Red mud (RM), a bauxite residue, contains hazardous radioactive wastes and alkaline material and poses severe surface water and groundwater contamination risks, necessitating recycling. Pretreated RM can be used to make adsorbents for water treatment. However, its performance is affected by many factors, resulting in a nonlinear correlation and coupling relationship. This study aimed to identify the best formula for an RM adsorbent using a mathematical model that examines the relationship between 11 formulation types (e.g., pore-assisting agent, component modifier, and external binder) and nine properties (e.g., specific surface area, wetting angle, and Zeta potential, among others). This model was built using a back-propagation neural networks(BP) based on single-factor experimental data and orthogonal test data. The model trained and predicted the established network structure to obtain the optimal adsorbent formula. The RM particle adsorbents had a pH of 10.16, specific surface area(BET) of 48.92 m2·g−1, pore volume of 2.10 cm3·g−1, compressive strength(ST)) of 1.12 KPa, and 24-h immersion pulverization rate(η_m) of 3.72%. In the removal of total phosphorus in flotation tailings backwater, it exhibited a good adsorption capacity (Q)and total phosphorous removal rate(η) of 48.63 mg·g−1 and 95.13%, respectively.

: Low-temperature growth of diamond films by chemical vapor deposition (CVD) method is not so widely reported and especially its initial periods of nucleation and growth phenomenon are of particular interest to the researchers. Four sets of substrates were selected for growing diamond films by linear antenna microwave plasma enhanced CVD (LA-MPCVD). Among them, silicon and sapphire substrates were pre-treated with detonation nanodiamond (DND) seeds before diamond growth for enhancement of its nucleation. On the other hand, carbon nanotube (CNT) films on Si substrates were also used as another template for LA-MPCVD diamond growth. In order to enhance the diamond nucleation during CVD growth, some of the CNT films were again pre-treated by electrophoretic deposition (EPD) of diamond nanoparticles. All these substrates were then put inside the LA-MPCVD chamber for growing diamond films under variable processing conditions. Microwave input powers (1100 – 2800 W), input power modes (pulse or continuous), antenna to stage distances (5 - 6.5 cm), process gas recipes (with or without CO2), methane gas percentages (3 - 5%), deposition times (11 – 120 minutes) were altered to investigate their effect on the growth of diamond film on the pre-treated substrates. The substrate temperatures were found to vary from as low as 170oC to a maximum of 307oC during the alteration of the different processing parameters. Contrary to the conventional MPCVD, it was observed that during the first hour of LA-MPCVD diamond growth, DND seeds or the nucleating structures, do not coalesce together to make a continuous film. Deposition time was the most critical factor in fully covering the substrate surfaces with diamond film, since the substrate temperature could not become stable during the first hour of LA-MPCVD. CNT was found to be oxidised rapidly under LA-MPCVD plasma conditions; therefore, a CO2-free process gas recipe was used to reduce CNT burning. Moreover, EPD-coated CNT was found to be less oxidised by the LACVD plasma during diamond growth.

Concrete-filled steel tube (CFST) members have been widely used in the field of civil engineering due to their advanced superior mechanical properties. However, internal defects such as concrete core voids and interface debonding are likely to weaken the load-carrying capacity and stiffness of these members, which affects safety and serviceability of CFST structures. Visualizing the inner defects of concrete core in CFST members have been a critical need in civil engineering construction, a travel time tomography (TTT) is introduced to quantitatively identify and visualize the sizes and positions of CFST members in this paper. Moreover, a parameter analysis is performed to investigate the relationship between TTT imaging qualities and influence factors, e.g. inversion parameters, defect sizes and positions. The effectiveness and accuracy of the TTT algorithm are verified by several numerical examples and the results demonstrate that TTT can identify the sizes and positions of concrete core void defects in CFST members efficiently and several inversion parameters including model weighting matrix and inversion grid size really pose a significant impact on the imaging results of CFST members. In addition, several optimum parameters are recommended to benefit the future study of the promising TTT approach for CFST members.

To promote low-carbon and green travel, this study proposes a tripartite evolutionary game model among new energy vehicle manufacturers, consumers, and government agencies. The game strategy combinations of each party and the stability conditions of the equilibrium point in the evolutionary game system are analyzed, and the validity of the conclusions is verified through simulation results. The study shows a strong correlation between the three parties in the evolutionary game system. From the perspective of car manufacturers, the probability of producing new energy vehicles is positively proportional to the subsidy received from new energy policy, the additional revenue gained from the management of the carbon trading scheme, and the fine received for producing conventional fuel vehicles. However, from the consumer perspective, the likelihood that consumers purchase new energy vehicles is positively related to the utility value to consumers and the coverage of public charging points in the city, and inversely related to the sales price of new energy vehicles. From the government perspective, a combination of direct subsidy policies and indirect support strategies should be considered to stimulate the rapid development of the new energy vehicle industry.

In this study, cement is used as the component that provides the stabilizing effect in order to evaluate the hardness and stability of loess soil. To assess the strength characteristics of loess soil reinforced with cement, samples were created with four different cement contents and three different curing times. The materials were put through a series of tests to determine their flexural strength, direct shear strength, indirect tensile strength, and unconfined compressive strength. An appropriate cement dosage was found, in addition to a durability index that could be used to quantify the effect of water absorption investigations on cement-stabilized loess. Both of these discoveries were made simultaneously. Analyses of investigations such as scanning electron microscopy (SEM) and energy dispersive X-ray fluorescence spectrometry (XRF) examinations were carried out so that the fundamental mechanics of the materials could be comprehended. According to the findings, the cohesion of cement-stabilized loess is significantly more sensitive to structure than the friction angle of the material, and the cohesion is responsible for the increase in shear strength after remolding. To get the desired level of strength, it is necessary to adjust the cement's proportions. In addition, as the curing period progresses, we see an increase in the cement-stabilized loess's resistance and stiffness. This is because of the interactions that take place between the structure and the mineral composition. It is believed that this event was caused by the cementation that occurs naturally. As a consequence of this reaction, the production of new cementitious materials takes place. The cation exchange that causes the hydration and pozzolanic reaction that leads to the creation of aggregates and interparticle flocculation is responsible for their production. These findings suggest that cement may be utilized as a simple and effective method of loess stabilization, which will ultimately result in improved performance of the loess.

Is human capital heterogeneity a decisive factor for Chinese enterprises to invest in Africa? Based on the Outward Foreign Direct Investment (OFDI） data of Chinese enterprises in 37 African countries from 2007 to 2017, this paper using the FGLS model, is the empirical analysis of the mechanism and effect of the human capital heterogeneity of host countries on OFDI location selection. The human capital heterogeneity can be divided into four dimensions: scale, quality, cost and structure, which can be measured by health level, education level, wage level, child dependency ratio and old-age dependency ratio. The results show that: (1) the host country's human capital scale and child dependency ratio structure have a significant positive impact on decision-making for OFDI; (2) the cost of human capital and the structure of old-age dependency ratio are negatively correlated with the inflow of OFDI; (3) different from the existing conclusions, the quality of human capital will inhibit the inflow of OFDI in the sample period; (4) the extended test shows that the quality of human capital has a significant positive impact on OFDI decision-making. The results of robustness test are reliable. Finally, according to the conclusion of this paper, policy recommendations are put forward.

The total amount of greenhouse gas emissions directly or indirectly generated by thermal power enterprises at any given time can be offset through afforestation, energy conservation and emission reduction. The present situation and control methods of CO₂ emission in China's coal-fired thermal power industry are introduced. The complex ecosystem is a unity of ecological functions composed of human society, economic activities and natural conditions. In the context of carbon neutrality and based on the theory of composite ecosystem, this paper divides the coal-fired thermal power plants in China into environmental management zones, calculates the atmospheric environmental capacity, and puts forward the concept of regional atmospheric environmental capacity, classification and zoning control. Finally, the management and control units are classified, and differentiated management and control requirements are put forward to provide a reference for regional air quality standard planning.

To fully appreciate genetics, one must understand the link between genotype (DNA sequence) and phenotype (observable characteristics). Advances in high-throughput genomic sequencing technologies and applications, so-called “-omics”, have made genetic sequencing readily available across fields in biology from applications in non-traditional study organisms to precision medicine. Thus, understanding these tools is critical for any biologist, especially those early in their career. This comprehensive review discusses the chronological development of different sequencing methods, the bioinformatics steps to analyzing this data, and social and ethical issues raised by these techniques that must be discussed and evaluated.

Petri nets are a graphical notation for describing a class of discrete event dynamic systems whose behaviours are charaterised by concurrency, synchronisation, mutual exclusion and conflict. They have been used over the years for the modelling of various distributed systems applications. With the advent of pervasive systems and the Internet of Things, the Calculus of Context-aware Ambients (CCA) emerged as a suitable formal notation for analysing the behaviours of these systems. In this paper, we are interested in comparing the expressive power of Petri nets to that of CCA. That is, can the class of systems represented by Petri nets be modelled in CCA? To answer this question, an algorithm is proposed that maps any Petri net onto a CCA process. We show that a Petri net and its corresponding CCA process behave the same way through experiments. It follows that CCA is at least as expressive as Petri nets, i.e. any system that can be specified in Petri nets can also be specified in CCA. Moreover, tools developed for CCA can also be used to analyse Petri nets.

Herein, activated red mud particles are used as an adsorbent for adsorbing phosphorus. Different concentrations of HCl and deionized water are used for desorption tests, and the optimal desorption mechanism is investigated. The Langmuir isothermal model and pseudo-second-order kinetic linear model produce consistent results: the desorption is dominated by the surface desorption of the monomolecular layer, and chemical desorption limits the rate of surface desorption. The desorption thermodynamics indicates that the desorption of phosphorus by the desorbent is spontaneous and high temperature promotes desorption. The particle diffusion model demonstrates that the removal of phosphorus in the form of precipitation from the surface of an activated hematite particle adsorbent occurs primarily via a chemical reaction, and an analysis of the microscopic morphology indicates that the desorption process is primarily accompanied by the dissolution of the metal element Ca, followed by Al and Fe. The desorbent reacts with the active elements in red mud, and the vibration of the [SiO4]2− group calcite or aragonite group of calcium–iron garnet in the functional group disappears. The intensity of the wave peaks of the PO43− groups decreases considerably. Thus, desorption primarily involves the chemical desorption of the monomolecular layer.

In this study, modified red mud after phosphorus adsorption was used as the adsorbent, and hydrochloric acid and deionized water were used as desorbents to desorb phosphorus. The components in the adsorbent were optimized based on density functional theory, and adsorbent and desorbent models were established. Molecular dynamics simulation was performed to determine the phosphorus concentration before and after desorption, interaction energies, radial distribution function(RDF), mean-square displacement(MSD), and diffusion coefficient. The Monte Carlo method was used to simulate the desorption isotherm, desorption site, heat of desorption, and desorption energy. Simulation results showed that deionized water could only desorb phosphorus on the adsorbent surface, and the stability of the system deteriorated upon adding hydrochloric acid. Hydrochloric acid destroyed the ionic and hydrogen bonding between the O atoms in H2PO4− and reactive metal and oxygen atoms in the activated red mud particles. Moreover, the van der Waals force decreased considerably. The ionic and hydrogen bonds between H2PO4− and the surface of activated red mud particles were broken by hydrochloric acid, which accelerated the desorption of phosphorus from the adsorbent surface. The interaction between hydrochloric acid and phosphorus accelerated the diffusion, which decreased the adsorption capacity. Moreover, the desorption capacity increased with increasing temperature.

Taking advantage of fact that the surface electrons of metallic nanoparticles (NPs) can be effectively released even at a low voltage bias, we demonstrate an improvement in the electrochemical performance of nano-sized Prussian Blue (PB) based secondary batteries by the incorporation of bare Ag or Ni NPs onto the vicinity of the working PB NPs. It is found that the capacity for electrochemical energy storage of the 17-nm-PB-based battery is significantly higher than the capacity of 10-nm-PB-based, 35-nm-PB-based or 46-nm-PB-based batteries. There is a critical PB size for the highest electrochemical energy storage efficiency. The full specific capacity CF of the 17-nm-PB-based battery stabilized to 62 mAh/g after 130 charge-discharge cycles at a working current of IW = 0.03 mA. The addition of 14 mass-percent of Ag NPs in the vicinity of the PB NPs gives rise to a 32% increase in the stabilized CF. A 42% increase in the stabilized CF can be obtained with the addition of 14 mass-percent of Ag NPs on the working electrode of the 35-nm-PB-based battery. An enhancement of CF is also found for electrodes incorporating bare Ni NPs but the effect is smaller.

HIV treatment strategies against viral enzymes are continuously hampered by viral drug resistance. Recent findings show that viral substrate Gag contributes to HIV-1 Protease Inhibitor (PI) resistance, leading to demands for new strategies in HIV treatment where Gag is recognized as a drug target. To successfully target Gag, there is a need of in-depth understanding of the Gag polyprotein and the effects of Gag mutations. Here, we propose new strategies in designing novel Gag inhibitors against existing and novel emerging Gag mutations via a structural understanding of the Gag-Protease relationship in PI resistance. In this review, we discuss the role of both novel and previously reported mutations, revealing insights to how they aid in PI resistance, and how new Gag inhibitors can be designed.

The apparent metal-insulator transition (MIT) in two-dimension (2D) was discovered by Kravchenko et al. [1] more than two decades ago in strongly interacting 2D electrons residing in a Si-metal-oxide-semiconductor field-effect transistor (Si-MOSFET). Its origin remains unresolved. Recently, low magnetic field reentrant insulating phases (RIPs), which dwell between the zero-field (B=0) metallic state and the integer quantum Hall (QH) states where the Landau-level filling factor υ > 1, have been observed in strongly correlated 2D GaAs hole systems with large interaction parameter rs (~20-40) and high purity. A new complex phase diagram was proposed, which includes zero field MIT, low magnetic field RIPs, integer QH states, fractional QH states, high field RIPs and insulating phases (HFIPs) with υ < 1 in which the insulating phases are explained by the formation of Wigner crystal. Furthermore, evidences of new intermediate phases were reported. All contribute to the further understandings of the puzzle. This review article serves the purpose of summarizing those recent experimental findings and theoretical endeavors, to foster future research efforts.

Wearable assistant devices play an important role in daily life for people with disabilities. Those who are hearing impaired may face dangers while walking or driving on the road. The major danger is their inability to hear warning sounds from cars or ambulances. Thus, the goal of this study is to develop a wearable assistant device for the hearing impaired to recognize emergency vehicle sirens on the road using edge computing. An EfficientNet-based fuzzy rank-based ensemble model was proposed to classify seven audio sounds, including human vocalizations and emergency vehicle sirens. This model was embedded in an Arduino Nano 33 BLE Sense development board. The audio files were respectively obtained from the CREMA-D dataset and Large Scale Audio dataset of emergency vehicle sirens on the road, with a total number of 8756 files. The seven audio sounds included neutral vocalization, anger vocalization, fear vocalization, happy vocalization, car horn sound, siren sound, and ambulance siren sound. The audio signal was converted into a spectrogram by the short-time Fourier transform as the feature. When one of the car horns, sirens, or ambulance sirens was detected, the wearable assistant device presented alarms through vibration and messages on the OLED panel. The performances of the EfficientNet-based fuzzy rank-based ensemble model in offline computing achieved an accuracy of 97.1%, precision of 97.79%, sensitivity of 96.8%, and specificity of 97.04%. In edge computing, the results were an accuracy of 95.2%, precision of 93.2%, sensitivity of 95.3%, and specificity of 95.1%. Thus, the proposed wearable assistant device has the potential benefit of helping the hearing impaired avoid traffic accidents.

Fibromyalgia (FM) is a complex, chronic, widespread pain syndrome that can cause significant health and economic burden. Emerging evidence has shown that neuroinflammation is an underlying pathological mechanism in fibromyalgia. Toll-like receptors (TLRs) are key mediators of the immune system. TLR4 is expressed primarily in microglia and regulates downstream signaling pathways, such as MyD88/NF-κB and TRIF/IRF3. It remains unknown whether electroacupuncture (EA) has therapeutic benefit in attenuating fibromyalgia pain and what role the TLR4 pathway may play in this effect. We compared EA with sham EA to eliminate the placebo effect due to acupuncture. We demonstrated that intermittent cold stress significantly induced an increase in mechanical and thermal FM pain in mice (mechanical: 2.48 ± 0.53 g; thermal: 5.64 ± 0.32 s). EA but not sham EA has analgesic effect on FM mice. TLR4 and inflammatory mediators-related molecules were increased in FM mice’s thalamus, medial prefrontal cortex, somatosensory cortex, and amygdala, indicating neuroinflammation and microglial activation. These molecules were reduced by EA but not sham EA. Furthermore, a new chemogenetics method was used to precisely inhibit SSC activity displayed an anti-nociceptive effect through TLR4 pathway. Our results imply that the analgesic effect of EA is associated with TLR4 downregulation. We provide novel evidence that EA can modulate the TLR4 signaling pathway, revealing potential therapeutic targets for FM pain.

Performance of the overhead squat may affect golf swing mechanics associated with golf-related low back pain. This study investigates the difference in lumbar kinematics and joint loads during the golf downswing between golfers with different overhead squat abilities. Based on the per-formance of the overhead squat test, 21 golfers aged 18 to 30 years were divided into the highest-scoring group (HS, N=10, 1.61 ± 0.05 cm, and 68.06 ± 13.67 kg) and lowest-scoring group (LS, N=11, 1.68 ± 0.10 cm, and 75.00 ± 14.37 kg). Data collection used a motion analysis system, two force plates, and TrackMan. OpenSim software was used to simulate the joint loads for each lum-bar joint. An independent t-test was used for statistical analysis. Compared to golfers demonstrat-ing limitations in the overhead squat test, golfers with better performance in the overhead squat test demonstrated significantly greater angular extension displacement on the sagittal plane, smaller lumbar extension angular velocity, and smaller L4-S1 joint shear force. Consequently, the overhead squat test is found to be a useful index to reflect lumbar kinematics and joint loading patterns during the downswing, and provides a good training guide reference for reducing the risk of a golf-related low back injury

This study aimed to use biomineralization technology to improve the bond strength of fiber-reinforced lightweight aggregate concrete (LWAC) after exposure to temperatures of 300 °C and 500 °C. The specimens of a control group (Group A) and two experimental groups (Group B and Group C) were prepared. These specimens healed themselves in different ways after exposure to high temperatures and pull-out tests. The self-healing method of Group A involved placing the specimen into an incubator. The self-healing method of Group B was the same as that of Group A. The self-healing method of Group C involved immersing the specimen in a mixed solution of urea and calcium acetate for two days, then taking it out and placing it in an incubator for two days. A cycle of four days was undertaken until the desired age was reached. After the specimens were healed to the planned age, the first and secondary pull-out tests and repair compound identification were carried out. After exposure to a temperature of 300 °C and self-healing for 90 days, compared with the specimens in Group A, the relative bond strength ratios of the secondary pull-out tests of the specimens in Group C increased by 20.3%. This indicates that biomineralization can effectively improve the bond strength of LWAC after high-temperature damage.

Biomimetic design has recently received widespread attention. Inspired by the Terebridae structure, this paper provides a structural form for suppressing vortex-induced vibration (VIV) response. Four different structural forms are shown, including the traditional smooth cylinder (P0), the Terebridae-inspired cylinder with a helical angle of 30° (P30), the Terebridae-inspired cylinder with a helical angle of 60° (P60), and the Terebridae-inspired cylinder with a helical angle of 90° (P90). And computational fluid dynamics (CFD) method is adopted to solve the flow pass the Terebridae-inspired structures, and the vibration equation is solved using the Newmark-β method. The results show that the VIV responses are effectively controlled in the lock-in region for P30, P60, and P90, and P60 shows the best VIV suppression performance. The transverse amplitude and the downstream amplitude can be reduced by 82.67% and 91.43% respectively for P60 compared with that for P0, and the peak of the mean-drag coefficient is suppressed by 53.33%. The Q-criterion vortices of P30, P60, and P90 are destroyed, with irregular vortices shedding. It is also found that the boundary layer separation is located on the Terebridae-inspired ribs. The twisted ribs cause the separation point to constantly change along the spanwise direction, resulting in the development of the boundary layer separation being completely destroyed. The strength of the wake flow is significantly weakened for the Terebridae-inspired cylinder. In the lock-in region, the motion trajectory presents a typical 8-shaped for P0, while the motion trajectory of the Terebridae-inspired cylinder tends to be a flat 1-shaped.

This paper presents a comprehensive study on the application and optimization of automotive thermoelectric generators (ATEGs), focusing on the crucial role of heat exchangers in enhancing energy conversion efficiency. Recognizing the substantial waste of thermal energy in internal combustion engines, our research delves into the potential of TEGs to convert engine waste heat into electrical energy, thereby improving fuel efficiency and reducing environmental impact. We meticulously analyze various heat exchanger designs, assessing their influence on the TEG's output power under different exhaust gas flow rates and temperatures. Furthermore, we explore the impact of TEG material properties on the overall energy conversion effectiveness. Our findings reveal that specific heat exchanger designs significantly enhance the efficiency of waste gas heat exchange, leading to an improved performance of the TEG system. We also highlight the importance of thermal insulation in maximizing TEG output. This study not only contributes to the ongoing efforts to develop more sustainable and efficient vehicles but also provides valuable insights into the practical application of thermoelectric technology in automotive engineering. Through this research, we aim to pave the way for more environmentally friendly transportation solutions, aligning with global efforts to reduce fossil fuel dependence and mitigate environmental pollution.

Gelidium jelly was traditionally made by boiling processed Gelidium seaweed and allowing the filtrate to congeal into jelly. The processing of Gelidium seaweed was very complicate involved the repeated procedures of water washing and sun drying for 7 times, and the seaweed was originally purple-red in color turned into yellow after the repeated wash and sun drying. This study aimed to evaluate the effects of halogen lamp drying methods in replace of sun drying on the physical-chemical qualities of Gelidium jellies. Properties included the agar yield, gelling temperature, hardness, springiness, rheological parameters, sensory attributes, color, and volatile compounds were investigated. The results demonstrated halogen lamp drying method required 12 times of washing and drying processes to achieve the similar jelly properties compared to sun drying for 7 times in the experimental conditions. Volatiles including heptanal, β-ionone, and (E)-2-decenal could be used as indicators to monitor the washing and drying processing. Halogen lamp was found could be an alternative processing method for seaweed drying, especially at rainy days.

Generally, when cognitive radio users are in Underlay mode, through the analysis of the electromagnetic spectrum in time, frequency, space, and field of multiple dimensional data accounts for judging the inherent correlation of the radio spectrum used/idle state, this is the realization of cognitive radio users (secondary users, SUs) efficient access to the foundation of the limited spectrum resources. Therefore, how to efficiently use of spectrum status of each SU implementation of reception multidimensional combination forecasting is the core of this paper addressing the problem. In this paper, we propose a deep-learning hybrid model called TensorGCN-LSTM based on the tensor data structure. The model treats SUs deployed at different spatial locations under the same frequency and the spectrum status of SUs themselves under different frequencies in the task area as nodes and constructs two types of graph structures. Graph convolutional operations are used to sequentially extract corresponding spatial-domain and frequency-domain features from the two types of graph structures. Then, the long short-term memory (LSTM) model is used to fuse the spatial, frequency, and temporal features of the cognitive radio environment data. Finally, the prediction task of the spectrum distribution situation is accomplished through fully connected layers. Specifically, the model constructs a tensor graph based on the spatial similarity of SUs' locations and the frequency correlation between different frequency signals received by SUs, which describes the electromagnetic wave's dependency relationship in spatial and frequency domains. LSTM is used to capture the electromagnetic wave's dependency relationship in the temporal domain. To evaluate the effectiveness of the model, we conducted ablation experiments on LSTM, GCN, GC-LSTM, and TensorGCN-LSTM models using simulated data. The experimental results show that our model achieved better prediction performance in RMSE, and the correlation coefficient R2 of 0.8753 also confirmed the feasibility of the model.

Infrared sensors incorporating suspended zinc oxide (ZnO) pyroelectric films and thermally-insulated silicon substrates are fabricated using conventional MEMS-based thin-film deposition, photolithography, and etching techniques. The responsivity of the pyroelectric film is improved through annealing at 500℃ for 4 h. The voltage response of the fabricated sensors is evaluated experimentally for a substrate thickness of 1 µm over a sensing range of 30 cm. The results show that the voltage signal varies as an inverse exponential function of the distance. A positioning system based on three infrared sensors is implemented in LabVIEW. It is shown that the position estimates obtained using the proposed system are in excellent agreement with the actual locations. In general, the results presented in this study provide a useful source of reference for the further development of MEMS-based pyroelectric infrared sensors.

Metal organic frameworks (MOFs) are used in catalysis due to their high specific surface area and porous structure. The dispersed active sites and limited reaction space render MOFs have the potential for highly selective electrocatalytic CO2 reduction reaction (ECO2RR). Meanwhile, formic acid (HCOOH) is attracting attention as a liquid product with high economic benefits. This review summarizes the MOFs and their derivatives applied for ECO2RR into HCOOH products. The preparation methods of MOFs as electrocatalysts and their unique advantages are discussed. A series of MOFs, and MOFs derivatives obtained by electrochemical reduction or carbonization processes are highlighted, including metal nanomaterials, carbon-based nanocomposites, single-atom catalysts, and bimetallic nanocomposites. Depending on the MOFs building units (metal ions and organic linkers) and the reaction conditions of derivatization, MOFs-based catalysts exhibit rich diversity and controllable modulation of catalytic performance. Finally, the challenges encountered at this stage and the future research directions of MOFs-based catalysts are proposed.

Accurately predicting the power of solar power generation can greatly reduce the impact of the randomness and volatility of power generation on the stability of the power grid system, which is beneficial for the balanced operation and optimized dispatch of the power grid system, and reduces operating costs. Solar PV power generation depends on weather conditions, which are prone to large fluctuations under different weather conditions. Its power generation is characterized by randomness, volatility and intermittency. Recently, the demand for further investigation and effective use on the uncertainty of short-term solar PV power generation prediction has been getting increasing attention in many application of renewable energy sources. In order to improve the predictive accuracy of output power of solar PV power generation and develop a precise predictive model, the authors worked predictive algorithms for the output power of a solar PV power generation system. Moreover, since short-term solar PV power forecasting is one of the important aspects for optimizing the operation and control of renewable energy systems and electricity markets, this review focuses on the predictive models of solar PV power generation, which can be verified in the daily planning and operation of a smart grid system. In addition, the predictive methods in the reviewed literature are classified according to the input data source used for accurate predictive models, and the case studies and examples proposed are analyzed in detail. The contributions, advantages and disadvantages of the predictive probabilistic methods are compared. Finally, the future studies of short-term solar PV power forecasting is proposed.

The outbreak of COVID-19 in 2020 caused significant disruptions to global shipping and the world economy. This paper aims to investigate the impact of the pandemic on global shipping by analyzing the Baltic Dry Index (BDI). The BDI is a metric that reflects the worldwide shipping costs and directs related to supply and demand conditions, making it an indicator of economic production. The study utilizes data from 2019 to 2021, before and after the outbreak of COVID-19, and considers 13 independent variables, including raw materials, energy, stock market indexes, global port calls, and confirmed COVID-19 cases to investigate how to influent the BDI. The study employs stepwise regression to select variables and build models before and after the pandemic. The findings reveal that the key factors affecting the freight index BDI before the outbreak are: international scrap steel prices, iron ore prices, and the Commodity Research Bureau Index. However, after the COVID-19 outbreak, the factors affecting the BDI changed to the Shanghai Index, global port calls, and the number of confirmed COVID-19 cases.

This paper discusses a passive control issue for Nonlinear Time-Varying (NTV) systems subject to stability and attenuation performance. Based on the modeling approaches of Takagi-Sugeno (T-S) fuzzy model and the Linear Parameter-Varying (LPV) model, a Parameter-Dependent Polynomial Fuzzy (PDPF) model is constructed to represent the NTV systems. According to Parallel Distributed Compensation (PDC) concept, a parameter-dependent polynomial fuzzy controller is built to achieve robust stability and passivity of PDPF model. Furthermore, the passive theory is applied to achieve the performance constraining the disturbance effect on the PDPF systems. To develop the stability criteria, by introducing a parameter-dependent polynomial Lyapunov function, one can derive some stability conditions which belong to the term of Sum-Of-Squares (SOS) form. Based on the Lyapunov function, two stability criteria are proposed to design the corresponding PDPF controller such that the NTV system is robustly stable and passive. Finally, a numerical example is applied to demonstrate the effectiveness of the proposed stability criterion.

Vascular calcification (VC) is associated with increased cardiovascular risks in patients with chronic kidney disease (CKD). Sodium-glucose cotransporter 2 inhibitors, like empagliflozin, can improve cardiovascular and renal outcomes. We assessed the expression of Runt-related transcription factor 2 (Runx2), interleukin (IL)-1β, IL-6, AMP-activated protein kinase (AMPK), nuclear factor erythroid-2-related factor (Nrf2), and heme oxygenase 1 (HO-1) in inorganic phosphate–induced VC in mouse VSMCs to investigate the mechanisms underlying empagliflozin’s therapeutic effects. We evaluated biochemical parameters, mean artery pressure (MAP), pulse wave velocity (PWV), transcutaneous glomerular filtration rate (GFR), and histology in an in vivo mouse model with VC induced by an oral high-phosphorus diet following a 5/6 nephrectomy in ApoE−/− mice. Compared to the control group, empagliflozin-treated mice showed significant reductions in blood glucose, MAP, PWV, and calcification, as well as increased calcium and GFR levels. Empagliflozin inhibited osteogenic trans-differentiation by decreasing inflammatory cytokine expression and increasing AMPK, Nrf2, and HO-1 levels. Empagliflozin mitigates high phosphate–induced calcification in mouse VSMCs through the Nrf2/HO-1 anti-inflammatory pathway by activating AMPK. Animal experiments suggested that empagliflozin reduces VC in CKD ApoE−/− mice on a high-phosphate diet.

Following the occurrence of a typhoon, quick damage assessment related to residents can facilitate quick dispatch of house repair and disaster insurance works. Employing a deep learning method, this study used aerial photos of the Chiba prefecture obtained following the Typhoon Faxai in 2019 to automatically detect and evaluate the roof damage. This study comprised three parts: training deep learning model, detecting the roof damage using trained model, and classifying the level of roof damage. The detection object comprised roof outline, blue tarps, and roof completely destroyed. The roofs were divided into three categories: roof without damage, roof with blue tarps and roof completely destroyed. the F value obtained using the proposed method was higher than those obtained using other methods. In addition, it can be further divided into 5 levels from level 0 to 4. Finally, the spatial distribution of the roof damage was analyzed using ArcGIS tools. The proposed method is expected to provide certain reference for the real-time detection of the roof damage after the occurrence of a typhoon.

Two secondary waste materials, municipal incinerator bottom ash (MIBA) and sewage sludge ash (SSA), were mixed with clay for ceramic manufacturing in this study. Specimens with 5 different MIBA replacement amount of 0%, 5%,10%, 15%, and 20%(wt) and 3 different SSA replacement amount of 0%, 10%, and 20%(wt) were prepared and then a series of tests and analysis were conducted to investigate how the two materials affect the quality of the final product and to what extent. It concludes that a mix with up to 20% of SSA and 5% of MIBA could result in quality tiles complying with specifications for interior or exterior flooring applications at certain kiln temperatures.

Burn-induced cardiac dysfunction is thought to involve mitochondrial dysfunction although the mechanisms responsible are unclear. In this study, we used our established model of in vivo burn injury to understand the genetic evidence of burn-induced mitochondrial metabolism confusion by describing cardiac mitochondrial metabolism-related gene expression after burn. Cardiac tissue was collected at 24 hours after burn injury. An O2K respirometer system was utilized to measure cardiac mitochondrial function. Oxidative phosphorylation complex activities were determined using enzyme activity assays. RT Profiler PCR array was used to identify differential regulation of genes involved in mitochondrial biogenesis and metabolism. Quantitative qPCR and Western Blotting were applied to validate differentially expressed genes. Burn-induced cardiac mitochondrial dysfunction was supported by the finding of decreased state 3 respiration and decreased mitochondrial electron transport chain activity in complex I, III, IV, and V following burn injury. Eighty-four mitochondrial metabolism-related gene profiles were measured. The mitochondrial gene profile showed that one third of genes related to mitochondrial energy and metabolism was differentially expressed. Of these 28 genes, 15 were more than 2-fold upregulated and 13 were more than 2-fold downregulated. All genes were validated using qPCR; 4 genes had a protein level which correlated with the observed change in gene expression. This study provides preliminary evidence that a large percentage of mitochondrial metabolism-related genes in cardiomyocytes were significantly affected by burn injury.

The aim of the present study was to assess the efficacy of All Cosmos Industries (ACI) bio-organic and bio-chemical fertilizers and ACI N-Fixer (N-Bio Booster) on the paddy yields based on the field trial plots at Langkat, Medan, Indonesia. This application of ACI bio-organic fertilizer (NPK 5/5/5) and ACI bio-chemical (NPK 15/15/15) fertilizer and ACI N-Fixer tests were conducted at the paddy farm at Langkat from May-October 2018. This study employed a factorial randomized complete block design which consisted of two factors, namely: Factor I with four types of fertilizers while Factor II consisted of two paddy varieties (Inpari 30 and Inpari 32). Overall, the filled grains in the ACI treatments are significantly (P< 0.05) higher than those in the control treatments that used Normal Chemical Compound NPK. Overall, total weight per meter² (368-617g) in ACI treatments are also significantly (P< 0.05) higher than those (319-371g) in the control treatments. At harvesting time at 105 days after transplanting, significantly higher (P< 0.05) colony counts (13-15 x 10⁶ CFU/mL) (for ACI treatments), than those (8 x 10⁶ CFU/mL) in the controls positively indicated higher total yields of paddy grains per hectare. It was found that the application of ACI bio-organic and bio-chemical fertilizers and ACI N-Fixer can improve paddy yields of the two rice varieties, between 16.4-38.2% (up to 5.75 MT/ha), in the field trial plots at Langkat. These commercial fertilizers play an imperative role in refining the soil fertility and thereby can increase the yield of rice production. Therefore, it is highly recommended that ACI bio-organic and ACI bio-chemical fertilizers and ACI N-Fixer (N-Bio Booster) can be employed to increase the paddy yield in this region.

In Taiwan, colorectal cancer is ranked second and third in terms of mortality and cancer incidence, respectively. In addition, medical expenditures related to colorectal cancer are considered to be the third highest. While advances in treatment strategies have provided cancer patients with longer survival, potentially harmful second primary cancers can occur. Therefore, second primary colorectal cancer analysis is an important issue with regard to clinical management. In this study, a novel predictive scheme was developed for predicting the risk factors associated with second colorectal cancer in patients with colorectal cancer by integrating five data mining classification techniques, including support vector machine, random forest, multivariate adaptive regression splines, extreme learning machine, and extreme gradient boosting. In total, 4,287 patients in the datasets provided by three hospital tumor registries were used. Our empirical results revealed that this proposed predictive scheme provided promising classification results and the identification of important risk factors for predicting second colorectal cancer based on accuracy, sensitivity, specificity, and area under the curve metrics. Collectively, our clinical findings suggested that the most important risk factors were the combined stage, age at diagnosis, BMI, surgical margins of the primary site, tumor size, sex, regional lymph nodes positive, grade/differentiation, primary site, and drinking behavior. Accordingly, these risk factors should be monitored for the early detection of second primary tumors in order to improve treatment and intervention strategies.

Due to the rapid development and popularity of the Internet, cloud computing has become an indispensable application service. However, how to assign various tasks to the appropriate service nodes is an important issue. Based on the reason above, an efficient scheduling algorithm is necessary to enhance the performance of system. Therefore, a Three-Layer Cloud Dispatching (TLCD) architecture is proposed to enhance the performance of task scheduling. In first layer, the tasks need to be distinguished to different types by their characters. Subsequently, the Cluster Selection Algorithm is proposed to dispatch the task to appropriately service cluster in the secondly layer. Besides, a new scheduling algorithm is proposed to dispatch the task to a suitable server in a server cluster to improve the dispatching efficiency in the thirdly layer. Basically, the TLCD architecture can obtain better task completion time than previous works. Besides, our algorithm and can achieve load-balancing and reliability in cloud computing network.

The rapid growth rate of the elderly population is a serious current issue in most countries, affecting them economically through needed medical treatment and healthcare planning. The priority concern is how to reduce the number of elderly people requiring long-term healthcare and raise the number who are able to live independently. This study executed a behavior assessment of elderly person’s self-reported use of electric scooters and analyzed their degree of acceptance of these assisted living tools, partly through a related factor analysis of our survey instrument. We used this questionnaire survey as our research method, applying SPSS22 software for factor analysis that revealed five survey facets.

Viral infections have long been the biggest threat to human survival, and from a medical perspective, the development of noninvasive high-throughput screening methods that target the incubation period to either treat diseases or limit viral spread would be strikingly effective. Using this technology to target viral incubation periods would also be inexpensive to perform. The current study proposes to transform pulse signals into a rapid diagnostic test using “coincidence analysis” in the hope of preventing or reducing the symptoms of viral infections. The heart plays a critical role in calculating and supplying the needs of all tissues of the body. Pulse waves are pressurized signals in response to heart’s calculations and include all phases of the cardiac cycle, which maintains life and provides energy needed to perform tasks. Any small movement gives a corresponding signal to pulse waves. The current study investigated conclusive data on self-limiting infections, such as common cold. We used pulse wave, coincidence analysis technology to capture signals from individuals with common cold during the incubation period and investigated if particular characteristic signals could be applied to influenza during the incubation period. Preliminary work demonstrated that pulse waves could generate signals using this technology that would be worthwhile for future research. A small amount of analytical data from common cold existed previously. The data structure is based on the idea that a single pulse wave at differing physiological conditions would have slight modifications that would be amplified and presented by various geometrical shapes after extensive data are accumulated. These geometric shapes can then be sliced vertically or horizontally to extract data during different illness stages. The significance of these findings are impressive; from a personal or a public hygiene perspective, this analytical technology provides many benefits, such as rapid and precise decision-making that can be directly visualized or can be analyzed using software programs. Also, this technology also uses futuristic wearable technology that brings practical problem solving to physiology.

Concrete cracks and local damage can affect the bond performance between concrete and steel bars, thereby reducing the durability of reinforced concrete structures. Compared with general concrete crack repair methods, biomineralization repair not only has effective bonding capabilities but is also particularly environmentally friendly. In view of this, this study aimed to apply biomineralization technology to repair damaged fiber-reinforced lightweight aggregate concrete (LWAC). Two groups of LWAC specimens were prepared. The control group used lightweight aggregates (LWAs) without bacterial spores and nutrient sources, and the experimental group used LWAs containing bacterial spores and nutrient sources. These specimens were first subjected to compression tests and pull-out tests, respectively, and thus were damaged. After the damaged specimen healed itself in different ways for 28 days, secondary compression and pull-out tests were conducted. The self-healing method of the control group involved placing the specimens in an incubator. The experimental group was further divided into experimental group I and experimental group II. The self-healing method of experimental group I was the same as that of the control group. The self-healing method of experimental group II involved soaking the specimen in a mixed solution of urea and calcium acetate for two days, and then taking it out and placing it in an incubator for two days, with a cycle of four days. The test results showed that, compared with the control group specimens, the relative bond strength ratio of the experimental group II specimens increased by 17.9%. Moreover, the EDS and XRD analysis results confirmed that the precipitate formed at the crack was calcium carbonate, which improved the compressive strength and bond strength after self-healing. This indicates that the biomineralization maintenance method used in experimental group II is more effective.

Two austenitic stainless steel (ASS) plates, 304L and 316L, were cold-rolled (304R and 316R) with a 10 % reduction in thickness then subjected to laser welding. Cold-rolling caused a slight surface hardening and introduced residual tensile stress into the ASS plates. The susceptibility to stress corrosion cracking (SCC) of the welds (304RW and 316RW) was determined using the U-bend test pieces in a salt spray. To highlight the stress concentration at the weld’s fusion boundary (FB), the top weld reinforcement was not ground off before bending. Moreover, micro-shot peening (MSP) was performed to mitigate the SCC of the welds by imposing high residual compressive stress and forming a fine-grained structure. Cold-rolling increased the susceptibility of the 304R specimen to pitting corrosion (PTC) and intergranular (IG) microcracking. Moreover, PTC and SCC were found more often at the FBs of the 304RW. The corrosion pits of the peened 304RW (304RWSP) were finer but greater in amount than the un-peened one. The results also indicated that the 316L ASS welds with MSP was resistant to the incidence of PTC and SCC in a salt spray. The better reliability and longer service life of dry storage canister could be achieved by using 316L ASS for construction and application of MSP on it.

Due to the numerous heat sources in electronic equipment, the periodic nature of stream-wise flow occurs in a cooling channel so often, necessitating the development of an effective technique to improve the heat-cooling convection in such a situation. This paper investigates thermal convection enhancement in a heated-block duct through the periodic boundary conditions using the element-by-element (EBE) treatment in a semi-implicit projection finite element method (FEM) through preconditioned conjugate gradient (PCG) solver. This paper used the time-mean Nusselt number ratio, friction factor, and thermal performance to study how installing rectangular cylinders in the channel works with periodic boundary conditions varying Reynolds numbers (100, 175, and 250). The outcomes show that the rectangular cylinders installed stream-wise above an upstream block promote thermal convection in the heated-block duct. However, increasing the number of rectangular cylinders can raise friction factor. As a result, the case for periodic boundary conditions with a rectangular cylinder above every two blocks has the best thermal performance.

Artificial Intelligence (AI) play an important role in many fields, including medical education, practice, and research. Many medical educators started using ChatGPT at the end of 2022 for many purposes. The aim of this article was to explore the potential uses, benefits and risks of using ChatGPT in integrated pharmacotherapy of infectious disease module education. This study was an experimental study with content analysis of the potential applications of the ChatGPT model for integrated pharmacotherapy of infectious diseases module education was performed. The findings of this study shows that there are many potential uses, benefits and risks associated with the use ChatGPT. In conclusion, medical and health sciences educators can use ChatGPT as a guide in many aspects related to the integrated pharmacotherapy of infectious disease curriculum development, syllabus design, lecture notes preparation and exam preparation with caution.

Background: This retrospective study evaluates the survival effects of metronomic maintenance therapy with fluoropyrimidine in patients with stage III colorectal cancer (CRC) according to epidermal growth factor receptor (EGFR) expression. Methods: We enrolled 197 patients with stage III CRC who had undergone radical resection and FOLFOX regimen adjuvant chemotherapy. The clinicopathological features and effects of metronomic maintenance therapy on survival according to treatment group and EGFR expression were analyzed. By conducting an in vitro cell line study and in vivo study through knockdout of EGFR gene, we analyzed the capacities of cell proliferation and migration. Results: Postoperative relapse and mortality were significantly more common in the FOLFOX group. Metronomic maintenance therapy was a significantly independent predictive factor of postoperative relapse and mortality, as well as a prognostic factor of disease-free survival and overall survival. The significant differences of survival between the two groups were only observed in patients with positive EGFR expression. Conclusions: The present study suggested EGFR expression as the prognostic factor in patients with stage III CRC receiving metronomic maintenance therapy. By analyzing EGFR expression, we can identify the potential candidates with optimal survival benefit from metronomic maintenance therapy in patients with stage III CRC.

Background: This retrospective study evaluate the survival effects of metronomic maintenance therapy with fluoropyrimidine in patients with stage III colorectal cancer (CRC) according to epidermal growth factor receptor (EGFR) expression. Methods: We enrolled 197 patients with stage III CRC who had undergone radical resection and FOLFOX regimen adjuvant chemotherapy. The clinicopathological features and effects of metronomic maintenance therapy on survival according to treatment group and EGFR expression were analyzed. By conducting an in vitro cell line study and in vivo study through knockdout of EGFR gene, we analyzed the capacities of cell proliferation and migration. Results: Postoperative relapse and mortality were significantly more common in the FOLFOX group. Metronomic maintenance therapy was a significantly independent predictive factor of postoperative relapse and mortality, as well as a prognostic factor of disease-free survival and overall survival. We also demonstrated that EGFR-knockout Caco2 cells are more sensitive to the inhibition effect of fluoropyrimidine than the control those. Conclusions: The present study suggested EGFR expression as the prognostic factor in patients with stage III CRC receiving metronomic maintenance therapy. By analyzing EGFR expression and treatment strategies, we can identify the potential candidates with optimal survival benefit from metronomic maintenance therapy in patients with stage III CRC.

To obtain a better estimation frequency band for source bearing estimation, source bearing estimation experiments using an ice-mounted geophone were performed at three sites on the Arctic ice cap. By transforming to the frequency domain, errors of the bearing estimation in a number of frequency bands within 1000 Hz and the horizontal peak displacements received by the geophone in the corresponding frequency bands were obtained. After comparing the variation of errors to the peak displacements in the same frequency band, it is found that the errors are related to the peak displacements, and higher peak displacement values mean smaller errors. When the incident angle of the acoustic source and the ice thickness meet certain conditions, some modes of the Lamb waves of the ice plate are excited, the peak displacements at the same frequency band are increased, the errors of bearing estimation are reduced, and the effective frequency band for bearing estimation is broadened. These results provide some new ideas for the bearing estimation of acoustic sources beneath Arctic ice.

As major natural disasters in grassland areas, fires and dust events seriously threaten human safety, property, and animal husbandry. Furthermore, these phenomena may be mutually reinforcing, which can lead to more severe cascading disasters. However, few studies have been on the mechanisms of grassland fire and dust events disaster chain. Therefore, we selected Dornod aimag (province), a typical temperate grassland, as the study area and analyzed the spatiotemporal variation patterns of grassland fires and dust weather, as well as the effect of grassland fires on dust weather based on MCD64A1 Burnt Area data and SYNOP dust data. The mechanism of grassland fires on dust weather was further investigated using the MOD13A3 vegetation index product and ERA5 wind speed, wind direction, and precipitation data. The results revealed that grassland fires and dust weather varied spatially across the study area. Furthermore, grassland fires occurred mainly in spring (April to May), summer (June), and autumn (October), while dust weather mainly occurred in spring (March to May). Moreover, autumn, winter, and spring cumulative grassland fires (both days and area) substantially affected the spring total dust weather days and dust storm days, particularly the spring cumulative dust storm days. Additionally, higher precipitation in the summer of 2014 resulted in higher vegetation coverage and more fuel in the autumn and winter of 2014, and even in the spring of 2015. As a result, the cumulative grassland fire days was higher, and the area was larger from September 2014 to April 2015, leading to a considerable increase in the cumulative dust storm days in May 2015. This study has important implications for disaster prevention and mitigation, ecological and environmental protection, and sustainable development in grasslands.

Purpose: This study builds upon an established effective training method to investigate the advantages of high variability phonetic identification training for enhancing lexical tone perception and production in Mandarin-speaking pediatric cochlear implant (CI) recipients, who typically face ongoing challenges in these areas. Method: Thirty two Mandarin-speaking children with CIs were quasi-randomly assigned into the training group (TG) and the control group (CG). The sixteen TG participants received five sessions of high variability phonetic training (HVPT) within a period of three weeks. The CG participants did not receive the training. Perception and production of Mandarin tones were administered before (pretest) and immediately after (posttest) the completion of HVPT via lexical tone recognition task and picture naming task. Both groups participated in the identical pretest and posttest with the same time frame between the two test sessions. Results: TG showed significant improvement from pretest to posttest in identifying Mandarin tones for both trained and untrained speech stimuli. Moreover, perceptual learning of HVPT facilitated trainees’ lexical tone production as rated by a cohort of 10 Mandarin-speaking adults with normal hearing. In contrast, CG did not exhibit significant changes in either perception or production. Conclusion: The results represent initial evidence of HVPT-induced transfer of perceptual learning to lexical tone production in CI users, which supports the application of this speech training protocol to aural rehabilitation practice.

Plant-derived diterpene synthases (PdiTPSs) play a critical role in the formation of structurally and functionally diverse diterpenoids. However, the specificity or promiscuity of PdiTPSs remains unclear. In order to gain more understanding of this, the sequences of 199 functionally characterized PdiTPSs and their corresponding 3D structures were collected and manually corrected. Then, the correlations among sequences, domains, structures and their corresponding products were comprehensively analyzed. However, those features alone was insufficient for ef-fective product-specific classification of PdiTPSs as these methods could not establish a clear mapping between the enzymes and products. Nevertheless, local structural analysis can identify residues that have been experimentally proven to influence product outcomes through mutagenesis, and these residues exhibit conservation in spatial positioning and physicochemical properties. And aromatic residues surrounding the substrate exhibited selectivity towards its chemical structure. Specifically, tryptophan (W) was preferentially located around the linear substrate geranylgeranyl pyrophosphate (GGPP), while phenylalanine (F) and tyrosine (Y) were preferentially located around the initial cyclized diterpene intermediate. This analysis revealed the functional space of residues surrounding the substrate of PdiTPSs, most of which have not been experimentally explored. These findings provide guidance for screening specific residues for mutation studies to change the catalytic products of PdiTPSs.

The Shitouping pluton in Jiangxi Province, southern China, hosts an ion-adsorption heave rare earth element (HREE) deposit identified by recently geological survey. This study reveals the HREE pre-enrichment mechanism during the magma-hydrothermal process of granitic bedrock based on the comprehensive study of zircon structure and composition. Zircon from the Shitouping pluton, composed of syenogranite and monzogranite, can be categorized into three types based on structure and compositions. The Type-1 zircons, the predominate type in monzogranite granite, are early magmatic zircons with prismatic crystals and bright oscillatory zoning. In contrast, the late magmatic-hydrothermal zircons (Type-2 and Type-3) are mainly occurred in the syenogranite. The Type-2 zircons occur as murky euhedral crystals crystallized in the late magmatic stage. The Type-3 zircons with irregular zoning and abundant mineral inclu-sions in BSE images are closely associated with Type-2 zircons, possibly formed via intense hy-drothermal alteration during the hydrothermal stage. The increase in Y/Ho ratios from Type-1 to Type-3 zircon indicates that the Shitouping syenogranites underwent magmatic to hydrothermal evolution. Compared with Type-1 and Type-2 zircons, Type-3 zircons exhibit the highest con-centrations of F and HREEs. The significant increase of HREE concentrations both in zircons and bulk-rock composition of syenogranite can be attributed to the introduction of HREE-rich fluids during magma evolution. Under this condition, the HREEs mainly hosted in fluorocarbonates, which can easily release HREE3+ to generate ion-adsorption deposits during the weathering process. Therefore, we propose that increase of HREE contents in zircon reflect the exsolution of HREE-rich fluids during the magma evolution, which is important factor controlling HREE en-richment in Shitouping syenogranites and further generation of ion-adsorption HREE deposits.

Reconstruction of acoustic relaxation absorption curve is a powerful approach to ultrasonic gas sensing, but requires known of a series ultrasonic absorption at various frequencies around effective relaxation frequency. Ultrasonic transducer is a most widely deployed sensor for ultrasonic wave propagation measurement and works only at a fixed frequency or specific environment like water, so a large number of ultrasonic transducers operating at various frequencies are required to recover an acoustic absorption curve with a relative large bandwidth, which cannot suit for large-scale practical applications. This paper proposes a wideband ultrasonic sensor using a distributed Bragg reflector (DBR) fiber laser for gas concentration detection through acoustic relaxation absorption curve reconstruction. With a relative wide and flat frequency response, the DBR fiber laser sensor measures and restores a full acoustic relaxation absorption spectrum of CO2 using a decompression gas chamber between 0.1 and 1 atm to accommodate the main molecular relaxation processes, and interrogates with a non-equilibrium Mach-Zehnder (M-Z) interferometer to gain a sound pressure sensitivity of -45.4 dB. The measurement error of the acoustic relaxation absorption spectrum is less than 1.32%.

Antibiotic resistance (ABR) is concerning issue due to its direct and indirect repercusions on public health, since decreased therapeutic effect of certain antibiotic to treatment complications that can cause death. There are several mechanism as to how ABR can be transferred from one microoorganisms to another, and many of them are dependant many environmental factors. The food supply chain is a environment in which ABR gene transfer can occur is multiple pathways, which generate concerns regarding food safety. Here, we summarize relevant mechanisms which are implied in ABR in food supply chain but also we are addressing routes of transmission and prevalence of ABR, implications on public health, and the application of new alternatives to antibiotics such as antimicrobial peptides, mainly bacteriocins, in order to countermeasure ABR.

Formaldehyde (HCHO) is one of the most important carcinogenic air contaminants. However, the lack of global surface concentration of HCHO monitoring is currently hindering research on outdoor HCHO pollution. Traditional methods are either restricted to small areas or data- demanding for a global scale of research. To alleviate this issue, we adopted neural networks to estimate surface HCHO concentration with confidence intervals in 2019, where HCHO vertical column density data from TROPOMI, in-situ data from HAPs (harmful air pollutants) monitoring network and ATom mission are utilized. Our result shows that the global surface HCHO average concentration is 2.30 μg/m3. Furthermore, in terms of regions, the concentration in Amazon Basin, Northern China, South-east Asia, Bay of Bengal, Central and Western Africa are among the highest. The results from our study provides a first dataset of the global surface HCHO concentration. In addition, the derived confidence interval of surface HCHO concentration adds an extra layer for the confidence to our results. As a pioneer work in adopting confidence interval estimation into AI-driven atmospheric pollutant research and the first global HCHO surface distribution dataset, our paper will pave the way for the rigorous study on global ambient HCHO health risk and economic loss, thus providing a basis for pollutant controlling policies worldwide.

Wetlands, which is composed of soil, vegetation and water, has sufficient water supply and is sensitive to climate change. This study analyzed the coupling degree between wetlands and atmosphere, and discussed the influence of environmental factors (solar radiation and water vapor pressure deficit) on latent heat flux by using the experimental data from the Maduo Observatory of Climate and Environment of the Northwest Institute of Eco-Environment and Resource, CAS and WRF model. The results showed, during the vegetation growthing season, the average value of Ω (decoupling factor) is 0.38 in alpine wetlands, indicating the coupling between wetlands and atmosphere is poor; Solar radiation is the main factor influencing the latent heat flux in the results of both observation data analysis and model simulation, and solar radiation and water vapor pressure deficit still have an opposite reaction to latent heat flux; when solar radiation and water vapor pressure deficit increase by 30%, the average daily amount of latent heat flux increases from 5.57 MJ·m-2 to 7.50 MJ·m-2 and decreases to 5.17 MJ·m-2, respectively. This study provides a new research approach for the study of the parameterization of latent heat flux and evapotranspiration under the context of global climate change.

As development progresses, when the bottom hole flowing pressure or formation pressure is less than the saturation pressure of crude oil in the reservoir, oil and gas two-phase seepage occurs in the reservoir. Due to the characteristics of oil and gas two-phase seepage, after the oil and gas two-phase seepage occurs in the reservoir, the well production will be reduced, or even greatly reduced. Therefore, how to predict the horizontal well capacity better in this case is an important problem that needs to be solved urgently. In this paper, the method and process of establishing the transient calculation model of two-phase flow in horizontal wells are introduced in detail from three aspects: fluid physical properties, reservoir oil-gas two-phase seepage, and the coupling model of Inflow Performance and Flow in Wellbore. The model is more reliable through the verification of production data from five wells in two oilfields.

The prediction of drug-target interactions plays a fundamental role in facilitating drug discovery, where the goal is to find prospective drug candidates. With the increase in the number of drug-protein interactions, machine learning techniques, especially deep learning methods, have become applicable for drug-target interaction discovery because they significantly reduce the required experimental workload. In this paper, we present a spontaneous formulation of the drug-target interaction prediction problem as an instance of multi-instance learning. We address the problem in three stages, first organizing given drug and target sequences into instances via a private-public mechanism, then identifying the predicted scores of all instances in the same bag, and finally combining all the predicted scores as the output prediction. A comprehensive evaluation demonstrates that the proposed method outperforms other state-of-the-art methods on three benchmark datasets.

Active films based on carboxymethyl chitosan incorporated corn peptide were developed. Physicochemical properties of the films, including thickness, opacity, moisture content, color, mechanical properties, water vapor permeability, and oil resistance, were measured. Biological activities of the films, including the antioxidant and antibacterial activities, were characterized in terms of 2, 2-diphenyl-1-picrylhydrazyl free radical scavenging activity, reducing power, the total antioxidant activity, and the filter disc inhibition zone method. The results indicated that the incorporation of corn peptide caused interactions between carboxymethyl chitosan and corn peptide in Maillard reaction and gave rise to the films light yellow appearance. Compared with the Control, the degree of glycosylation, browning intensity, thickness, opacity, tensile strength, antioxidant activity, and antibacterial activity of films were increased, but the elongation, vapor permeability, and oil resistance of films were decreased. The films based on corn peptide and carboxymethyl chitosan can potentially be applied to food packaging.

This study was conducted to determine the dynamic effects of dietary crude protein (CP) intake on nitrogen (N) balance, ileal amino acid digestibility, and gene expression levels of digestive enzymes at three stages in pigs. In Experiment 1, 18 growing pigs (average body weight (BW) = 9.5 kg) were randomly assigned to one of three treatments (n = 6/treatment group), including normal (20% CP), low (17% CP), and very low (14% CP) protein intake. In Experiment 2, 18 growing pigs (average BW = 30 kg) were allotted randomly to one of three treatments (n = 6/treatment group), including normal (18% CP), low (15% CP), and very low (12% CP) protein intake. In Experiment 3, 18 growing pigs (average BW = 45 kg) were assigned randomly to one of three treatments (n = 6/treatment group), including normal (16% CP), low (13% CP), and very low (10% CP) protein intake. Growing pigs fed the 14% CP and 17% CP diets had lower final BW (P < 0.05) and average daily gain (ADG) (P < 0.05) compared to pigs fed the 20% CP diet. Reducing the dietary CP level from 20 to 14% decreased urinary N excretion by 52.8% (P < 0.001) in Experiment 1. Reducing the dietary CP level from 18 to 12% decreased urinary N excretion by 55.3% (P < 0.001) and reduced fecal N excretion by 34% (P < 0.05) in Experiment 2. Reducing the dietary CP level from 16 to 10% decreased urinary N excretion by 56.4% (P < 0.001) and fecal N excretion by 47.1% (P < 0.001) in Experiment 3. Pigs fed the very low (14%, 12%, and 10% CP) diets showed higher digestibility for CP (P < 0.05), His (P < 0.05), Ile (P < 0.05), Phe (P < 0.05), Thr (P < 0.05), Trp (P < 0.05), Glu (P < 0.05), and Ser (P < 0.05) compared to pigs fed the normal (20%, 18%, and 16% CP) diets among the three experiments. Pigs fed the very low (14%, 12%, and 10% CP) diets showed higher mRNA levels for chymotrypsin C (P < 0.01 in Experiment 1 and 2; P < 0.05 in Experiment 3) compared to pigs fed the normal (20%, 18%, and 16% CP) diets among the three experiments. These results indicated that a reduction in dietary CP by 6% limited the growth performance of growing pigs, and a reduction of dietary CP by 3% supplemented with essential amino acids could reduce the excretion of N into the environment without affecting weight gain.

Canine atopic dermatitis (CAD) is a common chronic allergic skin disease. In our previous study, we isolated two probiotic strains, Lactococcus cremoris subsp. cremoris MP01 and Lacticaseibacillus paracasei subsp. paracasei MP02, from Mongolian fermented milk. These strains demonstrated potential in alleviating symptoms similar to AD and reducing specific immunoglobulin E (IgE) levels in a mouse model of AD. Building upon this discovery, our current investigation sought to evaluate the therapeutic potential of these probiotics for treating CAD. We conducted an open-label, single-arm clinical trial where dogs diagnosed with AD were administered LCP capsules containing Lc. cremoris subsp. cremoris MP01 and L. paracasei subsp. paracasei MP02 once daily for 60 days. Stool, skin swab, and venous blood specimens were collected at three intervals: before, and after 30 and 60 days of LCP intervention. The skin and fecal microbiomes were analyzed using full-length 16S rRNA sequencing. After 60 days of LCP intervention, notable improvements were observed in skin lesions and scratching behaviors, accompanied by reductions in both the Canine Atopic Dermatitis Extent and Severity Index (CADESI) and the Pruritus Visual Analogue Scale (PVAS) scores. Additionally, LCP intervention resulted in significant reductions in IgE levels and modulation in type 1 T helper (Th1)/ type 2 T helper cells (Th2)-related cytokine secretion. Microbiota analysis unveiled changes in the composition of both skin and gut microbiotas, including reductions in Shigella flexneri on the skin and Romboutsia in the gut. Levels of short-chain fatty acid (SCFA) increased following the 60-days of LCP intervention. These effects were likely mediated by alterations in gut microbiota and the upregulation of SCFA levels, which subsequently reduced the secretion of allergy-related IgE. Collectively, these mechanisms contributed to alleviating CAD symptoms, regulating skin microbiota composition, and reducing the adherence and invasion of environmental microbes and pathogens. Overall, our findings highlight the promising therapeutic potential of the Lc. cremoris subsp. cremoris MP01 and L. paracasei subsp. paracasei MP02 mixture as an effective strategy for managing CAD in dogs.

Three new polyketides (penidihydrocitrinins A–C, 1–3) and 14 known compounds (4–17) were isolated from the deep-sea-derived Penicillium citrinum W17. Their structures were elucidated by comprehensive analyses of 1D and 2D NMR, HRESIMS, and ECD calculations. Compounds 1–17 were evaluated for their anti-inflammatory and anti-osteoporotic bioactivities. All isolates exhibited significant inhibitory effects on microglial activation in LPS-stimulated BV-2 cells in a dose-response manner. Notably, compound 14 displayed the strongest effect with the IC50 value of 4.7 µM. Moreover, compounds 6, 7, and 8 not only suppressed osteoclastogenesis, but also promoted osteoblast mineralization.

Potato tubers are susceptible to wounding during post-harvest processes, leading to quality decline, perishability and large economic losses. In this study, the potato cultivar, ‘Longshu No.7’, was foliar-sprayed with 3% chitosan (w/v) three times during the pre-harvest period after flowering to evaluate the effect of foliar spraying with chitosan on suberization processing at wounds of harvested potato tubers. Our results demonstrate that foliar-sprayed with chitosan significantly reduced wound-induced fresh weight loss and dry rot disease index by 37.34% and 41.60% on the 28 day after wounding, respectively. Foliar-sprayed with chitosan accelerated the deposition of suberin polyphenolics and lignin at the wound sites of potato tubers with the formation of thicker cell layers. This occurred with increased localized activities of key enzymes in the suberin polyphenolics and lignin pathways, including phenylalanine ammonia lyase, 4-coumaryl-coenzyme A ligase, cinnamyl alcohol dehydrogenase and peroxidase (33.90–64.32%), as well as the contents of cinnamic acid, sinapic acid, flavonoids, lignins and total phenolics (19.70–23.46%) at wound sites of potato tubers on the 7 day after wounding. Our results indicated that foliar application of chitosan accelerated wound-induced suberization of potato tubers and could mitigate post-harvest product damages.

Breast cancer is the most common malignancies in women and the second leading cause of cancer death in women. Triple negative breast cancer (TNBC) subtype is a breast cancer subset without ER, PR and HER2 expression, limiting treatment options and presenting a poorer survival rate. Thus, we investigated whether HDACi would be used as potential anti-cancer therapy on breast cancer cells. In this study, we found TNBC and HER2-enrich breast cancers are extremely sensitive to Panobinostat, Belinostat of HDACi via experiments of cell viability assay, apoptotic marker identification and flow cytometry measurement. On the other hand, we developed a bioluminescence based live cell non-invasive apoptosis detection sensor (IADS) detection system to evaluate the quantitative and kinetic analyses of apoptotic cell death by HDAC treatment on breast cancer cells. In addition, the use of HDACi may also be accompanied with chemotherapeutic agent such as doxorubicin to synergic drug sensitivity on TNBC cell (MDA-MB-231), but not in breast normal epithelia cells (MCF-10A), providing therapeutic benefits against breast tumor in clinic.

Abstract：The brain often switches freely between focused attention and divergent thinking, and the default mode network (DMN) is activated during brain rest. The discovery, function and characteristics of default mode network all indicate that learning does not stop when the brain "rests". Mental disease can lead to dysfunctional default mode networks, which affects learning adversely. Therefore, default mode network plays an important role in learning. Neural activities such as β-wave rhythm regulation, "subconscious" divergence mode initiation, hippocampal function and neural replay occur during default mode, which also explain that "rest" promotes learning. This paper reveals the role and neural mechanism of default mode network in learning from the neural level, discusses the essential role default mode network plays in learning, and default mode network enables rest to promote learning.

Major depressive disorder (MDD) is a serious mental illness with a heavy social burden, but its underlying molecular mechanisms remain unclear. Mass spectrometry (MS)-based metabolomics is providing new insights into the heterogeneous pathophysiology, diagnosis, treatment, and prognosis of MDD by revealing multi-parametric biomarker signatures at the metabolite level. In this comprehensive review, recent developments of MS-based metabolomics in MDD research are summarized from the perspective of analytical platforms (liquid chromatography-MS, gas chromatography-MS, supercritical fluid chromatography-MS, etc.), strategies (untargeted, targeted, and pseudotargeted metabolomics), key metabolite changes (monoamine neurotransmitters, amino acids, lipids, etc.), and antidepressant treatments (both western and traditional Chinese medicines). Depression sub-phenotypes, comorbid depression, and multi-omics approaches are also highlighted to stimulate further advances in MS-based metabolomics in the field of MDD research.

The oscillation of an elastically mounted rigid cylinder excited by steady fluid flow is investigated. Regarding the nonlinearity of real practical structures like marine risers and the stay cable of a long-span bridge, the dynamic behavior of the circular cylinder is described by double Duffing equations and the aerodynamic force performance of the wake flow is expressed by wake oscillator equation. Unlike previous studies, in the present investigation, attention is focused on coupling the wake oscillator equations, taking into account quadratic terms. Following this approach, the cylinder's combined cross-flow and in-line Vortex-Induced Vibrations (VIV) are modeled more accurately. Empirical coefficients are adjusted through comparison with previous credible experimental studies and the effects of changing coefficients of the quadratic terms on major VIV parameters are investigated. The oscillating amplitude calculated by the present model is close to that of the experiment. The relative error of results obtained by the present coupled model is lower than the previous model. Moreover, the present model successfully predicts the moving trajectories of a circular cylinder under VIV in a figure-of-eight shape.

Rhododendron is well-known for the colorful corolla. Molecular marker systems have the potentials to elucidate genetic diversity as well as to assess the genetic fidelity in rhododendrons. In the present study, the reverse transcription domains of long terminal repeat retrotransposons were cloned from rhododendrons and used to develop inter-retrotransposon amplified polymorphism (IRAP) marker system. Subsequently, 198 polymorphic loci were generated from the IRAP and inter-simple sequence repeat (ISSR) markers, of which 119 were derived from the IRAP markers. It was justified that in rhododendrons, IRAP markers were superior to the ISSRs in some polymorphic parameters such as the average number of polymorphic loci (14.88 versus 13.17). In comparison with the single one, the combination of IRAPs and ISSRs systems was more discriminative for detecting 46 rhododendron accessions. Further, IRAP markers demonstrated more efficiency in genetic fidelity detection of in vitro R. bailiens, an endangered species just recorded in Guizhzhou Province, China. The available evidences revealed the distinct properties of IRAP and ISSR markers in the rhododendron-associated applications, and highlighted the availability of highly informative ISSR and IRAP markers in the genetic diversity evaluation and the genetic fidelity assessment of rhododendrons, which may facilitate the preservation and genetic breeding in rhododendron plants.

This work focuses on addressing the dynamic positioning and trajectory tracking problem for a 4 degree-of-freedom (DOF) unmanned underwater vehicle (UUV) in the presence of nonlinear dynamics, parametric uncertainties, system constraints, and time-varying external disturbances. To tackle this problem, a disturbance observer-based control (DOBC) scheme is proposed. The scheme is structured around the model predictive control (MPC) method integrated with an extended active observer (EAOB). Compared to the conventional disturbance observer, the EAOB has the unique ability to handle both external disturbances and system/measurement noises simultaneously. The EAOB leverages a combination of sensor measurements and a system dynamic model to estimate disturbances in real-time, which allows continuous estimation and compensation of time-varying disturbances back to the controller. The proposed disturbance observer-based MPC (DOBMPC) is implemented by feeding the estimated disturbances back into the MPC’s prediction model, which forms a robust adaptive controller with a parameter-varying model. The proposed control strategy is validated through simulations in a Gazebo and Robot Operating System (ROS) environment. The results show that it can effectively reject unpredictable disturbances and improve the UUV’s control performance.

TiC particles were prepared from Ti and C powders, and TiC-reinforced Cu-based composites were prepared by powder metallurgy with SPS sintering. The effects of SPS sintering temperature and TiC particle reinforcement phase content on the electrical and mechanical properties of Cu-based composites were investigated. The reinforcement of TiC particles by thermal mismatching at increasing sintering temperature has a significant strengthening effect on the composites, but the high temperature causes softening of the Cu matrix and the growth of grains reduces the properties of the composites. In this study, the effects of porosity and density on the composite properties were not significant.

Examining the clustering characteristics and fluctuations within urban areas during peak hours through the lens of bike-sharing is of utmost importance in the optimization of bike-sharing systems and urban transportation planning. This investigation adopts the principles of urban spatial interaction network construction and employs streets as the fundamental units of analysis to model bike-sharing activities during morning and evening peak hours within Beijing's six central districts. Subsequent to this, a comprehensive analysis of the network's structural attributes was carried out. A walktrap method rooted in modularity analysis was introduced to discern and scrutinize the clustering patterns and characteristics of communities within the network across different temporal intervals. Empirical findings reveal a predominant usage pattern of shared bicycles for short-distance travel during both morning and evening peak hours. Notably, distinctive community structures manifest during these periods, characterized by two large communities and multiple smaller ones during the morning peak, while the evening peak showcases a single large community alongside several medium-sized and smaller ones. Moreover, the extended interaction radius points to an expanded geographic range of interactions among streets. These findings bear significant implications for the management of urban transportation, bike-sharing enterprises, and urban residents, proffering valuable insights for the optimization of bike-sharing schemes and transportation strategies.

Synthetic Aperture Radar (SAR) is an active sensor that uses microwave for sense, it is unrestricted by weather and illumination conditions, and it can observe targets all day and weather. Aircraft targets are important monitoring objects in military and civilian fields, and how to efficiently detect and recognize aircraft targets is an important topic in the field of SAR image interpretation. Based on the features of SAR images, such as complex background, high resolution, and multi-scale, we proposed an improved method based on YOLOv5s. Firstly, this paper proposed the structure of the multi-scale receptive field and channel attention fusion, which is applied to the shallow layer of the backbone of YOLOv5s, it can adjust the weights of the multi-scale receptive field during the training process to enhance the extraction ability of feature information. Secondly, we proposed four de-coupled detection heads to replace the original part in YOLOv5s, which can improve the efficiency and accuracy of SAR image interpretation for small targets. Thirdly, in the case of the limited amount of SAR images, this paper proposed multi methods of data augmentation, which can enhance the diversity and generalization of the network. Fourthly, this paper proposed the K-means++ to re-place the original K-means to improve the network convergence speed and detection accuracy. Finally, Experiments demonstrate that the improved YOLOv5s can enhance the accuracy of SAR image interpretation by 9.3%, and the accuracy of small targets is improved more obviously, reaching 13.1%.

The cutter structure and layout scheme of PDC (Polycrystalline Diamond Compact) bits are important factors in improving efficiency. To further improve the drilling efficiency of PDC bits, axe, triangular prism, and cylindrical PDC cutters were used as research objects. Based on the measured granite data, a finite element model of non-homogeneous granite was established and verified by uniaxial compression simulation. The rock-breaking process of different cutter combination schemes was compared using the finite element method, and the parameters in the best scheme were optimized using the Box-Behnken response surface method. The results show that the constructed model of non-homogeneous granite is consistent with the stress-strain relationship of real granite and is reliable. The axe PDC cutter is more aggressive than the other two cutters and is more suitable for the front row of the bit blade tooth arrangement, while the triangular prism cutter is the second most aggressive and is suitable for the rear row of tooth arrangement, and the best combination scheme is the front row of axe cutter and the rear row of triangular prism cutter arranged alternately with the axe cutter. The optimal transverse and longitudinal distances of the optimized triangular prism cutter from the front axe cutter are 10mm and 7mm, and the optimal transverse and longitudinal distances of the rear axe cutter from the front cutter are 10.06mm and 7mm. The drilling speed is more stable during drilling and the PDC bit with mixed tooth arrangement has 16.8% and 16.6% higher rate of penetration(ROP) compared with the bit with single axe cutter and triangular prism cutter, and the drilling speed is more stable during working, which can effectively improve the rock breaking efficiency of the PDC bit. The field application proves that the bit with mixed cutter arrangement is easier to break the complex formations, with more stable ROP and better efficiency. The study can provide theoretical support for the cutter layout of the PDC bit.

Conducted within the scope of geochemical exploration in Eastern Thailand, this study aims to detect geochemical anomalies and potential mineral deposits. The objective was to interpret intricate spatial dispersion patterns and concentration levels of deposit pathfinder elements, specifically arsenic (As), copper (Cu), and zinc (Zn), using a comprehensive array of stream sediment geochemistry data. Methodologies involved integrating multifractal properties and traditional statistics, facilitated by the GeoDAS and ArcGIS platforms as instrumental analytical tools. In total, 5,376 stream sediment samples were collected and evaluated, leading to the development of an in-depth geochemical map. The results indicated distinct geological units marked by substantially elevated average values of the aforementioned elements. Identification of geochemical anomalies was achieved through the spatial distribution method and the subsequent application of the Spectrum-Area (S-A) multifractal model. An intriguing link was found between high As concentrations and gold deposits in the area, suggesting As as a viable pathfinder element for gold mineralization. The anomaly maps, generated from the stream sediment data, spotlighted potential zones of interest, offering valuable guidance for future mineral exploration and geological inquiries. Nonetheless, it is vital to recognize that the increased values noted in these maps may be influenced by regional geological factors, emphasizing the necessity for a diverse set of analytical methods for accurate interpretation. The study's significance lies in its pioneering use of the S-A multifractal model in geochemical data analysis. This innovative approach has deepened our comprehension of geochemical dispersion patterns and improved the precision of mineral exploration.

This study used a two-stage network data envelopment analysis model to measure the water use efficiency of 108 cities in the Yangtze River Economic Belt in the initial water use and wastewater treatment phases from 2009 to 2019. We used the Dagum Gini coefficient to decompose the urban water use efficiency of six major urban clusters in the Yangtze River Economic Belt. We also used σ convergence and β convergence types to test the convergence characteristics of urban water use efficiency of six major urban clusters in the Yangtze River Economic Belt. This study found that the overall low level of water use efficiency in cities in the Yangtze River Economic Zone mainly stems from the low level of water use efficiency in the wastewater treatment stage. The 108 cities in the Yangtze River Economic Zone are divided into four types based on the average values of water use efficiency in the initial use and wastewater treatment phases; the highest number of cities are in the double-low category, with low average values of water use efficiency in the initial use and wastewater treatment phases. During the study period, spatial differences in urban water use efficiency in the Yangtze River Economic Zone narrowed, with the differences stemming mainly from hyperdensity, followed by intra- and inter-regional differences. Meanwhile, there is convergence in urban water use efficiency in the Yangtze River Economic Belt; significant β convergence in the urban agglomerations of the Yangtze River Delta, Jianghuai, middle reaches of the Yangtze River, Chengdu–Chongqing, and Central Yunnan; and insignificant β convergence in the Central Qian urban agglomeration. After considering control factors, such as industrial structure, financial development level, environmental regulation, economic development level, and science and education development level, the water use efficiency of the six major urban clusters in the Yangtze River Economic Belt converges faster, but the influence of these control factors on the water use efficiency of each urban cluster is heterogeneous. Research results have reference value for the development of improvement strategies on differentiated urban water use efficiency in the Yangtze River Economic Belt.

Chalcones are a class of flavonoids possessing a variety of biological activities, including antimicrobial and antioxidant effects. Therefore, chalcones and their derivatives have potential use in the control of postharvest diseases. In this work, the effects of 2ʹ,4ʹ-dichloro-chalcone on the in vitro growth and in vivo pathogenicity of F. tricinctum and T. roseum were investigated. The results showed that 100 µM of 2ʹ,4ʹ-dichloro-chalcone strongly inhibited mycelial growth and conidial production of F. tricinctum (32.3%) and T. roseum (65.2%) in vitro. This treatment also significantly inhibited the expansion of potato dry rot from F. tricinctum (48.6%) and apple rot spot from T. roseum (36.2%). The incubation of F. tricinctum and T. roseum conidia with this agent for 2 h increased their cell membrane permeability by 25% and 22.5%, respectively and conidial membrane permeability by 41.7 and 65.4%, respectively. This treatment also significantly inhibited the total respiration rate and activated the cyanide-resistant respiratory pathway in both pathogens. Protein immunoblotting showed that the treatment increased alternative oxidase (AOX) levels after 4 h in F. tricinctum and T. roseum by 52.76% and 39.13%, respectively. Conclusion: 100 µM 2ʹ,4ʹ-dichloro-chalcone significantly inhibited mycelial growth and spore production in F. tricinctum and T. roseum in vitro and reduced their pathogenicity in postharvest potato and apple crops. Further analysis indicated that 2ʹ,4ʹ-dichloro-chalcone disrupted the integrity of cell membranes and the mitochondrial respiratory electron transport chain which leaded to ROS burst and oxidative stress, AOXs were induced directly or indirectly, and the cyanide resistant respiratory pathway was activated. The in vitro growth and pathogenicity of F. tricinctum and T. roseum were inhibited.

Airborne distributed position and orientation system (ADPOS), which integrates multi-inertia measurement units(IMUs), data-processing computer and Global Navigation Satellite System (GNSS), serves as a key sensor in new higher-resolution airborne remote sensing, such as array SAR, multinode imaging loads and so on. ADPOS can provide multinode high accuracy spatio-temporal reference information to realize multinode motion compensation with the various state estimation methods such as Central Difference Kalman Filtering (CDKF), modifed CDKF. However, these methods focus on noise optimization based on known nonlinear models and its linear minimum variance estimation criterion, which cannot gain better estimation performance for high-dimensional nonlinear systems. For this reason, the variational optimization process based on conjugate gradient algorithm is proposed for the estimation of filtering update step, which is more efficient than linear minimum variance estimation criterion. Therefore, aiming at ADPOS with high-dimensional and nonlinearity, Central Difference Variational Filtering (CDVF) using variational optimization based on conjugate gradient algorithm for mean correction in the filtering update stage is devoted to advancing the estimation accuracy of multinode motion parameters. A real ADPOS flight test has been conducted, the experimental results show that the accuracy of the slave motion parameters has a distinct progress than the up to date CDKF, and the compensation performance is distinct.

Density functional theory (DFT) and coupled cluster theory (CCSD(T)) calculations are performed to investigate the geometric, electronic structures and chemical bonding of a series of Cu-doped zinc oxide clusters, CunZn3O3 (n = 1-4). The structural evolution of CunZn3O3 (n = 1-4) clusters are elaborated in our work. The planar seven-membered ring of CuZn3O3 cluster plays an important role in the structural evolution, that is, the Cu atom, Cu dimer (Cu2) and Cu trimer (Cu3) anchor on the CuZn3O3 cluster. The aggregate behavior of Cu atoms on Zn3O3 may offer insight into the study of Cu/ZnO-based catalysts. Additionally, it is found that the CunZn3O3 clusters become more stable as the Cu content (n) increases. Bader charge analysis points out that as the Cu atoms doping, the reducibility of Cu aggregation (Cun-1) on the CuZn3O3 cluster increases. Combined with the d-band centers and the surface electrostatic potential (ESP), the reactivity and the possible reaction sites of CunZn3O3 (n = 1-4) clusters are also illustrated.

The bilateral trade relationship between PRC and ASEAN is close. As early as 2012, China has been the largest trading partner of ASEAN, and ASEAN has also taken the place of the United States as PRC’s second largest trading partner in 2019.This paper uses the theory of ecological population evolution, selects the total import and export volume of PRC and the ten ASEAN countries from 2000 to 2019 as the data sample, studies the bilateral trade relations between PRC and the ten ASEAN countries, analyzes the competition and symbiotic relationship of bilateral trade between PRC and the ten ASEAN countries and the possibility of trade friction according to the results, and proposes corresponding improvement strategies. According to the results of the population evolution competition model, China has a competitive relationship with Indonesia, Malaysia, the Philippines, Singapore and Thailand, which is most likely to cause trade friction. China has a biased relationship with Brunei, Cambodia, Laos, Myanmar and Vietnam, which is more likely to cause trade friction. On this basis, in order to further strengthen the trade relations between PRC and the ten ASEAN countries, this paper puts forward policy suggestions on improving infrastructure, strengthening independent innovation, seeking cooperation fields and actively investing abroad.

Conclusions: Molecular classification could provide reliable supplementary information for evaluating prognostic and contribute to treatment option decision-making in EEC patients. Fertility-sparing treatment is not recommended for EEC patients with CNH and MSI-H. Furthermore, fertility-sparing treatment can be attempted in EEC patients with CHL, but regular follow-up should be carried out to early detection of EC relapse and prevention of disease progression.

To achieve efficient utilization of low-concentration mine gas, reduce resource waste, and alleviate environmental pollution, high-temperature oxidation of low-concentration gas at a concentration range of 1.00% to 1.50% that is directly discharged into the atmosphere during coal mine production was oxidized to recover heat for reuse. The gas oxidation equipment was improved for the heating process, and the safety of low-concentration gas oxidation under high-temperature environment was evaluated. Experimental results showed that the reactor could provide a 1000 ℃ high-temperature oxidation environment for gas oxidation after installing high-temperature resistant ceramics. The pressure variation curves of the reactor with air and different concentrations of gas were similar. Due to the thermal expansion, the air pressure slightly increased and then returned to normal pressure. In contrast, the low-concentration gas exhibited a stable pressure response in the high-temperature environment of 1000 ℃. The outlet pressure was significantly greater than the inlet pressure, and the pressure difference between the inlet and outlet exhibited a trend to increase with the gas concentration. The explosion limit varied with the temperature and the blend with oxidation products. The ratio of measured gas pressure to air pressure after oxidation was below the explosion criterion, indicating that the measured concentration gas is still safe after the shift of explosion limit, which provides a safe concentration range for efficient use of low-concentration gas in the future.

To keep the global navigation satellite system functional during extreme conditions, it is a trend to employ autonomous navigation technology with inter-satellite link. As in the newly built BeiDou system (BDS-3) equipped with Ka-band inter-satellite links, every individual satellite has the ability of communicating and measuring distances among each other. The system also has less dependence on the ground stations and improved navigation performance. Because of the huge amount of measurement data, centralized data processing algorithm for orbit determination is suggested to be replaced by a distributed one in which each satellite in the constellation is required to finish a partial computation task. In current paper, the balanced extended Kalman filter algorithm for distributed orbit determination is proposed and compared with whole-constellation centralized extended Kalman filter, iterative cascade extended Kalman filter, and increasing measurement covariance extended Kalman filter. The proposed method demands a lower computation power however yields results with a relatively good accuracy.

Malaria, as a major global health problem, continues to affect a large number of people each year, especially those in the developing countries. Effective drug discovery is still one of the main efforts to control malaria. As natural products are still considered as a key source for discovery and development of therapeutic agents, we have evaluated more than 2000 plant extracts against Plasmodium falciparum. As a result, we discovered dozens of plant leads that displayed antimalarial activity. Our phytochemical study of some of these plant extracts led to identification of several potent antimalarial compounds. The prior comprehensive review article entitled “Antimalarial activity of plant metabolites” by Schwikkard and Van Heerden (2002) reported structures of plant-derived compounds with antiplasmodial activity and covered literature up to the year 2000. As a continuation of this effort, the present review covers the antimalarial compounds isolated from plants, including marine plants, reported in the literatures from 2001 to the end of 2017. During the span of the last 17 years, 175 antiplasmodial compounds were discovered from plants. These active compounds are organized in our review article according to their plant families. In addition, we also include ethnobotanical information of the antimalarial plants discussed.

With the rapid development of MEMS (Micro-electro-mechanical Systems) fabrication technologies, manifolds microelectrodes with various structures and functions have been designed and fabricated for applications in biomedical research, diagnosis and treatment through electrical stimulation and electrophysiological signal recording. The flexible MEMS microelectrodes exhibit multi-aspect excellent characteristics beyond stiff microelectrodes based on silicon or SU-8, which comprising: lighter weight, smaller volume, better conforming to neural tissue and lower fabrication cost. In this paper, we mainly reviewed key technologies on flexible MEMS microelectrodes for neural interface in recent years, including: design and fabrication technology, flexible MEMS microelectrodes with fluidic channels and electrode-tissue interface modification technology for performance improvement. Furthermore, the future directions of flexible MEMS microelectrodes for neural interface were described including transparent and stretchable microelectrodes integrated with multi-aspect functions and next-generation electrode-tissue interface modifications facilitated electrode efficacy and safety during implantation. Finally, the combinations among micro fabrication techniques with biomedical engineering and nanotechnology represented by flexible MEMS microelectrodes for neural interface will open a new gate to human lives and understanding of the world.

Pain is unpleasant sensory and emotional experience accompanied by tissue injury. Often an indi-vidual experience, it can be influenced by different physiological, psychological, and social factors. Fibromyalgia, one of the most difficult-to-treat types of pain, is characterized by general muscle pain accompanied by obesity, fatigue, sleep, and memory and psychological concerns. Fibromyal-gia has increased nociceptive sensations via central sensitization in the brain and spinal cord level. We used intermittent cold stress to create a mouse fibromyalgia pain model (Day 0: 3.69  0.14 g; Day 5: 2.13  0.12 g). Mechanical pain could be reversed by eicosapentaenoic acid (EPA) admin-istration (Day 0: 3.72  0.14 g; Day 5: 3.69  0.13 g). A similar trend could be also observed for thermal hyperalgesia. The levels of elements in the transient receptor potential V1 (TRPV1) sig-naling pathway were increased in the ascending pain pathway, including the thalamus, medial prefrontal cortex, somatosensory cortex, anterior cingulate cortex, and cerebellum. EPA intake significantly attenuated this overexpression. Novel chemogenetics method was used to indeed in-hibit SSC to ACC activity presented an analgesic effect through TRPV1 downstream pathway. The present results provide insights as to the role of TRPV1 signaling pathway as in fibromyalgia and its potential as a clinical target.

Federated learning trains a neural network model using the client's data to maintain the benefits of centralized model training, while maintaining the privacy. However, if the client data are not independently and identically distributed (non-IID) because of different environments, the accuracy of the model may suffer from client drift during training owing to discrepancies in each client's data. This study proposes a personalized federated learning algorithm based on the concept of multitask learning to divide each client model into two layers: a feature extraction layer and a category prediction layer. The feature extraction layer maps the input data to a low-dimensional feature vector space. Furthermore, the parameters of the neural network are aggregated with those of other clients using an adaptive method. The category prediction layer maps low-dimensional feature vectors to the label sample space, with its parameters remaining unaffected by other clients to maintain client uniqueness. The proposed personalized federated learning method produces faster learning model convergence rates and higher accuracy rates for the non-IID datasets in our experiments.

Neuropathic pain is initiated by a malfunction of the somatosensory cortex system. Acupuncture had been shown to have therapeutic effects for neuropathic pain, although with uncertain mechanisms. We used electroacupuncture (EA) to treat mice spared nerve injury (SNI) model and explore the underlying molecular mechanisms through novel chemogenetic techniques. Both me-chanical and thermal pain were found in SNI mice till four weeks (mechanical: 3.23 ± 0.29 g; thermal: 4.9 ± 0.14 s). Hyperalgesia was attenuated by 2 Hz EA (mechanical: 4.05 ± 0.19 g; ther-mal: 6.22 ± 0.26 s) but not with sham EA (mechanical: 3.13 ± 0.23 g; thermal: 4.58 ± 0.37 s), sug-gesting EA’s specificity. In addition, animals with transient receptor potential V1 (Trpv1) deletion showed no significant induction of neuropathic pain (mechanical: 4.43 ± 0.26 g; thermal: 6.24 ± 0.09 s). Moreover, we found increased levels of inflammatory factors such as interleukin-1 beta (IL1-β), IL-3, IL-6, IL-12, IL-17, tumor necrosis factor alpha, and interferon gamma after SNI modeling, which decreased in EA and Trpv1-/- group rather than sham group. Western blot and immunofluorescence analysis showed similar tendency in the dorsal root ganglion, spinal cord dorsal horn, somatosensory cortex (SSC), and anterior cingulate cortex (ACC). In addition, a novel chemogenetics method was used to precisely inhibit SSC to ACC activity showed an analgesic effect through TRPV1 pathway. In summary, our findings indicate a novel mechanism underlying neuropathic pain as beneficial targets for neuropathic pain.

This study aimed to investigate the efficacy of probiotics in elderly hospitalized tube-fed patients undergoing antibiotic therapy for Clostridium difficile-associated diarrhea (CDAD). Probiotics were administered to 29 patients, with twice-daily doses for 7 days following the completion of antibiotic treatment. In the probiotic group, while stool form showed no significant change, there was a significant decrease in stool frequency. Conversely, the control group exhibited improved stool form but not frequency. The probiotic group maintained a significant difference in stool form during the follow-up period. Additionally, the control group showed a positive correlation between stool form, frequency, antibiotic therapy, and intensive care unit admission, which was not observed in the probiotic group. These findings suggest that supplementing with probiotics can effectively normalize stool form in elderly hospitalized tube-fed patients undergoing antibiotic treatment for CDAD, highlighting the potential benefits of probiotic intervention in this specific population.

Cloud computing has become a widespread technology due to ICT advancements. It allows businesses to move and take advantage of the pay-as-you-go price model. Enterprises pay for what they use and don't have to buy, setup, or maintain resources. However, outsourcing core resources such as storage, servers, operating systems, and software applications from a third party needs careful decisions to take advantage of cloud facilities. Choice of appropriate service provider, deployment and service model must be aligned with business needs and goals. In this paper, we will present cloud computing benefits, cloud deployment methods, services, state-of-the-art migration methods, tools and techniques and will conclude with the role of SDN in cloud computing.

In our article in Genome Biology Ecology six years ago, one complete plastid genome of Belian was assembled for comparative analyses of the plastomes in Lauraceae. However, Ariati et al. (2023) concluded that our sequenced Belian individual could be located in the clade of Myristicaceae instead of that of Lauraceae. Here, we performed re-analyses of additional two Belian plastomes, along with 42 plastomes from plants spanning ten families of the Magnoliids. The plastomes of the three Belian individuals range from 157,535 to 157,577 bp in length. Comparative genomic analysis revealed 170 mutation sites in their plastomes, which include 111 substitutions, 53 indels, and six microinversions. Phylogeny was reconstructed using maximum likelihood and Bayesian approaches for 44 magnoliids species indicated that our three Belian individuals are nested among the species in the family Lauraceae rather than Myristicaceae.

Osteoporosis is a common problem in orthopedic medicine, and it has become an important medical issue in orthopedics as Taiwan is gradually becoming an aging society. In the diagnosis of osteoporosis, the bone mineral density (BMD) derived from dual-energy X-ray absorptiometry (DXA) is the main criterion for orthopedic diagnosis of osteoporosis, but due to the high cost of this equipment and the lower penetration rate of the equipment compared to the X-ray images, the problem of osteoporosis has not been effectively solved for many people who suffer from osteoporosis, however, at present, in clinical diagnosis, doctors are not yet able to accurately interpret X-ray images for osteoporosis manually, and must rely on the data obtained from DXA. In recent years, with the continuous development of artificial intelligence, especially in machine learning and deep learning, significant progress has been made in image recognition. Therefore, it is worthwhile to revisit whether it is possible to use a convolutional neural network model to read a hip X-ray image and then predict the patient's BMD. In this study, we proposed a hip X-ray image segmentation model and a hip X-ray image recognition classification model. First, we used the U-Net model as a framework to segment the femoral neck, greater trochanter, wards triangle, and the total hip in the hip X-ray images. We then performed image matting and data augmentation. Finally, we constructed a predictive model for osteoporosis using deep learning algorithms. In the segmentation experiments, we used intersection over union (IoU) as the evaluation metric for image segmentation, and both the U-Net and U-Net++ models achieved segmentation results greater than or equal to 0.5. In the classification experiments, using the T-score as the classification basis, the total hip using the DenseNet121 model has the highest accuracy of 74%.

The study aimed to estimate the prevalence and association between sarcopenia and blood biochemical parameters, nutritional intake, anthropometric measurements, physical performance, and physical activity in patients with Type 2 Diabetes Mellitus (T2DM). According to the diagnosis criteria of the Asian Working Group for Sarcopenia (AWGS) in 2019, 110 patients with T2DM (aged: 50–80 years) were divided into three groups: Non-sarcopenia (n = 38), Possible Sarcopenia (n = 31, 28.2%), and Sarcopenia (n = 41, 37.3%). Blood samples were collected and nutritional intake was evaluated by a registered dietitian. A food frequency questionnaire and Godin leisure-time exercise questionnaire were used to assess their daily vitamin D intake and physical activity. There were significant differences in age, serum vitamin D3 levels, nutritional intake, anthropometric measurements, and physical performance between the three groups. In elderly patients with T2DM, there was a significant association between sarcopenia with BMI, body fat percentage (BF%), and dietary energy and protein intake. Low serum vitamin D3 is a significant risk factor for possible sarcopenia.

The buildup dynamics of diode-pumped passively mode-locked solid-state laser is thoroughly explored by the real-time measurement with temporal sampling rate up to 40 GHz. A concise cavity is developed to ensure the transient dynamics purely arising from the gain medium and saturable absorber. Experimental results reveal that the laser output in the buildup process exhibits numerous passively Q-switched pulses followed with a damped relaxation oscillation prior to the stable mode locking. Furthermore, it is confirmed that the laser output has already displayed single clean mode-locked pulses inside the first several Q-switched envelopes before stepping into the stage of relaxation oscillation. The present real-time exploration is expected to provide important information for practical applications with temporal modulation of the pump intensity.

Recently, resistive random access memory (RRAM) has been an outstanding candidate among various emerging nonvolatile memories for high density storage and in-memory computing applications. However, the traditional RRAM, which accommodates two states depending on applied voltage, cannot meet the high density requirement in the era of big data. Many research groups have demonstrated that RRAM possesses the possibility of multi-level cell to overcome the demand of mass storage. Among numerous semiconductor materials, gallium oxide, as the fourth-generation semiconductor material, is highly-profile due to its excellent material proper-ties, and already be widely used in optoelectronics, high-power, resistive switching device and so on, due to its wide bandgap and transparent properties. In this study, we have successfully demonstrated the Al/GO/Ga2O3/ITO RRAM to achieve the possibility of two-bit storage. Compared to the single-layer counterpart, the bilayer structure has excellent electrical properties and stable reliability. The endurance characteristics could be enhanced above 100 switching cycles with an ON/OFF ratio of over 103. Moreover, the filament models are also described in this thesis to clarify the transport mechanisms.

In a complex working environment, the fault signal of the gearbox is greatly affected by the outside world, and fault feature recognition is difficult, so the fault diagnosis accuracy is difficult to meet the expected requirements. To solve this problem, this paper proposes a gearbox fault diagnosis method based on an optimized stacked denoising auto encoder (SDAE) and kernel extreme learning machine (KELM). Firstly, the Particle Swarm Optimization algorithm in Adaptive Weight (SAPSO) was adopted to optimize the SDAE network structure, and the number of hidden layer nodes, learning rate, noise addition ratio and iteration times were adaptively obtained to make SDAE obtain the best network structure. Then, the best SDAE network structure was used to extract the deep feature information of weak faults in the original signal. Finally, the extracted fault features are fed into KELM for fault classification. Experimental results show that, compared with existing commonly used methods of fault diagnosis, the fault diagnosis model proposed in this paper can reduce the influence of noise in the original signal can better learn the deep-level features in the original signal and has higher diagnosis accuracy, faster diagnosis speed and good generalization in fault diagnosis.

The prediction of wind power output is part of the basic work of power grid dispatching and energy distribution. At present, the output power prediction is mainly obtained by fitting and regressing the historical data. The medium- and long-term power prediction results exhibit large deviations due to the uncertainty of wind power generation. In order to meet the demand for accessing large-scale wind power into the electricity grid and to further improve the accuracy of short-term wind power prediction, it is necessary to develop models for accurate and precise short-term wind power prediction based on advanced algorithms for studying the output power of a wind power generation system. This paper summarizes the contribution of the current advanced wind power forecasting technology and delineates the key advantages and disadvantages of various wind power forecasting models. These models have different forecasting capabilities, update the weights of each model in real time, improve the comprehensive forecasting capability of the model, and have good application prospects in wind power generation forecasting. Furthermore, the case studies and examples in the literature for accurately predicting ultra-short-term and short-term wind power generation with uncertainty and randomness are reviewed and analyzed. Finally, we present prospects for future studies that can serve as useful directions for other researchers planning to conduct similar experiments and investigations.

Due to the impacts from climate change, the allocation of water resources must urgently be optimized worldwide to ensure that the needs of both water managers and farmers are balanced. In this study, manager-oriented and farmer-oriented assessment models were developed for irrigation water optimization and allocation. The distance from water sources and hydraulic head were the main factors in the manager-oriented assessment model; crop value, water demand of crops, and soil type were additional factors in the farmer-oriented assessment model. The developed assessment models were used to assess irrigation water allocation in five villages in Neimen District. Cadasters at high elevation were discovered to not be suitable for cultivation of crops because of the difficulties in constructing irrigation facilities and the loss of irrigation water during transportation. The result obtained from the manager-oriented assessment system was related to the costs involved in the construction and maintenance of irrigation facilities, which indicated that cadasters located at long distances from water sources and at high elevation are unsuitable for cultivation. By contrast, the result obtained from the farmer-oriented assessment system was related to the profits of farmers and revealed that more cadasters would be suitable for cultivation if suitable crops were chosen.

The ever-burgeoning growth of autonomous unmanned aerial vehicles (UAVs) has demonstrated a promising platform for utilization in real-world applications. In particular, UAV equipped with a vision system could be leveraged for surveillance applications. This paper proposes a learning-based UAV system for achieving autonomous surveillance, in which the UAV can be of assistance in autonomously detecting, tracking, and following a target object without human intervention. Specifically, we adopted the YOLOv4-Tiny algorithm for semantic object detection and then consolidated it with a 3D object pose estimation method and Kalman Filter to enhance the perception performance. In addition, a back-end UAV path planning for surveillance maneuver is integrated to complete the fully autonomous system. The perception module is assessed on a quadrotor UAV, while the whole system is validated through flight experiments. The experiment results verified the robustness, effectiveness, and reliability of the autonomous object tracking UAV system in performing surveillance tasks. The source code is released to the research community for future reference.

To quantify damage to reinforced concrete (RC) column members after an earthquake, an engineer needs to know the maximum applied force that was generated by the earthquake. Therefore, in this work, piezoceramic transducers are used to detect the applied force on an RC column member under dynamic loading. To investigate the use of post-embedded piezoceramic sensors in detecting the force that is applied to RC columns, eight full-size RC column specimens with various failure modes are tested under specific earthquake loadings. Post-embedded piezoceramic sensors are installed at a range of depths (70-80 mm) beneath the surface of a column specimen to examine the relationship between the signals that are obtained from them and the force applied by the dynamic actuator. The signals that are generated by the post-embedded piezoceramic sensors, which correlate with the applied force, are presented. These results indicate that the post-embedded piezoceramic sensors have great potential as tools for measuring the maximum applied force on an RC column in an earthquake. Restated, signals that are obtained from post-embedded piezoceramic sensors on an RC column in an earthquake can be used to determine the applied force and corresponding damage or residual seismic capacity.

The microsporidium Nosema ceranae is a high prevalent parasite of the European honey bee (Apis mellifera). This parasite is spreading across the world into its novel host. The developmental process and some mechanisms of N. ceranae infected honey bees has been studied thoroughly, however, few studies have been carried out in the mechanism of gene expression in N. ceranae during infection process. We therefore performed suppressive subtractive hybridization (SSH) approach to investigate the candidate genes of N. ceranae during its infection process. Each 96 clones of infected (forward) and non-infected (reverse) library were dipped onto the membrane for hybridization. A total of 118 differentially expressed sequence tags (ESTs) had been sequenced. For the host responses, 20% of ESTs (13 ESTs, 10 genes and 1 non-coding RNA) from forward library and 83% of ESTs (44 ESTs, 28 genes) from reverse library were identified as differentially expressed genes (DEGs) of the hosts. High percentage of DEGs involved in catalytic activity and metabolic processes, revealed the host gene expression change after N. ceranae infection might lead to the unbalance of physiological mechanism. Among the ESTs from forward library, 75.4% ESTs (49 ESTs belonged to 24 genes) were identified as N. ceranae genes. Of 24 N. ceranae genes, nine DEGs were subjected to real-time quantitative reverse transcription PCR (real-time qRT-PCR) for validation. The results indicated that these genes showed highly up-regulated during N. ceranae infection. Among nine N. ceranae genes, one N. ceranae gene (AAJ76_1600052943) showed the highest expression level after infection. These identified differentially expressed genes from this SSH could provide information about the pathological effects of N. ceranae. Validation of nine up-regulated N. ceranae genes revealed highly potential for the detection of early nosemosis in the field and provide insight for further applications.

The rapid development of multicopters has led to many security problems. In order to prevent multicopters from invading restricted areas or famous buildings, an Anti-UAV Defense System (AUDS) has been developed and become a research topic of interest. Topics under research in relation to this include electromagnetic interference guns for unmanned aerial vehicles (UAVs), high-energy laser guns, US military net warheads, and AUDSs with net guns. However, these AUDSs use either manual aiming or expensive radar to track UAVs. This paper proposes a dual-axis rotary platform with UAV automatic tracking. The tracking platform uses visual image processing technology to track and lock the dynamic displacement of a UAV. When a target UAV is locked, the system uses a nine-axis attitude meter and laser rangefinders to measure its flight altitude and calculates its longitude and latitude coordinates through sphere coordinates to provide UAV monitoring for further defense or attack missions. Tracking tests of UAV flights in the air were carried out using a DJI MAVIC UAV at a height of 30 meters to 100 meters. It was set up for UAV image capture and visual recognition for tracking under various weather conditions by a thermal imager and a full-color camera respectively. When there was no cloud during the daytime, the images captured by the thermal imager and full-color camera provide a high-quality image recognition result. However, under dark weather, black clouds will emit radiant energy and seriously affect the capture of images by a thermal imager. When there is no cloud at night, the thermal imager performs well in UAV image capture. When the UAV is tracked and locked, the system can effectively obtain the flight altitude and longitude and latitude coordinate values.

The increased consumption of high fat-containing foods has been linked to the prevalence of obesity and abnormal metabolic syndromes. Rhizopus oligosporus, a fungus in the family Mucoraceae, is widely used as a starter for homemade tempeh. Although R. oligosporus can prevent the growth of other microorganisms, it grows well with lactic acid bacteria (LAB). Lactobacillus plantarum can produce β-glucosidase, which catalyzes the hydrolysis of glucoside isoflavones into aglycones (with greater bioavailability). Therefore, the development of a soybean-based functional food by the co-inoculation of R. oligosporus and L. plantarum is a promising approach to increase the bioactivity of tempeh. In this study, the ameliorative effect of L. plantarum in soy tempeh on abnormal carbohydrate metabolism in high-fat diet (HFD)-induced hyperglycemic rats was evaluated. The co-incubation of L. plantarum with R. oligosporus during soy tempeh fermentation reduced the homeostatic model assessment of insulin resistance, HbA1c, serum glucose, total cholesterol, triglyceride, free fatty acid, insulin, and low-density lipoprotein contents and significantly increased the high-density lipoprotein content in HFD rats. It also increased the LAB counts as well as the bile acid, cholesterol, triglyceride, and short-chain fatty acid contents in the feces of HFD rats. Our results suggested that the modulation of serum glucose and lipid levels by LAB occurs via alterations in the internal microbiota, leading to the inhibition of cholesterol synthesis and promotion of lipolysis. Tempeh, produced with both L. plantarum and R. oligosporus, may be a beneficial dietary supplement for individuals with abnormal carbohydrate metabolism.

This study integrated coastal-watershed models and combined a risk assessment method to develop a methodology to investigate the impact resulting from coastal disasters under climate change. The mid-western coast of Taiwan suffering from land subsidence was selected as the demonstrative area for the vulnerability analysis based on prediction of sea level rise (SLR), wave run-up, overtopping, and coastal flooding under the scenarios of 2020 to 2039. Database from tidal gauges and satellite images were used to analyze sea level rise using EEMD (Ensemble Empirical Mode Decomposition). Extreme wave condition and storm surge were estimated by numerical simulation using WWM (Wind Wave Model) and POM (Princeton Ocean Model). Coastal inundation was then simulated via WASH123D watershed model. The risk map of study areas based on the analyses of vulnerability and disaster were established using the AHP (Analytic Hierarchy Process) technique. Predictions of sea level rise, the maximum wave condition and storm surge under the scenarios of 2020 to 2039 are presented. The results indicate that the sea level at the mid-western coast of Taiwan will rise in an average of 5.8 cm, equivalent to a rising velocity of 2.8 mm/year. The analysis indicates that Wuqi, Lukang, Mailiao, and Taixi townships are susceptive, low resistant and low resilient, and reaches the high risk level. The assessment provides that important information for making adaption policy in the mid-western coast of Taiwan.

The modeling of flood-induced bend scour near embankment toes can provide important information for river engineering, embankment safety warnings, and emergency action management. During the rainy seasons, short-term general scour and bend scour are the most common causes for the failure of reinforced concrete embankments in Taiwan. To gain a deeper understanding of the scouring process near levee foundations, this study proposed a straightforward and practical method for bend scour simulation. The proposed simulation method is subdivided into three stages: two-dimensional flow simulation, general scour estimation, and bend scour estimation. A new bend-scour computation equation is proposed and incorporated into a two-dimensional hydraulic finite-volume model for simulating the evolution of bend scour depth around embankment toes. The proposed method is applied to simulate the temporal evolution of bend scouring near the Shuideliaw Embankment on the Cho-Shui River in Taiwan, where serious failure occurred during the June 2012 monsoon. Field data were gathered using the numbered-brick technique at the Shuideliaw Embankment to demonstrate the accuracy of the proposed method. The results of the bend scour simulations compared reasonably well with field measurements, indicating close agreement in terms of water levels and bend scour depths near the Shuideliaw Embankment. The proposed method was found to quickly estimate the maximum short-term general scour and bend scour depths for further enhancement of the safety of the embankment toe.

Co-inhibitory receptors (Co-IRs) are essential in controlling the progression of immunopathology in rheumatoid arthritis (RA) by limiting T cell activation. The objective of this investigation was to determine the phenotypic expression of Co-IRs T cells and to assess the levels of serum soluble PD-1, PDL-2, and Tim3 in Taiwanese RA patients. Co-IRs T cells were immunophenotyped employing multicolor flow cytometry, and ELISA was utilized for measuring soluble PD-1, PDL-2, and Tim3. Correlations have been detected across the percentage of T cells expressing Co-IRs (MFI) and different indicators in the blood, including ESR, high sensitivity CRP (hsCRP), 28 joint disease activity scores (DAS28), and soluble PD-1/PDL-2/Tim3. In RA patients, we recognized elevated levels of PD-1 (CD279), CTLA-4, and TIGIT on CD4+ T cells; TIGIT, HLA-DR, TIM3, and LAG3 on CD8+ T cells; and CD8+CD279+TIM3+, CD8+HLA-DR+CD38+ T cells. The following tests proved to be correlated with hsCRP: CD4/CD279 MFI, CD4/CD279%, CD4/TIM3%, CD8/TIM3%, CD8/TIM3 MFI, CD8/LAG3%, and CD8+HLA-DR+CD38+%. CD8/LAG3 and CD8/TIM3 MFIs are linked to ESR. DAS28-ESR and DAS28-CRP exhibited relationships with CD4/CD127 MFI, CD8/CD279%, and CD8/CD127 MFI, respectively. CD4+CD279+TIM3+% was correlated with DAS28-ESR (p=0.0084, N=46), DAS28-CRP (p=0.007, N=47), and hsCRP (p=0.002, N=56), respectively. In the serum of patients with RA, levels of soluble PD-1, PDL-2, and Tim3 were extremely elevated. CD4+ TIM3+% (p=0.0089, N=46) and CD8+ TIM3+% (p=0.0305, N=46) were correlated with sTIM3 levels; sPD1 levels were correlated with CD4+CD279+% (p<0.0001, N=31) and CD3+CD279+% (p=0.0084, N=30). Co-IRs expressions on CD4+ and CD8+ T cells, as well as soluble PD-1, PDL-2, and Tim3 levels, could function as indicators of disease activity and potentially play crucial roles in the pathogenesis of RA, in accordance to our findings.