Two pre-pulses focused at different positions and at different time moments were used to enhance THz emission generated by the main pulse. The emission of THz radiation from air breakdown regions of focused ultrashort fs-laser pulses (800 nm/35 fs) at shockwave front prepared by pre-pulses was investigated, and a 3D spatio-temporal control was established for the most intense emission. The laser pulse-induced air breakdown forms a ~120 micrometers-long focal volume and generates a shockwave that delivers denser air into the focal region of the main pulse for enhanced generation of THz radiation at 0.1-2.5 THz spectral window. The intensity of pre- and main-pulses was at the tunneling ionisation intensities (1-3)x10¹⁶ W/cm² and corresponded to sub-critical (transparent) plasma in air. Polarisation analysis revealed that the orientation of the air density gradients generated by pre-pulses and their time-space placement defined the ellipticity of the generated THz electrical field. The rotational electric current is the origin of THz radiation. The current is created by non-parallel gradients of electron density and temperature. Scaling dependencies of THz emission control are established.

In this research paper an algorithm for the derivation of methods based on theorems and axioms of fuzzy logic is presented, analyzed and applied. This new proposed procedure generates fuzzy methods and evaluates the value of fuzzy propositions through fuzzy implication. The new implications of the family should satisfy a number of axioms. Also, we denote the conditions in order to satisfy the maximum number of axioms. Moreover, authors state and prove theorems focusing on fuzzy implication, observing the rule: the fuzzy function of fuzzy implication is strong and that lead to fuzzy negation. In addition, the optimal number of repetitions is calculated according to the expected truth value. The formulas produced are verified through the use of temperature and humidity values over a certain period of time and in a certain geographical area in Greece. The basic steps of the methodology are the fuzzification of the data given ​​using four membership degree functions and the application of the membership degrees of temperature and humidity values on a new type of fuzzy implication. Finally, we observed that the isosceles trapezium gave the best results and the type of fuzzy implication can be effectively applied.

This paper presents the results of a comparison of the seasonal dynamics of carbon dioxide content in the atmosphere and the phenological phases of various water bodies located in the boreal and subarctic zones for 2012–2020. Six large freshwater areas were selected as research objects: Lake Baikal, Lake Ladoga, Gulf of Ob, Lake Huron, Great Bear Lake and Great Slave Lake. In addition, four areas of wetlands in Western Siberia were studied. The CO2 concentration in the air column over water bodies was obtained from CAMS global greenhouse gas reanalysis data. These data represent three-dimensional fields of aerosols and chemical components in the atmosphere, with complete coverage of the globe. The phenological phases of the water bodies were determined using data from the MIRAS microwave radiometer of the SMOS satellite. The comparison and analysis performed showed that the concentration of CO2 in the atmosphere over the studied water bodies has a seasonal cyclical nature. The minimum concentration corresponds to the summer period due to strong photosynthesis of phytoplankton and swamp vegetation, which results in the absorption of carbon dioxide. The maximum CO2 concentration over the water bodies corresponds to the end of the winter – the beginning of the spring period, when photosynthesis processes are minimal. During this period, CO2 is being accumulated in water bodies and subsequently emitted. In freezing lakes located in the boreal zone, in addition to a stable spring maximum of CO2, a strong short-term release of carbon dioxide is sometimes observed, also corresponding to the stage of destruction of the ice cover. It is associated with the release of CO2 accumulated over the winter period, which was “sealed” in the ice and in the water column under the ice. The absence of such a release in the waters of the subarctic zone is explained by the lower biological productivity of these reservoirs compared to the waters of the boreal zone.

This article presents an analysis of monthly precipitation totals based on the Global Precipitation Climatology Centre database and monthly mean temperatures based on National Oceanic and Atmospheric Administration data for 377 catchments located around the world. Data sequences covering 110 years from 1901 to 2010 were analysed. The long-term sequences of precipitation and temperature were used to assess the variability of climate extremes, referred to here as polarisation. Measures of polarisation used in the natural sciences are discussed. A simple measure of polarisation was presented and applied to long-term sequences of monthly precipitation totals and monthly mean temperatures. Due to the nature of the proposed polarisation measure, other characteristics of precipitation and temperature sequences are also presented as a background for the discussion of the polarisation index. The study showed the existence of trends related to the polarisation of temperature and precipitation phenomena. As a result of the analysis, trends of polarisation factors in the area of precipitation and temperature were identified in 11 catchments out of the 377 analysed catchments. The trend analysis used Mann-Kendall tests at a level of significance of 5%. The Pettitt test was used to determine the point of trend change for precipitation and temperature data. The whole investigation is supported by rich graphical analyses, and the results are presented in tabular form.

A novel hybrid CSP-PV power plant is presented. Instead of the integration used in current hybrid power plants, where part of the PV production is charged into the thermal energy storage system through electrical resistors, the proposed system integrates both PV and thermal solar fields using a high-temperature heat pump. Both the heat pump and the heat engine are based on Brayton supercritical CO2 thermodynamic cycles. Such integration allows for charging the molten salts storage as if a central tower receiver field supplied the thermal energy, whereas parabolic trough collectors are employed. Unlike conventional hybrid plants, where the storage of PV production leads to a decrease in power injected into the grid throughout the day, the power injected by the proposed system remains constant. The heat engine efficiency is 44.4%, and the COP is 2.32. The LCOE for a 50 MWe plant with up to 12 hours of storage capacity is 171 $/MWh, which is lower than that of existing CSP power plants with comparable performance. Although the cost is higher compared to a PV plant with batteries, this hybrid system offers two significant advantages: it eliminates the consumption of critical raw materials in batteries, and all the electricity produced comes from a synchronous machine.

With simple but rigorous arguments we prove that the ordinary second quantization of bosonic and fermionc fields is formally equivalent to constraining the elementary degrees of freedom of the classical fields to have intrinsically periodic dynamics in time. This result confirms and extends the formal equivalence obtained in previous papers for general Hamiltonian systems in terms of canonical quantization, for elementary relativistic particles also in terms of the Feynman Path Integrals, as well as other remarkable correspondences of both phenomenological and theoretical fundamental interest.

The article presents an analysis of monthly precipitation totals based on the GPCC database, and monthly mean temperatures (NOAA data) for 377 catchments distributed across the globe. The analysis included 110-year data sequences from 1901 to 2010 calculated from grid data with a spatial resolution of 0.5°x 0.5° longitude and latitude. Long-term sequences of precipitation and temperature were used to assess the polarization of climatic phenomena. The noticeable impact of polarization in the area of extreme changes in temperature and precipitation is related to anthropogenic factors such as greenhouse gas emissions, deforestation and pollution, which affect ecosystem functioning, biodiversity, water resources and economies. The paper demonstrates the existence of trends related to the polarization of temperature and precipitation phenomena. The measures of polarization used in science are discussed. A simple measure of polarization was proposed and applied to both long-term sequences of monthly precipitation totals and monthly mean temperature. Due to the nature of the proposed polarization measure, other characteristics of the precipitation and temperature sequences are also presented as background for the discussion of the polarization index. The paper presents, for a selection of several hundred catchments from around the world, analyses of the assessment of precipitation and temperature trends using non-parametric tests. The trend analyses use Mann -Kendall tests at the 5% significance level. A Pettitt test was used to determine the trend change point for precipitation and temperature data. The whole is supported by rich graphical analyses and the results are presented tabularly.

It is not easy to dynamically analyze thermal bridges that require multidimensional analysis in building energy simulations, which are mostly one-dimensional platforms. To solve this problem, many studies have been conducted and, recently, a study was conducted to model the thermal bridge based on the data by approaching this in a similar way to steady-state analysis, showing high accuracy. This was an early-stage study, which is only applicable when the indoor temperature is constant. By extending this study, a thermal bridge model that can be applied even when the indoor temperature changes over time is proposed and validated. Since the governing equation, the heat diffusion equation, is linear, the key idea is to create and apply two thermal bridge transfer function models by expressing the heat flow entering the room as a linear combination of the transfer function for indoor temperature and the transfer function for outdoor temperature. For the proposed thermal bridge model, the NRMSE of the model itself showed a high accuracy of 99.9%, and in the verification through annual simulation using the model, the NRMSE showed an accuracy of 88.8%.

For the first time, few-layer graphene (FLG) nanosheets were synthesized by the method of self-propagating high-temperature synthesis (SHS) from biopolymers (starch and lignin). We suggested that biopolymers (lignin, tree bark) and polysaccharides, in particular starch, could be an acceptable source of native cycles for the SHS process. The carbonization of biopolymers under the conditions of the SHS process was chosen as the basic method of synthesis. Chemical reactions, under the conditions of the SHS process, proceed according to a specific mechanism of nonsothermal branched-chain processes, which are characterized by the joint action of two fundamentally different process-accelerating factors - avalanche reproduction of active intermediate particles and self-heating. The method of obtaining FLG nanosheets included the thermal destruction of hydrocarbons in a mixture with an oxidizing agent. We used biopolymers as hydrocarbons and ammonium nitrate as an oxidizing agent. Thermal destruction was carried out in the mode of SHS, heating the mixture in a vessel at a speed of 20–30 oC/min to 150-200 oC and keeping at this temperature for 15–20 min with the discharge of excess gases into atmosphere. A combination of spectrometric research methods, supplemented by electron microscopy data, has shown that the particles of the carbonated product powder in their morphometric and physical parameters correspond to FLG nanosheets. An X-ray diffraction analysis of the indicated FLG nanosheets was carried out, which showed the absence of formations with a graphite crystal structure in the final material. The surface morphology was also studied and the features of the IR absorption of FLG nanosheets were analyzed. It is shown that the developed SHS method makes it possible to obtain FLG nanosheets with linear dimensions of tens of microns and a thickness of not more than 1-5 graphene layers (several graphene layers).

Climate change is expected to increase the frequency and severity of abiotic stresses that lead to loss of crop yield. We investigated the effect of salinity (S), short episodes of high temperature (HS) and combination of S+HS at the reproductive phase on dead pericarps properties and yield of the crop plant Brassica juncea. Three intervals of HS resulted in massive seed abortion; seeds from salt-treated plants germinated poorly. Pericarp extracts of salt-treated plants reduced seed germination of B. juncea; all pericarp extracts completely inhibited seed germination of tomato and Arabidopsis; removal of pericarp extracts restored seed germination. HS reduced all metabolites accumulated in dead pericarps, except for upregulation of isomaltose and cellobiose. Salt induced alteration in metabolite levels including increase in proline, reduction in TCA intermediates and changes in phytohormone levels. Proteome analysis revealed hundreds of proteins stored in dead pericarps whose levels and composition were altered under salt stress. The integration of metabolic and proteomic data showed that changes in metabolites were highly correlated with changes in proteins involved in their biosynthetic pathways. Thus, besides providing a physical shield for seed/embryo protection dead pericarps store beneficial substances whose levels, composition and biological function are altered under stress, further highlighting the elaborated function of dead organs enclosing embryos in seed biology and ecology. The detrimental effect of HS on crop production might have implications for global food security in the face of climate change.

Laser powder bed fusion (LPBF) is an additive manufacturing process employed in many industries, for example for aerospace, automotive and medical applications. In these sectors, mainly nickel-, aluminum- and titanium-based alloys are used. In contrast, the mechanical engineering industry is interested in more wear-resistant steel alloys with higher hardness, both of which can be achieved with a higher carbon content, like in high-speed steels. Since these steels are susceptible to cracking, preheating needs to be applied during processing by LPBF. In a previous study, we applied a base plate preheating temperature of 500 °C for HS6-5-3-8 with 1.3 % carbon content. We were able to manufacture dense (p > 99.9 %) and crack-free parts from HS6-5-3-8 with a hardness > 62 HRC (as built) by LPBF. In this study, we investigate the influence of preheating temperatures up to 600 °C on hardness and microstructure dependent on part height for HS6-5-3-8. The microstructure was studied by light optical microscopy (LOM), scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD). The analysis of hardness and microstructure at different part heights is necessary because state-of-the-art preheating systems induce heat only into the base plate. Consequently, parts are subjected to temperature gradients and different heat treatment effects depending on part height during the LPBF process.

In this work we have critically reviewed the processes in high-temperature sublimation growth of graphene in Ar atmosphere using enclosed graphite crucible. Special focus is put on buffer layer formation and free charge carrier properties of monolayer graphene and quasi-freestanding monolayer garphene on 4H-SiC. We show that by introducing Ar at different temperatures, TAr one can shift to higher temperatures the formation of the buffer layer for both n-type and semi-insulating substrates. A scenario explaining the observed suppresed formation of buffer layer at higher TAr is proposed and discussed. Increased TAr is also shown to reduce the sp3 hybridization content and defect densities in the buffer layer on n-type conductive substrates. Growth on semi-insulating substrates results in ordered buffer layer with significantly improved structural properties, for which TAr plays only a minor role. The free charge density and mobility parameters of monolayer graphene and quasi-freestanding monolayer graphene with different TAr and different environmental treatment conditions are determined by contactless terahertz optical Hall effect. An efficient annealing of donors on and near the SiC surface takes place in intrinsic monolayer graphene grown at 2000∘C, and which is found to be independent of TAr. Higher TAr leads to higher free charge carrier mobility parameters in both intrinsically n-type and ambient p-type doped monolayer graphene. TAr is also found to have a profound effect on the free hole parameters of quasi-freestanding monolayer graphene. These findings are discussed in view of interface and buffer layer properties in order to construct a comprehensive picture of high-temperature sublimation growth and provide guidance for growth parameters optimization depending on the targeted graphene application.

Land Surface Temperature (LST) and Land Use Land Cover (LULC) are the principal aspects of climate and environment studies. The object of the study is to assess spatial relationship between LST and remote sensing LULC indices at the global and continental scale. Moderate Resolution Imaging Spectroradiometer (MODIS) Aqua daytime LST and eight LULC MODIS indices of 2018 prepared and processed using Earth Engine Code Editor. R squared and significance of the relationship values of randomly selected points computed in R program. The research observed the relationship between examined indices and LST is significant at the 0.001 level. Normalized Difference Water Index (NDWI) and Normalized Difference Snow Index (DSI) are the dominant drivers of LST in the world, Asia and North America. In Australia and Africa, Normalized Difference Vegetation Index (NDVI) and Enhanced Vegetation Index (EVI) are the dominant drivers of LST. Albedo and Normalized Difference Soil Index (NDSI) have superior in Central America. In South America and Europe, the dominant driver of LST is NDWI. Relationship between albedo and LST is moderate inverse on a global scale. Observed relationship between LST and examined vegetation indices is positive in Europe and North America while inverse in Australia and Africa. All observed relationship between Normalized Difference Built-up Index (NDBI) and LST are positive. Association observed between NDSI and LST is positive in Australia, Africa and Central America.

A ducted photovoltaic façade (DPV) unit Studied using experimental Prototype and simulated in a full scale Computational Fluid Dynamics CFD Model. The Study comes in two parts; This is Part I with the title detailed above and Part II titled ‘A Ducted Photovoltaic Façade Unit with Buoyancy Cooling: Part II CFD Simulation’.. The process adopted in the experimental study is replicated in the simulation Part. The aim was to optimize the duct width behind the solar cells to allow for maximum buoyancy-driven cooling for the cells during operation. Duct widths from 5 to 50 cm were tested in a Proto-type. A duct width of 45 cm had the maximum calculated heat removed from the duct; however, the lowest cell-operating temperature was reported for duct width of 50 cm. It was found that the DT between ducts' inlets and outlets range from 5.47 °C to 12.32 °C for duct widths of 5–50 cm, respectively. The ducted system enhanced module efficiency by 12.69% by reducing PV temperature by 27 °C from 100°C to 73 °C. The maximum calculated heat recovered from the ducted PV system is 422 W. This is 47.98% from the incident radiation in the test. Total summation of heat recovered and power enhanced by the ducted system is 61.67%.

Direct laser writing three-dimensional nano-lithography is an established technique for manufacturing functional 3D micro- and nano-objects via non-linear absorption induced polymerization process. In this Chapter an underlying physical mechanisms taking place during nano-confined polymerization reaction, induced by tightly focused ultra-short laser pulses, are reviewed and discussed. The special attention is paid on the effects that directly impact structuring resolution and minimum achievable feature size. Analysis of possible photo-initiation mechanisms as contributing multi-photon absorption and avalanche ionization in pre-polymers under diverse exposure conditions (wavelength, pulse duration) is presented. Feasible structuring of pure (non-photosensitized) and functional nanoparticles doped polymer precursors is justified and benefits of such materials/structures for microoptics, photonics and cell scaffolds are highlighted. The influence of temperature effects (induced by writing process itself or determined by ambient conditions) on polymerization process, observed in different pre-polymers under diverse exposure regimes is outlined. The further adjustment of the structuring resolution is possible via precise control of light polarization and diffusion assisted radical quenching. The work is concluded with a brief outlook on future challenges and perspectives related to refinement of 3D ultra-fast laser lithography fabrication process in the means of application of diverse post-processing methods and research into novel photo-curable materials including inorganic ones.

External quantum efficiency of industrial-grade green InGaN light-emitting diodes (LEDs) has been measured in a wide range of operating currents at various temperatures from 13 K to 300 K. Unlike blue LEDs, the efficiency as a function of current is found to have a multi-peak character, which could not be fitted by a simple ABC-model. This observation correlated with splitting of LED emission spectra into two peaks at certain currents. The characterization data are interpreted in terms of non-uniformity of the LED active region, which is tentatively attributed to extended defects like V-pits. We suggest a new approach to evaluation of temperature-dependent light extraction and internal quantum efficiencies taking into account the active region non-uniformity. As a result, the temperature dependence of light extraction and internal quantum efficiencies have been evaluated in the temperature range mentioned above and compared with those of blue LEDs.

Simulations of the pump response time refer to the determination of the time constant of the transient process when the flow and pressure change. The changes mentioned in the standards are precisely defined and prescribed by the "MIL-P-19692E" norms. The simulation showed that the time constants are within the permissible limits prescribed by these norms. The diagram shows the responses for the considered pump and for the case when the flow changes from Qn to Qmin and changes from Qmin to Qn. The time constants t1 and t2 are defined on the diagrams, with the parameters that the pump has. In addition, the standards define the pressure jump that occurs during the transient process as well as time constants. From the flow change diagram, it can be seen that the flow change is also very fast and takes place in time intervals shorter than 0.1 s. By evaluating the size of the time constants, t1 and t2, it can be concluded that they have a value below 0.05 s, which meets the regulations in that area. Also, the size of the jump pressure meets the regulations because it is only 1.2 M Pa above the nominal pressure.

By using the method of high-temperature solid-phase reaction, the new piezoceramic SrBi2Nb2-2xWxSnxO9 was obtained, in which partial substitution of niobium (Nb) atoms with Sn4+ and W6+ atoms in the compound SrBi2Nb2O9 took place in the octahedra of the perovskite layer (B-position). X-ray diffraction studies have shown that these compounds are single-phase SrBi2Nb2-2xWxSnxO9 (x = 0.1, 0.2) and two-phase SrBi2Nb2-2xWxSnxO9 (x = 0.3, 0.4), but they all had the structure of Aurivillius – Smolensky phases (ASPs) with similar parameters of orthorhombic elementary cells, corresponding to the spatial group A21am. The dependences on temperature of the relative permittivity ε/ε0 and the tangent of the loss angle tan d at different frequencies were measured.

The application of distributed fiber optic strain and temperature measurement can be utilized to address a multitude of measurement tasks across a diverse range of fields, particularly in the context of structural health monitoring in the domains of building construction, civil engineering, and special foundation engineering. However, a comprehensive understanding of the influences on the measurement method and the sensors is essential to prevent misinterpretations or measurement deviations. In this context, this study investigated the effects of moisture exposure, including various salt solutions and a high pH value, on a distributed strain measurement using Rayleigh backscattering. Three fiber optic sensors with different coating materials and one uncoated fiber were exposed to five different solutions for 24 hours. The study revealed significant discrepancies in deformation between the three coating types depending on the surrounding solution. Furthermore, in contrast to the prevailing literature, which predominantly describes swelling effects, a negative deformation was observed in a magnesium chloride solution. The findings of this study indicate that corresponding effects can impact the precision of measurement, potentially leading to misinterpretations. Conversely, these effects could be used to conduct large-scale monitoring of chemical components using distributed fiber optic sensing.

A new clothing resistance model is described and applied to characterize the human thermal and moisture climates. The climate was described by the thermal (rcl,t) and evap-orative (rcl,e) resistances of comfortable, imaginary clothing. The key input variable of the model is the rate of sweating (λEsw). Since sweating is an individual-specific process, the model applies to the individual. The observations were carried out by a single individual in Martonvásár (Hungarian lowland, Central Europe) in the summer of 2023 and the winter of 2024. During the observations, the observer walked at a speed of 1.1-1.7 ms-1 in weather-appropriate clothing. Among the results, we would highlight the following: Dur-ing large environmental heat surpluses, the rcl,t values were found to be between 0.1-0.5 clo-t (clo-t = 0.155 m2·℃·W-1), while the rcl,e values fell between 0.4-0.8 clo-e (clo-e = 0.155 m2·hPa·W-1). The values of the parameters close to 0 were caused by intense sweating (λEsw > 200 Wm-2). The applicability of the model is limited and largely depends on the rela-tionship between λEsw and the metabolic heat flux density.

The predatory mirids Macrolophus pygmaeus Ramber and Nesidiocoris tenuis Reuter (Heteroptera: Miridae) are used for the biological control of Tuta absoluta Meyrick (Lep.: Gelechiidae) and other pests in tomato greenhouses. The functional response of 1 (young) and 10 (old) days old adult females and males of M. pygmaeus and N. tenuis on eggs of T. absoluta, was determined on tomato at two temperatures (20° and 25°C) and LD 16:8 and found to be Type II. M. pygmaeus females exhibited higher predation efficiency, than males at both tested temperatures. Young M. pygmaeus females had a higher efficiency than old ones, whereas males had a low efficiency irrespective of age. The predation efficiency of N. tenuis was high (but lower than M. pygmaeus) in both young females and males, although old females had a higher efficiency than the respective males. Our results show that the two predatory species have different functional response characteristics to their prey depending mainly on sex and age which may affect their role as biological control agents.

Abstract Octreotide is the first synthetic peptide hormone, consisted of eight amino acids, that mimics the activity of somatostatin, a natural hormone in the body. During the past decades, advanced instrumentation and crystallographic software established X-ray Powder Diffraction (XRPD) as a valuable tool for extracting structural information of biological macromolecules. The latter was demonstrated by the successful structural determination of octreotide at a remarkably high d-spacing resolution (1.87 Å) (PDB code: 6vc1). This study focuses on the response of octreotide to different humidity levels and temperatures, with a particular focus on the stability of the polycrystalline sample. XRPD measurements were accomplished employing an Anton Paar MHC-trans humidity-temperature chamber installed within a laboratory X’Pert Pro diffractometer (Malvern Panalytical). The chamber is employed to control and maintain precise humidity and temperature levels of samples during XRPD data collection. Pawley analysis of the collected data sets revealed that the octreotide polycrystalline sample is remarkably stable and no structural transitions were observed. The compound retains its orthorhombic symmetry (space group: P212121, a = 18.57744(4) Å, b = 30.17338(6) Å, c = 39.70590(9) Å, d~ 2.35 Å). However, a characteristic structural evolution in terms of lattice parameters and volume of the unit-cell is reported mainly upon controlled relative humidity variation. In addition, an improvement of signal-to-noise ratio in the XRPD data under a cycle of dehydration/rehydration is reported. These results underline the importance of considering the impact of environmental factors, as humidity and temperature, in the context of structure-based drug design, thereby contributing to the development of more effective and stable pharmaceutical products.

: Low-temperature growth of diamond films by chemical vapor deposition (CVD) method is not so widely reported and especially its initial periods of nucleation and growth phenomenon are of particular interest to the researchers. Four sets of substrates were selected for growing diamond films by linear antenna microwave plasma enhanced CVD (LA-MPCVD). Among them, silicon and sapphire substrates were pre-treated with detonation nanodiamond (DND) seeds before diamond growth for enhancement of its nucleation. On the other hand, carbon nanotube (CNT) films on Si substrates were also used as another template for LA-MPCVD diamond growth. In order to enhance the diamond nucleation during CVD growth, some of the CNT films were again pre-treated by electrophoretic deposition (EPD) of diamond nanoparticles. All these substrates were then put inside the LA-MPCVD chamber for growing diamond films under variable processing conditions. Microwave input powers (1100 – 2800 W), input power modes (pulse or continuous), antenna to stage distances (5 - 6.5 cm), process gas recipes (with or without CO2), methane gas percentages (3 - 5%), deposition times (11 – 120 minutes) were altered to investigate their effect on the growth of diamond film on the pre-treated substrates. The substrate temperatures were found to vary from as low as 170oC to a maximum of 307oC during the alteration of the different processing parameters. Contrary to the conventional MPCVD, it was observed that during the first hour of LA-MPCVD diamond growth, DND seeds or the nucleating structures, do not coalesce together to make a continuous film. Deposition time was the most critical factor in fully covering the substrate surfaces with diamond film, since the substrate temperature could not become stable during the first hour of LA-MPCVD. CNT was found to be oxidised rapidly under LA-MPCVD plasma conditions; therefore, a CO2-free process gas recipe was used to reduce CNT burning. Moreover, EPD-coated CNT was found to be less oxidised by the LACVD plasma during diamond growth.

Human-caused anthropogenic greenhouse emissions impact climate globally. In this pilot study, we aim to reveal the impact of oil and gas emissions from local oil deposits in the regime of their natural degradation and development and eco-physiological changes of pine forests in Tatarstan Republic, Russia over the past century. We performed stable carbon isotope analysis in pine tree rings (13Cptrw) to reveal the impact of oil and gas emissions from the giant oil field reservoirs located in Leninogorsk region (UVRT) and the natural reserve site in Raifa. Our results show decreasing 13Cptrw at UVRT in 1943 when oil extraction was started, and in 1970, when it reached the maximum production. We found that 13Cptrw from UVRT indicates on developing unfavourable drier conditions and suppressed tree growth caused by both human-induced oil and deposit infrastructure and natural processes compared to undisturbed Raifa. The 13Cptrw from Raifa is more negative compared to UVRT, which can be explained by higher forest sensitivity to human-induced impact. From an ecophysiological point of view decreasing intercellular to ambient CO2 concentration at the leaf level and increasing intrinsic water use efficiency along with decreasing tree-ring width at UVRT (1970-2021) indicate on development of drought conditions.

Climate change-induced temperature fluctuations pose a significant threat to crop production, particularly in the Southern Hemisphere. This study investigates the transcriptome and physiological responses of rapeseed to post-flowering temperature increases, providing valuable insights into the molecular mechanisms underlying rapeseed tolerance to heat stress. Two rapeseed genotypes, Lumen and Solar, were assessed under control and heat stress conditions in field experiments conducted in Valdivia, Chile. Results showed that seed yield and seed number were negatively affected by heat stress, with genotype-specific responses. Lumen exhibited a 9.3% average seed yield reduction, while Solar showed a 28.7% reduction. RNA-seq analysis of siliques and seeds revealed tissue-specific responses to heat stress, with siliques being more sensitive to temperature stress. Hierarchical clustering analysis identified distinct gene clusters reflecting different aspects of heat stress adaptation in siliques, with a role for protein folding in maintaining silique development and seed quality under high temperature conditions. In seeds, three distinct patterns of heat-responsive gene expression were observed, with genes involved in protein folding and response to heat showing genotype-specific expression. Gene coexpression network analysis revealed major modules for rapeseed yield and quality, as well as the trade-off between seed number and seed weight. Overall, this study contributes to understanding the molecular mechanisms underlying rapeseed tolerance to heat stress and can inform crop improvement strategies targeting yield optimization under changing environmental conditions.

Using an original method for measuring weak radiothermal electromagnetic signals, experimental data were obtained on the analysis of dispersions of noise attractors of the radiobrightness temperature of aqueous solutions of NaCl, Al (NO₃)₃ at dilutions C1 (1:100) – C12 (12:100). The values of dispersions of noise attractors significantly differ from those for the control experiment with water. On the basis of the changed values of the noise attractors of the radiobrightness temperature, the values of the absorption coefficients of the solutions are calculated. The difference between the values of the solutions absorption coefficients and those for water is shown with a successive increase in their values with an increase in the degree of dilution. The difference between the values of the absorption coefficients of solutions of high dilutions and those for water is interpreted as a mechanism of cooperative interaction of ions with water molecules located outside the first hydration shell. A network of water molecules perturbed by ions contributes to the dielectric permittivity was obtained due to new properties at supramolecular interactions on the basis of dispersion interaction.

A quantitative method is proposed to determine of Stone-Wales defects for carbon nanostructures with sp2 hybridization of carbon atoms. The technique is based on the diene synthesis reaction (Diels-Alder reaction). The proposed method was used to determine Stone-Wales defects in the few-layer graphene (FLG) nanostructures synthesized by the self-propagating high-temperature synthesis (SHS) process, in reduced graphene oxide (rGO) synthesized based on the method of Hammers and in the single-walled carbon nanotubes (SWCNT) TUBAL trademark, Russia. Our research has shown that the structure of FLG is free of Stone-Wales defects, while the surface concentration of Stone-Wales defects in TUBAL carbon nanotubes is 1.1×10-5 mol/m2 and 3.6×10-5 mol/m2 for rGO.

To understand lung damage caused by COVID-19, we deduced two-phase lung damage mechanisms. After the lungs are infected with SARS-CoV-2 virus, the affected lung tissue swells and surface properties of pulmonary capillaries change, resulting in an increased flow resistance of affected capillaries. If a sufficient number of capillaries are affected by the infection, the swelling and increased cell wall adhesion collectively raise pulmonary vascular resistance. The increased vascular resistance further increases the dwell times of WBCs in affected capillaries and nearly capillaries. When pulmonary pressure is sufficiently higher, WBCs are forced to squeeze into interstitial spaces or alveolar spaces when local pressures are higher than what the capillaries can withstand. When more and more WBCs are dynamically retained, the flow resistance of more capillaries rises, pulmonary vascular resistance rises, and pulmonary pressure rises. The rise in the pulmonary pressure in turn results in elevated capillary pressures. When capillary pressures around the alveoli are sufficiently high, they cause interstitial pressures to change from normally negative values to positive values. The positive pressures cause fluid leakage to the alveolar space and thus degrade lung function. Tissue swelling, and occupation of WBCs in interstitial spaces and alveolar spaces further reduce compressible volume, and thus cause further rise in the pulmonary vascular resistance and pulmonary pressure. When the pulmonary pressure has reached a critical point as in the second phase, the blood breaks capillary walls and squeezes through interstitial spaces to reach alveolar spaces, resulting in irreversible lung damages. The available free volume in the thorax cage, organ usable capacities, temperature and humid are expected to have great impacts on degree of lung damages. The free volume in the thorax cage, lung usable surplus capacity, and other organ usable capacities determine the arrival time of last-phase irreversible damage. The mechanisms imply that the top priority for protecting lungs is maintaining pulmonary micro-circulation and preserving organ functions in the entire disease course while controlling viral reproduction should be stressed in the earliest time possible. The mechanisms also explain leukecytes are recruited and migrated into inflamed tissues by increasing their dwell times caused by increased local flow resistance.

Thunderstorm electrification has been studied for hundreds of years. Several mechanisms have been proposed to elucidate the electrification, including convective charging, inductive precipitation charging, and ice crystal-graupel collision charging. Field observations and model studies have demonstrated the vital roles that graupel and ice crystals play in the electrification, but the mechanism of the collision charging is still unclear. The fundamental essence of relative growth rate theory used for explaining the tripole charge structure in thunderclouds also needs a further exploration. We analyze the processes of ice crystal-graupel collision charging from charge migration inside hydrometeors to charge separation between two hydrometeors. The driving effects of temperature gradient and chemical potential gradient in charge migration are clarified, as well as the applicability of the relative growth rate theory, thermoelectric effect and surface tension gradient in different humidities. Based on the understanding from these electrification mechanisms, we propose that the essence of charge separation is driven by non-thermal equilibrium, and future studies on thunderstorm electrification should focus on the dynamical non-thermal equilibrium of cloud particles.

A metastable β-Ti alloy, Ti–10V–3Fe–3Al (wt.%), was subjected to thermos-mechanical processing including the compression test at 725°C, which is below the β transus temperature (780°C), and at strain rate of 10-3s-1. The presence of phases was determined using transmission electron microscopy and X-ray diffraction. Although the dynamic recovery took place together with slip, both deformation-induced α˝ martensite and ω were detected as other operating mechanisms for the first time in metastable-β Ti alloys deformed in α+β region. The volume fraction of stress-induced α˝ was higher than that of the same alloy deformed at room temperature due to higher strain applied. Stress-induced twinning was not operational, which could be related to the priority of slip mechanism at high temperature resulted from thermally-assisted nucleation and lateral migration of kink-pairs.

An energy production system consisting solar collector, biogas dry reforming reactor and solid oxide fuel cell (SOFC) was assumed to be installed in Kolkata, India. This study aims to understand the impact of climate condition on the performance of solar collectors with different lengths of parabolic trough solar collector (dx) and mass flow rate of heat transfer fluid (m). In addition, this study has evaluated the amount of H2 produced by biogas dry reforming (GH2), the amount of power generated by SOFC (PSOFC) and the maximum possible households (N) whose electricity demand could be met by the energy system proposed, considering the performance of solar collector with the different dx and m. As a result, the optimum dx was found to be 4 m. This study revealed that temperature of heat transfer fluid (Tfb) decreased with the increase in m. Tfb in March, April and May was higher than that in other months, while Tfb from June to December was the lowest. GH2, PSOFC and N in March, April and May were higher than that in other months irrespective of m. The optimum m was 0.030 kg/s.

This study investigates the properties of solution processed hybrid pol-yimide, PI nanocomposites containing a variety of nanofillers, including polyaniline copolymer modified clay, PNEA, nanographene sheets, NGS, and carbon nanotube sheet, CNT-PVDF, respectively. Through a series of experiments, the flow behavior of poly(amic acid), PAA solution and PAA suspension containing polyaniline copolymer modified clay, PNEA was determined as a function of the shear rate, processing temperature and polymerization time. It is shown that the neat PAA solution exhibited a complex rheological behavior ranging from shear thickening to New-tonian behavior with increasing shear rate and testing temperature. The presence of modified clay in PAA solution significantly reduced the viscosity of PAA. Differential Scanning Calorimetry (DSC) analysis show that polyimide-nanographene sheets, PI NGS nanocomposites processed at high spindle speed (100 rpm) had lower total heat of decomposition which is indicative of improved fire retardancy. The effect of processing temperature on the specific capacitance of polyimide-CNT-PVDF composites containing electrodeposited polypyrrole fillers was determined by using cyclic voltammetry, CV. It was shown that the hybrid composite working electrode material processed at 90˚C produced a remarkably higher overall stored charge when compared to the composite electrode material processed at 250˚C. Consequently, the specific capacitance ob-tained at a scan rate of 5 mV/s for the hybrid nanocomposite processed at 90°C was about 858 F/g after 1 cycle, which is about 6.3 times higher than the specific capacitance of 136 F/g produced by the hybrid nanocomposite processed at 250°C. These findings show that the properties of the hybrid nanocomposites are remarkably influenced by the processing conditions and highlights the need for process optimization.

The North American Monsoon (NAM) in southern Arizona continues to be a topic of interest to ecologists, climatologists, and citizens as well as the triggers and characteristics of plant growth and reproduction in relation to the onset of the monsoon. In researching the onset of the North American Monsoon (NAM) in south-central Arizona relative to the phenology of Saguaro cactus (Carnegiea gigantea) and other Sonoran Desert species we identified interesting and previously unreported features in the NAM rainfall data. We present preliminary descriptive analyses of (1) monsoon onset as measured by the first day after June 1 with precipitation ≥10 mm (1990-2022), (2) first day of year warming of Sea Surface temperatures (SST) in the Gulf of California to ≥29º C measured across five open-sea blocks (mean 9452 km2), and (3) El Niño Southern Oscillation (ENSO) anomaly with a threshold of +/- 0.5º C for the Oceanic Niño Index (ONI) in the Niño 3.4 region (5ºN-5ºS, 120º-170ºW). Three patterns emerge from our analyses: (1) The day of the year of monsoon onset occurs approximately 12 days earlier in the year from 1990-2022 in south-central Arizona. (2) There appears to be a signal in the rainfall onset data very roughly approximating cycles of ENSO Oceanic Niño Index (ONI) anomalies in Niño region 3.4. (3) Gulf of California sea surface temperature (SST) and monsoon onset data support an expected link between the timing of SST warming and monsoon rainfall onset.

A review is here provided about the thermal effects on the optical chirality. To this goal, chiral objects dispersed in an embedding fluid are examined for their magnetoelectric coupling. Thermal effects on several chiral meta-atoms and their ensembles are examined. To this goal, DNA-like helical structures are examined in detail. Mechanical aspect of thermo-elasticity is reviewed along with transverse deformations, while drawing analogies from condensed-matter physics. In this respect, chirality-induced spin selection is reviewed along with the temperature-mediated elec-tron-phonon interactions. A wide range of materials such as polymers and biological cells are also examined for temperature effects. A transition temperature delineating a sign flip in the chirality parameter is identified as well. Chirality-associated functionalities such as ratchet motions, switching, and modulations are investigated for their respective thermal effects. Issues of fabri-cating chiral meta-atoms are also discussed.

Petrochemical plants use on-stream inspection more often to detect and monitor the corrosion on the equipment and piping system. Compared to ultrasonic thickness gauging and pulse-echo A-scan, phased array corrosion mapping has better coverability and can scan a large area to detect general and localized corrosion. This paper's objective is to obtain documentary evidence on the accuracy of corrosion detection from 30°C to 250°C on A36 low-carbon steel by carrying out simulation experiments every 10°C steps. A minimum of three sets of phased array corrosion mapping data in each temperature were collected to study and evaluate the detectability. The data evidence could enhance the confidence level of the plant's end users to use the phased array mapping in the future during an inspection. The experiments were found to be insufficiently thorough despite addressing the initial concerns, leaving more area for discussion in further studies, such as expanding the investigation to thicker carbon steel, stainless steel, and wedge materials.

The broad acceptance of electromobility depends heavily on the performance and service life of the battery technology used. Lithium-ion battery technology is currently the most promising energy storage technology for mobile applications, but the performance and capacity of the cells is extremely temperature sensitive. Especially in these new complex and powerful applications there is a significant need for thermal management. Depending on the ambient conditions, part of the effective battery energy must therefore be used to temper the system. So far, mainly active components have been used for this task. This not only reduces the overall efficiency, but also increases the weight, volume and maintenance requirements of the system. In the present work, an alternative battery temperature management system (BTMS) was developed. A concept based on latent heat storage materials was created, which uses the advantages of thermal energy storage and the design freedom of additive manufacturing technology, and its suitability for use in battery applications was checked. On the one hand, the use of systems for storing thermal energy was researched and, on the other hand, an innovative cooling concept was created considering new production possibilities.

The relocation of the Indonesian capital from Jakarta to Ibu Kota Nusantara (IKN) East Kalimantan IKN will affect several sectors. The change in land use from vegetated to developed land will lead to local climate changes, including the emergence of the urban heat island (UHI) phenomenon, which is reflected in a higher land surface temperature (LST) than the surrounding area. In this study, an analysis of UHI propagation was conducted on a seasonal (DJF, MAM, JJA, and SON), with 5 yearly periods from 2001 to 2020, study area in IKN and its buffer cities (Balikpapan, Samarinda, and Bontang). Terra-MODIS satellite data are processed using Google Earth Engine (GEE) platform and output is done using GrADS. UHI (high LST) is found in urban areas/buffer cities both spatially and temporally in every season, while UHI has not yet occurred in IKN (low LST) and suburban, rural, hilly areas, vegetated areas, and water bodies (lakes, rivers). The cross-sectional latitudinal and longitudinal analysis showed that the LST DJF2015-2020 from highest to lowest temperature are in Balikpapan City (36.84 OC), Samarinda City (36.13 OC), Bontang City (32.3 OC); and IKN zero point (28.82 OC). The UHI propagation was observed in 2001-2005, 2006-2010, 2011-2015, and most during 2016-2020. Seasonally, the UHI was most pronounced in the SON season, while on lowest UHI was observed in the MAM season.

Seed germination and seedling growth represent two vulnerable stages in a plant life cycle and it is important to determine how they will be affected by environmental changes associated with climate change. This study examines the impact of salinity levels (0, 50, 100, and 150 mM) at each of three temperatures (15, 25, and 35˚C) on seed germination and radicle growth for three dormant and three non-dormant varieties of conventional, glyphosate resistant, or reduced lignin alfalfa. The genetic basis and phenotypic plasticity for seed germination and seedling growth in response to salinity and temperature were determined. Both traits were phenotypically plastic with respect to temperature and salinity. Seed germination was 87.0% ± 1.7 at 25˚C, 0mM (no salinity), but decreased to 33.9% ± 3.9 germination at 35˚C and 150mM. Radicle length went from 36.7 ± 1.5 mm after four days at 25˚C, 0mM, to 10.5 ± 0.7 mm at 35˚C, 150mM. The phenotypic response brought seed germination and radicle length away from their optimum, but we detected standing genetic variation for both seed germination and radicle length. Selection to increase both traits at high temperature and salinity would facilitate alfalfa establishment under climate change.

A review is here provided on the thermal effects on the optical chirality. To this goal, chiral objects dispersed in an embedding fluid are examined for their magnetoelectric coupling. Archetypal twisted-Omega particles are examined with respect to electron transport, phonon dynamics, and temperature effects. Continuum-mechanical aspect of thermo-elasticity is reviewed along with transverse deformations. A transition temperature delineating a sign flip in the chirality parameter is identified as well.

We present the results on photothermal (PT) and heat conductive properties of nanogranular silicon (Si) films synthesized by evaporation of colloidal droplets (drop-casting) of 100 ± 50 nm sized crystalline Si nanoparticles (NP) deposited on glass substrates. Finite difference time domain (FDTD) and finite element mesh (FEM) modeling of absorbed light intensity and photo-induced spatial temperature distribution across the Si NP films were well correlated with the local temperatures measured by micro-Raman spectroscopy and used for determination of heat conductivities in the films of various thicknesses. Cubic-to-hexagonal phase transition in these films caused by laser heating was found to be heavily influenced by the film thickness and heat conductive properties of glass substrate, on which the films were deposited. Heat conductivities across the drop-casted Si nanogranular films were found to be in the range of lowest heat conductivities of other types of nanostructurely voided Si films due to enhanced phonon scattering across inherently voided topology, weak NP-NP and NP-substrate interface bonding within nanogranular Si films.

Transverse momentum spectra of +, p, Λ, Ξ or ¯Ξ+, Ω or ¯Ω+ and deuteron (d) in different centrality intervals in Gold-Gold (Au-Au) and Lead-Lead (Pb-Pb) collisions at 62.4 GeV and 2.76 TeV respectively, are analyzed by the blast wave model with Boltzmann Gibbs statistics. We extracted Kinetic freeze out temperature,transverse flow velocity and kinetic freezeout volume from the transverse momentum spectra of the particles. It is observed that the non-strange and strange (multi-strange) particles freezeout separately due to different reaction cross-sections. While the freezeout volume and transverse flow velocity are mass dependent which decrease with the rest mass of the particles. The present work reveals the scenario of double kinetic freezeout in collisions at STAR and ALICE Collaborations. Furthermore, the kinetic freezeout temperature and freezeout volume are larger in central collisions than the peripheral collisions and they decrease from central to periphery. However the transverse flow velocity remains almost unchanged from central to peripheral collisions.

Temperature differences between the atmosphere and river water allow rivers to be used as a hydrothermal energy source. The river-water heat pump system is a relatively non-invasive renewable energy source; however, effluent discharged from the heat pump can cause downstream temperature changes which may impact sensitive fluvial ecosystems. In this study, the water temperature recovery distance of the effluent was estimated for a river section in the Han River Basin, Korea, using the heat transfer equation and the Environmental Fluid Dynamic Code (EFDC) model. Results showed that, compared to the EFDC model, the heat transfer equation tended to overestimate the water temperature recovery distance due to its simplified assumptions. The water temperature recovery distance could also be used as an objective indicator to decide the reuse of downstream river water. Furthermore, as the river system was found to support an endangered fish species that is sensitive to water environment changes, care should be taken to exclude the habitats of protected species affected by water temperatures within water temperature recovery distance.

Abstract: Mass spectrometry research laboratories reported multiple probes for ambient ionization in the last years. Combining them with a mechanical moving stage enables automated sampling and imaging applications. We developed a robotic platform, which is based on RepRap 3D-printer components, and therefore easy to reproduce and to adopt for custom prototypes. The minimal step width of the Open LabBot is 12.5 μm, and the sampling dimensions (x, y, z) are 18 × 15 × 20 cm. Adjustable rails in an aluminium frame construction facilitate the mounting of additional parts such as sensors, probes, or optical components. The Open LabBot uses industry-standard G-code for its control. The simple syntax facilitates the programming of the movement. We developed two programs: 1) LABI-Imaging, for direct control via a USB connection and the synchronization with MS data acquisition. 2) RmsiGUI, which integrates all steps of mass spectrometry imaging: The creation of G-code for robot control, the assembly of imzML files from raw data and the analysis of imzML files. We proved the functionality of the system by the automated sampling and classification of essential oils with a PlasmaChip probe. Further, we performed an ambient ionization mass spectrometry imaging (AIMSI) experiment of a lime slice with laser desorption low-temperature plasma (LD-LTP) ionization, demonstrating the integration of the complete workflow in RmsiGUI. The design of the Open LabBot and the software are released under open licenses to promote their use and adoption in the instrument developers’ community.

Compared to conventional allothermal gasification of solid fuels (e.g. biomass, charcoal, lignite etc.), plasma-assisted gasification offers an efficient method to apply energy into the gasification process to increase the flexibility of operation conditions and to increase the reaction kinetics. In particular, non-thermal plasmas (NTP) are promising, in which thermal equilibrium is not reached and electrons have substantially higher mean energy than gas molecules. Thus it is generally assumed that in NTP the supplied energy is utilized more efficiently for generating free radicals initiating gasification reactions than thermal plasma processes. In order to investigate this hypothesis, we compared purely thermal to non-thermal plasma assisted gasification of biomass in steam in a drop tube reactor at atmospheric pressure. The NTP was provided by means of gliding arcs between two electrodes aligned in the inlet steam flow. Electric power of about 1 kW was supplied using a high voltage generator operating at frequencies between 70 and 150 kHz and voltage amplitudes up to 10 kV. A laser-assisted optical method (Raman spectroscopy) was applied for measuring the gas temperature both in the conventionally heated steam and flow-down of the visible plasma filaments of the gliding arcs. Reaction yields and rates were evaluated using these measured gas temperatures. The first experimental results have shown that the non-thermal plasma not only promotes the carbon conversion of the fuel particles, but also accelerates the reaction kinetics. The carbon conversion is increased by nearly 10% using wood powder as the fuel. With charcoal powder more than 3% are converted into syngas.

High temperature Ni-superalloys are limited by reliance on critical elements and complex processing steps. High entropy alloys (HEAs) have demonstrated stable single/dual phase microstructures with strong ordering tendencies. A dual phase (FCC+BCC) Al0.5Co0.5CrFeNi1.5Ti0.25 alloy (developed using CALPHAD) was tested for room and high temperature compression behavior. The microstructure mainly comprises of coarse ordered FCC(L12) surrounding decomposed lamellae of ordered FCC(L12) and BCC(L21) phases, which coarsened upon annealing at high temperature (1100 °C) into a bi-continuous structure of disordered FCC+BCC(B2). Additionally, cold rollability of the cast alloy increased from <5% to ~40% after annealing, with a corresponding softening observed in room temperature compression mainly due to disordering of FCC and BCC phases. Peak flow stresses of 793.45MPa, 535.12MPa, and 324.40MPa were achieved at 800oC, 900oC, and 1000oC respectively for the high temperature annealed alloy.

This paper analyses the viability of different solutions to passively augment the axial stiffness of a horizontal axis radial levitation passive magnetic bearing (PMB) with topology previously studied. The zero-field cooling (ZFC) of high-temperature superconductor (HTS) bulks promotes higher magnetic impulsion and levitation forces and lower electromagnetic losses than with the field-cooling (FC), but on the other hand, the guiding stability is much lower than with FC. Because of stability reasons, FC was adopted in most superconducting maglev systems. The trend of this research group has been to develop an HTS ZFC horizontal axis radial levitation PMB presenting notable levitation forces with reduced electromagnetic losses, defined by a topology that creates guiding stability. Previous work has shown that even optimizing the bearing geometry to maximize magnetic guidance forces, could not be enough to guarantee the axial stiffness required for many applications. First, the extent to which guidance forces are augmented by increasing the number of HTS bulks in the stator is evaluated. Then, the axial stiffness augmentation by passively adding two limiting permanent magnet (PM) rings is evaluated. Results show that the axial stiffness is highly augmented by adding limiting PM rings with no significant additional investment. This change enables using the studied ZFC superconducting PMB in high-precision axial stability applications, such as precision gyroscopes, horizontal axis propellers and turbines.

Improper sitting positions are known as the primary reason for back pain and the emergence of musculoskeletal disorders (MSD) among individuals who spend prolonged time working with computer screens, keyboards, and mice. At the same time, it is well understood that automated technological tools can play an important role in the process of unhealthy habit alteration, so plenty of research efforts are focused on research and technology development (RTD) activities that aim to provide support to the prevention of back pain or the development of MSD. Here, we report on creating a new resource in support of RTD activities aiming at the automated detection of improper sitting positions. It consists of multimodal multisensory recordings of 100 persons made with a video recorder, camera, and wrist-attached sensors that capture physiological signals (PPG, EDA, Skin temperature), as well as motion sensors (three-axis accelerometer). Our multimodal multisensory dataset (MMD-MSD) opens new opportunities for modeling the body stance (sitting posture and movements), physiological state (stress level, attention, emotional arousal, valence), and performance (success rate on the Stroop test) of people working with a computer. Finally, we demonstrate two use cases: improper neck posture detection from pictures and cognitive load detection from physiological signals.

The various methods used to choose the profile shift coefficients, primarily the so-called equalizations, were based on assumed advantages without physical evidence proving them. In this paper a new calculation method is presented for determining profile shift coefficient. The procedure gives the pair of values ​​of the profile shift coefficients, in which case, under the given load, the resulting bending stress will be of the lowest possible value.

We report a preliminary exploration on the low-pressure Ar-O2 plasma generated by low-frequency alternating current (AC) power supply in the low-temperature Plasma Experimental Power Supply (CTP-2000S) for the first time. The electron density 〖(n〗_e), the electron temperature 〖(T〗_e) and the electron energy distribution function (EEDF) are measured by the single Langmuir probe in this experiment. Experimental results show that the ne increases with gas pressure rising, while the ne decreases with the oxygen concentrations rising. And, a plasma density peak is also observed with the AC power supply increase. A comparison between this work and the previous results by RF source suggests that the low-frequency AC power supply may be very fruitful exploration to generate the low-pressure plasma.

High-resolution (2 km) high-frequency (hourly) SST data from 2015-2020 provided by the Advanced Himawari Imager (AHI) onboard the Japanese Himawari-8 geostationary satellite positioned over 140.7°E were used to study spatial and temporal variability of the China Coastal Front (CCF) in the East China Sea. The hourly SST data were processed with the Belkin and O’Reilly (2009) algorithm to generate long-term mean monthly maps of SST gradient magnitude (GM) and frontal frequency (FM) using a GM threshold of 0.1°C/km. Horizontal structure of SST field in the vicinity of the CCF was investigated from cross-frontal distributions of SST along 8 parallels from 31°N to 24°N. The high resolution (2 km) monthly distributions of SST along these 8 parallels were used to determine inshore and offshore boundaries of the CCF and calculate the CCF strength defined as the total cross-frontal SST step dSST=Offshore SST – Inshore SST. The CCF emerges in November, fully develops in December and peaks in strength in January-February. The front’s fragmentation and shrinking/weakening begins in February and March, respectively. In winter (December-February), the front’s strength dSST exceeds 5°C offshore the Zhejiang-Fujian coast and could be as high as 7.5°C when nearshore waters cool down to 7°C. In winter, the front’s strength decreases downstream from 31°N to 24°N. The CCF changes its physical nature as the seasons progress. In winter, the CCF is a water mass front between cold and fresh water coming from the north and warm and salty water coming from the south. In summer, the CCF becomes a coastal upwelling front maintained largely by southerly winds. In winter, the CCF’s cross-frontal structure in the SST field is ramp-shaped, with SST increasing monotonously in the offshore direction. In summer, the CCF’s cross-frontal structure in the SST field is V-shaped or U-shaped, featuring a minimum SST formed by cold upwelled water at some distance from the shore. Thus, the summer SST structure effectively consists of two fronts, a nearshore and offshore, with a minimum SST in-between. Across the inshore/offshore front, the SST decreases/increases in the offshore direction. The local bathymetry, especially the relatively steep shelf slope between 20-m and 50-m isobath, steers the front, which does not meander in winter offshore the Zhejiang-Fujian coast. As the cold season progresses, the front’s axis gradually shifts into deeper waters, from ~20 m to ~50 m.

Precise monitoring of different environmental parameters and contaminations during food processing and storage is a key factor for maintaining its safety and nutritional value. Thus, developing reliable, efficient, cost-effective sensor devices for these purposes is of utmost importance. In this paper, we show that Poly-(diallyl-dimethylammonium chloride)/reduced Graphene oxide (PDAC/rGO) films produced by a simple Layer-by-Layer deposition can be effectively used to monitor temperature, relative humidity and the presence of volatile organic compounds as indicators for spoilage odors. At the same time, they show potential for electrochemical detection of organophosphate pesticide dimethoate. By monitoring the resistance/impedance changes during temperature and relative humidity variations or upon the exposure of PDAC/rGO films to methanol, good linear responses were obtained in the temperature range of 10-100 °C, 15-95 % relative humidity, and 35 ppm - 55 ppm of methanol. Moreover, linearity in the electrochemical detection of dimethoate is shown for the concentrations in the order of 102 µmol dm−3. The analytical response to different external stimuli and analytes depends on the number of layers deposited, affecting sensors’ sensitivity, response and recovery time, and long-term stability. The presented results could serve as a starting point for developing advanced multimodal sensor devices and sensor arrays with high potential for analytical applications in food safety and quality monitoring.

The study of long-term average weather patterns is known as climatology. It is a distinct field of study from meteorology and can be broken down into several subdivision. In order to predict the future, the knowledge of climatology is essential. In other words, with the help of climatology, we can figure out how likely it is that snow and hail will fall to the ground, and how much solar thermal radiation can reach a certain location etc. Climatology often focuses on how the climate has changed over time and how it has affected people and events. Both meteorology and climatology fall under the general term "meteorology", in particular, they are subdivision of research in the same field. In case of predicting the weather, meteorologists use variables such as humidity, air pressure, and temperature. This article's primary objective is to familiarize engineers with the fundamentals of climate and its processes so that they can effectively apply this knowledge to comprehend the climatic impact on water resources systems.

To understand great disparities in disease outcomes between CIVID-19 patients, we explore infection and host responses in kinetics. From existing data, we deduced a model that the lungs are damaged by rapidly rising flow resistance as a result of retaining white blood cells in lung tissues. The retention of white blood cells is initially triggered by viral infection but aggravated by injuries caused by low temperature. Lungs are initially damaged by fluid leakage, rapidly followed by extruding blood into alveolar spaces. The step of blood extruding is predicted to take place in a very short time. Our simulations show that as little as 0.1% retention of white blood cells in the lungs can lead to their failure in 5 to 10 days. The small degrees of imbalance implies that this imbalance could be corrected by a large number of factors that are known to reduce flow resistance. The model implies that the top priority is maintaining blood micro-circulation and preserving organ functions in the entire disease course, especially after the virus has spread the whole lungs. From exploring a large number of hypothetical infection modes, we propose preventive, mitigating and treatment strategies for ultimately ending the pandemic. The first strategy is avoiding exposures that could result in widespread damages to lungs and taking post exposure mitigating measures that would reduce disease severity. The second strategy is reducing death rate and disability rate from the current levels to one tenth for infected patients by using multiple factors health optimization method. The double reduction strategies are expected to generate a series of chain reactions that favor mitigating or ending the pandemic. Some reactions include a big reduction of the amount of viral discharges from infected patients into the air, the avoidance of panic, chronic stress and emotional distress, and cross-infections which are expected in quarantines. The double reductions would have a final effect of ending the pandemic.

Meixner's historical remark in 1969 "... it can be shown that the concept of entropy in the absence of equilibrium is in fact not only questionable but that it cannot even be defined...." is investigated from today's insight. Several statements --such as the three laws of phenomenological thermodynamics, the embedding theorem and the adiabatical uniqueness-- are used to get rid of non-equilibrium entropy as a primitive concept. In this framework, Clausius inequality of open systems can be derived by use of the defining inequalities which establish the non-equilibrium quantities contact temperature and non-equilibrium molar entropy which allow to describe the interaction between the Schottky system and its controlling equilibrium environment.

This study describes the properties of high-T_c cuprates by introducing rotating holes that are created by angular momentum conservations on a 2D CuO₂ surface, and which have a different mass from that of a normal hole because of the magnetic field energy induced by the rotation. This new particle called a macroscopic Boson describes the doping dependences of pseudo-gap temperature and the transition temperature at which an anomaly metal phase appears and describes the origin of the pseudo-gap. Furthermore, this study introduces a new model to handle many-body interactions, which results in a new statistic equation. This statistic equation describing many-body interactions accurately explains why high-T_c cuprates have significantly high critical temperatures. Moreover, a partition function of macroscopic Bosons describes the properties of anomaly metal phase, which sufficiently agree with experiments. Note that, the calculations were conducted, using the result from our previous study that analytically describes the doping dependence of T_c. By introducing a macroscopic Boson and the new statistical model for many-body interactions, this study uncovered the mystery of high- T_c cuprates, which have been a challenge for many researchers. An important point is that, in this study, pure analytical calculations are consistently conducted, which agree with experimental data well (i.e., they do not use numerical calculations or fitting methods but use many actual physical constants).

Molecular dynamics simulations were performed to examine the impact of temperature (ranging from 250K to 350K) on the structural behavior of cellulose chains when dissolved in an aqueous cuprammonium hydroxide Cuam solvent system. By monitoring the root mean square deviation (RMSD) and radius of gyration (Rg) values at each temperature, we found that the geometric deformation of the cellulose chains changed significantly at T=300K. In contrast, Rg and RMSD values remained stable at temperatures in the range of 250K, 270K and the range of 330K, 350K. Calculating the interaction energy between the solvent and cellulose chains revealed that temperature significantly influences the cellulose dissolution process in the Cuam solvent system and that T=300K is an efficient temperature for its dissolution. The number of intra- and interchain hydrogen bonds was also calculated as a function of temperature, and the analysis confirmed that there is no breakage of these bonds at temperatures below 300 K (i,e: 250K, 270K) and above 310 K (I,e, : 330K and 350K) either between two native chains or between a native chain and another derivative.

We reviewed various physical and biological manifestations of an unprecedented large-scale water temperature anomaly that emerged in the Northeast Pacific in late 2013. The anomaly dubbed “The Blob” persisted through 2014-2016, with some signs of its persistence through 2017-2018 and a possible reemergence in 2019. The tentative timeline of The Blob’s successive appearances around the Northeast Pacific is suggestive of its advection by currents around the Gulf of Alaska, along the Aleutians, into the Bering Sea, and eventually to the Bering Strait. During the initial phase of The Blob’s development in 2013-2014, advection along the Polar Front might have played a certain role. The extreme persistence and magnitude of The Blob resulted in numerous and sometimes dramatic ecosystem responses in the eastern Bering Sea. The multi-year duration of The Blob might have preconditioned the Bering Sea for the record low seasonal sea ice extent during the winter of 2017-2018 and disappearance of the cold pool in 2016 and 2018 that profoundly affected zooplankton, invertebrates, fishes, sea birds, and marine mammals. Comparison of time-series of population responses across trophic levels suggests that The Blob lowered primary production during spring, increasing small copepod production and jellyfish, and reducing energy transfer efficiently to higher trophic levels. While the Bering Sea’s water temperature, seasonal sea ice, and cold pool seem to return to the long-term mean state in 2022, it remains to be seen if the Bering Sea ecosystem will completely recover. The two most likely alternative scenarios envision either irreversible changes or hysteresis recovery.

The article presents results of research consisting in an attempt to assess the influence of temperature, heating time and cooling method on microstructure and residual strength properties of steel previously tempered during the production process. Simulated environmental conditions to which high-strength bolts, commonly used in steel construction, were subjected, were intended to reflect conditions of a natural fire that may occur in public facilities where the obligation to ensure safety of users and rescue teams is of key importance, also required by law. Furthermore, the tests carried out also comprised a simulated effect of a rescue and firefighting operation using shock, rapid cooling of some of the heated bolts. Samples cut out from the tested bolts, after they were properly prepared, were subjected to microstructural tests using light microscopy, scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), phase analysis with the use of an X-ray diffractometer (XRD) and quantitative analysis of the microstructure involving, inter alia, measuring the surface area of grains, their equivalent diameter and mean diameter. As a result of the tests, considerable microstructure changes were identified occurring in the bolt material as a result of exposing it to fire conditions, leading to a change in key, from the point of view of structural safety, mechanical properties. The results of the microstructure tests were compared with the results of previous strength tests, including hardness of the material after the heat treatment and the residual tensile strength of the material Rm. A conducted comparative analysis showed a significant effect of all such factors as the temperature level of the simulated fire, its duration and the fire-fighting method on the mechanical properties of bolts. Results obtained were provided with required comments and the concept of using the microstructure for the post-fire assessment of steel structures was referred to.

Rapid and extensive urbanization has adversely impacted humans and ecological entities in the recent decades through a decrease in surface permeability and the emergence of urban heat islands (UHI). While detailed and continuous assessments of surface permeability and UHI are crucial for urban planning and management of landuse zones, they have mostly involved time consuming and expensive field studies, and single sensor derived large scale aerial and satellite imageries. We demonstrated the advantage of fusing imageries from multiple sensors for landuse and landcover (LULC) change assessments as well as for assessing surface permeability and UHI emergence in Tirunelveli, Tamilnadu, India. Cartosat-2 and Landsat-7 ETM+ imageries from 2007 and 2017 were fused and classified using a Rotation Forest (RF), while surface permeability and temperature were quantified using Soil-Adjusted Vegetation Index (SAVI) and Land Surface Temperature (LST) index, respectively. Fused images exhibited higher classification accuracies than non-fused images, i.e. overall kappa coefficient values 0.83 and 0.75, respectively. We observed an overall increase of 20 km2 (45%) in the coverage of urban (dry, real estate plots and built-up) areas, while a decrease of 27 km2 (37%) for vegetated (cropland and forest) areas in Tirunelveli between 2007 and 2017. The SAVI values indicated an extensive decrease in surface permeability for Tirunelveli overall (0.4) and also for almost all LULC zones. The LST values exhibited an associated overall increase (1.30C) of surface temperature in Tirunelveli with the highest increase (2.40C) for urban built-up areas between 2007 and 2017. The SAVI-LST combined metric depicted the Southeastern built-up areas in Tirunelveli as a potential UHI hotspot, while a caution for the Western riparian zone for UHI emergence in 2017. Our results provide important metrics for surface permeability and UHI monitoring, and inform urban and zonal planning authorities about the advantages of satellite image fusion.

We extensively studied serigraphic screen-printed commercial silver flake inks loaded with silicon inclusions in order to achieve pinning at the grain boundaries. Based on grain size measurements using electron backscattered diffraction (EBSD), commercial silver ink with silicon microparticle content of 5 wt.% shows a significant grain growth retardation compared to the pristine silver ink, which stabilizes electrical conductivity up to 700 ◦C via Zener pinning mechanism. The modified silicon-loaded silver ink experiences a two times increase in grain size when heated up to 700 ◦C, compared to a seven times increase for the pristine silver ink. In turn, this enables operation temperatures significantly higher than the conventional operational window of microparticle-based silver inks, which are usually limited to 400 ◦C. Using isothermal exposures of 10 minutes up to 4 hours this phenomenon is observed at temperatures ranging from 250 ◦C to 900 ◦C. The electrical conductivity stability, grain size evolution and oxide contents were studied up to 4 hours. The activation energy of silver ink with silicon inclusions is 54% lower than for the pristine silver ink due to pining effect, which retards grain growth via the Zener mechanism. Most importantly, the electrical resistivity becomes stable up to 700 ◦C, which is more than twice the operation limit for off-the-shelf screen-printable silver flake inks. Hence, we demonstrate that adding controlled amounts of silicon particles to silver inks towards grain structure engineering can open new vistas of possibilities for screen-printed metallic inks.

Surface processes such as coatings, corrosion, photocatalysis, and tribology are greatly diversified by acid-base interaction at the surface overlayer. This study focuses on the action of metallic copper surface as an electron donor/acceptor related to inactivation of viruses; it was found that regarding Cu2O or Cu materials electrostatic interaction plays a major role in virus inactivation. We applied TPPE method to clarify the mechanism of electron transfer (ET) occurring at light irradiated copper surfaces. The TPPE characteristics was strongly influenced by the environments, which correspond to the temperature and environment dependence of the total count of emitted electrons in the incident light wavelength scan (PE total count, NT), the photothreshold, and further the activation energy (E) analyzed from Arrhenius plot of NT values obtained in the temperature-increase and subsequent temperature-decrease processes. In this study we reexamined the dependence of the TPPE data from two types of Cu metal surfaces: Sample A, which was mechanically abraded in alcohols, water, and air, and Sample C, which was only ultrasonically cleaned in these liquids. The NT for both Samples slowly increased with increasing temperature, reached a maximum (NTmax) at 250C (maximum temperature, Tmax), and after that decreased. For Sample A the NTmax value decreased in the order H2O > CH3OH > C2H5OH > (CH3)2CHOH > C3H7OH, although the last alcohol gave Tmax = 100C, while with Sample C the NTmax value decreased in the order: C3H7OH > (CH3)2CHOH > C2H5OH > CH3OH > H2O. Interestingly, both orders of the liquids were completely opposite: this means that Cu surface can possess two-way character. The NT intensity was found to be strongly associated with the change of the hydroxyl group (Cu-OH) to the oxide oxygen (O2) in the O1s spectra in the XPS measurement. The difference between the above orders was explained by the acid-base interaction mode of the Cu-OH group with the adsorbed molecule on the surfaces. The H2O adsorbed on Sample A produces the electric dipole Cu-OH+---:OH2 (--- hydrogen bond), while the C3H7OH and (CH3)2CHOH adsorbed on Sample C produce ROH+---:O(H)-Cu (R = alkyl groups). Gutmann’s acceptor number (AN) representing the basicity of the liquid molecules was found to be related to the TPPE characteristics: (CH3)2CHOH (33.5), C2H5OH (37.1), CH3OH (41.3), H2O (54.8) (the AN of C3H7OH could not be confirmed). With Sample A the values of NTmaxa and EaUp1 both increased with increasing AN (Up1 means the 1st temperature-increase process). On the other hand, with Sample C the values of NTmaxc and EcUp1 both decreased with increasing AN. These findings suggest that Sample A acts as an acid, while Sample C functions as a base. However, in the case of both types of Samples A and C the NTmax values were found to increase with increasing EUp1. It was explained that the EUp1 values depending on the liquids originate from the difference in the energy level of the hydroxyl group radical at the surface denoted. This is able to attract electrons in the neighborhood of the Fermi level of the base metal by tunnelling. After that due to Auger emission electrons are released, leading to the ET in the overlayer. These electrons are considered to have a strong ability of reducibility.

This article discusses laser-induced laboratory-air plasma measurements and analysis of hydroxyl (OH) ultraviolet spectra. New experiments with Q-switched laser pulses illustrate occurrence of molecular recombination spectra for time delays of the order of several dozen of microseconds after plasma initiation. The computation of the emission spectra utilizes line strength data that are communicated as a supplementary file. Applications of detailed OH computations include laser-induced plasma and combustion analyses, to name but two applications.

Climate change has emerged as a crucial global issue that significantly threatens the survival of plants. In particular, low temperature (LT) is one of the critical environmental factors that influence plant morphological, physiological, and biochemical changes during both the vegetative and reproductive growth stages. LT, including abrupt drops in temperature, as well as winter conditions, can cause detrimental effects on the growth and development of tomato plants, ranging from sowing, transplanting, truss appearance, flowering, fertilization, flowering, fruit ripening, and yields. Therefore, it is imperative to understand the comprehensive mechanisms underlying the adaptation and acclimation of tomato plants to LT at the morphological and the molecular levels. In this review, we discuss the previous and current knowledge of morphological and physiological changes, which contains major factors and traits associated with the LT stress response during the period of the vegetative and reproductive growth and development in tomato plants. Moreover, we highlight recent advances in the understanding of physiological and biochemical responses, and molecular mechanisms, including LT perception, signaling transduction, gene regulation, and fruit ripening and epigenetic regulation. The comprehensive understanding of LT response provides a solid basis to develop the LT-resistant varieties for sustainable tomato production under the ever-changing temperature fluctuations.

Experiments to measure a single molecule/particle, i.e. an individual molecule/particle, at room temperature or under physiological conditions without immobilization, for example on a surface, or without significant hydrodynamic flow have so far failed. This failure has given impetus to the underlying theory of Brownian molecular motion towards its stochastics due to diffusion. Quantifying the thermodynamic jitter of molecules/particles inspires many and forms the theoretical basis of single-molecule/single-particle biophysics and biochemistry. For the first time, our simulation results for a live cell (cytoplasm) show that the tracks of individual single molecules are localized in Brownian motion, while there is fanning out in fractal diffusion (anomalous diffusion).

A reduced order model is developed to monitor aeroengines condition (defining their degradation from a baseline state) in real-time, by using data collected in specific sensors. This reduced model is constructed by applying higher order singular value decomposition plus interpolation to appropriate data, organized in tensor form. Such data are obtained using a detailed engine model that takes the engine physics into account. Thus, the method synergically combines the advantages of data-driven (fast online operation) and model-based (the engine physics is accounted for) condition monitoring methods. Using this reduced order model as surrogate of the engine model, two gradient-like condition monitoring tools are constructed. The first tool is extremely fast and able to precisely compute `on the fly’ the turbine inlet temperature, which is a paramount parameter for the engine performance, operation, and maintenance, and can only be roughly estimated by the engine instrumentation in civil aviation. The second tool is not so fast (but still reasonably inexpensive) and precisely computes both, the engine degradation and the turbine inlet temperature at which sensors data have been acquired. These tools are robust in connection with random noise added to the sensors data and can be straight forwardly applied to other mechanical systems.

Fixed offshore wind turbines continue to be developed for high latitude areas where not only wind and wave loads need to be considered, but also moving sea ice. Current rules and regulations for the design of fixed offshore structures in ice-covered waters do not adequately consider effects of ice loading and its stochastic nature on fatigue life of the structure. Ice crushing on such structures results in ice-induced vibrations, which can be represented by loading the structure using a variable-amplitude loading (VAL) sequence. Typical offshore load spectra are developed for wave and wind loading. Thus, a combined VAL spectrum is developed for wind, wave, and ice action. To this goal, numerical models are used to simulate the dynamic ice-, wind-, and wave-structure interaction. The stress time-history at an exemplarily selected critical point in an offshore wind energy monopile support structure is extracted from the model and translated into a VAL sequence, which can then be used as a loading sequence for the fatigue assessment or fatigue testing of welded joints of offshore wind turbine support structures. This study presents the approach to determine combined load spectra and standardized time series for wind, wave, and ice action.

This paper aims to present the basic assumptions for creation of social Fröhlich condensate and attract attention of other researchers (both from physics and socio-political science) to the problem of modelling of stability and order preservation in highly energetic society coupled with social energy bath of high temperature. The model of social Fröhlich condensation and its analysis are based on the mathematical formalism of quantum thermodynamics and field theory (applied outside of physics). The presented quantum-like model provides the consistent operational model of such complex socio-political phenomenon as Fröhlich condensation. The model of social Fröhlich condensation is heavily based on theory of open quantum systems. Its consistent elaboration needs additional efforts. Evidence of such phenomenon as social Fröhlich condensation is demonstrated by stability of modern informationally open societies Approaching the state of Fröhlich condensation is the powerful source of social stability. Understanding its informational structure and origin may help to stabilize the modern society. Application of the quantum-like model of Frhlich condensation in social and political sciences is really the novel and original approach to mathematical modeling of social stability in society exposed to powerful information radiation from mass-media and internet based sources.

It is known that the elastic characteristics of polyamides change with increasing temperature, in particular, the Young's modulus decreases significantly. This fact is practically not taken into account in design calculations of metal-polymer plain (MP) bearings, operating under conditions of the boundary and dry friction. The purpose of the study is the analysis of the effect of temperature on the change of the Young's modulus and, accordingly, the contact strength and triboresource according to the developed method of calculating MP bearings. MP bearings with a bushing made of polyamide PA6 reinforced with glass or carbon dispersed fibers were investi-gated. Quantitative and qualitative regularities of change of the maximum contact pressures and resource of the bearings at temperature increase under conditions of boundary and dry friction are established. The pressures in the bearing bushing made of PA6+30GF will be lower than for the bushing made of PA6+30CF. The resource of the bushing made of PA6+30CF will be significantly greater than for PA6+30GF. For thermoplastic polymers, the increase in temperature will have a useful practical effect due to the decrease in the rigidity of the polymer composites of the bearing bushing.

Most of the commonly used Ionic Liquids (ILs) contain bulky organic cations with suitable anions. With our COMPLET (Concept of Melting Point Lowering due to Ethoxylation), we follow a different approach. We use simple, low-toxic, cheap and commercially available anions of the type Cx(EO)yCH2COO– to liquefy presumably any simple metal ion, independently of its charge. In the simplest case, the cation can be sodium or lithium, but synthesis of Ionic Liquids is also possible with cations of higher valences such as transition or rare earth metals. Anions with longer alkyl chains are surface active and form surface active ionic liquids (SAILs), which combine properties of ionic and nonionic surfactants at room temperature. They show significant structuring even in their pure state, i.e. in the absence of water or any other added solvent.

Thermal sterilization is generally avoided for 3-D printed components because of the relatively low deformation temperatures for common thermoplastics used for material extrusion-based additive manufacturing. 3-D printing materials required for high-temperature heat sterilizable components for COVID-19 and other applications demands 3-D printers with heated beds, hot ends that can reach higher temperatures than polytetrafluoroethylene (PTFE) hot ends and heated chambers to avoid part warping and delamination. There are several high temperature printers on the market, but their high costs make them inaccessible for full home-based distributed manufacturing required during pandemic lockdowns. To allow for all these requirements to be met for under $1,000, the Cerberus – an open source three-headed self-replicating rapid prototyper (RepRap) was designed and tested with the following capabilities: i) 200^oC-capable heated bed, ii) 500^oC-capabel hot end, iii) isolated heated chamber with 1kW space heater core and iv) mains voltage chamber and bed heating for rapid start. The Cereberus successfully prints polyetherketoneketone (PEKK) and polyetherimide (PEI, ULTEM) with tensile strengths of 77.5 and 80.5 MPa, respectively. As a case study, open source face masks were 3-D printed in PEKK and shown not to warp upon widely home-accessible oven-based sterilization.

In general, a superconductor has zero resistance, although it requires significant refrigeration or high pressures with high manufacturing costs, which prevents it into practical applications. In other words, solving these issues implies main superconducting researches. To solve these problems, this paper describes a new type of superconductivity, which is independent for temperatures and which operates without pressures. The principles of the presented system are as follows:First a voltage source, a current source and a load are connected in series. Then, the voltage of the voltage source is adjusted to balance the voltage of the load. Under this condition, the balance of the two voltages provides a zero voltage between the taps of the current source and the generated current from the voltage source becomes zero because of the internal infinite resistance of the current source. As a result, the electric powers generated by the two sources are zero, and therefore, the load cannot generate Joule heating because of energy conservation. However, the current from the current source (not the voltage source) is not zero; therefore, we can predict that the resistance of the load must be zero. As a theory, we derived a new electric field and transient attractive force, which result in a very short coherence of an electron pair because there is not the Coulomb repulsive force due to the existence of the above transient attractive force. Note that both the forces are derived by the Poisson equation, which implies that they cannot be compatible. Therefore, the pair combination energy from spins becomes extremely strong, which is not destroyed by the normal heat energy. Moreover, every center-of-mass motion of electron pair results in the Bose-Einstein condensation and the macroscopic wave function, which produces the London equation (i.e., the Meissner effect). Moreover, by introducing the equivalent circuit, this paper conducted numerical calculations. As a result, we could derive numerically zero resistance and responses for additional static magnetic fields as a discharged current, which implies the Meissner effect. Note that this paper has prepared Appendix section, which provides a guide to reproduce actual experiments and preliminary experimental results. These results in the Appendix indicate the zero resistances and Meissner effects.

Rapid growth and domestic migration to capital city, Kathmandu Metropolitan City (KMC), Nepal have amplified land-use transition to unmanaged and unplanned urbanization have exacerbated problems of Urban Heat Island (UHI) Effect. Increasing built up surfaces, means of transport and industrial activities are major results for increasing temperature in the city area as compared to other areas. This study focuses on forecasting Land Surface Temperature (LST) using both univariate and multivariate time series models. The primary goal is to predict the impact of climatic factors on the Urban Heat Island (UHI) effect, utilizing data from 1981 to 2019. We analyzed key factors including - (i) relative humidity, (ii) surface pressure, (iii) specific humidity, and (iv) wind speed sourced from the MEERA-2 dataset. A univariate model using exponential smoothing achieved a Mean Absolute Error (MAE) of 3.17°C and an R² score of 0.94, highlighting strong predictive accuracy. Additionally, the multivariate Prophet model, which incorporates trend and seasonal components, further refined the forecasting by integrating multiple climatic factors. This study aims provides valuable information via prediction for sustainable urban planning and landscape design in KMC and other 61 districts.

This paper provides a brief overview of how the Haug and Tatum Cosmological Model (HTC) outperforms the Λ-CDM model in numerous categories. In particular, we show why the HTC model is a strong competitor to the Λ-CDM model. For example, HTC appears to resolve the Hubble tension by making use of newly-discovered fundamental relationships between the CMB temperature, the Hubble parameter, and cosmological redshift. Moreover, HTC appears to better explain certain early universe telescopic observations than the Λ-CDM model.

The urban heat island effect (UHI) is among the major challenges of urban climate, which is continuously intensifying its impact on urban life and functioning. Against the backdrop of increasingly prolonged heatwaves observed in recent years, practical questions about adaptation measures in cities are growing - questions that traditional meteorological monitoring can hardly answer adequately. On the other hand, UHI has long been in focus of research interest, but due to the technological complexity of providing accurate spatially referenced data at high spatial resolution and the requirement to survey at strictly defined parts of the day, information provision is becoming a major challenge. This is one of the main reasons why UHI research results are less often used directly in urban spatial planning. However, advances in geospatial technologies, including unmanned aerial systems (UAS), are providing more and more reliable tools that can be applied to achieve better and higher quality information resources that adequately characterize the UHI phenomenon. This paper presents a developed and tested methodology for the rapid and efficient assessment and mapping of the effects of surface urban heat island (SUHI). It is entirely based on the integrated use of data from unmanned aerial systems (UAS)-based remote sensing methods, including thermal photogrammetry and GIS-based analysis methods. The study is following the understanding that correct SUHI research depends on a proper understanding of the urban geosystem its spatial and structural heterogeneity, as its functional systems, which in turn can only be achieved only by supporting the research process with accurate and reliable information resources. In this regard, the possibilities offered by the proposed methodological scheme for efficient geospatial registration of SUHI variations at the microscale, including the calculation of intra-urban SUHI intensity, are discussed in detail. The methodology builds on classical approaches for using Local Climate Zoning (LCZ), adding capabilities for precise delineation of individual zone types and for geostatistical characterization of the urban surface heat island (SUHI). Finally, the proposed scheme is based on state-of-the-art technological tools that provide flexible and automated capabilities to investigate the phenomenon at microscales, including by enabling flexible observation of its dynamics in terms of heat wave manifestation and evolution. Results are presented from a series of sequential tests conducted on the largest residential area in Bulgaria's capital city, Sofia, in terms of area and population, over a relatively long period from 2021 to 2024.

Selective Laser Melting (SLM) is a complex additive manufacturing process that requires precise control of thermal conditions to ensure the quality and reliability of produced parts. The main challenge lies in accurately predicting the thermal behavior during SLM, which is influenced by rapid heating and cooling cycles, high thermal gradients, and temperature-dependent material properties. This study addresses this challenge by developing a comprehensive thermal model for the SLM process of 316L stainless steel (316L SS) and Ti6Al4V titanium alloy using Finite Element Analysis (FEA) in Abaqus. The model incorporates temperature-dependent material properties and phase transformations to simulate the temperature distribution and thermal history during SLM. To validate the model, experimental studies were conducted using custom-designed argon chambers and stainless-steel powder. The experimental results showed strong agreement with the simulated melt pool dimensions and thermal histories, confirming the model's accuracy. Key findings include the model's ability to predict the effects of varying processing parameters such as laser power and scanning speed on thermal behavior and melt pool characteristics. This validated model serves as a valuable tool for optimizing SLM processing parameters, enhancing the un-derstanding of thermal phenomena in additive manufacturing, and improving the quality and reliability of manufactured parts. Due to budget constraints, experimental validation was initially performed only on 316L SS. This approach allowed for the tuning of the finite element model before extending its application to Ti6Al4V. The successful validation with 316L SS provides a solid foundation for applying the model to more challenging materials like Ti6Al4V, ensuring cost-effectiveness and safety in initial experimentation. The novelty of this research lies in its detailed and validated thermal model, which bridges the gap between experimental and numerical approaches in SLM. By accurately simulating and validating the thermal processes involved in SLM, this study contributes to the advancement of additive manufacturing technologies and offers practical insights for industrial applications.

Globalization and industrialization have significantly disturbed the environmental ecosystem, leading to critical challenges such as global warming, extreme weather events, and water scarcity. Forecasting temperature trends is crucial for enhancing the resilience and quality of life in smart sustainable cities, enabling informed decision-making and proactive urban planning. This research specifically targets Ahmedabad city in India and employs the Seasonal Auto Regressive Integrated Moving Average with eXogenous factors (SARIMAX) model to forecast temperatures over a ten-year horizon using two decades of real-time temperature data. The stationarity of the dataset was confirmed using the Augmented Dickey-Fuller test, and the Akaike Information Criterion (AIC) method helped identify the optimal seasonal parameters of the model, ensuring a balance between fidelity and predictive accuracy. The model achieved an RMSE of 1.0265, indicating high accuracy within the typical range for urban temperature forecasting. This robust measure of error underscores the model’s precision in predicting temperature deviations, which is particularly relevant for urban planning and environmental management. The findings provide city planners and policymakers with valuable insights and tools for preempting adverse environmental impacts, marking a significant step towards operational efficiency and enhanced governance in future smart urban ecosystems. Future work may extend the model's applicability to broader geographical areas and incorporate additional environmental variables to refine predictive accuracy further.

The results of numerical experiments with the chemistry-climate model of the Institute of Numerical Mathematics of the Russian Academy of Sciences - Russian State Hydro-Meteorological University (INM-RSHU CCM) in comparison with the MERRA2 reanalysis data are presented. To assess the impact of sea surface temperature (SST) on stratospheric processes and the ozone layer, numerical experiments were carried out for scenarios corresponding to the El Niño and La Niña Southern Oscillation phases. It is shown that the El Niño phase contributes to the enhancement of heat and mass transfer to the polar stratosphere, which strengthen the Brewer-Dobson circulation and the flux of wave activity that affect the zonal wind. As a result, during El Niño, the probability of sudden stratospheric warming increases and the stratospheric polar vortex (SPV) weakens, re-sulting in an increase in total polar stratospheric ozone. The La Niña phase, on the contrary, is accompanied by a weakening of heat and mass transfer from the troposphere to the stratosphere, as a result of which the stratospheric polar vortex strengthens and the total column ozone decreases. It is shown that the effect associated with the Southern Oscillation is more pronounced in the Northern Hemisphere than in the Southern Hemisphere. Numerical experiments were also carried out for scenarios in which the sea surface temperature was set corresponding to the early 1980s, and the results were compared with calculations in which the SST was set corresponding to the late 2010s. This allowed us to assess the influence of the multiyear trend in the SST increase on stra-tospheric processes and the ozone layer. It was shown that the SST increase is most pronounced in the Arctic, which corresponds to the phenomenon of "Arctic amplification", and therefore, the heat and mass transfer to the stratosphere increases in the Northern Hemisphere, which contributes to some weakening of the SPV and increase of the total column ozone. But, compared to the Southern Oscillation, the influence of the SST trend on the SPV and total column ozone is much weaker and is observed mainly in the Northern Hemisphere.

In the implementation of thermal enhanced oil recovery (TEOR) techniques, the temperature impact on relative permeability in oil - water systems is of special concern. Hence, developing a fast and reliable tool to model the temperature effect on two-phase oil - water relative permeability is still a major challenge for precise studying and evaluation of TEOR processes. To reach the goal of this work, two promising soft-computing algorithms, namely Group Method of Data Handling (GMDH) and Gene Expression Programming (GEP) were employed to develop reliable, accurate, simple and quick to use paradigms to predict the temperature dependency of relative permeability in oil - water systems (K_rw and K_ro). To do so, a large database encompassing wide-ranging temperatures and fluids/rock parameters, including oil and water viscosities, absolute permeability and water saturation, was considered to establish these correlations. Statistical results and graphical analyses disclosed the high degree of accuracy for the proposed correlations in emulating the experimental results. In addition, GEP based correlations were found to be the most consistent with root mean square error (RMSE) values of 0.0284 and 0.0636 for K_rw and K_ro, respectively. Lastly, the comparison of the performances of our correlations against those of the preexisting ones indicated the large superiority of the introduced correlations compared to previously published methods. The findings of this study can help for better understanding and studying the temperature dependency of oil - water relative permeability in thermal enhanced oil recovery processes.

Experiments to measure a single molecule/particle, i.e. an individual molecule/particle, at room temperature or under physiological conditions without immobilization, for example on a surface, or without significant hydrodynamic flow have so far failed. This failure has given impetus to the underlying theory of Brownian molecular motion towards its stochastics due to diffusion. Quantifying the thermodynamic jitter of molecules/particles inspires many and forms the theoretical basis of single-molecule/single-particle biophysics and biochemistry. For the first time, our simulation results for a live cell (cytoplasm) show that the tracks of individual single molecules are localized in Brownian motion, while there is fanning out in fractal diffusion (anomalous diffusion).

Large values and gradients of stresses and deformations, triggering concentrations of stresses and deformations, arise in the corner areas of a structure. The action of forced deformations, leading to the finite rupture of the contact between the elements of a structure, also triggers the concentration of stresses, while the rupture reaches an irregular point, a line on the area boundary. The theoretical analysis of the stress-strain state (SSS) of areas with angular cutouts in the boundary under the action of discontinuous forced deformations is reduced to the study of singular solutions to the homogeneous problem of the elasticity theory that has power-related features. The calculation of stress concentration coefficients in the domain of a singular solution to the elastic problem makes no sense. It is experimentally proven that the zone, that is close to the vertex of the angular cutout in the area boundary, has substantial deformations, rotations, and it corresponds to rising values of the first and second derivatives of displacements along the radius in cases of sufficiently small radii in the neighbourhood of the irregular point of the boundary. For such areas, it is necessary to consider the plane problem of the elasticity theory, taking into account the geometric nonlinearity under the action of forced deformations. This will allow analyzing the effect of relations between orders of values of deformations, rotations, and forced deformations on the form of the equation of equilibrium. The purpose of this work is to analyze the effect of relations of deformation orders, rotations, forced deformations on the form of the equilibrium equation in the polar coordinate system for a V-shaped area under the action of forced temperature-induced deformations with regard for the geometrical non-linearity and physical linearity.

Herpes simplex virus type 1 (HSV-1) is a lifelong pathogen characterized by asymptomatic latent infection in the trigeminal ganglia (TG) with periodic outbreaks of cold sores caused by virus reactivation in the TG and subsequent replication in the oral mucosa. While antiviral therapies can provide relief from cold sores, they are unable to eliminate HSV-1. We provide experimental results that highlight non-thermal plasma (NTP) as a new alternative therapy for HSV-1 infection that would resolve cold sores faster and reduce the establishment of latent infection in the TG. Additionally, this study is the first to explore the use of NTP as a therapy that can both treat and prevent human viral infections. We investigated the antiviral effect of NTP using an in vitro model for HSV-1 cold sores, involving the application of NTP from two separate devices to cell-free HSV-1, HSV-1-infected cells, and uninfected cells. We found NTP reduced the infectivity of cell-free HSV-1, reduced viral replication in HSV-1-infected cells, and diminished the susceptibility of uninfected cells to HSV-1 infection. This triad of antiviral mechanisms of action suggest the potential of NTP as a therapeutic agent effective against HSV-1 infection.

This paper studies the evaporative heat transfer characteristics of R744 at low temperatures in a horizontal smooth tube as a cascade refrigeration system (CRS) among hybrid cascade refrigeration systems (HCRSs). There is a lack of research on the low-temperature evaporative heat transfer characteristics of R744 under the operating conditions of evaporators used in actual CRSs used in supermarkets. Therefore, this study aims to provide basic data on the evaporative heat transfer characteristics of R744 in the evaporators of refrigerators used in supermarkets. The tube used in the evaporation experiment conducted herein was a smooth horizontal copper tube with an inner diameter and length of 11.46 mm and 8000 mm, respectively. The experimental pa-rameters were as follows: heat fluxes of 12–21.5 kW/m2, mass fluxes of 75–225 kg/(m2·s), and saturation temperatures of −50–−30 °C. The main results are summarized as follows. (1) When designing the R744 evaporator, the mass and heat fluxes must be maximized within the operating conditions, and the saturation temperature must be designed to be as low as possible. (2) The evaporative heat transfer coefficient of R744 can be predicted well by using the correlation formula of Chen at the evaporation temperature of −40 °C in the CRS.

Melting phase relations of the diamond-forming system olivine (Ol) – jadeite (Jd) – diopside (Di) – (Mg, Fe, Ca, Na)-carbonates (Carb*) – (C-O-H-fluid) are studied in experiments at 6.0 GPa in the polythermal section Ol74Carb*18.5(C-O-H)7.5 - Omp74Carb*18.5(C-O-H)7.5, where Ol = Fo80Fa20, Omp (omphacite) = Jd62Di38 and Carb* = (MgCO3)25(FeCO3)25(CaCO3)25(Na2CO3)25. Peritectic reaction of olivine and jadeite-bearing melt with formation of garnet has been determined as a physico-chemical mechanism of ultrabasiс-basiс evolution of the diamond-forming system. In the process CO2-component of the supercritical C-O-H-fluid can react with silicate components to form additional carbonates of Mg, Fe, Ca and Na. Solidus temperature of the diamond-forming system is depressed to 1000-1020°C by joint effect of the H2O-fluid and carbonate constituents thereof. The experimentally recognized peritectic mechanism of ultrabasiс-basiс evolution of the diamond-forming system explains the origin of the associated paragenetic inclusions of peridotite and eclogite minerals in diamonds as well as the xenoliths of diamond-bearing peridotites and eclogites of the kimberlitic deposits of diamond. The diamond-forming systems have formed with the use of material of the upper mantle native peridotite rocks. In this case the capacity of the rocks to run the peritectic reaction of olivine was transmitted with silicate components to the diamond-forming systems.

The effects of photon inertia on the determination of its trajectory were verified and the representation of a displacement mass characterized by the flow of the number of wavefronts and the decomposition of photon inertia into parts associated with translation and rotation motions was considered. It was found that with the relativistic increase of the photon's resistance to change its directional properties, it inhibits the relativistic trajectory of the second torque, of Minkowski, in an angular range of incidence. After synchronizations, in the OAM inversions, there are reductions of the inertia associated to the translational part that assumes classical predominance, where the relativistic trajectory is allowed while the photon offers less resistance to changes in its directional properties. The classical-relativistic variability of the photon inertia characterizes the classical or relativistic profile of the energy distribution in forms of motion, where adjustments of the rotational and translational parts can be performed as a function of the refractive index rate, temperature and angle of incidence. It was found that with increasing temperature of the refringent medium, the synchronizations displacement in the sense of the normal incidence. A specific vacuum temperature for the refringent medium was characterized, where the photon exhibits a classical-relativistic synchronization under all angles of incidence, characteristic of its immaterial state in vacuum.

Following the coronavirus disease 2019 (COVID-19) pandemic, several studies have examined the possibility of correlating the virulence of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2), the virus that causes COVID-19, to the climatic conditions of the involved sites; however, inconclusive results have been generally obtained. Although either air temperature or humidity cannot be independently correlated with virus viability, a strong relationship between SARS-CoV-2 virulence and the specific enthalpy of moist air appears to exist, as confirmed by extensive data analysis. Given this framework, the present study involves a detailed investigation based on the first 20–30 days of the epidemic before public health interventions in 30 selected Italian provinces with rather different climates, here assumed as being representative of what happened in the country from North to South, of the relationship between COVID-19 distributions and the climatic conditions recorded at each site before the pandemic outbreak. Accordingly, a correlating equation between the incidence rate of the pandemic and the average specific enthalpy of atmospheric air was developed, and an enthalpy-based seasonal virulence risk scale was proposed as a tool to predict the potential danger of COVID-19 spread due to the persistence of weather conditions favorable to SARS-CoV-2 viability. For practical applications, a conclusive risk chart expressed in terms of coupled temperatures and relative humidity (RH) values was provided, showing that safer conditions occur in case of higher RH at the highest temperatures, and of lower RH at the lowest temperatures. The proposed risk scale was in agreement with the available infectivity data in the literature for a number of cities around the world.

High temperature (HT) geothermal wells can provide green power 24h a day 7 days a week. Harsh environmental and operational conditions, long-term durability requirements of such wells require special cementitious composites for well construction. This paper reports a comprehensive assessment of geothermal cement composites in cyclic pressure function laboratory tests, field exposures in an HT geothermal well (300-350oC) as well as a numerical model to complement the experimental results. Performances of calcium-aluminate-cement (CAC)-based composites and calcium free cement were compared against reference Ordinary Portland Cement (OPC)/silica blend. The stability and degradation of the tested materials was characterized by crystalline composition, thermo-gravimetric, and elemental analyses, morphological studies, water-fillable porosity, and mechanical properties measurements. All CAC-based formulations outperformed the reference blend both in the function and exposure tests. The reference OPC/silica lost its mechanical properties during the 9-month well exposure through extensive HT carbonation, while properties of the CAC-based blends improved over that period. The Modified Cam-Clay (MCC) plasticity parameters of several HT cement formulations were extracted from triaxial and Brazilian tests and verified against the experimental results of function cyclic tests. These parameters can be used in well integrity models to predict field-scale behavior of the cement sheath under geothermal well conditions.

Cloth wearing seems so natural that everyone is self-deemed knowledgeable and has some expert opinions about it. However to clearly explain the physics involved, and hence to make predictions for clothing design or selection, turns out as demonstrated below to be quite challenging even for experts. Cloth is a multiphased, porous and anisotropic material system and usually in multilayers. Unlike ordinary engineering heat transfer problems, the human body acts as an internal heat source in a clothing situation, thus forming a temperature gradient between body and ambient, and the sign of this gradient often changes as the ambient temperature varies. Our body also perspires and the sweat evaporates, an effective body cooling process via phase change. To bring all the variables into analysis quickly escalates into a formidable task. This work attempts to unravel the problem from a physics perspective, focusing on several rarely noticed yet critically important mechanisms involved so as to offer a clear and accurate depiction of the principles in clothing thermal comfort.

Noninvasive in-situ monitoring of viscoelastic characteristics of corneal tissue at elevated temperatures are pivotal for mechanical property-informed refractive surgery techniques, including thermokeratoplasty and photorefractive keratectomy, requiring precise thermal modifications of the corneal structure during these surgical procedures. This study harnesses Brillouin light scattering spectroscopy as a biosensing platform to non-invasively probe the viscoelastic properties of ovine corneas across a temperature range of 25 - 70°C. By submerging the tissue samples in silicone oil, consistent hydration is maintained, allowing for their accurate sensing of temperature-dependent mechanical behaviors. We identify significant phase transitions in the corneal tissue, particularly beyond 40°C, likely due to collagen unfolding, marking the beginning of thermal destabilization. A subsequent transition, observed beyond 60°C, correlates with collagen denaturation. These phase transformations highlight the cornea's sensitivity to both physiologically reversible and irreversible viscoelastic changes induced by mild to high temperatures. Our findings underscore the potential of Brillouin biosensing technique for real-time diagnostics of corneal biomechanics during refractive surgeries to attain optimized therapeutic outcomes.

A simple line of reasoning, based on the most fundamental concepts of thermodynamics, yields some intriguing results for a better understanding of the processes occurring in the observable Universe. Gravitational mass must be continuously generated within an expanding thermodynamic system for this system to remain closed. The Second Law is a direct consequence of this production of mass. Simple expressions for the entropy and temperature of the Universe were obtained and the results agree well with observable values. Furthermore, it is demonstrated that the conservation laws within the Universe are independent of its energy density. Based on the solution for the quantum state of the Universe, it is conjectured that the Second Law is incomplete and must be complemented to a conservation law, which takes into account the growth of the amount of information within the Universe. Once the Second Law is complemented to a conservation law, the importance of mass generation within the Universe becomes well pronounced – not only gravitational effects play the role of an organising force, but also the amount of mass within the Universe defines both the amount of information within the Universe and the level of the Universe’s complexity.

In regions with low-temperature action transverse cracks can appear in asphalt pavements as a result of thermal stresses that exceed the fracture strength of materials used in asphalt layers. To better understand thermal cracking phenomenon, strength properties of different asphalt mixtures were investigated. Four test methods were used to assess the influence of bitumen type and mixture composition on tensile strength properties of asphalt mixtures: tensile strength using the Thermal Stress Restrained Specimen Test (TSRST) and the Uniaxial Tension Stress Test (UTST), flexural strength using the Bending Beam Test (BBT) and fracture toughness using the Semi-Circular Bending Test (SCB). The strength reserve behavior of tested asphalt mixtures was assessed as well. The influence of cooling rate on strength reserve was investigated and correlations between results from different test methods were also analyzed and discussed. It was observed that the type of bitumen is a factor of crucial importance to low-temperature properties of the tested asphalt concretes. This conclusion was proved by all test methods that were used. It was also observed that the level of cooling rate influences the strength reserve and, in consequence, resistance to low-temperature cracking. It was concluded that reasonably good correlations were observed between strength results for the UTST, BBT and SCB test methods.

Most astrophysicists today believe that the present universe was produced in a big bang. This article explores the big cycle of matter and energy in the universe, with the big bang as an important part of the cycle.The authors approve of the idea that the universe is gravitationally closed. That is, its average density is higher than the critical value. All the matter and radiation cannot fly out the closed universe.The 3k background radiation is a vast heat ocean in the closed universe, stable and eternal. It is not the afterglow of the thermal radiation of the decoupled fire ball, 380,000 years after the big bang, as many people believed so far. The big bang and the following big expansion drove the matter of more than 2×10¹² galaxies to the remote space. Their potential energies become higher and higher, while their huge kinetic energies that they derived from the big bang become smaller and smaller until drop down to zero. The galaxies will then return back one after another, passing the central region of the universe with tremendously great kinetic energies. They of course cannot all return back directly to their start point of the big bang and restore to the state of the original cosmic core. They will rush to pass the central region and fly to the other sides of the universe, and shuttle around the central part ceaselessly. From the big bang to the following expansion, to the numerous galaxies, to the more than 2×10²³ stars, and to the stars releasing huge nuclear energy due to their internal nuclear fusion each for about 10¹⁰ years, all these enormous processes are irreversible, resulting in enormous increase in entropy. These processes produce large amount of light and other radiations and pour them into the extremely vast heat ocean. These light and other radiations will also be shuttling ceaselessly in the vast heat ocean until, by their interaction with the rare dusts in the galaxies, they mingle into the 3K thermal radiation of the heat ocean. In all the galaxies, there are various black holes. Every black hole, since its birth, ceaselessly extracts the matter and radiation that approach it, and gets larger. In the above mentioned shuttling of all the galaxies, numerous stars and black holes in these galaxies have many chances to approach even meet each other. A black hole can annex other celestial bodies that it meets, including annex other black holes. All these processes carry on and on ceaselessly, resulting in the matter of these celestial bodies to concentrate again and again. The number of all the celestial bodies including the black holes reduces ceaselessly, and the mass of the survived black holes become larger, and their shuttling amplitudes become shorter. The larger black holes and the shorter amplitudes result in the rate of concentration of mass to be faster. Eventually, all the matter in the universe will be concentrated to form a tremendously large central black hole. The central black hole has an astonishingly large Schwarzschild sphere, absorbing the thermal radiation from the vast heat ocean very rapidly and ceaselessly until some threshold value of its internal energy is exceeded, and a new big bang breaks out. The black holes provide a way in the Universe to re-concentrate matter and energy again. Black holes are Maxwell’s demons in the Nature.

The formation and propagation of cracks occurs through irreversible dislocation movements at notches, material defects and grain boundaries. Since this process is partly thermally controlled, the resistance to dislocation movements at low temperatures increases. This slows both fatigue initiation and fatigue crack propagation. From recent experimental data, it can be seen that fatigue crack growth is accelerated below the fatigue transition temperature (FTT) that correlates with the ductile-brittle transition temperature (DBTT) found by well-known fracture mechanics tests, i.e., Charpy impact, fracture toughness, and CTOD. Hence, this study investigates the relation between FTT and DBTT in S500 high-strength steel base material and welded joints at low temperatures using fatigue crack growth, fracture toughness tests as well as scanning electron microscopy. From the tests, an almost constant decrease in fatigue crack propagation rate is determined with decreasing test temperature even below the DBTT.

This article explores the intersection of innovative leadership and climate change, aiming to provide outstanding contributions to the existing body of knowledge in this field. The article identifies the critical role of innovative leadership in driving sustainable solutions and strategies for addressing climate change. It examines the defining characteristics and behaviors of innovative leaders and explores how their transformative leadership approaches can create a positive impact on climate change mitigation and adaptation efforts. The article also highlights the importance of fostering innovation within organizations and societies to tackle the complex challenges posed by climate change. Through a comprehensive review of relevant literature and case studies, this article presents novel insights, theoretical frameworks, and practical implications for policymakers, organizations, and individuals involved in climate change leadership.

This paper explores the Wilsonian renormalization group of probe-D-branes, focusing on the Dirac-Born-Infeld (DBI) action. The analysis involves deriving the constant of motion and formulating the Wilsonian renormalization group equation. The study extends to the infrared regime, considering both zero and non-zero temperatures. Additionally, thermodynamic aspects related to the functional form of the grand potential are discussed. The investigation provides insights into the renormalization of probe-D-branes and their thermodynamic properties.

This work is a physical review, with elements of additions and thinning, on the methods of theoretical studies of nonlinear electrophysical phenomena in crystals with ion-molecular chemical bonds (CIMB). Crystals of this class include ionic dielectrics (characterized by high ionic conductivity), layered crystals, a special case of which are hydrogen-bonded crystals (HBC), defined as proton semiconductors and dielectrics (PSD).A scientific review (comparative analysis and justification of various approximations) was carried out on the methods of constructing and solving a generalized quasi-classical kinetic equation describing the mechanism of nonlinear relaxation polarization and conductivity processes in dielectric materials with ion-molecular chemical bonds (a special case is hydrogen-bonded crystals (HBC)) in a wide temperature range (1-1550 K) and polarizing field strengths (0.1-1000 V/m) at alternating field frequencies of the order of 1 kHz - 1000 MHz. The most important variant of the equations of the kinetic theory of dielectric relaxation in this work is the generalized non-linear by polarizing field quasi-classical kinetic equation of ionic (in HBC, proton) relaxation, based on the particle number balance equation (conductivity ions) in potential wells and having (in these models) the meaning of the ion current continuity equation (in HBC, protons), solved by the method of successive approximations by decomposition into infinite power series by degrees of a small dimensionless comparison parameter. It was found that in the area of ​ ​ weak fields (0.1-1 MW/m) at temperatures T = 50 - 550 K, for a number of ionic dielectrics (including HBC and similar dielectric properties and lattice structure) the generalized quasi-classical kinetic equation transforms to the linearized Fokker – Planck equation and, in the region of low (50-100K) and higher temperatures (250-550 K) begin to manifest non-linear polarization effects due to respectively proton tunneling (in the case of HBC) and volume charge relaxation (in the case of the HBC and for a wider class of ionic dielectrics). At ultra-low (1-10 K) temperatures in the region of weak fields (0.1-1 MW/m) and ultra-high temperatures (550-1550 K) in the region of strong fields (10-1000 MW/m), the contribution of this kind of effects to polarization is significantly enhanced. The effect of nonlinearities on relaxation times for microscopic acts of proton transitions across a potential barrier (assumed to be parabolic) is investigated. Nonlinear effects at volume-charge polarization in the hydrogen-bonded crystals (HBC) in alternating electric field, in radio frequency range are investigated. From the solution of the system of nonlinear Fokker-Planck equations (macroscopic kinetic equation) and Poisson, with blocking electrodes, using Fourier series, a recurrent (convenient for use in any approximation of perturbation theory) expression is constructed for complex amplitudes of relaxation modes of volumetric charge. Complex dielectric permittivity (CDP) is calculated as a series decomposition over even frequency harmonics of a variable field. The effect of quantum proton transitions and polarizing field parameters (strength, frequency) on the nonlinear properties of proton semiconductors and dielectrics has been established.