The physical and mechanical properties of rocks will change significantly after being subjected to high temperatures, which poses safety hazards to underground projects such as coal underground gasification. In order to investigate the effect of temperature on the macroscopic and microscopic properties of rocks, this paper has taken sandstone as the research object and conducted uniaxial compression tests on sandstone specimens at different temperatures (20-1000 ℃) and different heating rates (5-30 ℃/min) at 1200 ℃. At the same time, the acoustic emission (AE) test system was used to observe the acoustic emission characteristics of the rock damage process, and the microstructural changes after high temperature were analyzed with the help of a scanning electron microscope (SEM). The test results show that the effect of temperature on sandstone is mainly divided into three stages: Ⅰ (20-500 ℃) stage is the strengthening zone, the evaporation of water and the contraction of primary fissures, sandstone densification is enhanced. Specifically, the compressive strength and elastic modulus increase, the macroscopic damage mode is dominated by shear damage, and the fracture micro-morphology is mainly brittle fracture. Stage II (500-600°C) is the transition zone, 500°C is the threshold temperature for compressive strength and modulus of elasticity, and the damage mode changes from shear to cleavage damage, and the sandstone undergoes brittle-ductile transition in this temperature interval. Stage III is the physicochemical deterioration stage. The changes in physical and chemical properties make the sandstone compressive strength and modulus of elasticity continue to decline, the macroscopic damage mode is mainly dominated by cleavage damage, and the fracture microscopic morphology is more toughness fracture. The effect of different heating rates on the mechanical properties of sandstone was further studied, and it was found that the mechanical properties of the rock were more deteriorated under higher heating rates.

To clarify the relationships among critical temperature, critical magnetic field, and critical current density, this paper describes many-body interactions of quantum magnetic fluxes (i.e., vortices) and calculates pinning-related critical current density. All calculations are analytically derived, without numerical or fitting methods. Afteralculating a magnetic flux quantum mass, we theoretically obtain the critical temperature in a many-body interaction scenario (which can be handled by our established method). We also derive the critical magnetic field and inherent critical current density at each critical temperature. Finally, we determine the pinning-related critical current density with self-fields. The relationships between the critical magnetic field and critical temperature, inherent critical current density and critical temperature, and pinning critical current density and temperature were consistent with experimental observations. From the critical current density and critical magnetic field, we clarified the magnetic field transition. It appears that a magnetic flux quantum collapses when the lattice of magnetic flux quanta melts. Our results, combined with our previously published papers, provide a comprehensive understanding of the transition points in high-T_c cuprates.

A pilot study on laser 3D printing of inorganic free-form micro-optics is experimentally validated. Ultrafast laser nanolithography is employed for structuring hybrid organic-inorganic material SZ2080TM followed by high-temperature calcination post-processing. The combination allows production of 3D architectures and the heat-treatment results in converting the material to inorganic substance. The produced miniature optical elements are characterized and their optical performance demonstrated. Finally, the concept is validated for manufacturing compound optical components such as stacked lenses. This is opening for new directions and applications of laser made microoptics under harsh conditions such as high intensity radiation, temperature, acidic environment, pressure variations, which include open space, astrophotonics, and remote sensing.

Considering the significance of thermodynamic cycles in the global energy system, it is necessary to develop new general classes of thermodynamic cycles to relieve current energy and environmental problems. Inspired by the relationship between power cycles and refrigeration cycles, we realize that general classes of thermodynamic cycles should occur in pairs with opposite functions. Here we reverse class 1 heating cycles to obtain another new general class of thermodynamic cycles named class 2 heating cycles (HC-2s). HC-2s have two basic forms, and each contains six thermodynamic processes. HC-2s present the simplest and most general approach to utilizing the temperature difference between a medium-temperature heat source and a low-temperature heat sink to achieve efficient high-temperature heating. HC-2s fill the gaps that have existed since the origin of thermal science, and they will play significant roles in the global sustainable energy system.

This paper discusses domestic problem of waiting hot water for the shower use till it reaches satisfactory temperature, which result a lot of wastage in fresh water. The outcome from research survey shows that there is no satisfactory solution till now as all solutions were either expensive or with no effective results. Local small inline electric heater equipped with fuzzy logic controller is proposed in this paper to be installed just before the showerhead to measure the water temperature and flow before the showerhead, as control input-variables, and decide the operating voltage of the heater, as control output-variable (MISO). MATLAB Simulink is used to model the proposed system. Different test cases are simulated to prove the performance and the safe operation of the system. Techno-economic study is carried out to determine the “Direct Benefits” and “Indirect Benefits” that can be achieved if such system is implemented in wide range. Azerbaijan data is taken as an example to calculate the economic benefits. The results show important benefits not only for economy but also for climate and the reduction of CO₂ gas emission. Different economic indices are provided to be an easy reference for decision makers and project managers.

innate and adaptive immune responses lead to wound healing by regulating a complex series of events promoting cellular cross-talk. An inflammatory response is presented with its characteristic clinical symptoms: heat, pain, redness, and swelling. Some smart thermo-responsive polymers like chitosan can be used to create biocompatible and biodegradable scaffolds with 3D architectures similar to human structures, allowing their efficient and safe use as tissue engineering and drug delivery systems in chronic wounds. Locally heated tumors above polymer lower critical solution temperature can induce its conversion into a hydrophobic form, enhancing drug release until the thermal stimulus is gone, where a lower release is due to the swelling of the material. This paper integrates the relevant reported contributions of bioengineered scaffolds for thermo-responsive drug delivery in wound healing. Therefore, we present a comprehensive review that aims to demonstrate the capacity of these systems to provide spatially and temporally controlled release strategies for one or more drugs used in wound healing. In this sense, the novel manufacturing techniques of 3D-printing and electrospinning are explored for the tuning of their physicochemical properties to adjust therapies according to the patient’s convenience, as well as reduce drug toxicity and side effects.

Land Surface Temperature (LST) estimation has been studied for several purposes, while the optimal method of estimating the LST has not been criticized yet. This research explores the optimum method in Land Surface Temperature (LST) estimation using LANDSAT-8 imagery data. Four different LST retrieval approaches, the Radiative Transfer Equation-based method (RTE), the Improved Mono-Window method (IMW), the Generalized Single-Channel method (GSC), and the Split-Window algorithm (SW), were calculated to present the LSTs over Buriram Town Municipality, Thailand. The calculated LSTs from these four methods were compared with the ground-based temperature data, taken on the same date and time of the employed LANDSAT-8 images. For this reason, the optimum method of the LST calculation was justified by considering the lowest normalized root means square error (NRMSE) values. As a result, the SW algorithm presents an optimum method in LST estimation. Regarding the SW, this algorithm requires not only the atmospheric profiles during satellite acquisition but also the retrieval of several coefficients. Besides, the LST retrieval method based on the SW algorithm is sensitive to water vapor content and coefficients. Although the SW algorithm is an optimum method explored in this study, it is emphasized that the adjustable values of coefficient response to the atmospheric state may be recommended. With these conditions, the SW algorithm can generate the land-surface temperature over the mixed land-use and land cover on the LANDSAT-8 images.

The classical approach to non-linear regression in physics, is to take a mathematical model describing the functional dependence of the dependent variable from a set of independent variables, and then, using non-linear fitting algorithms, extract the parameters used in the modeling. Particularly challenging are real systems, characterised by several additional influencing factors related to specific components, like electronics or optical parts. In such cases, to make the model reproduce the data, empirically determined terms are built-in the models to compensate for the impossibility of modeling things that are, by construction, impossible to model. A new approach to solve this issue is to use neural networks, particularly feed-forward architectures with a sufficient number of hidden layers and an appropriate number of output neurons, each responsible for predicting the desired variables. Unfortunately, feed-forward neural networks (FFNNs) usually perform less efficiently when applied to multi-dimensional regression problems, that is when they are required to predict simultaneously multiple variables that depend from the input dataset in fundamentally different ways. To address this problem, we propose multi-task learning (MTL) architectures. These are characterized by multiple branches of task-specific layers, which have as input the output of a common set of layers. To demonstrate the power of this approach for multi-dimensional regression, the method is applied to luminescence sensing. Here the MTL architecture allows predicting multiple parameters, the oxygen concentration and the temperature, from a single set of measurements.

We report the results of an analysis of the functional capabilities of the KTP crystal and its isomorphs for nonlinear-optical frequency conversion of all types of interaction in the transparency range of the crystal. The possibility of implementing angle-, wavelength- (frequency-) and temperature-noncritical phase matching is shown.

Recent algorithmic-based research in the stock market has predominantly focused on ultra-high-frequency trading and index estimation. We developed an improved algorithm to address the need for a low-frequency, real-world trading model to build on the existing high hit-ratio and low maximum drawdown. We utilized established price indicators, Stochastic and Williams %R, and introduced a volume factor to increase the model's safety to enhance the model's performance. This improved algorithm demonstrated superior returns while maintaining high hit-ratio and low maximum drawdown. Specifically, we leveraged the existing algorithm to trade using 2X and 3X signals, incorporating volume data, the 52-week average, standard deviation, and other factors. The data set comprised SPY ETF price and volume from 2010 to 2023, covering over 13 years. Our enhanced algorithmic trading model outperformed both the benchmark and previous results, achieving a hit rate of over 90%, a maximum drawdown of less than 1%, an average of 1.5 trades per year, a total return of +519.3%, and an annualized return (AnnR) of +15.1%. The analysis demonstrates that the model's simplicity, ease of application, and comprehensibility can assist investors in making informed investment decisions albeit the past performance does not guarantee future returns.

Background/Objectives: Dental implants have become a cornerstone of restorative dentistry, providing a long-lasting method for tooth replacement. The level of osseointegration has a big impact on the biomechanical stability at the bone-implant contact (BIC), which determines how long these implants will work. However, the exact consequences of changing osseointegration levels on different implant designs, especially in bones with variable densities, are not well known. Three short dental implants were tested in this study: BioMet 3iT3, Straumann® Standard Plus Short Regular Neck (SPS-RN), and Straumann® Standard Plus Short-Wide Neck (SPS-WN). 3D finite element analysis (FEA) was used to look at how well they worked biomechanically. This paper tests the implants at four stages of osseointegration: 25%, 50%, 75%, and 100% in both high-density (Bone Type III) and low-density (Bone Type IV) cancellous bone. It also created and examined realistic CAD models under static occlusal loading conditions to assess stress distribution and major strains at the bone-implant contact.; Results: The study discovered that as osteointegration increases, von Mises stress and principal strains go down significantly for all implant types. The SPS-WN implant had the lowest strain values, especially for bone with low density. These reductions demonstrate increased mechanical stability as the bone-implant inter-face becomes more capable of dispersing mechanical stresses, minimizing the potential for localized deformation and bone resorption.; Conclusions: The results highlight the importance of achieving optimum osseointegration to reduce mechanical stress and increase the lifespan of dental implants. The SPS-WN type implant performed better in biomechanical tests than the others, especially when bone conditions were not ideal. This makes it a great choice for clinical applications that need long-term implant success.

Oxytocin is recommended as the first-line choice for labor induction in term pregnant women with premature rupture of membranes (PROM); however, it can occasionally lead to failed induction and delivery complications. The primary objective of this study was to compare delivery information and outcomes following the administration of oxytocin infusion or oral low-dose misoprostol solution for labor induction in term PROM women with an unfavorable cervical condition. Methods: A prospective nested case-control study was conducted at a tertiary general hospital in China from March 2020 to February 2024, comparing oxytocin infusion and oral administration of 25ug misoprostol every 2 hours for labor induction in term PROM women with a Bishop score <6. A total of 449 mothers were included, with 282 in the oxytocin group and 167 in the misoprostol group. Results: The rates of vaginal delivery and failed induction were similar between the two groups. The duration of total labor time was shorter in the misoprostol group. There were no significant differences observed regarding the incidence of uterine hyperstimulation, fetal stress, or suspected intrauterine infection between the two groups; however, there was a markedly higher incidence of postpartum hemorrhage (PPH) and severe PPH but lower postpartum urinary retention (PPUR) observed in the oxytocin group. Logistic regression analysis revealed that misoprostol administration demonstrated a negative relationship (aOR: 0.46; 95% CI: 0.21-0 .95) with failed labor induction outcomes, while IVF-ET showed a positive association (aOR:3.12; 95% CI:1.49-6.43). Furthermore, there was a negative correlation identified between misoprostol administration and occurrence of PPH (aOR: 0.49; 95% CI: 0.27-0.85). Conclusions: Oral low-dose misoprostol has demonstrated both safe and superior efficacy to oxytocin infusion for labor induction and may potentially reduce the incidence of failed induction and associated with a decreased risk of PPH were observed in the misoprostol group in term PROM pregnant women with unfavorable cervical condition.

A fundamental aspect in the evolution of Time-to-Digital Converters (TDCs) implemented within Field-Programmable Gate Arrays (FPGAs), given the increasing demand for detection channels, is the optimization of resource utilization. This study reviews the principal methodologies employed for implementing low-resource TDCs in FPGAs. It outlines the foundational architectures and interpolation techniques utilized to bolster TDC performances without unduly burdening resource consumption. Low-resource Tapped Delay Line, Vernier Ring Oscillator, and Multi-Phase Shift Counter TDCs, including the use of SerDes, are reviewed. Additionally, novel low-resource architectures are scrutinized, including Counter Gray Oscillator TDCs and interpolation expansions using Voltage-Temperature-Consumption stable IODELAYS. Furthermore, the advantages and limitations of each approach are critically assessed, with particular emphasis on resolution, precision, non-linearities, and, especially, resource utilization. A comprehensive summary table encapsulating existing works on low-resource TDCs is provided, offering a comprehensive overview of the advancements in the field.

The unprecedented progress in Artificial Intelligence (AI), particularly in deep learning algorithms with ubiquitous internet connected smart devices, has created a high demand for AI computing on the edge devices. This review studied commercially available edge processors, and the processors that are still in industrial research stages. We categorized state-of-the-art edge processors based on the underlying architecture, such as dataflow, neuromorphic, and Processing in-Memory (PIM) architecture. The processors are analyzed based on their performance, chip area, energy efficiency, and application domains. The supported programming frameworks, model compression, data precision, and the CMOS fabrication process technology are discussed. Currently, most of the commercial edge processors utilize dataflow architectures. However, emerging non-von Neumann computing architectures have attracted the industry in recent years. Neuromorphic processors are highly efficient for performing computation with fewer synaptic operations, and several neuromorphic processors offer online training for secured and personalized AI applications. This review found that the PIM processors show significant energy efficiency and consume less power compared to dataflow and neuromorphic processors. The future direction of the industry would be to implement state-of-the-art deep learning algorithms in emerging non-Von Neumann computing paradigms for low power computing on the edge devices.

Mortality in children accounts for 15% of all AIDS-related deaths globally, with a higher burden among Cameroonian children (25%), likely due to poor virological response. We sought to evaluate viral suppression (VS) and its determinants in a nationally representative paediatric and young adult population receiving antiretroviral therapy (ART). A cross-sectional and multicentric study was conducted among Cameroonian children (

Great Himalayan range with regions namely, Jammu & Kashmir, Ladakh and high altitude parts of north eastern states inherently experience high solar exposure, cold, arid climate and significantly challenging geography. With a scarcity of affordable public housing projects in these regions a grid enabled low energy residential prototype is proposed having the capability to operate on nearly zero consumption of heating and cooling energy with the application of indigenous and contemporary energy efficient passive design techniques. Preliminary study, development of design and reading of simulation results were applied for the performance and benefit analysis of the low energy building prototype. Analysis of the climatic zone further classified and narrowed the design criterion by confirming upon beneficial architectural components proven to be energy efficient. These architectural components include, optimization of direct solar gain and orientation of building envelope, modified trombe wall system, traditional sunrooms, solar chimney with openable vents, efficient spatial planning and compliance of relevant parameters such as window-wall-ratio (WWR). The proposed low energy housing for the economically weaker section is estimated to save nearly 50% of active fuel based household heating energy. Site has been planned in such a way that about 100% of required electricity can be generated from on site renewable energy for the proposed infrastructure, it is proven more beneficial if additional electricity is generated to offset the power supply and result in lower or subsidized electricity bills. Design is compliant to different codes relevant to energy conservation and low-income housing with an embodied carbon of about 1.2 kgCO2/m2 per dwelling unit giving ‘A’ grade in cradle to gate impacts. The findings and performance of this prototype can serve as a guideline for energy efficient design in low income group housing situated in severe cold and arid regions of India such as Ladakh (U.T.).

Background: The objectives were to evaluate: the safety and immunogenicity of nonavalent human papillomavirus (nHPV) vaccine in adult Spanish women living with HIV (WLHIV); the prevalence of anal and cervical dysplasia and nHPV vaccine genotypes in anus and cervix; and risk factors for high-risk HPV (HR-HPV) infection in anal mucosa. Methods In this single-center, open-arm, non-randomized clinical trial, nHPV vaccine was administered at 0, 2, and 6 months to WLHIV enrolled between February 2020 and November 2023, measuring vaccine antibody titers pre-vaccination and at 2, 6, and 7 months after the first dose. Cervical and anal cytology and HPV PCR genotyping studies were performed. Women with abnormal cytology and/or anal or cervical HPV infection at baseline underwent high-resolution anoscopy and/or colposcopy. Results: 122 participants were included with mean age of 49.6 years: 52.5% smoked; 10.7% had anal-genital condylomatosis; 38.5% infection by HR-HPV in anus and 25.4% in cervix, most frequently HPV-16; 19.1% had AIN1 and 3.1% CIN1 and CIN2. Vaccine administration did not modify viral-immunological status (CD4 [809±226.8 cells/uL vs. 792.35 ±349.95; p=0.357]) or plasma HIV load (3.38±4.41 vs. 1.62±2.55 cop/uL [log]; p=0.125). Anti-HPV antibodies ([IQR: 0-0] vs. 7.63 nm [IQR: 3.46-19.7]; p=0.0001) and seroconversion rate (8.2% vs. 96.7% [p=0.0001]) were increased at 7 versus 0 months. There were no severe vaccine-related adverse reactions; injection-site pain was reported by around half of participants. HR-HPV infection in anus was solely associated with concomitant cervix infection (HR 5.027; 95% CI: 1.009-25.042). Conclusions: nHPV vaccine in adult WLHIV is immunogenic and safe.

A regional modern river-sand geochemical mapping study in the majority of the Timor-Leste territory, including the research area, has not been previously reported. This study demonstrated the potential of modern river sand geochemical mapping as an effective method for lithological mapping, particularly in areas that face challenges in conducting efficient geological fieldwork and have limited geological information. A total of 53 modern river sand samples were collected and analyzed. Before examining the samples using wavelength-dispersive X-ray fluorescence for ten major elements, the loss-on-ignition method was employed. In the Clerec drainage basin, SiO2, CaO, and K2O showed positive correlations, and CaO was positively correlated with MnO. Similarly, in the Sahe River catchment, a positive relationship was observed between CaO, MnO, and TiO2. These findings suggested the presence of quartz, manganese, secondary K-bearing minerals, and secondary Ti-bearing minerals in carbonate rocks that have undergone silicification and other alteration processes. The principal component analysis results corroborated the SiO2/Al2O3 and K2O/Na2O ratios and the ICV findings. PC1 was related to the variations in Ca-poor and Ca-rich rocks; PC2 indicated notable inputs from SiO2-rich and SiO2-poor rocks; and PC3 revealed the possibility of contributions from secondary mineral assemblages related to silicification and low-grade metamorphic processes.

This study determines the equivalent stress intensity factor (SIF) model that best fits the experimental behavior of low-carbon steel under mixed mode (I and II). The study assessed Tanaka, Richard, and Pook's equivalent SIF models. The theoretical values used for comparison correspond to experimental results in a modified C(T) geometry by machining a hole ahead of the crack tip subjected to fatigue loads with a load ratio of R = 0.1. The comparison involved the SIF for six experimental points and the values computed through the numerical simulation. The Paris, Klesnil, and modified Forman-Newman crack growth models were used with each equivalent SIF to analyze the prediction in the estimated number of cycles. The Klesnil model showed the closest prediction since the error between the calculated and experimentally recorded number of cycles is the lowest. However, the material behavior reflects a reduced crack propagation rate attributed to plasticity in the crack tip. Results suggest that Asaro equivalent SIF conservatively estimates the element lifespan with increasing errors from 2.3% at the start of growth to 27 % at the end of the calculation.

Severe COVID-19 alters the biochemical and morphological characteristics of blood cells in a wide variety of ways. To date, however, the vast majority of research has been devoted to the study of leukocytes, while erythrocyte morphological changes have received significantly less attention. The purpose of this research was to identify erythrocyte types that were unique to COVID-19, compare the number of different poikilocyte types, and measure erythrocyte sizes to provide data on size dispersion. Red blood cells obtained from 6 control donors (800-2200 cells for each donor) and 5 COVID-19 patients (800-1900 cells for each patient) were examined using low voltage scanning electron microscopy. We did not discover any forms of poikilocytes that would be unique to COVID-19. Among COVID-19 patients, we observed an increase in the number of acanthocytes (p=0.01) and a decrease in the number of spherocytes (p=0.03). In addition, our research demonstrates that COVID-19 causes an increase in the median (p=0.004) and interquartile range (p=0.009) when assessing erythrocyte size.

A fluorescent probe, N'-((3-methyl-5-oxo-1-phenyl-4, 5-dihydro-1H-pyrazol-4-yl) methylene)-2-oxo-2H-chromene-3-carbohydrazide (MPMC), was synthesized and characterized. Characterizations of the synthetic MPMC were conducted by proton nuclear magnetic resonance (1HNMR) spectroscopy and carbon-13 nuclear magnetic resonance spectroscopy (13C NMR). The fluorescence emission behaviors of probe MPMC towards diverse metal ions were detected and the probe exhibited high sensitivity and selectivity towards Cu2+ over other metal ions via quenching of its fluorescence. Furthermore, the existence of other metal actions made no difference on the fluorescence intensity of the MPMC-Cu2+ system apparently, that is, MPMC displayed a good anti-interference ability. Job’s plot of MPMC and copper ions indicated the detection limit was 15.16 nM (R2=0.9612) for the assayed actions, with a stoichiometric ratio of 1:1 for MPMC and Cu2+. Additionally, the color of MPMC probe solution changed from nearly colorless to yellow in the presence of Cu2+ in visible light, which the color change could be observed by the naked eye. Similarly, the color resolved bright yellow into blue in ultraviolet light. Also reusability studies indicated that MPMC probe was reusable. The pH effect of probe MPMC to Cu2+ had a broad range of pH detection 4.0 to 11.0. The response time of MPMC probe for determining Cu2+ was within 1 min. The recognition of Cu2+ by MPMC performed on pre-treated paper under sunlight and UV light both had a distinct colour change. Thus, the solid-state method for detecting Cu2+ with the naked-eye, was both economical and convenient.

This article presents a study conducted within a wind tunnel to enhance understanding of the excitation mechanism of stay cable vibration under arid conditions. Numerous wind tunnel tests were meticulously analyzed. Initially, the vibration of the stay cable was measured under steady flow conditions at a flow angle of 45 degrees and an inclination of 25 degrees, while varying wind velocities were applied. Additionally, an investigation into the flow field surrounding the stay cable was conducted in both vertical and horizontal directions. By utilizing two hot wire anemometers in the cable wake, an extensive database of flow field measurements was obtained. The experimental results revealed that the vibration characteristics of the stay cable under the arid conditions considered in this study aligned with findings reported in existing literature. Notably, a deeper comprehension of the excitation mechanism of a stay cable in a dry state was attained. This mechanism is closely associated with the inhibition of Karman vortices and the development of low-frequency vortices. At low wind speeds, Karman vortices predominated, resulting in small-amplitude vibrations. However, as the wind speed increased, the influence of Karman vortices diminished progressively, while the low-frequency vortices grew stronger. These low-frequency vortices exhibited high energy and a significant correlation with shedding along the stay cable, thereby inducing cable vibration in a dry environment.

To accomplish IMO's emissions reduction targets, the Chinese government has established emission control areas and implemented strict sulfur limitation policies. Faced with the downturn in the shipping industry and the challenge of insufficient supply of compliant fuel, Hong Kong and Shenzhen in China have implemented different low-sulfur fuel subsidy policies. Therefore, it is particularly important to study the air pollution control mechanism considering low sulfur fuel subsidy policy. Firstly, the non-cooperative game models considering low-sulfur fuel subsidies are constructed. Secondly, the mechanisms of various factors affecting port pricing, throughput and profit are analyzed. Then, a case study is conducted by using AIS data of container ships in Shanghai Port and Ningbo Zhoushan Port. The study reveals that whether the container service price of the leader port increases or decreases, the follower port always take corresponding follow-up measures. In both sequential and simultaneous game, the profit difference of the leader port is positively related to the subsidy ratio of the port’s own and negatively related to the coefficient of the competitor's subsidy. In conclusion, the low-sulfur fuel subsidy policy has a significant positive impact on the step-by-step implementation of more stringent pollution reduction policies in port waters.

This paper presents a proposal for a non-isolated bidirectional converter (NIBC) controlled by a deep neural network (DNN) to enable vehicle-to-vehicle (V2V) and vehicle-to-grid (V2G) charging, which contributes to the development of more efficient and sustainable transportation and energy systems. The DNN controller manages power flow in both directions, making it possible to charge electric vehicles (EVs) and discharge power from EVs to the grid with improved efficiency and performance compared to traditional control methods. The non-isolated topology used in this proposal offers several benefits, including reduced cost, smaller size, and higher efficiency. To train the DNN controller, a large dataset of simulations was used, and the results were validated with a hardware setup. The real-time performance of the DNN controller was compared to a proportional-integral (PI) based controller through simulated results. The findings of the study show that the DNN controller outperforms traditional PI controllers.

We explored the outcomes of germline BRCA1/2 pathogenic/likely pathogenic variants (PVs/LPVs) in the endocrine-sensitive disease treated with first line standard of care cyclin-dependent kinase 4/6 (CDK4/6) inhibitors. Three studies retrospectively showed a reduction in overall survival (OS) and progression free survival (PFS) in gBRCA1/2m patients compared to both germinal BRCA1/2 wild type (gBRCA1/2wt) and to the untested population. Regarding the efficacy of PI3K inhibitors, there are no subgroup or biomarker analyses in which germinal BRCA status was explored. However, the biological interactions between the PIK3CA/AKT/mTOR pathway and BRCA1/2 at a molecular level could help us to understand the activity of these drugs when used to treat BC in BRCA1/2 PVs/LPVs carriers. The efficacy of trastuzumab deruxtecan (T-DXd), an antibody-drug conjugate (ADC) targeting HER2 for HER2-low and HER2-positive (HER2+) BC, has been increasingly described. Unfortunately, data on T-DXd in HER2+ or HER2-low metastatic BC harboring germinal BRCA1/2 PVs/LPVs is lacking. Including germinal BRCA1/2 status in the subgroup analysis of the registration trials of this ADC would be of great interest, especially in the phase III trial DESTINY-breast04. This trial enrolled patients with HER2-negative (HER2-) and both HR+ and HR- metastatic disease, which can now be categorized as HER2-low. The HER2-low subgroup includes tumors that were previously classified as triple negative, so it is highly likely that some women were germline BRCA1/2 PVs/LPVs carriers and this data was not reported. Germline BRCA1/2 status will be available for a higher number of individuals with BC in the near future and data on the prognostic and predictive role of these PVs/LPVs is needed in order to choose the best treatment options.

The Direction-of-Arrival (DoA) estimation methods are highly versatile and find extensive applications in satellite communication. The DoA methods are employed across a range of orbits, from Low Earth Orbits (LEO) to Geostationary Earth Orbits (GEO). They serve multiple applications, including altitude determination, geolocation and estimation accuracy, target localization, and relative and collaborative positioning. This paper presents a novel approach for modeling the DoA angle using a closed-form expression, incorporating the boresight angle and satellite and Earth station position data. The method uses the geographic coordinate system in the satellite communication system, precisely the latitude and longitude of the Earth station and altitude parameters of the satellite stations, to calculate the Earth station’s elevation angle and accurately model the DoA angle. Furthermore, this paper performs a comprehensive comparative analysis of various DoA methods to gain deeper insights into the performance of DoA estimation in multi-antenna systems operating under spatially correlated channels. Accordingly, this paper evaluates DoA estimation performance using root-mean-square-error (RMSE) statistics for uplink and downlink conditions through extensive Monte Carlo simulations. The simulation’s effectiveness is validated against the Cramer-Rao Bound (CRB) performance metric for the Additive white Gaussian noise (AWGN) case. (i.e., thermal noise). The simulation results demonstrate improved RMSE performance in satellite systems by incorporating spatial correlation into the system model.

Hydro generator sets serve as the peak and frequency regulation of the power system,and play a very important role in maintaining system stability and improving power quality.Based on the internal characteristics model of a specific type of hydro generator,this paper constructs a hydroelectric coupling model for hydropower units,studies the influence of the regulation system of hydropower units on low-frequency oscillations under different load conditions,and adopts variable speed reaching law and fuzzy sliding mode control strategy to improve the regulation quality of the system and ensure the stable operation of the units.Results of simulation and water turbine set under different load conditions show that varible speed reaching law can effectively improve the power-angle oscillation behavior of the hydropower set and suppress the occurrence of low-frequency oscillations of the system when the system is subject to power disturbance,which provide a new theoretical basis and solution for the vibration analysis and control optimization of hydraulic turbine units.

An extended classification of active RC- and RLC- filters with Sallen-Key architectures, including those created in the last three years, is proposed. This makes it possible to formulate new design directions for an extended family of active RC- and RLC- Sallen-Key filters (PF, LPF, HPF, RF) for the tasks of high-speed and ultra-fast analog-to-digital signal conversion.

Ensuring a protection scheme in DC distribution is more difficult to achieve against pole-to-ground fault than in AC distribution system because of the absence of zero crossing points and low line impedance. To complement the major obstacle of limiting the fault current, several compositions have been proposed related to mechanical switching and solid-state switching. Among them, solid-state circuit breakers(SSCBs) are considered a possible solution to limit fast fault current. However, they may cause problems in circuit complexity, reliability and cost-related troubles due to the use of multiple power semiconductor devices and additional circuit configuration to commutate current. This paper proposes the SSCB with a coupled inductor(SSCB-CI) which has symmetrical configuration. The circuit is comprised of passive components like commutation capacitors, a CI and damping resistors. Thus, proposed SSCB-CI offers the advantages of simple circuit configuration and fewer utilized power semiconductor devices than another typical SSCBs in LVDC microgrid. For analysis, six operation states are described for the voltage across main switches and fault current. The effectiveness of the SSCB-CI against a short-circuit fault is proved via simulation and experimental results in a lab-scale prototype.

A high proportion of dogs and cats are fearful during veterinary visits, which in some cases may escalate into aggression. Here, we discuss factors that contribute to negative emotions in a veterinary setting and how these can be addressed. The set-up of the waiting area (e.g. spatial dividers; elevated places for cat carriers), tailoring the examination and the treatment to the individual, considerate handling (minimal restraint when possible, avoiding leaning over or cornering animals) and offering high-value food or toys throughout the visit can promote security and, ideally, positive associations. Desensitisation and counterconditioning are highly recommended both to prevent and address existing negative emotions. Some negative experiences such as short-term pain from injections can be minimised by using tactile and cognitive distractions. Preemptive analgesia is recommended for known painful procedures. Recommendations for handling fearful animals to minimise aggressive responses are discussed. However, anxiolytics or sedation should be used whenever there is a risk of traumatising an animal or for safety reasons. Stress-reducing measures can decrease stress and fear in patients and consequently their owners – thus strengthening the relationship with the clients as well as increasing the professional satisfaction of veterinary staff.

Background: Low-level physical activity (PA) among Chronic Low Back Pain (cLBP) is associated with various biopsychosocial factors. This research aimed to study the predictors of PA behavior among cLBP patients. Methods: In the present study 300 eligible patients with cLBP who referred to comprehensive health service centers in the Shahid Beheshti University of Medical Sciences (SBUMS) in Tehran, Iran were random selected.To diagnose the predictors of PA behavior, all the Theory of Reasoned Action (TRA) constructs were examined as risk factors to see if they influence on the probability of PA behavior occurrence and were interpreted through odds ratio (OR). SPSS version 19 was used to analyze the data. Results: Totally 280 cLBP patients with mean age of 57.07 ±13.09 years old participated in the study. This study showed that motivation to comply significant predictor the cLBP patients for subjective norm OR (%95CI): 2.095(0.116-2.792), p-value<0.001), intention was significant predictor for perform the PA behavior OR (%95CI): 1.431(0.138-1.538), p-value <0.001), behavior beliefs could predictor for attitude OR (%95CI): 1.276(0.106-1.355), p-value= 0.002). attitude, normative beliefs, subjective norm ,and evaluation outcome behavior could predictors the cLBP patients for intention to perform the PA behavior OR (%95CI): 1.188(0.032-1.312), p-value<0.001)., OR (%95CI): 1.158(0.076-2.208), p-value=0.003) ., OR (%95CI): 1.104(0.076-1.128), p-value<0.001) ., OR (%95CI): 0.814(0.301-1.440), p-value=0.007). Conclusions: This study showed that the cLBP patients who were normative beliefs and evaluation regarding PA behavior could effect on the intention to engage in greater PA than those via other constructs (attitude and subjective norm). This study showed that the cLBP patients who were normative beliefs and evaluation regarding PA behavior could effect on the intention to engage in greater PA than those via other constructs (attitude and subjective norm). This study showed that the cLBP patients who were normative beliefs and evaluation regarding PA behavior could effect on the intention to engage in greater PA than those via other constructs (attitude and subjective norm).

Green infrastructure systems are often overdesigned. This may be a byproduct of static sizing (e.g., accounting for a design storm’s runoff volume but not exfiltration rates) or may be deliberate (e.g., buffering against performance loss through time). Regardless, overdesign may compromise plants’ access to water in systems where soil pits are embedded in infiltration beds. It could raise the storm size required for water to reach soil pits, reducing water availability between storms, which could ultimately induce plant physiological stress. This study investigated the hydrological dynamics and water relations of a tree trench system suspected to have been overbuilt and identified factors contributing to, compounding, and mitigating the risk of plant stress. Results provided strong evidence that the abovementioned processes played out. Water in the infiltration bed reached soil pits only once in three years, with that event occurring during a hydrant release. Moreover, minimal water was retained in the soil pit during the event due to the hydraulic properties of the soil media. Through a growing season, one of the two tree types frequently experienced water stress, while the other did so only rarely. These contrasting responses can likely be attributed to roots either being largely confined to the soil pits or reaching a deeper water source. Implications of these results for green infrastructure design are considered.

The solution of structural problems with nonlinear material behaviour in a model order reduction framework is investigated in this paper. In such a framework, greedy algorithms or adaptive strategies are interesting as they adjust the reduced order basis (ROB) to the problem of interest. However, these greedy strategies may lead to an excessive increase in the size of the reduced basis, i.e. the solution is no more represented in its optimal low-dimensional expansion. Here, an optimised strategy is proposed to maintain, at each step of the greedy algorithm, the lowest dimension of the PGD basis using a randomised SVD algorithm. Comparing to conventional approaches such as Gram-Schmidt orthonormalisation or deterministic SVD, it is shown to be very efficient both in terms of numerical cost and optimality of the reduced basis. Examples with different mesh densities are investigated to demonstrate the numerical efficiency of the presented method.

As a result of the cancer immunotherapy revolution hundreds of clinical trials of the newly approved immunotherapies are now under way to improve responses. Not unexpectedly, the 2018 Nobel Prize in Physiology or Medicine was awarded to James P. Allison and Tasuku Honjo for their development of cancer therapy by blockade of co-inhibitory signals. While success stories of terminal cancer patients achieving complete remissions are accumulating, not enough research has been done into the risks of the new therapies. Since the use of immunotherapy is becoming more common, and is expected to develop into first- and second-line treatments, immunotoxicity and autoimmunity are emerging as the nemesis of immunotherapy. Immune-related adverse events (IrAEs) could affect any tissue, their incidence may reach up to 90% of patients and toxicity is dose-dependent. While the combination of two immune checkpoint inhibitors (ICIs) increased efficacy, the incidence of severe adverse events was also increased. Apparently, ICIs cannot be restricted to the targeted anti-tumor T cell population. The long lasting objective of cancer regression can only be achieved by paying a price: tolerance to healthy self tissues is compromised. In the face of an ipilimumab induced pan-lymphocytic activation, a therapeutic paradigm shift is required. The task is not desperately trying to put the genie back in the bottle by immune suppressive treatments, but instead harnessing the autoimmune forces by an off label low-dose combined anti-CTLA-4 and anti-PD1 antibody blockade, which is supplemented with conventional interleukin-2 stimulation and hyperthermia. The proof-of-principle of the low-dose-combination therapy was demonstrated in a heavily pre-treated triple negative breast cancer (TNBC) patient with far advanced pulmonary metastases and severe shortness of breath, who had exhausted all conventional treatment. Her pulmonary metastases went into complete remission with transient WHO I-II diarrhea and skin rash. She lived for 27 months after starting the low-dose-combination therapy. She had recurrence as a sternal mass and pleural metastases up to 3 cm. Since the low-dose-combination protocol consists only of approved drugs and treatments, this exceptional response should instigate further research efforts.

We have successfully measured amyloid beta (Aβ) (1-40) protein added in human serum by a NiCr strain gauge cantilever biosensor immobilized with liposomes incorporating cholesterol. Importantly, we investigated the effect of incorporation of cholesterol in the liposome in order to suppress the interaction between the liposome and many different proteins included in human serum. It was revealed that incorporating cholesterol suppresses the interaction between the proteins other than Aβ in human serum and the liposome. Finally, we detected Aβ(1-40) in human serum with typical chronological behaviors due to Aβ aggregation and fibrillization. Furthermore, as a digital low-pass filtering procedure could reduce external noises, the cantilever sensor immobilized with liposome incorporating cholesterol can detect low-concentrated Aβ in human serum.

This study presents a reproducible and scalable method for synthesizing silica nanoparticles (SNPs) with controlled sizes below 200 nm, achieved by systematically varying three key reaction parameters: ammonium hydroxide concentration, water concentration, and temperature. SNPs with high monodispersity and controlled dimensions were produced by optimizing these factors. The results indicated a direct correlation between ammonium hydroxide concentration and particle size, while higher temperatures resulted in smaller particles with increased polydispersity. Water concentration also influenced particle size, with a quadratic relationship observed. This method provides a robust approach for tailoring SNP sizes, with significant implications for biomedical applications, particularly in drug delivery and diagnostics. Using eco-friendly solvents such as ethanol further enhances the sustainability and cost-effectiveness of the process.

Transient conjugate heat transfer measurements under varying temperature and velocity inlet boundary conditions at incompressible flow conditions were performed for flat plate and ribbed channel geometries. Therefrom local adiabatic wall temperatures and heat transfer coefficients are determined. Those data are analyzed using typical heat transfer correlations, e.g. Nu=CRe^mPr^n determining the local distribution of C and m. It is shown that they are closely linked. A relationship lnC=A−mB is observed with A and B as modeling parameters. They could be related to parameters in log law or power law representations for turbulent boundary layer flows. The parameter m is shown to have a close link to local pressure gradients and therewith near wall streamlines as well as friction factor distributions. A normalization of the C parameter allows to derive a Reynolds analogy factor and therefrom local wall shear stresses.

Sepsis still remains one of the most difficult conditions to diagnose as it presents unspecific clinical signs and symptoms, which makes early detection crucial. Our study aimed to enhance the accuracy of sepsis diagnosis by integrating multimodal monitoring technologies with traditional diagnostic methods. The research involved 121 newborns, comprising 39 cases of late-onset sepsis, 35 cases of early-onset sepsis, and 47 control subjects. Biosignals including pulse oximetry (PO), near-infrared spectroscopy (NIRS), and skin temperature (ST) were continuously monitored and an algorithm was developed using Python for identifying early signs of sepsis. The model demonstrated the ability to detect sepsis 6 to 48 hours in advance with an accuracy rate of 87.67% ± 7.42%. Sensitivity and specificity were recorded at 76% and 90%, respectively, with NIRS and ST having the most significant impact on predictive accuracy. Despite the promising results, limitations such as sample size, data variability, and potential biases were noted. The findings highlight the critical role of non-invasive biosensing methods in conjunction with traditional biomarkers and cultures, offering a robust framework for early sepsis detection and improved neonatal care. Further studies are recommended to validate these results across diverse clinical settings.

The Reactive Spark Plasma Sintering (R-SPS) method is compared in this work with the two-steps SHS-SPS route, based on combination of the Self-propagating High-temperature Synthesis (SHS) with the SPS process, for the fabrication of dense (Hf0.2Mo0.2Ti0.2Ta0.2Nb0.2)B2-SiC and (Hf0.2Mo0.2Ti0.2Ta0.2Zr0.2)B2-SiC ceramics. A multiphasic and inhomogeneous product, containing various borides, is obtained at 2000°C/20min by R-SPS, from transition metals, B4C and Si. In contrast, if the same precursors are first reacted by SHS, and then processed by SPS under the optimized condition of 1800°C/20min, the desired ceramics are successfully attained. Both High-Entropy-Boride/SiC products display densities > 97%, uniform microstructures and contained only small amounts of residual oxides (<2.4 wt.%). The presence of SiC makes the sintering temperature milder, i.e. 150°C below to that needed by the corresponding additive-free system. Fracture toughness is also markedly improved, particularly when considering the Nb-containing system processed at 1800°C/20min, whereas KIC progressively decreases (from 7.35 to 5.36 MPa m1/2) as the SPS conditions become more severe. SiC addition is found to inhibit the volatilization of metal oxides like MoO3 formed during oxidation experiments, thus avoiding mass loss in the ceramics. The benefits above also likely take advantage of the fact that the two composite constituents are synthesized in parallel, according to the SHS-SPS approach, rather than being produced separately and combined subsequently, so that strong interfaces between them are formed.

Cities exemplify the evolving world with changing demographics and climates. Urban green spaces play a crucial role in improving the quality of life of people through their potential to mitigate temperatures. Therefore, comprehending their impact is of para-mount interest. Given the challenges in obtaining temperature data from urban locations, this study develops Artificial Neural Networks (ANNs) to predict daily and hourly temperatures in Valladolid, Spain, with a particular focus on urban allotment gardens and a forested urban park. ANNs were built and evaluated from various combinations of inputs (X), hidden neurons (Y) and outputs (Z) under the practical rule of "making net-works simple, to obtain better results". The best performing model was 6-Y-1 ANN archi-tecture with an impressive result of Root Mean Square Error (RMSE) = 0.42°C in the urban garden called Valle de Arán. However, other five ANN architectures were also tested (7-Y-5; 6-Y-5; 7-Y-1; 3-Y-Z and 2-Y-1). ANNs dedicated to urban temperature analysis hold immense potential for urban planning and research, aiding in under-standing the urban climate, forecasting future temperatures, identifying temperature mitigation strategies and even for managing urban crops

In this report, we establish a straightforward method for estimating the equilibrium constant for the CK reaction over wide but physiologically and experimentally relevant ranges of pH, Mg2+ and temperature. Our empirical formula for CK Keq” is based on experimental measurements. It can be used to estimate [ADP] when [ADP] is below the resolution of experimental measurements, a typical situation because [ADP] is on the order of micromolar concentrations in living cells, and may be much lower in many in vitro experiments. Accurate prediction of [ADP] is essential for in vivo studies of cellular energetics and metabolism, and for in vitro studies of ATP-dependent enzyme function under near-physiological conditions. With [ADP], we could estimate ΔGATP. Application to actomyosin force generation in muscle provides support for the hypothesis that, when [Pi] varies but not when pH is altered, maximum Ca2+-activated isometric force depends on ΔGATP in both living and permeabilized muscle preparations. Further analysis of the pH studies introduces a novel hypothesis for the role of submicromolar ADP in force generation.

The present study sought to determine the effect of incorporating a Chitosan-TiO2 nano-composite on the color stability of pigmented Room Temperature Vulcanization (RTV) maxillofacial silicone subjected to a variety of accelerated aging conditions. The experimental setup consisted of one hundred groups of five disk-shaped specimens (22mm diameter, 2mm thick) each, created using RTV silicon elastomer type A-2186, with the total sample distributed into four groups based on the pigments combined with the silicon—specifically, brilliant red, blue, and yellow dry intrinsic pigments (at 0.2% concentration by weight) and a fourth group that remained non-pigmented. Each of these primary groups was further subdivided into five categories corresponding to the silicon variants treated with different nanoparticles—2% TiO2, 3% Chitosan, a hybrid nano-combination of 1% TiO2/Chitosan, 1% synthesized Chitosan-TiO2 Nanocomposite, and a control group devoid of nanoparticle additions. The synthesized Chitosan-TiO2 Nanocomposite was effectively prepared using the core-shell method. The color stability of each silicon category, irrespective of whether pigmented or non-pigmented was evaluated by calculating the color difference (ΔE) pre- and post-subjection to five distinct accelerated aging conditions: 30 hours in an antibacterial cleaning solution, six months in sebum, six months in sweat, UV-accelerated aging for 720 hours, and outdoor weathering for six months. Color measurements were taken using a Colorimeter within the CIELAB color system. Statistical analyses, including one-way ANOVA at a significance level of p < 0.05, were employed to discern significant differences among the various accelerated aging conditions across the five silicon categories. Further comparisons were made using Dennett's T3 multiple comparison test, Tukey HSD multiple comparisons, and a t-test, with SPSS for Windows version 27.0 as the software platform. Results indicated that all silicon types, whether pigmented or not, exhibited varying degrees of color change under different aging conditions. Red-colored samples, across all silicon categories, demonstrated significant color alterations after 720 hours of UV-accelerated aging, with the most pronounced change in the 3% Chitosan samples and the least in the 2% TiO2 samples. Six months of outdoor weathering led to a marked increase in ΔE values across all categories. The blue-pigmented silicon samples treated with 2% TiO2 showed the highest color modification, while the yellow-pigmented silicon and non-pigmented silicon also underwent significant color shifts, particularly in the control and Chitosan-TiO2 categories, respectively. The study underscores the pervasive influence of outdoor weathering on color stability across all silicon categories. It also demonstrates that while nanoparticle incorporation offers some resilience against accelerated aging, it fails to provide adequate protection against the specific effects of UV radiation encountered during outdoor weathering.

The intercomparison among different atmospheric monitoring systems is key for instrument calibration and validation. Common cases involve satellites, radiosonde, radio occultation (e.g. GNSS-RO) and atmospheric model outputs (e.g. ERA5 reanalysis). Since instruments and/or measures are not perfectly collocated, the miss-collocation uncertainty must be considered in the related intercomparison uncertainty budgets.

Plums are primarily marketed for fresh consumption, canning, freezing, jam and jelly. Unfortunately, plum consumption has remained steady or declined. Consumers complain about a lack of flavor quality but are willing to pay for higher quality. Thus, lack of flavor and cold storage disorders are the main barriers to consumption. Plum cultivars are susceptible to gel breakdown, flesh browning and ‘off flavors’. Consumer acceptance and postharvest life are highly dependent on genotype, quality attributes, harvest date and proper postharvest handling. A consumer quality index (CQI) based on soluble solids concentration (SSC) and minimum firmness is proposed to maximize flavor and postharvest life. In most cases, late harvest increases quality attributes. Our work and industry experience demonstrated that using critical bruising thresholds (CBT) based on minimum firmness measured at harvest acts as a reliable predictor of how late to harvest safely for maximum visual and sensory quality. Plums are well adapted to late harvest because of their low susceptibility to bruising damage, but proper postharvest temperature management and marketing within the potential market life are necessary to maintain flavor and avoid the onset of storage disorders. Thus, to maximize flavor and postharvest life, a CQI based on SSC and minimum firmness measured at consumption is proposed. This article provides guidance on using this CQI, combined with proper postharvest handling techniques such as correct harvest date determination and temperature management, to maintain quality and increase consumption.

Background. Chest CT is widely regarded as a dependable imaging technique for detecting pneumonia in COVID-19 patients, but there is growing interest in microwave radiometry (MWR) of the lungs as a possible substitute for diagnosing lung involvement. Aim. The aim of the study is to examine the utility of the MWR approach as a screening tool for diagnosing pneumonia with complications in patients with COVID-19. Methods. Our study involved two groups of participants. The control group consisted of 50 individuals (24 male and 26 female) between the ages of 20 to 70 years who underwent clinical evaluations and had no known medical conditions. The main group included 142 participants (67 men and 75 women) between the ages of 20 to 87 years who were diagnosed with COVID-19 complicated by pneumonia and were admitted to the emergency department between June 2020 to June 2021. Skin and lung temperatures were measured at 14 points, including 2 additional reference points, using a previously established method. Lung temperature data were obtained with the MWR2020 (RTM-01-RES) (MMWR LTD, Edinburgh, UK), a CE Class I device. All participants underwent clinical evaluations, laboratory tests, chest CT scans, MWR of the lungs, and reverse transcriptase polymerase chain reaction (RT-PCR) testing for SARS-CoV-2. Results. The MWR exhibits a high predictive capacity as demonstrated by its sensitivity of 98.6% and specificity of 84.0%. Conclusions. MWR of the lungs can be a valuable substitute for chest CT in diagnosing pneumonia in patients with COVID-19, especially in situations where chest CT is unavailable or impractical.

This study investigates the cultural dimension in sustainable lighting design to create inclusive environments. India being one of the most culturally and ethnically diverse nations in the world, with a population of almost 18% of the world population, requires attention to include cultural dimension in the design of sustainable environments. With the changing lifestyle and growth in organized retailing, the Indian retail market needs an upgrade to create inclusive environments for shared retail experiences. Lighting is among most influencing atmospheric attribute to create simulating environment for a holistic shopping experience. Preference of lighting conditions vary across the store profiles and users’ cultural background. Very little research has been carried out to understand the lighting preferences of retail customers in India. This study investigated the effects of correlated colour temperature and illuminance levels on spatial impressions and user preferences in mid-range store profile. This study involved ninety-three participants in evaluating high definition visualisations of the sixteen lighting conditions. The observations from this study emphasizes the necessity of similar studies across various states of India to identify the lighting preferences for other functional spaces and cultural backgrounds within the country. The findings may contribute towards providing recommended guidelines in lighting design and include a cultural dimension in the design of sustainable store environments.

Soil temperature is a fundamental parameter in water resources and engineering. A cost-effective model which can forecast soil temperature accurately is extensively needed. Recently, many studies have applied artificial intelligence (AI) at both surface and underground levels for soil temperature prediction. However, there is no comprehensive and detailed assessment of the performance of different AI approaches in soil temperature estimation, and primarily limited atmospheric variables are used as input data for AI models. In the present study, great varieties of various land and atmospheric variables are applied to evaluate the performance of a wide range of AI methods on soil temperature prediction. Herein, thirteen approaches, from classic regressions to well-established methods of random forest and gradient boosting to advanced AI techniques like multi-layer perceptron and deep learning are taken into account. The results show that AI is a promising approach in climate parameter forecast and deep learning demonstrates the best performance among other models. It has the highest R-squared ranging from 0.957 to 0.980, the lowest NRMSE ranging from 2.237% to 3.287% and the lowest MAE, ranging from 0.510 to 0.743 in predicting soil temperature. The prediction is repeated for different sizes of data, and prediction outcomes confirm the conclusion mentioned above.

Room temperature superconductivity has recently been reported for a carbonaceous sulfur hydride (CSH) under high pressure by Snider et al [1]. The paper reports sharp drops in magnetic susceptibility as a function of temperature for five different pressures, that are interpreted as signaling a superconducting transition. Here I question the validity and faithfulness of the magnetic susceptibility data presented in the paper by comparison with the measured raw data reported by two of the authors of ref. [2]. This invalidates the assertion of the paper [1] that the susceptibility measurements support the case for superconductivity in this compound.

With heat treatments to control drywood termites (Blattodea: Kalotermitidae), the presence of heat sinks causes heat to be distributed unevenly throughout the treatment areas. Drywood termites may move to galleries in heat sink areas to avoid exposure to lethal temperatures. Our studies were conducted in Crytotermes brevis-infested condominiums in Honolulu, Hawaii to reflect real-world condominium scenarios; either a standard heat treatment performed by a heat remediation company or an improved heat treatment was used. For improved treatments, heated air was directed into the toe-kick voids of C. brevis infested cabinets to reduce heat sink effects and increase the heat penetration into these difficult-to-heat areas. Eight thermistor sensors placed inside toe-kick voids, treatment zone, embedded inside cabinets’ sidewalls, and in a wooden cube recorded target temperatures of above 46 °C or 50 °C for 120 minutes. A pretreatment and follow-up inspections were performed at 6 months posttreatment to monitor termite inactivity using visual observations and by recording the numbers of spiked peaks on a microwave technology termite detection device (Termatrac). In improved treatment condominiums, significantly higher numbers of spiked peaks were recorded at pretreatment as compared to 6 months posttreatment. Efficacious heat treatment protocols using the improved methods are proposed.

Abiotic stress in plants is an increasingly common problem in agriculture, and thus, studies on plant treatments with specific certain compounds that may help to mitigate these effects have increased in recent years Melatonin (MET) application and its role in mitigating the negative effects of abiotic stress in plants have become important in the last few years. MET, a derivative of tryptophan, is an important plant-related response molecule involved in the growth, development, and reproduction of plants, and the induction of different stress factors. In addition, MET plays a protective role against different abiotic stresses such as salinity, high/low temperature, high light, waterlogging, nutrient deficiency and stress combination by regulating both the enzymatic and non-enzymatic antioxidant defense systems. Also, MET interacts with many signaling molecules, among these, reactive oxygen species (ROS) and nitric oxide (NO), and participates in a wide variety of physiological reactions. It is well known that NO produces S-nitrosylation and NO2-Tyr of important antioxidant-related proteins, being this an important mechanism for maintaining the antioxidant capacity of the AsA/GSH cycle under nitro-oxidative conditions, being extensively reviewed here under different abiotic stress conditions. Lastly, in this review, we show the coordination between NO and MET as a long-range signaling molecule, regulating many responses in plants, including plant growth and abiotic stress tolerance. Despite all the knowledge acquired over the years, there is still more to know about how MET and NO act on tolerance to abiotic stresses.

There is a lack of knowledge concerning the effects of ambient heat exposure on morbidity in Northern Europe. Therefore, this study aimed to evaluate the relationships of daily summer-time temperature and heatwaves with cardiorespiratory hospital admissions in the Helsinki metropolitan area, Finland. Methods: Time-series models adjusted for potential confounders such as air pollution were used to investigate the associations of daily temperature and heatwaves with cause-specific cardiorespiratory hospital admissions, during summer months of 2001-2017. Daily number of hospitalizations was obtained from the national hospital discharge register, weather information from the Finnish Meteorological Institute. Results: Increased daily temperature was associated with decreased risk of total respiratory hospital admissions and asthma. Heatwave days were associated with 20.5% (95% CI: 6.9, 35.9) increased risk of pneumonia admissions and during long or intense heatwaves also with total respiratory admissions in the oldest age group (≥ 75 years). There were also suggestive positive associations between heatwave days and admissions due to myocardial infarction and cerebrovascular diseases. In contrast, risk of arrhythmia admissions was decreased 20.8% (95% CI: 8.0, 31.8) during heatwaves. Conclusions: Heatwaves, rather than single hot days, are a health threat affecting the morbidity even in a Northern climate.

Although urbanization has contributed to improving living conditions, it has had negative impacts on the natural environment in the urbanized areas. Urbanization has changed the urban landscape and resulted in increasing land surface temperature (LST). Thus, studies related to LST in various urban environments have become a popular research topic. However, few LST studies focusing on the mountain landscapes (i.e. hill stations) have been carried out. The primary objective of this study is to investigate changes in the landscape and their impacts on LST intensity (LSTI) in the tropical mountain city of Nuwara Eliya, Sri Lanka. The study utilized annual median temperatures extracted from Landsat data collected from 1996 to 2017 based on the Google Earth Engine (GEE) interface. The fractions of built-up (BL), forest (FL), and agricultural (AL) land were calculated using land use and cover maps based on the urban-rural zone (URZ) analysis. The urban-rural margin was demarcated based on the fraction of BL (<10%) and LSTI was measured using the mean LST difference in the urban-rural zone. In addition, the mixture of land use types was calculated using the AL/FL and BL/FL fraction ratios, and grid-based density analysis. The result shows that the BL in all URZ rapidly developed, while AL decreased during the period 1996 to 2017. There was minimal change in the forest area of the Nuwara Eliya owing to the government forest preservation policies. The fraction of the BL increased from 32.4% in 1996 to 58.7% in 2017 in the city center zone (URZ₁) resulting in increased mean LST by 4.7 °C. Furthermore, the increase of the BL/FL fraction ratio and the decrease of the AL/FL fraction ratio were positively correlated with the mean LST. Grid-based analysis showed an increasing positive relationship between mean LST and density of BL. This indicated that BL density has been a crucial element in increasing LST in the study area. The results of this study will be a useful indicator to introduce improved landscape and urban planning in the future to minimize the negative impact of LST on urban sustainability.

In this article, the effect of substitution of Zr and Ga in Dy2Fe17 prepared by arc melting technique are studied. The substitution of Zr and Ga in Dy2Fe17 was found to have an important effect on their structure and magnetic properties. The Rietveld analysis conformed that the crystalline system wereTh2Ni17 structure. Lattice parameters a (Å) and c (Å), unit cell volume (Å3), bonding distance (Å) were calculated by using Rietveld analysis. The unit cell volume of Dy2Fe17-xZrx and Dy2Fe16Ga1-xZrx increase linearly with the Zr and Ga substitution. The substitution of Zr and Ga are limited up to x=1 in order to avoid the decrease in saturation magnetization. The Curie temperature (Tc) of Dy2Fe17-xZrx and Dy2Fe16Ga1-xZrx are found to be Zr content dependent. The Curie temperature is found to be increasing first and then decrease for higher Zr content. The maximum curie temperature was observed 510K at x = 0.75 for Dy2Fe17-xZrx and 505.1 K at x = 0.5 for Dy2Fe17-xZrx which are102 K and 97 K higher than Dy2Fe17. The room temperature Mössbauer analysis shows the decrease in average hyperfine field and increase in isomer shift with Zr doping.

1) Background: Climate change may subject forests to climate conditions to which they are not adapted. Elevated temperatures reduce net photosynthesis by increasing respiration rates and increasingly long droughts dramatically increase morbidity. CO₂ enrichment enhances productivity, but it is not clear to what extent CO₂ enrichment can offset the negative effects of elevated temperatures and longer droughts. 2) Methods: We used a mechanistic landscape model to conduct controlled simulation experiments manipulating CO₂ concentration, temperature, drought length and soil water capacity. 3) Results: We found that elevated CO₂ stimulates productivity such that it dwarfs the negative effect caused by elevated temperature. Energy reserves were not as strongly mitigated by elevated CO₂, and mortality of less competitive cohorts increased. Drought length had a surprisingly small effect on productivity measures, but had a marked negative effect on mortality risk. 4) Conclusions: Elevated CO₂ compensated for the negative effect of longer droughts in terms of productivity measures, but not survival measures.

This paper develops a novel dynamic correction method for the reliability assessment of large oil-immersed power transformers. First, with the transformer oil-paper insulation system (TOPIS) as the target of evaluation and the winding hot spot temperature (HST) as the core point, an HST-based static ageing failure model is built according to the Weibull distribution and Arrhenius reaction law, in order to describe the transformer ageing process and calculate the winding HST for obtaining the failure rate and life expectancy of TOPIS. A grey target theory based dynamic correction model is then developed, combined with the data of Dissolved Gas Analysis (DGA) in power transformer oil, in order to dynamically modify the life expectancy calculated by the built static model, such that the corresponding relationship between the state grade and life expectancy correction coefficient of TOPIS can be built. Furthermore, the life expectancy loss recovery factor is introduced to correct the life expectancy of TOPIS again. Lastly, a practical case study of an operating transformer has been undertaken, in which the failure rate curve after introducing dynamic corrections can be obtained for the reliability assessment of this transformer. The curve shows a better ability of tracking the actual reliability level of transformer, thus verifying the validity of the proposed method and providing a new way for transformer reliability assessment. This contribution presents a novel model for the reliability assessment of TOPIS, in which the DGA data, as a source of information for the dynamic correction, is processed based on the grey target theory, thus the internal faults of power transformer can be diagnosed accurately as well as its life expectancy updated in time, ensuring that the dynamic assessment values can commendably track and reflect the actual operation state of the power transformers.

The Microwave Humidity and Temperature sounder (MWHTS) on board the Fengyun (FY)-3C satellite measure the outgoing radiance form the Earth surface and atmospheric constituents. MWHTS makes measurements in the isolated oxygen absorption line near 118 GHz and the vicinity of strong water vapor line around 183 GHz, can provide fine vertical distribution structure of both atmospheric humidity and temperature. However, in order to obtain the accurate soundings of humidity and temperature by the physical retrieval method, bias between the observed radiance and those simulated by radiative transfer model from the background or first guess profiles must be correct. In this study, two bias correction methods are developed through the correlation analysis between MWHTS measurements and air mass identified by the first guess profiles of the physical inversion, one is the linear regression correction (LRC) and the other is neural networks correction (NNC), representing the linear and nonlinear nature between MWHTS measurements and air mass, respectively. Both correction methods have been applied to MWHTS observed brightness temperatures over the geographic area (180° W-180° E, 60° S-60° N). The corrected results are evaluated by the probability density function of the difference between corrected observations and simulated values and the root mean square error (RMSE) with respect to simulated observations. The numerical results show that the NNC method perform better, especially in MWHTS channels 1 and 7-9 whose peak weight function heights are close to the surface. In order to assess the effects of bias correction methods proposed in this study on the retrieval accuracy, a one-dimensional variational system was built and applied to the MWHTS uncorrected and corrected brightness temperatures to estimated atmospheric temperature and humidity profiles, The retrieval results show that the NNC has better performance which is to be expected. An indication of the stability and robustness of NNC method is given which suggests that the NNC method has promising application perspectives in the physical retrieval.

In China's mountainous coastal terrain, the storm badly damaged low-rise buildings. At present, it is not clear how the relative position of buildings and mountains affects the surface of a low-rise building’s fluctuating coefficient. The study compared these results with the wind pressure distribution without the surrounding environment. The primary objective of this study is to examine the fluctuating coefficient variation rule based on the spacing between hillsides and buildings under 0° wind angle. Additionally, the study analyzes the fluctuating wind pressure coefficient across wind angles between 0°~90°. The distribution of wind pressure in different common hillside landforms was examined through a wind tunnel experiment, which also compared with the distribution in an open environment. The study examined the fluctuating coefficient as the distance between the building and the hillside changed, specifically for wind blowing at a 0° angle. Next, an analysis is conducted on the changing pattern of the fluctuating coefficient for low-rise buildings ranging from a wind angle of 0° to 90°. Simultaneously, the investigation examined the power spectrum and wind pressure’s probability distribution, while considering the proximity of the building to an adjacent hill. The findings indicated that the changing wind pressure factor on the surface of the structure differed based on the relative location of the hillside and the building. The roof's wind pressure coefficient fluctuated and gradually increased until it reached its peak, unaffected by the surroundings. The low-frequency energy decreased in windward eaves, while the high-frequency energy progressively rose as the distance between the hillside and the building increased. The wind pressure on the leeward side exhibited Gaussian characteristics in its probability distribution.

Smart farm is a technology that greatly helps improve the productivity and quality of crops and is being actively introduced into indoor environments such as green houses. However, it has not yet been distributed to field-grown crops. The main reason is that, unlike indoor environments, it is very difficult to collect sensor data for monitoring the growth environment of crops in open fields where weather conditions change significantly and power supply is difficult. Additionally, because various sensors are used, the data formats of the devices are different, making it difficult to process. This paper presents a field crop growth environment monitoring and big data analysis system. The proposed system first solves power supply and data communication problems using solar power generation and LPWA technology. Additionally, based on the oneM2M architecture, data from various sensors is transmitted to the server using standardized technology. The transmitted data is stored and managed on the server as big data, and can be used to predict the production and quality of field-grown crops and take appropriate measures. The proposed system is expected to create an environment optimized for the growth of field crops and help prevent and manage diseases.

We offered the circuit of a discrete analog filter (DAF) low frequencies of second-order on switchable capacitors, which differs from the known ones in that three capacitors with one terminal are connected to a common bus, and the frequency of the DAF pole depends not only on the ratio of the capacitances of the frequency-setting capacitors, but also on the ratio of resistances two additional resistors in the feedback. This allows at constant values ​​of the capacitances and a fixed switching frequency of electronic switches, control the pole frequency by changing the resistance ratio of additional resistors. Computer simulation of the developed circuit was performed in the Micro-Cap environment. It has been established that the DAF has a transmission coefficient close to minus one at very low frequencies and a transmission coefficient close to zero at higher frequencies.

For many years, energy monitoring at the most disaggregate level has been mainly sought through the idea of Non-Intrusive Load Monitoring (NILM). Nevertheless, a practical application of this concept in the residential sector should address the underlying concerns raised by the technical specifications of case studies. From one side, such an operation must handle common matters related to the essence of any NILM system. Although this aspect has been thoroughly investigated by basic research, it is limited to the properties of public datasets. On the other side, it must deal with specific concerns corresponding to uncommon situations. These circumstances impose further restrictions on existent NILM schemes, however, they have been overlooked due to the lack of pertinent databases to scrutinize. Accordingly, this paper presents applied research on a potential solution to NILM for Quebec residences. It carries out a relevant investigation into the multi-faceted nature of this problem in order to reveal barriers to feasible implementations in the context of Quebec. This work commences with a concise discussion about the NILM idea to highlight its essential requirements for a fruitful practice. Afterward, it provides a comparative statistical analysis to represent the specificity and potential challenges of the case study in accordance with NILM necessities. For this purpose, the examination exploits data from real-world measurement systems in the same and European regions. Subsequently, this study focuses on a load identification exercise by proposing a combinatory approach that utilizes the promise of sub-meter smart technologies to integrate the intrusive aspect of load monitoring with the non-intrusive one. The former is aimed at extracting overall heating demand from the aggregate one by a supervised procedure based on Deep Learning (DL) models while the latter is designed for disaggregating the residual load through an unsupervised process on the basis of clustering techniques. The results demonstrate that geographically-dependent cases create electricity consumption scenarios under which existing NILM methods can be questioned. From a realistic standpoint, this research elaborates on critical remarks to realize viable NILM systems, particularly, in Quebec houses.

Low-sodium salt substitute (LSSS) has the potential in regulating sodium and potassium intake and has been available in China market for years. However, its real-world use and impact to sodium\potassium intake is unclear. Baseline data of 4000 adult participants who participated in three similar-designed randomized controlled trails were pooled together for this study. Self-reported awareness and use of LSSS were collected using the uniform questionnaire, and the 24-h urinary sodium and potassium excretion was used to estimate their dietary intake. Mixed-effects models were developed to assess the relationship between LSSS and 24-h urinary sodium and potassium excretion. 32.0% of the participants reported awareness of LSSS and 11.7% reported its current use. After adjusting location, sex, age, and education, compared with the group of participants unaware of LSSS, participants who were aware but not using LSSS and those who were using LSSS had a lower 24-h urinary sodium excretion by –356.1(95% CI: –503.9, –205.9) mg/d and –490.6(95% CI: –679.2, –293.7), respectively (p&lt;0.001). No significant difference was found for 24-h urinary potassium excretion and sodium-to-potassium ratio among the three groups (p&gt;0.05). In conclusion, although associated with lower sodium intake, the awareness and real-world use of LSSS are still very low in China.

An inter- and transdisciplinary concept has been developed, focusing on the scaling of industrial circular construction using innovative compacted mineral mixtures (CMM) derived from various soil types (sand, silt, clay) and recycled mineral waste. The concept aims to accelerate the systemic transformation of the construction industry towards carbon neutrality by promoting the large-scale adoption and automation of CMM-based construction materials, which incorporate natural mineral components and recycled aggregates or industrial by-products. In close collaboration with international and domestic stakeholders in the construction sector, the concept explores the integration of various CMM-based construction methods for producing wall elements in conventional building construction. Leveraging a digital urban mining platform, the concept aims to standardize the production process and enable mass-scale production. The ultimate goal is to fully harness the potential of automated CMM-based wall elements as a fast, competitive, emission-free, and recyclable alternative to traditional masonry and concrete construction techniques. To achieve this objective, the concept draws upon the latest advances in soil mechanics, rheology, and automation and incorporates open-source digital platform technologies to enhance data accessibility, processing, and knowledge acquisition. This will bolster confidence in CMM-based technologies and facilitate their widespread adoption. The extraordinary transfer potential of this approach necessitates both basic and applied research. As such, the proposed transformative, inter- and transdisciplinary concept will be conducted and synthesized using a comprehensive, holistic, and transfer-oriented methodology.

Urinary incontinence (UI) is a common geriatric syndrome affecting bladder health and is especially prevalent in nursing homes (NHs). The aim of the study was to determine the prevalence of UI and its associated factors in 5 Spanish NHs. UI (measured with Minimum Data Set 3.0.), sociodemographic and health-related variables were collected. Chi- square (or Fisher’s) or Student’s t-test (or Mann Whitney U) for bivariate analysis were used, with Prevalence Ratio (PR) as an association measure. The prevalence of UI was 66.1% (CI:95%, 53.6–77.2) and was significantly associated with frailty (PR 1.84; 95%CI 0.96–3.53), faecal incontinence (FI) (PR 1.65; 95%CI 1.02–2.65), anxiety (PR 1.64; 95%CI 1.01–2.66), physical performance (PR 1.77; 95%CI 1.00–3.11) and cognitive state (PR 1.95; 95%CI 1.05–3.60). Statistically significant differences between incontinent-continent groups were found for activities of daily living (ADL) limitations, mobility, quality of life, sedentary behaviour (SB) and handgrip strength. It can be concluded that 2/3 of the residents experienced UI, and its significant associated factors were mainly physical (SB, frailty, physical performance, ADL limitations, mobility, FI and handgrip strength) followed by psycho-cognitive factors (cognition, anxiety and quality of life).

Today, more disciplines are intercepting each other, giving rise to “cross-disciplinary” research. Technological advancements in material science and device structure and production have paved the way towards development of new classes of multi-purpose sensory devices. Organic phototransistors (OPTs) are photo-activated sensors based on organic field-effect transistors that convert incident light signals into electrical signals. The organic semiconductor (OSC) layer and three-electrode structure of an OPT offer great advantages for light detection compared to conventional photodetectors and photodiodes, due to their signal amplification and noise reduction characteristics. Solution processing of the active layer enables mass production of OPT devices at significantly reduced cost. The chemical structure of OSCs can be modified accordingly to fulfil detection at various wavelengths for different purposes. Organic phototransistors have attracted substantial interest in a variety of fields, namely biomedical, medical diagnostics, healthcare, energy, security, and environmental monitoring. Lightweight and mechanically flexible and wearable OPTs are suitable alternatives not only at clinical levels but also for point-of-care and home-assisted usage. In this review, we aim to explain different types, working mechanism and figures of merit of organic phototransistors and highlight the recent advances from the literature on development and implementation of OPTs for a broad range of research and real-life applications.

Insulin-like growth factor binding proteins (IGFBPs) are critical modulators of the metabolism. In adults, IGFBPs are associated with obesity and insulin resistance but the association of IGFBPs with metabolic homeostasis in children and adolescents is not fully characterized. In this study we investigated the association of plasma IGFBPs (IGFBP-1, 3 and 7) with weight status, central adiposity and cardiovascular disease markers Hs-CRP and Ox-LDL. A total of 420 adolescents (age 11-14 years) were randomly recruited from public middle schools in Kuwait. IGFBPs were measured using bead-based multiplexing while Hs-CRP and Ox-LDL were measured using ELISA. IGFBP-1 levels were significantly lower in obese and overweight participants compared to normal weight children. Only IGFBP-1 was negatively associated with waist circumference to height (WC/Ht) ratio. IGFBP-1 was negatively correlated with Hs-CRP while IGFBP-3 and IGFBP-7 were negatively correlated with Ox-LDL. These data demonstrate a robust negative association of IGFBP-1, but not IGFBP-3 or -7, with overweight and obesity, and the inflammation marker Hs-CRP. Central adiposity (WC/Ht ratio) was a stronger predictor of IGFBP-1 than BMI-for-age z-score. IGFBP-1 could thus be used as a sensitive predictive diagnostic tool for obesity and its subsequent effects in screening and monitoring of obesity-related metabolic complications in adolescents.

The epidemic transmission of Zika virus (ZIKV) in Brazil has been identified as a cause of microcephaly and other neurological malformations in babies of ZIKV-infected women. This study provides a descriptive analysis, since the onset of symptoms to the delivery, of a cohort who were registered as having ZIKV infection in pregnancy, from November 2015 to December 2016. Suspected cases were registered at a referral center for infectious and tropical diseases in Manaus, in the Brazilian Amazonian region. A total of 834 women with suspected ZIKV in pregnancy were included, of whom 91.4% had confirmed pregnancy. Reverse-transcriptase polymerase chain reaction (RT-PCR) confirmed ZIKV infection in 42.2% of the cohort. In 35.2% of the cohort, ZIKV was the sole infection identified. Severe adverse pregnancy outcomes (abortion, stillbirth, or microcephaly) were observed in both RT-PCR ZIKV-positive (4.96%) and ZIKV-negative (2.15%) cases. Women with suspected ZIKV infection were much more likely to have adverse pregnancy outcomes if they were symptomatic during the first trimester of pregnancy (odds ratio 10.5; 95% confidence interval 4.0–27.0; p<0.001). Among pregnant women with suspected ZIKV infection, the occurrence of symptoms in the first trimester is associated with an especially high risk of severe adverse pregnancy outcomes.

The slate aggregate has long been perceived as a substandard, low quality waste material with its physical and chemical properties not being competitive with those of the primary aggregates. It is assumed that the slate aggregate particles are not strong, that is not durable and will not compact. This research aims to address those claims and review the available literature on the performance of the slate aggregate. The review inaugurates by analysing the physical, chemical and mechanical properties of slate, before expanding into a literature review of laboratory testing’s on the effect of moisture content on density, compaction and layer thickness of slate aggregate.The paper reviews case studies of construction projects in North Wales, where the slate aggregate has been used for general fill and road building for many years. Some of the case studies include the A55 coastal road and duelling of the A5 in Anglesey (WRAP, 2004), where slate aggregate was successfully used as sub-base. The paper also investigates why many civil engineers are reluctant to use the slate aggregate and regard the material as sub-standard, flaky aggregate. The research paper reviews the potential usages and various products the slate aggregate is suitable for and satisfies the requested standards. The final topic reviewed is the cost of transporting slate aggregate compared with the cost of transport for primary aggregate and the introduction of the Primary Aggregates Tax (Parliament of the United Kingdom, 2011). The last topic includes a critical analyses of the claims that the slate aggregate a commercially viable construction material despite its remote location (Woodward et al, 2004). The transportation cost and the supply chain complexities must be evaluated prior to considering the long-term sustainability of the product (Radanliev et al^1-6, 2014, 2015, 2016).

In order to further control the equivalent circulating density,a new type of annular pres-sure-reducing downhole tool for high temperature and high pressure wells-liquid-absorbing ECD tool is designed.Through this tool,the bottom hole pressure of the equivalent circulating drilling fluid can be close to its hydrostatic pres-sure,therebyachieving a deeper drilling depth.The tool is mainly composed of screw mo-tor,vortex blade,annular seal,universal joint and drill string.Its working principle is mainly to use the liquid absorption effect of the tool and the hydraulic energy of the circu-lating fluid extracted by the screw motor to convert it into mechanical energy,and to gen-erate suction force to improve the flow energy of the drilling fluid in the bottom hole an-nulusand reduce the equivalent circulation density.Based on ANSYS-FLUENT analysis andsimulation,the change of pressure drop characteristics under different drilling fluid density,displacement and tool size was simulated.The simulation results show that thedepressurization effect is 1.0MPa when the drilling fluid density is 1.2g/cm3. When the drilling fluid density is 1.5g/cm3,the depressurization is about 1.7MPa,and when thedrill-ing fluid density is 1.8g/cm3,the depressurization is about 1.9MPa.When the drilling fluid density is 2.0g/cm3,the pressure drop is about 2.3MPa.When the flow rate is from 1500-2500L/min,the maximum pressure can be reduced by 2.3MPa.When the viscosity is 40mPa•S and 60mPa•S,the pressure drop almost does not change.The increase of viscosi-ty has little effect on the pressure drop,and it is mainly affected by the flow rate under equal displacement.

The bipartite entanglement is comprehensively investigated in the mononuclear molecular complex (Et3NH)[Ni(hfac)2L], where HL denotes 2-(2-hydroxy-3-methoxy-5-nitrophenyl)-4,4,5,5-tetramethyl-4,5-dihydro-1H-imidazol-3-oxide-1-oxyl and hfacH stands for hexafluoroacetylacetone. From the magnetic point of view, the molecular compound (Et3NH)[Ni(hfac)2L] consists of an exchange-coupled spin-1 Ni2+ magnetic ion and a spin-12 nitronyl-nitroxide radical substituted nitrophenol. The nickel-radical molecular complex affords an experimental realization of a mixed spin-(12, 1) Heisenberg dimer with a strong antiferromagnetic exchange coupling J/kB= 505 K and two distinct g-factors gRad=2.005 and gNi=2.275. By adopting this set of magnetic parameters we demonstrate that the Zeeman splitting of a quantum ferrimagnetic ground-state doublet due to a weak magnetic field may substantially reinforce the strength of bipartite entanglement at low temperatures. The molecular compound (Et3NH)[Ni(hfac)2L] maintains sufficiently strong thermal entanglement even at room temperature, vanishing only above 546 K. Specifically, the thermal entanglement in the nickel-radical molecular complex retains approximately 40% of the maximum value corresponding to perfectly entangled Bell states at room temperature, which implies that this magnetic compound provides suitable platform of a molecular qubit with potential implications for room-temperature quantum computation and quantum information processing.

In this paper, the Shannon entropy measure was used to assess changes in precipitation and temperature conditions. Due to the short, low-volume sequences of precipitation and temperature data analysed, a bootstrap method was used in the procedure for calculating Shannon entropy. The analysis used minimum and maximum values of monthly precipitation totals and monthly mean temperatures for 377 catchments distributed across the globe. A 110-year data series from 1901 to 2010 was analysed. Entropy values for the estimated parameters of the generalised extreme value distribution (GEV) were calculated for the adopted data. Entropy value calculations were performed for the left-hand constraint, based on minimum values, and for the right-hand constraint, based on maximum values. The applicability of Shannon's entropy measure in the analysis of climate change was demonstrated by allowing the degree of disorder and complexity of the distributions describing climate variables in the form of precipitation and temperature to be measured. This made it possible to obtain information on the directions of changes occurring with regard to minimum and maximum values in the field of monthly precipitation and mean temperatures in the analysed catchments. The study demonstrated the existence of Shannon entropy trends. The evaluation of entropy trends for precipitation and temperature sequences was performed using non-parametric tests. Mann -Kendall tests at the 5% significance level were used for trend analyses. The Pettitt test was performed to determine the point of change in trend for the rainfall and temperature data. The performed analysis was supported by graphical presentations.

Two pre-pulses focused at different positions and at different time moments were used to enhance THz emission generated by the main pulse. The emission of THz radiation from air breakdown regions of focused ultrashort fs-laser pulses (800 nm/35 fs) at shockwave front prepared by pre-pulses was investigated, and a 3D spatio-temporal control was established for the most intense emission. The laser pulse-induced air breakdown forms a ~120 micrometers-long focal volume and generates a shockwave that delivers denser air into the focal region of the main pulse for enhanced generation of THz radiation at 0.1-2.5 THz spectral window. The intensity of pre- and main-pulses was at the tunneling ionisation intensities (1-3)x10¹⁶ W/cm² and corresponded to sub-critical (transparent) plasma in air. Polarisation analysis revealed that the orientation of the air density gradients generated by pre-pulses and their time-space placement defined the ellipticity of the generated THz electrical field. The rotational electric current is the origin of THz radiation. The current is created by non-parallel gradients of electron density and temperature. Scaling dependencies of THz emission control are established.

In this research paper an algorithm for the derivation of methods based on theorems and axioms of fuzzy logic is presented, analyzed and applied. This new proposed procedure generates fuzzy methods and evaluates the value of fuzzy propositions through fuzzy implication. The new implications of the family should satisfy a number of axioms. Also, we denote the conditions in order to satisfy the maximum number of axioms. Moreover, authors state and prove theorems focusing on fuzzy implication, observing the rule: the fuzzy function of fuzzy implication is strong and that lead to fuzzy negation. In addition, the optimal number of repetitions is calculated according to the expected truth value. The formulas produced are verified through the use of temperature and humidity values over a certain period of time and in a certain geographical area in Greece. The basic steps of the methodology are the fuzzification of the data given ​​using four membership degree functions and the application of the membership degrees of temperature and humidity values on a new type of fuzzy implication. Finally, we observed that the isosceles trapezium gave the best results and the type of fuzzy implication can be effectively applied.

This paper presents the results of a comparison of the seasonal dynamics of carbon dioxide content in the atmosphere and the phenological phases of various water bodies located in the boreal and subarctic zones for 2012–2020. Six large freshwater areas were selected as research objects: Lake Baikal, Lake Ladoga, Gulf of Ob, Lake Huron, Great Bear Lake and Great Slave Lake. In addition, four areas of wetlands in Western Siberia were studied. The CO2 concentration in the air column over water bodies was obtained from CAMS global greenhouse gas reanalysis data. These data represent three-dimensional fields of aerosols and chemical components in the atmosphere, with complete coverage of the globe. The phenological phases of the water bodies were determined using data from the MIRAS microwave radiometer of the SMOS satellite. The comparison and analysis performed showed that the concentration of CO2 in the atmosphere over the studied water bodies has a seasonal cyclical nature. The minimum concentration corresponds to the summer period due to strong photosynthesis of phytoplankton and swamp vegetation, which results in the absorption of carbon dioxide. The maximum CO2 concentration over the water bodies corresponds to the end of the winter – the beginning of the spring period, when photosynthesis processes are minimal. During this period, CO2 is being accumulated in water bodies and subsequently emitted. In freezing lakes located in the boreal zone, in addition to a stable spring maximum of CO2, a strong short-term release of carbon dioxide is sometimes observed, also corresponding to the stage of destruction of the ice cover. It is associated with the release of CO2 accumulated over the winter period, which was “sealed” in the ice and in the water column under the ice. The absence of such a release in the waters of the subarctic zone is explained by the lower biological productivity of these reservoirs compared to the waters of the boreal zone.

This article presents an analysis of monthly precipitation totals based on the Global Precipitation Climatology Centre database and monthly mean temperatures based on National Oceanic and Atmospheric Administration data for 377 catchments located around the world. Data sequences covering 110 years from 1901 to 2010 were analysed. The long-term sequences of precipitation and temperature were used to assess the variability of climate extremes, referred to here as polarisation. Measures of polarisation used in the natural sciences are discussed. A simple measure of polarisation was presented and applied to long-term sequences of monthly precipitation totals and monthly mean temperatures. Due to the nature of the proposed polarisation measure, other characteristics of precipitation and temperature sequences are also presented as a background for the discussion of the polarisation index. The study showed the existence of trends related to the polarisation of temperature and precipitation phenomena. As a result of the analysis, trends of polarisation factors in the area of precipitation and temperature were identified in 11 catchments out of the 377 analysed catchments. The trend analysis used Mann-Kendall tests at a level of significance of 5%. The Pettitt test was used to determine the point of trend change for precipitation and temperature data. The whole investigation is supported by rich graphical analyses, and the results are presented in tabular form.

With simple but rigorous arguments we prove that the ordinary second quantization of bosonic and fermionc fields is formally equivalent to constraining the elementary degrees of freedom of the classical fields to have intrinsically periodic dynamics in time. This result confirms and extends the formal equivalence obtained in previous papers for general Hamiltonian systems in terms of canonical quantization, for elementary relativistic particles also in terms of the Feynman Path Integrals, as well as other remarkable correspondences of both phenomenological and theoretical fundamental interest.

The article presents an analysis of monthly precipitation totals based on the GPCC database, and monthly mean temperatures (NOAA data) for 377 catchments distributed across the globe. The analysis included 110-year data sequences from 1901 to 2010 calculated from grid data with a spatial resolution of 0.5°x 0.5° longitude and latitude. Long-term sequences of precipitation and temperature were used to assess the polarization of climatic phenomena. The noticeable impact of polarization in the area of extreme changes in temperature and precipitation is related to anthropogenic factors such as greenhouse gas emissions, deforestation and pollution, which affect ecosystem functioning, biodiversity, water resources and economies. The paper demonstrates the existence of trends related to the polarization of temperature and precipitation phenomena. The measures of polarization used in science are discussed. A simple measure of polarization was proposed and applied to both long-term sequences of monthly precipitation totals and monthly mean temperature. Due to the nature of the proposed polarization measure, other characteristics of the precipitation and temperature sequences are also presented as background for the discussion of the polarization index. The paper presents, for a selection of several hundred catchments from around the world, analyses of the assessment of precipitation and temperature trends using non-parametric tests. The trend analyses use Mann -Kendall tests at the 5% significance level. A Pettitt test was used to determine the trend change point for precipitation and temperature data. The whole is supported by rich graphical analyses and the results are presented tabularly.

For the first time, few-layer graphene (FLG) nanosheets were synthesized by the method of self-propagating high-temperature synthesis (SHS) from biopolymers (starch and lignin). We suggested that biopolymers (lignin, tree bark) and polysaccharides, in particular starch, could be an acceptable source of native cycles for the SHS process. The carbonization of biopolymers under the conditions of the SHS process was chosen as the basic method of synthesis. Chemical reactions, under the conditions of the SHS process, proceed according to a specific mechanism of nonsothermal branched-chain processes, which are characterized by the joint action of two fundamentally different process-accelerating factors - avalanche reproduction of active intermediate particles and self-heating. The method of obtaining FLG nanosheets included the thermal destruction of hydrocarbons in a mixture with an oxidizing agent. We used biopolymers as hydrocarbons and ammonium nitrate as an oxidizing agent. Thermal destruction was carried out in the mode of SHS, heating the mixture in a vessel at a speed of 20–30 oC/min to 150-200 oC and keeping at this temperature for 15–20 min with the discharge of excess gases into atmosphere. A combination of spectrometric research methods, supplemented by electron microscopy data, has shown that the particles of the carbonated product powder in their morphometric and physical parameters correspond to FLG nanosheets. An X-ray diffraction analysis of the indicated FLG nanosheets was carried out, which showed the absence of formations with a graphite crystal structure in the final material. The surface morphology was also studied and the features of the IR absorption of FLG nanosheets were analyzed. It is shown that the developed SHS method makes it possible to obtain FLG nanosheets with linear dimensions of tens of microns and a thickness of not more than 1-5 graphene layers (several graphene layers).

Climate change is expected to increase the frequency and severity of abiotic stresses that lead to loss of crop yield. We investigated the effect of salinity (S), short episodes of high temperature (HS) and combination of S+HS at the reproductive phase on dead pericarps properties and yield of the crop plant Brassica juncea. Three intervals of HS resulted in massive seed abortion; seeds from salt-treated plants germinated poorly. Pericarp extracts of salt-treated plants reduced seed germination of B. juncea; all pericarp extracts completely inhibited seed germination of tomato and Arabidopsis; removal of pericarp extracts restored seed germination. HS reduced all metabolites accumulated in dead pericarps, except for upregulation of isomaltose and cellobiose. Salt induced alteration in metabolite levels including increase in proline, reduction in TCA intermediates and changes in phytohormone levels. Proteome analysis revealed hundreds of proteins stored in dead pericarps whose levels and composition were altered under salt stress. The integration of metabolic and proteomic data showed that changes in metabolites were highly correlated with changes in proteins involved in their biosynthetic pathways. Thus, besides providing a physical shield for seed/embryo protection dead pericarps store beneficial substances whose levels, composition and biological function are altered under stress, further highlighting the elaborated function of dead organs enclosing embryos in seed biology and ecology. The detrimental effect of HS on crop production might have implications for global food security in the face of climate change.

Laser powder bed fusion (LPBF) is an additive manufacturing process employed in many industries, for example for aerospace, automotive and medical applications. In these sectors, mainly nickel-, aluminum- and titanium-based alloys are used. In contrast, the mechanical engineering industry is interested in more wear-resistant steel alloys with higher hardness, both of which can be achieved with a higher carbon content, like in high-speed steels. Since these steels are susceptible to cracking, preheating needs to be applied during processing by LPBF. In a previous study, we applied a base plate preheating temperature of 500 °C for HS6-5-3-8 with 1.3 % carbon content. We were able to manufacture dense (p > 99.9 %) and crack-free parts from HS6-5-3-8 with a hardness > 62 HRC (as built) by LPBF. In this study, we investigate the influence of preheating temperatures up to 600 °C on hardness and microstructure dependent on part height for HS6-5-3-8. The microstructure was studied by light optical microscopy (LOM), scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD). The analysis of hardness and microstructure at different part heights is necessary because state-of-the-art preheating systems induce heat only into the base plate. Consequently, parts are subjected to temperature gradients and different heat treatment effects depending on part height during the LPBF process.

In this work we have critically reviewed the processes in high-temperature sublimation growth of graphene in Ar atmosphere using enclosed graphite crucible. Special focus is put on buffer layer formation and free charge carrier properties of monolayer graphene and quasi-freestanding monolayer garphene on 4H-SiC. We show that by introducing Ar at different temperatures, TAr one can shift to higher temperatures the formation of the buffer layer for both n-type and semi-insulating substrates. A scenario explaining the observed suppresed formation of buffer layer at higher TAr is proposed and discussed. Increased TAr is also shown to reduce the sp3 hybridization content and defect densities in the buffer layer on n-type conductive substrates. Growth on semi-insulating substrates results in ordered buffer layer with significantly improved structural properties, for which TAr plays only a minor role. The free charge density and mobility parameters of monolayer graphene and quasi-freestanding monolayer graphene with different TAr and different environmental treatment conditions are determined by contactless terahertz optical Hall effect. An efficient annealing of donors on and near the SiC surface takes place in intrinsic monolayer graphene grown at 2000∘C, and which is found to be independent of TAr. Higher TAr leads to higher free charge carrier mobility parameters in both intrinsically n-type and ambient p-type doped monolayer graphene. TAr is also found to have a profound effect on the free hole parameters of quasi-freestanding monolayer graphene. These findings are discussed in view of interface and buffer layer properties in order to construct a comprehensive picture of high-temperature sublimation growth and provide guidance for growth parameters optimization depending on the targeted graphene application.

Land Surface Temperature (LST) and Land Use Land Cover (LULC) are the principal aspects of climate and environment studies. The object of the study is to assess spatial relationship between LST and remote sensing LULC indices at the global and continental scale. Moderate Resolution Imaging Spectroradiometer (MODIS) Aqua daytime LST and eight LULC MODIS indices of 2018 prepared and processed using Earth Engine Code Editor. R squared and significance of the relationship values of randomly selected points computed in R program. The research observed the relationship between examined indices and LST is significant at the 0.001 level. Normalized Difference Water Index (NDWI) and Normalized Difference Snow Index (DSI) are the dominant drivers of LST in the world, Asia and North America. In Australia and Africa, Normalized Difference Vegetation Index (NDVI) and Enhanced Vegetation Index (EVI) are the dominant drivers of LST. Albedo and Normalized Difference Soil Index (NDSI) have superior in Central America. In South America and Europe, the dominant driver of LST is NDWI. Relationship between albedo and LST is moderate inverse on a global scale. Observed relationship between LST and examined vegetation indices is positive in Europe and North America while inverse in Australia and Africa. All observed relationship between Normalized Difference Built-up Index (NDBI) and LST are positive. Association observed between NDSI and LST is positive in Australia, Africa and Central America.

A ducted photovoltaic façade (DPV) unit Studied using experimental Prototype and simulated in a full scale Computational Fluid Dynamics CFD Model. The Study comes in two parts; This is Part I with the title detailed above and Part II titled ‘A Ducted Photovoltaic Façade Unit with Buoyancy Cooling: Part II CFD Simulation’.. The process adopted in the experimental study is replicated in the simulation Part. The aim was to optimize the duct width behind the solar cells to allow for maximum buoyancy-driven cooling for the cells during operation. Duct widths from 5 to 50 cm were tested in a Proto-type. A duct width of 45 cm had the maximum calculated heat removed from the duct; however, the lowest cell-operating temperature was reported for duct width of 50 cm. It was found that the DT between ducts' inlets and outlets range from 5.47 °C to 12.32 °C for duct widths of 5–50 cm, respectively. The ducted system enhanced module efficiency by 12.69% by reducing PV temperature by 27 °C from 100°C to 73 °C. The maximum calculated heat recovered from the ducted PV system is 422 W. This is 47.98% from the incident radiation in the test. Total summation of heat recovered and power enhanced by the ducted system is 61.67%.

Direct laser writing three-dimensional nano-lithography is an established technique for manufacturing functional 3D micro- and nano-objects via non-linear absorption induced polymerization process. In this Chapter an underlying physical mechanisms taking place during nano-confined polymerization reaction, induced by tightly focused ultra-short laser pulses, are reviewed and discussed. The special attention is paid on the effects that directly impact structuring resolution and minimum achievable feature size. Analysis of possible photo-initiation mechanisms as contributing multi-photon absorption and avalanche ionization in pre-polymers under diverse exposure conditions (wavelength, pulse duration) is presented. Feasible structuring of pure (non-photosensitized) and functional nanoparticles doped polymer precursors is justified and benefits of such materials/structures for microoptics, photonics and cell scaffolds are highlighted. The influence of temperature effects (induced by writing process itself or determined by ambient conditions) on polymerization process, observed in different pre-polymers under diverse exposure regimes is outlined. The further adjustment of the structuring resolution is possible via precise control of light polarization and diffusion assisted radical quenching. The work is concluded with a brief outlook on future challenges and perspectives related to refinement of 3D ultra-fast laser lithography fabrication process in the means of application of diverse post-processing methods and research into novel photo-curable materials including inorganic ones.

External quantum efficiency of industrial-grade green InGaN light-emitting diodes (LEDs) has been measured in a wide range of operating currents at various temperatures from 13 K to 300 K. Unlike blue LEDs, the efficiency as a function of current is found to have a multi-peak character, which could not be fitted by a simple ABC-model. This observation correlated with splitting of LED emission spectra into two peaks at certain currents. The characterization data are interpreted in terms of non-uniformity of the LED active region, which is tentatively attributed to extended defects like V-pits. We suggest a new approach to evaluation of temperature-dependent light extraction and internal quantum efficiencies taking into account the active region non-uniformity. As a result, the temperature dependence of light extraction and internal quantum efficiencies have been evaluated in the temperature range mentioned above and compared with those of blue LEDs.

Emerging evidence suggests that low socioeconomic status (SES) home environments may play a role by promoting excess energy intake through a lack of access to non-food reinforcers. Because of the deleterious effects of SES related disparities on child health and development, feasible and culturally acceptable interventions are urgently needed. Community-based music enrichment programs may be an ideal intervention strategy. In collaboration with a local non-profit organization and music studio, we conducted a pilot randomized controlled trial to assess the effects of a music enrichment program versus playdate control in a group of 9-24-month-old healthy infants (N = 16). Overall, we found some intervention effects on relative reinforcing value of food (RRVfood) and the home environmental enrichment measures (i.e., increased music use at home and home language environment). Our intervention demonstrated large effects on an increased use of music at home. We did not find significant group differences on the RRVfood and home language environment, but some of the effect sizes were medium-to-large. Results also suggest that our intervention is feasible and acceptable. Parent feedback indicated the intervention was well-liked and steps we took to help reduce barriers worked. Music enrichment programs maybe a high-impact, low-cost strategy to address socioeconomic disparities.

Gas-water relative permeability curve is the foundation of gas reservoir dynamic analysis and numerical simulation. It is generally obtained through gas displacing water experiment. Referring to the existing national standards, gas-water relative permeability test is carried out for low-permeability and tight sandstone. The flow is discontinuous and the curve smoothness is poor, which affects the application of gas-water relative permeability curve. Based on the comparative analysis of a large number of mercury injection and NMR experimental results of low-permeability and tight sandstone, a method to characterize the throat radius distribution of low-permeability tight sandstone based on NMR T2 spectrum is explored. Combined with high-speed centrifugal experiment, the calculation formulas of core water saturation, phase relative permeability of gas-water under different centrifugal force are established. A new method of "nuclear magnetic resonance + high-speed centrifugation" for gas-water relative permeability curve test of low-permeability and tight sandstone is formed, and the test is carried out on Sulige low-permeability tight sandstone core. The results show that: (1) The shape of cumulative distribution curve of throat radius by mercury injection method is basically consistent with that of T2 relaxation time by NMR, and there is a good corresponding relationship between them. (2) The centrifugation process is similar to the gas displacing water process. With the decrease of water saturation, water centrifugation in rock core becomes more and more difficult until it become irreducible. (3) The test process of the new method is unified and standard and up to 6 cores can be tested at the same time. The calculation results of water saturation and relative permeability curve are reliable and the integral curve is smooth, which greatly improves the test efficiency of gas-water relative permeability curve in low-permeability and tight sandstone. The new method can be widely used to study the gas-water two-phase seepage law in low-permeability and tight sandstone gas reservoir.

A model for enabling the production of lower carbon cement paste is proposed in this research. The model is based on predicting the strength of cement pastes with partial replacement of wheat straw ash (WSA) and silica fume (SF), two major wastes of agricultural and industrial production. The model is set up based on response surface methodology and Box-Behnken design, and included a suite of mechanical tests with distinct replacements following a micro an meso characterization. The model shows capability for predicting strength of any cement paste, including partial substitution of WSA and/or SF at any combination level with excellent accuracy, which is verified with three validation mixtures demonstrating maximum errors of less than 6% at the three ages. The analysis of the response surface evidences that any cement replacement in the range of 0-20% WSA and above 5% SF allows the reduction of the carbon footprint by maximizing the incorporation of both wastes. The proposed model can be used by setting the required strength of cement paste and calculating the maximum possible replacement, which should contribute to making the construction industry more sustainable by utilizing local waste.

The paper describes an application of machine learning approach for parameter optimization. The method is demonstrated for the elasto-viscoplastic model with both isotropic and kinematic hardening. It is shown that the proposed method based on long-short term memory networks enabled to obtain reasonable agreement of stress-strain curves for cyclic deformation in low-cycle fatigue regime. The main advantage of the proposed approach over traditional optimization schemes lies in the possibility to get parameters for a new material without the necessity to conduct any further optimizations. As the power and robustness of the developed method was demonstrated on the very challenging problem (cyclic deformation, crystal plasticity, self-consistent model, isotropic and kinematic hardening), it is directly applicable to other experiments and models.

Abstract—The static and fatigue analysis of plates with holes, made of 2D woven roving composites, is conducted. The parametrization of convex holes is proposed. Experimental results of specimens without holes and with different shapes of notches are discussed. The fatigue behaviour is considered with the use of the low cycle fatigue method. The analysis is supplemented by the numerical finite element modeling. The present work is an extension of the results discussed in the literature. The finite element modeling of plates with holes is presented in details in Ref [1-3] including also the problems of the accuracy. The experimental results and the form of specimens are shown in Ref [4]. Two parametrical description of static and fatigue behaviour of plates with holes characterizes the goal and the novelty of the paper. The fuzzy approach is employed to reduce the number of experimental data [5].

While providing safe water for the rural poor is considered a basic human right, there are numerous issues associated with existing technologies with shortcomings. Performance issues have continued to fail to meet the needs of impoverished families due to issues including high cost, difficulties with performance, and continuing needs for maintenance. These issues have severely interfered the safe water accessibility. Key aspects of the Guelph Water Filter (GWF) system can avoid/minimize many of these issues. The GWF as described herein enables delivery of low cost, long-term performance at 3Log removal of E.coli and can deliver 1 to 3 L of treated water per hour. The GWF is simple to operate, has an ability to provide sufficient water for a family, maintains longevity of performance, is easy to maintain and has protection against breakage during the cleaning process, is repairable at village level, and operates using a sizable reservoir of water to supply raw water, meaning the technology does not need to be refilled frequently. Hence, the capability of the novel GWF technology is shown to bypass many of the troublesome features of alternative low-tech water treatment technologies. The potential for the GWF to function for 2 days continuously avoids the need for young girls to fetch raw water frequently during a day, thereby enabling them to attend school. Hence, the GWF enhances the potential to result in ‘safe water and full schools’, providing the opportunity for girls to receive education and capture socio-economic benefits for the community.

Human epidermal growth factor receptor 2 (HER2) belongs to the ErbB family, a group of four transmembrane glycoproteins with tyrosine kinase activity, all structurally related to the epidermal growth factor receptor (EGFR). These tyrosine kinases are involved in the transmission of cellular signals controlling normal cell growth and differentiation. If this transmission goes awry, it can lead to dysregulated growth of the cell. HER2 specifically can be implicated in the pathogenesis of at least eight malignancies. HER2 positivity quickly became a well characterized indicator of aggressiveness and poor prognosis, with high rates of disease progression and mortality. After realizing the implication of HER2, it first became investigated as a target for treatment in breast cancer, and later expanded to areas of research in other cancers types. To this day, the most therapeutic advancements of anti-HER2 therapy have been in breast cancer, however, there have been strong advancements made in the incorporation of anti HER2 therapy in other cancer types as well. This comprehensive review dissects HER2 to its core incorporating the most up to date information. The topics touched upon are discussed in detail and up to 200 published sources from the most highly recognized journals have been integrated. The importance of knowing about HER2 is exemplified by the groundbreaking advancements that have been made, and the change in treatment plans it has brought to the oncological world in the last twenty years. Since, its ground breaking discovery there has been significant breakthroughs in knowledge regarding the actual receptor, the receptors biology, its mechanism of action, advancements in tests to detect HER2 and significant strides on how to best incorporate targeted treatment. Due to the success of this field thus far, the review concludes by discussing the future of novel anti-HER2 therapy currently in development that everyone should be aware of.

Iterative Stochastic decoding is an alternative to standard fixed-point decoding of Low-density parity check codes (LDPC) to reduce inter-node routing. In this paper, we propose a Flexible Field-Programmable Gate Array (FPGA)-Based Stochastic decoding (SD) hardware architecture for LDPC codes in the Fifth-Generation (5G) New Radio (NR) Standard that supports decoding of set of various code rates. This decoder’s runtime flexibility is desirable to switch a better performing code rate automatically based on the channel conditions without the extra time needed for reprogramming of FPGA. An offline design method is implemented to generate the hardware description language (HDL) code description of the decoder for the required code-rate set, which is further synthesized and integrated into the Xilinx Kintex-7 series FPGA board to determine the hardware resource utilisation and processing throughput. The Synopsys design tools were employed during both the simulation and synthesis stages, in combination with TSMC 65-nm CMOS standard cell technology, to facilitate comparative analysis. Compared with state-of-the-art designs, the proposed architecture reduces hardware utilization by up to 26% and achieved energy efficiency by 52%.

Our objective was to evaluate whether pregnancy is prolonged by use of a proteomics-based maternal serum screening test followed by treatment interventions. This is a secondary analysis of the PREVENT-PTB randomized trial comparing screening with the PreTRM test versus no screening. The primary trial analysis found no significant between-group difference in preterm birth rate. Rather than considering a dichotomous outcome (preterm vs term), we treated gestational age at birth as a continuous variable using survival analysis. We also evaluated between-group difference in NICU length of stay and duration of respiratory support. Results indicated that pregnancy was significantly prolonged in subjects screened with PreTRM test compared to controls (adjusted hazard ratio 0.53, 95% confidence interval 0.36-0.78, P &lt;0.01). Newborns of screened subjects had significantly shorter NICU stay but no significant decrease in duration of respiratory support. In the PreTRM screen-positive group, interventions that were associated with pregnancy prolongation included care management and low-dose aspirin but not 17-hydroxyprogesterone caproate. We concluded that screening with the PreTRM test followed by interventions for screen-positive pregnancies can prolong pregnancy and reduce NICU-LOS.

Applications for Wireless Sensor Networks (WSNs) range from monitoring the environment to automating factories. However, sustained and effective functioning is made more difficult by Sensor Nodes (SNs) limited energy supplies in which optimization is the main issue. So with the aim of increasing the lifespan by decreasing the energy consumption of WSN, Low-Energy Adaptive Clustering Hierarchy (LEACH) protocol with Deep Learning (DL) algorithm is analyzed in this paper. LEACH is a hierarchical mechanism that elects Cluster Heads (CHs) and regularly rotates their positions in order to allocate energy use effectively by using the same amount of energy. However, Deep Learning (DL) method is used to further improve energy optimization. In many applications, the types of Deep Learning methods like Artificial Neural Networks (ANNs) have shown to be very useful. Using this method, WSNs may make more efficient decisions that reduce energy consumption. Data aggregation, duty cycling, and transmission protocols may all be optimized by Deep Learning model's ability to recognize patterns and forecast network behavior. This results in lower energy consumption, a longer lifespan for the network, and better overall performance.

Powerful emitters of the ultraviolet C (UVC) light in the wavelength range of 230-280nm are necessary for the development of effective and safe optical disinfection technologies, high-sensitive optical spectroscopy and non-line-of-sight optical communication. This review considers such UVC-emitters with electron-beam pumping of heterostructures with quantum wells in the (Al,Ga)N material system. The important advantages of these emitters include the absence of the critical problem of p-type doping and the possibility of achieving record (up to several tens of watts for peak values) output optical power values in the UVC range. The review consistently considers about a decade of world experience in the implementation of various UV emitters with various types of thermionic, field-emission, and plasma-cathode electron guns (sources) used to excite various designs of active (light-emitting) regions in heterostructures with quantum wells AlxGa1-xN/AlyGa1-yN (x = 0 − 0.5, y = 0.6 − 1) fabricated either by metal-organic chemical vapor deposition or by plasma-activated molecular beam epitaxy. Special attention is paid to the production of heterostructures with multiple quantum wells/two-dimensional(2D) quantum disks GaN/AlN with a monolayer (1ML ~ 0.25nm) thickness, which ensures a high internal quantum efficiency of radiative recombination in the UVC range, low elastic stresses in heterostructures, and a high output UVC-optical powers.

The DNS of film boiling requires strong computational resources that are difficult to obtain for a daily CFD use by the practitioners of the industrial R&amp;D experts. On the other hand, the film boiling experiments are associated with the usage of the expensive and highly sophisticated apparatus, and the research to this end is found to be relatively difficult due to high heat flow rates that are present in the process itself. When combined with a transient heat conduction in a solid, the problem becomes significantly difficult. Therefore, a novel method in computation of conjugate heat transfer during film boiling in a quiescent liquid has been proposed in this paper. The method relies on the solution of mass, momentum and energy conservation equations in a two-fluid framework, supplemented with the appropriate closures. Furthermore, the turbulent flow has been found as an important parameter in obtaining the accurate solution of the temperature field evolution in a solid specimen, via the proper modeling of turbulent kinetic energy (TKE) value, that has been imposed as a constant value, i.e., the frozen turbulence approach. It was found, in addition, that the appropriate TKE value can be obtained by use of Kelvin-Helmholtz instability theory in conjunction with the boundary layer theory. The obtained results show excellent agreement with the experimental data within the first 15 s of the experiment, i.e., the first ca. 10 % of the total duration of the film boiling mode of heat transfer. Furthermore, the heat transfer coefficient has matched the error bands prescribed by the authors of the paper that has presented the correlations, whilst the averaged values are far beyond this band, i.e., are slightly more than 30 % higher. The further inspection has revealed a measure of similarity between the computational result of the volume fraction field distribution and the experiment, thus confirming the capability of the method to obtain realistic interface evolution in time. The method has shown full capability for further pursuing the industrial-scale film boiling problems that involve turbulent flow and the conjugate heat transfer approach.

In many developing countries, plastic waste management is left to citizens. This usually results in hazardous landfilling or open-air burning, leading to emissions that are harmful to human health and the environment. An easy, profitable, and clean method of processing and transforming the waste into value is required. In this context, this study provides an open-source methodology to transform low-density polyethylene drinking water sachets, into pavement blocks by using a streamlined do-it-yourself approach that requires only modest capital. Two different materials, sand, and ashes are evaluated as additives in plastic composites and the mechanical strength of the resulting blocks are tested for different proportion mix of plastic, sand, and ash. The best composite had an elastic modulus of 169MPa, a compressive strength of 29MPa, and a water absorptivity of 2.2%. The composite pavers can be sold at 100% profit while employing workers at 1.5X the minimum wage. In the West African region, this technology has the potential to produce 19 million pavement tiles from 28,000 tons of plastic water sachets annually in Ghana, Nigeria, and Liberia. This can contribute to waste management in the region while generating a gross revenue of 2.85 billion XOF (4.33 million USD).

There is a systematic exclusion of gender-based violence, safe abortion, reproductive cancers, infertility services, comprehensive sexuality education, sexuality services, and STI’s other than HIV in essential health packages in LMICs. To accelerate progress on sexual reproductive health (SRH), the Guttmacher–Lancet Commission proposed the adoption of these interventions into an essential health package of SRH services that should be universally available. In this commentary, we use a healthcare priority-setting processes lens to review the importance of these services for universal health coverage. We isolate inherent challenges in social value judgments for terminal, process and content evidence for their healthcare priority-setting. We then advance promising emerging practical examples from low to middle-income countries on evidence-informed decision-making processes. We recommend capacity development through regional support, generating equity and efficiency evidence and strengthening political and publicly acceptable processes to institutionalise and operationalise evidence-informed decision-making.

This paper is a mini literature review about electromagnetic field’s effects on cells, tissues and new treatment modalities. We have reviewed a papers which have been published in high quality journals in the last 5 years as two authors. This review’s aim is to be a resource for experimental studies about electricity’s effects on cell biology and pathophysiology. As a result of this literature review, we found that especially extremely low electric frequency and intermediate frequency fields have very important pathophysiological effects. We have mentioned four important expressions on this subject; electroporation, electrofusion, electrochemotherapy, gene electrotransference. Two different new treatment approaches have been developed by use of these two important electrical waves. First is tumor treating fields and the other is pulsed electric fields. Most studies in literature have been done with extremely low frequency and pulsed electric fields. In terms of diseases, most studies are about glioblastoma multiforme and malign melanoma.Most studies in literature have been done with extremely low frequency and pulsed electric fields. In terms of diseases, most studies are about glioblastoma and melanoma.

Selenium-rich Au-Ag mineralization has been discovered in the Kremnica ore district, central Slovakia. The mineralization is hosted by a single quartz-dolomite vein hosted by Neogene propyllitized andesites of the Kremnica stratovolcano. Ore mineralogy and crystal chemistry of individual ore minerals have been studied here. The early base-metal ore mineralization composed of pyrite, sphalerite and chalcopyrite lacks selenium, whereas the superimposed Au-Ag paragenesis is Se-enriched. The Au-Ag alloys, uytenbogaardtite, minerals of the galena-clausthalite series, acanthite-naumannite series, diaphorite, miargyrite, pyrargyrite-proustite, polybasite group, minerals of the tetrahedrite group and andorite branch (andorite IV, andorite VI, Ag-excess fizélyite), freislebenite, and rare Pb-Sb sulphosalts (scaiinite, robinsonite, plagionite) have been identified here. Besides selenides, the most Se-enriched phases are miargyrite, proustite-pyrargyrite, and polybasite-pearceite, whose Se contents are among the highest reported worldwide. In addition, one new phase has been found, corresponding to a Se-analogue of pearceite containing 2.08 - 3.54 apfu Se. The style of mineralization, paragenetic situation, and chemical trends observed in individual minerals are comparable to those of Au-Ag low-sulphidation epithermal Au-Ag mineralizations of the Kremnica and neighboring Štiavnica and Hodruša-Hámre Ore Districts, however, the pronounced enrichment in selenium is a specific feature of the studied vein only.