Lithium-ion batteries with improved energy densities have made understanding the Solid Electrolyte Interphase (SEI) generation mechanisms that cause mechanical, thermal, and chemical failures more complicated. SEI processes reduce battery capacity and power. Thus, a review of this area's understanding is important. It is essential to know how batteries degrade in EVs to estimate battery lifespan as it goes, predict, and minimize losses, and determine the ideal time for a replacement. Lithium-ion batteries used in EVs mainly suffer two types of degradation: calendar degradation and cycling degradation. Despite the existence of several existing works in the literature, several aspects of battery degradation remain unclear or have not been analyzed in detail. This work presents a systematic review of existing works in the literature. The results of the present investigation provide insight into the complex relationships among various factors affecting battery degradation mechanisms. Specifically, this systematic review examined the effects of time, side reactions, temperature fluctuations, high charge/discharge rates, depth of discharge, mechanical stress, thermal stress, and the voltage relationship on battery performance and longevity. The results revealed that these factors interact in complex ways to influence the degradation mechanisms of batteries. For example, high charge currents and deep discharges were found to accelerate degradation, while low temperatures and moderate discharge depths were shown to be beneficial for battery longevity. Additionally, the results showed that the relationship between cell voltage and State-of-Charge (SOC) plays a critical role in determining the rate of degradation. Overall, these findings have important implications for the design and operation of battery systems, as they highlight the need to carefully manage a range of factors to maximize battery performance and longevity. The result is an analysis of the main articles published in this field in recent years. This work aims to present new knowledge about fault detection, diagnosis, and management of lithium-ion batteries based on battery degradation concepts. The new knowledge is presented and discussed in a structured and comprehensive way.

China’s leading development of a complete battery value chain for Electric Vehicles (EV) is restructuring the global automotive sector. The competitive advantage of China's EV battery industry lies on its firms’ core competency and political economic geography. Based on first-hand empirical material and data obtained from years of fieldwork in an EV battery cluster in South China, this paper identifies what the Chinese EV battery industry’s core competency is and details how it is built up from below. The current core competency of Chinese battery firms is their mass manufacturing capability to supply lithium-ion batteries vehicle manufacturers (OEMs) with stable and consistent quality as well as competitive prices. This competency is acquired by firms through technological learning at workshop level while taking use of their experiences accumulated in mass production of batteries for consumer electronics sectors. Furthermore, the rapid learning and accumulation of knowledge on battery manufacturing at large scale is also facilitated by the industrial cluster environment where firms are embedded. Supported and promoted by local government policies, Chinese EV battery clusters are composed of firms from different segments of a complete battery value chain. The findings illuminate the likely strategic strengths, weaknesses, and futures of the Chinese EV battery industry in global competition.

Estimation of core and surface temperature is one of the crucial functionalities of the lithium-ion Battery Management System (BMS) towards providing effective thermal management, fault detection and operational safety. While, it is impractical to measure core temperature using physical sensors, implementing a complex estimation strategy in on-board low-cost BMS is challenging due to high computational cost and the cost of implementation. Typically, a temperature estimation scheme consists of a heat generation model and a heat transfer model. Several researchers have already proposed ranges of thermal models having different levels of accuracy and complexity. Broadly, there are first-order and second-order heat capacitor-resistor-based thermal models of lithium-ion batteries (LIBs) for core and surface temperature estimation. This paper deals with a detailed comparative study between these two models using extensive laboratory test data and simulation study to access suitability in online prediction and onboard BMS. The aim is to guide whether it’s worth investing towards developing a second-order model instead of a first-order model with respect to prediction accuracy considering modelling complexity, experiments required and the computational cost. Both the thermal models along with the parameter estimation scheme are modelled and simulated using MATLAB/Simulink environment. Models are validated using laboratory test data of a cylindrical 18650 LIB cell. Further, a Kalman Filter with appropriate process and measurement noise levels are used to estimate the core temperature in terms of measured surface and ambient temperatures. Results from the first-order model and second-order models are analyzed for comparison purposes.

This paper investigates the polarization and heat generation characteristics of batteries under different ambient temperatures and discharge rates by means of using a coupled electric-thermal model. The study found that the largest percentage of polarization is ohmic polarization, followed by concentration polarization and electrochemical polarization. The values of the three types of polarization are generally small and stable under normal-temperature environments and low-discharge rates. However, they increase significantly in low-temperature environments and high-discharge rates and continue to rise during the discharge process. Additionally, ohmic heat generation and polarization generation also increase significantly under these conditions. Reversible entropy heat is less sensitive to ambient temperature but increases significantly with the increase of the discharge rate. Ohmic heat generation and polarization heat generation contribute to the total heat generation of the battery at any ambient temperature, while reversible entropy heat only contributes to the total heat generation of the battery at the end of discharge.

This paper presents an optimized energy management strategy for Li-ion power batteries used on electric vehicles (EVs) at low temperatures. Under low-temperature environments, EVs suffer a sharp driving range loss resulted from the energy and power capability reduction of the battery. Simultaneously, because of Li plating, battery degradation becomes an increasing concern as temperature drops. All these factors could greatly increase the total vehicle operation cost. Prior to battery charging and vehicle operating, preheating battery to a battery-friendly temperature is an approach to promote energy utilization and reduce total cost. Based on the proposed LiFePO4 battery model, the total vehicle operation cost under certain driving cycles is quantified in the present paper. Then given a certain ambient temperature, a target temperature of preheating is optimized under the principle of minimizing total cost. As for the preheating method, a liquid heating system is also implemented on an electric bus. Simulation results show that the preheating process becomes increasingly necessary with a decreasing ambient temperature; however, the preheating demand declines as driving range grows. Vehicle tests verify that the preheating management strategy proposed in this paper is able to save total vehicle operation cost.

Electric vehicles (EV) are getting more commonplace in the transportation sector in recent times. As the present trend suggests, this mode of transport is likely to replace the internal combustion engine (ICE) vehicles in near future. Each of the main EV components has a number of technologies that are currently in use or can become prominent in the future. EVs can cause significant impacts on the environment, power system, and other related sectors. The present power system can face huge instabilities with enough EV penetration; but with proper management and coordination, EVs can be turned into a major contributor to the successful implementation of smart grid. There are possibilities of immense environmental benefits as well, as the EVs can extensively reduce the greenhouse gas emission from the transportation sector. However, there are some major obstacles for EVs to overcome before replacing the ICE vehicles totally. This paper is focused on reviewing all the useful data available on EV configurations, energy sources, motors, charging techniques, optimization techniques, impacts, trends, and possible directions of future developments. Its objective is to provide an overall picture of the current EV technology and ways of future development to assist in future researches in this sector.

A modular approach to the construction of electric machines, drive systems, power supply systems is a new direction of modern technology development. Especially, the modular approach is promising for electric vehicles due to such positive aspects as increased efficiency, fault tolerance, overall reliability, safety, enhanced control capabilities, etc. In this work, the modular approach is comprehensively applied to an EV powertrain system, which includes a dual three-phase (DTP) BLDC motor with two machine modules of an asymmetric configuration, two battery modules and a supercapacitor module (SCM). The proposed H–H configuration of modular EV powertrain system includes four voltage source inverters that combine the power modules with the open ends of the windings (OEW) of the module machine armature, and provide control of their operation. Based on the developed mode system of the OEW machine module operation for EV traction and braking, a general control algorithm for the proposed configuration of the modular EV powertrain system has been developed. It combines the control of the operating modes with the functions of maintaining the required SOC level of the SCM and equalizing the SOCs of the two battery modules. The conducted simulation and experimental studies confirmed the workability and effectiveness of the proposed solutions.

Driven by the rapid uptake of battery electric vehicles, Li-ion power batteries are increasingly reused in stationary energy storage systems, and eventually recycled to recover all the valued components. Offering an updated global perspective, this study provides a circular economy insight on lithium-ion battery reuse and recycling.

This paper proposes an electric vehicle routing problem with considering states of charging stations and suggests solution strategies. Charging of electric vehicles is a main issue in the field of electric vehicle routing problem. There are many studies to find locations of charging stations, recharging functions for batteries of vehicles, and so on. However, states of charging stations significantly affect the routes of electric vehicles, which is not much explored. The states may include open or close of charging stations, occupied or empty of charging slots, and so on. This paper investigates how the states of charging stations are estimated and routing strategies are determined. We formulate a mixed integer programming model and suggest how to solve the problem with exact method. Numerical examples provide the optimal routing strategies of electric vehicles in the changing environments of the states of charging stations.

The development of accurate dynamic battery pack models for electric vehicles (EVs) is critical for the ongoing electrification of the global automotive vehicle fleet, since these serve as a key element in the energy performance of an EV powertrain system. The Equivalent Circuit Model (ECM) technique at the cell level is commonly employed for this purpose, combining accuracy and efficiency in the representation of battery operation within the broader powertrain system. In this study, a second-order ECM model of a battery cell is being developed using Modelica, an equation-based modeling language. Parameter lookup tables at multiple levels of state of charge (SoC), extracted from Li-ion battery cells with 4 different commonly used cathode materials, have been utilized. This approach allows for a representation of the battery systems that are used in a wide range of commercial EV applications. To verify the model, an integrated EV model is developed and simulation results of the FTP75 driving cycle have been compared against an equivalent application in MATLAB Simulink. The findings demonstrate a close match between the results obtained from both software across different system points. Specifically, the maximum deviation of SoC is limited to 0.08% and the maximum value of relative voltage deviation is 1.4%. The verified model enables the exploration of multiple possible architecture configurations of EV powertrains with Modelica.

Highly nonlinear characteristics of lithium-ion batteries (LIBs) are significantly influenced by the external and internal temperature of the LIB cell. Moreover, cell temperature beyond the manufacturer’s specified safe operating limit could lead to thermal runaway and even fire hazards and safety concerns to operating personnel. Therefore, accurate information of cell internal and surface temperature of LIB is highly crucial for effective thermal management and proper operation of a battery management system (BMS). Accurate temperature information is also essential to BMS for the accurate estimation of various important states of LIB such as state of charge, state of health and so on. High capacity LIB pack, used in electric vehicles and grid-tied stationary energy storage system essentially consists of thousands of individual LIB cells. Therefore, installing a physical sensor at each cell especially at the cell core is not practically feasible from the solution cost, space and weight point of view. A solution is to develop a suitable estimation strategy which led scholars to propose different temperature estimation schemes aiming to establish a balance among accuracy, adaptability, modelling complexity and computational cost. This article presented an exhaustive review of these estimation strategies covering recent developments, current issues, major challenges, and future research recommendations. The prime intention is to provide a detailed guideline to the researchers and industries towards developing a highly accurate, intelligent, adaptive, easy to implement and compute efficient online temperature estimation strategy applicable to health-conscious fast charging and smart onboard BMS.

ABSTRACT The work is focused on determining the energy transfer from EV’s to grid for different operating conditions. The study has been simulated on a scaled model and later validated through experimental tests on batteries of 20 kWh, 40 kWh, 60 kWh and 80 kWh for EV’s energy rates from 130 Wh/km to 180 Wh/km. Tests have been developed to evaluate the energy transfer from driving distance between 0 and 50 km. Results have proved there is a linear dependence between energy transfer and energy rate. Experimental and simulated values have been correlated showing a 99.6% accuracy. The ratio of energy transfer to battery energy capacity depends not only on this latter parameter, but also on the energy rate of the electric vehicle. Experimental tests have shown a variation from a minimum transfer ratio of 54.1% for the highest electric vehicle energy rate and lowest battery energy capacity and power transfer to grid rate to a maximum of 88.6% for the highest power transfer to grid rate and battery energy capacity and lowest electric vehicle energy rate.

To regulate the growth of battery-based electric vehicles (BEVs) in Indonesia and mitigate their impact on the power grid's supply-demand balance, the government can adjust BEV regulations and offer subsidies. The Jawa-Madura-Bali (Jamali) electrical system, being the largest in Indonesia [1], faces the challenge of accommodating the increasing number of vehicles [2]. Subsequent to analyzing Jamali's electricity supply using data from the National Electricity Company (RUPTL) [3], simulations are constructed to model the grid's demand side. Input variables such as Jamali's population, internal combustion engine (ICE) and electric vehicle populations, initial charging time (ICT), slow- and fast-charging ratios, and BEV charge load curves are simulated. Scenario variables like supply capacity growth speed, vehicle population growth speed, subsidy impact on EV attractiveness, ICT, and fast-charging ratio are subsequently simulated for 2024-2029. Four key simulation outcomes are identified: the best-case scenario (Scenario 1776), achieves the highest EV growth with minimal grid disruption, resulting in a 45.38% EV percentage in 2029 and requiring an annual allocation of 492 billion rupiah to match supply with demand. The worst outcome scenario leads to a 23.12% EV percentage, necessitating 47.566 billion rupiah for EV subsidies in 2029. Additionally, the most and least probable scenarios based on literature research are evaluated. This simulation and its results provide insights into EV growth's impact on the grid's balance in one presidential term from 2024 to 2029 [4], aiding the government in planning regulations and subsidies effectively. Improving the simulation's accuracy depends on refining input variables over time.

This paper presents an improved SOC estimation method for lithium ion batteries in Electric Vehicles using Bayesian optimized feedforward network. This innovative bayesian optimized neural network method attempts to minimize a scalar objective function by extracting hyperpa-rameters (hidden neurons in both layers) using a surrogate model. Furthemore, the hyperparameters are built and data samples are trained and validated. The performance of the proposed deep learning neural network is evaluated. Two reasonable size data samples are ex-tracted from Panasonic 18650PF Li-ion Mendeley datasets that are used for training and valida-tion. RNN and LSTM neural network algorithms offer the common core property of retaining past information and/or hidden states for better SOC estimation. However, the feature of this pro-posed method is the inclusion of Bayesian optimization that chooses optimal double layer hidden neurons. Analysis of results shows that Bayesian optimized feedforward algorithm with average MAPE (0.20%) is the lowest and is the best selection compared with average MAPE for other five deep learning algorithms. In the last quarter of fuel gauge, where fuel anxiety is severe, feed-forward with Bayesian Optimization algorithm is still the best selection (with MAPE of 0.64%).

As one of the critical state parameters of the battery management system, lithium battery state of charge (SOC) can provide an essential reference for battery safety management, charge/discharge control, and energy management of electric vehicles. To analyze the application of deep learning in electric vehicle power battery SOC estimation, this study reviewed the technical process, common public datasets, and the neural networks used, structural characteristics, advantages and disadvantages of lithium battery SOC estimation in deep learning method. First, the specific technical processes of the deep learning method for SOC estimation were analyzed, including data collection, data preprocessing, feature engineering, model training, and model evaluation. Secondly, the current commonly and publicly used lithium battery dataset was summarized. Then, the input variables, data sets, errors, and advantages and disadvantages of four types of deep learning methods, were concluded using the structure of neural network used for training as the classification criterion. Finally, the challenges and future development directions of lithium battery SOC estimation in deep learning method were explained.

The diffusion of electric vehicles (EVs) can be sustained by the presence of integrated solutions offering parking and clean power supply. The recourse to DC systems allows to better integrate EV bidirectional energy exchange, photovoltaic panels and energy storage. In this paper, a methodology for optimal techno-economic sizing of a DC-microgrid for covering EV mobility needs is carried out. It is based on the definition of different scenarios of operation, according to typical EV usage outlooks and environmental conditions. In each scenario, optimal operation is carried out by means of a specific approach for EV commitment on different stations. The sizing procedure is able to handle the modular structure of microgrid devices. The proposed approach is applied to a case study of envisaged EV service fleet for Bari port authority.

The purpose of this research is to present a thorough evaluation of the energy management system, which consists of hybrid energy storage systems, and its control algorithms, which may be used in electric vehicles. This paper outlines the characteristics of electric vehicles, research methods, analysis of the hybrid energy storage system architecture, converter topology, and energy management techniques. The strength and co-occurrence of keywords over the past ten years are shown in this study using a systematic research framework for performing a literature review and using keyword analysis techniques. The study reveals a pattern of recently and frequently used terms in works of literature. Consequently, their suitability, benefits, and drawbacks are assessed. In this study, the hybrid energy storage system and converter circuit architecture are evaluated and rated. Non-isolate DC-DC converter converter connected to SC is a suitable configuration for the hybrid converter because it is simple to build, reliable, and has minimal loss/weight/cost, which improves vehicle performance. In terms of the application of control strategies, it is shown that deterministic and fuzzy rule-based control techniques are successfully assessed using real-scale vehicle experiments and selected for manufacturing. On the other hand, real-time optimization-based energy management techniques have been effectively shown in lab-scale tests and may be used in a future real-scale vehicle.

The enormous growth in the penetration of electric vehicles (EVs), has laid the path to advancements in the charging infrastructure. Connectivity between charging stations is an essential prerequisite for future EV adoption to alleviate users’ “range anxiety”. The existing charging stations fail to adopt power provision allocation and scheduling management. To improve the existing charging infrastructure data based on real-time information and availability of reserves at charging stations could be uploaded to the users to help them locate the nearest charging station for an EV. This research article focuses on an a interactive user application developed through SQL and PHP platform to allocate the charging slots based on estimated battery parameters, which uses data communication with charging stations to receive the slot availability information. The proposed server-based real-time forecast charging infrastructure avoids waiting times and its scheduling management efficiently prevents the EV from halting on road due to battery drain out. The proposed model is implemented using a low-cost microcontroller and the system etiquette tested.

The potential of metallic lithium to become the anode material for next-generation batteries is hampered by significant challenges, chief among which is dendrite growth during battery charging. These dendritic structures not only impair battery performance but also pose safety risks. Among the non-destructive analytical techniques in battery research, Magnetic Resonance Imaging (MRI) stands out as a promising tool. However, the direct imaging of lithium by 7Li MRI is hindered by its low sensitivity and spatial resolution, making its use for of dendritic growth imaging very difficult. Instead, a recently introduced indirect imaging approach based on 1H MRI of the electrolyte was used in this study. This method was used for sequential 3D imaging to monitor the charging process of lithium metal symmetric cells in three different electrical circuits: single cell, four cells in parallel, four cells in series. The measured sequential images allowed measurement of dendrite growth in each cell using volumetric analysis. The growth results confirmed the theoretical expectation that growth across cells is uneven in a parallel circuit and even in a series circuit. The methods presented in this study can be applied also to many other dendrite-related issues in batteries.

Efficient processing of end-of-life lithium-ion batteries of electric vehicles is important and a pressing challenge for a circular economy. Regardless of whether the processing strategy is recycling, repurposing or remanufacturing, the first processing step would usually involve disassembly. As battery disassembly is a dangerous task, efforts have been made to robotise it. In this paper, a robotic disassembly platform using four industrial robots is proposed to automate the non-destructive disassembly of a plug-in hybrid electric vehicle battery pack into modules. The work was conducted as a case study to demonstrate the concept of autonomous disassembly of an electric vehicle battery pack. A two-step object localisation method based on visual information is used to overcome positional uncertainties from different sources and is validated by experiments. Also, the unscrewing system is highlighted, and its functions, such as handling untightened fasteners, loosening jammed screws, and changing the nutrunner adapters with square drives, are detailed. Furthermore, the time required for each operation is compared with that taken by human operators. Finally, the limitations of the platform are reported and future research directions are suggested.

Large lithium-ion batteries (LIBs) in electric vehicles and energy storage systems demonstrate different performance and lifetime compared to small LIB cells, owing to the size effects generated by the electrical configuration and property imbalance. However, the calculation time for performing life predictions with three-dimensional (3D) cell models is undesirably long. In this paper, a lumped cell model with equivalent resistances (LER cell model) is proposed as a reduced order model of the 3D cell model, which enables accurate and fast life predictions of large LIBs. The developed LER cell model is validated via the comparisons with results of the 3D cell models by simulating a 20-Ah commercial pouch cell (NCM/graphite) and the experimental values. In addition, the LER cell models are applied to different cell types and sizes, such as a 20-Ah cylindrical cell and a 60-Ah pouch cell.

Electric vehicles can effectively make use of the time-of-use electricity price to reduce the charging cost, meanwhile using the grid power to preheat the battery before departure is particularly important for improving the vehicle mileage and reducing the use cost.In this paper, a dynamic programming algorithm is used to optimize the battery AC charging-preheating strategy to minimize the total cost of battery charging and preheating, with the charging current and battery preheating power consumption as the control variables. The cost difference between the optimized control strategy and the conventional preheating strategy was analyzed under different ambient temperatures (-20℃~ 0℃) and different target travel time (7:00 ~ 12:00). The simulation results show that the optimized control strategy makes the battery SOC and temperature reach the set value at the user's target departure time, and the total cost of the grid is the lowest. Compared with the conventional preheating strategy, the optimized control strategy can utilize the power grid energy in the valley price area, reduce the opening time of water heating PTC in the flat and the peak price zones, and the cost utilization rate can reach 18.41% ~ 73.96%, and the cost-saving effect is significant.

This study provides a comprehensive analysis of global patent trends in battery recycling, focusing on secondary batteries and related technologies across Korea, China, and the United States. The data, collected from various patent databases, was quantitatively analyzed to identify technology trends and direct future development. The analysis reveals distinct emphases on technologies such as lithium-ion and waste battery recycling, highlighting notable differences in patent activities among key companies and countries. China's large number of patents in battery manufacturing processes contrasts with the USA's focus on electrochemical cell construction and storage systems, while Korea shows significant activity in waste battery technology. The study underscores the competitive landscape and innovation efforts in the battery recycling sector, providing insights into the technological focuses and priorities of each country. It also identifies key challenges, such as the need for consistent innovation and broader geographic coverage in Korea, enhancing patent influence and international presence in China, and ensuring high patent quality and fostering innovation in lagging sectors in the United States. Addressing these challenges through enhanced collaboration, increased R&D investments, and supportive policies is crucial for strengthening the global position and driving further innovation in the battery recycling sector.

UN Convention on Climate Change 2015 mandates reducing carbon footprint to reduce global warming. Considering environmental concerns, Electric Vehicles (EVs) spearhead the move towards green mobility. Niti Aayog (Indian Government) has envisaged an “EV only” scenario by 2030. Two wheelers dominate the Indian automobile industry with almost 80% market share. With the transportation sector accounting for 70% of world’s fossil fuels use, the need for a sustainable supply chain which addresses environment, economy and societal issues, has, of late, aroused interest in the business academic community and industries. Sustainability in business decision-making promotes efficiency, controls expenditure, enhances customer delight, increases sales and market share, optimises risk management strategy, and promotes profitability. This study intends to develop a conceptual framework after examining research gaps in sustainable supply chain management (SSCM) and allied topics like sustainability, green supply chain management, and vendor partnerships through collaborative efforts. Even the UN vide Goal 9 of sustainable goals pertaining to industry, highlights the importance of this framework.

Battery electric vehicles provide an opportunity to balance supply and demand in future power systems with high shares of fluctuating renewable energy. Compared to other storage systems such as pumped-storage hydroelectricity, electric vehicle energy demand is highly dependent on charging and connection choices of vehicle users. We present a model framework of a utility-based stock and flow model, a utility-based microsimulation of charging decisions, and an energy system model including respective interfaces to assess how the representation of battery electric vehicle charging affects energy system optimization results. We then apply the framework to a scenario study for controlled charging of nine million electric vehicles in Germany in 2030. Assuming a respective fleet power demand of 27 TWh, we analyze the difference between power-system-based and vehicle user-based charging decisions in two respective scenarios. Our results show that taking into account vehicle users’ charging and connection decisions significantly decreases the load shifting potential of controlled charging. The analysis of marginal values of equations and variables of the optimization problem yields valuable insights on the importance of specific constraints and optimization variables. In particular, state-of-charge assumptions and representing fast charging drive curtailment of renewable energy feed-in and required gas power plant flexibility. A detailed representation of fleet charge connection is less important. Peak load can be significantly reduced by 5% and 3% in both scenarios, respectively. Shifted load is very robust across sensitivity analyses while other model results such as curtailment are more sensitive to factors such as underlying data years. Analyzing the importance of increased BEV fleet battery availability for power systems with different weather and electricity demand characteristics should be further scrutinized.

In current electric vehicles, the traction battery is intended to store energy. When designing this battery different parameters must be taken into account in order to arrange the battery/module/cells in the mechanically and thermally safest configuration. Moreover, the battery layout must have a correct dynamic behavior in possible collisions. In the present study, different battery configurations plus added energy absorbers are analyzed. In order to do that, an internal combustion vehicle modeled with finite elements is applied as the reference model. The structural behavior of the different battery configurations in the event of a side collision is examined. Firstly, the safest arrangement is stablished, both with respect to cabin intrusion and thermal runaway propagation. Secondly, the safest arrangement that guarantees the safety of the occupants in the event of a side collision is analyzed but using the MADYMO. This software includes experimentally validated dummies which allow have an insight in the stresses experienced by occupants. On the one hand, the analysis states that the battery pack inclusion in the vehicle increases the stiffness of the car floor, resulting in fewer intrusions in the passenger compartment. Therefore, a greater safety for the occupants is reached. On the other hand, none of the configurations analyzed has shown enough safety against the phenomenon of Thermal Runaway.

Abstract: This study investigates the effect of Electric Vehicle Charging Stations (EVCS) on light-duty Electric Vehicle sales and the Total California rebates. Electric Vehicle Charging Stations (EVCS) are infrastructure facilities that allow for the charging of electric vehicles (EVs). I applied the before and after model with California state county using its community-level attributes and used the difference-in-difference design to identify a strategy for estimating the causal effects of these attributes. These attributes include EVCS installations by time, EV sales by time, rebate applications by time, the number of multi-unit housing units, and the median income levels. The empirical ev-idence of this study shows the estimated relationship between public EV charging installation and EV sales overall by community income level, housing density, and other relevant factors, the result shows that EVCSs is highly correlated with light duty Electric Vehicle adoption. For the investors, policymakers, and other stakeholders, this study provides evidence of a threshold of EVCS on Light Duty Electric Vehicle adoption and rebate in California.

Hybrid electric vehicles are certainly one of the key solutions for improving fuel efficiency and reducing emissions, especially in special vehicle application and with the use of CO2 neutral fuels. Determining the energy management strategy and finding the optimal solution with regard to the aforementioned goals re-mains the one of the main challenges in the design of HEV. This paper presents a new vehicle modeling method, with an emphasis on HEVs, which is based on the frequency analysis of emissions and consumption according to the current specific traction power of the vehicle. The evaluation of the newly introduced model in the RDE, NEDC and WLTP cycle was performed and the results were compared with the standard verified vehicle model that was created in AVL's CruiseM software package. Positive traction energies have positive deviations of between 0.35% and 2.85%. The largest deviation in CO2 emissions was recorded for the HEV model in the RDE cycle and in the non-hybrid model in the WLTP cycle of 3.79% and 4.4% respectively, all other combinations of cycle and vehicles had deviations of up to about 1%. As expected, the largest relative deviations were recorded for NOx emissions from 0.13% to 9.62% for HEV in the WLTP cycle.

A pivotal strategy in decarbonizing the transport sector is by transitioning from internal combustion engine vehicles (ICEVs) to electric vehicles (EVs), especially if they are charged with renewable energy. To provide an incentive to the common populace to switch to EVs, cities should set up - or enable or even encourage the private sector to do so - electric vehicle charging stations (EVCS) at multiple and suitably accessible locations. This paper aims to present a digitaltwin-enabled methodology study for selecting the most suitable possible locations to establish EVCS with consideration of the low voltage (LV) network operation in terms of power losses, active and reactive power in EV charging demand and the effect of the EVCS on the transformers, based on examples in Newcastle upon Tyne (England, UK). It also evaluates the most suitable type of charger that could be installed at these locations by studying the estimated traffic, cost and impact of the EVCS on the power grid, both at peak and off hours. This paper demonstrates how digitaltwin technologies, such as the web-based tool AutoDesign by Northern Powergrid and EA Technology and open source Pandapower can be used for identifying the most viable and cost-effective locations to connect EVCSs to a Distribution Network Operators (DNO)’s LV network. The results of the analysis indicate that with the installation of the most suitable type of EVCS in a particular location, the local power grid would not be significantly affected at any hour of the day.

This study conducts a comprehensive review of the integration of Hybrid Electric Turbochargers in mass-produced road vehicles. The primary objective is to inform the readers about the potential advantages and innovative applications of HETs. Employing a SWOT analysis, the research compares the performance of HETs on thermal engines versus traditional turbochargers and HETs on thermal engines versus HETs on hybrid engines based on a synthesis of multiple research findings. The study elucidates the fundamental mechanics of turbochargers, emphasizing their inherent benefits. Additionally, it introduces a novel approach with the integration of the hy-brid-electric turbocharger, demonstrating its capacity, supported by practical examples. The in-corporation of turbochargers with energy recovery mechanisms, including HETs, is shown to significantly contribute to emissions reduction. Moreover, the electric drive facilitates the utili-zation of hybrid turbines, particularly on low-displacement engines, resulting in enhanced effi-ciency, torque, and liter power. In conclusion, the research underscores the potential of HETs to substantially mitigate the environmental impact of the transportation sector by reducing emis-sions and conserving energy. Their ability to optimize the fuel efficiency and power output of internal combustion engines, coupled with the feasibility of downsized engines, positions HETs as an attractive option for both manufacturers and consumers. However, it is acknowledged that the implementation of HETs is in its early stages, necessitating further research to comprehensively understand their environmental impact. Despite this, the promising positive impact on the en-vironment designates HETs as a technology deserving close attention in the forthcoming years.

Solar powering the increasing fleet of electrical vehicles (EV) demands more surface area than may be available for photovoltaic (PV) powered buildings. Parking lot solar canopies can provide the needed area to charge EVs, but are substantially costlier than roof- or ground-mounted PV systems. To provide a lower-cost PV parking lot canopy to supply EV charging beneath them, this study provides a full mechanical and economic analysis on three novel PV canopy systems: (1) exclusively wood, single parking spot spanning system, (2) wood and aluminum double parking spot spanning system, and (3) wood and aluminum cantilevered system for curbside parking. All systems can be scalable to any amount of EV parking spots. The complete designs and bill of materials (BOM) of the canopies are provided along with basic instructions and are released with an open source license that will enable anyone to fabricate them. The results found single-span systems have cost savings of 82%-85%, double-span systems save 43%-50%, and cantilevered systems save 31%-40%. In the first operation year, the PV canopies can provide 157% of energy needed to charge the least efficient EV currently on the market if it is driven the average driving distance in London ON, Canada.

Electric vehicles (EVs) play a significant role in reducing carbon emissions. In the US, EVs are mostly owned by multi-vehicle households, and their usage is primarily studied in the context of vehicle miles traveled. This study takes a unique approach by analyzing EV usage through the lens of vehicle choice (between EVs and internal combustion engine vehicles) within multi-vehicle households. A two-step machine-learning framework (clustering and decision trees) is proposed. The framework determines the preferred trip category for EV use and captures the effects of household attributes, driver attributes, built-environment factors, and gas prices on EV use in multi-vehicle households. Results indicate that discretionary trips (accumulated local effect = 0.037) are mostly preferred for EV use. EV preference is more pronounced among households with fewer workers (<2) and lower income levels. These findings are valuable for policymakers and auto manufacturers in targeting specific market segments and promoting EV adoption.

The widespread adoption of electromobility constitutes one of the measures designed to reduce air pollution caused by traditional fossil fuels. However, several factors are currently impending this process, ranging from insufficient charging infrastructure, battery capacity, long queueing and charging time, to psychological factors. On top of range anxiety, the frustration of the EV drivers is further fueled by the lack the uncertainty of finding an available charging point on their route. To address this issue, we propose a solution that comes to bypass the limitations of the Reserve now function of the OCPP standard, enabling drivers to make charging reservations for the upcoming days, especially when planning a longer trip. We created an algorithm that generates reservation intervals based on the charging station's reservation and transaction history. Subsequently, we ran a series of test cases that yielded promising results, with no overlapping reservations.

In this study, the external magnetic field emitted by a wireless power transfer (WPT) system and the internal electric field induced into human body models during recharging operations of a compact electric vehicle (EV) are evaluated. To this aim an ad-hoc formulation for the source modeling is coupled with a commercial software that performs numerical dosimetry. Specifically, two realistic anatomical models both in a driving position and in a standing posture are considered, and the chassis of the EV is modeled either as a currently employed aluminum alloys and as a futuristic carbon fiber composite panel. Aligned and misaligned coil configurations of the WPT system are considered as well. The analysis of the obtained results shows that the ICNIRP reference levels are exceeded in the driving position, especially for the carbon fiber chassis, whereas no exceedance is observed in terms of basic restrictions, at least for the considered scenarios.

This paper presents a thermal runaway prognosis scheme based on the big-data platform and entropy method for battery systems in electric vehicles. It can simultaneously realize the diagnosis and prognosis of thermal runaway caused by the temperature fault through monitoring battery temperature during vehicular operations. A vast quantity of real-time voltage monitoring data was collected in the National Service and Management Center for Electric Vehicles (NSMC-EV) in Beijing to verify the effectiveness of the presented method. The results show that the proposed method can accurately forecast both the time and location of the temperature fault within battery packs. Furthermore, a temperature security management strategy for thermal runaway is proposed on the basis of the Z-score approach and the abnormity coefficient is set to make real-time precaution of temperature abnormity.

In this paper, we examined the temperature variations of key constituents during the operational cycle of a custom-built electric vehicle. The vehicle was made employing a motor of 10kW, a KLS7275D controller, and a lithium-ion battery. Temperature sensors for monitoring was affixed to the motor, controller, and battery, facilitating a comprehensive analysis of thermal behaviors. A controlled 20 minute driving tests encompassing both high and low speeds were executed to scrutinize temperature variations. Our findings reveal that the controller exhibited the most substantial temperature fluctuation compared to the battery and motor. Results shows the importance of thermal management strategies for components to ensure optimal driving performance and component reliability in electric vehicles.

This work targets the development of a mobility control system for high-speed series hybrid electric tracked vehicles, which operate with independent traction motors for each track. The scope of the research encompasses the modeling of the series hybrid powertrain specific to military tracked vehicles, as well as an in-depth analysis of their dynamic behavior. Subsequently, the study conducts a critical review of the mobility control approaches sourced from literature, identifying key techniques relevant to high-inertia vehicular applications. Building on the foundational models, the study puts forward a robust closed-loop mobility control system aimed at ensuring precise and stable off-road vehicle operations. The system's resilience and adaptability to a variety of driving conditions are emphasized, with a particular focus on handling maneuvers such as steering and pivoting, which are challenging operations for tracked vehicle agility. The performance of the proposed mobility control system is tested through a series of simulations, covering a spectrum of operational scenarios. These tests are carried out in both offline simulation settings, which permit meticulous fine-tuning of system parameters, and real-time environments that replicate actual field conditions. The simulation results demonstrate the system's capacity to improve vehicular response and highlight its potential impact on the future designs of mobility control systems for the heavy-duty vehicle sector, particularly in defense applications.

To enable the deployment of battery-electric vehicles (BEV) as passenger cars in the private transport sector, a suitable charging infrastructure is crucial. In this paper a methodology for efficient spatial distribution of charging infrastructure is evaluated by investigating a scenario with a market penetration of BEVs of 100 percent (around 1.3 million vehicles). It aims towards the development of various charging infrastructure scenarios - including public and private charging - which are suitable to cover the charging demand. Therefore, these scenarios are investigated in detail with focus on number of public charging points, their spatial distribution, the available charging power and the necessary capital costs. For the creation of those charging infrastructure scenarios a placement model is developed. It uses the data of a MATSim (Multi-Agent Transport Simulation) traffic simulation of the metropolitan area of Berlin to evaluate and optimize different distributions of charging infrastructure. The model uses a genetic algorithm and the principle of multi-objective optimization. The capital cost of the charging points and the mean detour car drivers must cover additionally are used as optimization criteria. Using these criteria should lead to cost efficient infrastructure solutions which provide high usability at the same time. The main advantage of the method selected is that multiple optimal solutions with different characteristics can be found and suitable solutions can be selected by using other criteria subsequently. The optimized charging infrastructure solutions show capital costs between 624 and 2950 million euro. Users must cover an additionally mean detour of 254m to 590m per charging process to reach an available charging point. According to the results a suitable ratio between charging points and vehicles is between 11:1 and 5:1. A share of fast charging infrastructure (&gt;50kW) of less than ten percent seems to be sufficient, if it is situated at main traffic routes and highly frequented places.

The work aims to improve the battery performance in hybrid electric vehicles (HEVs) by reducing the vehicle speed. We develop a specific protocol for managing battery use and optimizing the energy consumption rate to achieve this goal. The protocol automatically controls the driving operation, avoiding incompatible driving patterns with energy-saving mode and performance improvement. The protocol is submitted to a simulation process to predict the energy rate lowering and battery performance enhancement. The proposed protocol applies to any hybrid electric vehicle type and route conditions since it uses vehicle mass, drag and rolling coefficients, and road slope as variable parameters to determine the minimum energy consumption rate. We run experimental tests to validate the simulation data and the proposed protocol. Furthermore, the protocol applies to variable starting vehicle speeds, from 10 to 50 km/h, corresponding to the current driving patterns, sport, normal, and eco, set up by car manufacturers. A reduction of 10% in vehicle speed in urban and peripheral routes achieves a minimum energy rate, enhancing battery management. Current vehicle speed shows a deviation from optimum management of 18% while applying the vehicle speed reduction limits the deviation to 0.2%. Experimental results show a good agreement with simulation data with 94% accuracy. We tested the protocol for urban and peripheral routes with maximum vehicle speed limits of 60 and 90 km/h.

Even though the current classic aerospace propulsion methods are greatly improved, some of the most modern methods have already been introduced, among which the propulsion with electric motors. Energy can be obtained from hydrogen burners, honeycomb burners to protect the burning of hydrogen that burns 10 times faster than conventional oil fuels or alcohols. Hydrogen storage is also done in honeycomb cell reservoirs. Getting solar photovoltaic power even during flight is not yet profitable or efficient, but it can be proposed in the future for lighter and/or spacecraft. A great desire is to dismantle water in hydrogen and oxygen directly on the aircraft, so the stored fuel is actually water and the one actually used is the hydrogen removed from the water. In this case, there is no need for hydrogen storage. And other modern methods of propulsion and energy acquisition are briefly presented in the paper.

Biomass materials have received attention for energy storagebecaused of the advantage of low-cost, easy-to-prepare, and eco-friendliness. Three-dimensional carbon materialswith abundant pore structure gradually becomeresearch hotspot in high-performance energy storage. In this study, an easy-to-prepare, green, light and elastic activated carbon was present using the biomass Juncus effusus (JCE) via high-temperature pyrolysis, followed by activation in air. Compared with previously reported bio-carbons, the proposed air-activated bio-carbon contributes in the fabrication of pores to preserve the interconnected, reticular and tubular structure. Moreover, the interconnected porous material also inherits the excellent tenacity of the original JCE such as the material can be bended to below 90^o under an external force while maintaining structural integrity. The activated porous carbon material exhibits an enhanced electric double-layer capacitance (~210 F g^-1 at 1 A g^-1), with capacitance retention of ~78.62% at 10 A g^-1. The interconnected porous carbon microtubes electrode as a double-layer symmetric capacitor exhibits considerable capacitance retention (84%) after 2000 cycles at 1 A g^-1. The improved energy storage performance was proposed to be attributed to the shortened ionic diffusion distance and sufficient contact between the interface of the carbon electrode and electrolyte, which is resulted from the elastic, undamaged structure and types of pores. These results demonstrated that as-preparedcarbon materials have potentional application in symmetric capacitors.

In the electric distribution systems, the “Smart Grid” concept is implemented to encourage energy savings and integration of the innovative technologies, helping the Distribution Network Operators (DNOs) in choosing the investment plans which to lead the optimal operation of the networks and increasing the energy efficiency. In this context, a new phase load balancing algorithm was proposed to be implemented in the low voltage distribution networks with hybrid structures of the consumption points (switchable and non-switchable consumers). It can work in both operation modes (on-line and off-line), uploading information from different databases of the DNO which contain: the consumers’ characteristics, the real loads of the consumers integrated into the Smart Metering System (SMS), and the typical load profiles for the consumers non-integrated in the SMS. The algorithm was tested in a real network, having a hybrid structure of the consumption points, on a time interval by 24 hours. The obtained results were analyzed and compared with other algorithms from the heuristic (Minimum Count of Loads Adjustment algorithm) and the metaheuristic (Particle Swarm Optimization and Genetic Algorithms) categories. The best performances were provided by the proposed algorithm, such that the unbalance coefficient resulted in the smallest value (1.0017). The phase load balancing led to the following technical effects: decreasing the average current in the neutral conductor with 94% and for the energy losses with 61.75 %, and increasing the minimum value of the phase voltage at the farthest pillar with the 7.14 %, compared to the unbalanced case.

Electric Vehicles (EVs) are the need of the hour due to growing climate change problems linked with the transportation sector. Battery Thermal Management System (BTMS), which is accountable for certifying safety and performance of lithium-ion batteries (LiB), is the most vital part of an EV. LiB has auspicious gravimetric energy density but the heat generation due to chemical reactions inside a LiB during charging and discharging causes temperature rise which has a direct effect on LiB performance and safety. This study specifically focuses on aircooled BTMS, defines different types of air-cooled BTMS (active and Passive), discusses limitations associated with air-cooled BTMS, and investigates different optimization techniques and parameters to improve performance of air-cooled BTMS. Maintaining temperature within optimum range and uniform temperature distribution between cells of a battery pack are the major design parameters for improving the performance and efficiency of air-cooled BTMS. Various optimization techniques including cell arrangement with a battery pack, air-flow channel optimization, and air inlet/outlet position variations are discussed and each technique is thoroughly reviewed. Finally, it’s noted that passive air-cooled BTMS is not that effective for long-distance vehicles so most researchers shifted their focus toward active air-cooled BTMS. Active air-cooled BTMS requires a lot of power for effective performance. Lastly, the most recent field of air-cooled BTMS technology which is Air-Hybrid BTMS is discussed and declared a very promising solution for overcoming major limitations associated with air-cooled BTMS.

Recently, Electric Two-Wheelers ETW are changing the face of the global automotive market. This study focused on selecting proper material and mechanical isolation gap to design a protective enclosure for the battery pack of ETW. The integration of the Failure, Modes, Mechanism and Effect Analysis (FMMEA) method is utilized to develop the interface matrix and the severity index of different components of the enclosure. By analyzing different forces from the road conditions, dynamics during turn, acceleration, and deceleration with the enclosure, it becomes a crucial load-bearing element. Employing Finite Element Modeling (FEM), structural strength using materials like AL6061, Q235, C22000, DC 01 and Teflon are assessed under varying static, dynamic and thermal conditions. Modal analysis is conducted to observe the excitation frequencies where the maximum deformation for the metal enclosure is observed beyond 500Hz. AL6061 material that can withstand the stresses and deformations that are under allowable stress limits with negligible deformation is most preferable material based on the results. Minimal of 2.5 mm gap to be provided in case of metal casing and 10mm in case of Teflon is proven.

Unmanned vehicles (UVs) have become increasingly important in various scenarios of civil and military operations. The present work aims at the conceptual design of a modular Amphibious Unmanned Ground Vehicle (A-UGV), that can be easily adapted for different types of land and/or water missions, with low monetary cost (&lt;5k€, without sensors). Basing the design on the needs highlighted in the 2021 review of the Strategic Directive of the Portuguese Navy, the necessary specifications and requirements are established for two mission scenarios. Then a market research analysis focused on vehicles currently available, and their technological advances, is conducted to identify existing UVs solutions and respective characteristics/capabilities of interest to the current work. To study and define the geometry of the hull and the configuration of the A-UGV itself, preliminary computational structural and fluid analyses are carried out to ensure it complies with the specifications initially established. As a result, one obtains a fully electric vehicle, with approximate dimensions of 1050×670×450mm (length-width-height), enabled with 6×6 traction capable of reaching 20km/h in land, possesses amphibious capabilities of independent propulsion in water up to 8kts, and with an estimated autonomy of over 60 minutes.

This article investigates the source of booming noise emanating from the tailgates of electric vehicles, along with proposed strategies to mitigate it. This study involved the measurement of booming noises during on-road vehicle tests to pinpoint their origins. Additionally, operational deflection shapes (ODS) were extracted from the tailgate vibration signals to gain insight into its dynamic behavior. Modal tests were conducted on the tailgate to determine its dynamic characteristics and compared with driving test results to reveal the mechanism responsible for tailgate-induced booming noise. It was established that such noise is primarily due to the tailgate modes resulting from a combination of rigid body motion in the fore-aft direction and deformation in the central section of the panel. An analytical model of the tailgate was developed using commercial finite element analysis software to propose measures for reducing booming noise. Experimental findings validated the model accuracy. Structural enhancements were implemented to enhance the panel stiffness and improve the connection between the vehicle and tailgate via bushings to dampen the booming noise resulting from tailgate motion. Under random force inputs, analytical results demonstrated a 13.8% reduction in maximum deformation in the tailgate model in the improved structural configuration with increased panel stiffness.

We consider the problem of coordinating the charging of an entire fleet of electric vehicles (EV), using a model-free approach, i.e. purely data-driven reinforcement learning (RL). The objective of the RL-based control is to optimize charging actions, while fulfilling all EV charging constraints (e.g. timely completion of the charging). In particular, we focus on batch-mode learning and adopt fitted Q-iteration (FQI). A core component in FQI is approximating the Q-function using a regression technique, from which the policy is derived. Recently, a dueling neural networks architecture was proposed and shown to lead to better policy evaluation in the presence of many similar-valued actions, as applied in a computer game context. The main research contributions of the current paper are that (i)we develop a dueling neural networks approach for the setting of joint coordination of an entire EV fleet, and (ii)we evaluate its performance and compare it to an all-knowing benchmark and an FQI approach using EXTRA trees regression technique, a popular approach currently discussed in EV related works. We present a case study where RL agents are trained with an epsilon-greedy approach for different objectives, (a)cost minimization, and (b)maximization of self-consumption of local renewable energy sources. Our results indicate that RL agents achieve significant cost reductions (70--80%) compared to a business-as-usual scenario without smart charging. Comparing the dueling neural networks regression to EXTRA trees indicates that for our case study's EV fleet parameters and training scenario, the EXTRA trees-based agents achieve higher performance in terms of both lower costs (or higher self-consumption) and stronger robustness, i.e. less variation among trained agents. This suggests that adopting dueling neural networks in this EV setting is not particularly beneficial as opposed to the Atari game context from where this idea originated.

Electric torque wrenches play a crucial role in the assembly of high-strength bolts. This study focuses on three assembly processes for high-strength bolts and introduces a statistical analysis method to assess the quality of the bolt assembly. To enhance the performance, a novel, fully digital, Internet of Things (IoT) electric torque wrench is designed, incorporating a smart meter chip. This wrench achieves integration between the current sensor control method and the torque sensor control method using a simplified hardware circuit, ensuring high precision and stability. Additionally, this study employs the AC voltage self-stabilization method and Savitzky–Golay filtering method to enhance the accuracy and robustness of the wrench. Simulation experiments using Simulink and Matlab validate the effectiveness of these two methods. Furthermore, a cloud platform is utilized to enable rapid IoT access for the wrench, facilitating seamless connectivity and data transmission.

Analysis of 1382 measures of battery State of Health (SoH) from 283 Nissan Leafs (“Leaf/s”), manufactured between 2011 and 2017, has detected a faster rate of decline in this measure of energy-holding capacity for 30 kWh variants. At two years of age, the mean rate of decline of SoH of 30 kWh Leafs was 9.9% per annum (95% uncertainty interval of 8.7% to 11.1%; n = 82). This was around three times the rate of decline of 24 kWh Leafs which at two years averaged 3.1% per annum (95% uncertainty interval of 2.9% to 3.3%; n = 201). For both variants there was evidence for an increasing rate of decline as they aged, although this was much more pronounced in the 30 kWh Leafs. Higher use of rapid DC charging was associated with a small decrease in SoH. Additionally, while 24 kWh cars with greater distances travelled showed a higher SoH, in 30 kWh cars there was a reduction in SoH observed in cars that had travelled further. The 30 kWh Leafs sourced from United Kingdom showed slower initial decline than those from Japan, but the rate of decline was similar at two years of age. Improvements in the battery health diagnostics, continuous monitoring of battery temperatures and state of charge, and verification of a fundamental model of battery health are needed before causes and remedies for the observed decline can be pinpointed. If the high rate of decline in battery capacity that we observed in the first 2.3 years of a 30 kWh Leaf’s lifetime were to continue, the financial and environmental benefits of this model may be significantly eroded. Despite 30 kWh Leafs accounting for only 14% of all light battery electric vehicles registered for use on New Zealand roads at the end of February 2018, there is also the potential for the relatively poor performance of this specific model to undermine electric vehicle uptake more generally unless remedies can be found.

The use of cobalt-iron (VaCoFe) core is investigated as an alternative to silicon-iron (FeSi) on the design of interior permanent magnet synchronous motors (IPMSM). A spoke-type IPMSM geometry is optimized considering FeSi and VaCoFe cores for a torque range up to 40 N.m, providing a general comparative analysis between materials, considering the application of a 4-motor competition vehicle’s powertrain. A genetic optimization algorithm is applied over a hybrid analytical/finite-element model of the motor to provide sufficiently accurate electromagnetic and thermal results within a feasible time. VaCoFe can result in an estimated increase of up to 5 % in efficiency for the same torque, or up to 64 % torque increase for the same efficiency level. After optimization, and using a detailed time-dependent model, a potential 3.2 % increase in efficiency, a core weight reduction of 4.1 %, and a decrease of 9.6 % in the motor’s core volume was found for the VaCoFe at 20 Nm. In addition, for the same motor volume, the VaCoFe allows an increase of 51.9 % of torque with an increase of 1.1 % of efficiency, when compared with FeSi.

The abrupt increase of the electric vehicles in Bangladesh needs huge amount of power. As a result, alternative energy sources are emphasized due to limited fossil fuels in order to develop a sustainable energy sector with environment friendly resources. Bangladesh has an enormous potential in the field of renewable resources like biogas and biomass. This paper presents 20 kW electric vehicle charging station (EVCS) utilizing biogas resources where maximum energy requirement is 100 kWh. In this paper, the biogas based EVCS is designed using MATLAB Simulink and HOMER software. Daily 15-20 electric vehicles can be recharged their batteries using the proposed charging station. The proposed system offers lower cost of energy compared to the grid electricity. Moreover, the proposed charging station shows 68.75% reduction in CO₂ emission than grid based charging station. In addition, the proposed EVCS will save monthly $ 16.25 and $ 27.50 respectively for easy bike and auto rickshaw type electric vehicles in Bangladesh.

With a relatively small population, Russia accesses huge oil, natural gas, coal and uranium resources, and hosts advanced nuclear energy, oil and natural gas industries. However, the combined effect of today’s low cost electricity generation via photovoltaic modules, water and wind turbines and similarly low cost storage in Li-ion battery and solar hydrogen obtained via water electrolysis will have a profound impact on Russia’s energy and automotive industries.

(1) Background: In order to study the effects of different electric cookers on the nutritional components of millet porridge, five different electric cookers were selected to cook millet porridge, and sensory and nutritional components in millet porridge, millet soup, and millet grains were analyzed. (2) Methods: Using principal component and cluster analysis, a variety of nutritional components were comprehensively compared. (3) Results: The results showed that among the different cooked samples, the content of amylose and reducing sugar was the highest in the samples cooked by electric cooker no. 3. The electric cooker no. 4 samples had the highest sensory evaluation score, crude fat, and protein content. The contents of ash, fatty acids, bound amino acids, and minerals were the highest in the electric cooker no. 5 samples. The sensory evaluation score and content of crude fat, ash, reducing sugar, direct starch, and Cu were higher in millet grains than in millet soup or porridge. The content of fatty acid, protein, amino acid, Zn, Fe, Mg, Mn, and Ca was highest in millet soup. Different electric cookers produced millet porridge with varying nutritional levels. (4) Conclusions: This study provides a reference for the further development of new electric cookers.

Energy efficiency and leakage magnetic field (LMF) are two important issues in electric vehicle inductive chargers. In this work, the maximum achievable coil efficiency and the corresponding LMF strength are formulated as functions of hardware parameters, and figure of merits (FOM) are proposed for assessing the efficiency and LMF performance of the coil assembly pair. The impacts of the coil assemblies’ geometric parameters on both FOMs are examined with the aid of finite element analysis (FEA), and measures to improve the FOMs are extracted from FEA results. A coil assembly pair is manually optimized within given dimensional limits. Compared with the initial design, the optimized one achieves higher efficiency and lower LMF strength while consuming less copper. The performance improvement is verified by FEA results and experimental data measured on an 85 kHz electric vehicle inductive charger prototype. The key measures for coil assembly optimization are summarized.

In this study, we focused on the eco-driving of electric vehicles (EVs). The target vehicle is an electric bus developed by our research team. Using the parameters of the bus and speed pattern optimization algorithm, we derived the EV eco-driving speed pattern. Compared to eco-driving of internal combustion engine vehicles (ICVs), we found several different characteristics. We verified these characteristics with actual vehicle driving test data of the target bus, and the results confirmed its rationality. The EV eco-driving method can improve electricity consumption by about 10% - 20% under the same average speed.

South Korea proposed reducing greenhouse gas emissions by 37% compared to the expected emissions by 2030 as the POST-2020 greenhouse gas reduction target. Electric vehicle distribution in the public sector is essential to achieve the carbon dioxide reduction target for transportation. In particular, when buses with internal combustion engines, which travel long distances and contribute substantially to greenhouse gas emissions, are replaced with electric buses, it is expected that greenhouse gas emissions will be significantly reduced. There are three types of electric buses with different power supply systems: a plug-in type in which power is supplied when a plug is inserted, a battery-swapping type in which a battery mounted on top of the vehicle is swapped at a swapping station, and a wireless type in which the battery is wirelessly charged through self-induction at a charging facility installed on the road. Vehicles of each charging type have different advantages and disadvantages. The performance, charging type, battery capacity, and operating environment of electric buses are mutually related parameters that must be considered when introducing such vehicles. Therefore, the optimal charging type must be selected according to the operating environment to enable the widespread use of electric buses. As such, this report proposes the optimal charging type according to the operating environment of public-sector electric vehicles.

This paper presents a novel real time control strategy on four-wheel independent steering system for electric vehicle with stepper motors using neural networks combined with fuzzy logic. The control of the four wheels is based on a variation of Hopfield Neural Network (VHNN) method, in which the input is the error of each steering motor and the output is processed by a hyperbolic tangent function (HTF) feeding the fuzzy logic controller (FLC), which ultimately drives the stepper motor. The whole system is made up of the four aforementioned blocks where they work in sync and inseparable from each other with the common goal of driving all the steering stepper motors at the same time. Simulation results demonstrate that the proposed control method has strong robustness and practicability under different angles and speeds.

Addressing the pressing challenge of global warming, reducing greenhouse gas emissions in the transportation sector is a critical imperative. Battery and fuel-cell electric vehicles have emerged as promising solutions for curbing emissions in this sector. In this study, we conducted a comprehensive life cycle assessment (LCA) for typical passenger vehicles, heavy duty trucks and city buses using either proton-exchange membrane fuel cells or Li-ion batteries with different cell chemistries. To ensure accuracy, we supplemented existing studies with data from the literature, particularly for the recycling phase, as database limitations were encountered. Our results highlight that fuel cell and battery systems exhibit large emissions in the production phase. Recycling can significantly offset some of these emissions, but a comparison of the technologies examined revealed considerable differences. Overall, battery electric vehicles consistently outperform fuel cell electric vehicles regarding absolute greenhouse gas emissions. Hence, we recommend prioritizing battery electric over fuel cell vehicles. However, deploying fuel cell electric vehicles could become attractive in a hydrogen economy scenario where other factors, e. g. the conversion and storage of surplus renewable electricity via electrolysis, become important.

The problems of operating range and costs are the two most critical bottlenecks restricting the extensive application of electric vehicles at home and abroad. There are also some prominent problems in China's electric vehicles, such as slow improvement of electric vehicle's operating range, difficulty in charging, slow charging, low utilization efficiency of charging resources, and high battery cost for electric vehicles, which lead to poor competitiveness of electric vehicles compared with traditional internal combustion engine (I.C.E.) vehicles. This paper analyzes the key factors restricting the development and popularization of electric vehicles in China from the aspects of strategic policy, sales situation and self problems. Through summarizing the experience and lessons of French standardization development strategy and electric vehicle development mode, this paper puts forward the hypothesis leading the development of electric vehicles through standardization to enhance their competitiveness, gives the specific suggestions, and briefly analyzes the feasibility from the aspects of product situation. The research content of this paper provides a certain basis and ideas for the future research work.

This work simulates the performance of lithium batteries for electric vehicles under different charge and discharge rates. The simulation is based on similarity factors for power, voltage and current, reproducing the real operation conditions of an electric vehicle at the model scale. Most current driving modes have been analysed corresponding to discharge rates from 0.1C to 0.37C. The simulation has also been applied to determine charging time using charge power in real conditions, from 6.1 kW to 18.3 kW (0.1 C to 0.3C). Driving conditions are obtained using equations for vehicle motion including all forces. Tests have been run under two configurations, continuous and alternate current circuits, to reproduce the two types of engines that electric vehicles use. The simulation shows very good agreement in charge and discharge processes, average deviation of 3% related to real conditions, and 1.6% between them, which proves the validity of the simulation process.

Air conditioning system of electric vehicles has new change as the internal combustion engine is being replaced with electrified AC motor. With large amount of batteries installed at the bottom of frame, the conventional compressor which is belt-driven can be removed and another AC motor can play the role for air conditioning in electric vehicles. From this change, the system efficiency would be improved since it is possible to control the electrified compressor independently from traction system in contrast with the belt-driven compressor. As a result, by applying the electrified compressor for air conditioning system, the whole system can achieve better efficiency and longer driving distance, which is most important in electric vehicles. In this paper, 3-phase interior permanent magnet synchronous motor (IPMSM) was designed using lumped-parameter model and finite element method.

Under the goal of carbon peak and carbon neutrality, the carbon emission reduction of the automobile industry has attracted more and more attention in recent years. Electric vehicle has the dual attributes of power load and energy storage unit. With the increase of the number of electric vehicles, reducing carbon emissions through the collaborative interaction between electric vehicle and power network will become an important way to control carbon emissions in the automotive field. In this study, an optimization model of emission reduction benefits based on integrated development of electric vehicle and power grid is proposed, which explores the best technical way of synergy between power grid and electric vehicle, achieves the best carbon reduction effect and provides a model basis for large-scale demonstration application. Numerical simulations based on the real case in Beijing are conducted to validate the effectiveness of the proposed method.

An effective battery management system (BMS) is indispensable for any lithium-ion battery (LIB) powered systems such as electric vehicles (EVs) and stationary grid-tied energy storage systems. Massive wire harness, scalability issue, physical failure of wiring, and high implementation cost and weight are some of the major issues in conventional wired-BMS. One of the promising solutions researchers have come up with is the wireless BMS (WBMS) architecture. Despite research and development on WBMS got momentum more than a decade ago, it is still in a preliminary stage. Significant further upgradation is still required towards developing an industry-ready WBMS, especially for high-power LIB packs. Therefore, an in-depth survey exclusively on WBMS architectures is presented in this article. The aim is to provide a summary of the existing developments as well as to present an informative guide to the research community for future development by highlighting the issues, emerging trends, and challenges. In-depth analysis of the existing WBMS topologies will not only help the researchers to understand the existing challenges and future research scopes clearly while at the same time enthuse them to focus their research inclination in the domain of WBMS.

The article presents a method of generating Key Performance Indicators related to electric motor energy efficiency on the basis of Big Data gathered and processed in frequency converter. The authors proved that using the proposed solution it is possible to specify the relation between the control mode of an electric drive and the control quality-energy consumption ratio in the start-up phase as well as in the steady operation with various mechanical loads. The tests were carried out on a stand equipped with two electric motors (one driving, the other used to apply the load by adjusting the parameters of the built-in brake). The measurements were made in two load cases, for motor control modes available in industrially applied frequency converters (scalar V/f, vector Voltage Flux Control without encoder, vector Voltage Flux Control with encoder, vector Current Flux Control and Vector Current Flux Control with torque control). During the experiments values of current intensities (active and output), the actual frequency value, IxT utilization factor, relative torque and the current rotational speed were measured and processed. Based on the data the level of the energy efficiency was determined for various control modes.

Two-wheeler vehicles are the most significant mode of transportation for Kenyans in both rural and urban regions thereby contributing to local air pollution, and greenhouse gas emissions (GHG). The transition to electric two-wheeler vehicles can make a significant contribution to reducing GHG and improving the socio-economic lives of people living in rural Kenya. Re-newable energy systems can considerably contribute to the charging of electric two-wheeled vehicles, thus leading to the reduction of carbon emissions and the expansion of renewable energy penetration in rural Kenya. Therefore, this paper focuses on integrating and modelling electric two-wheeled vehicles (e-bikes) into an off-grid photovoltaic Water-Energy Hub located in the Lake Victoria Region of Western Kenya using the Conventional and Renewable Energy Opti-mization (CARNOT) Toolbox in MATLAB / Simulink. Electricity demand data obtained from the Water-Energy Hub was investigated and analysed. Potential solar energy surplus was identified and electric two-wheeler vehicles were integrated based on the surplus. A field measurement investigation on the energy consumption of the electric two-wheeler vehicles based on the rider’s driving behaviour was also carried. The annual electricity demand of 27,267 kWh, photovoltaic (PV) electricity production of 37,785 kWh with an electricity deficit of 370 kWh were obtained from the simulation results. To reduce the electricity deficit, a load optimisation algorithm was de-veloped to optimally integrate the electric 2-wheeler vehicle into the Water-Energy Hub. It was found that using the load optimisation algorithm, the annual electricity deficit was reduced to 1 kWh and the annual electricity demand was increased by 11% (30,767 kWh) which is enough to charge 4 additional electric two-wheeler batteries daily.

End-of-life electric vehicle (EV) batteries can be reused to reduce their environmental impact and economic costs. However, the growth of a second-life market is limited by the lack of information on the characteristics and performance of these batteries. As the volume of end-of-life EVs may exceed the amount of batteries needed for stationary applications, investigating the possibility of repurposing them in mobile applications is also necessary. This article presents an experimental test that can be used to collect the data necessary to fill a battery passport. The proposed procedure can facilitate the decision making process regarding the suitability of a battery for reuse at the end of its first life. Once the battery passport has been completed, the performance and characteristics of the battery are compared with the requirements of several mobile applications. Mobile charging stations and forklift trucks were identified as relevant applications for the reuse of high capacity prismatic cells. Finally, a definition of a state of health (SoH) is proposed to track the suitability of the battery during use in the second life application considering not only energy but also power and efficiency of the battery. This SoH shows that even taking into account accelerated ageing data, a repurposed battery can have an extended life of 11 years at 25~°C. It has also been shown that energy fade is the most limiting performance for lifetime and that cell-to-cell variation should be tracked as it has been shown to have a significant impact on battery life.

The meticulously engineered powertrain mounting system of hybrid-electric vehicles plays a critical role in minimizing vehicle vibrations and noise, thereby enhancing the longevity of vital powertrain components. However, developing and designing such a system demands substantial time and financial investments due to intricate analysis and modeling requirements. To tackle this challenge, this study integrates data-mining technology into the design and optimization processes of the powertrain mount system. The research focuses on the powertrain mounting system of a transverse four-cylinder hybrid-electric vehicle, employing the CRISP-DM (Cross-Industry Standard Process for Data Mining) methodology to establish a data-mining prediction model for mounting stiffness. This model utilizes three data mining algorithms—Multi-SVR, MRTs, and MLPR—assessing their predictive accuracy concerning mounting system stiffness estimation. A comparative analysis reveals that the MRTs algorithm outperforms others as the most effective prediction model. The proposed predictive model elucidates the quantifiable correlation between vibration isolation performance and installation stiffness, overcoming complexities associated with traditional modeling approaches. Applying this model in powertrain mounting system design showcases the efficacy of the CRISP-DM-based approach, significantly enhancing design efficiency without compromising prediction accuracy.

Battery-powered electric vehicles (EVs) have emerged as an environmentally friendly and efficient alternative to traditional internal combustion engine vehicles, while their single-charge driving distances under cold conditions are significantly limited due to the high energy consumption of heating systems. Heat pumps can provide an effective heating solution for EVs, but their coefficient of performance (COP) is hampered by heat transfer deterioration due to frost accumulation. This study proposes a solution to this issue by introducing a microchannel heat exchanger (MHE) with superhydrophobic surface treatment (SHST) as a heat pump evaporator. A computational-fluid-dynamics MHE model and a dynamic heat pump model are developed and rigorously validated to examine the detrimental impact of frost accumulation on heat transfer, airflow resistance, and heat pump performance. When the frost layer thickness is 0.8 mm at a given air-side velocity of 1.0 m/s, the air-side heat transfer coefficient can be reduced by about 75%, and the air-side pressure drop sharply increases by 28.4 times. As frost thickness increases from 0 to 0.8 mm, the heating effect drops from 3.97 to 1.82 kW, and the system COP declines from 3.17 to 2.30. Experimental results show that the frost thickness of the MHE with SHST reaches approximately 0.4 mm after 30 minutes, compared to that of 0.8 mm of the MHE without SHST, illustrating the defrosting capability of the superhydrophobic coating. The study concludes by comparing the performance of various heating methods in EVs to highlight the advantages of SHST technology. As compared to traditional heat pumps, the power consumption of the proposed system is reduced by 48.7% due to the defrosting capability of the SHST. Moreover, the single-charge driving distance is extended to 327.27 km, an improvement of 8.99% over the heat pump without SHST.

The main objective of this paper is to develop a readiness index model that can serve as an analytical tool for exploring the achievements of electrification of transportation systems. We have applied this readiness index model to evaluate the readiness positioning of China, Norway, and Sweden to-wards transport electrification. We have chosen these three countries as they represent diversity among countries that are in the process of adopting electric transport system solutions. Our developed readiness index model has four key dimensions, technological readiness, political readiness, societal readiness, and economic readiness. The embeddedness of all four dimensions in one model provides a multi-perspective way of analyzing and evaluating the readiness levels of countries moving towards transforming the transportation system. Therefore, we named the model a “multidimensional readiness index.” Our main conclusions are that the political processes and political decisiveness involved are the most important factors followed by the societal needs and economic ability, with the current technology available as the fourth. Without the participation of dedicated and determined political decision-makers being involved, the other three factors are challenging to obtain. Political decision-makers need to facilitate the use of economic means to support the transformation in the society and affected industries to balance the initial economic disadvantages of the electrically powered systems until they pass the cost disadvantage turning point. The development of the relevant technology is no longer a great barrier as it was at the beginning of this transformation, about 20 years ago. The technology for electrically powered transportation systems and devices is widely available now, although it is continuously evolving and being improved. Associated industries cannot be expected to initiate, finance, take the risk, and take the lead in this global societal transformation without clear and strong political support.

A self-propelled electric tea seed-planter is designed to address the lack of tea seed seeding equipment, low seeding efficiency, and poor seeding uniformity. Based on the physical characteristics of the tea seeds and the agronomic requirements of tea planting, the key structure of the planter is designed, and the structural parameters are determined. The motor and battery configurations are determined by calculating the power consumption of the entire machine. In a field experiment, the driving gear (A), ditching depth (B), and planting gear position (C) are used as test factors, and the acceptance index (AI), replay index (RI) and leakage index (LI) are used as test indexes. The test results showed that the driving speed and planting gear position significantly affect the acceptance index, replay, and leakage index, whereas the ditching depth has little effect on the performance indexes. When the driving speed was medium, ditching depth was 30 mm, and planting gear position was in the third gear, the corresponding acceptance index was 87.22%, the replay index was 8.89%, and the leakage index was 3.89%. The test prototype has a good working quality and can provide theoretical guidance for production practices.

This work aims to study and analyze a hybrid power system for electric vehicles consisting of a dual low and high-rate lithium battery block and a fuel cell. In this configuration, the high-rate lithium battery powers the electric vehicle in high power demand processes like acceleration mode or on an uphill road; the low-rate battery operates at a low output power range, servicing the auxiliary systems and low power loads and the fuel cell supplies energy at intermediate power demand conditions, normal driving mode, constant velocity, or flat and downhill terrain. The dual power system improves global efficiency since every power unit operates optimally depending on driving conditions. Power sharing optimizes the lithium battery performance and fuel cell capacity, minimizing the size and weight of each energy system and enlarging the driving range. A comparative study between different lithium battery configurations and fuel cell shows an efficiency improvement of 31.4% for the hybrid dual battery block and fuel cell operating in low, high, and intermediate output power ranges, respectively. The study bases on a simulation process recreating current driving conditions for electric cars in urban, peripheral, and intercity routes. An alternative solution consisting of a hybrid system, fuel cell and a high rate lithium battery produces a 29 % power gain.

The urgency for a shift towards cleaner and more efficient energy alternatives for power generation is underscored by the escalating demand for energy and the detrimental environmental impacts of conventional fossil fuels. In the case of automotive power, electric vehicles are being adopted in many applications, however, challenges remain such as extended charging periods and limited ranges between charges. Therefore, this research study conducts a techno-economic analysis of renewable energy technologies (including solar modules, wind turbines and piezoelectric materials) to augment the efficiency and sustainability of electric buses. The study examines the scope for these technologies to be adopted on double-decker electric buses in London in the United Kingdom. The solar modules are placed on the rooftop and sides of the bus generating 15.9 kWh/day and the wind turbine in the front bumper of the bus generates 8.3 kWh/day. However, the piezoelectric material generated only 22.6 Wh/day, rendering it an impractical inclusion in further analysis. Therefore, both the solar modules and wind turbines combined generate 24.2 kWh/day, which can increase the driving range by 16.3 km per day and this results in savings of 19.36 minutes for charging at the stations. Investing in such projects would have a positive return as the internal rate of return (IRR) and net present value (NPV) are 2.8% and £11,175 respectively. The annual revenue would be £6,712, and the greenhouse gas (GHG) reduction would be two metric tons annually. Electricity exported to the grid, the electricity export rate, and the initial investment are identified as key factors influencing power outage in a sensitivity analysis. In conclusion, this numerical modelling study paves the way for experimental validation towards implementation of renewable energy technologies on electric bus fleets.

Since the 1990’s, studies and pilot tests have been conducted to reduce traffic, accidents, and pollution due to urban freight transport (UFT). These ended up in several policies, regulations, and restrictions for UFT, such as low emission zones, delivery time windows, and vehicle size and weight restrictions. However, issues in UFT under regulatory measures still persevere. This study introduces an optimization framework for deriving an optimal combination of various types of vehicles with different capacities for vehicle replacement in UFT. This framework allows an understanding of how an urban freight company with a limited budget efficiently satisfies its freight demand within an urban area in the presence of regulatory measures by urban administrators. The introduced formulation, which is a mixed-integer linear programming, will assist the operator in choosing the best investment strategy for introducing new vehicles of certain types and sizes, for operation in different zones, into its fleet while gaining economic benefits and having a positive impact on the liveability of the urban area. Furthermore, a sensitivity analysis is performed to consider the effects of specific uncertain parameters on the total cost. The numerical results show that the share of electric vehicles in the fleet increases, and they are more competitive than diesel vehicles.

With the continuous growth of electric and electronic appliances’ usage, the waste produced with obsolete material (e-waste) has an increasing environmental impact. Also, the production of such appliances bears to increased consumption of natural resources and produces a multitude of toxic and hazardous substances, which typically are not properly treated. One of the approaches that may be adopted to reduce such problems relies on the circularization of the current linear model, commonly adopted in the EEE value chain. This includes recovering eol products and reintroducing its parts, components, or raw materials into the value chain (e.g. semiconductors, circuit boards, raw metals, etc.), thus contributing to a more sustainable value chain. In this article, we present a state-of-art review that focuses on approaches and solutions for the EEE value chain traceability, and analyses the technologies that may be beneficial for promoting and implementing the CE model in this value chain.

Disassembly is a pivotal technology to enable the circularity of electric vehicle batteries by applying circular economy strategies that extend the life cycle of their components, like remanufacturing and repurposing, or by using efficient recycling to reintegrate the gained materials in producing new battery systems. This paper aims to develop a multi-method self-configuring simulation model for investigating disassembly scenarios while considering the battery design as well as the configuration and layout of the disassembly station. We demonstrate the developed model in a case study using a battery of Mercedes-Benz and the automated disassembly station of the project DeMoBat at Fraunhofer IPA. Furthermore, we introduce two disassembly scenarios, the component-oriented and the accessibility-oriented disassembly, and compare them using the simulation model to determine several indicators, such as the frequency of tool change, the number and distribution of robot routes, the tool utilization, and the disassembly time.

With the continuous improvement and observable benefits of electric vehicles (EVs), major logistic companies are introducing more EVs into their conventional fleets. This gives rise to a new type of vehicle routing problem with mixed vehicles, where heterogeneous internal combustion vehicles (ICVs) and electric vehicles are considered in route planning. In addition, certain deliveries that are not efficient on any type of vehicles, are outsourced to third-party common carriers. In this paper, we define this problem as a mixed vehicle routing problem with common carriers (MVRPC). The objective of such problems is to minimize the transportation costs by considering routes with ICVs and EVs, the possibility of visiting recharging stations, outsourcing options, and drivers’ layover regulations. This variant of the vehicle routing problems has many practical applications, particularly in the design of long-haul transportation and last-mile delivery services. Effective MVRPC solutions play a key role in promoting the going Green image and optimally allocating resources. The problem has received limited attention in the literature likely because addressing all the needed aspects is especially challenging. To solve the large-scale problem, we develop a branch-and-cut pricing framework that relies on strong cuts and customized labeling algorithms. Numerical experiments highlight the effectiveness of our algorithm. This success can be attributed to tailored critical resources, dynamically bounded bidirectional labeling procedures, strong dominance criteria, and implementation strategies.

In this paper, an in-wheel vibration absorber for In-wheel-motor electric vehicle (IWM EV) is designed, and a comprehensive control strategy of in-wheel absorber and vehicle suspension is proposed to improve vehicle ride comfort. The proposed in-wheel vibration absorber, designed for suppressing the motor vibration, is composed of a spring and a controllable damper. The values of in-wheel spring stiffness and damper initial coefficient are determined by using the improved particle swarm optimization (IPSO) algorithm, which is carried on the typical driving condition. To deal with the negative interaction effects between vehicle suspension and in-wheel absorber, the linear quadratic regulator (LQR) algorithm is utilized to control suspension damper, and the fuzzy PID method is utilized to control in-wheel damper. Based on the four evaluation indexes including vehicle body vertical acceleration, suspension dynamic deflection, wheel dynamic load and motor wallop, the simulation results show that, the proposed LQR control of suspension effectively improves vehicle ride comfort, and the fuzzy PID control of in-wheel damper exhibits superior performance of motor vibration suppressing in comparison to conventional electric wheel.

The transport sector in Germany causes one-quarter of energy-related greenhouse gas emissions. One potential solution to reduce these emissions is the use of battery electric vehicles. Although a number of life cycle assessments have been conducted for these vehicles, the influence of a transport system wide transition has not been researched sufficiently. Therefore, we developed a method which combines life cycle assessment with an agent-based transport simulation and synthetic electric, diesel and gasoline powered vehicle models. We use the transport simulation to obtain the number of vehicles, their lifetime mileage and road-specific consumption. Subsequently we analyze the product systems’ vehicle production, use phase and End-of-Life. The results are scaled depending on the covered distance, the vehicle weight and the consumption for the whole life cycle. The results indicate that the sole transition of drive trains is insufficient to significantly lower the greenhouse gas emissions. However, sensitivity analyses demonstrate that there is a considerable potential to reduce greenhouse gas emissions with higher shares of renewable energies, a different vehicle distribution and a higher lifetime mileage. The method facilitates the assessment of the ecological impacts of the complete car based transportation in urban agglomerations and is able to analyze different transport sectors.

Electro-mechanical braking(EMB) which represents development direction of autonomous and intelligent braking plays very useful role on enhancing the braking response performance and intelligence level for mine underground electric trackless rubber-tired vehicle (ETRV). However,there is no Electro-Mechanical Brake system applied practically in coal mine UTRV until now.The accurate control of braking clamping force can determine the length and precision of braking distance of mine ETRV.In addition,because of poor working conditions in underground coal mine tunnel ,braking clamping force sensor may be easy to occur failure,which may cause vital accident.Therefore,A cascaded three-closed-loop EMB system with a positive clamping force sensor or force estimator built for ETRV is established to achieve autonomous elimination and reset of braking clearance and reliable braking force tracking ability via utilizing the electro motor rotor angle displacement and hysteresis effect of mechanical components in this EMB.The results of simulation and experiment indicate that clamping force response is faster than traditional hydraulic disk braking system and proposed force estimator presents good fault-tolerant ability when sensor is fault.This EMB can replace the current hydraulic brake system to enhance automation level of braking control for ETRVs and braking force response performance, reduce oil pollution and cost of maintenance, which is also key technology support for really precise motion control of mine autonomous driving vehicles.

Heavy Ion Beam Probing (HIBP) diagnostic is a powerful tool for electric field studies in hot dense plasma of modern day toroidal magnetic confinement devices. On the TUMAN-3M to-kamak, the HIBP have been used in regimes with improved plasma confinement to clear up the role of radial electric field in the transition to good confinement regimes. Recently, a moderni-zation of the TUMAN-3M HIBP diagnostics was performed aiming to reconfigure it for a work with a reversed plasma current direction and improvement of overall stability of the diagnostic. The results of first measurements of plasma potential in co-NBI scenario are reported and dis-cussed.

This research paper presents an enhanced economic load dispatch (ELD) approach using the Teaching-Learning-Based Optimization (TLBO) algorithm for 10 thermal units, examining the impact of Plug-in Electric Vehicles (PEVs) in different charging scenarios. The TLBO algorithm is utilized to optimize the ELD problem, considering the complexities associated with thermal units. The integration of PEVs in the load dispatch optimization is investigated, and different charging profiles and probability distributions are defined for PEVs in various scenarios, including overall charging profile, off-peak charging, peak charging, and stochastic charging. These tables allow for the modeling and analysis of PEV charging behavior and power requirements within the power system. By incorporating PEVs, additional controllable resources are introduced, enabling more effective load management and grid stability. The comparative analysis showcases the advantages of the TLBO-based ELD model with PEVs, demonstrating the potential of coordinated dispatch strategies leveraging PEV storage and controllability. This paper emphasizes the importance of integrating PEVs into the load dispatch optimization process, utilizing the TLBO algorithm, to achieve economic and reliable power system operation while considering different PEV charging scenarios.

Directional protective relaying based on amplitude comparison of traveling wave on continuous co-phase auto-transformer(AT) power transmission system was proposed. Phase-model transformation is used for decoupling transient fault signals and get aerial mode component. The forward and backward traveling wave are obtained by calculating aerial mode component, then the intrinsic mode function(IMF) components can be obtained through Variational Mode Decomposition(VMD), the module maxima are obtained through calculating the IMF components. The fault direction is determined by the ratio of fault components. If two faults relays at the ends of electric traction networks detect a fault to be in the forward direction, the fault occurred in the internal area, the protection would operate properly. The simulation tests indicate that the protection scheme is feasible, and the proposed protection method can discriminate internal faults from external faults under various fault types, and its performances are immune to fault initial angle, ground resistance, etc.

Following electrification of automotive transport, studies on the penetration of Electric Vehicles (EVs) are widespread, especially in defined contexts, e.g. cities. As major transport hubs, airports fall within contexts worth of interest. In this work, a forecast of the demand for electric mobility in an Italian international airport (Rome, Fiumicino) is presented. First, a wide review of proposed sce-narios on the penetration of EVs at international and national level and available data on local automotive transport are presented, as preliminary study for the definition of reference scenarios for the local context. Then the methodology proposed is presented and applied to the specific case study. Finally, a preliminary sizing of the required charging infrastructure is reported. The proposed approach can be considered as reference for similar studies on electrical mobility in other airport areas around the world.

Electric mobility is one of the ways to contain greenhouse gas and local pollutants emissions in urban areas. Nevertheless, the massive introduction of battery-powered electric vehicles (EVs) brings some concerns related to their energy demand. Modelling vehicle usage and charging behavior is essential for charge demand forecasting and energy consumption estimation. Therefore, it is crucial to understand how the charging decisions of EV owners are influenced by different factors, ranging from the charging infrastructure characteristics to the users’ profiles. This review intends to investigate the approaches used to investigate on charging behavior and highlight trends and differences between the results, remarking on any gaps worthy of further investigation.

The transportation sector is seeing an increased adoption rate of electric vehicles (EV), which comprise battery electric vehicles (BEV), hybrid electric vehicles (HEV) and plug-in hybrid electric vehicles (PHEV). This mode of transportation is likely to displace automobiles powered by internal combustion engines (ICE) in the nearest future, as indicated by the current trend. Each of the key EC components is home to a variety of technologies that are either currently in use or will be in the near future. Electric vehicles have the potential to have a significant impact on a variety of fields, including the economy, the energy infrastructure, and the natural environment. As a result of the production of carbon dioxide gas from the combustion of fossil fuels, transportation is the sector that is responsible for the second-highest amount of greenhouse gas emissions. Electric vehicles, often known as EVs, are getting a lot of attention as a potentially game-changing solution to this issue. It is possible for electric vehicles to produce fewer emissions of carbon dioxide (CO2) than conventional automobiles due to the fact that an electric motor serves as the vehicle's propeller rather than an internal combustion engine. EVs have the potential to become zero-emission vehicles if they are paired with renewable energy sources. This document presents an overview of the numerous types of EV drive circuits, covering their design as well as the benefits and drawbacks associated with each type. The current state of battery technology, particularly that pertaining to the batteries utilized in electronic vehicles, is discussed in this paper. This article also discusses electric motor efficiency, power density, fault tolerance, dependability, cost, and the best electric motor for EVs. Then, a thorough study of future EV implementation's obstacles and prospects is done. Charging times and battery performance are examples of technological challenges, but government regulation of EVs continues to be a substantial non-technical hurdle.

Electric field assisted combustion is an important means to improve fuel combustion efficiency. This paper conducts extensive research on flame characteristics under different forms and different application methods of electric fields, emission of soot particles and simulation status. Different flame parameter measurement methods will lead to different degrees of error, and perfect numerical simulation can make simple predictions on experimental data. Most of the current numerical simulations are in two dimensions, and it is necessary to develop a complete and accurate three-dimensional model to simulate and predict the characteristics of the flame under an electric field. The emission of soot particles is also affected by the electric field, and reasonable electric field parameters can greatly reduce the emission of soot particles. It is recommended to conduct centralized measurement of different fuels under the electric field under high pressure and temperature conditions, so as to be able to develop a wider and more accurate flame dynamics and chemical model under the electric field.

The aim of this study is to investigate transient dynamic flow characteristics of the fluid flow through 5-way electric coolant valve (PCCV : Penta-Control Coolant Valve). To achieve this goal, the present paper attempts the three-dimensional dynamic simulation of the fluid flow through the valve using a commercial CFD solver with moving mesh technique to consider flow inertia and dynamic flow in the opening and closing stages of the ball valve rotating motion. Firstly, dynamic flow characteristics and the thermal mixing inside the PCCV ball valve during the opening and closing stage was analyzed. It is found that the discrepancies between dynamic and steady state simulation is remarkable when fluxes with different levels of enthalpy and momentum flow into the PCCV leads to strong flow interference and flow inertia, while the discrepancies are relatively small at low rotation speed and weak flow interference. Then, the effect of dynamic flow characteristics of the valve on dynamic thermal mixing characteristics at two different ball valve rotational speeds and rotational directions were investigated. It was found that the dynamic flow and thermal mixing characteristics inside the PCCV are greatly affected by the rotation speed, rotation direction, and degree of flow interference between fluxes. It is helpful for the design of the better coolant control strategies and the improvement of the FCEV thermal management system.

The goal of the study presented in this article is to investigate interconnection issues of the Intelligent Electrical Networks (IENs) with the existing ones, as well as the deployment of the appropriate load forecasting demand techniques. The concept of IENs has recently emerged as a potential solution to the global energy problem, due to the more flexible dispersed production units that are involved. In the same context, additional issues, such as the reduction of production-transfer-distribution costs as well as power losses are analyzed as well, via the penetration of Renewable Energy Sources (RESs). To this end, it is necessary to use appropriate advanced infrastructure, where in combination with modern telecommunication networks will make possible the full exploitation of IENs. Moreover, to make the electricity system more efficient, to avoid voltage and frequency imbalance issues and to implement optimal production and consumption planning, the Electric Load Forecast (ELF) is a vital process and plays a key role in the planning as well as in the management of electricity systems. Therefore, recent state of the art approaches in ELF methods are discussed as well.

The paper proposes a methodological way to compensate the imbalance between energy generation and consumption using the battery block of electric vehicles as energy reservoir through the well-known Vehicle to Grid system (V2G). The method is based on a simulation process developed by the authors that take into consideration the daily fluctuations of energy consumption as well as the power level generated by an energy source, either conventional, renewable or hybrid. The study shows that for very large electric vehicle fleet the system renders non-viable, since the remaining energy in the battery block to let the electric vehicle usable for running during daytime avoids to compensating for the energy grid imbalance, only allowing to cover a percentage of the energy imbalance, which the proposed methodology may optimize. The analysis of the proposed methodology also shows the viability of the system when being applied to a small fleet of electric vehicles, not only compensating for the energy imbalance but also preserving the required energy in the battery of the electric vehicle to make it run. The method allows predicting the optimum size of electric vehicle battery, which depends on the energy generation level, coverage factor of the energy imbalance and size of the electric vehicle fleet.

This article presents a novel approach to understanding the influence of electric Energy on space-time curvature. EFE actual calculations refer solely to gravitational charges. In this article, I expand them to include the electric charge with calculations carried specifically for electric charges, with exciting results. The article leverages the universal consistency of physical laws, applying the known effects of gravitational charges on space-time curvature to electric charges. The research focuses on calculating the specific impact of electric charges on space-time curvature, rooted in the principle that space-time curvature is omnipresent. The findings reveal that space-time curvature's alteration due to an electric charge is influenced by various factors, including the charge's location, magnitude, mass, density, associated electric field, and its motion through space-time. Notably, the conversion factor for electric charges differs from the conversion factor for gravitational charges. These insights significantly enhance our understanding of electromagnetism and general relativity, paving the way for a more profound comprehension of electric charges.

This paper provides a proof of concept for a linear electric generator that can be used to harvest energy from various sources of linear motion, such as vibrations, free-piston engines and wave energy. The generator can be used to power small electronic devices, such as sensors, or charge household batteries. Literature was reviewed to develop an understanding about the applications, control methods, excitation methods and mechanics of rotating and linear electric machines. A bidirectional, two-sided linear machine was designed with two stator cores and a single mover core. The stator windings and mover winding can be independently excited, allowing for three modes: no mover excitation, DC excited mover, and AC excited mover. Simulations results showed that the magnetic flux generated by DC excited stator cores were concentrated in the centre of the mover core. The use of two stator cores eliminates lateral flux in the mover core when it is not excited, minimising attraction and repulsion forces. Parametric analysis showed that flux cutting occurred in all operation modes, verifying that the generator will produce power when operating. Hardware tests produced an output current when the machine is electrically and mechanically excited, verifying the proposed design.

The state-of-the-art smart city has been calling for an economic but efficient energy management over large-scale network, especially for the electric power system. It is a critical issue to monitor, analyze and control electric loads of all users in system. In this paper, we employ the popular computer vision techniques of AI to design a non-intrusive load monitoring method for smart electric energy management. First of all, we utilize both signal transforms (including wavelet transform and discrete Fourier transform) and Gramian Angular Field (GAF) methods to map one-dimensional current signals onto two-dimensional color feature images. Second, we propose to recognize all electric loads from color feature images using a deep neural network with multi-scale feature extraction and attention mechanism. Third, we design our method as a cloud-based, non-intrusive monitoring of all users, thereby saving energy cost during electric power system control. Experimental results on both public and our private datasets have demonstrated our method achieves superior performances than its peers, and thus supports efficient energy management over large-scale Internet of Things.

This study conducted experiments to optimize the electro-dewatering of sludge using a dynamic model calculation method and the Wild Horse optimizer. Specifically, we explored two factors that might influence dewatering: the composition of the electrode materials and the strength of the electrical field. Compared to other electrodes commonly used in electro-dewatering—such as RuO2/Ir2O3-Ti, graphite, Ir2O3/Ta2O5-Ti, and Ti—the Electro-kinetic Geosynthetics (EKG) electrode exhibited superior performance. This was determined by considering both energy consumption and model establishment. Our findings also identified electric-field strength as a crucial factor determining the final moisture content. As the electrical intensity increased, the dewatering effect improved, aligning with our model calculations. However, we observed a steep increase in energy consumption per kilogram of filtrate when the electric-field strength exceeded a certain threshold. To optimize the energy consumption of the dehydration process, we constructed a multi-factor model. The simulation results from this model confirmed that electric-field intensity is the primary factor affecting dehydration. It was established that 10 V/cm is a critical threshold for the process.

The olfactory system is capable of distinguishing individual odorants from among a virtually unlimited number. Fish, for example, detect changes in the electric field environment induced by prey and other sources. Floral electric fields exhibit variations in pattern and structure, which can be discriminated by bumblebees. We have constructed an electric field sensor, which, in the course of focussing on achieving maximum sensitivity and consistency, ultimately resembles features of the insect sensorium. A “fingerprint” 3D plot ( time, frequency range, voltage amplitude), representing the emitted electric field profile, is presented for each of a variety of odorants and other chemicals. The substance-specific electric-field emission and identification is not impeded by containers or barriers or distance.

In this research, the concept of the instability of tension in Microgrid still becomes the focus of study and purpose. Scrutinously, First-Swing Instability occurs in the system in noted changes with properties of making the system unstable or restore to a state of stability. The latter calls itself as a phenomenon of re-synchronization. Allied to aspects of system instability, it is evident that by connecting fast electric chargers for battery-electric vehicles to the distribution system from microgrids, they increase the necessary basic electrical charges and reduce the stability of the electrical energy system. Transient electrical currents have the characteristic of severely impacting microgrids not prepared in connected states or island of the main system. The occurrences of the electromagnetic incompatibility of the inrush current, due to their unpredictability and intermittent characteristic, have complex identification studies. With the elevation of electricity demand by battery-electric vehicle chargers, concerns about the effects of the integration of the electricity grid increase proportionally. The research described in this article emphasizes the influence of fast chargers’ initialization on the power variation related to the re-synchronization phenomenon and its mitigation of the stability of electricity microgrid. An optimization algorithm based on particle swarm optimization (PSO) implements the development of virtual impedances. The PSO optimization algorithm analyzes all possible operating points and aims to maximize the stability index of microgrid, maintaining reactive energy incompatibilities at the minimum level supported. The fractional objective function facilitates the service to these goals simultaneously. The optimization algorithm is implemented in a case study and the corresponding virtual impedance is incorporated into the microgrid. Voltage levels are verified as a condition in the optimization process, comparing system effectiveness.

The development of electric aircrafts is becoming an important technology for achieving the goals set by the European Commission for the reduction of gases emissions by 2050 in the aeronautical transportation system. However, there is a gap between the values of specific power in commercial electric machines and the ones required for aeronautical applications. Therefore, the search for alternative materials and non-conventional designs is mandatory. One emergent solution is using superconducting machines and systems to overcome the current limits of conventional electrical machines. This work reviews the new hybrid and all-electric aircraft tendencies, complementing it with recent research on the design and development of high specific power superconducting machines. This includes the main topologies for hybrid and all-electric aircraft, with an overview of the ongoing worldwide projects of these types of aircrafts, systematizing the main characteristics of their propulsion systems. It also includes the research on superconducting machines for the purpose of high specific power, considering the impact on the redesign of aircraft systems in the electrical, cooling, and fuel source sense.

This article provides a comprehensive exploration of the electric vehicle (EV) business, investigating its current state, market dynamics, and pivotal role in sustainable transportation. It delves into factors driving EV adoption, challenges faced by the industry, and the landscape of key players. The discussion extends to investments, infrastructure development, consumer trends, and the technological innovations shaping the future. The article concludes with insights into the anticipated growth and transformative impact of EVs, emphasizing their significance in fostering a cleaner, more sustainable future for global transportation.

Zero-emission trucks for regional and long haul missions are an option for fossil-free freight. The viability of such powertrains and system solutions was studied conceptually in project ESCALATE for trucks with GVW of 40 tonnes and beyond through various prime mover combinations. The study covers battery and fuel cell power sources with different degrees of battery electric as well as H2 and fuel cell operation. As a design basis, two different missions with a single-charge/H2 refill were analysed. The first mission was the VECTO long haul profile repeated up to 750 km, whereas the second was a real 520 km on-road mission in Finland. Based on the simulated energy consumption on the driving cycle, on-board energy demand was estimated, and the initial single-charge operational scenarios were analysed with five different power source topologies. The traction motors of the tractor were dimensioned so that a secondary mission of GVW up to 76 tons on a shorter route can be operated. Based on the powertrain and vehicle model, various infrastructure options for charging and H2 refuelling strategy as well as various operative scenarios with indicative total cost of ownership (TCO) were analysed.

The present study reports a critical review of NIO's business model, considering the evolving landscape of the electric vehicle market and servicing. The objective of this study is to develop a comprehensive framework that facilitates the identification of key elements characterizing a company's business model and highlights ongoing transformations, crucial for adaptation and survival in a rapidly changing environmental context. Focusing on the case study of NIO, a relatively young Chinese original equipment manufacturer (OEM) specializing in high-tech electric cars, the research delves into the challenging scenario of the Chinese electric vehicle market, which has recently faced a bubble in 2023. The market proliferation, supply chain disruptions, and price wars triggered by Tesla have resulted in a survival struggle for numerous automotive startups, leaving larger companies with increasing market shares. Despite facing adversities, NIO managed to secure a promising segment, catering to premium-range battery electric vehicles (BEVs), establishing a competitive advantage through differentiation. By pursuing ambitious investments, the company aims to create economies of scope and achieve cost leadership, venturing into new market sectors and vertically integrating the production chain. Given NIO's agility in adapting to market conditions, aggressive entry into new segments, and a strategic vision for the future, it serves as an excellent candidate for testing and validating the proposed framework. The research sheds light on NIO's trajectory and offers insights into its potential for sustained growth in the dynamic electric vehicle market.

As we all know, contemporary electromagnetic theory is based on the macroscopic electromagnetic theory established by the 19th century. Because of the lack of microscopic cognition in that era, various electromagnetic phenomena could only be explained and described at the macro level, and their origins could not be explained at the micro level. And because of the microscopic understanding of atomic physics in the 20th century, new progress has been made. Considering that it is now the 21st century, this paper attempts to establish a new theory of microscopic interpretation of classical electromagnetic theory based on the new cognition of atomic physics in the 20th century. Starting from the general assumption, the current will be interpreted as the momentum flow produced by the directed collision between electrons; the charge will be interpreted as a form of expression of electron motion; the voltage is interpreted as the potential difference (energy level difference) of the electron orbit. In the end, this paper successfully developed a new microscopic electromagnetic theory by introducing microscopic atomic physics and rigid body mechanics models to Maxwell's macroscopic electromagnetic theory.