The vibration signal of the engine contains strong background noise and many kinds of modulating components, which is difficult to diagnose. Variational mode decomposition (VMD) is a recently introduced adaptive signal decomposition algorithm with a solid theoretical foundation and good noise robustness compared with empirical mode decomposition (EMD). VMD can effectively avoid endpoint effect and modal aliasing. However, VMD cannot effectively eliminate the random noise in the signal, so the random decrement technique is introduced to solve the problem. Based on the crankshaft bearing fault simulation experiment, the four kinds of wear state vibration signals are decomposed by VMD, and the modal components with smaller permutation entropy are selected as fault components. Then the fault component is processed by the random decrement technique, and the Hilbert envelope spectrum of the fault component is obtained. Compared with the fault feature extraction method based on EMD and EEMD, the feature extraction results of the proposed method are better than those of the above two methods. The simulation analysis and the simulation test of the crankshaft bearing fault verify the effectiveness of the proposed method.

Due to the global warming and dynamic changes in pathogenic virulence, leaf rust caused by Puccinia triticina has greatly expanded its epidermic region and become a severe threat to global wheat production. Genetic bases of wheat resistance to leaf rust mainly relies on the leaf rust resistance (Lr) gene or quantitative trait locus (QLr). Although these genetic loci have been insensitively studied during the last two decades, an updated overview of Lr/QLr in a genome-wide level is urgently needed. This review summarized recent progresses in genetic studies of wheat resistance to leaf rust. Wheat germplasms with great potentials in genetic improvement of resistance to leaf rust were highlighted. Key information about the genetic loci carrying Lr/QLr were summarized. A genome-wide chromosome distribution map for all the Lr/QLr was generated based on the released wheat reference genome. In conclusion, this review has provided valuable sources for both wheat breeders and researchers to understand the genetics of resistance to leaf rust in wheat.

Secretory and membrane proteins are vital for cell activities, including intra- and intercellular communication. Therefore, protein quality control in the endoplasmic reticulum (ER) is an essential and crucial process for eukaryotic cells. Endoplasmic reticulum-associated degradation (ERAD) targets misfolded proteins during the protein maturation process in the ER and leads to their disposal. This process maintains the ER productive function and prevents misfolded protein stress (i.e., ER stress). The ERAD-stimulating factor ER degradation-enhancing α mannosidase-like 1 protein (EDEM1) acts on misfolded proteins to accelerate ERAD, thereby maintaining the productivity of the ER. However, the detail mechanism underlying the function of EDEM1 in ERAD is not completely understood due to lack of established physiological substrate proteins. In this study, we attempted to identify substrate proteins for EDEM1 using siRNA. The matrix component thrombospondin-1 (TSP1) and epidermal growth factor receptor (EGFR) were identified as candidate targets of EDEM1. Their protein maturation status and cellular localization were markedly affected by knockdown of EDEM1. We also showed that EDEM1 physically associates with EGFR and enhances EGFR degradation via ERAD. Our data highlight the physiological role of EDEM1 in maintaining specific target proteins and provide a potential approach to the regulation of expression of clinically important proteins.

Programmed cell death protein 1 (PD-1) is a biomarker on the surface of cells that has a role in promoting self-tolerance by suppressing the inflammatory activity of T cells. In this work, one peptide of PD-1 was used as the template in molecular imprinting. The magnetic peptide-imprinted poly(ethylene-co-vinyl alcohol) composite nanoparticles (MPIP NPs) were characterized by dynamic light scattering (DLS), high-performance liquid chromatography (HPLC), Brunauer-Emmett-Teller (BET) analysis and superconducting quantum interference device (SQUID) analysis. Natural killer-92 (NK-92) cells were added to these composite nanoparticles and then incubated with human hepatoma (HepG2) cells. The viability and apoptosis pathway of HepG2 were then studied using cell counting kit-8 (CCK8) and the quantitative real-time polymerase chain reaction (qRT-PCR), respectively. These nanoparticles were found significantly enhance the activity of natural killer cells toward HepG2 cells by increasing expression of NK-kB, caspase 8 and especially caspase 3.

Initial attempts to develop monoclonal antibodies as therapeutics to resolve influenza infections focused mainly on searching for antibodies with the potential to neutralise the virus in vitro with classical haemagglutination inhibition and micro-neutralisation assays. This led to the identification of many antibodies that bind to the head domain of haemagglutinin (HA) which generally have potent neutralisation capabilities that block viral entry or viral membrane fusion. However, this class of antibodies has a narrow breadth of protection in that they are usually strain specific. This led to the emphasis on stalk targeting antibodies which are able to bind a broad range of viral targets that span across different influenza subtypes. Recently, a third class of antibodies targeting the vestigial esterase (VE) domain have been characterised. In this review, we describe the key features of neutralising VE targeting antibodies and compare them with head and stalk class antibodies.

Masquelet induced-membrane technique for the treatment of segmental bone defects includes a two-stage surgical procedure, and polymethylmethacrylate (PMMA) plays a major role in the treatment. However, the PMMA spacer must be surgically removed. Here, we investigated the potential of poly (lactic-co-glycolic acid) (PLGA) nanofibers, a biodegradable material to replace PMMA spacer, allowing the bioactive membrane to be induced, and the spacer to degrade without the additional surgery on a rabbit femoral segmental bone defect model. PLGA nanofibers were shown to degrade completely six weeks after implantation in the investigated animals, and a thick membrane was found to circumferentially fold around the segmental bone defects. Results from image studies demonstrated that, in the group without bone graft, all studied femurs exhibited either nonunion or considerable malunion. In contrast, the femurs in the bone graft group had a high union rate without considerable deformities. Histological examinations suggested that the membranous tissue in this group was rich in small blood vessels and the expression of BMP2 and VEGF increased. Our results demonstrate that the biodegradable PLGA nanofibers may be useful for replacing the PMMA spacer as the bioactive-membrane inducer, facilitating the process of healing and removing the need for repeated surgeries.

This research addresses the formidable challenge of achieving precise trajectory tracking for autonomous vehicle formations in uncertain environments. It introduces an adaptive control system tailored for autonomous vehicles, with a primary focus on ensuring prescribed performance in trajectory tracking within a leader-follower formation paradigm. The system incorporates a guidance law that allows the leader vehicle to dynamically adjust desired yaw angles and speeds for follower vehicles based on the established reference trajectory, enhancing tracking accuracy and responsiveness to environmental changes. To address practical external disturbances, the study utilizes Radial Basis Function Neural Networks (RBFNN) in conjunction with second-order filters for error approximation. This approach is further strengthened by a carefully formulated adaptive law. The innovative integration of a barrier Lyapunov function with the backstepping method significantly enhances the system’s adaptability and robustness, ensuring trajectory tracking performance meets predetermined standards. Simulation results illustrate the control system’s adept handling of various external disturbances, consistently maintaining trajectory tracking errors within predefined limits. This underscores the system’s potential to markedly enhance the operational reliability and efficiency of autonomous vehicle formations in unpredictable environmental conditions.

The microsporidium Nosema ceranae is a high prevalent parasite of the European honey bee (Apis mellifera). This parasite is spreading across the world into its novel host. The developmental process and some mechanisms of N. ceranae infected honey bees has been studied thoroughly, however, few studies have been carried out in the mechanism of gene expression in N. ceranae during infection process. We therefore performed suppressive subtractive hybridization (SSH) approach to investigate the candidate genes of N. ceranae during its infection process. Each 96 clones of infected (forward) and non-infected (reverse) library were dipped onto the membrane for hybridization. A total of 118 differentially expressed sequence tags (ESTs) had been sequenced. For the host responses, 20% of ESTs (13 ESTs, 10 genes and 1 non-coding RNA) from forward library and 83% of ESTs (44 ESTs, 28 genes) from reverse library were identified as differentially expressed genes (DEGs) of the hosts. High percentage of DEGs involved in catalytic activity and metabolic processes, revealed the host gene expression change after N. ceranae infection might lead to the unbalance of physiological mechanism. Among the ESTs from forward library, 75.4% ESTs (49 ESTs belonged to 24 genes) were identified as N. ceranae genes. Of 24 N. ceranae genes, nine DEGs were subjected to real-time quantitative reverse transcription PCR (real-time qRT-PCR) for validation. The results indicated that these genes showed highly up-regulated during N. ceranae infection. Among nine N. ceranae genes, one N. ceranae gene (AAJ76_1600052943) showed the highest expression level after infection. These identified differentially expressed genes from this SSH could provide information about the pathological effects of N. ceranae. Validation of nine up-regulated N. ceranae genes revealed highly potential for the detection of early nosemosis in the field and provide insight for further applications.

In the process of construction and operation of the pumping station, a large number of axial flow pumps pose a threat to the survival of fish in the natural environment. Through experiments, the survival conditions of many kinds of fish in extreme positive and negative pressure environment are explored, and -40 kPa is established as the low pressure damage threshold, which is used as a reference to analyze the probability of fish damage caused by pumps. The immersion boundary-lattice Boltzmann numerical method (LES-IB-LBM) based on large eddy simulation is used to optimize the parameters of the prototype runner of axial flow pump. A new type of runner with leading edge thickness of 11.4mm and blade cutting angle of 18 ° is optimized. This kind of runner has both hydraulic performance and fish-passing ability. The runner of the fish-friendly axial flow pump effectively guides the fish into the low risk area and reduces the risk of friction, shear and impact damage to the fish. the total impact mortality ratio of the runner of the axial flow pump before and after optimization is close to 7:1. The pressure damage analysis shows that the lowest negative pressure of the fish is -59.2 kPa, which is higher than -64.5 kPa of the prototype pump, and the highest positive pressure of the body surface is 11.8 kPa, which is lower than the 43.8 kPa of the prototype pump. Shear damage analysis shows that the fish will not be damaged by shear in the prototype pump and fish-friendly pump.

The performance of bearings plays a pivotal role in determining the dependability and security of rotating machinery. In intricate systems demanding exceptional reliability and safety, the ability to accurately forecast fault occurrences during operation holds profound significance. Such predictions serve as invaluable guides for crafting well-considered reliability strategies and executing maintenance practices aimed at enhancing reliability. In order to ensure the reliability of bearing operation, this article investigates the application of three advanced techniques—Maximum Correlation Kurtosis Deconvolution (MCKD), Multi-Scale Permutation Entropy (MPE), and Long Short-Term Memory (LSTM) recurrent neural networks—for the prediction of the remaining useful life (RUL) of rolling bearings. Each technique's principles, methodologies, and applications are comprehensively reviewed, offering insights into their respective strengths and limitations. Case studies and experimental evaluations are presented to assess their performance in RUL prediction. Findings reveal that MCKD enhances fault signatures, MPE captures complexity, and LSTM excels in modeling temporal patterns. The root mean square error of the prediction results is 0.007. The fusion of these techniques offers a comprehensive approach to RUL prediction, leveraging their unique attributes for more accurate and reliable predictions.

Over the past two decades, covalent organic frameworks (COFs) have become the most widely studied porous crystalline materials. Its specific physical and chemical properties are determined by the arrangement of atoms (crystal structure). Therefore, the determination of its structure is arguably the most important characterization step for COFs. Although single crystal X-ray diffraction (SCXRD) is the most widely used method for structure determination, the size of COF crystals is too small, or their crystal quality is so poor that confirmation of their structure is limited to lattice fringes by transmission electron microscopy (TEM). At present, many 2D-COFs have clear PXRD patterns, but not all 2D-COFs can obtain specific lattice fringes. This severely hinders the development of the COF field. Here, we discover the lattice shrinkage behavior of COFs under electron beam irradiation by comparing the lattice fringes of 2D-COFs under different conditions. By comparing the lattice fringes of TAPT-TFPT COF at room temperature and under liquid nitrogen freezing conditions, we found that the lattice fringes are in good agreement with the Powder X-ray diffraction (PXRD) and theoretical values of COF (2.213 nm) under freezing conditions, however, the lattice fringe spacing is only 1.656 nm at room temperature. The discovery not only provides new insights into the TEM characterization of COFs, but also further expands the range of crystalline COF materials.

Maize, a crop of international relevance, frequently undergoes xylem embolism due to water shortage, negatively impacting growth, yield, and quality. Consequently, a refined comprehension of xylem embolism is vital for enhancing maize cultivation. Notwithstanding extensive research and the generation of analytical models for embolism mechanisms, prevalent models often disregard crop-specific hydraulic processes and the formation of embolisms via air bubbles in the xylem conduit. In this research, we present an inventive model applying pipe cavitation parameters to discern water potential and bubble formation in maize leaf xylem. The model integrates pivotal physiological traits of maize—leaf count, leaf vein count, and average leaf radius—demonstrating robust correlations. Furthermore, we constructed a percentage conductivity loss (PLC) curve based on pre-dawn leaf water potential and compared it with our model, offering interval data to observe embolisation events triggered by air bubbles. Utilizing experimental data, our novel cavitation-parameters based model effectively corresponds with observed bubble phenomena and appropriately characterizes water transport in plant xylem conduits. This method enabled us to observe the transition from bubble occurrence to cavitation embolism microscopically, which aligned with the embolism intervals provided by the model. This procedure reveals potential trends in bubble-induced embolism and deepens our knowledge of microscopic plant hydraulics and crop embolism. This work establishes a basis for understanding the generation of bubble embolisms in maize, assists in evaluating maize plant water status for efficient water supply management throughout the growth cycle, and contributes towards potential water management strategies for maize.

The near-infrared (NIR) organic dyes with strong ultrafast nonlinear optical (NLO) activities are of importance for various applications. However, such kinds of dyes are still scarce. In this work, we have compared the NLO properties of two NIR Aza-BODIPY derivatives, in which the strong electron-donating groups, namely 4-(N, N-dimethylamino) phenyl and 1-ethyl-1,2,3,4-tetrahydroquinoline groups, are connected with the cores of Aza-BODIPY. Z-Scan experimental results show that two Aza-BODIPY derivatives exhibit strong saturation absorption and large modulation depth under the excitation of femtosecond pulses at 800 nm. Under 1300 nm excitation, two derivatives exhibit strong nonlinear refraction. In addition, the Aza-BODIPY derivatives also display effective two-photon excited fluorescence emission in the wavelength range of 1200-1600 nm. Based on the experimental results, it is found that 1-ethyl-1,2,3,4-tetrahydroquinoline group can more effectively enhance the NLO properties of Aza-BODIPY derivatives compared with the 4-(N, N-dimethylamino) phenyl group, thus providing new possibilities for the design and development of NIR NLO materials.

Raman spectroscopy is a type of inelastic scattering that provides rich information about a sub-stance based on the coupling of the energy levels of their vibrational and rotational modes with incident light. It has been applied extensively in many fields. As there is an increasing need for remote detection of chemicals in planetary exploration and anti-terrorism, it is urgent to develop a compact and easily transportable fully automated remote Raman detection system for trace detection and identification of information with high-level confidence about the target’s compo-sition and conformation in real-time and for real field scenarios. Here, we present an unmanned vehicle-based remote Raman system, which includes a 266 nm air-cooling passive Q-switched nanosecond pulsed laser of high-repetition frequency, a gated ICMOS, and an unmanned vehicle. This system obtains good spectral signals from remote distances ranging from 3 m to 10 m for simulating realistic scenarios, such as aluminum plate, woodblock, paperboard, black cloth, and leaves, and even for detected amounts as low as 0.1 mg. Furthermore, a CNN-based algorithm is implemented and packaged into the recognition software to achieve fast and more accurate de-tection and identification. This prototype provides a proof-of-concept for an unmanned vehicle with accurate remote substance detection in real-time, which can be helpful for remote detection and identification of hazardous gas, explosives, their precursors, and so forth.

Idiopathic scoliosis (IS) is an unexplained dysplasia of the spine that can occur at any age, with idiopathic scoliosis making up the largest proportion of the total population worldwide, approximately 2-3%. Scoliosis is not just a cosmetic defect, but the development of the spinal deformity can lead to cardiovascular and respiratory lesions, often resulting in serious health problems. Treatment of the condition usually involves major surgery, which is both a physical and financial burden for patients. In order to clarify the aetiology of IS and provide a theoretical basis for new diagnostic and treatment methods IS, it is important to use different animal models for experiments. Zebrafish is an emerging model animal with a short reproductive cycle, minimal breeding expenses, and other beneficial traits including in vitro fertilisation, in vitro development, and embryo transparency. As a result, genetic alteration and observation are simpler than with traditional model animals. This study examines the history of animal models for IS research, focuses on the benefits and drawbacks of zebrafish as an IS model and the advances it provides to IS research, and anticipates zebrafish application prospects in IS research.

Coal permeability data are critical in the prevention and control of coal and gas outbursts in mines and are an important reservoir parameter for the development of coalbed methane. The mechanism by which permeability is affected by gas pressure is complex. We used a self-developed true triaxial seepage experimental device that collects lignite and anthracite coal samples, sets fixed axial pressure and confining pressure, and changes gas pressure by changing the orientation of the coal seam to study the influence of the gas pressure on the permeability of the coal seam under the conditions of different coal types and different bedding orientations. Coal permeability decreased rapidly and then decreased slowly and tended to be stable with the increase in gas pressure. This conforms to the power exponential fitting relationship, and the fitting degree reaches more than 99%. The permeabilities of lignite and anthracite were basically the same under various pressure conditions, indicating that the influence of coal type on coal permeability was not significant. The comparison of the two anthracite coal samples showed that the sample's permeability with a bedding plane vertical to the seepage direction was significantly lower than that of the bedding plane parallel to the seepage direction, indicating that gas seeped more easily along the bedding. The sensitivity coefficient of permeability with the change in gas pressure was calculated. The analysis showed that coal permeability was sensitive to changes in gas pressure during the low-pressure stage. When the gas pressure was greater than 0.8 MPa, the sensitivity coefficient was significantly reduced, which may be related to the slow increase in the amount of gas absorbed by the coal seam in the high-pressure stage. A theoretical calculation model of coal seam permeability considering adsorption/desorption and seepage effects was proposed and then verified with experimental results showing that the theoretical model better reflected the permeability characteristics of coal and predicted its permeability. Using the finite element simulation software COMSOL, the extraction efficiency of the coal seam gas under different gas pressure conditions was simulated. The results showed that with an increase in gas pressure, coal permeability and extraction efficiency decreased. In the low-pressure stage, the reduction in the extraction efficiency was more obvious than that in the high-pressure stage.

Two monoclonal antibodies (mAbs) against human epidermal growth factor receptor 2 (HER2), trastuzumab and pertuzumab, were clinically approved. We previously developed a highly sensitive and specific anti-HER2 mAb, H2Mab-139 (mouse IgG1, kappa). In this study, we produced a defucosylated IgG2a version of anti‑HER2 mAb (H2Mab-139-mG2a-f) to enhance ADCC-mediated antitumor activity. H2Mab-139-mG2a-f exhibits a high binding affinity in flow cytometry with the dissociation constant (KD) determined to be 3.9 × 10‑9 M and 7.7 × 10‑9 M against HER2‑overexpressed Chinese hamster ovary (CHO)-K1 (CHO/HER2) and HER2-positive BT-474 cells, respectively. Moreover, we showed that H2Mab-139-mG2a-f exerted ADCC and complement-dependent cytotoxicity against CHO/HER2 and BT-474 cells in vitro and exhibited potent antitumor activities in the xenograft models. These results indicated that H2Mab-139-mG2a-f exerts antitumor effects against HER2-positive human breast cancers and could be useful for an antibody treatment regimen for HER2-positive human cancers.

Sea surface salinity (SSS) is one of the Essential Climate Variables (ECVs) as defined by the Global Climate Observing System (GCOS). Acquiring high-quality SSS datasets with high spatial-temporal resolution is cruicial for research on the hydrological cycle and earth climate. This study assessed the quality of SSS data provided by four high-resolution ocean reanalysis products, including the Hybrid Coordinate Ocean Model (HYCOM) 1/12° global reanalysis, the The Copernicus Global 1/12° Oceanic and Sea Ice GLORYS12 Reanal-ysis, the Simple Ocean Data Assimilation (SODA) reanalysis, the ECMWF Oceanic Reanalysis System 5 (ORAS5) product and the Estimating the Circulation and Climate of the Ocean Phase II (ECCO2) reanalysis. Regional comparison in the Mediterranean Sea shows that reanalysis largely depicts the accurate spatial SSS structure away from river mouths and coastal areas but slightly underestimates the mean SSS values. Better SSS reanalysis performance is found in the Levantine Sea while larger SSS uncertainties are found in the Adriatic Sea and the Aegean Sea. The global comparison with CMEMS level-4 (L4) SSS show generally con-sistent large-scale structures. The mean ΔSSS between monthly gridded reanalysis data and in situ analyzed data is -0.1 PSU in the open seas between 40°S and 40°N with the mean Root Mean Square Deviation (RMSD) generally smaller than 0.3 PSU and the majority of correlation coefficients higher than 0.5. Comparison with collocated buoy salinity shows that reanalysis products well captures the SSS variations at the locations of tropical moored buoy arrays at weekly scale. Among all the four products, the data quality of HYCOM re-analysis SSS is highest in marginal sea, GLORYS12 has the best performance in the global ocean especially in tropical regions. Comparatively, ECCO2 has the overall worst performance to reproduce SSS states and variations by showing the largest discrepancies with CMEMS L4 SSS.

Sensory descriptive analysis was used to evaluate the aged Feng-flavored baijiu. The results indicated that there are notable differences in the samples of different ages. The samples with shorter storage times and fresh distilled Baijiu present bran flavor, and fresh green flavor. with the increase of storage time, the fragrance of honey, sweetness, flowers, and aging gradually increases. The samples of Feng-flavored baijiu were dected by Headspace solid-phase microextraction (HS-SPME) combined with comprehensive two-dimensional gas chromatography time-of-flight mass spectrometry (GC×GC–TOFMS) , in total, 496 sustances were identified in all samples, mainly containing 14 types of substances, such as esters, aldehydes etc., of which 42 substances were found in Feng-flavored baijiu for the first time. Chemometrics was used to analyze the key differential compounds. 143 differential compounds closely related to aging were preliminarily screened, and principal component analysis revealed that these samples were separated by year. 65 differential compounds were selected out by partial least squares discriminant analysis(PLS-DA). Furthermore, 43 key differential compounds were selected from the aged Feng-flavored baijiu combined with variable importance in projection and Pearson correlation coefficients. Partial least squares regression (PLSR) was used to research the correlation of sensory properties and key differential compounds, and the results indicated that most compounds were closely related to the aged Baijiu . This study afford theoretical basis and reference for flavor research of Feng-flavored baijiu.

The metro station ridership features are associated significantly with the built environment factors of the pedestrian catchment area surrounding metro stations. The existing studies have focused on the impact on total ridership at metro stations, ignoring the impact on varying patterns of metro station ridership. Therefore, the reasonable identification of metro station categories and built environment factors affecting the varying patterns of ridership in different categories of stations is very important for metro construction. In this study, we developed a data-driven framework to examine the relationship between varying patterns of metro station ridership and built environment factors in these areas. By leveraging smart card data, we extracted the dynamic characteristics of ridership and utilized hierarchical clustering and K-means clustering to identify diverse patterns of metro station ridership, and finally identified six main ridership patterns. We then developed a new built environment measurement framework and adopted multinomial logistic regression analysis to explore the association between ridership patterns and built environment factors. (1) The clustering analysis result revealed that six station types were classified based on varying patterns of passenger flow, representing distinct functional characteristics. (2) The regression analysis indicated that diversity, density, and location factors were significantly associated with most station function types, while destination accessibility was only positively associated with employment-oriented type station, and centrality was only associated with employment-oriented hybrid type station. These results could inform the coordinated development of rail transit and land use, and the renewal and enhancement of the built environment in the pedestrian catchment area surrounding metro stations.

Abstract: Because of outstanding heat resistance and processing qualities, benzoxazine resins are widely employed in a variety of applications. However, traditional benzoxazine resins still confront hurdles in today's engineering applications, such as can’t long-term service in high-temperature settings and inadequate toughness. Four alkyne-functionalized benzoxazines with phthalide side group and cyano group of varying molecular weights were produced in this study. Fourier trans-form infrared spectroscopy (FT-IR) and hydrogen nuclear magnetic resonance spectroscopy ( 1H-NMR ) were used to characterize the resin structure, and differential scanning calorimetry (DSC) was used to investigate the thermal curing kinetics at different warming rates, the apparent activation energy was 116.9 kJ/mol. In-situ FTIR was used to investigate the cure mechanism. Dynamic mechanical analysis (DMA) was used to evaluate the gelationation time of BOZ series resins at various temperatures, and the curing process was designed by combined the results of DSC. The Tg of the composites made using BOZ-1N21 as the matrix was 336°C, which was much higher than the Tg of the BP-a resin made with aniline, phenolphthalein, and formaldehyde (Tg=251°C). As a result, the resin system is expected to be employed in applications requiring high-temperature resistance and toughness.

Despite empirical findings that prosociality can prevent children and adolescents from developing psychological maladjustment, little is known about the underlying mechanisms. The goal of the present study was to examine the mediating effects of peer preference and self-perceived social competence on the associations between prosociality and psychological maladjustment (i.e., depressive symptoms and loneliness). Participants were 951 students (Mage = 11 years, 442 girls) in Grades 3~7 from Shanghai, China. They completed peer nominations of prosociality and peer preference, and self-report measures of self-perceived social competence, depressive symptoms, and loneliness. Multiple mediation analyses revealed that: (a) both peer preference and self-perceived social competence mediated the relations between prosociality and psychological maladjustment; and (b) a serial indirect pathway (i.e., prosociality  →  peer preference  →  self-perceived social competence →  psychological maladjustment) emerged when controlling for grade and gender. These findings point to potential targets in the prevention and intervention of adolescent internalizing problems.

Soil microbial fuel cells (sMFC) are a novel technique that use organic matters in soils as an alternative energy source. External resistance (ER) is a key factor influencing sMFC performance and, furthermore, alters the soil’s biological and chemical reactions. However, little information is available on how the microbial community and soil component changes in sMFC with different ER. Therefore, the effects of anodes of sMFC at different ER (2000 Ω, 1000 Ω, 200 Ω, 80 Ω and 50 Ω) were examined by measuring organic matter (OM) removal efficiency, trace elements in porewater and bacterial community structure in contaminated paddy soil. The results indicated that ER has significant effects on sMFC power production, OM removal efficiency and bacterial beta diversity. Moreover ER influences iron, arsenic and nickel concentration as well in soil porewater. In particular, greater current densities were observed at lower ER (2.4mA, 50Ω) compared to a higher ER (0.3mA, 2000Ω). The removal efficiency of OM increased with decreasing ER whereas it decreased with soil distance away from the anode. Furthermore, principal coordinate analysis (PCoA) revealed that ER may shape the bacterial communities that develop in the anode vicinity but have minimal effect on that of the bulk soil. The current study illustrates that lower ER can be used to selectively enhance the relative abundance of electrogenic bacteria and lead to high OM removal.

Edge detection is one of the key issues in the field of computer vision and remote sensing image analysis. Although many different edge-detection methods have been proposed for gray-scale, color, and multispectral images, they still face difficulties when extracting edge features from hyperspectral images (HSIs) that contain a large number of bands with very narrow gap in the spectral domain. Inspired by the clustering characteristic of the gravitation, a novel edge-detection algorithm for HSIs is presented in this paper. In the proposed method, we first construct a joint feature space by combining the spatial and spectral features. Each pixel of HSI is assumed to be a celestial object in the joint feature space, which exerts gravitational force to each of its neighboring pixel. Accordingly, each object travels in the joint feature space until it reaches a stable equilibrium. At the equilibrium, the image is smoothed and the edges are enhanced, where the edge pixels can be easily distinguished by calculating the gravitational potential energy. The proposed edge-detection method is tested on several benchmark HSIs and the obtained results were compared with those of three state-of-the-art approaches. The experimental results confirm the efficacy of the proposed method

In the most cases, invasive ductal carcinoma (IDC) of the breast is identifiable when they present with classic infiltrative growth pattern. However, subset of IDC can occur in a very sneaky way, significantly mimicking the appearance of ductal carcinoma in situ (DCIS). In this condition, it’s much easier to miss the invasive component without pulling ancillary staining when morphologic findings are extremely compatible with DCIS, especially the diagnosis of DCIS was made on the previous biopsy. Here, we reported a 55 year-old female who was noted to have microcalcification at the 11:00 o’clock of the right posterior breast on routine mammographic examination in 09/2023. Biopsy of the calcification area in 10/2023 reported high grade DCIS (ER+ PR-). Histologic examination of subsequent mastectomy specimen showed two separate DCIS-looking areas (Figure 1A-D and Figure 2). Immunohistochemical (IHC) staining showed that myoepithelial markers, smooth muscle myosin heavy chain (SMMHC), p63, CK5/6 and S100, were retained at the periphery of all the expanded acini in one area (Figure 1E-H). Unexpectedly and surprisingly, myoepithelial markers were completely lost at the periphery of part of the DCIS-looking acini in another area (Figure 3A-H), immunohistochemically compatible with the diagnosis of invasive ductal carcinoma admixed with DCIS. Knowing that invasive ductal carcinoma of the breast can present as DCIS-looking morphology, especially given the condition that the diagnosis of DCIS was rendered on the previous biopsy, will enhance awareness of pathologists to recognize DCIS-looking invasive ductal carcinoma. In turn, this will prevent misdiagnosis and under-treatment of patients with invasive ductal carcinoma of the breast.

As environmental regulations become stricter, weight- and cost-effective fiber-reinforced polymer com-posites are being considered as alternative materials in the automobile industry. Rapid impregnation of the resin into the reinforcing fibers is critical during liquid composite molding, and the optimization of resin impregnation is related to the cycle time and quality of the products. In this review, various resins capable of rapid impregnation, including thermoset and thermoplastic resins, are discussed for manu-facturing fiber-reinforced composites used in the automobile industry, along with their advantages and disadvantages. Finally, vital factors and perspectives for developing rapidly impregnated resin-based fiber-reinforced composites for automobile applications are discussed

In this paper, a sensitivity sensor of dual-core photonic crystal fiber (DC-PCF) filled with magnetic liquid is introduced and investigated by the finite element method (FEM). To regulate the energy coupling involving the two cores, the magnetic fluid is filled into the pore between the two cores. To adjust the coupling between the supermodes in the DC-PCF, the refractive index of the magnetic fluid-filled air hole may change due to the external magnetic field. This specifically created a magnetic fluid-filled DC-PCF, the magnetic fluid-filled hole is not used as the core for energy transmission, thus avoiding transmission loss. The dip wavelength and the magnetic field displayed an excellent linear connection between 80 and 260 Oe, depending on the numerical data. The detection sensitivity of the magnetic field reached 515.75 pm/Oe at a short fiber length of 482 m. The designed magnetic fluid-filled DC-PCF has high sensitivity and small volume and has great application prospects in medical and industrial field magnetic field detection.

Cadmium (Cd) is a toxic non–essential element to plants, and its accumulation in crops has significant adverse effects on human health. The cross–talk between copper (Cu) and Cd has been reported, but the molecular mechanisms remain unknown. Here, the function of wheat Cu transporter 3D (TaCOPT3D) in Cd tolerance was investigated. The TaCOPT3D transcripts significantly accumulated in wheat roots under Cd exposure. To test whether TaCOPT3D was involved in response to Cd stress, overexpressing lines with altered expression of TaCOPT3D transporters were compared to wild–type (WT) plants. The results showed that, under 20 μM Cd treatment, TaCOPT3D–overexpression lines exhibited more biomass and lower Cd accumulation in roots, shoots, and grains compared to WT plants. In addition, the TaCOPT3D–overexpression lines demonstrated less reactive oxygen species (ROS) and a greater amount of active antioxidant enzymes under Cd conditions than WT plants. Moreover, TaCOPT3D–overexpression lines highly reduced Cd accumulation under exposure to 20 μM Cu. The regulation pathway of TaCOPT3D in response to Cd stress was investigated, and transcription factor (TF) TaWRKY22, which targeted the TaCOPT3D promoter, was identified. Therefore, TaCOPT3D can serve as a candidate gene for decreasing Cd accumulation in wheat through genetic engineering.

Sedimentary microfacies division is the basis of oil and gas exploration research. The traditional sedimentary microfacies division mainly depends on human experience, which is greatly influenced by human factor and is low in efficiency. Although deep learning has its advantage in solving complex nonlinear problems, there is no effective deep learning method to solve sedimentary microfacies division so far. Therefore, this paper proposes a deep learning method based on DMC-BiLSTM for intelligent division of well-logging—sedimentary microfacies. First, the original curve is reconstructed multi-dimensionally by trend decomposition and median filtering, and spatio-temporal correlation clustering features are extracted from the reconstructed matrix by Kmeans. Then, taking reconstructed features, original curve features and clustering features as input, the prediction types of sedimentary microfacies at current depth are obtained based on BiLSTM. Experimental results show that this method can effectively classify sedimentary microfacies with its recognition efficiency reaching 96.84%.

This paper investigates the cooperative anti-jamming distributed channel selection problem in UAV communication networks. Considering the existence of malicious jamming and co-channel interference, a location-aware cooperative anti-jamming scheme is designed for the purpose of maximizing the users' utilities. Users in the UAV group cooperate with each other via location information sharing. When the received interference energy is lower than mutual interference threshold, users conduct channel selection strategies independently. Otherwise, users take joint actions with a cooperative anti-jamming pattern under the impact of mutual interference. Aimed at the independent anti-jamming channel selection problem under no mutual interference, a Markov Decision Process framework is introduced, whereas for the cooperative anti-jamming channel selection case under the influence of co-channel mutual interference, a Markov game framework is employed. Furthermore, motivated by reinforcement learning with a ``Cooperation-Decision-Feedback-Adjustment" idea, we design a location-aware cooperative anti-jamming distributed channel selection algorithm (LCADCSA) to obtain the optimal anti-jamming channel strategies for the users with a distributed way. In addition, the channel switching cost and cooperation cost, which have great impact on the users' utilities, are introduced. Finally, simulation results show that the proposed algorithm converges to a stable solution with which the UAV group can avoid the malicious jamming as well as co-channel interference effectively.

Baduanjin exercise is a traditional Chinese health-Qigong routine, created by an ancient physician for health promotion. Its mild-to-moderate exercise intensity is suitable for individuals with medical conditions. Recently, a large number of trials were conducted to investigate the effects of Baduanjin exercise in patients with chronic obstructive pulmonary disease (COPD). It needs to be determined whether Baduanjin exercise prescription is beneficial for the management of COPD patients. Thus, we conducted a systematic review to objectively evaluate the existing literature on this topic. We searched six databases (PubMed, Web of Science, Cochrane Library, Scopus, CNKI, and Wanfang) from its inception till early May, 2018. The adapted PEDro scale was used for study quality assessment of all randomized controlled trials (RCT). The pooled effect size (Hedge’s g) of exercise capability (6-Minute Walking Test, 6-MWT), lung function parameters (forced expiratory volume in first second, FEV1; forced volume vital capacity, FVC; FEV1/FVC ratio), and quality of life were calculated based on the random-effects model. Twenty RCTs (n = 1975 COPD patients) were included in this review, with sum scores of the adapted PEDro scale between 5 and 9. Study results of meta-analysis indicate that Baduanjin is effective in improving exercise capability (Hedge’s g = 0.69, CI 0.44 to 0.94, p < 0.001, I2 = 66%), FEV1 (Hedge’s g = 0.47, CI 0.22 to 0.73, p < 0.001, I2 = 68.01%), FEV1% (Hedge’s g = 0.38, CI 0.21 to 0.56, p < 0.001, I2 = 54.74%), FVC (Hedge’s g = 0.39, CI 0.22 to 0.56, p < 0.001, I2 = 14.57%), FEV1/FVC (Hedge’s g = 0.5, CI 0.33 to 0.68, p < 0.001, I2 = 53.49%), and the quality of life of COPD patients (Hedge’ s g = - 0.45, CI -0.77 to - 0.12, p < 0.05, I2 = 77.02%), as compared to control groups. Baduanjin exercise as an adjunctive treatment may potentially improve exercise capability and pulmonary function of COPD patients as well as quality of life. Baduanjin exercise could be tentatively prescribed for COPD in combination with the conventional rehabilitation program to quicken the process of recovery. To confirm the positive effects of Baduanjin exercise for COPD patients, future researchers need to consider our suggestions mentioned in this article.

Fresh water is valuable nonrenewable resource and plays an important role of maintaining economic and social development. Condisering its large population and consumption potential, water resources deficit will certainly impede basic industries sustainable development of China in the near future. Application of sewage irrigation, to some extent, was regarded as an alternative way to solve the problem of agricultural irrigation water shortage in some areas (such as North China). However, accompanied with extensive implementation of sewage irrigation, some problems on sewage irrigation in agriculture are gradually obvious, especially serious pollution and destruction for farmland. In this paper, the effects of sewage irrigation on soil physical (soil bulk density, soil resistance to penetration and field capacity), chemical (pH, soil organic matter, nitrogen, phosphrous, patassium, heavy metal and organic pollutants) and biological characteristics (soil microorganism and enzyme activities) of farmland in China were systematically reviewed on the base of the current utilization status of China’s farmland sewage irrigation and some feasible suggestions were put forward to the development prospect for the future. This review will be beneficial for promoting healthy development of sewage irrigation and providing theoretical support for reclamation and high efficiency of effluents in China.

Facilitative glucose transporters (GLUT) are transmembrane transporter of proteins involved in glucose transport across the plasma membrane. To date, there is no information about glucose transporter 2 (GLUT2) in blunt snout bream (Megalobram aamblycephala). In this study, GLUT2 were cloned and characterized from blunt snout bream, and its-expression in response to diets with different carbohydrate levels (17.1%; 21.8%; 26.4%; 32.0%; 36.3% and 41.9% of dry matter). In this study, the full-length cDNA of GLUT2 was 2577 bp, including a 5’-untranslated region (UTR) of 73 bp, a 3’-UTR of 992 bp, and an open reading frame of 1512 bp, encoding a polypeptide of 503 amino acids with predicted molecular weight of 55.046 kDa and theoretical isoelectric point of 7.52. GLUT2 has twelve across the membrane area locating at 7-29; 71-93; 106-123; 133-155; 168-190; 195-217; 282-301; 316-338; 345-367; 377-399; 412-434; 438-460 aimo acids respectively. Conservative structure domains located at 12-477 aimo acids belonging to sugar porter family major facilitator superfamily (MFS) transporter. The blunt snout bream GLUT2 showed high identity to their orthologs in other fish species and mammals. Quantitative real-time (qRT)-PCR assays revealed that GLUT2 expression was high in the liver, intestine and kidney; highest in the liver. Compared with the control group (17.1%), high dietary carbohydrate levels (32.0%; 36.3% and 41.9%) resulted in high plasma glucose at 3h after feeding, but high plasma glucose were back to basal at 24h after feeding. Furthermore, high dietary carbohydrate levels significantly improved the glycolysis and inhibitied gluconeogenesis by augmentation of GK and PK expression, inhibition of PEPCK and G6P mRNA levels (P<0.05). However, GLUT2; GK; PK; PEPCK and G6P mRNA levels were back to basal.

The editorial explores the realm of emerging translational research in neurology and psychiatry, providing insights into various subjects, including neurodegenerative disorders and innovative therapeutic methods. The main objective is to study neurological and psychiatric disorders, such as Alzheimer's disease, with a particular emphasis on techniques for neural regeneration and repair. The editorial highlights the importance of taking a comprehensive approach to studying and treating complex neurological and psychiatric conditions. This involves thoroughly reviewing research papers on the causes, development, biomarkers, and treatment options for these conditions. The editorial emphasizes the necessity of using multidisciplinary and integrative methods to gain a deeper understanding and improve the treatment of these conditions. The development of an animal model for recurrent primary dysmenorrhea showcases the innovative techniques employed in the investigation of gynecological disorders, illustrating the capacity of translational research to connect fundamental scientific knowledge with practical medical applications. The cooperative endeavors of researchers and clinicians emphasized in this editorial lay the foundation for revolutionary advancements that hold the potential to enhance outcomes for individuals afflicted with neurological and psychiatric disorders globally.

The ZIPs (ZRT/IRT-like proteins) play critical roles in the absorption, transport, and intracellular balance of metal ions essential for various physiological processes in plants. However, little is known about the pan-genomic characteristics and properties of ZIP genes in cucumber (Cucumis sativus L.). In this study, we identified 10 CsZIP genes from the pan-genome of 13 C. sativus accessions. Among them, only CsZIP10 showed no variation in protein sequence length. We analyzed the gene structure, conserved domains, promoter cis-elements, and phylogenetic relationships of these 10 CsZIP genes derived from "9930". Based on phylogenetic analysis, the CsZIP genes were classified into three branches. Amino acid sequence comparison revealed the presence of conserved histidine residues in the ZIP proteins. Analysis of promoter cis-elements showed that most promoters contained elements responsive to plant hormones. Expression profiling in different tissues showed that most CsZIP genes were expressed at relatively low levels in C. sativus leave, stem, and tendril, and CsZIP7 and CsZIP10 were specifically expressed in root, indicating their potential involvement in the absorption and transport of metal ions. Transcriptomic data indicated that these 10 ZIP genes displayed responses to both downy mildew and powdery mildew, and CsZIP1 were significantly downregulated after both salt and heat treatments. In conclusion, this study deepens our understanding of the ZIP gene family and enhances our knowledge of the biological functions of CsZIP genes in C. sativus.

The material undergoes high temperature and high strain rate deformation process during cutting process, may induce the dynamic recrystallization behavior and result the evolution of dynamic mechanical properties of the material to be machined. In this paper, the modified Johnson-Cook(J-C) model for Nickel based powder metallurgy superalloy considering dynamic recrystallization behavior in high strain rate and temperature is proposed. The dynamic mechanical properties of the material under different strain rates and temperature conditions are obtained by quasi-static compression test and split Hopkinson pressure bar (SHPB) test. The coefficients of the modified J-C model are obtained by linear regression method. The modified model is verified by comparison with experimental and model prediction results. The results show that the modified J-C model proposed in this paper can accurately describe the mechanical properties of nickel-based powder metallurgy superalloys at high temperature and high strain rate. Which provides help for studying the cutting mechanism and finite element simulation of nickel-based powder metallurgy superalloy.

Background Acute kidney injury (AKI) is a common comorbidity in the intensive care unit (ICU), with higher mortality rate among those who receive continuous renal replacement therapy (CRRT). This study aimed to investigate the association of white blood cell (WBC) levels with all-cause mortality in AKI patients undergoing CRRT. Method We conducted a post hoc analysis of ICU patient data from multiple centers in Korea. First, the levels of WBCs were classified into four groups based on quartiles. Second, the relationship between different WBC levels and mortality was investigated with the Kaplan-Meier (K-M) survival curves, Cox proportional hazards model, and generalized additivity model (GAM). Finally, we used multiple imputation to avoid bias caused by non-randomized missing data. The endpoints were short-term (28 days) and long-term (90 days) mortality. Result In our analysis, a total of 1,100 ICU patients were included. Among them, 670 (60.90%) and 781 (71.00%) died within 28 and 90 days, respectively. K-M survival curves showed that patients with the lowest WBC levels had the highest risk of mortality for both outcomes. Adjusted multivariate Cox regression analysis confirmed that compared with the reference level (quartile 2), low WBC levels increased the risk of both 28-day mortality (quartile 1, HR = 1.43, 95% CI: 1.13–1.83, P = 0.004) and 90-day mortality (quartile 1: HR = 1.32; 95% CI: 1.05-1.66, P = 0.016). GAM analysis showed a non-linear, U-shaped relationship between pre-CRRT WBC levels and all-cause mortality (non-linear P < 0.05). Conclusion The baseline WBC level is an independent predictor of prognosis for ICU patients receiving CRRT. Patients in the lowest WBC quartile had the highest risk of all-cause mortality. These results provide further evidence that early observation and intervention may have a prognostic value for these high-risk patients.

The E-learning system has achieved great development after the pandemic. In this work, we proposed three artificial intelligence-based enhancements to our linguistic interactive E-learning system from different aspects. Compared with the original phonetic transcription exam system, our enhancements include an MFCC+CNN-based disordered speech classification module, a Transformer-based Grapheme-to-Phoneme converter, and a Tacotron2-based IPA-to-Speech speech synthesis system. This work not only provides a better experience for the users of this system but also explores the utilization of artificial intelligence technologies in the E-learning field and linguistic field.

The images captured by UAVs during inspection often contain numerous small targets related to transmission lines, which are critical and vulnerable elements for ensuring the safe operation of these lines. However, due to various factors such as the small size of the targets, low resolution, complex background, and potential line aggregation, achieving accurate and real-time detection becomes challenging. To address these issues, this paper proposes a detection algorithm called P2-ECA-EIOU-YOLOv5 (P2E-YOLOv5). Firstly, in order to address the challenges posed by the complex background and environmental interference that impact small targets, an ECA attention module is integrated into the network. This module effectively enhances the network's focus on small targets while concurrently mitigating the influence of environmental interference. Secondly, considering the characteristics of small target size and low resolution, a new high-resolution detection head is introduced, which is more sensitive to small targets. Lastly, the network utilizes the EIOU-Loss as the regression Loss function to improve the positioning accuracy of small targets, as they tend to aggregate. Experimental results demonstrate that the proposed P2E-YOLOv5 detection algorithm achieves an accuracy P of 96.0% and an average accuracy (mAP) of 97.0% for small target detection in transmission lines.

Based on the daily observation data of 2254 meteorological stations in China from 1961 to 2021 after homogenization and correction, the extreme value analysis method that combines relative threshold and absolute threshold was used to identify extreme climate events in the mainland of China, namely extreme high temperature, extreme low temperature, extreme drought, extreme precipitation and extreme typhoon events. The frequency and linear variation trends of individual extreme events in the past 60 years were investigated. On this basis, the multi extreme events composite risk grade index (MXCI) was constructed, which can objectively reflect the comprehensive characteristics of multi extreme climate events in different regions. The results show that the high value areas of MXCI were mainly located in Southeast China and Southwest China. The MXCI presented a decreasing trend in most of the western and southeastern regions of China, while an increasing trend from Southwest China to the south of Northeast China, due to the frequent occurrence of extreme high temperature, extreme drought and other extreme events in these regions.

Given the existing movable rotating plate type grading device for potatoes with a high safety factor and heavy mass, the body frame of the grading device and movable rotating plate were optimized and a lightweight design was carried out. Based on ANSYS Workbench 2022, the static analysis of the body frame before and after improvement was compared, and it was verified that the strength and deformation of the optimized body frame met the design requirements, and the weight of the optimized body frame was reduced by 32.3%. Based on the direct optimization module of ANSYS Workbench 2022, the plate length, width, and height were used as design variables for the lightweight design of the movable rotating plate. The MOGA algorithm was used to generate sixty design solutions, and the optimal combination of size parameters for the plate was 610 mm, 95mm, and1.2 mm. Compared with the whole grading device before optimization, the total mass was reduced by 22.86% after optimization. The research of this article provides a reference for the structural design and optimization analysis of potato grading devices.

This paper outlines our effort on optimizing Pulsed Magneto-Oscillation (PMO) design in order to improve the efficiency of ingot manufacturing under PMO. Our calculation and experiment provided optimized PMO coil design and special configuration. Our optimized PMO design offered us a device that enabled the operator to examine and operate the melt without losing the efficiency. In one of the designs, the equipment even refined the grain sizes. Our work also showed an optimized distance range between the coil and the melt surface that maximized the refinement effects.

A series of Ni/KIT6 catalystprecusors with 25wt.%Ni loading amount were reduced in H₂ at 400, 450, 500, and 550ºC, respectively. The studied catalysts were investigated by XRD, Quasiin-situ XPS, BET, TEM, and H₂-TPDanalysis methods.It was found that reduction temperature is an important factor affecting the hydrodeoxygenation (HDO) performance of the studied catalysts. The reduction temperature influences mainly the content of active components, crystal size, and the abilityfor adsorbing and activatingH2. The developed pore structure and large specific surface area of the KIT-6 support favored the Ni dispersion.The RT450 catalyst, which was prepared in H₂ atmosphere at 450 ºC, has the best HDO performance. Ethyl acetate can be completely transformed, and maintain 96.8% ethane selectivity and 3.2% methane selectivity at 300 ºC. The calculated apparent activation energies of the prepared catalysts increased in the following order: RT550 > RT400 > RT500 > RT450.

This paper aims to study the surface homogenization and integrity of Ti-6Al-4V alloy by longitudinal-torsional coupled ultrasonic vibration assisted ball-end milling. A method of continuous processing between the flat surface and freeform surface connection is proposed by using ultrasonic vibration assisted ball-end precision milling, during this process, it is not necessary to exchange the cutting tool. The way has been explored for changing the homogenization of surface on Ti-6Al-4V by ultrasonic vibration-assisted milling (UVAM). Cutting experiments employing three parameters, cutting speed, feed rate and depth of cut and two types of machining forms using ball-end milling with UVAM and conventional milling (CM) respectively. The high frequency cutting force, finished surface roughness, topography and residual stresses on the surface and tool wear have been measured by advanced instruments. Particularly, adopting the high frequency cutting force measurement system, it is concluded cutting force in ball-end milling decreased significantly using UVAM as against CM. Moreover, the surface roughness by UVAM with ball-end milling is much better than the CM at a high cutting speed. However, an opposite trend is observed at a low cutting speed. Especially, there is a steep decrease from Ra 0.828 μm average value at 4000 rpm to Ra 0.129 μm average value at 5000 rpm. At the same time, the homogenization of surface roughness and residual stresses decrease significantly in UVAM as compared to which in CM when taking the transversal-longitudinal ratio into consideration. Cutting experiments and measuring results are demonstrated the validity and feasibility of UVAM with ball-end milling, and this method enjoys significant advantages compared to CM process.

In this paper, quasi-static axial compression tests are performed on the nodal Moso bamboos to study the size effect on energy absorption of the bamboos and the damage pattern of the multiple bamboo columns. Experimental results show that under the same moisture content, growth age and growing environment, the specific energy absorption (SEA) of the test samples increases with the increase of the out-diameter and thickness of the bamboo columns, indicating that size effect exists for energy absorption of the Moso Bamboos. For the multiple bamboo columns, there are mainly three failure modes for the constituent single bamboo columns: splitting above the node, splitting below the node and splitting through the node. Also, the tensile tests are conducted on three kinds of dog-bone shaped bamboo samples to investigate the macroscopic tensile fracture mode in the longitudinal direction of Moso bamboos. Results show that there is no direct relationship between the fracture pattern and moisture content of the bamboos, as well as the growth age of the bamboos. However, the tensile loading rate and the shape of the dog-bone shaped bamboo sample could affect the macroscopic fracture pattern of the bamboos in some cases.

To solve large scale linear equations involved in the Fast Multipole Boundary Element Method (FM-BEM) efficiently, an iterative method named the generalized minimal residual method (GMRES)(m)algorithm with Variable Restart Parameter (VRP-GMRES(m) algorithm) is proposed. By properly changing a variable restart parameter for the GMRES(m) algorithm, the iteration stagnation problem resulting from improper selection of the parameter is resolved efficiently. Based on the framework of the VRP-GMRES(m) algorithm and the relevant properties of generalized inverse matrix, the projection of the error vector r_m+1 on r_m is deduced. The result proves that the proposed algorithm is not only rapidly convergent but also highly accurate. Numerical experiments further show that the new algorithm can significantly improve the computational efficiency and accuracy. Its superiorities will be much more remarkable when it is used to solve larger scale problems. Therefore, it has extensive prospects in the FM-BEM field and other scientific and engineering computing.

In order to further control the equivalent circulating density,a new type of annular pres-sure-reducing downhole tool for high temperature and high pressure wells-liquid-absorbing ECD tool is designed.Through this tool,the bottom hole pressure of the equivalent circulating drilling fluid can be close to its hydrostatic pres-sure,therebyachieving a deeper drilling depth.The tool is mainly composed of screw mo-tor,vortex blade,annular seal,universal joint and drill string.Its working principle is mainly to use the liquid absorption effect of the tool and the hydraulic energy of the circu-lating fluid extracted by the screw motor to convert it into mechanical energy,and to gen-erate suction force to improve the flow energy of the drilling fluid in the bottom hole an-nulusand reduce the equivalent circulation density.Based on ANSYS-FLUENT analysis andsimulation,the change of pressure drop characteristics under different drilling fluid density,displacement and tool size was simulated.The simulation results show that thedepressurization effect is 1.0MPa when the drilling fluid density is 1.2g/cm3. When the drilling fluid density is 1.5g/cm3,the depressurization is about 1.7MPa,and when thedrill-ing fluid density is 1.8g/cm3,the depressurization is about 1.9MPa.When the drilling fluid density is 2.0g/cm3,the pressure drop is about 2.3MPa.When the flow rate is from 1500-2500L/min,the maximum pressure can be reduced by 2.3MPa.When the viscosity is 40mPa•S and 60mPa•S,the pressure drop almost does not change.The increase of viscosi-ty has little effect on the pressure drop,and it is mainly affected by the flow rate under equal displacement.

Accurate calculation of non-covalent interaction energies in nucleotides is crucial for understanding the driving forces governing nucleic acid structures and functions, as well as developing advanced molecular mechanics forcefields or machine learning potentials tailored to nucleic acids. Here, we dissect the nucleotides’ structure into three main constituents: nucleobases (A, G, C, T, and U), sugar moieties (ribose and deoxyribose), and phosphate group. The interactions among these fragments and between fragment and water were analyzed. Different quantum mechanical methods were compared for their accuracy in captuing the interaction energy. The non-covalent interaction energy was decomposed into electrostatics, exchange-repulsion, dispersion, and induction using two ab-initio methods: Symmetry-Adapted Perturbation Theory (SAPT) and Absolutely Localized Molecular Orbitals (ALMO). These caculations provide the benchmark for different QM methods while providing valuable understanding of the roles of various interamolecular forces in hydrogen bonding and aromatic stacking.

Strong-aroma Baijiu is a traditional Chinese spirit distilled from grains that undergo solid-state fermentation. At the end of each fermentation cycle, a significant quantity of Huangshui accumulates at the bottom of the fermentation pit, constituting one of the primary by-products in the brewing process of strong-flavor liquor. In this report, the chemical component analysis of Huangshui obtained from a strong-flavor liquor factory revealed a diverse array of organic acids, alcohols, esters, starch, reducing sugars, amino acids, and other compounds present in Huangshui. Additionally, two specialized solid-state fermentation models were developed to investigate the formation process of Huangshui. Our findings demonstrate a positive correlation between the yield of Huangshui and the initial moisture content of fermented grains. It is concluded that Huangshui is the percolate produced during the solid-state brewing process of strong-flavor liquor, with its water content originating from the initial moisture of fermented grains.

This study evaluated five annual and eleven perennial Indian pasture legumes species for their nutritive value, dry matter, mineral contents and in vitro fermentation parameters, aiming to boost their potential as animal feed. Legume species significantly differed (p<0.05) in organic matter, crud protein (CP), ether extracts, fibres, and protein fractions. Clitoria ternatea (CT) a perennial had higher (p<0.05) buffer soluble protein (477), while neutral detergent soluble protein was highest in annually grown Lablab purpureus (420 g/kg CP). Atylosia scarabaeoides (AS) had higher NSC (392 g/kg DM) than SC (367 g/kg DM). Rapidly degradable fraction (51.7 g/kg tCHO) was lower (p<0.05) than other fractions of carbohydrate. Total digestible nutrients, digestible energy and metabolisable energy varied and values were higher for Desmenthus virgatus and lowest for Stylosanthas seabrana (SSe). The NE values for lactation (NEL), maintenance (NEM) and gain (NEG) were also higher for DV (6.6, 7.95 and 4.28) and lowest for SSe (3.54, 4.24 and 0.58 kJ/g DM), respectively. dry matter intake, digestible DM (DDM) and relative feed value of legumes differed (p<0.05) with mean values of 2.22% body weight, 592 g/kg DM and 102%, respectively. Annual grasses like Dolichos biflorus, Macroptilium atropurpureum, Rhynchosia minima (RM) were found better with micro minerals compared to other perennials. In vitro dry matter degradability, partition factor, short chain fatty acids and microbial protein production of legumes varied (P<0.05) and mean values were 578 g/kg DM, 5.61 mg DDM/mL, 2.42 mm/g and 352 mg/g, respectively. Gas and CH4 production (mL/g and mL/g DDM) varied (p<0.05) being lowest gas from AS (55.5) and highest from CT-blue (141), while CH4 production was lower (p<0.05) from CT-white and AS (8.24 and 9.14) and higher from Arachis glabrata (AG) and Arachis hagenbackii (AH) (15.2 and 15.1). Methane in total gas was low for DV, RM and CT-w (8.99, 9.72 and 9.51%) and loss of DE and ME as CH4 varied (P<0.05) amongst the legumes with mean values of 4.62 and 7.86%, respectively. Based on these findings, each legume offers unique benefits, allowing for tailored combinations of annual and perennial legumes to optimize rumen feed efficiency.

The investigation on the issue of damage diagnosis based on strain modal parameters is conducted in this paper using simply supported wooden Beams as the study's object. First, ABAQUS is utilized to create finite element models of intact wooden beams as well as wooden beams with varying degrees of damage and perform modal analyses on them. Next, damage identification studies are conducted on the wooden beam structure using various strain modal parameters (strain mode strain modal difference, strain modal curvature difference), the timber beam damage identification test then yields the modal parameters of timber beams under various damage situations, and the test findings are contrasted with those of the numerical simulation. The outcomes demonstrate that the damage identification of the test data using the three types of damage identification indexes is consistent with the results of the numerical simulation; the three types of damage identification indexes can locate the damage to timber beams, but the identification effect of the indexes is different, the best-recognized metric is the strain mode curvature difference; the next best is the strain mode difference, and the worst is the strain modes. The study's findings can serve as a guide for future damage detection on wood beams.

Poor interlaminar fracture toughness has been a major issue in glass fiber-reinforced epoxy resin (GF/EP) laminate composites. In this paper, soft carboxy-terminated liquid nitrile (CTBN) rubber particles and rigid nano-SiO2 are used to toughen the epoxy resin (EP) matrix to improve the interlayer properties of GF/EP laminate composites. The effects of adding two toughening agents on the mechanical and interlayer properties of GF/EP laminates were studied. The results showed that adding the two kinds of particles improved the mechanical properties of the epoxy matrix. When the additional amount of flexible CTBN rubber particles was 8wt%, and the rigid nano SiO2 was 0.5wt%, the fracture toughness of the matrix resin was increased by 215.8%, and the tensile strength was only decreased by 2.3% compared with the pure epoxy resin. On this basis, the effects of two kinds of particles on the interlayer properties of GF/EP composites were studied. Compared with the unmodified GF/EP laminates, the interlayer shear strength and mode Ⅰ interlayer fracture toughness is significantly improved by toughening agent, and the energy release rate GIC of interlayer shear strength and interlayer fracture toughness is increased by 109.2%, and 86.8%, respectively.

Transportation authorities aim to boost road safety by identifying risky locations and applying suitable safety measures. The Highway Safety Manual (HSM) is a vital resource for US transportation professionals, aiding in the creation of Safety Performance Functions (SPFs), which are predictive models for crashes. These models rely on Negative Binomial distribution-based regression and misinterpreting them due to unmet statistical assumptions can lead to erroneous conclusions, including inaccurately assessing crash rates or missing high-risk sites. The Florida Department of Transportation (FDOT) has introduced context classifications to HSM SPFs, complicating assumption violation identification. This study, part of an FDOT-sponsored project, investigates established statistical diagnostic tests to identify model violations and proposes a novel approach to determine optimal spatial regions for Empirical Bayes adjustment. This adjustment aligns HSM-SPFs with regression assumptions. The study employs a case study involving Florida roads. Results indicate that a 20-mile radius offers an optimal spatial sample size for modeling crashes of all injury levels, ensuring accurate assumptions. For severe injury crashes, which are less frequent and harder to predict, a 60-mile radius is suggested to fulfill statistical modeling assumptions. This methodology guides FDOT practitioners in assessing the conformity of HSM-SPFs with intended assumptions and determining appropriate region sizes.

Background: Jerusalem artichoke (Helianthus tuberosus L.) is tolerant to salinity stress and has high economic value. The salt tolerance mechanisms of Jerusalem artichoke are still unclear. Especially in the early stage of Jerusalem artichoke exposure to salt stress, the plant physiology, biochemistry and gene transcription are likely to undergo large changes. Elucidating these changes may be of great significance to understanding the salt tolerance mechanisms of it. Results: We obtained high-quality transcriptome from leaves and roots of Jerusalem artichoke exposed to salinity (300 mM NaCl) for 0 h, 6 h, 12 h, 24 h and 48 h, with 150,129 unigenes and 9023 DEGs (Differentially Expressed Genes). The RNA-seq data were clustered into time-dependent groups (nine clusters each in leaves and roots); gene functions were distributed evenly among the groups convergence. KEGG enrichment analysis showed the genes related to plant hormone signal transduction were enriched in almost all treatment comparisons. Under salt stress, genes belongs to PYL (abscisic acid receptor PYR / PYL family), PP2C (Type 2C protein phosphatases), GH3 (Gretchen Hagen3), ETR (ethylene receptor), EIN2/3 (ethylene-insensitive protein 2/3), JAZ (Genes such as jasmonate ZIM-domain gene) and MYC2 (Transcription factor MYC2) had extremely similar expression patterns. The results of qPCR of 12 randomly selected genes confirmed the accuracy of RNA-seq. Conclusions: Under the impact of high salinity (300mM) environment, Jerusalem artichoke in the seedling stage was difficult to survive for a long time, and the phenotype was severe in the short term. Based on the expression of genes on the time scale, we found that the distribution of gene functions in time is relatively even. Upregulation of the phytohormone signal transduction had a crucial role in the response of Jerusalem artichoke seedlings to salt stress, the genes of abscisic acid, auxin, ethylene, and jasmonic acid had the most obvious change pattern.

In response to the increasing energy demand in Taiwan and the global trend of renewable energy development, Kuroshio energy is a potential energy source. How to extract this invaluable natural resource has then become an intriguing and important question in engineering practices. This study conducted a study for a nozzle-diffuser duct (NDD) as the Kuroshio currents energy harvester. The computational fluid dynamics (CFD) software ANSYS Fluent was employed to calculate the drag and added mass coefficients of the duct anchored to the seabed. Those coefficients were further imported into Orcaflex to simulate the motion of the duct under normal and storm wave conditions. Results showed that the duct was stable 25 m below the sea surface under normal wave condition. When the wave condition changed to storm waves, the duct needed to dive into at least 90 m below the sea surface to regain its stability and obtain high power take-off (PTO). An optimal design nozzle-diffuser-duct was reported and a PTO peak of 15 kW was expectable in the Kuroshio currents. Once a suitable offshore platform can be developed with sixty-six NDDs, a Megawatt Kuroshio ocean current power generation system is feasible in the near future.

Akebia trifoliata is an economically important self-incompatible fruit tree in the family Lardiza-balaceae. Asexual propagation is the main strategy used to maintain excellent agronomic traits. However, the generation of adventitious roots during asexual propagation is very difficult. To study the important role of the WUSCHEL-related homeobox (WOX) transcription factor in fruit and adventitious root growth and development, we characterized this transcription factor family in the whole genome of A. trifoliata. A total of 10 AktWOXs were identified, with the fol-lowing characteristics: length (657~11328 bp), exon number (2~5), isoelectric point (5.65~9.03), amino acid number (176~361 AA), and molecular weight (20.500~40.173 kDa). 10 AktWOXs were classified into modern (6), intermediate (2), and ancient clades (2) and that all AktWOXs had undergone strong purifying selection during evolution. The expression profile of AktWOXs dur-ing A. trifoliata fruit development and adventitious root formation indicated that AktWOXs are widely involved in the development of the three fruit tissues, flesh, seeds and rind, and play an important role in the regulation of adventitious root development. Overall, this is the first study to identify and characterize the WOX family in A. trifoliata and will be helpful for further re-search on A. trifoliata fruit development and adventitious root formation.

Toxoplasma gondii is a widespread protozoan parasite that infects most warm-blooded animals, and felids can serve as intermediate and definitive hosts. Pathological diagnosis and serological and etiological investigations were conducted on a captive caracal (Caracal caracal) carcass collected from China in 2022. Pathological diagnosis revealed that cardiac insufficiency, pulmonary edema, hepatic failure, and renal insufficiency were the causes of the caracal’s death. A modified agglutination test (cut-off: 1:25) revealed that IgG antibodies against T. gondii were present in the myocardium juice, hydroperitoneum, and hydropericardium (≥1:800). A viable T. gondii (TgCaracalCHn2) strain was isolated from the tissue samples (heart, brain, spleen, and skeletal muscle) of this caracal using a mouse bioassay. The genotype of TgCaracalCHn2 was ToxoDB#5 (Type II variant), as determined by RFLP-PCR. The strain was avirulent in Swiss mice and matched the prediction of ROP18 and ROP5 gene alleles of TgCaracalCHn2 (2/2). Many tissue cysts (203 ± 265) were observed in mice brains after inoculation with TgCaracalCHn2 tachyzoites. ToxoDB#5 is the dominant genotype in North American wildlife, and this is the first documented isolation of T. gondii ToxoDB#5 from China. This indicates that caracals can accelerate the transmission of T. gondii genotypes.

A novel fluorescent probe (C460@Tb-MOFs) was designed and synthesized through encapsulating the fluorescent dye 7-diethylamino-4-methyl coumarin into terbium-based metal-organic framework by a simple ultrasonic impregnation method. It is impressive that this dye-modified metal-organic framework can specifically detect styrene and temperature upon luminescence quenching. The sensing platform of this material exhibit great selectivity, fast response and good cyclability toward styrene detection. It is worth mentioning that the sensing process undergoes a distinct color change from blue to colourless, providing conditions for accurate visual detection of styrene liquid and gas. The significant fluorescence quenching mechanism of styrene toward C460@Tb-MOFs is explored in detail. Moreover, the dye-modified metal-organic framework can also achieve temperature sensing from 298 to 498 K with high relative sensitivity at 498 K. The preparation of functionalized MOFs composites by fluorescent dyes provides an effective strategy for the construction of sensors for multifunctional applications.

Two-dimensional (2D) of transition metal dichalcogenides (TMDCs) are potential candidates for thermoelectric (TE) applications due to their unique structural properties. In this paper, we constructed an 2D monolayer TMDCs semiconductor γ-PbSn2(X=S, Se, Te) and first-principles calculations and Boltzmann transport theory are used to study the thermoelectric performance. We found that γ-PbSnX2 had an ultra-high carrier mobility up to 4.04×103 cm2V−1s−1 leading to a metal-like electrical conductivity. Meanwhile, γ-PbSnX2 both have high Seebeck coefficients, resulting in high power-factors, and also shows intrinsic low lattice thermal conductivity of 6-8 W/mK at room temperature. The lower lattice thermal conductivity and high power-factors resulted in excellent thermoelectric performance. The high ZT values of γ-PbSnS2 and γ-PbSnSe2 were as high as 2.65 and 2.96 at 900 K, respectively. The result suggests that the monolayer γ-PbSnX2 are better candidates for excellent thermoelectric performance.

The emergence of novel SARS-CoV-2 virus in China in December 2019 has turned into a global pandemic through continued spread beyond borders. This review was aimed to extract up-to-date information on the evolution, transmission, clinical manifestations, diagnosis, treatment and prevention of COVID-19 to fight against this common enemy. PubMed, Scopus and Google Scholar were the sources of literature; whereas CDC, WHO and Worldometer provided updated information. Bats served as the reservoirs of this virus while pangolin is believed as an intermediate host to transmit the virus to humans. Direct human-to-human and indirect transmissions were involved. Major clinical manifestations included fever, cough, fatigue, sputum production and shortness of breath. Chest radiographs mostly showed bilateral ground-glass opacities. Aged patients and patients with comorbidities had higher case fatality ratios. Critical cases were vulnerable to develop pneumonia, multi-organ failure and deaths. Overall situation in China has improved substantially. The European region and region of the Americas were the worst hit out of six WHO global regions. PCR based methods are used for the diagnosis of COVID-19. Severe/critical cases essentially require supportive or intensive cares. Avoiding exposure to COVID-19 is the best way to prevent the disease. Thus, this review provides a snapshot on COVID-19.

A novel coronavirus called 2019-nCoV was recently found in Wuhan, Hubei Province of China, and now is spreading across China and other parts of the world. 2019-nCoV spreads more rapidly than SARS-CoV. Unfortunately, there is no drug to combat the virus. It is of high significance to develop a drug that can combat the virus effectively before the situation gets worse. It usually takes a much longer time to develop a drug using traditional methods. For 2019-nCoV, it is now better to rely on some alternative methods to develop drugs that can combat such a disease effectively since 2019-nCoV is highly homologous to SARS-CoV. In this paper, we first collected virus RNA sequences from the GISAID database, translated the RNA sequences into protein sequences, and built a protein 3D model using homology modeling. Coronavirus main protease is considered to be a major therapeutic target, thus this paper focused on drug screening based on the modeled 2019-nCov_main_protease structure. The deep learning based method DFCNN, developed by our group, can identify/rank the protein-ligand interactions with relatively high accuracy. DFCNN is capable of performing virtual screening quickly since no docking or molecular dynamic simulation is needed. DFCNN identifies potential drugs for 2019-nCoV protease by performing drug screening against 4 chemical compound databases. Also, we performed drug screening for all tripeptides against the binding site of 2019-nCov_main_protease since peptides often show better stability, more bio-availability and negligible immune responses. In the end, we provided the list of possible chemical ligands and peptide drugs for experimental validation.

It is always a difficult task to assign the peaks recorded from vibrational spectrum. Herein we explored a new pathway of density functional theory (DFT) simulation to present three kinds of spectra of ice XIV and can be referenced as inelastic neutron scattering (INS), IR, and Raman experimental spectrum. The INS spectrum is proportional to phonon density of states (PDOS) while the photon scattering signals reflect the normal vibration frequencies near the Brillouin zone (BZ) center. Based on good agreements with experimental data, we identified the relative frequency and made scientific assignments by normal vibration modes analysis. The debating two hydrogen bond (H-bond) peaks among ice phases from INS have been discussed and the dynamic process of H-bond vibrations were found to be classified into two basic modes. we deduce that two H-bond modes are a general rule among ice family and more works are ongoing to investigate this subject.

The efficiencies of conventional triple organic Rankine cycle (TORC) configurations are restricted by the low critical temperatures of common working fluids (＜320 °C). This paper proposes a high-temperature TORC system. A near-azeotropic mixture biphenyl/diphenyl oxide (BDO), which has stellar track record in the high-temperature ORC applications, is innovatively adopted as the top and middle ORC fluid simultaneously. The top cycle evaporation temperature is up to 400 °C in view of BDO’s high stability. Five conventional organic fluids are chosen for the bottom ORC. Fundamentals of the TORC system are illustrated, and mathematical models are built. Thermo-economic performance is investigated. The results hint that the optimal thermodynamic property is achieved on the use of benzene as the bottom fluid. The maximum thermal and exergy efficiencies are respectively 40.86% and 74.14%. The largest irreversible loss occurs inside the heat exchanger coupling the middle and bottom ORCs, accounting for above 30% of the total entropy generation. The levelized energy cost (LEC) is 0.0284 $/kWh. Given the same heat source condition, the TORC system can boost efficiency by 1.02% and drive down LEC by 0.0024 $/kWh compared with a BDO mixture-based cascade ORC.

Anthracnose is one of primary diseases in tea plants that affects tea yield and quality. The geographical distribution, occurrence regularity, and agronomic measures of tea plants with anthracnose have been researched for decades. However, the pathogenic cause of anthracnose in tea plants is diverse in different regions of the world. Identifying the specific pathogenic fungi causing tea anthracnose is an essential control measure to mitigate this disease. In this study, 88 Diaporthales and 45 Colletotrichum isolates were obtained from 3 different types of diseased tea leaves. Based on multilocus phylogenetic and morphological analysis, 3 known species, including Discula theae-sinensis, Diaporthe ueckerae, Diaporthe lithocarpus, and 3 indistinguishable species of Diaporthales were identified. In adddition, 8 known species of Colletotrichum, C. fructicola, C. camelliae, C. aenigma, C. siamense, C. henanense, C. karstii, C. tropicicola, C. gigasporum, were identified. This study is the first to report C. tropicicola and C. gigasporum in tea plant in China. Discula theae-sinensis was the most common species in this study and caused disease lesions around wounded areas of tea leaves. The dual trials in vitro indicated Discula theae-sinensis and Colletotrichum were slight inhibition. Co-inoculating Discula theae-sinensis and C. fructicola was superior to single inoculation at low concentration.

Piceatannol is a naturally occurring polyphenolic compound that is widely found in grapes, blueberries, mushrooms, passion fruit and other edible fruits and vegetables. It has a variety of biological activities and pharmacological effects, including anti-inflammatory, antioxidation, antiaging, antiviral, antitumor, anticancer, antiatherosclerosis, antiparasitic, immunoregulatory, and cardiovascular protection effects. The aim of this study was to investigate the antiherpesvirus effects of piceatannol. Pseudorabies virus (PRV) belongs to the family Herpesviridae. PRV has a wide host range and can cause cytopathic effects (CPEs) in PK-15 cells. Therefore, PRV was used as a model to study the antiherpesvirus effect of piceatannol. In this study, we evaluated the antiviral activity of piceatannol against PRV in vitro and in vivo. The results showed that piceatannol could reatrain PRV multiplication in PK-15 cells in a dose-dependent manner. The 50% inhibitory concentration (IC50) was 0.0307 mg/mL, the IC50 was 0.0307 mg/mL, and the selectivity index (SI, CC50/IC50) was 3.68. The addition of piceatannol at different stages of PRV infection inhibited the viral adsorption and intracellular replication phases of PRV. Piceatannol significantly reduced the expression levels of the IE180, EP0, UL29, UL44, US6 and UL27 genes of PRV within 48 h, significantly reduced the expression levels of the PRV gB and gD proteins, and reduced PRV-induced apoptosis. Molecular docking showed that piceatannol had good binding activity with the PRV gB and gD proteins. The results of animal experiments in vitro indicated that piceatannol could delay the onset of disease, improve the survival rate of the mice (14.3%), reduce the viral load in the brain and kidney of the mice, alleviate the pathological changes in the mouse tissues and organs, and increase the levels of TNF-α, IEN-γ and IL-4 in the serum of the mice. These data indicate that piceatannol has good anti-PRV activity in vitro and in vivo, indicating that it could be a novel antiherpesvirus infection agent in the future.

Biotic and abiotic factors influence the formation of fungal-algal pairings in lichen symbiosis. It is poorly known which factors determine the specific associations, especially when distantly related fungi are considered. Here, we investigated the effect of different drivers on the association patterns of taxonomically diverse lichenized fungi and their trebouxioid symbiotic partners. In 200 samples collected across three biomes, we found 41 species of lichenized fungi, associating with 16 species of trebouxioid green algae, of which 62% were previously unreported. Species identity of the fungal and algal partner had the greatest effect on the outcome of the symbiosis compared with abiotic factors such as climatic variables and geographic distance. Partner specificity was found to be higher in tropical regions than in temperate and arctic regions. Co-phylogenetic analyses indicated congruent phylogenies of trebouxioid algae and associated fungi, rejecting their random associations. Evolutionary mechanisms contributing most to the observed phylogenetic patterns were ‘loss’ and ‘failure to diverge’ of the algal partners. This study broadens our knowledge of fungi-algae symbiotic patterns in view of Trebouxia-associated fungi.

Controlling the selectivity of detonation initiation reaction of explosive is a Holy Grail, and it seems to be an “idiot's daydream”, by strengthening external electric field, to reduce the explosive sensitivity. The effects of external electric fields on the initiation reactions in NH2NO2∙∙∙NH3, a model system of the nitroamine explosive with alkaline additive, were investigated at the MP2/6-311++G(2d,p) and CCSD/6-311++G(2d,p) level. The concerted effect in the intermolecular hydrogen exchange is characterized by an index of the imaginary vibrations. Due to the weakened concerted effects by the electric field along the −x-direction opposite to the “reaction axis”, the dominant reaction changes from the hydrogen exchange to 1,3-intramolecular hydrogen transference with the increase of the field strengths. Furthermore, the stronger the field strengths, the higher the barrier heights become, indicating the lower sensitivities. Therefore, by strengthening the field strength and adjusting the orientation between the field and “reaction axis”, not only can the reaction selectivity be controlled, but also the sensitivity can be reduced, in particular under a super-strong field. Thus, a traditional concept, which the explosive is dangerous under the super-strong external electric field, is broken theoretically. Compared to the neutral medium, the low sensitivity of the explosive with alkaline can be achieved under the stronger field. Employing atoms in molecules, reduced density gradient and surface electrostatic potentials, the origin of the reaction selectivity and sensitivity change is revealed. This work provides a new idea to the technical improvement for adding the external electric field into the explosive system.

We have repeated the experiment performed recently by Krasznahorkay et al., (Phys. Rev. Lett. 116, 042501 (2016)), which may indicate a new particle called X17 in the literature. In order to get a reliable, and independent result, we used a different type of electron-positron pair spectrometer which have a more simple acceptance/efficiency as a function of the correlation angle, but the other conditions of the experiment were very similar to the published ones. We could confirm the presence of the anomaly measured at the Ex=18.15 MeV resonance, and also confirm their absence at the Ex=17.6 MeV resonance, and at Ep= 800 keV off resonance energies.

To investigate the effects of plant polysaccharides combined with boric acid on digestive function, immune function, and harmful gas and heavy metal contents in faeces of finishing pigs, for this study, 90 healthy three-way cross-bred pigs were selected and randomly divided into five groups: Con) A control, fed basic feed; BA) fed basic feed supplemented with 40 mg/kg of boric acid; BA+APS) fed basic feed supplemented with 40 mg/kg of boric acid and 400 mg/kg of Astragalus polysaccharides; BA+GLP) fed basic feed supplemented with 40 mg/kg of boric acid with 200 mg/kg of Ganoderma lucidum polysaccharides; and BA+EPS) fed basic feed supplemented with 40 mg/kg of boric acid and 500 mg/kg of Echinacea polysaccharides. Compared with the Con, the average daily gain (ADG) and trypsin activity were higher in BA, along with there being increased glutathione peroxidase (p < 0.05); furthermore, lower malondialdehyde content and harmful substance emissions from manure were observed (p < 0.05). Compared with BA, increases in ADG, gain-to-feed ratio (G/F), trypsin, and maltase activities were observed in BA+EPS (p < 0.05), as well as a lower NH3 emissions (p < 0.05). Compared with BA, BA+APS exhibited higher ADG, average daily feed intake (ADFI), G/F, trypsin, and maltase activities (p < 0.05), while H2S emissions were lower (p < 0.05). And Taken together, our findings reveal that supplementation with boric acid and plant polysaccharides in the diet of finishing pigs synergistically improved their growth performance, trypsin and maltase activities, and immune function, while also discovered the intestinal digestive enzymes, serum inflammatory factors, oxidative stress responseand emissions of harmful gases and heavy metals from feces and urine were tightly related, further reducing the impact of fecal pollution generated by modern animal husbandry on the environment.

Due to the special terrain of Urumqi (in the valley area), which often triggers strong foehn weather, and causes huge losses to local people's lives and social economy. This study uses in-situ surface meteorological variables (including the hourly temperature, pressure, humidity, wind, etc.) from the Urumqi Meteorological Station (downstream station, DS) and the Dabancheng Meteorological Station (upstream station, US) in the Middle Tianshan Valley and NCEP/NCAR reanalysis data from 2008 to 2022. A dataset of the foehn weather process at DS in the past 15 years is established and the variation patterns of each meteorological variable during the process of foehn is analyzed. Based on the physical mechanism of the occurrence of foehn, a three-element identification standard for foehn in Urumqi is established by comparing and analyzing the variation of wind direction (WD), wind speed (WS), and the difference of potential temperature (Δθ) between DS and US during the period of foehn and non-foehn from 2013 to 2022, namely: 94°≤ 2-minute average WD ≤168°, 2-minute average WS ≥2.0 m/s, and Δθ between DS and US ≥ 0.29 K. According to the test and evaluation, the three-element identification standard has an accuracy of 82.96%, and a hit rate of 89.50% for the occurrence of foehn in Urumqi from 2008 to 2012. Moreover, the hit rate of foehn identification is 100% for strong wind or above (i.e., 2-minute average WS ≥10.8 m/s) WS. In addition, combined with two predictors of sea-level pressure difference (ΔP) and Δθ between DS and US, forecasting foehn can be more accurately predicted than a single forecasting factor. When ΔP ≤ -12 hPa and Δθ≥5 K, the probability of the occurrence of foehn is more than 90%. This study provides certain reference and application value for the weather forecasting operation of foehn.

Light-colored and transparent polyimide (PI) films with good high-temperature dimensional stability are highly desired for advanced optoelectronic applications. However, in practice, the simultaneous achievement of good optical and thermal properties in one PI film is usually difficult due to the inter-conflicting molecular design for the polymers. In the present work, a series of PI-SiO2 nanocomposite films (ABTFCPI) were developed based on the PI matrix derived from hydrogenated pyromellitic anhydride (HPMDA) and an aromatic diamine containing benzanilide and trifluoromethyl substituents in the structure, 2,2'-bis(trifluoromethyl)-4,4'-bis[4-(4-aminobenzamide)]biphenyl (ABTFMB). The inorganic SiO2 fillers were incorporated into the nanocomposite films with the form of colloidal nanoparticles dispersed in the good solvent of N,N-dimethylacetamide (DMAc) for the PI matrix. The derived ABTFCPI nanocomposite films showed good film-forming ability, flexible and tough nature, good optical transparency, and good thermal properties with the loading amounts of SiO2 up to 30 wt% in the system. The ABTFCPI-30 film with the SiO2 content of 30 wt% in the film showed the optical transmittance of 79.6% at the wavelength of 400 nm (T400) with a thickness of 25 μm, the yellow index (b*) of 2.15, and the 5% weight loss temperatures (T5%) of 491 oC, which are all comparable to those the pristine ABTFCPI-0 matrix without filler (T400=81.8%; b*=1.77; T5%=492 oC). Meanwhile, the ABTFCPI-30 film exhibited obviously enhanced high-temperature dimensional stability with the linear coefficients of thermal expansion (CTE) of 25.4×10-6/K in the temperature range of 50 to 250 oC, which is much lower than that of the AMTFCPI-0 film (CTE=32.7×10-6/K).

The rapid development of electrochemical CO2 reduction offers a promising route to convert in-termittent renewable energy into products of high value-added fuels or chemical feedstocks. However, low faradaic efficiency, low current density, and a narrow potential range still limited the large-scale application of CO2RR electrocatalyst. Herein, monolith 3D bi-continuous nano-porous Bismuth (np-Bi) electrodes are fabricated via a simple one-step electrochemical dealloying strategy from Pb-Bi binary alloy. The unique bi-continuous porous structure ensures highly effective charge transfer, meanwhile the controllable millimeter-size geometric porous structure enables easy catalyst adjustment to expose highly suitable surface curvatures with abundant reactive sites. This results in a high selectivity of 92.6% and superior potential window (400 mV, selectivity >88%) for electrochemical reduction of carbon dioxide to formate. Our scalable strategy provides a feasible pathway for mass-producing high-performance and versatile CO2 electrocatalysts.

An optimal scheduling strategy for cooling, heating and power (CCHP) joint-power-supply system is proposed to improve energy utilization and minimize costs in this paper. Firstly, the mathematical model of CCHP system is established. Particle swarm optimization (PSO) is used to optimize the regularization coefficient C and the kernel parameter λ which can affect the prediction accuracy of KELM(PSO-KELM). Then PV generation and load prediction model are established by PSO-KELM. In order to jump out of local optimal solution, Cauchy variation is introduced in SFLA local update, and adaptive mutation operation is carried out on SFLA individuals. The predictions of PV generation and load power by PSO-KELM are imported into the objective function, and the microgrid dispatching model is solved by the improved SFLA algorithm. Compared with the traditional GA-KELM and KELM, PSO-KELM has faster convergence and prediction accuracy. Compared with the power supply division, the operation cost of the power grid is reduced by the proposed optimization dispatching strategy of CCHP micro-grid.

Teaching, learning, research, and development are all supported in a favorable atmosphere at the University of Lagos (UNILAG). The wetland systems made up of freshwater that are extremely biodiverse makeup about 10% of the total land area. Flooding, deforestation, excessive sedimentation, blockages to streams, abuse, overuse, and invasion of wetlands are some of the recent environmental challenges that the university faced. Urban heat island impacts, contaminants in the air, wetland degradation, social issues including stress, and a detachment from nature are all major concerns. With the green corridor behind the faculties of law and management science serving as a model supported by sustainability as a true foundation for UNILAG's campus landscapes, this article investigates the sustainable restoration of wetlands within the boundaries of the university. The use of qualitative techniques was employed, utilizing the Strengths-Weaknesses-Opportunities-Threats (SWOT) analysis. Additionally, a geospatial mapping of the wetlands and tributaries that connect the Lagos Lagoon was conducted to evaluate the intrinsic ecological goods and services through a series of analytical steps, beginning with an analysis of the land area, current biodiversity, hydrology, and its potential through landscape mapping and analysis. The biophysical setup, landscape features, climatic data analysis, the ecological goods and services derived from the wetlands, and the records of flooding and rainfall are all included in the geospatial evaluation and analysis. The educational institution's site planning for the remediation of its wetlands takes into account the actual evolution of the area's drainage network. Throughout the wetlands, low carbon emissions are generated by off-road bike lanes, trails for walking, and raised hardwood platforms. Combining native plant species and park furniture, the academic landscape atmosphere will be improved in each of the wetlands and aesthetic values. the country's "University of First Choice" and its biophysically restored wetlands will help illuminate the landscape while the green corridors have an innate ability to attract human affinity within the academic community. All of these elements are implemented following an environmentally friendly landscape planning, management, design model, and enforcement process.

High molecular weight glutenin subunits (HMW-GS) and Low molecular weight glutenin subunits (LMW-GS) in mature grains play important roles in the formation of glutenin macropolymer and gluten quality. To characterize the expressed glutenin genes of the bread wheat variety Xinmai 26 during seed development, in this study, we measured the dough rheological properties of mature grains through farinograph and gluten testing system, and revealed its strong gluten quality. The compositions of HMW-GS and LMW-GS were analyzed by sodium dodecyl sulfate-polyacrylamide gel electrophoresis (SDS-PAGE) and matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOF-MS). Further, a total of 18 full-length transcripts were obtained by third-generation RNA sequencing, including 5 transcripts of HMW-GS genes and 13 transcripts of LMW-GS genes (8 intact genes and 5 pseudogenes). The deduced protein structures of transcript sequences exhibit the typical HMW-GS and LMW-GS structural characteristics. Moreover, a specific functional marker was developed to make better use of the extra cysteine residue of 1Dx5 subunit. This study provides an efficient method to accurately identify glutenin genes in bread wheat through matching full-length transcripts to their spectrum of glutenin, which will be helpful to understand the contributions of glutenin genes to wheat quality.

The nature of bone homeostasis is the coordination between the osteoblasts (OBs) and osteoclasts (OCs). However, abnormal activation of osteoclasts (OCs) could compromise the bone homeostasis. Thus, it is imperatively urgent to explore effective medical interventions for patients. NO/guanylate cyclase (GC)/cGMP signaling cascade has been widely reported in regulating bone metabolism, and GC plays a significantly critical role. Vericiguat, a novel oral soluble guanylate cyclase (sGC) stimulator, has been firstly reported in 2020 to treat patients with heart failure. However, the effect of Vericiguat on the function of OCs has not been explored. In this present study, we found that the concentration range of Vericiguat between 0-8uM was none- cytotoxic to BMMs. Vericiguat could enhance differentiation of OCs at concentration of 500nM, whereas it inhibited differentiation at 8 uM in terms of the number and size of OCs. In addition, Veirciguat also showed dural effect on RANKL‐induced OC fusion and bone resorption in a concentration‐dependent manner. Further, molecular assay suggested that the dually regulatory effect of Vericiguat on OCs was mediated by the bidirectional activation of IκB-α/NF-κB signaling pathway. Taken together, our present study demonstrated the dual effects of Vericiguat on the formation of functional OCs in a concentration-dependent manner. The regulatory effect of Vericiguat on OCs was mediated by the bidirectional activation of IκB-α/ NF-κB signaling pathway, and a potential balance between IκB-α/ NF-κB signaling pathway and sGC/cGMP/VASP may exist.

Viral infection can regulate the cell cycle, thereby promoting viral replication. Hijacking and altering the cell cycle are important for the virus to establish and maintain latent infection. Previously, Spodoptera exigua multiple nucleopolyhedrovirus (SeMNPV) latently infected P8-Se301-C1 cells, which grew more slowly than Se301 cells and interfered with homologous SeMNNPV superinfection, were established. However, the effects of latent and superinfection with baculoviruses on cell cycle progression remain unknown. In this study, the cell cycle profiles of P8-Se301-C1 cells, and SeMNPV or Autographa californica mutiple nucleopolyhedrovirus (AcMNPV) infected P8-Se301-C1 cells were characterized by flow cytometry. The results showed that replication-related genes MCM4, PCNA, and BAF were down-regulated (p < 0.05) in P8-Se301-C1 cells and the S phase of P8-Se301-C1 cells was longer than that of Se301 cells. P8-Se301-C1 cells infected with SeMNPV did not arrest in G2/M phase and or affect the expression of Cyclin B and cyclin-dependent kinase 1 (CDK1). Furthermore, when P8-Se301-C1 cells were infected with SeMNPV after synchronized treatment with hydroxyurea and nocodazole, light microscopy and qRT-PCR analysis showed that compared with unsynchronized cells and S and G2/M phase cells, SeMNPV-infected P8-Se301-C1 cells in G1 phase induced G2/M phase arrest, and the amount of virus adsorption and intracellular viral DNA replication were significantly increased (p < 0.05). In addition, the BV production and the OB containing cells were both increased at 120 h post-infection (p < 0.05). The expression of Cyclin B and CDK1 was significantly down-regulated at 48 h post infection (p < 0.05). Finally, arrest of SeMNPV-infected G1 phase cells in the G2/M phase increased BV production (p < 0.05) and the number of OB containing cells. In conclusion, G1 phase infection and G2/M arrest are favorable to SeMNPV proliferation in P8-Se301-C1 cells, thereby alleviating the homologous superinfection exclusion. The results contribute to a better understanding of the relationship between baculoviruses and insect cell cycle progression regulation.

Precise determination of the tectonothermal events at the Qinling-Qilian junction is extremely significant for understanding the tectonic evolution of the eastern branch of the Paleo-Tethys. The Banpo porphyry outcrops in the northern margin of the North Qinling were chosen as the research subject, and its formation and tectonic environment were analyzed using Zircon U-Pb age estimation and geochemical studies. The results indicated the final stage of the Triassic orogeny and the closure phase of the Paleo-Tethys. The weighted average values of 206Pb/238U ages of samples from 3 sites of the Banpo porphyry corresponded to 213.4 ±2.1 Ma (MSWD = 0.56), 213.0 ±1.6 Ma (MSWD = 0.92), and 213.2 ±4.4 Ma (MSWD = 1.6). This study revealed that the Banpo porphyry was formed during the Late Triassic (Norian). The porphyry with high SiO2 and high alkali is typical A-type granite, which belongs to the weak peraluminous shoshonite series. All the samples are rich in low rare earth elements. However, the heavy rare earth elements are low, especially Eu, which exhibits a seagull-type right-leaning partitioning curve. In addition, based on the regional geological data, it can be concluded that the Banpo porphyry was formed during the transition period from a post-orogenic environment to a non-orogenic environment. This study indicated the closure of the Paleo-Tethys-Mianxian-Lveyang Ocean by the Late Triassic as well as the completion of the collision between the North China and Yangtze Blocks along the Qinling orogenic belt.

Three monoruthenium complexes 1(PF6)23(PF6)2 bearing a N(CH3)-bridged ligand have been synthesized and characterized. These complexes have a general formula of [Ru(bpy)2(L)](PF6)2, where L is a 2,5-di(N-methyl-N-(pyrid-2-yl)amino)pyrazine (dapz) derivative with various substituents and bpy is 2,2′-bipyridine. The photophyscial and electrochemical properties of these compounds have been examined. The solid-state structure of complex 3(PF6)2 is studied by single crystal X-ray analysis. These complexes show two well-separated emission bands centered at 451 and 646 nm (max = 195 nm) for 1(PF6)2, 465 and 627 nm (max = 162 nm) for 2(PF6)2, and 455 and 608 nm (max = 153 nm) for 3(PF6)2 in dilute acetonitrile solution, respectively. The emission maxima of the higher-energy emission bands of these complexes are similar, while the lower-energy emission bands are dependent on the electronic nature of substituents. These complexes display two consecutive redox couples owing to the stepwise oxidation of the N(CH3)-bridged ligand and ruthenium component. In addition, density functional theory (DFT) and time-dependent density functional theory (TD-DFT) calculations are carried out to elucidate these experimental findings.

Bis-benzimidazole derivative (BBM) molecule, consisting of two 2-(2’-Hydroxyphenyl) benzim-idazole (HBI) halves, has been synthesized and successfully utilized as a ratiometric fluorescence sensor for the sensitive detection of Cu2+ based on enol-keto excited state intramolecular proton transfer (ESIPT). In this study, we strategically implement femtosecond stimulated Raman spec-troscopy and several time-resolved electronic spectroscopies, aided by quantum chemical calcula-tions to investigate the detailed primary photodynamics of BBM molecule. The results demonstrate that the ESIPT from BBM-enol* to BBM-keto* was observed in only one of HBI halves with a time constant of 300 fs, after that, the rotation of the dihedral angle between two HBI halves generate a planarized BBM-keto* isomer in 3 ps, leading to dynamics red shift of BBM-keto* emission.

Because of the widespread use of bisphenol analogues (BPs) as the alternatives to bisphenol A (BPA), they have attracted considerable attention for health risk in aquatic ecosystems. The occurrence and distribution of six BPs were researched in soluble phase (< 5 kDa), colloidal phase (5 kDa to 1 µm) and suspended particulate matter (SPM > 1 µm) in a water diversion project of Nanjing, China. Except for bisphenol Z, all BPs were detected in the two or three phases, the total concentrations of detected BPs were 161-613 ng/L, 5.19-77.2 ng/L and 47.5-353 ng/g for the soluble phase, colloidal phase and SPM, respectively. Among the detected compounds, BPA still the dominant BPs in the soluble and colloidal phases, followed by BPS, while BPAF was the major contaminant in SPM, followed by BPA. The mean contribution proportions of colloids were 1-2 orders of magnitude higher than SPM, suggesting that colloids have an obvious impact on regulating BPs’ environmental behaviors. In terms of spatial distribution, although the water diversion project could reduce the pollution levels of BPs, which might further affect the ecological security of the Yangtze River.

A typical vibrational spectrum in the ice phase has four separate bands: translation, libration, bending and stretching. Ice X, the final ice phase under high pressure, shows an exotic vibrational spectrum. Theoretically, an ideal crystal of ice X only has one peak at 998 cm-1 for Raman scattering and two peaks at 450 cm-1 and 1507 cm-1 for infrared absorption in this work. These three characteristic peaks are indicators of the phase transition between ice VII/VIII and ice X. Despite much experimental and theoretical work on ice X, only this study has clearly indicated these characteristic peaks in the region of the IR band. The phonon density of states shows quite different features than ice VIII, which could be verified by inelastic neutron scattering in the future. The dynamic processes of 15 vibrational normal modes are discussed and the typical hydrogen bonds are missing.

The three-point bending behavior of a single Au nanowire deformed with an atomic force microscope was monitored by coherent X-ray diffraction using a sub-micrometer sized hard X-ray beam. While three-dimensional reciprocal-space maps were recorded before and after deformation by standard rocking curves, they were measured by scanning the energy of the incident X-ray beam during deformation at different loading stages. The mechanical behavior of the nanowire is visualized in reciprocal space and a complex deformation mechanism is described. In addition to the expected bending of the nanowire, torsion is detected. Bending and torsion angles are quantified from the high resolution diffraction data.

Metal and alloy toughening was the core and long-term research direction in materials filed. As grain size had bimodal distribution, micro/nano-structured alloys presented excellent comprehensive mechanical properties, and this had become one of the research hotspots and developing trends in the field of nanotechnology. In-situ tensile test was a direct and effective method to study the deformation mechanism of materials, which revealed the multiple mechanisms responding to feature grain sizes and provided reliable experimental means and research technique. Research on development of in-situ technique and its applications in mechanical properties was reviewed in this paper according to the recent advances on the modern mechanical properties for high strength and high plasticity alloy at home and abroad. The disadvantages of the present study of preparation methods and investigation techniques for high-performance alloy had been concluded. Finally, the development prospects of high strength and high plasticity alloy materials were analyzed.

Forward-bias hole injection from 10 nm-thick p-type Nickel Oxide layers into 10 um-thick n-type Gallium Oxide in a vertical NiO/Ga2O3 p-n heterojunction leads to more than a factor of 2 enhancement of photoresponse measured from this junction. While it takes only 600 seconds to obtain such a pronounced increase in photoresponse, it persists for hours, indicating feasibility of photovoltaic device performance control. The effect is ascribed to charge injection-induced increase of minority carrier (hole) diffusion length (resulting in improved collection of photogenerated non-equilibrium carriers) in n-type beta-Ga2O3 epitaxial layers, due to trapping of injected charge (holes) on deep meta-stable levels in the material and subsequent blocking of non-equilibrium carrier recombination through these levels. Suppressed recombination leads to increased non-equilibrium carrier lifetime, in turn determining a longer diffusion length and being the root-cause for the effect of charge injection.

The objective of this study was to investigate the effects of body weight gain during the cashmere non-growing period on cashmere production performance and secondary hair follicle activity, to provide a theoretical basis for appropriate supplementary feeding of cashmere goats. Fifty Inner Mongolian cashmere goats aged 2-4 years old were randomly selected and weighed in May and September 2019, respectively. Based on body weight gain between the two weights, the experi-mental ewe goats were divided into two groups: 0-5.0 kg group (n = 30) and 5.0-10.0 kg group (n = 20). Skin samples and cashmere samples were collected. Results of Pearson correlation analysis showed that body weight gain during the cashmere non-growing period had a moderate and strong positive correlation with cashmere yield (P = 0.021) and cashmere staple length (P = 0.002) respectively, but did not correlate with cashmere diameter (P = 0.254). Compared with cashmere goats with a body weight gain of 0-5.0 kg, cashmere goats with a body weight gain of 5.0-10.0 kg had a 17.10% increment in cashmere yield (P = 0.037), 8.09% increase in cashmere staple length (P=0.045) and had no significant difference in cashmere diameter (P = 0.324). Results of Pearson correlation analysis showed that there was a strong positive correlation between body weight gain and the population of active secondary hair follicles in the skin of cashmere goats (P < 0.01). Compared with cashmere goats with a body weight gain of 0-5.0 kg, cashmere goats with a body weight gain of 5.0-10.0 kg had an increase in the population of active secondary hair follicles (P < 0.05). In conclusion, the body weight gain during the cashmere non-growing period had a sig-nificant effect on secondary hair follicle activity and cashmere production performance in cash-mere goats. Since body weight gain reflects nutritional level to a certain extent, this study suggests that nutritional manipulations such as supplementary feeding during cashmere non-growing periods can increase cashmere production performance. However, specific nutritional manipula-tions during the cashmere non-growing period need further research to increase cashmere pro-duction performance.

The gut microbiota plays a crucial role in childhood obesity, and diet is a dominating driver. The effects of fructo-oligosaccharides (FOS), as a dietary fiber, on the composition and metabolism of gut microbiota in healthy children was investigated by vitro fermentation system with a reformative YCFA medium (rich in tryptic hydrolysates of meat). The 16S rRNA sequencing technology was utilized to analyze the varieties of gut microbiota. Measurement of short chain fatty acids (SCFAs) and gases were used by the gas chromatograph. Majorbio Cloud Platform and MetOrigin, as the interactive cloud server, perform the microbiota analysis, the metabolic pathway enrichment analysis, the statistical correlations, and biological relationships using network visualization. We found that the FOS group significantly regulated the composition and metabolism of gut microbiota. The co-metabolism network showed that 3 metabolites were related to 6 differential bacteria and 8 metabolism pathways. These findings suggest that dietary fiber could regulate the composition of gut microbiota and its metabolites in a better direction, but when dietary fiber participates in precision nutrition formula, it may be relevant for precision obesity, may help identify windows of opportunity for the dietary intervention of childhood obesity.

At present, the drilling rig for deep seabed shallow strata is widely used in the exploration of ocean cobalt-rich crust resources and other fields, which not only can obtain solid core samples at a specific station, but the operation process is relatively safe. This paper mainly presents the structure and mechanism of mobile drilling rig in acquiring the seafloor cores (up to 1.5 m long). Based on the function of the AMESim software, the hydraulic propulsion system model of mobile drilling rig is established, which is the basis and core part of the mobile drilling rig. Moreover, the control methods of closed-loop and PID are respectively used to control the hydraulic propulsion system for simulation analysis. Through the comparison of simulation results, it is found that the PID control method is more convincing in verifying the design rationality of hydraulic propulsion system. In the simulation of the PID-controlled hydraulic propulsion system, the co-simulation technology of AMESim and Matlab/Simulink not only establishes the hydraulic model and control model, but also determines the relevant simulation parameters, which is helpful to improve the system simulation efficiency. In its verification deployment in the South China Sea, the mobile drilling rig has been operated for many times at different depths, and some cores have been successfully obtained. Furthermore, the mobile drilling rig has been used during the 55th Voyage of China Oceanic Scientific Expedition supported by China Ocean Mineral Resources R&D Association. Several sites were explored and a large number of cobalt-rich crust cores were obtained. The powerful theory and sea trails are provided to support for the further research on survey of the abyssal resource.

Memory and emotion are highly vulnerable to psychiatric disorders like post-traumatic stress disorder (PTSD), which has been linked to serotonin (5-HT) metabolism disruptions. In fact, over 90% of the 5-HT precursor tryptophan (Trp) is metabolized via the Trp-kynurenine (KYN) meta-bolic pathway, producing a variety of bioactive molecules. The aadat (kat2) gene encodes mito-chondrial kynurenine aminotransferase (KAT) isotype 2, responsible for kynurenic acid (KYNA) production. Little is known about its role in behavior. In CRISPR/Cas9-induced aadat knockout (kat2−/−) mice, we examined the effects on emotion, memory, motor function, Trp and its metabolite levels, enzyme activities in the plasma and the urine of 8-week-old males compared to wild-type mice. Transgenic mice showed more depressive-like behaviors in the forced swim test, but not in the tail suspension, anxiety, or memory tests. They also had fewer center field and corner entries, shorter walking distances, and fewer jumping counts in the open field test. Plasma metabolite levels are generally consistent with those of urine: KYN, antioxidant KYNs, 5-hydroxyindolacetic acid, and indole-3-acetic acid levels are lower; enzyme activities in KATs, kynureninase, and monoamine oxidase/aldehyde dehydrogenase are lower, but kynurenine 3-monooxygenase is higher; and ox-idative stress and excitotoxicity indices are higher. Transgenic mice show depression-like behavior in a learned helplessness model, emotional indifference, and motor deficits, coupled with a decrease in KYNA, a shift of Trp metabolism toward the KYN-3-HK pathway, and a partial decrease in the gut microbial Trp-indole pathway metabolite. This is the first evidence that deleting the aadat gene causes depression-like behaviors that are unique to despair experience, which appears to be linked to excitatory neurotoxic and oxidative stresses. This may lead to the development of a double-hit preclinical model in experience-based depression, better understanding of these complex condi-tions, and more effective therapeutic strategies by elucidating the relationship between Trp me-tabolism and PTSD pathogenesis.

Instrumental activities of daily living (IADL) training is critical in clinical practice of occupational therapy (OT) for stroke patients. In the conventional approaches, the therapists simulate various occupational tasks in their healthcare settings or reach their nearby real circumstances for the training. As an alternative technology, immersive virtual reality (IVR) has been used widely in stroke rehabilitation for years; however, limited research has compared occupational performances between virtual and real environments. Our team has established a novel IVR shopping training system for stroke rehabilitation. We recruited 10 stroke patients from our department to test the system. All patients attempted to implement shopping tasks in the virtual and real environments respectively. The Wilcoxon test showed no significant differences between virtual and real environments in memory capacity and time-consuming for implementing tasks, and memory capacities in virtual and real environments presented excellent correlations with the IADL assessment. This study suggests that IVR shopping tasks can be used as an alternative approach in rehabilitation when there is limited resource for implementing shopping training in a real environment, while the psychometric property, clinical effect and the effect transferred to the real environment induced by virtual training require further study.

Different bone bruise patterns observed on magnetic resonance imaging (MRI) after non-contact anterior cruciate ligament (ACL) rupture and lateral patellar dislocation may indicate different injury mechanism of knee. In order to investigate the typical bone bruising patterns after ACL rupture and patellar dislocation. In this study, 77 ACL rupture and 77 patellar dislocation patients’ knee MR images with bone bruises between August 2020 and March 2022at our institution were selected and analyzed, respectively. Sagittal and transverse planes images were used to determine the bone bruise location in the lateral-medial and superior-inferior directions of the MR images. The presence, location, and intensity of the bone bruises within specific compartments of the femur and tibial after ACL rupture and patellar dislocation were recorded. Relative bone bruise patterns of the ACL rupture and patellar dislocation were classified and analyzed. Results showed that there were 4 kinds of bone bruise (1-,2-,3-,4- bone bruises) patterns after ACL rupture. The most common two patterns after ACL rupture were 3- bone bruises (including lateral side of femur and both lateral and medial side of tibia, LF+BT; both lateral and medial side of femur and lateral side of tibia, BF+LT, medial side of femur and both lateral and medial side of tibia, MF+BT) followed by 4- bone bruises (both lateral and medial side of femur and tibia, BF+BT), 2- bone bruises (LF+LT, lateral side of femur and tibia; MF+LT, medial side of femur and lateral side of tibia; LF+MT, lateral side of femur and medial side of tibia; MF+MT, medial side of femur and tibia; 0+BT, both lateral and medial side of tibia;), and 1- bone bruise (0+LT, only lateral side of tibia). There was only 1 pattern bone bruise (latera femur and medial patella bone bruise) of patellar dislocation, the most common pattern of patellar dislocation was in the inferior medial patella and lateral anterior inferior femur. The results suggest that the pattern of bone bruise after ACL rupture and patellar dislocation is completely different. There were 4 kinds of bone bruise patterns after non-contact ACL rupture while there was only 1 kind of bone bruise pattern after patellar dislocation bone bruise patients which was in the inferior medial patella and lateral anterior inferior femur.

Numerous studies have shown that quinolones residues in the foods exceeding the MRL is harmful to the human health. There are some limitations in the existing methods for the residues, so we developed a new limit test method (TLC-SERS) to rapidly determine following residues: enrofloxacin(A), ciprofloxacin (B), ofloxacin(C), fleroxacin(D), sparfloxacin(E), enoxacin(F), gatifloxacin(G) and nadifloxacin(H). The residues can be preliminarily separated by TLC. Labeling the tested compounds’ position on the thin layer plate by their relative Rf under 254nm ultraviolet, and an appropriate amount of nanometer silver solution should be added to the position. The silver on the plate should be irradiated with 532nm laser to obtain SERS of the compounds. The results showed a significant differences of the 8 quinolones’ SERS; the LOD of the H, A, D, E, C, G, F and B were orderly 9.0, 12.6, 8.0, 19.0, 8.0, 8.4, 9.0 and 12.6 ng/mL, and the RSD≤4.9% for SERS of each quinolones.The limit test results of the 20 samples was consistent with that determined by the UPLC–MS/MS. The above results indicate that the TLC-SERS is specific, sensitive, stable, and accurate, providing a new reference for the rapid limit test of harmful residues in foods.

Orthohantaviruses can cause two types of human infections: hemorrhagic fever with renal syndrome (HFRS) and hantavirus pulmonary syndrome (HPS). HFRS is a zoonotic disease transmitted by multiple rodent species. Yunnan Province in southwest China is the natural foci of HFRS, and Dali Prefecture in Yunnan Province has the highest incidence of HFRS; however, the precise status of orthohantavirus infection in Dali Prefecture remains unknown. To this end, we obtained clinical data of HFRS patients from the medical records of the People's Hospital of Xiangyun County in Dali Prefecture from July 2019 to August 2021. We collected epidemiological data of HFRS patients through interviews and investigated host animals using the night clip or night cage method. We systematically performed epidemiological analyses of patients and host animals. The differences in the presence of rodent activity at home (2=8.75, P=0.031&lt;0.05), of rodent-proof equipment in the food (2=9.19, P=0.025&lt;0.05), and of rodents or rodent excrement in the workplace (2=10.35, P=0.014&lt;0.05) were statistically different in the four clinical types, including mild, medium, severe, and critical HFRS-associated diseases. Furthermore, we conducted molecular detection of orthohantavirus in host animals. The total orthohantavirus infection rate of rodents was 2.7% (9/331); the specific infection rate of specific animal species was 6.1% (5/82) for the Apodemus chevrieri, 100% (1/1) for the Rattus nitidus, 3.8% (2/53) for the Rattus norvegicus, and 12.5% (1/8) for the Crocidura dracula. In this study, a total of 21 strains of orthohantavirus were detected in patients and rodents. The 12 orthohantavirus strains from patients showed a closer relationship with Seoul orthohantavirus (SEOOV) L0199, DLR2, and GZRn60 strains; the six orthohantavirus strains from Rattus norvegicus and Apodemus chevrieri were closely related to SEOOV GZRn60 strain; One strains (XYRn163) from Rattus norvegicus and one strain (XYR.nitidus97) from Rattus nitidus were closely related to SEOOV DLR2 strain; the orthohantavirus strain from Crocidura dracula was closely related to the Luxi orthohantavirus (LUXV) LX309 strain. In conclusion, patients with HFRS in Xuangyun County of Dali Prefecture are predominantly affected by SEOOV, with multiple genotypes of orthohantavirus in host animals, and most importantly, these orthohantavirus strains constantly demonstrated zoonotic risk in humans.

Triple-negative breast cancer (TNBC), characterized by deficiency in estrogen receptor (ER), progesterone receptor (PR), and human epidermal growth factor receptor2 (HER2), is among the most lethal subtypes of breast cancer (BC). Nevertheless, the molecular determinants that contribute to its malignant phenotype such as tumor heterogeneity and therapy resistance remain elusive. In this study, we sought to identify the stemness-associated genes involved in TNBC progression. Using bioinformatics approach, we found 55-up and 9-down regulated genes in TNBC. Out of the 55 upregulated genes, a 5 gene-signature (CDK1, EZH2, CCNB1, CCNA2, and AURKA) involved in cell regeneration, was positively correlated with status of tumor hypoxia and clustered with stemness-associated genes, as recognized by Parametric Gene Set Enrichment Analysis (PGSEA). Also, enhanced infiltration of immunosuppressive cells was positively correlated with the expression of these 5 genes. Moreover, our experiments showed that depletion of the transcriptional co-factor nucleus accumbens-associated protein 1 (NAC1), which is highly expressed in TNBC, reduced the expressions of these genes. Thus, the five genes signature identified by this study warrants further exploration as a potential new biomarker of TNBC heterogeneity/stemness characterized by high hypoxia, stemness enrichment, and immune-suppressive tumor microenvironment.

The recent COVID-19 pandemic has caused tremendous damage to social economy and people’s health. Some major issues fighting COVID-19 include early and accurate diagnosis and the shortage of ventilator machines for critical patients. In this work, we propose a closed-loop solution to deal with COVID-19: portable biosensing and wearable photoacoustic imaging for early and accurate diagnosis of infection and magnetically neuromodulation or minimally invasive electrical stimulation to replace the traditional ventilation. Proposed technique can guarantee ubiquitous and onsite detection, and electrical hypoglossal stimulator can be more effective in helping severe patients as well as reducing complications caused by ventilators.

Fullerene molecules are composed of carbon in forms of a hollow sphere, ellipsoid, or tube. Fullerenes have attracted considerable attention in different fields of science since their discovery in 1985. The unique carbon cage structure of fullerene provides immense scope for derivatization, rendering potential for various industrial applications. The prospective applications of fullerenes thus have led to assorted fullerene derivatives. The unique chemical structure also provides ease for fullerene to be synthesized through various kinds of conjugating techniques, where fullerene can be located either on the backbone or the branch chain. Here in this review, we have compiled the toxicity and biosafety aspects of fullerene in aquatic organisms. The frequent use of fullerene is likely to come in contact and interact with the aquatic environment and aquatic organisms. According to the current understanding, waterborne exposure to fullerene-based nanomaterials indeed triggers toxicities at cellular, organic, molecular as well as neurobehavioral levels.

The probiotic bacterial strain Lactobacillus plantarum ZS2058 has been proved to manifest comprehensive functions, which were due to ability to synthesise conjugated fatty acids (CFAs). To investigate the specific functions of CFAs produced by this probiotic bacterium, α-linolenic acid was isomerized by Lactobacillus plantarum strain ZS2058, and two different conjugated α-linolenic acid (CLNA) isomers were successfully isolated. These isoforms, CLNA1 (c9, t11, c15-CLNA, purity 97.48%) and CLNA2 (c9, t11, t15-CLNA, purity 99.00%), both showed the ability to inhibit the growth of three types of colon cancer cells in a time- and concentration-dependent manner. In addition, the expression of MDA in Caco-2 cells was increased by CLNA1 or CLNA2, which indicated lipid peroxidation was related to the antiproliferation activity of CLNAs. Examination of the key protein of pyroptosis showed that CLNA1 induced the cleavage of caspase-1 and gasdermin-D, while CLNA2 induced the cleavage of caspase-4, 5 and gasdermin-D. The addition of relative inhibitors could alleviate the pyroptosis by CLNAs. CLNA1 and CLNA2 showed no effect on caspase-3, 7, 9 and PARP-1, which were key proteins associated with apoptosis. And no sub-diploid apoptotic peak appeared in the result of PI single staining test. In conclusion, CLNA1 activated caspase-1 and induced Caco-2 cell pyroptosis, whereas CLNA2 induced pyroptosis through the caspase-4/5-mediated pathway. The inhibition of Caco-2 cells by the two isomers was not related to apoptosis. This is the first report showing the ability of CLNAs to activate antioxidant defenses resulting in pyroptosis.

Owing to the widespread use of bisphenol analogues (BPs) as bisphenol A (BPA) alternatives, they have been recognized to constitute a health risk for aquatic ecosystems. The occurrence and distribution of six BPs were investigated in the truly dissolved phase (< 5 kDa), colloidal phase (5 kDa to 1 µm) and suspended particulate matter (SPM > 1 µm) in a water diversion project of Nanjing, China. With the exception of bisphenol Z, all BPs were detected in at least two phases, the total concentrations of detected BPs were 161-613 ng/L, 5.19-77.2 ng/L and 47.5-353 ng/g for the truly dissolved phase, colloidal phase and SPM, respectively. Among the detected compounds, BPA still the dominant BPs in the truly dissolved phase and colloidal phase, followed by BPS, while BPAF was the major contaminant in SPM, followed by BPA. The mean contribution proportions of colloids were 1-2 orders of magnitude greater than that of SPM, suggesting that colloids play an important role in regulating the environmental behaviors of BPs. In terms of spatial distribution, although the water diversion project could reduce the pollution levels of BPs, which might further affect the ecological security of the Yangtze River.

Plastics have become an important environmental concern due to their durability and resistance to degradation. Out of all plastic materials, polyesters such as polyethylene terephthalate (PET) are amenable to biological degradation due to the action of microbial polyester hydrolases. The hydrolysis products obtained from PET can thereby be used for the synthesis of novel PET as well as becoming a potential carbon source for microorganisms. In addition, microorganisms and biomass can be used for the synthesis of the constituent monomers of PET from renewable sources. The combination of both biodegradation and biosynthesis would enable a completely circular bio-PET economy beyond the conventional recycling processes. Circular strategies like this could contribute to significantly decrease the environmental impact of our dependence on this polymer. Here we review the efforts made towards turning PET into a viable feedstock for microbial transformations. We highlight current bottlenecks in the degradation of the polymer and the metabolism of the monomers and we showcase fully biological or semisynthetic processes leading to the synthesis of PET from sustainable substrates.

In prostate cancer, p53 maximizes apoptosis in response to severe DNA damage, not DNA replication stress. Here, we examined the apoptotic response of two glioblastoma cells, p53-wild type U87 and a p53-mutated T98G cell, for the same stresses. We ascertained that p53 intensified apoptosis in response to severe DNA damage, not DNA replication stress in glioblastoma. We further asked if p53-mediated apoptosis can be induced by cellular stress other than severe DNA damage. We analyzed two compounds, bortezomib and vorinostat, respective inhibitors of 26S proteasome and histone deacetylase, to evaluate their capacity to activate p53-mediated apoptosis. The cellular stress incited by bortezomib, not vorinostat, activated p53-mediated apoptosis. Next, we asked if the cellular stress generated by combining the two compounds had a synergistic effect on apoptosis. Our results demonstrated that doxorubicin with bortezomib or CFS-1686, or bortezomib with vorinostat have a significant synergistic effect on apoptosis only in p53-wild type cell. Under high stress, p53 translocates from cytosol into the nucleus to cause apoptosis possibly. Together, p53 maximizes apoptosis for cellular stress caused by severe DNA damage, disruption of protein turnover, and for the stress induced by drug combination including doxorubicin with bortezomib or CFS-1686, and bortezomib with vorinostat.