Brushless Direct Current Motors are significantly improved for using many electrical applications. The design investigation is increased year by year and most of the motor design researchers find out the superior efficiency of the BLDC motor. The traditional motor consumed more electrical power than BLDC motor. The design of BLDC motors that are compact, small, easy to control, save energy and light weight. Due to this fact, the design of BLDC motor should be analyzed to improve the motor characteristics performance. The research focuses on the design of BLDC motor performance using Taguchi Method and Response Surface Methodology (RSM) for Finite Element Method (FEM). Firstly, the Taguchi Method is applied to identify the optimization point of design parameters and consider using the reference model of actual BLDC electric fan motor with a rated power of 26Watts design. Based on the Taguchi Method to create the RSM is used to two-step optimization design performance using in FEM analysis. The performances of motor design proposed approach to provide the effeteness for motor design investigator. In this investigation aims the better structural performances in output power, torque, efficiency and torque ripple. The final design of proposed model achieved an energy efficiency is 10% higher than the reference design of prototype modes, the output power result is 10W higher this reference design. We can reduce the loss of the proposed motor design. Furthermore, the maximum torque can also increase the 0.032Nm of that design. The design simulation results were produced and studied by the FEM analysis of JMAG software. From the evaluation results, the configurations of reference model design are compared with the proposed design by using the three methods of motor design optimization showed the best characteristics for performance of motor investigation design.

This paper studies the optimization method of pump hydraulic performance based on the response surface method. A parametric model of impeller and diffuser is established. Three-dimensional optimization is carried out on the basis of the initial model obtained by one-dimensional design method. We select the pump hydraulic efficiency and the head as objective function and constraint function. Response surface models are constructed to analyze the relationship between the objectives and the design variables, and the global optimization of hydraulic performance is realized. According to the internal flow characteristics of pump, this paper proposes the strategy of two steps optimization, which aims at meridional plane and blade shape, respectively, to solve the problem of large numbers of design parameters and computational cost. The optimization results show that the hydraulic efficiency of pump increased by 3.7%, and the head is nearly the same.

For marine vessels, a propeller shaft system, also known as a propulsion shaft system, is an essential changer in engine torque and propeller thrust. The propeller shaft system is subjected to transverse, longitudinal, and torsional excitations during operation. These sources of excitations originate from alternating thrust generated by the propeller, operation of a propeller in a stern flow field which is non-uniform in time and space, misalignment of components such as shafts, bearings, and keyholes in the assembly, excitations in the form of rotational motion, and the whirling motion of the shafts. These dynamic excitations posed a challenging issue for the integrity and reliability of a marine vehicle. Thus, it is crucial to analyze the dynamic response of the propulsion shaft system. The dynamic analysis of the propulsion shaft system is typically conducted using numerical /analytical models. At present, Finite Element Model (FEM) as a numerical model plays a vital role in analyzing the dynamic response of the structure. The computed response and the modal parameters from the FE model are reliable only if accurate boundary conditions, such as stiffness, can be imposed on the model. However, the numerical FE model deviates from the experimental results because of uncertainties in the stiffness values of the bearings and other connectors. This paper uses the Response Surface Optimization (RSO) technique to estimate the unknown stiffness of the bearings used in the propulsion shaft system. The experimental model of the propeller shaft system is constructed from the steady-state response of the system using the step sine excitation. The natural frequencies and the amplitude of vibrations in the FE model are updated using the parametric RSO technique. The updated model shows that the difference in natural frequencies and vibration amplitude is less than 10% between the optimized and experimental models. Propeller Shaft, Vibrations, Optimization, Response Surface

In the process of sewage coagulation treatment, quartz sand is often used as a heavy medium to accelerate the settling rate of flocs, but it will adversely affect the removal efficiency of pollutants. The factors that affect the coagulation effect and can be controlled manually include the quartz sand dosage, coagulant dosage, sewage pH, stirring time, settling time, etc, their reasonable setting is critical to. This paper was to study the optimal conditions of quartz sand enhanced coagulation(QSEC), first, single-factor tests were conducted to preliminarily explore the optimal range of influencing factors, and then response surface methodology（RSM）tests were performed to accurately determine the optimums of significant factors. The results showed that the addition of quartz sand can’t improve the water quality of coagulation treatment, but it can significantly accelerate the coagulation settlement process, the quartz sand dosage, the coagulant dosage and sewage pH all impacted significantly on its coagulation effect, and existed inflection points. A model that could guide QSEC was obtained by RSM tests. The model optimization and experimental validation showed that the optimal QSEC conditions for treating domestic sewage were as follows: the polyaluminum chloride(PAC) dosage, cationic polyacrylamide(CPAM) dosage, the sewage pH, quartz sand dosage, stirring time and settling time were 0.97 g·L-1, 2.25 mg·L-1, 7.22, 2 g·L-1, 5 minutes and 30 minutes, respectively, and the turbidity of treated sewage was reduced to 1.15 NTU.

The design of curved surface sliders (CSS) based on the elastic response spectrum is done by iteration to find the combination of friction coefficient and displacement capacity which satisfies the condition that the maximum horizontal CSS force is equal to the horizontal force of the structure. Although this CSS design is valid it does not necessarily minimize structural acceleration. This paper therefore describes the optimum CSS design for minimum structural acceleration. All valid CSS designs and the optimum CSS design are represented by their associated trajectory in the elastic response spectrum plane which visualizes the optimization problem. The results demonstrate that the optimum CSS design is not obtained at maximum tolerated effective damping ratio. The subsequent sensitivity analysis describes how much the structural acceleration increases if the actual friction coefficient of the real CSS deviates from its optimum design value. The analysis points out that the increase in structural acceleration is approximately one order of magnitude smaller than the deviation in friction. The sensitivity data may be used by structural engineer to determine tolerable deviations in friction coefficient which still results in acceptable structural accelerations.

The overall cost of a hydropower plant is mainly due to the expenses for civil works, mechanical equipment (turbine and control units) and electrical components. The goal of a new draft tube design is to obtain a geometry that reduces investment costs, especially the excavation ones, but the primary driver is to increase the overall machine efficiency allowing for reduced payback time. In the present study, an optimization study of the elbow-draft tube assembly of a Kaplan turbine was conducted. A CFD model for the complete turbine has been developed and validated; next, an optimization of the draft tube alone was performed using a Design of Experiments technique; finally, several optimum solutions for the draft tube were obtained using a Response Surface technique aiming at maximizing pressure recovery and minimizing flow losses. A selection of optimized geometries was subsequently post-checked using the validated model of the entire turbine and a detailed flow analysis on the obtained results could make it possible to provide insight into the improved designs. It was observed that efficiency could be improved by 1% (in relative terms), and the mechanical power increased by 1,8% (in relative terms) with respect to the baseline turbine.

Boiler efficiency is called to some extent of total thermal energy which can be recovered from the fuel. Boiler efficiency losses are due to four major factors: the dry gas flux, the latent heat of steam in the flue gas, the combustion loss or the loss of unburned fuel, radiation and convection losses. In this research, the thermal behavior of boilers in gas refinery facilities is studied and their efficiency and their losses are calculated. The main part of this research is comprised of analyzing the effect of various parameters on efficiency such as excess air, fuel moisture, air humidity, fuel and air temperature, the temperature of combustion gases, and thermal value of the fuel. Based on the obtained results, it is possible to analyze and make recommendations for optimizing boilers in the gas refinery complex using response-surface method (RSM).

According to the honeycomb structure, the preliminary design of bionic wheel hub for finite element analysis, in the working condition of a wheel by the force is through the spokes pointing to the center, the working condition of two wheel by the force is through the two spokes pointing to the center, and the ordinary wheel stress and displacement value results compared, observed the maximum stress value appears in the connection between the center of the wheel and the spokes, and predict the fatigue life of the preliminary design of bionic wheel. Using finite element analysis and response surface optimization analysis method for numerical simulation, through two optimization results show that, in the use of response surface analysis model optimization, the optimized bionic wheel maximum stress is 109.34MPa, compared with the ordinary wheel maximum stress 119.77MPa, the maximum stress reduced by 8.7%. The mass of the ordinary wheel is 34.02Kg, using the response surface optimization method, the optimized wheel mass is 29.89Kg, the mass reduced by 12.13%. The optimized wheel fatigue analysis, in the stress of 109.34MPa, load loading times at least 4.217e+005, in the position at the junction with the half shaft. In line with the national standard GB/T 5334-2021[16] for commercial vehicle wheel fatigue life requirements.

In response to the structural optimization problem of PCB stator coreless disc motors, the orthogonal response surface method was used to optimize the motor structure, determine the basic parameters of the motor preliminarily, and conduct orthogonal experiments on the motor parameters based on the optimization design objectives, The optimization factors were the quantity of magnetic pole of the motor rotor, the ratio of main/auxiliary pole size, the thicknessof the permanent magnet, and the air gap length.The motor torque，the amplitude of magnetic density of the air gap and waveform distortion rateare used as optimization objectives. The motor parameters that make the motor torque reach the maximum, the air gap magnetic density maximum, and the waveform distortion rate minimum. Due to the use of PCB plates instead of motor stator cores in PCB coreless disc motors,The service life of the PCB board during motor operation will be reduced with the temperature rise generated by the stator winding To solve this problem, the response surface analysis of the motor is carried out to reduce the temperature rise of the stator windings during the operation of the motor. PCB board and stator winding are the main factors affecting the temperature rise of the motor.Taking the thickness of the PCB board, the hole diameter on the board, and the uneven width of the stator winding as optimization factors, the motor parameters with the lowest temperature rise of the motor winding are obtained. Simulation analysis is conducted using Ansys/Maxwell software, and the results prove the feasibility of optimization.

The present study employed a modifed QuEChERS method to systematically analyze the presence of fifteen Quinolones and seven Tetracyclines antibiotic residues in local animal food. Additionally, a multi-level-four-factor Box-Behnken design (BBD) within the framework of Response surface methodology (RSM) was utilized to evaluate the various factors affecting the detection efficiency of the sample pretreament procedure. The optimization was performed by Design Expert®, the factors including volume of the acetonitrle, the addition of formic acid, the duration of extract and the addition of EDTA were combined to experiment design until reach an optimal solution. Finally, the sample test was conducted by ultra-high performance liquid chromatography-quadrupole-linear ion trap mass spectrometry in both multiple reaction monitoring (MRM) and enhanced product ion (EPI) scan modes on a QTRAP® 5500 instrument. The overall average recoveries from actual samples fortified with 22 antibiotics at three levels ranged from 74.7 to 122.6% based on the use of matrix-fortified calibration with the variation ranging from 2.1 to 18.2% (n=6). The limits of detection and quantification were 0.3 μg kg-1 and 1.0 μg kg-1, respectively.

Multiphase systems are important in minerals processing, and usually include solid-solid and solid-fluid systems. Examples of operations in multiphase systems include flotation, dewatering, and magnetic separation, among several other unit operations. In this paper, the current trends in the process system engineering tasks of modeling, design, and optimization, in multiphase systems, are analyzed. Different scales of size and time are included, and therefore the analysis includes modeling at the molecular level and unit operation level, and the application of optimization for the design of a plant. New strategies for the modeling and optimization of multiphase systems are also included, with a strong focus on the application of artificial intelligence (AI) and the combination of experimentation and modeling with response surface methodology (RSM). The paper finishes with tools to study the uncertainty, both epistemic and stochastic, which is present in all mineral processing operations. It is shown that all these areas are very active and can help to understand, operate, design, and optimize mineral processing that involves multiphase systems.

The process of preparing anti-glare thin films by spray-coating silica sol-gel to soda-lime glass was exclusively and statistically studied in this paper. The effects of sol-gel deliver pressure, air transport pressure, and spray gun displacement speed on the gloss, haze, arithmetic mean surface roughness, and total transmittance light were analyzed. The experimental results indicate that the factors of sol-gel deliver pressure, air transport pressure, and displacement speed exhibit significant effect on the haze, gloss, and Ra. In contrast, the variation of total transmittance light with these three factors are insignificant. Because the anti-glare property is predominantly determined by low gloss and high haze, therefore, we aim to minimize gloss and maximize haze to achieve high anti-glare. Central composite design and response rurface methodology are employed to analyze the main and interaction effects of the three factors through quadratic polynomial equations, which are confirmed by the analysis of variance and R². The response surface methodology predict the lowest gloss and highest haze are 9.2 GU and 57.0%, corresponding to the sol-gel deliver pressure, air-transport pressure, and displacement speed of 250 kPa, 560 kPa, and 140 mm/s, and 340 kPa, 620 kPa, and 20 mm/s, respectively. Comparing the predicted optimal data with the real experimental results validates the applicability of the mathematical model. This study provides an important basis for the subsequent production of anti-glare glass with different specifications to satisfy the market demand.

Following legalization, cannabis has quickly become an important horticultural crop in Canada and increasingly so in other parts of the world. However, due to previous legal restrictions on cannabis research there are limited scientific data on the relationship between nitrogen (N), phosphorus (P), and potassium (K) supply (collectively: NPK) and the crop yield and quality. This study examined the response of a high delta-9-tetrahydrocannabinol (THC) Cannabis sativa cultivar grown in deep-water culture with different nutrient solution treatments varying in their concentrations (mg L^-1) of N (70, 120, 180, 250, 290), P (20, 40, 60, 80, 100) and K (60, 120, 200, 280, 340) according to a central composite design. Results demonstrated that inflorescence yield responded quadratically to N and P, with the optimal concentrations predicted to be 194 and 59 mg L^-1, respectively. Inflorescence yield did not respond to K in the tested range. These results can provide guidance to cultivators when formulating nutrient solutions for soilless cannabis production and demonstrates the utility of surface response design for efficient multi-nutrient optimization.

Friction stir welding (FSW) is a solid state welding process for joining metallic alloys and dissimilar metals. It has emerged as an alternative technology for welding high strength alloys that are difficult to join with conventional techniques. FSW is used to produce products with better mechanical properties. Now a days aluminum alloys have been widely used in several industrial applications such as aerospace, marine, automobile and commercial applications due to their light weight structure, better mechanical properties and high corrosion resistance.In this work, three welding parameters such as spindle speed, welding speed and plunge depth were considered for friction stir welding. FSW was carried out between dissimilar aluminum alloy plates (AA6061 and AA 8011) to produce butt joint.A Box-Behnken design with three factors and three levels was chosen to minimize the number of experimental conditions .The tensile strength and hardness of the welded regions were evaluated. The optimum level settings and the major parameters that influence the joint strength were obtained by Box-Behnken design.

This study was designed for the first time to improve phenolic yield and antioxidant activity of ultrasonic-assisted extraction from Acer truncatum leaves (ATL) using response surface methodology, and phenolic composition in ATL extracted under the optimized condition were characterized by UPLC-QTOF-MS/MS. Solvent and extraction time were selected based on preliminary experiments, and a four-factors-three-levels central composite design was conducted to optimize solvent concentration (X₁), material-to-liquid ratio (X₂), ultrasonic temperature (X₃) and power (X₄) for an optimal total phenol yield (Y₁) and DPPH• antioxidant activity (Y₂). The results showed that the optimal combination was ethanol: water (v:v) 66.21%, material-to-liquid ratio 1:15.31 g/mL, ultrasonic temperature 60 °C, power 267.30 W, and time 30 min with three extractions, giving a maximal total phenol yield of 7593.62 mg gallic acid equivalent /100 g d.w. and a maximal DPPH• antioxidant activity of 74241.61 μmol Trolox equivalent/100 g d.w.. Furthermore, 22 phenolics were first identified in ATL extract obtained under the optimized conditions, indicating that gallates, gallotannins, quercetin, myricetin and chlorogenic acid derivatives were the main phenolic composition in ATL. What’s more, a gallotannins pathway existing in ATL from gallic acid to penta-O-galloyl-glucoside was interpreted. All these results provided practical information aiming at full utilization of phenolics in ATL, together with fundamental knowledge for further research.

Abstract: With the continuous integration of various energy systems and the reform of energy trading marketization, the traditional power demand response can no longer meet the needs of multi-energy coupling. For the joint response problem of multi-energy, this paper proposes a comprehensive demand response optimization incentive model considering the user response characteristics, with the complete energy service providers and multiple users as the participants of the comprehensive demand response, to solve the response strategy for the optimal goal of all parties. The implementation architecture of integrated demand response and the electrothermal energy hub model is introduced first. Secondly, the integrated demand response collaborative optimization strategy of the integrated energy service providers and users is established, and the existence and uniqueness of the optimal solution are proved. Finally, the example analysis demonstrates that the proposed strategy can reduce the integrated energy service providers' response cost and user dissatisfaction under multiple scenarios.

RM (red mud) was acidified with sulphuric acid and the acidified ARM (acidified red mud) was utilized as an innovative adsorption material for treating antibiotic-contained wastewater. The adsorption conditions, kinetics, isotherms, thermodynamics, and mechanism of ARM for CIP (ciprofloxacin) were investigated. Characterization of the ARM involved techniques such as scanning electron microscopy(SEM), transmission electron microscope(TEM), brunauer- emmett-teller (BET), X-ray diffraction (XRD), X-ray fluorescence (XRF), thermogravimetric analysis (TGA) and NH3-TPD analysis. Adsorption studies were conducted employing response surface methodology (RSM) for experimental design. The results showed that ARM can absorb CIP effectively. The RSM optimal experiment indicated that the most significant model terms influencing adsorption capacity were solution pH, CIP initial concentration and ARM dosage, under which the predicted maximum adsorption capacity achieved 7.30 mg/g. The adsorption kinetics adhered to a pseudo-second-order model, while equilibrium data fitted the Langmuir-Freundlich isotherm, yielding maximum capacity values of 7.35 mg/g. The adsorption process occurred non-spontaneously and absorbed heat, evidenced by ΔG0 values between 2.06 and 0.87 kJ/mol, ΔS0 at 39.41 J/mol/K, and ΔH0 at 13.8 kJ/mol. Analysis using attenuated total reflection Fourier-transform infrared spectroscopy (ATR-FTIR) indicated there existed complex reaction between Al-O in ARM and the ester group –COO in CIP. The C=O bond in CIP was likely to undergo a slight electrostatic interaction or be bound to the internal spherical surface of ARM. The findings indicate that ARM is a promising and efficient adsorbent for CIP removal from wastewater.

Buckling defect will appear on the outer surface of the deformed ring during constrained ring rolling (CRR) of aluminum alloy thin wall conical ring with inner high ribs (AATWCRIHR), if the geometrical dimension of the ribs doesn't match the wall thickness. To avoid the buckling defect, a quantitative method for characterizing the degree of the buckling defect is proposed using the area of buckling profile. Then an orthogonal experimental scheme was designed taking the width of the middle rib, thickness of wall, and height of the middle rib as design variables and defining the area of buckling profile as optimization objective. Subsequently, a quadratic polynomial response surface model was established by combining the optimization algorithm with the finite element method (FEM), and the geometrical dimension of the middle ribs of the deformed AATWCRIHR is optimized. Also the optimal parameter combination to minimize the area of buckling profile is obtained and verified using FE simulation. Results show that the AATWCRIHR after optimization doesn’t generate the buckling defect during constrained ring rolling, and it is proved that the quantitative buckling defect representation method and the optimization design method based on the response surface model and the finite element simulation results are feasible for the constrained ring rolling process of the AATWCRIHR.

The present work aims at the comprehensive application of stochastic and optimization tools with the support of Information and Communication Technologies (ICT) through a case study in a logistics process for electronic goods; simulation and Response Surface Methodology (RSM) are applied for this purpose. The problem to be evaluated is to define an optimal distribution cost for products shipped to wholesale customers located in different cities in Mexico from a manufacturing plant in Tijuana, Mexico. The factors under study are the product allocation for each distribution center, finished good inventory level and on time deliveries, which are supposed to be significant to get the objective. The methodology applied for this problem considers the design of a discrete event simulation model to represent virtually the real life of logistics process, which is considered a complex system due to different activities are interrelated to carry it out. This model is used to execute the different experiments proposed by the RSM. The results obtained from simulation model were analyzed with the RSM to define the mathematical model that allows identifying the parameters of the factors in order to optimize the process. The findings prove how the ICT facilitate the application of stochastic tools with the purpose of process optimization.

A highly efficient reduction process of Cr (VI) with biochar was conducted in this paper. The results showed that nearly 100% Cr (VI) was reduced at selected reaction conditions: the dosage of biochar at m (C)/m(Cr) = 3.0, reaction temperature of 90 ℃, reaction time at 60 min and concentration of H2SO4 of 20 g/L, respectively. The reduction kinetics analysis demonstrated that the reduction of Cr (VI) fitted well with the pseudo-first-order model and the apparent activation energy was calculated to 40.24 kJ/mol. Response surface methodology confirmed that all the experimental parameters had positive effect on the reduction of Cr (VI). The influence of each parameter on the reduction process followed the order: dosage of biochar> Concentration of H2SO4 > Reaction Temperature > Reaction Time. This paper provided a versatile strategy for treatment of wastewater containing Cr (VI) and showed a bright tomorrow for wastewater treatment.

Using the above results from RMS analysis the optimum values were predicted for the independent significant variables (Figure 3) the optimized levels of these variables in combination with other media variables the maximum production was predicted to be 199.90 U/mL. The predicted data were validated through confirmatory experiments performed in triplicates. A 1.29-fold increase in amylase activity against un-optimized (OVAT) medium was achieved in the present study authenticating the efficacy of RSM in process optimization (Figure 4). 2.6 Model validation and scale-up at laboratory scale (5L) bioreactor Once the parameters were standardized in the shake-flasks culture, the experiment was scaled-up to a laboratory-scale bioreactor (5 L). The yield of amylase increased by 1.01 fold (205.69 U/mL), it could be possible because the enzyme production in a bioreactor is higher than in shake-flasks culture as the various critical variable factors such as the dissolved oxygen (DO) and the pH can be optimally controlled at the desired levels [22].

Green synthesis of silver nanoparticles (AgNPs) using raw Whey has never been reported. Silver nanoparticle formation involves a reduction reaction of silver salt solution with Whey extract. Extract and metal salt concentrations, and temperature can control this reaction. In this work, incubation period, extract, AgNO3, and NaOH concentrations were used as the independent factors using central composite design under response surface methodology. The aim was to elucidate the influence these factors have on the measured UV-Vis absorption spectra fitted with a Voigt function, and to optimize the conditions for nanoparticle formation. The fitting parameters, peak wavelength (λ0), peak area (A), and Full Width at Half Maximum (FWHM), were the responses. Silver nanoparticle formation was only possible in an alkaline environment (pH 10). The peak wavelength and the FWHM are influenced mainly by extract and AgNO3 concentrations. In contrast, the peak area is influenced by a total of 33.54 % from the interaction terms of AgNO3 and extract concentrations with NaOH. Metallic AgNPs were formed for the following parameter ranges: a) Whey (0.4 – 1.6 % v/v), b) AgNO3 (0.15 – 0.6 mM), c) NaOH (10 – 50 mM), and d) Time (20 – 60 min). Silver oxide nanoparticles were also observed.

The purpose of this article is to present an IoT architecture implemented in an intelligent environment, focusing on the optimization of initial conditions and device management. A general control system was developed using an open-source platform, integrating aWi-Fi network and YAML coding to enable communication and control of the IoT architecture devices. The implementation includes actuators, sensors, and control devices that, through a graphical interface, allow the visualization of the historical record of activities and real-time measurements of connected devices. The design includes specific mechanisms and the analysis of materials through tensile tests on specimens, following the ASTM E8 standard, and deformation test simulations, in which PLA demonstrated better performance compared to materials like ABS and resin. The significance of the implemented IoT system lies in an energy saving of 58% compared to conventional structures. Additionally, the study of response times for network connections showed that using an Ethernet cable resulted in a response time of 1.21 seconds, representing a reduction of 1.65 seconds compared to the second lowest value obtained.

Citrus peels are considered as a rich source of valuable biomolecules like pectin as polymer of polysaccharide acid. In this study, response surface methodology was used to optimize pectin extraction from Citrus clementina peels using citric acid as extraction solvent. The effect of parameters conditioning the extraction process and pectin yield (pH, temperature, extraction time, solid/liquid ratio, and raw material particle size) was investigated using a Box-Behnken design. The quality of the extracted pectin was assessed both chemically (moisture, ash, protein, and sugar content) and functionally (gelling power and emulsifying activity). According to the screening experiment, the factors pH, temperature, and particle size were the main factors influencing the pectin yield. The adjusted mathematical model enabled us to plot response surfaces in order to determine optimal extraction conditions. The highest production yield of pectin (26.6%) was obtained at the optimal conditions of: pH = 1.5; temperature 100 °C and particle size = 0.1 mm for an extraction time of 30min. Compared to the predicted value of 26.6%, the experimental extraction yield was about 21.4% of pectin. Concerning the functional properties, the extracted pectin has a high gelling power of 164°SAG and an emulsifying activity of 38.5%.

Breast cancer is the most common cancer in women globally, often necessitating mastectomy and subsequent breast reconstruction. Silicone mammary implants (SMIs) play a pivotal role in breast reconstruction, yet their interaction with the host immune system and microbiome remains poorly understood. This study investigates the impact of SMI surface topography on host antimicrobial responses, wound proteome dynamics, and microbial colonization. Biological samples were col-lected from ten human patients undergoing breast reconstruction with SMIs. Mass spectrometry profiles were analyzed for acute and chronic wound proteomes, revealing a nuanced interplay between topography and antimicrobial respondseproteins. 16S rRNA sequencing assessed mi-crobiome dynamics, unveiling topography-specific variations in microbial composition. Surface topography alterations influenced wound proteome composition. Microbiome analysis revealed heightened diversity around rougher SMIs, emphasizing topography-dependent microbial inva-sion. In vitro experiments confirmed staphylococcal adhesion, growth, and biofilm formation on SMI surfaces, with increased texture correlating positively with bacterial colonization. This comprehensive investigation highlights the intricate interplay between SMI topography, wound proteome dynamics, and microbial transmission. The findings contribute to understanding host-microbe interactions on SMI surfaces, essential for optimizing clinical applications and minimizing complications in breast reconstruction.

This paper presents a novel approach for individual design perception modeling using the YUKI-trained Fuzzy Inference System. The study focuses on understanding how individuals perceive design based on personality traits, particularly openness to experience. The proposed YUKI algorithm optimizes the FCM clustering algorithm, enhancing its ability to handle uncertain and imprecise data. The YUKI-trained FIS generates several Sugeno-type FIS models to predict design perception, to minimize the Root Mean Squared Error between the model prediction and the actual design perception of participants. The results demonstrate that the YUKI-trained FIS offers more accurate predictions compared to the traditional FCM-trained FIS, and the RMSE values for individual design perceptions fall within a satisfactory range of 0.84 to 1.32. The YUKI-trained FIS proves effective in clustering individuals based on their level of openness, providing insights into how personality traits influence design perception.

In this study, AlSi12 alloy was fabricated using the selective laser melting (SLM) technique to produce high density components with complex and customized parts for railway applications. Nonetheless, the production of dense samples necessitates the optimization of production process parameters. As a statistical design of experimental technique, the response surface methodology was used to optimise different combination of SLM parameters. The results were analysed using analyse of variance (ANOVA) and the signal-to-noise(S/N) ratios. The relationship between the hardness response to the process parameters (scanning speed and lase power) for determining the optimal processing conditions were examined. A hardness value of 133 HV was obtained. The process parameters were successfully optimized and the relationship between the parameters and the structures of the fabricated samples were reported.

This paper proposes the use of non-uniform extended surfaces installed externally to the tubes of the radiation section of fired heaters, in order to obtain a better heat flux distribution to the coils. To this end, the heat transfer mechanisms present in such equipment were studied through computational fluid dynamics (CFD), using simplified geometries that represent typical sizes of fired heaters. Also, a simplified model for the combustion was considered. Although this model oversimplifies the physics of the problem, it was able to give satisfactory results for the parameters being optimized, considering the main objective of this paper, that is to minimize the non-uniformity of heat flux in the tubes of the radiant section of fired heaters. It was possible to obtain optimized geometric parameters for different types of extended surfaces evaluated, coupling the results of these models with the Particle Swarm optimization method through the use of a response surface technique,. The results indicate a significant improvement in the uniformity of the heat flux distribution to the tubes through the use of the proposed extended surfaces. Thus, this solution reveals to be an interesting alternative to reduce the risks of fluid degradation and coking formation. Future studies must investigate the non-uniformity of the heat flux due to the presence of the flame and consider the interaction between the reactive flow and the participating medium. Nevertheless, this paper presents some results that justify the optimization of such extended surfaces taking into consideration thermal radiation.

To study the fermentation process of biocatalyzing decanoic acid to synthesize trans-2-decenoic acid, this study was based on the engineering E.coli constructed in the laboratory in the early stage and studied the effect of seed liquid culture time, culture temperature, inoculum amount, induction temperature, dissolution effects of substrate solvent, metal ions, and substrate loading on the yield of trans-2-decenoic acid. Based on single-factor experimental optimization, the Box–Behnken design was used to conduct response surface testing using the substrate feeding concentration, inducer concentration, and MnCl2 concentration as response variables and trans-2-decenoic acid production as the response value. The optimal fermentation process was determined through experiments: seed culture time 20 h, culture temperature 37°C, inoculation amount 1%, induction temperature 30°C, substrate flow amount 0.15 g/L, inducer concentration 5.60 g/L, MnCl2 concentration was 0.10 mM. Under these conditions, the average production of trans-2-decenoic acid was 1.982 ± 0.110 g/L. Compared with the basic LB medium, the production of trans-2-decenoic acid increased by 1.042 g/L; compared with the previous period, the yield of trans-2-decenoic acid studied increased by 1.501 ± 0.110 g/L, which provides a reliable basis for further research on the fermentation process of biocatalytic decanoic acid synthesis of trans-2-decenoic acid.

Chert rock is a by-product of sand quarrying (about 40% in the geological section). All attempts to use ordinary technologies for aggregate production from chert have been economically unsuccessful, resulting in significant chert "waste" accumulation covering vast quarry areas. This paper presents the study results of the effect of microwave irradiation on the mechanical properties of chert gravel, which is mineralogically relatively homogenous and consists of fine quartz grains. The results show that an increase in irradiation time decreases the strength of chert gravel (by a factor of 4-6 for the 2.5 min of irradiation), while the quenching changes the fractional content of the samples after the crushing test, decreasing the Gravel-to-Sand ratio.

Due to the non-degradability of petroleum-based packaging materials, serious environmental pollution and the depletion of non-renewable resources have become pressing issues. In order to actively promote green production and address these concerns, there is an urgent need for new packaging materials to replace traditional plastic products. Starch-based packaging materials, composed of starch, fiber, and plasticizers, offer a degradable and environmentally friendly alternative. Starch alone cannot undergo thermoplastic processing due to its inherent structural characteristics. Therefore, researchers have explored modifications by incorporating plasticizers to create processable thermoplastic starch (TPS). However, there are challenges related to the high crystallinity and poor compatibility between TPS and fibers, resulting in decreased mechanical properties. To address these challenges, a novel approach combining plasticizer optimization and response surface method (RSM) optimization has been proposed to enhance the mechanical properties of starch-based packaging materials. This method leverages the advantages of composite plasticizers and process parameters. The findings demonstrate that the composite plasticizer effectively disrupt the hydrogen bonding and granule morphology of starch, leading to a significant reduction in crystallinity. Based on these findings, the optimal process parameters are determined using the RSM, resulting in a forming temperature of 198 °C, forming time of 5.4 minutes, and AC content of 0.84 grams. Compared with the non-optimized values, the tensile strength increases by 12.2% and the rebound rate increases by 8.1%.

An ion exchange dialysis (IED) is used in the recovery of aluminium from residue. In this papers, the face-centered central composite design (FC-CCD) of the response surface methodology (RSM) and desirability approach is used for experimental design, modelling and process optimization of a counter flow IED system. The feed concentration, feed flowrate, sweep flowrate and sweep concentration are selected as the process variables, with the Al-transport across a Nafion 117 membrane as the target response. A total of 30 experimental runs were conducted with 6 center points. The response obtained was analysed by analysis of variance (ANOVA) and fitted to a second-order polynomial model using multiple regression analysis. The actual R2 and standard deviation of the model are 0.9548 and 0.2932 respectively. The influences of significant variables are plotted on 3D surface and contour plots. The designed variables were numerically optimized by applying the desirability function to achieve the maximum Al-transport. The optimised condition values were found to be feed concentration (1600 ppm), feed flowrate (61.76%), sweep flowrate (37.50%) and sweep concentration (0.75 N) for the 80% target response at 32hrs. Overall, the model can be used to effectively predict Al-recovery using the designed system

Lactoperoxidase (LP), which is a high-value minor whey protein, has recently drawn extensive attention from research scientists and industry due to its multi-function and potential therapeutic applications. In this study, the separation and optimization of two similar-sized proteins, LP and lactoferrin (LF) were investigated using strong cation exchange column chromatography. Optimization was started with central composite design based experiments to characterize the importance of different decision variables. The three variables used in the optimization were flow rate, length of gradient and final salt concentration in the linear elution gradient step. The obtained empiric functional model represented the effect of the significant factors on the yield as the objective function. Afterwards, the calibrated mechanistic model was employed to predict accurate optimal set of variables. The optimal operating points were found and the results were compared with validation experiments. Predictions respecting yield confirmed a very good agreement with experimental results while keeping purity, a product quality characteristic, equal or above to a predefined value.

In order to improve the yield of the therapeutic agent N-methylsansalvamide (SA), optimization of stationary liquid fermentation conditions was carried out on an endophytic strain, Fusarium sp. R1, at flask level. Using a One-Factor-At-a-Time approach, the fermentation conditions for SA production were determined as follows: fermentation time of 13 d, 24 oC, initial pH of 6.5, seed age of 24 h, inoculum size of 5.0% (v/v), loading volume of 50% (v/v), 20.0 g/L salinity, and sucrose, tryptone, and yeast extract were found to be the best sources of carbon and nitrogen. Using response surface methodology, the optimal medium compositions consist of 22.5 g/L sucrose, 16.5 g/L tryptone, and 0.024 g/L yeast extract. Verification tests suggested that the SA yield under these optimal conditions reached up to 536.77 ± 2.67 mg/L, which was increased by almost ten times the initial yield (54.05 ± 3.45 mg/L). The findings indicate that a high SA production yield can be achieved by static culture of strain R1 under the proper fermentation conditions using a low-cost medium. This study paves the way towards industrial-scale SA production by strain R1 for new drug development.

The link between the world of communication and the world of racing is provided by telemetry systems in electric racing cars. These systems send real-time data about the vehicle’s behavior and systems to enable informed decisions during the race. The aim of this research was to integrate telemetry into the battery bank of a racing electric vehicle to find the optimal values of current and voltage that optimize the charging process, thus improving the vehicle’s performance in competition using Response Surface Analysis. Particularly, the telemetry system consisted of an Arduino Mega, a digital wattmeter, and temperature sensors, all installed in the vehicle. Once the telemetry data was obtained, a response surface design was adapted with current, voltage, and temperature as factors, varying from low to high values, with the objective function being to minimize the battery’s charging time. Applying the response surface methodology and the steepest descent algorithm, it was found that all factors significantly affect the charging time, with the minimum charge time being 6961 seconds, obtained with a current of 2.4 amps and voltages of 50.5 volts and 43.6 volts.

The advancement of technology and the availability of specialized digital signal processing chips have made digital filter design and implementation more feasible in a variety of fields, including biomedical engineering. This paper makes two key contributions. First, it uses a genetic algorithm to optimize the coefficients of Finite Impulse Response (FIR) filters. Second, it conducts a case study on using genetic algorithms to optimize FIR filters for electrocardiogram (ECG) biomedical signal noise removal. The goal of the proposed filter design approach is to achieve the desired signal bandwidth while minimizing the side lobe level and eliminating unwanted signals using a genetic algorithm. The results of the comprehensive analysis of the impact of different genetic operators show that the genetic algorithm-based filter outperforms conventional filter designs.

In this study, we applied a central composite design to estimate independent variables and establish optimal conditions of filtration rate and feces production that enhance filtration of suspended organic matter by the freshwater mussels Sinanodonta woodiana. The results indicated that statistical design methodology offers an efficient and feasible approach for high filtration and low feces production condition optimization. The proposed model equation takes into account the quantitative effect of variables and also the influence of interactions among variables on mussel filtration rate. Under the optimal experimental conditions (mussel size, 13.0 ± 0.2 cm; water current, 17.5 L/h), the experimental filtration rate of 4.47 ± 1.82 L/mussel/h showed a degree of correspondence with the predicted value of 8.4 L/mussel/h, which verified the practicability of this optimum strategy.

Influenza virus infection causes severe respiratory illness in people worldwide, disproportionately affecting infants. The immature respiratory tract coupled with the developing immune system is thought to synergistically play a role in the increased disease severity in younger age groups. Although vaccines remain the best solution for protecting this vulnerable population, no vaccines are available for those under 6 months, and for infants aged 6 months to 2 years, the vaccine elicits a dampened immune response. Dampened immune responses may be due to unique features of the infant immune system and a lack of pre-existing immunity. Unlike older children and adults, the infant immune system is Th2 skewed and has less antigen presenting cells and soluble immune factors. Paradoxically, we know that a person’s first infection with the influenza virus during infancy or childhood leads to the establishment of life-long immunity toward that particular virus strain. This is called influenza imprinting. To provide better protection against influenza virus infection and disease in infants, more research must be conducted to understand the imprinting event. We contend that by understanding influenza imprinting in the context of the infant immune system and the infant’s immature respiratory tract, we will be able to design more effective influenza vaccines for both infants and adults. Working through the lens of imprinting, using infant influenza animal models such as mice and ferrets, which have proven useful for infant immunity studies, we will gain a better understanding of imprinting and its implications regarding vaccine design. This review examines literature regarding infant immune development, current vaccine strategies, respiratory development, and the importance of researching the imprinting event in infant animal models to develop more effective and protective vaccines for young children.

Geopolymer cement has been popularly studied nowadays compared to ordinary Portland cement because it demonstrated superior environmental advantages due to its lower carbon emissions and waste material utilization. This paper focuses on the formulation of geopolymer cement from nickel-laterite mine waste (NMW) and coal fly ash (CFA) as geopolymer precursors, and sodium hydroxide (SH) and sodium silicate (SS) as alkali activators. Different mix formulations of raw materials are synthesized to produce a geopolymer based from an I-optimal design and obtained different compressive strengths. A mixed formulation of 50% NMW and 50% CFA, SH-to-SS ratio of 0.5, and an activator-to-precursor ratio of 0.429 yielded the highest 28-day unconfined compressive strength (UCS) of 22.10 ± 5.40 MPa. Furthermore, using an optimized formulation of 50.12% NMW, SH-to-SS ratio of 0.516, and an activator-to-precursor ratio of 0.428, a UCS value of 36.30 ± 3.60 MPa was obtained. The result implies that the synthesized geopolymer material can be potentially used for concrete structures and pavers, pedestrian pavers, light traffic pavers, and plain concrete.

Automated controlling the harvesting systems can significantly increase the efficiency of the agricultural practices and prevent food wastes. Modeling and improvement of the combine harvester can increase the overall performance. Machine learning methods provide the opportunity of advanced modeling for accurate prediction of the highest performance of the machine. In this study, the modeling of combine harvesting id performed using radial basis function (RBF) and the hybrid machine learning method of adaptive neuro-fuzzy inference system (ANFIS) to predict various variables of the combine harvester for the optimal performance. Response surface methodology (RSM) is also used to optimize the models. The comparative study shows that the ANFIS method outperforms the RBF method.

Continuous rigid frame bridges across valleys are often at the risk of rockfalls caused by heavy rainfalls, earthquakes and debris flows in a mountainous country. Hollow thin-walled bridge piers (HTWBP) in valleys are exposed to the threat of the impact of accidental rockfalls. In the current research, ANSYS/LS-DYNA is used to establish a high-precision rockfall-HTWBP model. The rockfall-HTWBP model is verified against a scaled impact test of a previous research. A mesh independence test is also performed to obtained an appropriate mesh size. Based on the rockfall-HTWBP model, the impact force, damage and dynamic response characteristics of HTWBP under the rockfall impact are studied. In addition, a damage assessment criteria is proposed based on the response surface model combined with Central Composite Design method and Box-Behnken Design method. The main conclusions are as follows: 1）The impact force of rockfall has a substantial impulse characteristic, and the duration of the impulse load is approximately 0.01s. 2）The impacted surface of the pier is dominated by the final elliptic damage with the conical and strip damage areas as the symmetry axis. The cross-sectional damage mode is compression failure in the impact area and shear failure at the corner. 3）The maximum displacement occurs in the middle height of the pier. The maximum displacement increases with impact height, impact velocity and rockfall diameter and decreases with the uniaxial compressive strength of the concrete. 4) The initial impact velocity and diameter of the rockfall are the most significant parameters affecting the damage indices. In addition, a damage assessment method with a damage zoning diagram based on the response surface method is established for the fast assessment of the damage level of impacted HTWBP.

In this study, the efficiency of an anaerobic treatment system for wastewater from a South African poultry slaughterhouse was evaluated using a lab-scale static granular bed reactor (SGBR). The down-flow SGBR (2 L) was operated continuously for 138 days under mesophilic conditions (35-37 ˚C), at hydraulic retention times (HRTs) ranging from 24 to 96 h and average organic loading rates (OLRs) of 0.78 to 5.74 g COD/L.day. The SGBR achieved an average chemical oxygen demand (COD) removal efficiency of 80% and the maximum COD removal achieved was 95%, at an HRT of 24 h and average OLR of 5.74 g COD/L.day. The optimization of the SGBR, with regard to a suitable HRT and OLR, was determined using response surface methodology (RSM). The optimal SGBR performance with regard to the maximum COD removal efficiency was predicted for an OLR of 12.49 g COD/L.day and a HRT of 24 h, resulting in a 95.5% COD removal efficiency. The model R2 of 0.9638 indicated that the model is a good fit and is suitable to predict the COD removal efficiency for the SGBR.

In this study, a novel and efficient method was developed for the extraction of total flavonoids from Flos Sophorae Immaturus (FSI) using ultrasound-assisted deep eutectic solvent (UAE-DES). Different DES formulations were first investigated and choline chloride/1,2-propanediol (ChCl/PD) was identified as the optimal solvent due to its highest flavonoid yield. The extraction process was optimized through single factor experiments and response surface methodology (RSM). An extraction temperature of 68 °C, a sonication time of 41 minutes, a water content of 21% and a liquid-solid ratio of 21 mL/g were identified as the optimal conditions. Under these conditions, a maximum flavonoid yield of 378.77 mg RE/g DW was achieved. The crude extract was further purified using a macroporous D-101 resin, resulting in a flavonoid extract with a purity of 83.11 ± 3.54%. The antioxidant activity of the purified extract (FSPE) was evaluated using DPPH and ABTS radical scavenging assays, showing significant antioxidant properties with IC50 values of 52.50 μg/mL and 49.47 μg/mL, respectively. The UAE-DES method developed in this study not only significantly improves the extraction yield of flavonoids from FSI, but is also in line with sustainable and environmentally friendly practices. This method offers an environmentally friendly, efficient and scalable approach for the extraction of bioactive compounds from medicinal plants and has potential applications in the food, pharmaceutical and dietary supplement industries.

Traditional potential transformers have problems of large volume, difficulty in insulation, iron core saturation, ferroresonance overvoltage and poor transient response characteristics. The voltage sensor based on the principle of electric field coupling and differential input structure does not need to contact the measured object or ground, and can avoid the above problems. However, it requires a sufficiently high capacitance between the differential electrodes to obtain sufficient accuracy and a high voltage division ratio. The existing method of using mutual capacitance between the differential electrodes will cause many problems and fail to meet the practical needs. To solve the above problems, this paper innovatively uses multi-layer ceramic capacitor to replace the mutual capacitance and designs a new type of voltage sensor. In addition, by using single bypass small resistance grounding method to increase the input impedance of the differential signal processing circuit, error of the sensor is further reduced. The experimental results show that the sensor has excellent accuracy and great transient response characteristics. The ratio error under power frequency is within ±0.5% and the phase error is within 1. The ratio error in the range of 500 Hz∼30 kHz is within ±5% and the phase error is within 5. Moreover, it has the advantages of low cost, miniaturization, flexible shape and easy to adjust the voltage division ratio. These characteristics indicate that the sensor has good voltage measurement and sensor network potential.

Efficient utilization of biomass requires conversion into forms that can be optimally applied in energy generation. Briquetting involves compaction of biomass into solid blocks that are more efficient than raw biomass and provides for ease of transport and handling. These are improved when the briquettes possess high shatter index and compressive strength. Due to difference in nature and composition, it is imperative to define optimum conditions for the production of quality and durable briquettes for individual biomass compacted into briquettes. This study studied the effects of process variables on the strength and durability of biomass briquettes produced using Abura sawdust. The lateral compressive strength and drop shatter index were investigated whilst varying the temperature (100-150 °C), pressure (9-15 MPa) and hold time (15-30 min). The compressive strength ranged between 2.06 and 5.15 MPa whilst the shatter index was between 50 and 600. The pressure was significant to the determination of the compressive strength (p < 0.1) and the shatter index (p < 0.05). Mechanical characteristics of the binderless Abura sawdust briquettes can be improved by optimizing the densification variables during the briquetting process when moderate pressures are used for compaction.

Under high-frequency operating conditions, the high-speed solenoid valve (HSV) experiences energy loss and heat generation, which significantly impact its operational lifetime. Reducing the energy loss of HSV without compromising its opening response characteristics poses a significant challenge. To address this issue, a finite element simulation model of HSV coupled with a current feedback model is constructed to investigate the synergistic effects of dynamic response and energy loss. Predictive models for the opening response time, HSV driving energy, and Joule energy using Back Propagation neural network (BPNN) are established. Furthermore, a multi-objective optimization study on the current driving strategy using Non-dominated Sorting Genetic Algorithm II (NSGA-II) is conducted. After optimization, although there was a 6.24% increase in the opening response time, both HSV drive energy and Joule energy were significantly reduced by 15.67% and 22.49%, respectively. The proposed multi-objective optimization method for HSV driving strategy holds great significance in improving its working durability.

To satisfy the interests of multiple agents and those of comprehensive indicators such as peak-to-valley differences and load fluctuations occurring on the network side, this paper presents a flexible load demand-side response optimization method that considers the benefits of peak-to-valley smoothing. First, load aggregation modelling of air conditioning and electric vehicles was conducted, and the complementarity of the power consumption behaviour of different types of flexible loads was used to improve the responsiveness of the load aggregator. Second, considering demand-side responses and taking into account the interests of both supply and demand, the load fluctuation and peak-to-valley difference on the network side are reduced, and a flexible load double-layer optimization model incorporating the peak-to-valley smoothing benefit is established. Finally, the effectiveness of the proposed optimization model is verified by using the KKT condition and the big M method to evaluate this two-layer optimization problem as a single-layer optimization problem. Comparative examples demonstrate that the proposed two-layer optimization method can improve the revenue of the distribution network operators and the load aggregators by using the complementary nature of the load response characteristics of electric vehicles and air conditioners. Moreover, the proposed method can effectively reduce the load peak-to-valley difference and load fluctuation of the distribution network by introducing the peak-to-valley smoothing benefit model.

Demand response flexible loads can provide fast regulation and ancillary services as reserve capacity in power systems. This paper proposes a joint optimization dispatch control strategy for source-load system with stochastic renewable power injection and flexible thermostatically controlled loads (TCLs) and plug-in electric vehicles (PEVs). Specifically, the optimization model is characterized by a chance constraint look-ahead programming to maximal the social welfare of both units and load agents. By solving the chance constraint optimization with sample average approximation (SAA) method, the optimal power scheduling for units and TCL/PEV agents can be obtained. Secondly, two demand response control algorithms for TCLs and PEVs are proposed respectively based on the aggregate control models of the load agents. The TCLs are controlled by its temperature setpoints and PEVs are controlled by its charging power such that the DR control objective can be fulfilled. The effectiveness of the proposed dispatch and control algorithm has been demonstrated by the simulation studies on a modified IEEE 39 bus system with a wind farm, a photovoltaic power station, two TCL agents and two PEV agents.

Mammalian species possess sophisticated innate immune mechanisms that collectively combat a wide array of viral pathogens. Among these, the well-characterized interferon (IFN) response has been extensively researched; however, the role of antiviral RNA interference (RNAi) in mammals is emerging as an area of significant interest. Previous research has noted that Dicer, an enzyme crucial for processing double-stranded RNA (dsRNA), exhibits reduced activity in vitro, and that the IFN response may overshadow or inhibit the antiviral functions of RNAi in mammalian cells. Consequently, the functional relevance of RNAi in antiviral defense within mammalian somatic cells remains an open question. The evolution of antiviral systems in human populations reflects their substantial advantages, paralleling the evolutionary pressure on genomes encoding such defense mechanisms. While the well-studied protein-guided immune responses in mammals are essential for survival in viral environments, small RNA-mediated antiviral systems, which utilize complementary base pairing to silence non self-genetic material, also play a crucial role. In mammals, evidence suggests that microRNAs (miRNAs) regulate genes integral to antiviral responses, and emerging data indicate that small interfering RNAs (siRNAs), PIWI-interacting RNAs (piRNAs), and transfer RNAs (tRNAs) can directly target virus-derived nucleic acids. This review aims to highlight some of the recent progress in understanding mammalian antiviral RNAi mechanisms.

In this study, the optimal condition for the extraction of antioxidants from the fruit Buah Mahkota Dewa (Phaleria macrocarpa) was determined by using Response Surface Methodology (RSM). The optimization was applied using central composite design (CCD) to investigate the three independent variables, namely extraction temperature (^oC), extraction time (minutes) and extraction solvent to-feed ratio (%v/v) on the responses of free radical scavenging activity (DPPH), ferric ion reducing power assay (FRAP), total phenolic content (TPC) and total flavonoid content (TFC).The optimal conditions for the antioxidants extraction were found to be extraction temperature (64^oC), extraction time (66 minutes) and solvent to-feed ratio (75 %v/v) with the highest percentage yield of DPPH, FRAP, TPC and TFC were 86.85%, 7.47%, 292.86 mg/g and 3.22 mg/g respectively. Moreover, the data were subjected to response surface methodology (RSM) and the results showed that the polynomial equations for all models were significant, did not show lack of fit, and presented adjusted determination coefficients (R²) above 99%, proving the yield of phenolic, flavonoid and antioxidants activities obtained experimentally were close to the predicted values and the suitability of the model employed in RSM to optimize the extraction conditions. Hence, in this study, the fruit from P.macrocarpa could be considered to have the strong antioxidant ability and can be used in various cosmeceutical or medicinal applications.

Dietary polyphenols exist in two forms; extractable polyphenols (EPP) or compounds solubilised by aqueous/organic solvents, and non-extractable polyphenols (NEPP) or compounds remain in the corresponding residues after the extraction. At present, most researchers focus on EEP fractions, while NEPP is neglected. Thus, this study aimed to release NEPP from the remaining powder residue of Barhi date palm kernels (BDPK) with acid hydrolysis. The related extraction conditions were determined and optimised using response surface methodology (RSM) for maximisation of NEPP with highest cytotoxic and antioxidant activities. The face-centred central composite design (FCCCD) was used to establish treatments based on three independent variables, namely; extraction temperature, time, and solvent/sample ratio. Under the optimal conditions, the experimental values for DPPH radical-scavenging capacity of NEPP (IC50=57.52µg/mL), and cytotoxicity of NEPP against A549 and HT29 cells were IC50=17.4 µg/mL and 31.4µg/mL, respectively. The experimental values were in agreement with those predicted by RSM models, confirming the suitability of the model employed and the success of RSM for optimisation of the extraction conditions for NEPP from BDPK. These results indicate that NEPP from industrial date fruit waste could be a promising candidate as natural antioxidants with significant antiproliferation effect against A549 and HT29 cancer cells in-vitro.

The study presents a comparative approach between response surface methodology (RSM) and hybridized, genetic algorithm artificial neural network (GA-ANN) in predicting the water absorption, compressive strength, flexural strength split tensile strength and slump for steel fiber reinforced concrete. The effect of process variables such as aspect ratio, water cement ratio and cement content were investigated using the central composite design of response surface methodology. This same experimental design was used in training the hybrid-training approach of artificial neural network. The predicting ability of both methodologies were compared using the root mean sqaured error (RMSE), mean absolute error (MAE), model predictive error (MPE) and absolute average deviation (AAD). The RSM model was found more accurate in prediction compared to hybrid GA-ANN.

Social surveys are conducted to determine how annoyed people are in a certain noise situation. The results are typically presented as exposure-response curves showing the percentage of the area population that are highly annoyed as a function of the noise exposure level. It is a well-known fact that the survey results are not only dependent on the accumulated noise exposure, DNL, DENL, or similar, but also on various other factors such as maximum levels, exposure patterns, noise spectra, etc. A re-analysis of previously reported surveys shows that the results are also to a large extent dependent on survey-specific factors like wording of the annoyance questions, how the questionnaires are presented, response scales, methods of scoring highly annoyed, etc. This paper discusses and quantifies the influence of such factors and suggests ways of comparing results from surveys that have been conducted according to different protocols and different analysis methods.

A novel approach based on response surface methodology (RSM) was developed to predict and apply the best extraction conditions for the isolation of various-type polyphenolic antioxidants from the dried flower buds of Magnolia x soulangeana Soul.-Bod. var. ‘Lennei’ (Magnoliaceae). As a method of choice, ultrasound-assisted extraction was used and the optimized extraction parameters (temperature, time of extraction, the composition of aqueous-ethanolic extractants and solvent to solid ratio) have been determined using a central composite design factorial analysis, followed by appropriate spectrophotometric methods (with Folin–Ciocalteu and 2,2-diphenyl-1-picrylhydrazyl reagents) to determine the antioxidant and antiradical potential of extracts, respectively. The use of 66.8% (V/V) ethanol, as the extraction solvent during the 55.2 min extraction protocol, and the ratio of extractant volume to herbal substance of 46.8 mL/g gave the highest total yield of bioactive antioxidant phenolics in the extract obtained. For this herbal preparation, qualitative and quantitative analysis was performed using combined chromatographic (LC), spectroscopic (PDA) and tandem mass spectrometric (ESI-QTOF–MS/MS) techniques. A detailed phytochemical profiling, conducted for the first time, documented substantial amounts of polyphenolic antioxidants, especially phenylethanoids and flavonoids in the flower buds of M. soulangeana ‘Lennei’. Their average total content exceeded 30.3 and 36.5 mg/g dry weight, respectively.

Following technological advances, autonomous and remote-controlled ships are performing trials in some sea areas; a mandatory goal-based MASS code, expected to enter into force on 1 January 2032, is under discussion in the International Maritime Organization (IMO). However, there are no unified standards regarding verification methods to define operating limitations for cutting-edge technologies, which are expected to be elements of MASS, so it is difficult to assess the risk factors for the management and operation of MASS. This paper outlines the regulatory framework for MASS, followed by a discussion of its application, considering the differences between MASS and automated driving, and how to develop safety management and operation using standards for automated driving. A requirements management framework developed as a system and software engineering standards to build safety management and operation of MASS is proposed. It is also suggested that the requirements management framework could be used not only for MASS development but also for regulatory review from a requirements management view.

Hemifacial spasm (HFS) is a rare disorder characterized by involuntary facial muscle contractions. The primary cause is mechanical compression of the facial nerve by nearby structures. Lateral spread response (LSR) is an abnormal muscle response observed during electromyogram (EMG) testing and is associated with HFS. Intraoperative monitoring of LSR is crucial during surgery to confirm successful decompression. Proper anesthesia and electrode positioning are important for accurate LSR monitoring. Stimulation parameters should be carefully adjusted to avoid artifacts. The disappearance of LSR during surgery is associated with short-term outcomes, but its persistence does not necessarily indicate poor long-term outcomes. LSR monitoring has both positive and negative prognostic value, and its predictive ability varies across studies. Early disappearance of LSR can occur before decompression and may indicate better clinical outcomes. Further research is needed to fully understand the implications of LSR monitoring in HFS surgery.

This letter introduces a frequency response characteristic (FRC) curve and its application in high renewable power systems. In addition, the letter presents a method for fast frequency response assessment and frequency nadir prediction without performing dynamic simulations using detailed models. The proposed FRC curve and fast frequency response assessment method are useful for operators to understand frequency response performance of high renewable systems in real time.

The integrated stress response (ISR) is an adaptational signaling pathway that is induced in response to different stimuli, such as accumulation of unfolded and misfolded protein, hypoxia, amino acid deprivation, viral infection and ultraviolet light. It has been known that viral infection can activate ISR, but the role of ISR during viral infection is still unclear. In some cases, ISR is a protective mechanism of host cell against infection with virus whilst ISR may be hijacked by viruses for facilitating its replication. In this review, we highlighted recent advances on induction of ISR upon viral infection and the downstream responses involved such as autophagy, apoptosis, formation of stress granules and innate immunity response. We then discussed the molecular mechanism of ISR regulating viral replication and how viruses antagonize this cellular stress response resulting from ISR.

Photosynthetic activities of the sago palm (Metroxylon sagu Rottb.) were studied to find out its sensitivity to changes in ambient air temperature. The minimum ambient air temperature designed for the experiment was 25–29⁰C, while the higher end was 29–33⁰C. Several photosynthetic parameters were studied to support our analysis in sago photosynthetic activity, including diurnal leaf gas exchange, assimilation rate vs. CO₂ concentration, leaf greenness, leaf chlorophyll content, and photosynthetic rate vs. irradiance. We found that sago palm photosynthetic activity tends to be more sensitive to minimum than to maximum ambient air temperature. The plants exposed to higher air temperatures had dark green leaf color associated with higher rates of diurnal photosynthesis, chlorophyll content, and rubisco limited photosynthetic activity. They also exhibited higher trend in optimum irradiance absorption level. Consequently, maximum light energy dissipation occurred at higher temperatures.

The successful vaccination implies the induction of effective specific immune responses. We intend to find biomarkers among various immune cell subpopulations, cytokines and antibodies which could be used to predict the levels of specific antibody- and cell-mediated responses after measles-mumps-rubella vaccination. We measured 59 baseline immune status parameters (frequencies of 42 immune cell subsets, levels of 13 cytokines, immunoglobulins) before vaccination and 13 response variables (specific IgA and IgG, antigen-induced IFN-γ production, CD107a expression on CD8+ T lymphocytes, and cellular proliferation levels by CFSE dilution) 6 weeks after vaccination for 19 individuals. Statistically significant Spearman correlations between some baseline parameters and response variables were found for each response variable (p<0.05). Due to the low number of observations relative to the number of baseline parameters and missing data for some observations, we utilized three feature selection strategies to select potential predictors of the post-vaccination responses among baseline variables: (a) screening of the variables based on the correlation analysis, (b) supervised screening based on the information of changes of baseline variables at day 7, (c) implicit feature selection is performed using regularization-based sparse regression. We identified optimal multivariate liner regression models for predicting the effectiveness of vaccination against measles-mumps-rubella using the baseline immune status parameters. It turned out that the sufficient number of predictor variables ranges from one to five depending on the response variable of interest.

Background and introduction: Lung cancer is a prevalent and deadly disease globally. Non-small cell lung cancer (NSCLC) is the most common subtype, comprising 85% of cases; Case report: A 65-year-old ex-smoker man presented to our facility with nocturnal cough. Various investigations revealed that he had metastatic NSCLC, for which he underwent chemotherapy with cisplatin and gemcitabine, followed by immunotherapy with Nivolumab. He achieved a complete response to the therapy and has remained free from recurrence for over 7 years since the initial diagnosis; Discussion and Conclusion: The treatment of metastatic NSCLC remains a significant therapeutic challenge, but the implementation of new therapeutic techniques has expanded the possibilities of achieving complete and durable eradication of the disease.

Cucumber (Cucumis sativus L.) is a vital economic vegetable crop, and TRM (TONNEAU1 Recruiting Motif) gene plays a key role in cucumber organ growth. However, the pan-genomic characteristics of the TRM gene family and their expression patterns under different stresses have not been reported in cucumber. In this study, we identified 29 CsTRMs from the pan-genomes of 13 cucumber accessions, with CsTRM29 existing only in PI183967. Most CsTRM proteins exhibited differences in sequence length, except five CsTRMs having consistent protein sequence lengths among the 13 accessions. All CsTRM proteins showed amino acid variations. Analysis of CsTRM gene expression patterns revealed that six CsTRM genes strongly changed in short-fruited lines compared with long-fruited lines. And four CsTRM genes strongly responded to salt and heat stress, while CsTRM14 showed responses to salt stress, powdery mildew, gray mold and downy mildew. Some CsTRM genes were induced or suppressed at different treatment timepoint, suggesting that cucumber TRM genes may play different roles in responses to different stresses, with expression patterns varying with stress changes. Remarkably, the expression of CsTRM21 showed considerable change between long and short fruit and in responses to abiotic stresses (salt stress, heat stress) as well as biotic stresses (powdery mildew, gray mold), suggesting a dual role of CsTRM21 in both fruit shape determination and stress resistance. Collectively, this study provided a base for further functional identification of CsTRM genes in cucumber plant growth and stress resistance.

During the SARS-CoV-2 vaccination campaign, people with CF (pwCF) were considered a clinically vulnerable population. However, data on immunogenicity of anti-SARS-CoV-2 vaccines in pwCF are lacking. We conducted a prospective study enrolling all patients aged >12 and followed-up in our CF centre, who received two doses of the BNT162b2 vaccine in March-­­­October 2021. They underwent a blood sample for quantification of antibodies to the SARS-CoV-2 spike protein receptor binding domain immediately before receiving the first dose and after 3 and 6 months from the second dose. We enrolled 143 patients (median age: 21 years, range: 13-38); of whom 16 had a previous infection. Median antibody titer (interquartile range) after 3 months from vaccination was 1288 U/mL (730-2115) and decreased to 918 U/mL (534-1488) after 6 months (P<0.0001). Median values were higher among previously infected patients as compared to those naïve to SARS-CoV-2 (9107 vs 1229 U/mL at 3 months and 4810 vs 829 U/mL at 6 months, P<0.0001) with no significant differences in the rate of decline over time (P=0.135). All pwCF mounted an antibody response after two-doses of BNT162b2 vaccine that waned at 6 months from vaccination. Age ≥30 years and use of inhaled corticosteroids were associated with a lower humoral response.

Conformal radiotherapy is a primary treatment in head and neck cancer, which putative adverse effects depend on relatively low doses of radiation delivered to increased volumes of normal tissues. Systemic effects of such treatment include radiation-induced changes in serum lipid profile, yet dose- and volume-dependence of these changes remain to be established. Here we analyzed levels of choline-containing phospholipids in serum samples collected consecutively during the radiotherapy used as the only treatment modality. The LC-MS approach applied in the study enabled the detection and quantitation of 151 phospholipids, including (lyso)phosphatidylcholines and sphingomyelins. No statistically significant differences were found in the pre-treatment samples from patients with different location and stage of cancer. To compensate for potential differences between schemes of radiotherapy the biologically effective doses were calculated and used in the search of correlations with specific lipid levels. We found that the levels of several phospholipids depended on the maximum dose delivered to the gross tumor volume and total radiation energy absorbed by the patient’s body. Increased doses correlated with increased levels of sphingomyelins and reduced levels of phosphatidylcholines. Noteworthy, serum phospholipid levels were associated mainly with volumes of normal tissues irradiated with relatively low doses (i.e., total accumulated dose 20 Gy), which indicated the importance of such effects on the systemic response of the patient’s organism to IMRT.

Production of biofuel from lignocellulosic biomass is relatively low due to the limited knowledge about natural cell wall loosening and cellulolytic processes in plants. Industrial separation of cellulose fiber mass from lignin, its saccharification and alcoholic fermentation is still cost-ineffective and environmental unfriendly. Assuming that the green transformation is inevitable and that the new sources of raw materials for biofuels are needed, we decided to study cell death - a natural process occurring in plants in a context of reducing the recalcitrance of lignocellulose for production of second generation bioethanol. “members of the enzyme families responsible for lysigenous aerenchyma formation were identified during the root hypoxia stress in Arabidopsis thaliana cell death mutants. The cell death regulatory genes, LESION SIMULATING DISEASE 1 (LSD1), PHYTOALEXIN DEFICIENT 4 (PAD4) and ENHANCED DISEASE SUSCEPTIBILITY 1 (EDS1) conditionally regulate the cell wall when suppressed in transgenic aspen. During four years of growth in the field the following effects were observed: lignin content was reduced, the cellulose fiber polymerization degree increased and the growth itself was unaffected. The wood of transgenic trees was more efficient as a substrate for saccharification, alcoholic fermentation and bioethanol production. The presented results may trigger the development of novel biotechnologies in the biofuel industry.

In recent times, there has been a growing interest in the use of control charts as a feedback process monitoring technique. Particularly, CUSUM schemes have been proven to be efficient for monitoring processes where the magnitude of the sustained mean shifts is small or moderate. However, because of the constant control limits, the detection ability of CUSUM schemes becomes slow at the initial set-up of the process. The fast initial response FIR feature has often been used to enhance it at the process startup. Meanwhile, the dynamism of real-life problems has always encouraged a more sensitive CUSUM scheme capable of detecting process shifts more rapidly. In this paper, an improved CUSUM scheme for monitoring process mean is proposed. This scheme will be substantial for monitoring processes whose observations are obtained at a distant time interval for example hourly, daily or weekly and where the sustained shifts are assumed to be small or moderate. To demonstrate the practical applications of the proposed scheme, we present its real-life application using datasets from a bottling company and petroleum refinery laboratory.

Immune dysfunction has long been reported by medical professionals regarding astronauts suffering from opportunistic infections both during their time in space and a short time period afterwards once back on Earth. Various species of prokaryotes on board these space missions or cultured in a microgravity analogue exhibit increased virulence, enhanced formation of biofilms, and in some cases develop specific resistance for specific antibiotics. This poses a substantial health hazard to the astronauts confined in constant proximity to any present bacterial pathogens on long space missions with a finite number of resources including antibiotics. Furthermore, some bacteria cultured in microgravity develop phenotypes not seen in Earth gravity conditions, providing novel insights into bacterial evolution and research.

Nonhost disease resistance is the most common type of plant defense mechanism against potential pathogens. In this study, the metabolic enzyme formate dehydrogenase (FDH1) was identified to be involved in nonhost disease resistance in Nicotiana benthamiana and Arabidopsis thaliana. In Arabidopsis, AtFDH1 was highly upregulated in response to both host and nonhost bacterial pathogens. Arabidopsis Atfdh1 mutants were compromised in nonhost resistance, basal resistance, and gene-for-gene resistance. The expression patterns of salicylic acid (SA) and jasmonic acid (JA) marker genes after pathogen infections in Atfdh1 mutant indicated that SA is most likely involved in the FDH1-mediated plant defense response to both host and nonhost bacterial pathogens. Previous studies reported that FDH1 localizes to only mitochondria, or both mitochondria and chloroplasts. Our results showed that the AtFDH1 localized to mitochondria and the amount of FDH1 localized to mitochondria increased upon infection with host or nonhost pathogens. Interestingly, the subcellular localization of FDH1 was observed in both mitochondria and chloroplasts after infection with a nonhost pathogen in Arabidopsis. We speculate that FDH1 plays a role in cellular signaling networks between mitochondria and chloroplasts to produce coordinated defense responses such as SA-induced reactive oxygen species (ROS) generation and hypersensitive response (HR)-induced cell death against nonhost bacterial pathogens.

Respiratory Syncytial Virus is a common respiratory pathogen known for causing respiratory illnesses, ranging from mild symptoms to severe lower respiratory tract infections in infants and the elderly. This virus is responsible for one-third of pneumonia deaths in the pediatric population, but there are currently only a few effective vaccines and pharmacological treatments. The frac-talkine (CX3CL1) receptor (CX3CR1) is a co-receptor for RSV expressed by airway epithelial cells and a diversity of immune cells. Recent research has highlighted the role of CX3CR1 in the host immune response to RSV infection, and its potential role in the development of an efficient vaccine and novel treatments.

Host immunological pathways have been proposed including TH1, TH2, TH3, TH9, TH17, TH22, TH1-like, and THαβ immune reactions. Besides TH2 and TH9 immune responses which are against multicellular parasites, host immunological pathways against viruses, intracellular micro-organisms (bacteria, protozoa, and fungi), and extracellular micro-organisms can use programmed cell death pathways to trigger immune reactions or to execute effective strategies to eliminate these pathogens. These programmed cell deaths include apoptosis, autophagic death, pyroptosis, ferroptosis, necroptosis, and NETosis. Apoptosis is related to host anti-virus eradicable THαβ immunity. Autophagic death is related to host anti-virus tolerable TH3 immunity. Pyroptosis is related to host anti-intracellular micro-organism eradicable TH1 immunity. Ferroptosis is related to host anti-intracellular micro-organism tolerable TH1-like immunity. Necroptosis is related to host anti-extracellular micro-organism eradicable TH22 immunity. NETosis is related to host anti-extracellular micro-organism tolerable TH17 immunity.

Food allergies are a growing public health concern worldwide, especially in children and young adults. Allergen-specific IgE plays a central role in the pathogenesis of food allergies, but their titers poorly correlate with allergy development. Host immune systems yield allergen-specific immunoglobulin (Ig)A, IgE and IgG subclasses with low or high affinities and differential Fc N-glycosylation patterns that can affect the allergic reaction to food in multiple ways. High affinity IgE is required to induce strong mast cell activation eventually leading to allergic anaphylaxis while low affinity IgE can even inhibit the development of clinically relevant allergic symptoms. IgA and IgG antibodies can inhibit IgE-mediated mast cell activation through various mechanisms, thereby protecting IgE-positive individuals from allergy development. The production of IgE and IgG with differential allergenic potential seems to be affected by the signaling strength of individual B cell receptors, and by cytokines from T cells. This review provides an overview of the diversity of the B cell response and the diverse roles of antibodies in food allergy.

Like other organisms, fungi produce extracellular vesicles (EVs) that are involved in various biological processes, including intercellular communication and the transport of molecules between cells. These EVs can be applied in fungal pathogenesis, virulence, and interactions with other organisms, including host cells, in the case of fungal infections. While some types of mycoses are relatively common and easily treatable, certain neglected mycoses pose significant public health challenges, such as sporotrichosis, chromoblastomycosis, and paracoccidioidomycosis. These infectious diseases can cause significant morbidity and disability, leading to a reduced quality of life for the patients. So, research about the virulence factor is essential to understand how fungi escape the immune system. In this context, this manuscript reviews the study of fungi EVs, their cargo, their obtaining, and their role during the infectious process, which is extremely important for understanding this neglected mycosis.

Leishmaniasis is a complex infectious parasitic disease caused by protozoa of the genus Leishmania, belonging to a group of neglected tropical diseases. It poses significant global health challenges, particularly in socio-economically disadvantaged regions. Macrophages, as innate immune cells, play a crucial role in initiating the inflammatory response against the pathogens responsible for this disease. Macrophage polarization, the process of differentiating macrophages into pro-inflammatory (M1) or anti-inflammatory (M2) phenotypes, is essential for the immune response in leishmaniasis. The M1 phenotype is associated with resistance to Leishmania infection, while the M2 phenotype is predominant in susceptible environments. Notably, various immune cells, including T cells, play a significant role in modulating macrophage polarization by releasing cytokines that influence macrophage maturation and function. Furthermore, other immune cells can also impact macrophage polarization in a T-cell-dependent manner. Therefore, this review comprehensively examines macrophage polarization's role in leishmaniasis and other immune cells' potential involvement in this intricate process.

We present a new perspective of the link between QED and Maxwell's equations. We demonstrate that the interpretation of $\mathbf{D}=\varepsilon_{0} \mathbf{E}$ as vacuum polarization is consistent with QED. A free electromagnetic field polarizes the vacuum, but the polarization and magnetization currents cancel giving zero source current. The speed of light is a universal constant, while the fine structure constant, which couples the electromagnetic field to matter, runs as it should.

Aim: This study aimed to understand the role of workforce agility as a coping strategy to curtail the COVID-19 pandemic. Method: The study reviewed and integrated two lines of literature to develop a theoretical framework to help business organizations to respond, adapt, and recover from the COVID-19 pandemic crisis. Results: The results showed that there are several commonalities between the workforce agility literature and the crisis management literature, mostly manifested in the speed of responding to uncertain and unpredictable, adverse events in the business environment. A thorough review of key themes in both kinds of literature led to developing a theoretical framework that links crisis drivers, crisis enablers, crisis capabilities, and response strategy. Workforce agility can be used as a coping strategy to deal with the COVID-19 pandemic crisis. Both kinds of literature evolve to respond to any crisis; the crisis management literature focuses on Meso-level (organizational level) or collective actions to mitigate the crisis, while the workforce agility literature focuses on the Micro-level (individual level). However, the successful response to any crisis requires the synergy of both actions. Future Studies: The results of this research are of prime importance for both researchers and practitioners. Researchers can use the theoretical framework as a baseline for building empirical research design. The current study also sets the context for future researchers who are interested in workforce agility to test the validity of agile work behaviors in real adverse context. It also opens a new stream of debate by deconstructing understudied links between workforce agility, resilience, and crisis management. Mangerial implication: For practitioners to ensure a successful response to any impending crisis, they must develop their employees’ agile behaviors. Practitioners can also redesign their recruitment strategy to select the right individuals with the right agile attributes, abilities, and behaviors to easily alter their behaviors according to the progressing crisis phases. Finally, practitioners can design continual learning interventions to include required agile skills and competencies to prepare their employees for future crises.

Mechanical power and motion are often transmitted by the gear-rotor-bearing system. When there are fitting clearances between the housing and outer ring in bearings, complex vibration responses will be generated, which makes the operating status difficult to identify. Therefore, for analyzing dynamic responses, a dynamic model of gear-rotor-bearing systems with bearing fitting clearances is proposed. In the model, the bearing system with fitting clearances and gear pair system are combined, and the coupling relationship is determined by the gyroscopic mo-tion of the shaft. The friction force and collision force caused by fitting clearances are also con-sidered, which are simulated by the Coulomb friction model and Hertz theory. The result shows that the meshing stiffness will also be excited by the bearing displacement. When there are fit-ting clearances on the bearing, the amplitude modulation of the bearing outer raceway to the system time-domain response is intensified, and the multiple harmonic frequency of bearings and gear pairs are generated on the spectrum, as well as defect frequencies of gear pairs. As the fitting clearance is increased, the higher multiple harmonic responses will be caused. Although the response amplitude of the gearbox is increased by raising the input speed, multiple harmon-ic responses are suppressed, which makes the system mainly vibrate at the fundamental fre-quency. Then, the dynamic model and the vibration analysis are experimentally verified.

The role of the immune response to SARS-CoV-2 infection is not yet well known, in particular about the persistence of circulating antibodies. The aim of the study is to compare the results of two automated systems for the determination of IgG antibodies against SARS CoV-2 and to assess the time course of the IgG response after the onset of symptoms for a period longer than that evaluated to date. IgG were measured in 98 specimens of 55 subjects with COVID-19 (time from the onset of symptoms from 3 to 109 days) using the automated tests "Abbott SARS-COV-2 IgG" and the "MAGLUMI 2019-nCoV IgG". The two methods had a concordance of 91.8%, but the quantitative correlation showed very dispersed results. All the specimens resulted positive after 17 days from the onset of the synptoms. However, the median concentrations of IgG, after a rapid increase up to about 20 days, quickly decrease to about 15% of the maximum for Maglumi. The same samples measured by Architect showed a quite constant trend up to 80 day, and then an only moderate decline. The titer of IgG against SARS-CoV-2 in patients exposed to COVID-19 may significantly and rapidly decrease, with a different time-course depending on the method used for the determination.

The human innate immune response to the pore-forming toxin of Vibrio cholerae VCC, is currently under study. Here, in vitro studies on a human macrophage cell line (THP-1), helped explore the activated pathways involved on the onset the innate immune response towards the cytotoxin. The secreted monomeric 65 KDa form interacts with mature macrophages in pg/ml concentrations, determined by dose response experiments after treatments under 1 h. Non vacuolating concentrations (pg/ml) were applied to the cells; immunoblots revealed activation of MAPKs: early overexpression of p38 and ERK. Cell lysis by release of lactate dehydrogenase (LDH) was not apparent in the first hour, nonetheless it was positive after 24 h. Finally, to discern whether the VCC stimulates transcriptional activators via MAPKs pathway, NF-κB and AP-1 were studied by real time quantitation. Increased expression of p50 (NF-κB), cJun and cFos (AP-1) was observed. Given that NF-κB is the transcription factor initiating inflammation of innate immune response and in turn, AP-1 is responsible for cell surviving response, results from this study lead us to conclude that VCC in vitro treatments, induce a pro-inflammatory and a surviving response, in less than one hour on activated macrophages.

Background: Cytokines and chemokines are critical regulators of innate and adaptive immunities during viral infection. We examined innate and adaptive immune responses to hepatitis C virus (HCV) and hepatitis B virus (HBV) at baseline and against controls. Methods: Twenty-seven cytokines were evaluated before treatment in 27 patients with chronic hepatitis C(CHC) [genotype1 (n=20), genotype2 (n=7), HCVRNA 5.72IU/ml] and 12 chronic hepatitis B(CHB) [e-antigen (Ag) (+) (n=5), e-Ag (-) (n=7), HBVDNA 6.191.31Logcopies/ml] and against controls(n=5). Results: Th1 and Th2 cytokines were significantly higher (p<0.05) in CHB than in CHC. The levels of IL-IL10 in CHC and CHB, and IL15 in CHC(genotype2) and CHB were significantly lower (p<0.05) than in controls. The levels of CXCL8 in CHC and CHB, IL12 in CHC and CHB [e-Ag (-)] and CXCL10 in CHC and CHB were significantly higher (p<0.05) than in controls. IFN-γwas higher in CHB than in controls. Conclusion: Cytokines levels differed between CHB and CHC before treatment. Innate immune responses were impaired in CHB with HBeAg(-) and CHC, but not in CHB with HBeAg(+) with high viral loads. Adaptive immune responses were impaired in CHB and CHC and appear to reflect the distinct state of virus-host immune interactions between CHB and CHC.

Background: Liver failure profoundly affects the immune system, leading to dysregulation of innate and adaptive immune responses. Body: This review explores the intricate relationship between liver function and immune homeostasis. The role of the liver as a central hub in immune response initiation is elucidated, emphasizing its involvement in hepatic inflammation induction and subsequent systemic inflammation. Cytokines, chemokines, growth factors, and lipid mediators orchestrate these immune processes, serving as both prognostic biomarkers and potential therapeutic targets in liver failure-associated immune dysregulation. Furthermore, the review delves into the mechanisms underlying immunosuppression in liver failure, encompassing alterations in innate immune cell functions such as neutrophils, macrophages, and natural killer cells (NK cells), as well as perturbations in adaptive immune responses mediated by B and T cells. Conclusion: Understanding the immunological consequences of liver failure is crucial for developing targeted therapeutic interventions and improving patient outcomes in liver disease management.

In mountain-gorge areas, the rock creep is the critical process for high rock slopes failure. During long-term rock creep, slopes might encounter earthquakes and form further creep after earthquakes. This complex mechanical response process can easily lead to the slope failure. Based on a high rock slope in the Nujiang River Basin, this paper analyzes deformation characteristics and dynamic response characteristics by using FLAC3D software, considering combined effects of multiple earthquakes and long-term creep. Results show that when the amplitude increases, the shear strength of the slope decreases and the risk of instability increases under combined actions of creep and earthquakes. Earthquakes promote the development of creep and induce the accumulation of damage on the slope surface and in the slope. The delayed effect becomes more pronounced as the slope height increases. We need to consider deformation differences of the slope further. The ground motion response on the slope surface is stronger than those in the slope, with the peak occurring at the top of the slope. Earthquakes have a greater impact on the middle and top of the slope surface, where cumulative damage and crack development begin. Reinforcement should be considered in these two places. Vertical earthquake has a great effect on the dynamic response. The phenomenon of slope resonance leads to a larger MPGA in the vertical direction than in the horizontal direction. Nonlinear and damping characteristics of the slope and the frequency of seismic waves cause the MPGA to decrease with the increase of amplitudes. This study could promote the development of high rock slope failure mechanism and provide references for the prevention of landslides in the Nujiang River Basin.

In today's digital landscape, cybersecurity has become a priority, with attacks becoming increasingly sophisticated. Traditional security approaches are no longer enough, requiring a more dynamic and advanced response. In this context, integrating Artificial Intelligence (AI) and Machine Learning (ML) appears key to addressing this growing threat. However, despite their high effectiveness, there is a developed problem: the integration of various data sources and technologies for comprehensive protection. This article presents an in-depth review of integrating Artificial Intelligence and Machine Learning in cybersecurity, focusing particularly on Open Extended Detection and Response (Open XDR) technology. The literature review in this article was meticulously conducted with specific criteria in mind. It focused on sourcing peer-reviewed journals, authoritative cybersecurity publications, and recent conferences that primarily concentrate on the advancements in AI and ML within the cybersecurity domain, particularly from 2018 to 2023. This timeframe was chosen to ensure the inclusion of the most current and relevant developments in Open XDR technology, Intrusion Detection Systems, Endpoint Detection and Response, and Security Information and Event Management systems. Additionally, the review gave special attention to studies and reports highlighting practical implementations and real-world applications of these technologies, thereby ensuring a comprehensive understanding of their impact and effectiveness in enhancing cybersecurity resilience. The methodology used is a detailed literature review, examining how various cybersecurity components interact and function. These components include Intrusion Detection Systems (IDS), which monitor networks for malicious activities; Endpoint Detection and Response (EDR), which focuses on detecting and investigating security incidents on endpoints; and Security Information and Event Management (SIEM), systems that provide real-time analysis of security alerts. The review also considers the role of Active Directory, a directory service for Windows domain networks, and the process of log forwarding, where log files are transmitted to a central server for analysis, in the context of AI and ML. The paper delves into the development of AI and ML, underscoring their roles in cybersecurity for advanced data processing, pattern recognition, and predicting threats. It explores both supervised (where the model is trained on labeled data) and unsupervised learning (where the model learns from unlabeled data) in ML, and how these techniques bolster cybersecurity measures. The article highlights the significance of Open XDR as a critical innovation that integrates data from multiple sources for comprehensive security analysis. Further, the review discusses how the integration of AI and ML into various cybersecurity tools, such as IDS, EDR, and SIEM, augments capabilities in threat detection and response. It addresses the challenges and opportunities that AI and ML present in the cybersecurity domain, focusing on ethical issues, data privacy concerns, and the necessity for ongoing professional development in this rapidly advancing field. The paper concludes by affirming the effectiveness of merging AI and ML with these cybersecurity tools within the Open XDR framework.

Pancreatic cancer (PC) has a poor prognosis and displays resistance to immunotherapy. A better understanding of tumor-derived extracellular vesicles (EVs) effects on immune responses might contribute to improved immunotherapy. EVs derived from Capan-2 and BxPC-3 PC cells isolated by ultracentrifugation were characterized by atomic force microscopy, western blot (WB), nanoparticle tracking analysis and label-free proteomics. Fresh PBMCs from healthy donors were treated with PC- or control-derived heterologous EVs followed by flow cytometry analysis of CD8+ and CD4+ lymphocytes. Proteomics of lymphocytes sorted from EV-treated, or -untreated PBMCs was performed and IFN-γ concentration was measured by ELISA. Notably, most of the proteins identified in Capan-2 and BxPC-3 EVs by proteomic analysis were connected in a single functional network (p=1x10-16) and were involved in “Immune System” (FDR: 1.10x10-24 and 3.69x10-19, respectively). Interestingly, treatment of healthy donor-derived PBMCs with Capan-2 EVs, but not with BxPC-3 EVs or heterologous control EVs induced early activation of CD8+ and CD4+ lymphocytes. Proteomics of lymphocytes sorted from EV-treated PBMCs was consistent with their activation by Capan-2 EVs, indicating IFN-γ among major upstream regulators, as confirmed by ELISA. Proteomic and functional analyses indicate that PC-EVs have pleiotropic effects, and some may activate early immune response, which might be relevant for the development of highly needed immunotherapeutic strategies in this immune-cold tumor.

The recent outbreak of Nipah virus in India in 2023 had affected the Kozhikode district in Kerala, with a total of 6 confirmed cases and 2 deaths. The source of the outbreak was traced to fruit bats that contaminated date palm sap, a common drink in the region. The outbreak was contained by rapid detection, isolation, and contact tracing of the cases, as well as public health education and social distancing measures. It also highlighted the need for improved surveillance, diagnostics, and therapeutics for Nipah virus. This letter highlights the latest insights gained from the epidemiological, clinical, and laboratory investigations of the outbreak.

COVID-19 pandemic outbreak challenged the global public health in last couple of years. Throughout the pandemic period, numbers of mutant strains of SARS- CoV-2 created challenges for the infected patients with diverse pathophysiology and immune response. Variant of Concern (VOC) alpha (B.1.1.7), delta (B.1.617.2) and omicron (B.1.1.529) grew most notable for causing the epidemiological manifestations, which eventually caused elevated infectivity resulting in significant mortality. This review indicates the comparative analysis of the immune-pathophysiological mechanisms in respect to the aforementioned strains of SARS-CoV-2.

Salmonella is the intracellular pathogen and etiological known for the cause of asymptomatic carriage, gastroenteritis, systemic disease (typhoid fever), in severe cases death may also occur. Altered function of mitochondria due to Salmonella infection impacts the immune response. Mitochondria which are recognized as the “powerhouse” of the cells are also know to play central role in the immune metabolism. Mitochondrial dynamics such as fusion, fission, signaling, transport and mitophagy influences the immune system and also maintains the cellular integrity. Mitochondrial DNA and Reactive oxygen species formation also elicits the inflammatory responses. This review discusses the immune metabolism and effect of altered mitochondrial dynamics in case of Salmonella infection.

The influence of four levels of dietary supplementation on the development of the immune response and on the biology of Haemonchus contortus and Trichostrongylus colubriformis was evaluated in Dorper lambs under serial artificial mixed-infections with 1000 infective larvae (L3) of each species, given every three days for 12 weeks. For each of the four diets formulated, one infected group (n=7) and one control group (n=4) were set up. Diets 1, 2, 3 and 4 contained 0%, 25%, 50% and 75% of concentrate, respectively. There was an evident immune response to infection in all groups, manifested through eosinophilia and production of anti-L3 immunoglobulins. There was a significant inverse relationship between the levels of nutrients in the diets and the numbers of late fourth-stage larvae, early fifth-stage larvae and adults of H. contortus. Most of the H. contortus parasite population was in hypobiosis at the early-fourth stage, representing 59.5%, 75.8%, 83.3% and 86.3% of the total Haemonchus worm burden, respectively, in the Diets 1, 2, 3 and 4. In the case of T. colubriformis, hypobiosis was not observed and the diet had no influence on establishment of the parasite.

Salvia hispanica (chia) is a highly nutritious food source and has gained popularity due to its high omega-3 fatty acid content. Red spider mites are a serious problem in the production of S. hispanica. However, no study has been conducted to analyse the defensive response to the infestation of red spider mites in S. hispanica. To elucidate the molecular mechanisms of the defensive response of S. hispanica to red spider mites, we performed a transcriptomic analysis of S. hispanica when infested by red spider mites. In the comparative assessment of leaf transcriptomes, a total of 1743 differentially expressed genes (DEGs) were identified between control and mite-infested S. hispanica. From these, 1208 (69%) transcripts were up-regulated and 535 (31%) were down-regulated. The DEGs included transcription factors, defense hormones, and secondary metabolites that were either suppressed or activated in response to spider mite herbivory. Gene Ontology (GO) enrichment analysis revealed that plant secondary metabolites such as glucosinolates, and signalling pathways, including the jasmonic acid signalling pathway, may play an important role in the defence against red spider mites. This study provides novel insights into the defence response of S. hispanica in response to insect herbivory and could be a resource for the improvement of pest resistance in the chia.

In Μay 2022, for the first time, multiple cases of mpox were reported in several non-endemic countries. The first ever case of the disease in Greece was confirmed on 8 June 2022 and a total of 88 cases were reported in the country until the end of April 2023. A multidisciplinary response team was established by the Greek National Public Health Organization (EODY) to monitor and manage the situation. EODY’s emergency response focused on enhanced surveillance, laboratory testing, contact tracing, medical countermeasures, and education of health care providers and the public. Even though management of cases was considered successful and the risk from the disease was down-graded, sporadic cases continue to occur. Here, we provide epidemiological and laboratory features of the reported cases to depict the course of the disease notification rate, that suggests measures for raising awareness as well as vaccination of high-risk groups of the population should be continued.

One of the significant challenges today in the brain-machine interface using invasive methods is the stability of the chronic record. In recent years, polymer-based electrodes have gained notoriety for achieving mechanical strength values close to that of brain tissue, promoting a lower immune response to the implant. In this work, we fabricated fully polymeric electrodes based on PEDOT:PSS for neural recording in Wistar rats. We characterized the electrical properties and both in-vitro and in-vivo functionality of the electrodes. Also, we employed histological processing and microscopical visualization to evaluate tecidual immune response in 7, 14, and 21 days post-implant days. Electrodes with 400-micrometer channels showed a 12dB signal-to-noise ratio. Local field potentials were characterized under two conditions: anesthetized and free-moving. There was a proliferation of microglia to the tissue-electrode interface in the first days, with a decrease after 14 days. Astrocytes also migrated to the interface, but there was no continuous recruitment of these cells in the tissue, showing inflammatory stability at 21 days. The signal was not affected by this inflammatory action, demonstrating that fully polymeric electrodes can be an alternative to prolong the valuable time of neural recordings.

Bunyaviruses represent the largest group of RNA viruses, and are the causative agent of a variety of febrile and hemorrhagic illnesses. Originally characterized as a single serotype in Africa, the number of described bunyaviruses now exceeds over 500, with its presence detected around the world. These predominantly tri-segmented, single-stranded RNA viruses are transmitted primarily through arthropod and rodent vectors, and can infect a wide variety of animal and plants. Although encoding for a small number of proteins, these viruses can inflict potentially fatal disease outcomes, and have even developed strategies to suppress the innate antiviral immune mechanisms of the infected host. This short review will attempt to provide an overall description of the order Bunyavirales, describing the mechanisms behind their infection, replication and their evasion of the host immune response. Furthermore, the historical context of these virus will be presented, starting from their original discovery almost 80 years ago, to the most recent research pertaining to viral replication and host immune response.

Deaths and property damage from the flood have increased drastically in the past two decades due to various reasons such as increased population, unplanned development and climate change. Losses from floods can be reduced by having accurate intelligence of an emerging flood situation in order to make timely decisions for issuing early warnings and responding efficiently. This paper presents a thorough analysis of the types and sources of intelligence required for flood warning and response processes and technology solutions that can be used for capturing such intelligence. A structured review, covering a more comprehensive range of published literature on Flood Early Warning and Response Systems (FEWRS), was conducted to identify the necessary intelligence and the technology that can be used to capture intelligence required for various phases of a flood hazard as it develops. Twenty-seven different types of key intelligence required in the flood cycle were identified. A conceptual architecture was identified that illustrates how relevant technology solutions can be used to extract intelligence at various stages of a flood event for decision making for early warnings and response.

Background: We aimed to identify overexpressed genes or related pathways associated with good responses to anti-HER2 therapy and to suggest a model for predicting drug response in neoadjuvant therapy with trastuzumab in HER2-positive breast cancer patients. Methods: We recruited 64 women with breast cancer and categorized them into three groups according to anti-HER2 therapy response. RNA from twenty core needle biopsy paraffin-embedded tissues and four cultured cell was extracted, reverse transcribed, and subjected to microarray. The obtained data were analyzed using Gene Ontology, Kyoto Encyclopedia of Genes and Genomes, and database for annotation, visualization, and integrated discovery. Results: In total, 6,656 genes differentially expressed between trastuzumab-susceptible and trastuzumab-resistant cell lines (3,224 upregulated and 3,432 downregulated). Expression changes in 34 genes in several pathways were found to be related to the response to trastuzumab-containing treatment, interfering with adhesion to other cells or tissues (focal adhesion) and regulating extracellular matrix interactions and phagosome action. Thus, decreased tumor invasiveness and enhanced drug effects might be the mechanisms explaining the better drug response in complete response group. Conclusions: This multigene assay-based study provides insights into breast cancer signal transduction and the possible prediction of treatment response to targeted therapies such as trastuzumab.

Molecular iodine (I2) induces apoptotic, antiangiogenic, and antiproliferative effects in breast cancer cells. Little is known about its effects on the tumor immune microenvironment. We studied the effect of oral (5 mg/day) I2 supplementation alone (I2) or together with conventional chemotherapy (Cht+I2) on the im-mune component of breast cancer tumors from a previously published pilot study conducted in Mexico. RNA-seq, I2 and Cht+I2 samples showed significant increases in expression of Th1 and Th17 pathways. Tumor immune composition determined by deconvolution analysis revealed significant increases in M0 macrophages and B lymphocytes in both I2 groups. Real-time RT-PCR showed that I2 tumors overexpress T-BET (p = 0.019) and interferon-gamma (IFNγ; p = 0.020) and silence tumor growth factor-beta (TGFβ; p = 0.049); whereas in Cht+I2 tumors, GATA3 is silenced (p = 0.014). Preliminary methylation analysis shows that I2 activates IFNγ gene promoter (by increasing its unmethylated form) and silences TGFβ in Cht+I2. In conclusion, our data showed that I2 supplements induce the activation of the immune response and that when combined with Cht, the Th1 pathways are stimulated. The molecular mechanisms involved in these responses are being analyzed, but preliminary data suggest that methylation/demethylation mechanisms could also participate.

Purpose: This study aimed to determine the efficacy and safety of Oncoxin as an antitumoral supplement, and to describe its mechanism of action. Methods: We performed this scoping review according to the recommendations of the Joanna Briggs Institute and included patients older than 18 years-old who have any kind of tumor and receive Oncoxin as a supplement. We focused on the efficacy in terms of antitumoral properties, quality of life and survival, safety in terms of adverse events, and the mechanism of action. We did not limit for language or setting. We searched MEDLINE (Pubmed), EMBASE (Scopus), LILACS, and the Cochrane Central Register of Controlled Trials (CENTRAL) from inception to nowadays. Results: We found a promising increment of survival when taking Oncoxin as a supplementary treatment. Additionally, the quality of life increased in terms of Karnofsky and EORTC scales. Regarding the mechanism of action, studies suggest it modifies inflammatory mediators’ expression, as evidenced by the reduction of COX-2, IL-1β, IL-6, TNF-α, IL-1β, IL-12, and IFN-γ. Besides, it promotes an arrest in the progression of cells from G1 into S, along with an increase in p27 and a decrease in cyclin D1 and pRb. Conclusions: We found promising complementary effects of Oncoxin to the standard treatment of cancer patients in diverse scenarios, with putative robust mechanisms of action. In addition to clinically relevant impacts verified in clinical trials, as well as it decreases the levels of pro-inflammatory cytokines, it can also decrease cytokines with antitumor activity such as IFN-γ, which should be further explored in larger trials and the long term.

Background: The COVID-19 has put global health institutions on alert. Organizations such as the CDC and WHO have developed preparedness and prevention checklist of 2019-nCoV infection to be used by public and healthcare professionals. Since COVID 19 pandemic is unexpected and no country aware of it prior to outbreak, there is limited information on the overall preparations of healthcare providers in Ethiopia. Therefore, the aim of this study was to assess early healthcare professionals’ preparedness and response to COVID 19 Pandemic in Oromia regional state, Ethiopia. Methods: The study was conducted on healthcare professionals working in public hospitals of Oromia regional state. The study was carried out by online questionnaire prepared using SurveyMonkey©. The collected data was analyzed and One-way ANOVA was used to determine the significant differences between health professionals working in different hospitals. The statistical significance associations of variables of interest was determined at 95% confidence intervals. Results: Healthcare professionals in the public hospitals of Oromia regional state, Ethiopia perceived that they are not yet well prepared and may not respond to the pandemic quickly and efficiently. Even though, they have positive response towards identifying signs and symptoms, provide education and utilization of PPE, they are still lacking in practical responses like managing cases, implementing emergency plans and isolation procedures from many others. Conclusion: As the Federal Ministry of Health, Ethiopia Public health institute and Oromia health bureau are vigilant and continually conducting preventive measures programs, extensive and maximum effort should be done to improve healthcare providers’ preparedness and response towards any emergency related to COVID-19 pandemic.

Optical conductivity of an interacting polaron gas is calculated within an extended random phase approximation which takes into account mixing of collective excitations of the electron gas with LO phonons. This mixing is important for the optical response of strongly polar crystals where the static dielectric constant is rather high, as in the case of strontium titanate. The present calculation sheds light on unexplained features of experimentally observed optical conductivity spectra in $n$-doped SrTiO$_{3}$. These features appear to be due to dynamic screening of the electron-electron interaction by polar optical phonons and hence do not require additional mechanisms for their explanation.

Adenosine to inosine (A-to-I) RNA editing is a highly conserved regulatory process carried out by adenosine-deaminases (ADARs) on dsRNAs. Although a considerable fraction of the transcriptome is edited, the function of most editing sites is unknown. Previous studies indicate changes in A-to-I RNA editing frequencies following exposure to several stress types. However, the overall effect of stress on the expression of ADAR targets is not fully understood. Here, we performed high-throughput RNA sequencing of wild-type and ADAR mutant C. elegans worms after heat-shock to analyze the effect of heat-shock stress on the expression pattern of genes. We found that ADAR regulation following heat-shock does not directly involve heat-shock related genes. Our analysis also revealed that lncRNAs and pseudogenes, which have a tendency for secondary RNA structures, are enriched among upregulated genes following heat-shock in ADAR mutant worms. The same group of genes is downregulated in ADAR mutant worms under permissive conditions, which is likely, considering that A-to-I editing protects endogenous dsRNA from RNA-interference (RNAi). Therefore, temperature increases may destabilize dsRNA structures and protect them from RNAi degradation, despite the lack of ADAR function. These findings shed new light on the dynamics of gene expression under heat-shock in relation to ADAR function.

The response of plasmonic metal particles to an electromagnetic wave undergoes significant features at the nanoscale level. Different properties of the internal composition of a metal, such as its ionic background and the free electron gas, begin to manifest more prominently. As the dimensions of the nanostructures decrease, the classical local theory gradually becomes inadequate. Therefore, Maxwellʹs equations need to be supplemented with a relationship determining the dynamics of current density which is the essence of nonlocal plasmonic models. In this field of physics, the standard (linearized) hydrodynamic model (HDM) has been widely adopted with great success, serving as the basis for a variety of simulation methods. However, ongoing efforts are also being made to expand and refine it. Recently, the GNOR (general nonlocal optical response) modification of the HDM has been used, with the intention of incorporating the influence of electron gas diffusion. Clearly, from the classical description of fluid dynamics, a close relationship between viscosive damping and diffusion arises. This offers a relevant motivation for introducing the GNOR modification in an alternative manner. The standard HDM and its existing GNOR modification also do not include the influence of interband electron transitions in the conduction band and other phenomena that are part of many refining modifications of the Drude‐Lorentz and other models of metal permittivity. In this article, we present a modified version of GNOR‐HDM that incorporates the viscosive damping of the electron gas and a generalized Drude‐Lorentz term. In the selected simulations, we also introduce Landau damping which corrects the magnitude of the standard damping constant of the electron gas based on the size of the nanoparticle. We have chosen a spherical particle as a suitable object for testing and comparing HD models and their modifications because it allows finding precise analytical solutions for the interaction and, simultaneously, it is a relatively easily fabricable nanostructure in practice. Our contribution also includes our own analytical method for solving the HDM interaction of a plane wave with a spherical particle. This method forms the core of calculations of the characteristic quantities, such as the extinction cross‐sections and the corresponding components of electric fields and current densities.

Lifestyle interventions can prevent type 2 diabetes (T2DM). However, some in-dividuals do not experience anticipated improvements despite weight loss. Bi-omarkers to identify such individuals at early stages are lacking. IGF-1 and IGFBP-1 were shown to predict T2DM onset in prediabetes. We assessed if these markers also predict the success of lifestyle interventions, thereby possibly guid-ing personalized strategies. We analyzed fasting serum levels of IGF-1, IGFBP-1 and IGFBP-2 in relation to changes in metabolic and anthropometric parameters, including intrahepatic li-pids (IHL) and visceral adipose tissue (VAT) volume measured by MRI, in 345 high-risk prediabetic participants (54% female; aged 36-80 years). Participants were enrolled in three randomized dietary intervention trials and assessed both at baseline and one year post-intervention. Statistical analyses were performed using IBM SPSS Statistics (version 28), significance set at p