Silicone rubber formulations in the form of thin discs have been studied under room ambient conditions for their surface characteristics. The samples were silicone rubber manufactured in laboratory and those industrially manufactured. The measurements were done using an electrometer high resistance meter, applying dc voltage under normal room ambient conditions. The results show that the silicone rubber samples show higher values of surface resistivity when the dc voltage was applied. Silicone rubber samples manufactured in laboratory seem to exhibit erratic behaviour unlike their corresponding silicone rubbers manufactured in industry; this could be due to manufacturing shortcomings in laboratory and the irregularities in the way the silicone rubber adhered to the concentric ring electrodes. The empirical current traversing the surface of the silicone rubbers does not decay exponentially but rather it decays as an exponential power of the energization time.

The aerodynamic efficiency of a NACA 0012 AR 4 wing was affected through periodic contours aligned in the flow direction resembling a “wrinkled” texture. Streamwise and cross-stream Particle Image Velocimetry (PIV) were conducted at the University of Dayton Low Speed Wind Tunnel (UD-LSWT) around Reynolds number of 135,000 on the NACA 0012 AR 4 wing with and without surface contours. Wings with 6 contour sections was designed by spline fitting two NACA 0012 airfoil profiles in the spanwise direction. Both 2D (wall-to-wall model) configuration and 3D configuration of the wings were tested to determine the effects of surface contours on the parasite and induced drag of the wing. Streamwise PIV results indicated an increase in momentum deficit in the wake of the mid-contour region due to enhanced boundary layer separation from the upper surface of the mid-contour region. The cross-stream PIV results indicated a decrease in the magnitude of azimuthal velocity, circulation and RMS quantities in the wingtip vortex with the surface contours. The reduction in the wingtip vortex properties indicates that the contours were effective in blocking the spanwise flow feeding into the wingtip vortex on the surface of the wing

This study provides, to our knowledge, the first detailed analysis of how surface oil modifies air-sea interaction in a two-way coupled model, i.e., the coupled-ocean-atmosphere-wave-sediment-transport (COAWST) model modified to account for oil-related changes to air-sea fluxes. This study investigates the effects of oil on surface roughness, surface wind, surface and near surface temperature differences, and boundary-layer stability, and how those conditions ultimately affect surface stress. We first conducted twin coupled modeling simulations with and without the influence of oil over the Deepwater Horizon (DWH) oil spill period (April 21 to May 5, 2010) in the Gulf of Mexico. Then we compared the results by using a modularized flux model with parameterizations selected to match those selected in the coupled model adapted to either ignore or account for different atmospheric/oceanic processes in calculating surface stress. When non-oil inputs to the bulk formula treated as unchanged by oil, the surface stress changes are always negative due to oil-related damping of surface roughness alone. However, the oil-related changes to 10-m wind speed and boundary-layer stability are found to play a dominant role in surface stress changes relative to those due to the oil-related surface roughness changes, highlighting that most of the changes in surface stress are due to the oil-related changes in wind speed and boundary-layer stability. Finally, the oil-related changes to surface stress due to the combined oil-related changes in surface roughness, surface wind, and boundary-layer stability are not large enough to have a major impact on the surface current and surface oil transport, indicating that the feedbacks from the surface oil to the surface oil movement itself are minor for forecasting the surface oil transport unless the fractional oil coverage is much larger than found in this study.

Various methods of polymer surface tailoring have been studied to control the changes in wetting behavior. Polymers having precisely controlled wetting behavior in a specific environment are blessed with a wealth of opportunities and potential applications exploitable in biomaterial engineering. The controlled wetting behavior can be obtained by combining surface chemistry and morphology. Plasma assisted polymer surface modification technique have played a significant part to control surface chemistry and morphology. This review focuses on plasma polymerization and investigations regarding surface chemistry, surface wettability, coating kinetics, as well as coating stability. We begin with brief overview of plasma polymerization; these include growth mechanisms of plasma polymerization and influence of plasma parameters. Next, surface wettability and theoretical background structures and chemistry of superhydrophobic and superhydrophilic surfaces. In this review, overview of recent work on tunable wettability by tailoring surface chemistry and physical appearance (i.e. substrate texture) is also described. The formation of smart polymer coatings, which adjust their surface wettability by according to outside environment, including, pH, light, electric field and temperature. Finally, the applications of tunable wettability and pH responsiveness of polymer coatings in real life are addressed. This review should be of interest to plasma surface science communality specifically focused controlled wettability of smart polymer surfaces.

In this study, the NiCrAlY coating was prepared using the atmospheric plasma spraying (APS). The sample was then exposed to a continuous fiber laser beam. Laser surface melting (LSM) can effectively homogenize the composition of the coating. It also reduced the defects and roughness. The coating was examined using optical microscopy (OM), scanning electron microscopy (SEM), and X-ray diffraction (XRD) analysis. The process parameters of the LSM consist of laser power and scan rate. The high-temperature oxidation test was conducted for 200 hours at a temperature of 1100 °C. After a period of 200 hours, the primary coating demonstrated the emergence of an aluminum oxide layer, along with the presence of harmful spinel oxides. The laser remelting technique was used to modify the surface, which led to the uniform growth and development of an aluminum oxide layer (α-Al₂O₃) during the oxidation examination. Therefore, it appears that the reduction in grain size caused by laser remelting prevents the wrinkling of Al2O3 oxide. This process represents a novel and alternative approach to modifying MCrAlY coatings.

The erosion of surface pipelines induced by proppant flowback during shale gas production is significant. The surface pipelines in a shale gas field in the Sichuan Basin experienced perforation failures after only five months of service. To investigate the erosion features of L360N, coatings, and ceramics and optimize the selection of two protective materials, a gas-solid two-phase flow jet erosion experimental device was used to explore the erosion resistance of L360N, coating, and ceramic under different impact velocities (15 m/s, 20 m/s, and 30 m/s). An energy dispersive spectroscope, a scanning electron microscope, and a laser confocal microscope were employed to analyze erosion morphologies. With the increase in flow velocity, erosion depth and erosion rate of L360N, coating, and ceramic increased and peaked under an impact velocity of 30 m/s. Maximum erosion rate and maximum erosion depth of L360N were respectively 0.0350 mg/g and 37.5365 µm. Its primary material removal mechanism was plowing of solid particles and microcracks were distributed on the material surface under high flow velocities. Maximum erosion rate and maximum erosion depth of coating were respectively 0.0217 mg/g and 18.9964 µm. Its primary material removal mechanism was the detachment of the binder phase Co caused by plowing. Maximum erosion rate and maximum erosion depth of ceramics were respectively 0.0108 mg/g and 12.4856 µm. The erosion mechanisms were micro-cutting and plowing. Under different particle impact velocity, different erosion morphologies were observed, but the primary erosion mechanism was the same. The erosion resistance of ceramics was higher than that of coating. Therefore, ceramic lining materials could be used to protect the easily eroded parts, such as pipeline bends and tees, and reduce the failure rate by more than 93%. The study provided the data and theoretical basis for the theoretical study on oil and gas pipeline erosion and pipeline material selection.

The work contains a detailed analysis of the electromagnetic field originating from a point source placed above the layered structure.The surface impedance of the multilayer dielectric structure was determined. Based on the boundary conditions, a method for determining the surface impedance of a layered structure with a perfectly conductive screen and or a magnetic screen is presented. The resonance conditions and the conditions for the excitation of surface waves are derived. The integral expression defining the generalized impedance was analyzed with a view to adapting it to numerical implementation. This allowed the development of a computer program based on which calculations were made of the effect of excitation of waves on multilayer dielectric substrates.

The development of sensitive and specific exosome detection devices is highly desirable because it is believed to deliver specific important information for cancer screening, diagnosis, and monitoring. Among many detection techniques, nanoplasmonic sensors are optical detection methods that offer advantages in sensitivity and detection speed and this makes the sample analysis process faster and more accurate. This paper summarizes the development of nanoplasmonic biosensors, especially Surface Plasmon Resonance (SPR) and Localized Surface Plasmon Resonance (LSPR)-based biosensors for exosome detection. There are three main parts in this paper. The first part will focus on introducing the theoretical background regarding the working principles of SPR and LSPR biosensors. After that, we will introduce several methods that can be used for exosome isolation. This article will close by explaining the engineering of nanoplasmonic sensors both in terms of transducer modification to amplify the signal and functionalization strategies to increase sensor specificity. In this section, the detection mechanism, the type of exosomes detected, and the resulting detection limits are some of the points highlighted in this paper.

We report on a 2D-gap surface plasmon metasurface based composed of a bottom metal layer, middle insulator layer, and top metal nanostructure of gold nanoblocks (nanoantennas). The proposed structure enables us to generate simultaneous multi plasmonic resonances and offers the possibility to tune them, within the near-infrared domain. The simplicity of the metasurface makes it promising for compact optical platforms based on reflection mode operation with potential application in multi-channel biosensors, second-harmonic generation, and multi-wavelength surface-enhanced spectroscopy among other interesting fields

Studying the interaction between the upper ocean and the typhoons is crucial to improve our understanding of heat and momentum exchange between the ocean and the atmosphere. In recent years, the upper ocean responses to typhoons have received considerable attention. The sea surface cooling (SSC) process has been repeatedly discussed. In the present work, case studies were examined on five strong and super typhoons that occurred in 2016—LionRock, 1610; Meranti, 1614; Malakas, 1616; Megi, 1617; and Chaba 1618—to search for more evidence and new features of typhoon’s impact on the sea surface environment. The typhoon monitoring data from the Central Meteorological Observatory, the sea surface temperature (SST) data from satellite microwave and infrared remote sensing, and the sea surface height anomaly (SSHA) data from satellite altimeters were used to analyze in detail: the SSC features caused by typhoons, the relationship between the SSC and the typhoon travelling speed, and the variations in cold and warm eddies during typhoon passage. Results showed that: (1) SSC generally occurred during typhoon passage and the degree of SSC was always determined by the strength and the travelling speed of the typhoon, as well as the initial SST. (2) One day before or on the day of typhoon passage, the SSHA slightly increased due to low surface pressure. After the typhoon passed, the SSHA obviously decreased along with the SSC. The pre-existing positive SSHAs, which always represent warm eddies, decreased or disappeared during typhoon passage, whereas negative SSHAs or cold eddies were enhanced. (3) New cold eddies were generated, especially at the turning points of the typhoon path. The presence of warm eddies is suggested to have a strengthening effect on the typhoons.

Post-mortem characterisation is a pivotal tool to trace back to the origin of structural failures in modern engineering analyses. This work presents a comparison of both the crack propagation profiles and the rupture roughness profiles based on areal parameters for total fracture area. Notched and smooth samples made of weather-resistant structural steel (10HNAP), popular S355J2 structural steel and aluminium alloy AA2017A under bending, torsion, and combined bending-torsion are investigated. After the fatigue tests, fatigue fractures are measured with an optical profilometer, and the relevant surface parameters are critically compared. The results show a great impact of the loading scenario on both the local profiles and the total fracture areas. In this work, the results of both approaches (local and total fracture zones) for specimens with different geometries are investigated. For all specimens, measured texture parameters decreased in the following order: total area, rupture area, and propagation area.

The Olympic Games are a sporting event and a catalyst for urban development in the host city. In this study, we utilized remote sensing and GIS techniques to examine the impact of the Olympic infrastructure on the surface temperature of urban areas. Using Landsat Series Collection 2 Tier 1 Level 2 data, cloud computing, and Google Earth Engine (GEE) methods, this study examines the effects of various Olympic Games facility urban planning in different historical moments and location typologies: monocentric, polycentric, peripheric and clustered Olympic ring. The GEE code applies to the Olympic Games from Paris’24 to Munich’72. However, this paper focuses specifically on the representative cases of Paris’24, Tokyo’20, Rio’16, Beijing’08, Sydney’00, Barcelona’92, Seoul’88, and Montreal’76. The study is not only concerned with obtaining absolute Land Surface Temperatures (LST), but rather the relative influence of mega-event infrastructures on mitigating or increasing the urban heat. As such, locally Normalized Land Surface Temperature (NLST) was utilized for this purpose. In some cities (Paris, Tokyo, Beijing, and Barcelona), it is identified that Olympic planning has resulted in the development of green spaces, creating "green spots" that contribute to lower-than-average temperatures. However, it should be noted that there is a significant variation in temperature within intensely built-up areas, such as Olympic villages and the surrounding areas of the Olympic stadium, which can become “hotspots”. Therefore, it is important to acknowledge that different planning typologies of Olympic infrastructure can have varying impacts on city heat islands, with the polycentric and clustered Olympic ring typologies displaying a mitigating effect. This research contributes to a cloud computing method that can be updated for future Olympic Games or adapted for other mega-events and utilizes a widely available remote sensing data source to study a specific urban planning context.

Although there is a common physiological notion that the origin of the membrane potential is attributed to transmembrane ion transport, it is theoretically possible to explain its generation by the mechanism of ion adsorption. It was previously suggested that the ion adsorption mechanism led even to the potential formulas which are even identical to either the famous Nernst equation or Goldman-Hodgkin-Katz equation. Our further analysis shown in this paper indicates that the potential formula based on the ion adsorption mechanism leads to one equation which is the function of material surface charge density and the material surface potential. Furthermore, we confirmed that the equation holds in all the different experimental systems we studied. Although we have not succeeded in elucidating why such an equation is established, the equation appears to be the key equation governing the characteristics of the membrane potential regardless of the systems in question.

An all-weather land surface temperature (LST) product derived at the Satellite Application Facility on Land Surface Analysis (LSA-SAF) is presented. The product is based on clear-sky LST retrieved from MSG/SEVIRI infrared (IR) measurements, complemented by LST estimated with a land surface energy balance (EB) model to fill gaps caused by clouds. The EB model solves the surface energy balance mostly using products derived at LSA-SAF. The new product is compared with in situ observations made at 3 dedicated validation stations, and with a Microwave (MW) based LST product derived from AMSR-E measurements. The validation against in-situ LST indicates an accuracy of the new product between -0.8 K and 1.1 K and a precision between 1.0 K and 1.4 K, generally showing a better performance than the MW product. The EB model shows some limitations concerning the representation of the LST diurnal cycle. Comparisons with MW LST generally show higher LST of the new product over desert areas, and lower LST over tropical regions. Several other imagers provide suitable measurements for implementing the proposed methodology, which offers the potential to obtain a global, nearly gap-free LST product.

Daily maximum surface air temperature (Tamax) is a crucial factor for understanding complex land surface processes under rapid climate change. Remote detection of Tamax has widely relied on the empirical relationship between air temperature and land surface temperature (LST), a product derived from remote sensing. However, little is known about how such a relationship is affected by the high heterogeneity in landscapes and dynamics in seasonality. This study aims to advance our understanding of the roles of land cover and seasonal variation in the estimation of Tamax using the MODIS (Moderate Resolution Imaging Spectroradiometer) LST product. We developed statistical models to link Tamax and LST in the middle and lower reaches of the Yangtze River in China for five major land-cover types (i.e., forest, shrub, water, impervious surface, cropland, and grassland) and two seasons (i.e., growing season and non-growing season). Results show that the performance of modeling the Tamax-LST relationship was highly dependent on land cover and seasonal variation. Estimating Tamax over grasslands and water bodies achieved superior performance; while uncertainties were high over forested lands that contained extensive heterogeneity in species types, plant structure, and topography. We further found that all the land-cover specific models developed for the plant non-growing season outperformed the corresponding models developed for the growing season. Discrepancies in model performance mainly occurred in the vegetated areas (forest, cropland, and shrub), suggesting an important role of plant phenology in defining the statistical relationship between Tamax and LST. For impervious surfaces, the challenge of capturing the high spatial heterogeneity in urban settings using the low-resolution MODIS data made Tamax estimation a difficult task, which was especially true in the growing season.

Additive manufacturing (AM) technologies show potential for the development of functionally integrated lightweight designs, biomimetic structures and material savings. Typically, as-built surfaces show powder particle agglomerations and re-entrant features, leading to rough surfaces, which are associated with poor fatigue performance. To benefit from the full range of advantages with special focus on aerospace applications, critical features for crack initiation when subjected to fatigue loading need to be identified and mitigated. A first step toward achieving this goal is the surface texture characterisation based on the quantification of surface features. In this paper, selected areal height, functional and feature parameters from ISO 25178-2:2022 are generated and process-specific features are examined for as-built AlSi7Mg0.6 from laser powder bed fusion (PBF-LB). A connection with the particle size distribution of the used powder is demonstrated. It is shown that surface feature analysis opens up opportunities to use physically meaningful surface characteristics in future quality assurance and part qualification processes.

The distribution of impervious surface is one of the important assessment indicators for evaluating the quality of urban ecological environment. Taking Xuzhou city as an example, we study the influence of the spatial distribution of impervious surfaces on urban surface temperature, using Landsat 8 remote sensing imagery and nighttime lighting data to extract the impervious surface information from 2013 to 2022 and carry out surface temperature inversion. The study area was divided into built-up and non-built-up areas using nighttime lighting data and the relevant indices were used to establish interest zones and finally the extraction of impervious surfaces was completed using supervised classification methods. The experimental results show that the kappa coefficient is not less than 0.8562, which makes the result more reliable. By extracting the impervious surface of Xuzhou City, it was found that the impervious surface of Xuzhou City continued to increase from 2013 to 2022, in which the growth rate was faster in 2014-2016 and 2019-2021, and slowed down in 2017-2018 and 2021-2022. The expansion of impervious surface was found to be one of the reasons for the increase of urban surface temperature through stacked analysis and linear regression analysis.

Objective: To determine the effect of sandblasting before and after sintering on the surface roughness of zirconia and the micro-tensile bond strength of a pressable veneering ceramic to zirconia. Methods: Pre-sintered zirconia blocks (IPS e.max ZirCAD, Ivoclar Vivadent) were divided into a control group (CTR, no surface treatment) and four test groups of three specimens each: Pre-S-30, Pre-S-50, Pre-S-110 were sandblasted with 30µm SiO2, 50µm Al2O3 and 110µm Al2O3 particles respectively, before sintering, Post-S-30 was sandblasted with 30µm SiO2 after sintering. For each treatment, the surface roughness was measured (Ra, Perthometer M4P, Mahr Perthen). After sintering the zirconia blocks, a liner and a pressable ceramic (IPS e.max ZirPress, Ivoclar Vivadent) were fired. Sixteen micro-bars were obtained from each block and submitted to the micro-tensile bond strength (µTBS) test. Data were analyzed with one-way ANOVA. Any correlation between Ra and µTBS was evaluated (Sperman test). Results: Sandblasting before sintering with 110µm Al2O3 (Ra=3.44±0.44µm), 50µm Al2O3 (Ra=2.32±0.46µm), and 30µm SiO2 (Ra=1.22±0.22µm) resulted in significantly higher roughness than sandblasting after sintering with 30µm SiO2 (Ra=0.46±0.11µm). The highest µTBS was measured when the sintered zirconia was sandblasted with 30μm SiO2 (26.79±14.80 MPa), which was significantly different from that of specimens that were sandblasted before sintering (Pre-S-30=20.90±11.70; Pre-S-50=21.27±15.19; Pre-S-110=23.99±16.83) or were not treated (CTR=17.44±14.03). Conclusions: Sandblasting zirconia before sintering enhances the surface roughness proportionally to the particle size of the sand used. Sandblasting with 30µm SiO2 after sintering appeared to improve bonding between the veneering ceramic and zirconia. Clinical Significance: Sandblasting with 30µm SiO2 after sintering may improve bonding between veneering ceramics and zirconia, thus reducing ceramic fractures/chippings.

Here, our data provide the first evidence for the existence of a previously unknown receptive system formed by novel DNA- and RNA-based receptors in eukaryotes. This system, named the TR-system, is capable of recognizing and generating a response to different environmental factors and has been shown to orchestrate major vital functions of fungi, mammalian cells, and plants.Recently, we discovered the existence of a similar regulatory system in prokaryotes. These DNA- and RNA-based receptors are localized outside of the membrane forming a type of a network around cells that respond to a variety of chemical, biological, and physical factors and enabled the TR-system to regulate major aspects of eukaryotic cell life as follows: growth, including reproduction and development of multicellular structures; sensitivity to temperature, geomagnetic field, UV, light, and hormones; interaction with viruses; gene expression, recognition and utilization of nutrients. The TR-system was also implicated in cell memory formation and was determined to be responsible for its maintenance and the forgetting of preceding events. This system is the most distant receptive and regulatory system of the cell that regulates interactions with the outer environment and governs the functions of other receptor-mediated signaling pathways.

The surface chemistry and the morphology of SnO2 nanowires, deposited by Vapour Phase Deposition (VPD) method on Au-covered silicon substrate, were studied before and after subsequent air exposure. For this purpose, surface-sensitive methods including X-ray Photoelectron Spectroscopy (XPS), Thermal Desorption Spectroscopy (TDS) and the Scanning Electron Microscopy (SEM) were applied. The studies presented within this paper allowed to determine the surface non-stoichiometry combined with the presence of carbon contaminations, in a good correlation with the surface morphology. The relative concentrations of the main components [O]/[Sn]; [C]/[Sn]; [Au]/[Sn] together with the O – Sn; O – Si bondings were analyzed. The results of TDS remained in a good agreement with the observations from XPS. Moreover, conclusions obtained for SnO2 nanostructures deposited with the use of Au catalyst were compared to the previous obtained for Ag-assisted tin dioxide nanowires. The information obtained within this studies are of great importance for the potential application of SnO2 nanowires deposited on Au covered Si substrate in the field of novel chemical nanosensor devices, since the results can provide an interpretation of how aging effects influence gas sensor dynamic characteristics.

Given the rise in the number of cases and their recurrences, Urinary Tract Infections (UTI) are one of the major burdens on public healthcare worldwide. Rapid, inexpensive and selective detection of Uropathogenic E. coli (UPEC), a major contributor to UTIs, is the need of the hour for effective treatment, given the rise of antibiotic-resistant bacteria due to improper diagnosis. Here we present a rapid, real-time, selective and label-free detection of UPEC using an integrated sensing platform based on Crossed Surface Relief Gratings (CSRGs) as nanoplasmonic sensors. Detection is achieved due to the unique Surface Plasmon Resonance (SPR)-based light energy exchange attributed to the CSRGs, allowing real-time sensing in a very narrow bandwidth of the incident light to pass where the SPR energy conversion occurs. The sensing ability of the platform is experimentally demonstrated by the detection of bulk Refractive Index (RI) changes, with a bulk sensitivity of 382.2 nm/RIU and a resolution in the order of 10-6 RIU. We demonstrate selective capture and detection of clinical concentration of UPEC, as opposed to other gram-negative bacteria, in real-time, a first for CSRGs. This work is particularly important for effective treatment of UTIs, allowing point-of-care diagnosis for economically disadvantaged regions around the world.

Blood has certain significant physical properties, which the authors investigated. This paper provides values of surface tension and viscosity of blood at 37 °C, as well as relationship between them plotted on a cross-plot. By applying Hagen- Poiseuille equation and Jurin's law to the experimentally obtained data, the authors calculated with great accuracy viscosity and surface tension of blood. Evaluating both of the properties using described methods required from the authors to know the density of investigated liquid, which was found to be on average $\rho=1063,56 \frac{kg}{m^3}$. The authors took blood samples from 30 healthy subjects and determined aforementioned physical properties. There has been made a distinction in regard of a sex of the blood donor. Results indicate that both surface tension and viscosity are independent from sex of a subject, as well as indicate that there is no correlation between viscosity and surface tension of blood at 37\degree C. Average values of surface tension and viscosity were found to be $\sigma=5,241\pm 0,262 \cdot 10^{-2}\frac{J}{m^2}$ and $\eta=3,352\pm0,360 \cdot 10^{-3} Pa \cdot s$, respectively.

Titanium membranes are used for guided bone regeneration in implant therapy. However, as a bioinert material, titanium does not have the ability to accelerate bone formation. Various titanium surface treatments to confer bioactivity have been demonstrated; however, there are concerns about the influence of chemical treatments on the corrosion of thin titanium membranes. This study investigated the influence of surface modifications on the structure of thin titanium membranes. Titanium membranes of 20 µm thickness were treated with acid or alkali solutions, and we evaluated their surface structure, wettability, corrosion depth, and mechanical strength compared to non-treated membranes. Alkali-treated thin titanium membranes displayed the formation of nanoscale pore structures on their surfaces, enhanced hydrophilicity, and less corrosion depth compared with acid-treated membranes. Furthermore, the tensile strength of alkali-treated membranes was comparable to non-treated membranes. These results suggest that alkali treatment is an appropriate surface modification method for thin titanium membranes.

Recently, a high internal surface of the titanium alloy pipe is required due to the increment of various applications of the pipe such as aerospace. However, the traditional machining process is unable to effectively polish the internal surface of the slender pipe. Thus, a vertical magnetorheological polishing (VMRP) apparatus is carried out in this work to implement high polishing performance on the internal surface of the titanium alloy pipe. The polishing process is realized by the combination of the rotating motion of the pipe and the reciprocating linear motion of the polishing head. Moreover, a series of comparative experiments are conducted to investigate the polishing mechanism of magnetorheological (MR) fluid and enhance the polishing performance. It is shown from the experimental results that proposed VMRP approach exhibits the better polishing performance than the conventional horizontal MR polishing method under same testing conditions. This is because the proposed VMRP method well eliminates the traces of polishing particles owing to the combination of polishing particles with different sizes. In addition, it is identified from the experimental test that the polishing time of the VMRP required to achieve the same polishing effect as the conventional method is shortened under the combination of different rotation speeds. It is identified from the above benefits of the VMRP that the final surface roughness after polishing is below 0.05 μm.

Under the extreme shortage of water resources in the Yellow River Basin, it is of great signifi-cance to analyze the spatial distribution relationship between rural settlement and water re-sources for the coordinated development of human and water resources in the Yellow River Ba-sin. However, the water allocation scheme depended on statistical data in the previous work, not on rural settlements in space. Furthermore, previous researches seldom focus on the evaluation of surface water resources accessibility according to the spatial distribution characteristics of ru-ral settlements and water resources, especially, in the Yellow River Basin and using rural set-tlement as unit. Therefore, a quantitative evaluation model of surface water resources accessibil-ity is constructed by using the GIS network analysis method, taking rural settlement as the re-search unit, based on three dimensions of topography, distance, and surface water resources, at the Yellow River basin scale. The results show that: (1) The surface runoff of rural settlement in the Yellow River basin is mostly less than 0.05 km/m2, reaching 99.83%. In other words, the Yel-low River Basin is extremely short of water resources. The surface water resources accessibility is affected by distance, topography, and surface water resources. The evaluation results show that the range of surface water resources accessibility is 0.13~0.88, with an average value of 0.47 and a standard deviation of 0.05. The High surface water resources accessibility value in the Yel-low River Basin is in the east and west, and the low value is mainly distributed in the middle. (2) The range from low to high of surface water resources accessibility in 12 catchments is Sanmen-xia station, Lanzhou station, Shizuishan station, Longmen station, Tongguan station, Toudaoguai station, Xiaolangdi station, Huayuankou station, Lijin station, Gaocun station, Ai Shan station and Tangnaihai station. (3) The value of surface water resources accessibility at the city scale is higher in the east of 10 cities and in the west of 1 city. However, it is lower in the west of 9 cities. And the values of the other cities are at a medium level. The correlation coefficient with primary industry GDP and surface water resources accessibility is 0.271 (N=56, Sig=0.043, in 0.05 level, the correlation is significant), which verifies the rationality of surface water resources accessibility model to some extent.

The effect of graphene (GR) on Ni surface relaxation and reconstruction in three different substrate orientations: {111}, {001}, {011}, at two different temperatures: 300K and 400K was studied using Molecular Dynamics simulation. The change of the interplanar distances of the substrate and redistribution of Ni and C atoms in direction perpendicular to the surface were compared with the equilibrium state of GR and bulk Ni, in the absence of the counterpart. The surface reconstruction for GR/Ni system was analyzed base on the calculated radial pair distribution function of Ni and C atoms. The surface roughness was visualized using 2D atomic distribution maps. For the studied substrate orientations and temperatures, it was found that the most densely packed orientation of the Ni base {111} provides minimal changes of the structural parameters of both counterparts at 400 K.

Anion exchange of the halides, Br and I, is demonstrated through the direct mixing of two pure perovskite quantum dot solutions, CsPbBr3 and CsPbI3, and is shown to be both facile and result in a completely alloyed single phase mixed halide perovskite. Anion exchange is also observed in an interlayer printing method utilizing the pure, unalloyed perovskite solutions and a commercial inkjet printer. The halide exchange was confirmed by optical absorption spectroscopy, photoluminescent spectroscopy, X-ray diffraction, and X-ray photoemission spectroscopy characterization, and indicates that alloying is thermodynamically favorable, while the formation of a clustered alloy is not favored. Additionally, a surface-to-bulk photoemission core level transition is observed for the Cs 4d photoemission feature which indicates the electronic structure of the surface is different from the bulk. Time resolved photoluminescence spectroscopy indicates the presence of multiple excitonic decay features which is argued to originate from states residing at surface and bulk environments.

The catenary shells of revolution are widely used in constructions due to their unique mechanics' feature. However, no publications on this type of shells can be found in the literature. To have a better understanding of the deformation and stress of the catenary shells of revolution, we formulate the principal radii for two kinds of catenary shells of revolution and their displacement type governing equations. Numerical simulations are carried out based on both Reissner-Meissner mixed formulations and displacement formulations. Our investigations show that both deformation and stress response of elastic catenary shells of revolution are sensitive to its geometric parameter $c$, and reveal that the mechanics of the catenary shells of revolution does much better than the spherical shells. Two complete codes in Maple are provided.

The land-surface developments of the European Centre for Medium-range Weather Forecasts (ECMWF) are based on the Carbon-Hydrology Tiled Scheme for Surface Exchanges over Land (CHTESSEL) and form an integral part of the Integrated Forecasting System (IFS), supporting a wide range of global weather, climate and environmental applications. In order to structure, coordinate and focus future developments and benefit from international collaboration in new areas, a flexible system named ECLand which would facilitates modular extensions to support numerical weather prediction (NWP) and society-relevant operational services, e.g. Copernicus, is presented . This paper introduces recent examples of novel ECLand developments on (i) vegetation, (ii) snow, (iii) soil, (iv) open water/lake (v) river/inundation, and (vi) urban areas. The developments are evaluated separately with long-range, atmosphere-forced surface offline simulations, and coupled land-atmosphere-ocean experiments. This illustrates the benchmark criteria for assessing both, process fidelity with regards to land surface fluxes and reservoirs of the water-energy-carbon exchange on the one hand, and on the other hand the requirements of ECMWF’s NWP, climate and atmospheric composition monitoring services using an Earth system assimilation prediction framework.

This paper proposes the use of non-uniform extended surfaces installed externally to the tubes of the radiation section of fired heaters, in order to obtain a better heat flux distribution to the coils. To this end, the heat transfer mechanisms present in such equipment were studied through computational fluid dynamics (CFD), using simplified geometries that represent typical sizes of fired heaters. Also, a simplified model for the combustion was considered. Although this model oversimplifies the physics of the problem, it was able to give satisfactory results for the parameters being optimized, considering the main objective of this paper, that is to minimize the non-uniformity of heat flux in the tubes of the radiant section of fired heaters. It was possible to obtain optimized geometric parameters for different types of extended surfaces evaluated, coupling the results of these models with the Particle Swarm optimization method through the use of a response surface technique,. The results indicate a significant improvement in the uniformity of the heat flux distribution to the tubes through the use of the proposed extended surfaces. Thus, this solution reveals to be an interesting alternative to reduce the risks of fluid degradation and coking formation. Future studies must investigate the non-uniformity of the heat flux due to the presence of the flame and consider the interaction between the reactive flow and the participating medium. Nevertheless, this paper presents some results that justify the optimization of such extended surfaces taking into consideration thermal radiation.

Surface urban heat island (SUHI) depicts the deteriorating thermal environment in high-density cities and local climate zone (LCZ) classification provides a universal protocol for SUHI identification. In this study, taking the central urbanized area of Guangzhou in the humid subtropical region of China as the study area, the maps or images of LCZ, land surface temperature (LST), SUHI and urban design factors were achieved by using Landsat satellite data, GIS database and a series of retrieval and classification algorithms, and the urban design factors influencing SUHI were investigated based on 625 samples of LCZs. The results show that in the summer daytime under the clear sky condition, the LST varied greatly from 26 °C to 40 °C and the SUHI changed in a wide range of -6 °C to 8 °C in the LCZs of the study area. Seven and five urban design factors influencing the summer daytime SUHI were identified for the two dominant LCZ of LCZs 1-5 (LCZ 1 to LCZ 5) and the mixed LCZ (containing at least three types of LCZs), respectively. The summer daytime SUHI prediction models were obtained by using the step-wise multiple linear regression, with the performance of R2 of 0.697, RMSE of 1.21 °C, and the d value of 0.81 for the model of LCZs 1-5, and the values of 0.666, 1.66 °C, and 0.76 for the model of the mixed LCZ, indicating that the models can predict the changes of SUHI with LCZs to a large and satisfactory extent. This study presents a methodology to efficiently achieve a large sample of SUHI and urban design factors of LCZs in the largely urbanized cities, and provides information beneficial to the urban designs and regenerations in the humid subtropical region.

Surface damage on honeycomb aircraft panels is often measured manually, and is therefore subject to variation based on inspection personnel. Eddy current testing (ECT) is sensitive to variations in probe-to-specimen spacing, or lift-off, and is thus promising for high resolution profiling of surface damage on aluminum panels. Lower frequency testing also allows inspection through the face sheet, an advantage over optical 3D scanning methods. This paper presents results from the ECT inspection of surface damage on an approximately flat aluminum honeycomb aircraft panel, and compares the measurements to those taken using optical 3D scanning technology. An ECT C-Scan of the dented panel surface was obtained by attaching the probe to a robotic scanning apparatus. Data was taken simultaneously at four frequencies of 25, 100, 400 and 1,600 kHz. A reference surface was then defined that approximated the original, undamaged panel surface, which also compensated for the effects of specimen tilt and thermal drift within the ECT instrument. Data was converted to lift-off using height calibration curves developed for each probe frequency. A damage region of 22,550 mm² area with dents ranging in depth from 0.13-1.01 mm was analyzed. The method was accurate at 1,600 kHz to within 0.05 mm (2s) when compared with 231 measurements taken via optical 3D scanning. Testing at 25 kHz revealed a 3.2 mm cell size within the honeycomb core, which was confirmed via destructive evaluation. As a result, ECT demonstrates potential for implementation as a method for rapid in-field aircraft panel surface damage assessment.

The article addresses the development and evaluation of a novel environmentally-friendly cutting fluid prepared using sunflower oil and ZnO nanoparticles, specifically developed for use in metal machining processes. An experimental investigation was conducted to examine the impact of three adjustable input process factors: spindle speed, feed rate, and depth of cut on Mild steel. The investigation was carried out under two conditions: one with a 1%(weight) ZnO nano cutting fluid and the other with a 1.5%(weight) ZnO nano cutting fluid. The study focused on two factors: surface roughness and material removal rate (MRR), which were measured during the process of face-milling mild steel. The research aims to optimize the milling machine settings to improve the efficiency of machining mild steel as the work material. This will be achieved by using Response Surface Methodology (RSM). The ZnO nano-cutting fluid was created using a meticulous technique and its stability was assessed by several investigations. An investigation indicates that a ZnO nano-cutting fluid with a weight concentration of 1.5% is more stable. The process was enhanced by the use of a newly created integrated approach grounded on response surface methodology (RSM). The suitability of the model was confirmed by an analysis of variance (ANOVA). The analysis revealed that, when considering equal weights of responses, the ideal values for the input parameters of spindle speed, feed rate, and depth of cut were determined to be 408.081 rpm, 146.667 m/min, and 0.4878 mm accordingly, under the circumstances of using 1.5% weight of ZnO nano cutting fluid. The projected output responses were as follows: 777.920 for the MRR (Material Removal Rate) and 3.5297 for surface roughness. The composite attractiveness was calculated to be 0.61433. The suggested model in this research shows a fitting of over 80% with our studied values. This model may be used to discover the ideal states and enhance the efficiency of the milling process. The enhanced milling parameters exhibit the potential to enhance machining performance, offering useful insights for firms seeking environmentally sustainable alternatives for metal-cutting operations. This work contributes to the advancement of sustainable machining practices by developing a novel formulation for cutting fluid and providing a systematic approach to improving machining parameters.

XPS and ARXPS characterization of surface layers resulting from the functionalization of polymers such as PVC modified with MPTMS and APTES is challenging due to the signals overlap, deriving both from the substrate and the functionalized layers. In this work, a freshly cleaved, ideally flat gold surface was used as carbon-free model substrate functionalized with MPTMS and subsequently grafted with APTES. Avoiding the overlap of signals from carbon atoms present in the substrate, the signals in the C1s, O1s, Si2p, S2p and N1s high-resolution spectra could be assigned to the MPTMS / APTES functionalized layer only and the curve fitting parameters could be determined. Quantitative analysis was in very good agreement with the expected stoichiometry of the functionalized layer, confirming the adopted curve fitting procedure. In addition, it was found that one molecule of APTES grafted two MPTMS via silane groups. ARXPS allowed determining the thickness of the functionalized layers: MPTMS thickness was found to be 0.5 (0.2) nm, MPTMS + APTES thickness 1.0 (0.2) nm in good agreement with Avogadro model calculations. This approach can be considered a powerful tool for characterising functionalized surfaces of more complex systems by XPS.

Laser-induced periodic surface structures (LIPSS) have gained significant attention due to their ability to modify the surface morphology of materials at the micro-nanoscale and show great promise for surface functionalization application. In this study, we specifically investigate the formation of LIPSS in silicon substrates and explore their impact on Surface-Enhanced Raman Spectroscopy (SERS) applications. This study reveals a stepwise progression of LIPSS formation in silicon, involving three distinct stages of LIPSS: 1) integrated Low-Spatial-Frequency LIPSS (LSFL) and High-Spatial-Frequency LIPSS (HSFL), 2) principally LSFL and 3) LSFL at the edge of the irradiated spot, elucidating the complex interplay between laser fluence, pulse number, and resulting surface morphology. Furthermore, from an application standpoint, these high-quality multi-scale periodic patterns lead to the next step of texturing the entire silicon surface with homogeneous LIPSS for SERS application. The potential of LIPSS-fabricated silicon substrates for enhancing SERS performance is investigated using thiophenol as a test molecule. The results indicate that the Au-coated combination of LSFL and HSFL substrate showcased the highest enhancement factor (EF) of 1.38 × 10^6. This pronounced enhancement is attributed to the synergistic effects of Localized Surface Plasmon Resonance (LSPR) and Surface Plasmon Polaritons (SPPs), intricately linked to HSFL and LSFL characteristics. These findings contribute to understanding LIPSS formation in silicon and their applications in surface functionalization and SERS, paving the way for sensing platforms.

We investigated the effect of helium atmospheric-pressure plasma (PL) and deep-ultraviolet (UV) light treatments on the adhesive properties of fiber-reinforced poly(ether-ether-ketone)polymer (PEEK). PEEK disks reinforced with carbon (CPEEK) or glass (GPEEK) fibers were polished, modified with PL and UV for 60 s, and the surface energy was calculated by measuring the contact angles. The disk surfaces were analyzed by X-ray photoemission spectroscopy. Shear bond strength testing was performed using a universal testing machine, and the fracture surfaces were observed by electron probe microanalyzer. Data were analyzed with one and two-way ANOVA and Tukey’s post-hoc test (p < 0.05). The surface energies were increased by the modifications, which created OH functional groups on the surfaces. The bond strengths of CPEEK were increased by PL and those of GPEEK were increased by PL and UV, owing to chemical bonding at the interface.

Traditional ways of validating satellite-derived sea surface temperature (SST) and sea surface salinity (SSS) products, using comparisons with buoy measurements, do not allow for evaluating the impact of mesoscale to submesoscale variability. Here we present the validation of remotely-sensed SST and SSS data against the unmanned surface vehicle (USV) – Saildrone – measurements from the Spring 2018 Baja deployment. More specifically, biases and root mean square differences (RMSD) were calculated between USV-derived SST and SSS values, and six satellite-derived SST (MUR, OSTIA, CMC, K10, REMSS, and DMI) and three SSS (JPLSMAP, RSS40, RSS70) products. Biases between the USV SST and OSTIA/CMC/DMI were approximately zero while MUR showed a bias of 0.2C. OSTIA showed the smallest RMSD of 0.36C while DMI had the largest RMSD of 0.5C. An RMSD of 0.4C between Saildrone SST and the satellite-derived products could be explained by the daily variability in USV SST which currently cannot be resolved by remote sensing measurements. For SSS, values from the JPLSMAP product showed saltier biases of 0.2 PSU, while RSS40 and RSS70 showed fresh biases of 0.3 PSU. An RMSD of 0.4 PSU could not be explained solely by the daily variability of the USV-derived SSS. Coherences were significant at the longer wavelengths, with a local maximum at 100 km that is most likely associated with the mesoscale turbulence in the California Current System.

This study aims to assess the potential of the LDAS-Monde a land data assimilation system developed by Météo-France to monitor the impact of the 2018 summer heatwave over western Europe vegetation state. The LDAS-Monde is forced by the ECMWF’s (i) ERA5 reanalysis, and (ii) the Integrated Forecasting System High Resolution operational analysis (IFS-HRES), used in conjunction with the assimilation of Copernicus Global Land Service (CGLS) satellite derived products, namely the Surface Soil Moisture (SSM) and the Leaf Area Index (LAI). Analysis of long time series of satellite derived CGLS LAI (2000-2018) and SSM (2008-2018) highlights marked negative anomalies for July 2018 affecting large areas of North Western Europe and reflects the impact of the heatwave. Such large anomalies spreading over a large part of the considered domain have never been observed in the LAI product over this 18-yr period. The LDAS-Monde land surface reanalyses were produced at spatial resolutions of 0.25°x0.25° (January 2008 to October 2018) and 0.10°x0.10° (April 2016 to December 2018). Both configuration of the LDAS-Monde forced by either ERA5 or HRES capture well the vegetation state in general and for this specific event, with HRES configuration exhibiting better monitoring skills than ERA5 configuration. The consistency of ERA5 and IFS HRES driven simulations over the common period (April 2016 to October 2018) allowed to disentangle and appreciate the origin of improvements observed between the ERA5 and HRES. Another experiment, down-scaling ERA5 to HRES spatial resolutions, was performed. Results suggest that land surface spatial resolution is key (e.g. associated to a better representation of the land cover, topography) and using HRES forcing still enhance the skill. While there are advantages in using HRES, there is added value in down-scaling ERA5, which can provide consistent, long term, high resolution land reanalysis. If the improvement from LDAS-Monde analysis on control variables (soil moisture from layers 2 to 8 of the model representing the first meter of soil and LAI) from the assimilation of SSM and LAI was expected, other model variables benefit from the assimilation through biophysical processes and feedbacks in the model. Finally, we also found added value of initializing 8-day land surface HRES driven forecasts from LDAS-Monde analysis when compared with model only initial conditions.

In urban area, one of the great problem is the rise of temperature, which leads to form the urban heat island effect. This paper refers to the trend of the urban surface temperature extracted from the Landsat images from which to consider changes in the formation of surface urban heat island for the north of Ho Chi Minh city in period 1995-2015. Research has identified land surface temperature from thermal infrared band, according to the ability of the surface emission based on characteristics of normalized difference vegetation index NDVI. The results showed that temperature fluctuated over the city with a growing trend and the gradual expansion of the area of the high-temperature zone towards the suburbs. Within 20 years, the trend of the formation of surface urban heat island with two typical locations showed a clear difference between the surface temperature of urban areas and rural areas with space expansion of heat island in 4 times in 2015 compared to 1995. An extreme heat island located in the inner city has an area of approximately 18% compared to the total area of the region. Since then, the solution to reduce the impact of urban heat island has been proposed, in order to protect the urban environment and the lives of residents in Ho Chi Minh City becoming better

Researchers have explored primary colour-geometric shape associations since Kandinsky's correspondence theory. However, there is a gap in the literature regarding interior colour applications on surface shapes. To address this gap, an online study was employed to gather data with one hundred participants who were asked to choose their preferred colours for shapes on bedroom walls with follow-up questions on the colour-shape semantic associations, their preference of colours and shapes on bedroom walls independently in addition to their favourite colour, their favourite shape, and colour-shape pairs without interior context. The results revealed that colour-shape preferences in interiors differ from those found in psychology studies, other colour applications on bedroom walls, and other preferences, indicating that colour preference is context-dependent. Interestingly, the most popular colour for surface shapes on bedroom walls is purple, followed by brown and blue. The study contributes to the existing literature by providing colour charts for bedroom applications for professionals in the industry, their clients/users, and future studies.

Silicon carbide single crystal (SiC) has been widely used in the field of power devices, while it is difficult to fabricate ultra-flat surface by traditional manufacturing technologies due to its difficult-to-machine property. This paper investigates the interaction process during femtosecond laser ablation of crystalline silicon carbide based on the two-temperature model simulation and experimental study. The findings reveal that parameters such as laser pulse energy, scanning interval, and defocus amount exert significant influence on ablation depth, roughness, and surface morphology. The femtosecond laser proves effective in removing surface defects from cut SiC substrates, albeit resulting in increased surface roughness. However, subsequent polishing treatment of the laser-ablated silicon carbide surface can mitigate this roughness, underscoring the feasibility of laser surface ablation for silicon carbide single crystals.

Shaped surfaces are increasingly used in the field of mould making for casting or injection moulding, where future products include shapes with different curvatures. These are surfaces that form convex curves, concave curves, or a combination thereof. Given these machined surfaces, it is important to know the impact of the finishing strategies on these surfaces. This paper deals with the comparison of finishing milling strategies in the production of shaped surfaces and the analysis of different methods for the evaluation of surface topography, surface roughness and the evaluation of deviations. The material used for the experiments was AlCu4Mg aluminium alloy, and Constant Z, Spiral and Spiral circle strategies were chosen for the finishing strategies. The evaluation of surface topography and surface roughness was carried out at three different sample heights with respect to the tool contact with the machined surface. The results showed changes in the toolpaths due to the variation of the effective diameter of the tool cutter to the machined surface as well as the choice of strategy. To produce specimens with corresponding shapes in terms of topography, the Constant Z strategy was the most suitable, in which uniform toolpaths were obtained over the whole height of the sample.

Three-Dimensional reconstruction of the corneal surface provides a powerful tool for managing corneal diseases. This study proposes a novel method for reconstructing the corneal surface from elevation point clouds, using modal schemes capable of reproducing corneal shapes using surface polynomial functions. The multivariable polynomial fitting was performed using a non-dominated sorting multivariable genetic algorithm (NS-MVGA). Standard reconstruction methods using least-squares discrete fitting (LSQ) and sequential quadratic programming (SQP) were compared with the evolutionary algorithm-based approach. The study included 49 eyes of 49 patients (ages 11-63) sorted in two groups: control (33 eyes) and keratoconus (KC) (16 eyes). Tomographic information (Sirius, Costruzione Strumenti Oftalmici, Italy) was processed using Matlab. The goodness of fit for each method was evaluated using mean squared error (MSE), measured at the same nodes where the elevation data were collected. Polynomial fitting based on NS-MVGA improves MSE values by 86% compared to LSQ-based methods in healthy patients. Moreover, this new method improves aberrated surface reconstruction by 43% for Amsler-Krumeich (AK) Grade 1 keratoconus patients. Finally, significant improvements were also found in morpho-geometric parameters, such as asphericity and corneal curvature radii.

We present a numerical illumination model to calculate direct as well as diffuse or Hapke scattered radiation scenarios on arbitrary planetary surfaces. This includes small body surfaces such as main belt asteroids as well as e.g. the lunar surface. The model is based on the raytracing method. This method is not restricted to spherical or ellipsiodal shapes but digital terrain data of arbitrary spatial resolution can be fed into the model. Solar radiation is the source of direct radiation, wavelength-dependent effects (e.g. albedo) can be accounted for. Mutual illumination of individual bodies in implemented (e.g. in binary or multiple systems) as well as self-illumination (e.g. crater floors by crater walls) by diffuse or Hapke radiation. The model is validated by statistical methods. A χ2 test is undertaken to compare simnulated images with DAWN images acquired during the survey phase at small body 4 Vesta.

The calculation of the surface tension of ordinary organic and ionic liquids, based on a computer algorithm applying a refined group-additivity method, is presented. The refinement consists of a complete breakdown of the molecules into their constituting atoms, further distinguishing them by their immediate neighbour atoms and bond constitution. The evaluation of the atom-groups’ contributions was carried out by means of a fast Gauss-Seidel fitting method founded upon the experimental data of 1895 compounds from literature. The result has been tested for plausibility using a 10-fold cross-validation (cv) procedure. The direct calculation and the cv test proved the applicability of the present method by the close similarity and excellent goodness of fit R2 and Q2 of 0.9023 and 0.8821, respectively. The respective standard deviations are ±2.01 and ±2.16 dyn/cm. Some correlation peculiarities have been observed in a series of ordinary and ionic liquids with homologous alkyl chains which are illustrated and discussed in detail, exhibiting the limit of the present method.

Inverse gas chromatography at infinite dilution was used to determine the surface thermodynamic properties of silica particles and PMMA adsorbed on silica, and more particularly, to quantify the London dispersive energy γsd, the Lewis acid γs+ and base γs- polar surface energies of PMMA/silica composites as a function of the temperature and the recovery fraction θ of PMMA. The polar acid–base surface energy γsAB and the total surface energy of the different composites were then deduced as a function of the temperature. In this paper, the Hamieh thermal model was used to quantify the surface thermodynamic energy of poly methyl methacrylate (PMMA) adsorbed on silica particles at different recovery fractions. A comparison of the new results was carried out with those obtained by applying other molecular models of the surface areas of organic molecules adsorbed on the different solid substrates. An important deviation of these molecular models from the thermal model was proved. The determination of γsd, γs+, γs-, and γsAB of PMMA in both bulk and adsorbed phases showed an important non-linearity variation of these surface parameters as a function of the temperature. The presence of maxima in the curves of γsd(T) highlighted the second order transition temperatures in PMMA showing beta-relaxation, glass transition and liquid-liquid temperatures. These three transition temperatures depended on the adsorption rate of PMMA on silica. The proposed method gave a new relation between the recovery fraction of PMMA and its London dispersive energy showing an important effect of the temperature on the surface energy parameters of adsorption of PMMA on silica. A universal equation relating γsd(T,θ) of the systems PMMA/silica to the recovery fraction and the temperature was proposed.

This comprehensive review explores recent advancements in heavy metal remediation techniques, focusing on the utilization of cellulose-silica composites and tailored surface modification techniques. We examine the synthesis strategies and properties of cellulose-silica adsorbents, highlighting their enhanced adsorption capacities and structural robustness for removing heavy metal pollutants from aqueous environments. The review investigates various surface modification approaches, including thiol-functionalization, amino acid grafting, and silane coupling agents, for optimizing the surface chemistry and morphology of cellulose-silica composites. Mechanistic insights into the adsorption processes and kinetics of modified adsorbents are discussed, along with considerations for optimizing adsorption performance under different environmental conditions. This review provides valuable perspectives on the development of effective adsorbent materials for sustainable heavy metal remediation applications.

We present a modified characteristic finite element method that exhibits second-order spatial accuracy for solving convection-reaction-diffusion equations on surfaces. The temporal direction adopted backward-Euler method, while the spatial direction employed surface finite element method. In contrast to regular domains, it is observed that the point in the characteristic direction traverses the surface only once within a brief time. Thus, the good approximation of the solution in the characteristic direction holds significant importance for the numerical scheme. In this regard, Taylor expansion is employed to reconstruct the solution beyond the surface in the characteristic direction. The stability of our scheme is then proved. A comparison is made with an existing characteristic finite element method based on face mesh. Numerical examples are provided to validate the effectiveness of our proposed method.

AISI 1050 steel circular pocket milling under minimum quantity lubrication (MQL) surroundings including nozzle elevation angle, lubricant flow rate, air pressure and cutting speed was studied. The machined surface quality (Ra) was evaluated for Up-milling side and Down-milling side. In this study, to obtain an manifest explanation on the pivotal effective parameters of MQL surroundings and cutting speed on the machined surface quality (Ra) through analyzing Taguchi L9 (34-2) approach and ANOVA calculation to identify those parameters, by utilizing the experimental outcomes to interpret three-dimensional (3D) surface plots and the diagrams of Signal-to-Noise ratios and major impact plots of Mean. The obtained outcomes of optimal operating parameters indicated that the pivotal effective parameters of MQL surroundings are nozzle elevation angle and lubricant flow rate on the machined surface quality. Simultaneously, a quadratic mathematical paradigm generated by using response surface design (RSD) and desirableness function evaluation were utilized to forecast the optimal values of the machined surface quality compared to Taguchi method. The results unveiled that the optimal values of the machined surface quality are adjacent to experimental attained values. The machined surface quality has been significantly improved using MQL surroundings.

In this study, an investigation on the influence of In-situ tribo-oxide-layer on non-lubricated tribological behaviours of LM27/SiCp composites was carried out at different applied loads. The variations in wear performance and microstructure of brake lining friction material (LM27) with the addition of different amounts and sizes of SiCp are explored. For this purpose, LM27/SiCp composite materials were manufactured by stir casting route varying the amount of particle reinforced from 3wt.% to 12wt.% with a different size range (fine: 1-20µm and coarse: 106-125µm). Non-lubricated dry wear tests of LM27/SiCp composites samples were trialled at different loads from 9.8N to 49N by using a pin-on-disc machine system. At a contact pressure of 0.2-1 MPa, LM27/SiCp composites with 12wt.% reinforcement showed a lower coefficient of friction than other composites. In-situ formation of oxide layers on the contact region of the specimen supports the self-lubrication during the wear test, which is responsible for better wear performance of LM27/SiCp composites. However, these study portraits that composite with 12wt. % fine size SiCp exhibits better wear performance in comparison to the other developed composites.

Nobel metal nanohole arrays have been used extensively in chemical and biological systems due to their fascinating optical properties. Gold nanohole arrays (Au NHAs) were prepared as surface plasmon polaritons (SPP) generators for the surface-enhanced sum-frequency generation (SFG) detection of 4-Mercaptobenzonitrile (4-MBN). The angle-resolved reflectance spectra revealed that the Au NHAs have three angle-dependent SPP modes and two non-dispersive localized surface plasmon resonance (LSPR) modes under different structural orientation angles (sample surface orientation). An enhancement factor of ~30 was achieved when the SPP and LSPR modes of the Au NHAs were tuned to match the incident visible (VIS) and output SFG, respectively. This multi-mode matching strategy provided flexible controls and selective spectral windows for surface-enhanced measurements, and was especially useful in nonlinear spectroscopy where more than one light beam involved. The structural orientation- and power-dependent performance demonstrated the potential of plasmonic NHAs in SFG and other nonlinear sensing applications, and provided a promising surface molecular analysis development platform.

Dispersed silver nanoparticles (AgNPs) on the surface of titanium alloy (Ti6Al4V) and titanium alloy modified by titania nanotube layer (Ti6Al4V/TNT) substrates were produced by chemical vapor deposition method (CVD) using novel precursor of the formula [Ag₅(O₂CC₂F₅)₅(H₂O)₃]. The structure and volatile properties of this compound were determined using single crystal X-ray diffractometry, variable temperature IR spectrophotometry (VT IR), and electron inducted mass spectrometry (EI MS). The morphology and the structure of the produced Ti6Al4V/AgNPs, and Ti6Al4V/TNT/AgNPs composites were characterized by scanning electron microscopy (SEM) and atomic force microscopy (AFM). Moreover, measurements of hardness, Young’s modulus, adhesion, and surface free energy have been carried out. The ability to release silver ions from the surface of produced nanocomposite materials immersed in PBS solution has been estimated using inductively coupled plasma mass spectrometry (ICP MS). The wettability and the surface free energy of samples were estimated on the base of contact angle studies with the use of water and diiodomethane. Among the studied surface-modified titanium alloy implants, the best nano-mechanical properties were noticed for the Ti6Al4V/TNT15/AgNPs composite. The location of silver nanoparticles inside of titania nanotubes caused their lowest release rate, which may indicate on suitable properties above mentioned type of the composite for the construction of implants with a long term of antimicrobial activity.

In this study, the values of the interfacial energies of seven different polymer-water systems obtained by Sessile Drop Accelerometry (SDACC) are compared with the values obtained by the Young’s-equation-based Owens-Wendt method. The SDACC laboratory instrument –a combination of a drop shape analyzer with high-speed camera and a microgravity tower- and the evaluation algorithms, are designed to measure the interfacial energies as a function of the geometrical changes of a sessile droplet shape due to the effect of “switching off” gravity during the experiment. The method bases on Thermodynamics of Interfaces and differs from the conventional aproach of the two hundred-years-old Young’s equation in that it assumes a thermodynamic equilibrium between interfaces, rather than a balance of forces on a point of the solid-liquid-gas contour line. A comparison of the mathematical model that supports the SDACC method with the widely accepted Young`s equation is discussed in detail in this study.

A new method, the sessile drop accelerometry (SDACC) for the study and measurement of the interfacial energies of solid-liquid-gas systems, is tested and discussed in this study. The laboratory instrument and technique –a combination of a drop shape analyzer with high-speed camera and a laboratory drop tower- and the evaluation algorithms, were designed to calculate the interfacial energies as a function of the geometrical changes of a sessile droplet shape due to the effect of “switching off” gravity during the experiment. The method bases on the thermodynamic equilibrium of the system interfaces and not on the balance of bi-dimensional tensions on the solid-liquid-gas contour line. A comparison of the mathematical model that supports the method with the widely accepted Young`s equation is discussed in this study.

Strata and surface movement induced by mining under open-pit final slope is a huge threat to mine safety. Physical model test is an important method to study mining-induced strata and surface movement laws. Because of rock joints predominantly control rock mass deformation and failure, thus physical model test leaving out of consideration of rock joints is difficult to reflect the influence of rock joints on rock mass deformation. Therefore, this paper presents a three-dimensional physical model test considering simplified dominant rock joints. This test process includes the design of testing equipment, the construction of physical model with dominant rock joint sets, conduction of mining and deformation monitoring. And mining under eastern final slope of Yanqianshan iron mine was selected as a case to study the behavior of mining-induced strata and surface movement.

The connection between a prefabricated reinforced concrete column and a pocket foundation is a case treated from a general perspective in the European Standard named EN 1992-1-1, and when the structural engineer deals with the dimensioning or verification of the connection, he tackles several unknowns. The present work aims to fill in the missing information by presenting detailed calculation models based on the strut-and-tie method for 4 of the widely used pocket foundations: pedestal pocket foundation with smooth, rough or keyed internal walls, and pad foundation with pocket possessing keyed internal walls. Additionally, detailed design prescriptions applicable to seismic areas are given. Afterwards, as a case study, a pocket foundation is designed in all 4 variations, having the structural design particularities, similitudes and differences pointed out. Finally, to conclude the advantages and disadvantages are mentioned for pocket foundations in respect to the type of internal wall surface used. Quantifiable data based on the case study undertaken is available.

This paper constitutes an original and new methodology for the determination of the surface properties of carbon fibers in the two oxidized and untreated forms by inverse gas chromatography technique at infinite dilution based on the effect of the temperature on the surface area of the various organic molecules adsorbed on the carbon fibers. The studied thermal effect proved a large deviation of the classical methods or models relative to the new determination of the surface properties of carbon fibers, such as the dispersive component of their surface energy, the free surface energy, the free specific energy, the enthalpy and entropy of adsorption of molecules on the carbon fibers. The obtained specific enthalpy and entropy of adsorption for the polar solvents led to the determination of the Lewis’s acid-base constants of carbon fibers. Different molecular models and chromatographic methods were used to quantify the surface thermodynamic properties of carbon fibers and compared to the thermal model. The obtained results proved that the oxidized carbon fibers gave more specific interaction energy and greater acid-base constants than that of the untreated carbon fibers and thus highlighting the important role of the oxidization on the acid-base of fibers. The determination of the specific acid-base surface energy of the two carbon fibers showed greater values of the oxidized carbon fibers relative to the untreated carbon fibers. An important basic character was highlighted for the two studied carbon fibers, larger than the acidic character. It was observed that the Lewis’s acid-base constants of the oxidized carbon fibers are larger than that of the untreated fibers with more accentuated basic charterer. This result was confirmed by all molecular models and chromatographic methods.

Robot workpiece machining is interesting in industry since it offers some advantages, such as higher flexibility in comparison with the conventional approach based on the CNC technology. However, in recent years we have been facing a strong progressive shift to custom based manufacturing and low volume/high mix production, which require a novel approach to automation by the employment of collaborative robotics. However, collaborative robots feature only limited motion capability, to provide safety in cooperation with human workers. Thus, it is highly necessary to perform more detailed robot task planning to ensure its feasibility and optimal performance. In this paper, we deal with the problem of studying kinematic robot performance in the case of such manufacturing tasks, where the robot tool is constrained to follow the machining path embedded on the workpiece surface at a prescribed orientation. The presented approach is based on the well-known concept of manipulability, although the latter suffers from physical inconsistency due to mixing different units of linear and angular velocity in a general 6 DOF task case. Therefore, we introduce the characteristics of the workpiece surface constraint in the robot kinematic analysis, that enables evaluation of its available velocity capability in a reduced dimension space. Such constrained robot kinematics transform the robot`s task space to a two-dimensional surface tangent plane, and the manipulability analysis may be limited to the space of linear velocity only. Thus, the problem of physical inconsistency is avoided effectively. We show the theoretical derivation of the proposed method, which was verified by numerical experiments.

The performance and lifespan of cutting tools are significantly influenced by their surface quality. The present report highlights recent advances in enhancing the surface characteristics of tungsten carbide and high-speed steel cutting tools using a novel micro-machining technique for polishing and edge-honing. Notably, the main aim is to reduce the surface roughness while maintaining the hardness of the materials at an optimal level. By conducting a thorough analysis, of surfaces obtained with different techniques. It was that micro-machining method effectively decreased the surface roughness of the cutting tools, most effectively of the techniques investigated. Significantly, the surface roughness is reduced from an initial measurement of 400 nm to an impressive value of 60 nm. No significant change in hardness was observed, which guarantees the maintenance of the mechanical properties of the cutting tools. This analysis enhances the comprehension of surface enhancement methodologies for cutting tools through the presentation of these findings. The observed decrease in surface roughness, along with the consistent hardness, exhibits potential for improving tool performance. These enhancements possess the capacity to optimise manufacturing processes, increase tool reliability, and minimise waste generation.

Eastern boundary upwelling systems feature strong zonal gradients of physical and biological ocean properties between cool, productive coastal oceans and warm, oligotrophic subtropical gyres. Zonal currents and jets (striations) are therefore likely to contribute to the transport of water properties between coastal and open oceanic regions. Multi-sensor satellite data are used to characterize the signatures of striations in sea surface temperature (SST), salinity (SSS), and chlorophyll-a (Chl-a) in subtropical eastern North/South Pacific (ENP/ESP) upwelling systems. In the ENP, tracers exhibit striated patterns extending up to ~2500 km offshore. Striations in SST and SSS are highly correlated with quasi-zonal jets, suggesting that these jets contribute to SST/SSS mesoscale patterns via zonal advection. Chl-a striations are collocated with sea surface height (SSH) bands, a possible result of mesoscale eddy trains trapping nutrients and forming striated signals. In the ESP, striations are only found in SST and coincide with SSH bands, consistently with quasi-zonal jets located outside major zonal tracer gradients. An interplay between large-scale SST/SSS advection by the quasi-zonal jets, mesoscale SST/SSS advection by the large-scale meridional flow and eddy advection may explain the persistent ENP hydrographic striations. These results underline the importance of quasi-zonal jets for surface tracer structuring at the mesoscale.

Management practices must be developed to improve yam production sustainability. Image-based phenotyping techniques could help developing such practices based on non-destructive analyses of important plant traits. Our objective was to determine the potential of image-based phenotyping methods to assess traits relevant for tuber yield formation in yam grown in glasshouse and field. We took plant and leaf pictures with consumer cameras. We used the numbers of image pixels to derive the shoot biomass and the total leaf surface and calculated the ‘triangular greenness index’ (TGI) which is an indicator of the plant nitrogen (N) nutritional status. Under glasshouse conditions, the number of pixels obtained from nadir view (image taken top down) was positively correlated to the shoot biomass, and the total leaf surface, while the TGI was negatively correlated to the N content of diagnostic leaves. Under field conditions, pictures taken from the nadir view showed an increase in soil surface cover and a decrease in TGI with time. TGI was negatively correlated to SPAD measured on specific leaves but was not correlated to the N content of these leaves. In conclusion, these phenotyping techniques deliver relevant results but need to be further developed and validated for application in yam.

Deformation of the surface of diamagnetic liquid by magnetic field is called the “Moses Effect”. Physics and applications of the direct and inverse Moses effects are reviewed. Experimental techniques enabling visualization of the effects are surveyed. Impact of magnetic field on micro- and macroscopic properties of liquids is addressed. Influence of the surface tension on the shape of the near-surface dip formed in a diamagnetic liquid by magnetic field is reported. Floating of diamagnetic bodies driven by the Moses effect is treated. The effect of the “magnetic memory of water” in its relation to the Moses Effect is discussed. The dynamics of self-healing of near-surface dips due to the Moses Effect is considered.

Extracellular vesicles (EVs) are natural carriers of biomolecules that play a crucial role in cell-to-cell communication and tissue homeostasis under normal and pathological conditions, including inflammatory diseases and cancer. Since the discovery of the pro-regenerative and immune-modulating properties of EVs, EV-based therapeutics have entered clinical trials for conditions such as myocardial infarction and autoimmune diseases, among others. Due to their unique advantages—such as superior bioavailability, substantial packaging capacity, and the ability to traverse biological barriers—EVs are regarded as a promising platform for targeted drug delivery. However, achieving sufficient accumulation of therapeutic agents at the target site necessitates a larger quantity of EVs per dose compared to using EVs as standalone drugs. This challenge can be addressed by administering larger doses of EVs, increasing the drug dosage per administration, or enhancing the selective accumulation of EVs at target cells. In this review, we will discuss methods to improve the isolation and purification of EVs, approaches to enhance cargo packaging—including proteins, RNAs, and small-molecule drugs—and technologies for displaying targeting ligands on the surface of EVs to facilitate improved targeting. Ultimately, this guide can be applied to the development of novel classes of EV-based therapeutics and to overcoming existing technological challenges.

Synopsis Corneal epithelial wavefront error and epithelial thickness variance qualify as highly sensitive and specific biomarkers for epithelial basement membrane dystrophy (EBMD). The biomarkers show a normalization after treatment of EBMD with phototherapeutic keratectomy. Purpose: To gauge the diagnostic value of a novel spectral-domain optical coherence tomography (SD-OCT) based imaging modality for simultaneous morphological (thickness profile) and refractive (optical wavefront) assessment of the corneal epithelial layer in one of the most common but often underdiagnosed corneal dystrophies: epithelial basement membrane dystrophy (EBMD). Methods: In this prospective observational study, a total of 32 eyes of 32 patients diagnosed with EBMD and 32 eyes of 32 healthy control subjects were examined with high-resolution anterior segment SD-OCT (MS-39; CSO, Florence, Italy). Various epithelial thickness and epithelial wavefront derived terms were compared between groups and receiver operating characteristic (ROC) curves were computed to analyze the diagnostic capacity of the respective parameters. A total of 17 of 32 EBMD patients underwent treatment with phototherapeutic keratectomy (PTK) and were followed up for 3 months. Results: Epithelial thickness variance (60.4 ± 56.7 µm versus 7.6 ± 6.1 µm) and interquartile range (11.0±6.9 versus 3.3±1.9 µm) were markedly elevated in EBMD patients as compared with healthy controls (both with p < 0.001). Epithelial wavefront analysis showed a highly statistically significant excess in all examined aberration terms in EBMD patients (all with p < 0.001). Significantly greater areas under the curve (AUC) were yielded by the epithelial wavefront derived parameters (e.g. total epithelial wavefront error: AUC = 0.966; 95% confidence interval (CI) 0.932 – 1) than by the epithelial thickness-derived parameters (e.g., variance: AUC = 0.919; 95% CI 0.848 – 0.990). Conclusion: Corneal epithelial wavefront aberrometry proved valuable as an objective biomarker for EBMD with high sensitivity and specificity. PTK resulted in a reduction of morphological and refractive epithelial irregularities in EBMD.

Bistatic radar experiments have been used to study surface characteristics of extra-terrestrial bodies in the Solar System, including the Moon, Venus, Mars, and Titan. This paper proposes a 3D model to characterize the scattered field of a Gaussian rough surface on an extra-terrestrial body for an orbital bistatic radar configuration. Specifically, this model will investigate how the variability of surface roughness impacts the spectral broadening of the received signal using physical optics approximations and ray tracing on a surface model using a facet approach with Gaussian properties. A linear relationship between spectral broadening of the signal and surface roughness was found. This relationship is in line with results obtained by commonly used analytical models for bistatic radar on planetary surfaces.

Solar energy is one of the most important renewable energy sources for many settings, such as households, solar-powered vehicles, power grid support, etc. However, the amount of solar energy produced is directly proportional to the surface area of the solar panel exposed to the sun rays, and so the challenges arise for the space required to install solar panels in order to get maximum area coverage of sun radiation energy absorption in constricted spaces such as vehicles powered by solar, small residential apartments, etc. The challenge with solar energy is that once a plate is installed, the space under it or above it cannot be used for another solar panel installation. This is due to the fact that the shadow cast by the above solar panel or structure prevents sun rays from reaching the below solar panel. The introduction of flexible solar panels that can take on any shape has given us the opportunity to explore the possibility of maximising solar plate surface area using surface manifold techniques. In this optimisation study, the constraint is that we have a space with fixed dimensions of length, width, and height, and the objective is to maximise the surface area of the panel within the given space dimensions to maximise solar energy absorption. Thus, this paper then proposes curving the panel surface and/or protruding the surfaces of the panel using the concept of a topology surface manifold to maximise the surface area: Protruding panel surface with shapes such as pyramidal, cone, hemisphere, sinusoidal wavy curve, etc. are analysed to check if the panel surface increases at all. The geometrical design result shows that the panel surface can increase by more than 20%. Although this paper only presents concept work and details of experimental design are yet to be performed, it should also be noted that curving surfaces have drawbacks, such as some protruding parts of solar panels when the plate is tilted, not facing the sun directly, which may cast shadows on parts of the solar panel, causing hindrance.

For marine vessels, a propeller shaft system, also known as a propulsion shaft system, is an essential changer in engine torque and propeller thrust. The propeller shaft system is subjected to transverse, longitudinal, and torsional excitations during operation. These sources of excitations originate from alternating thrust generated by the propeller, operation of a propeller in a stern flow field which is non-uniform in time and space, misalignment of components such as shafts, bearings, and keyholes in the assembly, excitations in the form of rotational motion, and the whirling motion of the shafts. These dynamic excitations posed a challenging issue for the integrity and reliability of a marine vehicle. Thus, it is crucial to analyze the dynamic response of the propulsion shaft system. The dynamic analysis of the propulsion shaft system is typically conducted using numerical /analytical models. At present, Finite Element Model (FEM) as a numerical model plays a vital role in analyzing the dynamic response of the structure. The computed response and the modal parameters from the FE model are reliable only if accurate boundary conditions, such as stiffness, can be imposed on the model. However, the numerical FE model deviates from the experimental results because of uncertainties in the stiffness values of the bearings and other connectors. This paper uses the Response Surface Optimization (RSO) technique to estimate the unknown stiffness of the bearings used in the propulsion shaft system. The experimental model of the propeller shaft system is constructed from the steady-state response of the system using the step sine excitation. The natural frequencies and the amplitude of vibrations in the FE model are updated using the parametric RSO technique. The updated model shows that the difference in natural frequencies and vibration amplitude is less than 10% between the optimized and experimental models. Propeller Shaft, Vibrations, Optimization, Response Surface

In this study, Fe-Mo-B based hardfacing electrodes containing different amounts of Mo were coated on an AISI 1020 steel substrate using the electric arc welding method. The findings show that molybdenum is highly effective on the microstructure and minor changes in the coating composition affect the phases and morphological properties. In the hardness tests, an increase of 73% was achieved in the Fe14Mo2B4 based hardfacing coating compared to the base material and a 30% increase compared to the Fe16B4 based coating. The highest macro hardness value was measured as 56.4 HRC and the highest phase hardness was measured as 3228 HV in the FeMo2B2 phase. The lowest wear rate was measured in the Fe14Mo2B2 based coating. The wear rate of the Fe14Mo2B4 based coating was 8.1 times lower than that of the substrate material and 4.7 times lower than that of the Fe16B4 based coating. According to corrosion test results, the highest corrosion resistance was obtained in Fe16B4 based coating. The current density value of the Fe16B4 based coating was measured to be 13.6 times lower than that of the substrate material.

Unmanned aerial vehicles (UAV) thermal imagery offers several advantages in environmental monitoring, as it can provide a low-cost, high-resolution, and flexible solution to measure the temperature of the surface of the land. Limitations related to the maximum load of the drone lead to use of lightweight uncooled thermal cameras whose internal components are not stabilized to a constant temperature. Such cameras suffer from several unwanted effects that contribute to the increase in temperature measurement error from ±0.5 °C in laboratory conditions, to ±5 °C in unstable flight conditions. This article describes a post processing procedure, that reduces the above unwanted effects. It consists of following steps: i) devignetting using single image vignette correction algorithm, ii) georeferencing of images using EXIF data, scale-invariant feature transform (SIFT) stitching, and gradient descent optimisation, and iii) temperature calibration by minimisation of bias between overlapping thermal images using gradient descent optimisation. The solution was tested in several case studies of river areas, where natural water bodies were used as a reference temperature benchmark. In all tests, the precision of the measurements was increased. The root of the mean of the Square of Errors RMSE on average was reduced by 39.0% and Mean of the absolute value of Errors MAE by 40.5%. The proposed algorithm can be called self-calibrating, as in contrast to other known solutions is fully automatic, uses only field data and does not require any calibration equipment or additional operator effort. A Python implementation of the solution is available on GitHub.

Coalescence of nanowires and other three-dimensional structures into continuous film is desirable for growing low dislocation density III-nitride and III-V materials on lattice-mismatched substrates, and interesting from the fundamental viewpoint. Here, we develop a growth model for vertical nanowires which, under rather general assumptions on the solid-like coalescence process within the Kolmogorov crystallization theory, results in a morphological diagram for the asymptotic coverage of a substrate surface. The coverage is presented as a function of two variables, the material collection efficiency on the top nanowire facet a, and the normalized surface diffusion flux of adatoms from the NW sidewalls b. The full coalescence of nanowires is possible only when a=1 regardless of b. At a&gt;1, which is usual for vapor-liquid-solid growth with a catalyst droplet, nanowires can only partly merge but never coalesce into continuous film. These results can be used for predicting and controlling the degree of surface coverage by nanowires and three-dimensional islands by tuning the surface density, droplet size, adatoms diffusivity, and geometry of the initial structures in the vapor-liquid-solid, selective area or self-induced growth processes in different epitaxy techniques.

At the nanoscale, metals exhibit special electrochemical and optical properties, which play an important role in nanobiosensing. In particular, the surface plasmon resonance based on precious metal nanoparticles, as a kind of tag free biosensor technology, has brought high sensitivity, high reliability and convenient operation to the sensor detection. By applying an electrochemical excitation signal on the nano plasma device, modulating its surface electron density and realizing electrochemical coupling surface plasmon resonance, it can effectively complete the joint transmission of electrical signals and optical signals, increase the resonance shift of the spectrum, and further improve the sensitivity of the designed biosensor. In addition, smartphone is playing an increasingly important role in portable mobile sensor detection systems. These systems typically connect sensing devices to smartphone to perceive different types of information, from optical signals to electrochemical signals, providing ideas for the portability and low-cost design of these sensing systems. Among them, electrochemiluminescence, as a special electrochemical coupled optical technology, has good application prospects in mobile sensing detection due to its strong anti-interference ability, which is not affected by background light. In this review, the surface plasmon resonance is introduced from nanoparticles, and its response process is analyzed theoretically. Then, the mechanism and sensing application of electrochemistry coupled surface plasmon resonance and electrochemiluminescence are emphatically introduced. Finally, it extends to the related research of electrochemical coupled optical sensing on mobile detection platforms.

The surface fluorination of polypropylene (PP) was performed using F2 and O2 gas mixtures with different F2 gas proportions at 25 °C and 13.3 kPa for 1 h. The surface roughness of the fluorinated PP samples was approximately 1.5 times higher than that of the untreated sample (5 nm). The Fourier-transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS) results showed that the PP-derived bonds (-C-C- and -CHx) decreased because they were converted into polar groups (-C–O, -CHF-, and -CFx), which increased the surface electronegativity of PP. The variation in the F2 gas proportion in the gas mixture significantly affected the hydrophilicity and surface composition of PP. At F2 gas proportions of <70%, the hydrophilicity of the fluorinated PP samples improved. Notably, the hydrophilic and negatively charged PP surface enhanced the dyeing of the polymer with basic methylene blue (MB). In contrast, at F2 gas proportions of >90%, the PP surface became hydrophobic owing to increased hydrophobic -CF3 bonds. Thus, enhanced PP dyeing can be controlled based on the composition of the F2 and O2 gas mixture.

A highly efficient reduction process of Cr (VI) with biochar was conducted in this paper. The results showed that nearly 100% Cr (VI) was reduced at selected reaction conditions: the dosage of biochar at m (C)/m(Cr) = 3.0, reaction temperature of 90 ℃, reaction time at 60 min and concentration of H2SO4 of 20 g/L, respectively. The reduction kinetics analysis demonstrated that the reduction of Cr (VI) fitted well with the pseudo-first-order model and the apparent activation energy was calculated to 40.24 kJ/mol. Response surface methodology confirmed that all the experimental parameters had positive effect on the reduction of Cr (VI). The influence of each parameter on the reduction process followed the order: dosage of biochar> Concentration of H2SO4 > Reaction Temperature > Reaction Time. This paper provided a versatile strategy for treatment of wastewater containing Cr (VI) and showed a bright tomorrow for wastewater treatment.

Surface Plasmon Resonance (SPR) is an attracting property of certain transition metals when they are synthesized in nano-range giving rise to promising optical applications. However, most SPR and associated applications are limited to the noble metal nanoparticles, which limits their potential due to high production cost. We report surface plasmon resonance in copper-copper oxide core-shell quantum dots synthesized via chemical route studied by using UV-Visible spectrophotometry. Tuning of the plasmonic resonance with respect to the particle diameter is achieved by an inexpensive all chemical route. Photoluminescence measurements also support the data. This size reduction leads to remarkable changes in its optical response as compared to the bulk metal. The results point towards applications of these materials in tunable SPR based biosensors.

Sea ice surface roughness affects ice-atmosphere interactions, serves as an indicator of ice age, shows patterns of ice convergence and divergence, affects the spatial extent of summer melt ponds, and ice albedo. We have developed a method for mapping sea ice surface roughness using angular reflectance data from the Multi-angle Imaging SpectroRadiometer (MISR) and lidar-derived roughness measurements from the Airborne Topographic Mapper (ATM). Using an empirical data modeling approach, we derived estimates of Arctic sea ice roughness ranging from centimeters to decimeters meters within the MISR 275-m pixel size. Using independent ATM data for validation, we find that histograms of lidar and multi-angular roughness values are nearly identical for areas with roughness <20 cm but that for rougher regions, the MISR-derived roughness has a narrower range of values than the ATM data. The algorithm is able to accurately identify areas that transition between smooth and rough ice. Because of its coarser spatial scale, MISR-derived roughness data have a variance of about half that ATM roughness data.

Wetting of deformable substrates has gained significant interest over the past decade due to its extensive applications and uses. This interest has developed due to technological advances which are able to capture interfacial behavior taking place when a liquid droplet is placed on a deformable substrate. Researchers have developed different theories to explain processes taking place in the process of wetting of deformable/soft substrates. For the scope of this review, we will consider the fluid to be Newtonian, partially wetting, and surface forces are incorporated with the help of disjoining/conjoining pressure acting in the vicinity of the apparent, three-phase contact line. The following subjects are briefly reviewed: (i) Equilibrium of droplets on soft substrates. It is shown that properties of the disjoining/conjoining pressure isotherm and properties of the deformable substrate determine both the shape of the liquid droplet and deformation of the substrate; (ii) Equilibrium conditions of droplets on deformable substrates. It is shown that for a droplet to be at equilibrium on a deformable substrate under consideration, Jacobi’s sufficient condition is satisfied; (iii) Hysteresis of contact angle of sessile droplets on deformable substrates. It is shown that as the elasticity of the deformable substrate is increased, both advancing and receding contact angles are reduced.

The influence of the film thickness and the substrate’s refractive index on the surface mode at the superstrate is an important study step that may help clearing some of the misunderstandings surrounding their propagation mechanism. A single sub-wavelength slit perforating a thin metallic film is among the simplest nanostructure capable of launching Surface Plasmon Polaritons on its surrounding surface when excited by an incident field. Here, the impact of the substrate and the film thickness on surface waves is investigated. When the thickness of the film is comparable to its skin depth, SPP waves from the substrate penetrate the film and emerge from the superstrate, creating a superposition of two SPP waves, that leads to a beat interference envelope with well-defined loci which are the function of both the drive frequency and the dielectric constant of the substrate/superstrate. As the film thickness is reduced to the SPP’s penetration depth, surface waves from optically denser dielectric/metal interface would dominate, leading to volume plasmons that propagate inside the film at optical frequencies. Interference of periodic volume charge density with the incident field over the film creates charge bundles that are periodic in space and time.

The aim of the present study was to monitor implant stability after sinus floor elevation with two biomaterials during the first 6 months of healing by a resonance frequency analysis (RFA), and how physico-chemical properties affect the implant stability quotient (ISQ) at the placement and healing sites. Bilateral maxillary sinus augmentation was performed in 10 patients in a split-mouth design using a bobine HA (BBM) as a control and porcine HA (PBM). Six months after sinus lifting, 60 implants were placed in the posterior maxilla. The ISQ was recorded on the day of surgery from RFA at T1 (baseline), T2 (3 months), and T3 (6 months). Statistically significant differences were found in the ISQ values during the evaluation period. The ISQ (baseline) was 63.8±2.97 for BBM and 62.6±2.11 for PBM. The ISQ (T2) was ~ 73.5±4.21 and 67±4.99, respectively. The ISQ (T3) was ~ 74.65±2.93 and 72.9±2.63, respectively. All the used HAs provide osseointegration and statistical increases in the ISQ at baseline, T2 and T3 (follow-up), respectively. The BBM, sintered at high temperature with high crystallinity and low porosity, presented higher stability, which demonstrates that variations in the physico-chemical properties of a bone substitute material clearly influence implant stability.

Analyzing the impacts of urban landscape patterns on the thermal environment has become one of the key research areas in addressing urban heat islands (UHI) and improving the living environment. A case study was carried out in Fuzhou, Fujian Province of China, to quantify the spatial patterns of urban landscape and land surface temperature (LST) in different development areas. The contribution of the thermal environment and the factors influencing the heterogeneity of LST were analyzed and discussed. In this study, bi-temporal Landsat imagery was selected to calculate LST, percent impervious surface area (ISA), and fractional vegetation cover (FVC). The urban area was further divided into three concentric urban zones, ranging from the city center to the urban periphery, based on urban development densities. The spatial pattern of LST and its variance were analyzed and compared between different zones and different dates. The thermal environment contribution of different zones was also quantified to indicate the change in urban landscape pattern resulting from urban expansion in different zones. Furthermore, Geodetector was used to explore the single factors and interaction factors controlling the spatial patterns of LST in each zone. The results showed that (ⅰ) Urban expansion primarily increased in zone 2 and zone 3, and the areal proportion of high and sub-high LST areas increased from 56.11% and 21.08% to 62.03% and 32.49% in zone 2 and zone 3, respectively, from 2004 to 2021; (ⅱ) The heat effect contribution of zones 2 and 3 reached from 75.16% in 2004 to 89.40% in 2021, indicating that the increase of ISA with >LSTmean was more pronounced in zone 3 and zone 2 during the period; (ⅲ) The driving factors of LST spatial distribution were regionally different because of the different landscape patterns, and the explanatory power for the heterogeneity of LST in zone 1 was weaker than that in zone 2 and zone 3 in the study area; (ⅳ) The interaction of different factors had a higher explanatory power on the spatial distribution of LST than a single factor in each zone because the distributions of land cover types are heterogeneous in urban area. The results of the study can be used to improve urban planning for urban ecology and UHI mitigation.

Zinc-oxide (ZnO) nanostructures including nanorods are currently considered as a pioneer research of interest world-wide due to their excellent application potentials in various applied fields especially for the improvement of energy harvesting photovoltaic solar cells (PSC). We report on the growth and morphological properties of zinc-oxide (ZnO) nanorods grown on the surface of plain zinc (non-etched and chemically etched) plates by using a simple, economical, and environment-friendly technique. We apply hot water treatment (HWT) technique to grow the ZnO nanorods and varies the process parameters, such as temperature and the process time duration. The morphological, and elemental analysis confirm the agglomeration of multiple ZnO nanorods with its proper stoichiometry. The obtained nanostructures for different temperatures with different time duration showed the variation in uniformity, density, thickness and nanonorods size. The ZnO nanorods produced on the etched zinc surface were found thicker and uniform as compared to those grown on the non-etched zinc surface. This chemically etched Zinc plates preparation can be an easy solution to grow ZnO nanorods with high density and uniformity suitable for PSC applications such as to enhance the energy conversion efficiency of the photovoltaic (PV) solar cells towards the future sustainable green earth.

Giant plasmonic surface enhancement has been observed in gold coated micron sized inverse pyramids entrapping a gold nanoparticle. The amplification of both surface enhanced Raman and photoluminescence signals was found to be dependent on the diameter of trapped gold nanoparticle and around 50-fold enhancement was detected for 250nm diameter sample relatively to the 50nm one. Finite differential time domain simulations, performed to determine the near-field distribution in the structure, showed that when the nanoparticle protrudes into the hotspot zone of the void, coupling of electromagnetic field occurs and the plasmon-related near-field enhancement is concentrated into the close vicinity of the nanoparticle, mainly into the close gaps around the tangential points of the curved sphere and the flat pyramid surface. This results in a more than 15 times increase of the near-field intensity, compared to the empty void.

Managing sidelobe levels (SLLs) in metasurface-driven beam-steering antennas poses a significant challenge due to intrinsic factors leading to grating lobes. Our proposed method employs an equivalent model to optimize large periodic metasurfaces efficiently. This model predicts complete metasurface performance, accounting for mutual coupling between patches. We introduce an evolutionary optimization algorithm based on the Cross Entropy (CE) method to enhance PGM-based beam-steering antennas and suppress sidelobes. Two strategies were employed: first is to optimize the patch dimensions for a sidelobe-free pattern and the second is to maintain the PGM dimensions while optimizing feed array amplitudes. Both strategies effectively suppressed sidelobes, offering insights into the CE method's applicability and effectiveness for CPU-intensive electromagnetic optimization challenges. The proposed CE method variant retains its simplicity while improving monitoring capabilities, addressing this limitation. Smaller generations yield better improvements per evaluation

In this paper, we present an experimental procedure to enhance the dimensional accuracy of fabrication via Stereolithography (SLA) of features at the micro-scale. Using a custom benchmark part, deviations in feature dimensions (micro-pores diameters and depths) were detected and measured by confocal microscopy. Samples characterization and experimental observations allowed the identification of inaccuracy sources, mainly due to the laser beam scanning strategy and to the incomplete removal of uncured liquid resin in post-processing (i.e., IPA washing). As a technology baseline, the measured dimensional errors on pores diameters were up to -46%. A compensation method of the nominal laser spot diameter (85m) was defined and implemented resulting in relevant improvements in dimensional accuracy of 9.8% and 11.3% on full-open pores diameter and depth, respectively. Further investigation was performed on a customized test part to adjust the calibration procedure. The measurements revealed that the estimate of the laser beam spot size is 968m. Measurements on micro-pores having different sizes revealed that a constant compensation parameter (i.e., C=85, 96, 120m) is not fully effective at the micro-scale, where average errors still remain at -24%, -18.8%, and -16% for compensations equals to 85, 96 and 120m, respectively. A further experimental campaign allowed the identification of an effective nonlinear compensation law where the compensation parameter depends on the micro-feature size C= f (D). Results show a sharp improvement in dimensional accuracy on micro-pore fabrication, with errors consistently below +8.2%. The proposed compensation method can be extended for the fabrication of any micro-features without restrictions on the specific technology implementation. Concerning the inaccuracy introduced by the laser path, experimentation with a customized part allowed the optimization of the part orientation to reduce the errors and their differences along the X and Y machine axes.

Numerous structures at the nano- and microscale manifest distinctive properties with far-reaching implications across diverse fields, including electronics, electricity, medicine, and surface engi-neering. Established methods such as nanoimprint lithography, photolithography, and self-assembly play crucial roles in the fabrication of nano- and microstructures; however, they exhibit limitations in generating high-aspect-ratio structures when utilizing high-viscosity pho-tocurable resins. In response to this inherent challenge, we propose a highly cost-effective ap-proach facilitating the direct replication of high-aspect-ratio structures, specifically nanowires, through the utilization of anodized aluminum substrates. This study elucidates the streamlined fabrication process for multiscale porous surfaces achieved through the evaporation-induced in-tegration of solid nanowires printed with high-viscosity photocurable resin.

A finite-type immersion or smooth map is a nice tool to classify submanifolds of Euclidean space, which comes from eigenvalue problem of immersion. The notion of generalized 1-type is a natural generalization of those of 1-type in the usual sense and pointwise 1-type. We classify ruled surfaces with generalized 1-type Gauss map as part of a plane, a circular cylinder, a cylinder over a base curve of an infinite type, a helicoid, a right cone and a conical surface of $G$-type.

Unlike stratospheric ozone (O₃), which is beneficial for Earth due to its capacity to screen the surface from solar ultraviolet radiation, tropospheric ozone poses a number of health and environmental issues. It has multiple effects that drive anthropogenic climate change, ranging from pure radiative forcing to a reduction of carbon sequestration potential in plants. In the central Mediterranean, which itself represents a hotspot for climate studies, multi-year data on surface ozone have been analyzed at the Lamezia Terme (LMT) WMO/GAW coastal observation site, located in Calabria, Southern Italy. The site is characterized by a local wind circulation pattern that results into a clear differentiation between western-seaside winds, which are normally depleted in pollutants and GHGs, and northeastern-continental winds, which are enriched in these compounds. This study is a first detailed attempt at evaluating ozone concentrations at LMT and their correlations with meteorological parameters, which provide new insights on the source of locally observed tropospheric ozone mole fractions. This research shows that surface ozone daily and seasonal patterns at LMT are “reversed” compared to the patterns observed by comparable studies applied to other parameters and compounds, thus confirming the general complexity of anthropogenic emissions into the atmosphere and their numerous effects on atmospheric chemistry. These observations could contribute to the monitoring and verification of new regulations and policies on environmental protection, cultural heritage preservation, and the mitigation of human health hazards in Calabria.

The position accuracy of polishing tool affects the surface quality of the polished aspheric surface. The contact deformation among the polishing tool, abrasives and aspheric part can cause a displacement, in turn will cause a position error of polishing tool, this will lead to a significant change of the polishing force. In order to resolve this error, this paper proposed a method of normal displacement compensation for NC polishing system by controlling the polishing force. Firstly, the coupling principle between polishing force and position of polishing tool are expounded, the relationship between normal displacement and deformation is analyzed, based on Hertz theory, a model of normal displacement is established. Then, on the basis of decoupled polishing system developed, a normal displacement compensation method was proposed. Finally, a group of comparative experiments was carried out to verify the effectiveness of the proposed method. Compared with no displacement compensation, when the part was polished with normal displacement compensation method, the value of roughness decreases from 0.4µm to 0.21µm, and the unevenness coefficients of surface roughness decreases from 112.5% to 19%. The experimental results show that the polishing quality is improved greatly and the aspheric surfaces can be polished more uniformly with method proposed in this paper.

We perform first-principles Molecular Dynamics calculations to test the total attraction forces on a physisorbed molecule at a given temperature and ambient pressure and apply it to the hydrogen storage on the 2D material MoP2. We considered the pristine material and one with 12.5% of Mo vacancies. By optimization, we calculated a gravimetric capacity for pristine MoP2 of 5.72%, with an adsorption energy of ‒ 0.13 eV/molecule. We found 6.02% and ‒ 0.14 eV/molecule for the second case. Next, we apply our approach to know if the molecular hydrogen physisorption obtained by simple energy optimization exists for a given temperature and ambient pressure. We used this approach to determine the number of molecules adsorbed on the surface at a given temperature. Thus, we conducted a first-principles molecular dynamics (FPMD) calculation at temperature T1, using optimization as the initial system configuration. Subsequently, we performed a second FPMD calculation at a temperature T2 (with T2 ‹‹ T1), using the stable configuration of the first FPMD calculation as the initial configuration. We identified as adsorbed molecules at temperature T1, only those forced back toward the surface at temperature T2 due to kinetic energy loss at the lower temperature T2. The defective surface gave the best gravimetric capacity, ranging from 5.27% at 300 K to 6.02% at 77 K. The latter met the requirement from the US-DOE, indicating the potential practical application of our research in hydrogen storage.

The corrosion behavior of the TiTaNbZrAg alloys with different amounts of Tantalum (0 %, 10 % and 20%) and with distinct surface topography (smooth and rough) was investigated in phosphate buffer solution (PBS) for long-time immersion (1000 hours). The corrosion resistance was studied by Open circuit potential (OCP), potentiodynamic polarization (PP) and electrochemical impedance spectroscopy (EIS). From the potentiodynamic investigations, it was observed that all types of samples show good corrosion resistance (i.e. Rcorr < 10µm y-1) and may be used successfully for medical applications. However, the samples with smooth surface and with a certain amount of Ta (10 % and 20%) exhibit the best corrosion performance (Rcorr < 1µm y-1). As regard the samples with rough surface, the results evidenced that they show lower corrosion resistance (1< Rcorr < 3 µm y-1), suggesting that the Ta presence not necessary brings about a very good corrosion protection. Actually, the synergetic effect of both the presence of Ta and surface roughness plays an important role in corrosion behavior. Based on literature reports, we assume that the good corrosion resistance results from the good stability of the film, formed mainly from Ta2O5 and TiO2, formed on the alloy surface during immersion in PBS.

This study describes the development of an optical-based surface plasmon resonance (SPR) aptasensor for the detection of cocaine. The aptasensor was prepared by first attaching gold nanoparticles to a clean SPR chip surface, followed by the addition of an aptamer to create a modified surface. This surface was characterized using Contact Angle and Atomic Force Microscopy, revealing surface roughness values of 0.28 nm and 28.12 nm for the blank and modified surfaces, respectively. The detection of cocaine was carried out in the concentration range of 1 ng/mL to 1000 ng/mL, with a detection time of approximately 8 minutes and a cocaine limit of detection (LOD) of 0.43 ng/mL. Repeatability studies were conducted, and the stability of the signal response was examined at a concentration of 200 ng/mL. Adsorption isotherm models, including Scatchard, Langmuir, and Freundlich, were calculated to assess the surface homogeneity of the SPR aptasensor chip, with the results indicating compatibility with the Langmuir isotherm model.

All-inorganic perovskite materials are promising in optoelectronics but their morphology is a key parameter for achieving high device efficiency. We prepared CsPbBr3 perovskite microcrystals with different shape, grown directly on planar substrate by conventional drop casting. We observed the formation of CsPbBr3 microcubes on bare indium tin oxide (ITO) coated glass. Interestingly, with the same technique CsPbBr3 microrods were obtained on (3-Aminopropyl) triethoxysilane (APTES) modified ITO-glass, which we ascribe to modification of formation kinetics. The obtained micro-crystals exhibit orthorhombic structure. Green photoluminescence (PL) emission is revealed from the CsPbBr3 microrods. Contact angle measurements, Fourier-transform infrared and PL spectroscopies confirmed that APTES linked successfully to the ITO-glass substrate. We propose a qualitative mechanism to explain the anisotropic growth. The microrods exhibited improved PL and slower PL lifetime compared to the microcubes, likely due to diminished occurrence of defects. This work demonstrates the importance of the substrate surface to control the growth of perovskite single crystals and to boost the radiative recombination in view of high performance optoelectronic devices.

A series of nanospherical shaped silicates containing heteroatoms (Al, Zr or Ti) were successfully synthesized using TEOS or silica colloids as silicon source. These metallosilicate nanospheres were used as silicon nutrients to obtain silicalite zeolites having micro-mesoporosity with improved textural properties. The results demonstrated that TEOS acted as a suitable silicon source to produce amorphous silicates and a spherical-type hierarchical zeolite architecture with Zr and Ti heteroatoms included in their framework, with preferable particle size and crystallinity. The surface functionality of the mesostructured nanospheres and zeolite silicates provide active centers for the esterification of glycerol with acetic acid (EG) reaction. Besides, the dispersion of Cu or Fe entities on the surface of the nanospherical silicates and zeolites provided good catalytic performances in the esterification of glycerol to valuable acetins.

Strip steel surface defect recognition research has important research significance in industrial production. Aiming at the problems of defect feature extraction difficulty, slow detection speed and insufficient dataset, YOLOv5 is improved on the basis of YOLOv5, and YOLO-LFPD (Lightweight fine particle detection) model is proposed. By introducing the RepVGG (Re-param VGG) module, the robustness of the model to the surface defect features of strip steel is enhanced, and the expressive ability of the model is improved. FasterNet is used to replace the backbone network, which ensures the accuracy and accelerates the inference speed, making the model more suitable for real-time monitoring. The use of pruning, GA genetic algorithm with OTA loss function method further reduces the model size while better learning the strip steel defect feature information, thus improving the generalisation ability and accuracy of the model. The experimental results show that the introduction of the RepVGG module and the use of FasterNet can well improve the model performance, with a reduction of 48% in the number of parameters, a reduction of 13% in the number of GFLOPs, an inference time of 77% of the original, and an optimal accuracy compared with the network models in recent years. The experimental results on the NEU-DET dataset show that the accuracy of YOLO-LFPD is improved by 3% to 81.2%, which is better than other models, and provides new ideas and references for the lightweight strip steel surface defect detection scenarios and application deployment.

Climate change and over-exploitation are imposing unprecedented threats to the groundwater resource. Globally, groundwater reserves have depleted to the extent that well yield have decreased, pumping cost have risen, and land have irreversibly subsided. In Malawi, groundwater quantity is a national problem, specifically in Mzimba district due to severe droughts. In this study, the spatial and temporal trends of groundwater depletion was assessed using Gravity Recovery and Climate Experiment (GRACE) data and Land Surface Models (LSM) from Global Land Data Assimilation System (GLDAS) and Global Surface Water Explorer (GSWE). The results show that 1. Groundwater storage is depleting at an average rate of-1.0 ± 0.06 cm yr-1(0.1043 km3yr-1) in the study area with high rate of up to -1.2 cm yr-1(0.12516 km3 yr-1) in the western side and as low as –0.4 cm yr-1(0.04172 km3 yr-1) in the eastern part. 2. Groundwater storage increases from -13 cm in November up to 15 cm between May and April. 3. Drought is the primary cause of such depletion trends with correlation between active evapotranspiration and groundwater depletion, and downward surface shortwave radiation and groundwater depletion, at -0.577 and -0.678 respectively. The results from the study reveals the need for the scientific community and the general public to consider groundwater recharge strategies specifically by mitigating climate change to reduce prolonged droughts. The study suggests the need to establish a stand-alone groundwater assessment and monitoring authority for enhanced conservation efforts of the water resource in the country.

Our study utilized density functional theory (DFT) to explore a 2D MoP2 surface for hydrogen storage. Optimization determined a gravimetric capacity for pristine MoP2 of 5.72%, with an adsorption energy of ‒ 0.13 eV/molecule. For this surface with 12.5% Mo vacancies, we achieved 6.02% and ‒ 0.14 eV/molecule. We then introduced a novel criterion to test the attraction forces in hydrogen storage at a given temperature. This involved a first-principles molecular dynamics approach at various temperatures. To determine the number of molecules adsorbed on the surface at temperature T1, we conducted an FPMD calculation at T1, using the optimization as the initial system configuration. Subsequently, we performed a second FPMD calculation at a temperature T2 (with T2 ‹‹ T1), using the stable configuration of the first FPMD calculation as the initial configuration. If there were attraction forces on the molecules, they would move towards the surface. We identified as adsorbed molecules at temperature T1, only those that moved back toward the surface at temperature T2. The defective surface gave the best gravimetric capacity, ranging from 5.27% at 300 K to 6.02% at 77 K. The latter met the requirement from the US-DOE, indicating the potential practical application of our research in hydrogen storage.

Surface treatment of implants facilitates osseointegration, with nanostructured surfaces exhibiting accelerated peri-implant bone regeneration. This study compared bone-to-implant contact (BIC) in implants with hydroxyapatite (HA), sand-blasted and acid-etched (SLA), and SLA with calcium (Ca)-coated (XPEED®) surfaces. Seventy-five disk-shaped grade 4 Ti specimens divided into three groups were prepared, with 16 implants per group tested in New Zealand white rabbits. Surface characterization was performed using X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), digital microscopy, and a contact angle analyzer. Cell viability, proliferation, and adhesion were assessed using MC3T3-E1 cells. Apatite formation was evaluated using modified simulated body fluid (m-SBF) incubation. After 4 weeks of healing, the outcomes reviewed were BIC, bone area (BA), removal torque tests, and histomorphometric evaluation. Microstructure analysis revealed irregular pores across all groups, with the XPEED group exhibiting a nanostructured Ca-coated surface. Surface characterization showed a crystalline CaTiO3 layer on XPEED surfaces, with evenly distributed Ca penetrating the implants. All surfaces provided excellent environments for cell growth. The XPEED and SLA groups showed significantly higher cell density and viability with superior osseointegration than HA (p &lt; 0.05); XPEED exhibited the highest absorbance values. Thus, XPEED surface treatment improved implant performance, biocompatibility, stability, and osseointegration.

With increasing air and sea temperatures, the thermodynamic environments over the oceans become more favourable for the development of intense tropical cyclones (TCs) with rapid intensification (RI). In fact, the number of TCs undergoing RI is rising (Zhao, et al., 2018; Bhatia, et al., 2019; Song, et al., 2020; Hong & Wu, 2021; Liu, et al., 2022). RI over coastal sea areas before landfalling is particularly impactful and threatening to coastal lives and properties. There have been studies showing that offshore areas within 400 km of the coastline have experienced a significant increase in RI events with the count tripling from 1980 to 2020 (Li et al., 2023). The south China coastal region consists of highly densely populated cities especially the Pearl River Delta (PRD) region. Intense TCs maintaining its strength or RI of TCs close to the coastal region presents substantial forecasting challenges. This study investigates the effect of sea surface and subsurface temperature and salinity on the intensification of five TCs, namely Super Typhoons Hato in 2017 and Mangkhut in 2018, Typhoon Talim, Super Typhoon Saola and Severe Typhoon Koinu in 2023, which significantly affected the south China coastal region and triggered high TC warning signals in Hong Kong. The analysis utilized the Hong Kong Observatory (HKO) TC track and intensity data, along with the sea temperature and salinity profiles generated using the China Ocean ReAnalysis version 2 (CORA2) of the National Marine Data and Information Service (NMDIS) of China. While high sea surface temperature (SST) of 30°C or above, low surface sea surface salinity (SSS) of 34 psu or below, and strong salinity stratification of at least 0.8 psu per 100 m depth may offer useful hints for predicting RI, they are part of a broader set of contributing factors. This study represents the initial documentation of sub-surface salinity's impact on intense TCs over the South China Sea (SCS) in recent years and will encourage further research to refine forecasting RI of TCs before making landfall near PRD taking into account the effect of freshwater from the Pearl River.

A detailed review of the scientific literature was undertaken to examine the most recent developments in plasma processing in the field of medicine. The first part of the review includes a detailed breakdown of the different types of coatings that can be applied onto medical devices using plasma, with a specific focus on antimicrobial surfaces. The developments during 2023 in plasma deposited biocompatible, drug delivery and adhesive coatings are described and specific applications in additive manufacturing are highlighted. The use of plasma and plasma activated liquids as standalone therapeutics continues to evolve and pertinent advances in this field are described. In addition, the combination of plasma medicine with conventional pharmaceutical interventions was reviewed and key emerging trends were highlighted, including the use of plasma to enhance drug delivery directly into tissue. The potential synergies between plasma medicine and chemotherapeutics for oncology and infection treatment is a growing area and recent advancements are noted. Finally, the use of plasma to control excess antibiotics and to intentionally degrade such materials in waste streams is described.

The high reactivity of acetylene group the formation of strong chemical bonds with active sites on mineral surfaces, thereby improving the flotation performance of gold minerals. This study utilized Density Functional Theory (DFT) to analyse the quantum chemical parameters of structure, Mulliken population, and the frontier orbitals of a thioester collector containing an acetylene group, PDEC (prop-2-yn-1-yl diethylcarbamodithioate). PDEC is compared with analogous thioester collectors Z-200 and Al-DECDT, and the interaction mechanism of PDEC on the Au(1 1 1) surface is simulated, followed by empirical validation through adsorption experiments. The findings indicate that S atom of PDEC in the carbon-sulfur group exhibit shorter covalent bond lengths, and reduced carbon-sulfur double bonds and Mulliken population, resulting in enhanced electron localization. This confers greater selectivity to PDEC during its adsorption on mineral surfaces. Frontier orbital analysis shows that the electrons of acetylene group possess a notable electron-accepting capacity, significantly influencing frontier orbital energy of PDEC and playing a pivotal role in the bonding interaction with mineral surfaces. Both the S atom in carbon-sulfur group and its acetylene group establish stable adsorption structures with the A(111) surface in a single coordination mode. The adsorption energy sequence is PDEC > Al-DECDT > Z-200. Partial density of states demonstrates that S 3p orbit of carbon-sulfur group hybridize with Au 5d orbit, while the C 2p orbit of the acetylene group engage in weaker back-donation bonding with Au 5d orbit. This is corroborated by electron density difference and post-adsorption Mulliken population analyses, revealing that S atom of carbon-sulfur group in PDEC donate electrons to Au atom, forming dominant positive coordination bonds, whereas the acetylene group accepts partial electrons from Au atom, resulting in weaker back-donation bonds. The adsorption experiments align with the DFT adsorption energy results.

Surface Plasmon Resonance (SPR) technology has been known as a powerful tool for studying biomolecular interactions because it offers real-time and label-free multiparameter analysis with high sensitivity. This article summarizes the results that have been obtained from the use of SPR technology in studying the dynamics of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) mutations. This paper will begin by introducing the working principle of SPR and the kinetic parameters of the sensorgram which include the association rate constant (ka), dissociation rate constant (kd), equilibrium association constant (KA), and equilibrium dissociation constant (KD). At the end of the section, we will summarize kinetic data on the interaction of SARS-CoV-2 with different variants with various ligands which were obtained from the results of SPR signal analysis. These affinity-related kinetic data are very useful both in drug discovery for therapeutic purposes and in the detection of SARS-CoV-2.