Pollution by heavy metals is one of the most severe environmental issues that threaten global sustainability. This review presents a recent advance in electrochemical sensors for heavy metal detection Rotating Disk Platinum Electrode are discussed. This study on the production of a modern natural water electrochemical antimony (II) and cupper (II) test include the use of platinum electrode. Antimony and cupper were pre-concentrated on the modified electrode surface and adsorbed to the surface, oxidizing at E = 540 mV and E = 85 mV, respectively. After 20 min of accumulation, time the best-defined anodic peak was obtained of surface. The precision was tested by carrying out chronoamperometric measurements at a concentration of Sb⁺² and Cu⁺² 8.5x10^-8 M and 9.5x10^-7 M, respectively.

MDA, as a sign of oxidative stress, was increasing as a factor that changes the toxicity of responses in the workplace and causes male infertility etiology. This study aims to measure the MDA levels of workers in the casting industry metal. This type of research was analytical explanatory research with a cross-sectional design. This study's variables include the variables taken are MDA levels while the independent variables were age, years of service, type of work, IMT, marital status, and smoking habits. A saturated sampling technique took the research sample of 34 workers. Data analysis used univariate and bivariate methods. The results determined that respondents had MDA hormone levels below the average of 24 or 70.6%, while respondents who had MDA levels above an average of 10 or 29.4%. MDA levels relating to the length of work and marital status, while the type of work, IMT, and smoking habits are not associated with MDA levels in metal casting industry workers in the CV. Bonjor Jaya Klaten.

We report the production of metal oxide (TiFe₂O₄, ZnFe₂O₄) nanoparticles by pulsed laser ablation technique in liquid environment. We used nano second Nd: YAG laser systems working at 532 nm and 1064 nm of wavelength, the energy of the laser beam was kept constant at 80 mJ. Absorbance spectra, surface plasmon resonance, optical band-gap and nanoparticle morphology were investigated using ultraviolet-visible (UV-Vis) spectroscopy, Fourier transform infrared spectroscopy (FTIR), and scanning electron microscopy (SEM). Changing the wavelength of the laser for growth, nanoparticles shown shift between the absorbance and surface plasmon resonance peaks in their UV-Vis spectra, this implies that the optical properties of the colloid nanoparticles depends on laser parameters, this was confirmed with the variation of the band gap energy. Furthermore, red shift for the absorbance peak was observed for samples as-growth at 532 nm around the 150 nm as function of time preparation. Whereas, for the samples as-growth at 1064 nm there is no shift in the absorbance spectra, this can be due to agglomeration and formation of larger particles. The characterization results shown appropriate plasmonic photo-catalysts properties of the particles, hence the photo activation of the nanoparticles was examined on antibacterial effect using colonies of Staphylococcus Aureus and Escherichia coli.

Transition-metal-free synthesis of 4-pyrones via TfOH-promoted nucleophilic addition/cyclization of diynones and water has been developed. This transformation is simple, atom economical and environmentally benign, providing rapid and efficient access to substituted 4-pyrones.

This paper proposes a novel blockchain-based system designed to revolutionize transparency, traceability, and reliability within the organic food supply chain. Addressing persistent challenges such as certification fraud, opaque supply chains, and the high costs associated with organic food production, stakeholders including farmers, processors, distributors, retailers, and consumers stand to benefit from the system’s innovative approach. By leveraging blockchain technology and a robust system architecture, the proposed system offers enhanced transparency, improved traceability, and streamlined certification processes. Through detailed exploration of key components such as user interfaces, smart contracts, consensus mechanisms, IoT integration, and governance frameworks, the paper illustrates the practical application of blockchain technology in improving transparency and traceability throughout the food supply chain. A case study focusing on the organic Tofu supply chain further demonstrates the system’s potential to enhance sustainability, efficiency, and integrity in organic food production and distribution networks. The paper concludes by discussing potential implementation challenges and suggesting areas for future research and development to advance the impact of blockchain technology on the food supply chain.

Mulberries is a type of fruit tree that is rich in nutrients and possesses both medicinal and dietary properties, deeply loved by consumers. The fragrance is a significant factor in the sensory quality of mulberries, playing a crucial role in consumer purchasing behavior. 'Baichang' mulberry is a unique variety of mulberry that emits a strong, creamy-like fragrance, which has enormous potential market value. However, the key metabolites and mechanisms responsible for the formation of this fragrance are still unclear. In this study, we utilized GC-MS technology and RNA-seq to examine the Volatile Organic Compounds (VOCs) and gene expression in 'Baichang' (Morus macroura) mulberries and 'Hongchang' (Morus laevigata) mulberries, the latter of which do not have a distinct fragrance. The results showed that 661 volatile metabolites were detected in both mulberry varieties. Most of these were found in higher relative amounts in the 'Baichang' mulberry variety, with 47 types being present only in the 'Baichang' mulberries, suggesting a rich composition of VOCs in the 'Baichang' mulberry. 312 metabolites were identified as differential metabolites; combining the sensory annotation information and relative content of VOCs, 70 candidate VOCs were annotated as related to the formation of 'sweet, waxy, coconut, and oily' sensations. They could potentially be the key metabolites contributing to the unique aroma of 'Baichang' mulberries. The relative odor activity value (rOAV) analysis revealed that 2(3H)-Furanone, 5-hexyldihydro- was the key VOC contributing to the formation of the special aroma of 'Baichang' mulberries. By RNA-seq, 19 key structural genes related to ester synthesis were identified, including AAT , ACX , ALDH, CYP, EHL, FAD, HPL, and LOX. The high expression of these structural genes in the "Baichang" mulberry fruit is the main reason for its unique creamy aroma. This study provides insights into the aroma differences among different kinds of mulberrie.

The increasing use of chemicals requires a better understanding of their presence and their dynamics in the environment as well as their impact on ecosystems; it is therefore important to set up procedures. The aim of this study was to validate the first steps of an innovative multi-omics approach based on metabolomics and 16S metabarcoding data for future analyses of the contaminants fate and impact in Mediterranean lagoons. First, semi targeted analytical procedures for water and sediment matrices were set up to evaluate the lagoon contamination status. Forty-six compounds were detected, 28 could be quantified in both water (between 0.09 and 47.4 ng/L) and sediment (between 0.008 and 26.3 ng/g) samples using UHPLC-MS/MS instrument. Regarding the non-targeted metabolomics study (UHPLC-HRMS), four sample preparation protocols, based on solid/liquid extractions and an automated pressurized fluid extraction system (EDGE® extractions), were compared in terms of metabolome coverage, efficiency and reproducibility of the extraction methodology. A solid/liquid extraction using acetonitrile/methanol (50/50) solvent was the best protocol. On the other hand, in order to characterize the microbial diversity of the lagoon sediment using metabarcoding, five commercial kits for DNA extraction were evaluated. This study revealed that the DNeasy PowerSoil Pro Qiagen Kit (Promega, USA) was the best compromise for studies assessing microbial diversity in fresh sediment.

The principal aim of this descriptive-survey investigation is to ascertain the factors influencing individuals' choice to purchase organic commodities in Tehran. The statistical populace for this examination comprised all patrons of food retail establishments in Tehran, with the sample size determined using the Cochran formula for an unknown community size, involving the distribution of 30 questionnaires to customers (n=439). Data collection was carried out through a random sampling technique. The survey instrument consisted of a questionnaire with two sections consisting of general queries (7 questions) and specific inquiries (23 items) categorized into four dimensions (product, price, place, and promotion) for the clientele. The questionnaire's validity was confirmed through face and content validation, while its reliability was assessed utilizing Cronbach’s alpha. Data analysis was conducted using SPSS25 software, encompassing both descriptive and inferential statistical analyses. The results revealed a positive and significant correlation between customers' inclination to consume organic goods and the characteristics of the product, price, and promotion. However, no association was found between the propensity to consume organic products and location characteristics. Concerning contextual variables, a solely positive and significant correlation was identified between the willingness to purchase organic items and consumer income levels. No significant relationships were detected between other contextual variables and organic product consumption. A notable contrast was observed between respondents' gender and their readiness to buy organic products, while no significant variances were noted regarding age, income, occupation, and education in relation to the propensity to purchase organic commodities.

This article explores the geothermal resources of Kazakhstan's Zharkent Basin, with a specific focus on the high-temperature geothermal sources in the Almaty region of Southern Kazakhstan. The research aims to analyze the energy characteristics of the Organic Rankine Cycle (ORC) for harnessing low-enthalpy geothermal energy for small-scale electricity generation. A detailed thermodynamic model was developed, employing R134a as the working fluid. An in-depth analysis of the Zharkunak field (Zharkent, Almaty region) revealed that well 5539, with its notably high temperatures, offers the highest potential for geothermal electricity production, achieving an annual output of approximately 10,371 MWh. The total electric power output from the studied wells in the region is estimated at 20,111 MWh annually, representing a significant contribution towards sustainable energy production and reducing reliance on traditional coal-fired power plants. The study concludes that the Organic Rankine Cycle is not only a viable and efficient technology for utilizing low-enthalpy geothermal resources to generate electricity on a small scale, but also a key player in enhancing energy independence. By leveraging local geothermal energy, the Almaty region can significantly reduce its reliance on external energy sources, thereby fostering sustainable development and reducing environmental impacts.

Anaerobic digestion of waste material to biogas, with the remaining digestate slurry used as agricultural biofertilizer, is already a route of sustainable fuel production and its uptake will grow further. However, the foam layer that forms on top of the reacting mixture impedes the process and leads to liquid and solid material contaminating the gas product. Ideally, any effective foam repression should be low-cost, and react fast. Therefore, methods of optimizing anaerobic digestion need foam repression as one of the parameters in increasing gas yield. Foam can be repressed by pre-treating substrate which destroys filamentous bacteria and adding trace elements. The drawback to this method is the high cost of pre-treatment, the trace elements not being biodegradable and being toxic at high concentration; this method does not completely repress foam and is only effective under moderate organic loading

Polycyclic aromatic hydrocarbons (PAHs) and polychlorinated biphenyls (PCBs) exist in the atmosphere in the vapor and particulate phases, as well as in the solubilized form in fog/rain/cloud waters. They are abundant pollutants and are known for their acute and chronic toxicity. In the current paper, fogwater samples are collected during 42 events between 2015 and 2021 at four sites (Strasbourg, Geispolsheim, Erstein, Cronenbourg) in the Alsace region with different topological characteristics. PAHs and PCBs are extracted using the liquid-liquid extraction (LLE) supported on a solid cartridge (XTR Chromabond), and then analyzed by gas-chromatography tandem mass spectrometry (GC-MS/MS). Total PAHs and PCBs concentration in fog samples varied between 0.58 and 6.7 µg L-1 (average of 2.70 µg L-1), and 0.14 and 15.5 µg L-1 (average of 2.75 µg L-1). Low molecular weight (LMW) predominant and highly detectable over high molecular weight PAHs by at least 1.6 times, while pentachloro-biphenyls are the dominant PCB congener accounting for at least 50% of the total fraction. PAHs and PCBs concentrations have increased over sampling years at all sites, except a slight decrease in PCBs level at Geispolsheim. Diagnostic ratio analysis suggested that diesel and fossil fuel combustion are the dominant contributors to PAHs in Alsace

Cacao (Theobroma cacao L.) is an important woody species for production in Ecuador. Woody species have the potential to incorporate soil organic carbon (SOC) into the soil. The province of Manabí is known for its cocoa plantations and several cocoa species, which generates interest in their analysis. This study aimed to determine the concentration and accumulation of SOC in three cocoa species (EET95, EET103 and EET116) 15 years old, both under the tree and in the rows, at different depths 0-5, 5-10, 10-20 and 20-30 (cm). The results showed that soil SOC concentration was higher in the row for EET116 (2.51%) and significantly different under the tree for EET103 (1.57%) at 0-5 cm. No significant differences were found in the other sections. In the whole profile analyzed (0-30 cm), the EET116 species accumulated 41 t ha-1 and 54 t ha-1 under the tree and in the row, respectively. The species EET103 in the row presented 47 t ha-1 with no significant differences. Species EET95 and EET103 had the lowest values, but without significant differences between sampling locations, with 36 t ha-1, 37 t ha-1, and 47 t ha-1 under the tree and in the windrow, respectively. In conclusion, the species EET116 accumulated more organic carbon due to several factors, possibly a higher decomposing biomass, not only from the tree but also from other trees in the area, which contributes to the incorporation of organic matter throughout the soil profile.

This paper evaluates the global sustainable competitiveness of three blocks of power (US, China and EU) based on OGT (Organic Growth Theory) structure. In addition, a sensitivity analysis of COVID-19 on three measures of global sustainable competitiveness, economy, environment and social is also presented. OGT is a well-thought-through and standard framework for evaluation of any type of organiza-tion in their pathway to experience truly sustainable growth. GDP (Gross Domestic Product) is used as an economic measure; total carbon emissions equivalent is used as an environmental measure and HMI (Human Development Index) as a social measure. It is concluded that the pandemic has paused the evolution of countries to be truly world centric countries. However, the recovery plans seem to be highly aligned with the OGT scores and it is expected that the scores to improve dramatically.

The influence of the ligands in coupled organic-inorganic nanostructures (COINs) on the performance of optoelectronic devices is investigated. We fabricated photodiodes based on pentacene and PbS nanocrystals coupled to organic ligands like 1,2-ethanedithiol (EDT) and tetrabutylammonium iodide (TBAI) and a combination of both, EDT and TBAI, as a heterostructure. These ligands were first separately used to fabricate single ligand-type of organic-inorganic devices and later compared with a heterostructure of PbS-EDT and PbS-TBAI. To tune the optical energy gap of COINs to align with the triplet level of pentacene, it was necessary to choose a suitable particle size. For this purpose, ultraviolet photo-emission spectroscopy (UPS) was used to determine the energy of the highest occupied molecular orbital (HOMO) and the work function of COINs, while the energy of the lowest unoccupied molecular orbital (LUMO) of COINs was estimated subsequently by adding the exciton binding energy and the optical band gap to the measured HOMO energy. Devices with heterostructure COINs achieve a higher short circuit current than COINs with a single type of the ligands. Finally, even if the requirements of proper energy level alignment are satisfied, the photodiodes' performance was affected by the morphology of COINs. This finding has been demonstrated by atomic force microscopy (AFM) and transmission electron microscopy (TEM). Incident photon to current efficiency (IPCE) shows a shift for the excitonic absorption peaks in the visible range at opposite applied voltages. The IPCE signal for the double heterostructure device is higher than the single type device.

Organic electrochemical transistors (OECTs) based on conducting polymers have attracted significant attention in the field of biosensors. PEDOT:PSS and polyaniline (PANI) are representative conducting polymers used for OECTs. While there are many studies on PEDOT:PSS, there are not so many reports on PANI-based OECTs, and a detailed study to compare these two polymers has been desired. In this study, we investigated the fabrication conditions to produce the best performance in the OECTs using the above-mentioned two types of conducting polymers. Two main parameters were film thickness and film surface roughness. For PEDOT:PSS, the optimal conditions for fabricating thin films were a spin-coating rate of 3000 rpm and DI water immersion time of 18 hours. For PANI, the optimal conditions were a spin-coating rate of 3000 rpm and DI water immersion time of 5 seconds, and adding dodecylbenzenesulfonic acid (DBSA) was found to provide better OECT performances. The OECT performances based on PEDOT:PSS were superior to those based on PANI in terms of conductivity and transconductance, but PANI showed excellence in terms of film thickness and surface smoothness, leading to the good reproducibility of OECT performances.

Results of profile loss measurements, including trailing edge flow details, are presented for the flow of an organic vapor through a linear turbine cascade. The so-called VKI-I blade profile from the open literature was chosen for the cascade, and the working fluid was NOVEC 649. Pitot probes and hot wire anemometry were employed to measure the flow field up and downstream of the cascade. Details of the unsteady flow caused by the trailing edge of the blades and the turbulent spectrum were investigated using hot-wire anemometry. The new organic vapor flow results were compared with literature data obtained for air and with the prediction of conventional literature loss models. It was found that under certain thermodynamic conditions, specific traditional loss models can reasonably predict organic Rankine cycle (ORC) turbines' profile loss. Still, significant deviations between the loss models and the experimental data can also occur.

Compared with the traditional bundle pricing strategy with fixed products, this paper proposes a more flexible interactive bundle pricing strategy (IBPS) for agricultural e-retailers. Since more and more consumers tend to buy more environmentally friendly and healthy organic agricultural products, we consider consumers' organic preferences and build a mixed bundle pricing model for organic and inorganic agricultural products. A free shipping strategy is introduced to maximize retailer profit and optimize consumer surplus. Through numerical analysis, we find: (1) Compared with the traditional online retailing method, IBPS can effectively stimulate consumption and higher retailer profit; (2) As the free shipping threshold increases, the total profit shows a trend of first increasing and then decreasing, indicating that a suitable free shipping threshold can optimize the retailer profit; (3) As the consumer green preference increases, the total sales of agricultural products decrease, but the organic sales improve, while total profit rises; (4) The higher the level of consumption, the higher the sales volume of organic products and there is an upward trend in the profits of e-retailers.

Agriculture is the mainstay of the Ethiopian and a key sector of its economy. However, Lack of productive and environmentally friendly technology is not widely applicable elsewhere. Likewise, the vermicomposting technology is a recently emerging science which not effectively transferred to the users across the country. Thus, this review is aimed to shine the importance, unexploited opportunities and the challenges hindered for further expansions in Ethiopian context. Vermicompost is among the powerful organic fertilizers which enhance soil Fertility and productivity. As agrarian society; there are plenty of raw byproducts and weed species which are not center of focus (i.e cattle waste, crop residues and invasive weeds like P.Juliflora, P.hysterophorus and E.crassipes respectively). However, there are many constraints there like policy issue, handling problems and sensitivity of the worms for different environmental factors which hindered to invest on a wide range. Generally, the number and weight of vermiculture as well as amount of produced casts are promised and every possible ways were recommended to entertain on the large scale.

A The present investigation was undertaken in foothill regions of Uttarakhand from July-2016 up to December-2018. A total of thirty four different sites ranging from the roadside areas, grasslands to forests were studied and Mushroom fruiting bodies were collected. A total of One Hundred sixty six fruiting counts were obtained and 68 mushroom genera belonging to 15 orders and 43 families were identified. During collection visits mushroom were apparent from organic debris of diversified habitats ranging from humid soil; grassland; leaf litter; living tree trunk; dead wood log of forest zone. Maximum fruiting bodies (75%) were obtained between July to September and minimum i.e. 6% between November – February. Among the collected mushroom Stereum rugosum, Crepidotus variabilis, Laccaria laccata, Schizophyllum commune, Ganoderma applantum, Cantharellus cibarius were more prevalent. Out of all collected mushroom sample the frequency of Mushroom belonging to order Agaricales was 45.18% followed by Polyporales i.e., 27.7%. The collected mushroom were cultured on PDA medium and their mycelial forms were preserved for further studies.

Air pollution is a serious global issue, responsible for approximately one in every nine deaths each year, ranking it among the greatest environmental hazards to human health. It is of particular concern in urban areas, where elevated pollutant concentrations and potential sufferers converge. Over one half of the world’s population presently lives in urban areas, and the urban population ratio is expected to reach 68% by 2050. Common air pollutants include particulate matter (PM), sulphur dioxide (SO2), ground-level ozone (O3), nitrogen oxide (NOx) and carbon monoxide (CO). While elevated rates of air pollution pose serious health risks for humans, outdoor plants can help reduce the harmful effects of air pollution by filtering and purifying the air around us.In this project Common Ivy, Aster and Miniature Andromeda plants were evaluated for air pollutant mitigation. In this study we developed a vegetation barrier model with the plant located in the middle of the greenhouse box, and air pollutant was sprayed on one side of the plant. Dispersion patterns of sprayed pollutants were tested with and without vegetation barrier. Measurements of carbon dioxide (CO2), Formaldehyde (HCHO), Total Volatile Organic Compounds (TVOC), and Particulate Matter (PM2.5/PM10) were taken before spraying, then at 0 and 30 minutes after spraying, using both monitors.The results show mitigation rates (in 177 ft3 of air after 30 min): for TVOC the minimum reduction is 5 mg/m3; for HCHO, 1 mg/m3; for CO2, 2000 ppm; for PM2.5, 2000 ug/m3; and for PM10 it was 1000 ug/m3.

In the last 10 years, carbon dots (CDs) synthesized from renewable organic resources have been gathered a considerable amount of attention in different fields for their peculiar photoluminescent properties. Moreover, the synthesis of CDs fully responds to the principles of the circular chemistry and the concept of safe-by-design. This review will focus on the different strategies for the incorporation of CDs in organic light-emitting devices (OLEDs) and on the study of the impact of CDs properties on the OLEDs performance. The main current research outcomes and highlights are summarized to guide users towards the fully exploitation of use these materials in optoelectronic applications.

A prime site of astrobiological interest within the Solar System is the interior ocean of Enceladus. This ocean has already been shown to contain organic molecules, and is thought to have the conditions necessary for more complex organic biomolecules to emerge and potentially even life itself. This sub-surface ocean has been accessed by Cassini, an unmanned spacecraft that interacted with the water plumes ejected naturally from Enceladus. The encounter speed with these plumes and their contents, was between 5 and 15 km s⁻¹. Encounters at such speeds allow analysis of vapourised material from submicron-sized particles within the plume, but sampling micron-sized particles remains an open question. The latter particles can impact metal targets exposed on the exterior of future spacecraft, producing impact craters lined with impactor residue, which can then be analysed. Although there is considerable literature on how mineral grains behave in such high-speed impacts, and also on the relationship between the crater residue and the original grain composition, far less is known regarding the behaviour of organic particles. Here we consider a deceptively simple yet fundamental scientific question: for impacts at speeds of around 5–6 kms⁻¹ would the impactor residue alone be sufficient to enable us to recognise the signature conferred by organic particles? Furthermore, would it be possible to identify the organic molecules involved, or at least distinguish between aromatic and aliphatic chemical structures? For polystyrene (aromatic-rich) and poly(methyl methacrylate) (solely aliphatic) latex particles impinging at around 5 km s⁻¹ onto metal targets, we find that sufficient residue is retained at the impact site to permit identification of a carbon-rich projectile, but not of the particular molecules involved, nor is it currently possible to discriminate between aromatic-rich and solely aliphatic particles. This suggests that an alternative analytical method to simple impacts on metal targets is required to enable successful collection of organic samples in a fly-by Enceladus mission, or, alternatively, a lower encounter speed is required.

Intensive greenhouse horticulture can cause various environmental problems. Among them, the management, storage and processing of crop residues can provoke aquifer contamination, pest proliferation, bad odors or the abuse of phytosanitary treatments. Biosolarization put in value any fresh plant residue and is an efficient technique for the control of soil-borne diseases. This study aims to examine an alternative means of managing greenhouse crop residues through biosolarization and to investigate the influence of organic matter on yield and quality of tomato (Solanum lycopersicum, L.) fruit. With this purpose, the following nutritional systems were evaluated: inorganic fertilization with and without brassica pellets (Fert, Fert + and Fert ++), fresh tomato plant debris with and without brassica pellets (Rest, Rest + and Rest ++) and no fertilizer application (Control). The addition of organic matter equaled all the treatments except for control with regard to yield and quality of the tomato fruit. In light of these results, the application of tomato plant debris to the soil through biosolarization is postulated as an alternative for the management of crop residues, solving an environmental problem and having a favorable impact on the production and quality of tomatoes as a commercial crop.

Recently, coastal swamps have been acknowledged for their capability to alleviate shorelines and defend coastal communities. Mangroves play a prominent role in obstructing water currents in riverbanks, shorelines, and coastal areas. Mangrove roots have the significant contribution to the resiliency of the vegetation structure. Yet, mangrove model has lately been called into question by lab experimental evidence. In this paper, the flow characteristics past root models are reviewed. coastal swamps are among the most fruitful and carbon‐rich ecosystems on the planet. Long‐term carbon putting away in coastal wetlands happens mostly below ground as soil organic matter. Mangrove servs as a carbon sink, impacts wetland ecosystem configuration, purpose, and firmness. To expect and ease the properties of climate change, there is a necessity to advance considerate of environmental controls on wetland. The impact of four soil formation factors are reviewed. Across the shorelines, soil organic matter was highest in mangrove forests and it was lower areas.

We demonstrated an ITO-free, highly transparent organic solar cell with the potential to be integrated into window panes for energy harvesting purposes. A transparent, conductive ZnO/Ag/ZnO multilayer electrode and a Ag:Ca thin film electrode were used in this transparent device as the bottom and top electrode, respectively. To further improve the transmittance of the solar cell, the thickness of the top ZnO layer was investigated by both experiment and simulation. An average visible transmittance of > 60% was reached, with a maximum transmittance of 73% at 556 nm. Both top and bottom illumination of the solar cell generated comparable power conversion efficiencies, which indicates the wide application of this solar cell structure. In addition, we fabricated distributed Bragg reflector mirrors with sputtered SiO2 and TiO2, which efficiently increased the power conversion efficiency over 20% for the solar cells on glass and PET substrates,

Byers Peninsula is considered one of the largest ice-free areas in Maritime Antarctica. Since 2006, the Spanish Polar Program has taken part in a large number of environmental studies involving effects of climate changes in lives cycles, limnology and microbiology. Soils from maritime Antarctica are generally weakly developed and have chemical, physical and morphological characteristics strongly influenced by the parent material. However, biological activity during the short Antarctic summer promotes intense transference of nutrients and organic matter in areas occupied by different species of birds and marine mammals. To mapping and monitoring those areas with high biological occupation, could be very useful to have models of edaphic properties prepared from satellite images. In this approach, Deep Learning and Linear Regression models of soil properties and spectral indexes as explicative variables were performed. We training models of soil properties closely related to biological activity such as Dissolved Organic Carbon (DOC) and the iron fraction associated with organic matter (Fe). We tested the best approach to model the spatial distribution of DOC, Fe and pH by training models of Linear Regression and Deep Learning over Sentinel2 and WorldView2 images. The most robust models were used to track possible areas with ornithogenic soils as well as areas of the Byers Peninsula that could support the highest biological development.

A series of D–π–A diketopyrrolopyrrole (DPP)-based small molecules have been designed for organic light-emitting diodes (OLEDs) and organic solar cells (OSCs) applications. Appling the PBE0/6-31G(d,p) method, the ground state geometry and relevant electronic properties were investigated. The first excited singlet state geometry and the absorption and fluorescent spectra were simulated at the TD-PBE0/6-31G(d,p) level. The calculated results reveal that the photophysical properties are affected through the introduction of different end groups. Furthermore, the electronic transitions corresponding to absorption and emission exhibit intramolecular charge transfer feature. It was disclosed that the designed molecules act not only as luminescent for OLEDs, but also donor materials in OSCs. Moreover, they also can be used as potential electron transfer materials using for OLEDs and OSCs.

The SPEcies-At-Risk index for metals (SPEARmetal) was refined using updated physiological sensitivity data and validated to assess the ecological impact of metal contamination on benthic macroinvertebrate communities in the upper Nakdong River, near a Zn smelter in Korea. Biosurvey and chemical monitoring were collected at 18 sites surrounding the smelter and nearby mines. Acute ecotoxicity tests on 20 indigenous species from the Korean peninsula were conducted and used to update taxon-specific metal sensitivity data. The refined SPEARmetal index, based on this updated sensitivity, was significantly lower than previous versions, with most values below the severe impact threshold (0.5) in the mainstream. The correlation between hazard quotients in water and the SPEAR index improved, with the correlation coefficient increasing from 0.63 to 0.70. Despite consistently high benthic macroinvertebrate indices (BMI) across the study area, generic ecological indices such as total richness, EPT (Ephemeroptera, Plecoptera, Trichoptera), and Shannon diversity showed correlations with metal contamination levels. Principal component analysis identified SPEARmetal as the primary indicator associated with metal contamination in both water and sediment. These findings highlight the improved performance of the refined SPEARmetal index as a more sensitive and specific tool for assessing the ecological status of metal-impacted aquatic ecosystems compared to traditional indices.

Quantifying methane emissions is essential for meeting near-term climate goals and typically done using methane concentrations measured downwind of the source. One major source of methane that is important to observe and promptly remediate is fugitive emissions from oil and gas productions sites but installing methane sensors at the thousands of sites within a production basin is expensive. In recent years, relatively inexpensive metal oxide sensors have been used to measure methane concentrations at production sites. Current methods used to calibrate metal oxide sensors have been shown to have significant shortcomings resulting in limited confidence in methane concentrations generated by these sensors. To address this, we investigate using machine learning (ML) to generate a model that converts metal oxide sensor output to methane mixing ratios. To generate test data, two metal oxide sensors, TGS2600 and TGS2611, were collocated with a trace methane analyzer downwind of controlled methane releases. Over the duration of the measurements, the trace gas analyzer’s average methane mixing ratio was 2.40 ppm with a maximum of 147.6 ppm. The average calculated methane mixing ratios for the TGS2600 and TGS2611 using the ML algorithm were 2.42 ppm and 2.40 ppm with maximum values of 105.9 ppm and 106.3 ppm, respectively. A comparison of histograms generated using the analyzer and metal oxide sensors mixing ratios show overlap coefficients of 0.95 and 0.94 for the TGS2600 and TGS2611, respectively. Overall, our results showed there was a good agreement between the ML derived metal oxide sensors’ mixing ratios and those generated using the more accurate trace gas analyzer. This suggests that the response of lower-cost sensors calibrated using ML could be used to generate mixing ratios with precision and accuracy comparable to higher price trace methane analyzers. This would improve confidence in low-cost sensors’ response, reduce the cost of sensor deploying, and allow for timely and accurate tracking of methane emissions.

Wild-grown edible mushrooms are important in world diet, which are also efficient metal accumulators. Yunnan, southwest China is the main producing region with typically high geochemical metals. Environmental factors, bioaccumulation, distribution and human health risk of metals were examined in paired soil and Tricholoma matsutake (n=54). T. matsutake grows on acidified soils (pH=3.95–6.56) and metals showed strong heterogeneity with Fe, Mn, Zn and Cu ranged at 16–201, 0.046–8.58 g kg–1 and 22.6–215, 3.7–155 mg kg–1. High soil Fe content led to its great accumulation in T. matsutake (0.24–18.8 g kg–1). However, though soil Mn content was great higher than Zn and Cu, their concentrations in T. matsutake were comparable (21.1–487 vs. 38.7–329 and 24.9–217 mg kg–1). This suggested that T. matsutake prefers to accumulate Zn and Cu than Mn, and supported by bioaccumulation factor (BAF=0.32–17.1 vs. 0.006–1.69). Fe was mainly stored in stipe, while Mn, Zn and Cu were in cap, with translocation factor (TF) was 0.58 vs. 1.28–1.94. Therefore, stipe Fe showed the highest health risk index (HRI) at 1.28–26.9, followed by cap Cu (1.01–2.33), while 98–100% of Mn and Zn were risk-free. The higher concentration and greater risk of Fe was attributed to the significant effect of soil Fe content (R=0.34) and soil pH (R=–0.57). This study suggested that Fe as an essential mineral may exert toxic effects via T. matsutake consumption from geochemical high background areas.

Honey is a very cost-efficient food source and a valuable export for the country of Uganda, but is commonly adulterated, resulting in consumers not being aware of the contents of their honey. As a result, it is important to be able to authenticate the honey that consumers are purchasing. This study evaluated the physicochemical properties (pH, free acidity, metal determination, moisture content, and FTIR spectra) of Ugandan and Manuka honey. Honey pH values ranged from 3.3 to 4.8 (±0.6) while free acidity values ranged from 34.87 to 62.22 (±8.69). The moisture content values of all honey samples were below 22%. The metal concentrations and functional groups present in Ugandan and Manuka honey were determined. Metal analysis by atomic absorption spectrometry detected five elements (Na, Ca, K, Cu, and Pb) in all honey samples in varying concentrations. The elemental concentrations were found in descending order as follows: sodium (Na) (9.38 ppm), calcium (Ca) (4.99 ppm), potassium (K) (2.48 ppm), copper (Cu) (1.87 ppm), lead (Pb) (0.28 ppm). FTIR analysis revealed similar patterns of spectral curve (O-H stretching and C-H stretching) across all honey samples analyzed, which is consistent with previously analyzed honey samples from other studies. Ugandan honey sample 7 collected in the Masaka Region was found to be most similar to the Manuka honey standard based on its observed physiochemical properties. All properties analyzed suggested Ugandan honey is of good quality and safe for consumption.

The characteristics of gap plasmon formed by nanoparticle-on-mirror (NPOM) structure composed of metal nanoparticles (MNP) and metal thin films have aroused the interest of various optoelectronic devices. The resonant spectrum obtained by the internal coupling effect of gap can be flexibly controlled by the polarization of incident light and the thickness of the dielectric layer between MNP and metal thin films. We have theoretically studied the resonance spectra of polarization-dependent gold ellipsoidal nanoparticles (GENP) and gold thin films in the gap region of NPOM structures. GENP and gold thin films are separated by a dielectric layer with a refractive index of 1.36. We observe that the intensity of the local electric field resonance peak in the gap region is inversely proportional to the polarization angle. Similarly, the intensity of the local electric field resonance peak in the gap region is inversely proportional to the thickness of the dielectric layer. We have obtained more than 2200 V/m local electric field intensity (dielectric layer thickness 0.3nm). Finally, the resonant peak wavelength of the electric field in the gap region of the NPOM structure is also controlled by the polarization angle of the incident light and the thickness of the dielectric layer.

Additive manufacturing processes offer various options to fabricate metal parts, which show numerous ecological and technological advantages compared to formative and subtractive manufacturing methods. Due to quick availability and high accuracy, they are particularly suitable to produce complex prototypes. Metal fused deposition modeling is a relatively new material extrusion additive manufacturing technique based on the widely used fused filament deposition process. This study focuses on the Inconel 625 metal filament from Markforged Inc., it consists of a mixture of metal powder and a binder system, the latter being removed during washing and sintering. In this article, the mechanical properties of printed and sintered Inconel were investigated using tensile testing specimens with three different infill patterns, solid, triangular, and gyroid, printed in flatwise and upright direction. In addition, investigations into the dimensional accuracy of the printed specimens and the sintering shrinkage were carried out. The results showed that neither the dimensional accuracy nor the sintering shrinkage was significantly influenced by the printing orientation. In the context of lightweight engineering, the structures proofed beneficial especially within the elastic region. Generally, triangular infill patterns resulted in higher stiffness, while gyroids led to more ductile specimens. A mass-related evaluation of tensile testing elucidates that with aid of the infill structures weight savings of 40 % resulted in mechanical performance decreased by only 20 % on average.

This research focusing on the environmental impact of tire and brake pad wear constitutes a significant area of transport-related studies. These two key vehicle components are not only the most frequently worn, but also generate micro and nano pollutants (i.e., rubber, metal oxides) that potentially harm the environment. Over half of the globally produced natural and synthetic rubbers, which amounted to about 30 million tons in 2022, are used for tire production. According to Wagner et al.'s research, over 1.3 million tons of such particles are released due to wear and tear in the European Union alone. This work focuses on examining snow deposits from various locations in an urban agglomeration (Poznan, Poland) in the winter season. FT-IR and NMR spectroscopic studies, optical and electron scanning microscopy SEM-EDS, and particle size studies using the DLS technique were conducted for a detailed characterization of pollutants in the environment. The conducted particle separation methods allowed for the extraction of a fraction mainly containing gum residues with particle sizes less than 2 µm. The results of these studies are crucial for understanding the impact of vehicle part exploitation on the environment.

Multilayered metallic sheets fabricated by hot metal forming processes are attractive structural components in the aerospace and automobile industry. The strength of the mechanical bond between the different layers is critical to the applicability of such components in load bearing applications. While it is well understood that the process conditions such as temperature, deformation and rate of deformation influence the bond strength, a clear functional relationship between these conditions and the bond strength has yet to be established. The objective of the current study is to investigate the joining of Aluminum-6061 alloy specimens by hot compression bonding. Hot compression tests of beam specimen pairs were conducted at different temperatures (300-500℃), with different strains and strain rates (10-2-10-1 [1sec]). Coupled thermo-mechanical finite element models were utilized to compute the time dependent thermo-mechanical fields that develop along the specimen interface. The computed values were used to map the spatial distribution of a scalar parameter J which is hypothesized to govern bond formation. Mechanical tensile tests were used to determine the bond strength and expose the bonded surfaces. It is demonstrated that the computed J distribution can be correlated well with SEM observations of the debonded surface. It is also shown that the actual bonded area can be predicted from the computations for a certain range of critical J values.

Laser powder bed fusion can fabricate porous structure through lattices, but it remains a challenge to prepare micropores (

Serine peptidase CLPP is conserved among bacteria, chloroplasts, and mitochondria. In humans and mice, its loss causes Perrault syndrome with growth deficit, infertility, deafness, and ataxia. In the filamentous fungus Podospora anserina, CLPP-loss leads to longevity. CLPP substrates are selected by CLPX, an AAA+ unfoldase. CLPX is known to target delta-amino-levulinic-acid synthase (ALAS) to promote pyridoxal-phosphate (PLP) binding. CLPX may influence cofactor association with other enzymes. Here, the evaluation of P. anserina metabolomics highlighted arginine/histidine reduction. In Mus musculus cerebellum, reductions of Arginine/Histidine and Citrulline occurred with concomitant accumulation of heme-precursor protoporphyrin-IX. This suggests that increased biosynthesis of 5-carbon (C5) chain deltaALA consumes not only C4 succinyl-CoA with C1 glycine but also specific C5 delta amino-acids. As responsible enzymes for these converse effects, elevated abundance of CLPX and ALAS is paralleled by elevation of OAT (PLP-dependent, ornithine-delta-aminotransferase). Possibly as consequence of altered C1 metabolism, CLPP-null cells in P. anserina proteome profiles showed strong accumulation of a methyltransferase and two mitoribosomal large subunit factors. Reduced Histidine levels may explain previously observed metal interaction problems. As main nitrogen-storing metabolite, deficient Arginine would affect the urea cycle and polyamine synthesis. Supplementation of Arginine and Histidine might rescue growth deficits of CLPP-mutant patients.

This study investigates novel ferrocene-based electrochemical sensors for metal cation detection through the design, synthesis and characterisation of ferrocene derivatives. Specifically, the re-search determines the redox potentials of ferrocene versus decamethylferrocene to provide in-sight into the redox potential variations between them. The investigation also examines how electrochemical oxidation of the ferrocene moiety can modulate host affinity for transition metals cations via effects such as electrostatic interactions and changes to coordination chemistry. Metal ion coordination to receptors containing functional groups like imine and quinoline is explored to elucidate selectivity mechanisms. These findings advance the fundamental understanding of ferrocene electrochemistry and host-guest interactions, supporting the development of improved cation sensors with optimised recognition properties, sensitivity, and selectivity. Overall, the work lays the necessary groundwork for applications in analytical chemistry and sensor technologies through customised ferrocene-derived materials.

Laser heat treatment is applied after coating. Evaluation of the results was performed by studying the microstructures by metallographic, SEM/EDX microscopy and the mechanical properties were obtained by microscopic hardness and abrasion resistance. The objective of this study was to investigate the effect of laser heat treatment on the wear resistance of metal coatings. The results show the influence of the microstructure and chemical composition of the electrodes used on the micro-hardness and wear resistance of the metal coatings.

The cohesive energy of transition metal nanoparticles is crucial to understanding their stability and fundamental properties, which are essential for developing new technologies and applications in fields such as catalysis, electronics, energy storage, and biomedical engineering. In this study, we systematically investigate the size-dependent cohesive energies of all the 3d, 4d, and 5d transition-metal nanoparticles using first-principles density functional theory calculations. Our results show that the cohesive energies of nanoparticles decrease with decreasing size due to the increased surface-to-volume ratio and quantum confinement effects. We also find that the size-dependent cohesive energy trends are different for different transition metals, with some metals exhibiting stronger size effects than others. Our findings provide insights into the fundamental properties of transition-metal nanoparticles and have potential implications for their applications in various fields such as catalysis, electronics, and biomedical engineering.

Copper smelting has been the source of soil contamination in trace metals in Penga Penga (Lubumbashi). Residents are exposed to trace metal ingestion and planting trees is challenging in such soil conditions. Nevertheless, planting trees in former household dumps or using various types of amendments allowed the provisioning of fruits in few residences. In the perspective of scaling up the process, a survey has been conducted with the aim of assessing the effectiveness of the planting processes on the trace metal content in fruits and leaves of Mangifera indica L. and Syzygium guineense (Willd) DC. Samples were collected in residential households from Penga Penga and Kalebuka (a non-polluted suburb). The bioconcentration factor (BCF) and the safe weekly consumption (SWC) were calculated for each species. Results showed higher values of total and soluble concentrations of Cu, Pb, and Zn in the rhizosphere of the two species at Penga Penga. Metal concentrations were higher in fruits and leaves from Penga Penga with 47% of samples above FAO and WHO thresholds (vs 18.5% in Kalebuka). The BCF values were below 1 demonstrating the effectiveness of the process to reduce metal translocation to leaves and fruits. Recommendations from the SWC limited by Pb for consumption to 9 kg for mango flesh and by Cd 6.6 kg for S. guineense fruits at Penga Penga (Vs 78 and 68 kg at Kalebuka). Finally, results from this study provide interesting lessons from the scaling up and the technical itinerary of planting tree un Penga Penga.

This study provides a novel method to prepare metal-ceramic composites from magnetically selected iron ore using microwave heating. By introducing three different microwave susceptors (Activated Carbon, SiC, and a mixture of Activated Carbon and SiC) during the microwave process, effective control of the ratio of metallic and ceramic phases has been achieved easily. The effects of the three susceptors on the microstructure of the metal-ceramics and the related reaction mechanisms were also investigated in detail. The results show that the metal phase (Fe) and ceramic phase (Fe2SiO4, FeAl2O4) can be maintained, but the metal phase to ceramic phase changed significantly. In particular, the microstructures appeared as well-distributed nanosheet structures with diameters of ~400 nm and thicknesses of ~20 nm when SiC was used as the microwave susceptor.

This mini-review critically summarizes the knowledge of imprinted polymer-based electrochemical sensors, for the detection of pesticides, metal ions and waterborne pathogenic bacteria, focusing on the period the last 5 years (citation of 78 papers published in 2017-2021, ie 63% of total citations). MIP-based electrochemical sensors exhibit low limit of detection, high selectivity, high sensitivity and low cost. Herein, we focused on the timely topics of water pollution by organics, inorganics and micro-organisms represented by pesticides, metal ions and bacteria, respectively. We put the emphasis on the design of imprinted polymers and their composites and coatings by radical polymerization, oxidative polymerization of conjugated monomers or sol-gel chemistry. Whilst most imprinted polymers are used in conjunction with differential pulse or square wave voltammetry for sensing organics and metal ions, electrochemical impedance spectroscopy (EIS) appears as the chief technique for detecting bacteria. This successful combination of EIS and imprinting technology should be harnessed in the coming years in the case of bacteria. Interestingly, bacteria are not always probed by bacteria-imprinted polymers; we report here their detection by monitoring specific (macro)molecules that reflect bacterial activity, for example quorum sensing signaling molecules or flagella proteins. If much has been developed in the past decade with glassy carbon or gold electrodes, it is clear that carbon paste electrodes of imprinted polymers are more and more investigated due to their versatility. Shortlisted case studies were critically reviewed and discussed; clearly a plethora of tricky strategies of designing selective electrochemical sensors are offered to “Imprinters”. We anticipate this review will be of interest to experts and new comers in the field who are paying time and effort combining electrochemical sensors with MIP technology.

The Mediterranean Sea is one of the most impacted basin in terms of microplastics pollution. Land-based activities are the major sources of plastic litter to the ocean, with harbors probably representing significant hotspots. In the framework of the SPlasH! project (Stop alle Plastiche in H2O, Interreg Marittimo project), microplastics were sampled in three north-western Mediterranean harbors during summer and winter. In this study, the areal concentrations of microplastics ranged from 5,576 to 379,965 items.km-2. A decreasing gradient was observed from the inner to the outer zones of the studied harbors, pointing out these enclosed systems as hotspots regarding microplastic pollution. During the summer, because of an enhancement of port activities, the areal concentrations of microplastics were higher than in winter. The investigation microplastics size classes distribution in the surface waters revealed that microplastic within a size range between 300 µm and 500 µm were depleted. During this study, we assessed trace metal partitioning (Pb, Fe, Cu, V, Cd and As) between the dissolved phase and biofilm, thus highlighting concentrations within the biofilm two and six orders higher than those in the dissolved phase. This result strongly suggest trace metal bioaccumulation within the biofilm. When trace metal concentrations are normalized over the corresponding surface of microplastics and microplastics, higher values were obtained for microplastics evidencing their enhanced capacities to bioaccumulate contaminants with respect to macroplastics.

Zinc is a redox-inert trace element that is second only to iron in abundance in biological systems. In cells, zinc is typically buffered and bound to metalloproteins, but may also exist as a labile or chelatable (free ion) form. Zinc plays a critical role in prokaryotes and eukaryotes ranging from structural to catalytic to replication to demise. This review discusses the influential properties of zinc on various mechanisms of bacterial proliferation and synergistic action as anti-microbial element. We also touch upon the significance of zinc among eukaryotic cells and how it may modulate their survival and death through its inhibitory or modulatory effect on certain receptors, enzymes, and signaling proteins. A brief discussion on zinc chelators is also presented and chelating agents may be used with or against zinc to affect therapeutics against human diseases. Overall, the multidimensional effects of zinc in cells attest to the growing numbers of scientific research that reveal the consequential prominence of this remarkable transition metal in human health and disease.

The copper deposition on the platinum and palladium nanoelectrode has been studied using cyclic voltammetry. The use of nanoelectrode platinum and palladium are defined in the study of heavy metals. The noble nanoelectrode of metal has a typical silicone processing structure. In comparison to the nanoelectrodes, the geometry of the electrode series is complex and balanced. Nanoelectrodes of platinum are found effective in detecting heavy metal. There was regular analysis of the use of the sensors. The identification constraints down to the ng /L level was accomplished by refined electrode geometry and the stripping procedures. The process was used for the study of water sample determination. Another heavy metal ion attack voltammetric reaction was studied. The SEM picture clearly observed and characterized the nanoparticle electrode by X-ray diffraction and cyclic voltammetry.

Heavy metals, including arsenic from abandoned mines, are easily transported with sediment and deposited in water bodies such as reservoirs and lakes, creating critical water quality issues when they are released. Understanding the leaching of heavy metals is necessary for developing efficient water quality improvement plans. This study investigated how arsenic leaches from different soil types and responds to hydrologic conditions to identify areas susceptible to arsenic contamination. In this study, batch- and column-leaching tests and sequential extraction procedures were used to examine arsenic leaching processes in detail. The results showed that most arsenic-loaded sediments accumulated in the vicinity of a reservoir inlet, and arsenic in reservoir beds have a higher leaching potential than those from agricultural land and river beds. Arsenic deposited at the bottom of reservoirs had higher mobility than that in the other soils, and arsenic leaching was closely associated with the acidity of water. In addition, arsenic leaching was found to be responsive to seasons (wet or dry) as its mobilization is controlled by organic compounds that vary over time. The results suggested that temporal variations in the hydrochemical composition of reservoir water should be considered when defining a management plan for reservoir water quality.

Heavy metal pollution is an increasing global concern. Among heavy metals, mercury (Hg) is especially dangerous because of its massive release into the environment and high toxicity, especially for aquatic organisms. The molecular response mechanisms of algae to Hg exposure are mostly unknown. Here, we combine physiological, biochemical, and transcriptomic analysis to provide, for the first time, a comprehensive view on the pathways activated in Chromera velia in response to toxic levels of Hg. Production of hydrogen peroxide and superoxide anion, two reactive oxygen species (ROS), showed opposite patterns in response to Hg²⁺ while reactive nitrogen species (RNS) levels did not change. A deep RNA sequencing analysis generated a total of 307,738,790 high-quality reads assembled in 122,874 transcripts, representing 89,853 unigenes successfully annotated in databases. Detailed analysis of the differently expressed genes corroborate the biochemical results observed in ROS production and suggests novel putative molecular mechanisms in the algal response to Hg²⁺. Moreover, we indicated that important transcription factor (TF) families associated with stress responses differentially expressed in C. velia cultures under Hg stress. Our study presents the first in-depth transcriptomic analysis of C. velia, focusing on the expression of genes involved in different detoxification defense systems in response to heavy metal stress.

The remediation of dredged marine sediments contaminated by heavy metals has drawn increasing attention worldly. The immobilization was regarded as a promising method to reduce adverse impacts on marine ecosystem. In this study, kaolinite and limestone were used as amendments to immobilize heavy metals (e.g. Zn, Pb and Cu) respectively in dredged marine sediments collected from the coastal zone adjacent to Tianjin Port in Bohai Bay. The sequential extraction procedure was applied to identify the mobility of heavy metals and further to evaluate the immobilization effect of amendments. The physical-chemical properties of sediments, such as pH, electrical conductivity (EC), salinity, and total organic carbon (TOC), were also measured to better understand their influence on heavy metals’ mobility. In addition, the compositions of clay minerals were also analyzed to identify the transformation process of minerals in the sediments. The results of sequential extraction procedure indicated that mobile fractions of heavy metals were converted into relatively stable fractions because of the two amendments. In addition, EC, salinity and TOC decreased moderately while no obvious variations of pH in the sediments were observed with the addition of the the kaolinite and the limestone. The percentage of montmorillonite decreased to minimum value while that of chlorite increased gradually during the experimental periods for 40 days probably due to complexation reaction. It was confirmed that both kaolinite and limestone can effectively reduce the mobility and bioavailability of heavy metals, particularly for Zn, generally, limestone has a better immobilization effect compared with kaolinite.

Hetero-nanomaterials constructed by plasmonic metals and functional semiconductors show enormous potential in photocatalytic applications, such as water splitting, hydrogen production, CO₂ reduction, pollutants treatment. Their photocatalytic performances can be better regulated through adjusting structure, ingredient, and components arrangement. Therefore, the reasonable design and synthesis of metal/semiconductor hetero-nanostructures is of vital significance. In this article, we briefly review the recent progress in efficiently establishing metal/semiconductor nanomaterials for improved photocatalysis. The defined photocatalysts mainly include traditional binary hybrids, ternary multi-metals/semiconductor and metal/multi-semiconductors heterojunctions. The underlying physical mechanism for the improved photocatalytic activity of the established photocatalysts are highlighted. At the end of this article, a brief summary and possible future perspectives for further development in this field are demonstrated.

ASTM A743 CA6NM alloy is a martensitic stainless steel typically used in energy industry -runners and hydraulic turbine components- due to its superior toughness, yield and fatigue properties. In both the manufacturing, shielded metal arc welding is applied to join for this grade steels. However, weldability of the steels is limited due to formation of hard and brittle phases such as untempered martensite during welding and post weld heat treatment processes. The formation causes a reduction in toughness. In this study, influence of post-weld heat treatment procedure (single tempering and double tempering) and parameters on microstructure and hardness of AWS410NiMo all weld metal. Hardness tests were conducted from weld metal. Microstructures of the all weld metals subjected to different heat treatment process were characterized.

In recent years, the need for safe and modern composite barrier for the prevention of groundwater contamination and the provision of Geo-environmental protection has been studied together with the need of designing low cost and effective liner for isolating landfill contents from the environment. In this study, various mix designs involving two natural adsorbents, the Na-Bentonite and the pH-adjusted sawdust were prepared for a series of Geo-environmental experiments to be carried out to determine the adsorption capacity, buffering capacity, pH changes, and COD changes among others, in the presence of Pb(NO3)2 contaminant concentrations. Generally, the results showed an increase in adsorption capacity in the acidic segment of the treatment. An increase of 58% of the adsorption efficiency of the Na-Bentonite in adsorbing the contaminant at the highest concentration was the most important achievement of the system while in the acidic segment.

A simple, efficient and stand-alone method for purification of river water using moringa seed powder and copper is discussed. Coagulant property of the seed powder clears turbid raw water and the oligodynamic activity of copper completely destroys E.coli bacteria. Both raw and treated water samples were tested for contaminants to verify the efficacy of the system. Treated water has turbidity in the range 3 NTU - 5 NTU and non-detected (< 1 MPN/100 mL) E.coli count making it suitable for drinking. The technique is very cost effective and can be practiced anywhere using locally available materials. It does not require a power source or any technical assistance. Being a stand-alone system the technique exceptionally useful in providing drinking water as an immediate solution in disaster areas affected by cyclone or floods.

Bottom-up synthesis of porous NiMo alloy reduced by NiMoO₄ nanofibers was systematically investigated to fabricate non-noble metal porous electrodes for hydrogen production. The different annealing temperatures of NiMoO₄ nanofibers under hydrogen atmosphere reveal that the 950 °C annealing temperature is a key to produce bicontinuous porous NiMo alloy without oxide phases. The porous NiMo alloy as cathodes in electrical water splitting demonstrates not only almost identical catalytic activity with commercial Pt/C in 1.0 M KOH solution, but also superb stability for 12 days at an electrode potential of −200 mV (v.s. RHE).

Hepcidin-25 was identified as the main iron regulator in the human body by binding to the sole iron-exporter ferroportin. Studies showed that the N-terminus of hepcidin is responsible for this interaction, the same N-terminus that encompasses a small copper(II)-binding site known as ATCUN (amino terminal Cu(II)- and Ni(II)- binding) motif. Interestingly, this copper-binding property is largely ignored in most papers dealing with hepcidin-25. In this context, detailed investigations of the formed complex of hepcidin-25 with copper could reveal insights into its biological role. The present work is mainly focused on the study of the metal-bound form of hepcidin-25, which could be considered the biologically active form. The first part is devoted to the reversed-phase chromatographic separation of copper-bound and copper-free hepcidin-25, which was achieved by applying basic mobile phases containing 0.1% ammonia. Further, mass spectrometry (tandem mass spectrometry MS/MS, high resolution mass spectrometry HRMS) and nuclear magnetic resonance (NMR) spectroscopy were employed to characterize the copper-peptide. Lastly, a 3D model of hepcidin-25 with bound copper(II) is presented. The identification of metal complexes and potential isoforms and isomers, from which the latter usually are left undetected by mass spectrometry, led to the conclusion that complementary analytical methods are needed to characterize a peptide calibrant or reference material comprehensively. Quantitative nuclear magnetic resonance (qNMR), inductively-coupled plasma mass spectrometry (ICP-MS), ion-mobility spectrometry (IMS) and chiral amino acid analysis (AAA) should be considered among others.

To address the complex challenges posed by climate change and its effects on surface environments, subsoil, and groundwater, evaluating the impacts of Degradation-Resistant Organic Compounds (DROCs), such as fats and oils, is crucial. Increasing variability in temperature and precipitation has exacerbated DROC dispersal, particularly near open dumps and poorly managed landfills. As a global pollution issue, DROC’s pervasive and persistent nature requires urgent attention. This study aims to develop and implement effective strategies to detect and describe the stages of DROC decomposition. Identifying sites where DROCs are trapped and their dispersion can facilitate planning remediation efforts and mitigating adverse effects on ecosystems and human health. The study focuses on evaluating DROCs’ annual spatiotemporal distribution, improving waste management practices, monitoring the subsoil, and implementing remediation strategies. DROCs persist through various stages in groundwater, making effective detection methodologies essential. Continuous monitoring, subsoil characterization, and diverse climatic observations are necessary, especially in areas with improper landfill selection. Poor waste management contributes significantly to DROC pollution, exacerbated by current consumerism and increasing waste. The research highlights the importance of improving waste management practices and judiciously selecting landfill sites to prevent further degradation. Apparent resistivity variations in the subsoil, linked to DROC dispersal, are analyzed to map affected areas and understand propagation under different environmental conditions. New tools and methodologies aim to enhance DROC monitoring and remediation strategies. Adopting sustainable waste management practices and carefully selecting disposal sites is essential to mitigating DROC’s impacts, reducing greenhouse gas emissions, and protecting environmental and public health. Addressing risks associated with excessive consumption, inadequate waste management, and poor landfill selection is crucial for restoring ecosystem resilience and environmental protection.

Life Cycle Assessment (LCA) is a widely used tool to measure the environmental sustainability of products or processes. Integrating LCA into the assessment of waste diversion strategies recognizes current waste diversion strategies are insufficient to effectively stem the global impacts of waste particularly with increased pressure to recover organic and inorganic materials to reduce landfill impacts and promote the circular economy. Historically, waste diversion efforts in municipalities and industries focused on higher-profile inorganic wastes, such as plastics and other recyclables. However, organic waste is increasingly identified as a key waste fraction that must be effectively managed and regulated. This research surveys published LCA studies from 2019 to 2023 focusing on the anaerobic digestion (AD) of organic waste. Notable conclusions include the lack of studies comparing AD with the latest treatment options such as co-gasification; the insufficient attention to the LCAs on biogas upgrading methods; and the monetization of LCA results using carbon credits. In addition, more than 50% of reviewed LCA studies concluded the results with a sensitivity analysis which was not a common practice before 2019 in LCA studies in anaerobic digestion. This signifies the increasing need to understand uncertainty in the circumstances governing applying AD to wastes. Finally, neglecting the combined effect of several parameters in sensitivity analysis might have reduced the accuracy of the sensitivity analyses in the reviewed LCAs. Overall, LCAs conducted on AD-related applications vary widely in terms of scope and consistency, implying that the outcomes may not be as applicable as intended. The identified challenges, issues, and other findings related to this research are expected to help standardize LCA procedures as applied to AD to promote greater comparability.

This study examines the Soil Organic Carbon (SOC) within Greek croplands, offering a comprehensive understanding of its dynamics. SOC, a cornerstone in soil health, nutrient cycling, and global carbon dynamics, assumes critical significance in sustainable agriculture and climate change mitigation. Drawing on diverse soil properties, including pH, soil texture as well as different drainage and slope categories, the research explores the nuanced relationships shaping SOC dynamics in the diverse agroecological landscape of Greece. The investigation transcends local boundaries, emphasizing SOC's global role in climate change mitigation by sequestering carbon dioxide. Two maps were used as data sources: 1) SOC stock baseline map (2010) by JRC, 2) SOC stock map (2021) by the Institute of Soil and Water Resources, Hellenic Agricultural Organization – DIMITRA in collaboration with FAO. Greek croplands emerge as a mosaic of agroecological diversity, where anthropogenic activities wield transformative influences on SOC stock, demanding a delicate balance between agricultural productivity and soil health. The study unveils the influence of Soil Order, weaving a tapestry of SOC variability. Microscopic factors, from soil texture to cation exchange capacity, further shape SOC dynamics, emphasizing the role of clayey soils and coarse materials in carbon retention. Although soil organic carbon decreased from 2010 to 2021 the degree of carbon loss varied. This scientific endeavor synthesizes existing knowledge and unveils novel insights, offering a narrative woven from diverse soil properties. The findings contribute valuable insights for sustainable land management practices and climate change mitigation strategies, underscoring the importance of region-specific approaches in addressing global challenges.

This study analyzed the anaerobic co-digestion of Inoculum (I), Rubber Plant Effluent (RPE) and Gliricidia leaves (GLS) at different mixing ratios for the simultaneous production of methane and organic fertilizer. The results were analyzed for volatile fatty acids, pH, C/N ratio, and methane production. The organic quality of the substrate mixture before and after anaerobic digestion was analyzed for organic carbon, Kjeldahl nitrogen, potassium, and phosphorus content. The study concluded that the inoculum, Rubber Plant Effluent (RPE), and Gliricidia leaves (GLS) mixed in the ratio of 10:2:2 showed higher methane production than other experiments conducted at different mixing ratios. The nitrogen, Potassium and phosphorus content of the substrates are increased after anaerobic digestion. However, the organic carbon content in the substrate decreased in all experiments. This research recommends the planting of rubber trees and Gliricidia maculata to promote economic development in Mauritania. Keywords: Biogas production; Gliricidia leaves; Methane; Rubber Plant Effluent; Organic Manure

Gold nanohole arrays are periodic metastructures gathering huge interest for biosensing applica-tions. The grating-like structure defines their plasmonic mode features and their angular disper-sion can be used to highlight efficiently their interaction with the fluorescence emission of a properly tuned fluorophore. Resorting to a properly tuned/engineered/optimised plasmonic na-nohole array and a commercial organic dye, we performed an accurate resolved angle-resolved optical characterization. The plasmonic fingerprints was consequently identified as a modification of the dye photoluminescence signal in terms of both spectral redistribution and enhancement. Interestingly, by analyzing the results, an advantageous measurement configuration can be iden-tified to better engineer a suitable platform for efficiency maximization in plasmon-enhanced flu-orescence-based applications. Therefore, the coupling mechanism with the plasmonic modes, and nanostructure properties can be carefully co-optimized.

Organic agriculture based on participatory guarantee system (PGS) has been promoted as a tool for sustainable ecosystem, self-reliance and poverty alleviation of smallholder farmers in Thailand. However, specific criteria are required to certify as organic products. In this paper, the researchers present the collaboration of smallholder farmers practicing organic farming based on participatory guarantee system in four Thai provinces: Nong Bua Lam Phu, Nakhon Phanom, Ubon Ratchathani and Nakhon Ratchasima. One hundred thirty-five smallholder farmers were purposively selected as the informants. In depth interviews were conducted to conceptualize. The participatory guarantee system management considering their diverse agricultural background and socio-economic conditions. Main findings concluded that motivations for PGS were restoration soil quality and decreasing yield. Key factors for sustainable adaptation are policy support in terms of financial measures and capacity building.

Bioactive compound profiles in organic and conventional sweet basil were analyzed by HPLC, and the enzymatic status and antioxidant status of plants cultivated with the two systems were also examined. Unique chemical compound locations in the basil leaves were also estimated by fluorescence microscopy. The experiment was conducted from 2019-2021. Organic and conventional basil samples were obtained directly from the largest Polish herb producers. The results showed that the chemical structures of organic and conventional basil leaves are different. Not only cultivation method but also experimental year had a significant impact on the antioxidants content in basil leaves. Organic basil contained significantly more dry matter (11.97 g 100 g-1 FW) compare to conventional one (10.54 g 100g-1 FW) and showed a higher tendency for total phenolic (5.24 mg g -1 DW) concentrations than conventional basil (4.99 mg g-1 DW). The higher bioactive compound content reflects the antioxidant activity ( 61.0%, 54.33% and 46%) in organic basil compare to conventional 46.87%, 38.055 and 39.24%), respectively to analysis method (ABTS, DPPH and FRAP), as well catalase activity (39 µmol H2O2 min-1 mg-1) in organic compare to conventional (23.19 µmol H2O2 min-1 mg-1) of examined basil plants. The obtained results are a very unique and could be used by herbs producers as a key for q high quality basil production.

Diversification in agroecosystems can increase the sustainability of agricultural production and reduce input dependence in agroecological transitions. This study evaluated the effects of intercropping and the introduction of flowering (aromatic) plant strips on the ratio of land use efficiency and crop damage for broccoli and lettuce association. Two experiments were conducted in 2022 and 2023 in experimental plots in southwestern Colombia. Crop association alone did not impact crop yield; the production was higher in the lettuce monoculture. However, in the presence of flowering plant strips, the land use equivalent ratio (LER) is &gt;1 in the two years of study, with a high yield for broccoli. Regarding the damage by the silverback moth Plutella xilostella L on broccoli, no differences were found between crops established with or without flower strips. Similarly, flower strips did not affect the incidence of lettuce rot caused by Sclerotinia spp. In summary, our results support the idea that farmers can introduce flower strips into their horticultural fields to improve the eco-productive efficiency of their farms and reduce dependence on external polluting inputs. However, further research is needed to clarify the mechanisms underlying these results.

Two-phase olive pomace is a byproduct of the olive-oil extraction process that is sometimes processed further to recover more oil. During pomace oil production, especially in the early stages of olive processing, odours can be produced. These odours are a serious nuisance especially in and around the processing facilities, as well as for nearby communities. These odours can be strong and unpleasant, and they may result in various issues, including environmental concerns. Thus, in this paper, the effect of storage and drying on the composition of two-phase olive pomace was investigated. Several physicochemical and instrumental analyses were performed and it was concluded that the structural elements of pomace are not the ones who are affected during storage and drying. Storage and drying mainly impact the oil content of pomace, leading to an acidity increase and to the production of odorous oxidation compounds. Volatile acids, methyl and ethyl esters are released into the atmosphere causing serious environmental nuisance.

We measured the anelastic, dielectric and structural properties of the metal-free molecular perovskite (ABX$_{3}$) (MDABCO)(NH$_{4}$)I$_{3}$, which has already been demonstrated to become ferroelectric below $T_{\text{C}}=$ 448~K. Both the dielectric permittivity measured in air on discs pressed from powder and the complex Young's modulus measured on resonating bars in vacuum show that the material starts deteriorating with loss of mass just above $T_{\text{C}}$, introducing defects and markedly lowering $T_{\text{C}}$. The elastic modulus softens of 50\% when heating through the initial $T_{\mathrm{C}}$, contrary to usual ferroelectrics, which are stiffer in the paraelectric phase. This suggests improper ferroelectricity, where the primary order parameter of the transition is not the electric polarization, but the orientational order of the MDABCO molecules. The degraded material presents thermally activated relaxation peaks in the elastic energy loss, whose intensities increase together with the decrease of ~$T_{\mathrm{C}}$. The peaks are much broader than pure Debye, due to the general loss of crystallinity, also apparent from X-ray diffraction, but their relaxation times have parameters typical of point defects. It is argued that the major defects should be of the Schottky type, mainly due to the loss of (MDABCO)$^{2+} $ and I$^{-}$, leaving charge neutrality, and possibly also (NH$_{4}$)$^{+}$ vacancies. The focus is on an anelastic relaxation process peaked around 200~K at $\sim 1$~kHz, whose relaxation time follows the Arrhenius law with $\tau $$_{0}$~$\sim $\ $10^{-13}$\ s and $E\simeq 0.4$~eV. This peak is attributed to I vacancies (V$_{\text{X}}$) hopping around MDABCO vacancies (V$_{\text{A}}$) and its intensity presents a peculiar dependence on temperature and content of defects. The phenomenology is thoroughly discussed in terms of lattice disorder introduced by defects and of partition of V$_{\text{X}}$ among sites that are far from and close to the cation vacancies. A method is proposed for calculating the relative concentrations of V$_{\text{X}}$, that are untrapped, paired with V$_{\text{A}}$ or forming V$_{\text{X}}$--V$_{\text{A}}$--V$_{\text{X}}$ complexes.

Microbial pigments have many structures and functions with excellent characteristics, such as being biodegradable, non-toxic, and ecologically friendly, constituting an important source of pigments. Industrial production presents a bottleneck in production cost that restricts large-scale commercialization. However, microbial pigments are progressively gaining popularity because of their health advantages. The development of metabolic engineering and cost reduction of the bioprocess using industry by-products opened possibilities for cost and quality improvements in all production phases. We are thus addressing several points related to microbial pigments, including the major classes and structures found, the advantages of use, the biotechnological applications in different industrial sectors, their characteristics, and their impacts on the environment and society.

The objective of this was to evaluate the effects of organic fertilization on biomass production in Urochloa spp. pastures, and the soil biological and physical properties in the Colombian Amazon region. Three pastures crops (Urochloa decumbens, Urochloa humidicola and Urochloa brizantha) with 5 years old were examined in a hill landscape. A randomized complete blocks design covering an area of 5005 m2, with 1 m separation between units to minimize edge effects. Highly significant differences in Urochloa spp. biomass production were observed before and after organic fertilization (i.e., initial time: 992.19±97.66 kg DM ha-1 vs. final time: 1920.94±155.44 kg DM ha-1 vs.), but not between different fertilization treatments. The interaction between the treatment and time was significant for total density (p=0.0300) and richness (p=0.0300) of soil macrofauna. Furthermore, the interaction between treatment and soil depth was significant for bulk density (p=0.0187). The linear mixed effects analysis showed that soil bulk density and penetration resistance were lower in 0 - 10 cm depth than that observed in 10 - 20 depth and 20 - 30 cm depth. Overall, the application of organic fertilizers had a significant and positive effect on Urochloa spp. forage biomass and on the physical and biological properties of soils that had historically been affected by extensive livestock farming in a deforested hill landscape in the Colombian Amazon region.

Agricultural soils serve as crucial storage sites for soil organic carbon (SOC). Their appropriate management is pivotal for mitigating climate change. To evaluate spatial and temporal changes in SOC within agricultural fields, continuous monitoring is imperative. In-field data sets of Vis-NIR soil spectra were collected on a long-term experimental site using an on-the-go spectrophotometer. Data processing for continuous SOC prediction involves a two-steps modelling approach. In Step 1, a Partial Least Square (PLSR) regression model is trained to establish a relationship between the SOC content and the spectral information also including spectral preprocesisng. In Step 2, the predicted SOC content obtained from the PLSR models is interpolated using ordinary kriging. Among the tested spectral preprocessing techniques and semivariogram models, SG and gapDer preprocessing along with a Gaussian semivariogram model, yielded the best performance resulting in a root mean square error of of 1.24 and 1.26 g kg-1. A striping effect due to the transect-based data collection was addressed by testing the effectiveness of extending the spatial separation distance, employing data aggregation, and defining the distribution based on treatment plots using block kriging. Overall, the results highlight the immense potential of on-the-go spectral Vis-NIR data for field-scale spatial-temporal monitoring of SOC.

Magnaporthe oryzae Triticum (MoT) pathotype is the causal agent of wheat blast, which has caused significant economic losses and threatens wheat production in South America, Asia and Africa. Three bacterial strains from rice and wheat seeds (B. subtilis BTS-3, B. velezensis BTS-4, and B. velezensis BTLK6A) were used to explore the antifungal effects of volatile organic compounds (VOCs) of Bacillus spp. as a potential biocontrol mechanism against MoT. All bacterial treatments significantly inhibited both mycelial growth and sporulation of MoT in vitro. We found that this inhibition was caused by Bacillus VOCs in a dose-dependent manner. In addition, biocontrol assays using detached wheat leaves infected with MoT showed reduced leaf lesions and sporulation compared to the untreated control. VOCs from B. velezensis BTS-4 alone or a consortium (mixture of B. subtilis BTS-3, B. velezensis BTS-4, and B. velezensis BTLK6A) treatments consistently suppressed MoT in vitro and in vivo. Compared to the untreated control, VOCs from BTS-4 and Bacillus consortium reduced MoT lesions in vivo by 85% and 81.25%, respectively. A total of thirty-nine VOCs (from 9 different VOC groups) from 4 Bacillus treatments were identified by gas chromatography-mass spectrometry (GC-MS), of which 11 were produced in all Bacillus treatments. Alcohols, fatty acids, ketones, aldehydes, and S-containing compounds were detected in all four bacterial treatments. In vitro assays using pure VOCs revealed that hexanoic acid, 2-methylbutanoic acid, and phenylethyl alcohol are potential VOCs emitted by Bacillus spp. that are suppressive for MoT. The minimum inhibitory concentrations for MoT sporulation were 250 mM for phenylethyl alcohol and 500 mM for 2-methylbutanoic acid and hexanoic acid. Therefore, our results indicate that VOCs from Bacillus spp. are effective compounds to suppress the growth and sporulation of MoT. Understanding the MoT sporulation reduction mechanisms by Bacillus VOCs may provide novel options to manage the further spread of wheat blast by spores.

Abundant animal manure in livestock areas has the potential to be used as organic fertilizer which can restore soil fertility by turning it into compost and biochar. The goal of this study was to as-sess how well soil fertility and red chili yield might be increased by using biochar and poschar made from various animal wastes. In this investigation, a factorial pattern and randomized block design were used. The first factor was the biochar treatment type, which included no biochar, biochar made from cow manure, biochar made from goat manure, and biochar made from chicken manure. The second factor was the type of poschar, which included no poschar, poschar made from cow manure, poschar made from goat manure, and poschar made from chicken manure. The findings of this study suggest that using biochar in conjunction with poschar can significantly improve soil parameters such as soil water content, pH, EC, humic acid, fulvic acid, C, N, P, K, and CEC. Red chilies grow and yield more per hectare when different types of biochar and poschar are used. The use of biochar from cow manure together with poschar from chicken manure shows the best agronomic effectiveness.

The study was carried out to investigate the growth response of Tetrapluera tetraptera to selected organic fertilizers. Organic fertilizers: poultry manure and cow dung of different concentration and mixture were used to raise seedlings from Germination experiment for a period of 12 weeks. Six treatments were used for this research: T1 (control experiment), T2 (10g of poultry manure), T3 (10g of cow dung), T4 (20g of poultry manure), T5 (20g of cow dung), T6 (15g of poultry manure + 15g of cow dung). Growth parameters such as diameter, plant height and number of leaves were measured weekly over a period of twelve (12) weeks. Data obtained were subjected to Anova and mean separated using Duncan multiple range tests. on the height parameter assessed on Tetrapluera tetraptera, the highest plant height mean of 12.20cm was recorded in treatment 6 (15g of poultry manure + 15g of cow dung) while the lowest mean plant height 7.19cm was recorded in treatment 3 (10g of cow dung) . the highest mean stem diameter was recorded in treatment 4 with a value of 0.43mm from while the least was recorded in Treatment 1 with mean value of 0.21 m. also, highest mean number of leaves was recorded treatment 4 (12.81) while the least was observed in T3 (11.01) . The results showed that organic manure has considerable effect on the growth of Tetrapluera tetraptera seedlings and it use should be encouraged. T3 (10g of poultry Manure + 10g of cow dung) was hereby recommended to be the best of all in the growth of Tetrapluera tetraptera.

The study investigated the comparative effect organic fertilizers on the growth of Khaya senegalensis (Desr). Four treatments were used for this research: T1 20g of poultry manure, T2 (20g of cow dung), T3 (10g of poultry Manure + 10g of cow dung), T4 (Control experiment). Growth parameters such as diameter, plant height and number of leaves were measured weekly over a period of twelve (12) weeks. Data obtained were subjected to ANOVA and mean separated using Duncan Multiple Range Test. on the height parameter assessed on Khaya Senegalensis, the highest plant height mean of 8.40cm was recorded in treatment 1(20g of poultry Manure) while the lowest mean plant height 7.19cm was recorded in treatment 4 (Control experiment). Also, the highest mean stem diameter was recorded in Treatment 1 with a value of 0.309mm from while the least was recorded in Treatment 4 with mean value of 2.1175mm. However, highest mean number of leaves was recorded treatment 1 (20g of poultry manure) while the least was observed in T3 (10g of poultry Manure + 10g of cow dung). The results showed that organic manure has considerable effect on the growth of Khaya senegalensis seedlings and it use should be encouraged. T3 (10g of poultry Manure + 10g of cow dung) is hereby recommended to be the best of all in the growth of Khaya senegalensis.

Is the production of the “AnchoisFert” organic fertilizer via the circular economy process based on omega-3 lipid extraction of milled anchovy fillet leftovers with citrus limonene followed by mild drying economically and technically viable? This study answers this question and identifies the main obstacles, chiefly of economic and organizational nature, to be overcome prior to commercialization of this new organic fertilizer. Along with non-variable and proven efficacy, successful competition with conventional organic and inorganic fertilizers requires affordable cost and regular supply. This, inter alia, requires to establish new and mutually beneficial relationship between bioeconomy firms and fish processing companies.

Miombo woodlands are extensive dry forest ecosystems in central and southern Africa covering ≈2.7 million km2. Despite their vast expanse and global importance for carbon storage, the long-term carbon stocks and dynamics have been poorly researched. The objective of this paper is to present and summarize the evidence gathered on above- and belowground (root and soil) carbon stocks of miombo woodlands from the 1960s to mid-2018 through a review. We analyzed data to answer: (1) What is the range of aboveground and belowground carbon stocks found in miombo woodlands over the last six decades? (2) Are there differences in carbon stocks based on land-management categories? (3) Does precipitation influence aboveground carbon stocks in old-growth miombo? (4) Do differences in cover type, age and region influence carbon stocks? (5) How does previous land-use affect carbon stocks in re-growth miombo? A literature review protocol was used to identify 56 publications from which quantitative data on aboveground and soil carbon pools were extracted. We found that the mean aboveground carbon stock in old-growth miombo was 30.83±16.76 Mg C ha-1 (range 1.48—107.24 Mg ha-1). Old-growth miombo had an average calculated root carbon stock of 16.49±9.18 Mg C ha-1 (range 0.8—57.81 Mg ha-1). Soil carbon stocks in old-growth miombo varied widely, between 8.75 and 134.6 Mg C ha-1 while in re-growth miombo they varied between 10.73 and 52.2 Mg C ha-1. It must be noted these soil data are given only for information; they inconsistently refer to varying soil depths and are thus difficult to interpret. The wide range reported suggests a need for further studies, much more systematic in methods and reporting. Other limitations of the dataset include the lack of systematic sampling and lack of data in some countries, viz. Angola and Democratic Republic of the Congo.

Produced in many world’s countries at over 1 million tonne/year rate by extraction of certain woods and barks with boiling water, tannin is a class of high molecular weight biophenols increasingly used in a number of industries. This study offers a new bioeconomy insight into an old natural product that, we argument in this study, will play a crucial role in the development of the bioeconomy of forest regions. After providing an updated picture of key economic and production aspects, we show how flourishing research on tannin’s biological activity and technological applications has revealed many new properties which are likely to drive significant growth in demand in the near and mid-term future. The study concludes with selected recommendations for bioeconomy scholars and for policy-makers based in forest areas.

Society considers wine as a special product among food and beverages because of its high gastronomical value and its positively distinctive quality. In recent years, philosophies of the agricultural techniques and development of the oenological technology have been focused on the reduction of wasteful, "polluting" elements, and trends are moving towards an environmental friendly approach. Due to the stricter regulations and rules (with the limited amount and selection of the permitted chemicals) resistant, also known as interspecific or innovative grape varieties can be the ideal basic materials of alternative cultivation technologies. In terms of variety selection, innovative varieties can be equivalent to international varieties, although organically their quality could not compete with them. These grapes are more resistant to various fungal diseases and infections than international varieties. Well-founded analytical and organoleptic results have to provide the scientific background of resistant varieties, as these cultivars with the environmental friendly cultivation techniques, could be the raw material of the future.

The changes in nutritional quality, bioactive compounds and antioxidant enzymes in the juice of four blood orange cultivars (‘Moro’, ‘Tarocco’, ‘Sanguinello’ and ‘Sanguine’) stored during 6 months at 2 and 5 °C plus 2 days at 20 °C for shelf life were studied. Sucrose was the sugar found at higher concentration and decreased during storage for all cultivars, as did glucose and fructose. Organic acids decreased at both temperatures and the highest content was found in ‘Sanguinello’, especially the major (citric acid) and ascorbic acid. Total phenolics content (TPC), total anthocyanins (TAC), and the individual (cyanidin 3-glucoside and cyanidin 3-(6″-malonylglucoside)) increased for all cultivars, the ‘Sanguinello’ having the higher concentrations. Antioxidant enzymes catalase (CAT), ascorbate peroxidase (APX) and superoxide dismutase (SOD) were higher also in ‘Sanguinello’ and increased during storage. Overall, these results together with the sensory analysis suggest that ‘Sanguinello’ would be the best cultivar for prolonged storage.

The market of natural and organic cosmetics has been growing in last decades. The increase in interest in this type of product is a consequence of the concern that consumers have been presenting in relation to the environment and health. In addition to the appreciation the use of sustainable ingredients in cosmetic formulations, the consumers are also concerned about pollution caused by the use of plastics, which leads industries to reinvent themselves and rethink about the composition of packaging. The factor that most drives the purchase of natural and organic cosmetics is the fact that the consumer, in addition to contributing to the preservation of the environment, is also using a sustainable product. The growing demand for natural and organic cosmetics results in a concern of the brands with the organic issue, with the decreased use of animal derived ingredients and with the updating the parameters required for certification of a cosmetic as natural or organic. Due to the few studies available in this area, the importance of clarifying the definitions and concepts of natural and organic cosmetics is evident, in order to contribute with accurate information for the cosmetic sector.

Chemical processing of organic material in aqueous atmospheric aerosols and cloudwater is known to form secondary organic aerosols (SOA), although the extent to which each of these processes contributes to total aerosol mass is unclear. In this study, we use GAMMA 5.0, a photochemical box model with coupled gas and aqueous-phase chemistry, to consider the impact of aqueous organic reactions in both aqueous aerosols and clouds on isoprene epoxydiol (IEPOX) SOA over a range of pH for both aqueous phases, including cycling between cloud and aerosol within a single simulation. Low-pH aqueous aerosol, in the absence of organic coatings or other morphology which may limit uptake of IEPOX, is found to be an efficient source of IEPOX SOA, consistent with previous work. Cloudwater at pH 4 or lower is also found to be a potentially significant source of IEPOX SOA. This phenomenon is primarily attributed to the relatively high uptake of IEPOX to clouds as a result of higher water content in clouds as compared to aerosol. For more acidic cloudwater, the aqueous organic material is comprised primarily of IEPOX SOA and lower-volatility organic acids. For both cloudwater and aqueous aerosol, pH is the most significant factor considered in this study in determining the mass of aqueous phase organic acids and IEPOX SOA. Other factors, such as the time of day or sequence of aerosol-to-cloud or cloud-to-aerosol transitions, contribute to less than 15% difference in the final aqSOA fractional composition. The potential significance of cloud processing as a contributor to IEPOX SOA production could account for discrepancies between predicted IEPOX SOA mass from atmospheric models and measured ambient IEPOX SOA mass, or observations of IEPOX SOA in locations where mass transfer limitations are expected in aerosol particles.

The study of the distribution and health risk assessment is meaningful to provide basic data for environmental management．To investigate the pollution of potential toxic organics and their health risk to human beings, water samples were collected at 7 sites of main surface water of Beijing during wet and dry seasons respectively. The targeted 92 organics were detected, including phthalates (PAEs), volatile organic compounds (VOCs), polycyclic aromatic hydrocarbons (PAHs) and phenols. The results showed that: there were 56 organics detected out, and the number ratios of detected compounds to the total compounds of the same kind increased as the following: VOCs, phthalates, phenols, PAHs. 8 VOCs were detected in wet season, and 3 in dry season. The concentration of 2,2-Dichloropropane was highest as 10.62ug/L, while the concentrations of other VOCs were below 5ug/L; There were 11 phthalates detected during dry season. The content of Bis(2-methoxyethyl) phthalate was highest as 188.47ng/L; 17 phenols were found in samples during wet season, and the highest concentration was 1244.73ng/L for 4-nitrophenol; PAHs could be detected in all samples, and the detected compounds and the corresponding average concentrations were higher in wet seasons than those in dry seasons, which indicated that non-point pollution was possibly the main pollution source. The health risk assessment of the detected 56 pollutants by using a model from US EPA showed that, the risk caused by the four kinds of toxic organics in this study was in the acceptable ranges.

The consideration toward Waste Cooking Oils (WCOs) is changing from hazardous waste to valuable raw material for industrial application. During the last five years some innovative processes based on the employment of recycled WCO have appeared in the literature. In the present review article, the most recent applications of recycled Waste Cooking Oil are reported and discussed. These include the production of bio-plasticizers, the application of chemicals derived from WCOs as energy vectors, and the use of WCOs as solvent for pollutant agents.

Photovoltaic is one of the promising renewable sources of power to meet the future challenge of energy need. Organic and perovskite thin film solar cells are an emerging cost-effective photovoltaic technology because of low-cost manufacturing processing and a light-weight. The main barrier of commercial use of organic and perovskite solar cells is the poor stability of devices. Encapsulation of these photovoltaic devices is one of the best ways to address this stability issue and enhance the device lifetime by employing materials and structures that possess high barrier performance for oxygen and moisture. The aim of this review paper is to find different encapsulation materials and techniques for perovskite and organic solar cells according to the present understanding of reliability issues. It discusses the available encapsulate materials and their utility in limiting chemicals such as water vapour, oxygen penetration. It also covers the mechanisms of mechanical degradation within the individual layers and solar cell as a whole, and possible obstacles to their application in both organic and perovskite solar cells. The contemporary understanding of these degradation mechanisms, their interplay and their initiating factors (both internal and external) are also discussed.

In the field of agricultural food production, the transition between organic and inorganic farming methods has been an issue of much debate. The debate, on one hand, stresses the urgency for the transition in order to preserve environment and health; and, on the other hand, emphasizes the pressure of maintaining food production for a large growing population. Thus, the dilemma is how to find an agricultural system that would balance between obtaining food security and ensuring a safe sustainably environment-friendly food production system. This article focuses on the debate, in the context of Bangladesh, and questions whether it is the proper time, and stage in the development process, to attempt the transition from inorganic conventional food production methods to organic food production methods. This article contemplates why the organic rice market is not expanding in Bangladesh, and attempts to explain the slow growth of the market through the two main factors of income constraint and lack of awareness among people about the environmental and health detriments of inorganic farming methods. The study is exploratory in nature, and finds that it is not mainly the lack of awareness but the income constraint that can be principally attributed to the slow expansion of the organic rice market in Bangladesh. Through exploring consumers’ awareness about organic farming methods and their demand for organic products, this study shows how income as the major constraint, besides price, affects consumers demand for organic and inorganic rice in Bangladesh. Income being identified as the major barrier reveals the potential of the organic rice market to grow in the future, as Bangladesh continues its journey towards becoming a middle-income country.

Traditional high pressure mechanical compressors account for over half of the car station’s cost, have insufficient reliability and are not feasible for a large-scale fuel cell market. An alternative technology, employing a two-stage, hybrid system based on electrochemical and metal hydride compression technologies, represents an excellent alternative to conventional compressors. The high-pressure stage, operating at 100-875 bar, is based on a metal hydride thermal system. A techno-economic analysis of the metal hydride system is presented and discussed. A model of the metal hydride system was developed, integrating a lumped parameter mass and energy balance model with an economic model. A novel metal hydride heat exchanger configuration is also presented, based on mini-channel heat transfer systems, allowing for effective high-pressure compression. Several metal hydrides were analyzed and screened, demonstrating that one selected material, namely (Ti_0.97Zr_0.03)_1.1Cr_1.6Mn_0.4, is likely the best candidate material to be employed for high-pressure compressors under the specific conditions. System efficiency and costs were assessed based on the properties of currently available materials at industrial levels. Results show that the system can reach pressures on the order of 875 bar with thermal power provided at approximately 150 °C. The system cost is comparable with the current mechanical compressors and can be reduced in several ways as discussed in the paper.

This review proposes an overview on the use of organic functionalized carbon nanostructures (CNSs) into solar energy conversion schemes. Our attention has focused in particular on the contribution given by organic chemistry to the development of new hybrid materials that find application in dye sensitized solar cells (DSSC), organic photovoltaics (OPV), perovskite solar cells (PSC) and also in photocatalytic fuel production, focusing in particular on the most recent literature. The request for new materials able to accompany the green energy transition that are abundant, low cost, with low toxicity, from renewable sources has further increased the interest in CNSs that meet all these requirements. The inclusion of an organic molecule, thanks to both covalent and non-covalent interactions, into a CNS, leads to the development of a completely new hybrid material able of combining and improving the properties of both starting materials. Besides the numerical data, which unequivocally state the positive effect of the new hybrid material, we hope that these examples can be inspiring for further research in the field of photoactive materials from an organic point of view.

This study investigates the impact of circular economy (CE) strategies on organizational resilience (OR) within the metal industry, focusing on a case study of a forging department in a large man-ufacturing company. The idea of the paper is to link the macroeconomic topic of circular economy (CE) with microeconomic and practical activities in the organization, exploring how CE principles can improve resource efficiency, sustainability, and organizational resilience. A systematic literature review and case study methodology were used to assess the relationship between CE and OR. The findings reveal that companies with higher circularity demonstrate better resilience, both in normal operations and during crises. Specifically, in the case study, the closure of the forging department, following a detailed analysis using the Inputs-Mediators-Outputs (IMO) model, emerged as the most sustainable option, yielding financial, environmental, and operational benefits. This decision aligned with the company’s long-term goals of energy efficiency and carbon neutrality. The research highlights the significance of integrating CE strategies with business processes to not only achieve sustainability but also to build a more adaptable and resilient organization. Future research should explore broader applications of this framework across different industries to strengthen the links between circular economy practices and organizational resilience.

Biochar is a porous material produced by pyrolisis of biomass and can be modified using metal oxide to improve its adsorption performance, especially toward organics substances. The activated biochar was synthesized from patchouli biomass to study effect of calcination temperature on both structural properties and paracetamol drug adsorption of the composite was studied. Some process routes were conducted, including the patchouli biomass pyrolysis using CoCl2 activator, the activated biochar impregnation using 0.1 M FeCl3 solutions, biochar-FeCl3 calcination at various temperatures (400, 600, 800 oC) in the almost closed porcelain crucible, product characterizations using X-ray diffraction and FTIR spectrometry, and paracetamol adsorption test at various concentrations (10, 20, 30, 40, and 50 ppm). The paracetamol concentrations were analyzed using UV-Vis spectrophotometry at 243 nm. The adsorption data was treated using Langmuir, Freundlich, and Dubinin-Radushkevich (DR) models. The product diffractograms indicated α-Fe2O3, γ-Fe2O3, FeFe2O4 beside the carbon turbostratic structure. The metal oxide peak heights increased by increasing of the temperature. FTIR spectra significantly started to change at 600 oC. Adsorption test of paracetamol gave the highest adsorption capacity of 56.37 mg/g at 800 oC (Langmuir model) with correlation coefficient of 0.964. The highest adsorption energy was achieved at 800 oC, i.e 530.33 J/mol (physical adsorption) with a dimensionless factor, the RL value of 0.86 (favorable adsorption), and the n constant of 1.58 (favorable adsorption).

The properties of coatings obtained using two surface preparation methods were compared: heating and etching by ion bombardment with plasma generation by arc evaporators and heating and etching by a glow discharge. A Ti-TiN-(Ti,Cr,Al)N coating was deposited. The use of a glow discharge provides better resistance of the coating to destruction during the scratch test and wear resistance of metal-cutting tools when turning steel. As the cutting speed increases, the advantage in wear resistance of the coating deposited using a glow discharge increases. During the process of heating and etching by ion bombardment with metal ions, a nanolayer rich in cobalt and tooling elements (iron, molybdenum) is formed in the area of the interface of the coating and the carbide substrate. When heated and etched by a glow discharge, such a layer does not form. When using both methods, there is identical diffusion of tungsten into the coating and diffusion of chromium and possibly titanium into the substrate. Thus, the glow discharge heating and etching method can be effectively used in the process of PVD coating deposition.

One important goal of research on heterogeneous catalysis for Fischer Tropsch synthesis (FTS) is to understand the connection linking catalyst morphology and its activity. Development of these effective catalysts highlights the potential for understanding the effectiveness of promoted supported catalysts and revealing their complex and dynamic effects in FTS. The metal-support interaction (MSI) is influenced by the physicochemical and textural features provided by the modified support and can directly influence the sizes of active metal crystallites, reactants and/or products mass transfer, dispersion, mechanical strength, stability and consequently the adsorption-desorption characteristics of the catalyst. Herein, this article explores the general strategies for modifying silica supports (achieved through doping, coating, or promoting the support or support precursor) and how these strategies can be manipulated to further alter catalyst performance and product selectivity by enhancing the amount of active metal species and improving the intrinsic turnover frequency (TOF). Furthermore, the review emphasises a new strategy (the inverse model of the silica support modification) aiming at overcoming the challenges posed by active metal coating or coverage, as well as pore blockages by promoters that occur during conventional preparation of promoted silica supported FT catalysts.

The band gap research in graphene is still a very important topic for materials application. Here, we report a band gap opening and p-type semiconducting property of the graphene by using an electrochemical doping on graphene surface. The manganese-oxide nanopar-ticles adsorbed on the graphene were used as the dopants in an electrolyte, which induce the band gap opening and the change of electronic structure. In addition, the fabricated graphene FET shows the p-type semiconductor behaviors. The temperature dependent conductivity of the p-type doped graphene at applied potential of 1.5 V during electro-chemical doping shows the formation of band gap of 0.23 eV, which is obtained from the fitting of conductivity equation. The semiconducting properties of manganese-oxide doped graphene is attributed to the formation of manganese-oxide nanoparticle on the surface of graphene.

Heavy metal accumulation in soils used for agricultural purposes is a major issue as it can affect the growth of plants and contain health risks as plants containing heavy metals are taken as food. This study provided the potential of three Bacillus pumilus strains (C-2PMW-8, C-1 SSK-8, and C-1PWK-7) for mitigation of the health factors related to heavy metals on lettuce (Lactuca sativa) grown in chromium contaminated soil from activities related to mining. Lettuce seeds inoculated with B. pumilus strains were grown in pots with garden soil amended with varying amount of chromite mine soil (2.27%, 4.65%, 7.14%). Growth indicators like days to germination, percentage of germination, leaf weight, leaf area and rate of survival decreased with incremental soil chromium levels but improved highly with inoculation of B. pumilus compared to uninoculated controls. When B. pumilus strains were provided, there was also a decreased level in the buildup of chromium in soil as well as lettuce shoots. The results explains that plant growth-promoting B. pumilus strains may be able to lower down the detrimental effects of chromium on lettuce development, hence increment in the effectiveness of phytoremediation.

Hydrogen is considered as an ideal substitute to the traditional fossil fuels because of its widespread sources, high calorific value of combustion, and zero carbon emissions. The electrocatalytic water-splitting to produce hydrogen is also deemed to be the best approach, however, it is a challenge to make high-efficient and low-cost electrocatalysts. Single-atom catalysts (SACs) are considered the most promising candidate to replace the traditional noble-metal catalysts. Compared with SACs, the dual-atom catalysts (DACs) are of greater attraction including higher metal loading, more versatile active sites, and excellent catalytic activity. In the review, several general synthetic strategies and structural characterization methods of DACs are introduced, and the mechanisms of hydrogen evolution reaction (HER) and oxygen evolution reactions (OER) are discussed. The authors hope that the review has given some insights and inspiration to the researchers about DACs in electrocatalytic water-splitting.

This investigation mainly focused on the microstructural analysis of Al based hybrid metal matrix composites. Aluminium as base metal and reinforced with 2% B4 C, ZrO2 (2%,4%,6%), SiC (4%,8%,12%). Specimens were manufactured by using conventional stir casting technique. Hybrid metal matrix composites were examined by using Scanning electron microscope. This research explained XRD, EDS and Fractography analysis. This investigation shows the reinforced material has given better results in all aspects than pure Al6061 alloy and homogeneous dispersion of particles inside the matrix. Porosity, delamination, cracks, particle distributions were observed through microstructural analysis. Additionally determined the crystal size of pure Aluminium 6061 alloy and hybrid composites.

Recent developments in the field of room temperature ferromagnetic metal oxide semiconductors (RTFMOS) have shown promising potential for improved photocatalytic performance. This review focuses on the combined study of photocatalytic and ferromagnetic properties at room temperature, with a particular emphasis on metal oxides, such as TiO2, which have emerged as a key area of interest in the domains of magnetism and environmental remediation. Despite extensive research over the years, the precise mechanism behind the interplay of ferromagnetism and photocatalysis in these materials remains incompletely understood. Several critical factors contributing to magnetism have been hinted at, including oxygen vacancies and various metal doping. Numerous reports have demonstrated that these factors play a primary role in room temperature ferromagnetism and photocatalysis in wide-band-gap metal oxides. However, establishing a direct correlation between magnetism, oxygen vacancies, dopant concentration, and photocatalysis has proven challenging. This review aims to provide a comprehensive overview of the recent progress in understanding the magnetism and photocatalytic behaviour of metal oxides. By examining the latest findings, this study sheds light on the potential of RTFMOS as effective photocatalysts, thereby contributing to advancements in environmental remediation and related applications.

To address the challenges associated with the difficult electromagnetic (EM) scattering computations of anisotropic dielectric-coated metallic composite targets, we proposed an efficient hybrid algorithm for simulating the EM scattering of complex targets with anisotropic dielectric coatings. This method, based on Impedance Boundary Condition (IBC), utilizes surface impedance vectors to describe the EM properties of the dielectric. It fully leverages the respective advantages of the low-frequency Method of Moments (MoM) and the high-frequency Physical Optics (PO) to achieve high-precision and rapid EM simulation of anisotropic dielectric-coated metallic composite targets. Employing boundary conditions and equivalent principles, we equivalently transform the EM scattering problem of targets with thin dielectric coatings into the radiation problem of equivalent EM current on impedance surfaces. This enables the high-precision and rapid calculation of Radar Cross Sections (RCS) for complex targets with anisotropic dielectric coatings. Using examples such as a square plate structure, a simplified aircraft, and a complex satellite model, the simulation results exhibit a high degree of agreement with full-wave numerical solutions and demonstrate a significant advantage in computational resources. This research convincingly demonstrates the accuracy and effectiveness of the proposed method.

We report a simple and high-performance flexible strain sensor based on liquid metal nanoparticles (LMNPs) on polyimide substrate by laser induced deposition. The LMNPs were prepared by ultrasonic method, and then the femtosecond laser direct writing technology was used to induce the assembly and deposition of the LMNPs to form liquid metal microwires. Laser local sintering enhances the connection between particles, and a wearable strain sensor was fabricated with the high sensitivity as high as 76.18, the good linearity (a correlation coefficient of 0.999) in a wide sensing rage, the fast response/recovery time of 159 ms/120 ms. Attributed to these extraordinary strain sensing performances, the sensor can sense various dynamic strains in real time, monitor both subtle physiological activities and large human motions. It can be adhered to human skin, and well reflect the change of facial expression and realize real-time monitoring of facial expression. And the vocal cord vibration can be detected for speech recognition while the sensor attached to the outside of the throat.

Hip replacement has significantly improved the quality of life of patients with symptomatic hip osteoarthritis. Metal-on-metal (MoM) bearings have been used with conventional total hip re-placement (THR) for several decades with promising results from early applications. Wear and corrosion of these implants may lead to a release of metal products into surrounding tissue and body fluids. From the 1980s onwards, the search for increasingly better coupling materials with low levels of wear led to the rise of hard-on-hard couplings such as ceramic-on-ceramic (CoC). The latter is currently the coupling with the longest known duration and with a wear rate close to zero. MoM coupling has been for a long time the most significative alternative, but systemic and local complications linked to the release of chromium and cobalt ions, determine the withdrawn from the market. One other alternative proposed over the time has been Ceramic-on-Metal (CoM) bearing. Preliminary results have been described as favourable, but due to the failures of metal on metal it has been withdrawn from the market, without causing significant clinical complications. In this narrative review, we analysed risks and benefits associated with the implantation of hybrid hard-on-hard bearings, such as CoM.

New complexes of manganese(II) hexafluoroacetylacetonate [Mn(hfac)2] with 2-(1-R-3-pyrazol-4-yl)-4,4,5,5-tetramethyl-2-imidazoline-3-oxide-1-oxyl (R = CHF2, CH2CH2F, CH2CHF2 or CH2CF3) were synthesised and characterised structurally and magnetically. All complexes were prepared under similar conditions. Nonetheless, their crystal structures were considerably different. Depending on the structure of fluorinated alkyl substituent R, the complexation reaction led to complexes of three types: chain-polymeric complexes with the head-to-head or head-to-tail motif and complexes of molecular structure. All complexes show strong antiferromagnetic behaviour in a high-temperature region (150−300 K) and weak ferro- or antiferromagnetic exchange interactions at low temperatures. The stronger antiferromagnetic exchange, –101.7 ± 1.5 or –136 ± 10 cm–1, –82.3 ± 1.3 cm–1 and –87.4 ± 1.3 cm–1, was attributed to the magnetic interaction in three- or two-spin clusters: {&gt;N∸O–Mn2+–O∸N&lt;} or {&gt;N∸O–Mn2+}, respectively. The weaker antiferromagnetic interaction, –0.005, between three-spin clusters or ferromagnetic interactions, 0.18–0.81 cm–1, between two-spin clusters are realised through the pyrazole ring or intermolecular contacts.

The interactions of metal ions with fulvic acids resulted in changes in the particle size and charge. Particle size distribution was trimodal for fulvic acids, bimodal for fulvic complexes with calcium and magnesium, and copper-fulvic complexes had only one size fraction. The compensation of negative charge of carboxylic and phenolic functional groups by positive charged metal ions resulted in the increase in zeta potential which was getting closer to zero in the case of copper-fulvic complexes. However, all metal humic complexes behaved as colloidally unstable which resulted in visually observable sedimentation. Calorimetric measurements provided positive values of changes in enthalpy which indicated endothermic processes. In contrast quantum chemical calculations as well as experiments with model compounds provided negative values indicated exothermic processes. Changes in Gibbs energy were determined as negative and changes in entropy as positive which meant spontaneous processes.

Metal Additive Manufacturing (MAM) has emerged as a promising technology in the aerospace industry, enabling the production of complex components with enhanced design flexibility and reduced lead times. Concurrently, Industry 4.0 has gained significant attention for its potential to revolutionize aerospace manufacturing processes. The paper aims to cluster and review the literature on MAM in the aerospace industry, specifically focusing on its relevance to Industry 4.0 and its applicability throughout the various stages of the product life cycle for the chief purpose of matching supply with demand. Identified gaps and challenges are analyzed, highlighting the need for further research and outlining research agenda aimed at advancing the integration of MAM for Industry 4.0 in the aerospace sector. By addressing these research areas, the aerospace industry can unlock the value of MAM within an Industry 4.0 framework, leading to improved efficiency, productivity, and competitiveness.