In this study, the gravimetric characterization and analysis of the solubilized extract of the organic fraction of Urban Household Solid Waste (RSDU) from the municipality of Belém do Pará was carried out in order to obtain the composition of the collected materials and the characteristics of the liquid resulting from the solubilization of these materials . The waste used to carry out this research was collected door-to-door, in which the points and neighborhoods served were determined through the sectorization of these locations and representative statistical sampling. For the sectorization of neighborhoods, family income values ​​were considered as the main parameter. After collecting the solid waste, the material was sent to the facilities of the Federal University of Pará (FUPa), where the waste was classified into paper, cardboard, tetrapak, rigid plastic, soft plastic, metals, glass, organic matter, waste toilets, fabrics and others. The organic fraction of solid waste was separated and sent to the drying, crushing and packaging processes. Subsequently, the solubilized extract of the organic fraction of solid waste was obtained, following the methodology recommended by NBR standard nº 10.006/2004, of the Brazilian Association of Technical Standards and the values ​​obtained were compared with Ordinance GM/MS nº 888/2021 and CONAMA Resolution nº 357/2005, in addition to results obtained by other authors. After carrying out the gravimetric characterization, it was possible to obtain the average proportions of 5.09% paper, 3.20% cardboard, 0.94% tetrapak, 3.58% rigid plastic, 9.97% soft plastic, 2.00% metals, 55.57% organic matter, 1.86% glass, 14.26% sanitary waste, 3.23% fabrics and 3.00% other waste. High values ​​of organic residues were found in the gravimetric composition, which can be explained by the collection method used and the high humidity of the organic solid residues. In the analyzes of the solubilized extract, values ​​of Hp (3.69 to 4.92), Turbidity (791 to 1,733 uT), Apparent Color (8,500 to 12,500 uC), True Color (6,000 to 14,000 uC), Total Dissolved Solids (5,330 to 8,040 mg/L), Total Nitrogen (201.80 to 359.90 mg/L), Ammoniacal Nitrogen (161 to 289 mg/L), Nitrate (10 to 40 mg/L), Total Phosphorus (52.30 to 166.80 mg/L) and Chemical Oxygen Demand (28,701 mg/L to 38,608 mg/L), in addition to other measured parameters, in which such information makes it possible to check the similarities of the waste solubilization conditions to that of leachates from landfills, in addition to not being in compliance with environmental and health legislation, demonstrating risks to the local environment and public health.

Due to the special characteristics of the shooting distance and angle of remote sensing satellites, the pixel area ratio of ship targets is small and the feature expression is insufficient, which leads to unsatisfactory ship detection performance and even situations such as missed detection and false detection. In this study, we propose an improved-YOLOv5 algorithm. The improvement strategies mainly include: (1) Add the Convolutional Block Attention Module (CBAM) into the Backbone to enhance the extraction of target-adaptive optimal features; (2) Introduce cross-layer connection channel and lightweight GSConv structure into the Neck to achieve higher-level multi-scale feature fusion and reduce the number of model parameters; (3) The Wise-IoU loss function is used to cal-culate the localization loss in the Output, and assign reasonable gradient gains to cope with dif-ferences in image quality. In addition, during the preprocessing stage of experimental data, a me-dian and bilateral filter method is used for noise reduction to reduce interference from ripples and waves and highlight the information of ship features. The experimental results show that Im-proved-YOLOv5 has a significant improvement in recognition accuracy compared to various mainstream target detection algorithms; Compared to the original YOLOv5s, the mean Average Precision (mAP) has improved by 3.2% and the Frames Per Second (FPN) has accelerated by 8.7%.

This study examined carbon footprint as an indicator of soil health at spatiotemporal scales with different land use types and varying soil depths in Morogoro, representing the eastern agroecological zone of Tanzania. Soils are highly weathered and acidic. The specific objectives were twofold: (1) To quantify soil organic carbon (SOC) at varying soil depths (0–15 cm, 15–30 cm) in contrasting land use types, including tractor cultivated, hand-hoe cultivated, ranch land, and reserved/bare land type; (2) To predict carbon management indices (CMI) of the studied land use types through regresses SOC, carbon pool index (CPI), and lability index (LI) at varying soil depths. Composite soil samples were based on transects of three main plots each (replicates) of 20 m by 50 m. Results showed that land use types and soil depths significantly (P <0.001) affected SOC (3.4%) and CMI (126.3). Hand hoe cultivated land at 0–15 cm recorded CMI of 259.8. Regression analysis showed an increase in CMI ranging from 97% to 99%, with standard error ranging from 2.177 to 46.096. Similar trends, but with disparity magnitudes in regressed parameters provide useful insight into transformations of organic carbon in contrasting land use types.

The removal of metal ions by biosorption on inexpensive materials is still a challenge for environmental engineering research. In this study, marine green algae biomass (Ulva lactuca sp.) and the biochars obtained from this biomass, at 320 C (BC-320) and 550 C (BC-550), were used as biosorbents for the removal of Cu(II) ions from aqueous solution. In addition to comparing the biosorption capacities, the determination of the thermodynamic parameters allows the choice of the most suitable material for the biosorption processes. The experimental results, obtained for Cu(II) ions biosorption on each biosorbent (algae biomass (AB), BC-320 and BC-550), at three different temperatures (10, 30 and 50 C) were analyzed using Langmuir and Freundlich isotherm models, while pseudo-first order, pseudo-second order and intra-particle diffusions models were used to model the kinetic data. The biosorption of Cu(II) ions is best described by the Langmuir model and the pseudo-second kinetic model, regardless of the type of biosorbent. The maximum biosorption capacity (qmax, mg/g) depends on the temperature, but also on the type of biosorbent, and follow the order: BC-320 &lt; AB &lt; BC-550. Using the experimental isotherms, the thermodynamic parameters (G0, H0 and S0) for the biosorption of Cu(II) ions on each biosorbent were calculated. The analysis of the obtained values constitutes the main arguments in choosing BC-550 as the most effective biosorbent for the removal of Cu(II) ions from aqueous media.

Soil erosion due to soil erosion is an important ecological impact factor. In order to further explore the impact and contribution of soil and water conservation measures on sand production and transport in the watershed, and also to provide a reference for soil erosion control, soil and water conservation and ecological environmental protection in the Yellow River Basin. In this paper, based on the measured data from the Henan Soil and Water Conservation Observatory in the Yellow River Basin, we select appropriate equations for quantifying soil erosion factor to calculate the rainfall erosion, topography, soil, vegetation and soil conservation measures in the basin, and then analyse the changes in soil erosion factor and the actual benefits of soil conservation measures in the basin. The results show that there is an increasing trend in the rainfall erosion force factor R in the Yellow River Basin; Soil erosion can be K value made the vertical loess > yellow clunamon soil, the overall change shows a decreasing trend, indicating that erosion control has produced results and that attention should be paid to erosion control in the lithosol region in the future; Since the slope lengths of the runoff plots are laid out consistently with the same LS values for both topographic factors, soil erosion is severely increased when the slope exceeds 20°. The C value of natural vegetation is small, while the C value of bare land is large. The authorities should continue to promote the return of farmland to forests and grasses and pay attention to the self-regulation and restoration of ecosystems; There is an overall decreasing trend in the P value of the soil and water conservation measures factor, the soil and water conservation measures have been effective in providing good protection.

Regulatory monitoring networks are often too sparse to support community-scale PM2.5 exposure assessment while emerging low-cost sensors have the potential to fill in the gaps. Recent advances in air quality monitoring have produced portable, easy-to use, low-cost, sensor-based monitors, which has given a new dimension to the air pollutant monitoring and has democratized the air quality monitoring process by making monitors and results directly available at community level. This study used PurpleAir(c) sensors for PM2.5 assessment in California, USA. Evaluation of PM2.5 from sensors included Quality Assurance &amp; Quality Control (QAQC) procedures, assessment with respect to reference monitored PM2.5 concentrations, and formulation of a decision support system integrating these observations using geostatistical techniques. The hourly and daily average observed PM2.5 concentrations from PurpleAir monitors followed the trends of observed PM2.5 at regulatory monitors. PurpleAir monitored PM2.5 also captured the peak PM2.5 concentrations due to incidents like forest fire. In comparison with reference monitored PM2.5 levels, it was found that PurpleAir PM2.5 concentrations were mostly higher. The most important reason for PurpleAir higher PM2.5 concentrations was the inclusion of moisture or water vapor as aerosol in contrast to measurements of PM2.5 excluding water content in FEM/FRM and non-FEM/FRM monitors. On long term assessment (2016-2020), R2 was between 0.54 and 0.86 at selected collocated PurpleAir and regulatory monitors for hourly PM2.5 concentrations. Past research studies have been conducted for mostly shorter time periods (&lt;3-4 months) that resulted in higher R2 values between 0.80 to 0.98. This study aims to provide reasonable estimations of PM2.5 concentrations with high spatiotemporal resolutions based on statistical models using PurpleAir measurements. The methods of Kriging and IDW, geostatistical interpolation techniques, showed similar spatio-temporal patterns. Overall, this study revealed that low-cost, sensor based PurpleAir sensors could be effective and reliable tools for episodic and long-term ambient air quality monitoring.

Forests, integral to human civilization, hold immense value and play a vital role in maintaining ecological harmony. Despite India's goal of extensive forest coverage, significant progress is still needed. Uncontrolled forest fires pose a severe threat, particularly in Uttarakhand's Pauri Garhwal district. To address this challenge, a comprehensive study examined surface and subsurface hydrological factors influencing the forest fire occurrences, such as elevation, aspect, slope, vegetation, proximity to human settlements, proximity to waterbodies, Active faults and lineament density. A total of 15 such factors were integrated with advanced techniques of remote sensing and GIS and coupled with historical fire data to create a precise forest fire risk map using the support vector machine algorithm. Forest fire risk map was classified into 5 distinct risk zones, Very High Risk (47.38 Km2), High Risk (275.98 km2, Moderate Risk (985.49 km2), Low Risk (1741.17 km2) and Very Low Risk (2374.11 km2) aiding in proactive fire management. By embracing this innovative tool, decision-makers can protect forests, preserve biodiversity, and ensure a sustainable future for generations to come.

This paper bases on panel data from 30 provinces and municipalities in China spanning the period of 2010 to 2021 to examine the evolving mechanisms and influencing factors of agricultural product circulation efficiency in the provinces along the Belt and Road Initiative (BRI) within the context of green total factor productivity (TFP). The study research employs various methodologies including the SBM-DDF model, GML index, system GMM, and global Moran's I index. The findings are as follows: Initially, the provinces along the BRI exhibit an overall negative growth trend in the green TFP of agricultural product circulation, with a noticeable decline observed particularly after the initiation of the BRI in 2014. Secondly, foreign investment levels significantly contribute to the positive enhancement of green TFP in agricultural product circulation among the provinces along the BRI. Eventually, environmental regulations, government support, and the level of international trade in agricultural products exert significant negative impacts. Thirdly, the results of spatial effect tests reveal substantial spatial spillover effects in the green TFP of agricultural product circulation among the provinces along the BRI, as demonstrated through examinations utilizing three distinct spatial matrices.

Soil texture is a key property influencing most soil physical, chemical, and biological processes and its catchment-scale spatial variation may yields insights for soil management. Texture data are generally available only at a few locations, since sampling and laboratory analyses are time consuming. Therefore, it is essential to predict soil size particles texture variability using appropriate methods. Moreover, soil texture distribution across a catchment is influenced by erosion and sedimentation processes controlled by hillslope morphology, which can be quantified through some topographic attributes. The study was aimed to evaluate the ability of a multivariate approach based on non-stationary geostatistics to merge remotely sensed high-resolution LiDAR-derived topographic attributes with Vis-NIR diffuse reflectance spectroscopy and laboratory analysis to produce high-resolution maps of soil sand content and estimation uncertainty in a forested catchment in southern Italy. Moreover, the proposed approach was compared with the commonly used univariate approach of ordinary kriging. Soil samples were collected at 135 locations within a 139 ha-forest catchment with granitic parent material and subordinately alluvial deposits, where soils classified as Typic Xerumbrepts and Ultic Haploxeralf crop out. A number of linear trend models coupled with different auxiliary variables were compared and the best one resulted the model using clay content as auxiliary variable. The improvement of estimation from using only LiDAR data (elevation) compared to the univariate (no trend) model was rather marginal.

Background. Green spaces contribute to a significant life quality and maintain the sustainability of cities. In Benin, despite the political greening willingness, municipalities are experiencing technical issues in finding suitable spaces to achieve this goal. This study should serve many other towns. It aims at identifying suitable areas for green spaces to integrate landscaping into urban planning in Abomey-Calavi district. Methods. The multi-criteria analysis combining GIS and the hierarchical classification approach were performed. Six factors (land use, altitude, slope, distance from main roads, proximity to urban centres and distance from flood zones, water bodies) were combined using the ArcGIS "Spatial Analysis" extension to generate a map of green space suitability. Results. large areas of land, of which 23.27% are very suitable and 26.06% are suitable for landscaping in this municipality. The ranking of the factors revealed altitude, proximity to road networks, large conurbations and distance from wetlands accounting for 18%, compared with 14% for the other factors regarding the study environment. However, the use of these results must take into account the existing inhabited areas for a good site selection. Conclusion. These outputs guidance to decision-makers in choosing suitable sites for green spaces there and integrating them into sustainable development.

Industrial effluents contain contaminants that pose threats to the environment and human health. Bioremediation is an environmentally friendly, sustainable, and cost-effective approach to degrade or transform pollutants using microbial enzymes. Laccase is a versatile enzyme that oxidizes a wide range of substrates, such as dyes, phenolic compounds, pesticides, and polycyclic aromatic hydrocarbons (PAHs), with the consumption of molecular oxygen. Laccase can also remove heavy metals by forming complexes with organic ligands or reducing them to fewer toxic forms. However, the application of laccase in bioremediation is limited by its low production, stability, and specificity. Recombinant technology has been employed to enhance the expression, activity, and stability of laccase in various bacterial hosts. Immobilization techniques have been developed to improve the reusability and stability of laccase in different environmental conditions. This review summarizes the recent developments in the production optimization of recombinant laccase enzymes and their role in the bioremediation of industrial effluents. It also discusses the challenges of laccase-based biocatalytic systems for environmental cleanup.

Snow cover plays a critical role in the global energy and water cycles. Snow cover on the Tibetan Plateau (TP) provides vital water sources in western China and Himalayan regions in addition to its weather and climate significance. The massive high mountain topography of the TP is main conditions for the presence and persistence of snow cover on the plateau at the mid-low latitudes of the Northern Hemisphere (NH). However, how mountain topography controls snow cover distribution on the TP is largely remain unclear and the relationship is not well quantified. Here, the spatial distribution of snow cover and topographic controls on snow cover on the TP are examined based on snow cover frequency (SCF) derived from MODIS snow cover product (MOD10A2 v5) and digital elevation model (DEM). The results show that snow cover on the TP is spatially unevenly distributed and is characterized by rich snow and high SCF on the interior and surrounding high mountain ranges, and less snow and low SCF in inland basins and river valleys. Snow cover on the TP presents elevation dependence with the higher the altitude, the higher the SCF, the longer the snow cover duration and the more stable the intra-annual variation. Annual mean SCF below 3000 m above sea level (masl) is less than 4% and it reaches 77% above 6000 masl. The intra-annual snow cover variation below 4000 masl features a unimodal distribution, while above 4000 masl it presents a bimodal distribution. The mean minimum SCF below 6000 masl occurs in summer, while above 6000 masl it occurs in winter. Because of differences in solar radiation and water vapor sources, mean SCF generally increases with mountain slopes and it is the highest on the north-facing aspect, whereas the lowest is observed on the south-facing aspect.

With the rapid development of urbanization, the chemical evolution of groundwater is significantly affected by human activities. However, the driving mechanisms of groundwater chemical evolution at different stages of urbanization remain unclear, severely impacting the implementation of groundwater protection. This study investigated the driving mechanisms of groundwater chemical evolution based on the long-term series (from 1985 to 2015) of hydrochemical data from 19 groundwater monitoring sites in rapidly urbanizing areas (Shijiazhuang, Hebei Province, China). The results show that the concentrations of various chemical components in groundwater gradually increase with the acceleration of urbanization process, especially NO3-, which has increased from 13.7 mg/L in the primary stage of urbanization (PSU) to 65.1mg/L in the advanced stage of urbanization (ASU), exceeding the WHO drinking water standard (50mg/L), indicating that the groundwater chemistry has been significantly affected by human activities. It is interesting to find that the main hydrochemical types have changed from HCO3•SO4-Ca•Mg type water in the PSU to SO4•HCO3-Ca•Mg type water in the ASU. It is worth noting that there were obvious differences in driving factors of groundwater chemical evolution at different urbanization stages. In the PSU, the driving factors of groundwater chemical evolution were carbonate and rock salt dissolution, cation exchange, and industrial activities. However, in the intermediate stage and advanced stage, the driving factors of groundwater chemical evolution were changed to carbonate and gypsum dissolution, groundwater over-exploitation, agricultural fertilization, and domestic sewage. Based on the above conclusions, it is suggested that future groundwater management should control the amount of agricultural fertilizers, apply scientific fertilization, and prohibit the discharge of various types of non-compliant sewage, while strengthening the supervision of groundwater extraction to reduce the impact of urbanization development on the groundwater chemical evolution process.

Perfluorinated compounds (PFCs) are used in the manufacturing process of the semiconductor and display industries, and the need for emission reduction is growing as a greenhouse gas with a very large global warming potential. The decomposition characteristics of etch type and water film (WF) type plasma-wet scrubbers were investigated. The PFCs used in the study were CF4, SF6, NF3, CHF3, C2F6, C3F8, and C4F8, and the destruction removal efficiency (DRE) and by-product gas generation rate according to the changes in the parameters (total flow rate and power) of the plasma-wet scrubber were confirmed. When the total flow rate was 100 L/min and the measured maximum power (11 kW), the reduction efficiency of CF4 in the etch type was 95.60 % and the DRE of other PFCs was 99.99 %. And, in the WF type, the DRE of CF4 was 90.06 %, that of SF6 was 96.44 %, and that of other PFCs was 99.99 %. When the total flow rate was 300 L/min and 11 kW, the DRE of SF6 in the etch type was 99 %, and the DRE of NF3, CHF3, C2F6, C3F8, and C4F8 were 99.80 %, 95.34 %, 85.38 %, 88.49 %, and 98.22 %, respectively. And, in the WF type, the DRE of SF6 was 94.39 %, and the DRE of NF3, CHF3, C2F6, C3F8, and C4F8 were 99.80 %, 95.34 %, 85.38 %, 88.49 %, and 98.22 %, respectively. The by-product gas generation rate was significantly lower in the WF type.

The increasing environmental and human health concerns associated with medical waste have led to the development of environmental biotechnology as a means of mitigating its negative effects. This review paper discusses the various types of medical waste generated in healthcare facilities, as well as the potential environmental and health impacts of improper handling and disposal. It also provides an overview of the different environmental biotechnologies that have been developed to treat medical waste, including bioreactor systems, microbial treatment, and composting. The benefits and drawbacks of these technologies are also discussed. Bioremediation is a promising environmental biotechnology that can be used to treat medical waste contaminated with hazardous chemicals. Case studies from around the world demonstrate the successful application of environmental biotechnologies to medical waste management. These case studies highlight the challenges encountered, the methods used, and the results obtained. The findings of this review paper highlight the need for a comprehensive strategy for managing medical waste that includes environmental biotechnologies. Further research and development are needed to improve the effectiveness, efficiency, and sustainability of medical waste management.

The research is focusing on analyzing the concentrations of particulate matter (PM) next to a highly congested road section, with 39,900 as a maximum number of vehicles per 24 h, in the vicinity of Timisoara, Romania. Concentrations have been measured in multiple episodes using two different measurement methods, gravimetric and dynamic light scattering, showing a disperse range of PM concentrations. Presence of metal particles in the samples have been analyzed using an electron microscope. Additionally, impact on human health is described by evaluating results for inhalable, thoracic, and alveolar sized particles.

The rock strata movement deformation generated by the mining process of the mine will inevitably lead to surface subsidence and a series of environmental hazards, so it is particularly important to monitor the rock strata movement deformation and surface subsidence in the goaf area. With the development of surface subsidence monitoring technology, InSAR technology has been widely used in the research of surface subsidence in mining areas with the advantages of high precision and wide monitoring. In this paper, by obtaining the image data of 59 Sentinel-1A scenes in the mining area, the obtained PS points were analyzed and processed by ArcGIS difference analysis by PS-InSAR technology, and the surface deformation cloud map and settlement curve of the mining area in various periods were obtained, and the rock strata movement deformation and surface subsidence law of the goaf before treatment and after different treatment methods were studied by influencing factors such as stope layout and mining depth. The results show that the rock strata movement deformation and surface subsidence degree of the goaf under different treatment methods are different due to different influencing factors, and their positions also change dynamically with time. Applying InSAR technology to study rock strata movement deformation and surface subsidence can provide an important basis for mine safety mining, goaf treatment, rock strata movement deformation and surface subsidence monitoring.

Concentrator photovoltaic (CPV) technology offers an alternative to conventional photovoltaic systems, focusing on the concentration of solar radiation through the optics of the system onto smaller and more efficient solar cells. However, the surface on which the solar beam is incident must remain oriented towards the position of the sun, which requires the use of large and heavy external elements known as solar trackers. In addition to their size, these elements must be as accurate as possible to avoid misalignment. To avoid the need of these solar trackers, the concept of tracking-integrated concentrating systems has been developed. This technology has been researched to make CPV systems accessible in places where conventional systems are not viable, such as building roofs or agrivoltaic fields. This review presents a detailed classification of the existing designs in the literature and providing an overview of this type of system. By eliminating the need for external solar trackers, tracking-integrated CPV systems offer a promising solution to increase the adoption of this technology. Therefore, it is expected that these systems will be a viable and effective option for solar power generation.

The leachate discharges generated in sanitary landfills contain many pollutants that are harmful to the environment; treatments are scarce and should be carried out better. The use of coagulation-flocculation processes has been one of the most widely used, but that; Due to the complexity of the characterization of the leachate, the dosing strategy of coagulants and biopolymers needs to be clarified. Therefore, the present study is carried out to determine the doses of coagulants and biopolymers suitable for coagulation-flocculation processes in the treatment of leachates by using computational models of machine learning techniques such as Artificial Neural Networks (ANN); these allow to decrease the operations of the tests of jars in the laboratory; optimizing resources. Through laboratory experimentation, there are real results of the effectiveness of applying biopolymers in leachate treatments at different concentration levels. The laboratory results were taken as input variables for the algorithms used; after the validation and calibration process, we proceeded to estimate predicted data with the computational model, obtaining predictions of optimal doses for treatment with high statistical adjustment indicators. It is verified that the applied coagulation-flocculation treatments reduce the turbidity values in the leachate and contaminants associated with suspended solids. In this way, the jar tests are optimized so that the operational costs decrease without affecting the results of adequate dosing.

The Baltic Sea coast is one of the geographical areas of Europe most threatened by the current climate change. This issue concerns erosional processes, groundwater flows affecting sea-shore settings. Long term hydrological investigations within the western sector of the Łeba Barrier, northern Poland, based on a network of monitoring stations, coupled with the meteorology records of the past 12 years, revealed significant fluctuations in ground water fluxes from the Baltic Sea on the adjoining mainland. Groundwater resources are negatively affected by sea-level drops in the coastal areas along the southern Baltic coast. The low sea levels strengthen the effects of low precipitation and high temperatures, causing altogether the occurrence of hydrogeological drought in the coastal sandbar areas. Drought periods are characterized by lowering of water-tables in the Slowinski National Park. The obtained results have direct relevance to a long-term assessment of water resources, environmental protection of the climatically most susceptible ecosystems, as well as the tourism management of this popular visitors’ destination.

Copper smelting has been the source of soil contamination in trace metals in Penga Penga (Lubumbashi). Residents are exposed to trace metal ingestion and planting trees is challenging in such soil conditions. Nevertheless, planting trees in former household dumps or using various types of amendments allowed the provisioning of fruits in few residences. In the perspective of scaling up the process, a survey has been conducted with the aim of assessing the effectiveness of the planting processes on the trace metal content in fruits and leaves of Mangifera indica L. and Syzygium guineense (Willd) DC. Samples were collected in residential households from Penga Penga and Kalebuka (a non-polluted suburb). The bioconcentration factor (BCF) and the safe weekly consumption (SWC) were calculated for each species. Results showed higher values of total and soluble concentrations of Cu, Pb, and Zn in the rhizosphere of the two species at Penga Penga. Metal concentrations were higher in fruits and leaves from Penga Penga with 47% of samples above FAO and WHO thresholds (vs 18.5% in Kalebuka). The BCF values were below 1 demonstrating the effectiveness of the process to reduce metal translocation to leaves and fruits. Recommendations from the SWC limited by Pb for consumption to 9 kg for mango flesh and by Cd 6.6 kg for S. guineense fruits at Penga Penga (Vs 78 and 68 kg at Kalebuka). Finally, results from this study provide interesting lessons from the scaling up and the technical itinerary of planting tree un Penga Penga.

The large areas being targeted for tropical forest restoration as part of the UN Decade on Ecosystem Restoration will have major consequences for the flow of water through landscapes. Whilst the prevailing mantra that ‘more forest implies less streamflow’ remains true in terms of annual water yields, we demonstrate that opportunities for increased tree cover to improve seasonal flow regimes of streams, particularly baseflows, are important. We discuss several potential positive feedbacks of forest restoration on hydrological processes at various scales, including ‘trade-offs’ between changes in vegetation water use and infiltration after foresting degraded land; the recovery of the capacity of vegetation to capture ‘occult’ precipitation in specific coastal and montane settings; and enhanced moisture recycling and transport at various scales. Modelled changes in baseflow after foresting all degraded land climatically capable of carrying forest in the tropics suggested a positive effect in 10% of the land. For an additional 8%, the effect was predicted to be about neutral (<2 mm/y). We conclude that a more positive narrative regarding the relationship between tropical forestation and water availability is justified. It is time for greater involvement of hydrologists and atmospheric scientists in the development and assessment of forest landscape restoration efforts.

Cropland area is closely related to food production. More previous focuses were paid on impacts of extreme events on food production, but less on cropland dynamics. This study took the Farming-Pastoral Ecotone of Northern China (FPEN) as a case area, to investigate its cropland area dynamics and driving factors in view of perspectives of extreme events, environmental conditions, socioeconomic development, urban expansion, and ecological construction. We used ridge regression approach to quantify contributions of these drivers to cropland area dynamics. Results showed that cropland area increased significantly at a rate of 333.5km2/a during 1992−2020 and were spatially clustered in east of the FPEN. Impact extent and size each driving factor on cropland trend presented large spatiotemporal differences, but ecological construction (EC) had overall the greatest impact on cropland area changes, followed by urban expansion (UE). In comparison, TL10p has the smallest. UE-dominated areas increased 41.9% since 2010s, but still less than EC. Furthermore, we found that extreme events effects on cropland area trend evidently increased. Particularly, TH90p displayed the most increase (~99.4%). Cropland area changes dominated by extreme temperature events in 2010−2020 increased nearly six times than that in 1992−2010. These findings suggest that increasing impacts of extreme weather events on cropland area changes should be cautioned.

In this paper an overview of waste materials in underground coal mines is presented, whereas waste materials can be of anthropogenic or geogenic origin. Complex interactions with mine water and waste materials take place, especially during mine water level rebound. Bearing in mind that under the increasing societal pressure most, if not all underground coal mines are going to be closed rather sooner than later, it is important to understand these interactions and to predict the composition and dynamics of mine water lever rebound in underground coal mines to prevent adverse effects to the environment, especially receiving waters and drinking water resources. The second part of this article focusses on the experiences gained in the Ruhr area, a closed underground coal mining region in Western Germany, where mine water rebound has been ongoing for decades. In this regard, the modelling program DMT-Boxmodel has been developed and applied to predict the hydrodynamics and hydrogeochemical development of the water rebound. As an example, simulation results of water rebound as well as solute and PCB transport in central province of Ruhr mining area are compared to the monitoring data, and predictions over 3 decades are given. The experiences gained in the mine water management in Ruhr area can be applied in mining areas worldwide.

Commercially available multispectral and thermal imagers are commonly deployed for environmental monitoring on small uncrewed aerial systems (sUAS, <55 lbs). Our team assessed the challenges of deploying these imagers on a Group 3 classification UAS (weight: 55-1320 lbs, maximum altitude: 18,000 ft MSL, maximum speed: 250 kts) for the purpose of land-atmosphere interaction studies. A Micasense Altum multispectral imager was deployed on two very similar mid-sized (Group 3) UAS, a Mississippi State University (MSU) TigerShark XP and the Department of Energy (DOE) ArcticShark. This paper examines the effects of flight on imaging systems mounted on UASs flying at higher altitudes, faster speeds, and for longer duration, which near future technology will make more the norm. For these platforms we found that the acquisition rate may need to be higher to achieve a minimum 75% overlap, as required by certain post-processing algorithms. Additionally pre-flight calibration panel referencing was found to be problematic for converting flight images to reflectance, due to the changing illumination conditions during the extended duration flights. We developed an automated workflow to correct the image frames via data from an onboard hemispherical solar sensor mounted on the top of the airframe, and we assessed these data against known spectral ground targets and independent sources. Finally, this manuscript may be used as a reference for collecting similar datasets in the future. The datasets described within this manuscript may be used as a starting point for future research.

Land use/land cover (LULC) changes have a substantial influence on ecosystem services. The objective of this study is to estimate LULC dynamics induced ecosystem service values (ESV) changes in Western Ethiopia. Data were acquired from Landsat images of the area for four periods (1990-2020), and 221 sample households. The areas of LULC classes and the improved ESV coefficients of Costanza et al (1997) were used estimate ESV changes in 1990-2020. Forest provides diverse provisions, regulatory, supportive and cultural services. Analysis of the Landsat images showed that forest, farmland, settlement, water body and bare-land were the major LULC classes in the study area. While forest ESV had accounted 46.1% (US$ 4.95 million) of the ESV of Wayu-Tuka district in 1990, farmland ESV constituted the largest share (63.3%, US$ 5.21 million) of the ESV of the area after 30 years (2020). The ESV of forest and bare-land showed decreasing trends in three decades (1990-2020) but the farmland service value revealed an increasing trend in the same periods. Forest ecosystem exhibited the largest service value loss (US$ 3.91 million) in 1990-2020; whereas, the service value gain of farmland was only US$ 2.2 million although farmland was responsible for the conversion of the largest area size (9,766.5 ha) from other land covers in 30 years. LULC change induced net ESV loss of the district in three decades (1990-2020) was 23.4% (US$ 2.51 million). Land conversion due to expansion of farmland (by 9,766.5 ha) and settlement (by 4,061.3 ha) was the main cause for the LULC dynamics and the significant ESV loss in 1990-2020. Thus, the government and local people should cooperate so as to curb the steady degradation of forest and its ecosystem services in Wayu-Tuka district, Western Ethiopia.

Solar energy is a rapidly growing sector, and solar farms are playing an increasingly important role in meeting the world's energy needs. However, as the size and complexity of these farms increase, so do the challenges associated with managing them efficiently. This article presents a comprehensive analysis of the fundamental parameters that underpin solar energy systems. Focusing on the latest research, we examine the challenges and opportunities intrinsic to the implementation of solar energy systems, paying particular attention to the various parameters that contribute to their performance. These parameters encompass a range of factors such as thermal performance, atmospheric boundary layer, solar energy meteorology, heat islands, cloud influences, agrivoltaic systems, shading factors, and surface energy budget. The review underscores the importance of considering a diverse array of parameters when developing solar energy systems to optimize their efficiency and effectiveness. Ultimately, by unraveling these challenges and opportunities, we can work towards creating more sustainable and reliable renewable energy sources and reducing our dependence on non-renewable alternatives.

The exponential growth in the consumption of electronics, in combination with the reduction in their useful life, leads to a significant increase in the volume of electronic material discarded. Printed Circuit Boards (PCBs) are modules composed of ceramic, polymer and metallic materials of high economic value and with a great potential for damage to biotic and anthropic environments when inadequately discarded. The aims of this work was to study the main environmental impacts and the efficiency of mechanical operations in the electronic waste recycling process in optimizing the concentration of metallic copper. For this, the samples obtained were characterized according to their morphology and chemical composition, and subjected to physical and mechanical treatments: dismantling, grinding, separation by granulometry, density and magnetic property. The environment impacts were estimated by the Life Cycle Assessment of the pre-treatment processes, associated with copper extraction operations in WPCBs. According to the results obtained, it is possible to infer that the NM +1mm Concentrated product presents in its metallic composition around 78% of copper, which contributes to the efficiency of the hydrometallurgical extraction processes. It is noteworthy that the Concentrated class represents about 14% of copper (wt) taking into account the amount of 3.789 kg of PCB waste input material. The potential for reinsertion of the dust in the material recovery process is highlighted, given that the chemical composition of this particulate has a significant presence of metals. In general, it was found that due to the higher concentration (wt %) of the sample being allocated in the range of - 0.15mm + 0.05mm, the elements Fe (18.30%), Si (10.73%), Ca (9.21%) and Cu (8.89%) stand out regarding the participation of the elemental composition of this fraction and also regarding the general composition of the sample. Furthermore, the generation of dust during the fragmentation process, can be associated with occupational respiratory diseases when not managed. About the Life Cycle Assessment, in seven of the nine categories evaluated, crushing and screening activities accounted for more than 90% of the recorded impact values. In general, it is estimated that in the pre-treatment phase be generated 15.4 kg CO2 eq.

Heavy metals toxicity is a grave environmental issue in contemporary times. Phytoremediation is economic, effective and ecofriendly approach to decontaminate and remediate metal contaminated areas. Phenolic and Flavonoid content are important abiotic stress markers. The individual and combined impacts of toxiferous metals Arsenic (As), Cadmium (Cd) and (Copper) Cu were employed in recent studies to investigate their effect on Total flavonoids content (TFC) and total phenolic content (TPC) in various parts of Hydrocotyle umbellata L. to explore the role of plant in abating metal contamination. Folin- ciocalteu and AlCl 3 methods were used for investigating TPC and TFC respectively. Two-way ANOVA and CART model were employed for statistical analysis. Highest TPC was examined in decreasing order as leaf &amp; gt; stem &amp; gt; root in case of all the metals. Whereas highest TFC was found in all plant parts when subjected to As toxicity, and the lowest TFC was found in stem of the plant in respect to Cu toxicity. There was significant effect on TPC on plant part when subjected to Cu and As stress, but so significance was observed in plant part in case of Cd and combined metal stress. Treatment concentration had no significant effect on TPC when subjected to unique impact of all the three metals but had significant effect in case of combined metal stress. Similarly, in case of TFC no significant effect was recorded in case of plant part in all the stress types. But treatment amount has significant impact on Cd and combined metal stress. Metal type has significant effect on TPC and TFC. Whereas plant part has significant impact on TPC but non-significant values were observed on TFC in this case. This study epitomizes TPC and TFC in plants as effective and viable tool to pertain their role in phytoremediation against metal contamination. Therefore H. umbellata L. can be exerted for successful assemblage and decontamination of Cd, Cu and As in different plant parts.

The assessment outcomes of regional susceptibility to geological disasters can directly indicate the extent and intensity of risks within the study area, thus, providing targeted guidance for disaster management efforts. This study selects eight evaluation indicators, namely elevation, gradient, terrain relief, lithology of strata, normalized difference vegetation index, distance from the fault, distance from road, and distance from the river. The study focuses on Huize County in Yunnan Province as the research area, utilizing the certainty factor (CF) and random forest (RF) models for evaluating the susceptibility to geological disasters. The non-geological disaster points in the study area are determined using the deterministic coefficient prior model, and the deterministic coefficient values for each evaluation factor serve as the classification data for the random forest model. The optimal parameters for the random forest are selected through iterative calculations of bag error in PyCharm, while the weight of the evaluation factor is determined based on the ran-dom forest model with the optimal parameters. The results of geological disaster susceptibility zoning in Huize County are obtained by overlaying the weighted deterministic coefficients of each evaluation factor. The accuracy of the evaluation results is verified using zoning statistics and ROC curves with a test sample of 30% of the points. The results demonstrate the high accuracy of the model in evaluating the susceptibility to geological disasters in Huize County. Compared to the single deterministic coefficient model, this approach offers advantages in terms of reliability and accuracy. The evaluation results can serve as a scientific reference for related work in Huize County.

In recent years, there has been a growing interest in remote sensing image-text cross-modal retrieval due to the rapid development of space information technology and the significant increase in remote sensing image data volume. One approach that has shown promising results in cross-modal retrieval of natural images is the multimodal fusion encoding method. However, remote sensing images have unique characteristics that make the retrieval task challenging. Firstly, the semantic features of remote sensing images are fine-grained, meaning they can be divided into multiple basic units of semantic expression. Additionally, these images exhibit variations in resolution, color, and perspective. Different combinations of basic units of semantic expression can generate diverse text descriptions. These characteristics pose considerable challenges for cross-modal retrieval. To address these challenges, this paper proposes a multi-task guided fusion encoder (MTGFE) based on the multimodal fusion encoding method. The model incorporates three tasks: image-text matching (ITM), masked language modeling (MLM), and the newly introduced multi-view joint representations contrast (MVJRC) task. By jointly training the model with these tasks, we aim to enhance its capability to capture fine-grained correlations between remote sensing images and texts. Specifically, the MVJRC task is designed to improve the model’s consistency in feature expression and fine-grained correlation, particularly for remote sensing images with significant differences in resolution, color, and angle. Furthermore, to address the computational complexity associated with large-scale fusion models and improve retrieval efficiency, this paper proposes a retrieval filtering method. This method achieves higher retrieval efficiency while minimizing accuracy loss. Extensive experiments were conducted on four public datasets to evaluate the proposed method, and the results validate its effectiveness. Overall, this study focuses on remote sensing image-text cross-modal retrieval and introduces the MTGFE model, which combines multimodal fusion encoding with multiple tasks to enhance the model’s ability to capture fine-grained correlations. Additionally, a retrieval filtering method is proposed to improve retrieval efficiency. Experimental results demonstrate the effectiveness of the proposed method.

High-precision inertial sensors or accelerometers can provide us references of free-falling motions in gravitational field in space, and serve as the key payloads for gravity recovery missions. In this work, a systematic method of electrostatic inertial sensor calibrations for gravity recovery satellites is introduced, which is applied to and verified with the Taiji-1 mission. Taiji-1 is the first technology demonstration satellite of the ``Taiji Program in Space'', which, in its final extended phase in 2022, could be viewed as a gravity recovery satellite operating in the high-low satellite-to-satellite tracking mode. Based on the calibration principles, swing maneuvers with time span about 200 s and rolling maneuvers for 19 days were conducted by Taiji-1 in 2022. The inertial sensor's operating parameters including the scale factors, the center of mass offset vector and the intrinsic biased acceleration are precisely re-calibrated and are updated to the Taiji-1 science team. Data from one of the sensitive axis is re-processed with the updated operating parameters, and the performance is found to be slightly improved compared with former results. This approach could be of high reference value for the accelerometer or inertial sensor calibrations of the GFO, the Chinese GRACE-type mission, and the planned Next Generation Gravity Missions. This could also shed some light on the in-orbit calibrations of the ultra-precision inertial sensors for future GW space antennas because of the technological inheritance between these two generations of inertial sensors.

Digital Twin Cities (DTCs) play a fundamental role in city planning and management. They allow three-dimensional modeling and simulation of cities. 3D semantic segmentation is the foundation for automatically creating enriched DTCs, as well as their updates. Past studies indicate that prior level fusion approaches demonstrate more promising precisions in 3D semantic segmentation compared to point level fusion, features level fusion, and decision level fusion families. In order to improve point cloud enriched semantic segmentation outcomes, this article proposes a new approach for 3D point cloud semantic segmentation through developing and benchmarking three prior level fusion scenarios. A reference approach based on point clouds and aerial images was proposed to compare it with the different developed scenarios. In each scenario, we inject a specific prior knowledge (geometric features,classified images ,etc) and aerial images as attributes of point clouds into the neural network’s learning pipeline. The objective is to find the one that integrates the most significant prior knowledge and enhances neural network knowledge more profoundly, which we have named the "smart fusion approach". The advanced Deep Learning algorithm "RandLaNet" was adopted to implement the different proposed scenarios and the reference approach, due to its excellent performance demonstrated in the literature. The introduction of some significant features associated with the label classes facilitated the learning process and improved the semantic segmentation results that can be achievable with the same neural network alone. Overall, our contribution provides a promising solution for addressing some challenges, in particular more accurate extraction of semantically rich objects from the urban fabric. An assessment of the semantic segmentation results obtained by the different scenarios is performed based on metrics computation and visual investigations. Finally,the smart fusion approach was derived based on the obtained qualitative and quantitative results.

Volcanic emissions (ash, gas, aerosols) dispersed in the atmosphere during explosive eruptions generate hazards affecting aviation, human health, air quality and the environment. We document for the first time the contamination of airspace by very fine volcanic ash due to sequences of tran-sient ash plumes from Mount Etna. The atmospheric dispersal of sub-10 μm (PM10) ash is mod-elled using the WRF-Chem model coupled online with meteorology and aerosols and offline with Mass Eruption Rates (MER) derived from near-vent Doppler radar measurements and inferred plume altitudes. We analyse two sequences of paroxysms with widely varied volcanological conditions and contrasted meteorological synoptic patterns in October–December 2013 and on 3-5 December 2015. We analyse the PM10 ash dispersal simulation maps in terms of time-averaged columnar ash density, concentration at specified flight levels averaged over the entire sequence interval, and daily average concentration during selected paroxysm days at these flight levels. The very fine ash from such eruption sequences is shown to easily contaminate the airspace around the volcano within a radius of about 1000 km in a matter of a few days. Synoptic patterns with relatively weak tropospheric currents lead to the accumulation of PM10 ash at a re-gional scale all around Etna. In this context, closely interspersed paroxysms tend to accumulate very fine ash more diffusively in the lower troposphere and in stretched ash clouds higher up in the troposphere. Low-pressure, high-winds weather systems tend to stretch ash clouds into ~100 km-wide clouds forming large-scale vortices 800-1600 km in diameter. Daily average PM10 ash concentrations commonly exceed the aviation hazard threshold up to 1000 km downwind from the volcano and up to the upper troposphere for intense paroxysms. Vertical distributions show ash cloud thicknesses in the range 0.7–3 km, and PM10 sometimes stagnating at ground level, represent a potential health hazard.

Soil salinity is a limiting factor in crop productivity. Inoculating crops with microorganisms adapted to salt stress is an alternative to increasing plant salinity tolerance. Few studies have simultaneously propagated arbuscular mycorrhizal fungi (AMF) and dark septate fungi (DSF) using different sources of native inoculum from halophyte plants, and evaluated their effectiveness. This study selected, in alfalfa plants as trap culture, the infectivity of 38 microbial consortia native from rhizospheric soil (19) or roots (19) coming from six halophyte plants, as well as their effectiveness in mitigating salinity stress. Inoculation with soil resulted in 26%-56% colonization by AMF and 12%-32% by DSF. Root inoculation produced 10%-56% and 8%-24% of colonization, respectively. There was no difference in the number of spores of AMF produced with both inoculum types. The effective consortia were selected based on low Na but high P and K shoot concentrations which is relevant for plant nutrition but more for salt stress mitigation. The microbial consortia selection is presented in a more novel and applicable context, which would allow for the production of native microbial inoculants adapted to salinity to diminish the harmful effects of salinity stress in glycophyte plants in the context of sustainable agriculture.

Fit-for-purpose land administration (FFPLA) seeks to simplify cadastral mapping via lowering the costs and time associated with conventional surveying methods. The approach can be applied to both initial establishment and on-going maintenance of system. In Ethiopia, cadastral maintenance remains an on-going challenge, especially in rapidly urbanizing peri-urban areas, where farmers' land rights and tenure security are often jeopardized. Automatic Feature Extraction (AFE) is an emerging FFPLA approach, proposed as an alternative for mapping and updating cadastral boundaries. This study explores the role of the AFE approach for updating cadastral boundaries in the vibrant peri-urban areas of Addis Ababa. Open-source software solutions are utilized to assess the (semi-) automatic extraction of cadastral boundaries from orthophotos (segmentation), designation of 'boundary' and 'non-boundary' outlines (classification), and delimitation of cadastral boundaries (interactive delineation). Both qualitative and quantitative assessments of the achieved results (validation) are undertaken. A high-resolution orthophoto of the study area and a reference cadastral boundary shape file are used, respectively, for extracting the parcel boundaries and validating the interactive delineation results. Qualitative (visual) assessment verified the completed extraction of newly constructed cadastral boundaries in the study area, although non-boundary outlines such as footpaths and artefacts are also retrieved. For the buffer overlay analysis, the interactively delineated boundary lines and the reference cadastre were buffered within the spatial accuracy limits for urban and rural cadasters. As a result, the quantitative assessment delivered 52% correctness and 32% completeness for a buffer width of 0.4m and 0.6m, respectively, for the interactively delineated and reference boundaries. The study further demonstrated the potentially significant role AFE could assist in delivering fast, affordable, and reliable cadastral mapping. Further investigation, based on user input and expertise evaluation, could help to improve the approach and apply it to a real-world setting.

The evaluation of suitability for bioclimatic viticulture indices (BVIs) zones, as with any other crop, requires a well-founded knowledge of the spatial variability in climate data, which is also used to assess different grapevine cultivars and to delimit appropriate regions for vineyard production under the current climate and projected climate change. BVIs, on the other hand, are typically calculated using a small number of locations linked by climatic station sites or applied using a coarsely-resolution distributed dataset. Furthermore, often the methods applied to precisely delineate symmetrical regions are not appropriate to generate accurate maps. To provide an analysis using three temperature-based indices and the hydrothermal coefficient (HTC), quantifying their spatial variation, and representing the spatial patterns of each BVI throughout the Jabal Al Arab viticulture—one of the most important Syrian viticulture regions in the Eastern Mediterranean—daily temperature data from 15 meteorological stations and 57 rain gauges, considering the 1984–2014 period, and downscaled future scenarios (RCPs based on CanESM2), considering the 2016–2100 period, were utilized. The statistical method of each BVI was analyzed, and, later, they were mapped by using GIS and a hybrid interpolation (regression-kriging) approach. The regression fitting method revealed that the sum accumulation of heat and the hydro-thermal index during the growing season were highly related to elevation and distance to the seacoast variables; however, the viticulture zones varied spatially depending on which index was used and under suggested future scenarios compared to the current climate. The spatial distribution of climate in the Jabal Al Arab regions exhibits significant variability. The findings suggest that climate change projections indicate a prevalence of warmer conditions in the future. Under the RCP scenarios, the territory can be categorized into up to three bioclimatic classes for both the Heat Index (HI) and the Winter Index-Growing Degree Days (WI-GDD), in contrast to the current climate which has six classes. These results provide valuable insights into the suitability of viticulture within each climatic region and facilitate the identification of homogeneous zones. The utilization of consistent bioclimatic indices and an advanced hybrid interpolation method has enabled the delineation and comparison of bioclimatic variables of Jabal Al Arab with other regions worldwide. Such comparisons should be considered when selecting grapevine varieties and assessing the potential for grape production.

Conducting an accurate hydrological water balance at the regional and country-wide scales is paramount to assessing available water resources and adequately allocating them. One of the main components of these balances is the anthropogenic recharge of groundwater either intentionally, through managed aquifer recharge (MAR), or unintentionally, where infiltration from dams and dykes can play a significant role. In Spain, proper management of water resources is critical due to the arid to semiarid conditions prevalent in most of the territory and the relevance of water resources for maintaining a robust agricultural sector. Spanish Previous work has estimated country-wide recharge from MAR at 150-280 Mm3/year. Recently, water authorities have pointed out that, according to hydrological water balances, the total volume from "unintentional recharge" from water courses may exceed 500 Mm3/year. The present research aims to present a new inventory of transverse structures in Spain and use it to estimate country-wide unintentional recharge. The inventory, compiled by the Spanish Ministry for the Ecological Transition and the Demographic Challenge, has more than 26,000 structures and includes construction characteristics, which allow for estimating the wet perimeter and the infiltration area. Structural data from the inventory was crossed through map algebra with thematic layers, such as lithology, permeability, the digital elevation model, the average groundwater levels, etc., in a GIS environment to arrive at the objective. Different analytical formulas to compute infiltration from small dams and dykes were also employed. The resulting volume of unintentional recharge from transverse structures in Spain is about 800 Mm3/year. This quantity can help close the hydrological balance at the national and river basin levels. Furthermore, this figure provides an order of magnitude for anthropogenic recharge at a national scale, which is difficult to obtain.

In this article, a method for the moisture mapping of the soil surface of agrophytocenosis was proposed using neural network based on synchronized radar and multispectral optoelectronic data of Sentinel-1,2. To verify the developed method, data from two experimental plots were used. These plots were located two on irrigated soybean crops. The first of them was located on the right bank (1st plot) and the second one on the left bank (2nd plot) of the down part of Volga River. Two experimental soil moisture geo-datasets were done by measurements and geo-referencing points using gravimetric method (1st plot) and with proximal sensing method (2nd plot) using Soil Moisture Sensor ML3-KIT (THETAKIT, Delta). The soil moisture retrieval algorithm was based on the use of a neural network to predict reflection coefficient of an electromagnetic wave from the soil surface, followed by inversion into soil moisture using a dielectric model that takes into account the soil texture. The input parameter of the neural network was the ratio of the microwave radar vegetation index (calculated on the basis of Sentinel-1 data) to the index (calculated on the basis of data of multispectral optoelectronic channels 8 and 11 of Sentinel-2). Such way calculated index reveals showed a significantly greater dependence on soil moisture than on vegetation height that was been used in previous studies. The retrieved values of soil moisture were compared with the soil moisture measured in-situ. The proposed method with a determination coefficient of 0.44-0.65 and a standard deviation of 2.4%-4.2% for the 1st plot as well as with and of the same metrics for the 2nd allows predicting the soil moisture of both a test plots covered by soybean plants, relative to soil moisture measured in-situ. The conducted research created the scientific basis for a new technology for remote sensing the moisture content of the soil surface of agrophytocenosis as an element of the precision farming system and agroecology.

Arsenic (As) contamination of groundwater is a common problem in BDP. The alkaline pH of the groundwater provides favourable condition for geomicrobiochemical processes, where organic matter also plays an important role in mobilization of As. The total arsenic content (AsT) of the groundwater is in the range of 69-178 µgL-1 with mean value of 118.58 µgL-1. The groundwater quality of monitored drinking water wells are related to local land–use pattern and rural sanitation installation and practices (which can have a strong influence on microbial contamination). The study indicates that As heterogeneity, probably a consequence of microbial heterogeneity is a feature of the study area. The excessive total and fecal coliform (TC and FC) count of the ponds possibly suggest uncontrolled surface run offs and sewage leakage, notably from nearby pit-latrine, which increased the microbial contamination in these water sources. The tube wells located in close proximity (~ 2-3 m) of the surveyed ponds are also contaminated with high TC and FC values, due to faulty water supply system, pond water infiltration and cracked tube well platforms. Coliforms may influence geomicrobiological processes in groundwater and thereby, contribute in As release and mobilization. The TC and FC values of monitored tube wells and ponds show seasonal variation, with high TC and FC values during wet season. Attempt has been made to focus on sanitation risk of the monitored wells (based on sanitation and fecal coliform scores) which is usually less explored. The sanitary risk score reveal the need of immediate attention to all the sites, as 25.0 %, 58.3 %, 11.1 % and 5 % of tube wells of the six sites fell under very high risk (sanitary risk score ≥ 9), high risk (sanitary risk score 6-8), intermediate risk (sanitary risk score 3-5) and low risk category (sanitary risk score 0-2), respectively. Fecal coliform score classified all the sites under intermediate risk category (FC count 10-100 per 100 ml of water). The predominance of As heterogeneity particularly in areas under high risk category (showing high TC and FC contamination) is observed along with the similar sinusoidal pattern of TC, FC and AsT content. Finally, this study shed light on the factors responsible for unsafe nature of monitored tube wells and the influence of anthropogenic activities on the microenvironment of the groundwater, which could be a probable reason behind the As heterogeneity in the groundwater of the study area.

Nowadays, consumers have growing expectations for healthier and higher-quality food, and sustainable food choices are also taking on an increasingly central role. This paper assesses the environmental loads and energy resources of vegan, semi-vegetarian, and traditional restaurant soups and main dishes, focusing on preparation and cooking phases based on the life cycle assessment. The optimal menu samples were selected based on statistical methods. Mann-Whitney and Krus-kal-Wallis tests were applied to investigate restaurant products' distribution and carbon footprint. Based on the results, the preparation phases have a more significant impact. The environmental loads for the life cycle of vegan and semi-vegetarian menus are lower. Furthermore, a sustainability assessment model was developed by integrating lean and life cycle assessment approaches called "GreenCycLEAN." Research results are helpful for the sustainability of catering establishments.

The mountains in northern Xinjiang of China were studied during the snowmelt season. Multi-source fusion live data Chinese Land Data Assimilation System (CLDAS,0.05°× 0.05°,hourly data) were used as real data, and Central Meteorological Observatory guidance forecast (SCMOC,0.05°× 0.05 °,forecasting the following 10 days in 3 h intervals) was used as forecast data, both issued by the China Meteorological Administration. The dynamic linear regression and the average filter correction algorithms were selected to revise the original forecast products SCMOC.Based on conventional temperature forecast information,we designed four temperature rise prediction algorithms for essential factors affecting snowmelt.Temperature rise prediction algorithms included the daily maximum temperature algorithm, daily temperature rise range algorithm, snowmelt temperature algorithm, and daily snowmelt duration algorithm.Four temperature rise prediction algorithms values were calculated of each prediction product.Root-mean-square error algorithm and temperature prediction accuracy algorithm were used to compare and test each prediction algorithm value from the time sequence and spatial distribution.Comprehensive tests show that the forecast product revised by the average filter algorithm was superior to revised by the dynamic linear regression algorithm as well as the original forecast product.Through these algorithms, the more suitable temperature rise forecast value for each grid point in the study area can be obtained at different prediction times. The comprehensive and accurate temperature forecast value in mountainous snowmelt season can provide an accurate theoretical basis for effective prediction of the runoff in snowmelt areas and prevention of snowmelt flooding.

Against the backdrop of global climate change, the frequency of drought events is increasing, leading to significant impacts on human society and development. Therefore, it is crucial to study the propagation patterns and trends of drought characteristics over a long-time scale. The main objective of this study is to delineate the dynamics of drought characteristics by examining their propagation patterns in China from 1951 to 2020. In this study, precipitation data from meteorological stations across mainland China were used. A comprehensive dataset consisting of 700 stations over the past 70 years was collected and analyzed. To ensure data accuracy, the GPCC database was employed for data correction and gap filling. Long-term drought evolution was assessed using both the SPI-12 and SPEI-12 indices to detect drought characteristics. Two Moran indices were applied to identify propagation patterns, and the MK analysis method along with the Theil-Sen slope estimator were utilized to track historical trends of these indices. The findings of this study reveal the following key results: (i) Based on the SPI-12, the main areas of China that are prone to drought are mostly concentrated around the Hu Huanyong Line. Indicating a tendency towards drying based on the decadal change analysis. (ii) The distribution of drought-prone areas in China, as indicated by the SPEI-12, is extensive and broadly distributed, with a correlation to urbanization and population density. These drought-prone areas are gradually expanding. (iii) Between 2010 and 2011, China experienced the most severe drought event in nearly 70 years, affecting nearly 50% of the country's area with a high degree of severity. This event may be attributed to atmospheric circulation variability, exacerbated by the impact of urbanization on precipitation and drought. (iv) The frequency of drought occurrence in China gradually decreases from south to north, with the northeast and northern regions being less affected. However, areas with less frequent droughts experience longer and more severe drought durations. In conclusion, this study provides valuable insights into the characteristics and propagation patterns of drought in China, offering essential information for the development of effective strategies to mitigate the impacts of drought events.

The implementation of grey and green infrastructure is an effective mean to address urban flooding and nonpoint source pollution, but due to the complexity of the process and the diver-sity of benefits, there is a lack of measurement for their comprehensive benefits. Adopting a typ-ical university in Beijing as an example, this paper simulated the multidimensional benefits of the water quantity, water quality, and ecology of grey and green facility renovation by coupling the storm water management model (SWMM) and InfoWorks Integrated Catchment Manage-ment (ICM). Monetization methods and economical means were employed to characterize the comprehensive benefits. The results showed that grey and green infrastructure retrofitting re-duces the number of severe overflow nodes in the study area by 54.35%, the total overflow vol-ume by 22.17%, and the nonpoint source pollution level by approximately 80% under the heavy rain scenario and 60% under the rainstorm scenario. The annual benefits of grey and green infra-structure renovation reached ¥765,600/year, of this amount, ¥83,100/year is from hydrological regulation, ¥454,100/year is from nonpoint source pollution reduction, and ¥228,300/year is from ecological improvement. The benefits of green facilities were higher than those of grey facilities, and the combined benefits were negatively correlated with the rainfall level, with a total bene-fit–cost ratio of 1.19. The results provide methodological and data support for grey and green in-frastructure retrofitting within the context of sponge cities.

Urban morphology exhibits fractal characteristics, which can be described by multifractal scaling. Multifractal parameters under positive moment orders primarily capture information about cen-tral areas with relatively stable growth, while those under negative moment orders mainly reflect information about marginal areas with more active growth. However, effectively utilizing mul-tifractal spectrums to uncover the spatio-temporal variations of urban growth remains a challenge. To addresses this issue, this paper proposes a multifractal measurement by combining theoretical principles and empirical analysis. To capture the difference between growth stability in central areas and growth activity in marginal areas, an index based on generalized correlation dimension Dq is defined. This index takes the growth rate of Dq at extreme negative moment order as the numerator, and that at extreme positive moment order as the denominator. During the stable stage of urban growth, the index demonstrates a consistent pattern over time. While during the active stage, the index may exhibit abnormal fluctuations or even jumps. This indicates that the index can reveal spatio-temporal information about urban evolution that cannot be directly observed through multifractal spectrums alone. By integrating this index with multifractal spectrums, we can more comprehensively characterize the evolutionary characteristics of urban spatial structure.

Pollution of urban surface dust with hazardous elements (HEs) is a serious environmental issue due to its toxicity and potential hazardous effects. Surface dust samples were collected from core urban, urban, and suburban gradients in the Urumqi city of the arid NW China, and the concentrations of six HEs, such as arsenic (As), cadmium (Cd), nickel (Ni), lead (Pb), mercury (Hg), and chromium (Cr), were determined. The pollution load index (PLI) and the US EPA health risk assessment model were applied to analyze and compare the pollution levels and potential health risk of HEs in surface dusts in different urbanization gradients. The obtained results indicate that the average concentrations of Hg, Cd, and Ni in surface dust decrease in the order of core urban > urban > suburban, whereas the average concentrations of As, Cr, and Pb decrease in the order of urban > core urban > suburban. The PLI of HEs in surface dust decreased in the order of core urban > urban > suburban. The concentrations of HEs in the core urban and urban gradients are relatively higher than in the suburban gradient. Furthermore, the total non-carcinogenic and carcinogenic risk index of investigated HEs in surface dust decrease in order of urban > core urban > suburban, for both adults and children. In addition, the pollution of surface dust with HEs in all urbanization gradients is more harmful to the children's health than to the adults. Overall, the potential non-carcinogenic and carcinogenic health risks of the investigated HEs, instigated primarily by oral ingestion of surface dust, are found to be within the acceptable range. However, urbanization can effects the accumulation of HEs in surface dust, and Cr is the main non-carcinogenic risk factor, whereas Cd is the main carcinogenic risk factor among the analyzed HEs in surface dust in all urbanization gradients.

During the dry season, glaciers contribute significantly to the water supply downstream, especially in areas with seasonal rainfall. It is important to have physical-based glacier models, which are more advanced in quantifying the future dynamics of glaciers and melt distribution. Toward this purpose, an investigation of different numerical modeling tools and their approach is conducted and planned further to incorporate a glacier module into a spatially distributed model called mHM (Mesoscale Hydrological Model, mhm-ufz.org). An open-source tool called MATILDA (Modeling Water Resources in Glacierized Catchments) is used beforehand to implement the glacier entities to the application catchment Maipo Basin in Chile. Due to limited time availability and source of data, the glacier melt of the MATILDA model is integrated into the mHM model to see what the implications would be if the glacier module was implemented from scratch in mHM. The analysis of the glacier hydrology resulting from the Maipo-Glacier model was carried out by comparing the modeled glacier flows with the total observed flows. To assess the credibility of the models, the results are compared based on three goodness-fit measures, specifically r^2Coefficient of Determination), NSE (Nash-Sutcliffe Efficiency), and KGE (Kling-Gupta Efficiency). Application of the mHM model in the Maipo basin in Central Chile is performed by using prepared input datasets, showing that the approach is viable as evidenced by a Kling-Gupta Efficiency of 0.80 and Nash-Sutcliffe Efficiency of 0.70 from the starting periods of 1950 to 2020. Overestimation by the mHM model occurs during the late summer season, particularly when temperature decreases. The MATILDA model is used on glacier melt distribution, forcing data is prepared from regional datasets, and a glacier profile is constructed from ice thickness datasets. According to the model, the average KGE result for the years 2012–14 and 2015–18 was respectively 0.44 and 0.41. Glacier melt produced by Matilda is in the range of 58-68 % of the total runoff and the glacier area decreased by 22-23% during the simulation period from 2012-14 and 2016-2018. A pilot sub-basin Olivares is used in the coupling mHM model with initializing MATILDA glacier melt. The new model is underestimated during the seasonal transition in the initial days of the simulation. A considerable portion of the ablation period might be missed as a result of the initial storage quality, true glacier extent, and height distribution being understated. As a conclusion, the mHM Model was capable of predicting runoff well in a mountainous region and could also serve as a monitoring tool for watershed management. There are differences in results between the two models because of the different spatial resolutions and methodologies. MATILDA have a glacier retreat routine that gives better result for the glacier characteristics such as. A new glacier dynamics model needs to be implemented in the future to develop intermediate complexity, bridge catchment, and glacier scales after using the mHM, MATILDA, and mHM with MATIDLA model for analysis of glacier and highlighting the model's deficiencies in the initial period of simulative assessments.

Drought is one natural disaster with the greatest impact worldwide. Southern Africa (SA) is susceptible and vulnerable to drought due to its type of climate. In the last four decades, droughts have occurred more frequently, with increasing intensity and impacts on ecosystems, agriculture and health. The work consisted of a systematic literature review on the drought regime’s characteristics in the SA, under current and future climatic conditions, conducted on the Web of Science and Scopus platforms, using the PRISMA2020 methodology, with usual and appropriate inclusion and exclusion criteria to minimize/eliminate the risk of bias, which lead to 41 documents published after the year 2000. The number of publications on the drought regime in SA is still very small. The country with the most drought situations studied is South Africa and the fewer studies are Angola and Namibia. The analysis revealed that the main driver of drought in SA is the ocean-atmosphere interactions including the El Niño Southern Oscillation. The documents used drought indices, evaluating drought descriptors for some regions, but it was not possible to identify one publication that reports the complete study of the drought regime, including the spatial and temporal distribution of all drought descriptors in SA.

Water deficit is one of the factors that most influence plant growth and yield. Thus, this study aimed to evaluate the effect of silicon and salicylic acid application and water deficit on the growth and photosynthetic and osmoregulatory metabolism of Talisia esculenta Radlk seedlings and their recovery potential after the resumption of irrigation. Six treatments were performed: irrigation, irrigation suspension, irrigation suspension + silicon at 0.5 g L−1, irrigation suspension + silicon at 1.0 g L−1, irrigation suspension + salicylic acid at 50 mg L−1, and irrigation suspension + salicylic acid at 100 mg L−1. The evaluations were carried out at the beginning of the experiment (T0), at 10 and 15 (DIS) days after irrigation suspension, when the seedlings showed a photosynthetic rate close to zero, and at recovery (REC). The plants were submitted to water restriction for up to 15 days, being then re-irrigated until the recovery point, which was monitored based on the photosynthetic rate. Silicon application attenuated the harmful effects of water deficit on gas exchange, initial fluorescence, promoted proline accumulation in the leaf and root, and provided higher seedling quality. Salicylic acid application contributed to the maintenance of the relative water content of leaves during the water deficit period. Silicon and salicylic acid applications can attenuate the harmful effects of water stress, with silicon being the most effective agent in maintaining its growth and metabolism.

Rain-fed agriculture remains the source of employment for a majority of Ethiopian population, particularly in Dorebafana District, where annual rainfall is low. Perception of climate change and variability supported by local knowledge has helped to advance understanding of climate change and its impacts on agricultural land-use systems. Thus, the overall objective of this study was assessing farmers’ perception of climate change and variability and its impact on agriculture in Umbulo Kajima and Lebu Koromo kebeles of Dorebafana, Sidama region of Ethiopia. A total of 88 sample households from the two kebeles, farmers’ perception were compared with historical climatic data from the closest weather station of the study area. The household survey, focus group discussions and field observation were used as primary data sources in the study area. The data was analyzed by using descriptive statics in Statistical Package for the Social Sciences and multinomial logistic regression model. As data showed, there was the declining and high variability of rainfall in the last three decades In addition, the maximum annual rainfall was observed in 1998, 1755.4 mm and the lowest annual rainfall was recorded in 2015, 537.4 mm in the study area. The focus group discussions and key informant interviews further supported the idea that rainfall in the research area has been falling and very variable over the previous three decades. The finding showed that, temperature increased by 0.1oC over the previous three decade, and socioeconomic factors such sex, age, farming experience, knowledge of the climate, market access, and agro-ecology had an impact on farmers' perceptions of climate change and its impact in agriculture. Therefore awareness creation, increase educational level, sharing experience, scaling up best practice and using new technologies are the best alternatives to minimize the adverse effects of climate change.

Recently, the move from cost-tied to open-access data has led to the mushrooming of research in pursuit of algorithms for estimating aboveground grass biomass (AGGB). Nevertheless, a comprehensive synthesis or direction on the milestones archived or an overview of how these models perform is lacking. This study synthesises the research work from decades of experiments in order to point researchers in the direction of what was done, the challenges faced, as well as how the models perform. A pool of findings from 108 remote sensing-based AGGB studies published from 1972 to 2020 show that about 62% of the remote sensing-based algorithms were tested in the Steppe grasslands, mostly in the temperate climate zone. An uneven annual publication yield was observed with approximately 36% of the research output from Asia whereas countries in the global south yielded few publications (&lt;10%). Optical sensors, particularly MODIS, remain a major source of satellite data for AGGB studies, whilst studies in the global south rarely use active sensors such as Sentinel-1. Optical data tend to produce poor regression accuracies that are highly inconsistent across the studies compared to Radar. Vegetation indices, particularly the Normalised Difference Vegetation Index (NDVI), remain a major predictor variable. Predictor variables such as Sward height, Red edge position and Backscatter coefficients produced slightly consistent accuracies. Deciding on the optimal algorithm for estimating AGGB is daunting due to the lack of overlap in the grassland type, location, sensor types, and predictor variables, signalling the need for further studies around the transferability of remote sensing-based AGGB models.

The 2022-2023 Chilean summer showed increased temperatures and similar burned area, compared to the 2016-2017 season, where more than 500,000 hectares were compromised, mainly in the rural areas. After a brief review, it is revealed that the effects of forest fires on soil and hydrological properties are barely debated in Chile. Here, we showed a climatological analysis where temperature records in the 2016-2017 season were unusual, as well as another unexpected increase in the summer of 2022-2023, resulting in high-severity fires known as ‘mega-fires’ or “storm-fires”. Mega-fires affect forest plantations and native forests mainly from 33º S (Maule Region) to 39º S (Los Ríos Region) and they are expected to become frequent due to climate change, moving from the north to the south. We present an overview of the influence of wildfires on soil components in the most affected areas (inland, Coastal, and Andes ranges), their hydrological impacts, and potential erosion risk due to high winter precipitation. We propose several management practices that could help to prevent or mitigate these events, including pre-and post-fire interventions, such as afforestation and seeding, selective logging, mulching, erosion barriers, soil preparation, and dam monitoring. We argue that any effective plan in fire-prone and affected areas should include a combination of actions taken at the hillslope scale at integral ecosystem management, whose effectiveness should be monitored and verified regionally at the watershed scale.

Bhutan located in the Hindu Kush Himalayan (HKH) region consists of several glaciers and glacial lakes at higher elevations.  With the rapid change in global temperature, glaciers are found to melt at an accelerated rate. This rapid melt of glaciers gets accumulated in weak moraine walls forming a glacial lake, posing a major threat to the downstream communities. As per the Bhutan Glacial Lake Inventory 2021, Bhutan has 567 glacial lakes. Furthermore, the Phochhu basin has the maximum glacial lakes (0.05%) and of which 9 are PDGL. Hence a need for a time monitoring system is imminent. With the availability of free High-resolution Satellite Imageries and Advanced Remote Sensing tools, it has been a sine qua no for monitoring glacial lakes in high areas. Therefore, using the Google Earth Engine and Qgis Platform a semi-automated technique was used to generate glacial lake inventories for Phochhu Sub-basin for the year 2021.  We found out that there are 166 glacial lakes covering an area of 24.051 km2.

Air pollution in urban centers depends directly on anthropogenic activities. The objective of the present study was to predict tropospheric ozone levels from temperature data in the city of Durango, Dgo. Temperature and tropospheric ozone values were obtained from 18 sampling points in the urban area of the city of Durango, of which 15 were obtained by collecting from the Ventusky service and the rest from three fixed monitoring stations established in the city. These values were interpolated in order to determine the spatial values for the entire city. A correlation analysis was performed for three different periods in the day established as follows (24:00-03:00-06:00, 09:00-12:00-15:00 and 15:00-18:00-21:00). Subsequently, a linear regression analysis was performed by time period. The results showed a higher positive correlation between ozone concentration and temperature from 15:00 hrs to 21:00 hrs; likewise, this period showed a higher goodness of fit in the ozone prediction (R2=0.99; RMSE: 1.12 ppbv). Temperature allows spatial prediction of ozone concentrations in urban areas with acceptable accuracy.

Soil aggregates, as the basic component of soil, make great contributions to the stability of soil structure and soil carbon (C) sequestration. Recently, grassland is experiencing continuous grazing, which greatly affects soil aggregation and soil C storage. However, how soil aggregates and soil C in different grassland respond to grazing remain unclear. In this study, three national fenced grassland monitoring field stations which represented mountain meadow (MM), temperate steppe (TS), temperate steppe desert (TSD) were selected, soil samples at 0–10 cm depth of inside and outside the fence were collected to explore the effect of grazing and grassland type on composition, stability and nutrients of soil aggregates. The results showed that the bulk soil organic carbon (SOC), total nitrogen (TN), total phosphorus (TP), available nitrogen (AN) and available phosphorus (AP) varied greatly among the three grassland types, with the highest values in MM. Soil aggregates composition showed significantly response to both grassland type and grazing, especially the proportion of soil aggregates &gt;2 mm, which significantly decreased 51.68% on average in grazing plots compared with fenced plots, whereas sharply decreased in MM and TSD. A significant decrease (on average 25.08%) of the mean weight diameter (MWD) of soil aggregates under grazing was detected across all grassland types. The effect of grazing on nutrients in macroaggregates (&gt;0.25 mm) was greater than that in microaggregates (&lt;0.25 mm). Aggregate-associated SOC concentration decreased under grazing in MM and TSD, however, SOC density showed different response to grazing across all grassland types, with minor effect on MM, decreasing SOC density in TS and increasing on TSD, respectively. The magnitude of grazing effect size on aggregate-associated SOC varied in different soil particle size, with greater response in aggregates &gt; 2 mm and the biggest value in TDS. In addition, correlation analysis showed that MWD of soil aggregates had significant negative correlation with soil bulk density, but significant positive correlation with SOC, TN and TP concentration. Results of RDA showed that BD, soil nutrients were the main influence factors of the composition and stability of aggregates. Overall, grazing had significant influence on soil aggregation, stability and SOC, played a crucial role in grassland soil stability and the accumulation of SOC.

A geophysical technique termed Electrical Resistivity Tomography was applied to identify potential groundwater-bearing zones around Nubutautau village within Viti Levu Island of Fiji. Apparent resistivity data of the subsurface were collected through the electrode assembly along survey lines by injecting current into the subsurface using the ABEM Terrameter LS2. True resistivity data were simulated using the Res2DINVx64 software to produce the final electrical resistivity profiles through an iterative process. Analysis of the resulting modelled profiles revealed the presence of two potential groundwater-bearing zones as potential targets for future drilling. The two targets indicated the presence of potentially saturated vertical fractures through which infiltrating rainwater percolates through the volcanic rock towards a deeper basal aquifer. The identification of the two potential targets demonstrated the great potential of this geophysical technique to effectively inform drilling operations through an evidence-based approach to increase the successful delivery of water security interventions in remote, drought-prone communities of the Pacific.

This work proposes a methodological approach applied to ephemeral gravel-bed streams to verify the change in the magnitude and frequency of hydrological events affecting the morphological dynamics and sediment budget in this type of channel. For the case study the Azohía Rambla, located in southeastern Spain, was chosen, emphasizing the research on two reference riverbed sections (RCRs): an upper one, with a predominance of erosion, and a middle one, where processes of incision, transport, and deposition converge. First, this approach focuses on relationships between peak discharges and sediment budgets during the period 2018 to 2022. For this purpose, water level measurements from pressure sensors, a One-Dimensional Hydrodynamic model, and findings from comparative analyses of high-resolution differential digital elevation models (HRDEM of Difference - HRDoD) based on SfM-MVS and LiDAR datasets were used. In a second phase the GeoWEPP model was applied to the period 1996-2022 in order to simulate runoff and sediment yield at the event scale for the watersheds draining into both RCRs. During the calibration phase a sensitivity analysis was carried out to detect the most influential parameters in the model and to confirm its capacity to simulate peak flow and sediment delivery in the area described above. Values of NS (Nash-Sutcliffe efficiency) and PBIAS (percent bias) equal to 0.86 and 7.81%, respectively, were found in the calibration period, while these indices were 0.81 and -4.1% in the validation period. Finally, different event class patterns (ECPs) were established for the monitoring period (2018-2022), according to flow stage and morphological channel adjustments (overtopping, bankfull and sub-bankfull, and half-sub-bankfull), and then retrospectively extrapolated to stages of the prior simulated period (1996-2018) from their typical sequences (PECPs). The results revealed a significant increase in the number of events and PECPs leading to lower bed incision rates and higher vertical accretion, which denotes a progressive increase in bed armoring and bank erosion processes.

The present study describes the development and application of a computer model of the national electricity system for the Caribbean dual-island nation of Antigua and Barbuda to investigate the cost-optimal mix of solar photovoltaics (PV), wind, and in the most novel contribution, concentrating solar power (CSP). These technologies, together with battery and hydrogen energy storage, can enable the aim of achieving 100% renewable electricity and zero carbon emissions. The motivation for this study was that while most nations in the Caribbean rely largely on diesel fuel or heavy fuel oil for grid electricity generation, many countries have renewable resources beyond wind and solar energy. Antigua and Barbuda generates 93% of its electricity from diesel-fueled generators and has set targets of becoming a net-zero nation by 2040 and having 86% renewable energy generation in the electricity sector by 2030, but the nation has no hydroelectric or geothermal resources. The modeled, optimal mix of renewable energy technologies presented here was found for Antigua and Barbuda by assessing the levelized cost of electricity (LCOE) for systems comprising various combinations of energy technologies and storage. Other factors were also considered, such as land use and job creation. It was found that 100% renewable electricity systems are viable and significantly less costly than current power systems, and that there is no single defined pathway towards a 100% renewable energy grid, but several options are available.

Visual data on the geographic distribution of carbon storage helps policy maker to formulate countermeasures on global warming. However, Taiwan, as an island showing diversity in climate and topography, had lacked valid visual data in distribution of forest carbon storage between the last to forest surveys (1993-2015). This study established a model to achieve an estimation that capable to demonstrate the distribution of forest carbon storage. This model uses land use, stand morphology, carbon conversion coefficient databases accordingly for 51 types of major forest in Taiwan. An estimation on 2006 was conducted and shows an overall carbon storage of 165.65 Mt C, with forest carbon storage per unit area of 71.56 t C ha–1, where natural forests and plantations respectively contributed of 114.15 Mt C (68.9%) and 51.50 Mt C (31.1%). By assuming no change in land use type, the carbon sequestration from 2006 to 2007 by the 51 forest types was estimated to be 5.21 Mt C yr–1 using historical tree growth and mortality rates. The result reflects the reality of the land use status and event of coverage shifting with time by combining to the two forest surveys in Taiwan.

Corn is the main agricultural product and has been produced in Kazakhstan as important nutrition in human and animal food. The research results shown in the article, the fact of increasing the sustainability of corn production is formulated, methodological approaches to assessing the level of sustainability are developed, and criteria are defined for the main indicators of sustainability and efficiency of corn production. The world's corn production was 1,223 million tons in the 2021/22 season. Kazakhstan's corn production average was 1,1 million tons and the production area are 206,870 in the 2021/22 season. The yield per hectare was 5,985 kg in the 2021/22 season. Corn consumption was 1170.5 million tons and exported was 180.1 m.tons of corn in the 2021/22 season in Kazakhstan. The purpose of this study is a determination of sustainable developments of corn consumption and production in Kazakhstan and worldwide between the 2011/12 and 2021/22 seasons. Statistical data have been obtained from the International Grain Council, FAOSTAT, USDA, PhD diploma thesis of the article's author, Bureau of National Statistics. Data obtained have been shown in the tables issued by the use of percentage and index calculations. The study analyzed a major factor affecting supply and demand, sustainable development of corn production and market prices.

Due to the special terrain of Urumqi (in the valley area), which often triggers strong foehn weather, and causes huge losses to local people's lives and social economy. This study uses in-situ surface meteorological variables (including the hourly temperature, pressure, humidity, wind, etc.) from the Urumqi Meteorological Station (downstream station, DS) and the Dabancheng Meteorological Station (upstream station, US) in the Middle Tianshan Valley and NCEP/NCAR reanalysis data from 2008 to 2022. A dataset of the foehn weather process at DS in the past 15 years is established and the variation patterns of each meteorological variable during the process of foehn is analyzed. Based on the physical mechanism of the occurrence of foehn, a three-element identification standard for foehn in Urumqi is established by comparing and analyzing the variation of wind direction (WD), wind speed (WS), and the difference of potential temperature (Δθ) between DS and US during the period of foehn and non-foehn from 2013 to 2022, namely: 94°≤ 2-minute average WD ≤168°, 2-minute average WS ≥2.0 m/s, and Δθ between DS and US ≥ 0.29 K. According to the test and evaluation, the three-element identification standard has an accuracy of 82.96%, and a hit rate of 89.50% for the occurrence of foehn in Urumqi from 2008 to 2012. Moreover, the hit rate of foehn identification is 100% for strong wind or above (i.e., 2-minute average WS ≥10.8 m/s) WS. In addition, combined with two predictors of sea-level pressure difference (ΔP) and Δθ between DS and US, forecasting foehn can be more accurately predicted than a single forecasting factor. When ΔP ≤ -12 hPa and Δθ≥5 K, the probability of the occurrence of foehn is more than 90%. This study provides certain reference and application value for the weather forecasting operation of foehn.

Soil amendments with composted organic materials are recommended to increase soil organic matter (SOM), promote soil fertility, and the Circular Economy. Growing areas of hedged olive groves in southern Iberia peninsula generate huge amounts of olive leaves whose potential as soil organic amendment is not fully studied. An experimental field trial in a hedged olive grove (cv. “Cobrançosa”) was set up near Portalegre, Portugal, to test a compost of olive leaves plus sheep manure (2:1) applied in the row, at soil surface. Three nominal rates (0 or control, 2.5 and 5.0 kg m-2) were used, in a complete randomized block setup (3 treatments, 3 replicas, 9 plots) and soil chemical properties of layers 0-5, 5-15, and 15-30 cm deep were annually monitored. Results (mainly in layer 0-5 cm) showed increases in total N, carbon of the particulate organic matter (POM-C), permanganate oxidizable carbon (POX-C), extractable phosphorus, and zinc, after one year, and increases in soil organic carbon (SOC), C-stock, pHKCl, extractable phosphorus, and zinc, after two years. POX-C was the most sensitive SOM-related indicator, showing increases up to 30 cm deep after one year. This compost improved soil fertility, but should be monitored over longer periods of time, namely for SOC and extractable zinc content.

Glitter particles are considered a model of microplastics, which are used in a wide range of products. In this study, we evaluated the toxicity of green and white glitter dispersions on the embryonic development of the sea urchins Echinometra lucunte, Arbacia lixula, and the mussel Perna perna. The Toxicity Identification and Evaluation (TIE) approach was used to identify possible chemicals related to toxicity. Glitter dispersions were prepared using 0.05% ethanol. The tested dispersions ranged from 50 to 500 mg/L. The white glitter was composed of a vinyl chloride-methyl acrylate copolymer. The effective concentrations of green glitter to 50% embryos (EC50) were 246.1 (235.8 – 256.4) mg/L to A. lixula, 23.0 (20.2 - 25.8) mg/L to P. perna and 105.9 (61.2 - 150.2) mg/L, whereas the EC50 of white glitter to E. lucunter was 272.2 (261.5 – 282.9) mg/L. The EC50 for P. perna could not be calculated; however, the lowest effect concentration was 10 mg/L. The filtered suspension of green glitter had Ag levels exceeding the legal standards for marine waters. TIE showed that metals, volatiles, and oxidant compounds contribute to toxicity. The results showed that glitter may adversely affect marine organisms; however further studies are necessary to determine its environmental risks.

Dye wastewater containing bisphenol A (BPA) and dyes as pollutants have not been adequately studied. Our previous study revealed that thermoplastic polyurethane (TPU) nanofiber membranes (NFMs) modified by the addition of polyethyleneimine (PEI) and polydopamine (PDA) satisfactorily adsorb dyes. Herein, we first optimized the synthesis conditions for such membranes, noting a PEI:PDA monomer ratio of 2:2 and a deposition time of 48 h to be optimal. Experiments using these membranes revealed that binary systems containing BPA and the dyes (Congo red (CR), Eosin yellow (EY), or sunset yellow (SY)) exhibit three adsorption behaviors. CR and BPA compete with each other for adsorption sites, decreasing the maximum adsorption capacity (Qmax) for CR 208.3 mg/g (in a monomeric system) to 182.4 mg/g, whereas for BPA, it decreased from 26.7 to 22.8 mg/g. The adsorption rates for CR and BPA decreased from 0.002 min−1 and 0.331 min−1 in the monomeric systems to 8.37 × 10−4 min−1 and 0.072 min−1, respectively, in the binary CR–BPA system, exhibiting antagonistic effects. When EY and BPA coexist, Qmax for EY increased from 60.0 (monomeric) to 71.9 mg/g, whereas that for BPA increased from 35.6 to 43.2 mg/g, showing a synergistic effect due to the possible bridging effect. The adsorption sites for SY and BPA are independent of each other. Thus, PDA/PEI TPU NFMs exhibit the potential for removal of dye–BPA composites, whereas binary systems containing BPA with different dyes are adsorbed differently.

To prevent CO2 leakage and ensure the safety of long-term CO2 storage, it is essential to investigate the flow mechanism of CO2 in complex pore structures at the pore scale. This study focuses on reviewing the experimental, theoretical, and numerical simulation studies on the microscopic flow of CO2 in complex pore structures during the last decade. For example, advanced imaging techniques, such as X-ray computed tomography (CT) and nuclear magnetic resonance (NMR), are used to reconstruct the complex pore structures of rocks. Mathematical methods, such as Darcy's law, Young–Laplace’s law, and the Navier-Stokes equation, are used to describe the microscopic flow of CO2. Numerical methods, such as the lattice Boltzmann method (LBM) and pore network (PN) model, are used for numerical simulation. The application of these experimental and theoretical models and numerical simulation studies is discussed, considering the effect of complex pore structures. Finally, future research is suggested to focus on: (1) Conducting real-time CT scanning experiments of CO2 displacement combined with the developed real-time CT scanning clamping device to realize real-time visualization and provide quantitative description of the flow behavior of CO2 in complex pore structures; (2) The effect of pore structures change on the CO2 flow mechanism caused by the chemical reaction between CO2 and the pore surface, the flow theory of CO2 considering wettability and damage theory in a complex pore structures; (3) The flow mechanism of multi-phase CO2 in complex pore structures; (4) The flow mechanism of CO2 in the pore structures at multiscale and the scale upgrade from microscopic to mesoscopic to macroscopic. Generally, this study focuses on reviewing the research progress of CO2 flow mechanisms in complex pore structures at the pore scale and affords an overview of potential advanced developments to enhance the current understanding of CO2 microscopic flow mechanisms.

To realize the energy recovery of wheat straw, the pyrolysis behavior of wheat straw was studied at three heating rates (10, 20, and 30 K/min) based on thermogravimetric analysis (TG–DTG). Kinetics and thermodynamics were analyzed using Flynn–Wall–Ozawa (FWO) and Kissinger–Akahira–Sunose (KAS) model-free methods, and reaction mechanism was determined using Coats–Redfern (CR) model-fitting method. The results show that there are three weightlessness stages in the pyrolysis process, of which the second stage was the main weightlessness stage and two distinct peaks of weightlessness were observed in this stage. With increasing heating rate, the main pyrolytic weightlessness peaks of DTG curve shifts to higher temperature. The pyrolysis activation energy calculated by FWO and KAS methods are 165.17–440.02 kJ/mol and 163.72–452.07 kJ/mol, and the pre-exponential factor vary in the range of 2.58×1012–7.45×1036 s-1 and 1.91×1012–8.66×1037 s-1, respectively. The thermodynamic parameters indicates that wheat straw has the favorable conditions for product formation and containes potential energy to be utilized for bioenergy production, its pyrolysis reaction was non-spontaneous and the energy output is stable. CR method analysis shows that the A1/3 random nucleation model is the most suitable mechanism to characterize the pyrolysis process, and random nucleation may be in charge of the main pyrolysis stage. This study can provide a theoretical basis for the thermochemical conversion and utilization of wheat straw.

In response to the problem of increasing climate change and energy security, investment in renewable energy sources has increased significantly both in Europe and globally. Wind and solar power plants are expected to be the largest contributors to global decarbonization, ranking first and second in projected capacity by 2050. Since all power plants have some impact on the environment, this also applies to photovoltaic power plants. Because of the large capacities projected for PV installed capacity, their environmental impacts should be evaluated. The environmental impacts of PV power plants change over time. Improving the manufacturing technology of PV system components, increasing the efficiency of solar cells, and using materials that are less harmful to the environment will reduce these impacts. Manufacturing PV system components is a highly energy-intensive process that involves greenhouse gas emissions. As new renewable energy capacity is built, the amount of "green" electricity on the grid increases, reducing CO2 emissions per kWh consumed. The objective of this paper is to analyze the current status of the environmental impact of PV power plants under these changing conditions in terms of CO2 emissions, land use, pollutant and noise emissions, and water consumption. The capacity installed to date will reach the end of its lifetime by 2050, which means that the amount of waste associated with it will increase over time. This can have a significant impact on the environment, which is why part of the work is dedicated to this problem. In addition to the available information from the literature, in the part related to land use, the authors also made their own estimates based on data on newly installed PV power plants and PV modules available on the market. The results of the analysis show that there is enough land both in Europe and worldwide to install the planned capacities of rooftop and ground-mounted PV power plants. CO2 emissions are at the same level as for concentrated solar power, with a decreasing trend. Pollutant emissions, noise and water consumption are not a major problem compared to other types of power plants. Overall, it can be concluded that the expansion of PV capacity has a very positive impact on the environment.

The development of a decision framework for landscape governance and management has become one of the prioritised policy instruments for actualising policy objectives relating to agri-food system, biodiversity conservation, nature restoration, environmental management, climate change mitigation and adaptation, net zero greenhouse gas emissions, and the transition to renewable energy supplies in the United Kingdom (UK). However, the landscape lens in policy-making is challenging because of the diverse landscape archetypes, environmental problems, and diverging policy targets that it must address. This highlights the importance of having a robust, evidence-based landscape decisions framework. To address this issue, this study undertakes a systematic review and transdisciplinary synthesis of research outputs from the Landscape Decisions Programme (LDP). This study compiles and synthesizes outputs from the LDP projects in the context of the relevant literature to develop an understanding of the relationships among the emerging evidence with respect to decision-making for more sustainable and multifunctional landscapes. The synthesis analyzed the drivers of landscape decisions, and methodological approaches used to generate evidence for decision-making. The emerging themes from the synthesis were distilled into five principles that can be used as a basis for a roadmap towards the development of a holistic landscape decisions framework.

The sedimentary characteristics of the special interlayer contained in the section of the Sparking Lake dam revealed by the 8.8 Jiuzhaigou earthquake in 2017 are obviously different from the tufa in the dam body, and they are considered to be prehistoric flood relics. Based on the study of the particulate matter from the 8.8 Jiuzhaigou earthquake, this paper combines comparative petrographic, mineralogical, geochemical and chronological studies of the special interbedded sediments of the Sparking Lake dam with other genetic samples to obtain homology information and genetic links, as well as to explore the tufa depositional dynamics and earthquake disaster subsidence. The palaeoseismic benefit in the discontinuity layer is explored, and the palaeoseismic information embedded in the profiles is extracted, providing a new idea to reconstruct the palaeoseismic events in the tufa deposition sequence. According to X-ray diffraction, laser particle size analysis and scanning electron microscope experiments, the particulate matter in the Jiuzhaigou mountains has its own specific mineralogical characteristics. The mineral composition of the particulate matter is basically calcite. The particle size is large, and the single particle is mostly angular and subangular. The fracture morphology observed under the single particle microscope is uneven, showing the characteristics of dust caused by earthquake disasters. Geochemical analysis data show that the provenance of various types of particles in the same area is stable, indicating the homology of terrestrial carbonate sedimentation in the karst system. Combined with mineralogy and grain size morphology, the interbedded particles in the tufa depositional profile have the potential application of palaeoseismic archives to record extreme seismic events. The palaeoseismic date was inferred from the chronological data of special interlayered sediments in the tufa dam body. Therefore, the tufa bedding can be related to the palaeoearthquake, and the special interlayer of the tufa section can be used to reconstruct palaeoearthquakes.

Filamentous manganese (Mn) oxide particles, which occur in the suboxic zone of stratified waterbodies, are important drivers of diverse elemental cycles. Although these particles are considered to be bacteriogenic, the environmental factor responsible for their formation has not been identified. Based on this study of laboratory cultures of a model Mn(II)-oxidizing bacterium, the supply of algal extracellular polymeric substances (EPS) was shown to stimulate Mn(II) oxidation and thus the production of filamentous Mn oxide particles. This observation was consistent with results obtained for naturally occurring particles collected from a near-bottom layer (depth of ~90 m) in the northern basin of Lake Biwa, Japan, that is, most Mn particles resembling delta-MnO2 were associated with an EPS-like gelatinous matrix, which contained dead algal cells and was lectin-stainable. In the lake water column, EPS produced by photosynthesis sank to the bottom layer. The analysis of the quality of water samples, which have been collected from the study site for 18 years, reveals that the annual average total phytoplankton biovolume in the surface layer correlates with the density of filamentous Mn particles in the near-bottom layer. Among different phytoplankton species, green algae appeared to be the key species. The results of this study suggest that algal EPS production induces the formation of filamentous Mn oxide particles in the near-bottom layer of the northern basin of Lake Biwa.

GNSS time series prediction plays a significant role in monitoring crustal plate motion, landslide detection, and maintenance of the global coordinate framework. Long Short-Term Memory (LSTM), a deep learning model has been widely applied in the field of high-precision time series prediction especially when combined with Variational Mode Decomposition (VMD) to form the VMD-LSTM hybrid model. To further improve the prediction accuracy of the VMD-LSTM model, this paper proposes a dual variational modal decomposition long short-term memory (DVMD-LSTM) model to effectively handle the noise in GNSS time series prediction. This model extracts fluctuation features from the residual terms obtained after VMD decomposition to reduce the prediction errors associated with residual terms in the VMD-LSTM model. Daily E, N, and U coordinate data recorded at multiple GNSS stations between 2000 and 2022 are used to validate the performance of the proposed DVMD-LSTM model. The experimental results demonstrate that compared to the VMD-LSTM model, the DVMD-LSTM model achieves significant improvements in prediction performance across all measurement stations. The average RMSE is reduced by 9.86%, and the average MAE is reduced by 9.44%. Furthermore, the average accuracy of the optimal noise model for the predicted results is improved by 36.50%, and the average speed accuracy of the predicted results is enhanced by 33.02%. These findings collectively attest to the superior predictive capabilities of the DVMD-LSTM model, thereby enhancing the reliability of the predicted results.

Taking Shanxi Province, a typical energy region in China, as the research object, data on economic development quality and environmental pollution intensity from 2001 to 2021 were selected. Linear regression, numerical simulation, and Pearson correlation coefficient were used to analyze the evolution characteristics of economic development quality and environmental pollution intensity in Shanxi Province in the past 20 years, and to explore the relationship between economic development and environmental pollution. The results indicate that since 2001, Shanxi Province has made long-term progress in economic development, with GDP increasing by nearly 10 times and an average annual growth rate of around 7%. In the past 20 years, the main pollutants have shown a trend of increasing first and then decreasing steadily, with a turning point occurring during the "12th Five Year Plan" period. This shows that the environmental policies and investments of the Chinese and Shanxi provincial governments in the past 10 years have been effective in the new era. The numerical simulation curve results show that the per capita GDP exhibits a classic inverted "U" curve relationship with wastewater and SO2 emissions, with a turning point occurring at around 20000 yuan per capita GDP; However, there is a monotonic decreasing trend with Chemical oxygen demand and ammonia nitrogen emissions, and a monotonic increasing trend with solid waste generation. There is no turning point yet. The correlation analysis results further support the fitting curve conclusion.

This paper evaluated the quality and suitability of surface water in the Vaalharts area, South Africa, for human consumption, drinking, and irrigation purposes. Water quality constituents include water pH, EC, TDS, HCO3-, Cl-, SO4, Mg, Ca, k, Na, NO3, F, Fe, PO4, As, Al, Mn, Cr, Cu, Zn, B, Cd, Hg, Pb, N, Sb, Se, and the biological parameter included E. coli along surface waters as well as canals and dams. Sodium Adsorption Ratio, Sodium Percentage, Permeability Index, Residual Sodium Carbonate, Kelley’s Ratio, Magnesium Hazard, and Potential salinity irrigation water parameters indicated that the majority of the water samples are suitable for irrigation. The water quality index values showed that the majority of the samples are unsuitable for drinking but suitable for irrigation and industrial uses. E. coli in the surface water samples in the study area show unsafe water quality with high and very high risk for human health. Based on the classifying criterion of the Heavy Metal Pollution Index and Heavy Metal Evaluation Index, all the water samples are above the critical limit, therefore, unsuitable for human consumption. The carcinogenic risk (CR) concentrations of As, Cr and Cd were above the target risk.

Pore fluid pressure is very important to the generation, migration and accumulation of petroleum. The previous studies indicate that the Chezhen sag region is typically characterized by pore fluid overpressure (the difference between pore fluid pressure and hydrostatic pressure). To date, the formation mechanism of pore overpressure and the accumulation regularity of “upper source-lower reservoir” type in this region remains unknown. In order to investigate these problems, a 2-D finite element model is established with regards to the fluid-solid coupling in Chegu 25 block of Chezhen depression, fully considering the existing seismic, logging data and regional tectonic stress environment. Meanwhile, we calculate the abnormal overpressure generated at the source rock during hydrocarbon generation and the process of hydrocarbon migration and accumulation along the faults, analyzing the dynamic conditions of hydrocarbon downward accumulation. The results show that overpressure can accelerate migration of hydrocarbon and improve the efficiency of hydrocarbon accumulation. However, when the overpressure is too large, tensile fractures and shear fractures may occur, resulting in hydrocarbon dissipation, and changing the results of oil and gas accumulation. The overpressure at the source rock is mainly caused by hydrocarbon generation, while the overpressure at the reservoir is primarily created by unbalanced compaction. As the dominant channel of hydrocarbon migration, overpressure will change the direction and path of hydrocarbon migration in the fault. Therefore, the “upper source-lower reservoir” hydrocarbon accumulation model is strongly explained by the high permeability of faults and the presence overpressure. In summary, the simulated overpressure results are in good agreement with the mud weight equivalent overpressure and the drill stem tests (DSTs).

It is a challenging and meaningful task to carry out drone-based livestock monitoring in high-altitude and cold regions. The purpose of AI is to execute automated tasks and to solve practical problems in actual applications by combining the software technology with the hardware carrier to create integrated advanced devices. Only in this way, the maximum value of AI could be realized. In this paper, a real-time tracking system with dynamic target tracking ability is proposed. It is developed based on the tracking-by-detection architecture using YOLOv7 and DeepSORT algorithms for target detection and tracking, respectively. To address the existing problems of the DeepSORT algorithm, the following two optimizations are made: (1) Optical flow is used to compensate the Kalman filter for improvement of the prediction accuracy; (2) A low-confidence trajectory filtering method is adopted to reduce the influence of unreliable detection on target tracking. In addition, an visual servo controller for the UAV is designed to enable the automated tracking task. Finally, the system is tested using the Tibetan yaks living in the Tibetan Plateau as the tracking targets, and the results reveal the real-time multiple tracking ability and the ideal visual servo effect of the proposed system.

40 years of cloud observations are available globally from satellites allowing derivation of climate data records (CDRs) for climate change studies. The aim of this study is to investigate how stable these cloud CDRs are and whether they qualify stability requirements recommended by the WMO’s Global Climate Observing System (GCOS). We also investigate robust trends in global total cloud amount (CA) and cloud top temperature (CTT) that are significant and common across all CDRs. The latest versions of four global cloud CDRs, namely CLARA-A3, ESA Cloud CCI, PATMOS-x and ISCCP-HGM, are analysed. This assessment finds that all three AVHRR based cloud CDRs satisfy even the strictest GCOS stability requirements for CA and CTT when averaged globally. While CLARA-A3 is most stable in global averages, PATMOS-x offers the most stable CDR spatially. While we find these results highly encouraging, there however remain large spatial differences in the stability of and across the CDRs. All four CDRs continue to agree on the statistically significant decrease in global cloud amount over the last four decades, although this decrease is now weaker compared to the previous assessments. This decreasing trend is stabilizing or even reversing in the last two decades; the latter is seen also in MODIS-Aqua and CALIPSO GEWEX datasets. Statistically significant trends in CTT are observed in global averages in the AVHRR-based CDRs, but the spatial agreement in the sign and the magnitude of the trends is weaker compared to those in CA. We also present maps of Common Stability Coverage and Common Trend Coverage that could provide a valuable metric to carry out an ensemble-based analysis of the CDRs.

Noise model selection criteria has a significant impact on identifying the stochastic noise proper-ties of any GNSS daily coordinate time series. The low-frequency random walk noise existing in these time series could lead to overestimation of the tectonic rate, so it is of great significance to accurately detect the random walk component. This study focuses on noise model estimation cri-terion (BIC_tp) derived from the AIC and the BIC by introducing 2π factors. It is more sensitive to abnormal steps (random jumps). Using observation data from 72 GNSS stations from 1992 to 2022 and simulated data, four combined noise models are used to explore the impacts of time se-ries lengths (ranging from2 to 24 years) and data loss (between 2% and 30%) on noise models and velocity estimation. The results show that as the time length increased, the selected optimal noise model, and the estimated uncertainty of the tectonic trend with different data gap, gradually con-verge. When the time length is short (less than 8 years), it could lead to the FNRWWN, FNWN, and PLWN models being mistakenly estimated as GGMWN models, thereby affecting the accura-cy of determining the station velocity parameters. When the time length is 12 years, the RW noise component is more probably detected, As the time length increases, the impact of RW on velocity uncertainty is weakened. Finally, we conclude that for a time series with a minimum time length of 12 years, both the selection of the optimal stochastic noise model and the estimation of the ve-locity parameters are reliable.

Due to the energetic transition at course, new geological exploration technologies are needed to discover mineral deposits containing critical materials such as lithium (Li). The vast majority of European Li deposits are related to Li–Cs–Ta (LCT) pegmatites. Literature review indicates that conventional exploration campaigns are dominated by geochemical surveys and related exploration tools. However, other exploration techniques must be evaluated namely remote sensing (RS) and geophysics. This work presents the results of the INOVMINERAL4.0 project obtained through alternative approaches to traditional geochemistry that were gathered and integrated into a webGIS application. The specific objectives were to: (i) assess the potential of high-resolution elevation data; (ii) evaluate geophysical methods, particularly radiometry; (iii) establish a methodology for spectral data acquisition and build a spectral library; (iv) compare obtained spectra with Landsat 9 data for pegmatite identification; and (v) implement a user-friendly webGIS for data integration and visualization. Radiometric data acquisition using geophysical techniques effectively discriminated pegmatites from host rocks. The developed spectral library provided valuable insights for space-based exploration. Landsat 9 data accurately identified known LCT pegmatite targets, compared to Landsat 8. The user-friendly webGIS facilitated data integration, visualization, and sharing, supporting potential users in similar exploration approaches.

Rapid urbanization and climate change effects may cause dramatic change of ecosystem functions in cities, thereby inevitably affecting the growth performance of ancient trees. Few studies have explored species diversity and spatial differentiation in Benin urban area. Here, we took Cotonou city to do that. The objective of the study conducted in the city of Cotonou, was to determine the predominant level of plant diversity in the city's land-use units. The urban green frame was subdivided into six land use units, namely establishments, residences, green spaces, commercial areas, administrative areas, and roads. The forest inventories were carried out in 149 plots with surfaces evaluated at 2500 m2 each. A total of 62 tree species in 55 genera and 27 families were recorded. The results show that the flora of the city of Cotonou is characterized by a strong preponderance of exotic species. The most abundant species with high ecological importance (IVI) in the different type of land use of the city are Terminalia catappa (IVI=121.47%), Terminalia mentally (IVI=90.50%), Mangifera indica (IVI=64.06%) and Khaya senegalensis (IVI=151.16%). This study shows that a directed development of this urban vegetation could improve the resilience of urban life to climate hazards through the provision of urban ecosystem services, potential ecological infrastructure foundations and urban nature-based solutions.

To date, only a few studies focused on carbon monoxide (CO) production during waste composting; all targeted on CO inside piles. Here, the CO net emissions from compost piles and the assessment of worker’s occupational risk of exposure to CO at large-scale composting plants are shown for the first time. CO net emissions were measured at two plants processing green waste, sewage sludge, or undersize fraction of municipal solid waste. Effects of the location of piles (hermetised hall vs. open yard) and turning (before vs. after) were studied. Higher CO net emission rates were observed from piles located in a closed hall. The average CO flux before turning was 23.25 and 0.60 mg‧m-2‧h-1 for hermetised and open piles, respectively, while after – 69.38 and 5.11 mg‧m-2‧h-1. The maximum CO net emissions occurred after the compost was turned (1.7x to 13.7x higher than before turning). The top sections of hermetised piles had greater CO emissions compared to sides. Additionally, 5% of measurement points of hermetised piles switched to ‘CO sinks’. The 1-h concentration in hermetised composting hall can reach max. ~50 mg CO∙m-3 before turning, and &gt;115 mg CO∙m-3 after, exceeding the WHO thresholds for a 1-h and 15-min exposures, respectively.

The gradual decline of the Aral Sea’s water level over the past five decades poses a huge environmental problem in the heart of Central Asia. Uzbekistan, once blessed with abundant water resources, now struggles with water scarcity in certain regions. While global environmental issues contribute to some degree to this dilemma, irrigation mismanagement plays a central role. This study focuses on the widespread problem of irrigation mismanagement in Uzbekistan and specifically addresses the rural district of Oltinsoy in the southern province of Surkhandarya. The main objective of this research project is to propose effective measures that can alleviate the pressing problem of water scarcity in the region while emphasizing the urgent need for well-executed projects and careful maintenance to ensure long-term sustainability at the local level. It is important to note that this study does not include an examination of the impact of global warming on the decline of water resources in Uzbekistan.

Madagascar is a biodiversity hotspot with a long history of trading in its wildlife, especially its hyper diverse Amphibian taxa. Due to globally raised concerns over the conservation for harvested amphibian species on Madagascar, CITES was introduced as a global mechanism to monitor and regulate the trade. Utilising data collated from the CITES Trade database, this study sought to investigate the trade and CITES effectiveness in managing the trade. Over the 28 year period investigated, 20 known amphibian species were exported from Madagascar with a total of nearly 271,000 individuals. Formal descriptions of Malagasy amphibian species has and continues to increase greatly over time, there has not been a concomitant, longitudinal relationship in the numbers of individuals traded. Overall, the numbers of individuals traded has declined over time but, where assessments were provided by the IUCN Redlist, population declines were reported in all but one species of Malagasy amphibian. Mantella (97.5%) continue to dominate the trade with certain, high conservation concern species continuing in the trade. Despite early concerns over the effectiveness of CITES actions, after concerted efforts it appears that CITES actions were having an impact in regulating the trade. However, going forward, concerns remain over the appropriateness of the quotas set and the robustness of their underpinning NDFs. Furthermore, with the increase in recognised species raises the potential for incorrect species labelling on CITES permits that needs attention.

The Puuc Biocultural State Reserve (PBSR is an unique model for tropical dry forest conservation in Mexico. Preserving forest biodiversity and carbon within the PBSR depends on the mainte-nance of low impact productive activities coordinated by multiple communal and private land-owners. In this study, we used state-of-the-art remote sensing data to investigate past spatial patterns in forest clearing dynamics and its relation to forest carbon density and forest plant species richness and diversity in the context of the forest conservation goals of the PBSR. We used a Landsat-based continuous change detection product for the 2000-2021 period and compared it to carbon density and tree species richness models generated from ALOS-2 PALSAR 2 imagery and national scale forest inventory data. The estimated error-adjusted area of detected annual forest clearings from the year 2000 until the year 2021 was 230,511 ha in total (+19,979 ha). The analysis of annual forest clearing frequency and area suggests that although forest clearing was significantly more intensive outside of the PBSR than within the PBSR during the entire 2000-2021 period, there is no evidence suggesting that the frequency and magnitude of forest clearing has changed over the years after the creation of the PBSR in 2011. An emergent hotspot analysis shows, however, that high spatiotemporal clustering of forest clearing events (hotspots) during the 2012-2021 pe-riod was less common than prior to 2011 and these more recent hotspots have been confined to areas outside the PBSR. After comparing forest clearing events to carbon density and tree species richness models, results show that land owners outside the PBSR often clear forests with lower carbon density and species diversity than land owners inside the PBSR. This suggests that, compared to land owners outside the PBSR, land owners within the PBSR might be practicing longer fallow periods allowing forests to attain higher carbon density and tree species richness and hence better soil nutrient recovery after land abandonment. In conclusion, our results show that the PBSR effectively acted as a stabilizing forest management scheme during the 2012-2021 period minimizing the impact of productive activities by lowering the frequency of forest clearing events and preserving late secondary forests within the PBSR. We recommend the continuation of efforts for providing alternative optimal field data collection strategies and modeling techniques to spatially predict key tropical forest attributes. The combination of these models with contin-uous change detection datasets will allow to reveal underlying ecological processes and generate information better adapted to forest governance scales.

In order to better understand the extent to which global climate variability is linked to the frequency and intensity of heat waves and overall changes in temperature throughout the United States (US), correlations between long-term monthly mean, minimum, and maximum temperatures measured at sites throughout the contiguous US and low-frequency variability of multiple climate indices (CIs) are analyzed over the period 1948 to 2018 using correlation analysis. The Pearson’s correlation coefficient is used to assess correlation strength, while Leave-One-Out Cross-Validation and a bootstrapping technique (p-value) are used to address potential serial and spurious correlation and assess the significance of each correlation. Three parameters defined the sliding windows over which surface temperature and CI values were averaged: window size, lag time between the temperature and CI windows, and the beginning month of the temperature window. A 60-month sliding window size and 0 lag time resulted in the strongest correlations overall; beginning months were optimized on an individual site basis. Strong (r &gt;= 0.60) and significant (p-value &lt;= 0.05) correlations were identified. The Western Hemisphere Warm Pool (WHWP) and El Niño/Southern Oscillation (ENSO) exhibited the strongest links to temperatures in the western US, tropical Atlantic sea surface temperatures to temperatures in the central US, the WHWP to temperatures throughout much of the eastern US, and atmospheric patterns over the northern Atlantic to temperatures in the Northeast and Southeast. The final results were compared to results from previous studies focused on precipitation and coastal sea levels. Regional consistency was found regarding links between the northern Atlantic and overall weather and coastal sea levels in the Northeast and Southeast as well as on weather in the upper Midwest. Though the MJO and WHWP revealed dominant links with precipitation and temperature, respectively, throughout the West, ENSO revealed consistent links to sea levels and surface temperatures along the West Coast. These results help focus future research regarding specific mechanisms of climate variability that appear the exhibit strong links to US regional weather and sea level variability and prediction.

The need to address climate change and establish sustainable urban environments has driven increased efforts in Europe to develop climate-neutral cities. This study highlights the importance of integrating solar energy technologies and nature-based solutions as key strategies to achieve climate neutrality. By examining current practices, emerging trends, and case examples, it explores the benefits, challenges, and prospects associated with the integration of solar energy and nature-based solutions in urban contexts. The study presents a pioneering approach to assess the urban heat and climate change mitigation benefits of combining building-integrated photovoltaics and nature-based solutions specifically within the European context. The results emphasize the synergistic relationship between nature-based components and solar conversion technology, identifying effective combinations for different climatic zones. In warmer regions of Southern Europe, strategies like rooftop photovoltaics on cool roofs, photovoltaics shadings, green walls, and urban trees have demonstrated effectiveness. Conversely, mid- and high-latitude European cities have seen positive impacts through the integration of rooftop photovoltaics and photovoltaics facades with green roofs and green spaces. As solar cell conversion efficiency improves, the environmental impact of photovoltaics is expected to decrease, facilitating their integration into urban environments. The study emphasizes the importance of incorporating water bodies, cool pavements, spaces with high sky-view factors, and effective planning in urban design to maximize resilience benefits. It also highlights the significance of prioritizing mitigation actions in low-income regions and engaging citizens in the development of social photovoltaics positive energy houses, resilient neighbourhoods, and green spaces. By adopting these recommendations, European cities can lead the way in creating climate-neutral urban environments that prioritize clean energy, nature-based solutions, and the overall well-being of residents. The findings underscore the need for a multidisciplinary approach that combines technological innovation, urban planning strategies, and policy frameworks to effectively achieve climate neutrality in European cities.

This paper investigates urban microclimate in relation to the typical major streets and mobility layout in Turin, i.e. boulevards with lateral minor roads, called “controviali”, an almost unique urban mobility layout. The aim is to examine the possibility of intervention in relation to the type and scope of mobility for microclimate mitigation and climate adaptation purposes. To this, this paper evaluates to which extent urban morphology and mobility features contribute to determining microclimatic conditions, to finally identify site-specific prioritised strategies to cope with its mitigation. This research is structured in two phases. The first phase is dedicated to urban-scale analysis of the streets with “controviali”, resulting in the creation of a database containing their properties and typology, to finally derive six clusters of boulevards. The second phase involves the selection of one representative case study per cluster and simulation of their microclimate conditions, performed by the software ENVI-met. The results are discussed in relation to the parameters proven in the prior literature review to have a major impact on the microclimate. The assessment of the results indicated which elements affect the climatic conditions the most, allowing for the proposal of different prioritised mitigation strategies in the conclusion.

Mass mortality events and anthropogenic impacts were increasingly documented affecting Paramuricea clavata (Risso, 1826) during the last decades. These impacts enhance the settling of epibiontic organisms on the injured colonies. The epibiosis was studied by photographic sampling carried out on the granitic outcrops of the Tavolara Channel within the Tavolara-Punta Coda Cavallo Marine Protected Area (NE Sardinia) between 2017-2023 at 35-55 m. The number of colonies and percent surface involved in epibiosis, the specific richness of the epibiontic community and the temporal evolution of the phenomenon were investigated. Almost all the investigated gorgonians (93%) showed parts involved in epibiosis, with a high percentage of covering (one-third of the surface). Out of the 37 epibiontic species recorded, the most recurrent described an ecological succession dominated by hydrozoans, sponges, bryozoans, serpulids and the parasitic soft coral Alcyomiun coralloides. Nevertheless, single colonies studied through time revealed the unpredictability of the colonization process. The peculiar habitat of a high naturalistic value of the granitic outcrops hosting the P. clavata forests demonstrates a widespread suffering condition, supported both by environmental and anthropogenic sources of stress. Such considerations make it necessary to review the current zonation of the area, where the actual vulnerability and usability evaluations are based on obsolete information.

Current and dynamic developments in green technologies have led to several innovation practices in the manufacturing sector only to become the top approaches used for achieving and accelerating sustainable development (SD) in the current business markets. In addition, manufacturing firms is in need of green innovation to be able to monitor and control their operations and enhance their environmental performance. However, regardless of its many benefits, the level of green innovation adoption and implementation is still lower than expected among manufacturing industries. Thus, this study aimed to minimize the gap by developing and validating a study model underpinned by Resource based view and Institutional theories, along with the Technology-Organization-Environment (TOE) framework in combination to convince firms to adopt green innovation. The study gathered data from 179 respondents using a survey distributed to manufacturing firms, after which data was exposed to Structural Equation Modeling (PLS-SEM) approach, for analysis. Based on the approach deliverables, all the integrated constructs of the model, namely perceived benefits, top management support, coercive pressure, normative pressure and mimetic pressure all predicted green management accounting practices. Moreover, green management accounting practices were found to directly and significantly affect green environmental performance. The developed integrated model provides a clear implication to decision-makers, indicating the importance of adopting and using green practices and innovative technologies for enhancing environmental performance. Based on the results from the reviewed advanced green technologies studies, there is considerable connection between green management accounting practices and environmental performance in the context of developing economies.

Evapotranspiration (ET) is an essential part of energy flow between the surface of the earth and the atmosphere, simultaneously involving the water, carbon, and energy cycles. It is mainly determined by climate change, land use, and land cover changes. Climate change is expected to intensify the hydrological cycle and alter ET. Land use affects ET within regional ecosystems mainly through vegetation changes and agricultural activities such as farmland reclamation, crop cultivation, and agricultural management. However, there is still a need for quantitative characterization of the impacts of climate change and human activities on ET and regional water resource efficiency in arid and semiarid regions. Based on Landsat-8 remote sensing imagery and land use data, the planting structure in the Liangzhou District of the middle reaches of the Shiyang River Basin was identified using a multiband and multitemporal approach in this study. Subsequently, the ET of major cash crops was inverted using the three-temperature model. This research quantitatively describes the responses of wheat and corn to the climate and human activities over a two-year period. Furthermore, the impact of planting structure and climatic factors on ET was elucidated. The results indicate that a combination of multitemporal green and shortwave infrared 1 bands is the optimal spectral combination to extract the planting structure. Compared to 2019, the wheat area decreased by 23.27% in 2020, while the corn area increased by 5.96%. Both crops exhibited significant spatial heterogeneity in ET during the growing season. The typical daily range of ET for wheat was 0.4–7.2 mm/day, and for corn, it was 1.5–4.0 mm/day. Among the climatic factors, temperature showed the highest correlation with ET (R = 0.80, p ≤ 0.05). Our research findings provide valuable insights for the fine identification of planting structures and a better understanding of the response of ET to climatic factors and human activities.

Fractures are present in hydrocarbon reservoirs of different porosity ranges. Seismic anisotropy has been widely used in fracture characterization and shown to be sensitive to background matrix porosities in theoretical studies. An understanding of the effects of background porosity on seismic anisotropy could improve seismic characterization in different fractured reservoirs. Based on synthetic rocks with controlled fractures, we conducted laboratory experiments to investigate the influence background porosity has on P wave anisotropy and shear wave splitting. A set of rocks containing the same fracture density (0.06) with varying porosities of 15.3%, 22.1%, and 30.8% were constructed. P and S wave velocities were measured at 0.5 MHz as rocks were water saturated. Results show that when porosity increased from 15.3% to 22.1%, P wave anisotropy and shear wave splitting exhibit slight fluctuations. However, when porosity continued to increase to 30.8%, P wave anisotropy declined sharply while shear wave splitting stayed nearly constant. The measured results were compared with predictions from equivalent medium theories. Qualitative agreements were found between theoretical predictions and measured results. In Eshelby-Cheng model, the increase of porosity reduces the fracture-induced perturbation in the fracture normal direction, resulting in a lower P wave anisotropy. In Gurevich(2003) model, the increase of porosity can reduce the compressional stiffness in parallel direction to a larger extent than that in perpendicular direction, thus leading to lower P wave anisotropy.

Accurate seasonal weather forecasts are vital across a broad spectrum of applications, bearing significant environmental and socioeconomic implications. This importance renders the subject a matter of primary interest to a wide range of stakeholders, including the general public, agricultural sector, emergency responders, financial institutions, and policy strategists. The need for precision in long-term predictive models necessitates the development of innovative methodologies. These methodologies should be capable of deciphering atmospheric patterns and mechanisms with detail, especially at a local level, without the resource constraints that dynamical downscaling imposes. In response to this expanding demand, this study presents a novel solution, combining a stochastic deep learning methodology, specifically Generative Adversarial Networks (GANs), with a Digital Elevation Model (DEM). The cornerstone of the proposed model is the enhancement of gridded temperature fields from seasonal forecasts. The area of focus was the Hellenic region, wherein the spatial resolution is amplified from a coarse 1° x 1° grid to an impressively detailed 0.1° x 0.1° grid. This offers a transformative perspective for interpreting and employing this crucial meteorological data. The results suggest that the downscaled fields adequately approximate the actual spatial distribution, although the predicted values tend to slightly overestimate and in some cases underestimate the original ones. This study underlines the potential of this approach to significantly enhance the resolution and utility of weather forecasts, thereby contributing to a variety of sectors dependent on reliable meteorological data.

This study reports fractal analysis of one-year radon in groundwater disturbances from five stations in China amid the catastrophic Wenchuan (Mw=7.9) earthquake of May 12, 2008 (day 133). Five techniques are used (DFA, fractal dimensions with Higuchi, Katz, Sevcik methods, power-law analysis) in segmented portions glided throughout each signal. Noteworthy fractal areas are outlined in the KDS, GS, MSS station data, while the portions were non-significant for PZHS and SPS. Up to day 133 critical epoch DFA-exponents have 1.5<=a<2.0 with several above 1.8. Fractal dimensions exhibit Katz’s D around 1.0-1.2, Higuchi’s D between 1.5-2.0 and Sevcik’s D between 1.0-1.5. Several power-law exponents are above 1.7 and numerous above 2.0. All fractal results of KDS-GS-MSS stations are further analysed using a novel computerised methodology which locates the exact out-of-threshold fractal areas and combines the outcomes of different methods per five, four, three, and two (maximum 13 combinations) versus nineteen Mw<=5.5 earthquakes of the area. Most different-technique coincidences are before the great Wenchuan earthquake and its post-earthquakes. This is not only with one method, but with 13 different methods. Other interpretations are also discussed.

Based on the daily observation data of 2254 meteorological stations in China from 1961 to 2021 after homogenization and correction, the extreme value analysis method that combines relative threshold and absolute threshold was used to identify extreme climate events in the mainland of China, namely extreme high temperature, extreme low temperature, extreme drought, extreme precipitation and extreme typhoon events. The frequency and linear variation trends of individual extreme events in the past 60 years were investigated. On this basis, the multi extreme events composite risk grade index (MXCI) was constructed, which can objectively reflect the comprehensive characteristics of multi extreme climate events in different regions. The results show that the high value areas of MXCI were mainly located in Southeast China and Southwest China. The MXCI presented a decreasing trend in most of the western and southeastern regions of China, while an increasing trend from Southwest China to the south of Northeast China, due to the frequent occurrence of extreme high temperature, extreme drought and other extreme events in these regions.

Rationale: The possible effect of Particulate Matter (PM10 and PM2.5 of diameter 10 and 2.5 µm respectively) levels on Covid-19 mortality is now well established. However, time-evolution of Covid-19 mortality according to PM2.5 levels has been scarcely investigated. Aim: To understand this relationship at the European level for the period 2020 (beginning) - 2022 (end). Methods: 16 representative locations in Europe (81 million people) with heterogeneous levels of PM2.5 (µg.m-3), from low to high. PM2.5 levels were assessed by various methods, and Covid-19 mortality was reported by Johns Hopkins University. Results: The trend of Covid-19 mortality vs. PM2.5 levels varied among locations. Overall, the estimated mean value was of a 40±20% mortality increase per 1 µg.m-3 PM2.5 increase. The stronger the positive gradient of the PM peak, the stronger the positive gradient of the Covid-19 mortality. Exposure to several PM peaks during about a 2-month period was the main contributor to Covid-19 mortality increases. Conclusion: Our data confirm a temporal relation between PM2.5 exposure and Covid-19 mortality, considering a 2-month integration-time for pollution events. Number-concentrations of PM should be used in the future rather than the PM2.5 mass-concentrations (µg.m-3) with the consideration of PM composition to better explain this finding.

Crop residue burning produces a lot of polluting gases and fine particles, endangering human health, damaging soil structure, and causing fire accidents. In addition to the impact of residue burning on the local environment, pollutants can spread with the wind to more distant areas and impact the air quality of surrounding areas, especially cities. Nevertheless, a comparative analysis of the impact of two common residue burning parameters, the number of residue fire points and residue burned area, on urban air quality indicators has not been reported. In this study, the correlation between these two different residue burning parameters on air quality in Daqing City was investigated comparatively using the Visible Infrared Imaging Radiometer Suite (VIIRS) fire point product, the Moderate-resolution Imaging Spectroradiometer (MODIS) burned area product, and buffer zone analysis. The association between MODIS burned area products and air quality index (AQI) was found to be around 0.8, with a maximum of 0.816 at a buffer zone radius of 50 km. Meanwhile, it was found that the correlation between the number of residue fire points extracted from the VIIRS active fire products and air quality was above 0.6, again with a maximum of 0.745 at a buffer radius of 50 km. Within other levels of buffer zones, the correlation between residue burned area and AQI was consistently higher than that between residue fire points and AQI. By comparing the correlation between VIIRS fire points, MODIS burned area, and AQI with the concentration of each pollutant, we found that the correlation between residue burned area and AQI and the concentration of each pollutant is higher. MODIS burned area monitoring, on the other hand, detects changes in the time series of images taken by satellite at two transit moments to obtain the new burned area and cumulative burned area during this period, allowing the monitoring of fire traces caused by fire points at non-transit moments. From analyzing the correlation between residue fire points, residue burned area, and the concentration of each pollutant (PM2.5, PM10, CO, NO2, SO2, O3), we found significant correlations between residue burning and PM2.5, PM10, CO, and NO2 concentrations, with the highest correlation (R2) of 0.81 for PM2.5. Moreover, the correlation between residue burned area and PM2.5, PM10, CO, and NO2 concentrations was significantly higher than that between the number of residue fire points and their concentrations.

Based on multi-source remote sensing data, scenario analysis, and model simulation, the Pareto optimal solutions for water supply, water purification (N retention), and carbon storage and sequestration services under different scenarios were sought by adjusting its land use structure. The results showed that. In Scenario 1(S1), the water supply service needs to increase by 86.820 to 11.211 billion cubic metres, the water purification (N retention) service needs to decrease by 11,400 to 11,700 tons, and the carbon storage and sequestration service need to decrease by 2.070 to 2.487 billion tons. In Scenario 2(S2), the water supply service needs to increase by 8.243–10.666 billion cubic metres, the water purification (N retention) service needs to decrease by 11,300–1.10 million tons, and the carbon storage and sequestration service needs to decrease by 2.033 to 2.466 billion tons. In Scenario 3 (S3), the water supply service needs to increase by 7.832–11.437 billion cubic metres, the water purification (N retention) service needs to decrease by 1.16–10,800 tons, and the carbon storage and sequestration service needs to decrease by 19.220 to 2.380 billion tons. After land use optimisation and adjustment, the S3 ecological land structure is complete and consistent with the vision of ecological protection and urban development in the study area, which is the optimal scenario. After optimising the S3 ecosystem service supply pattern, the water supply, water purification (N retention), and carbon storage and sequestration services could connect the western and eastern ecosystem service supply areas, balance the overall ecosystem service supply pattern of the study area and meet the demand for ecosystem services. The results can guide regional land planning and ecosystem service management optimisation.

This study examines the activities conducted at the archaeological site of Aptera in Crete, Greece. The research was part of the DIACHRONIC LANDSCAPES International Design Workshop, organized by the CAM (Center for Mediterranean Architecture), TUC (Technological University of Crete School of Architecture), and UNIFE (University of Ferrara Department of Architecture). This article outlines the methods used for data acquisition and processing on a territorial scale, which generated digital outputs necessary for the analysis and design phases of the workshop, as well as for further examination of the results. The collected data, obtained through low-cost aerial photogrammetric surveying and GNSS terrestrial coordinate detection, were integrated in a Structure from Motion workflow that led to the creation and exportation of various digital outputs, such as point clouds, DTM, DSM, orthophotos, and contour lines. An accuracy analysis was performed to evaluate the effectiveness and efficiency of the digital models compared to the implemented surveying strategies, including the Ground Control Point and Quality Check Point marker positioning strategy. The resulting digital models proved to be valuable assets for analysis and design within the workshop and provided insightful prospects for future research and territorial-scale projects.

Land Surface Temperature (LST) is significant for climatological and environmental studies. LST products from satellites, however, suffer from the tradeoff between spatial and temporal resolution. Spatial downscaling has emerged as a well explored field aiming to overcome limitations arising from this tradeoff. Previous research on regression based LST downscaling models focused on utilizing predictors derived from optical imagery. Weather-dependency of optical imagery data, however, can influence downscaling models by the weather conditions. To cope this issue, in this study, we involve predictors derived from the weather-independent Sentinel-1 Synthetic Aperture Radar (SAR) imagery to downscale Landsat-8 LST data. In this context, we propose to use machine learning techniques, namely Random Forest (RF) and Convolutional Neural Networks (CNN). To demonstrate the applicability and performance of the proposed method, extensive experimental analyses were conducted over Zuid-Holland in the Netherlands. From the experiments, we found that the results obtained with radar predictors were comparable to those achieved using optical predictors. This confirms that the proposed method indeed paves a new way for mapping land surface temperature using SAR images.

Disinfection byproducts (DBPs) are formed whenever disinfectant ingredients are in contact with organic matter. Due to widespread increase in production and use of disinfectants and antiseptics, the presence of their components in coastal environments is increasing. However, very limited scientific literature is available in regard to the occurrence of DBPs and related compounds in the coastal zone and particularly in seawater. In this context, the aim of this preliminary compilation is to outline the main up-to-date findings and raise awareness on their increasing occurrence in coastal environments. Sampling and analysis of marine samples in the USA, Spain, China, Taiwan, Malaysia, Korea, Kuwait and Hong-Kong revealed the presence of several categories of DBPs and related compounds in coastal environments, with the highest levels being detected in urban areas, probably related to the nearby wastewater treatment plants. The investigations considered in this preliminary compilation, report the detection of DBPs and related compounds as well as the formation of toxic brominated and iodinated DBPs in high levels due to chlorination of wastewater, especially after use of seawater for flushing in toilets. New DBP groups have also been detected, namely halogenated phenolic DBPs and halopyrroles.

This essay review explores the concept of climate-smart forestry as an approach to mitigating and adapting to climate change. It highlights the need for a holistic approach to forestry that considers regional differences and synergies between ecosystem services. The essay discusses various management strategies at different scales, including species selection, mixed species cultivation, and the promotion of the bioeconomy. It also examines the trade-offs and synergies between different forest uses and the effects of forest management on ecosystem services. Furthermore, the review addresses major abiotic and biotic damage risks to forests, such as wildfires, windstorms, and bark beetle attacks, and proposes risk management strategies. Lastly, the review delves into the management of peatland forests, discussing the role of drainage, the impact of ditch network maintenance, and the challenges of peat ash fertilization. Overall, the review provides valuable insights into climate-smart forestry and its potential to contribute to climate change mitigation and adaptation.