Transition delaying is of great importance for the drag and heat flux reduction of hypersonic flight vehicles. The first mode within low frequency and the second mode within high frequency exist simultaneously during the transition of hypersonic boundary layer. This paper proposes a novel bi-frequency synthetic jet to suppress low- and high-frequency disturbances at the same time. Orthogonal table and variance analysis are used to compare the control effects of jet with different frequencies, amplitudes and positions. Linear stability analysis results show that, low frequency synthetic jet can suppress the first mode when it is arranged upstream of synchronization point, while the second mode control effect is relatively weak. The higher the high frequency is, the stronger the suppression effect is on the first mode. For the second mode, the suppression effect is only at f2=89.09kHz. The larger the amplitude, the weaker the promoting effect for the first mode and the second mode, and the more obvious the suppressing effect. For the cases with synthetic jet downstream of synchronization point, all levels of the three parameters promote the unstable mode. In terms of the growth rate with the spanwise wave number, the control effect of the same factor and level under different spanwise wave number is different. In order to obtain the optimal control effect on transition, the three factors and the arrangement position of the synthetic jet should be selected as follows: the position is arranged in the upstream, with f1 = 17.82kHz, f2 = 89.9kHz, a =0.007, so that the maximum growth rate of the first mode is reduced by 9.06% and that of the second mode is reduced by 1.28% compared with the uncontrolled state.

Feruloylacetone (FER) is a natural degradant of curcumin after heating, which structurally reserves some functional groups of curcumin. It is not as widely discussed as its original counterpart in previous studies and, therefore, its anti-cancer efficacy is investigated herein. This study focuses on the suppressive effect of FER on colon cancer, as the efficacious effect of curcumin on this typical cancer type has been well evidenced. In addition, demethoxy-feruloylacetone (DFER) was applied to compare the effect that might be brought on by the structural differences of the methoxy group. It was revealed that both FER and DFER inhibited the proliferation of HCT116 cells, possibly via suppression of the phosphorylated mTOR/STAT3 pathway. Notably, FER could significantly repress both the STAT3 phosphorylation and protein levels. Furthermore, both samples showed the capability of arresting HCT116 cells at the G2/M phase via the activation of p53/p21 and upregulation of cyclin-B. In addition, ROS elevation and changes in mitochondrial membrane potential were revealed, as indicated by p-atm elevation. The apoptotic rate rised to 36.9% and 32.2% after being treated by FER and DFER, respectively. In summary, both compounds exhibited an anti-cancer effect, and FER showed a greater pro-apoptotic effect, possibly due to the presence of the methoxy group on the aromatic ring.

Malaria, as a major global health problem, continues to affect a large number of people each year, especially those in the developing countries. Effective drug discovery is still one of the main efforts to control malaria. As natural products are still considered as a key source for discovery and development of therapeutic agents, we have evaluated more than 2000 plant extracts against Plasmodium falciparum. As a result, we discovered dozens of plant leads that displayed antimalarial activity. Our phytochemical study of some of these plant extracts led to identification of several potent antimalarial compounds. The prior comprehensive review article entitled “Antimalarial activity of plant metabolites” by Schwikkard and Van Heerden (2002) reported structures of plant-derived compounds with antiplasmodial activity and covered literature up to the year 2000. As a continuation of this effort, the present review covers the antimalarial compounds isolated from plants, including marine plants, reported in the literatures from 2001 to the end of 2017. During the span of the last 17 years, 175 antiplasmodial compounds were discovered from plants. These active compounds are organized in our review article according to their plant families. In addition, we also include ethnobotanical information of the antimalarial plants discussed.

Remote sensing image registration plays an important role in military and civilian fields, such as natural disaster damage assessment, military damage assessment and ground targets identification, etc. However, due to the ground relief variations and imaging viewpoint changes, non-rigid geometric distortion occurs between remote sensing images with different viewpoint, which further increases the difficulty of remote sensing image registration. To address the problem, we propose a multi-viewpoint remote sensing image registration method which contains the following contributions. (i) A multiple features based finite mixture model is constructed for dealing with different types of image features. (ii) Three features are combined and substituted into the mixture model to form a feature complementation, i.e., the Euclidean distance and shape context are used to measure the similarity of geometric structure, and the SIFT (scale-invariant feature transform) distance which is endowed with the intensity information is used to measure the scale space extrema. (iii) To prevent the ill-posed problem, a geometric constraint term is introduced into the L2E-based energy function for better behaving the non-rigid transformation. We evaluated the performances of the proposed method by three series of remote sensing images obtained from the unmanned aerial vehicle (UAV) and Google Earth, and compared with five state-of-the-art methods where our method shows the best alignments in most cases.

The variation of mutual inductance and load parameters will affect the transmission power and efficiency of the inductive power transfer (IPT) system. The identification of mutual inductance and load parameters is an essential part of establishing a stable and reliable IPT system. This paper presents a joint identification method of load and mutual inductance for LCC-S IPT system, which does not require the establishment of primary and secondary communication and related control. Firstly, the resistance-inductance characteristics of the equivalent load of the rectifier are analyzed by simulation, and then the rectifier and system load are equivalent to the circuit model of resistance and inductance in series. Secondly, the characteristics of the reflected impedance are analyzed, and the functional relationship between the transmitter impedance and the rectifier impedance is established by using the ratio of the real part to the imaginary part of the reflected impedance, which realizes the decoupling of the load and the mutual inductance. Thirdly, the functional relationship between the equivalent impedance of the rectifier and the load resistance of the system is obtained by data fitting. Then, the equations of the above two functional relationships are combined. By measuring the voltage of the parallel compensation capacitor at the transmitting side, the current of the transmitting coil and the phase difference between the two, the battery load can be solved first, and then the mutual inductance can be calculated, so that the high-precision identification of the load and mutual inductance can be realized. Finally, an experimental platform of LCC-S IPT system is built for experimental verification. The experimental results show that the maximum identification errors of mutual inductance and load are 5.20 % and 5.53 %, respectively, which proves that the proposed identification method can achieve high precision identification.

Semiconductor materials have been shown to have better photocatalytic behavior and can be utilized for the photodegradation of organic pollutants. In this work, three-dimensional flower-like SnS₂ were synthesized by a facile hydrothermal method. Core-shell structured SiO₂@α-Fe₂O₃ nanocomposites were then deposited on the top of the SnS₂ flowers. The as-synthesized nanocomposites were characterized by X-ray diffraction (XRD), Raman spectroscopy, field emission scanning electron microscopy (FE-SEM), Brunauer-Emmett-Teller (BET) and photoluminescence spectroscopy (PL). The photocatalytic behavior of the SnS₂-SiO₂@α-Fe₂O₃ nanocomposites was observed by observing the degradation of methylene blue (MB). The results show an effective enhancement of photocatalytic activity for the degradation of MB especially for the 15 wt. % SiO₂@α-Fe₂O₃ nanocomposites on SnS₂ flowers.

This paper proposes two fully-automatic machine-extracted linguistic features from an unlimited text input for Mandarin prosody generation. One is the punctuation confidence (PC) which measures the likelihood of inserting a major punctuation mark (PM) at a word boundary. Another is the quotation confidence (QC) which measures the likelihood of a word string to be quoted as a meaningful or emphasized unit in text. Because a major PM in a text is highly correlated with a prosodic break, and a quoted word string plays an important role in human language understanding, the two features potentially could provide useful information for prosody generation. The idea is first realized by employing conditional random field (CRF)-based models to predict major PMs, quoted word string locations, and their associated confidences, i.e., the PC and the QC, for each word boundary. Then, the predicted punctuations and their confidences are combined with traditional contextual linguistic features to predict prosodic-acoustic features. Both objective and subjective tests showed that the prosody generation with the proposed linguistic features performed better than the one without the proposed features. So, the proposed PC and QC are promising features for Mandarin prosody generation.

The 1060 aluminium alloy is widely applied to electronic industry, construction area, aerospace field, traffic engineering, decoration and consumption goods market for its good chemical, physical and mechanical properties. In general, excellent processing property is necessary and important for manufacturing of complicated panels. In this paper, a special 2D ultrasonic vibration incremental forming method is designed to improve its plasticity and mechanical properties. Three kind of processing methods including traditional single point incremental forming, longitudinal ultrasonic vibration incremental forming and 2D ultrasonic vibration incremental forming are conducted for flexible manufacture of conical parts of 1060 aluminium alloy sheet. Then micro-hardness tests, residual stress tests and scanning electron microscopy tests are carried out to probe its revolution of micro-structure and mechanical properties and to analysis the effects of different types of ultrasonic vibration on plasticity and fracture characteristic of 1060 aluminium alloy. It is proved that 2D ultrasonic vibration is facilitated to improvement of plasticity and surface qualities of 1060 aluminium alloy than the other two processing methods. So, the novel 2D ultrasonic vibration incremental forming possesses substantial application values on flexible and rapid manufacturing of complicated thin-walled component of aluminium alloy.

This paper proposes an interpretable geometry solution based on the formal language set of text and diagram. Geometry problems are solved by machines, which still poses challenges in natural language processing and computer vision. Significant progress promotes existing methods in the extraction of geometric formal languages. However, the neglect of the graph structure information in the formal language and the lack of further refinement of the extracted language set can lead to the poor effect of the theorem prediction and affect the accuracy in problem solving. In this paper, the formal language graph is constructed by the extracted formal language set and used to theorem prediction by graph convolutional network. So as to better extract the relationship set of diagram elements, an improved diagram parser was proposed. The test results indicate that the improved method has good results in solving the problem with interpretability geometry.

Speaker recognition methods based on convolutional neural networks (CNN) have been widely used in the security field and smart wearable devices. However, the traditional CNN has a large number of hyperparameters that are difficult to be determined, which makes the model easy to fall into local optimum or even fail to converge during the training process. Intelligent algorithms such as particle swarm optimization and genetic algorithm are used to solve the above problems. However, these algorithms have poor performance compared with the current emerging meta-heuristic algorithms. In this study, the dung beetle optimized convolution neural network (DBO-CNN) is proposed to identify the speakers, which is helpful in finding suitable hyperparameters for training. By testing the dataset of 50 people, it was demonstrated that the accuracy of the model was significantly improved by using this approach. Compared with the traditional CNN and CNN optimized by other intelligent algorithms, the accuracy of DBO-CNN has increased by 0.6%~4.8%, and reached 98.3%.

Ultrasonic-guided lamb wave approach is an effective non-destructive testing (NDT) method used for detecting localized mechanical damage, corrosion, and welding defects experienced in metallic pipelines. Signal processing of the guided waves is often challenged due to the complexity of operational conditions and environments in the pipelines. Machine learning approaches in recent years, including convolutional neural networks (CNN) and long short-term memory (LSTM), have exhibited their advantages to overcome these challenges for signal process and data classification of complex systems, thus great potential for damage detection of critical oil/gas pipeline structures. In this study, a CNN-LSTM hybrid model is utilized for decoding ultrasonic guided waves for damage detection of metallic pipelines, and twenty-nine features are extracted as input to classify different types of defects from metallic pipes. The prediction capacity of the CNN-LSTM model is assessed by comparing it to the CNN and LSTM. The results demonstrate that the CNN-LSTM hybrid model exhibits much higher accuracy, with 94.8%, as compared to those of CNN and LSTM. Interestingly, the results also reveal that predetermined features, including time-, frequency-, and time-frequency domains, could significantly improve the robustness of the deep learning approaches, even though the deep learning approaches are often believed they include automated feature extraction, without the hand-crafted steps as the shallow learning do. Furthermore, the CNN-LSTM model displays higher performance when the noise level is relatively low (e.g., SNR=9 or higher), as compared to the other two models, but its prediction drops gradually with the increase of the noise.

Metal-organic frameworks (MOFs), composed of metal nodes and inorganic linkers are promising for a wide range of applications due to their unique periodic frameworks that can be flexibly tuned. Understanding of the structure-activity relationships can facilitate the development and application of MOFs nanomaterials. Transmission electron microscopy (TEM) is a one-of-a-kind technique capable of characterizing MOFs microstructures at the atomic scale. Besides, in-situ TEM set-ups make it possible to direct visualize the microstructural evolution of MOFs in real time, which enables monitoring transitions of MOFs during growth as well as under working conditions. However, MOFs are so sensitive to the high-energy electron beam which makes TEM-based characterizing methods challenging. In this review, we first introduce the main damage mechanisms for MOFs under electron beam irradiation and two strategies to minimize the damages: low-dose TEM and cryo-TEM. Then, we discuss the techniques combined with the two strategies to analyze the MOFs’ microstructure, including three-dimensional electron diffraction, direct detection electron counting camera, and iDPC-STEM. Groundbreaking milestones and research advances with respect to static characterization of MOFs structures are highlighted. In-situ TEM studies are exemplary reviewed to provide insights into MOFs dynamics induced by various stimuli. Additionally, perspectives on promising techniques that may further facilitate the MOFs study using TEM are analyzed.

In order to properly cover different scenarios, radiation patterns of antennas should be accordingly adjusted before fabrication. However, most antennas are unable to provide both broadside beam and designable conical beam which are usually-used radiation patterns for radio coverage. In this paper, a planar Circular Polarized (CP) annular Leaky-Wave Antenna (LWA) with conical beam is proposed, which is realized on annular Substrate-Integrated Waveguide (SIW). Broadside beam or conical beam could be easily obtained by fabricating the LWA with modified structural parameters. The central operating band is 5.8 GHz. The LWA allows only the -1th spatial harmonic to radiate, while the fundamental wave and other spatial harmonics are suppressed in slow wave mode. In order to validate the design effectiveness, two examples for broadside beam and conical beam radiation are fabricated and measured. The measurement results show good agreement with the simulation results. The proposed LWA presents a promising radiation performance and is a good candidate for wireless communication applications.

Fiber aggregation in nanocomposites has an important effect on the macroscopic electrical performance. To quantitatively evaluate its effect, an index to characterize the degree of aggregation is imperative, and ideally it should have three features simultaneously, i.e., single-parametric, dimensionless and physically meaningful, applicable to different aggregation topologies, and one-to-one corresponding to material electrical properties. To this end, a new aggregation degree is proposed, which is defined as the average increased number of fibers that connect with each one when fibers aggregate from a uniformly distributed state. This index is applicable to different aggregation topologies from lump-like aggregating clusters to network-like aggregating clusters. This index is proven to only depend on the local features of aggregating clusters, and can be concisely expressed by the characteristic parameters of local structure, via geometric probability analysis and numerical validations. Further, a one-to-one linear relation between the aggregation degree and percolation threshold is established by Monte Carlo simulations, which is independent of the distribution law of the fibers. This work provides a guide to the property characterization, performance prediction and material design of nanocomposites, and also gives a physical insight into the understanding of systems with similar non-uniform distributions.

Maritime ship monitoring plays an important role in maritime transportation. Fast and accurate detection of maritime ship is the key to maritime ship monitoring. The main sources of marine ship images are optical images and synthetic aperture radar (SAR) images. Different from natural images, SAR images are independent to daylight and weather conditions. Traditional ship detection methods of SAR images mainly depend on the statistical distribution of sea clutter, which leads to poor robustness. As a deep learning detector, RetinaNet can break this obstacle, and the problem of imbalance on feature level and objective level can be further solved by combining with Libra R-CNN algorithm. In this paper, we modify the feature fusion part of Libra RetinaNet by adding a bottom-up path augmentation structure to better preserve the low-level feature information, and we expand the dataset through style transfer. We evaluate our method on the publicly available SAR dataset of ship detection with complex backgrounds. The experimental results show that the improved Libra RetinaNet can effectively detect multi-scale ships through expansion of the dataset, with an average accuracy of 97.38%.

Plants grown under fluctuating light impact plant developments compared with those grown under non-fluctuating light conditions. However, our knowledge on the underlying regulatory mechanisms is still quite limited, particularly from the transcriptional perspective. In order to investigate the influence of different light intensity distributions on tomato plant development, we designed three fluctuating light intensity distributions with the non-fluctuating light intensity as control and compared the transcriptional differences after five weeks of treatment. We found plant height and aerial/root weight were significantly reduced under all fluctuating light treatments. Transcriptome analysis revealed that the number of up and down regulated genes had a distinct distribution pattern between different treatments and control. The largest difference between the numbers of down and up regulated genes was found between treatment 1 and 3, reaching to a total of 416 genes. The number and type of the top 20 enriched pathways differed between treatments and control. The largest number of genes enriched was involved in the biosynthesis of secondary metabolites. These results provide insights into the transcriptional regulations of tomato under different light intensity distributions.

A phenomenological constitutive model is developed to describe the uniaxial transformation ratcheting behaviors of super–elastic shape memory alloy (SMA) by employing a cosine–type phase transformation equation with the initial martensite evolution coefficient that can capture the feature of the predictive residual martensite accumulation evolution and the nonlinear hysteresis loop on a finite element (FE) analysis framework. The effect of the applied loading level on transformation ratcheting are considered in the proposed model. The evolutions of transformation ratcheting and transformation stresses are constructed as the function of the accumulated residual martensite volume fraction. The FE implementation of the proposed model is carried out for the numerical analysis of transformation ratcheting of the SMA bar element. The integration algorithm and the expression of consistent tangent modulus are deduced in a new form for the forward and reverse transformation. The numerical results are compared with those of existing model and the experimental results to show the validity of the proposed model and its FE implementation in transformation ratcheting. Finally, a FE modeling is established for a repeated preload analysis of SMA bolted joint

This paper investigates a distributed, coordinated motion control network based on multiple direct-drive, linear switched reluctance machines (LSRMs). A hierarchical, two-level synchronization control strategy is proposed for the four LSRMs based motion control network. The high-level, reference signals agreement algorithm is first employed to correct the asynchronous behaviors of the position commands. Then, the low-level tracking synchronization method is applied for the collaborative position control of the four LSRMs. The proposed two-level, fault-tolerant control strategy eliminates the asynchrony of the reference signals and it also guarantees the coordinated tracking control performance of the four LSRMs. Experimental results demonstrate that effective coordinated tracking control can be ensured, based on successful agreement of reference signals and an absolute tracking error falling within 2 mm can be achieved.

Multi-channel and multi-parameter near-infrared spectrometers (NIRS) have gradually become a new research direction and hot spot due to their ability to provide real-time, continuous, comprehensive indicators of multiple parameters. However, multi-channel and multi-parameter detection may lead to crosstalk between signals. There is still a lack of benchmarks on the evaluation of reliability, sensitivity, stability and response consistency of the NIRS instrument. In this study, a set of test methods (the ink drop test, multi-channel crosstalk test and multi-parameter crosstalk test) for analysis crosstalk and verifying the reliability of NIRS were conducted to test experimental verification on a multi-channel (8-channel), multi-parameter (4-parameter) NIRS instrument independently developed by our team. Results show that these tests can be used to analyze the signal crosstalk and verify the reliability, sensitivity, stability and response consistency in the NIRS instrument. This study contributes to the establishment of benchmarks for the NIRS instrument crosstalk and reliability testing. These novel tests have the potential to become the benchmark for the NIRS instrument reliability testing.

The biosynthesis of C27-29 sterols from their C30 precursor squalene involves C24-alkylation and removal of three methyl groups, including two at the C4 position. The two C4 demethylation reactions require a bifunctional enzyme known as 3β-hydroxysteroid dehydrogenase/C4-decarboxylase (3βHSD/D) that removes an oxidized methyl (carboxylic) group at C4 while simultaneously catalyzing the 3β-hydroxyl3-keto oxidation. Its loss-of-function mutations cause ergosterol-dependent growth in yeast and congenital hemidysplasia with ichthyosiform erythroderma and limb defect (CHILD) syndrome in humans. Although plant 3βHSD/D enzymes were well studied enzymatically, their developmental functions remain unknown. Here we employed a CRISPR/Cas9-based genome-editing approach to generate knockout mutants for two Arabidopsis 3βHSD/D genes, HSD1 and HSD2, and discovered the male gametophytic lethality for the hsd1 hsd2 double mutation. Pollen-specific expression of HSD2 in the heterozygous hsd1 hsd2/+ mutant not only rescued the pollen lethality but also revealed critical roles of the two HSD genes in embryogenesis. Our study thus demonstrated essential functions of the two Arabidopsis 3βHSD/D genes in male gametogenesis and embryogenesis.

In view of the floating rectangular aerostatic guideway problem of low load capacity and stiffness, this paper puts forward a kind of closed rectangular aerostatic guideway and its optimized design. Firstly, the analytic calculation formula of a closed rectangular aerostatic guideway was deduced. The use of MATLAB software for the numerical simulation and the parameter influence analyses was carried out in terms of the gas supply pressure on load capacity and stiffness. A simulation model of the rectangular air bearing was also built using the Fluent software, and the model was used for simulation calculations. Secondly, the static performance of the rectangular air bearing was analyzed by analyzing the distribution position and number of orifices on its load capacity and stiffness. On this basis, the response surface optimization design method is used to analyze the variation law of the load capacity and stiffness of the air bearing under different restrictor structural parameters. Finally, the optimal design parameters for the rectangular air bearing are obtained. The simulation results show that the optimized rectangular air bearing designed in this paper has a good load capacity and stiffness of 644.58N and 63.405N N∙μm^(-1).

Taste determination in small molecules is critical in food chemistry, but traditional experimental methods can be time-consuming. Consequently, computational techniques have emerged as val-uable tools for this task. In this study, we explore taste prediction using various molecular feature representations and assess the performance of different machine learning algorithms on a dataset comprising 2,601 molecules. The results reveal that GNN-based models outperform other ap-proaches in taste prediction. Moreover, consensus models that combine diverse molecular repre-sentations demonstrate improved performance. Among these, molecular fingerprints + GNN con-sensus model emerges as the top performer, highlighting the complementary strengths of GNNs and molecular fingerprints. These findings have significant implications for food chemistry research and related fields. By leveraging these computational approaches, taste prediction can be expedited, leading to advancements in understanding the relationship between molecular structure and taste perception in various food components and related compounds.

Abstract: Interrupted-sampling repeater jamming (ISRJ) is a kind of intra-pulse coherent decep-tion jamming that can generate false target peaks in the range profile and interfere with the de-tection and tracking of real targets. In this paper, an anti-ISRJ method based on the intra-pulse orthogonal waveform is proposed, which can recognize common interference signals by com-paring sub-signal matched filtering results. For some special scenes where real targets cannot be directly differentiated from false targets, a new recognition method based on the energy discon-tinuity of the interference signal in the time domain is proposed in this paper. The method pro-posed in this paper can recognize real and false targets in all ISRJ modes without any prior in-formation, such as jammer parameters, with a small amount of calculation, which is suitable for actual radar systems. Simulation experiments using different interference parameters show that although this method has a 3dB loss of pulse compression gain, it can completely suppress dif-ferent kinds of ISRJ interference when the SNR before pulse compression is higher than -20dB, with 100 % target detection probability.

The central coast is one of the importantly livable regions in China, and green land plays a meaningful role in improving human settlements through regulating ecosystem services. However, the research on spatiotemporal heterogeneity of green land in different urbanized areas are still lacking in this region, which limits the timeliness of reporting on the land-surface thermal properties of residential environment from green land perspective. To address this issue, the synergistic methodology of “artificial numerical technology -- urban interior mixed pixel classification -- surface radiation energy balance model” was applied to investigate the green land change and its impact on human settlements in Rizhao region, which is known for its coastal ecology and greenery in China and obtained the United Nations habitat award. Main conclusions of this study are below: (1) Although total green land decreased by 474.05 km2, resulting in a decrease of 9.17% in its share of the entire study area from 2000-2022 during the urbanization process, but the greening levels improved within the built-up area, with the greening proportion of 25.34% in 2000 and 42.98 km2 in 2022. (2) Differences in green land at different urbanized regions were first observed, namely, urban greening rate was 37.78% in the old urban areas of 2022, while it was up to 46.43% in new urban areas. More attention was paid to the construction of urban green space during urban expansion, which will inevitably bring better visual and comfort experience to residents. (3) Thermal comfort indicators for urban residents were evaluated in latent heat flux (0-457.83 W/m2), sensible heat flux (0-645.09 W/m2), total available energy (254.07-659.42 W/m2) and others. (4) The lowered cooling temperature effect in the middle, high green land density region was 1.05 ℃ and 2.12 ℃ compared to the low-density region, and the average air temperature was 25.86 ℃. Also, spatial patterns of hot and cold uncomfortable areas were displayed in this study. Overall, this study provides the meaningfully practical reference for exploring the spatiotemporal heterogeneity of green land and its impact on residents' environments from the perspective of land-surface thermal properties in coastal areas of China and around the world.

Since the exploitation of mineral resources results in the release of radionuclides, and consuming radionuclides affects public health in the short and long term. A case study of the environmental radiation impact from coal mining and germanium processing was carried out in southwest China. The coal mines contain germanium and uranium and have been exploited for more than 40 years. The farmlands around the site of coal mining and germanium processing have been contaminated by the solid waste and mine water in some extend since then. Samples of crops have been collected from contaminated farmlands in research area. The research area covers a radius of 5 km, in which there are 2 coal mines located. 210Pb and 210Po have been analyzed as the key radionuclides during monitoring program. The average activity concentrations of 210Pb and 210Po in the crops were 1.38 and 1.32 Bq/kg in cereals, 4.07 and 2.19 Bq/kg in leafy vegetables and 1.63 and 1.32 Bq/kg in root vegetables. The annual effective doses due to the ingestion of 210Pb and 210Po in consumed crops have been estimated for adult residents living in research area. The average annual effective dose was 0.336mSv/a, while the minimum was 0.171 mSv/a and the maximum was 0.948 mSv/a. The results show that crops grown on contaminated farmland contained an enhanced level of radioactivity concentration. Ingestion doses of local residents in research area were significantly higher than the China average level of 0.112 mSv/a, and the world average level of 0.042 mSv/a through 210Pb and 210Po in crops intake respectively.

In Ethiopia, bamboo thickets and woodlands play an important role in soil-water conservation and climate change mitigation in arid and semi-arid regions. However, bamboo mass flower-ing, rapid demographic changes and expansion of agricultural investments to bamboo domi-nated areas have led to deforestation and land degradation. In this study, we determined the effects of deforestation and subsequent cultivation on soil physical and chemical properties along a chronosequence of closely located agricultural lands with different ages (1, 3, 5 and 7 years) since converted from natural lowland bamboo forest. Hence, soil samples (n = 90) have been taken from both natural bamboo forests and adjacent agricultural lands at two soil depths (0-20 cm and 20-40 cm). Our result showed that CEC, K+, Ca+, Mg+ and available P were varied significantly with respect to cultivation periods and soil depth, while soil pH and Na+ varied with soil depth (P < 0.001). Soil C and total N contents (g/kg) in 0-20 cm soil layer declined significantly and exponentially with increasing years under cultivation. Conversion of natural bamboo forest to cropland during the past seven-year period significantly increased soil pH with soil depths, while CEC was declined throughout the cultivation period and soil depth. In general, the result revealed that conversion of natural lowland bamboo and subsequent cultivation of soil had negative effects on measured soil physicochemical properties.

Open domain question answering (OpenQA) tasks have been recently attracting more and more attention from the natural language processing (NLP) community. In this work, we present the first free-form multiple-choice OpenQA dataset for solving medical problems, MedQA, collected from the professional medical board exams. It covers three languages: English, simplified Chinese, and traditional Chinese, and contains 12,723, 34,251, and 14,123 questions for the three languages, respectively. We implement both rule-based and popular neural methods by sequentially combining a document retriever and a machine comprehension model. Through experiments, we find that even the current best method can only achieve 36.7%, 42.0%, and 70.1% of test accuracy on the English, traditional Chinese, and simplified Chinese questions, respectively. We expect MedQA to present great challenges to existing OpenQA systems and hope that it can serve as a platform to promote much stronger OpenQA models from the NLP community in the future.

Upon the implementation of the European Union Carbon Border Adjustment Mechanism (CBAM), substantial challenges are anticipated to impact the international trade of Chinese steel products. To safeguard the competitiveness of Chinese steel products on the global stage, this paper establishes a tripartite evolutionary game model, involving large steel enterprises, small and medium-sized steel enterprises, and the government. The model integrates collaborative emission reduction and free-riding benefits among enterprises, along with the government's dynamic subsidies and penalties. The paper analyzes the evolutionary trends and stable states of the three parties during different stages of CBAM, including a sensitivity analysis of key parameters. The findings indicate that large enterprises demonstrate a heightened sensitivity to CBAM, while small and medium-sized enterprises are more significantly influenced by free-riding benefits. Government intervention should be strategically timed and incline towards passive management during the strengthening phase of CBAM. Additionally, the refinement of the Chinese carbon market emerges as an effective means to counter CBAM. This paper provides theoretical support for how steel enterprises and the government can respond to CBAM, aiding stakeholders in selecting optimal strategies during different implementation stages and mitigating the impacts of CBAM to the maximum extent possible.

8-oxoguanine glycosylase 1 (OGG1), which was initially identified as the enzyme that catalyzes the first step in the DNA base excision repair pathway, is now known also as a modulator of gene expression. What is important for cancer, is that OGG1 acts as a modulator of NFκB-driven gene expression. Specifically, oxidant stress in the cell transiently halts the enzymatic activity of substrate-bound OGG1. The stalled OGG1 facilitates DNA binding of transactivators, including NFκB, to their cognate sites to enable expression of cytokines and chemokines, with ensuing recruitment of inflammatory cells. Recently, we highlighted chief aspects of OGG1 involvement in regulation of gene expression, which have a significance in lung cancer development. However, OGG1 has also been implicated in the molecular underpinning of acute myeloid leukemia. In general, the capacity of cancer cells to adapt to oxidative stress depends on molecular systems such as the interface of OGG1 with NFκB, which bestows a cancer cell with the molecular mechanism of transformation of its microenvironment to enable adaptation and survival of malignant clones.

Effects of Lactobacillus plantarum (L. plantarum) strain P3 and mutant strain P3-M2 with antioxidant properties on fermented sausage flavour via lipid and protein oxidation inhibition were investigated. The commerical strain was used to as positive control (control group). Results showed that P3 and P3-M2 had the ability of reducing lipid and protein oxidantion during fermentation. The increase of lipoxygenase activity and thiobarbituric acid reactive substances (TBARS) values were retarded. Metmyoglobin(MetMb) content relatively decreased significantly(p < 0.05), while sulfhydryl group contents were significantly higher than those in the control((p < 0.05). Futhermore, changes in protein bands were confrimed with the less protein oxidation with P3-M2 than P3 and the control. Additionally, strain P3 and P3-M2 significantly enhanced the type and relative content of esters after fermented (p < 0.05), indicating that strain P3 and P3-M2 contributed to the production of flavor substances. These results revealed that L. plantarum strains with antioxidant properties were a promising approach in inhibiting lipid and protein oxidation of chinese sausage, maintaining the stable natural structure of protein, simultaneously improve the quality of sausage and promote the sausage to form a better flavor.

The construction industries face several challenges related to productivity. Productivity mainly depends upon labour effort and performance. The poor productivity of labour is one of the major reasons of time over-runs and increasing cost in construction projects. Our study aims to build a comprehensive assessment on the relationship between various factors that affect labour productivity in the construction of prestressed concrete Buildings in Ghana. A sample of 200 re-spondents collected from workers of Construction Company in Ghana. The questionnaire was designed which comprises two parts; the first part contains background information of the staff of construction company while second section explores the opinion of the staff regarding factors af-fecting labour productivity. The Smart-PLS was utilized to analyze and estimate the relationship among construct variables. By utilizing relative importance index and multiple linear regressions, it is identified that the management factor such as inadequate incentives; material factor such as poor quality of material; labour factors such as poor quality and training of labors; supervision factor such as incompetence of site supervisor; equipment factor such as frequent damage of equipment have a negative and significant relationship with labour productivity in the construc-tion of prestressed concrete buildings in Ghana. The findings of this study recommend that in order to improve labour productivity, the construction industries must conduct labour productivity measurements by adopting schedule for procurement of materials, safety programs, motivational system, and frequent meeting with project professionals.

The composition of bacteria in the gastrointestinal tract of piglets is easily affected by environmental changes, particularly during the weaning period. Compound strains of Lactobacillus reuteri and Lactobacillus salivarius were supplemented to piglets during pre- and post-weaning to determine their effects in improving the growth performance and ameliorating the diarrhea rate and stress caused by antioxidation in piglets. A larger number of L. reuteri and L. salivarius colonized the distal segment of the ileum and the total numbers of Lactobacillus spp. and Bifidobacterium were higher in the ileal mucous membrane and cecal lumen with probiotics supplementation. The numbers of antioxidative and immune molecules were increased in the plasma following compound bacteria (CL) supplementation, whereas cortisol and endotoxin levels were lower and growth hormone and insulin-like growth factor 1 were higher. Spearman’s and KEGG analysis of the bacterial operational taxonomic unit and antioxidative and immune indices and metabolic genes indicated that the body growth modulation by CL supplementation could be attributed to optimization of the intestinal bacterial composition. Collectively, these results suggest that supplementation with CL could reduce stress and improve the growth performance of piglets during weaning by optimizing the intestinal bacterial composition.

An improved synthesis of glucosyl esters was reported here, avoiding the use of expensive Ag reagent as well as the hydrolysis of instable glucosyl bromide. Notably, ß-configuration product was exclusively obtained in good yield.

Polychlorinated phenoxathiins (PCPTs), polychlorinated dibenzothiophenes (PCDTs), and polychlorinated thianthrenes (PCTAs) are sulfur analogues of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/DFs). Chlorothiophenols(CTPs) and chlorophenols (CPs) are key precursors to form PCTA/PT/DTs, which can form chloro(thio)phenoxy radical, sulfydryl/hydryl-substituted phenyl radical and (thio)phenoxyl diradicals. The available radical/radical PCTA/DT formation mechanism failed to explain the higher concentration of PCDTs than that of PCTAs under the pyrolysis or combustion conditions. Thus in this work, a detailed thermodynamics and kinetic calculations were carried out to investigate the pre-intermediates formation for PCTA/PT/DTs from radial/molecule coupling of 2-C(T)P with their key radical species. Our study found that the radial/molecule mechanism can thermodynamically and kinetically contribute to the gas-phase formation of PCTA/PT/DT/s. The S/C coupling modes to form thioether-(thio)enol intermediats are preferable over the O/C coupling modes to form ether-(thio)enol intermediats. Thus, although the radial/molecule coupling of chlorophenoxy radical with 2-C(T)P have no effect on the PCDD/PTs formation, the radial/molecule coupling of chlorothiophenoxy radical with 2-C(T)P play an important role in the PCDT/PT formation. Most importantly, the pre-PCDT intermediates formation pathways from the coupling of sulfydryl/hydryl-substituted phenyl radical with 2-C(T)P and the coupling of (thio)phenoxyl diradicals with 2-C(T)P are more favorable to pre-PCTA/PT intermediates formation pathways from the coupling of chlorothiophenoxy radical with 2-C(T)P, which can give reasonable explanation for the high PCDT-to-PCTA ratio in the environment.

Three-dimensional flexible piezoresistive porous sensors have been used in health diagnosis and wearable devices. By utilizing 3D printed sacrificial mold casting with highly conductive polymer composites, porous sensors with high conductivity and complex structures were achieved. Traditional conductive polymer composites are usually heated using external heat sources, which are time and energy consuming. However, in this study, conductive porous sensors with triply periodic minimal surface (TPMS) structures were manufactured using self-resistance electric heating by utilizing the conductive nature of the polymers. The porous structures were designed based on Diamond (D), Gyroid (G), and I-WP (I) unit cells of the TPMS. The use of self-resistance electric heating has improved the compression performance and piezoresistive response of the structures. Among these structures, the D-based structure exhibited the maximum response strain (61 %), with a corresponding resistance response value of 0.97, which increased by 10.26 % compared to that of the structures heated by using the external heat sources. This study offers a new perspective on designing and optimizing porous materials with specific functionalities, particularly in the realm of flexible and portable piezoresistive sensors.

Due to the low content, few studies are focused on the volatile compounds of Phlomoides rotata (Benth. ex Hook. f.) Mathiesen (PR, syn. Lamiophlomis rotata (Benth.) Kudô). However, such volatile compounds may have important pharmacological activities such as antioxidant, anticancer. In order to identify the chemical markers (CMs) in the essential oils (Es) and explore the potential bioactivities, we first conduct a thoroughly investigation on the volatile compounds and evaluate their anti-oxidant activities (AOAs), to the best of our knowledge. Light yellow Es with a fresh and elegant smell are obtained by hydro-distillation with an average yield of 0.11% (mL/g). After separation through cryoprecipitation, the crystals (Cs) and EOs removed crystals (RCs) were gotten, respectively. A total of 81 components are qualified and quantified in the Es, Cs and RCs, in which 44 ones are first reported from PR. As for content, the main compounds are long-chain fatty acids (LCFAs) and their esters. Among them, palmitic acid (PA), myristic acid (MA), linoleic acid (LA), oleic acid (OA) and methyl palmitate are highlighted, Besides, hexahydrofarnesyl acetone and phytol are also prominent Four kinds of C13-norisoprenoids are first reported from PR, in which, trans-β-damascenone is potent in flavour. In sum, these eight representative compounds can be chosen as the CMs. The AOAs of Es, Cs, RCs and four CMs such as PA, MA, LA and OA are evaluated by in vitro assays. In general, PA and MA present pro-oxidant activities (POAs) or weak AOAs. LA and OA show POAs or weak AOAs in lower concentration group, whereas demonstrate medium or strong AOAs in higher concentration group. Usually, the RCs demonstrate stronger AOAs and the Cs present weaker AOAs compared with those of the corresponding Es, which should be related to their different content of PA. This study can give some hints on the utilization of such Es which are abundant in LCFAs.

Due to the low content, few studies are focused on the essential oils (EOs) of Phlomoides rotata (Benth. ex Hook. f.) Mathiesen (syn. Lamiophlomis rotata (Benth.) Kudô. This plant has been used to treat rheumatic arthritis and grasserie in China. However, such EOs may have important pharmacological activities such as anti-cancer. To identify the chemical markers (CM) in the EOs and evaluate their antioxidant activities (AAs), we firstly conduct a thoroughly investigation on their chemicals and AAs, to the best of our knowledge. Light yellow EOs with fresh and elegant smell are obtained by hydro-distillation with average yield 0.11% (volume mL/weight g). The crystals are separated from the EOs through cryoprecipitation, respectively. A total of 81 components are qualified and quantified in the EOs, crystals and EOs removed crystals, in which 44 ones are first reported. As for content, the main compounds are long-chain fatty acids (FAs) and their esters. The most abundant one n-hexadecanoic acid (palmitic acid, PA) accounting for 43.15-54.8%, 58.49-64.57% and 15.9-41.1%, in the EOs, crystals and EOs removed crystals, respectively. Seven compounds including PA, tetradecanoic acid, linoleic acid, oleic acid, methyl hexadecanoate, hexahydrofarnesyl acetone and phytol can be chosen a the CMs in these EOs. The AAs are evaluated through in vitro assays. PA presents pro-oxidant activities in a concentration dependence manner. Usually, the EOs removed crystals demonstrate stronger AAs, and the crystals demonstrate weaker AAs compared with that of the corresponding EOs, which is related to the different content of PA in these samples. This study can give some hints for the utilization of such EOs which are abundant in FAs such as PA.

Chaphamaparvovirus (ChPV) is an ancient virus that has been detected in a variety of hosts. In this study, based on the phylogenetic analysis and the adaptability of ChPV to multiple hosts, we evaluated the potential of feline (FeChPV) and canine ChPV (CaChPV) for cross-species transmis-sion. Phylogenetic analysis showed that FeChPV and CaChPV were closely related. Notably, two strains of ChPVs isolated from domestic cats and 2 from dogs clustered together with CaChPVs and FeChPVs, respectively, suggesting the stringent boundaries between canine and feline ChPV may be broken. Further analysis revealed that CaChPV and FeChPV were more adapted to dogs than to cats, strongly suggesting the possibility of unidirectional or bidirectional transmission be-tween dogs and cats. Mutation analysis identified several shared mutations in cross-species-transmissible strains that were not located within immune epitopes. Furthermore, the VP struc-tures of FeChPV and CaChPV exhibited a high degree of similarity across both cross-species-transmissible and non-cross-species-transmissible strains. However, definitive experimental evi-dence is lacking, and its capacity for cross-species transmission should be approached with cau-tion and elucidated in further studies.

A sensitive electrochemical sensor based on AuPtPd trimetallic nanoparticles functionalized multi-walled carbon nanotubes coupled with chitosan modified glassy carbon electrode (GCE/CS/MWCNTs-AuPtPd) for the rapid detection of bisphenol A (BPA) was proposed. AuPtPd trimetallic nanoparticles were first assembled on MWCNTs to obtain MWCNTs-AuPtPd nanocomposite. Then the MWCNTs-AuPtPd was further dispersed on the surface of chitosan modified electrode surface to fabricate the GCE/CS/MWCNTs-AuPtPd sensor. Due to the superior catalytic properties of MWCNTs-AuPtPd and the good film formation of chitosan, the constructed sensor displayed good performances for BPA detection. The structural morphology of CS/MWCNTs-AuPtPd was characterized by many methods, such as SEM, UV-vis and TEM. Under the optimal conditions, the designed sensor showed a linear range from 0.05 to 100 µM for BPA detecting with a low detection limit of 1.4 nM. The designed sensor was further used to realize the determination of BPA in real samples and the recoveries ranged from 94.4% to 103.6%. The results demonstrated that the electrochemical sensor designed by CS/MWCNTs-AuPtPd nanocomposites was reliable and could be a useful tool for the monitoring of food safety.

Chronic renal failure (CRF) is a major public health problem worldwide. In this work, we investigated the effects of a purified Laminaria japonica polysaccharide (LJP61A) on the renal function using adenine-induced CRF mice model. Results exhibited that adenine treatment caused serious renal pathological damages and elevation of serum creatinine and blood urea nitrogen of mice. However, these changes could be significantly reversed by the administration of LJP61A in a dose-dependent manner. Additionally, LJP61A could dramatically reduce the weight loss, improve the urine biochemical index, and regulate the electrolyte disturbance of CRF mice. These results suggested that the renal functions of adenine-induced CRF mice could be improved by LJP61A, which might be developed to a potential therapeutic agent for CRF patients.

Multimodal knowledge graph completion necessitates the integration of information from multiple modalities (such as images and text) into the structural representation of entities to improve link prediction. However, most existing studies have overlooked the interaction between different modalities. To address this issue, this paper proposed a Transformer-based knowledge graph link prediction model (MM-Transformer) that fuses multimodal features. Different modal encoders are employed to extract structural, visual and textual features, and hybrid key-value calculations are performed on features from different modalities based on the Transformer architecture. The similarities of textual tags to structural tags and visual tags are calculated and aggregated respectively, and multimodal entity representations are modeled and optimized to reduce the heterogeneity of the representations. Experimental results demonstrate that, compared to the current multimodal state-of-the-art methods, the proposed method achieves significant performance improvements in knowledge graph link prediction tasks. This proves that the proposed method effectively addresses the problem of multimodal feature fusion in knowledge graph link prediction tasks.

In this study, we explored terahertz (THz) optical properties of the as-deposited and rapid thermal annealing (RTA) at 400°C, 600°C and 800°C of indium-tin-oxide (ITO) thin-films sputtered on high-resistivity silicon (HR-Si) substrate. We further investigated THz frequency dependence complex refractive indices and conductivity of those as-prepared and annealed ITO thin films. We note the transmittance enhanced from 27 % to 39 % for ITO thin film treated with RTA at 800°C while the real part of conductivity improved from 1019 Ω-1∙cm-1 to 4881 Ω-1∙cm-1 for ITO thin film treated with RTA at 600°C in the frequency range of 0.2 to 1 THz. The mobility, carrier concentration, plasma frequency and relaxation time of those sample were also deduced by fitting the experimental results with the Drude-Smith model. For example, the mobility of 29 cm2/V∙s, 110 cm2/V∙s, 226 cm2/V∙s and 70 cm2/V∙s, respectively is deduced for as-deposited, RTA at 400°C, RTA at 600°C and 800°C of ITO thin-films. In addition, the optical bandgap of those ITO thin films were evaluated with a typical Tauc plot showing extrapolation of photon energy spectrum. The transmittance, absorption coefficient and complex refractive indices of those ITO thin films were extracted by Swanepoel method using experimental transmittance and reflectance spectrum throughout the wavelength range from 400 to 1000 nm. Moreover, as expected, the transmittance of the ITO thin film treated with RTA at 800°C is improved at the wavelength of the visible light spectrum. We also displayed the surface morphology, microscopic structural properties and typical chemical composition of as-deposited and RTA at 400°C, RTA at 600°C and 800°C of ITO thin-films. We strongly believed the present study will lead to further enhancement for THz optoelectronics applications.

Effective detection of isopropyl methylfluorophosphonate (GB, sarin), a type of organophosphine poisoning agent, is an urgent issue to be addressed in maintaining public safety. In this research, a gas-sensitive film material defined as poly (4-hydroxy-4,4-bis trifluoromethyl) - butyl-1-enyl) - si-loxane (SXFA) with the structure of hexafluoroisopropyl (HFIP) functional group was synthesized by using methyl vinylpropyl dichlorosilane and hexafluoroacetone trihydrate as initial materials. Synthesis process products were characterized by FTIR. SXFA was prepared on a 200 MHz shear surface wave delay line with spin coating method for GB detected. Detection limit of ＜ 0.1 mg/m3 was obtained through conditional experiments. Meanwhile, we also obtained the maximum re-sponse of 2.168 mV at 0.1 mg/m3 concentration, which indicting a much lower detection limit of SAW-SXFA sensor. Additionally, the maximum response standard deviation of 0.11 mV with a co-efficient of variation of 0.01, as well as the maximum recovery standard deviation of 0.22 mV with a coefficient of variation of 0.02 were also obtained through 5 repeated experiments. Results showed that the SAW-SXFA sensor has strong selectivity and reproducibility, good selectivity, positive detection ability, high sensitivity, and fast alarm performance for sarin detection.

Aqueous Zinc ion batteries (ZIBs) possess significant potential in large energy storage systems due to their cost-effectiveness and environmental protection. However, the limited voltage window and poor reaction kinetics of the cathode material are still bottlenecks, restricting the further development of ZIBs. In this work, we rationally design Ni-doped V2O5@3D Ni core/shell composite on carbon cloth electrode (Ni-V2O5@3D Ni@CC) by growing Ni-V2O5 on the free-standing 3D Ni metal nanonets for high-voltage and high-capacity ZIBs. Impressively, the embedded Ni doping increases the interlayer spacing of V2O5, extending the working voltage and improving the Zn2+ kinetics reaction of the cathode materials, at the same time the 3D structure with high specific surface area and superior electronic conductivity benefits to fast Zn2+ transport. Consequently, the as-designed Ni-V2O5@3D Ni@CC cathodes can operate within a wide voltage window from 0.3 to 1.8 V vs. Zn/Zn2+ and deliver a high capacity of 270 mAh g-1 at a high current density of 0.8 A g-1. In addition, the reversible Zn2+ (de)-incorporation reaction mechanisms in the Ni-V2O5@3D Ni@CC cathodes are investigated by multiple characterization methods. As a result, we achieve a big step toward the practical applications of commercial ZIBs.

In light of the current situation where no testing equipment is available for measuring thermal deformation of objects, this paper proposes a novel method for accurate and precise measurement. The method overcomes the limitations of previous approaches that relied on pitch angle. By utilizing the principle of biplane multiple reflections, a bivariate laser spot displacement analysis algorithm is devised to attain highly precise measurements of bivariate angles. Additionally, a temperature gradient comparison algorithm is introduced to calculate the indicator test results under specific temperature conditions. To validate the effectiveness and reliability of this method, a testing system is constructed and utilized. The results demonstrate that the thermal deformation angle change test achieves an impressive accuracy of 0.015″ and a rate of thermal deformation angle change of 0.3247″/°C. These values are in close agreement with the previously simulated analysis result of 0.359″/°C, with only a relative error of 9.55%. Therefore, the test results confirm the efficacy and reliability of this testing method along with the feasibility of the algorithm processing.

The nucleon-pair shell model (NPSM) with broken symmetry basis is studied. The results demonstrate the validity of NPSM with symmetry broken basis, which leads to a significant reduction in the dimensionality of the multi-pair configuration space. We have observed that the axial-deformed basis provides a satisfactory description of the low-lying spectrum, even without the need for the projection procedure. In the case of the triaxial-deformed basis, we have investigated the variation after angular momentum projection, indicating the potential for NPSM to find exact solutions in the half-closed system.

High-quality rice (Oryza sativa L.) is increasingly widely planted in China with the improvement of people's living standards and the achievement of rice breeding efforts in recent years. However, the agronomic and physiological performances of high-quality indica rice (HQIR) under different nitrogen(N) application conditions in southern China are little known. Two-year consecutive field experiments were conducted with two HQIR and two ordinary-quality indica rice (OQIR) varieties under moderate and high N application rates, with yield and yield components, biomass, N up-take, and their related traits investigated. We found that grain yields of HQIR were slightly de-creased, but grain yields of OQIR were significantly increased by 6.60%-8.88% under high N rate compared with moderate N rate in both years. Thereby, OQIR produced 8.34%-11.87% and 22.00%-22.50% higher grain yield than HQIR under moderate and high N rates, respectively. The different responses of grain yield to N application rates were mainly due to decreased grain set-ting rate in HQIR and increased spikelets m-2 in OQIR under high N rate. Furthermore, high N rate significantly reduced pre-anthesis AE and improved grain-leaf area ratio, while did not in-crease post-anthesis DM compared with moderate N rate in HQIR, which might result in carbon metabolic deterioration and imbalance of source-sink relationship and subsequently lower supply of carbohydrate to panicle. Our results suggest that a moderate N rate (165 kg N ha-1) is beneficial for HQIR varieties to balance the maximum grain yield and high quality in southern China

After long years of development, the technology of analyzing the working condition of power units based on vibration signals has had relatively stable applications, but the accuracy and the degree of automation and intelligence for fault diagnosis are still inadequate due to the limitations of the current development of key technologies. With the development of big data and artificial intelligence technology, the involvement of new technologies will be an important boost to the development of this field. To support the subsequent research, bibliometrics is used as a tool to sort out the development of the technology in this field at the macro level; at the micro level, the classical and key literature is studied to grasp the development status at the technical level and prepare for the selection of entry points to continue in-depth innovation afterwards.

Cigar stacking fermentation is a key step in tobacco aroma enhancement and miscellaneous gas reduction, which both have a great influence on increasing cigar flavor and improving industrial availability. To analyze the effect of cigar tobacco leaf (CTLs) microbial community structure on volatiles during cigar stacking fermentation, this study used multi-omics technology to reveal the changes in microbial community structure and volatiles of different cigar varieties during stacking fermentation, in addition to exploring the interaction mechanism of microbiome and volatiles. The results showed that the dominant microbial compositions of different CTL varieties during stacking fermentation were similar, which included Staphylococcus, Corynebacterium 1, Aerococcus, and Aspergillus. These dominant microbes mainly affected the microbial community structure and characteristic microorganisms of CTLs through microbial interactions, thereby influencing the transformation of volatiles. Characteristic microorganisms of different CTLs varieties such as Trichothecium, Trichosporon, Thioalkalicoccus and Jeotgalicoccus, were found to posively correlate with characteristic volatiles like megastigmatrienone 4, pyrazine, tetramethyl-, geranyl acetone, and 2-undecanone, 6,10-dimethyl-, respectively. This in turn affected the aroma and sensory quality of the CTLs. This study provides theoretical support for the analysis of the mechanism of microorganisms on volatiles and aroma, and development of microbial agents during cigar stacking fermentation.

Age-related Macular Degeneration (AMD) is the major cause of elders’ vision loss, early screening and treatment are the most efficient way to reduce the rate of blindness. AI-based methods based on ophthalmic images play great potential for AMD diagnosis. However, low levels of accuracy, robustness, and explainability are challenges for AI approaches applied in clinics. Thus, this study proposed a multi-type of data source fusion method and a multi-model fusion approach for AMD detection. Typical unsupervised (Hierarchical Clustering and K-Means), typical supervised (SVM, VGG-16, and ResNet) methods, and proposed methods (multi-source data fusion-based method and multi-model fusion-based approach) are compared based on Optical Coherence Tomography (OCT), Fundus Autofluorescence (FAF), regular color fundus photography (CFP) and Ultra-Wide field Fundus (UWF) images. Data preprocessing and enhancements of each type of data are discussed. A feature extraction based on unsupervised ML models, feature combination and normalization, and multi-layer perception (MLP) algorithm are involved in the proposed multi-source data fusion-based method. Supervised ML and DL models and a voting mechanism are involved in the multi-model fusion-based approach. Findings show that the proposed methods present a high performance of accuracy and robustness. A real-world UWF database is involved from Shenzhen Aier Hospital. Practical and theoretical contributions are delivered. A reference value for medical diagnosis based on multiple digital images is contributed.

This study aims to elucidate a soft computing approach for quantitative assessment of the scoring grade or rubrics for students in an outcome based education system. The intended approach resorts to a fuzzy membership based assessment of the different parameters of the scoring system, thereby yielding a novel and humanly assessment technique. The selection of the membership functions is based on the human behavior so as to make a realistic representation of the scoring strategy. The novelty of the proposed strategy lies in assigning fuzzy membership based weighted scores instead of simply assigning score bands to rubric categories, as is performed in normal rubrics based assessment. Comparative results demonstrated on a case study of Indian education scenario reveal the effectiveness of the proposed strategy over other fuzzy membership and normal rubrics based assessment procedures.

Ceftiofur (CEF) sodium is a third-generation broad-spectrum cephalosporin commonly used in an extra-label manner in dogs for the treatment of respiratory and urinary system infections. To contribute to the literature supporting CEF use in companion animals, we have developed a compartmental, nonlinear mixed-effects (NLME) model of CEF pharmacokinetics in dogs (PK). We then used the mathematical model to predict (via Monte Carlo simulation) the duration of time for which plasma concentrations of CEF and its pharmacologically active metabolites remained above minimum inhibitory concentrations (respiratory tractEscherichia coli spp). Twelve healthy beagle dogs were administered either 2.2 mg/kg ceftiofur-sodium (CEF-Na) intravenously (I.V) or 2.2 mg/kg CEF-Na subcutaneously (S.C). Plasma samples were collected over a period of 72 hours post-administration. To produce a measurement of total CEF, both CEF and CEF metabolites were derivatized into desfuroylceftiofur acetamide (DCA) before analysis by UPLC-MS/MS. No adverse effects were reported after I.V or S.C dosing. The NLME PK models were parameterized using the stochastic approximation expectation maximization algorithm as implemented in Monolix 2018R2. A two-compartment mamillary model with first-order elimination and first-order S.C absorption best described the available kinetic data. Final parameter estimates indicate that CEF has a low systemic clearance (0.25 L/h/kg) associated with a low global extraction ratio E = 0.02) and a moderate volume of distribution (2.97 L/kg) in dogs. The absolute bioavailability after S.C administration was high (93.7%). Gender was determined to be a significant covariate in explaining the variability of S.C absorption. Our simulations predicted that a dose of 2.2 mg/kg CEF-Na S.C would produce median plasma concentrations of CEF of at least 0.5 µg/mL (MIC₅₀) for approximately 30 hours.

This paper discusses about control of the linear switched reluctance machines (LSRMs) network for the zero phase-difference tracking to a sinusoidal reference. The dynamics of each LSRM is derived by online system identification and modeled as a second-order linear system. Accordingly, based on the coupled harmonic oscillators synchronization manner, a distributed control is proposed to synchronize each LSRM state to a virtual LSRM node representing the external sinusoidal reference for tracking it with zero phase-difference. Subsequently, a simulation scenario and an experimental platform with the identical parameter setup are designed to investigate the tracking performance of the LSRMs network constructed by the proposed distributed control. Finally, the simulation and experimental results verify the effectiveness of the proposed LSRMs network controller, and also prove that the coupled harmonic oscillators synchronization method can improve the synchronization tracking performance and precision.

This paper proposed emotion recognition methods for consecutive facial images, and implements the inference of neural network model on a field-programmable gate array (FPGA). The proposed emotion recognition methods are based on a neural network model architecture that combines convolution neural networks (CNNs), long short-term memory (LSTM), and fully connected neural networks (FCNNs), called CLDNN or ConvLSTM-FCN. This type of neural network mod-el can analyze the local feature sequences obtained through convolution of data, making it suita-ble for processing time-series data such as consecutive facial images. In this paper, sequences of facial images are sampled from videos corresponding to various emotional state of subjects. The sampled images are then pre-processed with the processes includes facial detection, greyscale conversion, resize, and data augmentation if necessary. The 2-D CNN in ConvLSTM-FCN is used for feature extraction for these pre-processed facial images. These sequences of facial im-age features are time sequences with dependent properties between the elements within them. The LSTM is then used to model these time sequences followed by fully connected neural net-works (FCNNs) for classification. The proposed consecutive facial emotion recognition method achieves an average recognition rate of 99.51% on RAVDESS dataset, 87.80% on BAUM-1s dataset and 96.82% on eNTERFACE’05 data set, using 10-fold cross-validation on the PC. Some com-parisons of recognition accuracies between the proposed method and the other existing related works are conducted in this paper. According to the comparisons, the proposed emotion recog-nition methods outperform the existing related researches. The proposed emotion recognition methods are then implemented on an FPGA chip using the neural network model inference algo-rithms in this paper, and the accuracies of the experiments conducted on the FPGA chip are iden-tical to those obtained on the PC. This verifies that the proposed neural network model imple-mented on the FPGA chip performs well.

As matrix representations of magic labelings of related hypergraphs, magic squares and their various variants have been applied to many domains. Among various subclasses, trimagic squares have been investigated for over a hundred years. The existence problem for trimagic squares with singly even orders and orders 16n has been solved completely. However, very little is known for the existence of trimagic squares with other even orders except for the only three examples and three families. We construct normal trimagic squares by using product constructions, row-square magic rectangles, and trimagic pairs of orthogonal diagonal Latin squares. We give a new product construction: For positive integers p, q, and r having the same parity other than 1, 2, 3, 6, if normal p × q and r × q row-square magic rectangles exist, then a normal trimagic square with order pqr exists. As its application, we construct normal trimagic squares of orders 8q^3 and 8pqr for all odd integers q not less than 7 and p,r ∈ {7, 11, 13, 17, 19, 23, 29, 31, 37}. Our construction can easily be extended to construct multimagic squares.

Large-scale volumetric fracturing is generally used during shale gas development. The return rate of fracturing fluid is low, and a large amount of slickwater will be retained in the reservoir. The adsorption and desorption of partially hydrolyzed polyacrylamide (HPAM), an additive commonly used in slickwater, on the surface of shale was studied using Longmaxi Shale from the Sichuan Basin. The experimental results showed that the mass ratio of the HPAM solution to shale reached saturation adsorption at 20:1 when the concentration of HPAM solution was 1000 mg/L and 25:1 when the concentration of HPAM solution was 500 mg/L. The mass ratio of the HPAM solution to shale was fixed at 25:1, and the adsorption equilibrium was reached at a HPAM concentration of 1000 mg/L when the aqueous solution temperature was 30°C and 800 mg/L when the aqueous solution temperature was 60°C. The Langmuir adsorption model yielded a better fit than the Freundlich adsorption model. The adsorption equilibrium time at 30°C was at 60 min for a HPAM concentration of 500 mg/L, while for a concentration of 1000 mg/L, it was at 90 min. The adsorption equilibrium time at 60°C was 40 min for a HPAM concentration of 500 mg/L, whereas it was 60 min for a HPAM concentration at 1000 mg/L. The pseudo-second order kinetics model yielded better fits than the pseudo-first order kinetics model. The adsorption of HPAM on shale was strong, and the adsorbed HPAM resembled cobwebs adhering to the shale surface. HPAM on the surface of shale after adsorption could resist the desorption capacity of water. However, when the amount of adsorbed HPAM on shale increased significantly, the amount of residual HPAM on the surface of the shale decreased rapidly during desorption in deionized water. The desorption of HPAM on the shale surface followed a modified desorption model. The higher the concentration of HPAM adsorbed on the shale surface was, the easier it was to desorb, the easier it was to be removed from the shale.

Conservation tillage and deep side-fertilization both hold the potential to reduce nitrogen leaching and improve grain yield and nitrogen use efficiency in fragrant rice cultivation practices. However, the combined impact of different tillage practices with deep side-fertilization on nitrogen leaching remains uncertain. Therefore, this study conducted on-site experiments for four rice growing seasons in both early and late seasons in 2018 and 2019, using the fragrant rice varieties "Meixiangzhan 2"(MX) and "Xiangyaxiangzhan"(XY). The four experimental treatments included:conventional tillage with regular fertilization (T1), conventional tillage with simultaneous deep fertilization (T2), reduced tillage with simultaneous deep fertilization (T3) , and no-tillage with simultaneous deep fertilization (T4). Our results indicate that the T4 treatment exhibited higher nitrogen leaching rates and potential nitrogen losses throughout the entire rice growth cycle, with a 4.51% increase in total nitrogen leaching and a 1.86% increase in potential nitrogen leaching compared to T1. In contrast, the T2 treatment demonstrated the lowest nitrogen leaching rate, resulting in a 6.01% reduction in total nitrogen leaching and a 9.57% decrease in potential nitrogen leaching compared to T1, demonstrating the most optimal performance. For MX, the T1 treatment resulted in lower daily grain outputs compared to the other treatments, with disparities ranging from 5.35% to 9.94%. Similarly, for the XY, the T1 treatment yielded significantly lower daily grain outputs compared to the other treatments, with discrepancies ranging from 6.26% to 10.81% during the late season of 2019. Overall, this study shows that conventional tillage with deep fertilization effectively reduces nitrogen leaching and boosts fragrant rice yields. Minimizing nitrogen leaching enhances nitrogen utilization efficiency. These insights highlight the significance of strategic fertilization and cultivation for environmental conservation and agricultural sustainability.

Background: Atherosclerosis (AS) is a chronic progressive disease caused by lipometabolic disorder. However, the pathological characteristics and mechanism of AS have not been fully clarified. By high fat and cholesterol diet induction, Tibetan minipig could be developed to the AS model animal which had a very similar pathogenesis to human AS. Methods: Here, we built the AS model of Tibetan minipigs and identified the differential abundance metabolites in the development of AS based on untargeted metabolomics. Results: We found that the sphingolipid metabolism and glucose oxidation were enriched in the AS group and the phenylalanine metabolism was reduced in the AS group. Moreover, in the development of AS, gluconolactone was enriched in the late stage of AS whereas biopterin was enriched in the early stage of AS. Conclusion: Gluconolactone and biopterin could be potential biomarkers for indicating the development of AS. Our research provides novel clues for the metabolic mechanism of AS from the perspective of metabolomics.

Magnesium (Mg) alloy is a widely used lightweight metal structural material due to its high specific strength and stiffness, excellent damping performance, and recyclability. Wrought Mg alloys are widely favored in fields such as aerospace, transportation, and biomedical stents. However, most wrought Mg alloys with a hexagonal close-packed (HCP) crystal structure lack sufficient independent slip systems to meet the von Mises criterion for uniform plastic deformation at room temperature. This can result in the formation of strong basal texture during plastic deformation and poor room temperature plastic forming ability. Improving the room temperature forming performance is a crucial challenge that must be addressed to broaden the application of Mg alloy sheets. Our research group has comprehensively summarized significant work and latest research progress in improving the room temperature forming of Mg alloy sheets via extrusion technology in recent years. Specifically, we have developed a new type of asymmetric extrusion technology that combines material structure evolution, mechanical property, and forming behavior analysis. We have elucidated the extrusion process characteristics, texture control mechanism, and forming properties of Mg alloy sheets through plastic deformation mechanisms, mold design, and finite element numerical simulation. Our findings provide a novel extrusion technology for the fabrication of highly formable Mg alloy sheets, which can be utilized in various applications.

Cooking is a very decentralized and private way of energy consumption in human activities. The existing investigation and statistical analysis can’t effectively calculate the proportion of population relying on clean cooking fuel and utilization technology in the region. Therefore, based on the big data of the earth, this paper adopts the combination of spatial analysis and statistical analysis to determine the survey sample area, and according to the economic conditions, topographic characteristics, national policies for new energy construction and living habits of the provinces and cities under investigation, the questionnaire survey is conducted for the research area to calculate the proportion of the regional population relying on clean cooking fuels and utilization technologies. Taking the south of the Yangtze River in China as an example, the paper effectively calculates that 88.25% of the population depends on clean cooking fuel and technology in this region, of which 89.81% are in urban areas and 79.87% are in rural areas. Analysis of the survey data shows that the proportion of the population using clean cooking fuels and technologies is related to factors such as economic development, income and resource endowment. There is a large urban–rural gap in terms of energy consumption tendency and structure in the south of the Yangtze River in China and cooking energy consumption in rural households also varies from region to region. The technical ideas and conclusions of the paper have high reference application value, which can help promote the upgrading of clean energy utilization and provide data basis for relevant decision and policy making.

Acanthamoeba keratitis (AK) is a blinding corneal infection caused by the protozoan Acanthamoeba. The long-term course of AK suggests the host immunity could not kill Acanthamoeba rapidly. The immune status is still unclear in the late stage of AK. The comparative transcriptome analysis was made based on the bulk RNA sequencing of cornea tissues from AK patients and donors. Differentially expressed genes and enriched signaling pathways were calculated. CIBERSORT algorithm was used for Immune infiltration analysis of cornea tissue between AK and normal controls. A total of 2668 differentially expressed genes, including 1477 upregulated genes and 1191 downregulated genes, were detected. Gene Ontology analysis revealed that the pathways were significantly enriched in leukocyte migration, regulation of T cell activation, the external side of plasma membrane, collagen-containing extracellular matrix, immune receptor activity and cytokine binding. KEGG pathway analysis showed that the pathways were significantly enriched in the cytokine-cytokine receptor interaction, hematopoietic cell lineage and Staphylococcus aureus infection pathway. The immune infiltration profiles varied little between AK and normal controls. Compared with normal tissue, cornea tissue of AK contained a higher proportion of M0 macrophages and CD8 T cells, while resting memory CD4 T cells contributed to a relatively lower portion (P &lt; 0.05). Finally, the expression levels of cell markers and SLAMF7/STAT6 pathway were confirmed by histopathology examinations, RT-qPCR and western blot.

The performance of the absolute atom gravimeters used on moving platforms, such as vehicles, ships and aircrafts, is strongly affected by the vibration noise. To suppress its influence, we summarize a vibration compensation method utilizing data measured by a classical accelerometer. The measurements with the accelerometer show that the vibration noise in the vehicle can be 2 order of magnitude greater than that in the lab during daytime, and can induce an interferometric phase fluctuation with a standard deviation of 16.70π. With the compensation method, our vehicle-mounted atom gravimeter can work normally in these harsh conditions. Comparing the Allan standard deviations before and after the vibration noise correction, we find a suppression factor of 22.74 can be achieved in static condition with an interrogation time of T = 20 ms, resulting a sensitivity of 1.35 mGal/Hz1/2, and a standard deviation of 0.5 mGal with an average time of 10 s. We also demonstrate the first test of an atom gravimeter in a moving vehicle, in which a suppression factor of 50.85 and a sensitivity of 60.88 mGal/Hz1/2 were realized with T = 5 ms.

Background: At present, the treatments for patients with advanced lung cancer focus on chemotherapy, targeted therapy, immunotherapy, or a combination of multiple treatments. Purpose: The main purpose of this study is to compare the various chemotherapy-based combination therapies and find the best one for patients with advanced lung cancer. Methods: Based on database (PubMed, EMBASE and Medline) for randomized controlled trials of advanced lung cancer with combination therapy from 2008 to 2020, we searched literatures with overall survival (OS), progression-free survival (PFS), objective response rate (ORR) and adverse as outcome indicators and established a Bayesian mesh meta-analysis for multiple treatment strategies. Then, we combined the results of four outcome indicators to find out the best chemotherapy-based combination therapy strategy for patients with advanced lung cancer, further, we tried to screen out the best drugs of which were commonly used now. Results: It contained a total of 51 studies, including five combination therapies: Chemotherapy/Chemotherapy plus placebo (CT), chemotherapy plus one targeted therapy drug (CT+T), chemotherapy plus two targeted therapy drugs (CT+T+T), chemotherapy combined with immunotherapy (CT+I) or chemotherapy combined with biotherapy (CT+B). In terms of four outcome indicators, CT+I showed the best therapeutic benefits. In the comparison of immunotherapy drugs, pembrolizumab showed the best effect. Conclusion: Our results showed that, among the multiple chemotherapy-based combination therapy strategies, chemotherapy combined with immunotherapy is the best choice for patients with advanced lung cancer, and pembrolizumab combined with chemotherapy has the best effect.

In order to quickly develop a multi ship collaborative collision avoidance plan in multi ship encounter scenarios, a multi ship collision avoidance decision model is proposed in accordance with the requirements of the International Maritime Collision Avoidance Regulations, taking into account the collision avoidance operations in multi ship encounter scenarios. Firstly, the collision risk between ships is determined by the closest encounter distance (DCPA) and closest encounter time (TCPA). Secondly, a decision objective function is established based on rules, degree of ship deviation, and ship risk. Finally, the prediction mechanism is used to calculate the minimum value of the objective function and complete the collision avoidance decision. The simulation results show that in the scenario of multiple ship encounters, the collision avoidance model can achieve safe collision avoidance with a smaller steering frequency and a shorter col-lision avoidance time. The proposed multi ship collision avoidance model can provide reference for collision avoidance decision-making in multi ship encounter scenarios, which helps to im-prove the collision avoidance efficiency in multi ship collision avoidance

Porcine sapovirus (PoSaV) is a significant pathogen causing diarrhea with high morbidity and mortality rates. Given its zoonotic characteristics, this study conducts a comprehensive genetic evolutionary analysis of PoSaV. Results confirmed PoSaV as the primary RNA virus in piglet feces (27.54%). Phylogenetic analysis identifies the prevalent PoSaV strain SHCM/Mega2023 in the GIII genogroup, involving a recombinant event with MK962338 and KT922089. The time tree revealed that the GIII genogroup exhibits the widest divergence time span, indicating a high likelihood of viral recombination. Further selective pressure calculations demonstrate that PoSaV was under purifying selection (dN/dS &lt; 1), with seven positively selected sites in VP1 protein which might be related to the antigencity. In conclusion, this study presents a novel genomic evolution of PoSaV, offering valuable insights into antigenicity and vaccine research.

The dual-station Interferometric Synthetic Aperture Radar (InSAR) system can overcome the physical limitations imposed by the baseline of single-station dual-antenna InSAR. It provides greater flexibility and can enhance elevation measurement accuracy through a well-designed baseline configuration.Unmanned aerial vehicles (UAV) equipped with dual-station InSAR, with relatively low cost and high flexibility, are useful for mapping and land resource exploration. However, due to challenges including spatiotemporal synchronization and motion errors, there are limited reports on UAV-borne dual-station InSAR. This paper proposes a comprehensive method for processing data from small UAV-borne dual-station InSAR by integrating two-way synchronization chain signals. The proposed method includes compensation for time and phase synchronization errors, trajectory refinement with synchronized chain and Position and Orientation System (POS) data, high-precision dual-station InSAR imaging and interferometric processing. Height inversion results based on the proposed method is also provided, demonstrating the effectiveness of the proposed method and improving interferometric accuracy at calibration points from 0.66 meters to 0.42 meters.

As research into the relationship between the gut microbiome and health continues to evolve, probiotics are garnering increasing interest among consumers. Fermentation is rec-ognized as an efficacious biotechnology for augmenting the nutritional and functional at-tributes of foods. In this study, the ameliorative effects of Lycium barbarum L. lyophilized powder fermented with Lactobacillus plantarum NXU0011 (LP+Ly) on dextran sodium sul-fate (DSS)-induced ulcerative colitis (UC) in mice were investigated employing immuno-histochemistry, qRT-PCR, macrogenomics, and metabolomics. The results revealed that LP+Ly intervention significantly ameliorated histopathological inflammation in the ulcer-ated colon, diminished the expression of inflammatory markers such as IL-6, P-STAT3, and miR-214, and enhanced the diversity of intestinal flora in the mouse model group. Moreover, there was an increase in abundance of beneficial bacteria, including Lactobacillus, Prevotella, and Akkermansia. Metabolomic analysis indicated that 15 metabolites, including citrulline, D-xylose, and α-ketoisovaleric acid, exhibited significant variations following LP+Ly inter-vention. The metabolic pathways that displayed substantial differences included tryptophan biosynthesis, arginine biosynthesis, and amino sugar and nucleotide sugar metabolism. By modulating arginine biosynthesis, LP+Ly effectively improved the intestinal inflammatory state, thus mitigating the effects of UC.

Cycas (family Cycadaceae), spread throughout tropical and subtropical regions, is crucial in con-servation biology. Due to the subtle morphological variations between species, a solid spe-cies-level phylogeny for Cycas is lacking. Because of the rapid progress in high-throughput se-quencing technology, it has become feasible to acquire complete chloroplast (cp) genome se-quences, which provide a molecular foundation for phylogenetic research. In the present study, we employed next-generation sequencing technology to assemble and analyze the chloroplast genomes of six Cycas plants, including their genome structure, GC content, and nucleotide di-versity. The Cycas chloroplast genome spans 162,038 to 162,159 bp and contains 131 genes, in-cluding 86 protein-coding genes, 37 transfer RNA (tRNA) genes, and 8 ribosomal RNA (rRNA) genes. Through a comparative analysis, we found that the chloroplast genome of Cycas was highly conserved, as indicated by the contraction and expansion of the inverted repeat (IR) re-gions and sequence polymorphisms. In addition, several non-coding sites (psbK-psbI, petN-psbM, trnE-UUC-psbD, ndhC-trnM-CAU, and rpl32-trnP-GGG) showed significant varia-tion. The utilization of phylogenetic analysis relying on protein-coding genes has substantiated the division of Cycas primarily into four groups. The application of these findings will prove valuable in evaluating genetic diversity and the phylogenetic connections among closely related species. Moreover, it will provide essential support for the advancement of wild germplasm re-sources.

(1) Background: The elderly who have chewing difficulty (CD) are prone to malnutrition, frail-ty, and sarcopenia, and those with insufficient physical activity (IPA) are also prone to frailty, overweight, and high blood cholesterol. There is an urgent need to prepare functional foods and to promote healthy physical activity for the elderly over 70 years of age to prevent poor nutri-tion and frailty. (2) Methods: This study prepared functional foods (FF) with softened chicken moose and milkfish without fin for the elderly and compared the different effects of FF from those of music aerobic exercise (MAE) on the complete blood counts, blood biochemistry, in-cluding nutrition index of albumin, and cholesterol levels, and frailty scores before and after in-stitution of FF and MAE among residents of long-term care institutes. (3) Results: The FF signif-icantly increased the high-density lipoprotein cholesterol and albumin levels. In contrast, MAE significantly increased red blood cells (RBC), and decreased the rates of frailty items on fatigue feeling and low physical activity. In comparison between FF and MAE groups, we found that the FF for 5 weeks significantly improved better on HDL-C and MCV while the MAE for 10 weeks improved significantly better on hematopoiesis as increases in red blood cells and platelets. (4) Conclusions: Results from this study suggest that FF and MAE for the elderly have different ef-fects on nutrition status, blood biochemistry and frailty. A combination of both FF and MAE might provide better benefits of nutrition status, physical function, and frailty for the elderly.

Emerging evidence has shown that microRNAs play pivotal roles in wound healing. MicroRNA-21 (miR-21) was previously found to upregulate in order to fulfill an anti-inflammation role for wounds. Exosomal miRNAs have been identified and explored as essential markers for diagnostic medicine. However, the role of exosomal miR-21 in wounds has yet to be well studied. In order to facilitate the early management of poorly healing wounds, we developed an easy-to-use, rapid, paper-based microfluidic-exosomal miR-21 extraction device to determine wound prognosis in a timely manner. We isolated and then quantitatively examined exosomal miR-21 in wound fluids from normal tissues, acute and chronic wounds. Eight improving wounds displayed lower levels of exosomal miR-21 expression after wound debridement. However, four instances of increased exosomal miR-21 expression levels were notably associated with patients with poor healing wounds despite aggressive wound debridement, indicating a predictive role of tissue exosomal miR-21 for wound outcome. Paper-based nucleic acid extraction device provides a rapid and user-friendly approach for evaluating exosomal miR-21 in wound fluids as a means of monitoring wounds. Our data suggest that tissue exosomal miR-21 is a reliable marker for determining current wound status.

Antisense oligonucleotides (ASONs) have proven potential for the treatment of various diseases. However, their limited bioavailability restricts their clinical application. New structures with improved enzyme resistance stability and efficient drug delivery are needed. In this work, we propose a novel category of ASONs bearing anisamide conjugation at phosphorothioate sites for oncotherapy. ASONs can be conjugated with the ligand anisamide very efficiently and flexibly in solution. The conjugation sites and ligand amount both influence anti-enzymatic stability and cellular uptake, resulting in changes in antitumor activity that are detectable by cytotoxicity assay. T6 (with double end AA-conjugation) was identified as the optimal conjugate, and its antitumor activity and the underlying mechanism were examined further in vitro and in vivo. This paper presents a new strategy for the design of nucleic acid–based therapeutics with improved drug delivery and biophysical and biological efficacy.

Certain studies have reported various insulin resistance responses to ambient heavy metal pollution, but few have reported such responses to occupational heavy metal pollution. Even fewer have demonstrated a relationship between mixture effects of heavy metals and insulin resistance in welding workers. Overall, we recruited 53 welders and 48 administrative staff from a shipyard located in northern Taiwan. Personal exposure to heavy metals was monitored for PM2.5 and urine. Blood samples from each participant were collected from the antecubital vein after fasting. Urine samples from each participant were collected in the same period as blood samples. The geometric mean levels for chromium (Cr), manganese (Mn), iron (Fe), cobalt (Co), nickel (Ni), copper (Cu), zinc (Zn), and cadmium (Cd) in the PM2.5 of the personal breathing zone and urinary Mn of welders were significantly higher than those in administrative staffs. Ambient Cr, Co, Ni, and Cu levels in the PM2.5 and urinary Cd were positively related to HOMA2-IR after adjusting for personal covariates (PM2.5-Cr: β=0.036, 95%C.I.: 0.002 to 0.070; PM2.5-Co: β=0.040, 95%C.I.: 0.002 to 0.077; PM2.5-Ni: β=0.054, 95%C.I.: 0.013 to 0.094; PM2.5-Cu: β=0.049, 95%C.I.: 0.010 to 0.088; U-Cd: β=0.209, 95%C.I.: 0.052 to 0.366, respectively). Our findings indicated the PM2.5 metal components and urinary metals were associated with increased insulin resistance in shipyard welders.

Biological micro-dissection has a wide range of applications in the field of molecular pathology. The current laser-assisted dissection technology is expensive, and laser radiation can lead to sample contamination. As an economical and pollution-free micro-dissection method, piezoelectric ultrasonic micro-dissection has a wide application prospect. However, the performance of the current piezoelectric ultrasonic micro-dissection technology is unsatisfactory. In this paper, a novel piezoelectric ultrasonic micro-dissection device based on a flexure mechanism is proposed in order to solve the problems of low dissecting precision and excessive wear of the dissecting needle caused by the harmful lateral vibration of the current piezoelectric ultrasonic micro-dissection device. By analyzing the flexibility of flexure hinge, the type of flexure beam and the optimal design parameters are determined. Through comparing the harmonic response simulation analysis of the micro-dissection device based on a flexure mechanism and the traditional micro-dissection device without the flexure mechanism, the newly designed micro-dissection device achieves the best vibration effect when the driving frequency is 28kHz, compared with the traditional micro-dissection device, the lateral vibration suppression effect is improved by 68%. Then, based on the 3D printing technology, a prototype of a novel micro-dissection device was produced, and its performance was tested. It was found that the flexure mechanism did indeed suppress the lateral vibration of the needle tip. Finally, the experiments of 5μm thick paraffin-embedded rat liver sections were carried out, and the effects of different dissecting parameters on the dissecting effect were analyzed, and the optimal dissecting parameters were obtained. By comparing the dissecting effects of the tissue sample and the wear condition of the needle tip between the novel micro-dissection device and the traditional micro-dissection device under their optimal dissecting parameters, it is proved that the suppression of harmful lateral vibration not only significantly improves the dissecting effect, but also improves the service life and durability of the dissecting needle, which is beneficial to reduce the equipment costs.

Based on the geologic conditions of natural gas hydrate (NGH) accumulations in the Shenhu area, northern slope of the South China Sea, this paper used a method of combining reservoir stimulation technique (RST) with depressurization to investigate the conversion efficiency of marine NGH reservoirs in different intrinsic permeability and initial NGH saturation conditions, and analyze the influence of variably-stimulation effect on marine NGH conversion efficiency in different accumulation conditions, provided a reference scheme for improving the NGH conversion efficiency in the Shenhu area. In this work, we performed calculations for the variations in CH4 production rate and cumulative volume of CH4 in different initial NGH saturation, intrinsic permeability and stimulation effect conditions, variance analysis and range analysis methods were used to analyze the significance of these key factors and their interaction, and investigated the sensitivity of stimulation effect on NGH conversion efficiency, respectively. The simulation results showed that stimulation effect have a significant influence on NGH conversion efficiency, and the influence of interaction between these three factors were not obvious. Possibly most important, we clarified an optimum stimulation effect for higher NGH conversion efficiency under different accumulation conditions, especially in low-permeability and high-saturation, which corresponding stimulation effect were different.

C-terminal Src kinase (CSK) is the major inhibitory kinase for Src family kinases (SFKs) through phosphorylation of their C-tail tyrosine site, and regulates various cellular activities in association with SFKs functions. As a cytoplasmic protein, CSK need be recruited to the plasma membrane to regulate SFKs activities. The regulatory mechanism for CSK activity and its subcellular localization remains largely unclear. In this work, we developed a genetically encoded biosensor based on fluorescence resonance energy transfer (FRET) to visualize CSK activity in live cells. The biosensor with optimized substrate peptide confirmed crucial Arg107 site in CSK SH2 domain, and displayed sensitivity and specificity to CSK activity while little responses to co-transfected Src and Fyn. FRET measurements showed CSK having relatively mild level of kinase activity in comparison to Src and Fyn ones in rat airway smooth muscle cells. The biosensor tagged with different submembrane-targeting signals detected CSK activity at both non-lipid raft and lipid raft microregions, while showed higher FRET level at non-lipid ones. Co-transfected receptor-type protein tyrosine phosphatase alpha (PTPα) had inhibitory effect on the CSK FRET response. The biosensor didn’t detect obvious changes of CSK activity between metastatic cancer cells and normal ones. In conclusion, a novel FRET biosensor was generated to monitor CSK activity, and demonstrated CSK activity existing in both non-lipid and lipid raft membrane microregions while more present at non-lipid ones.

The Eastern Himalayan Syntaxis (EHS), featured by an exceptionally intense compression orogeny and an extremely rapid surface erosion rate, stands out as a prime area for investigating surface processes and landscape evolution. Understanding the formation of the EHS holds significant importance in advancing our comprehension of the evolutionary dynamics within the Tibetan Plateau and the complex interplay between endogenic and exogenic geological processes. Currently, two models, namely the tectonic aneurysm and the syntaxis expansion model, have been proposed to explain the formation and evolution of this syntaxis. In this study, we employ a multi-disciplinary approach, integrating geomorphic indices such as slope, relief, Hypsometric Integral (HI), Normalized Channel Steepness (Ksn), River Slope-Basin Area Integration (χ), combined with erosion rates on long-medium-short term timescales obtained from thermochronology, cosmogenic nuclides 10Be and landslide disaster probability data. Our findings suggest a relatively high tectonic activity in the confluence of the Yigong and Parlung Rivers in the northern end of the syntaxis. Moreover, our data reveals that spatial variability of tectonic activity is the primary driver of regional geomorphologic features and the spatial-temporal characteristics of erosion observed in the EHS, with lithology and climatic precipitation playing a lesser role. Furthermore, the northwards migration of the EHS appears to elucidate the shift of tectonic activity and rapid erosion from the core of the syntaxis near the Namche Barwa towards the confluence of the Yigong and Parlung Rivers. This northwards migration of the EHS underscores the need for increased attention to the high geological hazard risk in the northern part of the EHS.

There have been many researches on the surface acoustic wave (SAW) sensors for detecting sulfur-containing toxic or harmful gases. This paper aims to give an overview of the current state of the polymer films used in SAW sensors for detecting deleterious gases. By covering most of the important polymer materials, the structures and types of polymers are summarized, and a variety of devices with different frequency, such as delay lines and array sensors for detecting mustard gas, hydrogen sulfide and sulfur dioxide are introduced. The preparation method of polymer films, the sensitivity of the SAW gas sensor, the limit of detection, the influence of temperature and humidity, and the anti-interference ability are discussed in detail. The advantages and disadvantages of the films are also analyzed, and the potential application of polymer films in the future is also forecasted.

Ultrasonic feedback energy is affected by the variety, planting and growth state of crops, it is difficult to fine application in precision agriculture systems. To this end, an ultrasonic sensor was mounted in a spray boom height detection system. Winter wheat was used as the test object to obtain feedback energy values for the spray boom height from the top of the wheat in the field during six critical growth stages: the standing stage, jointing stage, booting stage, heading stage, filling stage and maturity stage. The relationship between the actual value of the height from the spray boom to the top of wheat (Habw) and the detected value of the height from the spray boom to the top of wheat (Hdbw) was analyzed. A spray boom height detection model based on the ultrasonic sensor during the full growth cycle of wheat was determined. Field validation tests showed that the applicability of the spray boom height detection distance (Dd) of the spray boom height detection model proposed in the present study was 450 mm~950 mm. Within the applicable Dd range, the detection error of the detection model was ≤5 cm during the full growth cycle. This study provides an ultrasonic detection model construction method, which improves the reliability and accuracy of ultrasonic boom height detection for different wheat growth stages.

Elongate loach (Leptobotia elongata) is an endemic fish in China. Previous studies have provided some insights into the mitochondrial genome composition, and the phylogenetic relationships of L. elongata inferred using protein-coding genes (PCGs). However, the detailed information about is limited. Therefore, in this study, we sequenced the complete mitochondrial genome of L. elongata and analyzed its structural characteristics. The PCGs and mitochondrial genome were used for selective stress analysis and genomic comparative analysis respectively. The complete mitochondrial genome of the L. elongata, together with those of 36 Cyprinidae species, was used to infer the phylogenetic relationships of the Cobitidae family through maximum likelihood (ML) reconstruction. The results showed that the genome sequence has a full length of 16,591 bp, which includes 13 PCGs, 22 transfer RNA genes (tRNA), two ribosomal RNA genes (rRNA), and two non-coding regions (CR D-loop and light chain sub-chain replication origin OL). Overall, L. elongata shared the same gene arrangement and composition of the mitochondrial genes with other teleost fishes. The Ka/Ks ratios of all mitochondrial PCGs were less than 1, indicating that all the PCGs were evolving under purifying selection. Genome comparison analyses showed a significant sequence homology of species of Leptobotia. A significant identity between L. elongata and the other 5 Leptobotia species was observed in the visualization result, except for L. mantschurica, which lacked the tRNA-Arg gene and had a shorter tRNA-Asp gene. The phylogenetic tree revealed that the Cobitidae species examined here can be grouped into two clades, with L. elongata forming a sister relationship with L. microphthalma. This study could provide additional inferences for a better understanding of the phylogenetic relationships among Cobititdae species.

Milk fat globule membrane (MFGM) is a complex tri-layer membrane that wraps droplets of lipids in milk. In recent years, it has attracted widespread attention due to its excellent bioactive functions and nutritional value. The milk fat globule membrane contains a diverse array of bioactive lipids, including cholesterol, phospholipids, and sphingolipids, which play pivotal roles in mediating the bioactivity of the milk fat globule membrane. We sequentially summarize the main lipid types in milk fat globule membrane in this comprehensive review and outline the characterization methods used to employed them. In this comprehensive review, we sequentially describe the types of major lipids found in the milk fat globule membrane and outline the characterization methods employed to study them. Additionally, we compare the structural disparities among glycerophospholipids, sphingolipids, and gangliosides, while introducing the formation of lipid rafts facilitated by cholesterol. The focus of this review revolves around an extensive evaluation of current research on lipid isolates from the milk fat globule membrane, as well as products containing milk fat globule membrane lipids, with respect to their impact on human health. Notably, we emphasize clinical trials encompassing a large number of participants. The summarized bioactive functions of milk fat globule membrane lipids encompass regulation of human growth and development, influence on intestinal health, inhibition of cholesterol absorption, enhancement of exercise capacity, and anti-cancer effects. By offering a comprehensive overview, the aim of this review is to provide valuable insights into the diverse biologically active functions exhibited by lipids in milk fat globule membrane.

Light-colored and transparent polyimide (PI) films with good high-temperature dimensional stability are highly desired for advanced optoelectronic applications. However, in practice, the simultaneous achievement of good optical and thermal properties in one PI film is usually difficult due to the inter-conflicting molecular design for the polymers. In the present work, a series of PI-SiO2 nanocomposite films (ABTFCPI) were developed based on the PI matrix derived from hydrogenated pyromellitic anhydride (HPMDA) and an aromatic diamine containing benzanilide and trifluoromethyl substituents in the structure, 2,2'-bis(trifluoromethyl)-4,4'-bis[4-(4-aminobenzamide)]biphenyl (ABTFMB). The inorganic SiO2 fillers were incorporated into the nanocomposite films with the form of colloidal nanoparticles dispersed in the good solvent of N,N-dimethylacetamide (DMAc) for the PI matrix. The derived ABTFCPI nanocomposite films showed good film-forming ability, flexible and tough nature, good optical transparency, and good thermal properties with the loading amounts of SiO2 up to 30 wt% in the system. The ABTFCPI-30 film with the SiO2 content of 30 wt% in the film showed the optical transmittance of 79.6% at the wavelength of 400 nm (T400) with a thickness of 25 μm, the yellow index (b*) of 2.15, and the 5% weight loss temperatures (T5%) of 491 oC, which are all comparable to those the pristine ABTFCPI-0 matrix without filler (T400=81.8%; b*=1.77; T5%=492 oC). Meanwhile, the ABTFCPI-30 film exhibited obviously enhanced high-temperature dimensional stability with the linear coefficients of thermal expansion (CTE) of 25.4×10-6/K in the temperature range of 50 to 250 oC, which is much lower than that of the AMTFCPI-0 film (CTE=32.7×10-6/K).

Lead-free copper halide perovskite nanocrystals (NCs) are emerging materials with excellent photoelectric properties. Herein, we present a colloidal synthesis route of orthorhombic Cs2CuCl4 NCs with well-defined cubic shape and an average diameter of 24 ± 2.1 nm. The Cs2CuCl4 NCs exhibit bright deep blue photoluminescence, which is attributed to the Cu(II) defects. In addition, passivating the Cs2CuCl4 NCs by Ag+ can effectively improve the photoluminescence quantum yield (PLQY) and environmental stability.

Alzheimer’s disease (AD) is a neurodegenerative disease characterized by progressive memory loss and a decline in activities of daily life. Ventricular enlargement has been associated with worse performance on global cognitive tests and AD. Our previous studies demonstrated that brain sulfatides, myelin-enriched lipids, are dramatically reduced in subjects at the earliest clinically recognizable AD stages via an apolipoprotein E (APOE)-dependent and isoform-specific process. Herein, we provided pre-clinical evidence that sulfatide deficiency is causally associated with brain ventricular enlargement. Specifically, taking advantage of genetic mouse models of global and adult-onset sulfatide deficiency, we demonstrated that sulfatide losses cause ventricular enlargement without significantly affecting hippocampal or whole brain volumes using histological and magnetic resonance imaging approaches. Mild decreases in sulfatide content and mild increases in ventricular areas were also observed in human APOE4 compared to APOE2 knock-in mice. Finally, we provided Western blot and immunofluorescence evidence that aquaporin-4, the most prevalent aquaporin channel in the central nervous system (CNS) that provides fast water transportation and regulates cerebrospinal fluid in the ventricles, is significantly increased under sulfatide-deficient conditions, while other major brain aquaporins (e.g., aquaporin-1) are not altered. In short, we unraveled a novel molecular mechanism that may contribute to ventricular enlargement in AD.

A convenient and fast multiresidue method for the efficient identification and quantification of 72 pesticides belonging to different chemical classes in red and white grape wines have been developed. The analysis was based on gas chromatography tandem quadrupole mass spectrometric determination (GC–MS/MS). An optimization strategy involved the selection of MWCNTs amount and cleanup procedure cycle times for m-PFC was performed to achieve ideal recoveries and reduce sample matrix compounds in the final extracts. The optimized procedure obtained consistent recoveries between 70.2 and 108.8% (70.2% and 108.8% for white wine, 72.3% and 106.0% for red wine) , with relative standard deviations (RSDs) generally lower than 8.3% at three spiking levels of 0.01, 0.05 and 0.2 mg/kg. Linearity was studied in the range between 0.005 and 0.2 mg/kg using pesticide standards prepared both in pure solvent and in the presence of matrix, showing coefficients of determination (R²) higher than 0.985 for all the pesticides. To improve accuracy, matrix matched calibration curves were used for calculating the quantification results. Finally, the method was used successfully in detecting pesticide residues in commercial gape wines.

The MLL gene is a site of frequent rearrangement in acute leukemia with multiple fusion partners, but MLL-SEPT6 rearrangement is rare in clinical leukemia practice, and only 13 cases have been reported. We describe the case of an acute myelogenous leukemia child with MLL-SEPT6 rearrangement whose age of onset and accompanying gene mutations differs from previous reports. Considering the poor prognosis of leukemia children with MLL-SEPT6 rearrangement and the unsatisfactory results of existing treatments, the study of this case may provide new theories for diagnosis and treatment of MLL-SEPT6-associated childhood acute leukemia.

Background: Hepatocellular carcinoma (HCC) is one of most common cancers with a high mortality rate. HBV/HCV infection is an important risk factor to trigger HCC. Therefore, developing serum biomarkers for early diagnosis is crucial to prolong survival in HCC patients. Methods: An antibody array technology was utilized to detect serum from 20 HBV-related HCC patients, 20 chronic hepatitis B patients and 20 normal population, whose results were further validated by ELISA. Results: Both antibody array and ELISA showed that ten growth factors (SCF R, GDF-15, HGF, FGF-4, IGFBP-1, PIGF, GH, GDNF, BDNF and IGF-1) were significantly differential in HCC patients when compared to the non-HCC population. Among these growth factors, the levels of SCF R, GDF-15, HGF, GH and IGF-1 showed significant correlation with hepatitis B and its severity, indicating that these growth factors may promote HCC progression by an HBV-specific mechanism. A therapy targeting these growth factors in hepatitis B patients may help to prevent the development of HCC. FGF4 and GH were found, for the first time, to be upregulated in HCC, suggesting that these two growth factors may serve as novel serum biomarkers for the early diagnosis of HCC. Conclusion: The combined detection of all the differential growth factors may improve the diagnostic accuracy of HCC.

Human activities for exploitation and utilization of coastal zones have transformed coastline morphology and severely changed regional flow fields, underwater topography, and sediment distribution in the sea. In this study, single-beam bathymetry coupled with sediment sampling and analysis was carried out to ascertain submarine topography, geomorphology and sediment distribution patterns and explore sediment provenance in Qinzhou Bay, China. The results show the following. 1) The underwater topography in Qinzhou Bay is complex and variable, with water depths in the range of 0–20 m. It can be divided into four underwater topographic zones: the central (outer Qinzhou Bay), eastern (Sanniang Bay), western (east of Fangcheng Port), and southern (outside of the bay) parts. 2) Based on geomorphological features, the study area comprises four major submarine geomorphological units (i.e., tide-dominated delta, tidal sand ridge group, tidal scour troughs, and underwater slope) and two intertidal geomorphological units (i.e., tidal flat and abrasion platforms). 3) Sandy sediments are widely present in Qinzhou Bay, accounting for 70% of the total sediments. From the mouth of the Maowei Sea to the offshore, the sediments gradually become coarser, shifting from sandy mud to muddy sand, and then to fine sand and medium–coarse sand. The detrital minerals contained in the sediments mainly consist of quartz, feldspar, debris, ilmenite, leucosphenite, and tourmaline, whereas the clay minerals are dominated by kaolinite, followed by illite and smectite. The sediment provenance is mainly terrigenous input from near-source rivers. With sea reclamation and dam construction, outer Qinzhou Bay has experienced enormous morphological variation of its coastline. Together with the channel effect where the velocity of ebb tide is greater than that of flood tide, the underwater topography is characterized by increased scale and height difference of troughs and ridges as well as enhanced offshore deposition.

Objectives To determine the effects of omega-3 polyunsaturated fatty acids (ω-3 PUFA) from animal and plant sources on glucolipid metabolism and lipoprotein subfractions in type 2 diabetic patients with dyslipidemia. Methods Participants were recruited from the diabetes clinic at the Guanlin Hospital, Yixing City in Jiangsu province, China, from March 2017 through June 2017. Ninety participants were randomly assigned to take 3g/day fish oil (FO, containing EPA and DHA), 3g/day perilla oil (PO, containing ALA), or 3g/day blend oil containing fish oil and linseed oil (BO, containing EPA, DHA and ALA) for 3 months. The levels of serum glucose, glycated hemoglobin (HbA1c), C-peptide, triglyceride (TG), total cholesterol (TC), high-density lipoprotein (HDL), low-density lipoprotein (LDL), non-HDL, apolipoprotein A1 (Apo A1), apolipoprotein B (Apo B), lipoprotein a (Lp(a)), and free fatty acids were determined at baseline and after the 3 months. In addition, four fatty acids in serum and red blood cells membranes (RBCm) were analyzed using gas chromatography-mass spectrometry. The Lipoprint System was used to determine the lipoprotein subfractions. Results All 90 participants completed the final 3-month follow-up at the end of the study. After three months of intervention, blood glucose and HbA1c levels in the PO group were significantly lower than those at the baseline (p < 0.05). On the other hand, in the BO group, the HbA1c, non-HDL, Apo A1 and Lp(a) levels were significantly lower, while the C-peptide levels were significantly higher after intervention compared to the baseline (p < 0.05). In the FO group, the HbA1c and TG levels were significantly lower after the intervention compared to the baseline (p < 0.05). In addition, at the end of the study, there was significant increase in the levels of DPA and DHA in serum and RBCm of the FO group (p < 0.05), while in the BO group, there was significant increase in the levels of EPA, DPA and DHA in RBCm (p < 0.05). Finally, the FO group had the highest levels of large HDL subfractions compared to the BO and PO groups, but had the lowest levels of small HDL subfractions among the three groups. Conclusion For patients with diabetes, plant-derived ω-3 PUFAs are more effective at controlling blood glucose than animal-derived ω-3 PUFAs. However, animal-derived ω-3 PUFAs play a critical role in controlling blood lipids. Particularly, fish oil can effectively increase the beneficial large HDL subfractions and reduce the nonbeneficial small HDL subfractions. Both the animal- and plant-derived ω - 3 PUFAs have practical value in improving glucose and lipids metabolism in T2DM patients with dyslipidemia.

Air filtration mechanisms in the composite filter media used in practical applications are important and challenging to understand because the component fibers could have various size scales and morphologies. In this work, a three-dimensional digital model of nanofiber-based filter media was reconstructed for the first time based on the X-ray tomography data for the cellulose substrate and the Focused Ion Beam-Scanning Electron Microscope (FIB-SEM) image analysis for the several microns thick (3.82-7.90 μm) electrospun polyvinylidene fluoride (PVDF) nanofiber membrane. Besides the high-resolution model where the details of the fibrous structures were fully resolved, another low-resolution model with approximated unresolved structures was also established. Filtration simulations utilizing these models were conducted considering the drag force, Brownian diffusion and aerodynamic slip. The simulated filtration efficiencies agreed well with the experiments for particles of 70-400 nm, including the most penetrating particle size (MPPS, 100-200 nm). Moreover, the structure-resolved models had higher accuracy but higher computational costs, while the unresolved simulations saved much running time but over-predicted the filtration efficiency, especially for smaller particles (<100 nm). Our study presents a comprehensive strategy for investigating the composite filter media with multiscale complex structures using a combination of advanced characterization technologies and modular simulation models.

The mechanical hill wet-seeded rice machine is benefits to establish uniform seedling, and ditches were established by using this machine. However, little knowledge is known on the effect of the establishment of ditches on growth, lodging and yield, and their relationship with root traits. In this study, two field experiments were conducted during 2012 and 2013 with using two super rice varieties (i.e. hybrid rice ‘Peizataifeng’ and inbred rice ‘Yuxiangyouzhan’) grown under three ditches establishment treatments (i.e. T1: both water ditches and seed ditches were established by the machine, T2: seed ditches were established by the machine, T3: neither water nor seed ditches were established by the machine). The lodging index and lodging resistance traits, the grain yield and above-ground dry weight and the root traits were measured. The results showed that the lodging index was significantly affected by the treatments with ditches. The strongest lodging resistance was detected in mechanical hill wet-seeded rice with ditches treatment in both 2012 and 2013. The lodging resistance was strongly related to the breaking resistance, the root volume and root superficial area at the heading stage and maturity stage and the total root length at the heading stage. No significant difference was investigated in grain yield or dry weight of mechanical hill wet-seeded rice. Yuxiangyouzhan showed higher grain yield, dry weight and better lodging resistance but unfavorable root growth attributes than Peizataifeng. Therefore, the mechanical hill wet-seeded rice with ditches treatment increased rice lodging resistance is related to root traits.

Obesity has been identified as an emerging health concern for Chinese American children; however, very little is known about diets in Asian American children. The objective of our paper was to describe the dietary intakes of urban Chinese American schoolchildren using a state-of-the-art approach for dietary assessment. Data for this analysis come from the Food Journal Project 2017, a pilot and feasibility study conducted by a multi-sector collaboration. Children aged 8-12 (n=83) completed two dietary assessments using a food diary from January-June 2017. Children were then interviewed using the food diary as a guide and dietary data were entered into the online ASA24 system by study staff. Chinese American children were identified using surname, and were compared to non-Chinese peers with respect to nutrient intake and the Healthy Eating Index 2010 (HEI-2010). Chinese American children consumed more sodium dense diets, more protein, and less sugar compared to non-Chinese children. With regards to the HEI-2010, Chinese American children had less favorable whole grains and sodium scores; and more favorable seafood protein and empty calories scores compared to non-Chinese children. Sodium reduction and increasing whole grain intakes may be warranted in this group, but should be verified with additional studies.

Interviews from strength and conditioning coaches across all levels of athletic competition identified their two biggest concerns with the current state of wearable technology: (a) the lack of solutions that accurately capture data "from the ground up" and (b) the lack of trust due to inconsistent measurements. The purpose of this research is to investigate the use of liquid metal sensors, specifically Liquid Wire sensors, as a potential solution for accurately capturing ankle complex movements such as plantar flexion, dorsiflexion, inversion, and eversion. Sensor stretch linearity was validated using a Micro-Ohm Meter and a Wheatstone bridge circuit. Sensors made from different substrates were also tested and discovered to be linear at multiple temperatures. An ankle complex model and computing unit for measuring resistance values were developed to determine sensor output based on simulated plantar flexion movement. The sensors were found to have a significant relationship between the positional change and the resistance values for plantar flexion movement. The results of the study ultimately confirm the researchers' hypothesis that liquid metal sensors, and Liquid Wire sensors specifically, can serve as a mitigating substitute for inertial measurement unit (IMU) based solutions that attempt to capture specific joint angles and movements.

Teacher self-efficacy (TSE) significantly influences teacher well-being and pedagogical quality, thereby impacting student learning outcomes. Despite the recognized effectiveness of Lesson Study (LS) in shaping teachers' practices and beliefs, there is a research gap in TSE, particularly in higher education. To address this, we conducted a longitudinal study at a northeastern Chinese university, tracking TSE evolution in three English as a Foreign Language (EFL) teachers, encompassing both novices and experienced educators, during a six-month LS program. We collected both quantitative and qualitative data, encompassing interviews, surveys, and observations. Underpinned by Bandura and Wyatt's self-efficacy theory, the impact of LS on teachers' TSE development was explored and interpreted. Our findings shed light on the many ways in which LS effects individual teachers' TSE. Notably, both novice and experienced teachers improved significantly in TSE, especially in the domains of instructional techniques and student engagement. However, in the context of classroom management, there was considerably less growth. Furthermore, our research identifies a number of challenges that can have a negative impact on teachers' TSE, such as adapting to students' changing needs, dealing with limited resources, managing time constraints, navigating the school examination system, and overcoming initial resistance to the LS approach.

Wheat has a large and diverse repertoire of NLRs involved in disease resistance, with over 1,500 NLRs detected in some studies. These NLR genes occur as singletons or clusters containing copies of NLRs from different phylogenetic clades. The number of NLRs and cluster size can differ drastically among ecotypes and cultivars. Primarily, duplication has led to the evolution and diversification of NLR genes. Among the various mechanisms, whole genome duplication (WGD) is the most intense and leading cause, contributing to the complex evolutionary history and abundant gene set of hexaploid wheat. Tandem duplication or recombination is another major mechanism of NLR gene expansion in wheat. The diversity and divergence of duplicate NLR genes are responsible for the broad-spectrum resistance of most plant species with limited R genes. Understanding the mechanisms underlying the rapid evolution and diversification of wheat NLR genes will help improve disease resistance in crops. The present review focuses on the diversity and divergence of duplicate NLR genes and their contribution to wheat disease resistance. Moreover, we provide an overview of disease resistance-associated gene duplication and the underlying strategies in wheat.

The COVID-19 pandemic has disrupted the supply chain for personal protective equipment (PPE) for medical professionals, including N95-type respiratory protective masks. To address this shortage, many have looked to the agility and accessibility of additive manufacturing (AM) systems to provide a democratized, decentralized solution to producing respirators with equivalent protection for last-resort measures. However, there are concerns about the viability and safety in deploying this localized download, print, and wear strategy. Several polymer-based AM processes produce porous parts, and inherent process variation between printers and materials also threaten the integrity of tolerances and seals within the printed respirator assembly. The goal of this paper is to quantitatively measure particle transmission through printed respirators of different designs, materials, and AM processes, and assess the viability of printed respirators as N95 equivalents. Results from this study show that respirators printed using desktop/industrial-scale fused filament fabrication processes and industrial-scale powder bed fusion processes have insufficient filtration efficiency at the size of the SARS-CoV-2 virus, even while assuming a perfect seal between the respirator and the user’s face. Almost all printed respirators provided <60% filtration efficiency at the 100-300 nm particle range. Only one respirator, printed on an industrial-scale fused filament fabrication system provided >90% efficiency as-printed. Post-processing procedures including cleaning, sealing surfaces, and reinforcing the filter cap seal generally improved performance, but no respirator sustained the filtration efficiency of an N95 respirator, which filters 95% of SARS-CoV-2 virus particles. Instead, the printed respirators showed similar performance to various cloth masks. While continued optimization of printing process parameters and design tolerances could be implemented to directly print respirators that provide the requisite 95% filtration efficiency, AM processes are not sufficiently reliable for widespread distribution and local production of N95-type respiratory protection without commensurate quality assurance processes in place. Certain design/printer/material combinations may provide sufficient protection for specific users, but the respirators should not be trusted without quantitative filtration efficiency testing. It is currently not advised to expect printed respirators originating from distributed designs to replicate performance across different printers and materials.

Severe COVID-19 patients show impaired IFN-I response due to decreased IFN-β production, allowing persistent viral load and exacerbated inflammation. The SARS-CoV-2 nucleocapsid protein has been implicated in inhibiting IFN-I response through interfering with IFN-I signaling. This study reveals that SARS-CoV-2 nucleocapsid protein enhances interaction between human SUMO-conjugating enzyme UBC9 and MAVS. Increased MAVS-UBC9 interaction leads to enhanced SUMOylation of MAVS, inhibiting its ubiquitination, resulting in the inhibition of phosphorylation events involving IKKα, TBK1, and IRF3, disrupting IFN-I signaling. These results provide essential insights into the intricate regulation of the host's innate immunity during SARS-COV-2 invasion. Understanding these complex molecular mechanisms is crucial in developing effective therapeutic interventions against COVID-19 and potential future viral outbreaks.

BACKGROUND AND OBJECTIVE: The use of biomass for cooking carries significant health implications and can lead to adverse environmental issues such as deforestation, greenhouse gas emissions, and erosion. Despite these concerns, there is a lack of information about the nature and extent of cooking emissions in many developing countries. To address this gap, a study was conducted to assess cooking emission levels and their associated health effects among households in Dodoma City, Tanzania. METHODS: A descriptive cross-sectional design was conducted, involving 285 households in the peri-urban area of Dodoma City, Tanzania. A combination of questionnaires, observational checklists, and sampling devices (Aeroqual series 500 for Carbon Monoxide and Temptop PMD 351 for Particulate Matters) were employed for data collection, adhering to established protocols. Additionally, lung function tests were conducted with consent from the primary household cooks. Collected data were entered into an Excel spreadsheet and analyzed using STATA 17 software. FINDINGS: Out of 285 participants, 74.7% predominantly use charcoal for cooking, with 68.4% having outdoor kitchen setups. Significant differences in pollutant concentrations were observed across various fuel types (P=0.0001), with firewood emitting higher levels of particulate matter and carbon monoxide. Carbon monoxide concentrations during cooking were 6 times higher for firewood, 5 times higher for charcoal-gas, and 3 times higher for charcoal compared to WHO daily average limits. Additionally, a positive correlation between pollutant concentrations was noted (P-value = 0.0000). Lung problems 17.8% followed by eye irritation 15.7% were mentioned by those who claimed to know the health effects associated with cooking emissions. In addition, the spirometry test indicated that the majority of the participants had % predicted >80 while only 19% had % predicted below 50. CONCLUSION: Charcoal and firewood remain the primary cooking fuels in the study area despite their significant negative impacts. Our findings highlight a lack of awareness among community members regarding the health effects of biomass cooking emissions and insufficient guidance on constructing healthy kitchens. To address this, enforcing building standards, raising health awareness, and ensuring affordable access to modern fuels are crucial steps. These measures are essential for promoting healthier cooking practices and mitigating the adverse effects on households.

Sepsis is a life-threatening organ dysfunction caused by a dysregulated host response to infection, with septic cardiomyopathy being a common and severe complication. Despite its significant clinical impact, the molecular mechanisms underlying sepsis-induced cardiomyopathy (SICM) remain incompletely understood. In this study, we performed a comparative analysis of whole transcriptome profiles in two widely used mouse models of septic cardiomyopathy, the cecal ligation and puncture (CLP) model and the lipopolysaccharide (LPS) model. Our aim was to identify key genes and pathways involved in the development of septic cardiomyopathy and to evaluate the similarities and differences between the two models. Our findings suggested that 1) both methods can induce septic heart dysfunction within 24 hours; 2) distinct whole transcriptome expression profiles are revealed; 3) potentially different pathways are involved in causing heart failure in sepsis. The comprehensive comparison provides valuable insights into the molecular basis of septic cardiomyopathy and contributes to the ongoing search for effective treatment strategies, triggered by different factors for SICM.

Surgical methods for treating spasmodic torticollis include denervation and myotomy (DAM) of the affected muscles, and deep brain stimulation (DBS). This study reports on the long-term efficacy, prognostic factors, safety, and hospitalization costs following these two procedures. We collected data from 94 patients with spasmodic torticollis, of whom 41 and 53 were treated with DAM and DBS, respectively, from June 2008 to December 2020 at the Chinese People’s Liberation Army General Hospital. We used the Tsui scale and the global outcome score of the Toronto Western Spasmodic Torticollis Rating Scale (TWSTRS) to evaluate the preoperative and postoperative clinical condition in all patients. We also determined the cost of hospitalization, prognostic factors, and serious adverse events following the two surgical procedures. The mean follow-up time was 68.83 months (range = 13–116). Both resection surgery and DBS showed good results in terms of Tsui (Z = -5.103, P = 0.000; Z = -6.210, P = 0.000) and TWSTRS scores (t = 8.762, P = 0.000; Z = -6.308, P = 0.000). Compared with the DAM group, the preoperative (47.71, range 24–67.25) and postoperative (18.57, range 0–53) TWSTRS scores in the DBS group were significantly higher (Z = -3.161, P = 0.002). We found no correlation between prognostic factors and the patient age, gender, or disease duration for either surgical procedure. However, prognostic factors were related to the length of the postoperative follow-up period in the DBS surgery group (Z = -2.068, P = 0.039; Z = -3.287, P = 0.001). The mean hospitalization cost in the DBS group was 6.85 times that found in the resection group (Z = -8.284, P = 0.000). The total complication rate was 4.26%. We found, both resection surgery and DBS, showed good results in the patients with spasmodic torticollis. Although DBS had a greater impact on the quality of life and the degree of pain relief, it was more expensive. Prognostic factors were related to the length of the postoperative follow-up period in patients who underwent DBS surgery.

Carton detection is an important technique in the automatic logistics system and can be applied to many applications such as the stacking and unstacking of cartons, the unloading of cartons in the containers. However, there is no public large-scale carton dataset for the research community to train and evaluate the carton detection models up to now, which hinders the development of carton detection. In this paper, we present a large-scale carton dataset named Stacked Carton Dataset (SCD) with the goal of advancing the state-of-the-art in carton detection. Images are collected from the Internet and several warehouses, and objects are labeled using per-instance segmentation for precise localization. There are total of 250,000 instance masks from 16,136 images. Naturelly, a suite of benchmarks are established with several popular detectors. In addition, we design a carton detector based on RetinaNet by embedding our proposed Offset Prediction between Classification and Localization module (OPCL) and Boundary Guided Supervision module (BGS). OPCL alleviates the imbalance problem between classification and localization quality which boosts AP by 3.1%∼4.7% on SCD at the model level while BGS guides the detector to pay more attention to boundary information of cartons and decouple repeated carton textures at the task level. To demonstrate the generalization of OPCL to other datasets, we conduct extensive experiments on MS COCO and PASCAL VOC. The improvements of AP on MS COCO and PASCAL VOC are 1.8%∼2.2% and 3.4%∼4.3% respectively. Source dataset is available here.