Bi0.5Na0.5TiO3-0.06BaTiO3 (BNT-BT) thin films were prepared by both chemical solution (CSD) and pulsed laser deposition (PLD). The microstructure, dielectric, and ferroelectric properties were investigated. High stability of the dielectric permittivity (∆ɛ/ɛ(150 °C) ≤ ± 15%) over a wide temperature range from room temperature to 300 °C was obtained. Distinctly, the CSD film showed high TCC stability with variation of ± 5% up to 250°C. Furthermore, the CSD film showed an unsaturated ferroelectric hysteresis loop characteristic of the ergodic relaxor phase, however the PLD one exhibited almost saturated loop signature of the coexistence of both ergodic and non-ergodic states. The energy storage properties of the prepared films were determined using the P–E loops obtained at different temperatures. The results showed that these films exhibit stable and improved energy storage density comparable to the ceramic capacitors. Moreover, the CSD film exhibited more rigidity and better energy storage density that exceeds 1.3 J/cm3 under low applied field of 317 KV/cm as well as interesting efficiency in a large temperature range. The obtained results are very promising for energy storage capacitors operating at high temperatures.

Turbulence is a fluid dynamic problem refractory to mathematical treatment. Examining a theoretical model of liquid water flowing in a cylinder at different Raleigh numbers, we propose a novel approach to elucidate the first stages of turbulent flows. The weakly bonded molecular assemblies of liquid water form a fluctuating branched polymer in which every micro-cluster displays different density. Against the common view of liquid water as an incompressible and continuous fluid, we suggest that the occurrence of transient local aggregates could be able to generate the vortices and eddies that are the hallmarks of turbulence. We quantify the local changes in velocity, diameter and density required to engender “obstacles” to the average flow. Then, we show how these microstructures, equipped with different Raleigh numbers and characterized by high percolation index, could generate boundary layers that contribute to micro-vortices production. We conclude that the genesis of turbulence cannot be assessed in terms of collective phenomena, rather is sustained, among many other factors, by the underrated microscopic inhomogeneities of fluids like liquid water.

In recent years, green and healthy foods have attracted much attention. Plant-based foods have become a new trend to replace animal-derived foods. In this study, we used walnut and purple rice as the primary raw materials to produce yogurt. The process included boiling, mixing, grinding, inoculation, fermentation, and sterilization. We then analyzed the similarities and differences between the resulting walnut purple rice yogurt and unfermented walnut purple rice milk, as well as dairy-based yogurt, in terms of physical chemistry, flavor, and sensory characteristics. We also examined the similarities and differences between fermented walnut purple rice milk and conventional warm yogurt. The study results revealed that walnut purple rice yogurt exhibited greater viscosity than walnut purple rice milk and conventional dairy-based yogurt. Additionally, the former displayed enhanced stability and recovery ability. Notably, distinguishable differences were observed between the three types of yogurts in terms of the presence of unknown volatiles and the umami signal as indicated by electronic nose/tongue and GC-IMS analyses. The umami flavour of walnut purple rice yogurt surpasses that of traditional dairy-based yogurt, whilst its salty taste is lower than that of walnut purple rice milk. Despite possessing a weaker aroma than dairy-based yogurt, it is more potent than walnut purple rice milk. Additionally, its relative abundance of olefins, ketones, and alcohols enhances its unique flavour profile, surpassing both other options. Based on sensory analysis, it can be deduced that walnut purple rice yogurt has the highest overall acceptance rate.

Electrodeposition of cadmium telluride (CdTe) on fluorine doped tin oxide (FTO) using two electrode configuration was successfully achieved with the main focus on the growth temperature. The electroplating temperatures explored ranges between (55 and 85)℃ for aqueous electrolytes containing 1.5 M cadmium nitrate tetrahydrate (Cd(NO3)2 •4H2O) and 0.002 M tellurium oxide (TeO2). The ensuing CdTe thin-films were characterised using X-ray diffraction (XRD), UV-Vis spectrophotometry, scanning electron microscopy (SEM), energy dispersive X-ray (EDX) and photoelectrochemical (PEC) cell measurements. The electroplated CdTe thin-films exhibit a dominant (111) CdTe cubic structure, while the crystallite size increases with the increase in the electroplating temperature. The internal strain, dislocation density and the number of crystallites per unit area decrease with increasing growth temperature. The optical characterization depicts that the CdTe samples show comparable absorbance and a resulting bandgap of 1.51±0.03 eV for as-deposited CdTe layers. A marginal increase in the bandgap and reduction in the absorption edge slope towards lower deposition temperatures were also revealed. The annealed CdTe thin-films showed improvement in energy bandgap as it tends towards 1.45 eV while retaining the aforementioned absorption edge slope trend. Scanning electron microscopy shows that the underlying FTO layers are well covered with increasing grain size observable relative to the increase in the deposition temperature. The energy dispersive X-ray analyses show an alteration in the Te/Cd relative to the deposition temperature. Higher Te ratio with respect to Cd was revealed at deposition temperature lower than 85℃. The photoelectrochemical cell study shows that both p- and n-type CdTe can be electroplated and that deposition temperatures below 85℃ at 1400 mV results in p-type CdTe layers.

The Reactive Spark Plasma Sintering (R-SPS) method is compared in this work with the two-steps SHS-SPS route, based on combination of the Self-propagating High-temperature Synthesis (SHS) with the SPS process, for the fabrication of dense (Hf0.2Mo0.2Ti0.2Ta0.2Nb0.2)B2-SiC and (Hf0.2Mo0.2Ti0.2Ta0.2Zr0.2)B2-SiC ceramics. A multiphasic and inhomogeneous product, containing various borides, is obtained at 2000°C/20min by R-SPS, from transition metals, B4C and Si. In contrast, if the same precursors are first reacted by SHS, and then processed by SPS under the optimized condition of 1800°C/20min, the desired ceramics are successfully attained. Both High-Entropy-Boride/SiC products display densities > 97%, uniform microstructures and contained only small amounts of residual oxides (<2.4 wt.%). The presence of SiC makes the sintering temperature milder, i.e. 150°C below to that needed by the corresponding additive-free system. Fracture toughness is also markedly improved, particularly when considering the Nb-containing system processed at 1800°C/20min, whereas KIC progressively decreases (from 7.35 to 5.36 MPa m1/2) as the SPS conditions become more severe. SiC addition is found to inhibit the volatilization of metal oxides like MoO3 formed during oxidation experiments, thus avoiding mass loss in the ceramics. The benefits above also likely take advantage of the fact that the two composite constituents are synthesized in parallel, according to the SHS-SPS approach, rather than being produced separately and combined subsequently, so that strong interfaces between them are formed.

Abiotic stress in plants is an increasingly common problem in agriculture, and thus, studies on plant treatments with specific certain compounds that may help to mitigate these effects have increased in recent years Melatonin (MET) application and its role in mitigating the negative effects of abiotic stress in plants have become important in the last few years. MET, a derivative of tryptophan, is an important plant-related response molecule involved in the growth, development, and reproduction of plants, and the induction of different stress factors. In addition, MET plays a protective role against different abiotic stresses such as salinity, high/low temperature, high light, waterlogging, nutrient deficiency and stress combination by regulating both the enzymatic and non-enzymatic antioxidant defense systems. Also, MET interacts with many signaling molecules, among these, reactive oxygen species (ROS) and nitric oxide (NO), and participates in a wide variety of physiological reactions. It is well known that NO produces S-nitrosylation and NO2-Tyr of important antioxidant-related proteins, being this an important mechanism for maintaining the antioxidant capacity of the AsA/GSH cycle under nitro-oxidative conditions, being extensively reviewed here under different abiotic stress conditions. Lastly, in this review, we show the coordination between NO and MET as a long-range signaling molecule, regulating many responses in plants, including plant growth and abiotic stress tolerance. Despite all the knowledge acquired over the years, there is still more to know about how MET and NO act on tolerance to abiotic stresses.

A novel method of investigating the temperature dependent variation of aspects of the complex refractive index n* in samples in the THz range using continuous, non-polarised, synchrotron radiation is presented. The method relies on the use of ATR apparatus, and retains the advantage of minimal sample preparation, which is a feature of ATR techniques. The method demonstrates the viability of rapidly monitoring temperature reflectance whilst continuously heating or cooling samples by using a temperature variable Thermal Sample Stage. The method remains useful when the refractive index of the sample precludes attenuated total reflection study. This is demonstrated with the water reflectance experiments. The temperature dependent ATR reflectance of tissue-representative fats (lard and Lurpak® butter) was investigated with the novel approach. Both are within the ATR range of the diamond crystal in a “true” ATR mode. Lard showed no clear temperature variation between -15 0C and 24 0C at 0.7 to 1.15 THz or 1.70 to 2.25 THz. Lard can be regarded as having invariable, constant, dielectric properties within mixtures when biological substances are being assessed for temperature dependent dielectric variation within the stated THz ranges. Lurpak® butter (water content 14.7%) displayed temperature dependent reflectance features with a steady decline in reflectivity with increasing temperature. This is in line with the temperature-dependent behaviour of liquid water. There is no rapid change in reflectance, even at -20 0C, suggesting that emulsified water retains liquid-water-like THz properties at freezing temperatures.

This paper investigates the flexural behavior of unfired and fired one-way slabs constructed from reinforced ferronickel slag-based alkali-activated concrete. The study aims to expand the limited knowledge of large-scale testing of alkali-activated concrete structural elements, with a particular emphasis on their post-fire performance. Four slabs, each measuring 2.1 × 0.9 × 0.18 m³, were produced—two made of alkali-activated concrete and two of conventional concrete incorporating ordinary Portland cement. Both types of concrete exhibited similar compressive strengths. In each group, one slab served as a reference (control specimen—tested under monotonic four-point bending in its original state), while the other was subjected to a standard fire curve on the tensioned side before mechanical testing. The fired slabs were then tested in a cooled condition under ambient conditions. The effect of fire on the alkali-activated concrete was further examined using mercury intrusion porosity and scanning electron microscopy. The results reveal that the load capacity of structural members cast with alkali-activated concrete is only slightly lower than that of their conventional concrete counterparts (6% lower). However, the alkaliactivated slabs retain more of their stiffness and ductility after fire exposure.

BACKGROUND: Qu-aroma is a critical quality indicator for medium-high temperature Daqu (MT-Daqu), significantly influencing the aroma profile of strong-aroma Baijiu (SAB). SAB is produced across various regions in China, each with unique environmental conditions and production techniques. These regional differences are likely to cause variations in the Qu-aroma of MT-Daqu. Despite this, comprehensive research on the variations in Qu-aroma across different regions has been lacking. This study aims to address this gap by utilizing Gas Chromatography-Olfactometry-Mass Spectrometry (GC-O-MS) and electronic nose (E-nose) technology, combined with sensory evaluation, to analyze the differences in Qu-aroma characteristics and volatile compound profiles of MT-Daqu from seven distinct production areas.RESULTS: Sensory analysis identified seven broad aroma categories and 25 specific aromas characterizing the Qu-aroma of MT-Daqu samples. Chen aroma and roasted aroma were notably more prevalent in MT-Daqu samples from Sichuan compared to those from other regions (P < 0.05), while the fermentation aroma was less prominent in Sichuan samples. In total, 123 volatile compounds were detected in MT-Daqu, with 46 classified as aroma-active compounds. Among these, 21 aroma-active compounds were identified as markers distinguishing Sichuan MT-Daqu from those produced in non-Sichuan regions, showing significant differences in their concentrations (P < 0.05). Additionally, six major aroma-active compounds-ethyl isovalerate, ethyl heptanoate, hexanal, 1-nonanal, (E)-2,4-decadienal, and 2,3-dimethyl-5-ethylpyrazine-were found to significantly contribute to the aroma differences between Sichuan and non-Sichuan MT-Daqu.CONCLUSION: This study delineates the distinct Qu-aroma characteristics of MT-Daqu from various SAB production areas and identifies the aroma-active compounds responsible for these differences. The insights gained from this research offer valuable guidance for optimizing flavor profiles in MT-Daqu production, potentially enhancing the overall quality and regional distinctiveness of the product.

The major challenge in the current context of a rising world’s energy demand is to limit the global temperature increase for mitigating climate change. This goal requires a large reduction of CO2 emissions, mainly produced by power generation and industrial processes using fossil fuels. In this study, a novel methodology for K2CO3-doped Li4SiO4 sorbents production for CO2 capture at high temperature was adopted based on the Design of Experiments (DoE). Different synthesis (temperature and K2CO3 content) and adsorption conditions (sorption temperature and CO2 concentration) were systematically tested by Response Surface Methodology (RSM) to obtain predictive models of CO2 uptake and Li4SiO4 conversion. The results of RSM analysis evidenced a maximum adsorption capacity of 196.4 mg/g for a sorbent produced at 600 °C and with 36.9 wt% of K2CO3, tested at 500 °C and 4 vol% of CO2. Whereas at 50 vol% of CO2, the best uptake of 295.6 mg/g was obtained with a sorbent synthesized at 600 °C, containing less K2CO3 (17.1 wt%) and tested at higher temperature (662 °C). The obtained results highlight that K2CO3-doped Li4SiO4 sorbents can be tailored for maximizing CO2 capture at different operating conditions, making them suitable for use in industrial processes.

Carbonization of a biopolymer (lignin) in self-propagating high-temperature synthesis (SHS) led to the production of 2D graphene structures. With the help of modern analytical methods (Raman spectroscopy, X-ray diffraction) and electron microscopy, the resulting product was confirmed to have a few-layer 2D graphene structure. The predicted photovoltaic properties of the resulting few-layer graphene were implemented for laser ignition of a model pyrotechnic composition based on porous silicon. A phenomenological model of the formation mechanism of 2D graphene structures under the conditions of the SHS process is proposed.

Microemulsions with excellent properties have shown significant potential for enhancing oil recovery from tight formations through spontaneous imbibition. This work present a high-temperature-tolerant lower-phase microemulsion (HTLP-ME) using a microemulsion dilution method. The properties and morphological characteristics of HTLP-ME were evaluated and proposed a enhanced spontaneous imbibition oil recovery mechanism using imbibition tests and CT scanning technology. The results show that the optimum concentration of HTLP-ME is 0.2wt% has a superior thermal stability, small particle size, lower IFT, good wettability alteration ability, and minimum adsorption loss. Imbibition and CT experiments showed that the longer the imbibition distance, the better is the effect on spontaneous imbibition oil recovery. Furthermore, the solubilization coefficient and self-driving force were defined and calculated to quantitatively analyze the imbibition mechanisms. The imbibition mechanisms demonstrate that the reduction of oil/solid adhesion is due to the synergistic effect of IFT reduction and wettability alteration, and the ability to increase the imbibition distance through a larger self-driving force.

At present, in the field of aviation industry, titanium alloy is mainly used to manufacture parts such as compressor disc, blade and casing of aircraft engine. When working, titanium alloy parts produce high temperature due to high-speed running friction, which makes the high temperature oxidation resistance and friction resistance of titanium alloy greatly reduced. When their working environment contains salt, titanium alloys are subjected to thermal corrosion, which limits their wider practical applications. This paper introduce the aluminide coating and its preparation methods. The characteristics and functional mechanism of three functional coatings for service environment, such as high temperature resistant alumina-based coating, thermal corrosion resistant alumina-based coating and wear-resistant alumina-based coating are summarized. Finally, the development direction of composite coatings of titanium and titanium alloys for complex service environment is prospected.

Canola is the major oilseed crop of Canada. The de-oiled material is an important by-product due to its rich phenolic profile and high protein content. This co-processing stream from canola is primarily utilized as animal feed but represents an invaluable source of nutraceuticals. Microwave-assisted solvent extraction (MAE), as a green extraction method, has received considerable attention in recent times. The ease of use and application of many solvents at the same time makes the MAE one of the best methods for studying multiple solvents at the same time. The formation of canolol, from sinapine and sinapic acid, is primarily dependant on temperature which favors the decarboxylation reaction. Hence, MAE using green extractants can be used to enhance the yield of canolol. This study examined the effects of different pre-treatment temperature-time combinations of 140, 150, 160, and 170℃ for 5, 10, 15, 20 and 30 minutes on the extraction of canolol and other canola endogenous phenolic compounds. Three antioxidant assays assessed the antioxidant activity of the different extracts obtained by MAE confirming the microwave as a novel and versatile instrument for enhancing the yield of canolol. Improvements in the antioxidant activity of the different extracts further established the efficacy of the current method for isolating important natural phenolic derivatives for utilization by the nutraceutical industry.

Drought and high temperature often occur simultaneously will eventually affect rice (Oryza sativa L.) yield and seed quality. The objective of the study was to compare the effects of high temperature (HT) and water limitation (WL) during seed development and maturation on yield component, seed quality, and amylose content in aerobic rice cv. MRIA. Two experiments were conducted concurrently in greenhouse with ⁓35/26℃ subjected to elevated HT and/or WL; 5 days 38/28°C at 10, 15, 29 DAA and/or HT; 7 days at 40/28℃ at 8 and 21 DAA with 12h photoperiod in control environment growth chamber. Both experiments were respectively harvested at physiological maturity of 31 and 35 DAA. Grain yielded from the irrigated plant declined from over 27% to below 18% between 15 and 29 DAA. Combination stresses resulted in greater reduction of grain yield than single stress. Late seed development (29 DAA) had no effect either on yield component or seed quality as well as produce a high concentration in amylase content (16.7%) with greater germination capacity (91%). The non-stress plant harvested at 21 DAA resulted the highest percentage of germinated seeds (97%) whereas the vigour index (VI) was reduced to 70.3% and 58.9% at 8 and 21 DAA respectively. Extended plant stress to 7 consecutive days incurred the highest VI with low concentration of amylose content. There was a linear relationship incurred between seed amylase content with germination capacity and VI, however, there was an inverse relationship (R2 = 0.19) between amylase content with VI from plant treated with (HT and/or WL) for 7 days. The present results confirmed that the avoidance HT and WL during early (10 DAA) and mid (15 DAA) seed development with short duration of stress (5 days) obtained better in yield component, enhanced the seed quality and amylose concentration. The combined HT and WL damaged seeds’ quality were more than each stress alone. Therefore, avoiding HT and WL can be practically applied by farmers by irrigating throughout the rice plant during histodifferentiation to save water usage during seed maturation.

Rice production, owing to its high-water requirement for cultivation, is very vulnerable to the threat of changing climate, particularly prolonged drought and high temperature. Such threats heighten the need for abiotic stress-resilient rice varieties with better yield potential. This review examines the physiological and molecular mechanisms of rice varieties to cope with stress conditions of drought (DS), high temperature (HTS) and their combination (DS-HTS). It appraises research studies in rice about its various phenotypic traits, genetic loci and response mechanisms to stress conditions to help craft new breeding strategies for rice varieties with improved resilience to abiotic stresses. This review consolidates available information on promising rice cultivars with desirable traits as well as advocates synergistic and complementary approaches in molecular and systems biology to develop new rice breeds that favorably respond to climate-induced abiotic stresses. The development of new breeding and cultivation strategies for climate-resilient rice varieties is a challenging task. It requires a comprehensive understanding of the various morphological, biochemical, physiological, and molecular components governing yield under drought and high temperature, but possible by implementing cohesive approaches involving molecular and systems biology approaches in genomics and molecular breeding, including genetic engineering.

Soil tillage intensity influences the distribution of nutrients, and soil’s physical and me-chanical properties, as well as gas flows. The impact of reduced tillage on these indices in spring barley cultivation is still insufficient and requires more analysis on a global scale. This study was carried out at Vytautas Magnus University, Agriculture Academy (Lithu-ania) in 2022–2023. The aim of the investigation was to determine the effect of the tillage systems on the soil temperature, moisture content, CO2 respiration and concentration in spring barley cultivation limited by the semi-humid subarctic climate. Based on a long-term tillage experiment, five tillage systems were tested: deep and shallow mold-board ploughing, deep cultivation-chiselling, shallow cultivation-chiselling, and no-tillage. Shallow ploughing technology was found to be better at conserving soil moisture and maintaining a higher temperature. Deep cultivation had a lower moisture content and lower soil temperature. Shallow cultivation fields in most cases increased CO2 emissions and CO2 concentration. The results show that in direct sowing fields, most cases had a positive effect on crop density. Direct sowing fields resulted in significantly lower grain yields of spring barley in the years studied.

Temperature field is an essential attribute of metal additive manufacturing in view of its bearings on the prediction, control, and optimization of residual stress, part distortion, fatigue, balling effect, etc. This work provides an analytical physics-based approach to investigate the effect of scan strategy parameters including time delay between two irradiations and hatching space on thermal material properties and melt pool geometry. This approach is performed through the analysis of the distribution of material properties and temperature profile in three-dimensional space. The moving point heat source approach is used to predict the temperature field. To predict the temperature field during the additive manufacturing process some important phenomena are considered. 1) Due to the high magnitude of temperature in the presence of the laser, the temperature gradient is usually high which has a crucial influence on thermal material properties. Consequently, the thermal material properties of stainless steel grade 316L are considered to be temperature-dependent. 2) Due to the repeated heating and cooling, part usually undergoes several melting and solidification cycles. This physical phenomenon is considered by modifying the heat capacity using the latent heat of melting. 3) The multi-layer aspect of metal AM process is considered by incorporating the temperature history from the previous layer since the interaction of the successive layers has an impact on heat transfer mechanisms. 4) Effect of heat affected zone on thermal material properties is considered by the superposition of material properties in regions where the temperature fields of two consecutive irradiations have an overlap since the consecutive irradiations change the behavior of the material properties. The goals are to 1) investigate the effects of temperature-sensitive material properties and constant material properties on the temperature field. 2) Study the behavior of thermal material properties under different scan strategies. 3) Study the importance of considering the effect of heat affected zone on thermal material through the prediction of melt pool geometry. 4) Investigate the effect of hatching space on melt pool geometry. This work is purely employed physics-based analytical models to predict the behavior of material properties and temperature field under different process conditions, and no finite element modeling is used.

In order to further control the equivalent circulating density,a new type of annular pres-sure-reducing downhole tool for high temperature and high pressure wells-liquid-absorbing ECD tool is designed.Through this tool,the bottom hole pressure of the equivalent circulating drilling fluid can be close to its hydrostatic pres-sure,therebyachieving a deeper drilling depth.The tool is mainly composed of screw mo-tor,vortex blade,annular seal,universal joint and drill string.Its working principle is mainly to use the liquid absorption effect of the tool and the hydraulic energy of the circu-lating fluid extracted by the screw motor to convert it into mechanical energy,and to gen-erate suction force to improve the flow energy of the drilling fluid in the bottom hole an-nulusand reduce the equivalent circulation density.Based on ANSYS-FLUENT analysis andsimulation,the change of pressure drop characteristics under different drilling fluid density,displacement and tool size was simulated.The simulation results show that thedepressurization effect is 1.0MPa when the drilling fluid density is 1.2g/cm3. When the drilling fluid density is 1.5g/cm3,the depressurization is about 1.7MPa,and when thedrill-ing fluid density is 1.8g/cm3,the depressurization is about 1.9MPa.When the drilling fluid density is 2.0g/cm3,the pressure drop is about 2.3MPa.When the flow rate is from 1500-2500L/min,the maximum pressure can be reduced by 2.3MPa.When the viscosity is 40mPa•S and 60mPa•S,the pressure drop almost does not change.The increase of viscosi-ty has little effect on the pressure drop,and it is mainly affected by the flow rate under equal displacement.

Laser powder bed fusion (LPBF) is an additive manufacturing process employed in many industries, for example for aerospace, automotive and medical applications. In these sectors, mainly nickel-, aluminum- and titanium-based alloys are used. In contrast, the mechanical engineering industry is interested in more wear-resistant steel alloys with higher hardness, both of which can be achieved with a higher carbon content, like in high-speed steels. Since these steels are susceptible to cracking, preheating needs to be applied during processing by LPBF. In a previous study, we applied a base plate preheating temperature of 500 °C for HS6-5-3-8 with 1.3 % carbon content. We were able to manufacture dense (p > 99.9 %) and crack-free parts from HS6-5-3-8 with a hardness > 62 HRC (as built) by LPBF. In this study, we investigate the influence of preheating temperatures up to 600 °C on hardness and microstructure dependent on part height for HS6-5-3-8. The microstructure was studied by light optical microscopy (LOM), scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD). The analysis of hardness and microstructure at different part heights is necessary because state-of-the-art preheating systems induce heat only into the base plate. Consequently, parts are subjected to temperature gradients and different heat treatment effects depending on part height during the LPBF process.

TiC–high Mn steel-bonded carbide with a cellular structure was designed and fabricated by powder metallurgy techniques using coarse and fine TiC particles as the hard phase. This preparation process was carefully investigated and optimized. The microstructure of the TiC steel-bonded carbide was observed using a scanning electron microscope. Results showed that there are two types of microstructures in the TiC steel-bonded carbide: the coarse-grained TiC and fine-grained TiC. The transverse rupture strength and impact toughness of the alloy reach maximum values 2231 MPa and 12.87 J/cm2, respectively when the starting weight ratio of MP-A (containing coarse TiC particles) to MP-B (containing fine TiC particles) is 60:40. Hence, this study serves as a feasible example of how to prepare a high-strength and high-toughness TiC–high Mn steel-bonded carbide.

The lipid composition of biomembranes influence the properties of the lipid bilayer as well as that of the proteins. In this study, the lipidome and the lipid/protein ratio of membranes from High FiveTM insect cells overexpressing mouse P-glycoprotein was characterized. This provides a better understanding of the lipid environment in which P-glycoprotein is embedded, and thus of its functional and structural properties. The relative abundance of the distinct phospholipid classes and their acyl chain composition was characterized. A mass ratio of 0.57 +/- 0.11 phospholipids to protein was obtained. Phosphatidylethanolamines are the most abundant phospholipids, followed by phosphatidylcholines. Membranes are also enriched in negatively charged lipids (phosphatidylserines, phosphatidylinositols and phosphatidylglycerols), and contain small amounts of sphingomyelins, ceramides and monoglycosilatedceramides. The most abundant acyl chains are monounsaturated, with significant amounts of saturated chains. The characterization of the phospholipids by HPLC-MS allowed identification of the combination of acyl chains, with palmitoyl-oleoyl being the most representative for all major phospholipid classes except for phosphatidylserines, which are mostly saturated. A mixture of POPE:POPC:POPS in the ratio 45:35:20 is proposed for the preparation of simple representative model membranes. The adequacy of the model membranes was further evaluated by characterizing their surface potential and fluidity.

An innovative superconducting mechanism was developed based on a patented discovery of room temperature superconductivity in several thorium (Th) salts or compounds. The rationale behind this discovery is through the experimental results about the unique electrical and magnetic properties of these Th salts. Accordingly, this new superconducting mechanism for these Th salts was obtained through the analyses of the compounds’ molecular configurations and the packings of their relevant crystal structures. Owing to the distinctive properties of the Th compounds in this discovery, we further established a different electron pairing scheme as opposed to the pairing of the Cooper pairs. Compared to the long distance electron pairing of the Cooper pairs, the new electron pairing in our mechanism is constructed by two closely correlated electrons that reside on the same atomic orbital of the Th cation as an electron lone pair. In this new superconducting mechanism, the Th cation is sitting on a relevant crystallographic lattice arrangement or a network of the relevant Th compounds. This network is constructed by many Th cations along certain crystallographic lattice arrangement where each Th cation contains one electron lone pair. This network allows the electron lone pairs on the Th cations to be delocalized over the network, “in pair”, and thus, reveals the electron lone pair in presence in a long distance fashion. The closely correlated electron lone pairs hop on this network and thus, construct the supercurrent over the network. This explanation about the superconductivity laid the basis for our superconducting mechanism. All these conclusions came from the previous studies about these compounds that illustrated their unusual features of a coexistence of high electrical conductivity and diamagnetism. These electrical and magnetic properties fall in line with that of superconductors but, surprisingly, these Th compounds have such properties at the ambient condition, meaning under room temperature and atmosphere pressure. We expect that this mechanism may be appropriate to be utilized to other superconducting cases, either conventional or unconventional, and therefore, can be adapted to describe the superconducting phenomenon for other superconductors.

This research investigates the fatigue crack propagation on the lower surface of rocket deflector troughs of offshore rocket launch platforms. Initially, a numerical model of the offshore rocket launch platform is established using ABAQUS based on the Extended Finite Element Method (XFEM). Subsequently, two variable parameters—namely, the initial crack length and initial tilt angle—are introduced. This research systematically analyzes the impact of these parameters on fatigue crack propagation patterns in both the maximum stress and maximum deformation regions of the deflector channels under the combined conditions of high temperature and impact. Finally, the research indicates that the propagation length of surface cracks in the deflector trough exhibits a trend of initial increase followed by a subsequent decrease with the increase in the preset inclination angle. Notably, the stable propagation rate of the crack in the region of maximum deformation surpasses that observed in the region of maximum stress. Through meticulous comparative analysis, it is evident that temperature loading significantly fosters the initiation and propagation of cracks, particularly in the upper region of the deflector channel's lower surface.

This study investigates the effect of Re addition on the microstructure evolution and oxidation resistance of Co-Cr-Ta-Ti-C alloys. The alloys tested in this study consist of a Co-rich matrix with mixed HCP and FCC phases, together with TaTiC2 and Ti-based carbides. The addition of Re promotes the precipitation and growth of a CoCr-rich σ phase. Differential thermal analysis (DTA) showed that the melting temperatures did not change drastically up to 10 at% Re addition, whereas 15 at% Re addition significantly increased the melting temperature of the alloys. Oxidation tests in air at 1200°C showed that excessive Re content could lead to deterioration in oxidation resistance, mainly due to the accelerated formation of volatile Re oxides.

Oscillations in global modes of variability (MoV) form global teleconnections that affect regional climate variability and modify the potential for severe and damaging weather conditions. Understanding the link between certain MoVs and regional climate can improve the ability to more accurately predict environmental conditions that impact human life and health. In this study, we explore the connection between different MoVs, including the Arctic Oscillation (AO), Eurasian teleconnection, Indian Ocean Dipole (IOD), North Atlantic Oscillation (NAO), and El Niño Southern Oscillation (Nino34), with winter and summer climate in the High Mountain Asia (HMA) region, including geopotential height at 250 hPa (z250), 2-m air temperature (T2M), total precipitation (PRECTOT), and fractional snow cover area (fSCA). Relationships are explored for the same monthly period between the MoVs and the climate variables, but also using a lagged correlation analysis to investigate whether any relationship exists at different time lags. We find that T2M has a negative correlation with the Eurasian teleconnection in the Inner Tibetan Plateau and Central China in both winter and summer and a positive correlation in Western China in summer. PRECTOT has a positive correlation with all MoV in most regions in winter, especially with the IOD, and a negative correlation in summer, especially with the Eurasian teleconnection. Snow cover in winter is positively correlated with most indices throughout many regions in HMA, likely due to wintertime precipitation also being positively correlated with most indices. Generally, the AO and NAO show similar correlation patterns with all climate variables, especially in the winter, possibly due to their oscillations being so similar. Furthermore, the AO and NAO are shown to be less significant in explaining the variation in HMA climate compared to other MoVs such as the Eurasian teleconnection. Overall, our results pinpoint different time-windows and specific regions within HMA that exhibit high correlation between climate and MoVs, which might offer additional predictability of the MoVs as well as of climate and weather patterns in HMA and throughout the globe.

The mechanical behavior, microstructures as well as the crystallographic textures of the Ti57-Nb43 alloy were investigated on cylindrical specimens compressed at high temperatures, in the range of 700-1000 °C, and strain rates between 0.001 and 1.0 s-1. Hardening, followed by softening behaviours were observed as a function of strain, due to the occurrence of dynamic recrystallization/recovery in hot deformation. The modified five-parameter Voce type equation described well the stress-strain curves, but for the present alloy, it was also possible with only four parameters. A new two-variables polynomial function was employed on the four parameters that described well the flow curves as a direct function of temperature and strain rate. It permitted to reduce the number of parameters and had the predictive capacity for the flow stress at any temperature, strain, and strain rate in the investigated range. The crystallographic textures were similar at all temperatures with an increase of intensity from 900 °C. The textures could be characterized by a double &lt;100&gt; and &lt;111&gt; fiber and a unique component of (001)&lt;110&gt;, the latter inherited from the initial hot rolling texture. Viscoplastic polycrystal self-consistent deformation modeling reproduced the measured textures showing that dynamic recrystallization did not alter the development of the deformation texture, only increased it intensity.

Bitumen is produced from non-renewable natural resources, continuously deplete and intrigues researchers to look for alternative binders. Annually, tons of waste engine oil (WEO) and crumb rubber (CR) are discarded unsustainably and pose a significant environmental threat. Adding these industrial waste products to asphalt provides a safe and cost-effective way for their disposal and improves the bitumen's performance in parallel. This study uses various combinations of waste engine oil and crumb rubber with 60/70 penetration grade bitumen to produce a partially synthetic bitumen. Adhesion being one of the critical characteristics of the bituminous binder has been assessed using the bitumen bond strength test along with physical and rheological properties. Results showed that waste engine oil with crumb rubber inclusion increases penetration and decreases the softening point, viscosity, complex modulus, and bonding strength. Additionally, polyphosphoric acid (PPA) in smaller dosages was also incorporated into the optimum percentage of CR + WEO to improve the properties of the binder. The results confirm that binder modification with waste engine oil and crumb rubber can be more effective with PPA. It is concluded that 35% of waste can replace the virgin binder giving a cost-effective and environmentally friendly solution.

Using analysis methods such as Rutherford backscattering Spectrometry, scanning electron microscopy, X-ray diffraction, and Raman spectroscopy, the diffusion behavior of iodine in micro/nano-porous graphite under high-temperature conditions was studied. The results indicate that iodine diffusion leads to the contraction of graphite microcrystals, a decrease in interlayer spacing, and an increase in defect density, resulting in a reduction in microcrystal size. Upon diffusion of iodine out of iodine-loaded graphite, the microcrystal size of the graphite increases, the interlayer spacing appears to return to the initial state, and the defect density decreases. By comparing the iodine diffusion performance of nanoporous graphite G400 and G450 with microporous graphite G500, it was determined that nanoporous graphite exhibits better inhibition of iodine diffusion compared to microporous graphite. Studying the diffusion behavior of iodine in micro/nano-porous graphite has significant academic significance and engineering value for the screening, design, and performance optimization of nuclear graphite.

High temperature titanium alloys are widely used in aerospace hot parts, however, the thermal barrier temperature of 600 oC limits its service temperature. In this paper, a two-step hot-dip plating method is proposed to prepare the composite coating containing Ce on the surface of titanium alloy, which can make the oxidation resistance temperature of titanium alloy reach 800 oC The microstructure, phase composition and element distribution of Ce-containing Ti-Al-Si hot-dip coating, Ce-containing Ti-Al-Si pre-oxidation coating and Ce-containing Ti-Al-Si high-temperature oxidation coating were studied by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS), respectively. The results show that the Ti-Al-Si hot-dip coating containing Ce is mainly composed of (Ti,Ce)(Al,Si)3 alloy phase layer, and the Ti-Al-Si pre-oxidation coating containing Ce is mainly composed of Ti-Al binary system phase layer and dense Al2O3 layer rich in CeO2. Ce in the high temperature oxidation coating of Ti-Al-Si containing Ce is mainly distributed in Ti3Al, TiAl, TiAl3+Ti5Si3 mixed phase layer and Al2O3. The addition of Ce can promote the formation of continuous Al2O3 layer, improve the uniformity of composite coating, prevent the spread of cracks, and improve the high temperature oxidation resistance of Ti-Al-Si coating.

In this paper, through high-temperature tensile tests of 55NiCrMoV7 steel, the high-temperature fracture behavior, microstructure evolution and carbide distribution characteristics of both thermal-mechanical coupling zone (fracture zone) and thermal stress zone (clamping zone) at different temperatures were studied. Intrinsic relationship between high temperature fracture and carbides types, distribution and size were revealed and evolution mechanism of microstructure near cracks in 55NiCrMoV7 hot-working die steel during high temperature deformation was clarified. Samples were stretched at different temperatures from 25 °C to 700 °C, and microscopic examinations were carried out by using SEM and TEM. The results showed that: With the increase of temperature, tensile strength and yield strength decreased, elongation and reduction of area increased, and fracture mode changed from brittle fracture to ductile fracture by transition temperature at about 400℃. During high temperature deformation, the grain dislocation density decreased, the tempered martensite decomposed, recovered, recrystallized, and then grain grew. M7C3 and M23C6 carbides precipitated and grew along the grain boundary, and a small amount of fine granular MC carbides were dispersed in the grain. The work done by the external force on the deformation zone would cause the temperature of it to be higher than tensile temperature, which provides thermodynamic conditions for the re-dissolution of small carbides near the fracture zone and the grain growth of large carbides, resulting in the decrease of small carbides and increase of large carbides in thermal-mechanical coupling zone.

Hyper duplex stainless steels, HDSS, are a new alloy group of duplex stainless steels with the highest corrosion resistance and mechanical properties among the existing modern stainless steel. Due to the addition of extra high content of alloying elements, e.g. Cr, Ni, Mo, etc., the crystallization behavior of the δ-ferrite from the liquid is of vital importance for controlling the steel properties. In this work, the effect of cooling rate (i.e. 4°C/min and 150 °C/min) on the growth process of δ-ferrite in S33207 during the solidification process was investigated using high-temperature confocal scanning laser microscopy (HT-CLSM) in combination with electron microscopes and thermodynamic calculation. The results showed that the solidification mode of S33207 steel was a ferrite-austenite type (FA mode). L→δ transformation occurred at a certain degree of supercooling, and merging occurred during the growth of δ phase dendrites. Similar microstructures were observed after solidification under these two different cooling rates. The variation of area fraction of δ ferrite at the free surface and temperature as well as time during solidification of S33207 steels were calculated at different cooling rates of 4 °C/min and 150 °C/min, respectively. The current HT-CLSM study provides in-situ experimental evidence to confirm that a low cooling rate favored the growth of primary δ-ferrite, whereas a high cooling rate favored the nucleation of primary δ-ferrite during the solidification process. The post-microstructure as well as composition evolution is also briefly investigated. This work shed light on the real time insights for the crystallization behavior of hyper duplex stainless steels during solidification, which aims to contribute to the process control of manufacturing of this steel grade.

We propose a chemical language processing model to predict polymers’ glass transition temperature (Tg) through a polymer language (SMILES, Simplified Molecular Input Line Entry System) embedding and recurrent neural network. This model only receives the SMILES strings of polymer’s repeat units as inputs and considers the SMILES strings as sequential data at the character level. Using this method, there is no need to calculate any additional molecular descriptors or fingerprints of polymers, and thereby, being very computationally efficient and simple. More importantly, it avoids the difficulties to generate molecular descriptors for repeat units containing polymerization point `*’. Results show that the trained model demonstrates reasonable prediction accuracy on unseen polymer’s Tg. Besides, this model is further applied for high-throughput screening on an unlabeled polymer database to identify high-temperature polymers that are desired for applications in extreme environments. Our work demonstrates that the SMILES strings of polymer’s repeat units can be used as an effective feature representation to develop a chemical language processing model for predictions of Tg. The framework of this model is general and can be used to construct structure-property relationships for other polymer’s properties.

The work focused on the development of high-temperature electrical insulation coatings for film photovoltaics. The idea was into replacing the electroconductive metal dispersed phase in siloxane high-temperature coating to ceramic particles with phonon thermal conductivity. The slurry of industrial composition based on polysiloxane lacquer and thermally conductive paste containing zinc oxide was centrifuged to obtain a thin, optically transparent coating with the destruction temperature of over 600 °C. Topology, electrical properties, and thermal conductivity of the resulting film were investigated. The mathematical model of thermal processes in films in the course of heating was figured out. Quantitatively the relation of thermal conductivities of a control sample and a sample with a heat-conducting filler was established. The effectiveness of using this technology is shown.

This paper reviews state of the art Additive Manufactured (AM) IN718 alloy intended for high temperature applications. AM processes have been around for decades and have gained traction in the past five years due to the huge economic benefit it brings to manufacturers. It is crucial for the scientific community to look into AM IN718 applicability in order to see a step-change in the production. Microstructural studies reveal that the grain structure plays a significant role in determining the fatigue lifespan of the material. Controlling IN718 respective phases such as the ϒ’', δ and Laves phase is seen to be crucial. Literature reviews have shown that the mechanical properties of AM IN718 were very close to its wrought counterpart when treated appropriately. Higher homogenization temperature and longer ageing were recommended to dissolve the damaging phases. Various surface enhancement techniques were examined to find out their compatibility to AM IN718 alloy that is intended for high temperature application. Laser shock peening (LSP) technology stands out due to the ability to impart low cold work which helps in containing the beneficial compressive residual stress it brings in high temperature fatigue environment.

Real-time evolution of the electron densities under excitations in La₂CuO₄ was calculated by the time-dependent density functional theory (TDDFT). The author found, for the first time, under excitations, the electron cloud of Cu²⁺ changes obviously and the characteristic frequencies are 83 meV and 36 meV, respectively, for two different modes. The results are unexpected and close to that of lattice vibrations. The results show that the electron cloud of Cu²⁺ (just like the lattice) can be the electron-pairing medium in high temperature copper oxide superconductors.

Continuous ultrasonic in-situ monitoring for industrial applications is difficult owing to the high operating temperatures in industrial fields. It is expected that ultrasonic transducers consisting of CaBi4Ti4O15(CBT)/Pb(Zr,Ti)O3(PZT) sol-gel composite could be one solution for ultrasonic nondestructive testing (NDT) above 500 C because no couplant is required and CBT has a high Curie temperature. To verify the high temperature durability, CBT/PZT sol-gel composite films were fabricated on titanium substrates by spray coating, and the CBT/PZT samples were tested in a furnace at various temperatures. Reflected echoes with a high signal-to-noise ratio were observed up to 600 C. A thermal cycle test was conducted from room temperature to 600 C, and no significant deterioration was found after the second thermal cycle. To investigate the long-term high-temperature durability, a CBT/PZT ultrasonic transducer was tested in the furnace at 600 °C for 36 h. Ultrasonic responses were recorded every 3 h, and the sensitivity and signal-to-noise ratio were stable throughout the experiment.

Magnetic iron oxide particles are used for in vitro diagnostics for nearly 40 years. Due to their unique physical, chemical, thermal and mechanical properties, as well as biocompatibility and low toxicity in the human body, iron oxide nanoparticles have been used in many biomedical applications, such as contrast agents for magnetic resonance imaging, carriers for controlled drug delivery and immunoassays, but also in magnetic hyperthermia. Our aim is to investigate the effect of pressure and temperature on the structural, thermal and magnetic properties of iron oxide nanomaterials prepared by hydrothermal synthesis. Iron oxide nanoparticles were synthesized at temperatures of 100-200°C and pressures of 20-1000 bar. It has been found that pressure influences the type of iron oxide crystalline phase. Thus, for lower pressure values (< 100 bar), iron oxide is predominantly formed as hematite, while at pressures > 100 bar, the major crystalline phase is goethite. The complex thermal analysis revealed the polymorphic changes of iron oxides at different temperatures. The existence of specific magnetite and hematite phases in all thermally treated samples are evidenced through the specific Verwey and Morin transitions highlighted by ZFC-FC (Zero Field Cooled-Field Cooled) measurements, whereas their relative content is precisely provided by Mössbauer spectroscopy.

Microcrystalline and near nanocrystalline AlCrFeCoNi high-entropy alloy (HEA) coatings were applied on Inconel 718 superalloy using air plasma spraying (APS) process. High-temperature oxidation behavior of the microcrystalline and near nanocrystalline AlCrFeCoNi HEA coated superalloy were examined at 110°C under the air atmosphere for 50 cycles under cyclic heating and cooling (1 h for each cycle). The oxidation kinetics of both nanocrystalline and microcrystalline coated superalloy was accordingly analyzed by weight change measurement. It was noticed that the uncoated and coated followed the parabolic rate law of the oxidation. X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), energy dispersive X-ray analysis (EDS), and elemental mapping techniques were used to analyze the oxidized coated and uncoated samples. In the HEA coated superalloy, Fe, Ni, Co, and Al were oxidized in the inter-splat region, whereas the splats which consist mainly of Ni and Cr remained unoxidized. Because of the formation of compact and adhesive thin NiO, CoO oxides, and spinels together with the Al2O3 oxide scale on the surface of the coating during oxidation, the developed nanocrystalline HEA coating shows better oxidation resistance than the microcrystalline HEA coating.

Economic development and population growth lead to increased production of chicken manure (CM), which is a problematic organic waste for its amount, environmental threats, and moisture content. There are different ways of CM, namely anaerobic digestion, composting, combustion, and direct land spreading. Hydrothermal carbonization (HTC) is another emerging way, however. In this study, the HTC of CM was performed to produce energy-rich material called hydrochar (HC). The effects of HTC temperature (180, 240, 300 C) and process time (30, 90, 180 min) were summarized. Proximate and ultimate analysis, as well as heating values (HHV, LHV), have been performed both on raw CM and derived HC. Additionally, the process performance has been examined. The obtained results show that HTC is a feasible method for CM disposal and valorization. Although process time did not influence considerably fuel properties of CM, higher temperature led to significantly higher HHV, reaching 23,880.6734.56 Jg-1 at 300 C and 180 min with an improvement of 8,329 Jg-1 compared with raw CM (15,551.67 Jg-1). The process conducted at 240 C in 30 min has been specified as the most favorable, due to the highest energy gain of HC and relatively low energy consumption.

A review is here provided on the thermal effects on the optical chirality. To this goal, chiral objects dispersed in an embedding fluid are examined for their magnetoelectric coupling. Archetypal twisted-Omega particles are examined with respect to electron transport, phonon dynamics, and temperature effects. Continuum-mechanical aspect of thermo-elasticity is reviewed along with transverse deformations. A transition temperature delineating a sign flip in the chirality parameter is identified as well.

Although Sugarcane bagasse ash (SCBA) has good cementitious property, previous researchers have primarily aimed to improve the mechanical performance of conventional concrete or cement-based composites. Research is lacking on ultra-high performance concrete (UHPC), especially regarding tensile self-sensing properties. This paper aimed to comprehensively evaluate the SCBA effect on the UHPC’s mechanical, electrical, and tensile self-sensing properties. The results showed that SCBA below the critical incorporation concentration (CIC) improved the UHPC’s mechanical properties compared to steel fibers alone. Furthermore, adding 3.0wt% SCBA remarkably enhanced the UHPC mechanical properties where the compressive, flexural, and tensile strengths increased by 13.1%, 17.4%, and 20.6%, respectively. The SCBA content of 0.3wt% achieved the maximum UHPC electrical resistivity since values smaller or greater than this content decreased the resistivity. The SCBA-enhanced UHPC showed better tensile stress-sensing performance than UHPC without SCBA due to improved linearity and reversibility, lower hysteresis, higher sensitivity, and superior repeatability. UHPC with 0.3wt% SCBA achieved the best linearity, while UHPC with 0.9wt% SCBA showed the highest sensitivity, lowest hysteresis, and best repeatability. Overall, the content of 0.9wt% SCBA is the best in improving the overall mechanical, electrical, and tensile self-sensing performance.

Intermetallic alloys like e.g. Iron-Aluminides, Titanium-Aluminides or Molybdenum- Silizides are prospective materials for high-temperature applications. For additive manufacturing (AM) intermetallic structural materials are particularly challenging due to their high melting points, oxygen susceptibility and low temperature brittleness. The feasibility of manufacturing intermetallic Mo-Si-B alloys with the laser additive manufacturing process of direct energy deposition (DED) is demonstrated and recent results in characterizing rapidly solidified material with respect to correlations between process, composition and microstructures are presented. The possibility to dope the material with Yttrium oxide (Y2O3) for dispersion is successfully demonstrated. Current challenges, e.g. homogenous distribution of alloying elements and applicability are addressed.

The objective of this paper was to verify the applicability of statistical learning (SL) compared to human reasoning with respect to the Universal Thermal Climate Index (UTCI), a complex tool for the assessment of outdoor thermal stress. UTCI is an equivalent temperature index based on the 48-dimensional output of an advanced model of human thermoregulation formed by 12 variables at four consecutive 30-minute intervals, which were calculated for 105642 thermal conditions from extreme cold to extreme heat. Comparing the performance of SL algorithms to the results accomplished by an international endeavor involving more than 40 experts from 23 countries, we found that random forests and k-nearest neighbors closely predicted UTCI values, but that clustering applied after dimension reduction algorithms (principal component analysis and t-distributed stochastic neighbor embedding) were inadequate for risk assessment in relation to the UTCI stress categories. This indicates a potential supportive role for SL, as it will not (yet) fully replace the bio-meteorological expert knowledge.

Different types of resonators are used to create acoustic metameterials and metasurfaces. Recent studies focused on the use of multiple resonators of dipole, quadrupole, octupole and even hexadecapole types. This paper considers the theory of an acoustic metasurface, which is a flat surface with a periodic arrangement of multiple resonators. The sound field reflected by the metasurface is determined. If the distance between the resonators is less than a half the wavelength of the incident plane wave, the far field can be described by a reflection coefficient that depends on the angle of incidence. This allows to characterize the acoustic properties of the metasurface by a homogenized boundary condition, which is a high order tangential impedance boundary condition. The tangential impedance depending on the multiple order of the resonators is introduced. In addition, we analyze sound absorption properties of these metasurfaces, which are a critical factor in determining their performance. The paper presents a theoretical model that accounts for the multiple orders of resonators and their impact on sound absorption. The maximum absorption coefficient for a diffuse sound field, as well as the optimal value for the homogenized impedance, are calculated for arbitrary multipole orders.

By using the method of high-temperature solid-phase reaction, the new piezoceramic SrBi2Nb2-2xWxSnxO9 was obtained, in which partial substitution of niobium (Nb) atoms with Sn4+ and W6+ atoms in the compound SrBi2Nb2O9 took place in the octahedra of the perovskite layer (B-position). X-ray diffraction studies have shown that these compounds are single-phase SrBi2Nb2-2xWxSnxO9 (x = 0.1, 0.2) and two-phase SrBi2Nb2-2xWxSnxO9 (x = 0.3, 0.4), but they all had the structure of Aurivillius – Smolensky phases (ASPs) with similar parameters of orthorhombic elementary cells, corresponding to the spatial group A21am. The dependences on temperature of the relative permittivity ε/ε0 and the tangent of the loss angle tan d at different frequencies were measured.

Catalyst with high catalytic activity and good stability are desirable in the electrocatalytic oxidation of glucose. Herein, Pt concave nanocubes with high-index facets (HIFs) supported by carbon black (Pt CNC/CB) are prepared through a hydrothermal method. The experimental results demonstrate that the peak current densities in different potential regions on the Pt CNC/CB anode are 0.22, 0.20, and 0.60 mA cm−2, respectively. The glucose oxidation reaction shows superior performances in basic and neutral conditions than in acid conditions. Better stability is achieved by Pt CNC/CB than Pt concave nanocubes (Pt CNCs). Abundant surface defects with low-coordinated atom numbers, such as the steps, kinks, and edges, are served as active sites in the electrocatalytic oxidation of glucose. With the addition of carbon black, the catalytic activity can be improved by facilitating the full exposure of the active surface defects on the HIFs of Pt CNCs. Moreover, to address the aggregation of Pt CNCs, caused by the high surface energy of HIFs, the introduction of carbon material is an effective way to preserve the HIFs, and thus enhance the stability of the catalyst. Hence, the prepared Pt CNC/CB electrocatalyst has great potential to be applied in the electrooxidation of glucose.

Recently Kawashima has reported that, when wetted with alkanes, several forms of graphite and single-layer graphene exhibit superconductor-like properties above room temperature under ambient pressure [AIP Adv. 2013, 3, 052132; arXiv:1612.05294; arXiv:1801.09376]. Under the assumption that these seemingly unlikely properties arise from the presence of paired electrons brought about by the alkane-wetting, we explored their implications to arrive at a probable mechanism for strong electron-pairing driven by Fermi surface nesting and acoustic phonon. This mechanism explains why alkane-wetting is essential for the graphene systems to become “superconductor-like” above room temperature and why the “T_c” of alkane-wetted pitch-based graphite fibers increases almost linearly from ~363 to ~504 K with increasing the molecular weight of alkane from heptane to hexadecane. It also provides a number of experimentally-verifiable predictions, the confirmation of which will provide a strong support for the superconductivity driven by Fermi surface nesting and acoustic phonon.

Abstract: : 2,3-dihydro-5,6,7,8-tetranitro-1,4-benzodioxine (TNBD), molecular formula =C8H4N4O10 is a completely nitrated in aromatic ring 1,4-benzodioxane derivative. The con-venient method of TNBD synthesis was developed (yield=81 %). The detailed structure of this compound has been investigated by X-ray crystallography. The results of differential thermal analysis (DTA) obtained with twice re-crystallized material showed onset at 247 and isoterm at 288 0C, with further total degradation at 300 0C. The experimental density 1,85 g/cm3 of TNBD was determined by X-ray crystallography. The spectral properties of TNBD (NMR, FT-IR, Ra-man) were explored. The detonation properties of TNBD calculated by EXPLO 5 code was slightly superior in comparison to standard high energy material - tetryl (detonation velocity of TNBD - 7727 m/s; detonation pressure - 278 kbar; tetryl – 7570 m/s and 226.4 kbar at 1.614 g/cm3, or 260 kbar at higher density - 1.71 g/cm3. The obtained preliminary results might suggest TNBD can be a potential thermostable high energy and density material (HEDM).

The effects of different pulse frequencies on the microstructure grain size and solid solubility of Al-9Si alloy were systematically investigated using OM, SEM, and EDS. The effects on the mechanical properties of the alloy were analyzed using micro-Vickers hardness tester and multifunctional friction tester. During the solidification process, the Al-9Si alloy is exposed to high-frequency electric current pulses with a current density of 300A/cm2 and frequencies of 0Hz, 500Hz, 1 000Hz, and 2 000Hz. The experimental results show that as the high-frequency pulse frequency increases, the Lorentz force also increases. The intense electromagnetic stirring leads to grain refinement. However, as the pulse frequency continues to increase, the combined effect of Joule heating and Lorentz force results in an enlargement of the melt zone and an increase in grain size. At a pulse frequency of 1 000Hz, the eutectic structure size of the Al-9Si alloy is optimal, with the average size reduced to 13.87μm and a dense distribution, effectively eliminating primary Si. The EDS results revealed that the high-frequency pulse led to a more uniform distribution of Si elements within the matrix, and the solid solubility of Si in the α-Al matrix increased to a maximum value of 1.99%, representing a 39.2% increase. At a pulse frequency of 1 000Hz, the sample demonstrates the most favorable mechanical properties, with the friction coefficient reaching a minimum value of 0.302, representing a 37.7% decrease in the average friction coefficient. The results demonstrate that high-frequency pulsing is an effective method for enhancing the mechanical properties of Al-9Si alloy.

A review is here provided about the thermal effects on the optical chirality. To this goal, chiral objects dispersed in an embedding fluid are examined for their magnetoelectric coupling. Thermal effects on several chiral meta-atoms and their ensembles are examined. To this goal, DNA-like helical structures are examined in detail. Mechanical aspect of thermo-elasticity is reviewed along with transverse deformations, while drawing analogies from condensed-matter physics. In this respect, chirality-induced spin selection is reviewed along with the temperature-mediated elec-tron-phonon interactions. A wide range of materials such as polymers and biological cells are also examined for temperature effects. A transition temperature delineating a sign flip in the chirality parameter is identified as well. Chirality-associated functionalities such as ratchet motions, switching, and modulations are investigated for their respective thermal effects. Issues of fabri-cating chiral meta-atoms are also discussed.

High temperature Ni-superalloys are limited by reliance on critical elements and complex processing steps. High entropy alloys (HEAs) have demonstrated stable single/dual phase microstructures with strong ordering tendencies. A dual phase (FCC+BCC) Al0.5Co0.5CrFeNi1.5Ti0.25 alloy (developed using CALPHAD) was tested for room and high temperature compression behavior. The microstructure mainly comprises of coarse ordered FCC(L12) surrounding decomposed lamellae of ordered FCC(L12) and BCC(L21) phases, which coarsened upon annealing at high temperature (1100 °C) into a bi-continuous structure of disordered FCC+BCC(B2). Additionally, cold rollability of the cast alloy increased from &lt;5% to ~40% after annealing, with a corresponding softening observed in room temperature compression mainly due to disordering of FCC and BCC phases. Peak flow stresses of 793.45MPa, 535.12MPa, and 324.40MPa were achieved at 800oC, 900oC, and 1000oC respectively for the high temperature annealed alloy.

This paper analyses the viability of different solutions to passively augment the axial stiffness of a horizontal axis radial levitation passive magnetic bearing (PMB) with topology previously studied. The zero-field cooling (ZFC) of high-temperature superconductor (HTS) bulks promotes higher magnetic impulsion and levitation forces and lower electromagnetic losses than with the field-cooling (FC), but on the other hand, the guiding stability is much lower than with FC. Because of stability reasons, FC was adopted in most superconducting maglev systems. The trend of this research group has been to develop an HTS ZFC horizontal axis radial levitation PMB presenting notable levitation forces with reduced electromagnetic losses, defined by a topology that creates guiding stability. Previous work has shown that even optimizing the bearing geometry to maximize magnetic guidance forces, could not be enough to guarantee the axial stiffness required for many applications. First, the extent to which guidance forces are augmented by increasing the number of HTS bulks in the stator is evaluated. Then, the axial stiffness augmentation by passively adding two limiting permanent magnet (PM) rings is evaluated. Results show that the axial stiffness is highly augmented by adding limiting PM rings with no significant additional investment. This change enables using the studied ZFC superconducting PMB in high-precision axial stability applications, such as precision gyroscopes, horizontal axis propellers and turbines.

The response of the Cold-Electron Bolometers (CEBs), integrated into a 2-D array of dipole antennas, has been measured by irradiation from YBa$_2$Cu$_3$O$_{7-\delta}$ (YBCO) 50 $\mu$m long Josephson junction into the THz region at frequencies from 0.1 to 0.8 THz. The possibility of controlling the amplitude-frequency characteristic is demonstrated by the external magnetic field in the traveling wave regime of a long Josephson junction. YBCO junction has been formed on the bicrystal Zr$_{1-x}$Y$_x$O$_2$ (YSZ) substrate by magnetron sputtering and etching of the film. CEBs have been fabricated using an Al multilayer structure by a self-aligned shadow evaporation technique on Si substrate. Both receiver and oscillator have been located inside the same cryostat at 0.3K and 2.7K plates, respectively.

The aim of this study was to investigate and effect of application of different conditions of freeze-drying on the kinetics of process and the sorption properties of dried apples. Slices of apple were frozen and subjected to freezing-drying process with different combination of a shelf temperature (-20, 10, 20, 30°C) and pressure (37, 63, 103, 165 Pa). During the freeze-drying, the temperature in the centre of material was recorded. The moisture content in dried material and changes of water content dried apples stored at humidity of 75.3% were obtained. The Midilli et al. model was used to describe drying kinetics of the freeze-drying with good fit. Drying time decreased from 660 (variant with a constant shelf temperature of 30°C, pressure 63 Pa) to 1305 minutes (variant with temperatures −20: 10: 20: 30°C, pressure 63 Pa). For this reason, the most favourable experimental parameters were: temperature of 30°C and pressure of 63 Pa. However, application of these parameters caused higher absorption of water vapour during storage. Therefore, the selection of freeze-drying parameters should also be related to the expected properties of the final product.

We report herein high-resolution x-ray diffraction measurements of basal plane bending of homoepitaxial single-crystal diamond (SCD). The results reveal that growth parameters such as temperature, growth time and basal plane bending of the substrate affect the basal plane bending of SCD. First, the basal plane bending of SCD depends mainly on the substrate itself. The basal plane bending of SCD becomes more severe with increasing basal plane bending of the substrate and this type of basal plane bending cannot be recovered. The SCD growth experiments show that the basal plane bending increases at high temperature and with increasing growth time. Finally, to understand the mechanism behind basal plane bending, we investigate the substrate-surface temperature distribution as a function of basal plane bending of SCD fabricated by chemical vapour deposition (CVD). This allows us to propose a bending model and understand the origin of basal plane bending. The results indicate that an uneven temperature distribution on the substrate surface is the main cause of the CVD diamond base-plane bending.

Carbon fiber-reinforced polymer (CFRP), noted for its outstanding properties including high specific strength and superior fatigue resistance, is increasingly employed in aerospace and other demanding applications. This study investigates the interactions between CFRP composites and high-energy lasers (HEL), with continuous wave laser powers reaching up to 120 kW. A novel automated sample exchange system, operated by a robotic arm, minimizes human exposure while enabling a sequence of targeted laser tests. High-speed imaging captures the rapid expansion of a plume consisting of hot gases and dust particles during the experiment. The research significantly advances empirical models by systematically examining the relationship between laser power, perforation times, and ablation rates. It demonstrates scalable predictions for the effects of high-energy laser radiation. Detailed examination of the damaged samples, both visually and via micro-focused computed X-ray tomography, offers insights into heat distribution and ablation dynamics, highlighting the anisotropic thermal properties of CFRP. Compression-after-impact (CAI) tests further assess the residual strength of the irradiated samples, enhancing the understanding of CFRP’s structural integrity post-irradiation. Collectively, these tests improve the knowledge of the thermal and mechanical behavior of CFRP under extreme irradiation conditions. The findings not only contribute to predictive modeling of CFRP's response to laser irradiation but also enhance the scalability of these models to higher laser powers, providing robust tools for predicting material behavior in high-performance settings.

Fat reduction and anti-inflammation are commonly claimed properties of probiotics. Lactobacillus plantarum and Enterococcus faecium were tested in high fat-induced obesity mice and in vitro experiments. After 16 weeks of probiotics, L. plantarum outperforms E. faecium on the anti-obesity property as indicated by body weight, regional fat accumulation, serum cholesterol, inflammatory cytokines (in blood and colon tissue), and gut barrier defect (FITC-dextran assay). With fecal microbiome analysis, L. plantarum but not E. faecium reduced fecal abundance of pathogenic Proteobacteria without an alteration in total Gram-negative bacteria when compared with non-probiotics obese mice. With palmitic acid induction, the condition media from both probiotics similarly attenuated supernatant IL-8, improved enterocyte integrity and down-regulated cholesterol absorption-associated genes in Caco-2 cell (an enterocyte cell line) and reduced supernatant cytokines (TNF-α and IL-6) with normalization of cell energy status (extracellular flux analysis) in bone-marrow-derived macrophages. Because the anti-inflammatory effect of the condition media of both probiotics on palmitic acid-activated enterocytes was neutralized by amylase, the active anti-inflammatory molecules might, partly, be exopolysaccharides. As L. plantarum out-performed E. faecium in anti-obesity property, possibly through the reduced fecal Proteobacteria, with a similar anti-inflammatory exopolysaccharide; L. plantarum is a potentially better option for anti-obesity than E. faecium.

We investigated the effect of 0.6 MeV proton irradiation on the superconducting and normal state properties of thin-film YBa2Cu3O7−δ superconductors. A thin-film YBCO superconductor (≈ 567 nm thick) was subject to a series of proton irradiations with a total fluence of 7.6×1016p/cm2. Upon irradiation, Tc was drastically decreased from 89.3 K towards zero with a corresponding increase in its normal state resistivity above Tc. This increase in resistivity which indicates the increase of defects inside the thin-film sample can be converted to the dimensionless scattering rate. We found that the relation between Tc and dimensionless scattering rate obtained during proton irradiation approximates the generalized d-wave Abrikosov-Gor’kov theory better than the previous results obtained from electron irradiations. This is an unexpected result since the electron irradiation is known to be most effective to suppress superconductivity over other heavier ion irradiations such as proton irradiation. It suggests that the type of defects created by proton irradiation evolves from cascade defects (in bulk single crystals) to point-like defects (in thin-film single crystals) as the thickness decreases.

The utilization of selective laser melting (SLM) for high entropy alloys (HEAs) holds significant promise in commercial applications, and substantial experimental research efforts have been directed toward this domain. To take advantage of the reported experimental data of SLM manufactured (SLM-ed) HEAs and reduce unnecessary experimentation, this study incorporates machine learning (ML) techniques for the phase and tensile properties prediction of SLM-ed HEAs, thus presenting a novel avenue for accelerating the discovery of new SLM-ed HEAs. Through the adjustment of material descriptors and machine learning models, a model has been developed with an impressive accuracy of 93.8% in distinguishing between face-centered cubic (FCC), body-centered cubic (BCC), and dual-phase (FCC+BCC). Additionally, optimized models have been devised for the prediction of tensile properties, namely ultimate tensile strength (UTS), yield strength (YS), and elongation (δ), achieving noteworthy MAPEs (mean absolute percentage errors) of 10.33%, 8.55%, and 28.48%, respectively. Furthermore, several HEAs were fabricated using SLM, and the experimental outcomes exhibited a favorable alignment with the predicted results. These efforts carry significant implications in advancing the utilization of SLM for HEAs.

This research investigates the fatigue behaviour and fracture mechanics of high-performance concrete (HPC), including various compositions such as HPC with basalt aggregates (HPC-B), HPC with gravel (HPC-G), and high-strength coarse mortar (CM) static and cyclic tensile loading within the special priority program SPP 2020. The study aims to integrate fracture mechanics into structural analysis to enhance design guidelines for slender cross-sections and safety-related high-performance structural components. The experimental investigations reveal HPC-B's re-markable superiority, displaying higher compressive strength, modulus of elasticity, and tensile strength compared to HPC-G and CM. A modified disk-shaped compact tension (MDCT) based on ASTM standards, aided by digital image correlation (DIC) unveils fracture behaviour, empha-sizing fracture energy as a crucial parameter. HPC-B exhibits improved crack resistance and notch sensitivity reduction attributed to crushed basalt aggregates and enhanced interfacial transition zone (ITZ). The research scrutinizes factors like material characterization, aggregate morphology, stress levels, and displacement rate on crack formation. High-cycle fatigue tests show HPC-B's superior performance, and post-fatigue analysis reveals enhanced residual fracture toughness attributed to nano-level structural changes, stress redistribution and aggregate-matrix interac-tion. 3D image analysis via Computed Tomography (CT) scans captures mesostructural crack propagation and provide quantitative insights. This study advances the understanding of HPC fatigue behaviour, emphasizing the interplay of aggregate types, morphologies, and their dy-namic response to cyclic loading, offering valuable insights for optimizing design guidelines and fostering innovation in structural engineering.

The study focuses on a novel porous TiNi-based material for ophthalmic orbital implants which was produced by self-propagating high-temperature synthesis (SHS) and, after proper surface modification, possesses a specific microstructure of its surface pores, which makes it attractive for biomedical use in implants. After preparation via SHS, the obtained porous TiNi material was etched in acidic environment, to get rid of its surface Ti2Ni secondary-phase particles. This was found to improve the material’s surface morphology, adding micro-roughness to its macro-rough pores. As a result, cell growth tests conducted on the material demonstrated improved cell adhesion and growth kinetics on such a porous material with improved roughness. Finally, the material was tested in vivo as an ophthalmic orbital implant, demonstrating good biocompatibility, good degree of biointegration with surrounding eyeball tissues, and no signs of rejection after as long as 180 days. Thus, the novel porous TiNi-based material shows promise for its use in ophthalmic implantology, for instanse for manufacturing musculoskeletal stumps of the eyeball after evisceration, as it is biocompatible, has a high tissue-implant integration potential and demonstrates reduced risks of exposure and rejection of the implant.

This work deals with a novel porous TiNi-based material for ophthalmic orbital implants that was produced by high-temperature synthesis (SHS) and possesses a specific microstructure of its surface pores, which makes it attractive for biomedical use in implants. After preparation via SHS, the obtained porous TiNi material was etched in acidic environment, to get rid of its surface Ti2Ni secondary-phase particles. This was found to improve the material’s surface morphology, adding micro-roughness to its macro-rough pores. As a result, cell growth tests conducted on the material demonstrated improved cell adhesion and growth kinetics on such a porous material with improved roughness. Finally, the material was tested in vivo as an ophthalmic orbital implant, demonstrating good biocompatibility, good degree of biointegration with surrounding eyeball tissues, and no signs of rejection after as long as 180 days. Thus, the novel porous TiNi-based material shows promise for its use in ophthalmic implantology, for instanse for manufacturing musculoskeletal stumps of the eyeball after evisceration, as it is biocompatible, has a high tissue-implant integration potential and demonstrates reduced risks of exposure and rejection of the implant.

A pilot study on laser 3D printing of inorganic free-form micro-optics is experimentally validated. Ultrafast laser nanolithography is employed for structuring hybrid organic-inorganic material SZ2080TM followed by high-temperature calcination post-processing. The combination allows production of 3D architectures and the heat-treatment results in converting the material to inorganic substance. The produced miniature optical elements are characterized and their optical performance demonstrated. Finally, the concept is validated for manufacturing compound optical components such as stacked lenses. This is opening for new directions and applications of laser made microoptics under harsh conditions such as high intensity radiation, temperature, acidic environment, pressure variations, which include open space, astrophotonics, and remote sensing.

A twin-screw extruder was used to fabricate poly(butylene succinate) (PBS)/high density polyethylene (HDPE) blends (7:3 weight ratio) and blend-based nanocomposites. Carbon nanotubes (CNTs), graphene nanoplatelets (GNPs) and organoclays (15A and 30B) served as the nanofiller, while maleated HDPE (PEgMA) acted as an efficient compatibilizer for the blend. In the composites, individual nanofillers were mostly localized in HDPE domains, but some fillers were also observed at PBS-HDPE interfaces. The sea-island morphology of compatibilized blend evolved into a pseudo-co-continuous morphology in the composites. Differential scanning calorimetry results confirmed that PEgMA with HDPE evidently accelerated the crystallization of PBS in the blend. The possible nucleation effect of added fillers on PBS crystallization was obscured by the formation of quasi-connected HDPE domains, causing less PBS nucleation sites. The presence of nanofillers improved the thermal stability and burning anti-dripping behavior of the parent blend. The anti-dripping efficiency of added fillers followed the sequence: CNT>15A>30B>GNP. Rigidity of the blend was increased after formation of nanocomposites. In particular, adding GNP resulted in 31% increase in flexural modulus. Development of a pseudo-network structure in the composites was confirmed by measurement of rheological properties. Electrical resistivity of the blend was reduced by more than 6 orders of magnitude at 3 phr CNT loading, demonstrating the achievement of double percolation morphology.

Foot lesions are among the most frequent causes of morbidity and disability in the diabetic population. Thus, exploration of means of preventive control are vital for detecting early signs and symptoms of this disease, Infrared thermography has been proven effective in the control of diabetic foot is among the complementary diagnostic tools available for this disease. The last review on this topic was published in 2015 and so, here we conducted a bibliographic review of the main databases (PubMed, the Web of Science, Cochrane library, and Scopus) during the third quarter of 2023. We aimed to identify the effectiveness of infrared thermography as a diagnostic element in pre-ulcerous states in diabetic patients and to detect diabetic foot ulcer complications. We obtained a total of 200 articles, 22 of which were included in this present review; 17 articles had been published after 2017. After analysing the use of infrared Thermography in diabetic patients both with and without ulcers, as well as in healthy individuals, we concluded that is an effective tool for detecting early-stage ulcers in diabetic foot patients.

A semi-analytical approach is developed for predicting pyrolysis front temperature in a solid undergoing thermal decomposition. The pre-reaction heating stage is described using an analytical formulation and invoking the concept of thermal penetration depth. The solution for the solid conversion stage accounts for decomposition enthalpy, convective flow of volatiles, and a reaction front characterized by a uniform temperature that progresses toward the inner layers. This method incorporates empirical relations into the analytical model. Two scenarios are considered. First, the solution of the pyrolysis model combined with the data of conversion time versus external heat flux leads to an algebraic expression that reveals the existence of a maximum pyrolysis-front temperature. Explicit relations are derived for both the extremum pyrolysis temperature and optimum applied heat flux. In the second case, an expression is derived for the ignition temperature of a solid fuel by incorporating ignition delay time measurements into the heating stage model. The newly derived expression allows to describe the ignition temperature as a function of the Biot number and external heat flux. The relation obtained for the ignition temperature explains the experimental trends reported in some previous studies where two local extremums were observed for the ignition temperature in the absence of volatiles reactions.

EV transmissions operate at high speeds, upto 30,000 rpm. High speed operation puts higher demands on bearings, seals, and gears. Bearings in EV transmissions are prone to electrically induced bearing damage and may exhibit signs of pitting and fluting. Surface-initiated rolling contact fatigue is another common problem gaining increased attention lately. Most EV transmissions require a coupling between an oil-lubricated gearbox to an electrical motor that runs with minimal lubrication at very high rpm. High mechanical and thermal stresses the seals are exposed to under starved lubrication conditions have a detrimental impact on their service life. Hence, proper lubrication is critical. In general, EV transmission fluids call for a somewhat different spectrum of properties compared to conventional ATF. Gear tribology simulations open new ways to the design and optimization of lubrication for EV transmissions. Additionally, such simulations can also provide valuable insights into the effects of different oil properties on cooling and lubrication efficiencies, thereby helping in matching the lubricant and hardware characteristics for optimal performance. In the present communication, we demonstrate the effects of different lubricants and surface finishing technologies on the tribology of high-speed gears using tribological tests and advanced thermal elastohydrodynamic (TEHD) simulations. Important roles of lubricity additives and surface finish optimization are highlighted in conjunction with a move towards ultralow viscosity EV transmission fluids.

Optical characterization and thermal aging tests are performed on a sputter-deposited coating, consisting of SiO₂/Cr₂O₃/Cr/Cr₂O₃ layers, designed and developed as a selective solar absorber to be used for unconcentrated solar thermal applications. Both measurements are performed by using a home-made apparatus, which mimics a flat plate collector under high vacuum. A Performance Criterion (PC_η(T)), based on absorber efficiency is proposed, and a forecast of service lifetime is obtained. As a result of the thermal aging tests, the selective solar absorber under study appears to be highly efficient at mid temperatures (up to 573 K) and thermally stable at temperatures (up to 690 K).

Super duplex stainless steel (SDSS) is used for manufacturing large valves and pipes in offshore plants because of its excellent strength and corrosion resistance. Large valves and pipes are manufactured by forging after casting, and the outside and inside microstructures are different owing to the difference in the cooling rate caused by the thermal conductivity. This microstructural variation causes cracks during solution annealing, which breaks the materials. To study toe corrosion resistance of the SDSS forged material, the microstructure was conducted based on the difference in the cooling rate between the inside and outside of the cast SDSS. To analyze the effects of the secondary phase fraction before solution annealing on the solution and corrosion resistance, the corrosion resistance with and without solution annealing was measured using the potentiodynamic polarization test and critical temperature test after the precipitation of the secondary phase. In the potentiodynamic polarization test, the secondary phase decreased the activation polarization and increased the corrosion rate. The critical pitting temperature exhibited the effect of the secondary phase.

Chilean jack mackerel (Trachurus murphyi) is recognized as one of the most valuable pelagic resources across the southeast Pacific Ocean. Despite its nutritious properties it is an underused resource due to its rapid spoilage. The use of high hydrostatic pressure (HHP) for the processing of aquatic products could be an efficient alternative to cold storage since HHP might inactivate microbial pathogens and slow down spoilage microorganisms, therefore extending the product’s shelf life. The aim of the study was to compare the effect of HHP at 450 and 550 MPa for 3 min on the physicochemical properties of jack mackerel muscle undergoing pre- and post-rigor mortis stage and further storage for 26 days at 4°C. pH, total volatile basic nitrogen, trimethylamine, color, water-holding capacity, and texture were assessed. The proximate composition, pH, total volatile basic nitrogen, trimethylamine, color, water holding capacity, and texture, showed significant changes between untreated and treated samples, while the water holding capacity was virtually unaffected. Overall results showed an acceptable and long-lasting edible quality of Trachurus murphyi stored at 4°C when preserved through HHP. These findings suggest that the HHP might be able to industrially scale the production of highly physicochemical superior and minimally processed fish products.

Aiming to diminish the defects caused by high-speed pulsed GMAW welding, such as non-penetration, non-fusion, humping and undercut, the paper proposed an improved twin-wire double-pulsed high-speed welding process by introducing the impact of additional shielding gas on the welding pool and the effects of different shielding gas flowrates on the microstructure and mechanical properties of the welded seam was investigated. The 2205 duplex stainless steel plate was used as the base material for the butt welding test, and the welded seams were subjected to tensile test, metallographic analysis, hardness analysis, and nondestructive testing. The results indicate that as the flowrate of additional shielding gas increases in the range of 8 L/min~16 L/min, the width of the welded seam increases and the height of reinforcement decreases gradually. However, a grooved seam with a lower middle region and higher sides will appear when the gas flowrate becomes excessively large. The test results indicate that the jet impact force is relatively moderate when the flowrate of the additional shielding gas is 12 L/min and thus, is optimal for the welded seam.

Pyrochlore oxides (A2B2O7) are potential nuclear waste substrate material due to their superior radiation resistance properties. We performed molecular dynamics simulations to study the structural properties and displacement cascades in ytterbium titanate pyrochlore (Yb2Ti2O7). We computed threshold displacement energy ( Ed ) and lattice constant ( ao) of Yb2Ti2O7. The effect of displacement cascades in Yb2Ti2O7 of recoils of energies 1 keV, 2 keV, 5 keV, 10 keV in different crystallographic directions ([100], [110], [111]) were studied. The number of defects is found to be proportional to the energy of incident PKA. Additionally, the Ed of pyrochlore is computed and it exhibits anisotropy. Furthermore, radiation damage in high-entropy pyrochlore (HEPy) i.e., YbYTiZrO7, YbGdTiZrO7 , Yb0.5Y0.5Eu0.5Gd0.5TiZrO7 were investigated and compared with Yb2Ti2O7. It was found that HEPy have a larger Ed as compared with Yb2Ti2O7 which exhibits characteristic of lower radiation damage resistance than HEPy. Our simulation proposed that HEPy alloys are more radiation resistant than individual pyrochlore constituents . This work will provide atomic insights in developing substrate materials for nuclear waste applications.

This research investigates the impact of Al and Ti elements on the formation of self-generated ordered phase in high-entropy alloys (HEA), which have been receiving widespread concentration in present times thanks to their remarkable multifunctional properties and wide range of component selection. By adjusting the dual elements of Al and Ti, the study explores the regulation of quantity and distribution of the in-situ self-generated ordered phases in the alloy. The results of the annealing heat treatment process demonstrated that, through accession Al and Ti elements, the Cr-Fe-Ni medium-entropy alloy transfer from BCC phase to BCC+FCC phase and the precipitation of new phases such as B2, L21, and σ. This led to a synergistic impact of second phase strengthening, and also of solid solution strengthening, resulting in improved compressive properties of HEA.

Low-temperature processed ITO thin films offer the potential of overcoming the doping limit by suppressing the equilibrium of compensating oxygen interstitial defects. To elucidate this potential, electrical properties of Sn-doped In₂O₃ (ITO) thin films are studied in dependence on film thickness. In-operando conductivity and Hall effect measurements during annealing of room temperature deposited films with different film thickness in different environments allow to discriminate between the effects of crystallization, grain growth, donor activation and oxygen diffusion on carrier concentrations and mobilities. At 200 °C, a control of carrier concentration by oxygen incorporation or extraction is only possible for very thin films. The electrical properties of thicker films deposited at room temperature are mostly affected by grain size. The remaining diffusivity of compensating oxygen defects at 200 °C is sufficient to screen the high Fermi level induced by deposition of Al₂O₃ using atomic layer deposition (ALD), which disables the use of defect modulation doping at this temperature. The results indicate that achieving higher carrier concentrations requires a control of the oxygen pressure during deposition in combination with seed layers to enhance crystallinity or the use of near room temperature ALD.

A novel hybrid CSP-PV power plant is presented. Instead of the integration used in current hybrid power plants, where part of the PV production is charged into the thermal energy storage system through electrical resistors, the proposed system integrates both PV and thermal solar fields using a high-temperature heat pump. Both the heat pump and the heat engine are based on Brayton supercritical CO2 thermodynamic cycles. Such integration allows for charging the molten salts storage as if a central tower receiver field supplied the thermal energy, whereas parabolic trough collectors are employed. Unlike conventional hybrid plants, where the storage of PV production leads to a decrease in power injected into the grid throughout the day, the power injected by the proposed system remains constant. The heat engine efficiency is 44.4%, and the COP is 2.32. The LCOE for a 50 MWe plant with up to 12 hours of storage capacity is 171 $/MWh, which is lower than that of existing CSP power plants with comparable performance. Although the cost is higher compared to a PV plant with batteries, this hybrid system offers two significant advantages: it eliminates the consumption of critical raw materials in batteries, and all the electricity produced comes from a synchronous machine.

For the first time, few-layer graphene (FLG) nanosheets were synthesized by the method of self-propagating high-temperature synthesis (SHS) from biopolymers (starch and lignin). We suggested that biopolymers (lignin, tree bark) and polysaccharides, in particular starch, could be an acceptable source of native cycles for the SHS process. The carbonization of biopolymers under the conditions of the SHS process was chosen as the basic method of synthesis. Chemical reactions, under the conditions of the SHS process, proceed according to a specific mechanism of nonsothermal branched-chain processes, which are characterized by the joint action of two fundamentally different process-accelerating factors - avalanche reproduction of active intermediate particles and self-heating. The method of obtaining FLG nanosheets included the thermal destruction of hydrocarbons in a mixture with an oxidizing agent. We used biopolymers as hydrocarbons and ammonium nitrate as an oxidizing agent. Thermal destruction was carried out in the mode of SHS, heating the mixture in a vessel at a speed of 20–30 oC/min to 150-200 oC and keeping at this temperature for 15–20 min with the discharge of excess gases into atmosphere. A combination of spectrometric research methods, supplemented by electron microscopy data, has shown that the particles of the carbonated product powder in their morphometric and physical parameters correspond to FLG nanosheets. An X-ray diffraction analysis of the indicated FLG nanosheets was carried out, which showed the absence of formations with a graphite crystal structure in the final material. The surface morphology was also studied and the features of the IR absorption of FLG nanosheets were analyzed. It is shown that the developed SHS method makes it possible to obtain FLG nanosheets with linear dimensions of tens of microns and a thickness of not more than 1-5 graphene layers (several graphene layers).

Climate change is expected to increase the frequency and severity of abiotic stresses that lead to loss of crop yield. We investigated the effect of salinity (S), short episodes of high temperature (HS) and combination of S+HS at the reproductive phase on dead pericarps properties and yield of the crop plant Brassica juncea. Three intervals of HS resulted in massive seed abortion; seeds from salt-treated plants germinated poorly. Pericarp extracts of salt-treated plants reduced seed germination of B. juncea; all pericarp extracts completely inhibited seed germination of tomato and Arabidopsis; removal of pericarp extracts restored seed germination. HS reduced all metabolites accumulated in dead pericarps, except for upregulation of isomaltose and cellobiose. Salt induced alteration in metabolite levels including increase in proline, reduction in TCA intermediates and changes in phytohormone levels. Proteome analysis revealed hundreds of proteins stored in dead pericarps whose levels and composition were altered under salt stress. The integration of metabolic and proteomic data showed that changes in metabolites were highly correlated with changes in proteins involved in their biosynthetic pathways. Thus, besides providing a physical shield for seed/embryo protection dead pericarps store beneficial substances whose levels, composition and biological function are altered under stress, further highlighting the elaborated function of dead organs enclosing embryos in seed biology and ecology. The detrimental effect of HS on crop production might have implications for global food security in the face of climate change.

Void fillers are required for osseous gaps generated after orthopedic procedures as medial open-wedge high-tibial osteotomy (MOWHTO) to provide sufficient structural support and a rapid osteosynthesis. We developed a novel three-dimensional (3D) printing-based platform technology using the customized 3D scaffolds covered with polycaprolactone (PCL)/β-tri-calcium phosphates (β-TCP)/bone decellularized extracellular matrix (dECM) for use as bone substitute scaffold, which can be effectively exploited to estimate the calculated correction angle with preoperative simulations. PCL/β-TCP/bone dECM scaffolds demonstrated significantly higher cell contain levels in cell seeding efficiency, excellent proliferation capacity, and promotion of early osteogenic differentiation compared with PCL/β-TCP scaffolds. The scaffolds promoted bone mineralization at the early time points of an in vivo study (8 weeks) and exhibited biodegradable properties (38% for 16 weeks). The correction angle measured after osteotomy using 3D printed scaffolds was estimated with high accuracy with low errors (10.3° ± 0.9°), was and was not significantly different even in the presence of lateral cortical hinge fractures. The customized 3D scaffold enriched with PCL/β-TCP/bone dECM yielded excellent cell seeding efficiency, proliferation capacity, early osteogenic differentiation, and bone mineralization outcomes. It is expected to solve the disadvantages related with bone union in MOWHTO, and to replace autografts in the future.

In regions with low-temperature action transverse cracks can appear in asphalt pavements as a result of thermal stresses that exceed the fracture strength of materials used in asphalt layers. To better understand thermal cracking phenomenon, strength properties of different asphalt mixtures were investigated. Four test methods were used to assess the influence of bitumen type and mixture composition on tensile strength properties of asphalt mixtures: tensile strength using the Thermal Stress Restrained Specimen Test (TSRST) and the Uniaxial Tension Stress Test (UTST), flexural strength using the Bending Beam Test (BBT) and fracture toughness using the Semi-Circular Bending Test (SCB). The strength reserve behavior of tested asphalt mixtures was assessed as well. The influence of cooling rate on strength reserve was investigated and correlations between results from different test methods were also analyzed and discussed. It was observed that the type of bitumen is a factor of crucial importance to low-temperature properties of the tested asphalt concretes. This conclusion was proved by all test methods that were used. It was also observed that the level of cooling rate influences the strength reserve and, in consequence, resistance to low-temperature cracking. It was concluded that reasonably good correlations were observed between strength results for the UTST, BBT and SCB test methods.

This research paper focuses on the synthesis and characterization of Cu-doped Mg-Co ferrites with varying compositions (Mg_0.6-xCo_0.4Cu_xFe₂O₄, where x = 0.0, 0.1, 0.2, and 0.3) using a solid-state reaction method. This paper also investigates the structural, morphological, magnetic, and electrical characteristics of synthesized Mg_0.6-xCo_0.4Cu_xFe₂O₄, where x = 0.0, 0.1, 0.2, and 0.3. The X-ray diffraction (XRD) technique confirms the ferrites spinel structure in the Fd-3m space group, with average crystallite sizes ranging from 57.29 to 48.57 nm. Fourier Transform Infrared (FTIR) spectroscopy verifies chemical and structural changes, while scanning electron microscopy (SEM) reveals cubic crystal growth with an average grain size of 1 to 1.5 μm. DC electrical resistivity decreases with increasing temperature and Cu²⁺ substitution, ranging from 1.4 x 10⁶ Ω-cm to 6.7 x 10⁵ Ω-cm. The study suggests a correlation between resistivity and Cu²⁺ concentration. Magnetic behaviour, studied using a Vibrating Sample Magnetometer (VSM), shows dependence on dopant concentration, with coercivity ranging from 157 Oe to 256 Oe. The results indicate potential applications in magnetic storage devices, antennas, transformers, and high-frequency electronics.

A quantitative method is proposed to determine of Stone-Wales defects for carbon nanostructures with sp2 hybridization of carbon atoms. The technique is based on the diene synthesis reaction (Diels-Alder reaction). The proposed method was used to determine Stone-Wales defects in the few-layer graphene (FLG) nanostructures synthesized by the self-propagating high-temperature synthesis (SHS) process, in reduced graphene oxide (rGO) synthesized based on the method of Hammers and in the single-walled carbon nanotubes (SWCNT) TUBAL trademark, Russia. Our research has shown that the structure of FLG is free of Stone-Wales defects, while the surface concentration of Stone-Wales defects in TUBAL carbon nanotubes is 1.1×10-5 mol/m2 and 3.6×10-5 mol/m2 for rGO.

A metastable β-Ti alloy, Ti–10V–3Fe–3Al (wt.%), was subjected to thermos-mechanical processing including the compression test at 725°C, which is below the β transus temperature (780°C), and at strain rate of 10-3s-1. The presence of phases was determined using transmission electron microscopy and X-ray diffraction. Although the dynamic recovery took place together with slip, both deformation-induced α˝ martensite and ω were detected as other operating mechanisms for the first time in metastable-β Ti alloys deformed in α+β region. The volume fraction of stress-induced α˝ was higher than that of the same alloy deformed at room temperature due to higher strain applied. Stress-induced twinning was not operational, which could be related to the priority of slip mechanism at high temperature resulted from thermally-assisted nucleation and lateral migration of kink-pairs.

Knowledge of the temperature evolution is crucial to understand and control laser beam welding of low-melting materials. Existing temperature determination approaches are restricted to i) one-dimensional temperature information (e.g. ratio-pyrometers), ii) a priori knowledge of the emissivity (e.g. thermography) and iii) high temperature regions (e.g. two-wavelength imaging). In this paper, a ratio-based two-color-thermography approach is developed that allows for two-dimensional temperature determination in low-melting temperature ranges (< 1200 K). For static measurement situations it is demonstrated, that temperature can be determined despite variation in signal intensity and emissivity with high accuracy. The two-color-thermography set-up is further transferred into a commercial laser beam welding machine and experiments are conducted for varying process parameters. The direct application of the developed two-color-thermography system in dynamic process situations is limited as image artifacts presumably caused by internal reflections inside the optical beam path are present.

Abstract: Mass spectrometry research laboratories reported multiple probes for ambient ionization in the last years. Combining them with a mechanical moving stage enables automated sampling and imaging applications. We developed a robotic platform, which is based on RepRap 3D-printer components, and therefore easy to reproduce and to adopt for custom prototypes. The minimal step width of the Open LabBot is 12.5 μm, and the sampling dimensions (x, y, z) are 18 × 15 × 20 cm. Adjustable rails in an aluminium frame construction facilitate the mounting of additional parts such as sensors, probes, or optical components. The Open LabBot uses industry-standard G-code for its control. The simple syntax facilitates the programming of the movement. We developed two programs: 1) LABI-Imaging, for direct control via a USB connection and the synchronization with MS data acquisition. 2) RmsiGUI, which integrates all steps of mass spectrometry imaging: The creation of G-code for robot control, the assembly of imzML files from raw data and the analysis of imzML files. We proved the functionality of the system by the automated sampling and classification of essential oils with a PlasmaChip probe. Further, we performed an ambient ionization mass spectrometry imaging (AIMSI) experiment of a lime slice with laser desorption low-temperature plasma (LD-LTP) ionization, demonstrating the integration of the complete workflow in RmsiGUI. The design of the Open LabBot and the software are released under open licenses to promote their use and adoption in the instrument developers’ community.

We use the Stefan-Boltzmann law to derive and investigate what we will call the black hole CMB temperature luminosity. Interestingly, the CMB luminosity is always the same for every black hole at a luminosity distance equal to the Schwarzschild radius, which is fully valid in black hole cosmology, a topic that is actively discussed to this day. The CMB black hole luminosity is always the same , regardless of the mass of the black hole. This is in contrast to the Bekenstein-Hawking luminosity, which is linked to the Hawking temperature, that is mass dependent.

Pakistan relies mostly on fossil fuel for fulfilling its energy demand which is expensive as 11 well as not friendly for the environment. The need of the hour is to shift from fossil fuels to renew-12 able energy resources like geothermal, wind, solar etc. to cater for global warming issues. Pakistan 13 has a lot of potential geothermal sites because of several fault lines and hot springs. A sound 14 knowledge of ground temperature is essential to use geothermal energy, which is obtained by drill-15 ing boreholes and putting sensors making it an expensive procedure. Thus, to avoid huge cost for 16 drilling bore holes, particularly for ground temperature analysis, a numerical approach has been 17 considered for determining ground temperature. Furthermore, correlation charts between air and 18 ground temperatures have been developed as there were no proper studies on the ground temper-19 ature of Pakistan. Then, with the help of a boreholes drilled in National University of Sciences and 20 Technology Islamabad Pakistan, the actual ground and numerically calculated temperatures have 21 been compared which shows an error margin in the range between 0.27% for higher depths to 7.3% 22 near surface. Thus, it is shown that the proposed method is easy to implement and better than large 23 scale testing methods for the depths at which geothermal energy is extracted.

Daily maximum surface air temperature (Tamax) is a crucial factor for understanding complex land surface processes under rapid climate change. Remote detection of Tamax has widely relied on the empirical relationship between air temperature and land surface temperature (LST), a product derived from remote sensing. However, little is known about how such a relationship is affected by the high heterogeneity in landscapes and dynamics in seasonality. This study aims to advance our understanding of the roles of land cover and seasonal variation in the estimation of Tamax using the MODIS (Moderate Resolution Imaging Spectroradiometer) LST product. We developed statistical models to link Tamax and LST in the middle and lower reaches of the Yangtze River in China for five major land-cover types (i.e., forest, shrub, water, impervious surface, cropland, and grassland) and two seasons (i.e., growing season and non-growing season). Results show that the performance of modeling the Tamax-LST relationship was highly dependent on land cover and seasonal variation. Estimating Tamax over grasslands and water bodies achieved superior performance; while uncertainties were high over forested lands that contained extensive heterogeneity in species types, plant structure, and topography. We further found that all the land-cover specific models developed for the plant non-growing season outperformed the corresponding models developed for the growing season. Discrepancies in model performance mainly occurred in the vegetated areas (forest, cropland, and shrub), suggesting an important role of plant phenology in defining the statistical relationship between Tamax and LST. For impervious surfaces, the challenge of capturing the high spatial heterogeneity in urban settings using the low-resolution MODIS data made Tamax estimation a difficult task, which was especially true in the growing season.

High dimensional statistical analysis for the yield of large-scale circuits is quite difficult due to expensive simulations, especially for the memory circuits with high sigma requirement (e.g., SRAM). In this paper, we developed an efficient sparse additive model to substitute simulations. To fit high sigma region accurately, the modeling center is moved to near failure boundary searched by scaling the shape of sampling function. To solve the model efficiently, the process variables are grouped by standard cells so that the model can be solved by our developed blockwise greedy algorithm. The experiments on the 28nm memory circuits validate that our method achieves high accuracy and efficiency compared with other state-of-art works.

Currently available data are consistent with increased severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) replication at temperatures encountered in the upper airways (25–33°C when breathing room temperature air, 25°C) compared to those in the lower airways (37°C). One factor that may contribute to more rapid viral growth in the upper airways is the exponential increase in SARS-CoV-2 stability that occurs with reductions in temperature, as measured in vitro. Because SARS-CoV-2 frequently initiates infection in the upper airways before spreading through the body, increased upper airway viral growth early in the disease course may result in more rapid progression of disease and potentially contribute to more severe outcomes. Similarly, higher SARS-CoV-2 viral titer in the upper airways likely supports more efficient transmission. Conversely, the possible significance of air temperature to upper airway viral growth suggests that prolonged delivery of heated air might represent a preventative measure and prophylactic treatment for coronavirus disease 2019.

Asphalt pavement temperature has several applications, including pavement structural design and evaluation, asphalt mixture design, asphalt binder grade determination and material aging characterization. However, available asphalt pavement temperature prediction models were mostly developed for temperate climatic conditions, outside of the tropics. Before such models are adopted for use in a tropical climate, their applicability must be evaluated. This study evaluated five empirical asphalt pavement temperature prediction models developed by Lukanen et al. [1], Park et al. [2], Diefenderfer et al. [3], Taamneh [4] all in the United States and Asefzadeh et al. [5] in Canada to ascertain their prediction accuracy in tropical climate, using Ghana as a case study. In-situ asphalt pavement temperature data were measured at two sites for eight months: Kumasi and Tamale in the Forest and Savannah climatic zones, respectively. The measured pavement temperature data were statistically compared with predicted temperatures, and it was found that the Park et al. [2] model provided a more accurate pavement temperature prediction in both climatic zones. The other models either over-predicted or under-predicted asphalt pavement temperature with significant error margins. However, there is a need to improve the prediction accuracy of the Park et al. [2] model or a local model developed.

The response of boreal vegetation to global warming has shown a weakening trend over the last three decades. However, in previous studies, models of vegetation activity responses to temperature change have often only considered changes in mean daily temperature (Tmean), with the diurnal temperature range (DTR) being neglected. The goal of this study is to evaluate the temporal trends of the relationships between two temperature factors (Tmean and DTR) and vegetation activity across the boreal regions on both annual and seasonal timescales, by simultaneously employing satellite and climate datasets. We found that the interannual partial correlation between growing season (GS) NDVI and Tmean (RNDVI−Tmean) showed a significant decreasing trend over the last 34 years. At the seasonal scale, RNDVI−Tmean shows a significant upward trend in the spring, while in the summer and autumn, RNDVI−Tmean exhibits a significant downward trend. The temporal trend characteristics of the partial correlation between NDVI and DTR (RNDVI−DTR), at both the GS and seasonal scales, are fully consistent with RNDVI−Tmean. The area with a significant decrease in GS RNDVI−Tmean and RNDVI−DTR accounted for approximately 44.40% and 41.21% of the boreal region with the 17-year moving window, respectively. In stark contrast, the area exhibiting a significant increasing trend in GS RNDVI−Tmean and RNDVI−DTR accounted for only approximately 14.65% and 13.59% of the boreal region with the 17-year moving window, respectively. With respect to the seasonal patterns of RNDVI−Tmean and RNDVI−DTR, the area with a significant upward trend in spring was greater than that with a significant downward trend. Nevertheless, more areas had a significant downward trend of RNDVI−Tmean and RNDVI−DTR in summer and autumn than had a significant upward trend. Overall, our research reveals a weakening trend in the impact of temperature on vegetation activity in the boreal regions, and contributes to a deeper understanding of the vegetation response to global warming.

The boreal Hemisphere has been experiencing increasing extreme hot and dry conditions over the past few decades, consistent with anthropogenic climate change expectations. The continental extension of the phenomenon calls for tools and techniques capable of monitoring the global to regional scales. In this context, the satellite is the only system that can satisfy the need for global coverage. The main objective we have addressed in the present paper is the capability of infrared satellite observations helping to monitor the vegetation stress due to increasing drought and heatwaves in summer. We have designed and implemented a new water deficit index (wdi) that exploits satellite observations in the infrared to retrieve humidity, air temperature, and surface temperature simultaneously. These three parameters are combined to provide the water deficit index. The index has been developed based on the Infrared Atmospheric Sounder Interferometer or IASI, which covers the infrared spectral range 645 to 2760 cm-1 with a sampling of 0.25 cm-1. The index has been used to study the 2017 heatwave, which hit Continental Europe from May to October. In particular, we have examined Southern Italy, where Mediterranean forests suffer from climate change. We have computed the index's time series and show that it can be used to indicate the atmospheric background conditions associated with meteorological drought. We have also found a good agreement with soil moisture, which suggests that the persistence of anomalously high water deficit index was an essential driver of the rapid development and evolution of the exceptionally severe 2017 droughts.

Multi-board electronic cases with high density and high power modules are widely used in industrial power supply management. With the improvement of case performance and miniaturization requirements, heat dissipation becomes one of the important factors to be considered in the design process. First,The existing small electronic thermal design methods focus on heat dissipation structure or heat source layout optimization,and ignores on-load test for modeling analysis. Second,The selected power module has on-load power consumption, resulting in relatively low calorific value and the effectiveness of thermal design cannot be verified. Third, The thermal lacks Intelligent monitoring and feedback control mechanism. In order to solve these problems, this paper designs a kind of heat dissipation case with intelligent temperature control based on high-power and high-density power supply array. Based on the extremely miniaturization design principle, we adopt the composite heat dissipation mode based on conduction and supplemented by forced air cooling . The case is made of magnesium and aluminum alloy with a perforated design. Finally, we compare and analyze with the existing cooling design. The results show that the case is smaller in volume, and the cooling performance parameters are slightly better than the existing case. Under the condition of high-density and high-power design, The output power of the whole system is not less than 10kw and the lowest packing-level density is not less than 47w/cm2 with high reliability, portability and practicability. It also provides technical support and prototype support for the standardized design of similar power arrays.

By taking advantage of a stability criterion established recently, the critical temperature T_c is reckoned with help of the microscopic parameters, characterising the normal and superconducting electrons, namely the independent-electron band structure and a repulsive two-electron force. The emphasis is laid on the sharp T_c dependence upon electron concentration and inter-electron coupling, which might offer a practical route toward higher T_c values and help to understand why high-T_c compounds exhibit such remarkable properties.

There is increasing evidence that rising temperatures and heatwaves in the United Kingdom are associated with an increase in heat-related mortality. This study aims to retrospectively quantify the impact of heatwaves on mortality during the 2019 summer period using daily death occurrences. Second, it compares excess mortality during the 2019 heatwaves to excess mortality during the 2018 and 2017 heatwave periods. Lastly, it compares the excess mortality in the 2017-2019 heatwaves to the estimated excess deaths for the same period in the Public Health England (PHE) Heatwave mortality monitoring Reports. The cumulative number of excess deaths during the summer 2019 heatwaves were minimal and were substantially lower than during the summer 2018 heatwaves (1,700 deaths) and summer 2017 heatwaves (1,489 deaths). All findings were at variance with the PHE Heatwave mortality monitoring reports which estimated cumulative excess deaths to be 892, 863 and 778 during the summer period of 2019, 2018 and 2017 respectively using provisional death registrations. Issues have been identified in the use of provisional death registrations for mortality monitoring and the reduced reliability of the ONS daily death occurrence database before 2019. These findings may identify more reliable ways to monitor heat mortality during heatwaves in the future.

In this work, we propose a method to measure planar temperature fields of fluids flow. We used a focusing schlieren technique together with a calibration procedure to fulfill such purpose. The focusing schlieren technique uses an off-axis circular illumination to reduce the depth of focus of the optical system. The calibration procedure is based on the relation of the intensity level of each pixel of a focused schlieren image to the corresponding cutoff grid position measured at the exit focal plane of the schlieren lens. The method is applied to measure planar temperature fields of the hot air issuing from a 10 mm diameter nozzle of a commercial Hot Air Gun Soldering Station Welding. Our tests are carried out at different temperature values and different planes along the radial position of the nozzle of the Hot Air Gun Soldering Station Welding. The temperature values obtained experimentally are in agreed with those obtained with a thermocouple.

The aim of the study was to evaluate the influence of transduser design and its elements, and their materials on temperature in deeper layers of tissues measurement results. A digital modeling was performed to evaluate the influence of the properties of transduser design elements. Experimental research was carried out. Revealed that the accuracy, similar to that of an invasive method using needle probes, can be achieved by measuring the temperature in deeper muscle layers using the proposed transducer.

There is a perception among the inhabitants of the Aburrá Valley Region, that this heavily populated region, situated in the Andean mountains of Colombia, has been suffering large temperature elevations in the last years, especially in the last decade. To give perspective about this issue, the authors have gone through the available information about temperature changes in three meteorological stations in the region and have correlated it with a set of variables of urban, climatic and energetic nature, with the intention of developing an approximate model to understand the temperature changes. Changes in the mean temperature, based on the linear correlation of the data were estimated on 0.47oC for the 20 years between 1995 and 2015; the study showed that 60% of change was found to be related to local human activities and 40% was attributed to the impact of global warming. For the local influences some practical mitigation actions are proposed, related to improve the energy management and paying more attention to the temperature changes trough improvements in the number and capability of sampling stations in the urban air and in the river, which serve as clear indicators of the changes and the effect of any mitigation measures.

There is a perception among the inhabitants of the Aburrá Valley Region, that this heavily populated region, situated in the Andean mountains of Colombia, has been suffering large temperature raises in the last years, especially in the last decade. To give perspective about this issue, the authors have gone through the available information about temperature changes in three meteorological stations in the region and have correlated it with a set of variables of urban, climatic and energetic nature, with the intention of developing an approximate model to understand the temperature changes. Changes in the mean temperature, based on the linear tendencies, were estimated on 0.47ºC for the 20 years between 1995 and 2015; 60% of change was found to be related to local human activities and 40% was attributed to the impact of global warming.