Wave is a common environmental load that often causes serious damages to offshore structures. In addition, the stability for the submarine artificial slope is also affected by the wave loading. Although the landslide of submarine slopes induced by the waves has received wide attention, the research on the influence of solitary-wave is rare. In this study, a 2-D integrated numerical model is developed to investigate the stability of the foundation trench under the solitary wave loading. The Reynolds-Averaged-Stokes (RANS) equations are used to simulate the propagation of a solitary wave, while the current is realized by setting boundary inlet/outlet velocity. The pore pressure induced by the solitary wave is calculated by Darcy’s law and the seabed is characterized by Mohr-Coulomb constitutive model. Firstly, the wave model is validated through the comparison between analytical solution and experimental data. The initial consolidation state of slope under hydrostatic pressure is achieved as the initial state. Then, the factor of stability (FOS) for the slope corresponding to different distance between wave crest and slope top is calculated with the strength reduction method. The minimum of FOS is defined as the stability index for the slope with specific slope ratio during the process of dynamic wave loading. The parametric study is conducted to examine the effects of soil strength parameters, slope ratio and current direction. At last, the influence of upper slope ratio in a two-stage slope is also discussed.

Automotive aerodynamics comprises of the study of aerodynamics of road vehicles. Its main goals are reducing drag, minimizing noise emission, improving fuel economy, preventing undesired lift forces and minimizing other causes of aerodynamic instability at high speeds. The Ahmed body has the form of a highly simplified car, consisting of a blunt nose with rounded edges fixed onto a box-like middle section and a rear end that has an upper slanted surface, the angle of which can be varied. It retains vital features of real vehicles in order to study the flow fields around it and the related turbulence models which characterizes the actual flow at elevated Reynolds number. In the present study, the aerodynamic behavior of this body is investigated numerically by the aid of commercial CFD tool: Ansys Fluent. The results of the simulation are validated with available experimental data and results of the simulations from other literatures. The numerical data were obtained for a fixed free stream velocity of 25 m/s at the inlet. The simulations were performed at a fixed slant angle of 25 degree and zero yaw angle. The present study focuses on how local refinement of mesh inside the concerned body and the outside, helps affect the results and for which grid dependency test is the primary objective of this paper. The present study also helps demonstrate how the drag of the body behaves, which is mainly the effect of pressure drag force generated at the rear portion of the body. The study also focuses on important properties like the velocity magnitude at different locations for different meshing cases, and to capture the flow pattern in the front or near the wake region. The study can be further helpful to future researchers in determining resistance, fuel efficiency etc. helping designers to optimize in specialized areas for better efficiency.

A conventional 2D numerical model is improved by incorporating three submodels to consider different effects of secondary flow and a module for cohesive sediment transport. The model is applied to a meandering reach of Yangtze River to investigate secondary flow effects on cohesive sediment deposition, and a preferable submodel is selected based on the flow simulation results. Sediment simulation results indicate that the improved model predictions are in better agreement with the measurements in planar distribution of deposition as the increased sediment deposits caused by secondary current on the convex bank have been well predicted. Secondary flow effects on predicted amount of deposition become more obvious during the period when the sediment load is low and velocity redistribution induced by the bed topography is evident. Such effects vary with the settling velocity and critical shear stress for deposition of cohesive sediment. The bed topography effects can be reflected by the secondary flow submodels.

Numerical modelling is becoming a major tool for supporting environmental studies at different scales, thanks to the capability of up-to-date codes in reproducing the natural behaviour in a quite reliable manner. In evaluating the habitat diversity of anthropized rivers, however, many issues are rising because of the intrinsic complexity of the processes involved. Using a reach of the Po River in Italy as a case study, the present works aims to provide an estimate of the changes of the Eco-Environmental Diversity as a response to different constant flow discharges. The goals are achieved by means of two solvers of the iRIC suite, applied in sequence to firstly simulate the fluvial hydrodynamics and subsequently provide an estimate of the habitat conditions. Despite the simplifications intrinsically present in the models and the ones introduced for practical purposes, the results pointed out that the reduction of the flow discharge recently observed can threat the overall biological status of the river. Because of the modelling uncertainties, on the other side, these preliminary outcomes show the need for more research, both in terms of data acquisition and numerical schematization, for adequately evaluate the effects of transient hydrology on the river ecosystems. Moreover, additional field surveys are necessary to calibrate and validate the used model for having sufficiently reliable estimates.

To improve the effect of multi-point stretch forming of sheet metal, it is proposed in this paper to replace fixed ball head with swinging ball head. According to the multi-point dies with different arrangements, this research establishes the finite element models of the following stretch forming, i.e. fixed ball heads with conventional arrangement, swinging ball heads with conventional arrangement, swinging ball heads with declining staggered arrangement, and swinging ball heads with parallel staggered arrangement and then numerical simulation is performed. The simulation results show that by replacing fixed ball head with swinging ball head, the surface indentation of the formed part was effectively suppressed, the stress and tension strain distribution of the formed part was improved and the forming quality was improved; that the thickness of the elastic pad was reduced, the springback was reduced and the forming accuracy was improved; and that when the ball head was applied to multi-point die with staggered arrangement, better forming result was achieved, where the best forming result was achieved in combining the swinging ball heads with the multi-point die with parallel staggered arrangement. The forming experiments were carried out, and the experimental results were consistent with the trend of numerical simulation results, which verified the correctness of the numerical simulation.

Structural vibration induced by dynamic load or natural vibration is a nonnegligible factor in failure analysis. Based on vibrating boundary condition, impact resistance of shape memory alloy reinforced composites is investigated. In this investigation, modified Hashin’s failure criterion, Brinson’s model and visco-hyperelastic model are implemented into the numerical model to charactering the mechanical behavior of glass fiber/epoxy resin laminates, SMAs and interphase, respectively. First, fixed boundary condition is maintained in simulation to verify the accuracy of material parameters and procedures by comparing with experimental data. Then, a series of vibrating boundaries with different frequencies and amplitudes are applied during the simulation process to reveals the effect on impact resistances. The statistics of absorbed energy and contact force indicate that impact resistance of the composite under high frequency and large amplitude is lower than that under low frequency and small amplitude, and summarized by a mathematical expression.

Recently, there has been a growing interest in the production of electricity from renewable energy sources (RES). The RES investment is characterized by uncertainty, which is long-term, costly, depend on feed-in-tariff and support schemes. In this paper, we address the real option valuation (ROV) of a solar power plant investment. The real option framework is investigated. This framework considers the renewable certificate price, furthermore the cost of delay between establishing and operating the solar power plant. The optimal time of launching the project and assess the value of deferred option are discussed. The new three stage numerical methods are constructed, the Lobatto3C-Milstein (L3CM) methods. The numerical methods are integrated with concept of Black-Scholes option pricing theory, and applied in option valuation for solar energy investment with uncertainty. The numerical results of L3CM, finite difference and Monte Carlo methods are compared to show the efficiency of our methods. Our data set refers to the Arab Republic of Egypt.

Drafting formations have been long recognized as highly effective for reducing drag and enhancing athletic performance, particularly in race walking events. The precise spacing and positioning of the race walkers are critical to optimizing the effectiveness of drafting. In this study, the drag reduction of 15 drafting formations is investigated using wind-tunnel experiments and CFD numerical simulations. The results show excellent consistency in drag reduction rate between the two methods, with differences being within 10%. This can be attributed to spacing replacing body shape differences as the primary factor influencing drag reduction. Optimal double, triple, and quadruple drafting formations produce the same results in both wind-tunnel experiments and CFD simulation, resulting in drag reductions of 67%, 66%, and 81% (wind-tunnel) and 65%, 72%, and 85% (CFD). The sources of drag differences in the two methods are discussed from various aspects. The flow field obtained through CFD analysis is used to examine the mechanism of drag reduction, revealing that drafting formations have a significant shielding effect on incoming air, which reduces the number and speed of airflow impacting the core race walker. This shielding effect is identified as the primary cause of drag reduction. Using an empirical model for mechanical power output, optimal double, triple, and quadruple drafting formations enhance sport economy (4.4-5.7%), speed (3.61-4.67%), and performance (173.8-223.3s) compared to race walking alone. The findings can serve as a reference for race walkers' positioning strategy and provide insights for considering drafting formations in various running events.

The ground consists of many layers of soil with different properties. The propagation speed and path of seismic waves are affected by different soil layers. It is necessary to understand that layered soil exhibits different dynamic behaviors and responses under the action of seismic waves. This study utilized weathered soil and silica sand as materials to create multi-layered soil conditions with varying degrees of compaction. By conducting 1 g shaking table test on multi-layered soil, the interaction and influence between different soil layers under different earthquake conditions were observed. The approach of numerical analysis aims to validate the experimental results and provide an in-depth understanding of the dynamic behaviors of multi-layered soil grounds during seismic events. The results of this study show that the amplification effect of seismic waves is related to the number of soil layers and the degree of compaction of the soil layers. This indicates that the multi-layered soil ground and the behavior of the soil layers play an important role in the propagation and impact of seismic waves, and this amplification effect is of great significance in actual seismic disaster risk assessment and design.

Since the first case of 2019 novel coronavirus disease (COVID-19) detected on Jan 30, 2020, in India, the number of cases rapidly increased to 3819 cases including 106 deaths as of 5 April 2020. Taking this into account, in the present work, we are studying a Bats-Hosts-Reservoir-People transmission fractional-order COVID-19 model for simulating the potential transmission with the thought of individual social response and control measures by the government. The real data available about infectious cases from $14^{th}$ March to $26^{th}$ March 2020 is analysed and accordingly various parameters of the model are estimated or fitted. The Picard successive approximation technique and Banach's fixed point theory have been used for verification of the existence and stability criteria of the model. Numerical computations are done utilizing the iterative Laplace transform method. In the end, we illustrate the obtained results graphically. The purpose of this study is to estimate the effectiveness of preventive measures, predicting future outbreaks and potential control strategies using the mathematical model.

Façade elements are a building component that satisfies multiple performance parameters. Among other things, “advanced façades” take advantage of hybrid solutions, such as assembling laminated materials. In addition to the enhanced mechanical properties that are typical of optimally composed hybrid structural components, these systems are energy-efficient, durable, and offer lighting comfort and optimal thermal performance, an example of which is the structural solution developed in collaboration with the University of Zagreb and the University of Ljubljana within the Croatian Science Foundation VETROLIGNUM project. The design concept involves the mechanical interaction of timber and glass load-bearing members without sealing or bonding the glass-to-timber surfaces. Following earlier research efforts devoted to the structural analysis and optimization of thus-assembled hybrid Cross-Laminated Timber (CLT)-glass façade elements, in this paper, special focus is given to a thermal and energy performance investigation under ordinary operational conditions. A simplified numerical model representative of a full-size building is first presented by taking advantage of continuous ambient records from a Live-Lab mock-up facility in Zagreb. Afterwards, a more detailed Finite Element (FE) numerical analysis is carried out at the component level to further explore the potential of CLT–glass façade elements. The collected numerical results show that CLT–glass composite panels can offer stable and promising thermal performance for façades similar to national and European standard requirements.

Corrugated cardboard is an ecological material, mainly because, in addition to virgin cellulose fibers also the fibers recovered during recycling process are used in its production. However, the use of recycled fibers causes slight deterioration of the mechanical properties of the corrugated board. In addition, converting processes such as printing, die-cutting, lamination, etc. cause micro-damage in the corrugated cardboard layers. In this work, the focus is precisely on the crushing of corrugated cardboard. A series of laboratory experiments were conducted, in which the different types of single-walled corrugated cardboards were pressed in a fully controlled manner to check the impact of the crush on the basic material parameters. The amount of crushing (with a precision of 10 micrometers) was controlled by a precise FEMat device, for crushing the corrugated board in the range from 10 to 70 % of its original thickness. In this study, the influence of crushing on bending, twisting and shear stiffness as well as a residual thickness and edge crush resistance of corrugated board was investigated. Then, a procedure based on a numerical homogenization, taking into account a partial delamination in the corrugated layers to determine the degraded material stiffness was proposed. Finally, using the empirical-numerical method, a simplified calculation model of corrugated cardboard was derived, which satisfactorily reflects the experimental results.

Facade elements are known to represent a building component with multiple performance parameters to satisfy. Among others, “advanced facades” take advantage of hybrid solutions, like the assemblage of laminated materials. In addition to enhanced mechanical properties that are typical of optimally composed hybrid structural components, these systems are energy-efficient, durable, and offer lightening comfort and optimal thermal performance. This is the case of the structural solution developed in joint research efforts of the University of Zagreb and the University of Ljubljana, within the Croatian Science Foundation VETROLIGNUM project. The design concept involves the mechanical interaction of timber and glass load-bearing members, without sealing or bonded glass-to-timber surfaces. Laminated glass infilled timber frames are recognized as a new generation of structural members with relevant load-carrying capacity (and especially the enhancement of earthquake resistance of framed systems), but also energy-efficient and cost-effective solutions.

Tornadoes remain an active subject of observational and numerical research due to the damage and fatalities they cause worldwide as well as poor understanding of their behavior, such as what processes result in their genesis and what determines their longevity and morphology. A numerical model executed on a supercomputer run at high resolution can serve as a powerful tool for exploring the rapidly evolving tornado-scale features within a simulated storm, but saving large amounts data for meaningful analysis can result in unacceptably slow model performance, an unwieldy amount of saved data, and saved data spread across millions of files. In this paper, a system for efficiently saving and managing hundreds of terabytes of compressed model output is described in order to support a supercomputer simulation of a tornadic supercell thunderstorm. The challenges of managing a simulation spanning over a quarter trillion grid volumes across the Blue Waters supercomputer are also described. The simulated supercell produces a long-track EF5 tornado, and the near-tornado environment is described during tornadogenesis, where single upward-growing vortex undergoes several vortex mergers before transitioning into a multiple vortex tornado.

The goal of this lab is to look at how the characteristics of cementitious materials are affected by bending loads combined with dry and wet cycles of sulfate. In this paper, three sets of specimens with different water–cement ratios were designed. This study applied 20% and 40% of the ultimate bending load as a continuous bending load to the cementitious material specimens for a sulfate erosion test. It was discovered that the specimens' porosity, flexural strength, and compressive strength all tended to improve initially before declining as the cementitious material was degraded in the sulfate solution aged. The flexural strength of the cementitious materials declined as the bending load increased, and their internal sulfate ion concentration rose. A transport model of sulfate ions in cementitious materials under the coupling effect of bending load and sulfate erosion was created by combining the improved version of Fick’s second law and chemical reaction kinetics. The simulation results show that the ion transport properties of sulfate ions in cementitious materials are in accordance with the experimental laws. These research results formed the basis of the unified standards for the coupling of load dry and wet cycle systems, as well as evaluating the durability of cementitious materials under corrosive environments.

Rigid-hulled inflatable boats are extremely practical and popular nowadays. They offer a effective conciliation among usability and costs. Their stable and seaworthy behaviour is guaranteed by performing hydroplaning hulls coupled with unsinkable inflated tubes. At the same time, their design is often based on tradition and preconceptions. Rarely, the design assumptions are validated by the reality or, even, by deeper investigations. In this article, both numerical methods and experimental mechanics techniques are proposed as an essential way for supporting the designers in their decisive tasks. Three different situations are detailed where a numerical or an experimental approach shows its benefit inside the engineering design process: firstly permitting to investigate the behaviour of materials driving the fiberglass selection; then measuring the levels of stress and strain in the hull during sailing; finally, using all available information as a base for developing numerical models of the hull slamming in waves. Even if the discussion is focused on a rigid inflatable boat, large part of its considerations is relevant beyond this special case.

The treatment of critically ill patients remains an evolving and controversial issue. Mechanical circulatory support through a percutaneous approach for the management of cardiogenic shock has taken place in recent years. The combined use of IABP and Impella 2.5 device may have a role to play for this group of patients. A simulation approach may help with a quantitative as-sessment of the achievable degree of assistance. In this paper, we analyse the interaction be-tween Impella 2.5 pump applied as LVAD and IABP using the numerical simulator of the cardi-ovascular system developed in our laboratory. Starting with pathological conditions reproduced using literature data, the simulations were performed setting different rotational speeds for the LVAD and driving the IABP in full mode (1:1) or partial mode (1:2, 1:3 and 1:4). The effects in-duced by drug administration during the assistance were simulated too. The haemodynamic pa-rameters under investigation were: mean aortic pressure, systolic and diastolic aortic pressure, mean pulmonary arterial pressure, mean left and right atrial pressure, cardiac output, cardiac index, left and right ventricular end-systolic volume, left ventricular end-diastolic volume and mean coronary blood flow. The energetic variables considered in the study were: left and right ventricular external work and left and right atrial pressure-volume area. The outcome of our simulations shows that the combined use of IABP and Impella 2.5 achieves adequate support in the acute phase of cardiogenic shock compared to each standalone device. This would allow fur-ther stabilisation and transfer to a transplant centre should escalation of treatment be required.

In the southeastern coast of Brazil, the bays of Ilha Grande and Sepetiba are linked by the Ilha Grande Channel, where remarkably vigorous currents have been consistently observed. The sheer intensity of these currents defies a simple explanation through tidal forcing alone, prompting researchers to delve into potential influences such as basin resonance and the baroclinic effect. This study aims to elucidate the role of remote meteorological effects within this complex hydrodynamic system. A numerical approach with a coastal model nested within an ocean model was employed, enabling an in-depth examination of the intricate interplay between meteorological and tidal forcings. The study revealed a significant finding: the lag in signal propagation plays a pivotal role in determining how these signals impact the dynamics of the bays. The astronomical signal exhibits a minimal lag along the coast (1 minute), and leads to water level differences between the sea and the coastline, resulting in the generation of tidal currents at the bay entrances. On the other hand, the remote meteorological signal, with a stronger signal lag along the coast (4.92 hours), leads to the creation of water level difference between the bay’s entrances, inducing significant fluxes along the narrow Ilha Grande Channel.

Polydimethylsiloxane (PDMS) is one of the most popular elastomers and has been used in different fields, especially in biomechanics research. Among the many interesting features of this material, its hyperelastic behaviour stands out, which allows the use of PDMS in various applications, like the ones that mimic soft tissues. However, the hyperelastic behaviour is not linear and needs detailed analysis, especially the characterization of shear strain. In this work, two approaches, numerical and experimental, were proposed to characterize the effect of shear strain on PDMS. The experimental method was implemented as a simple shear testing associated with 3D digital image correlation and was made using two specimens with two thicknesses of PDMS (2 and 4 mm). A finite element software was used to implement the numerical simulations, in which four different simulations using the Mooney-Rivlin, Yeoh, Gent, and Polynomial hyperelastic constitutive models were performed. These approaches showed that the maximum value of shear strain occurred in the central region of the PDMS, and higher values emerged for the 2 mm PDMS thickness. Qualitatively, in the central area of the specimen, the numerical and experimental results have similar behaviours and the values of shear strain are close. For higher values of displacement and thicknesses, the numerical simulation results move further away from experimental values.

Fractional differential mathematical model unfolding the dynamics of the COVID-19 pandemic in India is presented and explored in this paper. The purpose of this study is to estimate the future outbreak of disease and potential control strategies using mathematical models in India as a whole country as well as in some of the states of the country. This model is calibrated based on reported cases of infections over the month of April 2020 in India. We have used iterative fractional complex transform method to find approximate solutions of the model having modified Riemann Liouville fractional differential operator. We have also carried out a comparative analysis between actual and estimated cumulative cases graphically, moreover, most sensitive parameters for basic reproduction number$(R_0)$ are computed and their effect on transmission dynamics of COVID-19 pandemic is investigated in detail.

The objective of this study, which is divided into two parts, is twofold: to address long standing challenges in the sensing of atmospheric turbulence-induced wavefront aberrations in strong scintillation conditions via comparative analysis of several basic scintillation resistant wavefront sensing (SR-WFS) architectures and iterative phase retrieval (IPR) techniques (Part I, this paper), and to develop a framework for the potential integration of SR-WFS techniques into practical closed-loop non-astronomical atmospheric adaptive optics (AO) systems (Part II). In this paper we consider basic SR-WFS mathematical models and phase retrieval algorithms, tradeoffs in sensor design and phase retrieval technique implementation, and methodologies for WFS parameter optimization and performance assessment. The analysis is based on wave-optics numerical simulations imitating realistic turbulence-induced phase aberrations and intensity scintillations, and optical field propagation inside SR-WFSs. Several potential issues important for practical implementation of SR-WFS and IPR techniques such as requirements for phase retrieval computational grid resolution, tolerance with respect to optical element misalignments, and the impact of camera noise and input light non-monochromaticity are also considered. Results demonstrate that major wavefront sensing requirements desirable for AO operation in strong intensity scintillations can potentially be achieved by transitioning to novel SR-WFS architectures based on iterative phase retrieval techniques.

This study presents the complexity and sensitivity of chaotic system dynamics in the case of the double pendulum. It applied detailed numerical analyses of the double pendulum in multiple computing platforms in order to demonstrate the complexity in behavior of the system of double pendulums. The equations of motion were derived from the Euler-Lagrange formalism, in order to capture the system's dynamics, which is coupled nonlinearly. These were solved numerically using the efficient Runge-Kutta-Fehlberg method, implemented in Python, R, GNU Octave, and Julia, while runtimes and memory usage were extensively benchmarked across these environments. Time series analyses, including the calculation of Shannon entropy and the Kolmogorov-Smirnov test, quantified the system's unpredictability and sensitivity to infinitesimal perturbations of the initial conditions. Phase space diagrams illustrated the intricate trajectories and strange attractors, as further confirmation of the chaotic nature of the double pendulum. All the findings have a clear indication of the importance of accurate measurements of the initial condition in a chaotic system, contributing to an increased understanding of nonlinear dynamics. Future research directions are faster simulations using Numba and GPU computing, stochastic effects, chaotic synchronization, and applications in climate modeling. This work will be useful for understanding chaos theory and efficient computational approaches in complex systems of dynamical nature.

In the case of solid slabs made of reinforced concrete that are usually subjected to bending, large areas of the structure are stressed well below their load-bearing capacity or remain stress-free. Contrary to this are shell structures, which can bridge large spans with little material if designed well. To improve the efficiency of ceiling slabs, we want to utilize the shell load-bearing behaviour on a smaller scale by dissolving the solid interior accordingly. In order to be able to study a wide range of such constructions virtually, a parametric multiobjective simulation environment is to be developed in an ongoing research project, basic analysis approaches of which are presented in this paper. In addition to the basic workflow and the programs used, the material models used, and their calibration are described on the basis of tests on textile reinforced concrete (TRC) samples. Initial tests on two individual TRC served to verify the model.

The CMT (Cold Metal Transfer) arc welding process is a convenient instrument for the assembly of thin sheets [1], [2]. More particularly, it permits the decrease of the amount of heat transferred to the parts to-be assembled, thus reducing their subsequent deformations. The present work aims at simulating the CMT welding of thin stainless-steel sheets in order to develop an approach that allows the prediction of temperature fields, as well as final deformations induced by the welding process. For that purpose, instrumented tests and numerical simulations were set aiming at comparing the experiments with simulations. Butt-welding of stainless-steel sheets was considered, with a thickness ranging from 1 to 1.2 mm. The weld seam samples were observed in order to set an equivalent heat source for each configuration. Moreover, the electric current and voltage were surveyed, and temperature measurements were performed using K-type thermocouples. In addition, displacement measurements were obtained using the DIC (Digital Image Correlation) technique. Thermomechanical simulations were then carried out using an equivalent heat source approach, considering the phase changes of elements, i.e. the transitions from solid to liquid and from liquid to solid. These simulations also consider the actual geometry of seams induced by addition of a filler material.

This study develops a new definition of fractional derivative that mixes the definitions of fractional derivatives with singular and non-singular kernels. Such developed definition encompasses many types of fractional derivatives, such as the Riemann-Liouville and Caputo fractional derivatives for singular kernel type as well as the Caputo-Fabrizio, the Atangana-Baleanu and the generalized Hattaf fractional derivatives for non-singular kernel type. The associate fractional integral of the new mixed fractional derivative is rigorously introduced. Furthermore, newly numerical scheme is developed to approximate the solutions of a class of fractional differential equations (FDEs) involving the mixed fractional derivative. Finally, an application to computational biology is presented.

An investigation of compressible flow over two-dimensional obstacles is presented in this paper. When shock waves are formed on surfaces due to compressibility and these shocks interfere with the boundary layer, undesirable effects such as friction, separation, and flow instability occur. To weaken the shock and reduce its effects, various methods have been employed in the past, including surface suction, surface blowing, and vortex generators. Using numerical solutions, the present work attempts to reduce the negative effects of the shock generated by the obstacle by creating porosity on its surface. Numerical methods such as the finite volume method and the Navier-Stokes equations as well as the Spalart-Allmaras model are used. By creating suction and blowing and increasing the cross-sectional area of the flow, porous surfaces reduce the effects of shock. Achieving around 50% porosity on the obstacle weakened the shock and reduced the Mach number after it, according to this paper's results. Also, the area under the skin friction diagram has decreased by about 38% as a result of less interference between the shock and the boundary layer and blowing caused by the porous surface.

Controlling injection parameters is paramount when it comes to producing high-quality green parts using powder injection molding. This work combines experimental and numerical approaches to study the impact of injection parameters on mold in-cavity pressure and on the overall quality of green parts produced by low-pressure powder injection molding. The properties of two low-viscosity feedstocks (formulated from a water-atomized stainless-steel powder and wax-based binder system) were measured and implemented in an Autodesk Moldflow numerical model to quantify the molding pressures, which were finally validated using experimental real-scale injections. The results confirmed that an increase in mold temperature, an increase in feedstock temperature, and a decrease in solid loading decrease the mold in-cavity pressure, which was correlated with the feedstock viscosity. As a key result, real-scale injections confirmed that a minimum flow rate was required to avoid atypical high in-cavity pressure leading in several visual defects such as weld lines, flow marks, cracks, sinks, and incomplete filling. Due to differences in its thermal transfer properties, this flow rate threshold value decreases as the feedstock solid loading increases. For injection speeds higher than this value, the injection pressure measured experimentally was linearly correlated with the injection flow rate.

This work focuses on the research area of energy generation and harvesting for its transformation into electrical energy with the primary use of energy independent sensor systems in the power range P=10-10000W. These systems are applied in sensing quantities in the transport sector (bridge structures, transport infrastructure, and the others ). The proposed theoretical harvester models describing the transformation of motion energy into electrical energy, also provides theoretical and experimental models. Results obtained in the design and construction of a robust motion generator with primarily linear geometry system technology are presented. The expected output electrical power of the harvester is variable and is designed based on the linear motion generated by the engine- compressed air, small fuel system, etc. The fundamental design of the generator core has been continuously numerically modeled and an experimental setup has been developed to analyze specific parts and variations in order to validate the concept and achieve the most suitable parameters with the selected construction materials. A scaled down version of the model principle was tested in experiments and then the parameters and results were compared with the predicted theoretical analyses.

This paper presents a numerical method for solving a two-dimensional subdiffusion equation with a Caputo fractional derivative. The problem considered assumes symmetry in both the equation’s solution domain and the boundary conditions, allowing for a reduction of the two-dimensional equation to a one-dimensional one. The proposed method is an extension of the fractional Crank-Nicolson method, based on the discretization of the equivalent integral-differential equation. To validate the method, the obtained results were compared with a solution obtained through Laplace transform. The analytical solution in the image of the Laplace transform was inverted using the Gaver-Wynn-Rho algorithm implemented in the specialized mathematical computing environment, Wolfram Mathematica. The results clearly show the mutual convergence of the solutions obtained by the two methods.

In recent years discrete element method (DEM) has gradually been applied to the traditional fluidization simulation of fine particles in micro fluidized bed (MFB). The application of DEM in simulating fast fluidization of fine particles in MFB has not yet received attention. This article presents a drag model that relies on the surrounding environment of particles, namely particle circumstance-dependent drag modle or PCDD model. Fast fluidization in MFB of fine particles is simulated using DEM based on the PCDD model. It is found that the gas-solid two-phase flow in MFB meets the common law of fast fluidization in circulating fluidized bed (CFB) to a certain extent, and also presents a special law that is significantly different from that in CFB. Simulations indicate that the local structure in MFB exhibits particle aggregation which is a natural property of fast fluidized, forming a structure where continuous dilute phase and dispersed concentrated phase coexist. The formation and fragmentation of particle clusters in different local regions of the bed have time synchronization. There exists strong effect of solid back-mixing in MFB, leading to relatively low outlet solid flux. The gas back-mixing effect is, however, not so distinct. The axial porosity shows a monotonically increasing distribution with the bed height, but does not strictly follow the single exponential distribution. The solid volume fraction at the bottom of the bed is significantly lower than the correlated value in CFB. The axial heterogeneous distribution of the cross-sectional average porosity in the lower half of the bed is also weakened. The radial porosity shows a distribution pattern of higher in the central region and lower in the sidewall region. Compared with the correlation results in CFB, the porosity near the central region in MFB is relatively low, while the porosity near the sidewall region is relatively high. The geometric size of the container, especially the radial size, is much smaller than that of a CFB. The relative area of contact between the MFB wall and particles is larger, and the wall friction factor becomes more significant. This may be the main reason for the time synchronization of particle agglomeration, severe particle back-mixing, low outlet solid flux, monotonically increasing axial porosity and weak core-annular structure of radial porosity.

Nowadays, there are implemented devices whose purpose is to perform massive computations by saving resources at the time they reduce the latency of arithmetic operations. These devices are usually GPUs, FPGAs and other specialised devices such as "Coral". Neural networks, digital filters and numerical simulators take advantage of the massively parallel operations of such devices. One way to reduce the amount of resources used is to limit the size of the registers that store data. This has led to the proliferation of numeric formats with a length of less than 32 bits, known as short floating point or SFP. We have developed several SFP’s for use in our neural network accelerator design, allowing for different levels of accuracy. We use a 16-bit format for data transfer and different formats can be used simultaneously for internal operations. The internal operations can be performed in 16-bit, 20-bit and 24-bit. The use of registers larger than 16-bit allows the preservation of fractional information while increasing precision. By leveraging some of the FPGA’s arithmetic resources, our design outperforms designs implemented from scratch and is competitive with specialized arithmetic circuits already implemented in the FPGA.

The amplified Arctic warming is one of several factors influencing atmospheric dynamics. In this work, we consider a series of numerical experiments to identify the direct role of the Arctic sea ice reduction process in forming climatic trends in the northern hemisphere. Aimed at this, we used two more or less independent mechanisms of ice reduction. The first is traditionally associated with increasing the concentration of carbon dioxide in the atmosphere from the historic level of 360 ppm to 450 ppm and 600 ppm. This growth increases air temperature and decreases the ice volume. The second mechanism is associated with a reduction in the reflectivity of ice and snow. We assume that comparing the results of these two experiments allows us to judge the direct role of ice reduction. The most prominent consequences of ice reduction, as a result, were the weakening of temperature gradient at the tropopause level in mid-latitudes, the slower zonal wind at 50-60∘N, intensification of wave activity in Europe, Western America, and Chukotka, and its weakening in the south of Siberia and Kazakhstan. We also consider how climate change may alter regimes such as blocking and stationary Rossby waves. The study used the INM-CM48 climate system model .

The need for quick and easy deflection calculations of various prefabricated slabs causes that simplified procedures and numerical tools are used more and more often. Modelling of full 3D finite element (FE) geometry of such plates is not only uneconomical but often requires the use of complex software and advanced numerical knowledge. Therefore, numerical homogenization is an excellent tool, which can be easily employed to simplify a model, especially when accurate modelling is not necessary. Homogenization allows for simplifying a computational model and replacing a complicated composite structure with a homogeneous plate. Here, a numerical homogenization method based on strain energy equivalence is derived. Using the method proposed, the structure of the prefabricated concrete slabs reinforced with steel spatial trusses is homogenized to a single plate element with an effective stiffness. There is a complete equivalence between the full 3D FE model built with solid elements combined with truss structural elements and the simplified homogenized plate FE model. The method allows for the correct homogenization of any complex composite structures made of both solid and structural elements, without the need to perform advanced numerical analyses. The only requirement is a correctly formulated stiffness matrix of a representative volume element (RVE) and appropriate formulation of the transformation between kinematic constrains on RVE boundary and generalized strains.

The adoption of Pump as Turbines (PATs) both in small scale hydroelectric plants and water supply systems has brought different advantages, the most recognized being cost-effectiveness as compared to other hydroturbines. However, due to their lack of flow control ability, their intolerance to off-design operations constitutes one tough shortfall. Moreover, this technology’s newness leads to PAT flow dynamics still being ununderstood even to date. Therefore, this study intends to numerically investigate the mixed flow PAT’s pump mode flow dynamics for five operating conditions expanding from optimum (1QBEP) to deep part-load (0.41 QBEP) conditions. Moreover the effect of runner blade angle on the same has been investigated where three angles namely -2°, 0°, and 2° have been considered. PAT flow stability was found to deteriorate as the flow decreased, where associated pressure pulsation level worsened at different flow zones. In addition, the blade angle increase led correspondingly increasing flow unsteadiness and pressure pulsation levels, where the pulsation frequencies from rotor-stator interactions were dominant for most of flow zones. This study’s findings are of a crucial importance to both scientific and engineering communities as they contribute to thorough understanding of PAT flow dynamics.

While the knowledge about the development of understanding positive integers is rapidly growing, the development of understanding zero is not well-known. Here we tested several components of preschoolers’ understanding zero: whether they can use empty sets in numerical tasks, whether they can use empty sets soon after they understand the cardinality principle, whether they know what the word “zero” refers to, and whether they categorize zero as a number. The results show that preschoolers can handle empty sets in numerical tasks as soon as they understand the cardinality principle or even earlier, and some of them know that these sets are labeled as “zero.” However, they are unsure whether zero is a number. These results identify three components of knowledge about zero: operational knowledge, linguistic knowledge, and meta knowledge. To account for these results we propose that preschoolers might understand numbers as the properties of items or objects in a set. In this view, zero cannot be a number, because an empty set does not include any items, and the missing items cannot have any property, excluding also the number property. This model might explain why zero is handled correctly in numerical tasks, while it is not regarded to be a number.

This article is devoted to Feller's diffusion equation which arises naturally in probabilities and physics (e.g. wave turbulence theory). If discretized naively, this equation may represent serious numerical difficulties since the diffusion coefficient is practically unbounded and most of its solutions are weakly divergent at the origin. In order to overcome these difficulties we reformulate this equation using some ideas from the Lagrangian fluid mechanics. This allows us to obtain a numerical scheme with a rather generous stability condition. Finally, the algorithm admits an elegant implementation and the corresponding Matlab code is provided with this article under an open source license.

The Lower Rio Grande Valley, South Texas is considered one of the more vulnerable coastal areas to flooding related with abrupt climate changes. From 1980-2017, there were 7 flooding events, 57 severe storm events, and 8 tropical cyclone events with losses exceeding $1 billion in the State of Texas, according to NOAA NCEI. Coastal flooding is typically a result of storm surge and heavy rainfall produced by hurricanes and tropical storms. In this study, the two-dimensional hydrodynamic flow circulation model is developed to predict the Lower Rio Grande Valley coastal area inundation due to the hurricane storm surge, especially in the case of Hurricane Beulah, 1967. The tropical cyclone properties and tidal constituents were assigned to the updated watershed geographic information with the bottom bathymetric and roughness data. For model validation, the Hurricane Dolly 2008 storm surge due to Hurricane Beulah at the coast and the storm surge reaches up to approximately 40 kilometers west from the coast through a natural river channel. This model can be used for a reliable engineering tool for the coastal hazard emergency management and disaster mitigation.

Non steady applied magnetic field impact on a liquid metals has good prospects for industry. For a better understanding of heat and mass transfer processes under these circumstances, numerical simulations are needed. A combination of finite elements and volumes methods was used to calculate the flow and solidification of liquid metal under electromagnetic influence. Validation of numerical results was carried out by means of measuring with ultrasound Doppler velocimetry technique, as well as with neutron radiography snapshots of the position and shape of the solid/liquid interface. As a result of the first part of the work, a numerical model of electromagnetic stirring and solidification was developed and validated. This model could be an effective tool for analyzing the electromagnetic stirring during the solidification process. In the second part, the dependences of the velocity pulsation amplitude and the melt velocity maximum value on the magnetic field pulsation frequency are obtained. It was found numerically the ability of the pulsating force action to develop higher values of the liquid metal velocity at a frequency close to the MHD resonance. Obtained characteristics give a more detailed description of the electrically conductive liquid behaviour under action of pulsating traveling magnetic field.

The properties of iterative splitting methods with serial versions have been analyzed since recent years, see [1] and [3]. We extend the iterative splitting methods to a class of parallel versions, which allow to reduce the computational time and keep the bene t of the higher accuracy with each iterative step. Parallel splitting methods are nowadays important to solve large problems, which can be splitted in subproblems and computed independently with the dierent processors. We present a novel parallel iterative splitting method, which is based on the multi-splitting methods, see [2], [10] and [15]. Such a exibilisation with multisplitting methods allow to decompose large iterative splitting methods and recover the bene t of their underlying waveform-relaxation (WR) methods. We discuss the convergence results of the parallel iterative splitting methods, while we could reformulate such an error to a summation of the individual WR methods. We discuss the numerical convergence of the serial and parallel iterative splitting methods and present dierent numerical applications to validate the bene t of the parallel versions.

From June 18 to 19, 2013, the Ésera river in the Pyrenees, Northern Spain, caused widespread damage due to flooding as a result of torrential rains and sustained snowmelt. We estimate the contribution of snow melt to total discharge applying a snow energy balance to the catchment. Precipitation is derived from sparse local measurements and the WRF-ARW model over three nested domains, down to a grid cell size of 2 km. Temperature profiles, precipitation and precipitation gradient are well simulated, although with a possible displacement regarding the observations. Snowpack melting was correctly reproduced and verified in three instrumented sites, and according to satellite images. We found that the hydrological simulations agree well with measured discharge. Snowmelt represented 33% of total runoff during the main flood event and 23% at peak flow. The snow energy balance model indicates that most of the energy for snow melt during the day of maximum precipitation came from turbulent fluxes. This approach forecast correctly peak flow and discharge during normal conditions at least 24h in advance and could give an early warning of the extreme event 2.5 days before.

Recently, Indium Tin Oxide, a highly transparent, well conductive, and CMOS-compatible material, has been paying strong attention to the thermo-optic controlled silicon photonics industry because it allows a miniature of the gap between the core silicon and the heater, thus enabling reducing the electric power consumption and enhancing the switching speed. In this article, we propose an ultralow loss and small-size ITO microheater for the phase shift tuning. The designated microheater is manipulated in realizing a numerical co-design of compact and high bandwidth three-mode converter and three-mode selective router. Simulation results illustrate the 3-dB bandwidth for the three-mode converter and three-mode selective router as much as 100-nm and 40-nm during crosstalk under -25 dB, respectively. Besides, co-designed devices attain relatively large fabrication tolerances corresponding to width and height tolerances of ±50 nm and ±5 nm. In addition, the proposed devices consumed less than 90 mW total power consumption and took a fast switching time below 8 μs. Moreover, both two co-designs can be integrated into an estimated compact footprint of 8 μm2160 μm. Such excellent performances demonstrate the attractive potential of ITO as low-loss thermo-optic phase shifters and open an alternative way for enabling ultrafast and high-speed mode division multiplexing systems and very large-scale photonic integrated circuits.

When the formation flying consists of satellites that are independent from each other and forms a virtual synthetic aperture telescope that replaces a single large telescope with all of its optical elements it is required mutual coordination between the satellites with high accuracy in order to achieve good optical observations. In this paper we consider the problem of developing a control system for a tetrahedral satellite formation flying representing a synthetic aperture telescope in the geostationary orbit for high resolution monitoring of fire in the forest area in infrared spectrum. Synthesizing the image with good quality requires to keep the configuration of formation with µm-class accuracy. Study of dynamics of passive uncontrolled motion of formation flying showed a significant deviation of the configuration from the required shape with a high frequency due to the action of gravitational forces. To keep the configuration in the required form with µm accuracy the analysis of efficiency of various controllers was carried out in the process of numerical simulation. The simulation results made it possible to highlight the features of using various approaches to the development of control system for the satellite formation flying representing a synthetic aperture telescope.

As long as the non-contact digital printing is not a common standard in the corrugated packaging industry, corrugated board crushing is a real issue that affects the load capacity of the boxes. Crushing mainly occurs during the converting of corrugated board (e.g. analog flexographic printing or laminating) and is a process that cannot be avoided. However, as show in this study, it can be controlled. In this work, extended laboratory tests were carried out on the crushing of double-walled corrugated board. The influence of fully controlled crushing (with a precision: ±10 μm) in the range from 10 to 70 % on different laboratory measurements was checked. Most of the typical mechanical tests were performed e.g. edge crush test, four-point bending test, shear stiffness test, torsional stiffness test, etc. on reference and crushed specimens. The residual thickness reduction of the crushed samples was also controlled. All empirical observations and performed measurements were the basis for building an analytical model of crushed corrugated board. The proven and verified model was then used to study the crushing effect of the selected corrugated board on the efficiency of simple packages with various dimensions.

This work is concerned with the existence and uniqueness of boundary value problems defined on semi-infinite intervals. These kinds of problems seldom admit exactly known solutions and, therefore, the theoretical information on their well-posedness is essential before attempting to derive an approximate solution by analytical or numerical means. Our utmost contribution in this context is the definition of a numerical test for investigating the existence and uniqueness of solutions of boundary problems defined on semi-infinite intervals. The main result is given by a theorem relating the existence and uniqueness question to the number of real zeros of a function implicitly defined within the formulation of the iterative transformation method. As a consequence, we can investigate the existence and uniqueness of solutions by studying the behaviour of that function. Within such a context the numerical test is illustrated by two examples where we find meaningful numerical results.

This paper presents an original method of additive manufacturing of cylindrical parts with variable circumference thickness, which allows the control of the deposition of molten material using an algorithm for decomposing the part geometry into volumetric elements with known dimensional configuration. In the absence of a post-processor capable of controlling additive manufacturing on a 5-axis numerical control machine, control of the deposition of molten material is done using parameterized programs, which can control both the feed speeds of the machine tool axes and the specific functions of the printing equipment. Additive manufacturing can make a positive contribution to sustainable development compared to traditional manufacturing technologies, thus making a positive contribution for a sustainable future. The aim of the work is to make it possible to 3D print parts with variable wall thickness using a CNC machining centre. To obtain the variable thickness layer we have implemented an original method of deposition with molten material (FDM), the coordination of the system composed of physical elements respectively programmable elements, is realized through control functions materialized in parameterized part programs, the generated outputs being the variable speed of the machine axes on a circular trajectory, the angular positioning, the filament advance.

This review is devoted to present the history of CARDIOSIM© software simulator platform, which was developed in Italy to simulate the human cardiovascular and respiratory system. The first version of CARDIOSIM© was developed at the Institute of Biomedical Technologies of the National Research Council in Rome. The first platform version published in 1991 ran on PC with disk operating system (MS-DOS) and was developed using the Turbo Basic language. The last version runs on PC with Microsoft Windows 10 operating system; it is implemented in Visual Basic and C++ languages. The platform has a modular structure consisting of seven different general sections, which can be assembled to reproduce different pathophysiological conditions. The software simulator can reproduce the most important circulatory phenomena in terms of pressure and volume relationships. It represents the whole circulation using a lumped-parameter model and enables the simulation of different cardiovascular conditions according to Starling’s law of the heart and a modified time-varying elastance model. Different mechanical ventilatory and circulatory devices have been implemented in the platform including thoracic artificial lung, ECMO, IABP, pulsatile and continuous right and left ventricular assist devices, biventricular pacemaker and biventricular assist devices. CARDIOSIM© is used in clinical and educational environment.

This paper is concerned with developing an efficient numerical algorithm for fast implementation of the sparse grid method for computing the $d$-dimensional integral of a given function. The new algorithm, called the MDI-SG ({\em multilevel dimension iteration sparse grid}) method, implements the sparse grid method based on a dimension iteration/reduction procedure, it does not need to store the integration points, nor does it compute the function values independently at each integration point, instead, it reuses the computation for function evaluations as much as possible by performing the function evaluations at all integration points in a cluster and iteratively along coordinate directions. It is shown numerically that the computational complexity (in terms of CPU time) of the proposed MDI-SG method is of polynomial order $O(Nd^3 )$ or better, compared to the exponential order $O(N(\log N)^{d-1})$ for the standard sparse grid method, where $N$ denotes the maximum number of integration points in each coordinate direction. As a result, the proposed MDI-SG method effectively circumvents the curse of dimensionality suffered by the standard sparse grid method for high-dimensional numerical integration.

This paper proposes a lightweight joint with bamboo culm cross connection, which is constructed by screwing one side of the screw into the other side of the wooden plug, its simple construction makes it easy to manufacture and cost-effective. This form connects adjacent bamboo culms to form corner joints, and bolt connects adjacent bamboo culm frames to form edge joints, to explore the mechanical properties of the combination joints formed by corner joints and edge joints, by combining experiments and numerical simulations, the method discovered and explained the relationship and mechanism between the number and position of bolts and the stiffness of edge joints. A calculation model for frame-unit bamboo culm members considering semi-stiffness of joints is proposed, and the conversion equations between linear stiffness of corner and edge joint and their rotational stiffnesses are derived. By establishing the series and parallel relationship between the corner and edge joints in the assembled members, a generalized relational equation between the total stiffness of the assembled joint and the stiffness of the corner and edge joints is derived. A numerical simulation method for frame-unit bamboo culm members with semi-rigid joints is proposed, which can obtain the stiffness calculation formula of edge joints and the average rotational stiffness value of semi-rigid corner joints. A finite element analysis method based on semi-rigid joints is proposed for frame-unit bamboo culm members, and the internal force sketches and calculation methods for bamboo culms and joints are presented, which can be used for the internal force analysis and design of frame-unit bamboo culm lattice structures.

This paper introduces a novel multi-strategy enhanced dung beetle optimization (MSDBO) algorithm that is designed to address several issues identified in the standard dung beetle optimization algorithm. Specifically, the MSDBO aims to enhance convergence speed, reduce susceptibility to local optima, and increase search accuracy. By incorporating three strategies: tent chaotic mapping for population initialization, the golden sinusoidal strategy for position updating, and the Lévy flight strategy for balancing exploration and exploitation, the standard dung beetle optimization algorithm is enhanced. The MSDBO algorithm is evaluated using twelve benchmark test functions and compared against five state-of-the-art algorithms. The results consistently show that MSDBO exhibits faster convergence speeds and more accurate solutions than the other algorithms across most of the test functions. In addition, MSDBO is also applied to optimize the parameters of a valve plate, including the close angle, cross angle, triangle groove sizes, and wrap angle. The optimization outcomes reveal that MSDBO effectively minimizes pressure ripples in the piston chamber, resulting in reduced flow rate fluctuations and noise emission compared to the initial design. This study highlights the potential of the MSDBO algorithm in tackling complex nonlinear engineering optimization problems.

The first paper of this two-part series paper discussed the development of a novel lightweight 3D wood dowel-reinforced glass epoxy hybrid composite material (3DdrFRP) and its manufacturing procedures. It also experimentally compared the performance of scaled utility poles made from conventional 2D E-glass epoxy and 3DdrFRP materials. In the second part, we developed robust finite element (FE) models in LS-DYNA, calibrated them based on experimental results, and used them to simulate the performance of equivalent 2D and 3D poles, proving the integrity of the numerical model. Additionally, we developed a simplified analytical calculation method for engi-neers to determine the stiffness of 3D-DrFRP poles accurately and quickly.

Microscale laser dynamic forming, as a novel high-speed microforming technique, can overcome the shortcomings of traditional microforming methods. However, in practical applications, laser dynamic microforming technology is often affected by the rebound behavior of the workpiece surface, limiting the further improvement of processing quality and efficiency. This paper aims to reduce the rebound effect in laser dynamic microforming by using multi-pulse laser shock loading. The forming results of workpieces under different laser energies and laser impact numbers were studied using experimental and numerical simulation methods. Numerical simulations of the forming results after multiple laser shocks were conducted using ANSYS/LS-DYNA software. These numerical simulation results were then experimentally validated and compared. Surface morphology and microstructure of the workpieces were characterized using a confocal microscope and scanning electron microscope, and energy dispersive spectroscopy (EDS) was used to analyze the chemical element content changes in the collision regions at the bottoms of the workpieces after multi-pulse loading, revealing the collision behavior patterns during the forming process. Finally, the forming laws of workpieces under multiple laser shocks were summarized.

The theory says that number interacts with spaces based on the meaning of mathematics, in this way it is possible to obtain numerical knowledge. The theory shows the possibility of using spaces related to each other to efficiently discover whether results and origins are even or odd, but always applying rules to make this work. the study uses equivalent representations of odd and even numbers. Thus, it is possible to discover the possibilities of origins and their results.

Wireline Formation Testing is an important technique in the oil field of exploration and development. Not only it can make real fluid samples of the formation directly obtained to know exactly oil existed in formation or not; but it can also show flowing pressure change to see the production capacity of the formation. So it is important measurement for formation evaluation during the drilling process and supports for activities of the exploration and development in the oil field. A numerical simulation model in this article is researched and established based on the Finite Volume Method with considering the influence of sensitive parameters such as reservoir heterogeneity, probe suction area, and mud-filtrate invasion depth during the drilling. The model is capable to design and evaluate for formation fluid sampling operations with calculating hydrocarbon content and flowing pressure. Furthermore, through case application, the performance and effect in the process of Wireline Formation Testing was demonstrated. The results indicate that this technology can be served as an effective auxiliary tool for fluid sampling operations with the function of optimizing fluid sampling measures. It can improve the accuracy of predicting indicators such as hydrocarbon content and breakthrough time during the sampling process. This study provides important backups and technical guidance for professionals in geological exploration and oilfield development.

Nuclear fusion reactors are composed by several complex components whose behaviour may be not certain a priori. This uncertainty may have a significant importance in the evolution of fault transients in the machine, causing unexpected damages to its components. For this reason a suitable method for the uncertainty propagation during those transient is required. The Monte Carlo method would be the reference option, but it is, in most of the cases, not applicable due to the large amount of required simulations to be repeated. In this context the Polynomial Chaos Expansion has been considered as a valuable alternative. It allows to create a surrogate model of the original one in terms of orthogonal polynomials. Then, the uncertainty quantification is performed repeatedly calling this much simpler and faster model. Using the fast current discharge in the Divertor Tokamak Test Toroidal Field (DTT TF) coils as a reference scenario, this method has been applied: the uncertainty on the parameters of the Fast Discharge Unit (FDU) varistor disks is propagated to the simulated electrical and electro-magnetic relevant effects. Eventually two worst case scenarios have been analyzed from the thermal-hydraulic point of view with the 4C code, simulating a fast current discharge as a consequence of a coil quench. Eventually it has been demonstrated that the uncertainty on the inputs (varistor parameters) strongly propagates obtaining a wide range of possible scenarios in case of accidental transients. This result underlines the necessity to take into account and propagate all possible uncertainties in the design of a fusion reactor, according to the Best Estimate Plus Uncertainty approach.

The transportation of feed pellets via pneumatic conveying plays an improtant role in feed industry. In recent years, many efforts are made both exprimentally and numerically to gain a better understanding of the underlying mechanism for pneumatic conveying. Though few of those research is directly related to feed pellets, it can be beneficial to draw a full picture of rencent development in pneumatic conveying, with emphasis on aspects extendable to feed transportation. This paper reviews first the major factors concerning feed pellets pneumatic conveying, such as particle breakage, pipe wear and electrostatic. Building on that, new advancement including emerging new technologies in experiments and simulations are discussed, with a focus on the experimental measurements and mathematical models, repectively. The needs for future research and the analogy to feed pellets tranportation is given lastly.

A solution for the Prandtl-Blasius equation is essential to all kinds of boundary layer problems. This paper revisits this classic problem and presents a general Maple code as its numerical solution. The solutions were obtained from the Maple code, using the Runge-Kutta method. The study also considers convergence radius expanding and an approximate analytic solution is proposed by curve fitting. Similarly, the study resolves some boundary layer related problems and provide relevant Maple codes for these.

Advancement in physics often results from analyzing numerical data and then creating a theoretical model that can explain and predict those data. In the field of lens design, the reverse is true: longstanding theoretical understanding is being overtaken by more powerful numerical methods.

A microstructure-based model is developed to study the effective anisotropic properties (magnetic, dielectric or thermal) of two phase particle-filled composites. The Green’s function technique and the effective field method are used to derive theoretically the homogenized (averaged) properties for a representative volume element containing isolated inclusion and an infinite, chain-structured particles. Those results are compared with the FE approximations conducted for the assumed representative volume element. In addition, as a special case, the Maxwell–Garnett model is retrieved when particle interactions are not taken into consideration. We shall also give some information on the optimal design of the effective anisotropic properties taking into account the shape of magnetic particles.

Marine cold air outbreaks (MCAOs) are large-scale phenomena in which cold air masses are advected over open ocean. It is well-known that these events are linked to the formation of polar lows and other mesoscale phenomena associated with high wind speeds, and that they therefore in some cases represent a hazard to maritime activities. However, it is still unknown whether MCAOs are generally conducive to higher wind speeds than normal. Here this is investigated by comparing the behaviour of ocean surface wind speeds during MCAOs in three atmospheric reanalysis products with different horizontal grid spacings, along with case studies using a convection-permitting numerical weather prediction model. The study regions are the Labrador Sea and the Greenland–Iceland–Norwegian (GIN) Seas, where MCAOs have been shown to be important for air–sea interaction and deep water formation. The main findings are: 1) Wind speeds during the most extreme MCAO events are stronger than normal and higher than wind speeds during less severe events; 2) The peak times of MCAO usually occur when baroclinic waves pass over the regions; and 3) Reanalyses with grid spacings of more than 50 km appear to underestimate winds driven by the large ocean–atmosphere energy fluxes during MCAOs. It is also shown that while the strong wind episodes during MCAOs generally last for just a few days, MCAOs can persist for up to 50 days. These findings demonstrate that it would be worthwhile to forecast MCAOs, and that it might be possible to do this beyond the standard weather forecasting range of up to 10 days.

Promoting the use of solar energy resources has always faced the challenges of instability and supply-demand mismatch. The key to solving these issues is to efficiently store and utilize solar energy resources using high-performance heat storage devices. This study designed a high-performance shell-and-tube phase change thermal storage device and established a numerical model using ANSYS software to summarize the device's dynamic melting law. To verify the accuracy of the numerical simulation, a performance testing platform for the phase change thermal storage device was built to investigate the impact of factors such as inlet water temperature, inlet water flow rate, type of heat storage, and initial temperature of the device, and to reveal the change law of the device's performance. The results show that the inlet water temperature has the most significant impact on the device's heat storage and release performance. When the device's heat storage or release is used for heating, changing the inlet water flow rate has a weak and limited effect on the device's performance. However, when the device's heat release is used to provide domestic hot water, increasing the makeup water temperature and reducing the inlet water flow rate can significantly improve the device's effective heat release. Furthermore, based on the experimental validation of the model's correctness, this study further simulated and studied the impact of different factors on the device's heat storage process to optimize its structural design and provide technical references for the device's actual operation and installation. The results show that the placement of fins has a negligible effect on the performance of the heat storage device while reducing the fin spacing and increasing the fin thickness can significantly improve the melting efficiency of the phase change material (PCM). Additionally, the heat storage characteristics of the device are significantly better in the vertical installation mode than in the horizontal installation mode. This study provides theoretical guidance and technical references for the design and use of phase change thermal storage devices.

In the steeply inclined and extremely thick coal seams (SIETCS) mined using the horizontal sublevel top-coal caving (HSTCC) method, the uncertainty of gas emission is a safety threat to the mining operations. In order to reduce the occurrence of accidents, the determination of gas emission is crucial. In this paper, we first proposed a prediction model for workers at the floor coalbed to calculate gas emission on site. We then put forward a finite element numerical simulation for researchers to predict gas emission from the floor coalbed. At last, we measured gas emitted from the floor coalbed of SIETCS in Wudong Coal Mine in a specific mining period and used the data to verify the applicability and accuracy of these two gas-emission prediction methods. The results showed that the gas emission from Wudong Coal Mine was 1.08 m³/min calculated based on the prediction model and 1.07 m³/min obtained using the user-defined integration method. Both methods have their own advantages, disadvantages and applicable objects, and are important in predicting gas emission from SIETCS mined using HSTCC method.

In crank presses, an important role is played by the presence of actuators with dwell, in which, with continuous movement of the input links, the output working link remains stationary at some part of the work. The use of a high-class structural group (fourth class) expands the functionality of the crank press, including it can ensure the link dwell of the working link on a given section of movement during the required period of time. As a result of the conducted research, four variants of actuators of the crank knee press were designed. Due to the rational choice of the positions of racks and crosshead guide, the best layout of the dimensions of the press mechanism has been achieved, changing the coordinates of the racks accordingly allows to design a mechanism with upper or lower dwells of the working links. When synthesizing (selecting) parameters such as: l_2 and h, it is possible to obtain a height of different duration. All this is shown on the basis of a numerical experiment based on kinematic analysis. In addition, the complex structure of the mechanism makes it possible to ensure the exact link dwell, which cannot be achieved due to the well-known knee presses based on the second-class mechanism [21].

The paper is dedicated to the topical problem of examining permafrost state and the processes of its geocryological changes by means of geophysical methods. To monitor the cryolithozone, we propose and scientifically substantiate a new technique of pulsed electromagnetic cross-well sounding. Based on the vector finite-element method, we created a mathematical model of the cross-well sounding process with a pulsed source in a three-dimensional spatially heterogeneous medium. A high-performance parallel computing algorithm was developed and verified. Through realistic geoelectric models of permafrost with a talik under a highway, constructed following the results of electrotomography field data interpretation, we numerically simulated the pulsed sounding on the computing resources of the Siberian Supercomputer Center of SB RAS. The simulation results suggest the proposed system of pulsed electromagnetic cross-well monitoring to be characterized by a high sensitivity to the presence and dimensions of the talik. The devised approach can be oriented to addressing a wide range of issues related to monitoring permafrost rocks under civil and industrial facilities, buildings and constructions.

A mathematical model that comprehensively captures the real behavior of riverbed deformation, encompassing all pertinent effects, is developed. The underwater slope reformation process, with the generatrix aligned along the flow velocity in the model, is considered. A numerical model is introduced to calculate the flow involving a deformable bottom, and the model's validation is established through rigorous analysis of experimental findings. The research firmly confirms the suitability of the proposed mathematical and numerical model for describing deformations in uneven and unsteady river flows, including the movement of dredging slots and channel quarries. The model's minimal equation count and reliance on empirical constants demonstrate the model's efficiency. The model's predictions align strongly with experimental data, although optimal values of empirical coefficients vary slightly across different experiments. Hence, there is a call for further investigation to derive more universally applicable closure relationships for the model. The importance of validating the model with reliable field data and its potential extension to accommodate hydraulically diverse soils is emphasized. Such an extension is feasible due to the concentration transfer equation, enabling independent calculations for particle fractions of varying sizes as long as the total particle concentration in the stream remains within reasonable limits. This dedicated research contributes significantly to understanding riverbed deformations and advancing accurate modeling and management of riverine environments.

Experimental methodologies for fatigue lifetime prediction are time-intensive and susceptible to environmental variables. While the cohesive zone model is popular for predicting adhesive fatigue lifetime, entropy-based methods have also shown promise. This study aims to provide an understanding of the durability characteristics of CFRP adhesive joints by incorporating an entropy damage model within the context of the finite element method (FEM), examined the effects of different adhesive layer thicknesses on SLS models. As the adhesive layer increased in thickness, DAMAGE VARIABLES initially rose and then declined, peaking at 0.3mm. This finding provides crucial understanding into the stress behavior at the resin-CFRP interface and the resin's fatigue mechanisms.

With more and more transportation tunnels have been and will be constructed in loess areas in Northwest China with high earthquake potential, the overall stability of portal section under earthquakes actions and the related aseismic countermeasures attracted the attentions from both the scholars and engineers, especially the tunnels in the upper slope connecting the high bridges crossing rivers or valleys. In order to study the dynamic response characteristics and damage evolution of steep loess slope with a tunnel under the earthquake actions, a large-scale shaking table tests were performed on steep loess slope with a tunnel. Wenchuan-tangyu (WT) wave and El Centro (El) wave records were applied on the model to investigate the displacement response and acceleration response of loess slope with a tunnel under the horizontal (X) and the combined action of horizontal and vertical (X-Z) seismic loads, respectively. In particular, three-dimensional non-contact optical measurement techniques were used to obtain the slope surface displacements. The results showed that the main deformation pattern of the slope was horizontal movement and settlement when the seismic wave input was in the X and X-Z directions, respectively. However, the X direction seismic wave had a greater impact on the deformation of the slope, and the tunnel portal slope was destroyed under the action of a large horizontal seismic acceleration finally. Slope failure ahead of a tunnel could be divided into four stages, i.e. elastic deformation stage, plastic deformation accumulation stage, local failure stage, and overall failure stage. The peak ground displacement of X direction (PGDX) and peak ground displacement of Z direction (PGDZ) of the slope surface increased with the increasing of the input peak ground acceleration (PGA) when the input wave was same waveform and same direction. The existence of the tunnel had a great influence on the PGA and the PGA amplification factor (PGAAF) of the soil mass surrounding it. This was because the seismic waves encounter a tunnel surface with clear differences in the physical properties of the medium during their propagation in the slope, thereby forming a strong reflection and refraction effect, and the amplitude changed significantly. Numerical simulation results were basically consistent with the experimental results.

The objective of this study is to investigate the use of excavation behavior prediction and analysis software in the field of civil en-gineering. PLAXIS and SoilWorks, widely used in the engineering and academic communities, were employed as research tools for analyzing gravel layers and deriving appropriate ranges of soil elastic modulus for different software programs. By collecting excavation cases in the Xindian area of New Taipei City, Taiwan, and conducting deep excavation analysis using the displacement of retaining walls, this study provides recommended ranges for localized selection of soil elastic modulus. The suggested range for PLAXIS is 7,840 N/m² to 9,800 N/m², while Soil-Works suggests a range of 2,450 N/m² to 3,430 N/m². These ranges allow for reasonable estimation of maximum deformations during the final excavation stage. Based on the research findings, it is recommended that engineers refer to the provided ranges when selecting soil elastic modulus for excavation analysis in gravel layers using different soft-ware programs in the Xindian area of Taiwan to improve the accuracy of deformation predictions during the final excavation stage. These results serve as important references for engineers and contribute to the effective prediction and management of excavation behavior in civil engineering projects.

Creep is a fundamental property naturally exists in some types of rock, which is significant for the long-term stability of roadways during the mining process. In this paper, the long-term strength of coal and rock were obtained via laboratory experiments, and a Cvisc elasto-viscoplastic model was adopted and introduced in FLAC3D, based on the 3101 transport roadway in Hongqinghe Coal Mine, to investigate the influence of creep on the stability of deep-high stress roadway. The test results show that the long-term strength of 3-1 coal and sandy mudstone, respectively, is 18.65 MPa, 39.95 MPa. The plastic zone, the deformation, and the damage of roadway surrounding rock behave an obvious increase after being excavated for 720d as the creep model was chosen. The plastic zone failure with models shear-p (1090.7 m3), shear-n (381.7 m3), tension-n (98.4 m3), and tension-p (30.8 m3), the damage value has an obvious increment of increased 21.2% (0.053), the deformation increases in the order is two-sidewalls (1978 mm), roof (907 mm), floor (101 mm). The creep of the roadway can be divided into three stages: the accelerating stage, the decaying stage, and the stable stage. The creep speed of each stage is greatly affected by the presence or absence of anchor spray support: the creep speed of the bare roadway roof, roadway side, and floor stability, respectively, is 1.01, 1.02, and 0.12 mm/d; After anchor spray support, the creep velocity, correspondingly, decreased to 0.69, 0.37, and 0.12 mm/d, and the amount of surrounding rock damage decreased from 0.302 to 0.243. This indicates that the anchor spray support can significantly reduce the creep effect of the roadway. The Cvisc creep model was verified reliable and can provide guidance for deep high-stress coal roadway support.

The article presents a simplified method for determining the strength of a corrugated board packaging subjected to dynamic transport loads. The proposed algorithm consists of several calculation steps: (1) a static analysis of the compressive strength of the package, (2) an analysis of random vibrations in the frequency domain, used to determine the resonance frequencies, and (3) a dynamic analysis of the package loaded with computed resonant frequencies. For this purpose, numerical models of the static compression test of the packaging before and after the dynamic analysis of the package subjected to general transport loads were developed. In order to validate the model, the laboratory packaging compression tests were also performed for samples of boxes with 3-layer cardboard. Thanks to this, it was possible to verify the results of numerical simulations of compression tests for several box geometries. Which, in turn, allowed for the development of a method based on dynamic and post-dynamic (static) numerical analysis, allowing to determine with high accuracy the resistance of selected packaging to vibrations and dynamic loads. The results of the (validated experimentally) numerical analysis prove the usefulness of the simplified method presented here for precise estimation of the load capacity of various packages dynamically loaded during transport.

In engineering practice, one can often encounter issues related to optimization where the goal is to minimize material consumption, minimize stresses or deflections of the structure. In most cases, these issues are addressed with finite element analysis software and simple optimization algorithms. However, in the case of optimization of certain structures, it is not co straightforward. An example of such constructions are bubble deck ceilings, where in order to reduce the dead weight, air cavities are used, which are regularly arranged over the entire surface of the ceiling. In the case of these slabs, the flexural stiffness is not constant in all its cross-sections, which means that the use of structural finite elements (plate or shell) for static calculations is not possible, and therefore the optimization process becomes more difficult. The paper presents a minimization procedure of the weight of bubble deck slabs using numerical homogenization and sequential quadratic programming with constraints. Homogenization allows to determine the effective stiffnesses of the floor, which in the next step are sequentially corrected by changing the geometrical parameters of the floor and voids in order to achieve the assumed deflection. The presented procedure allows to minimize the use of material in a quick and effective way by automatically determining the optimal parameters describing the geometry of the bubble deck floor cross-section.

In order to study the effect of TiB2 particles on the mechanical properties of TiB2/6061Al composites, a series of TiB2/6061Al 3D representative volume element (RVE) were established based on SEM photos. This model took into account the ductile damage of the matrix and the traction separation behavior of the interface, and the linear damage evolution law was introduced to characterize the stiffness degradation behavior of the matrix elements. The mixed boundary conditions were used for RVE tensile experiments, and the accuracy of the predicted result was verified by the agreement of the experimental stress-strain curve. Results show that the addition of TiB2 particles can effectively promote the load-bearing capacity of the composite, but elongation is reduced. With the weight fraction of TiB2 increasing from 2.5% to 12.5%, the elastic modulus, yield strength, and tensile strength are increased by 8%, 10.37%, and 11.55% respectively, while the elongation decreased by 10%. The clustering rate of the TiB2 particles is also an important factor affecting the toughness of the composites. With the increase in the clustering rate of TiB2 particles from 20% to 80%, the load-bearing capacity of the composites is not improved, and the elongation of the composites is reduced by 8%. Moreover, the high strain region provides a fast expansion path for crack propagation and the particle spacing is a crucial factor that affects the stress field.

In this work, in spite of Milne’s recommendation using the three-point Newton–Cotes open formula (Milne’s rule) as a predictor rule and three-point Newton–Cotes closed formula (Simpson’s rule) as a corrector rule for 4-th differentiable functions with bounded derivatives. There is still a great need to introduce such formulas in other Lp spaces. Often, we need to approximate real integrals under the assumptions of the function involved. Because of that, the aim of this work is to introduce several Lp error estimates for the proposed perturbed Milne’s quadrature rule. Numerical experiments showing that our proposed quadrature rule is better than the classical Milne rule for certain types of functions are provided as well.

The shield tunnels inevitably endure various damage with the service time increasing. Meanwhile, steel corrugated plate has been used extensively in multiple conditions and proved effective to strengthen the segmental joints by full-scale tests. A numerical model is proposed to probe the feasibility of using new Stainless Steel Corrugated Plate (SSCP) to reinforce the shield tunnel segments. A new method, called virtual tracking element technology, is employed to achieve the simulation of realistic stress state of the segmental joint. Moreover, the segmental joint component analysis and parametric study are conducted based on the numerical model. The results demonstrate that: (1) the virtual tracking element technology proves valid and efficient to simulate the secondary stress state of segmental joint; (2) SSCP reinforcement is not fully utilized when the grade of segmental concrete is C50 and it has abundant safety margin for potential overload; (3) SSCP reinforcement is well-performed regardless of the burial depth and reinforcement in advance is recommended.

With the aim to improve cladding coating quality and prevent cracking, this paper established an extreme high-speed laser cladding thermo-mechanical coupling simulation model to study the evolution of the temperature field and residual stress distribution. Process parameters that impacted the macroscopic morphology of single-pass coatings were investigated. Numerical calculations and temperature field simulations were performed based on the process parameter data to validate the effect of the temperature gradient and cooling rate on the coating structure and the residual stress distribution. The results showed that a good coating quality could be achieved using a laser power of 2400 W, a cladding rate of 20 m/min, and a powder feeding rate of 20.32 g/min. The coatings’ cross-sectional morphology corresponded well with the temperature distribution predicted by numerical modeling of the melt pool. The microstructure of the molten coatings is affected by the temperature gradient and cooling rate, which vary greatly from the bottom to the middle to the top. Maximum residual stress appears between the bonding region of the coatings and the substrate, and the coatings themselves have significant residual stress in the form of tensile strains that are mostly distributed in the direction of the laser cladding speed.

The corrugated board packaging industry is increasingly using advanced numerical tools to design and estimate the load capacity of its products. That is why numerical analyzes are becoming a common standard in this branch of manufacturing. Such trend causes either the use of advanced computational models that take into account the full 3D geometry of the flat and wavy layers of corrugated board, or the use of homogenization techniques to simplify the numerical model. The article presents theoretical considerations that extend the numerical homogenization technique already presented in our previous work. The proposed here homogenization procedure also takes into account the creasing and / or perforation of corrugated board, i.e. processes that undoubtedly weaken the stiffness and strength of the corrugated board locally. However, it is not always easy to estimate how exactly these processes affect the bending or torsional stiffness. What is known for sure is that the degradation of stiffness depends, among other things, on the type of cut, its shape, the depth of creasing, as well as their position or direction in relation to the corrugation direction. The method proposed here can be successfully applied to model smeared degradation in a finite element or to define degraded interface stiffnesses on a crease line or a perforation line.

Flood routing in flood forecasting issue, calculation the height of flood bands, determining the river boundaries, and estimation of protective facilities for flood –exposed building is applicable. In many cases, due to the lack of measuring stations, the status of the upstream flood generating hydrograph is not known. The purpose of this study is to present an integrated method comprising of an optimization model and a hydrodynamic numerical model for flood modeling to determine the upstream hydrograph using the provided hydrograph at the downstream measuring station of a river. The routing procedure consists of three steps: (1) generating a hypothetical upstream hydrograph using genetic algorithm method; (2) hydrodynamic modeling using a numerical simulation model for flood routing according to the hypothetical hydrograph which is generated in the first step; (3) compare the calculated and observed hydrograph in downstream by using a fitness function. This recommended procedure was named as Reverse Flood Routing Method (RFRM) and was then applied to Karun River, the largest river in Iran. Comparing the generated upstream hydrograph by the RFRM model with the corresponding measured hydrograph at Ahvaz hydrometric station, as an ungauged river location, shows the high accuracy of the recommended model in this study.

Present study offers mathematical calculations of the roll-coating procedure lubricated with upper Convected Maxwell Fluid. An incompressible isothermal viscoelastic fluid is considered with roll and the porous web having uniform velocities. By employing Lubrication Approximation Theory, the desired equations of motion for the fluid concerned over porous web are modelled and analyzed. The suction rate on the web and injection rate at the roll surface are anticipated proportionate. Results for velocity profile and pressure gradient are obtained analytically. Fluid parameters of industrial significance i.e. detachment point, pressure, sheet /roll separating force, power contribution and coating thickness are also calculated numerically. Substantial and monotonic increase is witnessed in these quantities with the increase of flow parameters.

The United Arab Emirates (UAE) is significantly dependent on desalinated water and groundwater resource, which is expensive and highly energy intensive. Despite the scarce water resource, only 54% of the recycled water was reused in 2015. In this study, an “Oasis” complex comprised of Sustainable Farming Compartments (SFCs) was proposed for reusing treated wastewater to decrease the ambient temperature of the SFC via an evaporative cooling system. A prototype SFC with half the original scale (width = 1.8 m, depth = 1.5 m, front height = 1.2 m back height = 0.9 m) was designed, built, and tested in an environmentally controlled laboratory and field site to evaluate the feasibility and effectiveness of the SFC under the climatic conditions in Abu Dhabi. Based on the experimental results, the temperature drops obtained from the SFC in the laboratory and field site were 5 ̊C at initial relative humidity of 60% and 7- 15 ̊C at initial relative humidity of 50%, respectively. An energy simulation using dynamic numerical simulations was performed in comparison to the results of the experiment. The energy-based dynamic simulation shows good agreement with the experimental results. The total power consumption of the SFC system was approximately three and a half times lower than that of an electrical air conditioner.

Wildland fires are responsible for large socio-economic impacts. Fires affect the environment, damage structures, threaten lives, cause health issues, and involve large suppression costs. These impacts can be mitigated via accurate fire spread forecast to inform the incident management team. We show that a fire forecast system based on a numerical weather prediction (NWP) model coupled with a wildland fire behavior model can provide this forecast. This is illustrated with the Chimney Tops II wildland fire responsible for large socio-economic impacts. The system is run at high horizontal resolution (111 m) over the region affected by the fire to provide a fine representation of the terrain and fuel heterogeneities and explicitly resolve atmospheric turbulence. Our findings suggest that one can use the high spatial resolution winds, fire spread and smoke forecast to minimize the adverse impacts of wildland fires.

Fiber-metal laminates (FMLs) such as Kevlar reinforced aluminum laminate (ARALL), Carbon reinforced aluminum laminate (CARALL), and Glass reinforced aluminum laminate (GLARE) offer great potential for weight reduction applications in automobile and aerospace construction. In order to investigate the feasibility for utilizing such materials in the form of laminates, sheet hydro-bulging tests are studied under the condition of uniform blank holder force for three-layered aluminum and aluminum-composite laminates using orthogonal carbon and Kevlar as well as glass fiber in the middle. The experimental results validate the finite element results and they exhibited that the forming limit of glass fiber in the middle is the highest among the studied materials, while carbon fiber material performs the worst. Furthermore, the crack modes are different for the three kinds of fiber materials investigated in the research. This study provides fundamental guidance for the selection of multi-layer sheet materials in the future manufacturing field.

A three-dimensional, unstructured grid, hydrodynamic and suspended-sediment transport model (i.e., SELFE-SED) was developed to simulate temporal and spatial variations of suspended sediment and was applied to the subtropical subalpine Tsuei-Feng Lake (TFL) of Taiwan. The model was validated with measured water level and suspended‑sediment concentration in 2009, 2010, and 2011. The overall model simulation results are in quantitative agreement with the observational data. The validated model was then applied to explore the most important parameter that affects the suspended-sediment concentration and to investigate the effect of wind stress on the mean current and suspended‑sediment distribution in this shallow lake. Modeling results of sensitivity analysis reveal that the settling velocity is a crucial parameter and erosion rate is less important in the suspended-sediment transport model. Remarkable lake circulation was found based on the strength of wind speed and wind direction. Strong wind would result in higher mean current in the top layer and suspended-sediment distribution in the top and bottom layers. This study demonstrated that the wind stress played a significant influence on mean circulation and suspended-sediment transport in a shallow lake.

In this work the existence and nonexistence of stationary radial solutions to the elliptic partial differential equation arising in the molecular beam epitaxy are studied. Since we are interested in radial solutions we arrive at the following fourth-order differential equation

The World Health Organization estimates that every year air pollution kills seven million people worldwide. As it is expected that climate change will affect future air quality patterns, the full understanding of the links between air pollution and climate change, and how they affect human health, are challenges of future research. In this scope, a methodology to assess the air quality impacts on health was developed. The WRF-CAMx modelling framework was applied for the medium-term future climate (considering the SSP24.5 scenario) and for the recent past (considered as baseline). Following the WHO recommendations, mortality health indicators were used to estimate health impacts of long-term exposures. For that, the Aveiro Region, in Portugal, was considered as a case study. Future climate results indicate the occurrence of higher temperatures, and lower total precipitation. Despite that, improvements in the main pollutants’ concentrations, and consequently in the reduction of the related premature deaths are foreseen, mainly due to the reduction of pollutants emissions imposed by the European legislation for the upcoming years. The applied approach constitutes an added value in this research field, being crucial to anticipate the effects of climate change on air quality and evaluate their impacts on human health.

: This study presents energy and exergy analyses conducted on a Gifford-McMahon cycle refriger-ator. Through detailed numerical simulations, the performance of the refrigerator is thoroughly assessed, with a particular focus on energy and exergy losses. The obtained results are compared with Sankey and Grassman diagrams, providing visual representations of energy and exergy flows within the system. The localization of exergy losses is carefully analysed to identify key areas for optimization aimed at enhancing efficiency and power output. By pinpointing sources of ex-ergy destruction, targeted improvements can be implemented to maximize the overall perfor-mance of the refrigerator. Overall, this research contributes to a deeper understanding of the thermodynamic behaviour of Gifford-McMahon cycle refrigerators and provides valuable insights for optimizing their performance in practical applications.

To identify the exchange coefficients of a nonlinear polynomial tricompartmental general system of α+β , we follow the procedure; firstly, the recommended solution is to introduce an adequate time t*>0 in a determinable manner. That is, after injecting quantity a into the main compartment, wait a moment for the exchange in the polynomial α+β order nonlinear general system to settle, and then compare this compartment to compartment 2 at t*. Secondly, applying the Taylor formula will linearize the system and identify the exchange coefficients. Finally, we will prove that the linearization method is stable.

The investigation of plasma channels induced by focused ultra-short 1030-nm laser pulses in bulk of synthetic HPHT diamond revealed strong dependence of their size and shape on the used numerical aperture of the lens (NA=0.15-0.45). It was shown that at loose focusing conditions, it is possible to significantly increase the length of the plasma channel with a slight increase in pulse power, while tight focusing allows to obtain more compact structures in the same range of used powers. Such dependence paves the way to new possibilities in 3D processing of transparent dielectrics, allowing, for example, to vary the spatial parameters of modified regions without changing the setup, but only by controlling the lens aperture, which seems very promising for industrial applications.

In this paper, possibilities for the bandwidth and wavelength utilization in future next-generation passive optical networks are presented and reasons for realizing and utilizing of extended dynamic wavelength and bandwidth algorithms for NG-PON2 networks are analyzed. Next, principles of the effective dynamic bandwidth allocation are introduced in details, focused on the importance of the decision criterion optimization. For achieving better bandwidth utilization of dedicated wavelengths, this paper is focused on the novel effective dynamic bandwidth allocation algorithm with adaptive allocation of wavelengths to ONU units and on the optimization of the decision criterion. For analyzing the novel extended DWBA algorithm utilizing for various wavelength allocation cases possible in NG-PON2 networks, a simulation program with the enhancement of the EDBA algorithm is realized. Finally, an optimization of the decision criterion defining a minimum bandwidth utilization of the actual wavelength is executed for NG-PON2 networks based on the hybrid TWDM technique.

In this paper, we consider the fourth-order parabolic equations with integer and fractional order time derivatives with Neumann boundary conditions. The integer order time derivatives are approximated by backward Euler difference quotients, and the fractional order time derivatives are approximated by L1 interpolation. We propose the block-centered finite difference scheme for fourth-order parabolic equations of integer and fractional order time derivatives. We prove the stability of the block-centered finite difference scheme and the second-order convergence of the discrete L2 norms of the approximate solution and its derivatives of every order. Numerical examples are given to verify the effectiveness of the block-centered finite difference scheme.

Recently, there has been increasing attention toward inhaled nanoparticles (NPs) to develop in-halation therapies for diseases associated with the pulmonary system and investigate the toxic ef-fects of hazardous environmental particles on human lung health. Taking advantage of microfluidic technology for cell culture applications, lung-on-a-chip devices with great potential in replicating the lung air-blood barrier (ABB) have opened new research insights in preclinical pathology and therapeutic studies associated with aerosol NPs. Surprisingly, the air interface in such devices, which makes them tremendously unique among the other common liquid-based cellular mi-crosystems and enables exposure of cultivated cells to the drug/toxic aerosols, has been largely disregarded. Accordingly, there exists a significant research gap in the comprehensive under-standing of the NPs’ dynamics in the lung-on-a-chip devices, which is momentous to control the injection of aerosols to the target area and attain a desired physiochemical efficacy. To address this research gap, a numerical parametric study is presented to provide a deep insight into the dynamic behavior of the airborne NPs in a gas-liquid dual-channel lung-on-a-chip device with a porous membrane separating the channels. A finite element multi-physics model is developed to enable a particle tracing investigation simultaneously in both air and medium phases to replicate the in vivo conditions avoiding laborious and costly experimental trials. The results include the impact of fluid flow as well as geometrical properties on the distribution, deposition, and translocation of the NPs with diameters ranging from 10 nm to 900 nm in the lung-on-a-chip. The obtained results strongly suggest the aerosol injection of NPs instead of the aqueous solution for more efficient deposition on the substrate of the air channel and higher translocation to the media channel. The current study proposes to optimize the affecting parameters to control the injection and delivery of aerosol par-ticles into the lung-on-chip device depending on the objectives of biomedical investigations and provides optimized values for some specific cases. Therefore, this study can assist scientists and researchers in complementing their experimental investigation in future preclinical studies on pulmonary pathology associated with inhaled hazardous and toxic environmental particles, as well as therapeutic studies for developing inhalation drug delivery.

The process of revitalising quiescent cells in order for them to proliferate plays a pivotal role in the repair of warn out tissues as well as for tissue homeostasis. This process is also crucial in the growth, development and well-being of higher multi-cellular organisms such as mammals. Deregulation of quiescent-proliferation transition is related to many diseases, in particular cancer. Recent studies have revealed that this process is regulated tightly by the Rb−E2F bistable switch mechanism. Based on experimental observations, in this study, we formulate a mathematical model to examine the effect of the growth factor concentration on the proliferation-quiescence transition in human cells. Working with a non-dimensionalised model, we prove positivity, boundedness and uniqueness of solutions. To understand model solution behaviour close to bifurcation points, we carry out bifurcation analysis, which is further verified by use of numerical bifurcation analysis, sensitivity analysis and numerical simulations. Indeed, bifurcation and numerical analysis of the model predicted a transition between stable, bistable and stable states, which are dependent on the growth factor concentration parameter (GF). The derived predictions confirm experimental observations.

Many authors proposed analytical methods for solving fully fuzzy Sylvester matrix equation (FFSME) based on Vec-operator and Kronecker product. However, these methods are restricted to nonnegative fuzzy numbers and cannot be extended to FFSME with near-zero fuzzy numbers. The main intention of this paper is to develop a new numerical method for solving FFSME with near-zero trapezoidal fuzzy numbers that provides a wider scope of trapezoidal fully fuzzy Sylvester matrix equation (TrFFSME) in scientific applications. This numerical method can solve the trapezoidal fully fuzzy Sylvester matrix equation with arbitrary coefficients and find all possible finite arbitrary solutions for the system. In order to obtain all possible fuzzy solutions, the TrFFSME is transferred to a system of non-linear equations based on newly developed arithmetic fuzzy multiplication between trapezoidal fuzzy numbers. The fuzzy solutions to the TrFFSME are obtained by developing a new two-stage algorithm. To illustrate the proposed method numerical example is solved.

We are concerned with the use of some classical spectral collocation methods as well as with the new software system Chebfun in order to compute high order (index) eigenpairs of singular as well as regular Schrodinger eigenproblems. We want to highlight both the qualities as well as the shortcomings of these methods and evaluate them vis-a-vis the usual ones. In order to resolve a boundary singularity we use Chebfun with the simple domain truncation technique. Although this method is equally easy to apply with spectral collocation, things are more nuanced in the case of these methods. A special technique to introduce boundary conditions as well as a coordinate transform which maps an unbounded domain to a nite one are the ingredients. A challenging set of "hard" benchmark problems, for which usual numerical methods (f. d., f. e. m., shooting etc.) fail, are analysed. In order to separate "good"and "bad"eigenvalues we estimate the drift of the set of eigenvalues of interest with respect to the order of approximation and/or scaling of domain parameter. It automatically provides us with a measure of the error within which the eigenvalues are computed and a hint on numerical stability. We pay a particular attention to problems with almost multiple eigenvalues as well as for problems with a mixed (continuous) spectrum. In the latter case we try to numerically highlight its existence. Special attention will be paid to the higher eigenpairs (the pair of eigenvalue and the corresponding eigenfunction approximated by an eigenvector spanning its nodal values).

Based on the geologic conditions of natural gas hydrate (NGH) accumulations in the Shenhu area, northern slope of the South China Sea, this paper used a method of combining reservoir stimulation technique (RST) with depressurization to investigate the conversion efficiency of marine NGH reservoirs in different intrinsic permeability and initial NGH saturation conditions, and analyze the influence of variably-stimulation effect on marine NGH conversion efficiency in different accumulation conditions, provided a reference scheme for improving the NGH conversion efficiency in the Shenhu area. In this work, we performed calculations for the variations in CH4 production rate and cumulative volume of CH4 in different initial NGH saturation, intrinsic permeability and stimulation effect conditions, variance analysis and range analysis methods were used to analyze the significance of these key factors and their interaction, and investigated the sensitivity of stimulation effect on NGH conversion efficiency, respectively. The simulation results showed that stimulation effect have a significant influence on NGH conversion efficiency, and the influence of interaction between these three factors were not obvious. Possibly most important, we clarified an optimum stimulation effect for higher NGH conversion efficiency under different accumulation conditions, especially in low-permeability and high-saturation, which corresponding stimulation effect were different.

Abstract—In the present paper the static and fatigue analysis of plates with holes is conducted. Structures are made of 2D woven roving composites. The parametrization of convex holes is proposed. Experimental results of specimens without holes and with different shapes of notches under static and fatigue tensile loads are presented. The fatigue behaviour of structures is analysed with the use of the low cycle fatigue method. The attention is focused on the nonlinear deformations of 2D woven roving structures leading to the scatter of results. The analysis is supplemented by the numerical finite element modeling. The agreement between experimental and finite element modeling is very good. Since we do not intend to repeat in the abstract the review of the existing literature I would like to emphasize only that the present work is a continuation and extension of the results discussed in the literature – see the next sections of the paper. The finite element modeling of plates with holes is presented in details by Muc [1], Muc, Ulatowska [2] and Muc, Romanowicz [3] including also the problems of the accuracy. The mesh correctness and accuracy is discussed in Ref [2] where the results are compared to the analytical results illustrated in the Soviet Union literature. The experimental results and the form of specimens are shown by Pandita et al. [4] and they are fundaments for our present experimental investigations. Two parametrical description of static and fatigue behaviour of plates with holes characterizes the goal and the novelty of the paper. The analysis demonstrates how those parameters affect on the variations of static and fatigue failure loads. In addition, it should be emphasized that the fuzzy approach is employed herein to reduce the number of experimental data and to avoid statistical analysis of experimental results – see e.g. Muc [5]. In the mesoscale modeling and using the fuzzy approach it is possible to achieve a very good description of static and fatigue behavior of plates with convex holes subjected to tension.

The real-time input of ground motions can effectively assess earthquake disasters in building structures. In this study, we proposed a nearby real-time simulation method that can be applied to assess regional earthquake disasters using structural monitoring recordings based on an urban earthquake simulation system. Real-time accelerations recorded during the 5.1 magnitude Tangshan earthquake were used to update and modify the computing models. El Centro waves were calibrated to 400 cm/s2 for structural seismic resilience analyses. The results indicated that approximately 70% of the structural functions were lost during rare earthquakes. Regional numerical models of 216 buildings were constructed and timeously updated using the Geographic Information System and measured data. The inputting ground motions recorded in the 5.1 magnitude Tangshan earthquake and typical El Centro waves were selected to analyze the structural seismic response, in which the damage indexes were computed, and the damage predictions of regional 216 buildings were also simulated in different levels of earthquakes by being combined with the simplified principles of structural damage estimation. Finally, the evaluation results were visualized in three dimensions using ParaView software. The simulated results of earthquake disasters at an urban scale will promote the prediction abilities of local earthquake administration agencies and have considerable potential to provide essential information for emergency responses and regional disaster mitigation.

The review aims to examine how well numerical indicators of business bankruptcy can predict outcomes. The paper examines ten critical studies that concentrate on statistical models for bankruptcy predictions utilizing PRISMA criteria. The findings highlight the usefulness of numerical indicators in indicating financial hardship, particularly cash flow ratios. In order to connect theoretical knowledge with real-world corporate strategy applications, the study ends by reaffirming the importance of these indicators in strategic decision-making.

This study focuses on the formulation and analysis of a numerical method to compute singularly perturbed functional differential equations (SP-FDEs) involving large mixed shifts. SP-FDEs are a class of differential equations with both shifts and small perturbation parameter. Such equations arise in various scientific fields to model phenomena with memory effects and perturbed dynamics. In this particular study, the considered SP-FDEs involve large negative shift (delay) and large positive shift (advance). Dealing with large mixed shifts in SP-FDEs gives rise to challenges in terms of stability analysis, numerical methods, and convergence of a solution. In this paper, the influence of the large mixed shifts is treated by choosing a uniform mesh discretized in such a way that the term with the shifts lie on the nodal points. Then, using the Numerov’s finite difference method, the continuous problem is transformed into a finite difference scheme and the influence of the perturbation parameter is handled by introducing a fitting factor in the difference scheme. Stability estimate and convergence analysis of the developed scheme are investigated and proved. Numerical experiments are carried out to demonstrate the validity and applicability of the developed scheme. It is shown that the numerical scheme obtained in this work is parameter-robust of second order convergence rate.

Solid asperity interactions are common and inevitable under severe loading conditions for any lubricated contact. Heavy-duty machine components (gear, bearings etc.) generally operate under Mixed Lubrication, where uneven surface features contact each other when generated fluid pressure is not enough to support the external load. The Reynolds equation is commonly used to simulate smooth lubricated contacts numerically. In rough lubricated interfaces where opposite surface asperities make contact, the Reynolds equation alone cannot accurately predict pressure using the traditional numerical simulation method. In this paper, Lubrication-Contact interface conditions (LCICs) have been implemented and extended to solve the multiple asperity contact problem using the full-multigrid approach. The developed novel algorithm has significantly accelerated the solution process and improved the accuracy and efficiency of pressure calculation for fluid-solid sub-interactions that can occur under ML regions. The Finite Difference Method (FDM) results have been compared with Computational Fluid Dynamics (CFD) simulation to validate the newly developed model. Hence, the proposed optimized solution method will provide valuable insight to researchers and industry engineers interested in simulating the ML problem where the effect of the fluid-solid interface can be captured effectively to improve reliability in the calculation of the life expectancy of the lubricated parts.

This study develops a predictor-corrector algorithm for the numerical simulation of IVPs involving singular generalized fractional derivatives with Mittag-Leffler kernels. The proposed algorithm converts the considered IVP into a Volterra-type integral equation and then uses Trapezoidal rule to obtain approximate solutions. Numerical approximate solutions of some singular generalized fractional derivative with Mittag-Leffler kernels models have been presented to demonstrate the efficiency and accuracy of the proposed algorithm. The algorithm describes the influence of the fractional derivative parameters on the dynamics of the studied models. The suggested method is expected to be effectively employed in the field of simulating generalized fractional derivative models

Keywords: underground engineering; numerical simulation; excavation length effect, major principal stress; displacement; damage initiation; CPU time