An ultra-low anti-reflection optical coating on both surfaces of a plastic cover slip was studied for use in confocal image measurement. The optical reflectance at a wavelength of 632.8 nm was less than 0.1% when the coated sample was placed in a liquid having a refractive index of 1.34 close to the aqueous solution of the biomaterial. The high- and low-index coating films, Substance-2 (PrTiO3) and silicon dioxide (SiO2), were measured by an ellipsometer to determine their optical refraction indices and extinction coefficients. Theoretically, when the two layer thicknesses are designed using the optical admittance diagram of the cover slip to approach the equivalent index of 1.34, a reflectance of 1.6×10-5% in the liquid could be obtained. Experimentally, the reflectance of the sample deposited on the two faces of the cover slip was 4.223±0.145% as measured in the air; and 0.050±0.002% as measured by a He-Ne laser in the liquid.

Infertility affects approximately 15% of couples worldwide, an estimated 30% of which is related to male factor infertility. Application of low level laser therapy (LLLT) to improve fertility status is a rapidly growing discipline in medicine. Laser therapy triggers a variety of biological processes through interaction with primary cellular photoacceptors. The present review aims at evaluating the literature available in the MEDLINE/ PubMed on cellular and molecular mechanisms of photobiomodulation in the domains of reproductive and veterinary medicine. We primarily focused on the clinical application of laser treatment on seminal quality, in particular its role in promoting spermatozoa motility, as well as the role of phototherapy in modulating assisted reproduction (ART). Additionally, we investigated the strength of evidence in support of the positive impact of photobiomodulation on facilitating ART.

This study evaluated the effect of low-level laser irradiation induces by diode laser on the speed of orthodontic tooth movement of canines submitted to initial retraction. Twenty-four mandibular canines were retracted by using NiTi spring (force of 150 g/side). Thirteen of those were irradiated with a diode laser 980-nm diode laser (Wiser Laser Doctor Smile, Lambda) operating at an 810-nm wavelength (1 W of output power, continuous wave of 66.7 J/cm2) that was equipped with a 0.6-mm optical fiber in continuous-wave mode. The canine retraction was accomplished by using prefabricated coil springs. The right of the mandible was chosen to be irradiated with the laser, whereas the left side was considered the control without laser irradiation. The laser was applied with 0-, 3-, 7-, and 14-day intervals. The amount of canine retraction was measured with a digital electronic caliper while the pain level was prompted by a patient questionnaire. The speed of tooth movement was significantly greater in the laser group than in the control group. The pain intensity was also at a lower level in the laser group. Our findings suggest that diode laser therapy can highly accelerate tooth movement during orthodontic treatment and can also effectively reduce pain level.

Background: The prevalence of atopic dermatitis in domestic animals is one of the problems of modern veterinary. Treating with standard techniques using chemotherapeutic agents not always leads to a positive result of therapy; moreover, many drugs produce adverse side effects. Methods: Low level laser therapy, in particular, intravenous laser blood illumination (ILBI) has a pronounced and long-lasting impact on the immune system of animals. The combined technique including ILBI-635 (635 nm, 2 mW, 5 min) and LUVBI^® (365 nm, 2 mW, 3 min) every other day provides a positive change in clinical status of cats with allergic dermatitis after the 3rd-4th treatment session. Results: The increased level of erythrocytes and hemoglobin was identified in the course of treatment, and it indirectly indicates increased blood transport activity, which improves trophic provision and microcirculation. A double reduction of leukocytes and a significant decrease of neutrophil cells indicate the immunomodulatory effect of LILI (low-intensity laser illumination). The increase in the percentage of lymphocytes and the decrease of eosinophils and monocytes against the background of basophil concentrations deviations within physiological concentration result in the reduction of inflammatory mediators expression that induce itching. The reduction of total IgE concentration 32 times against control on the 7th day of treatment correlates with the decrease in the quantitative content of peripheral blood eosinophils, indicating the decrease in severity of an allergic process. Conclusion: LLLT is recommended against the background of standard drug therapy to achieve quick clinical outcome together with a long-lasting prolonged effect.

This study aimed to evaluate the proliferation and migration of fibroblast cells derived from chronic wounds and investigate the impact of low-level laser therapy (LLLT) on their growth and migration. A total of 60 dermal samples were obtained from three sites of chronic pressure ulcers and diabetic ulcers in 20 patients. Following collection in the operating room, the dermal samples were isolated using the procedure described by Freshney RI. Fibroblasts from the wound base (Site 1) exhibited a slow proliferation rate and a decrease in proliferative capacity. Fibroblasts from wound margins (Site 2) and adjacent healing skin (Site 3) could be successfully isolated and maintained for multiple generations without any morphological changes. Fibroblasts from chronic wounds at Sites 2 and 3 showed slower proliferation rates and reduced migration capabilities compared to normal dermal fibroblasts (control samples). The fibroblast cells were exposed to LLLT at different energy levels (2.5, 3, and 3.5 J/cm2). The laser-treated groups demonstrated a significantly higher increase in cell count compared to the control sample, with the highest increase observed at an energy level of 3 J/cm2. These findings suggest that LLLT at an energy level of 3 J/cm2 could effectively enhance fibroblast migration, indicating its potential as a therapeutic intervention for chronic wounds.

Background: Low-level (LLLT) and high-intensity laser therapy (HILT) can be beneficial additions to knee osteoarthritis (KOA) rehabilitation exercises; however, it is still being determined which modality is more effective. Aim: To compare the effects of LLLT and HILT as adjuncts to rehabilitation exercise (LL+EX and HL+EX) on clinical outcomes in KOA. Methods: Thirty-four adults with mild to moderate KOA were randomly allocated to either LL+EX (n = 17) or HL+EX (n = 17) groups. All participants underwent their designated laser treatment combined with rehabilitation exercises weekly for twelve consecutive weeks. The Knee Injury and Osteoarthritis Outcome Score (KOOS), Numerical Pain Rating Scale (NPRS), active knee flexion, and Timed Up-and-Go test (TUG) were assessed at baseline and immediately post-intervention. Results: Post-intervention, both groups significantly improved their KOOS, NPRS, active knee flexion, and TUG scores compared to baseline (p < 0.01). The mean difference of change in KOOS, NPRS, and active knee flexion scores for the HL+EX group surpassed the minimal clinically important difference threshold. In contrast, the LL+EX group only demonstrated clinical significance in NPRS scores. Conclusions: Incorporating HILT as an adjunct to usual KOA rehabilitation led to significantly higher improvements in pain, physical function, and knee-related disability compared to LLLT.

Background:This study evaluated the effect of low-level laser therapy on postoperative pain and wound healing in children undergoing primary molar extractions.Methods:40children,6-10years of age, systemically healthy, and had atraumatic extraction indications of bilateral primary molar teeth were included in the study. First session randomly selected tooth was extracted under local anesthesia. In the control group, only the clot formation on the socket was observed and photographed. Other group extraction's performed 2weeks later. The LLLT group treated with980nm wavelength Doctor Smile Wiser diode laser and photographed. Non-epithelialized surface measurements performed with the ImageJ program. Pain assessment was performed with Wong-Baker Pain Scale. Statistical analyzes were performed with SPSS software.Results: There was no statistically significant difference in Wong-Baker values(p>0.05). The laser group had more '0' values on days 1 and7; same values as the control group were recorded on other days. In soft tissue healing 3rd day evaluations, non-epithelialized surface of laser socket was found to be smaller than control group, and measurement results were found to be statistically significant(p<0.05). The other days' measurement results were not statistically significant(p>0.05).Conclusions:Although LLLT not found to be very effective in reducing postoperative discomfort after extraction of primary molars, it provides better wound healing in extraction sockets.

Our hypothesis that controlled ozone applications interfere into the redox balance of the biological organism (first published in 1998 with a preclinical trial on protecting the liver from CCl4 intoxication), has been verified over the last 2 decades in reactive oxygen species (ROS)-induced mitochondrial pathologies, such as rheumatoid arthritis, osteoarthritis, aging processes, diabetes-2 and in prevention of intoxications. Low-dose ozone acts as a redox bioregulator: The restoration of the disturbed redox balance is comprehensible in a number of preclinical and clinical studies by a remarkable increase of the antioxidant repair markers, here mainly shown as glutathione increase and a reduction in oxidative stress markers, mainly malondialdehyde. The mechanism of action is shown, relevant data are displayed, evaluated and comprehensively discussed: The repair side of the equilibrium increases by 21% up to 140% compared to the non-ozone treated groups and depending on the indication; the stress markers are simultaneously reduced, the redox system regains its balance.

Infrared and visible light image fusion technology integrates image feature information from two different modalities to generate an image that integrates complementary information from the source images. However, in low-light scenarios, the degradation of lighting in visible light images leads to existing fusion methods being unable to effectively extract texture detail information from the scene. At this time, the target prominence information provided by infrared images alone is far from sufficient. To address this challenge, this paper proposes a lightweight infrared and visible light image fusion method based on low-light enhancement, named LLE-Fuse. Firstly, the method improves the MobileOne Block by embedding the Sobel operator in the Edge-MobileOne Block to perform feature extraction and downsampling on the source images. Then, intermediate features of different scales are obtained and fused through a cross-modal attention fusion module, followed by image reconstruction using a decoder with upsampling. Next, the CLAHE algorithm is used for image enhancement of infrared and visible light images, and the enhanced loss guides the network model to learn the capability of low-light enhancement. Finally, upon completion of the network training, the method optimizes the Edge-MobileOne Block into the direct connection structure of MobileNetV1 through structural re-parameterization, effectively reducing the computational resource consumption of the model network. Through extensive experimental comparisons, this paper's method demonstrates excellent performance in both visual appeal and evaluation metrics, providing satisfactory fusion results even in low-light scenarios.

In this study, we explore the potential of using a straightforward neural network inspired by the retina model to efficiently restore low-light images. The retina model imitates the neurophysiological principles and dynamics of various optical neurons. Our proposed neural network model reduces the computational overhead compared to traditional signal-processing models while achieving results similar to complex deep learning models from a subjective perceptual perspective. By directly simulating retinal neuron functionalities with neural networks, we not only avoid manual parameter optimization but also lay the groundwork for constructing artificial versions of specific neurobiological organizations.

Objective: We report a case of acute pancytopenia and liver injury after concomitant administration of low-dose methotrexate (MTX), and high-dose esomeprazole and metamizole. Case summary: A 71-year-old patient with chronic systemic idiopathic erosive arthritis was admitted after a pelvic ring fracture. After hospital admission, she received MTX in addition to esomeprazole and metamizole. Subsequent laboratory tests revealed pancytopenia and elevated liver enzymes. The follow-up clinical examinations were unremarkable, with the exception of sub-febrile temperatures. Further investigations did not detect a definitive etiology. Due to the suspicion of methotrexate-induced hematotoxicity and hepatotoxicity, antagonizing therapy with calcium folinate was administered, after which the blood counts and liver parameters normalized. Discussion: Due to the administration of high-dose metamizole immediately before the administration of low-dose MTX, the pre-existing hematotoxic pharmacodynamic effect of MTX was acutely enhanced by that of metamizole, although folic acid was administered preemptively. In addition, the concomitant administration of high-dose esomeprazole and normal dose torasemide resulted in a pharmacokinetic interaction with MTX by decreasing its renal secretion and elimination, further enhancing the concentration-dependent hematotoxic and hepatotoxic side effects of MTX. Conclusions: The relatively high demand for analgesics in patients with chronic rheumatic diseases already being treated with MTX and proton pump inhibitors necessitates that clinicians consider drug-drug interactions as potential causes of adverse drug reactions after the administration of metamizole or nonsteroidal anti-inflammatory drugs. In this category of patients, it is strongly recommended to switch to analgesics of other classes.

With the advent of deep learning, significant progress has been made in low-light image enhancement methods. However, deep learning requires enormous paired training data, which is challenging to capture in real-world scenarios.To address this limitation, this paper presents a novel unsupervised low-light image enhancement method, which first introduces the frequency domain features of images in low-light image enhancement tasks. Our work is inspired by imagining a digital image as a spatially varying metaphoric “field of light”, then subjecting the influence of physical processes such as diffraction and coherent detection back onto the original image space via a frequency-domain to spatial-domain transformation (inverse Fourier transform). However, the mathematical model created by this physical process still requires complex manual tuning of the parameters for different scene conditions to achieve the best adjustment. Therefore, we proposed a dual-branch convolution network to estimate pixel-wise and high-order spatial interactions for dynamic range adjustment of the frequency feature of the given low-light image. Guided by the frequency feature from the “field of light” and parameter estimation networks, our method enables dynamic enhancement of low-light images. Extensive experiments have shown that our method performs well compared to state-of-the-art unsupervised, and its performance approximates the level of the state-of-the-art supervised methods qualitatively and quantitatively. At the same time, the light network structure design allows the proposed method to have an extremely fast inference speed(nearly 150 FPS on an NVIDIA 3090 Ti GPU for an image of size 600×400×3 ). Furthermore, the potential benefits of our method to object detection in the dark are discussed.

Several Lung diseases can result in lung damage structural changes, with lung transplantation as a only therapeutic option when the disease reaches an advanced progression, unfortunately, the success of lung transplantation is limited. In this context, lung bioengineering is considered a potential therapeutic alternative and the current approach is based on the use of the natural extracellular matrix (ECM) of the decellularized lung. The use of undifferentiated cells to seed an ECM can be a more practical strategy for lung bioengineering but the sterilization of the organ for this recellularization process is still a challenge. In this sense, Low-Level Laser Therapy (LLLT) can emerge as a potential treatment alternative. Therefore, the objective of this study was to verify if LLLT, can optimize lung recelularization with mesenchymal stem cells by cytokine modulation. For this, we decellularized lungs from C57BL/6 mice perfusing SDS 1% via pulmonary artery, sterilized with LLL (660nm, 100mW, 30s). Whole lung scaffolds were recellularized: (1) Recellularized Lung (2) Recellularized Lung + LLLT. Mesenchymal stem cells derived from human tooth pulp (DPSc) were seeded into lungs and incubated for 24 hours at 37ºC, 5% CO₂, in a bioreactor-like conditions, maintaining CPAP at 20cmH2O, 90% O2, and LLL at wavelength of 808nm, 100mW, 30s. Culture medium were analyzed at 24 hours. H&E, immunostaining, SEM and ELISA assay were performed. We produced viable biological scaffolds absent of DNA content, preserving glycosaminoglycans and collagen I, III and IV, fibronectin, laminin and elastin and lung structure (SEM). The levels of IL-6 and IL-8 were stable during the 24 hours of culture. IFN-γ levels showed significant difference in the DPSc and DPSc+LLLT group in the 24-hour evaluation. The levels of IL-10 decreased after LLLT. These findings highlight LLLT's role in cytokine regulation and contamination prevention during lung recellularization with mesenchymal stem cells. Overall, these results demonstrated that LLLT's modulated cytokine levels and could prevent contamination during the lung recellularization process with mesenchymal stem cells, offering promise for enhanced therapeutic strategies in lung bioengineering.

In recent years, researches on combining wavelet decomposition and convolutional neural network (CNN) together to classify hyperspectral images (HSI) have emerged, and some effective classification models have been proposed and achieved good classification results. However, there are two problems for most of the proposed models. One is the heavy training parameters and the other is that there is no distinction between the classification effectiveness of low frequency and high frequency features after wavelet decomposition. In this paper, a new light-weighted HSI classification model (LLFWCNN) is proposed, which performs multi-layer wavelet decomposition for HSI after dimensionality reduction, and only arranges the low frequency features in a specific stack mode, then classifies them through a well-designed convolutional neural network. Compared with other classification models, the number of parameters is only 2.5% of that of other models. And only the low frequency features after wavelet decomposition are used, while the high frequency features are abandoned. The results showed that compared with the state-of-the-art classification models, LLFWCNN could obtain the same or even better classification results with fewer network parameters and proved that the low frequency features after wavelet decomposition provide LLFWCNN with more favorable information for HSI classification as well.

This study aims to evaluate the effectiveness of inactivating Salmonella enteritidis in fresh chicken breast by irradiation using a combination of short-wave UV (0, 3, 6, 9, 12 and 15 J / cm2) and a natural antimicrobial such as caffeine (0, 5, 10, 15 and 20 nM/g) as alternative proposals to conventional techniques to reduce pathogens in food. The temperatures used were from 2 to 22°C. The most suitable models were double Weibull in 60% of cases with an adjustment of R2 0.9903-0.9553 and Weibull + cola, in 46.67%, with an adjustment of R2 of 0.9998-0.9981. Noting that the most effective combination in the reduction of Salmonella was 12 J/cm2 of UV light and 15 nM/g of caffeine, with a reduction of 6 CFU/g and an inactivation rate of 0.72. The synergistic effect was observed by increasing caffeine and UV light. Furthermore, the physic-chemical characteristics of the food matrix were not affected by the combination of both technologies. Therefore, these results suggest that this combination can be used in the food industry to effectively inactivate Salmonella enteritidis, without deteriorating product quality.

Fluorescence microscopy is an important tool for disease diagnosis, often requiring costly optical components, such as fluorescence filter cubes and high-power light sources. Due to its high cost, conventional fluorescence microscopy cannot be fully exploited in low-income settings. Smartphone-based fluorescence microscopy becomes an interesting low-cost alternative, but raises challenges in the optical system. We present the development of a low-cost inverted laser fluorescence microscope, that uses a smartphone to visualize the fluorescence image of biological samples. Our fluorescence microscope uses a laser-based simplified optical filter system, that provides analog optical filtering capabilities of a fluorescence filter cube. Firstly, we validated our inverted optical filtering by visualizing microbeads labeled with three different fluorescent compounds or fluorophores, commonly used for disease diagnosis. Secondly, we validated the disease diagnosis capabilities, by comparing the results of our device with those of a commercial fluorescence microscope. We successfully detected and visualized Trypanosoma cruzi parasites, responsible of the Chagas infectious disease, and the presence of Antineutrophil cytoplasmic antibodies of the ANCA non-communicable autoimmune disease. The samples were labeled with the fluorescein isothiocyanate (FITC) fluorophore, one of the most commonly used for disease diagnosis. Our device provides a 400 X magnification and is at least two orders magnitude cheaper than conventional commercial fluorescence microscopes.

In this letter, we show an alternative low-cost fabrication method to obtain poly(dimethyl siloxane) (PDMS) microfluidic devices. The proposed method allows the inscription of micron resolution channels on polystyrene (PS) surfaces, used as a mold for the wanted microchip’s production, by applying a high absorption coating film on the PS surface to ablate it with a focused low-power visible laser. The method allows obtaining micro resolution channels at powers between 2 and 10mW and can realize any two-dimensional polymeric devices. The effect of the main processing parameters on the channel’s geometry is presented.

This paper investigates the use of contactless power ultrasonic excitation to decrease the electrical impedance of the weld in laser welding. The literature extensively documents the impact of em-ploying contact power ultrasonic excitation on the microstructure morphology and refinement of grain in the weld. This study involves characterizing an industrial High Power Ultrasound Transducer (HPUT) by determining the optimal distance and angle for contactless excitation of the fusion zone in the weld, aiming to achieve the maximum amplitude. Subsequently, the transducer is integrated into the laser welding system, resulting in the creation of an ultrasonic-assisted welding system. To find the improvement due to the contactless vibration assistance, the welding area was char-acterised by an impedance ohmmeter device. The results indicate an approximately 6 % im-provement in the welding quality in terms of the impedance value, an important parameter for battery pack welding. In response to the issue of overheating in the industrial transducer during prolonged welding operations, an alternative transducer was proposed to overcome this challenge. Further investigations are carried out by the alternative transducer to find the effect of different wave types, namely, shear and compressional waves, on the welding quality. The contact vibration can excite the plate approximately 50 times higher in acceleration amplitude than contactless ex-citation. Nevertheless, enhancements of 10% and 6% are observed in the impedance value when utilising compressional and shear waves, respectively, as compared to the results obtained with contactless vibration.

In table tennis competitions the rule violation judgment with the greatest controversy is the height of the ball serve. This is because inaccuracy in the ball height judgment, which results in erroneous judgment, is unavoidable. Thus, we designed an automatic image judgment auxiliary system for table tennis ball height during service in this study. We used a high-speed camera to record the ball toss in the table tennis service. The designed algorithm architecture can automatically search for the ball and the position of the hand action under low light source conditions. The algorithm is mainly divided into hue-saturation-value color space processing and morphology processing using Hough transform to search for the circular ball. Experiment result shows that color segmentation can successfully and accurately determine the ball position under low light conditions. The morphology method can find the position of the hand and help determine the moment when the ball leaves the hand during the service ball toss. Finally, the actual size of the target is used to estimate the actual distance unit represented by the image pixel.

Optimum design and accurate control of the internal structure of the laser target materials remain an important goal for various laser physics experiments, especially for generating high flux photon and neutron beams. The low-density material is considered to be one of the most difficult for X-ray study due to its high transparency and imperceptible contrast. To produce clear visualization of foam containing sparse structures we used a high-quality monochromatic X-ray beam of synchrotron radiation source PETRA-III at DESY. The X-ray beam parameters allow tomographic scanning with application of phase contrast retrieval algorithms. A series of 3D images of foam-suspended glass microsphere inside the plastic cylinder were obtained with the quality high enough to observe the internal structure and to visualize uniformity, displacement and surface roughness on both sides of the microsphere. The main object under investigation was a CH-plastic capillary including 10 mg/cc CHO-foam with the centered glass microsphere. The results of this work demonstrate that tomographic visualization based on a high quality X-ray radiation and phase contrast analysis is an effective and useful technique for development of new laser targets containing structured low density materials.

It is well known that the effect of laser irradiation on the blood causes a change in the shape of red blood cells and an increase in their activity, especially in low-level laser therapy (LLLT). The aim of this study was to identify the ability of erythrocytes to deform when exposed to a blue laser.24 laboratory rats were exposed to blue laser in the gingival region of the lower jaw daily for 5 minutes over 3 days. The blue laser possessed a power of 0.5 W and was operated using a con-tactless approach, the dynamic technique in continuous wave mode, and an uninitiated fiber. A blood sample was taken from the lateral vein of the tail before the LLLT, on the first, second, third, and fifth days. The samples were stained, and cytometry was conducted. The exposure to blue laser caused a significant increase in the number of dome-shaped deformable erythrocytes in the blood of laboratory rats (p

Low back pain (LBP) is a leading cause of disability. It significantly impacts the patient’s quality of life, limits their daily living activities, and reduces work productivity. To reduce the burden of LBP, several pharmacological and non-pharmacological treatment options are available. This review summarizes the role of heat therapy in the management of LBP. First, we outline the common causes of LBP, then discuss the general mechanisms of heat therapy on (LB)P, and finally review the published evidence regarding the impact of heat therapy in patients with acute or chronic non-specific LBP. This review demonstrates that continuous, low-level heat therapy provides pain relief, improves muscular strength, and increases flexibility. Therefore, this effective, safe, easy-to-use, and cost-effective non-pharmacological pain relief option is still relevant in modern clinical practice.

This article introduces a novel payload structure, which has been experimentally proven to have smaller impact force while the carried internal electronics remains intact. The study describes in details how materials and geometric structures were chosen based on information analysis. It is clarified how possible geometric structures and materials can be chosen to yield optimal efficiency. Finite element method simulations were carried out to investigate the mechanical properties of several geometric structures, which has led to the dodecahedron form. For the frame, Polylactic Acid were chosen as an optimal material. A low air pressure test for parts of the structure, and also the whole structure were carried out with successful results. Drop tests, with force measuring sensors and high speed videos, were carried out for measuring and comparing the maximal impact force of classical payloads and the novel one. Laboratory and real life tests demonstrated that the developed new structure is safer and it is applicable.

Abstract: High power semiconductor laser is a kind of photoelectric device with high efficiency and high stability, the performance of its drive system directly affects its output characteristics and service life. In order to solve the problems of stability and robustness of the output power of semiconductor laser, a semiconductor laser driving power supply with high efficiency, low ripple and strong anti-interference ability was developed. The power supply adopts full-bridge LCC resonant power topology. Firstly, a mathematical model is established to analyze the relationship between LCC resonator parameters and output current gain. Secondly, a LCC resonator parameter design method is proposed to reduce the current stress of components, and the variable frequency phase shift (PFM-PWM) composite control strategy and linear active disturbance rejection control (LADRC) algorithm are proposed, which not only ensures the zero voltage (ZVS) conduction of MOS tube, but also reduces the on-off loss of MOS tube. Improved power efficiency and suppressed output current ripple; At the same time, the instability of the output current is ensured due to the input voltage, load and parasitic parameter change of the circuit. Finally, the simulation and experimental results show that the power supply can be continuously adjustable in the output current range of 0-40A, the current ripple is less than 0.8%, and the working efficiency is up to 92%. It has the characteristics of high stability, small ripple, high efficiency, low cost and good robustness.

Background: Chronic non-specific low back pain (CNSLBP) is defined as back pain that lasts longer than 12 weeks. Objectives: To investigate the efficacy of manual therapy (MT) program combined with Capacitive and Resistive Electric Transfer (TECAR) therapy in individuals with CNSLBP. Method: Sixty adults with CNSLBP were randomly equally divided into three groups. The first group followed an MT protocol in the lumbar region (MT group), the second group followed the same MT protocol combined with TECAR therapy (MT + TECAR group) using a conventional capacitive electrode as well as a special resistive electrode bracelet and the third group (Control group) received no treatment. Both intervention programs included six treatments over two weeks. Pain in the last 24 hours with the Numeric Pain Rating Scale (NPRS), functional ability with the Roland-Morris Disability Questionnaire (RMDQ), Pressure Pain Threshold (PPT) in the lumbar region with pressure algometry, and mobility of the lumbo-pelvic region through fingertip-to-floor distance (FFD) test were evaluated before and after the intervention period with a one-month follow-up. Analysis of variance with repeated measures was applied. Results: In the NPRS score, both intervention groups showed statistically significant differences compared to the control group both in the second week as well as in the one-month follow-up (p < .001). Between-groups differences were also noticed between the two intervention groups in the second week (p < .05). Differences in the RMDQ score in the second week and on the one-month follow-up were detected between the intervention groups and the control group (p < .001), while differences between the two intervention groups were only detected in the one-month follow-up (p < .001). Regarding the PPT values, differences were found mainly between the MT + TECAR and the control group and between the MT + TECAR and the MT group (p < .05), with the MT + TECAR group in most cases showing the greatest improvement compared to the other two groups, which remained statistically significant in the one-month follow-up (p < .05). Finally, both intervention groups improved the mobility of the lumbo-pelvic region in both time points compared to the control group without, however, statistically significant differences between them (p> .05). Conclusion: The application of an MT protocol with TECAR therapy appeared more effective than conventional MT as well as compared to the control group in reducing pain and disability and improving PPT in individuals with CNSLBP. No further improvement was noted in mobility of the lumbo-pelvic region by adding TECAR to the MT intervention.

This Dataset reports the clinical information and measurements of 231 patients who underwent multifrequency low-level laser-assisted mastopexy. The Dataset was collected between February 2021 and November 2023. These data were used to assess the effect of this procedure on breast ptosis degree and the nipple to sternal notch distance to know the evolution of breast ptosis. This article presents demographic, personal and familial history, anthropometric measurements, pto-sis degree according to the Regnault system, Nipple-to-Sternal Notch distance (SNND), and complications according to the Clavien-Dindo System. The collected data were in English, and the responses were anonymised to ensure the Colombian legal framework. The data were stored in a .csv file.

The orthodontic treatment brings numerous benefits and, in most cases, the benefits outweigh the possible disadvantages. Root resorption (RR) is a common adverse phenomenon associated with orthodontic treatment. This study evaluates the role of low-level laser emission / Photobiomodu-lation (LE/P) in quantitative measurements of root resorption (QRR). The application of LE/P was done after each orthodontic activation with 4 types of treatment intervention (TI) on the RR after fixed orthodontic treatment (FOT) of the upper arch with ectopic eye tooth/teeth [EET]. 32 Orthodontic patients scheduled for FOT were selected and assigned to the 4 groups. These were LE/P+Self ligating bracket (SLB), LE/P+Conventional bracket (CB), Non-Photobiomodulation (non-LE/P)+SLB, and non-LE/P+CB. Standard management stages of FOT were followed in the maxilla. Each patient received a single application of LE/P labially/buccally and palatally, a total of 5 different points during each activation or appointment. The main outcome measure was QRR in maxillary anteriors before and after FOT assessed via cone-beam computed tomography (CBCT) using 3D OnDemand software. Insignificant QRR was found between before and after FOT in SLB, CLB, and LE/P, non-LE/P groups (p > 0.05). QRR in the SLB vs CB and LE/P vs non-LE/P group was significantly different in 11, 13, and 23 (p < 0.05). QRR in the LE/P+SLB group (p < 0.05) was significantly different in 11, 13, and 23 than that in the other groups. The most severe QRR was found on the 13 (0.88 ± 0.28mm and 0.87±0.27mm) and 23 (1.19 ± 0.14 mm and 1.16±0.13mm) in the CB and non-LE/P group (p < 0.001). LE/P+SLB showed highly significant superior outcome (p < 0.001) in relation to non-LE/P+CB, the QRR of 23 were 0.813± 0.114mm and 1.156± 0.166mm respectively. Significantly higher amount of QRR found in EET patients after FOT treated with the CB, non-LE/P, and non-LE/P+CB system and warrants further investigation to explore potential specific causes.

Nowadays, the uses of laser and optics in the medical areas are extremely vivid, especially low-level laser therapy. The light with the wavelength of 633 nm to 1200 nm could penetrate and propagate deep in biological tissue. To develop the low-level laser therapy device, optimizing light delivery is critical to accurately stimulate the biological effects inside the biological tissue. Nevertheless, each form of the tissues at each zone on the body had various refractive optic, absorption, scattering, and anisotropy coefficients. This paper describes the simulation results of low-level laser propagation from skin surface at the lower spine, the knee, the femur and the prostate gland with four wavelengths (633 nm, 780 nm, 850 nm, and 940 nm) by the Monte Carlo method. These simulation results are the base for developing the low-level laser therapy device, that could be used in clinical for treating the fracture, knee osteoarthritis, spinal degeneration, and benign prostatic hypertrophy.

Knowledge of the temperature evolution is crucial to understand and control laser beam welding of low-melting materials. Existing temperature determination approaches are restricted to i) one-dimensional temperature information (e.g. ratio-pyrometers), ii) a priori knowledge of the emissivity (e.g. thermography) and iii) high temperature regions (e.g. two-wavelength imaging). In this paper, a ratio-based two-color-thermography approach is developed that allows for two-dimensional temperature determination in low-melting temperature ranges (< 1200 K). For static measurement situations it is demonstrated, that temperature can be determined despite variation in signal intensity and emissivity with high accuracy. The two-color-thermography set-up is further transferred into a commercial laser beam welding machine and experiments are conducted for varying process parameters. The direct application of the developed two-color-thermography system in dynamic process situations is limited as image artifacts presumably caused by internal reflections inside the optical beam path are present.

This study investigated the roles of low-molecular-weight fucoidan (LMWF) in enhancing the anti-cancer effects of fluoropyrimidine-based chemotherapy. HCT116 and Caco-2 cells were treated with LMWF and 5-FU. Cell viability, cell cycle, apoptosis, and migration were analyzed in both cell types. Potential mechanisms underlying how LMWF enhances the anti-cancer effects of fluoropyrimidine-based chemotherapy were also explored. The cell viability of HCT116 and Caco-2 cells was significantly reduced after treatment with a LMWF-5-FU combination. In HCT116 cells, LMWF enhanced the suppressive effects of 5-FU on cell viability through the 1) induction of cell cycle arrest in the S phase and 2) late apoptosis mediated by the Jun-N-terminal kinase (JNK) signaling pathway. In Caco-2 cells, LMWF enhanced the suppressive effects of 5-FU on cell viability through both c-mesenchymal–epithelial transition (MET)/ Kirsten Rat Sarcoma virus (KRAS)/ extracellular signal-regulated kinase (ERK) and c-MET/ phosphatidyl-inositol 3-kinases (PI3K)/ protein kinase B (AKT) signaling pathways. Moreover, LMWF enhanced the suppressive effects of 5-FU on tumor cell migration through the c-MET/ matrix metalloproteinase (MMP)-2 signaling pathway in both HCT116 and Caco-2 cells. Our results demonstrated that LMWF is a potential complementary therapy for enhancing the efficacies of fluoropyrimidine-based chemotherapy in colorectal cancers (CRCs) with the wild-type or mutated KRAS gene through different mechanisms. However, in vivo studies and in clinical trials are required to validate the results of the present study.

The trafficking of illegal drugs by criminal networks at borders, harbors, or airports is an increasing issue in public health as these routes ensure the main supply of illegal drugs. The prevention of drug smuggling, including the installation of scanners and other analytical devices to detect ultra-small traces of drugs within a reasonable time frame, remains a challenge. The presented immunosensor is based on a monolithic affinity column with a large excess of immobilized hapten, which traps fluorescently labeled antibodies as long as the analyte cocaine is absent. In the presence of the drug, some binding sites of the antibody will be blocked, which leads to an immediate breakthrough of the labeled protein, detectable by highly sensitive laser-induced fluorescence with the help of a Peltier-cooled complementary metal-oxide-semiconductor (CMOS) camera. Liquid handling is performed with high-precision syringe pumps and microfluidic chip-based mixing devices and flow cells. The biosensor achieved limits of detection of 23 pM (7 ppt) of cocaine with a response time of 90 seconds and a total assay time below 3 minutes. With surface wipe sampling, the biosensor was able to detect 300 pg of cocaine. This immunosensor belongs to the most sensitive and fastest detectors for cocaine and offers near-continuous analyte measurement.

Low back pain (LBP) is a pandemic and costly musculoskeletal condition in the United States. Patients with LBP may endure surgery, injections, and expensive visits to emergency departments. Some suggest that using physical therapy or chiropractic in the earlier stage of LBP reduces the utilization of expensive health services and lowers the treatment costs. Nevertheless, there is no consistent evidence to declare which one of these methods is a cost-effective treatment within a short (less than a year) period of time. The purpose of this study was to investigate the cost-effectiveness of chiropractic versus physical therapy in the United States. A decision tree analytic model was used for estimating the economic outcomes. The findings showed that in the chiropractic group, the total average cost was $48.56 lower than the physical therapy group, and daily adjusted life years (DALY) was 0.0043 higher than the physical therapy group. Chiropractic care was shown to be a cost-effective alternative compared with physical therapy for adults with at least three weeks of low back pain over six months.

This research proposes a roof-mounted auxiliary power supply (APS) system for 600VDC low-floor light rail vehicle (LRV). The proposed APS system consists of five parallel-connected dc-ac inverter modules (modules 1-5). The inverter modules 1 and 2 are three-phase dc-ac inverters for compressor motors of the cooling system, and the inverter modules 3 and 4 are three-phase dc-ac inverters for air pump motors of the braking system. The inverter module 5 is single-phase dc-ac inverter for 220VAC power supply for onboard electric loads. Simulations and experiments were carried out under variable load torque and output frequency for modules 1 – 4; and under full and no resistive loads for the inverter module 5. The measured total input current and total input power of the proposed APS system under full load condition are 118.76A and 71.25kW. Essentially, the proposed APS system is operationally applicable to the 600VDC low-floor RLV. Besides, the novelty of this research lies in the use of five parallel-connected inverter modules, unlike in the conventional APS systems which require three-phase output transformer or isolated dc-dc converter. Specifically, the proposed APS system requires neither three-phase output transformer nor isolated dc-dc converter.

This study aimed to evaluate the early-childhood comorbidities of cerebral palsy (CP) in children with low birth weight (LBW) and assess the impact of maternal bio-psychosocial factors on the risk of CP in preterm infants across varying birth weights. Data for 15,181 prematurely born infants from 2009 to 2013 and 151,810 matched controls from Taiwan's National Health Insurance Research Database were analyzed. Period prevalence of CP, and comorbidities of LBW were verified, and odds ratios (ORs) were calculated. Results confirmed that increasing prematurity and low birth weight (LBW) rates in Taiwan. LBW was associated with higher CP prevalence. Maternal age extremes (&lt;20 and &gt;40 years) were significant risk factors of CP in LBW infants. LBW infants showed higher risks of respiratory, circulatory, and nervous system and psycho-developmental comorbidities compared to controls. Infants with the lowest birth weights had even higher ORs for these comorbidities. However, gastrointestinal and nutritional comorbidities were less prevalent in premature infants. Maternal factors such as family income, number of hospital admissions, and length of hospital stay were significantly correlated with birth weight and subsequent complications. Each additional gestational week significantly reduced the risk of complications in premature infants. Additionally, maternal bio-psychosocial factors were associated with birth weight and related outcomes in premature infants, emphasizing the importance of addressing these factors in prenatal care and interventions.

This paper investigates if the polar groups induced by a plasma treatment can increase the lap shear strength of laser joined metal and plastic hybrids. Optimal laser joining parameters for cold-rolled AISI304 – Polyamide 6.6 and sandblasted AISI304 - Polypropylene hybrids are developed. The OWRK-method was utilized to identify the change in surface free energy of a low-pressure plasma treatment. Plasma treated samples were joined and tested. The fractured surfaces were investigated via light microscopy and SEM. The arithmetic means of the plasma treated hybrids lap shear strength with polyamide 6.6 varied slightly but all measured values were within the range of the untreated samples. The lap shear strengths of the polypropylene hybrids were significantly reduced. This was attributed to an overaging and the development of low molecular weight oxidized materials which lead to a weak boundary layer. No correlation between surface free energy and the lap shear strength could be found.

Obesity and overweight are associated with many metabolic diseases, such as hypertension, diabetes, and dyslipidemia, which are closely related to a sedentary lifestyle and lack of exercise. Aerobic exercise effectively increases the high-density lipoproteins-cholesterol (HDL-C) levels and decreases the triglyceride (TG) levels. The consumption of Cuban policosanol (Raydel®) is also effective in enhancing the HDL-C quantity and HDL functionality to treat dyslipidemia and hypertension. On the other hand, no study has examined the effects of a combination of high-intensity exercise and policosanol consumption in obese subjects to improve metabolic disorders. In the current study, 17 obese subjects (average BMI 30.0±1.1 kg/m2, eight male and nine female) were recruited to participate in a program combining exercise and policosanol (20 mg) consumption for 12 weeks. After completion, their BMI, waist circumference, total fat mass, systolic blood pressure (SBP), and diastolic blood pressure (DBP) decreased by approximately 15% (p=0.022), 12.7% (p=0.008), 33% (p=0.006), 11% (p<0.046), and 13% (p=0.007), respectively. In the serum lipid profile, at week 12, they showed a remarkable decrease in the total cholesterol (TC) and triglyceride (TG) levels, up to 17% (p<0.019) and 54% (p<0.002) from the baseline, respectively. Although the serum HDL-C was increased by approximately +12% from the baseline, the percentage of HDL-C in TC, HDL-C/TC (%), was increased by up to +32% (p=0.007) at week 12. The serum coenzyme Q10 (CoQ10) level was increased 1.2-fold in all participants at week 12 from the baseline. In particular, the male participants showed a 1.4-fold increase (p=0.027) from the baseline. The larger increase in serum CoQ10 was correlated with the larger increase in the serum HDL-C during 12 weeks. The hepatic function parameters were improved; the serum -glutamyl transferase decreased at week 12 by up to 55% (p<0.007), while the aspartate aminotransferase and alanine transaminase levels decreased within the normal range. In the lipoprotein level, the extent of oxidation and glycation were reduced significantly in VLDL and LDL, with a remarkable decrease in the TG content in particles. The antioxidant abilities of HDL2 and HDL3, such as paraoxonase (PON) and ferric ion reduction ability (FRA), were enhanced significantly by up to 1.8-fold (p<0.001) and 1.6-fold (p<0.001) at week 12. The particle size and number of HDL2 were increased up to +10% during the 12 weeks with a remarkable decrease in the TG content, glycation extent, oxidation up to 32% (p=0.032), 18% (p=0.043), and 11% (p=0.023), respectively. The particle number and diameter of HDL3 were increased by up to +9% with a remarkable increase in the PON activity, FRA activity, and TC content of +82% (p<0.001), +56% (p<0.001), and +32% (p=0.009), respectively. Expression of apolipoproteinA-I in HDL2 and HDL3 were significantly elevated more in both gender around 30~48% with more distinct band intensity and less glycation at week 12. These improvements in HDL quality and functionality were linked to the higher survivability of adult zebrafish and their embryos. Under the co-presence of carboxymethyllysine (CML), a microinjection of HDL2 to zebrafish embryo from week 0 resulted in approximately 47% survivability with developmental defects and attenuated speed. On the other hand, the HDL2 microinjection from week 12 resulted in remarkably higher survivability (~ 70%). In conclusion, 12 weeks of Cuban policosanol (Raydel®, 20 mg) consumption with high-intensity exercise showed significant improvement in blood pressure, body fat mass, blood lipid profile without liver damage, CoQ10 metabolism, and renal impairment. At week 12, all participants showed a remarkable decrease in oxidation and glycation extent in the VLDL and LDL with a decrease in the TC and TG content. Significant enhancement of the qualities and functionalities in HDL2 and HDL3 by the policosanol consumption were also detected: increase in apoA-I content, TC content, particle size, and particle numbers along with antioxidant abilities, such as PON and FRA.

Aim: The purpose of this study is to evaluate the remineralization potential of primary teeth enamel after being exposed to different laser diode therapy. Methods: Ninety-six vestibular primary teeth enamel samples were divided into eight groups (n=12) with varying treatments: control (G1), CPP-ACP-fluoride varnish (G2), diode lasers at 980 nm (G3), 808 nm (G4), 450 nm (G5), 980 nm + CPP-ACP-fluoride varnish (G6), 808 nm + CPP-ACP-fluoride varnish (G7), and 450 nm + CPP-ACP-fluoride varnish (G8). Each sample was assessed using DIAGNOdent® at baseline, post-treatment, and post-pH cycle re-mineralization. SEM imaging was performed before and after treatment and following the pH cycle. Results: The results indicated that the 980 nm and 808 nm diode lasers, both alone and in combination with CPP-ACP-fluoride varnish, either maintained or increased the calcium (Ca) weight percentage (Wt%) in the enamel. The 980 nm diode laser combined with CPP-ACP-fluoride varnish (G6) showed a significant increase in Ca Wt%, suggesting a strong remineralization effect. Similarly, the 808 nm diode laser alone (G4) also promoted a substantial increase in Ca Wt%. In contrast, the 450 nm diode laser, whether applied alone or in combination with CPP-ACP-fluoride varnish, resulted in a lower Ca Wt% and an increase in phosphorus (P) Wt%. Most groups, except for the CPP-ACP-fluoride varnish alone (G2), demonstrated an increase in P Wt%, indicating a complex interaction between laser therapy and enamel remineralization. Conclusions: The combined use of laser therapy with CPP-ACP-fluoride varnish significantly enhanced the remineralization of temporary teeth enamel. The 980 nm diode laser + CPP-ACP-fluoride varnish showed the most pronounced improvement in remineralization, while the 808 nm diode laser alone also effectively increased calcium solubility. These findings suggest that higher wavelength diode lasers, particularly when combined with remineralizing agents, can effectively enhance the mineral content of primary teeth and promote enamel remineralization.

The German government's ambitious goal of achieving CO2-neutrality by 2045 has prompted a focus on improving building insulation as a vital step toward energy efficiency. However, in this process, existing radiators and boilers are often left unchanged, leading to inefficiencies due to oversized heating systems. This paper presents various approaches to reduce the required radiator inlet temperature, drawing on data from 100 multifamily buildings. The approaches include heat reserve reduction, heat power shifting, uniform radiator usage, and heat requirement analysis. These approaches collectively aim to lower flow temperatures and decrease peak heat loads, reducing energy consumption, and minimizing waste in compliance with the user comfort temperature. The findings reveal that the application of these methods can lead to substantial temperature reductions, with an average decrease of 20.82 K and 7.28 K for the highest necessary flow temperature in the provided example. Furthermore, peak load reductions of 21.07% and 13.65% were achieved, demonstrating the potential to enhance energy efficiency. While each approach can be applied individually, their synergistic implementation can highly increase the efficiency of water to x heat pumps, due to the lower required flow temperatures.

Climate change is increasing air temperatures and altering the precipitation and hydrological re-gime on a global scale. Challenges arise when assessing the impacts of climate change on the local scale for water resources management proposes, especially for low mountain headwater catch-ments that not only serve as important water towers for local communities, but also have distinct hydrological characteristics. Until now, no low flow or hydrological drought studies have been carried out on the Lauter River. This study is unique in that it compares the Lauter River, a transboundary Rhine tributary with a nearby station on the River Rhine just below its confluence at the French-German border. The Lauter catchment is a mostly natural, forested catchment, however, its water course has been influenced by past and present cultural activities. Climate change disturbances cascade through the hydrologic regime right down to the local scale. As we are expecting more low flow events, the decrease in water availability could cause conflicts be-tween different water user groups in the Lauter catchment. However, the choice of different methods for identifying low flow periods may cause confusion for local water resources manag-ers. Using flow rate time series of the Lauter River between 1956 and 2022 we compare for the first time three low flow identification methods: the variable threshold method (VT), the fixed threshold method (FT), and the Standardized Streamflow Index (SSI). Similar analyses are applied and compared to the adjacent Maxau station on the Rhine River for the same time period. This study aims at 1) interpreting the differences amongst the various low flow identification methods and 2) revealing the differences in low flow characteristics of the Lauter catchment compared to the Rhine River. It appears that the FT reacts faster to direct climate or anthropogenic impacts whereas VT is more sensitive to indirect factors such as decreasing subsurface flow which is typical for small headwater catchments, such as the Lauter where flow dynamics react faster to flow disturbances. Abnormally low flow during the early Spring in tributaries such as the Lauter can help predict low flow conditions of the Rhine River during the following half year and espe-cially for the summer. The results could facilitate Early Warning of hydrological droughts and drought management for water users in the Lauter catchment and further downstream along some of the Rhine.

As the PCIe 6.0 specification places higher requirements on signal integrity and transmission la-tency, it becomes especially important to improve signal transmission performance at the physical layer of the transceiver interface. Retimer circuit as a key component of high-speed serial interface, its delay and jitter size directly affect the overall performance of PCIe. For the conventional Retimer circuit with large latency and low jitter performance, this paper proposes a low latency and low jitter Retimer circuit based on CDR+PLL architecture for PCIe 6.0, using a jitter canceling filter circuit to eliminate the frequency difference between the retiming clock and data, reduce the retiming clock jitter, and improve the quality of Retimer output data; The data is sampled using the retiming clock and then output, avoiding the problem of large penetration latency of con-ventional Retimer circuits. The circuit is designed using CMOS 28nm process. Simulation results show that when 112Gbps PAM4 data is input to the Retimer circuit, the Retimer penetration la-tency is 27.3 ps, which is 83.5% lower than the conventional Retimer structure; the output data jitter is 741 fs, a 31.4% reduction compared to the conventional Retimer structure.

African scientific research faces formidable challenges, particularly with limited access to state-of-the-art measurement instruments. The high cost associated with these devices presents a significant barrier for regional research laboratories, impeding their ability to conduct sophisticated experiments and gather precise data. This predicament not only hampers the individual laboratories but also has broader implications for the African scientific community and the advancement of knowledge in developing nations—the financial cost barrier considerably impacts the research quality of these laboratories. Reflection on technical and economical solutions needs to be quickly found to help these countries advance their research. In civil Engineering, the thermal conductivity property is the most important measurement for characterising heat transfer in construction materials. Existing devices (i.e., conductometers) in a laboratory are expensive (approximately 30,000 euros) and unavailable for some African laboratories. The study proposes a new and affordable device to evaluate thermal conductivity in construction materials. The method involves establishing a thermal flux between a heat source ( from the Joule effect provided by steel wool where a current is circulating) and a cold source (generated by ice cube) under steady-state conditions. The development of the cylindrical prototype is based on the comparative flux-meter method outlined in the measuring protocol of the ASTM E1225 standard document. Experiments were conducted on four distinct materials (polystyrene, wood, agglomerated wood, and rigid foam). The results indicate a correct correlation between the experimental values obtained from the newly developed prototype and the reference values found in the literature. For example, concerning the experimental polystyrene study, the detailed case analysis reveals a good correlation, with a deviation of only 4%. The percent error found falls within the acceptable range indicated by the standards recommendations of the ASTM E1225 standard, i.e., within 5% acceptable error.

A novel low-power MOS-only voltage reference is presented. The Enz-Krummenacher-Vittoz (EKV) model is adopted to provide a new perspective on the operating principle. The normalized charge density, introduced as a new variable, serves as an indicator when trimming the output temperature coefficient. The proposed voltage reference consists of a specific current generator and a 5-bit trimmable load. Thanks to the well-match between the current source stage and the output stage, the non-linear temperature dependence of carrier mobility is automatically canceled out. The circuit is designed in 55 nm COMS technology. The operating temperature ranges from -40 ∘C to 120 ∘C. The average temperature coefficient of the output voltage can be reduced to 21.7 ppm/∘C by trimming. The power consumption is only 23.2 nW with a supply voltage of 0.8 V. The line sensitivity and the power supply rejection ratio at 100 Hz are 0.011 %/V and -89 dB respectively.

Low volatility ETFs have become popular in recent year because investors are starting to understand the advantages involved in investing in those ETFs compared to traditional index investment. In this research I have examined the performance of six popular low volatility ETFs, four of them invest in U.S stocks and the other two invest in other developed and emerging markets. Results have pointed out that not only five of the low volatility ETFs have exposed their investors to lower risk, four of them have also produced higher returns. The advantage of investing in low volatility ETFs is prominent in the U.S stock market. All three sizes of stocks categories (Large, Mid and Small Capitalization) low volatility ETFs have outperformed their indexes bench marks in terms of risk and returns. For the non U.S stock investing, while no advantage have been found for investing in low volatility ETFs for developed countries, significant lower risk was found for emerging markets.

Low dropout (LDO) regulators are widely used in portable electronic devices because they 1 occupy small chip and printed circuit board (PCB) areas. This work presents the design of a low 2 noise low dropout (LDO) linear voltage regulator using folded cascode operational amplifier and 3 source follower buffer for frequency compensation. The proposed design achieves low output noise 4 with feedback loops, which makes it possible to improve load and line regulations as well as the 5 transient response for voltage applications in comparison with the literature. The designed LDO 6 linear regulator works under the input voltage of 2.8-4.8 V and provides up to 100 mA load current 7 for an output voltage of 2.6 V. 8 9 Moreover, the operational amplifier design contributes to the major reduction in the frequency 10 noise, and make sure the stability of LDO under different conditions. Furthermore, the novel LDO 11 design topology has very less dropout voltage, fast transient response and minimized power dissi- 12 pation under maximum load current, worst process corner, and maximum temperature to achieve 13 high power efficiency, maintain output voltage in the presence of fast load changes, and to lower the 14 power loss across the pass element especially at high load. Design criteria are addressed in detail. 15 16 This LDO topology is able to achieve ultra-low noise i.e. 2 /muv/√Hz for frequency >1kHz. The 17 proposed LDO is implemented in the cadence virtuoso H9A with CMOS 130 μm technology.

Logistics industry has been found to be among the key sources of carbon emission. In Vietnam logistics industry, there is a considerable difference between the number of foreign and Vietnamese firms as well as the proportion of markets that they are taking. This study is to research the low-carbon emission measures conducted by domestic and foreign invested logistics service providers (LSPs) and compare the results of the two groups. Both qualitative and quantitative approaches are applied. Literatures in relevant fields are reviewed and expert opinions are taken for structuring a questionnaire which was later distributed to 279 LSPs, with 166 returned and 159 being valid for data calculation. The results imply that there are differences in extension of applications of low-carbon practices between foreign and domestic firms. Except for transport mode switch and energy-saving lighting, the other practices witness that adoption levels of foreign LSPs are higher than their counterparts, which is possibly thanks to their global operation, more comfortable capital resources and awareness level of green initiative necessity. In conclusion, a comparison between the application conducted by foreign-invested firms and domestic ones, which has not been investigated before, was made.

Digital-based differential amplifiers (DDA) are particularly suitable to low voltage digital integrated circuit technologies. This paper presents an exhaustive analysis of the digital-based analog amplifiers to take advantage of today's high-performance digital technologies and of computer-aided design (CAD) commonly employed to design integrated circuits. The operating principle and the main mathematical relations of the digital-based differential amplifiers are discussed along with an exhaustive explanation of its operating regions and of the corresponding power consumption. Finally, a detailed description of the design procedure of in UMC 180nm standard CMOS technology is shown.

HER2-low and ultra-low breast cancer (BC) have been recently proposed as new subcategories of HER2 BC, re-considering the immunohistochemical negative score of 0, 1+ or score of 2+/in situ hybridization (ISH) negative phenotype. In the present review we have outlined the needed criteria to exactly distinguish HER2 low and ultra-low BC. Recent clinical trials have demonstrated significant clinical benefits of novel HER2 directing antibody-drug conjugates (ADCs) in treating these group sof tumors. In particular, Trastuzumab-deruxtecan (T-Dxd), a HER2-directing ADC has been recently approved by the U.S. Food and Drug Administration as the first targeted therapy to treat HER2-low BC. Furthermore, ongoing trials, such as the DESTINY-Breast06, are currently evaluating ADCs in patients with HER2-ultra low BC. Finally we hope that new guidelines may help to codify HER2 low and ultra-low BC, increasing our knowledge of tumor biology and improving a targetable new therapeutical treatment.

Multidisciplinary Design Optimization (MDO) is the most active field in the design of current complex system engineering, which is possessed with such two difficulties as subsystem information exchange and analytical and computational complexity of systems. Therefore, an improved collaborative optimization algorithm based on ANN (artificial neural network) response surface was proposed dependent on the consistency constraint algorithm and concurrent subspace algorithm. As an optimization method with secondary structure, it satisfied only local constraints in discipline layer, but provided a coordinated mechanism for interdisciplinary conflict in system layer. Finally, it was applied in the multidisciplinary design optimization of autonomous underwater vehicle (AUV). As shown from the result, the MDO convergence stability and reliability of low resistance, low noise and high maneuvering performance of the AUV shape can be ensured by the improved collaborative optimization algorithm, thus verifying the effectiveness of the algorithm.

Many studies utilize sensors to measure foot plantar pressure and analyze gait patterns, often focusing on assessing weight-bearing symmetry or asymmetry compared to control groups. However, a critical question arises: does the selection of the control group significantly impact study outcomes? Does chronic low back pain affect foot plantar pressure measurements? This experimental study involved 23 participants, including healthy individuals and those without foot disorders but with chronic low back pain. Dynamic foot pressure measurements were conducted using the Ortopiezometr, and data were analyzed using the "Steps" program. Participants were divided into two groups: Group 1 comprised completely healthy individuals, while Group 2 consisted of individuals without foot problems but with moderate chronic low back pain. The findings highlight a prevalence of energy release in the forefoot sensors compared to the hindfoot for both the right and left legs in most cases. Even among healthy volunteers, achieving perfect symmetry in the maximum values on the sensors for the right and left feet was a challenge. Results showed no statistically significant differences in energy released on specific sensors or duration of gait phases between the groups. Essentially, this suggests that foot pressure patterns are comparable between healthy individuals and those with low back pain. The use of sensor-equipped inserts for pedobarographic examinations indicates that, in cases of degenerative changes in the lumbar and sacral spine without accompanying acute pain, gait patterns resemble those of the healthy population.

Background: Low birth weight (LBW) is a major public health problem in low-income countries. Infants born with LBW are at increased risk of neonatal mortality, have poorer school performance, and are more likely to develop respiratory and cardiovascular diseases in adulthood. Methods: An unmatched case–control study was conducted in five maternity wards in the Kenge Health Zone, involving 159 mother–newborn pairs. Data analysis was performed using STATA 18.0 software. Bivariate and multivariate analyses were used to determine the associations between independent variables and LBW. Results: Determinants of low birth weight were maternal short stature (height &lt; 155 cm) (adjusted odds ratio (AOR): 3.90; 95% confidence interval (CI): 1.66–9.13), maternal non-indigenous Yaka ethnic group (AOR: 2.39; 95% CI: 1.01–5.66), having attended fewer antenatal care (ANC) sessions (AOR: 0.73; 95% CI: 0.53–0.99), and inadequate maternal dietary diversity (AOR: 3.97; 95% CI: 1.25–12.62). Conclusions: Increased education and awareness of dietary diversity as an indicator of dietary quality in women of childbearing age, especially during pregnancy, along with regular follow-up of antenatal care visits and behavior change communication targeting pregnant women, can help health professionals address dietary taboos and reduce the incidence of LBW.

For underwater vehicles navigating in Arctic Sea ice-covered waters, fatigue damage is a crucial issue. Many scholars have conducted low-temperature fatigue analysis on low-temperature ma-terials and substrate platforms for ships, and the results show that low-temperature is beneficial for improving the mechanical properties of materials. However, they mainly focus on low-temperature performance experiments and simulation analysis of standard components of materials, and there are very few fatigue life experimental studies on underwater vehicle me-chanical structures. This paper conducts experimental investigations on a scaled model of an underwater vehicle rudder mechanism in a polar environment laboratory. Using a comparative analysis method involving simulations and experiments, the low-temperature fatigue test data of the scaled underwater vehicle rudder mechanism are analyzed, and the quantified analysis be-tween fatigue and different low-temperature loading cycles, as well as the influence of icing on the fatigue life, is explored. It is indicated that the arctic environment can decrease the fatigue life of the underwater vehicle rudder mechanism by deteriorating its material properties. The paper builds the foundation for the fatigue life of an underwater vehicle rudder mechanism in arctic low-temperature environments.

Poly(2,6-dimethyl phenyl oxide) (PPO) is known for its low dissipation factor. To achieve insulating materials with low dissipation factor for high-frequency communication application, a monomer-type benzoxazine (P-APPO) and a main-chain-type benzoxazine (BPA-APPO) were prepared from an amine end-capped oligo (2,6-dimethyl phenylene oxide) (APPO). The APPO was prepared from a nucleophilic substitution of a phenol-end capped oligo (2,6-dimethyl phenylene oxide) (a commercial product, SA 90) with fluoronitrobenzene, and followed by catalytic hydrogenation. After self-curing or curing with a dicyclopentadiene-phenol epoxy (HP 7200), thermosets with high-T_g and low-dissipation factor can be achieved. Furthermore, the resulting epoxy thermosets show better thermal and dielectric properties than those of epoxy thermoset cured from its precursor SA90, demonstrating it is a successful modification in simultaneously enhancing the thermal and dielectric properties.

To achieve rapid post-earthquake repair of self-centering ribbed floor flat beam frame structures, a ductile hybrid joint consisting of dog bone weakened energy dissipating steel bars connected to the upper and lower column sections through high-strength threads based on the damage control design concept is proposed. By moving the ductile energy dissipating zone out to the locally weakened section of the energy dissipating steel bars and the locally unbonded prestressed steel bars in the core area, the residual deformation was limited and the seismic performance was improved. Based on the working principle of hybrid joints, low cycle loading tests were conducted on two joint specimens to analyze the influence of lateral prestress on the seismic performance of the hybrid joints. Numerical modeling methods were used to compare the position of the energy-consuming steel bars in the composite layer and the friction performance of joints. The research results indicated that the hybrid joint had stable load-bearing, deformation, and energy dissipation capabilities, with damage primarily concentrated on the energy-consuming steel bars. Even at an inter-story displacement angle of 5.5%, the upper and lower column segments remained elastic. After unloading, the connection seam at the joint was closed, and the self-centering performance was good. When the inter-story displacement angle reached 5.5%, the lateral prestress increased from 150 kN to 250 kN, the ultimate bearing capacity of the joint increased by 16.3%, and the cumulative energy consumption increased by 30.0%. The influence of the friction coefficient of the joint surface on the structural performance was set at a threshold of 0.7. When it was less than the threshold, the ultimate bearing capacity and initial stiffness of the joint increased with an increase in the friction coefficient. After reaching the threshold, the increase in the ultimate bearing capacity of the joint slowed down, and the rate of stiffness degradation gradually accelerated. This joint had excellent seismic performance and can also achieve post-earthquake repair of structures.

The influence of the Fe2O3 addition amount on the dephosphorization of hot metal at 1623 K with the slag of the low basicity (CaO/SiO2) of about 1.5 was investigated by using high-temperature laboratorial experiments. With increasing the Fe2O3 addition amount, the contents of [C], [Si], [Mn] and [P] in hot metal at the end of dephosphorization decrease, and the corresponding removal ratios increase. The P2O5 content in slag increases, and the CaO and SiO2 contents in slag decrease. The phosphorus mainly exists in the form of the nCa2SiO4-Ca3(PO4)2 solid solution in the phosphorus-rich phase and the value of coefficient n decreases from 20 to 1 with increasing the Fe2O3 addition amount from 5 g to 30 g. With increasing the Fe2O3 addition amount, the oxygen potential and activity at the interface between the slag and hot metal increase. When the oxygen potential and the oxygen activity at the interface are greater than 0.72×10-12 and 7.1×10-3, respectively, the dephosphorization ratio begins to increase rapidly. With increasing the Fe2O3 addition amount to 30 g, the ratio of the Fe2O3 addition amount to theoretical calculation consumption is around 175%, and the dephosphorization ratio reaches the highest value of 83.3%.

Low 25 OH vitamin D (25(OH)D) in preterm infants is a risk factor of bronchopulmonary dysplasia (BPD), but increased supplementation failed to demonstrate beneficial effect on BPD. In neonatal animal models, deficiency and excessive vitamin D exposure have been associated with increased mortality and lung histological alterations evocative of BPD. Our hypothesis is that 25(OH)D levels ≥ 120nmol/L is also a risk factor for BPD or death. This retrospective single-center cohort study included all infants born <31 weeks gestational age without major malformation with at least a determination of 25(OH)D <36 weeks corrected age and no determination <50 nmol/L. Routine 25(OH)D determination was performed at 1 month and monthly thereafter. A total of 175 infants were included. Infants with BPD or who died had a significantly lower term and weight, but a similar frequency of 25(OH)D ≥120nmol/L (50.5% vs 43.9%, p=0.53). The logistic regression identified weight (OR 0.997, 95%CI [0.995-0.998]) and term (OR 0.737, 95%CI [0.551-0.975]) as significantly associated with BPD or death; the occurrence of excessive 25(OH)D was not significantly associated (OR 1.029, 95%CI [0.503-2.093]). The present study did not demonstrate any significant association between excessive 25(OH)D after one month of age and BPD or death.

An accurate flux measurement of low-energy charged particles trapped in the magnetosphere is necessary for space weather characterization and to study the coupling between the lithosphere and magnetosphere, which allows for the investigation of the correlations between seismic events and particle precipitation from Van Allen belts. In this work, the project of a CubeSat space spectrometer, the Low-Energy Module (LEM), is shown. The detector will be able to perform an event-based measurement of the energy, arrival direction, and composition of low-energy charged particles down to 0.1 MeV. Moreover, thanks to a CdZnTe mini-calorimeter, the LEM spectrometer also allows for photon detection in the sub-MeV range, joining the quest for the investigation of the nature of Gamma-ray bursts. The particle identification of the LEM relies on the ΔE−E technique performed by thin silicon detectors. This multipurpose spectrometer will fit within a 10 × 10 × 10 cm3 CubeSat frame, and it will be constructed as a joint project between the University of Trento, FBK, and INFN-TIFPA. To fulfil the size and mass requirements, an innovative approach, based on active particle collimation, was designed for the LEM; this avoids the heavy/bulky passive collimators of previous space detectors. In this paper, we will present the LEM geometry, its detection concept, the results from the developed GEANT4 simulation, and some characterisations of a candidate silicon detector for the instrument payload.

Tropical rock lobsters (Panulirus ornatus) are a highly cannibalistic species with intermoult animals predominantly attacking animals during ecdysis (moulting). Rapid, positive characterisation of pre-ecdysis lobsters may open a pathway to disrupt cannibalism. Ecdysial suture line development is considered for pre-ecdysis recognition with suture line definition compared for lobsters emerged and immerged, using white, near ultraviolet (365 nm), near infrared (850 nm) and spe-cialty Osram SFH 4737 broadband IR LEDs against a reference of intermoult lobsters with no suture line development. An alternative pre-ecdysis recognition strategy used a novel low-cost spectral camera composed of the Sony IMX219, AMS AS7265x spectral sensors and Osram SFH 4737 broadband infrared LEDs. Images and data using the novel low-cost spectral camera was acquired from intermoult, pre-ecdysis, and post-ecdysis lobsters. Compared with the white light appear-ance, suture line definition was enhanced under 850 nm, 365 nm, and SFH 4737 LEDs for immerged lobsters, while the 850 nm LED achieved the best suture line definition of emerged lobsters. The spectral camera was unable to characterise pre-ecdysis. A least squares regression for binary classification decision boundary successfully separated 86.7% of post-moult lobsters. Achieving post-moult characterisation validated the speculative exploratory approach in developing this novel low-cost spectroscopy tool.

GNSS is nowadays a standard tool for monitoring and studying the Earth’s dynamic environment. However, the development of dense GNSS measurements remains limited in many experiments by the cost of geodetic-class equipments allowing to achieve the high precision required by many applications. Recently, multi-constellation, multi-frequency, low-power and, above all, less expensive GNSS electronic chips have become available. We present a prototype of a low-cost, open-source multi-GNSS station. Our prototype comprises a dual-frequency GNSS chip, a calibrated antenna, a Raspberry Pi card and a 4G key for data transmission. The system is easy to deploy in the field and allows precise positioning in real time and post-processing. We assess the performance of our prototype in terms of raw data quality, and quality of the obtained high rate and daily position one-year-long time series. Our results demonstrate a quality equivalent to geodetic-class equipment and better quality than other low-cost systems proposed so far.

The manufacturing geometrical variability in axial compressors is a stochastic source of uncertainty, implying that the real geometry differs from the nominal design. This causes the real geometry to lose the ideal axial symmetry. Considering the aerofoils of a stator vane, the geometrical variability affects the flow traversing it. This impacts the downstream rotor, especially when considering the aeroelastic excitation forces. Optical surface scans coupled with a parametrization method allow for acquiring the information relative to the real aerofoils geometries. The measured data are included in a multi-passage and multi-stage CFD setup to represent the mistuned flow. In particular, low excitation harmonics on the rotor vane are introduced due to the geometrical deviations of the upstream stator. The introduced low engine orders as well as their amplitude depend on the stator geometries and their order. A method is proposed to represent the phenomena in a reduced CFD domain, limiting the size and number of solutions required to probabilistically describe the rotor excitation forces. The resulting rotor excitation forces are reconstructed as a superposition of disturbances due to individual stator aerofoils geometries. This indicates that the problem is linear in in the combination of disturbances from single passages.

Disseminated or military tuberculosis (TB) is defined as the presence of at least two non-contiguous sites of Mycobacterium tuberculosis, occurring as a result of progressive primary infection, reactivation and spread of a latent focus or due to iatrogenic origin. Disseminated TB represents a life-threatening condition, especially in at-risk children and when the diagnosis and treatment are delayed. We report on a case of a 3-year old boy who presented with long-lasting unrecognised disseminated TB that was successfully managed in a low-resource setting.

This paper presents high-resolution digital measurements at low cost, combining oversample and averaging. Experiments of processing data between samples and between multiple temperature sensors in the same environment are conducted. They provide results with effective increase in the analog to digital converter bits, in correspondence with the minimization on the effects of noise. It is shown that averaging a set of small, low-cost sensors at a small microcontroller can give flexible access to improved measurement accuracy.

The production and secretion of very-low density lipoproteins (VLDL) by hepatocytes has a direct impact on liver fat content as well as the concentration of cholesterol and triglycerides in the circulation and thus affects liver and cardiovascular health, respectively. Importantly, excess caloric intake and lack of physical activity are associated with overproduction of VLDL, hepatic steatosis, and increased levels of atherogenic lipoproteins. Cholesterol as well as triglycerides in remnant particles after VLDL lipolysis are risk factors for atherosclerotic cardiovascular disease (ASCVD) and have garnered increasing attention over the last few decades. To date, however, increased risk of ASCVD is not the only concern when considering today’s cardiometabolic patients, as they often also suffer from hepatic steatosis. This notion highlights the importance of understanding the molecular regulation of VLDL biogenesis. Fortunately, there has been a resurgence of interest in the intracellular assembly, trafficking, degradation, and secretion of VLDL by hepatocytes, that has led to many exciting new molecular insights, the topic of this review. We think that increasing our understanding of the biology of this pathway will help improve the health of the cardiometabolic patient in the long term.

Two modal decomposition techniques, including proper orthogonal decomposition (POD) and dynamic mode decomposition (DMD), are used to identify the wake patterns past single and two crossing cylinders in 60° and 90° arrangements with gap ratio G = 4. The flow is simulated using direct numerical simulations (DNS) for Reynolds numbers Re = 100. The spatial scale of flow decreases with increasing modal frequency from the modal analysis. Two main modes are identified in the wake of the cylinders, namely spatially antisymmetric and symmetric modes. Antisymmetric and symmetric modes are related to cylinders’ vortex shedding and shedding vortices’ shift motion, respectively, whose frequencies are odd and even multiples of cylinders’ lift force frequency. In addition, a low-frequency mode concerning the shadowing effect of the downstream cylinder (DC) in 90° arrangement is found in the wake of the DC centre.

The present work aimed to validate a low-cost passive monitoring procedure. For its validation, the monitoring of atmospheric organic pollutants - polycyclic aromatic hydrocarbons (PAH) was carried out in a capital of the central-western region of Brazil. The sensors were fixed on poles intended for electrification during the dry season. After 15 days, samples were extracted by solvent extraction and analysed by High-Resolution Gas Chromatography with Flame Ionization Detector (HRGC-FID). For the validation of the procedure, PAHs monitored and standardised by the American Environmental Agency (EPA), a benchmark for environmental monitoring of air quality by several countries, were analysed. The results demonstrated that the low-cost passive monitoring method was effective in the quantification of PAH in the environment-air, capable of being used by countries that do not have many resources for monitoring air quality.

This article introduces the design and analysis of a slope detection circuit tailored for on-chip sensing of the load current in DC-DC converters. The novel indirect sensing approach is grounded in measuring the output voltage slope across the filtering capacitor during discharge phases. Consequently, this slope data can be effectively harnessed to control the converter switches. The slope detector circuit was designed in standard 65 nm CMOS technology using the nominal supply voltage of 1.2 V and can be used for current sensing within the range from one to hundreds of mA. Since the proposed circuit has mainly digital character, the robustness to process, temperature and supply voltage variations can be ensured rather conveniently.

Background: Protein CCDC186 is involved in the maturation of dense core vesicles in the trans-Golgi network in neurons and endocrine cells. To date, only one patient, within a large sequencing study of 1000 cases, and a single case report with variants in CCDC186 had previously been described. However, no functional studies in any of these two cases had been performed. Methods: Exome sequencing from one affected individual of each family was performed. In addition, Sanger sequencing of the parents and one of the affected siblings was also performed. CCDC186 protein was assessed in cultured fibroblasts or muscle tissue by western blot. Transcriptomic analysis was done by means of RNA sequencing. Results. We identified three patients from two gypsy families, unrelated to each other, with the same homozygous mutations in CCDC186 gene. Clinically, all patients presented with seizures, frontotemporal atrophy, hypomyelination, recurrent infections, and endocrine disturbances such as severe non ketotic hypoglycemia. Low levels of cortisol, insulin or growth hormone could only be verified in one patient. All of them had a neonatal onset and died between 7 months and 4 years of age. WES identified a homozygous variant in CCDC186 gene (c.2215C>T, p.Arg739Ter) in the index patients of both families. Protein expression studies demonstrated that the CCDC186 was practically undetectable in fibroblasts and muscle tissue. These observations correlated perfectly with the transcriptomic analysis performed in fibroblasts in one of the patients, which showed a significant reduction of CCDC186 mRNA levels. Conclusion. Our study provides functional evidence that mutations in this gene have a pathogenic effect on the protein and reinforces CCDC186 as a new disease-associated gene. In addition, mutations in CCDC186 could explain the combined endocrine and neurologic alterations detected in our patients

This paper aims at trying to answer the question of whether a low cost drone equipped with a regular camera can serve as a simple device to estimate the size of objects. Ad-ditionally, it assesses if the accuracy of measurement is good enough for using a drone for measurements, relying solely on GPS position and camera. A review of the literature pertaining to ground object measurements was conducted. The availability of such in-struments was evaluated in terms of purchase and rental costs, the number of instru-ments on the market, and the time to obtain them. The most common measurement methods were considered and their unit costs were reviewed. The cost of professional surveying and measuring equipment was compared to the possibility of using low-cost, non-commercial drones to measure objects and surfaces. The quality of the images ob-tained was compared with high-resolution satellite systems. Is an ordinary drone with a standard camera suitable for length measurement without professional measuring equipment? Should the results be considered only in the category of size estimation?

One of the key issues in sustainable tourism research is the gap between tourists' expressed friendly attitudes towards sustainable behaviors and their actual behaviors. Although many "low-carbon" themed restaurants have emerged during the low-carbon transformation of the Chinese tourism industry, low-carbon food services have not been significantly improved. This study takes food as the entry point to explore tourists' behavior and attitudes towards low-carbon tourism in relation to food. We conducted two interviews. The first interview was a semi-structured contextual interview with 120 tourists who had experiences in food streets, aim-ing to identify the core user group: low-carbon attitude-friendly tourists with high-carbon food behaviors. The second interviews was an in-depth interview based on grounded theory with 29 core users, analyzing the four main reasons for their high-carbon food behaviors and their re-quirements for low-carbon food services in tourism. Based on this, we extracted four design ele-ments for low-carbon tourism food services: low-carbon information show service, low-carbon service product attractiveness improvement, low-carbon food environment atmosphere creation, and service providers' low-carbon behaviors. Through these four service elements, we constructed a low-carbon tourism food service design framework based on the core users' needs, discussed the mechanism of service elements, and provided service design suggestions accordingly. The re-search results serve tourism providers, low-carbon tourism researchers, and designers.

Chronic pain is a serious health concern and potentially debilitating condition, leading to anxiety, depression, reduced productivity and functionality, and poor quality of life. This condition can be even more detrimental and incapacitating in the pediatric patient population. In low and middle income countries (LMICs), pain services are inadequate or unavailable, leaving most of the world's pediatric population with chronic pain untreated. Many of these children in LMICs are suffering without treatment, and often die in pain. Awareness and advocacy for this population must be prioritized. We reviewed the available literature on the chronic pediatric pain burden in LMICs, barriers to treatments, and current efforts to treat these patients.

Hamstring muscle (HM) flexibility is frequently compromised in people with chronic low back pain (CLBP), contributing to disability and leading to a less favorable recovery. In a previous article, we presented the results of a study on the immediate effect of passive HM stretching on flexibility in 90 people with CLBP. There was considerable variability in the changes after stretching. The objective of this supplementary analysis was to compare the clinical characteristics of individuals who experienced a significant improvement in flexibility with those who did not. We fixed a threshold of 7° to indicate an improvement in passive Straight Leg Raise (SLR) angle and differentiate between 'Responders' and 'Non-responders' to passive HM stretching. Only Body Mass Index differed between groups; it was significantly smaller in Responders (p=0.007). The majority of Non-responders experienced workplace accidents, but this was of marginal difference compared to Responders (p=0.056). Further studies should consider a broader clinical analysis with a larger sample size to understand which factors influence the HM stretching response in CLBP patients.

Iron supplementation is associated with side effects and thus reduces the intake compliance. Because it has fewer side effects, a recent trial recommended low-iron micronutrient powder (MNP) for the prevention of anemia in Bangladeshi children exposed to a high concentration of iron from drinking groundwater. In the present study, we hypothesize that the low-iron MNP is a potential intervention to prevent childhood anemia in the low groundwater-iron settings in Bangladesh. A cross-sectional study was conducted in Bangladesh with children aged 2-5 years who drank groundwater containing a low level of iron (0-&lt;2 mg/L).The combined intake of iron was calculated from the key sources--diet, groundwater and MNPs. The intakes of iron were compared against the standard reference intake. The children’s hemoglobin was measured using a photometer. Combined intake of iron from dietary, groundwater and low-iron MNP in children was 5.8±2.0 and 6.9±2.5 mg/day comprising 193% and 169% of the Estimated Average Requirement in the 2-3 year-old and 4-5 year-old subgroups, respectively. Combined intake of bioavailable iron from dietary and groundwater sources was 0.42±0.023 and 0.22±0.019 mg/day in children exposed to groundwater concentration 0.8-&lt;2.0 mg/L and 0.0-&lt;0.8 mg/L respectively (p&lt;0.001). The mean concentration of hemoglobin in the respective groups was 12.17±0.94 mg/dl and 11.91±0.91 mg/dl (p=0.30). The combined intake of iron from dietary and groundwater sources was associated with maintenance of hemoglobin concentration at the non-anemic level in most of the children. The finding highlights the potential of low-iron MNP in controlling childhood anemia in this setting.

Uncertainties in initial water saturation and early water breakthroughs of un-known sources and paths, which occurred in the low resistivity Lower Haushi sand-stone (LHS) reservoir at the beginning of oil production, imply that the bypassed oil can yet remain in the reservoir. In addition, the upper part of LHS is a tight oil reser-voir, which can still contain a significant amount of unrecovered oil. This opens the opportunity to produce the remaining oil instead of abandoning this reservoir. Low resistivity can exaggerate water saturation, leading to misinterpretation and premature water flooding due to inadequate oil-water contrast. Our analysis revealed a correlation between low resistivity and robust porous network connectivity, along-side elevated formation water salinity in highly porous layers. In regions of high po-rosity, sufficient oil-water contrast facilitates precise water saturation determination, affirming oil presence in all wells. However, within tight oil zones, near-complete wa-ter saturation contradicts actual oil presence. Factors contributing to saturation un-certainty and water breakthroughs were reassessed. Utilizing a 1:1 verti-cal-to-horizontal permeability ratio derived from core data enhanced simulation alignment with water production rates. Investigation into the impact of relative per-meabilities on water production was conducted. Water saturation maps were gener-ated to pinpoint remaining oil reserves. Depletion around wells is evident in lower po-rous regions, while oil persists across the entire tight reservoir, notably in two unex-plored sections.

To investigate the structural behavior of simply supported concrete beams with steel and polypropylene fiber under low velocity impact loading. In all twenty-four beams (150X200X1800 mm) with simply supported boundary condition were modeled and analyzed using ABAQUS software. Steel and polypropylene fibers of aspect ratio of 60 and 231 respectively are used. The total volumes of fibers are maintained at 1% by volume of specimen. A 100 kg hammer with tip diameter 16 mm (hemispherical contact area = 201 mm2) with four different velocities (3.13 m/s, 4.42 m/s, 5.43 m/s and 6.11 m/s) were used in the analysis. It is observed that with the addition of hybrid fibers the deflection in beams was reduced. The beams with 1% PP and 0% steel fiber shows the maximum deflection values due to low modulus of elasticity. Beams with 0.9% steel and 0.1% polypropylene fibers was less affected in terms of deflection as compared to all other beams, it is due to presence of high tensile strength fibers.

Phenylketonuria is an inherited metabolic disorder that leads to neurobehavioral dysfunction. The main treatment is a low-phenylalanine diet and/or the cofactor tetrahydrobiopterin. Regular outpatient follow-up care and measurement of the phenylalanine level in the blood are required. We aimed to analyze the economic burden of phenylketonuria on families and the state. The pa-tients with phenylketonuria were divided into three groups according to their treatment: a low-phenylalanine diet group (n= 50), a tetrahydrobiopterin group (n= 44) and a group taking tetra-hydrobiopterin together with the diet (n= 25). A comparative cost analysis was carried out. The annual economic burden to the state was calculated to average €18801±15345 and was lowest in the diet group, then in the tetrahydrobiopterin group and highest in the tetrahydrobiopterin+diet group (p < 0.001). Out-of-pocket costs amounted to €1531±1173 per year, and indirect losses aver-aged €2125±1930 per year for all families. The economic loss was significantly lower in the fami-lies taking tetrahydrobiopterin than in the other groups (p=0.001). The combined use of medical nutrition and BH4 treatments has been shown to increase the economic harm to the state. Reim-bursing low-protein products and increasing the rate of patients eligible for financial allowances may reduce the economic harm to families.

In the field of delta-sigma modulators, reducing system power consumption without sacrificing accuracy has become a challenge. The summing circuit, as the main part of the cascade-of-integrator-in-feedforward delta-sigma modulator, consumes a significant amount of power in active summing. On the other hand, passive summing circuits have low power consumption but can cause attenuation in the summing results. This article proposes a low-power multi-bit delta-sigma modulator based on passive and attenuationless summation scheme. The summation circuit achieves multiplication of the voltage signal carried on the summation capacitor through bidirectional sampling technique, compensating for the inherent attenuation caused by passive summation, thus eliminating the need for active OTA to achieve perfect summation. A 2-order delta-sigma modulator based on 4-bit 1-order passive noise-shaping (NS) SAR quantizer is designed to verify the scheme. By combining a passive NS SAR as the 4-bit quantizer and the third-stage integrator of the system, and incorporating an energy-efficient cascode floating inverter amplifier (FIA) structure as the core active OTA, these elements have significantly enhanced the energy-efficiency of the modulator. Simulation results show that at a supply voltage of 1.2 V and a bandwidth of 20 kHz, the SNDR reaches 102.62 dB, power consumption is only 148.32 μW, and Schreier figure-of-merit (FoM) of SNDR is 183.92 dB.

The low-altitude quasi-periodic (LQP) E-region echoes observed with the upgraded HCOPAR located in Hainan Island of China (19.5°N, 109.1°E) are presented. With the interferometry technique, the interferometry equations can be developed to investigate the structures of the irregularities. The results show that the plasma structures of the LQP echoes with negative slope mainly drift southwestward almost horizontally, but they also drifted southeastward in some striations. According to the movement of the plasma structures, we find strong wind shear in the region where the LQP echoes are produced. Meanwhile, The periodicity of the LQP echoes may be related to the strength of the wind shear. It is proposed that the plasma structures are most likely produced by the Kelvin-Helmholtz instability.

Glucose is an important carbon sources for microbial growth, and its content in infertile soils is essential for the growth of the bacterium. Since the mechanism of oligotrophic bacterium adaptation in barren soils is unclear, the research employed RNA Seq technology to examine the impact of glucose concentration on the low nutrient bacteria BS-G1 in soil affected by desertification. RNA-Seq revealed that differentially expressed genes（DEG）histidine metabolism, glutamate synthesis, HIF-1 signalling pathway, sporulation, and TCA cycle pathway of BS-G1 were significantly enriched in 0.015 g/L glucose concentration, compared with 10 g/L glucose concentration. DEG amino acids system, two-component system, Metal Ion Transport, and nitrogen metabolism system of B. subtilis BS-G1 were significantly enriched in 5 g/L glucose concentration, compared with 10 g/L glucose concentration. In addition, The present study identified its regulation pattern and key genes under the low glucose environment (7 mRNAs, 16 sRNAs). This study primarily investigates the variances in the regulatory pathways of oligotrophic bacteria BS-G1, which holds substantial importance in comprehending the mechanism underlying the limited sugar tolerance of oligotrophic bacteria.

Regulatory monitoring networks are often too sparse to support community-scale PM2.5 exposure assessment while emerging low-cost sensors have the potential to fill in the gaps. Recent advances in air quality monitoring have produced portable, easy-to use, low-cost, sensor-based monitors, which has given a new dimension to the air pollutant monitoring and has democratized the air quality monitoring process by making monitors and results directly available at community level. This study used PurpleAir(c) sensors for PM2.5 assessment in California, USA. Evaluation of PM2.5 from sensors included Quality Assurance &amp; Quality Control (QAQC) procedures, assessment with respect to reference monitored PM2.5 concentrations, and formulation of a decision support system integrating these observations using geostatistical techniques. The hourly and daily average observed PM2.5 concentrations from PurpleAir monitors followed the trends of observed PM2.5 at regulatory monitors. PurpleAir monitored PM2.5 also captured the peak PM2.5 concentrations due to incidents like forest fire. In comparison with reference monitored PM2.5 levels, it was found that PurpleAir PM2.5 concentrations were mostly higher. The most important reason for PurpleAir higher PM2.5 concentrations was the inclusion of moisture or water vapor as aerosol in contrast to measurements of PM2.5 excluding water content in FEM/FRM and non-FEM/FRM monitors. On long term assessment (2016-2020), R2 was between 0.54 and 0.86 at selected collocated PurpleAir and regulatory monitors for hourly PM2.5 concentrations. Past research studies have been conducted for mostly shorter time periods (&lt;3-4 months) that resulted in higher R2 values between 0.80 to 0.98. This study aims to provide reasonable estimations of PM2.5 concentrations with high spatiotemporal resolutions based on statistical models using PurpleAir measurements. The methods of Kriging and IDW, geostatistical interpolation techniques, showed similar spatio-temporal patterns. Overall, this study revealed that low-cost, sensor based PurpleAir sensors could be effective and reliable tools for episodic and long-term ambient air quality monitoring.

Most of the fishing currently practiced in Japan is done by small vessels with a small number of fishermen (one or two). One of the most common fishing methods is longline fishing. However, this method requires the vessel to operate at a constant low speed because the depth of the hook must be kept constant while adjusting the speed of the fishing boat to the tidal current. In addition, because the vessel must maneuver and fish at the same time, automation is desired. Thus, we propose a robotic system that can control the depth of the trap at a constant depth even when the speed of the vessel and the current change, and that can successfully fish without the need for skilled fishermen. Fishing can be conducted regardless of the speed of the vessel, whereas currently it is controlled by the speed of the vessel and the tidal current. Therefore, it may contribute to proposing new fishing methods as well as the existing ones. This can contribute to the shortage of successors to the fishing industry and to the revitalization of the fishing industry.

The purpose of this project was to demonstrate the potential of converting an existing internal combustion engine for hydrogen operation at relatively low cost and to optimize the combustion process for ultra-low NOx emissions. The conversion has been carried out on a 450cc naturally aspirated single cylinder engine. The first baseline measurements and setup have shown lower NOx emissions than the baseline gasoline engine (without catalytic converter) for similar power output and engine efficiency. Further optimization of the combustion process allowed to achieve Euro VI and (latest European Commission proposal) Euro VII heavy-duty NOx limits without exhaust gas aftertreatment system (EATS) in steady state conditions. The concept is very promising and the knowledge gained should allow for further optimization to achieve near zero NOx emissions at high engine efficiency and power output with supercharging. It should also allow an efficient conversion of other engine types for different applications. In particular, a project with the aim to convert a heavy duty 6 cylinder engine intended for public transport buses has started. It follows a feasibility study which has shown the competitiveness of the hydrogen engine for this application.

The paper explores the potential of a low-cost advanced video-based technique for the assessment of structural damage induced to buildings by seismic loading. A low-cost high-speed video camera was utilized for motion magnification (MM) processing of footages of a two-story reinforced concrete frame building subjected to shaking table tests. The damage after seismic loading was estimated by analyzing the dynamic behavior (i.e. in terms of modal parameters) and the structural deformations of the building in the MM videos. The results by MM were compared for method validation to damage assessment obtained by the analyses of conventional accelerometers and high-precision optical markers tracked by a passive 3D motion capture system. Also, 3D laser scanning to obtain an accurate survey of the building geometry before and after the seismic tests was carried out. In particular, accelerometers were also processed and analyzed by using several stationary and non-stationary techniques with the aim to analyze the linear behavior of the undamaged structure and the nonlinear structural behavior during damaging shaking table tests. The proposed MM-based procedure provided accurate estimate of the main modal frequency and the damage location through the analysis of modal shapes, which were confirmed by advanced analyses of accelerometric data.

Methane is the main cause of sewer explosion accidents, and the available monitoring methods mainly use portable gas sensors for on-site detection. However, these methods cannot grasp the dynamic changes in methane in a sewer in real time or make better predictions of methane explosion accidents. Here, we present a low-power online monitoring system for sewer methane in order to ensure the safety of urban sewers. A low-power ultrasonic gas sensor was used to monitor the methane content in biogas. Due to the impacts of changes in CO2, temperature, and humidity in the sewer on the ultrasonic methane measurement results, a corresponding compensation method was proposed. The effectiveness of the compensation method was verified through experiments, which measured the methane concentration under different influences, and the methane values measured before and after compensation were compared. The power consumption was only 1.28 mW if the system worked in intermittent operation mode, and it could operate for about 1.5 years by selecting a lithium battery with a capacity of 5 A · H. The experimental results showed that the gas detection accuracy could meet the commercial requirements and had a high compensation for the impacts of carbon dioxide, temperature, and humidity.

The goal of classroom English instruction is to educate students on how to use the English language effectively for communication in any scenario. It is identified by presenting various teaching tactics and speaking activities to encourage students to participate more actively in conversations. The study intended to identify the problems in the speaking performance of Grade 8 Jade in Tagum City National High School. The study was conducted using a quantitative non-experimental descriptive survey method. Results revealed that the problems in speaking performance have garnered a mean of 3.20 (moderate) as descriptive equivalent and it was found out that the prevailing speaking problem is anxiety with a mean of 3.84, interpreted as high. Thus, an intervention program is designed to address the problems in the speaking performance of the respondents. This program is divided into two: Overcoming Speaking Anxiety Seminar-Workshop and Speaking Enhancement Activities.

Low back pain is a common problem in the active population, and the second reason for visiting a physician. In patients with lumbar disc protrusion, the nucleus pulposus bulges against the disc and the latter protrudes into the spinal column, but the annulus fibrosus remains intact. The purpose of this study was to prove that starting an early complex rehabilitation treatment results into pain and disability reduction, and increased muscle strength and mobility in patients with lumbar disc protrusions. We performed a prospective cohort study, enrolling 60 patients (25 men and 35 women) aged between 26 to 76 years, diagnosed with lumbar disc protrusion. Patients in the experimental group registered significant improvements in all studied variables (pain, mobility, muscle strength, disability) after 6 months of treatment. The results of our study suggest that, in the lumbar disc disease, a combined rehabilitation program may be more effective in terms of pain and disability reduction, if it starts early after diagnosis. The current study proves the importance of combining electrotherapy with hydrotherapy and physical therapy. Patients who received this treatment combination showed an extremely significant improvement in pain relief, and reduction of functional disability after 6 months of treatment.

Pepper plants experience complex environmental factors including abiotic and biotic stresses in field and the importance of climate changes including low and high temperatures has been emerged. Low temperature stress in the growth and development is one of the most critical issues, which directly impact on the crop yield and productivity of pepper plants. It is essential to select and breed low temperature-(LT) tolerant pepper (Capsicum annuum L.) cultivars. The research was performed to assess the agronomical traits of 39 pepper accessions belonging to chili and bell fruit types which cultivated two different night temperature set-points at 15°C for suboptimal temperature (CT) and at 10°C for low temperature (LT), respectively. Plant heights (PH) of most pepper accessions in LT were significantly decreased compared to those in CT. The stem diameter (SD) and the length of main axis (LMA) were various depending on the genotypes under LT. Moreover, the number of flowers (NFL), the total number of fruits (NFR), fruit yield (FY), fruit fresh weight (FFW), fruit length (FL), fruit diameter (FD), and the number of seeds in a fruit (NSF) were notably declined in LT compared to CT. The evaluated agronomical traits between LT and CT were further applied for the correlation analysis, the principal component analysis (PCA), and the hierarchical cluster analysis. Notably, FY trait was correlated with other reproductive traits including NFR, FFW, FD, and FL on positive directions and LT treated-39 pepper accessions were clustered into seven groups by the clustering analysis. The selected accessions were primarily involved with the positive trends with the reproductive index including NFR, FL, FD, and FW traits and would be used for pepper breeding programs on developing LT-tolerant cultivars.

(1) Background: Although manual therapy for pain relief has been used as an adjunct in treatments for chronic low back pain (CLBP), there is still the belief that a single session of myofascial release would be effective. This study aimed to investigate whether a single session of a specific technique reduces pain and disability. (2) Methods: This was a crossover clinical trial in which 41 participants over 18 years old with CLBP were randomly enrolled into 3 situations - experimental, placebo, control, in a balanced and cross-over manner. The subjects underwent a single session of myofascial release on thoracolumbar fascia and compare it with the control and placebo. Outcome were pain and functionality, evaluated using the numerical pain rating scale (NPRS), pressure pain threshold (PPT) and Oswestry (ODI). (3) Results: There was no effects between-, within-tests, and interaction for all the outcomes, i.e., NPRS (η 2 = 0.32, F = 0.48, p = 0.61), PPT (η2 = 0.73, F = 2.80, p = 0.06), ODI (η 2 = 0.02, F = 0.02, p = 0.97). (4) Conclusion: A single trial of thoracolumbar myofascial release technique was not enough to reduce pain and disability in subjects with CLBP.

Background: To examine the association between income levels and mortality rates in patients with chronic kidney disease. Methods: We analyzed data obtained from 3,172 patients with chronic kidney disease obtained from the Korean National Health Insurance claims database (2003–2009). Each patient was monitored until December 2010 or until death, whichever came first. Individual income was estimated from the national health insurance premium. Information on mortality was obtained from the Korean National Statistical Office. Cox proportional hazard models were used to compare mortality rates between different income groups after adjusting for possible confounding risk factors. Results: A low income was significantly associated with a high mortality rate after adjusting for covariates (adjusted HR 1.298 [1.082–1.556]). In addition, dialysis patients who had low incomes were more likely to have higher mortality rates compared to those in dialysis patients who had high incomes (adjusted HR 1.528 [1.122–2.082]). Conclusion: The findings of this study indicate that chronic kidney disease patients with low incomes have the highest mortality risk. Promotion of targeted policies and priority health services for patients with low incomes may help reduce the mortality rate in this vulnerable group.

To achieve efficient utilization of low-concentration mine gas, reduce resource waste, and alleviate environmental pollution, high-temperature oxidation of low-concentration gas at a concentration range of 1.00% to 1.50% that is directly discharged into the atmosphere during coal mine production was oxidized to recover heat for reuse. The gas oxidation equipment was improved for the heating process, and the safety of low-concentration gas oxidation under high-temperature environment was evaluated. Experimental results showed that the reactor could provide a 1000 ℃ high-temperature oxidation environment for gas oxidation after installing high-temperature resistant ceramics. The pressure variation curves of the reactor with air and different concentrations of gas were similar. Due to the thermal expansion, the air pressure slightly increased and then returned to normal pressure. In contrast, the low-concentration gas exhibited a stable pressure response in the high-temperature environment of 1000 ℃. The outlet pressure was significantly greater than the inlet pressure, and the pressure difference between the inlet and outlet exhibited a trend to increase with the gas concentration. The explosion limit varied with the temperature and the blend with oxidation products. The ratio of measured gas pressure to air pressure after oxidation was below the explosion criterion, indicating that the measured concentration gas is still safe after the shift of explosion limit, which provides a safe concentration range for efficient use of low-concentration gas in the future.

The establishment of low carbon assessment initiatives is a crucial task especially at the city level. The determination of which source of carbon contributed more require robust data set and strategic approach. Hence, by using the campus as a small city approach, the establishment of carbon assessment and its’ reduction initiatives was required to keep track of the hotspot of the carbon source. The substantial amount of carbon source from campus operations such as energy consumption in the building, waste generation, and water consumption were identified. Moreover, as institutions of higher education, the execution of low carbon campus was initiated structurally involves the triangulation of research activities, teaching & learning and as well as campus operations or known as campus living lab approach. The application of low carbon cities framework, LCCF and assessment system enables to strategize the low carbon campus initiatives through the use of carbon footprint concept and the LCCF carbon track.

This paper deals with a non-contact method to identify the aerodynamic propeller parameters of the Parrot AR.Drone quadrotor. The experimental set consists in a camera recording the vehicle flights, the audio signal is extracted and is used a spectrogram analysis to estimates the propeller velocity. First, the aerial vehicle takes off and starts a hovering maneuver. The experiment is repeated with different additional masses attached to its rigid body. If the weight over the UAV increases/decreases, then the propeller must rotates faster/slower to produce a higher/lower thrust, and consequently, the sound frequency increases/decreases. Finally, this proposition is validated experimentally, and the estimated velocity is used to identify the quadrotor thrust parameters.

Introduction: We investigated the potential effect of smoking on pathological staging in clinically low-risk patients. Material-Methods: Data of 59 patients who were diagnosed with a bladder tumor for the first time and had a single lesion radiologically and endoscopically smaller than 3 cm were investigated, retrospectively. A total of 33 patients who currently smoke or smoked were classified as ever smokers group and 26 patients who did not ever smoke were classified as never smokers group. Pathological diagnoses of the patients in both groups were compared. Results: A total of 9 patients (27.3%) in ever smokers group and 18 patients (69.2%) in never smokers group had Ta disease (p<0.05). Morover, 19 patients (57.6%) in ever smokers group and 5 patients (19.2%) in never smokers group had T1 disease (p<0.05). The number of patients with low grade (LG) tumor were 8 (24.2%) and 19 (73.1%) in ever smoking and never smoking groups, respectively (p<0.05). The number of patients with high grade (HG) tumor were 25 (75.8%) and 7 (26.9%) in ever smoking and never smoking groups, respectively (p<0.05). Ta HG was detected in 9 (27.3%) patients in ever smoking group. In contrast, no patients in never smoking group had Ta HG disease (p<0.05). The number of patients with T1 HG was 17 (51.5%) in ever smoking group and 2 (7.69%) in never smoking group (p<0.05). Conclusion:Smoking seems to associate with pathologically worse stage and grade in patients with primary, single, < 3cm bladder cancer.

AbstractWe investigated the effect of cigarette smoking on pathological staging in clinically low-risk patients. Data of 59 patients who were diagnosed with bladder tumor for the first time and had a single lesion radiologically and endoscopically smaller than 3 cm were investigated retrospectively. 33 patients who smoked were classified as Group I, and 26 patients who did not smoke were classified as Group II. Pathological diagnoses of the patients in both groups were compared. The mean age of the patients were 64.8 (20–86) years. In Group II, 5 (19.2%) were female and 21 (80.8%) were male (p < 0.05). Nine patients (27.3%) in Group I and 18 patients (69.2%) in Group II had Ta disease (p < 0.05). Nineteen patients (57.6%) in Group I and 5 patients (19.2%) in Group II had T₁ disease (p < 0.05). The number of patients with low grade (LG) tumor were 8 (24.2%) and 19 (73.1%) in Group I and in Group II, respectively (p < 0.05). The number of patients with high grade(HG) tumor were 25 (75.8%) and 7 (26.9%) in Group I and in Group II, respectively (p < 0.05). TaHG was detected in 9 (27.3%) patients in Group I. In contrast, no patients in Group II had TaHG disease (p < 0.05). The number of patients with T₁HG was 17(51.5%) patients in Group I and 2 (7.69%) patients in Group II (p < 0.05). Smoking is associated with pathologically HG and stage in patients with first time bladder tumor which is single and smaller than 3 cm.

Hyper-radiosensitivity (HRS) is the increased sensitivity to low doses of ionizing radiation observed in most cell lines. We previously demonstrated that HRS is permanently abolished in cells irradiated at a low dose rate (LDR), in a mechanism dependent on transforming growth factor β3 (TGF-β3). In this study, we aimed to elucidate the activation and receptor binding of TGF-β3 in this mechanism. T-47D cells were pre-treated with inhibitors of potential receptors and activators of TGF-β3, along with addition of small extracellular vesicles (sEVs) from LDR primed cells, before their radiosensitivity was assessed by the clonogenic assay. The protein content of sEVs from LDR primed cells was analyzed with mass spectrometry. Our results show that sEVs contain TGF-β3 regardless of priming status, but only sEVs from LDR primed cells remove HRS in reporter cells. Inhibition of the matrix metalloproteinase (MMP) family prevents removal of HRS, suggesting an MMP-dependent activation of TGF-β3 in the LDR primed cells. We demonstrate a functional interaction between TGF-β3 and activin receptor like kinase 1 (ALK1), by showing that TGF-β3 removes HRS through ALK1 binding, independent of ALK5 and TGF-βRII. These results are an important contribution to a more comprehensive understanding of the mechanism behind TGF-β3 mediated removal of HRS.

The goal of this paper is to present a low-cost, low-power prototype of a pulsed Ultra Wide Band UWB) oscillator and an UWB elliptical dipole antenna integrated on the same Radio Frequency (RF) Printed Circuit Board (PCB) and its digital control board for Real Time Locating System (RTLS) applications. The design is compatible with IEEE 802.15.4 high rate pulse repetition UWB standard being able to work between 6 GHz and 8.5 GHz with 500 MHz bandwidth and with a pulse duration of 2 ns. The UWB system has been designed using the CST Microwave Studio transient Electro-Magnetic (EM) circuit co-simulation method. This method integrates the functional circuit simulation together with the full wave (EM) simulation of the PCB’s 3D model allowing fast parameter tuning. The PCB has been manufactured and the entire system has been assembled and measured. Simulated and measured results are in excellent agreement with respect to the radiation performances as well as the power consumptions.

Following the detection of highly pathogenic avian influenza (HPAI) virus in countries bordering Kenya to the west, we conducted surveillance among domestic and wild birds along the shores of Lake Victoria. In addition, between 2018 and 2020, we conducted surveillance among poultry and poultry workers in live bird markets and among wild migratory birds in various lakes that are resting sites during migration to assess introduction and circulation of avian influenza viruses in these populations. We tested 7,464 specimens (oropharyngeal and cloacal swabs) from poultry and 6,531 fresh fecal specimens from wild birds for influenza A viruses by real-time RT-PCR. Influenza was detected in 3.9% (n=292) of specimens collected from poultry and 0.2% (n=10) of fecal specimens from wild birds. On hemagglutinin subtyping, most of the influenza A positives from poultry (274/292, 93.8%) were H9. Of 34 H9 specimens randomly selected for further subtyping, all were H9N2. On phylogenetic analysis, these viruses were genetically similar to other H9 viruses detected in East Africa. Only two of the ten influenza A positive specimens from the wild bird fecal specimens were successfully subtyped; sequencing analysis of one specimen collected in 2018 was identified as low pathogenicity avian influenza H5N2 virus of the Eurasian lineage and the second specimen, collected in 2020, was subtyped as H11. A total of 18 OP/NS swabs from poultry workers with ARI (12%) were collected; none were positive for influenza A virus. We observed significant circulation of H9N2 influenza viruses in poultry in live bird markets in Kenya. During the same period, low pathogenic H5N2 virus was detected in a fecal specimen collected in a site hosting a variety of migratory and resident birds. Although HPAI H5N8 was not detected in this survey, these results highlight the potential for introduction and establishment of highly pathogenic avian influenza viruses in poultry populations and the associated risk of spillover to human populations.

Frequently Asked Questions (FAQs) systems rely on semantic symmetry similarity measuring between two sentences. To address the challenges of insufficient training data and limited domain-specific understanding in low-resource FAQs, this paper proposes a general framework, PDAMF-FAQ, to solve these issues. Firstly, we propose a paraphrasing-based data augmentation model that integrates syntactic information and edit vectors. Using a rule-based approach, it retrieves template sentences from a corpus and masks relevant words with special characters. Edit vectors between the original and paraphrase sentences are added to a pre-trained model's encoding layer to enhance the model's ability to learn the differences between the original and reference paraphrase sentences. Additionally, this paper presents a mixed-feature semantic matching model based on SimBERT. The model extracts keyword features from the text, replacing these keywords with special characters to construct intent features. These intent features, along with the user question and keyword features, are then concatenated to form the model's input. Experiments were conducted respectively on the paraphrasing-based data augmentation model, mixed-feature semantic matching model and their comprehensive application in a low-resource domain-specific FAQ. The experimental results show that the proposed framework effectively improve the performance of domain-specific FAQ system.

With the widespread use of new equipment such as distributed photovoltaics, distributed energy storage, electric vehicles, and distributed wind power, the control of low-voltage distribution networks (LVDNs) has become increasingly complex. Acquiring the most recent topological structure is essential for conducting accurate analysis and real-time control of LVDNs. The signal-injection-based topology identification algorithm is favored for its speed and efficiency. This study proposes a new signal-injection-based topology identification algorithm aimed at solving the issues of reduced completeness and correctness of identification caused by missing feature signal records (FSRs). By analyzing the correlations between FSRs of different positions, the algorithm employs vertical and horizontal completion methods to effectively address missing data, combined with inclusion detection algorithms, to identify the topology of LVDNs. Based on the study of actual LVDN data, the results indicate that the algorithm not only significantly improves the completeness and correctness of topology identification for LVDNs but can also increase the number of devices in operation by evaluating the status of topological equipment, further enhancing the topology identification performance.

In the process of climate change mitigation and adaptation, the focus on climate risk driven by transition innovations has received widespread attention from governments, regulators, and investors. Based on the identification of low-carbon patents through the Green and Low-carbon Technology Inventory in China, this study constructs low-carbon innovation measurements of listed firms in China from 2015 to 2021. Then, an empirical model is used to investigate the impact and mechanism of climate transition innovations on the default risk. The baseline regression model shows that low-carbon innovations can mitigate the default risk of listed firms. Moreover, our findings are supported by instrumental variable regressions that use the time costs of innovation. Finally, the mediation effect demonstrates that investor attention, total factor productivity, and technology spillovers are paths through which transition innovations can affect the default risk. This study reveals that low-carbon technological advances have a positive effect on climate transition risks.

This review provides a comprehensive and updated information on chalcones, presenting their sources, methods of identification and properties putting emphasis on applications in agricultural industry. Vast exploitation of synthetic pesticides led to the weed and pest resistance issue, causing economic loss but more importantly health risk due to pesticide overuse. Because one of the aim of the European Green Deal 2030 is the Farm to Fork strategy which targets on reducing by 50% the use of chemical pesticides by 2030, and push towards natural pesticides which are more environmentally friendly and restore natural resources, chalcones and their derivatives seem to fit perfectly. They have herbicidal, fungicidal, bactericidal and antiviral properties. Moreover, chalcones are naturally occurring substances, known for their favorable health effect for years, working on many areas. This review is complementary to the previous ones describing chalcones use in agriculture, updates them but additionally shows methods of detection.

Public housing stock, called Social Housing, in Italy developed between the 1950s and the 1980s. As of today, the first residential developments are almost nearing their end-of-life age, in need of urgent and intensive renovation. The European Commission, with the Renovation Wave, has set a goal of doubling the rate of building renovation over the next 10 years, reducing emissions, improving energy performance, and promoting decarburization. Renovation interventions, including structural, functional, energy, plant upgrading, etc., are to be preferred over integral demolition and reconstruction interventions, which have significant repercussions in terms of managerial and social discomfort. The case studies examined concern renovation interventions aimed at energy efficiency, functional adaptation of housing as well as facade restyling. The design variants analyzed were evaluated in terms of CO2e emissions, according to LCI (Life Cycle Inventory) and EPD (Environmental Product Declaration) approaches. This approach has a twofold purpose: to propose design guidelines, with low CO2e emissions, through hypotheses of variants to the case studies, and to propose, to the Economic Operators, economically advantageous bidding scenarios, in the procurement process.