal. And the coefficient of variation of branch acceleration was less than 1, indicating a moderate dispersion. Additionally, reducing the branch mass resulted in an increase in the peak fre-quency of the tree trunk spectrum. Therefore, the growth, pruning, and uneven distribution of the branches in fruit trees can alter the spectral characteristics. When harvesting fruit by vibration, selecting the peak frequency in the trunk vibration spectrum as the excitation force frequency yields the best fruit detachment.

This paper describes developing and analyzing an analytical model of Microelectromechanical Systems (MEMS) internal vibrating ring gyroscope. The internal ring structure consists of eight semicircular beams attached to the externally placed anchors. The paper analyses the vibrating ring gyroscope inplane displacement behavior and the resulting elliptical vibrational modes. The elliptical vibrational modes appear as pairs with the same resonance frequency due to the symmetric nature of the design. The analysis commences by conceptualizing the ring as a geometric structure with a circular shape, possessing specific dimensions such as thickness, height, and radius. We construct a linear model that characterizes the vibrational dynamics of the internal vibrating ring. The analysis encompasses comprehensive mathematical formulations for the radial and tangential displacements in local polar coordinates, considering the inextensional displacement of the ring structure. By utilizing the derived equations, we highlight the underlying relationships driving the vibrational characteristics of the MEMS vibrating ring gyroscope. These dynamic vibrational relationships are essential in enabling the vibrating ring gyroscope's future utilization in accurate navigation and motion sensing technologies.

The E-learning system has achieved great development after the pandemic. In this work, we proposed three artificial intelligence-based enhancements to our linguistic interactive E-learning system from different aspects. Compared with the original phonetic transcription exam system, our enhancements include an MFCC+CNN-based disordered speech classification module, a Transformer-based Grapheme-to-Phoneme converter, and a Tacotron2-based IPA-to-Speech speech synthesis system. This work not only provides a better experience for the users of this system but also explores the utilization of artificial intelligence technologies in the E-learning field and linguistic field.

The generalized dynamic model of the rotor system, presented in the paper, is the first model that takes into account the interconnected oscillations of the “rotor - weakly conductive fluid – foundation” system under the action of such parameters as fluid and rotor motion, linear eccentricity, friction forces, foundation vibration and nonlinear characteristics of rolling bearings, as well as the action of a magnetic field on the fluid. Consistent equations of motion for the system “rotor - weakly conductive fluid – foundation” were derived and solved analytically. Forced and natural oscillations of the system were analyzed, and the distinctive features of the rotor system dynamics were revealed. The values of frequencies and amplitudes, which are one of the main factors determining the dynamic behavior of the system, were obtained and studied.

Artworks play a fundamental role in the cultural and economic asset of communities, enforcing their identity and helping the social integration. Despite their importance, they are not always adequately protected against degradation, which can be induced by the aging, atmospheric and human-induced occurrence, and catastrophic events. Earthquakes certainly represent one of the main risks for art goods; however, traffic, construction works, and shipment can also represent a threat for art goods. Therefore, the assessment of the vulnerability of art collection to dynamic excitations plays a crucial role in their conservation, and it has been collecting an increasing attention by researchers, academics, and Museums’ managers. This work focuses on the vulnerability of the art collections exhibited at the Museum “Gaio Cilnio Mecenate” in Arezzo. Namely, it aims at assessing the effective dynamic loading experienced by the artworks, which is a function of the dynamic propagation plaid by the foundation soil, by the building and by the displayers used for exhibition. In this study the dynamic properties of some of the displayers used for exhibiting the art collections are investigated by performing an experimental survey. The analysis of the experimental data lead to assess the proper frequencies of the displayers, which have been compared to the ones of the building and the foundation soil of the Museum.

Detecting, especially locating local degradations at an incipient stage, is very important for mission-critical high voltage rotating machines. One particular challenge of the existing testing techniques is that the characteristic of a local incipient defect is not prominent due to various factors such as averaging with the healthy remainder, attenuation in signal propagation, interference, and varied operating conditions. This paper proposes and investigates the frequency domain reflectometry (FDR) technique based on scattering parameter measurement. The FDR result presents the object length, wave impedance, and reflections due to impedance discontinuity along the measured windings. Experiments were performed on two commercial coils with artificially made defects. These defects include turn-to-turn short, surface creepage, loose coils, and local overheating, which are commonly seen in practice. Two practical water pumps in the field were also selected for investigation. The study outcome shows that the FDR can identify and locate both structure and insulation degradations of both shielded and unshielded objects with good sensitivity. This makes the FDR a comprehensive tool for fault diagnosis and aging assessment.

Initially introduced almost thirty years ago for the express purpose of providing electronic warfare systems the capabilities to detect, characterize, and identify radar emitters, Specific Emitter Identification (SEI) has recently received a lot of attention within the research community as a physical layer technique for securing Internet of Things (IoT) deployments. This attention is due in large part to SEI’s demonstrated success in passively and uniquely identifying wireless emitters using traditional machine learning and the success of Deep Learning (DL) within the natural language processing and computer vision areas. SEI exploits distinct and unintentional features present within an emitter’s transmitted signals. The existence of these distinctive and unintentional features is attributed to slight manufacturing and assembly variations that exist within and between the components, sub-systems, and systems that comprise an emitter’s Radio Frequency (RF) front end. Although sufficient to facilitate SEI, these features do not hinder normal operations such as detection, channel estimation, timing, and demodulation. However, despite the plethora of SEI publications, it has remained largely a focus of academic endeavors that primarily focus on proof-of-concept demonstration and little to no use in operational networks for various reasons. The focus of this survey is a review of SEI publications from the perspective of its use as a practical, effective, and usable IoT security mechanism, thus we use IoT requirements and constraints (e.g., wireless standard, nature of their deployment) as a lens through which each reviewed paper is analyzed. Previous surveys have not taken such an approach and have only used IoT as motivation, a setting, or a context. In this survey, we consider operating conditions, SEI threats, SEI at scale, publicly available data sets, and SEI considerations that are dictated by the fact that it is to be employed by IoT devices or IoT infrastructure.

Transition delaying is of great importance for the drag and heat flux reduction of hypersonic flight vehicles. The first mode within low frequency and the second mode within high frequency exist simultaneously during the transition of hypersonic boundary layer. This paper proposes a novel bi-frequency synthetic jet to suppress low- and high-frequency disturbances at the same time. Orthogonal table and variance analysis are used to compare the control effects of jet with different frequencies, amplitudes and positions. Linear stability analysis results show that, low frequency synthetic jet can suppress the first mode when it is arranged upstream of synchronization point, while the second mode control effect is relatively weak. The higher the high frequency is, the stronger the suppression effect is on the first mode. For the second mode, the suppression effect is only at f2=89.09kHz. The larger the amplitude, the weaker the promoting effect for the first mode and the second mode, and the more obvious the suppressing effect. For the cases with synthetic jet downstream of synchronization point, all levels of the three parameters promote the unstable mode. In terms of the growth rate with the spanwise wave number, the control effect of the same factor and level under different spanwise wave number is different. In order to obtain the optimal control effect on transition, the three factors and the arrangement position of the synthetic jet should be selected as follows: the position is arranged in the upstream, with f1 = 17.82kHz, f2 = 89.9kHz, a =0.007, so that the maximum growth rate of the first mode is reduced by 9.06% and that of the second mode is reduced by 1.28% compared with the uncontrolled state.

In this paper, four types of open service signals of BDS-3 satellite (B1I, B1C, B2a, and B3I) and B2I signals broadcasted by BDS-2 satellites were used in the time frequency transfer and positioning experiments with signal coexisting in BDS system, and the single frequency PPP (precise point positioning) method was used. Modified GRoup And PHase Ionospheric Correction (GRAPHIC) method was proposed and verified by the experiment. The results show that 18 selected stations can achieve decimeter-level positioning results with single frequency. Compared with the general observation method, the proposed modified GRAPHIC method improves the stability and precision of positioning and timing significantly, and the positioning accuracy of 5 frequency signals is increased 40.4%, 32.2%, 80.3%, 12.4%, and 10.3%, respectively. The frequency stability can reach the same accuracy as that of dual-frequency with BDS in the current state.

After proposing a natural metric for the space in which particles spin which implements the principle of maximum frequency, E=hf is generalised and its inverse Fourier transform is calculated. As a necessary result, a metric is found for the space in which quantum particles spin, hence the possibility of explanation of correlation of spacelike-separated particles is opened up.

A microwave-photonics method has been developed for measuring distributed acoustic signals. This method uses microwave-modulated low coherence light as a probe to interrogate distributed in-fiber interferometers, which are used to measure acoustic-induced strain. By sweeping the microwave frequency at a constant rate, the acoustic signals are encoded into the complex microwave spectrum. The microwave spectrum is transformed into the joint time-frequency domain and further processed to obtain the distributed acoustic signals. The method is first evaluated using an intrinsic Fabry Perot interferometer (IFPI). Acoustic signals of frequency up to 15.6 kHz were detected. The method was further demonstrated using an array of in-fiber weak reflectors and an external Michelson interferometer. Two piezo-ceramic cylinders (PCCs) driven at frequencies of 1700 Hz and 3430 Hz were used as acoustic sources. The experiment results show that the sensing system can locate multiple acoustic sources. The system resolves 20 nε when the spatial resolution is 5 cm. The recovered acoustic signals match the excitation signals in frequency, amplitude, and phase, indicating an excellent potential for distributed acoustic sensing (DAS).

Background: Most prevalence surveys on nocturia have focused on older populations. This study aimed to measure the nocturia prevalence across the full spectrum of male adults living in Hong Kong, where severity and associated quality-of-life (QoL) were also explored. Methods: A cross-sectional population-based survey was conducted in men aged 18 or above using the ICIQ-NQoL Questionnaire. Results: With 1,239 respondents at age ranged 18-99, the overall nocturia prevalence were found to be 63.0% (ranged 41.6-84.6% at different age groups) and 31.2% (ranged 13.0-56.3% at different age groups), for ≥1 and ≥2 bedtime voiding episodes, respectively. The chance of nocturia was dramatically increased at age 60 or above while both prevalence and voiding frequency were increased with advancing age. About 83% of the nocturia men experienced 1-2 voiding episodes per night, but many of them had self-rated their QoL poor or very poor and indicated moderate-to-high bothersome. Younger men at age 18-39 were found to have high prevalence as 41.6% and almost 30% of them rated poor or very poor QoL. Conclusions: Nocturia was not only affecting the older populations but also caused significant bothersome and negative impacts on QoL in younger males.

This article examines the impact of some system parameters on an industrial system composed of two dissimilar parallel units with one repairman. The active unit may fail due to essential factors like aging or deteriorating, or exterior phenomena such as Poisson shocks that occur at various time periods. Whenever the value of a shock is larger than the specified threshold of the active unit, the active unit will fail. The article assumes that the repairman has the right to take any of two decisions at the beginning of the system operation: either a takes a vacation if the two units work in a normal way, or stay in the system to monitor the system until the first system failure. In case of having a failure in any of the two units during the absence of the repairman, the failing unit will have to wait until the repairman is called back to work. We suppose that the value of every shock is assumed to be i.i.d. with some known distribution. The length of the repairman’s vacation, repair time, and recall time are arbitrary distributions. Various reliability measures have been calculated by the supplementary variable technique and the Markov’s vector process theory. At last, numerical computation and graphical analysis have been given for a particular case to validate the derived indices.

Defect detection in ferromagnetic substrates is often hampered by non-magnetic coating thickness variation when using conventional eddy current testing technique. The lift-off distance between the sample and the sensor is one of the main obstacles for the thickness measurement of non-magnetic coatings on ferromagnetic substrates when using the eddy current testing technique. Based on the eddy current thin-skin effect and the lift-off insensitive inductance (LII), a simplified iterative algorithm is proposed for reducing the lift-off variation effect using a multi-frequency sensor. Compared to the previous techniques on compensating the lift-off error (e.g., the lift-off point of intersection) while retrieving the thickness, the simplified inductance algorithms avoid the computation burden of integration, which are used as embedded algorithms for the online retrieval of lift-offs via each frequency channel. The LII is determined by the dimension and geometry of the sensor, thus eliminating the need for empirical calibration. The method is validated by means of experimental measurements of the inductance of coatings with different materials and thicknesses on ferrous substrates (dual-phase alloy). The error of the calculated coating thickness has been controlled to within 3 % for an extended lift-off range of up to 10 mm.

Maxwell equation for the electric field has been solved for any medium by suggesting the wavenumber and angular frequency be complex quantities. This accounts for the field decay by interaction with the medium.This expression for the time and special decay of the electric field in a medium is used to construct a new wave function sensitive to the medium physical properties. This new wave function, unlike the conventional one, differentiates between a beam of particles in a vacuum and that enters a medium which is an attenuated due to the scattering effect.Another expression for time decaying electric field was obtained using Newton’s laws for frictional medium. This expression shows that the electric field diminishes due to friction.Fortunately, this time decaying part of the electric field is typical to that derived from Maxwell’s equations. Finally, a new Schrodinger equation sensitive to the medium properties was derived. This equation, fortunately, describes some scattering processes for Protein scattering, scattering of x-rays, opto-acoustic phonons, and Raman scattering for some materials successfully .

This paper presents findings of a study on continuous feed-in management and continuous synthetic inertia contribution with wind turbines. A realistic case study, based on real measurements, is outlined. A wind turbine feeds into a weak feeder, such that its power has to be adapted to the permissible loading of this feeder. At the same time the wind turbine is to provide inertia to the grid by applying the previously published variable inertia constant controller. It is discussed that optimal grid utilisation and simultaneous inertia contribution are mandatory for the frequency control in power systems that are heavily penetrated with renewable energies. The study shows that continuous feed-in management can be combined well with continuous inertia provision. There are hardly any negative consequences for the wind turbine. The benefits for the grid are convincing, both in terms of increased system utilisation and in terms of provided inertia. It is concluded that wind turbines can enhance angular stability in a power system to a larger extent than conventional power plants.

Low-frequency electron paramagnetic resonance (EPR) is used to extract the EPR parameter A-mid and support the approximate X-band value of g-mid for Ba(Co_yZn_1/3-yTa_2/3)O₃. Although cobalt hyperfine structure for the [+/−1/2> state is often unresolved at X-band or S-band, it is resolved in measurements on this compound. This allows for detailed analysis of the molecular orbital for the [+/−1/2> state, which is often the ground state. Moreover, this work shows that the EPR parameters for Co substituted into Zn compounds gives important insight into the properties of zinc binding sites.

Effective discharge, which represents the flow, or range of flows, that transport the most sediment over long term, was determined based on the mean daily flow discharge and mean daily suspended sediment discharge recorded between 1994 and 2014 at four gauging stations along the Trotuș River. This study proposes an efficient method for the estimation of effective discharge based on observed values of the suspended sediment load. By employing this method the suspended sediment load is no longer either under- or overestimated as in the cases when the assessment is based on sediment rating curves. The assessment on effective discharge was performed at two distinct levels: for the entire data series during the investigated time spans and, subsequently, for flows less than the bankfull discharge. The effectiveness curves of the suspended sediment transport characteristics revealed highly multimodal characteristics with many peaks, indicating ample ranges for the effective discharges. The main effective discharge corresponded to large flood events, which are typical for the upper end of the discharge range, whereas the secondary effective discharges corresponded to sub-bankfull flows, which are more frequent. The changes that occurred in the channel bed are reflected by the temporal variations in the effective discharge.

This paper aims to study the surface homogenization and integrity of Ti-6Al-4V alloy by longitudinal-torsional coupled ultrasonic vibration assisted ball-end milling. A method of continuous processing between the flat surface and freeform surface connection is proposed by using ultrasonic vibration assisted ball-end precision milling, during this process, it is not necessary to exchange the cutting tool. The way has been explored for changing the homogenization of surface on Ti-6Al-4V by ultrasonic vibration-assisted milling (UVAM). Cutting experiments employing three parameters, cutting speed, feed rate and depth of cut and two types of machining forms using ball-end milling with UVAM and conventional milling (CM) respectively. The high frequency cutting force, finished surface roughness, topography and residual stresses on the surface and tool wear have been measured by advanced instruments. Particularly, adopting the high frequency cutting force measurement system, it is concluded cutting force in ball-end milling decreased significantly using UVAM as against CM. Moreover, the surface roughness by UVAM with ball-end milling is much better than the CM at a high cutting speed. However, an opposite trend is observed at a low cutting speed. Especially, there is a steep decrease from Ra 0.828 μm average value at 4000 rpm to Ra 0.129 μm average value at 5000 rpm. At the same time, the homogenization of surface roughness and residual stresses decrease significantly in UVAM as compared to which in CM when taking the transversal-longitudinal ratio into consideration. Cutting experiments and measuring results are demonstrated the validity and feasibility of UVAM with ball-end milling, and this method enjoys significant advantages compared to CM process.

Vibration measurement serves as the basis for various engineering practices such as natural frequency or resonant frequency estimation. As image acquisition devices become cheaper and faster, vibration measurement and frequency estimation through image sequence analysis continue to receive increasing attention. In the conventional photogrammetry and optical methods of frequency measurement, vibration signals are first extracted before implementing the vibration frequency analysis algorithm. In this work, we demonstrated that frequency prediction can be achieved using a single feed-forward convolutional neural network. The proposed method is verified using a vibration signal generator and excitation system, and the result obtained was compared with that of an industrial contact vibrometer in a real application. Our experimental results demonstrate that the proposed method can achieve acceptable prediction accuracy even in unfavorable field conditions.

Star block-copolymers (SBCs) are macromolecules formed by a number of diblock copolymers anchored to a common central core, being the internal monomers solvophilic and the end monomers solvophobic. Recent studies have demonstrated that SBCs constitute a self-assembling building blocks with specific softness, functionalization, shape, and flexibility. Depending on different physical and chemical parameters the SBCs can behave as flexible patchy particles. In this paper, we study the rotational dynamics of isolated SBCs using a hybrid mesoscale simulation technique. We compare three different approaches to analyse the dynamics: the laboratory frame, the non-inertial Eckart's frame, and a geometrical approximation relating the conformation of the SBC to the velocity profile of the solvent. We find that the geometrical approach is adequate when dealing with very soft systems while in the opposite extreme, the dynamics is best explained using the laboratory frame. On the other hand, the Eckart frame is found to be very general and to reproduced well both extreme cases. We also compare the rotational frequency and the kinetic energy with the definitions of the angular momentum and inertia tensor different from recent publications.

This paper attempts at applying adaptive network-based fuzzy inference system (ANFIS) for analysis of the resonant frequency of a microstrip rectangular patch antenna with two equal size slots which are placed on the patch vertically. The resonant frequency is calculated as the position of slots is shifted to the right and left sides on the patch. As a result , the antenna resonates at more than one frequency . Commonly, machine algorithms based on artificial neural networks are employed to recognize the whole resonant frequencies. However ,they fail to estimate the resonant frequencies correctly as in some cases variations are not very sensible and the resonant frequencies overlap each other . It can be concluded that artificial neural networks could be replaced in such designs by the adaptive network-based fuzzy Inference system due to its high approximation capability and much faster convergence rate.

The mitigation of NLOS (non-line-of-sight) propagation conditions is one of main challenges in wireless signals based indoor localization. When RFID localization technology is applied in applications, RSS fluctuates frequently due to the shade and multipath effect of RF signal, which could result in localization inaccuracy. In particularly, when tags carriers are walking in LOS (line-of-sight) and NLOS hybrid environment, great attenuation of RSS will happen, which would result in great location deviation. The paper proposes an IMU-assisted (Inertial Measurement Unit) RFID based indoor localization in LOS/NLOS hybrid environment. The proposed method includes three improvements over previous RSS based positioning methods: IMU aided RSS filtering, IMU aided LOS/NLOS distinguishing and IMU aided LOS/NLOS environment switching. Also, CRLB (Cramér-Rao Low Bound) is calculated to prove theoretically that indoor positioning accuracy for proposed method in LOS/NLOS mixed environment is higher than position precision of only use RSS information. Simulation and experiments are conducted to show that proposed method can reduce the mean positioning error to around 3 meters without site survey.

The COVID-19 pandemic and the Movement Control Order (MCO) have had a negative impact on the financial well-being of low-income families in urban areas. The study involved respondents living in the Public Housing Project (PPR) residential areas in Kuala Lumpur – the capital of Malaysia. The key finding is the financial well-being of low-income urban families was negatively impacted due to the COVID-19 pandemic and the MCO implementation. Furthermore, the impact on the financial well-being of low-income urban families is significantly difference in terms of types of family, type &amp; sectoral employment, type of home ownership, household monthly income and education level. Reforms to the financial assistance system and community empowerment of low-income urban families are necessary to increase the community's preparedness and resilience in the face of new shocks in the future.

Background: Bone metastases (BM) have a detrimental effect on survival for patients with solid cancers. Materials and methods: This systematic review respected the Preferred Reporting Items for Systematic Reviews and Meta-Analysis (PRISMA) guidelines. Results: When investigating OP as a risk factor for BM development, for breast cancer patients, some articles do not differentiate between intrinsic breast cancer subtypes. BMD does not seem to contribute in a significant manner when investigating Luminal A breast cancer. While researching breast cancer regardless of intrinsic subtype, untreated OP increases the risk of bone metastasis when compared to no OP group or treated OP group. In urological cancer cases, OP seems to predispose the patients to BM, especially early after diagnosis. Investigating risk factors for OP development in cancer patients resulted in the identification of 32 articles. Most articles identified risk factors for osteoporosis development in the context of breast cancer patients. Other commonly investigated solid cancers were prostate, other urological cancers, gynecological malignancies, and other less common subtypes of solid tumors. Discussion: While investigating OP as a risk factor for BM, it becomes clear that there is a high grade of heterogeneity in the behavior of each type of cancer in its dynamic concerning bone metastasis, and thus, OP might have different behaviors as a risk factor depending on the situation. Conclusion: There is a need for data regarding cancer subtypes that have not been explored concerning their interaction with the skeletal system in a low bone mineral density scenario.

Thermoplastic fiberglass has been compression molded in the shape of thick panels with the nominal thickness of 10 mm and the size of 300x300 mm2. A simplified procedure has been adopted to speed up the lamination procedure, and making it adapt to the aim of recycling waste glass fiber fabrics and thermoplastics films. Low density polyethylene has been used as matrix to simplify the laboratory activities, but the same procedure can be extended to any other thermoplastic film, such as polyamide. The final thermoplastic composite shows unique properties in terms of repairability and improves its performances by increasing the number of repairing steps. For this aim, a repairability test has been designed in the bending configuration, and 3 consecutive cycles of bending/repairing/bending have been carried out. Static mechanical properties were, instead, low in comparison with traditional fiberglass, because of the choice of a polyethylene matrix. Bending tests have shown that the maximum strength is lower than 10 MPa and the elastic modulus less than 1 GPa. Nevertheless, the toughness of the thermoplastic composite was very high, and the samples continued to deform under bending for any displacement.

Introduction: Low back pain (LBP) is the leading cause of lost productivity, absenteeism, disability, and early retirement worldwide. LBP treatment should be comprehensive, including prevention, education, diagnosis, and various treatment methods. Treatment can be divided into pharmacological and non-pharmacological. The role of physiotherapy in the comprehensive treatment of LBP is very important. Elastic therapeutic tape, also called kinesiology tape or therapeutic kinesiology tape, has been used for about 50 years. Purpose: The aim of this study was to evaluate the effectiveness of Kinesio taping in patients suffering from (LBP) and its possible effect on the swing of the center of pressure (COP), balance, gait, improvement of coordination, and pain reduction. Material and methods: A total of 60 patients aged 20 to 83 years (54% women) were examined, all of whom met the inclusion and exclusion criteria. In the experimental group, in addition to comprehensive rehabilitation, kinesiotaping of the L1-L5 spine was used. The control group underwent balance control training. The research tools used included the Bohannon single-leg standing test, the FAC scale - Functional Ambulatory Category, the Podsiadlo and Richardson Standing and Walking Test - Timed Up and Go (TUG), lumbar spine mobility assessment, Lasegue's sign and examination of neurological deficit symptoms. and self-assessment of pain using the Visual Analogue Scale (VAS). Results: Kinesio taping has a statistically significant effect on postural control, balance, gait, coordination, and pain. The main parameter with a statistically significant effect on the effects of Kinesio taping was age (below 55 years), which was also observed in the control group. Conclusions: Kinesio taping is an effective method in the treatment of LBP. It improves postural control, balance, gait, coordination, and pain.

Our previous study demonstrated that the acute high-dose rate (3.3 Gy/minute) gamma irradiation of postnatal day 3 (P3) mice with 5Gy induced depression and drastic neuropathological changes in the dentate gyrus of the hippocampus of the adult mice. The present study investigated the effects of chronic low-dose-rate (1.2mGy/h) gamma irradiation from P30 to P180 with a cumulative dose of 5Gy on animal behaviour, hippocampal cellular change, miRNA and mRNA expression in the hippocampus and blood in female mice. The radiation exposure did not significantly affect the animal's body weight and neuropsychiatric changes such as anxiety and depression examined by neurobehavioural tests including open field, light-dark box, elevated plus maze, tail suspension test and forced swim test. Immunohistochemical staining did not detect any obvious loss of mature and immature neurons (NeuN and DCX) or any inflammatory glial response (IBA1, GFAP, and PDGFR1). Nevertheless, r-H2AX foci in the stratum granulosum of the dentate gyrus were significantly increased, suggesting the chronic low dose rate irradiation induced persistent DNA damage foci in mice. miRNA sequencing and qRT-PCR indicated an increased expression of miR-448-3p and miR-361-5p, but decreased expression of miR-193a-3p in the mouse hippocampus. Meanwhile, mRNA sequencing and qRT-PCR showed a reduced expression of Ccn1, Fli1, Fosb, Ets1, Hs3st5, and Eif4ebp1, but enhanced expression of Cort, Foxh1, and Opalin. Database searching by miRDB and TargetScan predicted that FLI1 and HS3ST5 are the targets of miR-448-3p, and Eif4ebp2 is the target of miR-361-5p. miRNA/mRNA sequencing and qRT-PCR results in blood showed the increased expression of miR-6967-3p and the decreased expression of its target S1pr5. The interactions of these miRNAs and mRNAs may contribute to the chronic low dose rate radiation-induced persistent DNA damage.

This study aims to evaluate the effectiveness of inactivating Salmonella enteritidis in fresh chicken breast by irradiation using a combination of short-wave UV (0, 3, 6, 9, 12 and 15 J / cm2) and a natural antimicrobial such as caffeine (0, 5, 10, 15 and 20 nM/g) as alternative proposals to conventional techniques to reduce pathogens in food. The temperatures used were from 2 to 22°C. The most suitable models were double Weibull in 60% of cases with an adjustment of R2 0.9903-0.9553 and Weibull + cola, in 46.67%, with an adjustment of R2 of 0.9998-0.9981. Noting that the most effective combination in the reduction of Salmonella was 12 J/cm2 of UV light and 15 nM/g of caffeine, with a reduction of 6 CFU/g and an inactivation rate of 0.72. The synergistic effect was observed by increasing caffeine and UV light. Furthermore, the physic-chemical characteristics of the food matrix were not affected by the combination of both technologies. Therefore, these results suggest that this combination can be used in the food industry to effectively inactivate Salmonella enteritidis, without deteriorating product quality.

Low back pain (LBP) is one of the most common musculoskeletal conditions, resulting in continuous pain and disability. However, reliable evidence exists for only a few existing therapies for LBP. This study aimed to determine the efficacy of a newly designed cutting-edge massage device that uses a mechanical sequential ascending method. Fifteen individuals with LBP underwent mechanical sequential ascending massage method with thermal therapy (AM-TH), thermal therapy (TH), rotating roller massage method with thermal therapy (RM-TH), and clinical assessments. We analysed the participants’ biomechanical muscle properties, pain, satisfaction, and disability measured immediately before and after treatment. There was a significant decline in tone and stiffness in the upper and lower regions of the paraspinal muscles when AM-TH was administered on three or more occasions (p &lt; 0.05). AM-TH was more effective than RM-TH in reducing pain, with a significant reduction in pain over time (p &lt; 0.05). Participants were most satisfied with RM-TH; over time, RM-TH was effective in improving participants’ disabilities (p &lt; 0.05). AM-TH has been demonstrated to be effective in individuals with LBP, improving muscle tone and stiffness and reducing pain. Therefore, it may be a useful treatment for LBP.