This research proposes a methodology for minimizing losses in transmission lines (LT), considering the reconfiguration of the architecture of the electrical power system (SEP). The implementation of this methodology redirects the power flow with optimal switching through its LTs to guarantee the stability of the voltage, angle, frequency, and power balance to minimize losses that affect the reliability and quality of the system. Optimal transmission switching (OTS) allows various types of analysis to be carried out, where the loadability of the lines, response times, and operating costs, among others, can be improved. This article proposes to minimize the losses in the transmission lines with the OTS by using AC power flows as a mixed integer nonlinear problem (MINLP). Several test scenarios evaluate the method’s effectiveness, determining the optimal topology for corrective control that optimizes power flows in different situations. It has been proven that this approach reduces losses compared to a base case by 99%, even in the face of N-1 or random contingencies, without losing load, maintaining the same active power dispatch, and finally verifying a strategic increase in dispatch of reactive power to maintain operating parameters within stable limits.

Wireless Powered Communication Networks (WPCN), which has attracted much attention of researchers, also been recently recommended in 5^th generation (5G) wireless networks. With the help of the WPCN, the reliability and battery life of wireless low-power devices can be improved. In this paper, we investigate throughput and ergodic capacity in WPCN-assisted amplify-and-forward (AF) relaying system, considering two transmission modes including delay-tolerant and delay-limited. As important achievement, we propose symmetric energy harvesting protocol, namely time power switching relaying (TPSR) in order to find maximal throughput. In particular, both time switching and power switching coefficients in this schemes are considered. Unlike most of the previous works, we further focus on impact of outdated channel state information (CSI) in this WPCN. In order to evaluate information processing efficiency, the performance can be substantially improved by optimally harvesting time and power coefficients of the received signal at relay node for energy and information extraction, and by deploying several scenarios. By deploying Monte Carlo simulation, it is confirmed that the system performance is more sensitive to CSI estimation error, noise variance, signal-to-noise ratio (SNR) and resulting in other reasonable computations of TPSR need be deployed to obtain QoS requirement.

The ubiquitous diffusion of Power Electronic Converters (PECs) in many fields of application including traction and energy conversion is suggesting the possibility of new and better integration of advanced power conversion and ICT services. This work investigates the possible advancements in the use of optical fibers for control of PECs, using Plastic Optical Fiber. The optical communication link connects the switching control to the converter control, following the line of separation between the expertises of the power electronic engineer and the control engineer. Control wise, the PEC becomes a black box compatible with any off-board controller, now immune from the Electromagnetic Interference (EMI) produced by the power switches. The redundant optical link is ready for the high switching (and sampling) frequencies possible with the use of SiC power semiconductor devices (100 kHz+). Distributed control of multiple PEC units and advanced telemetry for diagnostics and prognostics are targeted. A proof-of-concept demonstrator is presented and tested. Moreover, the possible evolution towards a power electronic cloud with remote management and orchestration is described.

This paper presents a new optical, multi-functional, high-resolution 3-axis sensor which serves to navigate and can, for example, replace standard joysticks in medical devices such as electric wheelchairs, surgical robots or medical diagnosis devices. A light source, e.g. a laser diode is affixed to a movable axis and projects a random geometric shape on an image sensor (CMOS or CCD). The software in the downstream microcontroller identifies the geometric shape’s center, distortion and size, then calculates X, Y, and Z coordinates. These coordinates can then be processed in attached devices. The 3-axis sensor is characterized by its very high resolution, precise reproducibility and plausibility of the coordinates produced. In addition, optical processing of the signal provides a high level of safety against electromagnetic and radio frequency interference. The sensor presented here is adaptive and can be adjusted to fit a user’s range of motion (stroke and force). This recommendation aims to optimize sensor systems such as joysticks in medical devices in terms of safety, ease of use, and adaptability.

This study evaluates the viability of n-octanol as an alternative fuel in a direct-injection diesel engine, aiming to enhance sustainability and efficiency. Experiments employed varying blends of n-octanol (10%, 30%, and 50% by volume) with pure diesel, analyzing impacts on engine performance and emissions. The methodology involved testing each blend in a single-cylinder engine, measuring engine performance parameters such as brake torque and brake power under full load conditions across an engine speed range from 1400 to 2500 rpm. Comparative assessments of performance and emission characteristics at a constant engine speed of 1700 rpm were also conducted with varying loads. Results indicated that while n-octanol blends consistently improved brake thermal efficiency, they also increased brake specific fuel consumption due to the lower energy content of n-octanol. Consequently, while all n-octanol blends reduced nitrogen oxides (NOx) emissions compared to pure diesel, they also significantly decreased carbon monoxide, hydrocarbons, and smoke opacity, presenting a comprehensive reduction in harmful emissions. However, the benefits came with nuanced trade-offs: notably, higher concentrations of n-octanol (especially the 50% blend) led to a relative increase in NOx emissions as the octanol ratio increased. The study concludes that n-octanol significantly improves engine efficiency and reduces diesel dependence, but optimizing the blend ratio is crucial to balance performance improvements with comprehensive emission reductions.

We investigate a singularly perturbed q-difference differential Cauchy problem with polynomial coefficients in complex time and space with quadratic nonlinearity. We construct local holomorphic solutions on sectors in the complex plane with respect to the perturbation parameter with values in some Banach space of formal power series in space with analytic coefficients on shrinking domains in time. Two aspects of these solutions are addressed. One feature concerns asymptotic expansions in the parameter for which a Gevrey type structure is unveiled. The other fact deals with confluence properties as q tends to 1. In particular the built up Banach valued solutions are shown to merge in norm to a fully bounded holomorphic map in all its arguments that solves a nonlinear partial differential Cauchy problem.

The electric vehicle (EV) industry is experiencing rapid growth, accompanied by continuous advancements in charging infrastructure to satisfy the rising need for fast and reliable charging. Particularly, the focus has shifted towards EV fast charging (EVFC) and its impact on the power grid. This paper presents a comprehensive analysis and survey of scholarly literature and projects conducted in this field over the past decade. The findings highlight the rising demand for EVFC and the need to address its potential adverse effects on the power grid. However, there is a noticeable lack of clear research guidance regarding charging time. To tackle these challenges and pave the way for future solutions, extensive research on DC fast charging, ultra-fast charging, and the integration of vehicle-to-grid (V2G) systems is required. This review paper thoroughly investigates the development of fast charging technology for electric vehicles (EVs), including its advantages and comparative analyses from various perspectives. Furthermore, it delves into the advancements in DC fast charging infrastructure, emphasizing charging standards and control modes. The study also investigates different categories of battery chargers for both on-board and off-board charging. Additionally, it explores the classification of DC-DC converters in the context of DC fast charging stations, discusses control strategies for EV systems, identifies existing challenges, and outlines future trends in EV fast charging.

This paper proposes training improvement methods of artificial neural networks (ANN) trajectory predictors. First, a dynamic power system time-series trajectory is split into several different segments to simplify the original ANN training problem. Moreover, the time-derivative of the trajectory is included to obtain an augmented loss function. Compared to previous studies which mainly focused on increasing the prediction accuracy, the aim of these novel techniques is to reduce the computational burden where the ANN output performance is still acceptable. The effectiveness of the developed methods is validated based on the WSCC three-machine nine-bus and IEEE 39-bus system models. The mean absolute error (MAE) and trajectory prediction results are analyzed, in which the numbers of neurons, hidden layers, and training epochs are constrained during the ANN training process. Rotor-angle difference between generators and the system frequency are investigated as the dynamic trajectories of the power system models. It is revealed that when the ANN architecture and epochs are constrained, the MAE results can be reduced, and the ANN training results can better reflect the original trajectory using the improvement approaches.

Accurate power curve modelling is essential to continuously evaluate the performance of a wind turbine (WT). In this work, we characterize the wind power curves using SCADA data acquired at a frequency of 5 minutes in a wind farm (WF) consisting of 5 WTs. Regarding the non-parametric methods, we select artificial neural networks (ANNs) to make curve estimations. Given that, we have the curves provided by the manufacturer of the WTs given by some very precisely measured pair of wind speed and power points. We can evaluate the difference between the manufacturer characterization and the ones estimated with the data provided by the SCADA system. Before the estimation, we propose a method of filtering the anomalies based on the characteristics provided by the manufacturer. We use three-quarters of the available data for curve estimation and one-quarter for the test. One WT suffered a break in the test part, so we can check how the test estimates reflect this problem in its wind-power curve compared to the estimations obtained in the WTs that worked adequately.

The article presents the results of research work devoted to improving the characteristics of paint and varnish coatings based on aqueous dispersions of polyacrylates, it is proposed to modify them by introducing mineral raw materials as fillers and hydrated lime with subsequent processing in a vortex layer apparatus. Introduction of activated diatomite does not cause deterioration of covering power, adhesion and increase of porosity of the paint material. Modification of coatings contributes to the increase of their operational properties, which can be associated with the reduction of free volume in the composite, formation of polymer boundary layers with modified physical and chemical properties. The aim of the study is to obtain water-dispersion paint and varnish composition containing modified diatomite on polyacrylate basis and subsequent study of the main physical and mechanical parameters. The work has been carried out by the following method: determination of porosity, adhesion, elasticity, covering power of the control composition; determination of porosity, adhesion, elasticity, and covering power of the obtained composites using modified filler; investigation of the influence of radiation in the infrared spectrum of the paint coating surface using FLIRB620 thermal imager. As a result of research works it was noticed that modification of water dispersions with silica activated diatomite helps to eliminate the main disadvantages of materials and coatings based on acrylate binder - low water resistance and low physical and mechanical characteristics, introduction of modified diatomite into water emulsion paint on acrylate base does not lead to deterioration of the main performance characteristics of paint coatings - porosity, adhesion, elasticity and covering.

Since general relativity (GR) has already established that matter can simultaneously have two different values of mass depending on its context, we argue that the missing mass attributed to non-baryonic dark matter (DM) actually obtains because there are two different values of mass for the baryonic matter involved. The globally obtained "dynamical mass'' of baryonic matter can be understood as a small perturbation to a background spacetime metric even though it's much larger than the locally obtained "proper mass". Having successfully fit the SCP Union2.1 SN Ia data without accelerating expansion or a cosmological constant, we employ the same ansatz to compute dynamical mass from proper mass and explain galactic rotation curves (THINGS data), the mass profiles of X-ray clusters (ROSAT and ASCA data) and the angular power spectrum of the cosmic microwave background (Planck 2015 data) without DM. We compare our fits to modified Newtonian dynamics (MOND), metric skew-tensor gravity (MSTG) and scalar-tensor-vector gravity (STVG) for each data set, respectively, since these modified gravity programs are known to generate good fits to these data. Overall, we find our fits to be comparable to those of MOND, MSTG and STVG. While this favorable comparison does not establish the validity of our proposition, it does provide confidence in using the fits to pursue an underlying action. Indeed, the functional form of our ansatz reveals an interesting structure in these fits.

The two combined technologies WPT and AI still have huge prospects for several industries such as consumer electronics and industry. This paper looks at the recent developments in WPT, particularly concerning AI-improved efficiency, range, and reliability. AI-driven also works to control power, manage device alignment, and test when maintenance is necessary, this makes powering smarter and more efficient. Accuracy is given by deploying machine learning and computer vision, and on the other hand, the maintenance procedure is done through predictions. Furthermore, the ability of the management system to include the use of AI in power regulation enables the control of consumption based on the load. In this study, the positive future effect of AI is discussed concerning improvements in WPT technologies, which is paramount in subsequent applications. Based on the results, it is essential to continue the investigation of the topic within this interdisciplinary science to advance existing problems and discover novel possibilities for evolution. Data based on experiments shows a significant improvement in the efficiency of information transfer where AI is used with rates up to 25% higher than those using the traditional ways. Additionally, advanced maintenance forecasting algorithms improve system availability by cutting down on 30% of the downtimes when applied in real-life applications of AI technology. The study also looks at the possibilities of the outlook to the future including emergence of the distributed artificial intelligence for autonomous WPT network, and additional potential of quantum computing for the use to improve the algorithm. This indicates that there is a new era for the convergence of WPT and AI to enhance the progress of power transfer system in conditions of elegant, efficient, and robust.

An important issue concerning the inspection of the technical condition of electrical power components and systems is thermal imaging investigation. This paper presents how the thermograms obtained from these measurements should be interpreted correctly according different standards and how operators should react when a specific anomaly is detected. It is also a review article in which all currently applicable international standards are referred to. The motivation of the article relates to the fact that these standards seems to be too general and not cover all practical situations even though in many countries thermal imaging diagnostics of overhead lines or overhead outdoor and indoor power stations has been used for years on the basis of industry standards or good practices. The purpose of writing this article is precisely to encourage and provoke the global community of metrologists, scientists and engineers involved in thermographic measurements to discuss, strengthen efforts and establish relevant international standards for the interpretation of thermograms containing the relevant temperature anomalies.

This article presents a buck converter in which the inductor has been replaced by a transmission line. This approach would be practically conceivable if the power supply and load have a greater spatial distance. In the time domain, this new converter can be described by a system of coupled partial and ordinary differential equations. In the frequency domain, a transcendental transfer function is obtained. For comparison with an equivalently parameterized conventional converter, Padé approximants are derived. A linear controller is designed for the converter topology under consideration.

When the distance between an obstacle and a power line is less than the discharge distance, a discharge arc can be generated, resulting in interruption of power supplies. Therefore, regular safety inspections are necessary to ensure safe operations of power grids. Tall vegetation and buildings are the key factors threatening the safe operation of extra high voltage transmission lines within a power line corridor. Manual or LiDAR based-inspections are time consuming and expensive. To make safety inspections more efficient and flexible, a low-altitude unmanned aerial vehicle remote-sensing platform equipped with optical digital camera was used to inspect power line corridors. We propose a semi-patch matching algorithm based on epipolar constraints using both correlation coefficient and the shape of its curve to extract three dimensional (3D) point clouds for a power line corridor. Virtual photography was used to transform the power line direction from approximately parallel to the epipolar line to approximately perpendicular to epipolar line to improve power line measurement accuracy. The distance between the power lines and the 3D point cloud is taken as a criterion for locating obstacles within the power line corridor automatically. Experimental results show that our proposed method is a reliable, cost effective and applicable way for practical power line inspection, and can locate obstacles within the power line corridor with measurement accuracies better than ±0.5 m.

Technological advancements must keep pace with earth’s rising demand for energy, while minimizing the carbon footprint on earth. One such option is using space based solar (SBS) radio frequency (RF) microwave power beaming. This innovative and novel technology is currently being explored to address terrestrial photovoltaic (PV) intermittency and provide a method to transmit power to other spacecraft in various orbits. This modality of power generation and distribution presents a new way to power terrestrial off-grid applications and earth orbiting spacecraft. In 1968, Dr. Peter Glaser published "Power from the Sun: Its Future", which serves as the foundation of this paper to revitalize scientific interest and efforts in this topic. This paper will primarily focus on the reliance of SBS initiatives on reusable launch vehicles (RLV) to place SBS spacecraft in a designated orbit, as well as the technological, economic, and operational challenges associated with power beaming to earth and other spacecraft. This includes a discussion of the variables from the operational environment that contribute or accelerate spacecraft end of life.

Computer systems that operate in remote locations such as satellites, remote weather stations and autonomous robots are highly limited in the availability of energy for their operation. This work aims to employ artificial intelligence algorithms in energy management in order to obtain the maximum energy yield and the prediction of energy availability to the system. The work presents the main types of algorithms used in artificial intelligence and presents the creation of a prototype that will operate as a low power system powered by batteries and a small solar plate, the prototype will perform inferences on the LSTM neural network algorithm in order to predict the future availability of energy, consequently the management system will carry out the energy distribution in order to obtain the maximum operation of the prototype without total discharge of the batteries. So that the artificial intelligence system could be embedded in the prototype, the TensorFlow Lite framework was used, which allows the inference to be carried out in devices with low consumption and limited processing power.

Recent advancements in semiconductor photonic and electronic devices such as Uni-travelling-carrier photodiodes (UTC-PDs), have played a significant role in the development of Terahertz communication technology. However, a major challenge that still persists is the limited output power from a single UTC-PD required for practical transmission distances. To enhance the output power, we propose and demonstrate a novel Terahertz wave power combining technique using a photomixer device that comprises of two arrayed UTC-PDs monolithically integrated with a microstrip line-based 2 × 1 Wilkinson power combiner and a rectangular patch antenna on a Silicon Carbide (SiC) substrate at 300 GHz. At photocurrents of 8 mA and 10 mA from the two UTC-PDs, the device experimentally exhibited a 7.3 dB increase in power relative to the power obtained with 8 mA UTC-PD and a 4.4 dB increase in power relative to the power obtained with 10 mA UTC-PD, when both UTC-PDs were irradiated. This implies that power can be enhanced by a factor of N2 if the photocurrent is multiplied by a factor of N. This technology presents a holistic and cutting edge platform for further power multiplication by further increasing the number of arrayed UTC-PDs.

A decade ago, non-radiative wireless power transmission reemerged a promising alternative to deliver electrical power to devices where a physical wiring proved to be unfeasible. However, conventional coupling-based approaches are neither scalable nor efficient when multiple devices are involved, as they are restricted by factors like coupling and external environments. Zenneck waves are excited at interfaces, like surface plasmons and have the potential to deliver electrical power to devices placed on a conducting surface. Here, we demonstrate, efficient and long range delivery of electrical power by exciting non-radiative waves over metal surfaces to multiple loads.Our modeling and simulation using Maxwells equation with proper boundary conditions shows Zenneck type behavior for the excited waves and are in excellent agreement with experimental results. In conclusion, we physically realize a radically different power transfer system, based on a wave, whose existence has been fiercely debated for over a century.

the intermittency and variability of these permeated Distributed Generators (DGs) could critically cause many security and economy risks to distribution systems. This paper applied a certain mathematical distribution to imitate the output variability and uncertainty of DGs. And then, four risk indices EENS, PLC, EFLC and SI were established to reflect the system risk level of distribution system. For the certain mathematical distribution of the DGs' output power, a developed PEM (point estimate method)-based method was proposed to calculate these four system risk indices. In this developed PEM-based method, enumeration method was used to list the states of distribution systems, an improved PEM was presented to deal with the uncertainties of DGs and the value of load curtailment in distribution systems was calculated by an optimal power flow algorithm. Finally, the effectiveness and advantages of this proposed PEM-based method for distribution system assessment were verified by the tests of a modified IEEE 30-bus system. Simulation results have shown that this proposed PEM-based method has a high computational accuracy and highly reduced computational costs compared with other risk assessment methods and is very effective for risk assessments.

The decarbonization of the electricity grid as one among the actions to reduce fossil fuel emissions, and thus their impact on global warming in the future, will be achieved mainly via the integration and widespread diffusion of renewable power sources. This is going to be supported also by the shift from the paradigm production-transmission-distribution, where electricity production oversees large-size power plants, to renewable-based distributed/diffused production, where electricity is generated very close or even by the same (group of) user(s) (or prosumers in the latter case). The number of mid-/small-size installations based on renewable energy technologies will therefore increase substantially, and the related renewable generation will be dominant against that from large-size power plants. Unfortunately, this will reduce the reliability of the grid very likely, unless appropriate countermeasures are taken/implemented, hopefully at the same time the paradigm shift is being achieved. To this aim, it is important to identify the anomalies and main fault causes that might determine in renewable-based power systems. This paper surveys the current state-of-the-art on anomalies and faults affecting wind-PV-storage hybrid power systems, i.e., the main renewable technology ensemble that will establish the future grid, and highlights possible research directions that may help to fill the literature gaps.

The critical systems, which the failure and malfunction may result in human, environment and financial severe damages, are essential components in various sectors and particularly in energy domains. Although unwished, integration error problems in supervision of critical systems occurs, incurring significant expenses because of operator’s subjective analysis and on hardware topology failures. In this work, a malleable model design approach is proposed to formulate and solve the integration error problem in the critical systems supervision in terms of reliability. A real Hybrid Power Plant (HPP) case is considered as a requirement for a study case with simulated data. A method framework with informal approach (C4 diagram) and formal approach (Hierarchical Coloured Petri Nets) in radial spectrum is applied to the HPP supervision design. Using formal methods, a formulation and solution to this problem through structured, scalable and compact mathematical representations are possible. This malleable model intends to guarantee functional correctness and then reliability of the plant supervision system based on system software architecture. Outcomes suggest corroboration that the malleable model is appropriate for energy domain, and can be used for other types of critical systems, bringing all the benefits of this methodology to the context in which it will be applied.

In this paper, new N-way Wilkinson power dividers (WPDs) are represented by using slow-wave structures such as narrow slits loaded and meandered transmission lines. The slit loaded and meandered lines are used to represent the quarter wavelength transmission lines of a conventional WPD for size reduction. Based on the proposed approaches, 2-, 4- and 8-way power dividers are designed, simulated and fabricated. The fabricated -, 4- and 8-way circuits have been measured at the center frequencies of 2.03, 1.77, and 1.73 GHz in an excellent agreement with the predicted ones. The meandered transmission lines are also used to design new types of WPDs having novel input/output port arrangements. For this purpose, two 3-way WPDs are located at both sides of the same board so as to have different power splitting ratios at different inputs and outputs to provide alternative solutions for antenna arrays. Furthermore, a 5-way dual layer WPD is introduced by locating the meandered transmission lines to two layers. The proposed 3- and 5-way WPDs allow halving the input power at the next output port in the order of P/2, P/4, P/8, P/16, and P/16. All of the designed power halving WPDs have been simulated, fabricated and successfully tested.

Modern methods of designing and constructing hydraulic pumps can no longer be imagined without the use of appropriate mathematical models, phenomena and processes that take place in concrete constructions. A mathematical model of a process represents an analytical interpretation with certain assumptions. Obtaining a mathematical model requires detailed theoretical research, based on knowledge of the laws of fundamental sciences and scientific disciplines in order to fully understand and interpret the process, based on which assumptions are adopted and model equations are defined. As mobile machines continue to evolve, so do the demands on their hydraulic systems. Efficiency, automation and other major industry trends present ongoing development opportunities for hydraulic systems used in mobile applications. Hydraulic systems remain an important component in a range of mobile applications, from construction and agricultural equipment to heavy trucks because of the power density they can provide for a range of work functions. The power density of hydraulics remains unmatched in many applications. The pump, as an essential hydraulic component, converts mechanical energy into hydraulic energy with a relatively small amount and speed of fluid.

In the development of power systems it is indicated very often, that transformation of power systems should be carried out in accordance with the idea of energy democracy. This will develop energy communities, that are trying to meet energy needs by using local renewable generation sources. This may result with a temporary low load on the MV lines connecting the community grid and the power system. Such state may cause incorrect operation of power protection systems. This can cause an extended protection operation time, due to decision algorithms inactivity at low values of measurement currents. Therefore, the detailed MV lines overcurrent digital protection model and a dynamic model of the power network were developed. The simulation results are showing that the settings of the parameters activating the protection decision algorithms affect their operation time in dynamic conditions. The conclusion is that the development of the power protection automatics must be carried out in the same time (preferably in advance) with the change of the power system operation model. This is very important for future power systems with high penetration energy communities and renewable generation sources.

(1) Background: Conventional strength training and core exercises are commonly prescribed to improve cycling performance. Although previous studies have explored the utility of strength training in various cycling populations, this intervention has never been compared to core exercises; (2) Methods: 36 trained road cyclists were divided in 3 groups of 12 participants that performed either no strength training, conventional strength training or core exercises, in all cases together with their regular cycling training during a 12-week period. Peak power outputs across different durations (5 seconds, 60 seconds, 5 minutes, and 20 minutes) were recorded before and after the intervention; (3) Results: Conventional strength training is superior to core training and no strength training for all measured durations. At the same time, core training results in improved 5 second power output when compared to no strength training, while all the other measures are comparable among groups; (4) Conclusions: Conventional strength training is superior to core exercises and no strength training in trained road cyclists, and accordingly, it is recommended that this population incorporates strength training during their regular weekly workouts.

Partial shading on solar photovoltaic (PV) arrays is a prevalent problem in photovoltaic systems that impair the performance of PV modules and is responsible for reduced power output as compared to that in standard irradiance conditions thereby resulting in the appearance of multiple maximas on panel output power characteristics. These maxims contribute to mismatch power losses among PV modules. The mismatch losses depend on shading characteristics together with different interconnected configuration schemes of PV modules. The research presents a comparative analysis of partial shading effects on a 4 x4 PV array system connected in series(S), parallel (P), serries-parallel (SP),total-cross-tied (TCT),central-cross-tied(CCT),bridge-linked(BL),bridge-linked total cross-tied (BLTCT) ,honey-comb(HC), honey-comb total-cross-tied (HCTCT) and ladder (LD) configurations using MATLAB/Simulink. The PV module SPR-X20-250-BLK was used for modeling and simulation analysis. Each module is comprised of 72 number of PV cells and a combination of 16 PV modules was employed for the contextual analysis. Accurate mathematical modeling for the HCTCT configuration under partial shading conditions (PSCs) is provided for the first time and is verified from the simulation. The different configuration schemes were investigated under short-narrow,short-wide,long-narrow,long-wide, diagonal, entire row distribution, and entire column distribution partial shading condition patterns with mathematical implementation and simulation of passing clouds. The performance of array configurations is compared in terms of maximum power generated ), mismatch power loss (∆), relative power loss ) and the fill factor (FF). It was inferred that on average, TCT configuration yielded maximum power generation under all shading patterns among all PV modules interconnection configurations with minimum mismatch power losses followed by hybrid and conventional PV array configurations respectively.

Humanity is shifting its power generation to renewable energy, notably wind power. As more and more wind power plants are built, it has become important to improve the efficiency of wind power generation and reduce the manufacturing costs of wind power equipment. The mechanical multiplier gearbox is one of the most important parts of the wind power turbine, and it is now being built as a planetary gear train as these gearboxes offer a compact build capable of high power ratings in a relatively small package with coaxial input and output shafts. It is very important to select the right kinematic scheme and the other relevant parameters in the early design stages as the wrong kinematic scheme will result in a suboptimal solution. This article deals with the selection of the optimal gearbox solution for a 700 kW wind turbine application, taking into account both two-carrier and three-carrier gearbox solutions. As the optimal solution may be deducted only by systematic analysis, the proprietary 2-SPEED software has been developed for this purpose. The results of the analysis have been presented in this article, and optimal gear train solutions have been suggested for both two-carrier and three-carrier multiplier configurations.

Electric tractors have many advantages, including high torque, excellent controllability, energy efficiency, simple structure, and electric interface for expansion. However, a significant limitation lies in their endurance. This study presents the design of an extended-range power supply system to ensure continuous endurance of electric tractor. The objective is to provide a continuous power source for our self-developed electric tractor while preserving the benefits of electric propulsion. Extended-range power systems utilize a primary mover, typically an oil-fueled internal combustion engine, to drive the generator for electricity generation, and the generated AC form electricity is subsequently converted into stable DC bus voltage by a power electronic converter. The hardware and control design of the extended-range power supply system have been finalized and validated through experimental trials. Results demonstrate the system’s capability to sustain a stable DC bus voltage amidst disruptions such as sudden load shifts and fluctuations in prime mover speed. Even with 50% sudden load change, the voltage drop is within 12% and could recover to ±3% within 4 seconds. The range extender can be used alone without battery to power the electric tractor, or it can used in parallel with other extended-range extenders or battery thanks with the droop control ability for power sharing.

This paper experimentally reveals some of the resources offered by the evolution of the instantaneous active electric power in describing the state of three-phase AC induction asynchronous electric motors (with squirrel-cage rotor) operating under no-load conditions. A mechanical power is required to rotate the rotor at no-load and this mechanical power is satisfactorily reflected in the constant and variable part of instantaneous active electric power. The variable part of this electrical power should necessarily have a periodic component with the same period as the period of rotation of the rotor. The paper proposes a procedure for extracting this periodic component description (as a pattern, by means of a selective averaging of instantaneous active electrical power) and analysis. The time origin of this pattern is defined by the time of a selected first passage through the origin of an angular marker placed on the rotor, detectable by a proximity sensor (e.g. a laser sensor). The usefulness of the pattern in describing the state of the motor rotor has been demonstrated by several simple experiments which show that a slight change in the no-load running conditions of the motor (e.g. by placing a dynamically unbalanced mass on the rotor) has clear effects in changing the shape of the pattern.

A layout of urban waste fired zero emission power plant is described in this paper. The principle of layout, which comes from similar coal-fired plants retrieved from the literature, integrates gasification with a power generation section, and implements two parallel conversion processes, one supplied by the heat of the gasifier consisting of a thermoacousticmagnetohydrodynamic (TAMHD) generator, while in the second one the syngas is treated in order to obtain almost pure hydrogen, which is fed to fuel cells. The CO2 deriving from the oxidation of Carbon base is stocked in liquid form. The novelty of the proposed layout lies in the fact that the entire conversion is performed without solid moving parts. The resulting plant avoids any type of emissions in the atmosphere, increases mechanical efficiency as compared to traditional plants, thanks to the absence of moving parts, nonetheless, resolving at its root the ever-increasing waste-related pollution problems.

To quantitatively estimate the risk of power system operation under extreme rainfall, a multi-scenario stochastic risk assessment method is proposed. First, a scenario generation scheme considering waterlogged faults of power facilities is constructed based on the storm water management model (SWMM) and the extreme learning machine method. These scenarios will be merged to several typical scenario sets for further processing. The outage of power facilities will induce power flow transfer which may consequently lead to transmission lines’ thermal limit violation. Semi-invariant and Gram-Charlier level expansion methods are adopted to analytically depict the probability density function and cumulative probability function of each line’s power flow. The optimal solution is performed by a particle swarm algorithm to obtain proper load curtailment at each bus, and consequently the violation probability of line thermal violations can be controlled within an allowable range. The volume of load curtailment as well as their importance are considered to quantitatively access the risk of power supply security under extreme precipitation scenarios. The effectiveness of the proposed method is verified in case studies based on the IEEE 24-bus system.

Harmonic resonances are part of the Power Quality (PQ) problems of electrified railways and have serious consequences for the continuity of service and integrity of components in terms of overvoltage stress. The interaction between Traction Power Stations (TPSs) and trains that causes line resonances is briefly reviewed showing the dependence on infrastructure conditions. The objective is real-time monitoring of resonance conditions seen first of all from the onboard panto-graph interface, but it is equally applicable at TPS terminals. Voltage and current spectra, and de-rived impedance and power spectra, are analyzed proposing compact and efficient methods based on Short-Time Fourier Transform, suitable for real-time implementation with the hardware avail-able for energy metering and harmonic interference monitoring. The methods are tested by sweeping long recordings taken at some European railways, covering cases of longer and shorter supply sections, with a range of resonance frequencies of about one decade. They give insight into the spectral behavior of resonances, their dependency on position and change over time, and criteria to recognize genuine infrastructure resonances from rolling stock emissions.

This paper proposes a method based on genetic algorithm (GA) for the security-constrained optimal dispatch of integrated natural gas and electricity networks, considering operating scenarios in both energy systems. The mathematical formulation of the optimization problem consists of a multi-objective function which aims to minimize both cost of thermal generation (diesel and natural gas) as well as the production and transportation of natural gas. The joint gas-electricity system is modeled by two separate groups of nonlinear equation, which are solved by the combination of Newton's method with the GA. The applicability of the proposed method is tested in the Belgian gas network integrated with the IEEE 14-bus test system and a 15-node natural gas network integrated with the IEEE 118-bus test system. The results demonstrate that the proposed method provides efficient and secure solutions for different operating scenarios in both energy systems.

When a grid-forming (GFM) inverter is connected to a low or medium voltage weak power grid, the line impedance with resistive-inductive characteristics will cause power coupling. Typical GFM decoupling control strategies are designed under nominal line impedance parameters. However, there are deviations between the nominal line impedance and actual parameters, resulting in poor decoupling effects. Aiming at this problem, this paper proposes a power decoupling strategy based on a reduced-order extended state observer (ESO). Firstly, the power dynamic model of GFM is established based on the dynamic phasor method. Then, the model deviation and power coupling due to line impedance parameter perturbation are estimated as internal disturbances of the system, and the disturbances are compensated on the basis of typical power control strategy and virtual impedance decoupling. Good decoupling performance is obtained under different impedance parameters, improving the control strategy's robustness. Finally, the effectiveness of the proposed method is verified by the results of RT Box hardware-in-the-loop experiments.

This paper discusses recent developments in creep, over a wide range of temperature, that mqy change our understanding of creep. The five-power law creep exponent (3.5 to 7) has never been explained in fundamental terms. The best the scientific community has done is to develop a natural three power-law creep equation that falls short of rationalizing the higher stress exponents that are typically five. This inability has persisted for many decades. Computational work examining the stress-dependence of the climb rate of edge dislocations we may rationalize the phenomenological creep equations. Harper-Dorn creep, “discovered” over 60 years ago has been immersed in controversy. Some investigators have insisted that a stress exponent of one is reasonable. Others believe that the observation of a stress exponent of one is a consequence of dislocation network frustration. Others believe the stress exponent is artificial due to the inclusion of restoration mechanisms such as dynamic recrystallization or grain growth that is not of any consequence in the five power-law regime. Also, the experiments in the Harper-Dorn regime, which accumulate strain very slowly (sometimes over a year) may not have attained a true steady state. New theories suggest that absence or presence of Harper-Dorn may be a consequence of the initial dislocation density. Novel experimental work suggests that power-law breakdown may be a consequence of a supersaturation of vacancies which increase self-diffusion.

In this paper a variable’s involved in assessing the quality of a distributed generation system are reviewed, aiming to minimize the electric power losses (unused power consumption) and optimize the voltage profile. To provide this assessment, several experiments have been made to the IEEE 34-bus test case and various actual test cases with the respect of multiple DG units. The possibility and effectiveness of the proposed algorithm for optimal placement and sizing of DG in distribution systems have been verified. Finally, four algorithms were trailed: simulated annealing (SA), hybrid genetic algorithm (HGA), genetic algorithm (GA) and variable neighbourhood search. The HGA algorithm was found to produce the best solution at a cost of longer processing time.

This investigation is part of a topical situation where wireless equipment is gradually being used for energy transfer, particularly for autonomous systems and the use of decarbonized en-ergies. A characteristic example of decarbonized autonomous use is linked to the substitution of thermal engine vehicles by electric vehicles (EVs) equipped with energy storage batteries. This response was considered in an ecological context of reducing air pollution and defending plane-tary biodiversity, which are currently vital. These EVs ultimately operate thanks to the wireless charging of their batteries when stationary or running. By changing long-established means of transport that have become a threat to biodiversity, it is necessary to ensure that innovative re-placement solutions protect this biodiversity. In addition, the construction of wireless power transfer (WPT) battery chargers for these EVs must offer an optimal ecology of clean energy saving. In such a context, the two concepts of One Health (OH) and Responsible Attitude (RA) will find their place in the design and control of WPT tools in EVs. This contribution aims to il-lustrate and analyze the roles of the green and non-wasteful OH and RA approaches in the de-sign and control of WPT embedded in EVs for the smart city (SC) environment. In the paper, WPT tools are first introduced. The design and control of EV battery charging tools are then examined. The biological effects on living tissues due to the electromagnetic field (EMF) radia-tion of WPT are analyzed. The phenomena and equations governing the design of WPT and the effects of EMF radiation are then exposed. The OH and RA approaches in the SC context are af-terward analyzed. The protection against the unsafe effects of WPT tools in the SC environment is consequently explored. The analyses followed in the paper are supported by examples of lit-erature.

The efficiency of organic solar cells (OSCs) is influenced by various factors, among which environmental temperature plays a significant role. Previous studies have shown that the thermal stability of these cells can be enhanced by incorporating a third component into their structure. Ternary organic solar cells, in particular, have shown promising results in improving thermal stability. A well-designed electron transport layer (ETL) can significantly bolster thermal stability by facilitating efficient charge transport and reducing charge recombination. In this study, we investigated the effect of temperature on the efficiency of inverted ternary structures, ranging from 300 K to 400 K. The structures examined include FTO/SnO2/PM6:D18:L8-BO/PEDOT: PSS/Ag, FTO/Spiro-OMeTAD/PM6:D18:L8-BO/PEDOT: PSS/Ag, and FTO/PC60BM/PM6:D18:L8-BO/PEDOT: PSS/Ag. Through simulations employing three different electron transport layers—SnO2, Spiro-OMeTAD, and PC60BM—we observed that at 340 K (65°C) these structures maintained 92% of their original high efficiency of ~20% at 300 K, which represents a high level of thermal stability under the high PCE condition.

This study profiled morphological and laboratory-derived performance biomechanics by position of American style football players training for the National Football League draft. Fifty-five players were categorized into Big (e.g., lineman; n=17), Big-skill (e.g., tight end; n=11), and Skill (e.g., receiver; n=27) groups. Body fat (BF%), lean body mass (LBM), total body mass, running force and ground contact time (GCT), countermovement jump height (CMJ-JH), CMJ normalized peak power (CMJ-NPP), and reactive strength were measured in a laboratory. Asymmetry was calculated for running force, GCT, and CMJ eccentric and concentric impulse (IMP). MANOVA determined between-group differences, and radar plots for morphological and performance characteristics were created using Z-scores. There was a significant between-group difference, F(26,80)=5.70, p<0.001;Wilk’s Λ=0.123, partial η2=0.649. Fisher’s least squares difference post-hocs showed Skill had greater JH, CMJ-NPP, reactive strength, and running force versus Big but not Big-skill, p<0.05. Big had greater BF%, LBM, total body mass, and GCT than Skill and Big-Skill, p<0.05. Big-skill had greater GCT asymmetry than Skill and Big, p<0.05. Asymmetries in running forces, and CMJ eccentric and concentric IMP were not different, p>0.05. Morphological and performance biomechanics differences are pronounced between Skill and Big. Big-skill possess characteristics from both groups. Laboratory-derived results provide specialized profiles of draft trainees.

The current globally dominant SARS-CoV-2 variants are showing immune escape and reduced susceptibility to antiviral drugs. Therefore, agencies responsible for drug evaluation and regulation such as the FDA and EMA are revising their emergency authorization use of several COVID-19 neutralizing antibodies. These MAbs proved to be unlikely effective against new variants especially Omicron descendants and several pharmaceutical companies are pursuing the development of more potent neutralizing antibodies. To address this issue, we used In Silico method we previously developed to assess 10 anti-SARS-CoV-2 antibodies propensity to neutralize the new Omicron’s subvariants EG.5, BA.2.86 and JN.1, based on comparative binding affinity of 3D generated models and previous experimental and clinical observations. Nine of these MAbs were once granted emergency use authorization, and one is currently under clinical investigation. The results showed that one antibody showed a marked increase of the binding energy for EG.5 compared to two antibodies that showed a significant increase with Pirola (BA.2.86) and JN.1. This data indicates that the new SARS-CoV-2 variant escapes neutralization of most of the available therapeutic NAbs. Furthermore, the data showed new potential therapeutic MAbs combination that could be effective for the treatment countermeasure of the new Omicron’s descendants or potential novel variants.

Railway has been used as one of the most crucial means of transportation in public mobility and economic development. For efficiently operating railways, the electrification system in railway infrastructure, which supplies electric power to trains, is essential facilities for stable train operation. Due to its important role, the electrification system needs to be rigorously and regularly inspected and managed. This paper presents a supervised learning method to classify Mobile Laser Scanning (MLS) data into ten target classes representing overhead wires, movable brackets and poles, which are recognized key objects in the electrification system. In general, the layout of railway electrification system shows a strong regularity of spatial relations among object classes. The proposed classifier is developed based on Conditional Random Field (CRF), which characterizes not only labeling homogeneity at short range, but also the layout compatibility between different object classes at long range in the probabilistic graphical model. This multi-range CRF model consists of a unary term and three pairwise contextual terms. In order to gain computational efficiency, MLS point clouds is converted into a set of line segments where the labeling process is applied. Support Vector Machine (SVM) is used as a local classifier considering only node features for producing the unary potentials of CRF model. As the short-range pairwise contextual term, Potts model is applied to enforce a local smoothness in short-range graph. While, long-range pairwise potentials are designed to enhance spatial regularities of both horizontal and vertical layouts among railway objects. We formulate two long-range pairwise potentials as the log posterior probability obtained by Naïve Bayes classifier. The directional layout compatibilities are characterized in probability look-up tables which represent co-occurrence rate of spatial relations in horizontal and vertical directions. The likelihood function is formulated by multivariate Gaussian distributions. In the proposed multi-range CRF model, the weight parameters to balance four sub-terms are estimated by applying the Stochastic Gradient Descent (SGD). The results show that the proposed multi-range CRF can effectively classify detailed railway elements, representing the average recall of 97.66% and the average precision of 97.07% for all classes.

The inherent capabilities of the K-means++ algorithm to approximate system dynamics within complex systems are subjected by constructing a network structure that captures interconnections among identified components, extending its original purpose as a data clustering method and transforming it into a tool for systems analysis. Leveraging advanced measurement technologies and sophisticated data collection systems, the K-means++ algorithm unveils hidden relationships among components and identifies critical elements. This study explored the algorithm's potential, facilitating the identification of critical components to enhance system operation, control, optimization, and decision-making and examining the practicality and resiliency of the method in real-world application with noisy and limited data. A case study conducted on power systems (IEEE 39-bus and IEEE 300-bus systems) exemplifies K-means++'s capacity to accurately identify critical components and approximate system dynamics, supported by performance metrics affirming its effectiveness and robustness in system analysis through measurements of bus similarity within clusters based on standard deviation and comparison of net tie-line flows in equivalent networks with the original network across scenarios. Performance metrics, including the Silhouette Score, Davies-Bouldin Index, and Variation of Information (VI) score, further validated K-means++'s performance, yielding reliable and consistent results.

Dynamic wireless charging (DWC) for electric vehicles (EVs) is gaining traction as a more accessible charging method, with the added benefits of extending vehicle range and reducing battery size. By providing a charging connection through the road surface, DWC offers an additional charging option without the need for a physical connection. This approach inherently links the charging load profile to the vehicle's movement relative to the charging pad(s), thus introducing more stochastic charging events to the grid. For dynamic wireless power transfer (DWPT), these events involve high instantaneous power and are short in duration. To better understand the impact of DWPT, accurate models are required to test control systems and potential solutions. Additionally, these systems require high-frequency simulation for wireless power transfer (WPT), which results in long simulation times during development. In this paper, a simplified model is presented to ensure the efficiency of grid-connected simulations and achieve a certain level of accuracy that reflects the internal dynamics of wireless charging. This model achieves a 30-fold reduction in simulation time with only a 6% deviation from the base model.

Building a new-type power system is the key core of the green and low-carbon development of energy, the restructuring of the power system will inevitably have a linked impact on the coordinated development of the economy-energy-environment (3E) system. This paper constructs a "Dual-Triangle" theoretical framework consisting of the “Energy Trilemma” and the "Sustainable Development Triangle", by combining historical statistical analysis with scenario predictive analysis, analyzes the historical characteristics of the "Dual Triangle" and future development trends under different scenarios, and studies the coupled interaction relationship of the "Dual-Triangle" to explore the optimal transformation path of the power system that is most beneficial to the coordinated development of the 3E system. The conclusions are as follows: (1) The energy system gradually inclined towards economy and cleanliness from 2010 to 2022, the level of coordinated development of the 3E system fluctuated upwards, and the operation status of the "Dual Triangle" was stable. (2) Positive coupling relationship between "Dual Triangle" of scenario S1 is close, which can be regarded as the preferred path for the reconstruction of the power system. Due to phased development has clear development priorities, scenario S2 will artificially break the balance of the “Energy Trilemma”, which is a development model that dynamically mitigates the challenges of the “Energy Trilemma”.(3)The contradiction between economy and cleanliness is continuously weakened, and security has become the core contradiction of the "Impossible Triangle". The combination of renewable energy and energy storage is the key to resolving this contradiction. This paper conducts an integrated and innovative application of the "Dual-Triangle" theory, and the results provide a case basis for how to achieve the coupled interaction of the "Dual-Triangle", promote high-quality energy development, and support the sustainable development of the economy and society.

The analysis of the key factors which prevent or contribute to the promotion and development of the Power Purchase Agreements (PPAs) in order to meet the sustainability goals represents an important issue which worth being investigated, especially in the situation in which entering in bilateral relations inside this contract has a powerful meaning in achieving new climate targets, developing and improving the use of green energy, and promoting a sustainable green economy. The main goal of this research is to identify and analyze the main factors which help or pre-vent the promotion and development of a PPA, in order to meet the sustainability goals by promoting a green economy. For this research survey based on comparative analysis, questionnaires and interviews with energy experts, Spearman’s correlation matrix and IBM SPSS Statistics for Window are also used. The results suggest that although there are positive interest and an open attitude towards the PPA from both sides (sellers and buyers), but there is still place for improvement, the lack of knowledge or the insufficient measures taken so far being two of the reasons way until now in Romania we do not have a developed PPA market and the level of knowledge regarding this type of mechanism is quite low.

The Active Distribution Networks (ADNs) are Multi-Input Multi-Output (MIMO) systems with coupled dynamics which cause interactions among the control loops of the Distributed Energy Resources (DERs). This undesired effect lead to performance degradation in the voltage control. To mitigate the effects of these unavoidable coupling, the present paper proposes a systematic design procedure based on the analysis of the interaction's sources. In details, each DER is equipped with a double loop PI to control the active and reactive powers output by the Voltage Source Converter (VSC) which connects the DER to the network's node. Furthermore, to guarantee Ancillary Services (ASs), the two loops are coupled by a simple mechanism of cooperation of the active power to voltage regulation realized by a filtered droop law. To achieve voltage regulation with reduced loop interactions, the PI parameters and the filter's pulse are designed according to a two sequential steps procedure based on the (Internal Model Control) IMC technique. Simulation studies are finally presented to demonstrate that the proposed design method achieves both reduction of the loop interaction and robust voltage control in presence of model parameter uncertainty in the MIMO model.

This paper designed a new type of generator, transgenerator, that integrates the wind turbine and flywheel into one system, aiming to make the flywheel distributed energy storage (FDES) more modular and scalable than the conventional FDES. The transgenerator is a three-member dual-mechanical-port (DMP) machine with two rotating members (inner and outer rotors) and one stationary member (stator). The transgenerator-flywheel system is introduced with the system configuration, transgenerator overview, flywheel operation principle and power management strategies, and control system. Simulations are performed in MATLAB/ Simulink to verify the system viability, including control system verification and the flywheel storage performance evaluation. Results show that the inner and outer rotors can be controlled independently with accurate and fast control response, and the grid-side control works properly. The flywheel performs well with considerable charging power and storage capacity.

The energy transition towards renewable and more decentral power production triggers the need for grid and storage expansion on all voltage levels. Today's power system planning focuses on certain voltage levels or spatial resolutions. In this work we present an open source software tool eGo which is able to optimize grid and storage expansion throughout all voltage levels in a developed top-down approach. System costs are minimized by applying a linear optimal power flow considering the grid infrastructure of the extra-high and high-voltage (380 to 110 kV) level. Hence, the common differentiation of transmission and distribution grid is partly dissolved, integrating the high-voltage level into the optimization problem. Consecutively, optimized curtailment and storage units are allocated in the medium voltage grid in order to lower medium and low voltage grid expansion needs, that are consequently determined. Here, heuristic optimization methods using the non-linear power flow were developed. Applying the tool on future scenarios we derived cost-efficient grid and storage expansion for all voltage levels in Germany. Due to the integrated approach storage expansion and curtailment can significantly lower grid expansion costs in medium and low voltage grids and at the same time serve the optimal functioning of the overall system. Nevertheless, the cost-reducing effect for the whole of Germany was marginal. Instead, the consideration of realistic, spatially differentiated time series lead to substantial overall savings.

An energy production system consisting solar collector, biogas dry reforming reactor and solid oxide fuel cell (SOFC) was assumed to be installed in Kolkata, India. This study aims to understand the impact of climate condition on the performance of solar collectors with different lengths of parabolic trough solar collector (dx) and mass flow rate of heat transfer fluid (m). In addition, this study has evaluated the amount of H2 produced by biogas dry reforming (GH2), the amount of power generated by SOFC (PSOFC) and the maximum possible households (N) whose electricity demand could be met by the energy system proposed, considering the performance of solar collector with the different dx and m. As a result, the optimum dx was found to be 4 m. This study revealed that temperature of heat transfer fluid (Tfb) decreased with the increase in m. Tfb in March, April and May was higher than that in other months, while Tfb from June to December was the lowest. GH2, PSOFC and N in March, April and May were higher than that in other months irrespective of m. The optimum m was 0.030 kg/s.

Relevant observations suggest that in geothermal power resources and volcanic regions in Earth the mean heat flow is either comparable or greater than the current global mean heat flow of this planet. We have inferred that critical or minimum heat flow required to sustain geothermal provinces (T >150⁰C) is at least 90 mWm^-2 and the same required to sustain active volcanoes in Earth is at least 100 mWm^-2.The volcanism in Venus is found have declined significantly during the past 300 Ma. It is suggested that Earth may lose significant part of its current active volcanoes and geothermal power resources in the next 300-500 Ma if the global mean heat flow in Earth is decreasing at a rate of 5.76 mW per 100 Ma. At the current inferred maximum rate of mantle cooling (20^o C per 100 Myrs) the plate tectonics in Earth is likely to cease within 750 Myrs from now. The critical mean surface heat flux for sustaining plate tectonics in Earth is inferred to be around 50-55 mW/m².

Power semiconductor devices are essential from the operation point of view, size, efficiency and cost, these components are used in a myriad of applications, providing features that make them an important part of the system in which they are operating. This document analyzes and compares the basic structure, properties, design aspects, as well as temperature performance, stability and switching losses, present in devices on silicon (Si), silicon carbide (SiC) and new generation devices fabricated in gallium nitride (GaN) applied in renewable energy systems. The main objective is determinate the viability of the new generation components, which present a superior performance in view of an increase in efficiency, conductivity, decreases in switching losses, lower resistances and parasitic capacitances as well as higher operating frequency range. Therefore demonstrating the GaN components are a strong and viable candidate to solve some of the problems present in renewable energy systems.

Optical power splitters play a crucial role as the fundamental building blocks for many integrated optical devices. They should have low losses, broad bandwidth, and a high tolerance to fabrication errors. Adiabatic optical power splitters inherently possess these qualities while being compatible with foundry processes well-suited for mass-production. The long device lengths of adiabatic power splitters, however, are a limiting factor to achieve compact device sizes, which must be reduced. Here, we use a polynomial taper profile optimization algorithm to design 1×2 and 2×2 adiabatic power splitters with significantly shorter lengths than their adiabatic counterparts. The best performing 1×2 and 2×2 power splitters have 20 μm and 16 μm coupling lengths, respectively. Our designs have minimum feature sizes ranging from 140 nm to 200 nm, and our measurements averaged across 9 different chips show excellent consistency in performance for devices with 180 nm and 200 nm minimum features. Both the 1×2 and 2×2 adiabatic optical power splitters have excess losses less than 0.7 dB over a 100 nm bandwidth, with a standard deviation lower than 0.3 dB. Furthermore, our measurements show greater than 20 dB extinction ratios over 130 nm bandwidth. We also demonstrate the design of 1×2 power splitters with arbitrary splitting ratios, where splitting ratios ranging from 50:50 to 94:6 were achieved with standard deviations between 2% and 6%.

This study presents a cost-effective IoT-based remote monitoring system for solar PV energy systems, along with a machine learning-based PV power estimator. Remote access is crucial for tracking PV systems installed in remote areas. In this system, an open-source and IoT-compatible data logger is employed. The data logger collects important performance data of the PV system and transfers it to a server. Real-time visualization of this data is displayed in the designed web and mobile monitoring interfaces. The measured data includes the current, voltage, and temperature information of the PV generator and battery, as well as environmental parameters such as temperature, radiation, humidity, and pressure. Subsequently, this data is used for PV power estimation using machine learning methods. This enables the identification of maintenance requirements and the prediction of potential issues in the PV system. When a problem occurs in the PV system, the user is alerted through the mobile application. Early detection and intervention prevent power loss and damage to system components. When comparing the results of linear regression, SVM, decision trees, random forests, and KNN machine learning methods for power estimation based on performance evaluation criteria, it was observed that the random forests algorithm provided the best results. In conclusion, the developed monitoring and estimation system, along with web and mobile interfaces, is suitable for large-scale PV energy systems.

Proper management of solar energy, as an effective renewable source, is of high importance toward sustainable energy harvesting. This paper offers a novel sophisticated method for predicting solar irradiance (SIr) from environmental conditions. To this end, an efficient metaheuristic technique, namely electromagnetic field optimization (EFO) is employed for optimizing a neural network. This algorithm quickly mines a publicly available dataset for non-linearly tuning the network parameters. To suggest an optimal configuration, five influential parameters of the EFO (i.e., N_Pop, R_rate, Ps_rate, P_field, and N_field) are optimized by an extensive trial and error practice. Analyzing the results showed that the proposed model can learn the SIr pattern and predict it for unseen conditions with high accuracy. Furthermore, it provided about 10% and 16% higher accuracy compared to two benchmark optimizers, namely shuffled complex evolution and shuffled frog leaping algorithm. Hence, the EFO-supervised neural network can be a promising tool for the early prediction of SIr in practice. The findings of this research may shed light on the use of advanced intelligent models for efficient energy development.

In most studies reported in literature, a flat, constant coefficient is used to convert the amount of optical power required at the input of an optical link into the effective power consumption. This constant coefficient approach is very simple to apply but not accurate, since laser efficiencies are dependent on the optical output power in addition to the operating temperature. In this paper the relationship between laser wall plug efficiency and optical power output is investigated and the effect of this variance on optical links and on-chip laser source electric power consumption is presented

The use of optical fibers is increasing in modern aircraft because it helps solve challenges of size, weight, communication, and reliability in new aircraft generation. This work describes a video and power transmission system using optical fibers (PoF) for in-flight entertainment (IFE) system application. We present the benefits and the limitations of this application, and we perform two practical experiments to demonstrate their performance. It used off-the-shelf devices in the experiments, such as one 15-W semiconductor laser operating at 808 nm, GaAs photovoltaic converters, optical transmitters and receivers, and video monitors. The power and video signals were transmitted using two 50-m multimode fibers. In addition, we proposed and tested two types of energy transformation units (ETU), which are responsible for supplying electrical energy to the IFE video monitor and the optical fiber receiver.

The overrun of transient power quality index caused by the large-capacity electric arc furnace (EAF) has become a prominent problem affecting the safe and stable operation of the power system. (1) In this paper, the relationship between arc furnace volt-age and current is derived based on the different stages of arc combustion, and the random variation of chaotic phenomenon of the arc voltage are simulated. Established an EAF model suitable for the study of transient power quality problems. (2) Take 50t AC EAF as an example to analyze the reactive power impact and the influence on the point of common coupling (PCC) voltage caused by the three-phase short circuit of the electrode. The results show that the experimental results are consistent with the theoretical analysis, verifying the correctness and effectiveness of the model. (3) When the three-phase short-circuit occurs, the reactive power impact is nearly 6 times that of normal operation, the short-circuit current is 2.66 times that of normal operation, and the effective value of the PCC voltage has dropped by 40.37%, which provides a theoretical basis for real-time compensation of impulsive reactive power and improvement of the transient power quality of the EAF.

Mobile robots can perform tasks on the move, including exploring terrain, discovering landmark features or moving a load from one place to another. This group of robots is characterized by a certain level of intelligence allowing making decisions and responding to stimuli received from the environment. As part of Industry 5.0, such mobile robots and humans are expected to co-exist and work together in a shared environment to make human work less tiring, quicker, and safer. This can only be realized when clean, dense, and economical energy sources are available. The aim of the study is to analyze the state of the art and to identify the most important directions for future developments in robotic power systems based mainly on batteries. The efficiency and performance of the battery depends on the design using different materials. Work environments and performance requirements are considered in this systematic review to classify solutions that help developers choose the best suited power system for specific application. Indirectly, the aim of the work is to generate discussion within the scientific and engineering community. A narrative review of publications from six major bibliographic databases according to preset inclusion criteria was combined with a critical analysis of current and future technologies. The main findings of the review allow answering question what is the role of modern power source technologies, artificial intelligence and ground-breaking research work in global policies related to energy saving, green policies, and sustainable development. The main opportunities and threats are discussed, and a brief feasibility analysis is carried out. Novelty of the article relates not only to the analysis of technologies, but also to approaches and their use under conditions of limited resource availability, when resource usage must be minimized. The article provides an overview of batteries, their specifications, classifications, and their advantages and disadvantages. In addition, we propose: (1) an algorithm for selecting main energy source for robot application, and (2) an algorithm for selecting electrical system power supply. Current mobile robot batteries are, in most cases, their biggest limitation. Progress in batteries development is too slow to catch up with the demand for robot autonomy and range requirements, limiting the development of mobile robots. Further intensive research and implementation work is needed to avoid years of delay in this area.

Micro plasma devices (MPD) with power gains are of interest in applications involving operations in the presence of ionizing radiations, in propulsion, in control, amplification of high power electromagnetic waves, and in metamaterials for energy management. Here we review and discuss MPDs with an emphasis on new architectures that have evolved during the past 7 years. Devices with programmable impact ionization rates and programmable boundaries are developed to control the plasma ignition voltage and current to achieve power gain. Plasma devices with 1-10 μm gaps are shown to operate in the sub-Paschen regime in atmospheric pressures where ion-assisted field emission results in a breakdown voltage that linearly depends on the gap distance in contrast to the exponential dependence dictated by the Paschen curve. Small gap devices offer higher operation frequencies at low operation voltages with applications in metamaterial skins for energy management and in harsh environment inside nuclear reactors and in space. In addition to analog plasma devices, logic gates, digital circuits, and distributed amplifiers are also discussed.

Wireless communications are gaining massive demand for faster video streaming, virtual reality, and 5G-based IoT (Internet of Things) applications. Due to this network congestion increases hastily. The demand for user-specific services, machine learning, forcing the radio access network (RAN) to provide improvement in utilization of spectrum efficiency, minimizing power consumption, and improving data rate. For LTE/LTE-A network specifications provided by third-generation partnership project (3GPP), guarantees to provide qualitative of service (QoS). Release 15/16 utilizes two-dimensional (2D) active antenna array systems (AAS). This kind of AAS provides beam forming in both azimuth and elevation also termed as Full Dimensional MIMO (FD-MIMO). It enhances the radiation pattern of the antenna array element by adjusting the angular power spectra at the base station (BS), it also allows selecting the minimum number of antennas for effective beam forming toward specific user equipment’s (UEs). Spectrum allocation challenge can be dealt with at mm wave band having FR2 (>6GHz) frequency band specified by International Telecommunication Union (ITU-R) in line with IMT-2020 specifications. The spectrum is free at mm Wave for communication of 5G. However, the main challenge is, it faces path loss and atmospheric loss electromagnetic energy absorbed by gases like oxygen. In this work, the 5G new RAN power spectrum and power delay profile at 10GHz carrier frequency with 20MHz to 100MHz channel bandwidth is observed for line of sight (LOS) and non-line of sight (NLOS) communication for guaranteed QoS. To demonstrate the path loss and power delay profile (PDP) in directional and Omni-directional antennas NYUSIM channel simulator is utilized.

The design and integration of intelligent energy management systems in hybrid Electric Vehicle (EV) charging stations, leveraging Industry 4.0 and renewable energy sources, is crucial for advancing sustainability, efficiency, and technological development. This paper introduces a pioneering hybrid EV charging station that employs hybrid power sources, combining photovoltaic panels, a battery, and a fuel cell, each operating at 240V and 14A. Utilizing wireless power transfer technology, the system comprises five integral blocks: a power source, a boost converter, a High-Frequency (HF) inverter, transfer coils, and EV batteries. The optimization process involves two key stages: i) maximum power point tracking optimization of the boost converter, ensuring maximum power generation by varying the duty cycle between 10% and 90%, and ii) the HF phase employing a class-ϕ2 inverter at 30 MHz, synchronized with the resonant frequency of wireless power transfer coils. Control is executed through a digital signal processor card utilizing zero-voltage switching for efficient operations. This design enhances sustainability in EV charging solutions by optimizing power transfer through the use of hybrid sources.

The conceptual reconstruction of Neiwan powerhouse is one of the key activities under the current ongoing mapping project of Taiwanese hydropower plants that mainly took place between 2013 and 2015 and is now focused on micro, pico, and historical power plants. Judging from the fact that the oldest hydropower plant in Taiwan named Guishan starts its operation in 1905, Neiwan powerhouse was among the very first powerhouses that were built across the island to support the electrification of Taiwan. However, the main function of the single turbine equipped Neiwan micro powerhouse was to support mainly the military needs and protect the territories occupied by Japanese troops. Since the powerhouse was built in 1909 and operates only something about 10 year there are very little physical materials or evidence along with contemporaries. Therefore the further reconstruction is based mainly on physical observation of the remains located at the site, old photographs, related articles, treatises and typology of mechanical and civil constructions of other hydropower plant cases in Taiwan hence this paper´s main intention is to pitch a concept reconstruction rather than definite conclusion.

This research paper is part of the wider project concerning the very first detailed mapping of the overall Taiwanese hydro-power plants that took place from 2013 up to 2015 and it is currently in evaluation and finalization stage. The case of Shanping hydro-power plant has been carefully studied, photographed, documented and mapped in situ. It was one of the isolated hydro-power plant projects originally built to supply the remote area with the specific designation. Shanping hydro-power plant, as well as the other units from the early hydro-power generation era in Taiwan, are considered to be the technological heritage of civil and mechanical engineering that reflects later in all the further projects up to nowadays modern Taiwanese hydro-power plants. Unfortunately, most of the hydro-power houses from the older periods were severely damaged or destroyed by natural causes which were also the case of Shanping unit. The research is trying to reconstruct the original location of the powerhouse and its supporting structures based on available historical documents, previous studies, comparative methodology, and the current on-site observation.

To reduce solar power production invariance, it is critical to study varying patterns of power production in the concerned region. Analyzing the patterns of past power production trends can help simulate power production scenarios for future. The current study area is around Amsterdam, located in Netherlands. PVoutput.org website is used to mine 6 months of solar power production data for 120 stations around Amsterdam city. FME Workbench software is used to actively fetch the data from the mentioned website and manage in a MySQL database. Solar attenuation maps created using ArcGIS, helped to graphically visualize the variations in solar power production at different times and locations. Further, spatial autocorrelation is checked between the stations using semi-variograms in geostatistical tool of ArcMap. This feature allows to check whether the stations located close to each other are more correlated to each other rather than stations which are far apart. The statistical data analysis of power production can aid solar power production companies to better interpolate and predict solar power in advance for the concerned study region.

This paper presents two control design strategies for voltage regulation in a single inductor dual output (SIDO) DC-DC Buck converter system. Based on a nominal multiple input multiple output (MIMO) plant model and performance requirements, both an LQR and a decoupled PI control laws are designed to control the power converter system, under parametric uncertainties such as voltage source variation, CPL power variation, and load resistance variation. Therefore, the SIDO converter can cascade operating, which may cause the undesired effects of voltage oscillation and reduce the system's stability margin. The control performance was assessed under both uncertainties resistive loading and power variation of a constant power load (CPL). A SIDO DC-DC Buck converter board has been developed for experimental tests. The experimental results show that the LQR strategy, compared to the PI strategy, presented a robust performance in the presence of parametric uncertainties in the resistive loads being, however, sensitive to uncertainties due to the presence of CPL loads.

Monogenity is a classical area of algebraic number theory that is very actively researched even today. This paper is a collection of the results obtained during the last few years in this area. Several of these results were presented at the series of online conferences "Monogenity and power integral bases".

During the conceptual and preliminary design stage of a ship, designers need to ensure that the selected principal dimensions and parameters are good enough to deliver a stable ship (statically and dynamically) besides deadweight and speed. To support this, the initial intact stability of the proposed ship is required to be calculated, and in doing so, the lightship weight and its detailed breakdown are necessary to be known. After hull steel weight, machinery weight, mainly, marine propulsion and power generation machinery, play a vital role in the lightship weight estimate of a ship due to its robustness. The correct estimation of respective weights improves the accuracy of calculating a ship's initial stability typically to be designed and built. Hence, it would be advantageous for the designer to convince the ship owner. A total of 3006 marine propulsion (main marine diesel) engines and 348 power generation (auxiliary marine diesel) engines/generators of various power output (generators output for auxiliary engines), engine RPM and cylinder number of different engine makers are collected. These are analyzed and presented in both tabular and graphical forms to demonstrate the possible relationship between marine propulsion engine weight and power generation engine weight, and their respective power output, RPM, cylinder number, power-RPM ratio and power-RPM ratio per cylinder.In this article, the authors have attempted to investigate the behavior of marine propulsion engine weight and power generation engine/generator weight regarding engine power output, generator power output, engine RPM and cylinder number (independent variables). Further attempts have been made to identify those independent variables that influence the weight of the marine propulsion engine and power generation engine/generator (dependent variables), and their interrelationships. A mathematical model has thus been developed and proposed, as a guiding tool, for the designer to estimate the weight of main and auxiliary engines more accurately during the conceptual and preliminary design stage.

Improving performance and promoting sustainability in women's handball are key objectives to maximize the potential of female players and ensure the long-term viability of the sport. In this context, training with Olympic movements and their derivatives improves the development of strength, power, and speed, which are determinants of performance in team sports. The aim of this study was to determine if training with Olympic movements produces significant improvements in jumping, throwing, sprinting, and change of direction performance in women handball players. Twenty-one female handball players participated in the study (10 for the control group and 11 for the intervention group). Age ranged from 15 to 17 years. All participants performed four assessment tests (Abalakov Test, throw test, 20-meter Sprint and V-Cut Test) to determine jump height, throwing speed, running speed, and change of direction ability. Measurements were carried out before and after the intervention. For six weeks, the control group performed the strength work established by the club twice a week while the intervention group additionally performed training with Olympic movements. Significant differences (p <0.05) were found between the pre and post measurement of the control group and the intervention group in jump height, throwing speed and running speed, being higher in the intervention group. For the change of direction, no significant differences were found. Between groups, significant differences were observed at the end of the intervention for jump height and running speed. The conclusion of this study was that, by training with Olympic movements, in addition to regular training, could produce greater improvements in jumping performance, throwing speed and running speed in female handball players.

Concern about the planet's future has motivated governments around the world to adopt policies that promote more responsible energy consumption. Reducing emissions of the principal cause of climate change man-made greenhouse gases requires greater system efficiency and the utilization of renewable energy sources. The generation of electricity is the single largest source of hazardous pollutants, followed by the transportation sector. This is true due to the extreme reliance on petroleum and its derivatives that these industries have. Electric mobility is receiving more attention from businesses, governments, and academic institutions as a means to reduce the negative impacts of current energy consumption. Without measures to address common technical issues, electric vehicles would strain electrical infrastructure. In order to determine the best strategy for switching operations and feeder reconfiguration, this research presents a helpful hybrid genetic algorithm particle swarm optimization (HGAPSO) method. Meet transmission limits while decreasing real power losses and enhancing the system's bus voltage profile. The effects of HGAPSO on power losses and voltage distributions in the network are analyzed. Then, a report is produced contrasting GA and PSO. This cross-breeding of GA and PSO led to HGAPSO. This important problem can be solved more effectively with the use of new or improved algorithms. To find the optimal reconfiguration and properly rearrange transmission network interconnection, it employs a plethora of heuristic optimization algorithms. The objective is to limit bus voltage variations while maintaining the system's radial topology and minimizing power usage. The reliability and performance of the procedure were evaluated using MATLAB's IEEE 33-bus communication network. The outcomes demonstrate the effectiveness of the proposed technique, which cuts down on power waste during standalone runs and speeds up the processing time.

Background: Ice formation on power transmission lines presents significant risks, including structural damage and power outages. Traditional methods for detecting ice on these lines have limitations, particularly in challenging environmental conditions. This study aims to enhance ice detection accuracy by introducing a novel image segmentation and edge detection methodology using improved multi-scale Retinex and advanced morphological operations. Method: The proposed method integrates multi-stage image processing techniques, including image enhancement, grayscale conversion, thresholding, segmentation, object isolation, and edge detection. High-resolution binocular cameras were used to capture images of ice formations on transmission lines. The effectiveness of the method was assessed through a series of metrics, including accuracy, sensitivity, specificity, and precision, and compared with existing methodologies. Results: The proposed method demonstrated superior performance in both ice detection and thickness measurement. The method effectively identified and isolated ice formations under various conditions with an average accuracy of 98.35%, sensitivity of 91.63%, specificity of 99.42%, and precision of 96.03%. Additionally, the analysis of ice thickness measurements further highlighted the method’s accuracy, with a notably low root mean squared error (RMSE) of 1.20 mm and mean absolute error (MAE) of 1.10 mm, along with a strong R-squared value of 0.95. These statistical metrics show that the proposed method not only outperforms previous methods in consistency and alignment with manual measurements but also stands out as the most reliable option for tasks requiring precise measurements, offering significant advancements in accuracy and reliability over existing methodologies. Conclusions: The enhanced image segmentation and edge detection approach provides a more accurate and reliable method for monitoring ice formations on power transmission lines.

Wide bandgap (WBG) power semiconductor devices are increasingly replacing silicon IGBTs in high-power and high-voltage power electronics applications. However, there is a significant gap in the literature regarding efficient testing methodologies for high-power and high-voltage converters under constrained laboratory resources. This paper addresses this gap by presenting comprehensive, hardware-focused testing methodologies for high-power and high-voltage WBG power semiconductor based converters, preceding the control evaluation phase. The proposed methods enable thorough evaluation and evaluation of converter hardware, including device switching characteristics, driving circuit functionality, thermal management performance, insulation integrity, and sustained operation at full power. We utilize the double pulse test (DPT) to characterize switching performance in a two-level phase leg configuration, extract circuit parasitics, and validate magnetic components. The DPT is further applied to optimize gate driving circuits, validate overcurrent protection mechanisms, and measure device on-resistance. Additionally, a multicycle test is introduced to rapidly assess steady-state converter performance and estimate efficiency. Recognizing the critical role of thermal management in high-power converters, our methodologies extend to the experimental extraction of key thermal parameters—such as junction-to-ambient thermal resistance and thermal capacitance—via a heat loss injection method. A correlation method between temperature sensor measurements and junction temperature is presented to enhance the accuracy of device temperature monitoring during tests. To ensure reliability and safety, dielectric withstand tests and partial discharge measurements are conducted at both component and converter levels under conventional 60 Hz sinusoidal and high-frequency PWM waveforms. Finally, we highlight the importance of testing converters under full voltage, current, and thermal conditions through power circulating tests with minimal power consumption, applicable to both non-isolated and isolated high-power converters. Practical examples are provided to demonstrate the effectiveness and applicability of these hardware testing methodologies.

The operation of electricity and natural gas transmission networks in the U.S. are increasingly interdependent, due to the growing number of installations of gas fired generators and the penetration of renewable energy sources. This development suggests the need for closer communication and coordination between gas and power transmission system operators in order to improve the efficiency and reliability of the combined energy system. In this paper, we present a co-simulation platform for examining the interdependence between natural gas and electricity transmission networks based on a direct current unit-commitment and economic dispatch model for the power system and a transient hydraulic gas model for the gas system. We analyze the value of day-ahead coordination of power and natural gas network operations and show the importance of considering gas system constraints when analyzing power systems operation with high penetration of gas generators and renewable energy sources. Results show that day-ahead coordination contributes to a reduction in curtailed gas during high stress periods (e.g., large gas offtake ramps) and a reduction in energy consumption of gas compressor stations.

The next-generation communication systems demand integration of sensing, communication, and power transfer (PT) capabilities, requiring high spectral efficiency, energy efficiency, and low cost, while also necessitating robustness in high-speed scenarios. Integrated sensing and communication systems (ISACS) exhibit the ability to simultaneously perform communication and sensing tasks using a single RF signal, while simultaneous wireless information and power transfer (SWIPT) systems can handle simultaneous information and energy transmission, and orthogonal time frequency space (OTFS) signals are adept at handling high Doppler scenarios. Combining the advantages of these three technologies, a novel cyclic prefix (CP) OTFS based integrated simultaneous wireless sensing, communication, and power transfer system (ISWSCPTS) framework is proposed in this work. Within the ISWSCPTS, the CP-OTFS matched filter (MF) based target detection and parameters estimation (MF-TDaPE) algorithm is proposed to endow the system with sensing capabilities. To enhance the system’s sensing capability, a waveform design algorithm based on CP-OTFS ambiguity function shaping (AFS) is proposed, which is solved by iteratively method. Furthermore, to maximize the system’s sensing performance under communication and PT Quality of Service (QoS) constraints, a semidefinite relaxation (SDR) beamforming design (SDR-BD) algorithm is proposed, solved using through SDR technique. Simulation results demonstrate that the ISWSCPTS exhibits stronger parameter estimation performance in high-speed scenarios compared to orthogonal frequency division multiplexing (OFDM), waveform designed by CP-OTFS AFS demonstrates superior interference resilience, and beamforming designed by SDR-BD strikes a balance in the overall performance of the ISWSCPTS.

The sustainable development of an area is highly dependable on reliable electrical energy supply. Microgrids are important in integrating distributed energy resources (DERs) using power electronic converters. However, microgrid control becomes challenging with the increasing number of distributed generators and loads. With the conventional droop control method, power contributions from DER converters cannot be accurately shared due to a mismatch of line impedances. In this paper, an augmented hierarchical control mechanism is proposed to solve the issues mentioned above. This hierarchical control mechanism consists of primary and secondary controllers. The primary stage utilized the droop controller to improve optimal power flow, mainly for the resistive network. The secondary stage is based on an improved methodology to compensate for the voltage and frequency variations during small and large signal disturbances. Moreover, the modelling and analysis for PMSG-based wind energy conversion systems are also presented. The response of the primary controller for the active and reactive power sharing is investigated. The analysis emphasizes the demonstration of optimal power-sharing under normal and abnormal conditions for the considered load. Finally, the suggested robust controller's performance is evaluated in MATLAB environment and simulation results show the proposed scheme's superiority under different operating conditions.

A new power receiving unit (PRU) is proposed in this paper for the resonant wireless power transfer (WPT), which is characterized by the capability of attracting high power from the power transmitting unit (PTU). The resonant WPT is designed for delivering the electrical power to the PRU attached on an electrical vehicle (EV) chassis 50cm away from a PTU installed on the ground. The proposed PRU uses only the passive elements such as inductors, diodes and the capacitors, which needs no initial power from the EV. It is then applicable for charging a battery to several hundred volts for even a first-time charging battery. At a switching frequency of the resonant WPT in the experiment being 4MHz, the proposed PRU behaves itself as a negative impedance converter (NIC) in the subharmonics of 4MHz. The NIC effect plus the subharmonic oscillation causes an instability current charging the battery connected to the PRU. In this paper, we simulated the PRU and performed the experiment. The experiment demonstrates a battery charging of 150W from 50cm away using three D-mode GaN HEMT transistors via the instability current ramp. The power transfer efficiency (PTE) improved as the power delivered to load (PDL) goes higher. The best power transfer efficiency (PTE) is 65% in the present findings. The simulation analysis shows that the circuit allows itself be used to much higher power transfer when it is implemented with more GaN HEMT transistors connected in parallel. The theoretical derivation of the PRU circuit is also used to support both the experimental and simulation results.

The local reactive power control in distribution grids with a high penetration of distributed energy resources (DERs) is essential in future power system operation. Appropriate control characteristic curves for DERs support stable and efficient distribution grid operation. However, the current practice is to configure local controllers collectively with constant characteristic curves that may not be efficient for volatile grid conditions or the desired targets of grid operators. To address this issue, this paper proposes a time series optimization-based method to calculate control parameters, which enables each DER to be independently controlled by an exclusive characteristic curve for optimizing its reactive power provision. To realize time series optimizations, the open-source tools pandapower and PowerModels are interconnected functionally. Based on the optimization results, Q(V)- and Q(P)-characteristic curves can be individually calculated using the linear decision tree regression to support voltage stability and provide reactive power flexibility and potentially reduce grid losses and component loadings. In this paper, the newly calculated characteristic curves are applied in two representative case studies, and the results demonstrate that the proposed method outperforms the reference ones suggested by grid codes.

Induction heating is a fast, reproducible, and efficient heating method used in various manufacturing processes. However, there is no established additive manufacturing (AM) process based on induction heating using wire as feedstock. This study investigates a novel approach to AM based on inductive heating, where a steel wire is melted and droplets are detached periodically using a two-winding induction coil. The process parameters and energy input into the droplets are characterized. The induction generator exhibits sluggish response to the excitation voltage, resulting in a lag in the coil current. The process is captured using a high-speed camera, revealing regular droplet formation and uniform size and shape when operated within an appropriate process window. Larger drops and increased spatter formation occur outside this window. The proposed method allows for the production of droplets with almost spherical shapes. Further analysis and characterization of droplet formation and energy input provide insights into process optimization and overall efficiency.

The paper addresses the energy consumption minimization problem in wireless powered communication networks (WPCNs) and proposes a DT-SWIPT-assisted time allocation scheme, named DaTA, such that the wireless station can share the remaining energy after transmission to the HAP to those who have not transmitted to the HAP to minimize the energy consumption of the network. In addition to proposing a new frame structure, the paper also considers the SNR (Signal-to-Noise) constraint to guarantee that the HAP can successfully receive data from wireless stations. In the paper, the energy consumption minimization problem is formulated as a nonlinear programming model. We employ the SQP (Sequential Quadratic Programming) algorithm to figure out the optimal solution. Moreover, a heuristic method is proposed as well to obtain a near-optimal solution in a shorter time. Simulation results showed that the proposed scheme can have better performance than the related work in terms of energy consumption and energy efficiency.

Power generation using renewable technologies has become a primordial option to satisfy the energy demand all over the world, being solar concentrating technologies widely applied for this purpose. A combination of Parabolic Trough Collector with Direct Steam Generation has been considered an excellent option for power generation, due to the economic cost and complexity in the plant are reduced. The thermal evaluation of the solar power plant as well as the PTC in the DSG process is very important in viability and economic analysis. In this sense, as the main objective of this work, a numerical tool for evaluating DSG with PTC technology has been developed. The software SOLEEC is a versatile, reliable, accurate and friendly to the user for thermally evaluating a DSG with PTC technology. The user has the possibility to compare the thermal behavior of different geometrical dimensions for a PTC; and even consider different materials; in order to satisfy the demand of superheated steam by a DSG process. The software has an error less than 5% when compared with literature results and in this paper is used to evaluate a power plant in Mexico obtaining that the change to DSG proposing different PTC could reduce the solar field about 35%.

We consider a control problem for a diffusive PDE model of heterogeneous population of thermostatically controlled loads (TCLs) aiming to balance the aggregate power consumption within a given amount of time. Using the Green’s function approach, the problem is formulated as an approximate controllability problem for a residue depending on control parameters nonlinearly. A sufficient condition for approximate controllability is derived in terms of initial temperature distribution, operation time of TCLs and threshold value of the aggregate power consumption. Case studies allow to reveal the advantages of the proposed solution from numerical calculations point of view.

The fluctuation of the conditions on Lake Limboto affects people's activities around the lake. They try to survive by facing the problem of the lake, which is shallowing and narrowing. Yet the lake is predicted will be disappeared in 2030. This means that the productivity of the lake also diminishes. This article aims to analyze how the communities around the lake respond to the evolution and shocking prediction toward the lake into their daily activities. This study uses an interdisciplinary approach by integrating some fields of study to understand and solve the problems. One of the approaches involves interviewing people around the lake. Nevertheless, the base of the study is socio-cultural studies, which uses also old texts and oral literature as the support of the study. The research needs the theory of cultural studies to look at the survival and resilience of the people of lake so that they form their special daily activity. The results of the study show that some people know that there is a prediction of disappearing of the lake, but they have not anticipated it, as if this problem is only a government affair. They still live at the lake bank, try to survive and to be resilience even in poor conditions.

The unprecedented progress in Artificial Intelligence (AI), particularly in deep learning algorithms with ubiquitous internet connected smart devices, has created a high demand for AI computing on the edge devices. This review studied commercially available edge processors, and the processors that are still in industrial research stages. We categorized state-of-the-art edge processors based on the underlying architecture, such as dataflow, neuromorphic, and Processing in-Memory (PIM) architecture. The processors are analyzed based on their performance, chip area, energy efficiency, and application domains. The supported programming frameworks, model compression, data precision, and the CMOS fabrication process technology are discussed. Currently, most of the commercial edge processors utilize dataflow architectures. However, emerging non-von Neumann computing architectures have attracted the industry in recent years. Neuromorphic processors are highly efficient for performing computation with fewer synaptic operations, and several neuromorphic processors offer online training for secured and personalized AI applications. This review found that the PIM processors show significant energy efficiency and consume less power compared to dataflow and neuromorphic processors. The future direction of the industry would be to implement state-of-the-art deep learning algorithms in emerging non-Von Neumann computing paradigms for low power computing on the edge devices.

As the penetration of renewable energies increases, their acceptance of the power grid system is becoming an important issue. In the case of South Korea, a 22.9kV transformer is frequently utilized to reduce the power loss of the generated renewable energy transmission, so the power quality at the point of common connection (PCC) is inevitably influenced by the nonlinearity of the transformer and the uncertainty of the inductance and resistance of the transmission line. In this paper, we present a point of common connection voltage-modulated direct power control (PCCVM-DPC) system that enhances power quality at the PCC. First, we present the mathematical dynamics of active and reactive power at the PCC side, which contains the step-up transformer’s nonlinearity, the grid voltage harmonics, and the parameter uncertainties. By analyzing the disturbance terms of the PCCVM-DPC system, we present the disturbance observer (DOB) for the PCCVM-DPC system. To assess the efficacy of our approach, we perform comparative studies of the PCCVM-DPC without DOB and PCCVM-DPC with DOB by constructing the simulation environment based on the commercial step-up transformer and ESS inverter datasheet. We have validated that the active and reactive power control performance of the PCCVM-DPC with DOB outperforms the PCCVM-DPC without DOB from the observation that the current total harmonic distortion reduced by more than 40% compared to the PCCVM-DPC without the DOB.

This book review addresses the contribution of Tim Marshall’s “The Power of Geography”. The purpose of this essay is to highlight the significant role of geography in shaping political landscapes, alliances, and global affairs through the book review. What is new about this essay is its accessible presentation of complex geopolitical concepts, making it a valuable resource for students of geography and readers interested in global politics. Through the analysis of case studies and historical background, the book illuminates the interplay between physical landscapes, territoriality, and power dynamics. The findings highlight the continuing influence of geography on nations, regional identities, and the evolving global order.

The world population increased from 1 billion in 1800 to around 8 billion today. The Population Division of the United Nations predicts a global population of approximately 10.4 billion people by the end of the century. That represents over 2 billion more people. Moreover, the global community is currently experiencing a precarious state due to the enduring repercussions of the COVID-19 pandemic across all sectors, including energy. Given the rising global population and the limited availability of primary energy resources, we must reach a balance between the demands of a growing human population and the planet’s carrying capacity. The dreadful conflict in Ukraine has precipitated an enormous energy crisis. This crisis served as a warning to the world population of how much they depend on this resource to survive. In France, building sectors (i.e., residential and tertiary) alone consume 45% of the final energy disposable. It is the first energy consumer of the country and one of the most polluting (i.e.; about 34% of CO2 emitted by France). Consequently, we must consider alternative energy resource forms (i.e.; substitution energy forms). Harvesting energy from the building envelope may be a viable technique for partially satisfying the electricity demands of building users. In this context, scientific research offers considerable potential for developing more innovative and efficient systems. This article aims to review the state of the art of advances on the subject to orient and further optimize energy production systems, particularly electricity. This work will address several points of view: Discusses the overall backdrop of the present study and introduces the subject ; details the research strategy and procedures used to produce this paper ; develops state of the art on the potential for generating or recovering power from the building envelope ; presents the SWOT analysis of the earlier-described systems. And finally, it concludes by offering findings and viewpoints.

Wearable sensors have become increasingly popular for assessing athletic performance, but the optimal methods for processing and analysing the data remain unclear. This study investigates the efficacy of discrete and continuous feature extraction methods, separately and in combination, for modelling countermovement jump performance using wearable sensor data. We demonstrate that continuous features, particularly those derived from Functional Principal Component Analysis, outperform discrete features in terms of model performance, robustness to variations in data distribution and volume, and consistency across different datasets. Our findings underscore the importance of methodological choices, such as signal type, alignment methods, and model selection, in developing accurate and generalisable predictive models. We also highlight the potential pitfalls of relying solely on domain knowledge for feature selection and the benefits of data-driven approaches. Furthermore, we discuss the implications of our findings for the broader field of sports biomechanics and provide practical recommendations for researchers and practitioners aiming to leverage wearable sensor data for athletic performance assessment. Our results contribute to the development of more reliable and widely applicable predictive models, facilitating the use of wearable technology for optimising training and enhancing athletic outcomes across various sports disciplines.

Modern exchange theories model a large market, but do not explain single exchange. The paper considers the phenomenon of single exchange and formulates the general exchange problem in the form of a system of two equations, subjective and objective. Subjective equilibrium is given by the Walras-Jevons marginal utility equation. Objective equilibrium equations by Walras and Jevons are averaged over all transactions in the market and can only give a rough general picture without explaining the specific price of an individual exchange. An exchange micro-condition must be found that, when averaged, will give the Walras market equilibrium macro-condition. The study of the internal structure of exchange leads to the need to consider power. The concept of generalized power is introduced. It is generalized power that serves as the primary comparable and measurable objective basis of exchange. The power theory of exchange provides the objective price-equation. It is demonstrated that money is a measure of generalized power in exchange and a certification of generalized power in subsequent exchanges. The proposed theory is able to uniformly explain any exchange, including a single one, which is impossible with the existing theories of exchange.

In this work, an analog front-end (AFE) circuit for Electrocardiogram (ECG) detection system has been designed, implemented, and investigated in an industry-standard Cadence simulation framework using advanced technology node of 45 nm. The AFE consists of an instrumentation amplifier, a Butterworth band-pass filter (with fifth-order low-pass and second-order high-pass sections), and a second-order notch filter- all are based on two-stage, Miller-compensated operational transconductance amplifiers (OTA). The OTAs have been designed employing the $g_m/I_D$ methodology. Both the pre-layout and post-layout simulation were carried out. The layout consumes an area of 0.0058 mm$^2$ without the resistors and capacitors. Analysis of various simulation results were carried out for the proposed AFE. The circuit demonstrates a post-layout bandwidth of 239 Hz with a variable gain between 44 to 58 dB, a notch depth of -56.4 dB at 50.1 Hz, a total harmonic distortion (THD) of -59.65 dB (less than 1\%), an input referred noise spectral density of $

Abstract: High power semiconductor laser is a kind of photoelectric device with high efficiency and high stability, the performance of its drive system directly affects its output characteristics and service life. In order to solve the problems of stability and robustness of the output power of semiconductor laser, a semiconductor laser driving power supply with high efficiency, low ripple and strong anti-interference ability was developed. The power supply adopts full-bridge LCC resonant power topology. Firstly, a mathematical model is established to analyze the relationship between LCC resonator parameters and output current gain. Secondly, a LCC resonator parameter design method is proposed to reduce the current stress of components, and the variable frequency phase shift (PFM-PWM) composite control strategy and linear active disturbance rejection control (LADRC) algorithm are proposed, which not only ensures the zero voltage (ZVS) conduction of MOS tube, but also reduces the on-off loss of MOS tube. Improved power efficiency and suppressed output current ripple; At the same time, the instability of the output current is ensured due to the input voltage, load and parasitic parameter change of the circuit. Finally, the simulation and experimental results show that the power supply can be continuously adjustable in the output current range of 0-40A, the current ripple is less than 0.8%, and the working efficiency is up to 92%. It has the characteristics of high stability, small ripple, high efficiency, low cost and good robustness.

This paper presents a new methodology to evaluate the performance of an electric vehicle hybrid power system consisting of a fuel cell and a supercapacitor. The study compares the results with those obtained for a battery-electric vehicle. The methodology extends to three driving modes, ECO, NORMAL, and SPORT, corresponding to conservative, moderate, and aggressive acceleration, and three driving conditions, low, medium, and high energy demand. We develop a simulation process to evaluate the energy consumption and the energy rate of a specific electric vehicle used as a prototype for the study. The methodology applies to a driving route that includes acceleration, deceleration, braking, and constant speed segments reproducing standard driving conditions in urban journeys. The proposed method considers combined driving modes, ECO, NORMAL, and SPORT, in each acceleration process, with variable fractions, 0% to 100%, for each mode. This methodology optimizes the simulation results as it fits the current driving way in urban environments. The simulation results show an average reduction in energy consumption of 37% and 27.1% in vehicle weight, contributing to lower energy use. The study concludes that using a hybrid power system, fuel cell/supercapacitor, instead of a battery in electric vehicles is beneficial, especially in journeys with frequent acceleration processes.

One of the major problem of photovoltaic grid integration is limiting the solar-induced imbalances since these can undermine the security and stability of the electrical system. Improving the forecast accuracy of photovoltaic generation is becoming essential to allow a massive solar penetration. In particular, improving the forecast accuracy of large solar farms generation is important both for the producers/traders to minimize the imbalance costs and for the Transmission System Operators to insure stability. In this article, we provide a benchmark for the day-ahead forecast accuracy of utility scale PV plants in 1325 locations spanning the country of Italy. We then use these benchmarked forecasts and real energy prices to compute the economic value of forecast accuracy and accuracy improvement in the context of the Italian energy market regulatory framework. Through this study, we further point out some several important criticisms of the Italian “single pricing” system that brings to paradoxical and counterproductive effects regarding the need to reduce the imbalance volumes. Finally, we propose a new market-pricing rule and innovative actions to overcome these undesired effects of the current dispatching regulations.

This paper shows that the percolation clusters from elementary cellular automata {30, 45, 60, 86, 99, 105, 129, 150, 153, 169, 182, 183, 184, 195 and 225 exhibit strong power law behavior, either under random initial conditions, a single occupied cell, or both. Most of the tail exponents are less than unity, implying diverging means and variances of cluster sizes. The analysis presented here is admittedly coarse in an effort to expedite its dissemination.

The object of study in the article is the auxiliary variable-frequency electric drive onboard of an AC electric locomotive, and more precisely, the structure and parameters of the control system of the active corrector of power factor (ACPF), which is part of the electric drive, as a unit that ensures electromagnetic compatibility of the electric drive with other equipment on board the electric locomotive and catenary and its energy efficiency. The topic of the article's research is the substantiation of the structure of the ACPF control system, the choice of types (transfer functions) of controllers and the calculation of their parameters. The research method chosen was the calculation of the transfer functions of the controllers of the cascaded loops control system, followed by computer simulation using the OrCAD software. The results of simulating a cascaded two loops control system of an ACPF with different types of controllers are presented and analytically compared. It is concluded that it is advisable to use a cascaded two loops control system, containing a voltage control loop and a current control loop. The best results show the simulation when using an aperiodic current controller (A-controller) and a proportional-integral voltage controller (PI-controller). The data obtained serve as the basis for further improvement of the operation of the ACPF by enhancing and optimizing the settings, structure and algorithms of the control system, which, with the selected hardware of power converter unit, will allow the ACPF to perform its functions with a high degree of reliability in an entire range of disturbing and control influences.

This article presents a proposed system that enables energy transfer from the dc grid to a single-phase onboard grid, operating at an hi frequency. In addition to the energy transfer function, it additionally enables compensation of reactive power in the ac grid when the converter operates at less than rated power. To operate in compensator mode, it is necessary to decouple the current from the grid into active and reactive components and control them independently. To achieve good dynamics, synchronizers that operate in the dq system are used. In the case of a single-phase grid, it requires such a synchronizer to generate virtual quadrature signals. The used systems based on second-order generalized integrator are good, but to improve dynamics in the work a quadrature generator based on trigonometric calculations was proposed. The developed system was implemented in a proportional resonant current control system. Tests performed in steady state and in dynamic states related to typical grid disturbances showed better dynamic properties than the standard integrator-based system.Keywords: power transfer; compensator; P+R controller

Contactless charging is evolving fast in many domains and applications such as the electrical vehicles (EV). The principle consists of transferring energy between two systems without having any electrical connection between them. This power transfer can be realized by emitting a magnetic field for Inductive Power Transfer (IPT). In the automotive domain, the application of contactless charging to supply power to the vehicle while driving is one of the solutions envisaged to solve the limited autonomy range of EV and reduced its cost but the system must comply with existing standards (e.g., allocated frequency range and radiated electromagnetic emissions), as summarized in this paper.

We present the results of direct numerical simulations of power spectral densities for kinetic energy, convective entropy and heat flux for unsteady Rayleigh-Bénard magnetoconvection in the frequency space. For larger values of frequency, the power spectral densities for all the global quantities vary with frequency f as f⁻². The scaling exponent is independent of Rayleigh number, Chandrasekhar’s number and thermal Prandtl number.

This research explores a novel approach to integrating offshore wind farms into smart microgrids through the development of an advanced model predictive control (MPC) strategy for offshore wind turbines. The MPC strategy comprehensively incorporates complex wind dynamics, such as wind speed, direction, and turbulence, ensuring an accurate representation of turbine behavior. Additionally, the research includes models addressing wind farm layout, wake effects, and electrical infrastructure, enhancing the modeling framework's fidelity and applicability to real-world offshore wind energy systems within a smart microgrid environment. The inherent variability of wind power, transmission technology limitations, and the need for seamless transitions between grid-connected and islanded operation modes in smart microgrids necessitate robust control mechanisms. These mechanisms ensure efficient power capture, grid stability, and optimal energy utilization. To tackle these challenges, the research proposes a smart microgrid design incorporating both AC-DC and DC-DC conversion technologies. This design leverages renewable energy sources like solar and wind with AC-DC conversion for efficient power capture, integrates DC energy storage systems to store excess energy during low demand periods, and utilizes power control mechanisms to manage energy flow effectively within the smart microgrid. The study emphasizes the importance of modeling and control strategies for both AC-DC and DC-DC converters within the smart microgrid framework. To enhance the microgrid's cost-effectiveness, priority is given to the utilization of solar PV energy sources. It also highlights the integration of protection systems for DC faults and coordinated control of AC/DC breakers and converters. This comprehensive approach aligns with the core principles of adaptability, reliability, and sustainability in smart grids, aiming to advance smart microgrid technologies and pave the way for a more resilient, efficient, and secure energy future.

Colombia has one of the largest numbers of internally displaced populations in the world and recently entered a period of post-conflict. These socio-political processes and trends have increased the migration of people towards cities and accordingly are affecting the distribution and occurrence of tropical diseases in its urban and peri-urban areas. Studies have suggested that many human phenomena such as urbanization scale according to the size of human populations regardless of cultural context. But other studies show that health epidemics such as malarial and human immunodeficiency virus infections, follow a scale-free distribution in terms of population size and density. We explore these relationships and dynamics in a tropical context using statistical analyses and available geospatial data to identify the scale dynamics between urbanization processes and disease transmission in Colombia. We found that rural populations and certain disease dynamics were described by power-laws that are frequently mentioned in urbanization studies. However, we found that malaria presented higher intensity of infection in human settlements of less than 50,000 individuals, particularly for ethnic indigenous populations. Results indicate that epidemics and urbanization dynamics do indeed follow scales in Colombia; findings that differ from previous epidemiological studies such as those for malarial infection. Additionally, we identified trends showing that malarial infections become endemic in peri-urban areas. Targeting such peri-urban locations and certain demographic groups are key for managing public health issues in the urbanizing tropics.

To show that underlying Schmitt's account of fascist politics lies a Gnostic-like metaphysical dualism separating the realms of value and power. Contrary to the normative political tradition of the West, which defends an ethical politics, Schmitt - jurist and theorist of the Nazis - aligns himself with Machiavelli and Hobbes to defend realpolitik: where sovereignty is ultimately a function of the Dictator's will alone. This paper shows the contradiction within such a position, which criticizes values in politics but by its advocacy, and its defense of the Dictator's willing, relies on valuation, choice, and hence the ethical.