In recent years, wireless power transfer (WPT) has progressed rapidly in both theory and commercialization abroad. However, existing research into WPT coil design for low-power devices is limited. This paper investigates coil structure using printed circuit board (PCB) for magnetic resonant coupling WPT to address this gap. Specifically, the impacts of key geometric parameters on the coil quality factor and coupling coefficient are analysed through models and simulations. Equivalent PCB coils were formed for mutual inductance models, and four basic compensation circuits were analysed. The impacts of changes in coil thickness, line width, turn spacing, and number of turns on the quality factor of PCB coils were analysed with a fixed outer diameter of the coil. In this paper, to mitigate the coil offset while retaining PCB manufacturing simplicity for practical uses, a dual layer PCB coil structure is proposed. The structure optimizated PCB coil could offer remarkable improvements in the WPT system for low power electronic devices.

With the development of the photovoltaic industry, there will be an increasing demand for efficient, high-power density, and low-cost grid interface converters. Compared with two-level inverters, multilevel inverters have the following advantages: (1) lower device voltage ratings; (2) better output filtering spectrum; (3) lower electromagnetic interference (EMI) noise; and (4) higher switching speed capability. However, the complex switching circuit of the multilevel inverter will bring more parasitic inductance, resulting in more serious switching overvoltage (ringing). Consider that commonly used overvoltage absorption schemes are effective only for overvoltage or sup-pression of oscillations. Therefore, a new overvoltage absorption circuit is proposed in this paper, which can not only alleviate the overvoltage and ringing phenomena but also suppress the effect of voltage jumps during low-frequency switching on high-frequency input voltage. This overvoltage absorption circuit is characterized by low overvoltage, fast ringing damping, and minimum ca-pacitance. Experiments and simulations are conducted to verify the effectiveness of this overvoltage absorption circuit using a three-level ANPC inverter as a prototype. The results show that the proposed overvoltage absorption circuit can significantly reduce the overvoltage level, shorten the oscillation time, and reduce the voltage difference between the upper and lower DC bus capacitors.

In small animal models of severe acute respiratory syndrome coronaviruses (SARS-CoV and SARS-CoV-2) infection, ferrets (Mustela putorius furo) have been used to investigate the pathogenesis. Podoplanin (PDPN) is an essential marker in lung type I alveolar epithelial cells, kidney podocytes, and lymphatic endothelial cells. Monoclonal antibodies (mAbs) against ferret PDPN (ferPDPN) are useful for the pathological analyses of those tissues. We previously established an anti-ferPDPN mAb, PMab-292 using the Cell-Based Immunization and Screening (CBIS) method. In this study, we determined the critical epitope of PMab-292 using flow cytometry. The N-terminal ferPDPN deletion mutants analysis revealed that the Val34 is located at the N-terminus of the PMab-292 epitope. Furthermore, the PA tag-substituted analysis (PA scanning) showed that Asp39 is located at the C-terminus of PMab-292 epitope. The epitope sequence (₃₄-VRPEDD-₃₉) also exists between Val26 and Asp31 of ferPDPN, indicating that PMab-292recognizes the tandem repeat of the VRPEDD sequence of ferPDPN.

Partial differential equations (PDEs) are used to describe a wide range of phenomena, such as heat transfer, fluid dynamics, and quantum mechanics. By solving PDEs, we can ob- tain insights into the behavior of the system and make predictions about its future evolution. Conventional numerical methods for obtaining the approximate solutions of PDEs may re- quire extensive computational resources and time, especially for complex PDEs and large- scale problems. The recently developed physics-informed neural network (PINN) has shown promise in a variety of scientific and engineering fields by incorporating physical laws into the loss functions of the neural network (NN). In addition, the training of PINN does not require ground truth data, but it has poor generalization ability to unseen domains. On the other hand, a convolutional neural network (CNN) has fast inference and better generalization ability, but it requires a large amount of training data. Taking the advantages of PINN and CNN by using Legendre multiwavelets (LMWs) as basis functions, we introduce a new method to approach the PDEs in this paper, namely Physics-Informed Legendre Multiwavelets CNN (PiLMWs-CNN), in order to continuously approximate a grid-based state representation that can be handled by a CNN. PiLMWs-CNN enable us to train our models using only physics-informed loss functions without any pre- computed training data, simultaneously providing fast and continuous solutions that gener- alize to previously unknown domains. In particular, the LMWs can simultaneously possess compact support, orthogonality, symmetry, high smoothness, and high approximation order. Compared to orthonormal polynomial (OP) bases, the approximation accuracy can be greatly increased and computation costs can be significantly reduced by using LMWs. We applied PiLMWs-CNN to approximate the damped wave equation, incompressible Navier-Stokes (N- S) equation, and two-dimensional heat conduction equation. The experimental results show that this method provides more accurate, efficient, and fast convergence with better stability when approximating the solution of PDEs.

The stability and optimal control for an SIS epidemic model with demographics and heterogeneous control strategies (immunization and quarantine) on complex networks are investigated. The epidemic threshold, disease-free and endemic equilibria are derived. Then, global asymptotical stability about the two equilibria are studied based on different methods. Furthermore, the optimal control issue about the system is also considered. We obtain the existence and uniqueness of the optimal control and optimal control tactics. Some numerical simulations were conducted to illustrate and supplement the theoretical results. Meanwhile, the effects of the combination of various immunization and quarantine schemes are studied and also compared with the optimal control strategies.

Rapid urbanization has led to many ecological problems such as landscape fragmentation, decreased landscape connectivity, and decreased biodiversity. Building an ecological security pattern is an important way to ensure ecological security and maintain sustainable urban development. Harbin is an important large-scale city in northeastern China, and the urban central district of Harbin is used as the study area. Ecological sensitivity assessment, MSPA, gravity model, landscape connectivity assessment and MCR model were used to extract ecological source areas, ecological corridors and ecological nodes in the study area to construct and optimize the ecological security pattern. Research shows that: A total of 23 ecological source areas were identified, mainly located along the Songhua River in the central part of the study area and in the mountain forest areas within the A-cheng District in the southeastern part of the study area. 48 ecological corridors were extracted, mainly in Daowai District, A-cheng District and the eastern part of Xiangfang District. There are 8 important ecological corridors and 10 important connecting corridors. 61 ecological nodes of the first level and 65 ecological nodes of the second level were extracted. High, higher, medium, lower and low security areas were classified based on the minimum cumulative resistance surface, with the highest proportion of high ecological security areas accounting for 45.75% of the study area. 65 ecological breakpoints were extracted and restoration measures were proposed. Finally, The structure of the ecological security pattern optimization of "two axes, two belts and four areas" is proposed, and corresponding ecological management measures are put forward. The experimental system of this study can provide new ideas for the construction of ecological security patterns in other regions and provide scientific support for the ecological sustainable development of similar urban areas.

Climate and its fluctuations have wide-ranging impacts on the tourism industry. High temperatures, as a typical meteorological and climatic factor, influence tourists' travel intentions and spatial behavior. This study conducted a descriptive analysis and market trend analysis of Chinese tourism during periods of high temperatures, revealing several key findings. Firstly, tourists seeking respite from summer heat exhibit a preference for short-distance trips and resource-rich destinations. Secondly, heat-escape tourism products undergo changes over time, gradually shifting towards mountainous areas and waterfront locations. Furthermore, taking Shanghai Disneyland as a case study demonstrates that the holiday system holds greater significance than temperature constraints. Despite experiencing a significant decline in the quality of their tourist experience in high-temperature environments, long-distance travelers are not deterred from choosing pre-booked tourism products by sudden bouts of hot weather.

This paper propose a kernel geometric mean metric learning (KGMML) algorithm. The basic idea is to obtain the closed-form solution of the geometric mean metric learning (GMML) algorithm in the high-dimensional feature space determined by the kernel function. Then, the solution is generalized as a form of kernel matrix by using the integral representation of the weighted geometric mean and the Woodbury matrix in this new feature space. Experimental results on 15 datasets show that the proposed algorithm can effectively improve the accuracy of the GMML algorithm and other metric algorithms.

Ultra-high temperature oxidation-resistant alloys (UTORAs) have received a lot of attention due to the increased research demand for deep space exploration around the world. But UTORAs have the disadvantages of easy oxidation and chalking. So, in this study, a UTORA was prepared by hot-press sintering on VZrHfNbTa (HEA) substrate coated with hafnium. The bonding mechanism, resistance to high-temperature oxidation, and hardness of the sample tests were carried out. The results show that zirconium in the matrix will diffuse into the hafnium coating during the high-temperature sintering process and form the HfZr alloy transition layer, the coating thickness of the composite is about 120 μm, and the diffusion distance of zirconium in the hafnium coating is about 60 μm, this transition layer chemically combines the hafnium coating and the HEA substrate into a monolithic alloy composite. The results of high-temperature oxidation experiments show that the oxidation degree of the hafnium-coated VZrHfNbTa composite material was significantly lower than that of the VZrHfNbTa HEA after oxidation in air at 1600 °C for 5 h. The weight gain of the coated sample after oxidation is 56.56 mg/cm2, which was only 57.7 % compared to the weight gain of the uncoated sample (98.09 mg/cm2 for uncoated), and the surface of the uncoated HEA showed obvious dents, oxidation, and pulverization occurred on the surface and interior of the sample. In contrast, the coated composite alloy sample mainly underwent surface oxidation sintering to form a dense HfO2 protective layer, and the internal oxidation of the hafnium-coated VZrHfNbTa composite alloy was significantly lower than that of the uncoated VZrHfNbTa HEA.

A large number of studies have concluded that since housing pressure will affect the mobility of highly skilled young migrants (HSYM) in Chinese cities and regions, it is necessary to apply corresponding housing policies to adjust housing unaffordability for HYSM. This study uses a survey data conducted in China's Zhejiang Province of China, where specific policies have been implemented to attract talent and found that housing does crowds out the HSYM from a city, but the HSYM who have a master's degree or above or who work in government organizations or state-owned enterprises are more tolerant of housing unaffordability. The unmarried or those staying in the city for a long period are less tolerant of housing unaffordability. Meanwhile, there are the heterogeneous impacts of factors on the HSYM's tolerance for housing unaffordability across cities of different levels. Therefore, housing policies should highlight urban differences and intra-group differences.

Rapid advancements in the fifth generation (5G) communication technology and mobile edge computing (MEC) paradigm lead to the proliferation of unmanned aerial vehicles (UAV) in urban air mobility (UAM) networks, which provide intelligent services for diversified smart city scenarios. Meanwhile, the widely deployed internet of drones (IoD) in smart cities also brings up new concerns on performance, security, and privacy. The centralized framework adopted by conventional UAM networks is not adequate to handle high mobility and dynamicity. Moreover, it is necessary to ensure device authentication, data integrity, and privacy preservation in UAM networks. Thanks to characteristics of decentralization, traceability, and unalterability, Blockchain is recognized as a promising technology to enhance security and privacy for UAM networks. In this paper, we introduce LightMAN, a lightweight microchained fabric for data assurance and resilience-oriented UAM networks. LightMAN is tailored for small-scale permissioned UAV networks, in which a microchain acts as a lightweight distributed ledger for security guarantees. Thus, participants are enabled to authenticate drones and verify the genuineness of data that is sent to/from drones without relying on a third-party agency. In addition, a hybrid on-chain and off-chain storage strategy is adopted that not only improves performance (e.g,.latency and throughput) but also ensures privacy preservation for sensitive information in UAM networks. A proof-of-concept prototype is implemented and tested on a Micro Air Vehicle Link (MAVLink) simulator. The experimental evaluation validates the feasibility and effectiveness of the proposed LightMAN solution.

The eutrophication caused by excessive total nitrogen(TN) and total phosphorus(TP) emissions has been widely concerned by the whole society. Studies have revealed the relationship between land use and TN and TP, but the relationship between land use compound topographic position and TP and TN was seldom studied. Therefore, Spearman correlation and redundancy analyses were used to reveal the relationship between land use compound topographic position and TN and TP based on the monthly data of 28 water quality sampling sites and the land use data of 2013 and 2016 in the lakes of Guizhou Plateau. The results show that the nutritional state of the HBA watershed is medium. The trophic level index (TLI) value and TN concentration were high during flood, while TP concentration was high in dry period. The TN concentration in the tributaries was higher than that in the reservoir area. Construction and valley were the sources of the pollution, whereas forest land and gentle slope were the sink. According to the”source-sink”effect, the optimal zoning of land use was completed, and the urban land pollution govern area should be strengthened firstly. This paper can provide decision support for water environment management and sustainable development decision-making.

This paper proposes a parameter coordination optimization design of Power System Stabilizer (PSS) based on an improved Quasi-Affine Transformation Evolutionary (QUATRE) algorithm to suppress low-frequency oscillation and improve the dynamic stability of power system. To begin, the Simulated Annealing (SA) algorithm randomly updates the globally optimal solution of each QUATRE iteration and matches the inferior solution with a certain probability to escape the local extreme point. This new algorithm is first applied to power system. Second, Since damping ratio is one of the criteria to measure the dynamic stability of power system, this paper sets the objective function according to the principle of maximization of damping coefficient of electromechanical mode, and uses SA-QUATRE to search a group of global optimal PSS parameter combinations to improve the stability margin of the system as much as possible. Finally, the method's rationality and validity were validated by applying it to the simulation examples of IEEE 4-machine 2-area system with different operation states. The comparison with the traditional optimization algorithm shows that the proposed method has more advantages for multi-machine PSS parameter coordination optimization, and can restrain the low-frequency oscillation of power system more effectively and enhance the system stability.

Micro-grids’ operations offer local reliability; in the event of faults or low voltage/frequency events on the utility side, micro-grids can disconnect from the main grid and operate autonomously while providing the continued supply of power to local customers. With the ever-increasing penetration of renewable generation, however, the operations of micro-grids become increasingly complicated because of the associated fluctuations of voltages. As a result, transformer taps are adjusted frequently, thereby leading to the fast degradation of expensive tap-changer transformers. In the islanding mode, the difficulties also come from the drop of voltage and frequency upon disconnecting from the main grid. To appropriately model the above, the nonlinear AC power flow constraints are necessary. Computationally, the discrete nature of tap-changer operations and the stochasticity caused by renewables add two layers of difficulty on top of a complicated AC-OPF problem. To resolve the above computational difficulties, the main principles of the recently-developed "l1-proximal" Surrogate Lagrangian Relaxation are extended. Testing results based on 9-bus system demonstrate the efficiency of the method to obtain the exact feasible solutions for micro-grid operations thereby avoiding approximations inherent to existing methods, while demonstrating that through the optimization, 1. the number of tap changes is drastically reduced, and 2. the method is capable of handling networks with meshed topologies.

This paper considers the principles of building a circuit model of film resistor cutting. The conductive resistive medium is defined with the component equations and the topology of the circuit model. A method of estimating the electric parameters of a resistor operating in the system with a measuring voltage source is shown. An equation system for the node voltages is defined, and the resistive layer parameters are analyzed as the circuit model structure changes during the cutting process.

This study provides a novel method to prepare metal-ceramic composites from magnetically selected iron ore using microwave heating. By introducing three different microwave susceptors (Activated Carbon, SiC, and a mixture of Activated Carbon and SiC) during the microwave process, effective control of the ratio of metallic and ceramic phases has been achieved easily. The effects of the three susceptors on the microstructure of the metal-ceramics and the related reaction mechanisms were also investigated in detail. The results show that the metal phase (Fe) and ceramic phase (Fe2SiO4, FeAl2O4) can be maintained, but the metal phase to ceramic phase changed significantly. In particular, the microstructures appeared as well-distributed nanosheet structures with diameters of ~400 nm and thicknesses of ~20 nm when SiC was used as the microwave susceptor.

Blockchain technology has been recognized as a promising solution to enhance the security and privacy of Internet of Things (IoT) and Edge Computing scenarios. Taking advantage of the Proof-of-Work (PoW) consensus protocol, which solves a computation intensive hashing puzzle, Blockchain assures the security of the system by establishing a digital ledger. However, the computation intensive PoW favors members possessing more computing power. In the IoT paradigm, fairness in the highly heterogeneous network edge environments must consider devices with various constraints on computation power. Inspired by the advanced features of Digital Twins (DT), an emerging concept that mirrors the lifespan and operational characteristics of physical objects, we propose a novel Miner-Twins (MinT) architecture to enable a fair PoW consensus mechanism for blockchains in IoT environments. MinT adopts an edge-fog-cloud hierarchy. All physical miners of the blockchain are deployed as microservices on distributed edge devices, while fog/cloud servers maintain digital twins that periodically update miners’ running status. By timely monitoring miner’s footage that is mirrored by twins, a lightweight Singular Spectrum Analysis (SSA) based detection achieves to identify individual misbehaved miners that violate fair mining. Moreover, we also design a novel Proof-of-Behavior (PoB) consensus algorithm to detect byzantine miners that collude to compromise a fair mining network. A preliminary study is conducted on a proof-of-concept prototype implementation, and experimental evaluation shows the feasibility and effectiveness of proposed MinT scheme under a distributed byzantine network environment.

Objectives: In order to solve the problem that most of the existing research focuses on the binary tactile attributes of objects,which ignores the tactile attribute strength and category recognition,an attribute strength and category recognition method based on convolutional neural network matrix-label is proposed. Methods:Firstly,in the data preparation stage,we preprocess the raw data and determine the matrix labels to build the haptic dataset.Secondly,in the feature extraction stage,we fuse the haptic data of two fingers and use the convolutional neural network to extract the attribute strength features.Finally,in the attribute strength and category recognition stage,all channel haptic data is fused to predict the attribute strength and category.Results:We compared with the multi-label convolutional neural network method in terms of elastic strength,hardness strength and category,and compared the attribute strength recognition capabilities of the two methods using novel objects outside the haptic dataset.The results show that the accuracy of the last 20 iterations of the matrix-label method has an average elastic strength of 96.73%,hardness strength of 97.34%,and category of 96.67%.The performance is better.When the Euclidean distance between the prediction of the novel object and the real label is less than 1,the accuracy of the elastic strength is best to reach 100%,and the hardness strength is best to reach 100%.The performance is better. Conclusions:The effectiveness of the method has been verified.Comparing with the convolutional neural network method,our method can effectively recognize the attribute strength and category of objects.

Truffles contribute to crucial dynamics in the soil systems, being involved in plentiful ecological functions important for ecosystems. Despite this, the interactions between truffles and surrounding mycobiota remain unknown. Here, we aimed to shed light on how much truffle species could affect its surrounding soil mycobiota. Using traditional chemical analysis and Illumina ITS amplicon sequencing, we compared soil nutrients and mycobiota surrounding two truffle species: Tuber indicum (Ti) and T. pseudohimalayense (Tp) inhabit in the same Pinus armandii forest in southwestern China. Tp soil was more acidic and had higher nutrients (total C, N, P contents) than Ti soil. Fungal richness and diversity of truffle ascomata and surrounding soils were significantly higher in Tp than in Ti. Redundancy analysis showed relationships between soil fungal taxa and soil properties had changed from negative (Tp) to positive (Ti) and shifted from a moisture-driving (Tp) to a total N-driving (Ti). Overall, our results showed that the interactions between truffle and soil system had been altered with species variation, although the causative peculiarity of these associations needs to be further studied.

The objective of this study is to measure the crack propagation speed in three types of self-compacting concrete reinforced with steel fibers loaded under four different loading rates. Central-notched prismatic beams with two types of fibers (13 mm and 30 mm in length), three fiber volume ratios, 0.51%, 0.77% and 1.23%, were fabricated. Four strain gages were glued on one side of the specimen notch to measure the crack propagation velocity, a fifth one at the notch tip to estimate the strain rates upon the initiation of a cohesive crack and the stress-free crack. A servo-hydraulic testing machine and a drop-weight impact device were employed to conduct three-point bending tests at four loading-point displacement rates, the former to perform tests at 2.2 μm/s, 22 mm/s and the latter for those at 1.77 m/s, 2.66 m/s, respectively. With lower fiber contents, smooth mode-I cracks were formed, the crack speed reached the order of 1 mm/s and 20 m/s. However, crack velocities up to 1417 m/s were obtained for the concrete with high content of fibers under impact loading. This value is fairly close to the theoretically predicted terminal crack velocity of 1600–1700 m/s. Numerical simulations based on cohesive theories of fracture and preliminary results based on the technique of Digital Image Correlation are also presented to complement those obtained from the strain gages. In addition, the toughness indices are calculated under all four loading rates. Strain hardening (softening) behavior accounting from the initiation of the first crack is observed for all three types of concrete at low (high) loading rates. Significant enhancement in the energy absorption capacity is observed with increased fiber content.

RNA polymerase II (RNAPII) frequently transcribes non-protein coding DNA sequences in eukaryotic genomes into long non-coding RNA (lncRNA). Here, we focus on the impact of the act of lncRNA transcription on nearby functional DNA units. Distinct molecular mechanisms linked to the position of lncRNA relative to the coding gene illustrate how non-coding transcription controls gene expression. We review the biological significance of the act of lncRNA transcription on DNA processing, highlighting common themes, such as mediating cellular responses to environmental changes. This review presents the background in chromatin signaling to appreciate examples in different organisms where we can interpret functions of non-coding DNA through the act of RNAPII transcription.

Thanks to rapid advances in the Internet of Things (IoT) and Edge-Fog-Cloud Computing technologies, Smart Public Safety (SPS) system has become feasible by integrating heterogeneous computing devices and different types of networks to collaboratively provide seamless public safety services. While SPS facilitates convenient exchanges of surveillance data streams among device owners and third-party applications, the existing monolithic service oriented architecture (SOA) architecture is unable to provide scalable and extensible services in a large-scale heterogeneous network environment. Moreover, traditional security solutions rely on centralized trusted third-party authority, which not only can be a performance bottleneck or the single point of failure, but it also incurs privacy concerns on improperly use of private information. Inspired by blockchain and microservices technologies, this paper proposed a BLockchain-ENabled Decentralized Smart Public Safety (BlendSPS) system. Leveraging hybrid blockchain fabrics, a microservices based security mechanism is implemented to enable decentralized security architecture, and it supports immutability, auditability and traceability for secured data sharing and operations among participants of the SPS system. An extensive experimental study verified the feasibility of the proposed Blend-SPS that possesses security and privacy proprieties with limited overhead on IoT based edge networks.

In this paper, the methodology using Insect Intelligent Building (I^2B) technology for establishing energy consumption monitoring system of public buildings is prevailed. The computing process node and distributed algorithm are utilized to implement the energy consumption collection and data transmission and data pre-processing. Taking a commercial building as a case study, CPNs are applied to set up the building energy consumption monitoring system, with the Spanning Tree Algorithm for generating network topology，and BPNN method for solving abnormal data and recovering missing data. The research results demonstrate the proposed method can effectively improve the performance of plug-and-play and self-identified and self-configuration of energy consumption monitoring system.

Over the past few years, the importance of video surveillance in securing the national critical infrastructure has significantly increased, whose applications include detecting failures and anomalies. Accompanied by video proliferation is the increasing number of attacks against surveillance systems. Among the attacks, false frame injection (FFI) attacks that replay video frames from a previous recording to mask the live feed has the highest impact. While many attempts have been made to detect FFI frames using features from the video feeds, video analysis is computationally too intensive to be deployed on-site for real-time false frame detection. In this paper, we investigate the feasibility of FFI attacks on compromised surveillance systems at the edge and propose an effective technique to detect the injected false video and audio frames by monitoring the surveillance feed using the embedded Electrical Network Frequency (ENF) signals. An ENF operates at a nominal frequency of 60 Hz/50 Hz based on its geographical location and maintains a stable value across the entire power grid interconnection with minor fluctuations. For surveillance system video/audio recordings connected to the power grid, the ENF signals are embedded. The time-varying nature of the ENF component is used as a forensic application for authenticating the surveillance feed. The paper highlights the ENF signal collection from a power grid creating a reference database and ENF extraction from the recordings using conventional short-time Fourier Transform and spectrum detection for robust ENF signal analysis in the presence of noise and interference caused in different harmonics. The experimental results demonstrate the effectiveness of ENF signal detection and/or abnormalities for FFI attacks.

Ammonia-oxidizing microorganism communities are abundant and functionally efficacious in nitrification. However, ammonia-oxidizing archaea (AOA) and ammonia-oxidizing bacteria (AOB) groups complicate this process in subtropical streams. This study investigates the abundance of ammonia-oxidizing communities south of the Dabie Mountains, China, using quantitative polymerase chain reaction (qPCR). Clone libraries were utilized to analyze the abundance and microbial structures of AOA and AOB in sediments. Such analysis may provide strong evidence reflecting the links within the environment. The results show that AOB had a lower abundance of copies of the ammonia-oxidizing gene (amoA) than AOA. Interestingly, the AOA and AOB community compositions were correlated with ecological characteristics. The dissolved oxygen (DO) and oxidation-reduction potential (ORP) had significant positive correlations, whereas the phosphorus within the structure had a negative correlation with the abundance of both groups. Our study shows that it might adopt some species related to Nitrosotalea clusters that can resist comparably higher pH (toward pH 6.5). Together, these results imply that the physiological adaptation of microbial guilds to environmental pressures in ammonia-oxidizing archaea might allow them to have a more substantial function of ammonia-oxidizing communities in natural habitats.

Leaf variegation pale yellowing is observed in the Calcineurin B-Like-Interacting Protein Kinase14 (CIPK14) overexpression line (oeCIPK14) and double knockout WHIRLY1/WHIRLY3 (why1/3) lines of Arabidopsis, the distribution of WHIRLY1 (WHY1) protein between plastids and the nucleus are affected by the phosphorylation of WHY1 by CIPK14. To elucidate the coregulation of CIPK14 and WHIRLY1/WHIRLY3 mediated leaf pale yellowing, a differential proteomic analysis is conducted between the oeCIPK14 variegated (oeCIPK14-var) line, why1/3 variegated (why1/3-var) line and wild type (WT). More than 800 protein spots are distinguished on each gel, 67 differential abundance proteins (DAPs) are identified by matrix-assisted laser desorption ionization-time of flight/time of flight mass spectrometry (MALDI-TOF/TOF-MS), of which, 34 DAPs are in the oeCIPK14-var, 33 DAPs are in the why1/3-var compared to WT. Five overlapping proteins differentially change both in the oeCIPK14-var and in the why1/3-var. They are ATP-dependent Clp protease proteolytic subunit-related protein 3 (ClpR3), Ribulose bisphosphate carboxylase large chain (RBL), Beta-amylase 3 (BAM3), Ribosome-recycling factor (RRF), Ribulose bisphosphate carboxylase small chain (RBS). Bioinformatics analysis show that most of DAPs are involved in photosynthesis, defense and antioxidation pathway, protein metabolism, amino acid metabolism, energy metabolism, malate biosynthesis, lipid metabolism and transcription. Thus, the photosystem parameters are measured that the content of chlorophyll, the photochemical efficiency of PSⅡ (Fv/Fm), and electron transport rates (ETR) decrease in the why1/3-var and oeCIPK14-var, but the non-photochemical quenching (NPQ) increases. Both mutants show high sensitivity to strong light. Based on the annotation of DAPs from both why1/3-var and oeCIPK14-var lines, we conclude that CIPK14 phosphorylation mediated WHY1 deficiency in plastids is related to impairment of protein metabolism leading to chloroplast dysfunction.

This paper develops a novel dynamic correction method for the reliability assessment of large oil-immersed power transformers. First, with the transformer oil-paper insulation system (TOPIS) as the target of evaluation and the winding hot spot temperature (HST) as the core point, an HST-based static ageing failure model is built according to the Weibull distribution and Arrhenius reaction law, in order to describe the transformer ageing process and calculate the winding HST for obtaining the failure rate and life expectancy of TOPIS. A grey target theory based dynamic correction model is then developed, combined with the data of Dissolved Gas Analysis (DGA) in power transformer oil, in order to dynamically modify the life expectancy calculated by the built static model, such that the corresponding relationship between the state grade and life expectancy correction coefficient of TOPIS can be built. Furthermore, the life expectancy loss recovery factor is introduced to correct the life expectancy of TOPIS again. Lastly, a practical case study of an operating transformer has been undertaken, in which the failure rate curve after introducing dynamic corrections can be obtained for the reliability assessment of this transformer. The curve shows a better ability of tracking the actual reliability level of transformer, thus verifying the validity of the proposed method and providing a new way for transformer reliability assessment. This contribution presents a novel model for the reliability assessment of TOPIS, in which the DGA data, as a source of information for the dynamic correction, is processed based on the grey target theory, thus the internal faults of power transformer can be diagnosed accurately as well as its life expectancy updated in time, ensuring that the dynamic assessment values can commendably track and reflect the actual operation state of the power transformers.

The segmentation of urban scene mobile laser scanning (MLS) data into meaningful street objects is a great challenge due to the scene complexity of street environments, especially in the vicinity of street objects such as poles and trees. This paper proposes a three-stage method for the segmentation of urban MLS data at the object level. The original unorganized point cloud is first voxelized, and all information needed is stored in the voxels. These voxels are then classified as ground and non-ground voxels. In the second stage, the whole scene is segmented into clusters by applying a density-based clustering method based on two key parameters: local density and minimum distance. In the third stage, a merging step and a re-assignment processing step are applied to address the over-segmentation problem and noise points, respectively. We tested the effectiveness of the proposed methods on two urban MLS datasets. The overall accuracies of the segmentation results for the two test sites are 98.3% and 97%, thereby validating the effectiveness of the proposed method.

Our results demonstrated that SWT stimulates osteoblastogenesis and increase the cell number of osteoblasts, suggesting positive regulatory effects on osteoblast differentiation. However, the effect of SWT on bone formation need further examination, since the expression of alp gene is downregulated. On the other hand, SWT appears to negatively regulate osteoclast differentiation and bone resorption, as number of osteoclasts and the expression of critical bone resorptive genes are all downregulated. Collectively, SWT might change the equilibrium of bone remodeling and increase the bone mass. Our data provided supportive evidences that this medicine formulation can be applied to treat osteoporosis or bone destructive diseases.

The microglia, displaying diverse phenotypes, play a significant regulatory role in the development, progression, and prognosis of Parkinson's disease. Research has established that glycolytic reprogramming serves as a critical regulator of inflammation initiation in pro-inflammatory macrophages. Furthermore, the modulation of glycolytic reprogramming has the potential to reverse the polarized state of these macrophages. Previous studies have shown that levetistilide A (LA), a phthalide component derived from Angelica sinensis, possesses a range of pharmacological effects, including anti-inflammatory, antioxidant, and neuroprotective properties. In our study, we have examined the impact of LA on inflammatory cytokines and glucose metabolism in microglia induced by lipopolysaccharide (LPS). Furthermore, we explored the effects of LA on the AMPK/mTOR pathway and assessed its neuroprotective potential both in vitro and in vivo. The findings revealed that LA notably diminished the expression of M1 pro-inflammatory factors induced by LPS in microglia, while leaving M2 anti-inflammatory factor expression unaltered. Additionally, it reduced ROS production and suppressed IκB-α phosphorylation levels as well as NF-κB p65 nuclear translocation. Notably, LA exhibited the ability to reverse microglial glucose metabolism reprogramming and modulate the phosphorylation levels of AMPK/mTOR. In vivo experiments further corroborated these findings, demonstrating that LA mitigated the death of TH-positive dopaminergic neurons and reduced microglia activation in the ventral SNpc brain region of the midbrain and the striatum. In summary, LA exhibited neuroprotective benefits by modulating the polarization state of microglia and altering glucose metabolism, highlighting its therapeutic potential.

This study evaluates the incidence and characteristics of adverse events (AEs) following the second COVID-19 booster dose, leveraging Taiwan's distinctive approach of extending booster vaccinations to all citizens, unlike the targeted high-risk group strategies in other countries. Utilizing data from Taipei Veterans General Hospital's Vaccine Adverse Event Reporting System (VAERS) from October 27, 2022, to January 19, 2023, the research examines AEs in 441 out of 1711 second booster recipients, considering factors like age, vaccine brands, and booster combinations. The findings reveal incidence rates (IR) of 25.6% (95% CI: 21.1-30.8) after the first booster and 24.9% (95% CI: 20.5-30.0) after the second, mostly non-serious, with those having AEs post-first booster 5 times more likely to report them again (Incidence rat rato, 5.02, P<0.001). Significantly, switching from the mRNA1273 vaccine to another brand reduced AE risk by 18%. The study underscores that AEs are more repetitive than cumulative with additional booster doses, advocating for personalized vaccination strategies based on individual medical histories and previous vaccine reactions. These insights are valuable for healthcare providers in discussing potential AEs with patients, thereby improving vaccine compliance and public trust, and for policymakers in planning future booster vaccination strategies.

Assessment of the genetic distinctiveness of a cultivar through morphological descriptors is an important tool for both the registration and the protection. New mango genotypes have been improved using valuable diverse germplasm resources to ensure food security. DNA fingerprinting based simple sequence repeats (SSR)-markers have been the most broadly used, effective and accurate in evaluation of genetic characterization of a cultivar. Molecular breeding is an effective source of genetic gain after improvement of fruit trees using marker assisted genomic selection. Mango (Mangifera indica L.) is an allotetraploid (2n = 4X= 40) drupe fruit and has high nutritional value belongs to genus Mangifera and family Anacardiaceae. Mango cultivars are used with worldwide acceptance to pharmacological, ethnomedical, and phytochemical industries. This study investigated the molecular evaluation of a new mango cultivar ‘Azeem Chaunsa’ using a set of the most effective 50 hyper-variable polymorphic SSR markers. Highly specific DNA fingerprints were identified in the genome of this mango cultivar, ‘Azeem Chaunsa’ compared with three standard cultivars such as Sindhri, Samar Bahisht (S.B) Chaunsa and Sufaid Chaunsa. Our results showed that SSR markers could efficiently assess genetic diversity in mango. An agglomerative hierarchical clustering method was used to construct dendrogram based on the ‘Unweighted Pair- Group Method with Arithmetic Mean’ (UPGMA). The genetic similarity coefficients were recorded between the mangos cultivars ranged from 0.49 to 0.67. Cultivar identification (CID) evaluates association among standard cultivars and Azeem Chaunsa and further concludes significant variations. CID results concluded that cultivar ‘Azeem Chaunsa’ varied significantly from the check cultivar, Sindhri (46.2%), S.B Chaunsa (45%) and Sufaid Chaunsa (46.7%). The results obtained in this study will orient cultivar identification strategies for a successful future mango breeding programmes in the context of climate change.

The UNUSUAL FLORAL ORGANS (UFO) gene is an essential regulatory factor of class B genes and plays a vital role in the process of inflorescence primordial and flower primordial development. We investigated the role of UFO genes in soybean to better understand the development of floral organs through gene cloning, expression analysis, and gene knockout. In situ hybridization demonstrated predominant expression of the GmUFO1 gene in the flower primordium. Phenotypic observation of GmUFO1 knockout mutant lines (Gmufo1) showed obvious alteration in floral organ number and shape, and mosaic organ formation. In contrast, GmUFO2 knockout mutant lines (Gmufo2) showed no obvious difference in floral organs. However, the GmUFO1 and GmUFO2 double knockout lines (Gmufo1ufo2) showed a more severe mutant phenotype than the Gmufo1 lines. Gene expression analysis also showed differences in the expression of major ABC function genes in the knockout lines. Based on the phenotypic and expression analysis, our results suggest the major role of GmUFO1 in the regulation of flower organ formation in soybean and that GmUFO2 does not have any direct effect, but it might have an interaction role with GmUFO1 in the regulation of flower development. In conclusion, the present study identified UFO genes in soybean and improved our understanding of floral development that could be useful for flower design in hybrid soybean breeding.

In this study, we evaluated the effects of Cyclosporine A (CsA) on Lipopolysaccharide (LPS)-induced cytokine production in the genital tract of female rabbits. Twelve sexually mature and healthy female rabbits were randomly divided into four groups (n = 3 each). The rabbits in the LPS group were given an intrauterine infusion of Escherichia coli LPS (4 mg/kg body weight (BW)). Rabbits in the CsA group were given CsA (20 mg/kg BW). Rabbits in the LPS + CsA group were given LPS (4 mg/kg BW) and CsA (20 mg/kg BW). The control group received only LPS and CsA carrier. The gene expression and protein levels of pro- and anti-inflammatory cytokines were observed using qRT-PCR and immuno-histochemical (IHC) assay, respectively. Our study showed that IL-1β, IL-6, IL-8, TNF-α, IFN-γ, IL-4, IL-10, IL-13, and TGF-β were expressed in female genital organs. The LPS challenge increased the mRNA expression of IL-6 and TNF-α in the uterine body and IL-1β in the uterotubal junction compared to the control group. CsA increased the basal mRNA expression of anti-inflammatory cytokines (i.e., IL-4 in the uterine body, uterotubal junction, and oviductal ampulla; IL-10 in the cervix, oviductal isthmus, and ampulla; and TGF-β in the uterotubal junction and oviductal ampulla) and pro-inflammatory cytokines (i.e., IL-6 and IL-8 in the cervix; IL-1β in the oviductal isthmus; TNF-α in the oviductal ampulla; and IFN-γ in the uterine body compared to the control group). In addition, CsA inhibited the mRNA expression of pro-inflammatory cytokines, such as IL-6 in the uterine body, uterotubal junction, and oviductal isthmus; TNF-α in the uterine body; and IFN-γ in the uterotubal junction and oviductal isthmus induced by the LPS challenge. The IHC assay showed the LPS-induced increase in protein production of IL-6 in the uterine body and oviductal isthmus. CsA increased the protein production of IL-10 in the cervix, uterine body, oviductal ampulla, and isthmus. Moreover, CsA decreased the protein production of IL-6 in the uterine body and oviductal isthmus induced by LPS.

The aim of this study was to examine oxidative stress and low level of alpha-1-antitrypsin (A1AT) in primary Sjögren's syndrome (pSS), and evaluate the associated autoreactivity against unmodified and their 4-hydroxy-2-nonenal (HNE)-modified peptides with pSS. Two differentially expressed proteins, alpha-1-acid glycoprotein 1 (A1AG1) and A1AT, exhibited 2-fold differences, and their HNE modifications were identified by depleted-albumin and immunoglobulin G (IgG) serum protein, in-solution digestion, in-gel digestion, and nano-LC-MS/MS from pSS patients and age-matched healthy controls (HCs). Furthermore, levels of proteins, confirmation of HNE modifications, HNE-protein adducts and autoreactivity against unmodified and their HNE-modified peptides were further validated. Levels of the HNE-protein adduct and A1AG1 were significantly higher in pSS patients than HCs, but levels of A1AT were significantly lower in pSS patients compared to HCs. Only the HNE modification of A1AT was confirmed. Further, concentrations of anti-A1AT^50-63 IgG and anti-A1AT^50-63 HNE IgA were significantly lower in pSS patients than HCs. Our study suggests that elevated HNE-protein adduct, oxidative stress, level [odds ratio (OR) 4.877, p = 0.003], lowered A1AT level (OR 3.910, p = 0.010) and a decreased level of anti-A1AT^50-63 IgG (OR 3.360, p = 0.010) showed an increased risk in pSS patients compared to HCs, respectively.

Effects of plastic deformation on the indentation feature of hot-rolled commercial pure titanium alloy were detected using microindentation. It was found that the most deformed sample experienced the largest indentation resistance and had the maximum dislocation density and the indentation size influenced the CP-Ti indentation feature. The Vicker hardness and energy dissipated demonstrated the significant influence of the dislocation motion and size effects on the indentation in the indentation deformation. The linear relation of the energy ratio which is related to the microstructures and the indentation depth ratio was obtained for hcp materials Titanium alloys.

Carbon fiber reinforced polymer (CFRP) bending structure is widely used in the aviation field. The occurrence and propagation of delamination damage will reduce the safety of in-service bending structures. As a detection tool with high damage sensitivity, Lamb wave can effectively identify delamination damage. In this study, the signal difference coefficient (SDC) was introduced to quantify delamination damage and evaluate the sensitivity of A0 and S0 mode lamb waves to delamination damage. The simulation results show that compared with the S0 mode Lamb wave, the A0 mode Lamb wave exhibits higher delamination damage sensitivity. The delamination damage can be quantified based on the strong correlation between the SDC and the delamination damage size. The control effect of the linear array PZT phase time-delay method on Lamb wave mode was investigated by simulation. The phase time-delay method realizes the generation of a single-mode Lamb wave, which can separately excite the A0 mode and S0 mode Lamb wave to identify delamination damage of different sizes. The A0 mode Lamb wave was excited by the developed one-dimensional linear comb transducer (LCT), which was used to conduct the detection experiment on the CFRP bending plate with delamination damage sizes of Φ6.0 mm, Φ10.0 mm, and Φ15.0 mm. The experimental results verify the correctness of the simulation. According to the Hermite interpolation results of the finite-element simulation data, the relationship between the delamination damage size and the SDC was fitted by the Gaussian function, which can accurately quantify the delamination damage. The absolute error of the delamination damage quantification with fitting expression is not larger than 0.8 mm, and the percentage error is not more than 8%.

In this work, oxygen-doped g-C3N4 mesoporous nanosheets (O-CNS) were synthesized via a facile recrystallization method with the assistance of H2O2. The crystal phase, chemical composition, morphological structure, optical property, electronic structure and electrochemical property of the prepared O-CNS samples were well investigated. The morphological observation combining with nitrogen adsorption-desorption results demonstrated that the prepared O-CNS samples possessed nanosheets-like morphology with porous structure. The O doping into g-C3N4 resulted in the augment of specific surface area, which could provide more active sites for photocatalytic reaction. Simultaneously, the visible-light absorption capacity of O-CNS samples was boosted owing to the regulation of O doping. The built energy level induced by the O doping could accelerate the migration rate of photoinduced carriers, and the porous structure was most likely to speed up the release of hydrogen during photocatalyic hydrogen process. Resultantly, the photocatalytic hydrogen production rate of the optimized oxygen-doped g-C3N4 nanosheets reached up to 2012.9 μmol•h-1•g-1, which was 13.4 times higher than that of bulk g-C3N4. Thus, the significantly improved photocatalytic behavior was imputed to the porous structure, the augment of active sites, and the enhancement of visible light absorption and charge separation efficiency.

The population parameters of the ecologically important mud shrimp Upogebia major were analyzed from 2012 to 2015 in tidal flats in Seonjaedo and Jugyo on the West coast of Korea. The shrimp density averaged 265/m2 in Seonjaedo and 118/m2 in Jugyo. The sex ratio varied monthly, often male-biased, but by size, males were significantly dominant, with a carapace length (CL) over 30 mm. Although the shrimp settled almost annually, only a single size-group was observed from 2012 to 2014. The recruitment in Jugyo in 2014 was notably successful, resulting in two cohorts persisting until 2015. Many shrimp were parasitized at varying local rates: 6.0% in Seonjaedo and 37.1% in Jugyo. The growth curves revealed that the shrimp grew annually after settlement, reaching CLs of 11.90, 18.24, and 23.02 mm in Seonjaedo and 13.73, 20.86, and 25.82 mm in Jugyo. Annual mortality was 77.2% in Seonjaedo and 67.4% in Jugyo. The estimated lifespan (tmax) was 10 years in Seonjaedo and 8 years in Jugyo, whereas the 2010 cohort in Jugyo largely disappeared in 5 years. Ovigerous females appeared from November to June and benthic juveniles between June and September. The shrimp’s growth was slower relative to other East Asian populations, likely due to colder sea water temperatures and altered food conditions from a higher shrimp density.

Data can be illustrated in shapes, and the shapes could provide insight for data modeling and information extraction. Topological data analysis provides an alternative insight in biomedical data analysis and knowledge discovery with the algebra topology tools. In present work, we study the application of topological data analysis for personalized electrocardiographic signal classification toward arrhythmia analysis. Using phase space reconstruction technique, the signal samples are converted into point clouds for topological analysis facility. With topological techniques the persistence landscapes from the point clouds are extracted as features to perform the arrhythmia classification task. We find that the proposed method is robust to the training set size, with only a training set size of 20% percents, the normal heartbeat class are 100% recognized, ventricular beats for 97.13%, supra-ventricular beats for 94.27% and fusion beats for 94.27% within the corresponding experiments. The property of keeping high performance when using smaller training sample proves that the proposed method is especially applicable to personalized analysis. With the present study, we show that the topological data analysis technique could be a useful tool in biomedical signal analysis, and provide powerful ability in personalized analysis.

In order to reduce the risk of grid transient voltage instability brought about by the new energy and system dynamic loads and the increasing proportion of new energy access, this paper proposes a differentiated dynamic reactive power compensation configuration method for suppressing transient voltage dip instability. The method first establishes a dynamic reactive power device configuration index system based on a multi-binary table, and then establishes a differentiated dynamic reactive power compensation device configuration model based on the node instability risk characteristics by combining with the regional division of system transient voltage instability risk. The model takes the investment cost and suppression effect as the optimization objectives, and realizes differentiated dynamic reactive power compensation by flexibly adjusting the optimization weights of economic benefits and reactive power compensation effects in the configuration process; Compared with the traditional compensation methods, differentiated compensation can significantly improve the economic benefits of reactive power compensation configuration. Finally, taking the IEEE39 node test system as an example, the improved TLBO algorithm is used to solve the model, which verifies the accuracy and effectiveness of the method proposed in this paper.

The popularity and development of social media has made it more and more convenient to spread rumors, and it has become especially important to detect rumor information from massive amounts of information. Most of the traditional rumor detection methods use content characteristics or propagation structure to mine rumor characteristics, ignoring the fusion characteristics of content and structure and their interaction characteristics. Therefore, a novel rumor detection method based on heterogeneous convolutional networks is proposed. Firstly, this paper constructs a heterogeneous map of joint rumor content and propagation structure to explore the interaction between content and propagation structure during rumor propagation and obtain rumor representation. On that basis, this paper uses the deep residual graph convolutional neural network to construct the content and structure interaction information of the current network propagation model. Finally, this paper uses the two datasets of Twitter15 and Twitter16 to verify the proposed method. Experimental results show that the proposed method has higher detection accuracy than the traditional rumor detection method.

A numerical method using combined detached-eddy simulation (DES) and cavitation model considering the rotation effect is used for unsteady cavitation flow field of the centrifugal pump. Closed type pump test system was established to obtain the pump performance and pressure pulsation characteristics under different flow rates and cavitation condition, which provide boundary conditions and verification of calculations. Based on the calculation results of the unsteady flow field of the centrifugal pump cavitation, the entropy generation analysis of the flow field and the pressure fluctuation characteristics were carried out. Then the relationship between cavitation and the deterioration of the centrifugal pump performance and the generation of the unstable operation excitation force was tried to reveal. The internal energy loss is mainly concentrated in the impeller, volute, and pump cavity area, which accounts for more than 85% of the total entropy generation. The characteristic frequency of about 0.333 Strouhal Number appears at the volute tongue due to the cavitation flow spread downstream.

Exploration geochemistry is an essential method for discover new mineral areas. However, with the increase of exploration degree, relying solely on "strong, broad and multiple" anomalies to guide exploration work has become increasingly challenging. How to effectively identify valuable geochemical information remains a hot and frontier topic in the field. Thus we proposed a geological connotation method (GCM) that provides an objective geological connotation to big geochemical data based on regional geological and geochemical characteristics of known typical deposits. There are mainly two types of geochemical anomalies expression: (1) the metallogenic intensity anomaly map (MIAM) obtained by accumulating specific anomalous elements, which directly reflects the degree of material exchange and superposition modification during mineralization; (2) the metallogenic type anomaly map (MTAM) obtained by accumulating the mineralization concentration coefficients of elements related to a certain genetic type, which can highlight the anomalies caused by a specific genetic type of deposit. These have been tried and applied in the exploration of the Gangdese, North Himalayas, Nyenchen Tanglha and other metallogenic belts in Tibet, and have made a series of breakthroughs in mineral resources exploration represented by Qulong, Zhunuo and Zhaxikang. The advantage of GCM is that it not only solves the problem of missing ore in the verification of "strong, broad and multiple" anomalies, but also can quickly and preferably delineate the strongest mineralized areas, and better overcome the influence of numerous factors on the anomalies, such as the chemical nature of elements, redox environment, geomorphic landscape and weathering and stripping, so that the anomaly evaluation becomes simple, objective and highlights the regularity.

This empirical research is part of a larger project beginning in 2020 and ongoing until 2023 exploring the impact of the COVID-19 pandemic on young caregivers aged 5-25 years and their families in Canada. Utilizing the social determinants of health as a conceptual framework, this case study emphasizes the voices of professionals offering services to young caregiver clients during the pandemic, and explores their perspectives on the impact of the pandemic on young caregivers and their families. Across three (3) different organizations offering programs and services to young caregiver clients in Ontario, six (6) individual interviews were conducted with directors/program managers and four (4) group interviews were conducted with thirteen (13) staff members who worked directly with young caregivers and their families. Nineteen (19) service providers participated in total. The results of this study highlight five (5) primary themes that emerged through data analysis: i) the role of service providers, ii) the impact of the COVID-19 pandemic on organizations and service providers supporting young caregivers and their families, iii) barriers for service users, iv) helpful resources for service providers and organizations, and v) resources needed/preferred by service providers and organization. The pandemic significantly impacted young caregivers and their families, as reported by professionals, and organizations working with young caregivers and their families were tasked with addressing increased service demands and adapting service delivery to follow public health guidelines.

As one of the most critical parameters to evaluate the quality and performance of mobile phones, real-time temperature monitoring of the mobile phone integrated chips is vitally important in the electronics industry. Although several different strategies for chip surface temperature measurement have been proposed in recent years, distributed temperature monitoring with the high spatial resolution is still a hot issue to be solved urgently. In this work, a fluorescent film material with photothermal properties containing thermosensitive upconversion nanoparticles (UCNPs) and polydimethylsiloxane (PDMS) is fabricated for chip surface temperature monitor-ing. The presented fluorescent films have thicknesses ranging from 23 to 90 μm and are both flexible and elastic. Using the fluorescence intensity ratio (FIR) technique, the temperature sens-ing properties of these fluorescent films are investigated. The maximum sensitivity of the fluo-rescent film was measured to be 1.43% K-1 at 299 K. By testing the temperature at different posi-tions of the optical film, a distributed temperature monitoring with a high spatial resolution down to 10 μm on the chip surface is successfully achieved. It is worth mentioning that the film maintains stable performance even under pull stretch up to 100%. The correctness of the method is verified by taking infrared images of the chip surface with an infrared camera. These results demonstrate that the as-prepared optical film is a promising anti-deformation material for high spatial resolution temperature monitoring on-chip surfaces.

The exponential growth of digital media content has introduced new challenges in managing and classifying internet traffic. Digital media traffic is composed of various applications such as video, audio, social media, and search, and its data structure is complex, incorporating a vast array of features. The classification of traffic data is a crucial aspect of internet traffic management and network security, and it forms the basis for several scenarios, including content distribution, advertising recommendations, and data analysis. Traditional classification methods rely mainly on deep packet inspection and port-based techniques, which have become increasingly ineffective due to the rapid evolution of network traffic. To address this issue, this study proposes a machine learning-based traffic classification method aimed at enhancing the accuracy and efficiency of digital media traffic classification to meet the current needs of traffic management and network security. The paper also analyzes and evaluates the classification effect and prediction capability of various algorithms under different training set sizes to validate the feasibility and effectiveness of the proposed method. The result demonstrates that the neural network algorithm has superior classification and prediction capabilities compared to the decision tree and support vector machine algorithms. Furthermore, our proposed method achieves the highest accuracy of 96.88% with a large training sample of 40,000 data streams, proving its superiority in handling high-dimensional data and complex datasets. The research results are significant for the development of digital media traffic classification and prediction methods and are expected to be applied in practical scenarios.

Newly build offshore wind farms (OWFs) render a collision risk between ships and installations. The paper proposed a real-time traffic monitoring method based on machine vision and deep learning technology to improve the efficiency and accuracy of the traffic monitoring system in the vicinity of offshore wind farms. Specifically, the method employs real automatic identification system (AIS) data to train a machine vision model, which is then used to identify passing ships in OWF waters. Furthermore, the system utilizes stereo vision techniques to track and locate the positions of passing ships. The method is tested in offshore water in China to validate its reliability. The results prove that the system sensitively detects the dynamic information of the passing ships, such as the distance between ships and OWFs, ship speed and course. Overall, this study provides a novel approach to enhancing the safety of OWFs, which is increasingly important as the number of such installations continues to grow. By employing advanced machine vision and deep learning techniques, the proposed monitoring system offers an effective means of improving the accuracy and efficiency of ship monitoring in challenging offshore environments.

Asaia bacteria commonly comprise part of the microbiome of many mosquito species in the genera Anopheles and Aedes, including important vectors of infectious agents. Their close association with multiple organs and tissues of their mosquito hosts enhances the potential for paratransgenesis for delivery of anti-malaria or anti-virus effectors. The molecular mechanisms involved in the interactions between Asaia and mosquito hosts, as well as Asaia and other bacterial members of the mosquito microbiome, remained unexplored. Here, we determined the genome sequence of the strain W12 isolated from Anopheles stephensi mosquitoes, compared them to other Asaia species associated with plants or insects, and investigated some properties of the bacteria relevant to their symbiosis with host mosquitoes. The assembled genome of strain W12 has a size of 3.94 MB, which is the largest among Asaia spp studied so far. At least 3,585 coding sequences were predicted. The insect-associated Asaia including strain W12 carried more glycoside hydrolase (GH) encoding genes (31 per genome) than those isolated from plants (22 per genome). W12 had the most predicted regulatory protein components (213) among the selected Asaia (ranging from 131 to 211), indicating its great capability to adapt to frequent environmental changes in the mosquito gut. Two complete operons encoding cytochrome bo3-type ubiquinol terminal oxidases (cyoABCD-1 and cyoABCD-2) were found in most of Asaia genomes, which possibly offer alternative terminal oxidases and allow the flexible transition of respiratory pathways. Genes involved in the production of acetoin and 2,3-butandiol have been identified in Asaia sp. W12.

A dual-platform colorimetric and ratiometric chemosensor, namely 6-(2-hydroxynaphthalen)-N-n-butyl-naphthalimide (HNA), based on Schiff base constructed from N-n-butyl-4-amino-1,8-naphthalimide and 2-hydroxy-1-naphthaldehyde has been designed and fabricated for detecting fluoride anion (F−) in DMSO solution. HNA is a colorimetic and ratiometric probe with superior selectivity and sensitivity. The color changes of HNA from yellow to purple was observed by the naked eyes in the presence of F−. The absorbance in the UV-Vis spectra of HNA was decreasing in 422 nm, while gradually increasing in 583 nm by adding F−. The limit of detection (LOD) of HNA for detecting F− is low to 0.61 μM and the binding model of HNA and F− is in 3:2 stoichiometry. Meanwhile, HNA can be used to detect F− in real samples. Finally, the mechanism of HNA for the detection of F− was investigated. The present work indicated that HNA would be a superior potential chemosensor in monitoring F− selectively and sensitively.

This paper investigated building data from multispectral and single-photon Lidar systems. The multispectral datasets from the individual channels and fused channels were explored. The multispectral and single-photon Lidar data were compared across multiple aspects: the data acquisition geometry, number of echoes, intensity, density, resolution, data defects, noise level, and the absolute and relative accuracy. In addition, we explored the performance of the multispectral and single-photon data for roof plane detection for eight complex/stylish buildings to investigate the suitability of these data for 3D building reconstruction. The building data from the single-photon and multispectral Lidar systems were evaluated with respect to the reference building vector data with an accuracy of better than 5 cm. The advantages and disadvantages of both technologies and their applications in the urban building environment are discussed.

Monitoring the dynamic responses of bridge structures has received considerable attention. It is important to synchronously measure both the quasi-static and dynamic displacements of bridge structures. However, the traditional accelerometer method cannot capture the quasi-static displacement component, although it can detect the dynamic displacement component. To this end, a novel composite instrument of a smartstation was proposed to monitor vibration displacements of footbridges. Full-scale experiments were conducted on a footbridge to validate the feasibility of the composite instrument-based monitoring method. A Chebyshev filter and wavelet algorithms were developed to process the composite instrument measurements. It was concluded that the measurement noise of the composite instrument was mainly distributed in a frequency range of 0–0.1 Hz. In two case studies with displacement peaks of 5.7–10.0 mm and 1.3– 2.5 mm, the composite instrument accurately identified the quasi-static and dynamic displacements. The composite instrument will be a potential tool for monitoring structural dynamics because of its enhanced overall performance.

Rice-Tartary buckwheat is a special type of Tartary buckwheat with easy hulling thin shell. The local rice-Tartary buckwheat ‘cv. Xiaomiqiao’ (XMQ) was used to explore the characteristics of photosynthesis, starch synthesis, yield and quality, as compared to Tartary buckwheat ‘cv. Jinqiao 2’(JQ2). XMQ showed significantly lower values of net photosynthetic rate, ADPGase activity and starch synthase activity at one or more periods during grain filling, as compared to that of JQ2. The effective branch number and grain number per plant of XMQ were similar to that of JQ2 regardless of different years, but the 1000-grain weight was significantly lighter that resulted in the significantly lower yield. XMQ accumulated similar contents of starch (amylose, amylopectin) and protein (glutelin, albumin, prolamin, globulin) to that of JQ2, but exhibited significantly lower flavonoid content. The values of peak viscosity and hot paste viscosity in XMQ were similar to that of JQ2, but the values of cool paste viscosity, breakdown and setback were significantly lower. In conclusion, XMQ showed low yield due to the insufficient of photosynthesis and starch synthesis. XMQ exhibited high nutritional quality as well as normal Tartary buckwheat and stored 18.88mg g-1 of flavonoid, that can be consumed as daily diet. The present results will provide a basis for food processing and breeding of rice-Tartary buckwheat.

A multi-strand composite welding wire was applied to join high nitrogen austenitic stainless steel, and microstructures and mechanical properties were investigated. The electrical signals demonstrate that the welding process using a multi-strand composite welding wire is highly stable. The welded joints are composed of columnar austenite and dendritic ferrite and welded joints obtained under high heat input and cooling rate have a noticeable coarse-grained heat-affected zone and larger columnar austenite in weld seam. Compared with welded joints obtained under the high heat input and cooling rate, welded joints have the higher fractions of deformed grains, high angle grain boundaries, Schmid factor and the lower dislocation density under the low heat input and cooling rate, which indicate a lower tensile strength and higher yield strength. The rotated goss (G_RD) orientation of a thin plate and the cube (C) orientation of a thick plate are obvious after welding, but the S orientation at 65° sections of Euler’s space is weak. The δ-ferrite was studied based on the primary ferrite solidification mode. It is observed that low heat input and high cooing rate result in the increasing of δ-ferrite and high dislocation density was obtained in grain boundaries of δ-ferrite. M₂₃C₆ precipitates due to low cooling rate and heat input in weld seam and deteriorates the elongation of welded joints. The engineering stress-strain curves also show the low elongation and tensile strength of welded joints under low heat input and cooling rate, which is mainly caused by the high fraction of δ-ferrite and the precipitation of M₂₃C₆.

Primary urethral malignancies are rare in clinical practice and elderly female are prone to suffer. The cause of PUC is unknown and may be related to long-term chronic inflammation, infection, sexual intercourse, pregnancy and irritation of the urethra. Incipient symptom of PUC is not distinctness and can easily lead to misdiagnosis. The final diagnosis relied on transvaginal ultrasound-guided mass biopsy and urethral biopsy. Early tumor treatment is mainly based on surgical resection. For advanced tumors, it is recommended to adopt a comprehensive treatment plan combining surgery, radiotherapy and chemotherapy We report this case with the aim of bringing attention to that primary urethral cancer progresses rapidly and has a poor prognosis, it is urged to call for a need of diagnostic and treatment specification.

Cu,N-TiO₂ nanotube (Cu,N-TNT) is prepared through a novel magnetron sputtering and anodic oxidation method. Then the morphology, structure and physicochemical property of Cu,N-TNT was analyzed by XRD, SEM, TEM, EDX and UV-vis-DR. The results indicate that the evenly doped copper is beneficial to the transformation of the TNT from anatase to rutile and play a key role in the morphology of the Cu,N-TNT. The doped Cu and N in the TNT influence the growth orientation of the TiO₂ crystals, which result in the lattice distortion and wider the interplanar spacing 60s-Cu,N-TNT has less band gap and stronger absorption intensity in visible region than other Cu,N-TNT samples, which make the combination rate of photogenerated electron and photogenerated hole decrease greatly, thus beneficial to its physicochemical property.

Our previous in vitro reports showed that crude extract prepared with 50% ethanol (ethanol crude extract, ECE) from Mongolian oak cups possessed excellent antioxidant capacities as well as inhibitory activities against α-glucosidase, α-amylase and protein glycation caused by its enrichment in phenolics, including mainly ellagic acid, kaempferol and their derivatives. Nevertheless, few in vivo studies on antidiabetic activities of these phenolics were conducted. The present study investigated hypoglycemic effects with normal and diabetic rats being administrated orally without or with ECE at 200 and 800 mg/kg for 15 days. In normal rats, no significant differences were exhibited after ECE administration in body weight, fasting blood glucose level, levels of chelesterol, triglyceride, LDL and AST in serum, organ indexes, and levels of GSH and MDA in organs. In diabetic rats, the fasting blood glucose level, indexes of heart and liver, and levels of chelesterol and triglyceride in serum and MDA in heart tissue were significantly decreased. Moreover, HDL levels in serum and SOD activities in the four organs of diabetic rats were significantly improved after ECE administration at 800 mg/kg. Thus, in addition to inhibiting α-glucosidase, α-amylase and protein glycation reported previously, oak cups might contain novel dietary phytonutrients in preventing abnormal changes in blood glucose and lipid profile and attenuating oxidant stress in vivo. The results also implied that it is ellagic acid, kaempferol and their derivatives enriched in ECE that might play vital roles in managing type 1 as well as type 2 diabetes.

The theoretical limit of link prediction is a fundamental problem in this field. Taking the network structure as object to research this problem is the mainstream method. This paper proposes a new viewpoint that link prediction methods can be divided into single or combination methods, based on the way they derive the similarity matrix, and investigates whether there a theoretical limit exists for combination methods. We propose and prove necessary and sufficient conditions for the combination method to reach the theoretical limit. The limit theorem reveals the essence of combination method that is to estimate probability density functions of existing links and nonexistent links. Based on limit theorem, a new combination method, theoretical limit fusion (TLF) method, is proposed. Simulations and experiments on real networks demonstrated that TLF method can achieve higher prediction accuracy.

Copper mine tailings are the residual products after the purification of precious copper from copper ores, and their storage can create numerous environmental problems. Many researchers have used copper mine tailings for preparation of geopolymer. This paper studies the enhancement of the cementitious activity of copper mine tailings in geopolymer system. First, copper mine tailings are activated through a mechanical grinding activation. Afterward, the mechanically activated copper mine tailings are further processed through thermal activation and alkaline roasting activating. The cementitious activity index of copper mine tailings is characterized through the degree of concentration of alkali leaching silicon and aluminum. It was observed that the Si and Al alkali leaching concentration of mechanical activated tailings was increased by 26.03% and 93.33%, respectively. The concentration of Si and Al was increased by 54.19% and 119.92%, respectively. For alkaline roasting activating, roasting time, temperature and (C/N ratio) were evaluated through the orthogonal test, and the best condition was activation for 120 min at 600℃ with C/N ratio is 5:1. In this study, the SEM, XRD and IR analysis show that mechanically activation, thermal activation and alkaline roasting activating can improve the cementitious activity index of copper mine tailings.

Indoor positioning based on the received signal strength (RSS) of the WiFi signal has become the most popular solution for indoor localization. In order to realize the rapid deployment of indoor localization systems, solutions based on crowdsourcing have been proposed. However, compared to conventional methods, crowdsourced RSS values are more erroneous and can result in large localization errors. To mitigate the negative effect of the erroneous measurements, a graph-based semi-supervised learning (G-SSL) method is used to exploit the correlation between the RSS values at nearby locations to estimate an optimal RSS value at each location. Before using the G-SSL method, the Linear Regression (LR) algorithm is proposed to solve the device diversity problem in crowdsourcing system. Since the spatial distribution of the APs is sparse, the Compressed Sensing (CS) method is applied to precisely estimate the location of the APs. Based on the location of the APs and a simple signal propagation model, the RSS difference between different locations is calculated and used as an additional constraint to improve the performance of G-SSL. Furthermore, to exploit the sparsity of the weights used in the G-SSL, we use the CS method to reconstruct these weights more accurately and make a further improvement on the performance of the G-SSL. Experimental results show improved results in terms of the smoothness of the radio map and the localization accuracy.

The effect of Al or Cu content on the microstructure and mechanical properties of continuous casting and extrusion Zn alloys has been studied by room temperature tensile test, X-ray diffraction, and scanning electron microscope. With the increase of Al content, the microstructure of continuous casting and extrusion Zn alloys slightly coarsens and the lamellar eutectic structure increases. The changes in the above structural factors result in a slight decrease in strength and a significant increase in elongation of Zn-Al alloys. The strength of Zn alloys increases as the Cu content increases, due to the increased content and size of the second phase in the Zn alloys. This means that the mechanical properties of Zn alloys can be adjusted by continuous casting and extrusion process, and the improvement of equipment capacity can improve the structure and morphology of the alloys.

a sensorless control scheme based on novel power converging law sliding mode observer is suggested to realize the sensorless control for the permanent magnet synchronous motor (PMSM). Firstly, by introducing a new power converging law, the problem of slow converging speed/large chattering value dilemma in the conventional converging law is solved; Secondly, in view of the shortcomings of the conventional position and speed estimation algorithm, the high-frequency buffeting in the sliding mode observer will be expanded, a phase-locked loop (PLL) velocity and position estimation strategy is adopted to replace it. Finally, through Matlab/Simulink modeling and motor speed regulation platform experimental results, the sensorless position and speed estimation technology proposed in this paper can respond to the starting speed command of 1000 r/min within 0.05 s, and the starting process has no overshoot. When disturbed by 10Nm loading, the speed fluctuation value can be controlled within 1%.

This paper proposes an analytical model of the double-stator spoke-type permanent-magnet vernier machine (DSSTVM) using the subdomain model (SDM), which can be used to calculate the mag-netic field distribution and corresponding electromagnetic parameters of the DSSTVM. The whole field domain is divided into several subdomains according to the magnetic characteristics of each region, within which Laplace's and Poisson's equations are solved accordingly in terms of magnetic vector potential (MVP). Then, the magnetic flux density distribution, back electromotive force (EMF), and electromagnetic torque of the DSSTVM can be obtained correspondingly. Ultimately, finite element analysis (FEA) is adopted to validate the proposed analytical model's effectiveness for quickly predicting the no-load and on-load performances of the DSSTVM.

Diamond-like carbon (DLC) films have a promising tribological application in green precision manufacturing, but their toughness represents a serious issue in the way of their application perspective. The film thickness is on the micrometer scale and makes conventional methods unsuitable for its toughness characterization. The absence of an accepted method for characterizing the DLC toughness has hindered the related research on the development of toughening methods and understanding the mechanism. This work intends to explore a relatively simple and acceptable characterization method to measure the film toughness. Moreover, toughening mechanisms of DLC films are proposed during the characterization to reveal the toughening mechanism. The toughness can be fully characterized through combining impact toughness and scratch toughness. The impact toughness can be obtained by observing the size of the indentation and the crack state around the indentation in the impact experiment. The scratch toughness could be assessed by combining the scratch morphology and Crack Propagation Resistance (CPRS). The improvement of film toughness should be carried out from two aspects: preventing microcrack initiation and suppressing crack propagation. Appropriate doping of non-carbide metal particles can effectively improve the toughness of the film, and there are seven main factors affecting the toughening of the film. Five toughening mechanisms of non-carbide metals from film preparation to test stage are revealed during the investigation of the change patterns.

With the rapid development of China's economy, construction industrialization has become the main development trend of China's construction industry, and the convenient, efficient, environmental protection has become the new fashion, therefore the application of prefabricated building is more and more common. Stair serves as the weak link in prefab type building, the connecting node has an important influence on its failure. In this paper, pseudo-static tests are carried out on the joints in different forms of ladder holes to study the mechanical properties of flexible hinge points filled with flexible materials, and the hysteresis curve, skeleton curve and bearing capacity of each specimen are analyzed. The test results show that the flexible hinge can give full play to its flexible characteristics to ease the stress of ladder beam, pin bolt reinforcement and ladder hole, and the bearing capacity of flexible hinge points is moderate, which can not only mitigate the inclined bracing effect under the action of small and medium earthquakes, but also ensure the stair does not fall off under the action of large earthquakes. Through the experiment comparison, the ladder hole adopts node form 2, which can give full play to the advantage of flexible material.

Aluminum (Al) toxicity is the most common factor limiting the growth of alfalfa in acidic soil conditions. Melatonin (MT), a significant pleiotropic molecule present in both plants and animals, has shown promise in mitigating Al toxicity in various plant species. This study aims to elucidate the underlying mechanism by which melatonin alleviates Al toxicity in alfalfa through a combined physiological and transcriptomic analysis. The results reveal that 5 μM MT significantly alleviates Al-induced growth inhibition and preserves the morphology of root tip cells. Moreover, MT application reduces Al accumulation in alfalfa roots and shoots by 28.6% and 27.6%, respectively. Additionally, MT plays a crucial role in scavenging Al-induced excess H2O2 by enhancing the activities of superoxide dismutase (SOD), peroxidase (POD), and catalase (CAT), consequently reducing malondialdehyde (MDA) levels. The RNA-seq results reveal that MT application significantly upregulates the expression of xyloglucan endotransglucosylase/hydrolase (XTH) and carbon metabolism-related genes, including those involved in the glycolysis process, as well as sucrose and starch metabolism, suggesting that MT application may mitigate Al toxicity by facilitating the binding of Al to the cell walls, thereby reducing intracellular Al accumulation, and by improving respiration and the content of sucrose and trehalose. Taken together, our study demonstrates that MT alleviates Al toxicity in alfalfa by restoring redox homeostasis, enhancing Al binding to the cell wall, and modulating carbon metabolism. This research advances our understanding of the mechanisms underlying MT's effectiveness in mitigating Al toxicity, offering potential strategies for reducing Al accumulation in alfalfa.

Autophagy is an evolutionarily conserved mechanism for degrading and recycling different cellular components in both normal development and stress conditions. Our recent research demonstrated that autophagy-mediated compartmental cytoplasmic deletion is essential for pollen germination. However, how autophagy regulates pollen germination to ensure its fertility remains largely unknown. Here, we applied multi-omic analyses to investigate the downstream pathways of autophagy in the process of pollen germination. Although ATG2 and ATG5 play similar roles in regulating pollen germination, high-throughput transcriptomic analysis reveals that silencing ATG5 has greater impact on the transcriptome than silencing ATG2. Cross-comparisons of transcriptome and proteome analysis reveal that gene expression at mRNA level and protein level are differentially affected by autophagy. Furthermore, high-throughput metabolomics analysis demonstrates that pathways related amino acid metabolism and aminoacyl-tRNA biosynthesis can be affected by both ATG2 and ATG5 silencing. Collectively, our multi-omic analyses reveal a central role of autophagy in cellular metabolism, which is critical for the initiation of pollen germination and the guarantee of pollen fertility.

New antimicrobial approaches are essential to counter antimicrobial resistance. The drug development pipeline is exhausted with emergence of resistance resulting in unsuccessful trials. The lack of an effective drug developed from the conventional drug portfolio has mandated the introspection into the list of potentially effective unconventional alternate antimicrobial molecules. Alternate therapies, that are clinically explicable forms include monoclonal antibodies, antimicrobial peptides, aptamers and phages. Clinical diagnostics optimizes the drug delivery. In the era of diagnostic-based applications, it is logical to draw diagnostic based treatment for infectious diseases. Selection criteria of alternate therapeutics in infectious disease include detection, monitoring of response and resistance mechanism identification. Integrating these diagnostic applications is disruptive to the traditional therapeutic development. The challenges and mitigation methods need to be noted. Applying the goals of clinical pharmacokinetics that include enhancing efficacy and decreasing toxicity of drug therapy this review analyses the strong correlation of alternate antimicrobial therapeutics in infectious diseases. The relationship between drug concentration and the resulting effect defined by the pharmacodynamic parameters are also analyzed. This review analyzes the perspectives of aligning diagnostic initiatives into the use of alternate therapeutics with a particular focus on companion diagnostic applications in infectious diseases.

This study presents a novel approach to analyzing the present value of total profit for non-participating and participating insurance policies in order to determine the optimal profitability of non-participating and participating insurance policies based on applying the approach used in operations research to the field of finance. As such, a comprehensive insurance product evaluation model was developed using both mathematical models and numerical analysis to evaluate the demand for non-participating and participating life insurance policies in response to changes in interest rates. The findings indicate that non-participating life insurance policies offer greater solvency for insurance companies compared to participating policies. The study also highlights the significance of spontaneous and induced demand in determining the total profit of both types of policies. The study concludes that life insurance companies should focus on generating spontaneous consumer demand, reducing induced demand, and implementing the optimal pricing strategy to achieve maximum profits.

Ce-promoted NiMgAl mixed-oxide (NiCex-C, x = 0, 1,5,10) catalysts were prepared from the quaternary hydrotalcite precursors for CO2 hydrogenation to methane. By engineering the Ce contents, NiCe5-C showed its prior catalytic performance in low-temperature CO2 hydrogenation, being about 3 times higher than that of Ce-free NiCe0-C catalyst (TOF of NiCe5-C and NiCe0-C: 1.19 h-1 vs 0.39 h-1 @ 250 oC). With extensive characterization, it was found that Ce dopants promoted the reduction of NiO by adjusting the interaction between Ni and Mg(Ce)AlOx support. The higest ratio of surface Ni0/(Ni2+Ni0) was obtained over NiCe5-C. Meanwhile, the surface basicity was tailored with Ce dopants. The strongest medium-strength basicity and highest capacity of CO2 adsorption was achieved on NiCe5-C with 5wt% Ce content. The TOF tests indicated a good correlation with medium-strength basicity over the NiCex-C samples. The results showed that the high medium-strength and Ce-promoted surface Ni0 species endows the enhanced low-temperature catalytic performance in CO2 hydrogenation to methane.

The APOE locus has garnered significant clinical interest because of its association with Alzheimer's disease (AD) and longevity. This genetic association appears across multiple genes in the APOE locus. Despite the apparent differences between AD and longevity, both conditions share a commonality of aging-related changes in mitochondrial function. This commonality is likely due to accumulative biological effects, partly exerted by the APOE locus. In this study, we investigated changes in mitochondrial structure/function-related markers using oxidative stress-induced human cellular models and postmortem brains (PMBs) from individuals with AD and normal controls. Our results reveal a range of expressional alterations, either up- or down-regulated, in these genes in response to oxidative stress. In contrast, we consistently observed an upregulation of multiple APOE locus genes in all cellular models and AD PMBs. Additionally, the effects of AD status on mitochondrial DNA copy number (mtDNA CN) varied depending on APOE genotype. Our findings imply a potential coregulation of APOE locus genes, possibly occurring within the same topologically associating domain (TAD) of the 3D chromosome conformation. The coordinated expression of APOE locus genes could impact mitochondrial function, contributing to the development of AD or longevity. Our study underscores the significant role of the APOE locus in modulating mitochondrial function and provides valuable insights into the underlying mechanisms of AD and aging, emphasizing the importance of this locus in clinical research.

Physical activity is well-established as an important protective factor against degenerative conditions and a promoter of tissue growth and renewal. The discovery of FNDC5 as the precursor of irisin in 2012 sparked significant interest in its potential as a diagnostic biomarker and a therapeutic agent for various diseases. Clinical studies have examined the correlation between plasma irisin levels and pathological conditions using a range of assays, but the lack of reliable measurements for endogenous irisin has led to uncertainty about its prognostic/diagnostic potential as an exercise surrogate. Animal and tissue-engineering models have shown the protective effects of irisin treatment in reversing functional impairment and potentially permanent damage, but dosage ambiguities remain unresolved. This review provides a comprehensive examination of the clinical and basic studies of irisin in the context of degenerative conditions and explores its potential as a therapeutic approach in the physiological processes involved in tissue repair/regeneration.

Objective: To explore the efficacy and safety of breathing exercises for pain management in cancer survivors. Design: A systematic review. Data sources: Thirteen databases, including PubMed, EMBase, CENTRAL, Medline, CINAHL, JBI, Science Direct, Scopus, SocINDEX, Web of Science, PsycINFO, CNKI, and Wan Fang, were searched from inception to May 24, 2021. Review/analysis methods: Studies that focused on the efficacy of breathing exercises for pain management in cancer survivors were included. Cochrane tools were used for the quality appraisal of the included studies. Due to the heterogeneity of the studies, descriptive data analysis was used to summarize the results. Results: A total of 10 studies were included in this systematic review. Slow pursed lip breathing showed benefits for post-surgical pain. Contradictory findings were identified in the Enhanced Recovery After Surgery breathing exercise for post-surgical pain. Slow deep breathing and Hey-Hu regular breathing techniques were effective for pain management in pediatric cancer patients. The Active Cycle of Breathing Technique and five-minute mindful breathing did not have any statistically significant effects on pain relief. Quality of life was measured in three studies, with some improvement. Only one study addressed adverse events and reported that no adverse events associated with the breathing exercises occurred during the study. Conclusion: This review found some evidence of positive effects of breathing exercises for pain relief in cancer survivors. However, the unsatisfactory methodological quality of the studies prevents its generalizability. More large-scale studies are needed to assess the efficacy and safety of breathing exercises for pain relief in cancer survivors.

Peri-implantitis occurs at a significant rate, which is the leading cause of implant failure. The main reason for this unwanted complication is bacterial invasion and biofilm formation. To reduce the incidence of peri-implantitis, we constructed a carboxymethyl dextran (CMD) based nanomicelles antibacterial coating on microarc-oxidized titanium (MAO-Ti) surface. After cross-linking, the drug-loaded nanomicelles were spherical with a particle size of 130nm and uniformly dispersed. Zeta potential was negative, and the absolute value was greater than 10 mV, effectively avoiding micelles aggregation. It was observed by dynamic light scattering (DLS) that the stability of nanomicelles was significantly improved after cross-linking. The hemolysis rate of micelles was less than 5%, and the overall survival rate of human umbilical vein endothelial cells was more than 90%. After being coated on MAO-Ti surface, the cumulative drug release rate of drug-loaded nanomicelles reached 86.6% after 360 hours. Fluorescence staining of immobilized bacteria showed more dead bacteria on the coating surface, and the number of live bacteria was significantly reduced. It was concluded that dextran-based nanomicelles, which showed long-term drug release properties and excellent biocompatibility, are potential drug carriers for fabricating antibacterial coating on titanium surfaces.

Panchromatic (PAN) images contain abundant spatial information that is useful for earth observation, but always suffer from low-resolution due to the sensor limitation and large-scale view field. The current super-resolution (SR) methods based on traditional attention mechanism have shown remarkable advantages but remain imperfect to reconstruct the edge details of SR images. To address this problem, an improved super-resolution model which involves the self-attention augmented WGAN is designed to dig out the reference information among multiple features for detail enhancement. We use an encoder-decoder network followed by a fully convolutional network (FCN) as the backbone to extract multi-scale features and reconstruct the HR results. To exploit the relevance between multi-layer feature maps, we first integrate a convolutional block attention module (CBAM) into each skip-connection of the encoder-decoder subnet, generating weighted maps to enhance both channel-wise and spatial-wise feature representation automatically. Besides, considering that the HR results and LR inputs are highly similar in structure, yet cannot be fully reflected in traditional attention mechanism, we therefore design a self augmented attention (SAA) module, where the attention weights are produced dynamically via a similarity function between hidden features, this design allows the network to flexibly adjust the fraction relevance among multi-layer features and keep the long-range inter information, which is helpful to preserve details. In addition, the pixel-wise loss is combined with perceptual and gradient loss to achieve comprehensive supervision. Experiments on benchmark datasets demonstrate that the proposed method outperforms other SR methods in terms of both objective evaluation and visual effect.

Arylsulfatase and β-glucuronidase are two important enzymes in human, which play important role on dynamic equilibrium of steroidal estrogens. This work probably for the first time reported that hydrogen peroxide (H2O2), hypochlorite and peracetic acid (PAA) could effectively inhibit the activities of arylsulfatase and/or β-glucuronidase. The 50 percent of inhibitions (IC50) of H2O2, and PAA on arylsulfatase were found to be 142.90±9.00, 91.83±10.01, and 43.46±2.92 μM, respectively. The corresponding respective IC50 of hypochlorite and PAA on β-glucuronidase were 704.90±41.40 and 23.26±0.82 μM, while H2O2 showed no inhibition on β-glucuronidase. It was further revealed that the inhibition of hypochlorite on both arylsulfatase and β-glucuronidase was irreversible. On the contrary, the inhibition by H2O2 and PAA was reversible. Moreover, it was found that the inhibitions of arylsulfatase and/or β-glucuronidase by these three chemicals were pH-dependent, among which the inhibition by H2O2 was competitive and non-competitive for PAA. In general, H2O2 and hypochlorite can be endogenously produced in human, which suggested that the two compounds are potential endocrine disruption compounds (EDCs) as they can cause endocrine disruption via inhibition of arylsulfatase and β-glucuronidase. This work further indicated that any agent that can induce production of H2O2 or hypochlorite in human is potential EDC, which explains why some EDCs with very weak or no estrogenic potency can cause endocrine disruption that confirmed in epidemiological studies.

The gut microbiota has been suggested as an important factor in the pathogenic mechanisms of amyotrophic lateral sclerosis (ALS). This study aimed to investigate whether the intake of different kinds of dietary fiber was related to the disease progression rate (∆FS) and survival time. In total, 272 sporadic ALS patients diagnosed according to the revised EI Escorial criteria were recruited from March 2011 and were followed-up until the occurrence of events or the end of September 2020. The events included percutaneous endoscopic gastrostomy, tracheostomy, and death. Dietary fiber intake was calculated based on a 24-hour dietary recall and classified according to five major fiber-rich foods: vegetables, fruits, grains, legumes, and nuts/seeds. Among the total participants, the group with ∆FS values lower than the mean ∆FS (0.75) was noted in the highest tertiles of total and vegetable fiber intake. Participants with the highest tertile of vegetable fiber intake showed longer survival in the Kaplan–Meier analysis (p = 0.033). Notably, vegetable fiber intake was negatively correlated with pro-inflammatory cytokine (interleukin [IL]-1β, IL-6, and monocyte chemoattractant protein-1) levels in the cerebrospinal fluid. This study showed that vegetable fiber intake could influence the disease progression rate and survival time. Further clinical trials are needed to confirm whether dietary fiber supplementation improves the prognosis of ALS.

Background: Wheat root rot disease due to soil-borne fungal pathogens leads to tremendous yield losses worth billions of dollars worldwide every year. It is very important to study the relationship between rhizosphere fungal diversity and wheat roots to understand the occurrence and development of wheat root rot disease. Results: A significant difference in fungal diversity was observed between the diseased and healthy groups in the heading stage, but the trend was the opposite in the filling stage. The abundance of most genera with high richness decreased significantly from the heading to the filling stage in the diseased groups; the richness of approximately one-third of all genera remained unchanged, and only a few low-richness genera, such as Fusarium and Ceratobasidium, had a very significant increase from the heading to the filling stage. In the healthy groups, the abundance of most genera increased significantly from the heading to the filling stage; the abundance of some genera did not change markedly, or the abundance of very few genera increased significantly. Physical and chemical soil indicators showed that low soil pH and density, increases in ammonium nitrogen, nitrate nitrogen and total nitrogen contributed to the occurrence of wheat root rot disease. Conclusions: Our results revealed that in the early stages of disease, highly diverse rhizosphere fungi and a complex community structure can easily cause wheat root rot disease. The existence of pathogenic fungi is a necessary condition for wheat root rot disease, but the richness of pathogenic fungi is not necessarily important. The increases in ammonium nitrogen, nitrate nitrogen and total nitrogen contributed to the occurrence of wheat root rot disease. Low soil pH and soil density are beneficial to the occurrence of wheat root rot disease.

To explore the characteristics of the concentric eyewall of a typhoon during its formation and replacement processes, with Super Typhoon Muifa in 2011 as the example case, the Weather Research and Forecast (WRF) mode was used to carry out a numerical simulation to reproduce the entire formation and replacement processes of the concentric eyewall. The physical quantities such as the tangential wind speed, radar echo, radial wind speed, vertical wind speed, and potential vortex were diagnosed and analyzed. The results of the analysis show that the outward expansion of the isovelocity in the lower troposphere was the early signal of the formation of the outer eyewall. After the outer eyewall formed, there was a center of second-highest tangential wind speed in the corresponding area. The second-highest wind speed increased as the strength of the outer eyewall increased, and the position of the second-highest wind speed center was retracted with the retraction of the outer eyewall. The tangential wind speed of the moat area was smaller than that corresponding to the concentric eyewall and this feature gradually disappeared with the increase of the height. The echo in the moat area was weak, and this characteristic was particularly evident when the moat area was relatively wide and the outer eyewall was relatively strong. With the formation and development of the outer eyewall, the intensity of the inflow in the boundary layer corresponding to the inner eyewall was reduced, the intensity of the outflow in the upper layers declined, and the intensities of the inflow and outflow corresponding to the outer eyewall were enhanced. After the second outer eyewall matured, there was a significant inflow in the upper layer of the moat area. Once the outer eyewall formed, a large amount of hydrometeors appeared in the corresponding area, and there was a strong ascending motion inside that area. The strength of the ascending motion and the content of hydrometeors increased as the outer eyewall increased. When the moat area was relatively wide, the divergent airflow generated by the developed outer eyewall in the upper layer would produce a significant descending motion in the moat area.

The characteristics of biogenic aerosols in urban area were explored by determining the composition, temporal distribution of saccharides in PM_2.5 in Shanghai. The total saccharides showed a wide range of 15.2 ng/m³ to 1752.8 ng/m³, with the averaged concentrations were 169.8 ng/m³，300.5 ng/m³，288.4 ng/m³，688 ng/m³ in spring, summer, autumn, and winter, respectively. The concerned saccharides include anhydrosaccharides (levoglucosan and mannosan), which were higher in cold seasons due to the increased biomass burning, saccharide alcohols (mannitol, arabitol, sorbitol) and monosaccharides (fructose, glucose), which showed more abundant in warm seasons attributed to the biological emissions. By PMF analysis, four emission sources of saccharides were demonstrated, including biomass burning, fungal spores, soil suspension and plant pollens. Resolution of backward trajectory and fire points showed a process of high concentrations of levoglucosan. We found that concentrations of anhydrosaccharides showed relatively stable under different pollution levels while saccharide alcohols exhibited an obvious decrease, indicated that biomass burning was not the core reason of the heavy haze pollution, however, and high level PM_2.5 pollution might inhibit effects of biological activities.

Foxtail millet (Setaria italica) is an important cereal crop with rich nutritional value. Distinctness, Uniformity, and Stability (DUS) are the prerequisites for the application of new variety rights for foxtail millet. In this study, we investigated 32 DUS test characteristics of 183 foxtail millet resources, studied their artificial selection trends, and identified varieties that conform to breeding trends. The results indicated significant differences in terms of means, ranges, and coefficients of variation for each characteristic. Correlation analysis was performed to determine the correlations between various DUS characteristics. Principal component analysis was conducted on 31 test characteristics to determine their primary characteristics. By plotting PC1 and PC2, all germplasm resources could be clearly distinguished. Trends in foxtail millet breeding were identified through differential analysis of DUS test characteristics between landrace varieties and cultivated varieties. Based on these breeding trends, optimal solution types for multiple evaluation indicators were determined; weight allocation was calculated, and a specific TOPSIS algorithm was designed to establish a comprehensive multi-criteria decision-making model. Using this model, the breeding potential of foxtail millet germplasm resources was ranked. These findings provided important reference for foxtail millet breeding in future.

Antibiotic-loaded bone cement (ALBC) plays a pivotal role in infection prevention and treatment related to musculoskeletal surgery. The release efficacy of antibiotics from ALBC is closely tied to its surface area, yet little is known about the effective release depth. To investigate the relationship between surface area, volume, and antibiotic elution, spheric ALBC specimens with consistent outer diameters but different internal metal sphere diameters were prepared. Two vancomycin doses were utilized in ALBC specimens with an outer diameter of 35 mm: high (4 g) and low (1 g). Each dosage group included five specimens containing embedded metal spheres with diameters of 15, 25, 29, 32, or 33 mm. The resulting shell-like ALBC specimens had thicknesses of 10 mm, 5 mm, 3 mm, 1.5 mm, or 1 mm, respectively. The specimens were immersed in sterile phosphate buffer solution, and antibiotic elution was measured at designated sampling times (1, 3, 6, 10, 24, 48, 72, and 168 hours). Methylene blue was employed to visualize penetration depth. Vancomycin elution did not display statistically significant differences between high- and low-dose groups. In both groups, specimens with 1 mm thickness exhibited a higher vancomycin release efficiency (high-dose group: 18560±5474 μg, 6.7%; low-dose group: 2017±419 μg, 2.6%), decreasing sharply in thicker ALBC specimens. Methylene blue penetration depth showed no apparent difference between high-dose and low-dose groups. ALBC thickness does not significantly impact antibiotic elution, while surface area and antibiotic dose exert notable effects. These in vitro findings offer potential applications in clinical treatments for musculoskeletal infections.

Autism spectrum disorder (ASD) is a complex neurodevelopmental disorder with heterogeneous and complex genetic underpinnings. Our previous microarray gene-expressed profiling identified significantly different neuregulin-2 (NRG2) gene expressions between ASD patients and controls. Thus, we aimed to clarify whether NRG2 is a candidate gene associated with ASD. The study consisted of two stages. First, we used real-time quantitative PCR in 20 ASDs and 20 controls to confirm the microarray gene expression profiling results. The average NRG2 gene expression level in patients with ASD (3.23±2.80) was significantly lower than that of controls (9.27±4.78, p < 0.001). Next, we resequenced all exons of NRG2 in other 349 ASD subjects, who were compared with super-controls from the Taiwan Biobank using case-control association analysis to determine the existence of mutations or single-nucleotide polymorphisms (SNPs). We identified three SNPs, including two noncoding ones, IVS3 + 13A > G (rs889022) and IVS9 + 32T > A (rs182642591), and one insertion/deletion (indel) SNP, named indel GCCCGGC, rs1323957797, in the NRG2 coding region. The genotype and allele frequency distribution of rs1323957797 significantly differed between ASDs and controls (p < 0.0001). Our findings showed significant differences in genotype and allele frequency distribution of the indel SNP, rs1323957797, located in the EGF-like domain region at the C-terminal of the NRG2 precursor protein. Together with our findings, the indel SNP mutation was significantly more common in ASDs than controls, leading to lower NRG2 expression than controls, influencing NRG2 function. Our study’s findings suggest that NRG2 is a susceptibility gene for ASD.

Apple latent spherical virus (ALSV) is widely used as a virus-induced gene silencing (VIGS) vector for function genome study. However, the application of ALSV in soybean is limited by the resistance of many varieties. In this study, the genetic loci linked to the resistance of a resistant soybean variety Heinong 84 was mapped by high-throughput sequencing‒Bulk Segregation Analysis (HTS‒BSA) using a hybrid population crossed from Heinong 84 and a susceptible variety Zhonghuang 13. Results showed that the resistance of Heinong 84 to ALSV is controlled by two genetic loci located on chromosome 2 and 11, respectively. Cleaved amplified polymorphic sequences (CAPS) markers were developed for identification and genotyping. Inheritance and biochemical analyses suggest that the resistance locus on chromosome 2 plays a dominant dose-dependent role, while the other locus contributes a secondary role in resisting ALSV. The resistance locus on chromosome 2 might encode a protein that can directly inhibit viral proliferation, while the secondary resistance locus on chromosome 11 may encode a host factor required for viral proliferation. Together, these data reveal novel insights on the resistance mechanism of Heinong 84 to ALSV, which will benefit for the application of ALSV as a VIGS vector.

One new cassane diterpene possessing an unusual N bridge between C-19 and C-20 named caesalsappanin R (1), as well as another new diterpene caesalsappanin S (2), were isolated from the seeds of Caesalpinia sappan with methanol extract. Their structures were determined by spectroscopic analysis and examined alongside existing data from prior studies. Their biological activities were profiled by their antiplasmodial activity.

This paper aims to develop a hierarchical risk assessment model using the newly-developed evidential reasoning (ER) rule, which constitutes a generic conjunctive probabilistic reasoning process. In this paper, we first provide a brief introduction to the basics of the ER rule and emphasize the strengths for representing and aggregating uncertain information from multiple experts and sources. Further, we discuss the key steps of developing the hierarchical risk assessment framework systematically, including (1) formulation of risk assessment hierarchy, (2) representation of both qualitative and quantitative information, (3) elicitation of attribute weights and information reliabilities, (4) aggregation of assessment information using the ER rule and (5) quantification and ranking of risks using utility-based transformation. The proposed hierarchical risk assessment framework can potentially be implemented to various complex and uncertain systems. A case study on the fire/explosion risk assessment of marine vessels demonstrates the applicability of the proposed risk assessment model.

A dynamic impact test was performed on as-rolled AZ31 alloy with gradient microstructure under various strains. The microstructural evolution and mechanical properties were systematically investigated. As the strain rate gradually increases, an increasing number of twins are formed, facilitating dynamic recrystallization (DRX), and the mechanical properties are also gradually improved as well. The microstructure becomes heterogeneous at higher strain rates, but the peak stress decreases. The impact process results in significantly higher performance due to microstructural refinement, work hardening by dislocations and precipitates. In addition, both the adiabatic shear band and the adjacent crack experience a temperature rise that exceeds the recrystallization temperature of the alloy. This observation also explains the presence of ultrafine recrystallized grains within the adiabatic shear band and the appearance of molten metal around the crack.

The capacitated multi-item lot-sizing problem abbreviated as CLSP, is to determine the lot sizes of products in each period in a given planning horizon of finite periods meeting the product demand and resource limits in each period, and minimize the total cost consisting of production, inventory holding, and setup costs. CLSPs are often encountered in industry production settings and thus the solution is significant. In this paper, we propose a Lagrange relaxation (LR) approach for the solution of its. The approach decomposes the CLSP into several uncapacitated single-item lot-sizing problems each of which can be easily solved by dynamic programming. The feasible solutions are achieved by solving the resulting transportation problems with a proposed stepping-stone algorithm and a fix-up procedure. The Lagrange multipliers are updated by using subgradient optimization. Experimental results show that the LR approach explores high-quality solutions and has better applicability compared with other commonly used solution approaches in the literature.

Reactions of N‚N'-bis(3-methylpyridyl)oxalamide (L1), N,N’-bis(3-methylpyridyl)adipoamide (L2) and N,N’-bis(3-methylpyridyl)sebacoamide (L3) with tricarboxylic acids and Cu(II) salts afforded {[Cu(L1)(1,3,5-HBTC)]·H2O}n (1,3,5-H3BTC = 1,3,5-benzenetricarboxylic acid), 1, {[Cu1.5(L2)1.5(1,3,5-BTC)(H2O)2]·6.5H2O}n, 2, [Cu(L2)0.5(1,3,5-HBTB)]n (1,3,5-H3BTB = 1,3,5-tri(4-carboxyphenyl)benzene), 3, [Cu4(L3)(OH)2(1,3,5-BTC)2]n, 4, {[Cu3(L3)2(1,3,5-BTB)2]·2.5MeOH·2H2O}n, 5, and {[Cu3(L3)2(1,3,5-BTB)2 ]·DMF·2H2O}n, 6, which have been structurally characterized by using single crystal X-ray crystallography. Complexes 1 – 4 form a 2D layer with the {44.62}-sql topology, a 2D layer with the (4.62)2(42.62.82)-bex topology, a 3-fold interpenetrated 3D net with the (412.63)-pcu topology and a 3D framework with the (410.632.83)(42.6)2(43.63) topology, respectively, whereas 5 and 6 are 3D frameworks with the (63)2(64.82)(68.85.102) topology. Complex 5 shows a better iodine-adsorption factor of 290.0 mg g-1 at 60 oC for 360 minutes than the other ones, revealing that the flexibility of the spacer ligand governs the structural diversity and the adsorption capacity.

In this paper, the overall performance of Cu-(In,Ga)-Se₂ (CIGSe) solar cells was improved in the ultraviolet (UV)–visible wavelength region by two-segment process. In which, adjusting DC sputtering powers (20–40 W) for absorbers (segment I), and metal-alloy compositions (CdS, ZnO/CdS, ZnMgO/CdS and ZnMgO) for buffers (segment II) were explored and characterized. Upon choosing the optimal-30-W CIGSe-absorber (with 0.95-CGI ratio) sputtered by the segment-I process, the Cu-rich film can distinctly boost grain growth, thus reducing the trap state density. After segment-II process as the toxic-CdS alternative, the optimal Zn_0.9Mg_0.1O-alloy buffer can reach the best conversion efficiency (η = 8.70%) was attained for the environmental protection. Meanwhile, and the overall internal/external quantum efficiencies (IQE/EQE) were improved by 13.15%, respectively for the 2.48–3.62-eV bandgap (short wavelength) range. The developed photovoltaic (PV) module (with 9 optimum-CIGSe cells) exhibits acceptable stability with a variance within ±5% over the 60-day experiment. This discovery in PV-device research contributes to a new scientific understanding of renewable energy. Furthermore, this study undeniably enhances the progress of practical applications for PV-modules in alignment with sustainable development goals. It also actively supports the development of eco-friendly communities.

A millimeter-wave microstrip leaky-wave antenna array based on the substrate-integrated waveguide (SIW) and the complementary split-ring resonator (CSRR) is proposed in this paper. The slow wave characteristics of the SIW are enhanced by etching two rows of symmetrical CSRR-type slots on the surface of the SIW layer. The magnetic coupling between the CSRR-SIW layer and equally spaced circular patches array on the upper layer realizes the radiation of electromagnetic energy. In the 23~30 GHz (relative bandwidth 26.4%) operating frequency band, the horizontal polarization radiation beam scanning from -62° to -2° is realized, with a peak gain of 9.6~11.7 dBi, and the cross-polarization ratio is more than 43.8 dB.

Bioactive lipids are involved in cellular signalling events with links to human disease. Many of these are involved in inflammation under normal and pathological conditions. Despite being attractive molecules from a pharmacological point of view, detection and quantification of lipids has been a major challenge. Here, we have optimised a liquid chromatography dynamic multiple reaction monitoring targeted mass spectrometry (LC-dMRM-MS) approach to profile eicosanoids and fatty acids in biological samples. In particular, by applying this analytic workflow to study a cellular model of Chronic Myeloid Leukaemia (CML), we found that intra- and extra-cellular 2-Arachidonoylglycerol (2-AG), intracellular Arachidonic Acid (AA), and extracellular Prostaglandin F_2α (PGF_2α), 5-Hydroxyeicosatetraenoic acid (5-HETE), Palmitic acid (PA, C16:0) and Stearic acid (SA, C18:0) were altered in response to immunomodulation by type I Interferon (IFN-I), a currently approved treatment for CML. Our observations indicate changes in eicosanoid and fatty acid metabolism with potential relevance in the context of cancer inflammation and CML.

(1) Background: To identify the association between the presence or absence of raphe and aortic valve dysfunction as well as the presence of aortopathy in patients with bicuspid aortic valve (BAV); (2) Methods: This retrospective study enrolled 312 participants (mean [SD] age, 52.7 [14.3] years; 227 men [72.8%]) with BAV. The BAVs were divided into those with presence (raphe+) or absence (raphe-) of raphe. Valvular function was classified as normal, aortic regurgitation (AR), or aortic stenosis (AS) using TTE. The pattern of BAV aortopathy was determined by the presence of dilatation at the sinus of Valsalva and the middle ascending aorta using CCT.; (3) Results: BAVs with raphe+ had a higher prevalence of AR (148 [79.5%] vs. 48 [37.8%], P < .001) but a lower prevalence of AS (90 [48.6%] vs. 99 [78.0%], P < .001) compared with those with raphe-. The types of BAV aortopathy were significantly different (P = 0.021) according to those with BAV-raphe+ and BAV-raphe-.; (4) Conclusions: The presence of a raphe was significantly associated with a higher prevalence of AR but a lower prevalence of AS and combined dilatation of the aortic root and middle ascending aorta. The presence of raphe was an independent determinant of AR.

Health issues of children with intellectual disabilities (ID) have gained significant attention as a key focus of China health goals. This study aimed to compare the differences in displacement skills and problem behaviors among children with varying degrees and types of ID, while also exploring their relationship. The study included 90 participants who were children with ID and had completed TGMD-2 displacement skills and Strengths and Difficulties Questionnaire (SDQ) assessments. Covariance, partial correlation, and multiple linear regression analyses were conducted to examine the differences and correlations between these factors. The findings revealed that higher severity of intellectual disability was associated with lower scores in locomotor skills and increased manifestation of problem behaviors. Notably, there were significant variations in locomotor skills and problem behaviors among children with different types of intellectual disabilities. There is a positive correlation between locomotor skills and problem behaviors in children with intellectual disabilities, where locomotor skills can predict the occurrence of problem behaviors. In Conclusion, the research confirms that the development of locomotor skills can have a positive impact on the accompanying problem behaviors of children with developmental disabilities.

Multi-chiplet technique is expected to be a promising solution to achieve high-density system integration with low power consumption and high usage ratio. This technique can be integrated with glass interposer to accomplish a competitive low fabrication cost compared with the silicon-based interposer architecture. In this study, process-oriented stress simulation is performed by the element activation and de activation technique in finite element analysis architecture. Submodeling technique is also utilized to mainly conquer the scale mismatch and difficulty in mesh gridding design. It is used as well to analyze the thermomechanical responses of glass interposer with chiplet arrangement and capped epoxy molding compound (EMC) during curing. A three-factor, three-level full factorial design is applied using the analysis of variance method to explore the significance of various structural design parameters on stress generation. Analytic results reveal that the maximum first principal stresses of 130.75 and 17.18 MPa are introduced on the sidewall of Cu-filled via and the bottom of glass interposer, respectively. Moreover, the EMC thickness and through glass via pitch are the dominant factors in the adopted vehicle. They significantly influence the stress magnitude during heating and cooling.

pH is the major factor that makes producers in aquaponics frustrated, since the main three organisms (aquatic animal, plant, and microbes) in the system with different preferences. Yet, amending the growing environment with additional C is a potential method to improve the growth of shrimp and plants as well as the establishment of microbe. A detailed study of the effects of pH and additional C on aquaponics under saline conditions has not been investigated. In this study, the effect of pH and additional C on the growth performance of shrimp (Litopenaeus vannamei) and five edible plants in marine aquaponic systems using the nutrient film technique (NFT) was evaluated. The results indicated that at both pH 6.5 treatments, plants grew better; nevertheless, the growth performance of plants in pH 7.5 with additional C was improved and showed a similar yield to lower pH treatments. On the other hand, shrimp growth was little affected by pH and additional C. A higher impact of imbalanced ionic composition on shrimp performance may have contributed to this trend. Hence, we suggest that only if the ionic composition is managed can make RO water a suitable source of water for shrimp-based aquaponic. In spite of this, more research is required.

The bilateral trade relationship between PRC and ASEAN is close. As early as 2012, China has been the largest trading partner of ASEAN, and ASEAN has also taken the place of the United States as PRC’s second largest trading partner in 2019.This paper uses the theory of ecological population evolution, selects the total import and export volume of PRC and the ten ASEAN countries from 2000 to 2019 as the data sample, studies the bilateral trade relations between PRC and the ten ASEAN countries, analyzes the competition and symbiotic relationship of bilateral trade between PRC and the ten ASEAN countries and the possibility of trade friction according to the results, and proposes corresponding improvement strategies. According to the results of the population evolution competition model, China has a competitive relationship with Indonesia, Malaysia, the Philippines, Singapore and Thailand, which is most likely to cause trade friction. China has a biased relationship with Brunei, Cambodia, Laos, Myanmar and Vietnam, which is more likely to cause trade friction. On this basis, in order to further strengthen the trade relations between PRC and the ten ASEAN countries, this paper puts forward policy suggestions on improving infrastructure, strengthening independent innovation, seeking cooperation fields and actively investing abroad.

Tillage has been reported to induce seasonal changes of organic carbon (Сmicro) and nitrogen (Nmicro) in biomass of microorganisms. Soil microorganisms execute such ecosystem functions as: it is an immediate sink of labile biophil elements; it is an agent of a conversion, catalysis and synthesis of humus substances; it transforms soil contaminants into non-hazardous wastes; it participates in soil aggregation and pedogenesis as a whole. However, the seasonal turnover of microorganisms on arable lands in temperate ecosystems has not been investigated on a relevant level. Hence, we aimed to study the dynamics of such soil microbial biomass patterns as: Сmicro, Nmicro, microbial index (MI = (Сmicro/CTOC)·100, %) and CO2-C emission on the background of 9 years of tillage and 22 years of abandoned (Ab) and fallow (F) usage. Our study was conducted on a long-term experimental site on a Mollisol in the northeast China. The maximum Сmicro and Nmicro content was found: at the beginning of the growing season – in 0-10-; in mid-July – in 20-40 cm layers, while the minimum – in August-October. The Сmicro content ranged from 577.79- and 381.79 mg-1 kg-1 under Ab in spring to 229.53- and 272.86 mg-1 kg-1 in autumn under CT (conventional tillage) and F in 0-10- and 10-20 cm layers, respectively. The amplitude of Nmicro content changes was several times lower comparatively to Сmicro. The smallest quartile range (IQR0.25-0.75) of such changes was under: no-till (NT) and Ab in 0-10-, NT and F – in 10-20- and CT - in 20-40 cm layers. The widest Сmicro : Nmicro ratio was found at F and CT – in 0-20- and CT and rotational tillage (Rot) – in 20-40 cm layers. MI dynamics resembled the trends of Сmicro and Nmicro and changed from 0.72  0.168- tо 2.00  0,030 %. The highest part of Сmicro in CTOC was at Ab (1.82  1.85 %) and NT (1.66  1.52 %) – in 0-10-; Ab (1.23  1.27 %) and NT (1.29  1.32 %) – in 10-20- and – Ab (1.19  1.09 %) and F (1.11  1.077 %) – in 20-40 cm layers, correspondingly. The Pearson’s correlation coefficient between Сmicro and CTOC increased from the upper 0-10- to the lower 20-40 cm layer, it was "strong" and "high" between Сmicro and CTOC. Different use of Mollisol affected the amplitude of Сmicro and Nmicro seasonal changes, but it didn’t change their trend. Our results suggest the key role of Ab and NT technologies in Сmicro accumulation in total organic carbon (TOC).

Conclusions: Molecular classification could provide reliable supplementary information for evaluating prognostic and contribute to treatment option decision-making in EEC patients. Fertility-sparing treatment is not recommended for EEC patients with CNH and MSI-H. Furthermore, fertility-sparing treatment can be attempted in EEC patients with CHL, but regular follow-up should be carried out to early detection of EC relapse and prevention of disease progression.

Feruloylacetone (FER) is a natural degradant of curcumin after heating, which structurally reserves some functional groups of curcumin. It is not as widely discussed as its original counterpart in previous studies and, therefore, its anti-cancer efficacy is investigated herein. This study focuses on the suppressive effect of FER on colon cancer, as the efficacious effect of curcumin on this typical cancer type has been well evidenced. In addition, demethoxy-feruloylacetone (DFER) was applied to compare the effect that might be brought on by the structural differences of the methoxy group. It was revealed that both FER and DFER inhibited the proliferation of HCT116 cells, possibly via suppression of the phosphorylated mTOR/STAT3 pathway. Notably, FER could significantly repress both the STAT3 phosphorylation and protein levels. Furthermore, both samples showed the capability of arresting HCT116 cells at the G2/M phase via the activation of p53/p21 and upregulation of cyclin-B. In addition, ROS elevation and changes in mitochondrial membrane potential were revealed, as indicated by p-atm elevation. The apoptotic rate rised to 36.9% and 32.2% after being treated by FER and DFER, respectively. In summary, both compounds exhibited an anti-cancer effect, and FER showed a greater pro-apoptotic effect, possibly due to the presence of the methoxy group on the aromatic ring.