There is a growing awareness of the detrimental environmental impact of the construction industry, primarily due to the utilization of building materials that necessitate energy-intensive processes for their production. The objective of this paper is to explore whether mixing wood and cement could serve as a viable solution to mitigate this adverse environmental effect. The data was obtained by extensively investigating the Clarivate Web of Science database, adhering to the PRISMA technique guidelines, and subsequently processed using Bibliometrix and VOSviewer software. An in-depth critical analysis of the literature revealed a heightened interest in this subject matter in recent years, with the focal points evolving from initial experimental endeavors aimed at understanding the behavior of the innovative wood cement composites, primarily in terms of their mechanical properties, to assessing their environmental impact and the advantages associated with their use. The researchers suggest that optimal results can be achieved by treating the wood with tetraethyl orthosilicate, incorporating cellulose nanocrystal particles or wollastonite into the mixture, and utilizing wood from the Pinus species. Furthermore, it was discovered that a noticeable improvement in strength is only attainable if a low percentage of wood, up to 30%, when wood ash is employed. Ongoing research concerning wood and cement composites continues to progress, with regular advancements and breakthroughs, thus offering promising prospects for the development of superior and eco-friendly building materials.

Keywords: Wood residuals; Forest biomass; Wood composite; Wood floor; Life Cycle Assessment.

House construction is a unique characteristic of the swamp lands in Banjarmasin. Foundations for swampy soil require special handling. The weakness of wood materials and the inability of wood pillar foundations to support building loads are the primary causes of building problems in these swampy areas. Mistakes in foundation construction often arise from the need to expand houses to two stories or renovations. The load-bearing capacity of the wood pillar foundations used is very limited. This study aims to determine the weaknesses of wood pillar foundations to address signs of damage in house construction on swamp land. Field observation research, including the examination of house buildings and individual objects, was conducted at several construction sites in Banjarmasin as part of this study. Data presentation is descriptive. The results indicate that weak wood pillar foundation construction is characterized by damaged piles and floor subsidence. The small size of the wood pillars also limits the load-bearing capacity. The presence of broken 'sunduk' elements is one of the causes of this foundation damage. This research provides new insights into the weaknesses of wood pillar foundations and offers repair recommendations to enhance the resilience and stability of buildings on swamp land.

The construction of a house with a stage structure is the uniqueness of Banjarmasin's swampland. Particularly, foundations for swampy terrain necessitate special handling. Building material defects and the basic inability to modify the use and design of wood pillar foundations are the main causes of house building problems. The very limited capacity of a wooden pillar foundation makes house buildings collapse frequently. The aim of the study is to determine the weaknesses of the wooden pillar foundations by examining the indications of damage to the house structure. Field observation investigations, including housing and individual object observations, will be carried out at multiple construction sites in Banjarmasin (Indonesia) as part of this study. The way the data is presented is descriptive. A wooden pillar foundation, which is a frequently used foundation, has a limited load bearing capacity. Because that, there has been no related research that addresses the issue of how this foundation damage. The aim of the study is to determine the early signs of swamp building collapse in the wooden pillar foundations weaknesses by examining the indications of damage to the house structure. The weak construction of a wooden pillar foundation explains some indications of house building damage, such as broken wooden pillars and floor settlement. The existence of evidence that there is a broken 'sunduk’ element is one of the causes of damage to this foundation

Bending of solid wood from European oak is one of the most demanding technological processes due to its specific structural and physical properties and variability. We investigated the influence of wood moisture content (MC) and stiffness, determined by NDT, as well as previous drying methods on the bending ability of the wood. The best quality was obtained with bending specimens bent at a moisture content of at least 16 % and quarter or semi-quartersawn. The number of rejected specimens increased slightly when HF bending was used. Single-stage predrying of oak to a final MC of 8 % resulted in a high rejection rate (> 70 %) regardless of drying technique. The acceptance rate was higher for less stiff specimens where the ratio of ultrasonic velocity in the straight (vS) and bent region (vB) was less than 0.5 (vB/vS).

One of the main products of the forest, which has the greatest economic impact, is wood. Due to its characteristics, the wood requires certain types of vehicles for transport it. For this reason, the accessibility of the stands with forest roads plays significant role in the efficiency of the wood logging process, which aims to bring the wood from the forest to the harvesting area located, frequently, next to a permanent transport route. The process of wood transport from the forest initially takes place on forest roads and after that on public roads. The technological process of wood transport represents an important stage in this process, and its good organization can have implications on the final price of the wood material. Based on those mentioned above, the paper aims to highlight the factors that can influence productivity in the case of loading wood in forestry trucks and forestry platforms, in different conditions. Thus, the research was carried out in four counties in Romania and addressed the loading of wood in different forestry trucks and platforms, with or without trailers. Following the evaluation of the work phases specific to the process of round wood loading in vehicles of transport, it was found that sometimes a significant importance is given to the working phases that can be carried out before the loading process, as phases of preparation of the wooden material in order to load it. Also, the facilities of the transport vehicles, the assortments of wood material, as well as the experience of the operators are the main factors that can lead to an increase in productivity.

Introduction: The construction of a house with a stage structure is the uniqueness of Banjarmasin's swampland. Particularly, foundations for swampy terrain necessitate special handling. Building material defects and the basic inability to modify the use and design of wood pillar foundations are the main causes of house building problems. The very limited capacity of a wooden pillar foundation makes house buildings collapse frequently. Purpose of the study: The aim of the study is to determine the weaknesses of the wooden pillar foundations by examining the indications of damage to the house structure. Methods: Field observation investigations, including housing and individual object observations, will be carried out at multiple construction sites in Banjarmasin (Indonesia) as part of this study. The way the data is presented is descriptive. Result: The weak construction of a wooden pillar foundation explains some indications of house building damage, such as broken wooden pillars and floor settlement. The existence of evidence that there is a broken 'sunduk’ element is one of the causes of damage to this foundation. The small size of the wooden poles also makes the load-bearing capacity limited.

Fast-growing teak is widely cultivated in Indonesia to address the supply and demand of teak trees. However, efforts still need to be made to evaluate the condition of standing teak trees during their growth period. Studies on nondestructive testing (NDT) of wood based on electrical properties through dielectric spectroscopy (DS) are recently being developed, especially for standing tree evaluation. The study aimed to analyze the dielectric value of a fast-growing standing teak tree at frequency ranges 250 kHz – 60 MHz and to understand the relationships between physical and anatomical properties. Dielectric spectroscopy data were collected directly on the trees 4, 5, and 7 years old using a capacitance measurement system. Meanwhile, physical and anatomical samples were taken using a Ø 0.5 cm increment borer. The results showed that fiber length (FL), lumen diameter (LD), and fiber wall thickness (FWT) were significantly different at each tree age. This research found the optimal dielectric frequency to discriminate the wood properties in standing trees. There is a weak relationship (R= 0.2) in predicting the anatomical wood properties, while moderate to strong relationships (R= 0.4 to R= 0.8) are found in predicting wood density based on the selected frequency and moisture content variables. Further analyses and data processing can be improved by finding significant variables in the capacitance measurement system.

Deadwood represents a source of nutrients, carbon and water for metabolism within forest ecosystem. Nutrients are mobilized due to the decomposition of wood, which is a long-term process that can be best studied by analysing environmental data on a temporary scale. Our study provides physico-temporal data on the downed logs of three major tree species in European temperate forests: Abies alba Mill., Fagus sylvatica L. and Picea abies (L.) Karst. Time since death was obtained using tree censuses (repeated for 40 years) and dendrochronology for each single downed log, the oldest being 75 years old. Standard laboratory methods were used for the determination of wood density and moisture changes. F. sylvatica was decomposed rapidly in the initial phase – mass loss was 50% during the 5 years after death, while A. alba and P. abies lost 13% and 16%, respectively. Downed logs of F. sylvatica contained 391 kg of water per m³, while these of P. abies 279 kg. A log-transformed linear model was created that shows the dependence of time since death on mass loss. According to the model, F. sylvatica had the shortest total decomposition time (39 years), followed by A. alba (58 years) and P. abies (86 years).

Bent trees have been observed during the early years in juvenile plantations (less than 5 years-old) of Tectona grandis in Costa Rica. The relationship between bending and the morphological characteristics of the trees was explored. An evaluation of bent trees was conducted in six juvenile plantations (8, 17, 27, 28, 31, and 54 months old) of Tectona grandis. Site 1 with 8-month-old plantations did not display any relationship with any tree morphological variable (diameter, height, and crown weight of tree), whereas for the sites 2, 3, and 4 with 17-, 27-, and 28-month-old plantations, respectively, all the tree morphological variables were statistically correlated with the bent trees. A multiple regression analysis showed that the most influential variables were height to crown base, crown weight, diameter, and total height of the tree. An evaluation of the bending risk factor (RF) was correlated with the height to crown base, crown weight, and form factor. The modulus of elasticity and chemical compositions of bent trees differed from those of straight trees. The causes of tree bending are complex, involving, among other factors, the morphology of the trees, plantation conditions, and other factors specific to the xylem, such as the specific gravity, modulus of elasticity, and presence of calcium and magnesium in the wood.

Tree decline resulting from climate change results in physiological weaknesses, attack by harmful pests and pathogen, and threatens forest ecosystem stability. In the work described here, the effects of drought on wood density, tree ring width, and variations in vessel morphology were investigated in Persian oak (Quercus brantii) in the forests of the Zagros Mountains, Ilam province, western Iran. Radial discs were cut from trunks of declined and healthy trees and wood blocks cut radially from the sapwood, heartwood, and juvenile core. Observations were made on transverse sections from the blocks using microscopy. In trees with decline symptoms, wood density was greater than the healthy trees. Furthermore, declining trees had the narrowest ring width, reduced vessel diameter, vessel area, and highest number of vessels and tylose in pith towards bark. It was concluded that changes in anatomical features are associated with the weakening of the trees and are components in declining tree health.

Wood is very susceptible to the action of biotic agents. There is a growing interest in the protection of wood and wood artworks to extend their life, using environmentally friendly preservatives. The aim of this paper was the study of nano/siliconate impregnation system for wood protection to control biological colonization. The biotic agents studied have been wood decay fungi. In conclusion, this paper has shown that all the treatments have presented an excellent protective performance against biotic agents. Is important to mention that a synergistic effect can be observed when generating the siliconate/nanoparticle mixtures, resulting in protective systems with excellent efficiency for all the degrading agents. Moreover, it presents an easy application, which represents not only a watertight protective system, but also a set of systems that may be used and managed according to the availability of the active components, the costs, and, most importantly, without having to modify the form of application.

This study examines the latest innovation in wooden pile foundation models using a combination of wood and concrete materials for house construction on swampy land. The focus of the research is on developing joints and materials that enhance the load-bearing capacity and stability of building structures on swampy terrain. The methods used include field observations, laboratory experiments, and descriptive analysis. The results show that the combination of wood and concrete in foundation piles can increase structural strength, reduce deformation, and extend the service life of buildings. The new joint techniques developed in this research are effective in improving structural integrity and minimizing the negative impacts of soft soil conditions. The conclusion emphasizes the importance of material innovation and joint techniques in construction on swampy land, providing practical guidance for construction practitioners and researchers in this field.

The study findings revealed significant variability in various wood properties among different genetic families, although the static modulus of elasticity did not exhibit significant differences between the chosen genetic families. All measured wood properties decreased from the bottom to the top of the model trees. Wood hardness displayed a moderately negative correlation with wood density and weak correlations with MOE and MOR. Given the weak correlations between wood hardness and other wood mechanical properties, it is suggested that the MOEdyn would be a more suitable trait for genetic studies.

The distribution of Mexican Magnolia species´ occur under restricted climatic conditions. As many other tree species from the tropical montane cloud forests (TMCF), Magnolia species appear to be sensitive to drought. Through the use of dendrochronological techniques, this study aims to determine the climate influence on the vessel traits of M. vovidesii and M. schiedeana which are endangered tree species that are endemic to the Sierra Madre Oriental in eastern Mexico. Because most of the tree species in TMCFs are sensitive to climate fluctuations, it is necessary to investigate the differences in the climatic adaptability of the vessel architecture of these trees. This could allow us to further understand the potential peril of climate change on TMCFs. We compared vessel frequency, length and diameter in drought and non–drought years in two Mexican Magnolia species. We used tree–rings width and vessel traits to assess the drought effects on Magnolias’ diffuse–porous wood back to the year 1929. We obtained independent chronologies for M. vovidesii with a span of 75 years (1941–2016), while for M. schiedeana we obtained a span of 319 years (1697–2016). We found that temperature and precipitation are strongly associated with differences in tree–ring width (TRW) between drought and non–drought years. Our results showed anatomical differences in vessel trait response between these two Magnolia species to climatic variation. We suggest that our approach of combining dendroclimatic and anatomical techniques is a powerful tool to analyse anatomic wood plasticity to climatic variation in Magnolia species.

Understanding maturation stress and wood properties of poplar tension wood are critical for improving lumber yields and utilization ratio. In this study, Released Longitudinal Maturation Strains (RLMS), anatomical features, physical and mechanical properties, and nano-mechanical properties of the cell wall were analyzed at different peripheral positions and heights in nine inclined, 12-year-old poplar (Populus×euramericana ‘Zhonglin46’) trees. The correlations between RLMS and wood properties were determined. The results showed that there were mixed effects of artificial inclination on wood quality and properties. The upper sides of inclined stems had higher RLMS, proportion of G-layer, bending modulus of elasticity, and elastic modulus of cell wall but lower microfibril angle than the lower sides. At heights between 0.7 m and 2.2 m, only the double wall thickness increased with height, RLMS and other wood properties such as fiber length and basic density fluctuated or changed little with height. RLMS was a good indicator of wood properties in the tension wood area and at heights between 0.7 m and 1.5 m. The results of this study present opportunities to identify and select better quality wood in poplar trees.

Lignocellulosic biomass, an abundant and renewable resource, serves as a crucial raw material for the production of biofuels, biochemicals, and various value-added products. This paper aims to develop and optimize a mild alkaline treatment of sawdust assisted by ultrasound, along with enzymatic hydrolysis of the pretreated material. The sonochemical pretreatment with alkali emerged as the optimal approach to enhance the susceptibility of cellulose to subsequent enzymatic hydrolysis, thereby increasing the yield of reducing sugars. A comparative study was performed using various ultrasonic applicators (horn and bath) and conventional assisted alkaline pretreatment. The ultrasonic assisted pretreatment revealed a higher delignification as 68% (horn) and 57% (bath) comparing with conventional pretreatment. Processes were optimized using a statistical analysis based on a 23 factorial design. The ratio between sawdust and alkanine solution (RSL = 0.5–1.5 g/100 mL), US amplitude (A = 20–60%), and working temperature (t = 30–50 °C) were selected as process factors. The optimal operating conditions to maximize the reducing sugar yield (138.15 mg GE /gsubstrate) were found as following: solid/liquid ratio RSL,opt = 1.25 g/100 mL, US amplitude Aopt = 60%, and and pretreatment temperature topt = 50 °C. The overall outcomes clearly confirmed the intensification of delignification by ultrasound assisted alkaline pretreatment

In Nigeria, the adoption of sustainable biomass for energy generation is on the rise. One crucial factor that affects the efficiency of Biomass utilization is the moisture content. This study investigates the economic impact of moisture at different stages of the wood biomass distribution chain, considering the entire chain. The methodology employed includes a comprehensive literature review, interviews, and economic calculations. By analyzing these factors, this research aims to provide valuable insights into the economics of moisture in wood biomass, contributing to the sustainable development of the Biomass energy sector in Nigeria. Based on the outcomes of this investigation, it has been discovered that the costs associated with moisture content in Nigeria amount to approximately ₦500,000,00 (Five Hundred Thousand Naira only). Utilizing wood Biomass with a moisture content of 32% weight, as opposed to 18% weight, has proven to be more costly. Transportation contributes to a significant portion of this increase, while the reduction in burning efficiency accounts for the remaining half. To further elaborate on these findings, it is crucial to understand that the transportation costs are impacted by the additional weight and volume of biomass with higher moisture content. This necessitates the use of more fuel and resources during transportation, resulting in increased expenses. Additionally, the decreased burning efficiency associated with higher moisture content poses a challenge. It leads to reduced energy output and increased fuel consumption, ultimately impacting the overall economic viability of wood biomass as an energy source. By identifying these factors, this study aims to provide insights into the economic implications of moisture content in the wood biomass distribution chain in Nigeria. These findings can serve as a basis for developing strategies to optimize the use of biomass, reduce costs, and enhance the sustainability of the energy generation process. One of the most convenient and cost-effective solutions to reduce transportation expenses and improve combustion efficiency is through planned air drying of wood biomass. Large-scale power plants typically prefer utilizing wood biomass that has undergone air drying, resulting in a moisture content ranging from 18% to 36% by weight. By implementing planned air-drying techniques, the moisture content of wood biomass can be significantly reduced, thereby decreasing transportation costs. As the biomass becomes lighter and less bulky, transportation requirements are optimized, leading to enhanced efficiency and reduced expenses. Moreover, air-dried wood biomass offers improved combustion characteristics. The reduced moisture content allows for better heat transfer during the combustion process, resulting in higher energy output and increased fuel efficiency. This not only improves the overall economics of utilizing wood biomass but also contributes to a more sustainable and environmentally friendly energy generation system. The application of planned air drying in the wood biomass distribution chain in Nigeria can serve as a practical solution to address the economic challenges associated with moisture content. By adopting this approach, stakeholders can maximize the potential of wood biomass as a renewable energy resource while minimizing costs and promoting sustainable practices.

This study investigated the presence and characteristics of Juglans neotropica in three ecosystems in Southern Ecuador: Montane Evergreen Forest, Evergreen Seasonal Lower Montane Forest, and Semideciduous Foot Montane Forest. The main focus was on the species' multipurpose nature as both a fruit and timber source. Six study sites, totaling at least 0.5 hectares each, were established, with four in Loja province and two in Zamora Chinchipe province.The results showed significant differences in dendrometric variables across the sites, with the most favorable growth recorded in The Tundo, where trees exhibited an average diameter at breast height (DBH) of 45.16 cm, basal area (G) of 1.41 m2, total height (TH) of 19.22 m, canopy height (CH) of 13 m, cubic volume (CV) of 3.55 m3, and total volume (TV) of 5.22 m3. The species displayed a clumped distribution pattern, as indicated by a Morisita index greater than 1. Regarding abundance, the highest density of 297 trees per hectare was found in Argelia, while Victoria had the lowest density of 46 trees per hectare. This research highlights the importance of Juglans neotropica as a multipurpose species, providing both valuable fruits and wood resources in the studied ecosystems of Southern Ecuador.

The study was carried out in zone 7 of Ecuador, in ecosystems of the Southern Montane Evergreen Forest of the Eastern Cordillera of the Andes that goes from 2200 to 3000 masl. In the Evergreen Seasonal Lower Montane Forest of Catamayo-Alamor, which ranges from 1600-2000 meters above sea level and finally in the Semideciduous Foot Montane Forest of Catamayo-Alamor, which ranges from 400-1600 meters above sea level. The objective was to know the occurrence, structure and abundance of J. neotropica. The investigation consisted of collecting secondary information on the occurrence of the species, to later verify it in situ. Six sites with areas ≥ 0.5 hectares were identified, four in the province of Loja and two in the province of Zamora Chinchipe. Regarding the structure, it was determined that there are significant statistical differences as well as in the dasometric variables between one site and another, presenting better growths El Tundo with average values in DAP(cm)= 45.16; G(m2) = 1.41; HT(m)= 19.22; HC(m)= 13; VC(m3) = 3.55; VT(m3) = 5.22. Regarding the Morisita index, the species presents adistribution pattern >1. Regarding abundance, it was determined that Algeria presented a maximum of 297 (ind/ha), and La Victoria 46 (ind/ha) with a minimum.

This work presents the results of three connection types in double-shear with dowel fasteners, using the simplified equations from the Eurocode 5. All design parameters were established and compared using three different wood strength and density properties, which constitute the members connections. Eighty-one connections were obtained, allowing to conclude about the number of fasteners needed to the applied tensile load. An increase in the number of dowels was obtained with the increased applied tensile load, lower dowel diameter, lower wood density, and lower strength material in all connection types in the study. The design characteristic load-carrying capacity per shear plane and fastener also decrease with the previously considered parameters.

To examine the hydrophobicity of torrefied wood fuel, the water resistances of torrefied pellets prepared by two different methods were evaluated using exposure tests under indoor and outdoor conditions. Torrefied pellets from the xylem of Japanese cedar (Sugi, Cryptomeria japonica) and oak (Konara, Quercus serrata) were prepared by two methods: the torrefaction of wood chips followed by pelletization and the pelletization of wood chips followed by torrefaction. It was found that the pellets prepared by pelletization followed by torrefaction had much lower moisture levels than those prepared by the other method and they showed almost no change in diameter after an outdoor weathering test. These characteristics are unique and indicate that the pellets can be applied not only for industrial use but also for residential and commercial purposes.

The ultimate analysis parameters including carbon (C), hydrogen (H), nitrogen (N), and oxygen (O) content in biomass was rarely found to be predicted by nondestructive tests until to date. In this research, we developed partial least squares regression (PLSR) models to predict the ultimate analysis parameters of chip biomass using near infrared (NIR) raw spectra of non-wood and wood samples from fast growing tree and agricultural residue and nine different traditional spectral preprocessing techniques. These techniques include first derivative (sd1), second derivative (sd2), constant offset, standard normal variate (SNV), multiplicative scatter correction (MSC), vector normalization, min-max normalization, mean centering, sd1 + vector normalization, and sd1 + MSC. Additionally, we employed a genetic algorithm (GA), successive projection algorithm (SPA), multi-preprocessing (MP) 5−range, and MP 3−range to develop a PLSR model for rapid prediction. A dataset consisting of 120 chip biomass samples was utilized for model development in which the samples was non-wood samples of 65-67% and wood samples was 33-35%, and the model performance were evaluated and compared. The selection of the optimum performing model was mainly based on criteria such as the coefficient of determination in the prediction set (R2P), root mean square error of the prediction set (RMSEP), and the ratio of prediction to deviation values (RPD). The optimal model for weight percentage (wt.%) of C was obtained using GA−PLSR, yielding R2P, RMSEP, and RPD values of 0.6954, 1.1252 wt.%, and 1.8, respectively. Similarly, for wt.% of O, the most effective model was obtained using the multi-preprocessing PLSR−5 range method with R2P of 0.7150, RMSEP of 1.3088 wt.%, and RPD of 1.9. For wt.% of N, the optimal model was obtained using the MP PLSR−3 range method, resulting in R2P, RMSEP, and RPD values of 0.6073, 0.1008 wt.%, and 1.6, respectively. However, wt.% of H model provided R2P, RMSEP, and RPD values of 0.5162, 0.2322 wt.%, and 1.5, respectively. Notably, the limit of quantification (LOQ) values for C, H, and O were lower than the minimum reference values used during model development, indicating a high level of sensitivity. However, the LOQ for N, exceeded the minimum reference value, implying the samples to be predicted by the model must be in the range of reference range in calibration set. By scatter plot analysis, the effect of combined non-wood and wood spectra of biomass chips on rapid prediction of ultimate analysis parameters using NIR spectroscopy was investigated. To include different species in a model, the species have to be not only in the different values of the constituents to make a wider range for robust model but also they must provide their trend line characteristics in the scatter plot i.e. correlation coefficient (R), slope and intercept (same slope and slope approached to 1 and intercept is same (no gap) and approached zero, high R approached to 1). The effect of the R, slope and intercept to obtain the better optimized model were studied. The results show that the different species affected model performance of each parameter prediction in a different manner and by scatter plot analysis which of these species were affecting the model negatively and how the model could be improved was indicated. This is the first time of the effect is studied by the principle of scatter plot.

Material Flow Analysis (MFA) is a key tool in the circular bioeconomy, providing insight into the flow of materials within a system. Its use in the wood-based value chain is increasingly recognized and provides valuable information for policy making. Based on a comprehensive literature review, this article presents recent applications, challenges and research gaps related to MFA methodologies that are crucial for describing the expanding circular wood-based bioeconomy. Different MFA models and their methodologies are described and classified according to their scale and scope. The discourse on future research directions highlights the need to critically examine new material flows associated with bioeconomy development, including hidden by-product streams and end-use wood product recycling, as well as the role of regulators. The results of this study provide advice on data collection methods and the implementation of MFA models, offering valuable information for future research in the sector.

Hydrogen is increasingly recognized as a crucial element in the shift toward sustainable energy systems due to its high energy density and minimal environmental impact. Biomass, a renewable material derived from plants and animals, presents a promising feedstock for hydrogen production, offering both environmental and economic benefits. This paper examines diverse biomass resources for hydrogen production, including agricultural and forest residues, dedicated energy crops, and organic waste. It reviews key technologies for converting biomass to hydrogen, categorized into thermochemical, biochemical, and hybrid processes. Thermochemical methods like gasification and pyrolysis are discussed for their ability to handle varied feedstocks and produce high-purity hydrogen. Biochemical processes, such as anaerobic digestion and dark fermentation, are analyzed for their efficiency and lower operational costs. Hybrid approaches, which integrate multiple technologies, are explored for their potential to enhance system performance. Industrial applications of biomass-derived hydrogen are highlighted, including its use in transportation, power generation, the chemical industry, and heating. Future perspectives emphasize the need for advanced catalysts, process integration, sustainable feedstock sourcing, and supportive policies to drive commercial viability. The paper concludes by highlighting biomass’s significant promise in advancing sustainable energy systems and achieving global energy security and environmental goals.

Dispersion of antibiotic in livestock farming represents a health concern worldwide, contributing to the spread of antimicrobial resistant bacteria through animals, the environment, and humans. Phenolic compounds could be alternatives to antibiotics, once drawbacks such as low water solubility, bioavailability, and reduced stability are overcome. Although nano- or microsized formulations could respond to these shortcomings they do not represent cost-effective options. Here, three phenolic compounds, obtained from wood processing manufacturers, were characterized, revealing suitable features such as antioxidant activity, size, and chemical and colloidal stability for in-field applications. The Minimum Inhibitory Concentration (MIC) of these colloidal suspensions was measured against six bacterial strains isolated from livestock. These particles showed different inhibition behaviors: Colloidal chestnut was effective against one of the most threatening antibiotic resistant pathogens such as S. aureus but was ineffective toward E. coli. On the other hand, colloidal pine showed a weak effect on S. aureus but specificity toward E. coli. The present proof-of-concept points at colloidal polyphenols as valuable alternatives for antimicrobial substitutes in the livestock context.

Recycling upholstery textiles is challenging due to the complexity of materials, which often include a mix of fabrics, foams, and adhesives that are difficult to separate. The intricate designs and layers in upholstered furniture make it labor-intensive and costly to dismantle for recycling. Additionally, contaminants like stains, finishes, and flame retardants complicate recycling. Despite these difficulties, recycling upholstery textiles is crucial to reducing landfill waste and conserving resources by reusing valuable materials. It also helps mitigate environmental pollution and carbon emissions associated with producing new textiles from virgin resources. The presented research aimed to establish the feasibility of incorporating textile fibers from waste artificial leather fibers from the upholstery furniture industry into the structure of high-density fiberboards. This approach positively contributes to carbon capture and storage (CCS) policy and mitigates the problem of such waste being sent to landfills. The research shows that while selected mechanical and physical parameters of the panels decrease with a rising content of recycled textile fibers, it is possible to meet proper European standard requirements by adjusting technological parameters such as nominal density.

This study explores the perspectives and practices of architects regarding the reuse of wood in construction across five South-Central European countries: Slovenia, Serbia, North Macedonia, Bosnia and Herzegovina (BiH), and Montenegro. Based on a survey of architectural professionals, the research explores their attitudes, challenges, and motivations for using reclaimed wood, with a focus on circular construction principles. Key findings reveal unanimous agreement among re-spondents that both their profession and government entities inadequately support or promote wood reuse within the context of circular construction. While architects value reclaimed wood, there are country-specific variations. Environmental benefits, unique aesthetics, historical value, and sustainability are cited as primary motivators for reclaimed wood use. Additionally, re-spondents emphasize the ecological aspect as the most important consideration in wood product reuse, followed by economic and technological factors. Common concerns revolve around the long-term quality and maintenance of wood products. This research provides insights into the challenges and opportunities surrounding reclaimed wood use in South-Central Europe, high-lighting the need for support mechanisms and increased awareness to advance circular construc-tion practices in the region. These findings can have implications for architects and investors by identifying market opportunities, promoting eco-friendly practices, and providing valuable in-sights for future building designs with a focus on reclaimed wood elements within circular con-struction.

Seirogan, a wood creosote, is a nonprescription drug used to treat diarrhea. However, reports of its clinical use are rare. Here, we report on the efficacy of wood creosote (3 capsules daily) for the alleviation of diarrheal symptoms in 148 patients from 10 clinics in Japan. The wood creosote capsules were classified as remarkably effective (44 patients), effective (71 patients), and partially effective (13 patients) based on the degree of alleviation of diarrheal symptoms that were induced by a variety of causes. The antidiarrheal efficacy of the capsules did not differ between males and females, and young patients (21–30 years) showed greater improvement in diarrheal symptoms than did old patients (> 61 years). Although this report is based on the re-evaluation of old data that had been preserved by our company, the effectiveness and range of symptoms that were treatable with wood creosote has likely remained unchanged. To the best of our knowledge, this is the first public report on the clinical effectiveness of wood creosote capsules for the treatment of a wide range of diarrheal symptoms.

High level of noise is a disturbance to the human environment. Noise in industries is also an occupational hazard because of its attendant effects on workers’ health. Noise presents health and social problems in industrial operations, and the source is related to the machineries used in the industries. One of the unique features of the noise associated with wood machinery is the level of exposure and duration. Equipment used in a factory can be extremely loud. They can produce noise at decibels high enough to cause environmental health and safety concerns. The mechanically driven transport and handling equipment, cutting, milling, shaping and dust extractor installations in the wood industry generate noise. The sources of noise pollution have increased due to non-compliance with basic safety practices. The increased use of locally fabricated machine in the industry has increased the level of noise and vibration. The effects of industrial noise pollution as discussed include: increase in blood pressure; increased stress; fatigue; vertigo; headaches; sleep disturbance; annoyance; speech problems; dysgraphia, which means reading/learning impairment; aggression; anxiety and withdrawal. As presented in this paper, noise control techniques include; sound insulation, sound absorption, vibration damping and Vibration isolation.

Pilostyles, an endoparasitic genus within the Apodanthaceae family, grows inside host stems, with flowers and fruits being the only external manifestations. Previous studies of P. berteroi growing on Adesmia trijuga provided limited details of the endophyte and omitted the origin of flowers and synker structure. This study, using classical methods of optical microscopy applied to the analysis with scanning electron microscopy and confocal laser scanning microscopy, expands the understanding of the P. berteroi/A. trijuga complex. We find that P. berteroi develops isophasically with its host, forming meristematic patches between secondary phloem cells. The parasitized Adesmia stem’s cambium primarily produces inward parenchyma cells, with limited vessel production and ceased fiber formation. The polarization of meristematic patches led to the formation of floral meristems. Flowers develop endogenously and emerge by the breakthrough of the host stem. Flowers connect to the host cambium via chimeric synkers, combining P. berteroi parenchyma and tracheoids with Adesmia vessels. Unlike previous studies that show uniformity among Pilostyles species, our analysis reveals new insights into the structural interaction between P. berteroi and A. trijuga. Further ultrastructural investigations are needed to explore potential direct or indirect connections between the vascular systems of the two taxa.

The article is focused mainly on verifying the suitability of data from experimental milling heat-treated beech wood and on investigation of the effect of technical and technological parameters of milling on the energy consumption of this process. The independent parameters of machining process are cutting speed, feed speed, rake angle, and hydrothermal modification of experimental wood material. Based on analysis of variance it can be argued that the greatest statistically significant effect on energy consumption have cutting speed and rake angle of the tool while the feed speed had the least influence. The measured data of cutting power during milling were used to build a regression model and validate it, while the most suitable type of model with correlation of 87 % is Classification and Regression Tree followed by model created by Random Forests method.

Swampy land in Banjarmasin has special characteristics for building house constructions. The foundation for very low soil bearing capacity requires special treatment as well. Many building collapses are caused by foundation failures due to mismatched building loads and foundation functions, as well as construction material errors. The need for house design follows the development of building functions. Nowadays, a one-story house is no longer sufficient due to limited land. The need to elevate houses to two stories or to develop houses (renovations) often leads to foundation construction errors. The commonly used foundation, wooden pile foundation, has limited load-bearing capacity, necessitating modification steps in the form of foundation reinforcement. Several steps, including material combinations or combinations of various types of foundations, can be implemented. Therefore, a specific model is required to obtain a foundation design that can accommodate construction needs. The aim of the research is to create a foundation design model capable of reinforcing wooden pile foundations for both house construction development and as a reference for building one-story and two-story houses. In this research, field observations will be conducted at various house construction sites in Banjarmasin, both residential and individual objects. Data will be presented descriptively and analyzed to obtain an applicable model as a reference for house construction on swampy land. The model will provide an applicable depiction and will be tested against foundation construction implementation methods.

No matter where we reside, the issue of greenhouse gas emissions impacts us all. Their influence has a disastrous effect on the earth's climate, producing global warming and many other irreversible environmental impacts, even though it is occasionally invisible to the independent eye. Phase change materials (PCMs) can store and release heat when it is abundant during the day (e.g., from solar radiation), for use at night, or on chilly days when the building needs to be heated. As a consequence, buildings use less energy to heat and cool, which lowers greenhouse gas emissions. Consequently, research on thermally active medium-density fiberboard (MDF) with PCMs is presented in this work. MDF is useful for interior design and furniture manufacturing. The boards were created using pine (Pinus sylvestris L.) and spruce (Picea abies L.) fibers, urea-formaldehyde resin, and PCM powder, with a phase transition temperature of 22 oC, density of 785 kg m−3, the latent heat capacity of 160 kJ kg−1, the volumetric heat capacity of 126 MJ m−3, the specific heat capacity of 2.2 kJ kgK−1, the thermal conductivity of 0.18 W mK−1, and a maximum operating temperature of 200 °C. Five variants of MDF with PCM additive were developed: 0%, 5%, 10%, 30%, and 50%. According to the study, scores at the MOR, MOE, IB, and Screw Withdrawal Resistance (SWR) tests decreased when PCM content was added. However, the results of the thickness swelling and water absorption tests indicate that the PCM particles do not exhibit a substantial capacity to absorb water, retaining the dimensional stability of the MDF boards. The panel's thermal characteristics improved with increasing PCM concentration, according to the data. The density profiles of all the variations under consideration had a somewhat U-shaped appearance; however, the version with a 50% PCM content had a flatter form and no obvious layer compaction on the panel surface. Therefore, certain of the mechanical and physical characteristics of the manufactured panels can be enhanced by a well-chosen PCM addition.

Analysis of immediate effects of the COVID-19 pandemic on SMEs in Rwanda aims to assess and quantify the economic and financial impacts of the pandemic during the lockdown and presents options adopted by SMEs to reopen their business opera-tions. It also seeks to recommend options for sustainable and resilient economic recovery from the scars of COVID-19. This analysis used data collected from nearly 220 SMEs located across the country and applied an Exploratory Data Analysis (EDA) and multivariate linear regression models to measure the pandemic effects. The study revealed that firms downsized employment by 36.4 per cent, but data depict significant deviation within SMEs by their size. The COVID-19 pandemic has had a greater magni-tude of negative effects on sales levels among small businesses. Tax amounts were reduced amidst the crisis however, data do not show any significant variations among SMEs. Additionally, SMEs owners applied various coping mechanisms during re-opening. The study used firm-level data, providing detailed and reliable effects of the shocks on business performance. This analysis recommends establishing the medium-term financing and technical support for SMEs to ensure steady and sustainable recovery from pandemic effects as well as strengthening their resilience to any other socio-economics shocks.

Scientific studies on the impact of wood species on solid fuel production, performance, and sustainability are grossly inadequate. The knowledge of this is imperative as users of solid fuels are increasing rapidly, especially in Africa. On this note, it becomes necessary to explore measures that will improve its efficiency and sustainability as an energy source. This study investigates some properties of selected wood species used as an energy source in Nigeria and their pelleting potential. Nine (9) samples were characterized and assessed for suitability of pelleting following four wood pellet quality standards. The findings revealed Anogeissus leiocarpus as the species with the best rating score in terms of fuel properties while Vitellaria paradoxa as the lowest. However, in terms of conformity with the four wood pellets standards, Khaya senegalensis, Parkia biglobosa and Anogeissus leiocarpus having presented density, calorific value, sulfur, arsenic, cadmium, and lead within the limits of the wood pellet quality standards were considered the best wood species in terms of fuel suitability and pelleting potential. The findings therefore suggest that not all wood species are suitable as fuel. Thus, for species that do not meet the standard wood pellet requirements, alternatives such as the use of biomass blends, additives, or process adjustments can be employed to adapt the quality to the standards or by using the fuels in improved cookstoves.

The article presents the operation of the automatic pine sawn timber inspection system, which was developed at the Woodinspector company and offered commercially. The vision inspection system is used to detect various wood defects, including knots, blue stain, and mechanical damage caused by worms. Blue stain is a defect that is difficult to detect based on the color of the wood, because it can be easily confused with wood defects or dirt that do not impair its strength properties. In particular, the issues of detecting blue stain in wood, the use of artificial neural networks and improving the operation of the system in production conditions were discussed.

The Odunpazarı Modern Museum (OMM), conceptualized by Architect Kengo Kuma and inaugurated in 2019 in Eskişehir, stands as a testament to the historical significance of the timber trade in the region. The deliberate choice of wood as the primary construction material serves as a tribute to this historical narrative. The conspicuous incorporation of wooden lath materials into both the external and internal spaces signifies a conscious reference to the region's historical heritage and aligns with sustainability principles in design. The timber used to construct OMM was sourced from exhausted industrial pine forests. The creation of exhibition spaces at diverse scales involved the assembly of boxes of varying dimensions, illustrating OMM's inclination towards a formative structure characterized by “Addition and Integration.” This architectural methodology involves juxtaposing two or more primary forms to achieve a partial amalgamation. Factors such as form characteristics, dimensional distinctions, spatial arrangements, and extent of surface interactions collectively contribute to the compelling effect of this integrative approach. Within the confines of the museum, unconventional partitioning is implemented, and the strategic arrangement of masses results in multiple façades, even in the absence of overt wooden surfaces. The discernible visibility of the building's façade from an internal vantage point underscores the pivotal role played by wood in the architectural design of the OMM. The exterior impact of the wooden shell complements its interior application. The voluminous void at the heart of the structure allows for the infiltration of natural light into the internal spaces, and the wooden facade facilitates the transmission of light. The use of glass to segregate the cafeteria area from the museum entrance preserves a visual continuity between these spaces. The fundamental research inquiry in this study revolves around the user experience of wood, a material that actively influences diverse facets, including structural elements, contextual considerations, interior arrangements, and external aesthetics. To address this inquiry, a comprehensive case study and survey were conducted with the objective of elucidating the functional, sensory, perceptual, and psychological impacts of wood, the primary material in the museum's spatial configuration, on the overarching user experience.

The biofibres wide application as mortars enhancement have been so far restricted by factors related to their chemical composition and hygroscopic nature. Their hydrophilic behavior increases the water demand of mortar-mixtures and diminishes their adhesion to the matrix, while further moisture-related fibre degradation issues may arise. Additionally, the natural fibres seem to be susceptible to degradation caused during the exposure to alkaline environments conditions, such as those of cement mortars, restricting their utilization in construction industry. Therefore, the current study focusses on the potential of fibre modification through treatments that would permanently alter their structure and chemical composition in the whole mass or surface towards their performance improvement. In this study, mild hydrothermally treated wood fibres of black pine and beech species were prepared and incorporated in cement mortars to assess their performance, applying the proportion of 1.5% v/v in the mortar. The mortars workability (at fresh state), physical, hygroscopic, chemical, thermal, and mechanical characteristics at the age of 28, 90 and 365 days and weathering performance by subjecting them at different artificial ageing environments (freeze-thaw cycles or outdoor exposure) were examined. The results indicated the beneficial role of the treated fibres in the dimensional stability, flexural strength, thermal insulation properties and capillary absorption of the mortar specimens, especially during ageing process, with the black pine fibres to reveal the highest improvement. The hydrothermally treated wood fibres seem to ensure the integrity maintenance of cement mortars under all ageing conditions, proving that the specific bio-additives could provide low-cost and eco-friendly mortar enhancement pathways.

Micro and small wood-processing enterprises represent the heart of the European forest-based industries, being among the key drivers of economic growth in rural, mountainous, and poor regions. Their economic efficiency is of fundamental importance for their existence and the pro-vision of income for the local population in rural areas. Data Envelopment Analysis (DEA) is nonparametric, linear-programming-based approach, commonly used to analyse the efficiency of organizational units. This method allows estimating the economic efficiency of a certain eco-nomic system without assumptions about the functional form between resources and products. Furthermore, DEA determines the efficiency frontier and gives results of whether an enterprise, i.e., a Decision Making Unit (DMU) is efficient or not. The main objective of this study was to investigate and evaluate the economic efficiency of micro and small wood-processing enterpris-es in the EU countries and reveal the hidden inputs that facilitate efficiency generation. The eco-nomic efficiency evaluation was carried out on the basis of the official statistical data for the mi-cro and small wood-processing companies in the EU member states for the period 2015-2020 by performing a two-stage DEA analysis. The data used were standardized by value per employee. In addition to the first stage of DEA, fractional regression probit and logit models with four contextual variables were used to reveal the influence of the hidden inputs in the model. The results showed that the micro and small wood-processing enterprises can be regarded as more scale-efficient than technically-efficient entities. The only contextual variable affecting the eco-nomic efficiency was Investments per Person Employed, improving the efficiency by 2% per 1% increase of the investments.

Forest enterprise has been identified as a means of generating income among people; plays a vital role in enhancing the quality of life of forest-dependent people. Despite the opportunities timber marketing offers the people, the disparities in the income generation of the marketers in the Bodija sawn wood Market and the effect of socio-economic factors on income generation of the marketers is not well understood. This study was conducted to assess the socio-economic determinants of contributions of timber marketing to the income of timber merchants in Bodija sawn-wood Market. One hundred structured questionnaires were administered randomly in five zones of the sawn wood Market to obtain information on the socio-economic background of the sawn wood marketers and the contribution of timber trade to their incomes. The result indicated that 99.0% of the respondents were male while females constituted 1.00%. Seventy-five percent of the marketers had post-primary education and 25% had primary education. Two percent of the marketers had below 10 years of marketing experience, twenty-six percent had between 11 and 20 years, 57.00% had between 21 and 30 years, and 15.00% had more than 30years experience. Fifty-eight percent of the respondents earned between ₦10000-₦60000 (1US$ = 360.00) from timber marketing, thirty-one percent earned between ₦60001 and ₦110000, 7% earned between ₦110001 and ₦160000, while 4% earned above ₦160000 per month. Chi-square analysis of the socio-economic characteristics of the respondents and income generation at α level of 0.05 indicated that ethnicity (0.001) and years of experience (0.009) significantly influenced income while the level of education (0.101), age (0.122), and religion (0.745) had no significant influence on the incomes of marketers. Experience is an important factor in sawn wood marketing and a major determinant of the contribution of timber marketing to the income of timber marketers in Bodija sawn wood Market.

Wood-borer extermination by a dry heat clean-up is the essential method from the point of view of sustainability of historical wooden structures like trusses and ceilings in heritage-listed buildings. The wooden components are heated by a hot air of temperature about 100°C until the temperature in the centre of the wooden structures reaches 55°C to kill the wood-borers. In this article we review the method and present solution of the heat equation for structural wooden components. We also suggest an approximate formula that enables to estimate the necessary heating time for different cross sections of wooden components and can be used in technical application of the method.

The world’s population is growing at a rapid pace, thus increasing the need for shelter, which, because of increased carbon emissions, is making our planet less inhabitable. Thus, supplementary cementitious materials (SCMs) are used to reduce the embodied carbon emissions in the building sector. Wood ash, as a replacement for cement in soil treatment, seems to be a promising material. In this study, we considered the strength, stiffness, and microstructural behavior of marine clay treated with cement and wood ash as a cement replacement. Since clay is abundant in nature, it could help stabilize waste to improve the mechanical behavior of produced composites. Portland cement (7%, 10%, and 13%) was replaced with various amount of wood ash (5% and 10%) with two different dry densities (1400 and 1600 kg/m3) and three distinct curing periods (7, 28, and 60 days). Unconfined compressive strength, direct shear, porosity, pulse velocity, x-ray diffraction, and scanning electron microscopy tests were performed on selected specimens to evaluate the structural and microstructural effect of clay–wood ash–cement interaction. The results revealed that the replacement of cement with 5% of wood ash yielded superior performance. The microstructure investigation of wood ash–cement–clay blends further showed the formation of a densified matrix with stable bonds. Furthermore, the porosity and strength properties of blends developed unique relationships, which were further confirmed by other supplementary materials and soils.

Dynamic thermogravimetric (TG) analysis under nitrogen environment was used to understand the thermal decomposition process of 3D printing filaments made of wood-filled polylactic acid (PLA)/starch blend. The characteristic temperatures and apparent activation energy (AAE) of the filaments with various starch contents were calculated with well-known kinetic models by Friedman, Flynn-Wall-Ozawa, Coats-Redfern and Kissinger. With the increased starch content in the filament, the onset thermal decomposition temperatures of the filaments decreased gradually from 272.4 to 155.1°C. The thermal degradation degree became smaller, and the transitional temperature interval became larger with increased starch proportion. The AAE values of the three types of filaments with different starch ratios varied between 97 kJ/mol and 114 kJ/mol, depending on material composition and method of calculation. The improved understanding of thermal decomposition behavior of PLA-starch-wood composites can help develop more biodegradable PLA/starch-based filaments for 3D printing.

The color changes corresponding to chromophore structures in lignin caused by exposure of Eucalyptus（Eucalyptus grandis and E. urophylla）to heat were investigated. Eucalyptus wood samples were heated in saturated steam atmospheres for 10 h at 110℃, 130℃, and 150℃. The lignin was isolated before and after heat treatment. The physicochemical properties of the lignin and changes in chromophore structures during heat treatment was evaluated through wet chemical analysis, FTIR, UV-Vis, GPC, XPSand 13C-NMR. The color of the wood became darker and redder with the increase in pressure and temperature. Depolymerization and dehydration reactions occurred via demethoxylation with heat treatment in saturated steam at 110℃ or 130℃. Lignin condensed to form insoluble compounds after heat treatment in saturated steam at 150℃. G units increased and S units decreased through demethylation during heat treatment, as revealed by FTIR and 13C-NMR analysis.

The outstanding occurrences of red wood ant nests (RWA; Formica rufa-group) at two study sites in the Oberpfalz, NE Bavaria, Germany, could be confirmed by the 2023 re-inventory (a total of 5,393 nests and an increase by ≈8 %). RWA nests preferred mature and medium mature pine-dominated forests. Standing and downed dead wood do not negatively influence nests. Nest counts with woodpecker cavities and the diversity of the herb layer increased. The highly clustered nests in NW-SE direction suggests a strong interaction between nests distributions and the tectonic environment. Our developed (re-)inventory approach in combination with the comprehensive photo database is a valuable tool for a) monitoring the entire forest habitat including woodpecker cavities and dead wood in, at and around nests, and b) identifying GeoBio-Interactions. Such a comprehensive approach leads to more accurate and realistic counts of RWA nests during (re-)inventories and provides scientific evidence of the status quo of RWA occurrence. Our results disproved the unfounded and scientifically unsubstantiated blanket statement by laymen of the ASW Landesverband Bayern e.V. that RWA nest numbers in the Oberpfalz or even in the entire Bavaria are in sharp decline. We suggest seven to eight years as a suitable time interval for re-inventories.

Wood quality has been an ongoing concern for specialists, which has become increasingly important in the current context, where the demand for wood is increasing and forest fires are more frequent and violent. The article aims to evaluate the quality of wood in trees affected by fires and the negative impact of these phenomena on the speed of wood degradation, as a result of the weakening of the trees due to the action of disturbing factors. Investigations were carried out using modern techniques on the beech trees (Fagus sylvatica L.) remaining in an area affected by a litter fire in 2017. Measurements were taken were made with the Arbotom Rinntech sound tomograph, the IML F-500 Resi resistograph and the Pressler core sampler to observe the quality of the wood inside the trunk. It was found that all the trees are in various stages of decaying the tomograms being able to highlight the severity of the defects only in the case of the total destruction of the wood structure as a result of the action of xylophages fungi, whose harmful influence is more pronounced when the injuries sustained by the trees from the fire were greater. Although the trees tried to close the fire wounds through their own defense mechanisms, the destructive action of the fungi intensified with the time.After the forest fires, for quickly and clear results regarding the internal quality of the wood could be used the resistograph. For valuable trees could be used the tomograph, but the measurements have to be taken only by qualified operators.

To understand how the thinning strategies impacts on wood quality and quantity for different purposes is of interest, considering that the management of plantations is carried out with parameters that have yet to be validated for different growth conditions. This work evaluated contrasting thinning regimes applied early at two moments of the crop cycle. With an initial population of 840 trees.ha-1, two thinning with populations ranging from 700 to 400, and from 400 to 100 trees.ha-1 were applied at 1.5 and 7.3 years, respectively. Growth analyses were carried out from the ages of 1.5 to 20.8 years considering: total height, diameter at breast height, individual volume, total and commercial volume per hectare, mean annual increase and current annual increase. At final age, contrasting populations of 100, 250 and 400 trees.ha-1 were sampled to assess wood density, and mechanical properties (bending and compression on small scale clear samples). The values of individual growth and wood properties are related to a Stand Density Index to understand the effect of competition on those values. The results allow us to identify the thinning schemes that record the most significant individual and per-hectare growth (both in thinning and clear felling) and the optimal harvest time under specific growth conditions. We assessed the proportions of commercial logs for sawmill and pulp uses, providing valuable inputs for a subsequent economic analysis of thinning regimes seeking for the most convenient combination of wood products. Wood's physical and mechanical properties assessed were barely affected by contrasting levels of competition between trees, therefore the decision of the silvicultural system to implement will depend on production and economic criteria.

This study investigates the impact of specimen size on the mechanical properties of wood, specifically focusing on compression strength, elastic modulus, and Poisson's ratio. Compression tests were conducted using three different specimen sizes (20mm×20mm×30mm, 40mm×40mm×60mm, 60mm×90mm×90mm) in the longitudinal, radial, and tangential directions. Mechanical parameters, failure mechanisms, load-displacement curves, and stress-strain relationships were systematically analyzed for each size. The study also evaluated the influence of specimen size on the accuracy of finite element numerical simulations by utilizing the obtained mechanical parameters. The results reveal a significant correlation between compressive strength and specimen size, indicating a decrease in compressive strength with increasing specimen size. Conversely, elastic modulus and Poisson's ratio exhibit less sensitivity to variations in specimen size. Notably, parameters derived from small-sized specimens (20mm×20mm×30mm) exhibited substantial errors, while those obtained from medium-sized (40mm×40mm×60mm) and large-sized specimens (60mm×90mm×90mm) demonstrated greater reliability, providing precise results in finite element numerical simulations.

When wood is thermally modified, several chemical reactions take place that change the chemical and physical properties of the wood. These changes correlate with the degree of modification, which is mostly a function of temperature and duration of modification, and consequently with a mass loss during this process. There is a lack of standardized quality control to verify the degree of heat treatment of wood and thus its quality. One of the possible methods to check the degree of thermal modification of a particular type of wood is thermogravimetry (TG). It is based on the assumption that processes that did not take place during thermal modification continue when the TG experiment is carried out. In this method, calibration curves have to be established based on TG measurements of standard samples that have been thermally modified at different temperatures and whose mass loss during modification is known. The calibration curves show the mass loss during the TG measurement as a function of the mass loss during the previous thermal modification. The course of thermal decomposition during the TG measurements is influenced by many parameters, such as the mass of the sample, the heating rate, the atmosphere in which the measurement takes place, and the shape of the crucible in which the sample is placed. In this paper, the influence of these parameters on the calibration curves was investigated. We have focused on oak wood. The best parameters result in a calibration curve with the largest correlation coefficient R2 and the highest slope of the line k. On this basis, we can determine the mass loss during thermal modification of unknown samples of the same wood species under the same measurement conditions.

The objective of this work was to improve the thermal stability, flame resistance and surface properties of black poplar (Populus nigra L.) wood via different impregnation methods. The impregnation method was employed through two distinct modalities: vacuum impregnation and immersion impregnation. Here, poplar wood was impregnated with calcium oxide solutions (1%, 3% and 5%). Fourier transform infrared spectroscopic analysis revealed a shift in the typical peaks of cellulose, hemicellulose, and lignin depending on the impregnation method and solution ratio. Thermogravimetric analysis and the limiting oxygen index indicated that the samples impregnated with lime solutions exhibited higher thermal stability than the unimpregnated wood. In both impregnation methods caused a decrease water absorption and thickness swelling of the sample groups. Using a scanning electron microscope, the effect of the impregnation process on the structure of the wood was examined. In terms of surface properties, it was determined that the surface roughness value increased. On the contrary, it was observed that the contact angle value also increased. A significant difference emerged between the applied methods. In conclusion, the applied lime minerals are suitable substances to increase flame resistance and thermal stability of black poplar wood.

Although the effect of thermal modification (TM) on teak wood color is well documented, a few studies were carried out in closed system processes, as well as it remains unclear the effect of different processes on the same material. This work aimed to verify the effect of closed and open system processes of TM on the color of fast-growing teak wood. Thermally modified wood was evaluated in a closed system at 160 °C (CS160) and in an open system at 185 °C and 210 °C (OS185 and OS210). We measured the moisture content (initial and final) of wood, and the corrected mass loss (CML). The chemical analyses encompassed the contents of alpha-cellulose, hemicelluloses, lignin, and extractives (total, in acetone and dichloromethane). Wood color was measured before and after TM according to the CIEL*a*b* color space. It was possible to achieve the same color using different processes of thermal modification (CS160 and OS210). TM reduced wood lightness (L*), red-green chromaticity coordinate (a*), and yellow-blue chromaticity coordinate (b*). L* and a* had the bigger and lower variations, respectively. The color of thermally modified wood was significantly changed, even at the mildest condition tested (OS185, 0.33% CML).

The goal of this study is to find out how some properties of wood-polymer nanocomposites are affected by the processing technology, the nanomaterials, and the ratio of coupling agents. To meet this objective, the extruded and dry blended samples are made from wood flour with MAPP, ZnO nanoparticles (0, 1, 3, and 5 wt%), and polypropylene. The mechanical properties of the nanocomposites improve significantly with ZnO and MAPP loading. Due to the more homogeneous structure of nanocomposites, better mechanical results are obtained with the extrusion method. With ZnO and MAPP loading, the thermal stability of nanocomposites improves. The storage and loss modulus values indicate that the processing technology of nanocomposites could be a key factor in the resistance of the materials obtained by extrusion. The storage and loss modulus of nanocomposites manufactured by the extrusion technology are determined to be higher than those of the samples produced by the dry blending method.

This review critically examines the various ways in which the mechanical properties of wood have been understood. Despite the immense global importance of wood in construction, most understanding of its elastic and inelastic properties is based on models developed for other materials. Such models neglect wood’s cellular and fibrous nature. This review thus questions how well models that were originally developed for homogeneous and effectively continuous materials can describe wood’s mechanical properties. For example, the elastic moduli of wood have been found by many authors to depend on the size of the test specimen. Such observations are incompatible with classical elasticity theory. There is also much uncertainty about how well elastic moduli can be defined for wood. An analysis of different models for size effects of various inelastic properties of wood shows that these models only approximate the observed behaviour, and do not predict or explain the scatter in the results. A more complete understanding of wood’s mechanical properties must take account of it being in some sense intermediate between a material and a structure.

In order to improve the performance of soft plantation wood, an environmentally friendly inorganic-organic hybrid wood modifier was developed. First, using urea and melamine as crosslinking agents, the waterborne glucose silicone resin (MUG) was prepared with glucose under the catalysis of inorganic acid and metal ions. Then MUG resin was diluted to 10% and 20% mass fraction, and compounded with sodium silicate (S) of 20% and 10% mass fraction, so the inorganic-organic hybrid G10S20 and G20S10 wood modifier were obtained respectively. Then plantation poplar wood (Populus tomentosa) were impregnated and modified with them. Their physical and mechanical properties were tested and compared with those of the wood treated with S of 20% mass fraction (S20). Infrared analysis showed that amino resin characteristic structure (CO-NH-) existed in MUG resin. The resin has good permeability. Compared with S20 modified wood, the degree of shrinkage of G10S20 or G20S10 modified wood is reduced, their moisture absorption is reduced, and their dimensional stability is improved. Waterborne glucose silicone modifier can effectively improve the wood density, modulus of elasticity, modulus of rapture and compression strength. SEM analysis showed that the cell wall of G20S10 modified wood was significantly thicker than the untreated wood, and there were columnar and granular solid substances attached in some cell cavities, ducts and corners, etc. EDX showed that the number of Si elements on the cell wall was significantly increased compared with the control, indicating that the modifier effectively entered the wood cell wall. The waterborne glucose silicone resin can greatly improve the physical and mechanical properties of wood through organic-inorganic hybridization. It is a green, non-formaldehyde, eco-friendly, low cost, compound wood modifier with broad application prospects.

The paper presents a model of moisture transport in wood taking into account diffusion and the accompanying adsorption of water vapour through the skeleton. A two-parameter form of the source term was proposed, depending on the distance of the current mass concentration of bound water from the equilibrium state. The tests on cubic samples with a side of 2 cm were carried out which allowed to determine the coefficients of the proposed model on the basis of the reverse method. The tests were performed for pine, larch, oak and ash in all directions of orthotropy. Also the tests on thin samples were performed to verify the source term.

There is a restricted knowledge about the potential impact of the use of different wood species on color and anthocyanin changes during the red wine aging process. This lack of knowledge is even greater when no oak wood species are used. Thus, the aim of this study was to carry out a comparative analysis of the impact of wood chip extracts from oak, acacia and cherry species on the chromatic characteristics and anthocyanins changes by the use of model wine solutions. In this context, several methodologies were used to quantified, color and anthocyanins changes during the aging time studied. The results indicated that the contact between wood chip extracts and grape skin isolated anthocyanin extracts induced a decrease of color intensity, particularly red color, and also the anthocyanin content in the different experimental model wine solutions studied. All chromatic modifications are potentially detected by human eyes because ΔE values were much higher than 3 CIELab units. These tendencies seems to be independent of the wood species used, but more pronounced for higher contact time between wood chip extracts and anthocyanins. The obtained results may contribute to a better understanding of the chromatic changes of red wines when aged in contact with different wood chips species.

The combination of different wood modification technologies to obtain improved performance is increasingly receiving attention in research. In this study, Scots Pine (Pinus sylvestris) sapwood was impregnated with furfuryl alcohol (FFA) in pure aqueous 20, 40 and 60% solution strength without adding any catalyst. In a second step, the FFA was polymerized while simultaneously performing thermal modification in a closed system at 130, 150 or 180 °C. After leaching and ageing tests, the 9 different combinations were tested for use class 4 applications according to CEN/TS 15083-2 (2005) decay lab test. It was noted that even the minimum intensity combination of 20% FFA at 130 °C resulted in maximum durability class (DC) 1 performance. On the contrary, DC 4 was assigned to thermally modified control samples, even at the maximum intensity of thermal modification. Similarly, for FFA modifications, previous research has suggested that an uptake of 35% solution strength is required to obtain an adequate durability performance for use class 4 applications. High levels of resistance against termites were also noted by corresponding termite lab tests. Moisture studies showed the combined treatments resulted in improved stability and reduced moisture uptakes. Thus, the results obtained by this study revealed synergistic performance effects which originate from the combined thermo-chemical modification approach and which were higher than simple accumulation of the individual performance of purely thermally or chemically modified wood. Thus, the presented findings have provided positive implications for industrial applications of thermo-chemical modification techniques and offers an array of new research opportunities.

The purpose of this work is to analyze heat-treated ash wood at temperature of 185 ºC, in order to analyze its dimensional stability. For comparison, native ash/ not thermally treated wood, was be used. In order to analyze heat-treated ash wood, some main properties such as water absorption, swelling in thickness, roughness, Brinell hardness, modulus of rupture and elasticity, color change toward black with CIELab space, and many others properties were determined and processed. The results obtained after processing the experimental data have showed that heat-treated ash wood had good physical properties as absorption and swelling in thickness, and the slight increase in elasticity offers new fields of use. As a general conclusion of the work, it was established that the ash wood can be properly thermally treated, the dimensional stability characteristics being very good, and the decrease in bending resistance being almost imperceptible.

Acacia dealbata Link, named Mimosa in Portugal, is an invasive hardwood species with potential for construction use, but research is limited. The available stock of small-diameter juvenile wood (sjw) logs can help reduce this gap, but tangential cracking at log ends challenges fastener connections. This study evaluated different treatments to control and reduce end-face cracking in sjw logs during air drying, an economical and environmentally friendly procedure. Extreme two-thirds of sixteen Mimosa logs were subjected to two treatments: one with longitudinal kerfs 15 mm deep along the length (2 and 3 kerfs) and the other with a hollow in the centre up to half the length (16 mm and 30 mm diameters). Over 219 days of air drying and compared with the central part, kerfing treatments significantly reduced outer wood tangential cracking (p < 0.001), with the 3-kerf also reducing crack numbers (p < 0.05) but increasing significantly cracks near the pith (p < 0.01). The 30 mm central hollow significantly reduced central perforation cracking (p < 0.05). Results suggest that a combined treatment approach could help mitigate cracking, enhancing the suitability of wild Mimosa logs for construction use.

To achieve a micro-destructive and rapid measurement of the wood density of standing trees, this study investigated the feasibility of using the micro-drilling resistance method, formulated a mathematical model, explored the potential for a unified model across multiple tree species, and analyzed the influence of moisture content on measurement accuracy. First, 231 tree cores and drill resistance data were sampled from Pinus massoniana, Cunninghamia lanceolate, and Cryptomeria fortunei. The basic density and moisture content of each core were measured, and the average value of each resistance data record was calculated. Second, the average drill resistance, the natural logarithm of average drill resistance, and absolute moisture content were used as independent variables, while the wood basic density was used as the dependent variable. Third, the total model of the three tree species and sub-model for each tree species were established through a stepwise regression method. Finally, the accuracy of each model was compared and analyzed with that of using the average basic density of each tree species as an estimated density. The results revealed that the estimation accuracy of the sub-model for each tree species was 1.670 percentage points higher than the average value of each tree species used as the density estimation value for these tree species. Additionally, except for Cryptomeria fortunei, the natural logarithm of drill resistance significantly influenced the wood density model at a significance level of 0.05. Moreover, moisture content significantly affected the total model and sub-models of Pinus massoniana at a significance level of 0.05. The estimation accuracy of the total mathematical model was 2.125 percentage points lower than that achieved using the average basic density of each tree species to predict their density. The results indicated the feasibility of using the micro-drilling resistance method to measure the wood density of standing trees. Moreover, the relationship between wood density and drill resistance did not follow a linear pattern, and moisture content slightly influenced the drill needle resistance. Furthermore, the establishment of a mathematical model for each tree species was deemed essential. This study provides valuable guidance for measuring the wood density of standing trees through the micro-drilling resistance method.

An enormous interest in the development of efficient protocols for cellulose extraction has been demonstrated in the last years, however, they were usually based on non-sustainable chemical and thermal approaches. In this work we describe a new and more sustainable method for cellulose extraction from eucalyptus and pine tree wood waste products exclusively performed using microwave-assisted radiation. The methodology includes 3 main steps: i) alkaline treatment; ii) bleaching I, using H2O2; and iii) bleaching II, an acidic treatment. Samples obtained in each step were characterized by Fourier-transform Infrared (FTIR) spectroscopy, powder X-ray diffraction (PXRD), thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The results were compared with those of starting materials, with the commercially available microcrystalline cellulose and with an industrial paper pulp. Results confirmed that for both type of wood wastes, cellulose was retained during the extractions procedures and that the removal of hemicellulose was achieved at the last step as seen by the FTIR spectra and TGA curves. The developed protocol is innovative since it constitutes an easy and quick approach to extract cellulose, from eucalyptus and pine tree wood waste using mild chemical and thermal conditions, microwave irradiation, and environmentally friendly purification steps. This approach offers the possibility of a future scale-up study to potentially apply the develop protocol to the extraction of cellulose in an industrial scale.

In the present study, the polysaccharide-hydrolyzing secretomes of Irpex lacteus BCC104, Pycnoporus coccineus BCC310, and Schizophyllum commune BCC632 were analyzed in submerged fermentation conditions to elucidate the effect of chemically and structurally different carbon sources on the expression of cellulases and xylanase. Among polymeric substrates, crystalline cellulose appeared to be the best carbon source providing the highest endoglucanase, total cellulase, and xylanase activities. Mandarin pomace as a growth substrate for S. commune allowed to achieve comparatively high volumetric activities of all target enzymes while wheat straw induced a significant secretion of cellulase and xylanase activities of I. lacteus and P. coccineus. A synergistic effect on the secretion of cellulases and xylanases by the tested fungi was observed when crystalline cellulose was combined with mandarin pomace. In I. lacteus the cellulase and xylanase production is inducible in the presence of cellulose-rich substrates but is suppressed in the presence of an excess of easily metabolizable carbon source. These enzymes are expressed in a coordinated manner under all conditions studied. It was shown that the substitution of glucose in the inoculum medium with Avicel provides accelerated enzyme production by I. lacteus and higher cellulase and xylanase activities of the fungus. These results add new knowledge to the physiology of basidiomycetes to improve cellulase production.

Botanical recycled concrete, or concrete bonded with wood, is formed by heat pressing the mixture of concrete and wooden waste. Botanical recycled concrete is a relatively new material and the relationship between production condition and its real-world performance is not clear yet. This experimental study investigated the influence of several production condition factors on the density and bending strength of botanical recycled concrete. As a result, temperature and mass ratio of concrete powder to wood flour presented significant effects on the density of this botanical recycled concrete. The increase in production temperature resulted in a remarkable increment in density and bending strength. This is probably due to increased wood flowability and accelerated compaction and bonding formation. The fineness of wood flour had a significant effect on improving bending strength. This is attributed to a larger contact surface between the wood substance and concrete particles.

COVID-19 pandemic is a serious problem in the world today. The SARS-CoV-2 virus that causes COVID-19 has important proteins used for its infection and development, namely the protease and spike glycoprotein. The RBD (Receptor Binding Domain) of spike glycoprotein (RBD-S) can bind to the ACE2 (Angiotensin Converting Enzyme-2) receptor at the protease domain (PD) (PD-ACE2) of the host cell, thereby leading to a viral infection. This study aims to reveal the potential of compounds contained in Curcuma sp., Citrus sp., Alpinia galanga, and Caesalpinia sappan as anti SARS-CoV-2 through its binding to 3 protein receptors. The study was conducted by molecular docking using the MOE 2010 program (licensed from Faculty of Pharmacy UGM, Indonesia). The selected protein targets are RBD-S (PDB ID:6LXT), PD-ACE2 (PDB ID: 6VW1), and SARS-CoV-2 protease (PDB ID:6LU7). The affinities of bonds formed is represented as a docking score. The results show that hesperidin, one of the compounds in Citrus sp., has the lowest docking score for all three protein receptors representing the highest affinity to bind the receptors. Moreover, all of the citrus flavonoids possess good affinity to the respected receptors as well as curcumin, brazilin, and galangin, indicating that those compounds perform inhibitory potential for the viral infection and replication. In general, the results of this study indicate that Citrus sp. exhibit the best potential as an inhibitor to the development of the SARS-CoV-2, followed by galangal, sappan wood, and Curcuma sp. that can be consumed in daily life as prophylaxis of COVID-19.

A new type of laminated flooring decorated by resin impregnated paper was designed, with the advantages of high stability, low deformation, natural and beautiful surface texture, comfortable foot feeling, low formaldehyde emission, improved flame retardant, high surface hardness and high wear resistance. The structure of this engineered wood flooring is based on the ordinary laminated flooring, followed by a decorative layer of thin wood pieces, and then the transparent improved flame retardant, wear-resistant paper is added to the top. After main influencing factors analysis, the surface unevenness was seriously affect the flame-retardant performance. The wear-resistant paper pressing technology commonly affects the decorative effect of laminated flooring. The hot-pressing temperature is the most important factor affecting the adhesion of resin impregnated. The optimal hot-pressing parameters are selected as the hot-pressing pressure of 3.5 MPa, hot-pressing temperature of 180 ℃, and hot-pressing time of 40 s. The new laminated flooring was improved with high flame retardant, high wear-resistant, combined with the conventional advantages of both solid wood composite flooring and reinforced wood flooring. The new laminated flooring decorated by resin impregnated paper has broad application prospects.

:Peat substrate is made from peat from drained peatlands, which is a limited resource. A realistic estimate is that 50% of the world’s wetlands have been lost. Peat is used in horticulture, especially for the cultivation of vegetables in greenhouses. The consequences of peatland exploitation are an in-crease in the greenhouse effect and a decrease in carbon stocks. Wood fiber can be used as an al-ternative to peat. The chemical properties of the growing media interact and change continuously due to the small volume of the growing media, which is limited by the growing container. This study aims to gain new knowledge on the impact of nutrient changes in the microbial degradation of carbon compounds in wood fiber and mixtures with peat substrate on the content and uptake of nutrients required by plants. Cucumbers (Cucumis sativus L.) variety “Dirigent H” developed in the Netherlands, were cultivated in growing media of peat substrate and wood fiber: (1) peat substrate (PS); (2) wood fiber (WF); (3) wood fiber and peat substrate 50/50 v/v (WF/PS 50/50); (4) wood fiber and peat substrate 25/75 v/v (WF/PS 25/75). The rates of fertilization were the following: (1) con-ventional fertilization (CF); (2) N13; (3) N23; (4) N30. The experiment was carried out in three repli-cations. As the amount of wood fiber increased, the humidity and pH of the growing medium in-creased. Fertilization of cucumbers with different rates of nitrogen influenced the nutrient uptake. Plants grown in 50/50 and 25/75 growing media had the best Cu uptake when fertilized with N23. When the plants grown in the wood fiber media and the 50/50 media were fertilized with N13, N23, and N30, the Mn content in the growing media at the end of the growing season was significantly lower than the Mn content in the media with conventional fertilization. Thus, nitrogen improved the uptake of Mn by plants grown not only in the wood fiber but also in combinations with peat sub-strate. Growing plants in wood fiber and fertilizing them with N13 can result in optimum uptake of micronutrients. The number and mass of cucumber fruits per plant were influenced by the amount of wood fiber in the growing media and the application of nitrogen fertilizer. The highest number of fruits and mass of fruits per plant was obtained significantly higher when cucumbers were grown on WF/PS 50/50 growing media with additional N13 fertilization.

Castanopsis hystrix, a precious tree species in Southeast Asia, has the advantages of rapid growth and high-quality wood materials. However, there are problems such as long breeding cycle, time-consuming and low efficiency, which greatly restricts the industrial development of C. hystrix. To perform the genome selection (GS) for growth and wood traits and the early selection of superior progeny have great significance for the rapid breeding of new superior varieties of C. hystrix. The 226 clones in the main distribution and 479 progenies within 23 half-sib families were used as experimental materials in this study. Genotyping datasets were obtained by high-throughput re-sequencing technology, and GS studies were conducted on the growth (tree height (H), diameter at breast height (DBH)) and wood (wood density (WD), fiber length (FL), and fiber length-width ratio (LWR)) traits. The coefficient of variation (CV) of five phenotypic traits ranged from 10.1% to 22.73%, the average CV of growth traits was 19.93%, and the average CV of wood traits was 9.72%. The Pearson correlation coefficients between the five traits were almost significantly positive. Based on the Genomic Best Linear Unbiased Prediction (GBLUP) model, the broad-sense heritabilities of growth traits were higher than those of wood quality traits, and the different number of SNPs had little effect on the heritability estimation. GS prediction accuracy first increased and then reached a plateau around 3K SNPs for all five traits. The broad-sense heritability of these five traits was significantly positively correlated with their GS predictive ability (r=0.564, P

: Greenhouse plants are usually grown in containers filled with growing media. Peat is the main component of the growing media used in greenhouses. However, peat substrate is made from peat from drained peatlands, which is a limited resource. Wood fiber can be an alternative to use as a growing media for controlled-climate crops. The chemical properties of the growing media interact and change continuously due to the small volume of the growing media, which is limited by the vegetative container. Therefore, this study aims to gain new knowledge on the impact of nutrient changes in the microbial degradation of carbon compounds in wood fiber and mixtures with peat substrate on the content and uptake of nutrients required by plants. Cucumbers (Cucumis sativus L.) were cultivated in growing media of peat substrate and wood fiber: (1) peat substrate (PS); (2) wood fiber (WF); (3) wood fiber and peat substrate 50/50 v/v (WF/PS 50/50); (4) wood fiber and peat substrate 25/75 v/v (WF/PS 25/75). The rates of fertilization were the following: (1) conventional fertilization (CF); (2) N13; (3) N23; (4) N30. Fertilization of cucumbers with different rates of nitrogen influenced the nutrient uptake. Plants grown in WF/PS 50/50 and WF/PS 25/75 growing media had the best Cu uptake when fertilized with N23. When the plants grown in the wood fiber media and the 50/50 media were fertilized with N13, N23, and N30, the Mn content in the growing media at the end of the growing season was significantly lower than the Mn content in the media with conventional fertilization. Thus, nitrogen improved the uptake of Mn by plants grown not only in the wood fiber but also in combinations with peat substrate. Growing plants in wood fiber and fertilizing them with N13 can result in optimum uptake of micronutrients. The number and mass of cucumber fruits per plant were influenced by the amount of wood fiber in the growing media and the application of nitrogen fertilizer. The highest number of fruits and mass of fruits per plant was obtained significantly higher when cucumbers were grown on WF/PS 50/50 growing media with additional N13 fertilization.

Saprotrophic fungi are key in global carbon cycling, capable of decomposing lignocellulose in wood. This study, for the first time, explores the influence of oxygen (O2) and temperature on methane (CH4) production by two fungi, Laetiporus sulphureus and Pleurotus sapidus. We examined CH4 formation under varying O2 levels (0 to 98%) and temperatures (17, 27, and 40 °C) when the fungi grew on pine wood, beech wood, and grass under sterile conditions. Our findings reveal a strong dependency of fungal CH4 production on O2 mixing ratios. Methane formation was highest when O2 levels exceeded 5%, whilst no CH4 formation was observed after complete O2 consumption by the fungi. Reintroducing O2 immediately resumed fungal CH4 production. When CH4 formation was normalized to O2 consumption (CH4_norm) a different pattern between species was observed. L. sulphureus showed higher CH4_norm rates with higher O2 levels, whereas P. sapidus showed elevated rates between 0-5% O2. Temperature also significantly influenced CH4 and CH4_norm rates, with the highest production at 27 °C, and comparatively lower rates at 17 and 40 °C. These results demonstrate that O2 levels and temperature are critical in controlling fungal CH4 emissions, a consideration necessary for future CH4 source predictions.

This study concentrates on assessing the insecticidal attributes of γ-Al2O3 nanoparticles derived from remnants of Mentha pulegium, which include essential oil, ethanolic extract, and plant waste. The synthesis of γ-Al2O3 nanoparticles was executed via a direct sol-gel procedure, affirming the crystal structure through extensive physicochemical analyses such as UV-VIS, XRD, FTIR, and SEM. The evaluation of insecticidal activity in vitro was conducted against Xylosandrus crassiusculus, a pest that infests carob wood, utilizing strains from diverse forests in the Khenifra region, situated in the Moroccan Middle Atlas. The lethal doses 50 ranged from 40 mg/g to 68 mg/g, indicating moderate effectiveness compared to the commercial insecticide Permethrin. The optimization of the conditions for the efficiency of γ-Al2O3 nanoparticles was determined by experimental plans, revealing that time, humidity, and temperature were influential factors in the lethal dose 50 of these nanomaterials. Moreover, this study encompasses the establishment of correlations through Principal Component Analysis (PCA) and Ascending Hierarchical Classification (AHC) among various geographic, biological, and physical data, amalgamating geographic altitude, γ-Al2O3 nanoparticle insecticide parameters, as well as the attributes of mechanical tests conducted on carob wood affected by insects. The correlation highlights a close connection between the effectiveness of the insecticide, mountain altitude, and the mechanical parameters that were examined. Ultimately, these nanoparticles demonstrate promising potential as alternative insecticides, thus opening encouraging prospects for safeguarding against carob wood pests.

This research raises questions about the possibilities and options of using BIM methodology for wood design and construction associated with software for structure modeling along the asset's cycle life. Likewise, several academic and research initiatives are reviewed. In this sense, this paper aims to establish an appropriate link between two agendas that the architecture, engineering, and construction (AEC) industry, academia, and governments normally handle separately. By conducting several literature reviews (book, journals, and congresses) and extensive software tests (BIM software: Revit, Archicad, Tekla, and Wood plug-ins: AGACAD, Archiframe, Timber Framing 2015, WoodStud Frame, etc.), the state-of-the-art was assessed in both fields, several cases linking BIM and wood are shown in detail and discussed, various theoretical samples are modelled and shown, and the advantages and disadvantages of each technique and stage are explained. On the other hand, although wood construction has been the most common for hundreds of years, this is not the case of BIM Modeling software developments associated with this materiality. Furthermore, since the appearance of materials such as steel and reinforced concrete, all software developments have focused on these materials, leaving aside the possibility of developing applications for use in wood projects. According to previously discussed, it can be concluded that BIM for Wood has been used more frequently in academia and that both fields have several common processes and, in many cases, only a few BIM-wood tools have been used. Thus, disregarding the high potential and high level of benefits that results with the application of these methodologies for the complete building life cycle (design, construction, and operation).

Modification of Scots pine sapwood (Pinus sylvestris L.) with heterocyclic compounds, imidazole and succinimide, was investigated. Pressure-impregnation with aqueous solutions containing imidazole, imidazole + citric acid, succinimide, succinimide + citric acid, and citric acid + sorbitol (CIOL®) at 5%, 10%, and 15% solid content was followed by oven-curing at 220 °C for 1 hour. Mass changes during treatment steps, bending properties, and anti-swelling efficiency (ASE) were examined. Results indicate that solid concentrations within the range of 5% to 10% were optimal. Results seem to show there are two differing mechanisms in the modification of imidazole and succinimide, respectively. Mass loss due to the heat treatment was highest in imidazole-treated specimens, whereas it remained low and concentration-independent in succinimide-treated specimens. ASE after three cycles reached 31% for imidazole-treated specimens and improved to 38% with the addition of citric acid. For succinimide, ASE increased from 17% to 41%. Bending properties generally showed improvement, except for succinimide + citric acid and CIOL®, which displayed a reduced modulus of rupture. Chemical analyses are warranted to fully understand the reaction mechanisms of the treatments. Imidazole treatment's positive effects are suggested to stem from a thermal reaction between the chemical and wood, indicated by substantial mass loss during leaching and specimen darkening. Succinimide and citric acid might exhibit polymerization with each other and wood components, akin to the CIOL® process. Further research should delve into reaction mechanisms and the impact of imidazole and succinimide on biological durability.

To improve the measurement accuracy of wood density and study the linear correlation between the drill feed resistance and wood density, a new micro drill instrument that can can simultaneously measure the rotation resistance and feed resistance of the drill needle was designed. The test wood samples included hardwood, softwood and conifer. The absolute dry density of each wood sample was measured. The drill resistance data was tested by using self-developed micro drill instrument and Resistogaph 650-SC. 4 linear models between drill resistance and the absolute dry density of wood . The results showed that: the statistical indicators of each model of the self-made micro drill resistance in-strument were better than the corresponding indicators of Resistogaph 650-SC; the coefficient of determination of the linear regression model between the feed resistance of the self-made micro drill resistance instrument and the absolute dry density of wood was 0.946; the statistical indicators of model including rotation resistance and feed resistance, were better than those of the model only including rotation resistance. Therefor, the design proposed in the article is reasonable, and increasing the feed resistance can improve the measurement accuracy of the micro drill resistance instrument for measuring wood density.

A sustainable matrix based on eucalyptol essential oil/sawdust was developed and applied on one-sided laminated plywood. This finish aims to serve as a eucalyptol odor slow release. Eucalyptol odor release was monitored with gas chromatography coupled with a flame ionization detector (GC – FID: Limits of Detection and Quantification of 0.70 g/m3 and 2.11 g/m3, respectively, and with linearity up to 18.6 g/m3). Measurement of the eucalyptol odor released was performed during a six-month period and it was found that the release followed a first-order exponential decay with a decay rate constant of 0.0169 per day. The half-life was determined to be of 48 days. The granulometry and particle size porosity of sawdust were analyzed by Scanning Electron Microscopy. Sawdust size fraction between 112 – 200 μm showed best eucalyptol absorption capacity with 1:3 masses ratio (sawdust:eucalyptol). The time capacity of eucalyptol release depends of composite eucalyptol – sawdust quantity. Where this relation was determined: 15.0 grams of composite eucalyptol-sawdust by 0.8 mm diameter aperture gave 6 months of eucalyptol release, that was considered very positive, understanding high volatility of eucalyptol and a small quantity of composite for further products. The new product is characterized by a carbon footprint (considering the industry frontiers) of 5.94 kg CO2eq/m2 of plywood floor.

The control of air quality in museums or storages is of fundamental interest for the conservation of historic artifacts. The present work reports an example of application of RFID sensors developed in the European project SensMat and dedicated to this issue. The sensors are based on the varia-tion of property of an RFID tag coupled to a sensitive silver thin film exposed to the environment. As it will be described in the paper, such low cost sensors are interrogated by a commercial reader and provide the environmental corrosivity index and thus the presence of pollutants. The selected case study concerns the monitoring of pollution by H2S in a building dedicated to conservation and restoration of archeological and historical woods. The ability of sensors to map spatially the corrosivity within buildings is highlighted.

Oriental lacquer, a natural and renewable polymeric coating, comes from the sap produced by lacquer trees. For practical application, oriental lacquer must be refined to reduce excess water and enhance its quality. In this study, drying oils were blended with oriental lacquer during the refining process to prepare an oil-modified refined lacquer (OMRL). The type and adding amount (0, 10, and 20% by wt.) of drying oils for wood coatings utilization were evaluated. Rhus succedanea oriental lacquer is composed of 54.1% urushiols, 34.3% water, 7.2% plant gum, and 4.4% nitrogenous compounds, and drying oils, including tung oil (TO), linseed oil (LO), and dehydrated castor oil (DCO) were used as materials in this study. The results show that the drying oil acts as a diluent, which reduces the viscosity and enhances the workability and could shorten the touch-free drying time and speed up the hardened drying of the OMRL. The results also indicate that the hardness, mass retention, Tg, tensile strength, abrasion resistance, and lightfastness of OMRL films decrease as more drying oils are blended. Conversely, the bending resistance, elongation at break, impact resistance increase, and particularly, the gloss, is greatly improved through the blending of more drying oils. In conclusion, the LO-modified refined lacquer (RL) has the highest film gloss and the DCO-modified RL has the shortest drying time for coating; otherwise, the film properties are similar among the three types of drying oil.

Swamp soil presents significant challenges for infrastructure development due to its soft and deformable nature, which compromises the stability of structures. Traditional wood pillars, while cost-effective and locally available, suffer from degradation caused by moisture and biological organisms. This study investigates various methods to strengthen wood pillars, focusing on the combination of wood and concrete pillars to enhance durability and load-bearing capacity in swamp soil environments. Laboratory experiments and field tests demonstrate that encasing wood pillars in concrete or using composite materials significantly improves their mechanical strength and resistance to deformation. The results highlight the potential of these techniques to provide sustainable and economical solutions for construction in swamp areas, ensuring greater stability and longevity of the infrastructure.

To accurately identify high-quality functional wood with superior mechanical properties and enhance its durability, it is imperative to understand the relationships between the physical and mechanical attributes of diverse wood types. Presently, there exist issues related to accuracy, efficiency, and differentiation in studying these performance correlations. The Liang Kleeman (L-K) information flow theory, a causative analytical approach rooted in fundamental physics principles, offers swift computational capabilities. Furthermore, the coefficient of variation in L-K information flow quantitatively gauges the intensity of causal effects. Therefore, this article adopts a causal artificial intelligence perspective and introduces a wood performance analysis method based on L-K information flow.This study focuses on four Chinese fir varieties, including fast-growing Chinese fir (YKS), red heart Chinese fir (CSH, XXH), and iron heart Chinese fir (XXT). By computing and comparing variation coefficients of L-K information flow for various physical properties and their impact on mechanical properties, causal relationships between these properties are elucidated. These findings are then applied to predict wood mechanical properties, achieving a remarkable maximum accuracy of 90%.In the future, these findings will prove invaluable for the selection of high-quality wood and for improving the manufacturing process to prolong the service life of functionalized wood.

Sulfite and kraft pulping are two principal methods of industrial delignification of wood. In recent decades, those have been considered as possibilities to pretreat recalcitrant wood lignocellulosics for enzymatic hydrolysis of polysaccharides and subsequent fermentation of obtained sugars to valuable bioproducts. Current work compares chemistry and technological features of two different cooking processes in the preparation of polysaccharide substrates for deep sacchari-fication with P. verruculosum glycosyl hydrolases. Bleached kraft and sulfite pulps were subjected to hydrolysis with enzyme mixture of high xylanase, cellobiohydrolase and β-glucosidase activities at a dosage of 10 FPU/g of dry pulp and fiber concentration of 2.5, 5 and 10%. HPLC was used to analyze soluble sugars after hydrolysis and additional acid inversion of oligomers to monosaccharides. Kraft pulp demonstrated higher pulp conversion after 48 h (74-99%), mostly resulted from deep xylan hydrolysis. Sulfite-pulp hydrolysates, obtained in similar conditions, due to higher hexose concentration (more than 50 g/L), had higher fermentability for industrial strains producing alcohols, microbial protein or organic acids. Along with saccharification, enzymatic modification of non-hydrolysed residues occurred, which led to decreased degree of polymerization and composition changes in two industrial pulps. As a result, crystallinity of kraft pulp increased by 1.3%, which opens possibilities for obtaining new types of cellulosic products in pulp and paper industry. The high adaptability and controllability of enzymatic and fermentation processes creates prospects for the modernization of existing factories.

Recent Socio-economic changes resulted to mass abandonment of agricultural lands in Central-Eastern Europe. This leads to landscapes homogenisation, especially the disappearance of semi-open habitats of the farmland-woodland interface. The information on potentials of transforming feral, abandoned landscapes to wood-pastures is limited. We studied the ecological features and silvopastoral benefits of a landscape subjected to intensive cattle grazing after ~20 years of abandonment, i.e. the mosaic of habitats, cattle’s preference for habitats and for arboreal forages. The nutritional characteristics of arboreal forage and herbaceous forage were compared. After the initial increase in the landscape’s woodland share, cattle grazing halted further woody succession and stabilised the landscape structure, with treeless grassland occupying 49% of the landscape (most preferred by cattle with regard to the time spent), followed by treed grassland (19%), pioneering birch/alder groves (13%), riparian vegetation (12%, least preferred by cattle), and close-canopy woods (6%). The consumption intensity of arboreal forages was on about 4.5 folds higher than that of herbaceous forage. Our study proved that the grazing herd of arobust cattle breed can turn a feral, post-agricultural land into a working wood pasture, consisting of interconnected open grasslands and various facets of woodland, which seldom occur in contemporary high forests. We advocate for the transition management of abandoned farmlands towards integrated silvopastoral landscapes for sustainable provision of multiple ecosystem services that cannot be provided by segregated agriculture and forestry.

The global carbon neutrality challenge places a spotlight on forests as carbon sinks. However, greenhouse gas (GHG) balances of wood for material and energy use often reveal GHG emission savings in comparison with a non-wood reference. Is it thus better to increase wood production and use, or to conserve and expand the carbon stock in forests? GHG balances of wood products mostly ignore the dynamics of carbon storage in forests, which can be expressed as the carbon storage balance in forests (CSBF). For Germany, a CSBF of 0.25 to 1.15 t CO2/m³ wood can be assumed. When the CSBF is integrated into the GHG balance, GHG mitigation substantially deteriorates and wood products may even turn into a GHG source, e.g. in the case of energy wood. Here, building up the forest carbon sink would be the better option. We conclude that it is vital to include the CSBF in GHG balances of wood products if the wood is extracted from forests. Only then can GHG balances provide political decision-makers and stakeholders in the wood sector with a complete picture of GHG emissions.

Alkali-containing submicron particles were measured continuously during three months, including late winter and spring seasons in Gothenburg, Sweden. The overall aims were to characterize the ambient concentrations of combustion-related aerosol particles and to address the importance of local emissions and long-range transport for the atmospheric concentrations in the urban background environment. K and Na concentrations in the PM1 size range were measured by an alkali aerosol mass spectrometer (Alkali-AMS) and a cluster analysis was conducted. Local meteorological conditions and some other data sets were obtained, and back trajectory analyses and chemical transport model (CTM) simulations were included for the evaluation. The Alkali-AMS cluster analysis indicated three major clusters: 1) biomass burning origin, 2) mixture of other combustion sources, and 3) marine origin. Low temperatures and low wind speed conditions correlated with high concentrations of K-containing particles, mainly due to regional emissions from residential biomass combustion; transport of air masses from continental Europe also contribute to cluster 1. The CTM results indicate that open biomass burning in the eastern parts of Europe may have contributed substantially to high PM2.5 concentrations (and to cluster 1) during an episode in late March. According to the CTM results the mixed cluster (2) is likely to include particles emitted from different source types and no single geographical source region seems to dominate for this cluster. The back trajectory analysis and meteorological conditions indicated that the marine origin cluster was correlated with westerly winds and high wind speed; this cluster had high concentrations of Na-containing particles, as expected for sea salt particles.

To compare The effects of organic and inorganic impregnation on the properties of unmodified, phenol formaldehyde oligomer-modified (PFOMCF), and sodium silicate-modified Chinese fir wood (SSMCF) were compared using samples prepared using the respiratory impregnation method. Impregnation and reinforcement effects and water resistance of PFOMCF and SSMCF were compared and the results was showed that the weight percentage gain, density increase rate, bending strength, and compressive strength of SSMCF were clearly higher than those of PFOMCF and had a lower water absorption rate within 60 h. The impregnation and reinforcement effects and dimensional stability of SSMCF were better than those of PFOMCF. FT-IR, XRD, CONE, and TGA examinations were used to test and analyze the chemical structure, crystalline structure, flame retardancy, and heat resistance of these modified woods. The results indicated that SSMCF possessed more hydrogen bonds than PFOMCF and that Si–O–Si chemical bonding with high bond energy was formed. Meanwhile, the weakened degree of the diffraction peak of SSMCF was much less than that of PFOMCF. These results explained that the mechanical properties and water resistance of SSMCF were better than PFOMCF. Compared with PFOMCF, SSMCF had a lower heat release rate (HRR), peak-HRR, mean-HRR, total heat release, smoke production rate, and total smoke production as well as higher thermal decomposition temperature and residual rate. Inorganic sodium silicate was shown to be a better flame retardant, while SSMCF had good smoke suppression effects, thermal stability, and safety performance in the case of fire.

Intersectoral and intermunicipal cooperation are still underdeveloped spheres of public and economic development policies. Academic discussions are invariably focused on pro-competitive activities, the economic efficiency of which is not always sufficient. In this paper the authors attempt to identify factors leading to cooperation between local government authorities and economic entities, focusing on examples from the forest and wood-based sector in Poland. These processes are analysed in the framework of the New Institutional Economy, both in the theoretical and practical context.

Natural wood is generally perceived as expensive, while wood-based boards are cheap, but re-search has yet to explain definitively why these two materials receive such disparate evaluations. This study aimed to uncover the reasons behind this phenomenon by proposing an emo-tion-driven approach to material research. We collected 10 types of natural wood and artificial boards as experimental samples and tested 20 subjects' subjective evaluation of the samples and physiological indicators (electroencephalography and electrodermal activity). Through data analysis, we identified the relationships between the subjective and physiological data and the impact of material composition on these data. Specifically, we observed significant correlations between subjective and physiological data; however, no correlation was found between subjective and physiological valence. We also discovered that the components of materials significantly influence participants' subjective and physiological emotions. For example, materials with a rough texture elicited higher positive affectivity than those with a smooth texture, materials with coarse and mixed textures elicited higher positive affectivity than those with fine textures, and the brighter materials evoke more positive emotions in participants. This study revealed how material components influence participants' emotions and, more importantly, analyzed the processing techniques behind these components, providing a theoretical basis for the future development of high-value-added products made from wood-based boards.

The context of this research is given by a socio-economic situation in which new and more demanding challenges appear. Using wood, a naturally occurring, renewable, and biodegradable material, in construction is becoming more and more necessary due to the awareness of the negative impact on the environment of the construction industry and the energy crisis limitations. The purpose of this study is to analyze what do we really know about the use of wood as a building material. The search for an answer to the research question implies the use of a scientometric literature analysis, followed by an in-depth and expert analysis. The research results indicate a major preoccupation for studying engineering wood structures, like the Cross laminated Timber, the structural behaviour of the structures, the implementation of new IT discoveries in wood construction technology and a more recent approach regarding the environmental impact of wood construction, mostly the possibility of using wood waste to prolong the life of wood as a building material. The results also show a need to create new models of understanding the structural behaviour of wood that consider the fibrous and cellular nature of the material. Wood as a construction material is an extremely complex material and for a better understanding of it, there is a need to have an interdisciplinary approach in which to combine the knowledge of construction with that of forestry, ecology, biology and others.

This study investigated the anatomical characteristics and pulp quality of tapped Styrax sumatrana wood to facilitate its further utilization. The transverse surface of the tapped S. sumatrana was light or greyish brown in the sapwood and reddish brown in the heartwood. The resin canals of the tapped wood were formed along the growth rings at the boundaries between the heartwood and sapwood. Furthermore, microscopic analyses revealed an irregular outline and rounded epithelial cells at the edges of the intercellular traumatic resin canal (TC). Approximately 8–16 epithelial cells surrounded the resin canals. The fibers in the tapped S. sumatrana were generally thin-walled, whereas those near the TC were thick-walled. Moreover, S. sumatrana were diffuse-porous and exhibited intermediately distinct or indistinct growth ring boundaries. The vessels were mainly in radial multiples and clusters of 3–5. In addition, they showed a diagonal-to-radial pattern arrangement and a few tangential bands. Deposits were observed in some vessels in the tapped part but were absent in the untapped part. The fiber length of the tapped S. sumatrana wood was classified as moderate to extensive and categorized as 2nd grade pulp quality. Finally, the cell walls were classified as thin to moderate.

Air pollution and the increasing production of greenhouse gases has prompted greater use of renewable energy sources; the EU has set the use of green energy at 32 percent by 2030. With this in mind, in the last 10 years the demand for pellets in Italy has more than doubled making Italy the second largest consumer in Europe. The quality of the pellets burned in stoves is crucial to indoor and outdoor pollution. Among other parameters, moisture and ash are used to classify pellets according to EN ISO 17225:2014. This work involved the analysis of the organic and inorganic fraction of both some finished products on the Italian market and some raw materials (e.g., wood chips) sampled according to the technical standard EN 14778:2011. The analytical results showed the presence of some substances potentially harmful to human health such as formaldehyde, acetone, toluene and styrene for the organic fraction and nickel, lead and vanadium for the inorganic fraction. The chemometric approach showed that it is the inorganic fraction which is most responsible for the diversification of the samples under study. The detection of some substances may be a warning bell about the impact of such materials both for the environment and for the human health.

Our knowledge of physics and chemistry is relatively well defined. Results from that knowledge are predictable as, largely, are those of their technical offspring such as electrical, chemical, me-chanical and civil engineering. By contrast biology is relatively unconstrained and unpredictable. A factor common to all areas is the trade-off, which provides a means of defining and quantifying a problem and, ideally, its solution. In order to understand the anatomy of the trade-off and how to handle it, its development (as the dialectic) is tracked from Hegel and Marx to its implementa-tion as dialectical materialism in Russian philosophy and TRIZ, the Theory of Invention. With the ready availability of mathematical techniques, such as multi-objective analysis and the Pareto set, the trade-off is well-adapted to bridging the gaps between the quantified and the unquantifiable, allowing modelling and the transfer of concepts by analogy. It is thus an ideal tool for biomimet-ics. An intracranial endoscope can be derived with little change from the egg-laying tube of a wood wasp. More complex transfers become available as the technique is developed. Most im-portant, as more trade-offs are analyzed, their results are stored to be used again in the solution of problems. There is no other system in biomimetics which can do this.

Emissions from wood burning for heating in secondary homes or cabins is an important aspect for the development of high-resolution emission inventories in specific areas. Norway is used as case study as the national wood consumption for heating in cabins is around 20% of the total. Our study shows first a method to estimate emissions from cabins based on traffic data to derive cabin occupancy, which combined with heating need allows for the spatial and temporal distribution of emissions. The combination of residential (RWC) and cabin wood combustion (CWC) emissions shows large spatial and temporal differences, and a temporally “cabin population” can in areas be orders of magnitude larger than the registered population. While RWC emissions have been steadily reduced, CWC have kept relatively constant or even increased, which results on an increase in the cabin share to total heating emissions up to 25-35%. When comparing with regional emissions inventories, our study shows that the gradient between rural and urban areas is not well represented in regional emissions inventories, which resembles a population-based distribution and does not allocate emissions in cabin municipalities. At last, our study shows that CWC emissions may become an increasing environmental concern as higher densification trends in mountain areas are observed.

Batch combustion in wood log stoves is a promising application for latent heat storage (LHS), due to the transient heat production with high peak effects. The current study aimed at designing a compact, passive and durable LHS system storing a substantial part of the heat release during batch combustion and effectively releasing the stored heat to the room for 6 to 10 hours after the last batch. The LHS system consists of a coaxial cylinder located at the top of the wood stove, replacing part of the regular stovepipe. Internal metallic fins were applied as heat transfer enhancement to homogenize the temperature distribution inside the PCM. The effect of radial fin lengths was numerically investigated through a parametric study using five different fin lengths within the PCM. Using 35-mm fins in the 70-mm PCM layer yielded the best trade-off for the application. This configuration enabled achieving a slow but close to complete melting of the PCM within a realistic combustion duration, while avoiding overheating the PCM above its degradation temperature. Thereafter, the discharge allowed releasing the stored latent heat for 6 hours. The exhaust gas inlet temperature proved to have a strong influence on the PCM thermal performance.

A composite is a material formed from the combination of two or more constituent materials through a non-homogeneous mixture. This research aims to determine the effect of volume fraction and fiber orientation angle of the hybrid polyester-ulin wood powder (Eusideroxylon zwageri)-wire mesh composite on bending strength. The bending test was conducted using ASTM D-790 standard with a three-point bending test method. The composite was made using the hand lay-up method with various compositions of particles and polyester. The results showed that the composition with less ulin wood powder and finer mesh size with a 45° wire mesh angle orientation had the highest bending strength and high deformation capability. The addition of wire mesh did not significantly increase the bending strength but could reduce the effect of decreased deformation capability.

This paper presents an innovative approach to dimensionality reduction and feature extraction in high-dimensional datasets, with a specific application focus on wood surface defect detection. The proposed framework integrates sparse modeling techniques, particularly Lasso and proximal gradient methods, into a comprehensive pipeline for efficient and interpretable feature selection. Leveraging pre-trained models such as VGG19 and incorporating anomaly detection methods like Isolation Forest and Local Outlier Factor, our methodology addresses the challenge of extracting meaningful features from complex datasets. Evaluation metrics such as accuracy and F1 score, alongside visualizations, are employed to assess the performance of the sparse modeling techniques. Through this work, we aim to advance the understanding and application of sparse modeling in machine learning, particularly in the context of wood surface defect detection.

Natural dyes offer a bio-based opportunity to support attractive coloration to textile fabrics made from natural fibers like cotton, wool, hemp and many other materials. They can be part of a strategy to realize fully bio-based textile materials and clothing. Following this statement, the actual study investigates the use of wood extracts for dyeing of cotton fabrics. Actually extract powders of Logwood (Haematoxylon campechianum L.), Brazilwood (Caesalpinia spp.), and Quebracho wood (Schinopsis lorentzii) are used. The dyeing process is modified using different mordants based on iron and aluminum salts. These mordants are applied in pre-, meta- or post-mordant procedures. Color and fastness properties of prepared textile samples are determined by spectroscopic measurements, color measurements, washing procedures and Xenotest for measuring the light fastness. Finally, a broad range of different colorations can be realized by different combinations of wood extracts and mordanting procedures. A good wash fastness is reached for some color shades. For reaching good wash fastness, pre- and meta-mordanting procedures are more advantageous compared to post-mordanting. However, the light fastness of realized samples is only moderate to low. In conclusion, it can be stated that dyes from wood extracts are excellent materials to dye natural fibers if they are combined with the right mordanting agent in pre- or meta-mordanting procedures. The actual study is therefore a good proof-of-concept for the realization of fully bio-based colored textile materials.

Main pathogens affecting carob (Ceratonia siliqua) tree in the Mediterranean basin are described in this overview. The most widespread diseases periodically occurring on carob orchards are powdery mildew (Pseudoidium ceratoniae) and cercospora leaf spot (Pseudocercospora ceratoniae). The causal agents of so-called “black leaf spots” (e.g. Pestaliotiopsis, Phyllosticta and Septoria spp.) are responsible for similar symptoms to above mentioned foliar diseases but are reported on carob orchards with a negligible frequency. Likewise, canker and branch diebacks caused by fungal species belonging to Botryosphaeriaceae are almost never recorded. Among wood diseases that may compromise old or previously damaged carob specimens, “brown cubical heart rot” caused by Laetiporus sulphureus is the most widespread and recurrent issue; this pathogen is also well-known for edible fruit bodies that are also appreciated for pharmaceutical and industrial purposes. On the other hand, “white decays” caused by Fomes and Ganoderma species are less common and reported for the first time in this review. Like-gall protuberances on twigs at uncertain aetiology or tumours on branches associated to Rhyzobium radiobacter are described although these symptoms are seldom detected as it happens also for necrotic leaf spots caused by Pseudomonas syringae pv. ciccaronei. A list of worldwide pathogens not yet recorded but at high-risk potential of introduction in Italian carob producing area is also provided. Finally, some concerns are addressed to new phytopathogenic fungi vectored by invasive Xylosandrus compactus ambrosia beetle. Comprehensively, all described pathogens could potentially in near future become limiting factors for carob production, because they could be favoured by high-density orchards, increasing global network of trade exchanges and high frequency through which extreme events of climate changes globally occur. Thus, symptoms and signs, causal agents, epidemiology and whenever applicable recommendations for disease prevention and management are provided in this review.

Uganda possesses natural rainforests that serve enormous environmental ecosystems and biodiversity services. Moreover, the country is known for its various tropical rainforest hardwoods, birds, and animal species. Over the years, the trend in the natural forest land has declined at an alarming rate; hence need to investigate the possible drivers. The loss of such biodiversity and ecosystems risks desertification and extreme climatic condition. As the world moves towards Zero Deforestation 2030, understanding the determinants of deforestation and forest degradation is paramount. Therefore, the main objective of this study was to understand the impact and relationships between net forest conversion, energy emission, agriculture, and forest production of Roundwood. We used data from FAO for the period 2004-2016. Using the ADF and KPSS test, we checked for the unit root presence in the variables. Also, the study used two different regression models: multiple linear regression and dynamic linear model. To analyze the determinants of deforestation, we used net forest conversion in Uganda. There was 94 % variation in the dependent variable (Net Forest conversion). The outcome of the dynamic linear regression showed that agriculture and energy emission positively impact net forest conversion. Based on our findings, this study recommended the modernization of agriculture by the government of Uganda to stop cutting down the forests on a big scale. Also, the study suggested that the government strictly legislate Roundwood and wood fuels/charcoal and firewood to reduce huge dependency on forests toward Zero-Deforestation by 2030. If well-structured and implemented, government policies could solve the unnecessary over dependency on the rainforest, the heart of the region's climatic conditions.

The effectiveness of forest resources depends on the comprehensiveness and rationality of their consumption and processing into finished products. This article discusses a problem of utilising solid fir wood greenery residues generated during the industrial production of essential oils. Bioconversion is considered to be the most promising utilization method. The objective of this research was to study the chemical composition of bioconversion products of fir wood greenery-based substrates. The РР-3.2 strain of Pleurotus pulmonarius (Fr.) Quél was used as a biodestructor. In the process of bioconversion, the contents of polysaccharides and lignin substances is reduced to 38 and 28 % respectively. Up to 20 % of protein accumulates in bioconversion products of fir wood greenery. The amount of nucleic acids is not more than 1.5 g per 1 kg, the contents of heavy metals, such as mercury, cadmium, arsenic, lead, do not exceed maximum permissible concentration standards. The substrate weight loss reaches 15 %. When fallen leaves and post-extraction poplar bud residues are added to the substrate, the substrate-destroying activity of fungi rises, as well as the protein content increases by 3 %. The digestibility of products as a result of bioconversion increases 1.6–2.8 times depending on the substrate composition. The obtained data enable to recommend post-fermented substrates based on fir wood greenery and balsam poplar biomass for use as a protein feed additive.

Forestry and the wood-based sector, including the wood industry, which is an important element of economic systems and a source of budget revenues for many countries in the world, found itself in the first quarter of 2020 in a situation of a serious threat of a prolonged crisis as a consequence of the pandemic. In this perspective, it is necessary to review existing sector strategies and look for new solutions to ensure first survival, then functioning and finally development of entities forming the wood market. In the scientific research, which is the subject of this work, an attempt was made to multi-criteria analysis of the selection of the optimal anti-crisis strategy for actors from forestry and the wood-based sector in the face of a pandemic. Preparatory studies were conducted on the example of Poland, where both forestry and the wood industry belong to the dominant sectors of the economy, conducting them at the turn of March and April 2020. The research was referred to the primary wood raw material market in Poland, which is the main link in the value chain, created first by the dominant owner: Państwowe Gospodarstwo Leśne "Lasy Państwowe" - the “State Forests” National Forest Holding (SFNFH), and then forest service entrepreneurs, to entities representing the wood industry. The work uses a concept modified for the purposes of the author's research scenario, based on the method of multi-criteria hierarchical analysis AHP (Analytic Hierarchy Process). The best possible decision was to be searched that would allow the selection of the optimal anti-crisis strategy for enterprises - actors of the sector concerned. Based on the collected results and their expert discussion, recommendations for sectoral policy for forestry and the wood-based sector were then formulated. The proposed solutions are located against the background of a dispute between the concept of institutional intervention and a model taking into account the effects of market factors. The work is both cognitive (optimization and adaptation of the research method) and practical up-to-date. An accurate development strategy for forestry and the wood-based sector is urgently needed and necessary to implement as quickly as possible.

Ranaviruses have been associated with rising numbers of mass die-offs in amphibian populations globally. With life-stages occupying different environments and presenting distinct physiologies, amphibian of different ages are likely to play an important role in pathogen persistence. To assess the potential role of post-metamorphic amphibians as a Ranavirus reservoir, we performed a bath-exposure study on wood frogs using environmentally relevant doses (~10³ and ~10⁴ PFU/mL) of wild-type (WT) and knockout Frog virus 3 (FV3), deficient for the vIF-2α immune-evasion gene, the effects of which have never been addressed in post-metamorphic anurans. We observed 42% infection prevalence and low mortality (10%) across the virus challenges, with half of the mortalities attributable to ranavirosis. Prevalence and viral loads followed a dose-dependent pattern. Notably, when exposed to the vIF-2α knockout (DvIF-2α) FV3, individuals exhibited significantly decreased growth and increased lethargy in comparison to WT FV3 treatments. Although 85% of individuals in the virus treatments exhibited stereotypic signs of ranavirosis throughout the experiment, at termination (40 days post exposure) most individuals were clear of signs of infection. Overall, this study provides evidence that even a single short time exposure to environmentally relevant doses of Ranavirus may cause sublethal infections in post-metamorphic amphibians, thus indicating their possible role as a reservoir for this pathogen.