The present study utilizes a metal inert gas welding (MIG) to make a dissimilar weld joint of different stainless steel grades AISI 304, 314, 316L, 420 and a standard structural steel S355MC to estimate the correlation of a microstructure and the mechanical properties. The microstructure of the base metals (BM), the heat affected zone (HAZ), the fusion zone (FZ) and the weld seam were analyzed using optical microscopy. Optical microscopy did not reveal any presence of weld defects such as porosity or cracks. The analysis of microstructure showed that both the austenitic and martensitic stainless steel weld structures contain some retained delta ferrite and coarse Me23C6 carbides in the HAZ, while the FZ exhibits delta ferrite and some retained austenite. The hardness profiles revealed difference between austenitic and martensitic steel welds that the later showed extremely high values in the HAZ (~500 HV/0.1) which causes fracture in this zone. The welds of all austenitic steel grades withstood tensile test, showing the average tensile strength of 472 MPa with fracture observed in the base metal zone. It made clear that the use of a filler rod 308LSI is suitable only for the austenitic stainless and structural steel dissimilar welds, and not appropriate for martensitic-structural steel welds. The achieved results revealed that the higher hardness of the martensitic phase in the HAZ of AISI 420 is closely related with the formation of untempered coarse martensitic structure and higher carbon content.

The screening and treatment of acid mine drainage (AMD) using Na₂FeO₄ has been explored. Elemental composition was performed using an ICP-OES for the raw and treated AMD. The AMD samples were collected from three different sampling sites (RTW1, RTW2 and RTW3) in Pretoria, South Africa with acidic pH ranging between 2.50 and 3.13. Total dissolved solids and Electrical Conductivity of AMD samples ranged between 960 and > 1000 mg. L^-1, 226 and 263 µS. cm^-1, respectively. The final pH of treated water samples increased up to ≥ 9.5 after treatment with Na₂FeO₄. Sodium ferrate showed dual functions by removing metals and raising the pH of the treated water. Concentrations of most trace elements were not complying with WHO and DWAF guideline standards in raw AMD while after treatment with Na₂FeO₄ the concentrations were below guidelines for domestic and irrigation purposes.

A series of polycaprolactones (PCLs) with molecular weights of 950–10,100 g mol−1 and Ð of 1.10–1.87 have been synthesized via one-pot, solvent-free ring-opening polymerization (ROP) of ε-caprolactone (CL) using a heterogeneous double metal cyanide (DMC) catalyst. Various initiators such as polypropylene glycol, ethylene glycol, propylene glycol, glycerol, and sorbitol are employed to tune the number of hydroxyl end groups and properties of the resultant PCLs. Kinetic studies indicate that the DMC-catalyzed ROP of CL proceeds via a coordination mechanism. Branched PCLs copolymers are also synthesized via the DMC-catalyzed copolymerization of CL with glycidol. The α,ω-hydroxyl functionalized PCLs were successfully used as telechelic polymers to produce thermoplastic poly(ester-ester) and poly(ester-urethane) elastomers with well-balanced stress and strain properties.

Alzheimer’s disease (AD) is one of the most prevailing neurodegenerative diseases, characterized by memory dysfunction and the presence of hyperphosphorylated tau and amyloid β (Aβ) aggregate in multiple brain regions, including the hippocampus and cortex. The exact etiology of AD has not yet been confirmed. However, epidemiological reports suggest that populations who were exposed to environmental hazards are more likely to develop AD than those who were not. Arsenic (As) is a naturally occurring environmental risk factor abundant in the Earth’s crust and human exposure to As predominantly occurs through drinking water. Convincing evidence suggests that As causes neurotoxicity and impairs memory and cognition although the hypothesis and molecular mechanism of As-associated pathobiology in AD are not clear yet. However, exposure to As and its metabolites leads to various pathogenic events such as oxidative stress, inflammation, mitochondrial dysfunctions, ER stress, apoptosis, impaired protein homeostasis, and abnormal calcium signaling. Evidence has indicated that As exposure induces alterations that coincide with most of the biochemical, pathological, and clinical developments of AD. Here, we overview existing literature to gain insights into the plausible mechanisms that underlie As-induced neurotoxicity and the subsequent neurological deficits in AD. Prospective strategies for the prevention and management of arsenic exposure and neurotoxicity have also been discussed.

Aiming the characterization of road dusts on the surrounding villages of an active mine and to assess metal(loids) bioaccessible fractions, a dust samples survey was undertaken. To achieve these objectives, pseudototal element concentration, mineralogical composition, Enrichment factor and in vitro extraction UBM assay for both gastric (G) and gastrointestinal (GI) phases, were determined. Results obtained revealed that arsenic represents the higher risk to humans, with mean pseudototal values higher than the maximum reference value range. Enrichment factor points to As significant to very high enrichment in all villages. Particles enriched in As, Ca, Fe, Cu, Al, Ti were identified by SEM-EDS in weathered agglomerates, linked to mine wastes and long-distance transport, both by wind and/or traffic. Arsenic bioaccessibility fraction (%BAF) presents low values in the studied samples, possibly due to low Fe complexes solubility with adsorbed As, limiting arsenic release and reducing its bioaccessibility. Concentrations of Cd bioaccessible G and GI phases are within the reference values range, while for Cu are above and for Pb are lower, than reference value range. Results show that the pseudototal fraction risk is overestimated when comparing to BAF (bioaccessible fraction), nevertheless, total G and GI risk are above the carcinogenic target risk (1.00E-06) in most samples. Carcinogenic risk of the bioaccessible contaminants shows that As is the element that represents higher risk for developing cancer over a lifetime, being ingestion the main risk route.

: Dacarbazine, DAC, 5-(3,3-dimethyltriazeno)imidazol-4-carboxamideis is an imidazole-carboxamide derivative, that is structurally related to purines. DAC belongs to the triazene compounds, which are a group of alkylating agents with antitumour and mutagenic properties. DAC is a non-cell cycle specific drug, active on all phases of cellular cycle. In the frame of this work the 3d-metal complexes (cobalt and copper) with dacarbazine were synthesized. Their spectroscopic properties by the use of FT-IR, FT-Raman and 1HNMR were studied. The structures of dacarbazine and its complexes with copper(II) and cobalt(II) were calculated using DFT methods. The effect of metals on the electronic charge distribution of dacarbazine was discussed on the basis of calculated NBO atomic charges. The reactivity of metal complexes in relation to ligand alone was estimated on the basis of calculated energy of HOMO and LUMO orbitals. The aromaticity of imidazole ring in dacarbazine and the complexes was compared (on the basis of calculated geometric indices of aromaticity). Thermal stability of the investigated 3d-metal complexes with dacarbazine and the products of their thermal decomposition were analyzed.

The paramagnetic gadolinium(III) ion is used as contrast agent in magnetic resonance (MR) imaging to improve the lesion detection and characterization. It generates a signal by changing the relaxivity of protons from associated water molecules and creates a clearer physical distinction between the molecule and the surrounding tissues. New gadolinium-based contrast agents displaying larger relaxivity values and specifically targeted might provide higher resolution and better functional images. We have synthesized the gadolinium(III) complex of formula [Gd(thy)2(H2O)6](ClO4)3·2H2O (1) [thy = 5-methyl-1H-pyrimidine-2,4-dione or thymine], which is the first reported compound based on gadolinium and thymine nucleobase. 1 has been characterized through vis-IR, SEM-EDAX and single-crystal X-ray diffraction techniques, and its magnetic and relaxometric properties have been investigated by means of SQUID magnetometer and MR imaging phantom studies, respectively. On the basis of its high relaxivity values, this gadolinium(III) complex can be considered a suitable candidate for contrast enhanced magnetic resonance imaging.

Bacteria a Microscopic organisms are the most inexhaustible and flexible of microorganisms and constitute a huge division of the whole living earthly biomass, certain microorganisms were found to amass metallic components at a high limit Was Known as Bacterial Bio-sorption Due to their little size, capacity to become under controlled conditions, and their Accommodation to an extensive variety of ecological situations; Potent metal bio-sorbents among microorganisms, at low pH esteems, cell divider ligands are protonated and contend essentially with metals for official. With expanding pH, more ligands, such as amino and carboxyl groups, could be exposed, leading to attraction between these negative charges and the metals, and consequently increment bio-sorption onto the cell surface. Starting with Isolation and identification of heavy metal-resistant bacteria from rock Ore. Studying Factors Affecting Uranium Bio-sorption, Optimization of bacterial growth conditions and optimum for metal uptake by free and immobilized bacterial cells and Desorption ratio of uranium ions adsorbed by Coli. /alginate, All this evidence suggest that functions groups Represented in our study are responsible for metal uptake in our bacterial biomass beside change in peaks position which assigned for it's groups confirm bio-sorption of metal ions from waste due to ions charge interaction comparing with immobilized we found increase in no of binding sites indicate that immobilized bacterial have high efficiency for metal up take which also change in peaks position which assigned for its groups confirm bio-sorption of metal ions from waste due to ions charge interaction, Where the high bio-sorption yield obtained by bacteria, the Uranium & heavy metal bioremediation process expects microorganisms to be joined to a strong surface.

In this article, it is proposed to use aluminum breakage scraps to obtain Green Hydrogen through the aluminum-water reaction with caustic soda as a catalyst. From this exothermic reaction, both hydrogen and the heat generated can be used. Due to the low price of aluminum chips, this allows us to produce Green hydrogen below the current price that is obtained using renewable energy sources and electrolyzers. On the other hand, we have developed a process that is sustainable since it is obtained as alumina and caustic soda waste that can be reused. This alumina obtained, once filtered, has high purity which allows us to produce high-quality primary aluminum without the need to use bauxite and reducing the production of red sludge. A comparative study-analysis has been carried out of two of the types of forms in which the most common aluminum is presented in the industry to analyze which one performs better by studying key factors such as the hydrogen produced, and the waste generated during the process. Finally, the mathematical model has been defined to be able to control the flow based on different key parameters such as temperature, molarity, and geometry. Undoubtedly, the study that we present represents a milestone for the recovery of metallic aluminum waste and may be of great interest to industries that use aluminum in their processes, such as recuperators, but also the vehicle or aerospace industry.

Hybrid metal-organic compounds as relatively new and prosperous magnetoelectric multiferroics provide opportunities to improve the polarization, magnetization and magneto-electric coupling at the same time, which usually have some limitations in the common type-I and type-II multiferroics. In this work we investigate the crystal of guanidinium copper(II) formate [C(NH2)3]Cu(HCOO)3 and give novel insights concerning the structure, magnetic, electric and magneto-electric behaviour of this interesting material. Detailed analysis of crystal structure at 100 K is given. Magnetization points to the copper(II)-formate spin-chain phase that becomes ordered below 4.6 K into the canted antiferromagnetic (AFM) state, as a result of super-exchange interaction over different formate bridges. The performed ab-initio colinear density functional theory (DFT) calculation confirm the AFM-like ground state as a first approximation and explain the coupling of spin-chains into the AFM ordered lattice. In versatile measurements of magnetization of a crystal, including transverse component besides the longitudinal one, very large anisotropy is found that might originate from canting of the coordination octahedra around copper(II) in cooperation with the canted AFM order. With cooling down in zero fields the generation of spontaneous polarization is observed step-wise below 270 K and 210 K and the effect of magnetic field on its value is observed also in the paramagnetic phase. Measured polarization is somewhat smaller than the DFT value in the c-direction, possibly due to twin domains present in the crystal. The considerable magneto-electric coupling below the magnetic transition temperature is measured with different orientations of the crystal in magnetic field, giving altogether the new light onto the magneto-electric effect in this material.

In recent years, the class of metal-organic framework (MOF) materials emerged. These materials' unique properties can be assigned to their structure, containing inorganic nodes connected with organic linkers. Due to their porosity and flexibility, MOFs have become suitable for various energy-related applications, including gas storage, hydrogen production and heterogeneous catalysis, and photocatalysis. Using DFT+U calculations, we show that the substitution of metal centers in inorganic nodes and the strain engineering of UiO-66 alters the electronic and optical properties of this material. We show that applying mechanical strain on UiO-66 enables the control of absorption coefficient in the UV-Vis spectrum and the photocatalytic processes' selectivity when reactants for several photocatalytic processes are present. The presented findings could lead to general strategies for designing novel MOFs for sustainable energy conversion applications.

Both types of surgical guides – with and without metal sleeves are founded beneficial in clinical studies. The aim of this in vitro study was to compare time of surgical procedure in dental implantology depending of used type of the surgical guide. Ten three dimensional (3D) printed models of lower jaws were prepared based on complete virtual model of patient clinical conditions with missing teeth 37, 46 and 47. Five of this models were used for implant sites preparation performed with use of surgical guide without metal sleeves and dedicated surgical kit, and next five were used for the same procedure performed with surgical guide with metal sleeves and dedicated surgical kit. Time of implant site preparation were measured and noted. Statistical analysis was performed using Student’s t test for independent samples. Difference of time in both groups were founded as statistically significant (t=-9.94; df =28; p=0.0000). Type of surgical guide is important factor which can impact on time of implant site preparation and all surgical procedure.

Sorghum is a multipurpose crop, but Cr(VI) toxicity influenced the production of the crop and have established highlighted courtesy, due to robust toxicity and a comparatively less known mode of action. Many reports approve the negative impact of Cr(VI) on plants. Yet, it is not clear that, at what concentrations, Cr(VI) inhibits the growth and nutrient quality of Sorghum. In the present research, toxic effects appeared after 1ppm of Cr treatment. The plant growth decreased 15 – 20% and nutritional quality decreased 30 – 40% significantly with increasing concentration of Cr(VI). Toxic components increased 14 – 16% with increasing concentration of Cr(VI) in both the varieties (HJ 541 and SSG 59-3). Chromium was accumulated more in roots followed by shoots with increasing Cr(VI) treatments (0-4 ppm). Chromium at 4ppm level was becoming lethal to Sorghum. Sorghum cultivar SSG 59-3 was more tolerable to Cr toxicity than HJ 541. Chromium accumulated in Sorghum and increased HCN content and at higher doses adversely affects the nutritive values and growth making it toxic for animal consumption. These findings may be useful for scheming a mitigation strategy for chromium toxicity.

: TiAl6V4 alloy is widely used in selective laser melting and direct laser melting. In turn, works devoted to the issue of how the track stacking scheme affects the value of mechanical properties is not enough. The influence of the Ti6Al4V alloy track trajectories on the microstructure and mechanical properties during direct laser deposition is studied in this article for the first time. The results were obtained on the influence of «parallel» and «perpendicular» technique of laying tracks in direct laser synthesis. All studied samples have a microstructure typical of the hardened two-phase condition titanium. It is shown that the method of laying tracks and the direction of load application during compression testing relative to the location of the tracks leads to a change in the ultimate strength of the Ti-6Al-4V alloy from 1794 to 1910 MPa. The plasticity of the Ti-6Al-4V alloy obtained by direct laser alloying can vary from 21.3 to 33.0% depending on the direction of laying the tracks and the direction of the compression test. The hardness of alloys varies in the range from 409 to 511 HV and depends on the method of laying the tracks and the direction of hardness measurements.

Metal 3D printing technology is a promising manufacturing method. The quality of the printed product can pass for mechanical application, if the anisotropy of the microstructure, imperfections, deformation, and residual stress of the printed sample could be lower than the appropriate level or if they are fully illuminated. Thermal stress is one of the significant reasons for deformation in the 3D printed samples. Thermal stresses are the direct consequence of the local temperature gradient. In this research, the effect of the temperature printer’s chamber (from room temperature to 900 C) was studied on thermal stress and subsequent total deformation in the printed sample. The printed sample is a six-layers-printed walk, which could be considered as a building block of other complex shapes and give us inside about deformation. The computational results show a meaningful reduction in thermal stress and deformation at the higher temperature of the printer’s chamber. The lower final deformation of the printed sample is an important subject, especially for samples with complex shapes.

Understanding potential uptake and biodistribution of engineered nanoparticles in soil-grown plants is imperative for toxicity and risk assessment considering the oral exposure of edibles by humans. Herein, we assessed potential influence of particle size (25, 50, and 250 nm) and concentration (0, 50, 100, 200, and 500 mg/kg-soil) of Copper oxide nanoparticles (CuONPs) on: (1) the root system architecture, and the physicochemical attributes of soil at the soil-root interface, (2) leading to Cu transport and accumulation in root, stem, leaf and seed in soybean (Glycine max cv Kowsar) grown for entire lifecycle of 120 days, and compared with soluble Cu²⁺ ions and water-only controls, and (3) performed a comparative assessment of total seed Cu levels in soybean with other valuable food sources for Cu intake and discussed its human health implications. Our findings showed particle size- and concentration-dependent influence of CuONPs on Cu uptake and tissue distribution in root, stem, leaf and seed in soybean. Alterations in root architecture (root dry weight, root length, root volume, and root area) were dependent on the Cu compound type, Cu concentrations, and their interactions (p<0.05), except for root density. Concentration-response relationships for all three sized CuONPs, and Cu²⁺ ions, were linear. CuONPs and Cu²⁺ ions had inhibitory effects on root growth and development. Overall, soybean responses to smallest size CuONPs-25 nm were higher for all parameters investigated compared to two larger sized CuONPs (50 nm, 250 nm) or Cu²⁺ ions. Cu uptake/bioaccumulation differed among soybean tissues in the order: root > leaf > stem > seed. Despite reduced root architecture and seed yield, our smallest size CuONPs-25 nm led to increased total seed Cu uptake compared to the larger sized CuONPs and Cu²⁺ ions tested. Our findings also suggest that soil amendment by CuONPs, more so by the smallest size CuONPs-25 nm, could significantly improve nutritional Cu value in soybean seed as reflected by % Daily Values (DV), and are rated “Good” to “Very Good” according to the “World’s Healthiest Foods” rating. However, until the potential toxicity and risk from consumption of soybean seed is characterized in humans, caution should be exercised when the Cu fortified seeds are used for daily human consumption when addressing Cu deficiency and associated illnesses, globally.

In this paper, a metal cutting machine position control have been designed and simulated using Matlab/Simulink Toolbox successfully. The open loop response of the system analysis shows that the system needs performance improvement. Static output feedback and full state feedback H₂ controllers have been used to increase the performance of the system. Comparison of the metal cutting machine position using static output feedback and full state feedback H₂ controllers have been done to track a set point position using step and sine wave input signals and a promising results have been analyzed.

Highly sensitive multicomponent materials designed for the recognition of hazardous compounds request control over interfacial chemistry. The latter is key parameter in the construction of the sensing (macro)molecular architectures. In this work, multi-walled carbon nanotubes (in short, CNTs) were deposited on diazonium-modified flexible ITO electrodes prior to electropolymerization of pyrrole. This three step process, including diazonium electroreduction, deposition of CNTs and electropolymerization, provided adhesively bonded polypyrrole-wrapped CNT composite coatings on aminophenyl-modified flexible ITO sheets. The aminophenyl (AP) groups were attached to ITO by electroreduction of the in situ generated aminobenzenediazonium compound in aqueous, acidic medium. For the first time, polypyrrole (PPy) was electrodeposited in the presence of both benzenesulfonic acid (dopant) and ethylene glycol-bis(2-aminoethylether)-tetraacetic acid (EGTA) which acts as a chelator. The flexible electrodes were characterized by XPS, Raman and scanning electron microscopy (SEM) which provided strong supporting evidence for the wrapping of CNTs by the electrodeposited PPy. Indeed, the CNT average diameter increased from 182.6 nm to 274.8, 35.65.9 and 17520.1 after 1, 5 and 10 of electropolymerization of pyrrole. The PPy/CNT/NH2-ITO films generated by this strategy exhibit significantly improved stability and higher conductivity compared to a similar PPy coating without any embedded CNTs as assessed by from electrochemical impedance spectroscopy measurements. The potentiometric response was linear in the 10-83×10-7 mol.L-1 Pb(II) concentration range and the detection limit was 2.9×10-9 mol.L-1 at S/N=3. The EGTA was found to drastically improve selectivity for Pb(II) over Cu(II). To account for this improvement, density functional theory (DFT) was employed to calculate the EGTA-metal ion interaction energy which was found to be -374.6 and -116.4 kJ/mol for Pb(II) and Cu(II), respectively, considering solvation effects. This work demonstrates the power of a subtle combination of diazonium coupling agent, CNTs, chelators and conductive polymers to design high-performance electrochemical sensors for environmental applications.

The development of sensors for monitoring Carbon Monoxide (CO) in a large range of temperature is of crucial importance in areas as monitoring of industrial processes or personal tracking using smart objects. Devices integrating GaN/Ga₂O₃ core/shell nanowires (NWs) is a promising solution allowing combining the high sensitivity of the electronic properties to the states of GaN-core surface; and the high sensitivity to CO of Ga₂O₃-shell. Because the performances of sensors primarily depend on the material properties composing the active layer of the device, it is essential to control these properties and in first time its synthesis. In this work, we investigate the synthesis of GaN/Ga₂O₃ core-shell NWs with a special focus on the formation of the shell. The GaN NWs grown by Plasma-assisted molecular beam epitaxy, are post-treated following thermal oxidation to form Ga₂O₃-shell surrounding the GaN-core. We establish that the Ga₂O₃-shell thickness can be modulated from 1 up to 14 nm by changing the oxidation conditions, and follows the diffuse-controlled reaction. By combining XRD-STEM and EDX analysis, we also demonstrate that the oxide shell formed by thermal oxidation is crystalline and presents the β-Ga₂O₃ crystalline phase, and is synthesized in epitaxial relationship with the GaN-core.

Food preservatives are compound that are used for the treatment of food to improve the shelf life. In the food industry, is necessary to monitor all processes, for both safety and quality of the product. An electronic nose (or e-nose) is a biomimetic olfactory system that could find numerous industrial applications, including food quality control. Commercial electronic noses are based on sensor arrays composed by a combination of different sensors, which include conductometric metal oxide devices. Metal oxide nanowires are considered among the most promising materials for the fabrication of novel sensing devices, which can enhance the overall performances of e-noses in food applications. In the present work, is reported the fabrication of a novel sensor array based on SnO2, CuO and WO₃ nanowires deposited on top of commercial μHPs, provided by ams Sensor Solutions Germany GmbH. The array was tested for the discrimination of four typical compounds added to food products or used for their treatment to increase the shelf life: ethanol, acetone, nitrogen dioxide and ozone. Results are very promising: the sensors array was able to operate for long time consuming less than 50mW for each single sensor, and PCA analysis confirms that the device was able to discriminate between different compounds.

Light sources tend to affect images captured in any automatic optical inspection (AOI) system. In this study, the effectiveness of metal-halide lamps, quartz-halogen lamps, and LEDs as the light sources in AOI systems for the detection of the 3rd and 4th layers electrodes of thin-film-transistor liquid crystal displays (TFT-LCDs) is examined experimentally. The results show that the performance of LEDs is generally comparable or better than that of metal-halide and quartz-halogen lamps. The best optical performance is by the blue LED due to its spectrum compatibility with the time-delay-integration charged-coupled device (TDI CCD) sensor and its better spatial resolution. The images revealed by the blue LED are sharper and more distinctive. Since current LEDs are more energy efficient and environmentally friendly, using LEDs as the light source for AOI is very beneficial. As the blue LED performs the best, it should be adopted for AOI using TDI CCD sensors.

The apparent metal-insulator transition (MIT) in two-dimension (2D) was discovered by Kravchenko et al. [1] more than two decades ago in strongly interacting 2D electrons residing in a Si-metal-oxide-semiconductor field-effect transistor (Si-MOSFET). Its origin remains unresolved. Recently, low magnetic field reentrant insulating phases (RIPs), which dwell between the zero-field (B=0) metallic state and the integer quantum Hall (QH) states where the Landau-level filling factor υ > 1, have been observed in strongly correlated 2D GaAs hole systems with large interaction parameter rs (~20-40) and high purity. A new complex phase diagram was proposed, which includes zero field MIT, low magnetic field RIPs, integer QH states, fractional QH states, high field RIPs and insulating phases (HFIPs) with υ < 1 in which the insulating phases are explained by the formation of Wigner crystal. Furthermore, evidences of new intermediate phases were reported. All contribute to the further understandings of the puzzle. This review article serves the purpose of summarizing those recent experimental findings and theoretical endeavors, to foster future research efforts.

Metal-Organic Frameworks (MOFs) are a subclass of porous materials that have unique properties such as varieties of structures from different metals and organic linkers, tunable porosity from a structure or framework design, etc. Moreover, modification/functionalization of the material structure could optimize the material properties and demonstrate high potential for a selected application. MOF materials exhibit exceptional properties and make these materials widely applicable including in energy storage and heat transformation applications. This review aims to give a broad overview of MOFs and their development as adsorbent materials having the potential for heat transformation applications. We summarize current investigations, developments, and possibilities of metal-organic frameworks (MOFs) especially the tuning of the porosity and hydrophobic/hydrophilic design required for this specific application. These materials applied as adsorbent are promising in the thermal driven adsorption for heat transformation using water as working fluid and related application.

To remove sulfur-containing compounds (SCC) from the diesel fraction 200-360 °C extraction systems have been created based on coordinating organic solvents - dimethylformamide and dimethylsulfoxide and chlorides (CoCl2, CuCl2, CdCl2, MnCl2 and CrCl3) and metal trifluoroacetates (Co (TFA)2, Cu(TFA)2 and Mn(TFA)2). Using PMR spectroscopy the coordination of chloride and metal trifluoroacetate on the oxygen atom in the carbonyl group of DMFA was shown to redistribute electron density in the solvent molecule and to enhance properties of the acceptor center localized on the nitrogen atom. The removal of sulfur-containing compounds from the diesel fraction proceeded under mild conditions - at the temperature of 25 °C and atmospheric pressure. The degree of SCC removal from the diesel fraction in 30 minutes extraction was more than 90%. The interaction of organic solvents with metal salts and sulfur-containing compounds of the diesel fraction was considered within the framework of the concept of "hard and soft acids and bases" (HSAB). The most complete SCC extraction was carried out by "DMFA - Mn(TFA)2, MnCl2 and CrCl3 systems, that was probably connected with the implementation of the" hard base - hard acid "system.

Slow and controlled release systems for drugs, have attracted increasing interest recently. A highly efficient metal-organic gels (MOGs) drug delivery carrier, i.e., MIL-100(Al) gels, has been fabricated by a facile, low cost and environment friendly one-pot process. The unique structure of MIL-100(Al) gels leads to a high loading efficiency (620 mg/g) towards doxorubicin hydrochloride (DOX) as a kind of anticancer drugs. DOX-loaded MOGs exhibited high stability under physiological conditions and sustained release capacity of DOX for up to 3 days (under acidic environments). They further showed sustained drug release behavior and excellent antitumor effects in in vitro experiments on HeLa cells, in contrast with the extremely low biotoxicity of MOGs. Our work provides a promising way for the anticancer therapy, by utilizing this MOGs-based drug delivery system, as an efficient and safe vehicle.

Soy protein isolate (SPI) based materials are abundant, biocompatible, renewable, and biodegradable. In order to improve the tensile strength (TS) of SPI films, we prepared a novel composite film modified with microcrystalline cellulose (MCC) and metal nanoclusters (NCs) in this research. The effects of the modification of MCC on the properties of SPI-Cu NCs and Zn NCs films were investigated. Attenuated total reflectance-Fourier transformed infrared spectroscopy analyses and X-ray diffraction patterns characterized the strong interactions and reduction of the crystalline structure of the composite films. Scanning electron microscope showed the enhanced cross-linked and entangled structure of modified films. Compared with untreated SPI film, the tensile strength of the SPI-MCC-Cu and SPI-MCC-Zn films increased from 2.91 MPa to 13.95 and 6.52 MPa, respectively. Moreover, the results also indicated their favorable water resistance with higher water contact angle. Meanwhile, the composite films exhibited increased initial degradation temperatures, demonstrating their higher thermostability. The results suggested that MCC could effectively improve the performance of SPI-NCs films, which would provide a novel preparation method for environmentally friendly SPI-based films in the applications of packaging materials.

1) Background: Bipolar or manic-depressive disorder is a malign mental disease that frequently faces social stigma. Educational and thinking models are needed to increase people’s awareness and understanding of the disorder. The arts have potential to achieve this goal. 2) Methods: This paper builds on the recent use of heavy metal music as a thinking and education model. It emphasizes the artistic component of heavy metal and its potential to characterize the symptomatology during the episodes of (hypo)mania and depression and the recurrence of these episodes. Heavy metal music has diversified into subgenres that become allegorical to both the symptoms of episodes and the recurrence of bipolar cycles. 3) Results: Examples of songs are given that mirror distinct facets of the disorder. 4) Conclusion: Although the links drawn between art (music) and science (psychiatry) are inherently subjective, such connections might be used to trigger a learning process, facilitate judgment and decision-making, and induce affective reactions and memory formation in the listener. The approach may facilitate collaborative efforts and serve healthcare professionals and educators as a communication tool to aid the public’s comprehension of the disease and an associated social paradox: On one hand, bipolar disorder incurs substantial costs to society. On the other hand, it benefits from the creative artistic and scientific endeavors of bipolar individuals from which cultural and political gains may ensue.

The nature of multi-energy systems requires the integration of interdisciplinary methodologies and complementary tools in a coherent and systematic manner. Therefore, it is imperative to develop an efficient experimental environment to effectively implement the interaction between different tools for structural and parametric optimization (synthesis) of multi-energy systems and analysis of their operation. Due to the inherent complexity of the energy system optimization model, solving the synthesis problem often leads to significant challenges in terms of required computational resources and runtime. Known synthesis approaches do not fully address these challenges. In this context, we propose a subject-oriented environment for the multi-energy system synthesis in a reasonable time considering the available computational resources. The basis of the environment is a service-oriented application. The modeling and optimization of the studied systems is performed by means of scientific workflows. The execution of the specialized tools for modeling and optimization is done through web services. The pre-selection of these tools, depending on the level of model detail of the systems under study, and the data validation are performed on the specially developed testbeds. Such testbeds are constructed as system workflows. This is one of the distinguishing features of our approach. The application of the proposed environment is demonstrated through a case study on the synthesis of a microgrid (a special case of a multi-energy system). As a result of the study, an optimal microgrid configuration was proposed. It is based on the cogeneration of heat and electricity generation using natural gas.

With the large-scale application of Internet of Things (IoT) in the medical field, eHealthcare has attracted wide attention. With the help of IoT devices, eHealthcare allows doctors to monitor patients’ health conditions and make recommendations accordingly. The addition of cloud computing greatly saves Healthcare Center’s (HC) computing resources. In order to provide privacy and fine-grained access control, Attribute-b ased encryption (ABE) is widely favored. HC usually operates multiple medical institutions in different regions, and each medical institution can be regarded as a attribute authority. Therefor, multi-authority (MA) ABE is usually concerned to encrypt the patient data. However for existing MA-ABE algorithms, the ciphertext is long and the efficiency of encryption and decryption is low. These problems will greatly increase the computing burden of patients and seriously affect the efficiency of data transmission. Hence we propose a decentralized key-policy MA-ABE in eHealthcare. The proposed algorithm can achieve decentralization, that is, it does not need central authority. Meanwhile, compared with existing MA-ABE algorithms, the length of ciphertext generated by our algorithm is shorter, and the efficiency of encryption and decryption is significantly improved. With the help of Java Pairing Based Cryptography, we carried out the experiments which show that our algorithm can effectively reduce the time required for encryption and decryption.

In this paper, we present a multi-task model that predicts disparities and confidence levels in deep stereo matching simultaneously. We do this by combining its successful model for each separate task and obtaining a multitask model that can be trained with a proposed loss function. We show the advantages of this model compared to training and predicting disparity and confidence sequentially. This method enables an improvement of 15% to 30% in the area under the curve (AUC) metric when trained parallel rather than sequential. In addition, the effect of weighting the components in the loss function on the stereo and confidence performance is investigated. By improving the confidence estimate, the practicality of stereo estimators for creating distance images is increased.

Device to Device (D2D) is a pivotal technology in the next generation of communication, allowing for direct task offloading between mobile devices (MDs) to improve the efficient utilization of idle resources. This paper proposes a novel algorithm for dynamic task offloading between active MDs and idle MDs in the D2D-MEC (Mobile Edge Computing) system by deploying multi-agent deep reinforcement learning (DRL) to minimize the long-term average delay of delay-sensitive tasks under deadline constraints. Our core innovation is a dynamic partitioning scheme for idle and active devices in the D2D-MEC system, accounting for stochastic task arrivals and multi-time-slot task execution, which has been insufficiently addressed in existing literature. We adopt a queue-based system to formulate a dynamic task offloading optimization problem. To address the challenges of large action space and coupling of actions across time slots, we model the problem as a Markov Decision Process (MDP) and perform the multi-agent DRL through Multi-Agent Proximal Policy Optimization (MAPPO). We employ a centralized training with decentralized execution (CTDE) framework to enable each MD to make offloading decisions solely based on its local system state. Extensive simulations demonstrate the efficiency and fast convergence of our algorithm. In comparison with the existing sub-optimal results deploying single-agent DRL, our algorithm reduces the average task completion delay by 11.0% and the ratio of dropped tasks by 17.0%.

Background: The pathophysiology of functional dyspepsia (FD) remains insufficiently understood, and the pain and economic constraints associated with endoscopic examinations hinder the precise definition and treatment of this disorder. Exploring the potential of multi-omics biomarkers for FD could yield promising targets for effectively diagnosing and treating this condition. Methods: We recruited 54 FD patients and 29 healthy volunteers and characterized their gut microbiota by shotgun metagenomic sequencing and their serum and urine metabolites by liquid chromatography-mass spectrometry (LC-MS). Results: We identified the changes in circulating metabolites associated with FD and linked to the gut microbial alterations. Among the differential circulating metabolites, we particularly highlighted the strong association of L-glutamate deficiency with the severity of FD symptoms and its strong predictive value for FD. Although no significant changes were noted in the gut microbial community structure of the FD samples, this might be attributed to symptom overlap between epigastric pain syndrome (EPS) and postprandial distress syndrome (PDS). However, significant alterations in the abundance of certain species were observed, including a substantial increase in the abundance of Streptococcus in the digestive tract of patients with FD. Finally, a cross-omics correlation network integrating metabolomic data with microbial community abundance was established, uncovering potential host-microbe-metabolite interactions. Conclusions: This work provides the first comprehensive description of the disrupted state of blood and urine metabolite composition and gut microbiota in patients with FD. These findings potentially offer promising targets for the diagnosis and treatment of this condition through a multi-omics approach, with particular emphasis on serum metabolomics.

Reverse engineering is applied to identify optimum polymerization conditions for the synthesis of polymer with pre-defined properties. The proposed approach uses multi-objective optimization (MOO) and provides multiple candidate polymerization procedures to reach the targeted polymer property. The objectives for optimization include maximal similarity of molar mass distributions (MMD) compared to the target MMD, minimal reaction time, and maximal monomer conversion. The method is tested for vinyl acetate radical polymerizations and can be adopted to other monomers. The data for the optimization procedure is generated by an in-house developed kinetic Monte-Carlo (kMC) simulator for a selected recipe search space. The proposed reverse engineering algorithm comprises several steps: kMC simulations for the selected recipe search space to derive initial data, performing MOO for a targeted MMD, and identification of the Pareto optimal space. The last step uses a weighted sum optimization function to calculate the weighted score of each candidate polymerization conditions. To decrease the execution time clustering of the search space based on MMDs is applied. The performance of the proposed approach was tested for various target MMDs. The suggested MOO-based reverse engineering provides multiple recipe candidates depending on competing objectives.

Jujube (Ziziphus jujuba Mill.) stands as a pivotal fruit tree with significant economic, ecological, and social value. Recent years have witnessed remarkable strides in multi-omics-based biological re-search on jujube. This review began by summarizing advancements in jujube genomics. Subse-quently, we provided a comprehensive overview of the integrated application of genomics, tran-scriptomics, and metabolomics to explore pivotal genes governing jujube domestication traits, quality attributes (including sugar synthesis, terpenoids, and flavonoids), and responses to abiotic stress, and discussed the transcriptional regulatory mechanisms underlying these traits. Further-more, challenges in multi-omics research on jujube biological traits were outlined, and we pro-posed the integration of resources such as pan-genomics and sRNAome to unearth key molecules and regulatory networks influencing diverse biological traits. Incorporating these molecules into practical breeding strategies, including gene editing, transgenic approaches, and progressive breeding, holds the potential for achieving molecular-design breeding and efficient genetic en-hancement of jujube.

IP Multimedia Subsystem (IMS) supports high-speed transmission of multi-media like data, audio, and video between mobiles and other wireless devices. IMS is the most suitable for multimedia communication across multiple networks using the Internet of Things (IoT) and cloud computing. IoT-IMS can efficiently manage the huge amount of data generated by smart devices for audio-video during live streaming applications. During these services, the main problem is that an intruder can launch a Session Initialization Protocol (SIP) messages flooding attack on IMS that does not have the functionality to prevent itself from these types of attacks. In this paper, an intrusion detecting and preventing system (IDPS) is proposed that effectively detects the register flooding and spoofing attacks using SIP messages. We proposed a watermark embedding algorithm on the user side and an extraction algorithm on receiving side. A test-bed is set up for IMS where we have considered four different scenarios to evaluate the IDPS approach as compared to counterparts. Results illustrate the dominance of our scheme in terms of response time, register flooding attack detection ratios, CPU load utilization, fault detection ratio, and memory utilization. The fault detection ratio averagely 98.18

Background: Medulloblastoma (MB) comprises four broad molecular subgroups - wingless (WNT), sonic hedgehog (SHH), Group 3, and Group 4 respectively with subgroup-specific developmental origins, unique genetic profiles, distinct clinico-demographic characteristics, and diverse clinical outcomes. WNT-MB has the best outcomes (5-year survival >90%) with contemporary multi-modality treatment prompting attempts at treatment de-intensification to reduce late toxicity. This is a retrospective audit of clinical outcomes in WNT-MB patients treated at a tertiary-care comprehensive cancer centre. Methods: Patients with molecularly confirmed WNT-MB treated with maximal safe resection followed by post-operative standard-of-care risk-stratified adjuvant radio(chemo)therapy were identified retrospectively via electronic search of the neuro-oncology database. Data regarding clinico-demographic characteristics, histo-molecular features, treatment details, patterns of failure, and survival outcomes was retrieved from electronic medical records and/or hospital case files. Time-to-event outcomes were analyzed using Kaplan-Meier methods and compared with the log-rank test. Results: Between 2004 to 2020, 74 patients with WNT-MB were registered in the neuro-oncology unit of the institute. Seven patients treated on a prospective clinical trial of therapy de-intensification were excluded leaving 67 patients that constitute the present study cohort. Median age at presentation was 12 years (inter-quartile range 9-18 years) with a male preponderance (2:1). Six patients (1 post-operative mortality and 5 without adequate details of treatment or outcomes) were excluded from the survival analysis which was restricted to 61 patients. At a median follow-up of 72 months, Kaplan-Meier estimates of 5-year progression-free survival and overall survival were 87.7% and 91.2% respectively. Traditional high-risk features such as large residual tumor (≥1.5cm2) and leptomeningeal metastases (M+) did not significantly impact upon survival in this molecularly-characterized WNT-MB cohort. Conclusions: This retrospective clinical audit confirms excellent survival in WNT-MB patients treated with contemporary multi-modality therapy. Lack of prognostic impact of conventional high-risk features suggests the need for refined risk-stratification and potential de-intensification of therapy.

In this paper, we unite concepts from Husserlian phenomenology, the active inference framework in theoretical biology, and category theory in mathematics to develop a comprehensive framework for understanding social action premised on shared goals. We begin with an overview of Husserlian phenomenology, focusing on aspects of inner time consciousness, namely, retention, primal impression, and protention. We then review active inference as a formal approach to modeling agent behavior, based on variational (approximate Bayesian) inference. Expanding upon Husserl’s model of time consciousness, we consider collective goal-directed behavior, emphasizing shared protentions among agents and their connection to the shared generative models of active inference. This integrated framework aims to formalize shared goals in terms of shared protentions, and to thereby shed light on the emergence of group intentionality. Building on this foundation, we incorporate mathematical tools from category theory; particularly, sheaf and topos theory, to furnish a mathematical image of individual and group interactions within a stochastic environment. Specifically, we employ morphisms between polynomial representations of individual agent models, allowing predictions not only of their own behaviors but also those of other agents and environmental responses. Sheaf and topos theory facilitate the construction of coherent agent worldviews and provides a way of representing consensus or shared understanding. We explore the emergence of shared protentions, bridging the phenomenology of temporal structure, multi-agent active inference systems, and category theory. Shared protentions are highlighted as pivotal for coordination and achieving common objectives. We conclude by acknowledging the intricacies stemming from stochastic systems and uncertainties in realizing shared goals.

The fidelity of the decadal experiment in Coupled Model Intercomparison Project Phase-5 (CMIP5) has been examined, over different climate variables for different temporal and spatial scales, in many previous studies. However, most of the studies were for the temperature and temperature-based climate indices. A quite limited study was conducted on precipitation of decadal experiment and no attention was paid to a catchment level. This study evaluates the performances of eight GCMs (MIROC4h, EC-EARTH, MRI-CGCM3, MPI-ESM-MR, MPI-ESM-LR, MIROC5, CMCC-CM, and CanCM4) for the monthly hindcast precipitation of decadal experiment over the Brisbane River catchment in Queensland, Australia. First, the GCMs datasets were spatially interpolated onto a spatial resolution of 0.050×0.050 (5 km× 5 km) matching with the grids of observed data and then were cut for the catchment. Next, model outputs are evaluated for temporal skills, dry and wet periods, and total precipitation (over time and space) based on the observed values. Skill test results reveal that model performances varied over the initialization years and showed comparatively higher scores from the initialization year 1990 and onward. Models with finer spatial resolutions show comparatively better performances as opposed to the models of coarse spatial resolutions where MIROC4h outperformed followed by EC-EARTH and MRI-CGCM3. Comparing the skills, models are divided into three categories (Category-I: MIROC4h, EC-EARTH, and MRI-CGCM3; Category-II: MPI-ESM-LR and MPI-ESM-MR; and Category-III: MIROC5, CanCM4, and CMCC-CM). Three multimodel ensembles’ mean (MMEMs) are formed using the arithmetic mean of Category-I (MMEM1), Category-I and II (MMEM2), and all eight models (MMEM3). The performances of MMEMs are also assessed using the same skill tests and MMEM2 performed best which suggests evaluating the models before the formation of MMEM.

In this review, we will cover a general overview of the current panorama on lncRNAs with an actual or potential role as biological markers in cancer. We will discuss examples of multi-omics approaches that integrates information on somatic aberrations, gene expression and epigenomics, with the scope of providing a more comprehensive view of the functional impact of lncRNA profiles and how these paradigm can be exploited for the discovery and selection of lncRNAs with a functional role and their use as variables informing on progression and prognostic and help guiding the selection of therapeutic strategies for cancers. Finally, we propose a perspective for future evolution of the study of lncRNAs and the discovery of their functional and harnessing their potential to assist in clinical management of malignancies.

Yttrium oxide (Y2O3) resistive random-access memory (RRAM) devices were fabricated using the sol–gel process on indium tin oxide/glass substrates. These devices exhibited conventional bipolar RRAM characteristics, without requiring a high voltage forming process. The effect of current compliance on the Y2O3 RRAM devices was investigated and revealed that as the set current compliance values increased, the resistance values gradually decreased. Consequently, intermediate resistance values were obtained, which are suitable for multi-level cell (MLC) switching. The fabricated Y2O3 RRAM devices were capable of functioning as an MLC with a capacity of 2 bits in one cell, utilizing three low resistance states and one common high resistance state. The potential of the Y2O3 RRAM for neural networks was further explored through numerical simulations. Hardware neural networks based on the Y2O3 RRAM demonstrated effective digit image classification with a high accuracy rate of approximately 88%, comparable to the ideal software-based classification (~92%). This suggests that the proposed RRAM has the potential to be utilized as a memory component in practical neuromorphic systems.

In this work, we propose a self-supervised multi-agent system that meets the online learning of clustering tasks for video behavior recognition spatio-temporal tasks. Encoding visual behavioral actions as discrete temporal sequence(DTS). Real-time clustering recognition task in a multi-agent system for continuous model building, training, and correction. Finally, we implemented a fully decentralized multi-agent system and completed its feasibility verification in a surveillance video application scenario on vehicle path clustering.

Along with the popularity of the Internet, people are exposed to more and more ways of micro-videos, and a huge amount of micro-video data has emerged. micro-videos have gradually become the Internet content preferred by the public, and a large number of micro-video apps have also emerged, such as Tiktok and Kwai. Intelligent classification and mining of micro-videos can greatly enhance user experience, improve business operation efficiency and enhance user experience. Through deep intelligent analysis and mining of micro-videos, important information in micro-videos can be extracted to provide an important basis for beautifying videos, content appreciation, video recommendation, content search, etc. In the past, content understanding for short videos often used human work annotation, but in recent years, with the great success of deep convolutional neural networks in image recognition, short video content understanding based on this method has gradually developed. Nowadays, most recognition algorithms extract the feature representation of each frame independently and then fuse them. However, while extracting the feature representation, some low-level semantic features are lost, which makes the algorithm unable to accurately distinguish the category of the video. At present, the algorithm of micro-video recognition based on deep learning has surpassed the iDT algorithm, making these traditional methods fade out of people’s view. In this paper according to the micro-video classification task, a new network model is proposed to concatenate features of each modality into the overall features of various modalities through the network, and then fuse the various modal features with the attention mechanism to obtain the whole micro-video features, which will be used for classification. In order to verify the effectiveness of the algorithm proposed in this paper, experiments are conducted in the public dataset, and it is shown the effectiveness of our model.

The giant challenge breeding flood-irrigated rice is to identify superior genotypes that present high-yielding with specific grain qualities, resistance to abiotic and biotic stresses, excellent adaptation to the target environment. Thus, the objectives of this study were to propose a bayesian multi-trait model, estimate genetic parameters, and select flood-irrigated rice genotypes with better genetic potentials in different evaluation environments. For this, twenty-five rice genotypes belonging to the flood-irrigated rice improvement program were evaluated. The grain yields, grain length, width and thickness, grain length, and grain width and weight of 100 grains in the agricultural year 2016/2017. The experimental design used in all experiments was a randomized block design with three replications. The Monte Carlo Markov Chain algorithm estimated genetic parameters and genetic values. The grain thickness trait was considered highly heritable, with a credibility interval ranging from: h^2: 0.9480; 0.9440; 0.8610, in environments 1, 2, and 3, respectively. The grain yields showed a low correlation estimate between grain thickness and 100-grain weight, in all environments, with a credibility interval ranging from (ρ= 0.5477; 0.5762; 0.5618 and 0.5973; 0.5247; 0.5632, grain thickness and 100-grain weight, in environments 1, 2, and 3, respectively). The Bayesian multi-trait model proved to be an adequate strategy for the genetic improvement of flood-irrigated. Genotypes 2 and 15 had similar potential in the three environments, they should be selected as high-performance multi-trait genotypes for the genetic breeding of flood-irrigated rice in the program.

Multi-objective optimization (MOO) is an optimization involving minimization or maximization of several objective functions more than the conventional one objective optimization, which is useful in many fields. Many of the current methodologies addresses challenges and solutions that attempt to solve simultaneously several Objectives with multiple constraints subjoined to each. Often MOO are generally subjected to linear inequality, equality and or bounded constraint that prevent all objectives from being optimized at once. This paper reviews some recent articles in area of MOO and presents deep analysis of Random and Uniform Entry-Exit time of objectives. It further break down process into sub-process and then provide some new concepts for solving problems in MOO, which comes due to periodical objectives that do not stay for the entire duration of process lifetime, unlike permanent objectives which are optimized once for the entire process duration. A methodology based on partial optimization that optimizes each objective iteratively and weight convergence method that optimizes sub-group of objectives are given. Furthermore, another method is introduced which involve objective classification, ranking, estimation and prediction where objectives are classified based on their properties, and ranked using a given criteria and in addition estimated for an optimal weight point (pareto optimal point) if it certifies a coveted optimal weight point. Then finally predicted to find how far it deviates from the estimated optimal weight point. A Sample Mathematical Tri-Objectives and Real world Optimization was analyzed using partial method, ranking and classification method, the result showed that an objective can be added or removed without affecting previous or existing optimal solutions. Therefore suitable for handling time governed MOO. Although this paper presents concepts work only, it’s practical application are beyond the scope of this paper, however base on analysis and examples presented, the concept is worthy of igniting further research and application.

This paper addresses a wildlife monitoring problem using a team of UAVs for efficient monitoring of wildlife. The state-of-the-art technology using UAVs has been an increasingly popular tool to monitor wildlife compared to the traditional methods such as satellite imagery-based sensing or GPS trackers. However, there still exist unsolved problems as to how the UAVs need to cover a spacious domain to detect animals as many as possible. In this paper, we propose the optimal transport-based wildlife monitoring strategy for a multi-UAV system, to prioritize monitoring areas while incorporating complementary information such as GPS trackers and satellite-based sensing. Through the proposed scheme, the UAVs can explore the large-size domain effectively and collaboratively with a given priority. The time-varying nature of wildlife due to their movements is modeled as a stochastic process, which is included in the proposed work to reflect the spatio-temporal evolution of their position estimation. In this way, the proposed monitoring plan can lead to efficient wildlife monitoring with a high detection rate. Various simulation results including statistical data are provided to validate the proposed work.

Metabolomics deals with multiple and complex chemical reactions within living organisms and how these are influenced by external or internal perturbations. It lies at the heart of omics profiling technologies not only as the underlying biochemical layer that reflects information expressed by the genome, the transcriptome and the proteome, but also as the closest layer to the phenome. The combination of metabolomics data with the information available from genomics, transcriptomics, and proteomics offers unprecedented possibilities to enhance current understanding of biological functions, elucidate their underlying mechanisms and uncover hidden associations between omics variables. As a result, a vast array of computational tools have been developed to assist with integrative analysis of metabolomics data with different omics. Here, we review and propose five criteria – hypothesis, data types, strategies, study design and study focus – to classify statistical multi-omics data integration approaches into state-of-the-art classes under which all existing statistical methods fall. The purpose of this review is to look at various aspects that lead the choice of the statistical integrative analysis pipeline in terms of the different classes. We will draw a particular attention to metabolomics and genomics data to assist those new to this field in the choice of the integrative analysis pipeline.

The increasing number of robots around us will soon create a demand for connecting these robots in order to achieve goal-driven teamwork in heterogeneous multi-robot systems. In this paper, we focus on robot teamwork specifically in dynamic environments. While the conceptual modeling of multi-agent teamwork has been studied extensively during the last two decades, related engineering concerns have not received the same degree of attention. Therefore, this paper makes two contributions. The analysis part discusses general design challenges that apply to robot teamwork in dynamic application domains. The constructive part presents a review of existing engineering approaches for challenges that arise with dynamically changing runtime conditions. An exhaustive survey of robot teamwork aspects would be beyond the scope of this paper. Instead, we aim at creating awareness for the manifold dimensions of the design space and highlight state-of-the-art technical solutions for dynamically adaptive teamwork, thus pointing at open research questions that need to be tackled in future work.

From ancient time, electric grid system developed as one way direction in which users get the electricity from generators to far end. However, it is not the consumer centric as its one way process and consumer have no way to communicate to the server. Thus, with the development of digital revolution, the grid converted to smart grid and meter converted to smart meter. In smart grid, the protocol follows the bidirectional way of communication with support of consumers in the system. Recently in 2016, Jo et al. proposed the scheme for smart grid system using privacy preserving model and claimed to be efficient and secure. However, in this paper we have analyzed the scheme of Jo et al. and proved that the scheme is vulnerable to Replay attack and afterwards shows the change in protocol to withstand against this attack.

Equality and incomparability multi-label ranking have not been introduced to learning before. This paper proposes new native ranker neural network to address the problem of multi-label ranking including incomparable preference orders using a new activation and error functions and new architecture. Preference Neural Network PNN solves the multi-label ranking problem, where labels may have indifference preference orders or subgroups which are equally ranked. PNN is a nondeep, multiple-value neuron, single middle layer and one or more output layers network. PNN uses a novel positive smooth staircase (PSS) or smooth staircase (SS) activation function and represents preference orders and Spearman ranking correlation as objective functions. It is introduced in two types, Type A is traditional NN architecture and Type B uses expanding architecture by introducing new type of hidden neuron has multiple activation function in middle layer and duplicated output layers to reinforce the ranking by increasing the number of weights. PNN accepts single data instance as inputs and output neurons represent the number of labels and output value represents the preference value. PNN is evaluated using a new preference mining data set that contains repeated label values which have not experimented on before. SS and PS speed-up the learning and PNN outperforms five previously proposed methods for strict label ranking in terms of accurate results with high computational efficiency.

The concept of transit-oriented development (TOD) has been widely recognized in recent years for its role in reducing car traffic, improving public transportation, and enhancing traffic sustainability. This paper conducts empirical research on a developed rail transit network, using Shanghai as a case study. In addition to traditional TOD features, other factors based on urban rail transit are introduced, including multi-level modeling (MLM), which is used to analyze the possible factors influencing rail patronage. To avoid the bias of research results led by the correlation between independent variables, factors are divided into two levels. The first level includes three groups of variables: the built environment, station characteristics, and socioeconomic and demographic characteristics. The second level includes a set of variables which are regional characteristics. Results show that the most significant impact on train patronage is station location in the business district area. Other factors that have a positive effect on promoting rail transit travel include the number of service facilities around the station, degree of employment around the station, economic level, intensity of residential development, if the station is a transfer station, the operating period of the station, and the size of the large transportation hub around the station.

We propose a probabilistic graphical model for discriminative substrate characterization, to support geological and biological habitat mapping in aquatic environments. The model, called a fully connected conditional random field (CRF), is demonstrated using multispectral and monospectral acoustic backscatter from heterogeneous seafloors in Patricia Bay, British Columbia, and Bedford Basin, Nova Scotia. Unlike previously proposed discriminative machine learning algorithms, the CRF model considers both the relative backscatter magnitudes of different substrates and their relative proximities. The model therefore combines the statistical flexibility of a machine learning algorithm with an inherently spatial treatment of the substrate. The CRF model predicts substrates such that nearby locations with similar backscattering characteristics are likely to be in the same substrate class. The degree of proximity and allowable backscatter similarity are controlled by parameters that are learned from the data. CRF model results were evaluated against a popular generative model known as a Gaussian Mixture model that doesn't include spatial dependencies, only covariance between substrate backscattering response over different frequencies. Both models are used in conjunction with sparse bed observations/samples in a supervised classification. A detailed accuracy assessment, including a leave-one-out cross-validation analysis, was performed using both models. Using multispectral backscatter, the GMM model trained on 50% of the bed observations resulted in a 75% and 89% average accuracies in Patricia Bay and Bedford Basin, respectively. The same metrics for the CRF model were 78% and 95%. Further, the CRF model resulted in a 91% mean cross-validation accuracy across four substrate classes at Patricia Bay, and a 99.5% mean accuracy across three substrate classes at Bedford Basin, which suggest that the CRF model generalizes extremely well to new data. This analysis also showed that the CRF model was much less sensitive to the specific number and locations of bed observations than the generative model, owing to its ability to incorporate spatial autocorrelation in substrates. The CRF approach therefore may prove to be a powerful `spatially aware' alternative to other discriminative classifiers.

Aiming at the problems that are poor generalization performance, low retrieval accuracy and large time consumption of existing content-based image retrieval system, the hierarchical image retrieval method based on multi feature fusion is proposed in this paper. The retrieval accuracy rates on Corel5K, UKbeach and Holidays are 68.23(Top 1), 3.73(N-S) and 88.20(mAp), respectively. The experimental results show that the method proposed in this paper can effectively improve the deficiency of single feature retrieval and save time significantly in the premise of a small amount of loss of accuracy.

The variations of visibility, PM mass concentration and mixing layer height (MLH) at four major urban-industry regions (Shenyang, Anshan, Benxi and Fushun) in multi-cities of central Liaoning over northeast China were evaluated from 2009-2012 to characterize the dynamics effect on air pollution. The annual mean visibilities were about 13.7±7.8km, 13.5±6.5km, 12.8±6.1km and 11.5±6.8km in Shenyang, Anshan, Benxi and Fushun, respectively. The pollution load (PM×MLH) shown a weaker vertical diffusion in Anshan with a higher PM concentration in the near-surface. High concentrations of fine mode particles may be partially attributed to the biomass burning emissions from September in Liaoning Province and surrounding regions in Northeast China as well as the coal burning during the heating period with lower MLH in winter. The increasing wind speed has a similar change as the increasing of mixing layer height to make the effect on the aerosol vertical diffusion. The visibility on the non haze-fog days was about 2.5-3.0 times higher than that on hazy and fog days. The fine particle concentrations of PM2.5 and PM1.0 on the haze and fog days were ~1.8-1.9 times and ~1.5 times higher than that on no hazy-fog days. The MLH during fog pollution showed more declining trend than haze pollution compared with non haze-fog days. The results of this study could provide the useful information to better recognize the effects of vertical pollutants diffusion on air quality in the multi-cities of central Liaoning over Northeast China.

Multi-microgrid has many new characteristics, such as bi-directional power flows, flexible operation modes and variable fault currents with different control strategy of inverter interfaced distributed generations (IIDGs). All these featuring aspects pose challenges to multi-microgrid protection. In this paper, current and voltage characteristics of different feeders are analyzed when fault occurs in different positions of multi-microgrid. Based on the voltage and current distribution characteristics of the line parameters, a new protection scheme for the internal fault of multi-microgrid is proposed, which takes the change of phase difference and amplitude of measured bus admittance as the criterion. This scheme with high sensitivity and reliability, has a simple principle and is easy to be adjusted. PSCAD/EMTDC is used in simulation analysis, and simulation results have verified the correctness and effectiveness of the protection scheme.

Bearing fault diagnosis is crucial for ensuring the stable operation of mechanical equipment. With the continuous development of deep learning technology, Convolutional Neural Networks (CNNs) have demonstrated significant advantages in the field of fault diagnosis. This paper proposes a new method that combines various CNN architectures to improve the accuracy of bearing fault diagnosis. We designed five different convolutional network structures, including SerConv, ResConv, One-Shot Aggregation Convolution (OSAConv), Cross-Stage Aggregation Convolution (CSAConv), and MD-DAConv. Experimental results on the Case Western Reserve University (CWRU) bearing dataset show that the proposed method exhibits high accuracy and robustness in fault diagnosis. The results indicate that strategies such as multi-directional, multi-scale, and residual connections play a crucial role in enhancing the depth and breadth of feature extraction, while simple and effective feature fusion and information transmission mechanisms are key to ensuring the robustness and generalization ability of the model.

Based on the definition of double fuzzy relations, two types of new rough set models are constructed, which are multi-granulation double fuzzy rough sets called optimistic and pessimistic multi-granulation double fuzzy rough sets, and some of their properties were studied. In addition, we study the relationship between optimistic and pessimistic multi-granulation double fuzzy rough sets and double fuzzy rough sets.

As the core components of water jet propulsion system, water jet pump, directly affect the ship's propulsion performance. 3D reverse design method can effectively suppress the impeller secondary flow to get better performing hydraulic models. Aiming at fast and efficient optimization of the impellers, we parameterize the impellers and runner, and coupled with optimization algorithms and numerical calculations. It is an efficient and feasible way to coupling optimization based on multi-parameter, multi-objective and optimization algorithms, and parameterizing the impellers and guide vane geometry based on the 3D model designed by 3D reverse design method. In this paper, the waterjet propulsion pump is taken as the research object. According to the design method of the waterjet propulsion pump hydraulic model, the traditional axial flow blade design method, the modern ternary design theory of the blades, and the parametric three-dimensional reverse design method are selected to constructing an optimal design optimization strategy for the impeller of water-jet propulsion pump based on multi-parameter and multi-object genetic algorithm. Under the design conditions, the optimized pump efficiency reaches 89.28%, which is 1.24% higher than the original hydraulic model. The optimized pump head is 13.51 m, which is 0.39m more than the original hydraulic model. Under the design condition, the test measured head is 13.26m, the numerical calculation result is 1.88% higher than the test result, the test measured efficiency is 87.1%, the numerical calculation result is 2.5% higher than the test result. From the test results, the optimized impeller has higher hydraulic performance. Experiments have shown that it is feasible to optimize the design strategy.

Traditional soil characterization methods are time consuming, laborious and invasive and do not allow long-term repeatability of measurements. The overall aim of this paper was to assess and model spatial variability of the soil in an olive grove in south Italy by using data from two sensors of different type: a multi-spectral on-board drone radiometer and a hyperspectral visible-near infrared-shortwave infrared (VIS-NIR-SWIR) reflectance radiometer as well as sample data, to arrive at a delineation of homogeneous areas. The hyperspectral data were processed using continuum removal methodology to obtain information about the content and composition of clay. Differently, the multispectral data were firstly upscaled to the support of soil data using geostatistics and taking into account change of support. Secondly, the two-sensor data were integrated with soil granulometric properties by using the multivariate geostatistical techniques of multi-collocated cokriging and factor cokriging, in order to achieve a more exhaustive and finer-scale soil characterisation. The paper shows the impact of change of support on the uncertainty of soil prediction that can have a significant effect on decision making in Precision Agriculture. Moreover, four regionalised factors at two different scales (two per each scale) were retained and mapped. Each factor provided a different delineation of the field with areas characterised by different granulometry and clay composition. The applied method is sufficiently flexible and could be applied to any number and type of sensors.

Plant geneticists and breeders have used marker technology since the 1980s in quantitative trait locus (QTL) identification. Marker-assisted selection is effective for large-effect QTL but has been challenging to use with quantitative traits controlled by multiple minor effect alleles. Therefore, genomic selection (GS) was proposed to estimate all markers simultaneously, thereby capturing all their effects. However, breeding programs are still struggling to identify the best strategy to implement it into their programs. Traditional breeding programs need to be optimized to implement GS effectively. This review explores the optimization of breeding programs for variety release based on aspects of the breeder’s equation. Optimizations include reorganizing field designs, training populations, increasing the number of lines evaluated, and leveraging the large amount of genomic and phenotypic data collected across different growing seasons and environments to increase heritability estimates, selection intensity, and selection accuracy. Breeding programs can leverage their phenotypic and genotypic data to maximize genetic gain and selection accuracy through GS methods utilizing multi-trait and, multi-environment models, high-throughput phenotyping, and deep learning approaches. Overall, this review describes various methods that plant breeders can utilize to increase genetic gains and effectively implement GS in breeding .

Many complex behaviours in biological systems emerge from large populations of interacting molecules or cells, generating functions that go beyond the capabilities of the individual parts. Such collective phenomena are of great interest to bioengineers due to their robustness and scalability. However, engineering emergent collective functions is difficult because they arise as a consequence of complex multi-level feedback, which often spans multiple length-scales. Here, we present a perspective on how some of these challenges could be overcome by using multi-agent modelling as a design framework within synthetic biology. Using case studies covering the construction of synthetic ecologies to biological computation and synthetic cellularity, we show how multi-agent modelling can capture the core features of complex multi-scale systems and provide novel insights into the underlying mechanisms which guide emergent functionalities across scales. The ability to unravel design rules underpinning these behaviours offers a means to take synthetic biology beyond single molecules or cells and towards the creation of systems with functions that can only emerge from collectives at multiple scales.

Of particular interest is the serendipity of distinctive nonmetallic layered frameworks with the stoichiometry of 1:2 in the binary metallic compounds within inorganic chemistry and materials science. This not only gives rise to the unexpected properties, especially the distinguished superconductivity, as reflected in MgB2, MoB2, NaC2, LaP2 and CeP2, but also strengthens the cognition of the elemental contributions. Although various investigations on the superconducting performances in the alkali, alkaline-earth and rare-earth metal disilicides containing the silicon layers have been reported, the pursuit of superconductors with silicon-planar framework in transition metal disilicides remain unknown up to now. In the present work, crystal structure searches and first-principles calculations were thoroughly conducted in RuSi2 within the pressure range of 0-300 GPa to uncover the novel structures, incredible silicon building block and the amazing properties. The ground orthorhombic Cmca-RuSi2 phase at ambient pressure is a semiconductor with the band gap of 0.485 eV, whose hardness can reach 31.7 GPa. Even more intriguingly, the high-pressure orthorhombic Cmcm-RuSi2 configuration with the fabulous graphene-like silicon-layer, which can be theoretically stabilized with the transformation pressure of 50.97 GPa, can be unexpectedly recovered to ambient pressure. Electron-phonon coupling calculations unravels that it possesses the metallic trait with an estimated Tc value of 1.43 K at 75 GPa, which increases to 10.07 K under ambient pressure. The enhanced Tc stems from the increased density of states at the Fermi level and associated with the coupled vibrations between Ru and the planar Si layer. Meanwhile, the hardness value for Cmcm-RuSi2 is 26.8 GPa under ambient pressure, which further results from the three-dimensional covalent Ru-Si and Si-Si building blocks. The coexistence of superconductivity and high hardness in the Cmcm-RuSi2 configuration under ambient pressure will pave the way for delving into more binary transition-metal silicides and correlated ternary silicides with the profound silicon layers.

Music has been proposed for a long time as a treatment for mental disorders. However, some special types of music or stimulating sounds might induce negative emotions. Herein, 8-week-old male mice were exposed to two specific genres of music, hip-hop (HH) and heavy metal (HM), and construction noise (CN), and a series of behavioral experiments were performed to evaluate the impact of these music or sounds on the emotion of mice. The experiment lasted 1 week in which 8-week-old male mice were used as animal models. We found that long term exposure HM, HH, and CN induced depressive symptoms with a decrease in dopamine receptor 1 and BDNF in the mixture of hippocampus and frontal cortex of mice. Our results have highly addressed that certain special types of sound or music might induce negative emotions and loss of dopaminergic neurons in mice, and it is necessary to intervene in adolescences who are exposed to these music or sounds for a long time.

This study aimed to evaluate the effects of plasma treated metal contaminated water, used for irrigation, on plant growth. Zinc (Zn) is one of the more commonly used metals. It can enter the environment from industrial processes as particles released into the atmosphere or as wastewater discharged into waterways or the ground. Exposure to large amounts of zinc, even for a short time, can seriously affect human health. In this experiment, three different DBD O2 plasma treated zinc contaminated water and a control (tap water) were used, with Arabidopsis thaliana as the model plant. The treatments were: i) Control, ii) Zn water, iii) Zn+O3(30 min), and iv) Zn+O3(60 min). Arabidopsis plant exhibited maximum growth in the Zn+O3(30 min) treatment. All growth parameters, except leaf area, followed this trend: Zn+O3(30 min) > Control > Zn water > Zn+O3(60 min). Gene expression analysis revealed that reduced metal ion stress and controlled oxidation due to active oxygen species contributed to favorable/improved growth of Arabidopsis in the Zn+O3(30 min) treatment. Therefore, 30 minutes of DBD O2 plasma treated zinc contaminated water [Zn+O3(30 min)] can mitigate the adverse effects of excess zinc ions and promote the growth of Arabidopsis plants.

In this study, we demonstrate the direct preparation of dihalo-γ-lactams featuring two distinct halogens from dichloroamides using a novel Atom Exchange Radical Cyclization (AERC) procedure. This method integrates the established Atom Transfer Radical Cyclization with halogen exchange in solution. The technique operates under mild conditions and requires little amounts of metallic copper, serving as both a supplemental activator and reducing agent.

This paper investigates the effects of various process parameters, specifically the substrate temperature, on weld track geometry in Directed Energy Deposition (DED) processes. A specialized experimental setup integrated within a DED machine facilitates controlled thermal conditioning of sample sheets. Through Design of Experiments (DoE) methods, individual weld marks are generated and analysed to assess geometric characteristics. Regression models are constructed to predict machine parameters for desired weld geometry at different substrate temperatures. Validation experiments confirm the accuracy and reliability of the regression models. Results show a consistent trend towards target geometric features across a broad range of substrate temperatures. Despite deviations in measured values, successful fabrication is achieved, demonstrating robust bonding between weld and substrate. Contact angle predictions exhibit precision within a partial temperature range for proper deposition. The developed model offers insights for optimizing DED process parameters to achieve desired weld characteristics, advancing the capabilities and reliability of additive manufacturing technology. Future work aims to refine the regression model and explore additional mathematical relationships for enhanced accuracy. An implication of this work is the potential to vary the local mechanical properties of parts by controlling the temperature profile while maintaining consistent geometric characteristics. By manipulating the substrate temperature, it may be possible to tailor the microstructure and mechanical properties of fabricated components in the future to meet specific requirements in different regions of the part.

Asymmetric lithium salts, such as Lithium (difluoromethanesulfonyl)(trifluoromethanesulfonyl)imide (LiDFTFSI), have been demonstrated to surpass traditional symmetric lithium salts with improved Li+ conductivity and the capacity to generate stable solid electrolyte interphase (SEI) while maintaining compatibility with aluminum (Al0) current collector. However, the intrinsic reductive mechanism through which LiDFTFSI influences battery performance remains unclear and under debate. Herein, the detailed SEI reactions of LiDFTFSI-based electrolytes were investigated by combining density functional theory and molecular dynamics, aiming to clarify the formation process and atomic structure of SEI. Our results show that asymmetric DFTFSI– weakens the interaction between carbonate solvents and Li+, and substantially alter the solvation structure, exhibiting a well-balanced coordination capacity to bis(trifluoromethanesulfonyl)imide (TFSI–). Nanoseconds hybrid molecular dynamics simulation further reveals that the preferential decomposition of LiDFTFSI produces sufficient LiF and Li2O to facilitate a robust SEI. Moreover, the abundant F– generated from LiDFTFSI decomposition accumulates on the Al surface and subsequently combines with Al3+ from the current collector to form AlF3, potentially inhibiting corrosion of the current collector. Overall, these findings elucidate how LiDFTFSI regulates the solvation sheath and SEI structure, advancing the development of high-performance electrolytes compatible with current collector.

In the present work, a predictive modelling and optimization with the adaptive network based fuzzy inference system(ANFIS) modelling of mechanical properties of laser-coated NB/SiC/Ni welds was studied based on Taguchi design by laser cladding. An ANFIS model based on a Sugeno type fuzzy inference system was developed for predicting the hardness properties of SiC/BN/Ni welds by laser cladding with experimental data required for network training and prediction. Based on analysis of variance, three important factors were taken as inputs for the fuzzy logic inferences, while the hardness properties was taken as the output of the ANFIS. The microstructure of welds were analysed using scanning electron microscopy with an energy dispersive X-Ray spectrometer. Highly developed leaf-like dendrites and eutectic crystals were found in some areas of the melting zone for the BN/SiC/Ni weld, which was significantly hardened. The ANFIS model based on Taguchi's design provides a better pattern of response because the predicted and experimental values were highly similar. As a result, a satisfactory result was achieved between the predicted and experimental values of hardness in laser-coated NB/SiC/Ni welds, whereby the success and validity of the method was verified.

The field of fluorescence sensing, leveraging various supramolecular self-assembled architectures constructed from macrocyclic pillar[n]arenes, has seen significant advancement in recent decades. This review comprehensively discusses, for the first time, the recent innovations in the synthesis and self-assembly of pillar[n]arene-based supramolecular architectures (PSAs) containing metal coordination sites, along with their practical applications and prospects in fluorescence sensing. Integrating hydrophobic and electron-rich cavities of pillar[n]arenes into these supramolecular structures endow the entire system with self-assembly behavior and stimulus responsiveness. Employing the host–guest interaction strategy coupled with complementary coordination forces, PSAs exhibiting both intelligent and controllable properties are successfully constructed. This provides a broad horizon for advancing fluorescence sensors capable of detecting environmental pollutants. This review aims to establish a solid foundation for the future development of fluorescence sensing applications utilizing PSAs. Additionally, current challenges and future perspectives in this field are discussed.

3D printing is a non-traditional additive manufacturing process. It is different from the traditional subtractive manufacturing process. It offers exceptional rapid prototyping capabilities and results that traditional subtractive manufacturing methods cannot attain, especially in applications involving curved or intricately shaped components. Despite its advantages, metal 3D printing will face porosity, warpage, and surface roughness issues. These issues will affect the future practical application of the parts indirectly, for example, the structural strength and the parts assembly ca-pability. Therefore, this study compares the qualities of the warpage, weight, and surface rough-ness after milling and grinding processes under the same materials (316L stainless steel) between general rolled steel and 3D additive steel. Experimental results show that 3D printing parts are approximately 13% to 14% lighter than the general rolled steel. The surface roughness performance of 3D printing steel is better than general rolled steel under the same material after milling or grinding processing. The hardness of the 3D printing steel is better than that of the gen-eral rolled steel. The research verifies that 3D additive manufacturing can use surface processing to optimize surface performance and achieve the functions of lightness and hardness.

Yellow nanorod Mg-MOF-74 was obtained by solvothermal synthesis method. XRD、N2 adsorption-desorption isotherms、SEM and TGA results suggest that the particle size of Mg-MOF-74 reaches 400 nm after the introduction of sodium acetate in the precursor of Mg-MOF-74. Besides, the morphology of Mg-MOF-74 was changed from cauliflower to rod particles. At the same time, the BET specific surface area and pore volume of Mg-MOF-74 were also increased a lot. Then the CO2 dynamic adsorption capacity of Mg-MOF-74 was measured by self-made fix bed under 30 ℃、0.1 bar CO2 partial pressure. The results show that the CO2 adsorption capacity of Mg-MOF-74-N2 reaches 3.67 mmol/g and its CO2 adsorption capacity remains unchanged after 10 times CO2 adsorption-desorption cycles.

Crystalline silicon nanomembrane (Si NM) is promising in wearable and implantable bioelectronics due to its electrical and mechanical performances. However, the current explorations are not enough to firmly bridge ultrathin encapsulation strategies with high performance crystalline Si NM based transistors. In this work, we utilized Al2O3/alucone as the ultrathin encapsulation strategies aim to thoroughly investigate the effect of gate dielectric surface area on the electrical performance of crystalline Si NM based metal-oxide-semiconductor capacitors (MOSCAPs). The comparative analysis was implemented on the three types of diameters (Ø) MOSCAPs with and without Al2O3/alucone encapsulation under planar and concave/convex bending conditions. Benefited from the Al2O3/alucone ultrathin encapsulations, the stability of gate leakage current density, and interfacial characteristics were maintained and improved under mechanical bending deformations for MOSCAPs with predefined Ø of 160, 240, and 320 μm compared to the bare MOSCAPs. Combined with the Ø-related mechanical analysis on the maximum strain in the critical layers and the practical measurements, the encapsulated MOSCAPs with Ø 160 μm showed the most stable electro-mechanical performances. The variations for encapsulated MOSCAPs with three types of Ø emerged in the oxide layer and the interface at dielectric/Si NM that were carefully evaluated according to the bending deformations. These findings are significant for leveraging the practical applications in the ultrathin encapsulation strategies for reliable operations of crystalline Si NM based integrated circuits (ICs).

Deep eutectic solvents are a mixture of two or more components, that at a particular composition become liquids at room temperature. When the compounds that constitute the DES are primary metabolites, namely, amino acids, organic acids, sugars, or choline derivatives, the DES are so called natural deep eutectic solvents (NADES). NADES fully represent green chemistry principles. These solvents are highly welcome, as they are obtained from renewable resources, and gratifyingly biodegradable and biocompatible. They are an alternative to room temperature ionic liquids (RTILs). From the pharmaceutical industry point of view, they are highly desirable, but unfortunately have been rarely used despite their enormous potential. In this review, we will look at their impact on the asymmetric catalytic synthesis of key target molecules, via metal-based catalysis, biocatalysis and organocatalysis. In many cases the NADES that have been used are chiral and can even promote enantioselective reactions, this crucial and very exciting aspect will also be discussed and analysed.

Urban gardens have important social, environmental and economic roles in big cities, contributing to their sustainability. However, food production in urban gardens may be compromised due to soil pollution that resulted from decades of industrial non-regulated environmental activity and mobile transport. In this study, 12 soils from the urban agricultural area of Rome (Italy) were analyzed for the metals Be, Ba, Pb, Co, Ni, V, Zn, Hg, Cd, As, Cu, and Cr. All but one of the soils under analysis were characterized by at least one metal concentration above the threshold limit defined by the Italian Legislative Decree 152/2006 (ILD) for agricultural soils. Multivariate analysis showed that the soils could be classified into five clusters: clusters I and II had relatively lower mean metal concentrations; clusters III, IV, and V had relatively higher mean metal concentrations with several metal concentrations above the threshold proposed by ILD. Three factors contributing to the variability of the metal’s concentration in the soils under investigation were identified: geological factor, related with metals As, Ba, Be, and V; anthropogenic factor, related with Pb and Cu; and, a mixed factor related with Co, Cr, Ni, and Zn. High metal content may limit the utilization of urban soils as urban gardens for food production.

Metal-Organic Frameworks (MOFs) have been observed to exclusively eliminate dyes confined within their respective pores. In this investigation, the synthesis of a breathable MOF structure, MIL-88B(Fe), was pursued with the objective of circumventing restrictions on pore size to en-hance its adsorption capabilities. The synthesis of MIL-88B(Fe) was carried out via the assisted solvothermal method at 373 K using inexpensive yet environmentally benign FeCl3.6H2O, 1,4-benzenedicarboxylic acid and DMF as metal precursor, as linker and solvent, respectively. Furthermore, MOF was subjected to extensive analytical characterization using XRD, FT-IR spectroscopy, N2 gas sorption, TGA, and SEM. The experimental data showed that the utilization of MIL-88B(Fe) with a dose level of 5 mg for 180 mins at pH of 9 led to the highest levels of ad-sorption for both dyes with 162.82 mg g-1 for Methylene Blue (MB) and 144.65 mg g-1 for Rho-damine B (RhB), as a result of contrast molecular size between each dye. The Langmuir and Freundlich models demonstrate a correlation with isotherms, while the thermodynamic analysis demonstrated that MIL-88B(Fe) exhibits distinct endothermic and breathable properties. The ef-ficacy of MIL-88B(Fe) adsorbent for MB and RhB in aqueous solutions indicated exceptional performance, stability, and noteworthy reusability performance.

Transportation is the primary consumer of oil, accounting for a significant portion of global energy consumption (34%) and CO2 emissions (40%). Electrifying road transportation is crucial to mitigate the effects of global warming. The abundant potential of renewable energy sources like solar and wind is hindered by their intermittent nature and incongruity with peak energy demands. This calls for the development of sophisticated energy storage solutions. Metal-air batteries (MABs), emerging as viable alternatives to lithium-ion batteries (LIBs), have attracted considerable attention due to their promising applications in the transportation sector. Despite substantial progress in MAB development over the past two decades, overcoming critical challenges such as electrolyte decomposition, carbon cathode degradation, anodic dendrite growth, and air impurities remains essential for their commercial viability. This mini-review provides a comprehensive overview of MAB fundamentals and the challenges associated with their development. The insights presented in this review serve to illuminate the current landscape and future prospects of MABs in the transportation sector.

The paper presents the numerical and experimental results of research aimed at determining the influence of hardness in the range of 50-90 Shore A of layered tools made of elastomeric materials on the possibility of forming Inconel 625 nickel-based alloy sheets. A stamping die made of 90MnCrV8 steel (hardness 60HRC) was designed for forming embosses in drawpieces, ensuring various stress states on the cross-section of the formed element. The principle of operating the stamping die was based on the Guerin method. Finite element-based numerical modelling of the forming process for various configurations of polyurethane inserts was also carried out. The drawpieces obtained by sheet forming were subjected to geometry tests using optical 3D scanning. The results confirm that in the case of forming difficult-to-deform Inconel 625 Ni-based alloy sheets, the hardness of the polyurethane inserts significantly affects the geometric quality of the obtained drawpieces. The assumptions made in numerical simulations were verified in experimental studies. Based on the test results, it was concluded that the selection of polyurethane hardness should be determined by the shape of the formed element. Significant non-uniform sheet metal deformation was also found, which may pose a problem in the process of designing forming tools and technology of plastic forming of Inconel 625 Ni-based alloy sheets.

This review article deals with the pathways of cellular and global molybdate distribution in plants, especially with a full overview for the model plant Arabidopsis thaliana. In its oxidized state as bioavailable molybdate, molybdenum can be absorbed from the environment. Especially in higher plants, molybdenum is indispensable as part of the molybdenum cofactor (Moco), which is responsible for functionality as a prosthetic group in a variety of essential enzymes like nitrate reductase and sulfite oxidase. Therefore, plants need mechanisms for molybdate import and transport within the organism, which is accomplished via high-affinity molybdate transporter (MOT) localized in different cells and membranes. Two different MOT-families were identified. Especially legumes like Glycine max or Medicago truncatula have an increased numbers of MOT1-family members for supplying their symbionts with molybdate for nitrogenase activity. In Arabidopsis thaliana especially, the complete way of molybdate through the plant is traceable. Not only the uptake from soil by MOT1.1 and its distribution to leaves, flowers and seeds by MOT2-family members was identified, but also inside the cell the transport trough the cytoplasm and the vacuolar storage mechanisms depending on glutathione were described. Finally, supplying the Moco biosynthesis complex by MOT1.2 and MOT2.1 was demonstrated.

Platinum group metals (PGMs) high-grade ore tonnage from Merensky reef keeps on depreciating forcing the metallurgical industry to explore beneficiating PGMs from upper group 2 (UG2) ore which has up to 60% content of chromite and from secondary sources. The PGMs are naturally associated with base metal sulphides and the efficacy of the PGMs extraction processes is dependent on the processing of PGMs-bearing base metal sulphides. These processes include concentrating PGMs-bearing base metal sulphides through flotation, oxidation, etc. prior the metal extraction processes. The evolving mineralogy of PGMs ores has necessitated the use of multiple reagents to enhance the efficiency of the concentration process. This has led to an increased amount of inor-ganic chemicals disposal to the environment and the processing of PGMs to be less economic. Bio-technology has been investigated as a potential low cost, ecologically safe substitute for many current minerals processing methods. The metabolites produced by microorganisms have been used for many years with great success in the leaching and flotation of metals from medium and low-grade sulphide minerals. The possible application of microorganism mainly Acidithiobacillus ferrooxidans (A. ferrooxidans) in the metallurgical processing of PGMs-bearing base metal sulphides is systematically reviewed in this paper. The main emphasis is on the use of A. ferrooxidans in bio-oxidation and bioleaching, as well as their potential to substitute inorganic reagents in the flo-tation of PGMs-bearing base metal sulphides from primary and secondary sources

Date palm trees generate large amounts of various types of waste, including leaf sheath fibers which can be used as a low-cost, precursor for production of biochar including activated carbon (AC) that can be employed for adsorption of contaminants. In the current study, activated carbon was made from leaf sheath fibers of date palm (LSDPFAC) by use of chemical activation with K2CO3, combined with microwave irradiation, characterized and evaluated for its adsorptive capacity of lead ions (Pb2+). The Brunauer–Emmett–Teller (BET) surface area, Langmuir surface area, total pore volume and average pore diameter of LSDPFAC were 560.20 m2/g, 744.31 m2/g, 0.29 cm3/g and 2.47 nm respectively. When the initial concentrations of Pb2+ were increased from 1 to 10 mg/L, Pb2+ adsorption increased from 0.97 to 8.76 mg/g, dry mass (dm) while the percent of Pb2+ removed decreased from 96.70 to 87.60%. The greatest removal of Pb2+ occurred at pH 13 with adsorption capacity of 9.15 mg/g, dm. Results of isotherm and kinetic studies demonstrated that adsorption of Pb2+ onto LSDPFAC was best described by the Freundlich isotherm and pseudo-second order (PSO) models. Langmuir monolayer adsorption capacity, Qm was 14.10 mg/g. Thermodynamic parameters of H°, S°, G° and Ea were 6.39 kJ/mol, 0.12 kJ/mol.K, -31.28 kJ/mol and 15.90 kJ/mol, respectively, which demonstrated that adsorption of Pb2+ by LSDPFAC was endothermic, spontaneous and governed by physisorption.

Microwave absorbers with lightweight, good stability and high efficiency have attracted much attention for their applications in many contemporary fields. In this work, the 3D porous (Ni@NO-C)n/NO-C composite absorber was prepared by a wet chemistry method with Ni chains and melamine as precursors, in which NO-C (N,O-doped carbon) encapsulated Ni particles are homogenously dispersed in the 3D porous networks of NO-C in the form of (Ni@NO-C)n chains. The special microstructure of the as-prepared material is proved to be benefit for the improvement of its microwave adsorption performance. The as-synthesized (Ni@NO-C)n/NO-C composite ab-sorber exhibited an effective absorption bandwidth of 4.1 GHz and an extremely large reflection loss of -72.3 dB. The excellent microwave absorbing performances can be ascribed to the coopera-tive consequence of dielectric loss and magnetic loss along with the balance between attenuation capability and impedance match.

Due to increasing concerns about global warming and energy crisis, intensive efforts have been made to explore renewable and clean energy sources. Single-atom metals and two-dimensional (2D) nanomaterials have attracted extensive attention in the fields of energy and environment because of their unique electronic structures and excellent properties. In this review, we sum-marize the state-of-art progress on the single-atom metal supported at 2D MoS2 (single-atom metal/2D MoS2) for electrochemical CO2 reduction and water splitting. First, we introduce the advantages of single-atom metal/2D MoS2 catalysts in the fields of electrocatalytic CO2 reduction and water splitting, followed by the strategies for improving electrocatalytic performances of single-atom metal/2D MoS2 hybrid nanomaterials and the typical preparation methods. Further, we discuss the important applications of the nanocomposites in electrocatalytic CO2 reduction and water splitting via some typical examples, particularly focusing on their synthesis routes, modification approaches, and physiochemical mechanisms for improving their electrocatalytic performances. Finally, our perspectives on the key challenges and future directions of exploring high-performance metal single-atom catalysts are presented based on recent achievements in the development of single-atom metal/2D MoS2 hybrid nanomaterials.

Abstract Aims: In recent years, electro kinetic (EK) remediation has become more popular as a novel method for removing chromium contamination from soil. This approach, however, is ineffective since it uses both cationic and anionic forms of chromium. In this work, a membrane –based technique was employed to increase the efficiency of the electro kinetic removal of chromium. Methods: Chromium removal from polluted sludge was studied in four bench-scale experiments, two of which used distilled water (EK-1, EK2 & Membrane) and two of which used acetic acid as a catholyte (EK-3, EK4 &Membrane). Results: The pH, total chromium, and fractionation of chromium in the sludge were measured after remediation. In the EK-1, EK-2 & Membrane and EK-3, EK-4 & Membrane trials, the average removal efficiency of total chromium was 47.6%, 58.6%, and 74.4%, 79.6%, respectively. Conclusion: In contrast to the electro kinetic remediation strategy, which left approximately 80% of the sludge neutral or alkaline after treatment, the use of the membrane created acidic soil conditions throughout the sludge. For example, the high field intensity used in the membrane tests may have helped to facilitate chromium desorption, dissolution and separation from the sludge, as well as enhance chromium mobility. The findings show that the membrane can improve the effectiveness of chromium removal from sludge when utilized in the EK remediation process.

Nanostructured transition metal nitrides (TMNs) have been considered a promising substitute for precious metal catalysts toward ORR due to their multi-electron orbitals, metallic properties, and low cost. To design TMNs catalysts with high catalytic activity toward ORR, the intrinsic features of the influencing factor on the catalytic activity toward ORR of nanostructured TMNs need to be investigated. In the paper, titanium nitride (TiN), zirconium nitride (ZrN), and hafnium nitride (HfN) nanoparticles (NPs) are high-efficiency and one-step synthesized by the direct current arc plasma. TiN, ZrN, and HfN NPs with an oxidation layer are applied as the catalysts of hybrid sodium-air batteries (HSABs). The effect of composition and structure attributes of TMNs on ORR catalysis is defined as follows. (ⅰ) Composition effect. With the increase of the oxygen content, the catalytic ORR capability of TMNs decreases progressively due to the reduction of oxygen adsorption capacity; (ⅱ) Structure effect. The redistribution of the density of states (DOS) of ZrN indicates higher ORR activity than TiN and HfN. HSABs with ZrN exhibit an excellent cyclic stability up to 137 cycles (about 140 h), an outstanding rate performance, and a specific capacity of 2817 mAh·g−1 at 1.0 mA·cm−2.

In interceptive treatments in which impacted teeth (incisor or first permanent molar) should be included into the dental arch, the main clinical problem is the provision of an anchorage area and a suitable appliance. The use of laser sintered metal orthodontic grids, designed and printed digitally, has expanded the boundaries of orthodontic treatment, especially in its interceptive phase. Our aim is to describe a digital model for providing anchorage during orthodontic-surgical traction of impacted teeth in the mixed dentition period. We present the treatment of three clinical cases with digitally projected and printed metal grids used for anchorage. In the described clinical cases, individually designed anchorage systems were used. They were created through design software and after that the metal grids were printed. The devices are placed in the oral area and don’t disturb the aesthetics of the patient in any way. The advantages of individual designed metal support grids allow to accommodate the features of relief of the hard palate and alveolar bone. This makes the grids comfortable for the patient and rigid enough to perform orthodontic tractions at the same time. The printed additional grids are applicable in mixed dentition and in complicated clinical cases in permanent dentition. Their individuality allows segmental treatments or treatments in cases requiring additional anchorage further from the active force.

Oxygen evolution reaction is a momentous part of electrochemical energy storage and conversion devices such as rechargeable metal-air batteries. It is particularly urgent to develop low-cost and efficient electrocatalysts for oxygen evolution reactions. As a potential substitute for noble metal electrocatalysts, transition metal selenides are still challenging in improving the activity of oxygen evolution reaction and the research of reaction intermediates. In this study, a simple one-step solvothermal method was used to prepare a polymetallic compound carbon matrix composite (Co9Se8/Ni3Se4/Fe3O4@C) with a multilayered nanosheets structure. It exhibited good OER activity in an alkaline electrolyte solution with an overpotential of 268 mV at 10 mA/cm2 in an alkaline medium. Besides, this catalyst also showed excellent performance in the 24 hours stability test. The composite presents a multi-layer sheet structure, which effectively improves the contact between the active site and the electrolyte. The selenide formed by Ni and Co has a synergistic effect, Fe3O4 and Co9Se8 form a heterojunction structure, which can effectively improve the reaction activity by initiating the electronic coupling effect through the interface modification. In addition, carbon quantum dots have rich heteroatoms and electron transferability, which improves the electrochemical properties of the composites. This work provides a new strategy for the preparation of highly efficient OER electrocatalysts utilizing the multimetal synergistic effect.

The reckless use of non-replenishable fuels by the growing population for energy and the resultant incessant emission of hazardous gases and waste products into the atmosphere insisted scientists to fabricate materials capable of managing these global threats at once. In recent studies, photo-catalysis employed focus on utilizing renewable solar energy to initiate chemical processes with the aid of semiconductors and highly selective catalysts. A wide range of nanoparticles have showcased promising photocatalytic properties. Ultrasmall metal nanoclusters (MNCs) with sizes below 2 nm, stabilized by ligands shows discrete energy levels, exhibits unique optoelectronic properties which are vital to photocatalysis. In this review, we intend to compile information on varying photocatalytic efficiency of metal NCs with respect to changes in their properties. Review discusses about the photocatalytic activity of atomically precise ligand-protected MNCs and its hybrids in the domain of in energy conversion processes like photodegradation of dyes, Oxygen Evolution Reaction (ORR), Hydrogen Evolution Reaction (HER) and CO2 Reduction Reaction (CO2RR), and photosensitizer in solar cell.

Metal-organic frameworks (MOFs) are investigated for the oxygen evolution reaction (OER) due to their structure diversity, high specific surface area, adjustable pore size and abundant active sites. However, the poor conductivity of most MOFs restricts this application. Herein, through a facile one-step solvothermal method, the Ni-based pillared metal-organic framework [Ni2(BDC)2DABCO] (BDC = 1,4-benzenedicarboxylate, DABCO = 1,4-diazabicyclo[2.2.2]octane), its bimetallic nickel-iron form [Ni(Fe)(BDC)2DABCO] and their modified Ketjenblack (mKB) composites were synthesized and tested towards OER in an alkaline medium (KOH 1 mol L–1). A synergistic effect of the bimetallic nickel-iron MOF and the conductive mKB additive enhance the catalytic activity of the MOF/mKB composites. All MOF/mKB composite samples (7, 14, 22, 34 wt.% mKB) indicated much higher OER performances than the MOFs and mKB alone. The Ni-MOF/mKB14 composite (14 wt. % of mKB) demonstrated an overpotential of 294 mV at a current density of 10 mA cm–2 and Tafel slope of 32 mV dec–1, which is comparable with commercial RuO2 commonly used as a benchmark material for OER. The catalytic performance of Ni(Fe)MOF/mKB14 (0.57 wt% Fe) was improved further to an overpotential of 279 mV at a current density of 10 mA cm–2. The low Tafel slope of 25 mV dec–1 as well as a low reaction resistance due to electrochemical impedance spectroscopy (EIS) measurement confirm the excellent OER performance of the Ni(Fe)MOF/mKB14 composite. For practical applications, the Ni(Fe)MOF/mKB14 electrocatalyst was impregnated into commercial nickel foam (NF), where overpotentials of 247 and 291 mV at current densities of 10 and 50 mA cm–2, respectively, were realized. The activity was maintained for 30 h at the applied current density of 50 mA cm–2. The electrocatalytic system consisting of earth-abundant Ni and Fe metals only would be attractive for the development of efficient, practical and economical energy conversion materials for efficient OER activity.

The microstructure evolution, superplasticity, and room temperature mechanical properties of Ti-4%Al-1%V-3%Mo alloys modified with 0.01-2 wt.% boron were investigated. Increasing the boron content from 0 to 0.1 wt.% effectively refined prior β-grains, reducing a mean grain size from ~700 µm to ~210 µm. Whiskers of the TiB phase with a size in a range of 0.7-2.9 µm were observed after solidification and thermomechanical processing. Alloys with 0.01-0.1 wt.% boron exhibited similar superplastic elongations and strain rate sensitivity coefficient m of 0.4-0.5 at a strain rate of 1×10-3 s-1 and the elongation to failure decreased from 1000% at 875°С to 400-500% at 700°С. Along with this, the minor boron addition effectively decreased flow stress values, especially at 775 °C, that was explained by the acceleration of the recrystallization and globularization of the microstructure at the initial stage of deformation. Recrystallization-induced decrease in yield strength from 770 MPa to 680 MPa was observed with an increase in boron content from 0 to 0.1 wt.%. Heat treatment increased post-forming strength characteristics for the alloys with 0.01-0.1 wt.% boron by 90–140 MPa without ductility reduction. Alloys with 1-2 wt.% B demonstrated the opposite behavior. The grain refinement effect was not revealed, and prior β grain sizes were ~670-750 µm after solidification. Thermomechanical processing promoted the fragmentation of boride whiskers and the formation of near-spherical particles with a size of ~1 μm for the alloy with a eutectic concentration of 2 wt.% B. A high fraction of borides, ~5-11%, in the alloys with 1-2 wt.% B deteriorated the superplastic properties and drastically decreased ductility at room temperature. The alloy with 2 wt.% B demonstrated non-superplastic behavior and a low level of mechanical properties, meanwhile, the alloy with 1% boron exhibited high-temperature superplasticity at 875 °C with elongation of ~500%, and yield strength of 830 MPa, ultimate tensile strength of 1020 MPa at a room temperature after 100% of superplastic deformation.

In spite of large-scale investigations of homogeneous single-site metallocene catalysts and systems based on them, the problem of controlling their activity, chemo- and stereoselectivity with the aim of developing efficient methods for the preparation of practically useful products of alkenes transformation, such as dimers, oligomers, and polymers, still remains topical. Here we studied catalytic activity of differently structured zirconocenes (10 examples of cyclopentadienyl and indenyl complexes) and co-catalysts activating the system, namely HAlBui2, MMAO-12 or (Ph3C)[B(C6F5)4] at low activator/Zr ratios in 1-hexene oligomerization reaction. The influence of catalyst structure and system composition on alkene conversion, type of products formed and reaction stereoselectivity was investigated. The composition of hydride intermediates forming in the systems L2ZrCl2 (L2= ansa-Me2CCp2)-HAlBui2-activator was studied by NMR and the participation of biszirconium hydride complex as the precursor of catalytically active sites of the alkene dimerization reaction was shown.

By drilling periodic thru-holes in a suspended film, the phonon system can be modified. Being motivated by the BCS theory, the technique, so-called phonon engineering, was applied to a niobium sheet. The newly emergent high-T_c superconductivity, however, cannot be accounted for by the BCS theory. Rather, its exposed configuration, namely a square-lattice oxygen network, is reminiscent of the copper--oxygen plane in cuprate high-T_c superconductors. It turns out that its magnetic result is consistent with the principle of giant atom, which was developed by another heroes of superconductivity, Fritz London and John Slater, in the 1930s, several decades earlier than the propagation of BCS theory. The superconducting transition feature is discussed on the basis of a comprehensive theory of the giant atom---the theory of hole superconductivity.

As one of the representatives of emerging metallic transition metal dichalcogenides, niobium ditelluride (NbTe₂) has attracted intensive interest recently due to its distorted lattice structure and unique physical properties. Here, we report on the ultrafast carrier dynamics in NbTe₂ measured using time-resolved pump-probe transient reflection spectroscopy. A thickness-dependent carrier relaxation time is observed, exhibiting a clear increase in the fast and slow carrier decay rates for thin NbTe₂ flakes. In addition, pump power dependent measurements indicate that the carrier relaxation rates are power-independent, with the peak amplitude of the transient reflectivity increasing linearly with pump power. Isotropic relaxation dynamics in NbTe₂ is also verified by performing polarization-resolved pump-probe measurements. These results provide an insight into the light-matter interactions and charge carrier dynamics in NbTe₂ and will pave the way for its applications to photonic and optoelectronic devices.

The powder bed fusion (PBF) metal additive manufacturing (AM) method uses an energy source like a laser to melt the metal powders. The laser can locally melt the metal powders and creates a solid structure as it moves. The complexity of the heat distribution in laser PBF metal AM is one of the main features that need to be accurately addressed and understood to design and manage an optimized printing process. In this research, the dependency of local thermal rates and gradients on print after solidification (in the heat-affected zone) was numerically simulated and studied to provide information for designing the print process. The simulation results were validated by independent experimental results. The simulation shows that the local thermal rates are higher at higher laser power and scan speed. Also, the local thermal gradients increase if the laser power increases. The effect of scan speed on the thermal gradients is opposite during heating versus cooling times. Increasing the scan speed increases the local thermal gradients in the cooling times and decreases the local thermal gradients during the heating. In addition, these simulation results could be used in artificial intelligence (AI) and machine learning for developing digital additive manufacturing.

In the design and development of novel materials that have excellent mechanical properties, classification and regression methods have been diversely used across mechanical deformation simulations or experiments. The use of materials informatics methods on large data that originate in experiments or/and multiscale modeling simulations may accelerate materials discovery or develop new understanding of materials’ behavior. In this fast-growing field, we focus on reviewing advances at the intersection of data science with mechanical deformation simulations and experiments, with a particular focus on studies of metals and alloys. We discuss examples of applications, as well as identify challenges and prospects.

Description of redox reactions is critically important for understanding and rational design of materials for electrochemical technologies including metal-ion batteries, catalytic surfaces, or redox-flow cells. Most of these technologies utilize redox-active transition metal compounds due to their rich chemistry and their beneficial physical and chemical properties for these types of applications. A century since its introduction, the concept of formal oxidation states (FOS) is still widely used for rationalization of the mechanisms of redox reactions, but there exists a well-documented discrepancy between FOS and the electron density-derived charge states of transition metal ions in their bulk and molecular compounds. We summarize our findings and those of others which suggest that density-driven descriptors are in certain cases better suited to characterize the mechanism of redox reactions, especially when anion redox is involved, which is the blind spot of the FOS ansatz.

Copper is a heavy metal used in many industries and known for its negative impacts on the environment and human’s health. A novel structured metal organic framework (MOF) was used for copper adsorption for this work. SEM, EDAX, XRD and FTIR were done to confirm the structure of MOF prepared. MOF of 0.05 gm was used to examine its ability in Cu+ 2 removals with different initial concentrations of Cu+2 and pH values (5, 7 and 9). The prepared MOF was able to achieve Cu removal with 94.6%, 93%, 91.5%, and 92.5 % for the initial concentrations of 5, 10, 15, and 20 ppm respectively. It also performed very well for pH 5 and 7 with average removal ranging from 93.9%-95% for pH 5 and 7 for the initial concentrations of 5, 10, and 15 respectively which indicate that the prepared MOF is of high ability in Cu+ 2 removal.

The response of a single tin oxide nanowire was collected at different temperatures to create a virtual array of sensors working as a nano-electronic nose. The single nanowire, acting as a chemiresistor, was first tested with pure ammonia and then used to determine the freshness status of trout fish (Oncorhynchus mykiss) in a rapid and non-invasive way. The gas sensor reacts to total volatile basic nitrogen, detecting the freshness status of the fish samples in less than 30 seconds. The sensor response at different temperatures correlates well with the total viable count (TVC), demonstrating that it is a good (albeit indirect) way of measuring the bacterial population in the sample. The nano-electronic nose is able to classify the samples according to their degree of freshness, but also to quantitatively estimate the concentration of microorganisms present. The system was tested with samples stored at different temperatures, managing to classify them perfectly (100%) and estimating their log(TVC) with an error lower than 5%.

Additive manufacturing (AM) is an emerged layer-by-layer manufacturing process. However, its broad adoption is still hindered by limited material options, different fabrication defects, and inconsistent part quality. Material extrusion (ME) is one of the most widely used AM technologies, and, hence, is adopted in this research. Low-cost metal ME is a new and AM technology used to fabricate metal composite parts using sintered metal infused filament material. Since the involved materials and process are relatively new, there is a need to investigate the dimensional accuracy of ME fabricated metal parts for real-world applications. Each step of the manufacturing process, from the material extrusion to sintering, might significantly affect the dimensional accuracy. This research provides a comprehensive analysis of dimensional changes of metal samples fabricated by the ME and sintering process, using statistical and machine learning algorithms. Machine learning (ML) methods can be used to assist researchers in sophisticated pre-manufacturing planning and product quality assessment and control. This study compares linear regression to neural networks in assessing and predicting the dimensional changes of ME made components after 3D printing and sintering process. The prediction outcomes using a neural network performed the best with the highest accuracy as compared to regression. The findings of this study can help researchers and engineers to predict the dimensional variations and optimize the printing and sintering process parameters to obtain high quality metal parts fabricated by the low-cost ME process.

Abstract: This work is part of the interest of solving the problems of water contamination with last generation pollutants, for which a novel and in an aqueous medium FeBTC material incorporated with magnetite nanoparticles was proposed. That material was synthesized by in situ solvothermal method, the Fe3O4 nanoparticles were added during the Fe-BTC MOF synthesis and used in the drug’s adsorption. The materials were characterized by XRD, FTIR and Raman spectroscopy, and N2-physisorption at 77 K. Fe3O4-FeBTC material showed a maximum adsorption capacity of 357.1 mg g−1 for diclofenac sodium, 70.9 mg g−1 for naproxen sodium, and 122.9 mg g−1 for Ibuprofen. A pseudo-second-order kinetic model can describe the adsorption process, and the thermodynamic study revealed that the adsorption of the three drugs was a feasible, spontaneous, and exothermic process. The incorporation of magnetite nanoparticles in the FeBTC considerably increased the adsorption capacity of pristine FeBTC. Also, hybridization of the FeBTC with magnetite nanoparticles reinforced the most vulnerable part of the MOF, increasing its thermal and aqueous media stability. The electrostatic interaction, H-bonding, and interactions in the open-metal sites played a vital role in drug adsorption. The competition of sites in the multicomponent mixture's adsorption showed selective adsorption at diclofenac sodium and naproxen sodium.

Selective laser melting (SLM) is a commonly used laser powder bed technique where the final properties are influenced by many different powder related properties, such as particle size distribution, chemical composition and flowability. In applications where high hardness, wear resistance, strength and good heat properties are required, high speed steels (HSS) are widely used today. HSS has high carbon content and are therefore considered as unweldable. The rapidly growing implementation of AM technologies has led to a growing range of new applications and demands for new alloys and properties. The interest in being able to manufacture HSS by SLM without cracking is therefore increasing. In SLM, it is possible to preheat the base plate to a few hundred degrees Celsius which has been used for HSS and proved successful due to reduced thermal gradients. In this study, the properties of SLM produced high speed steel PEARL Micro®2012 with a carbon content of 0.61 wt.-% have been investigated and compared to those of a forged and rolled PM-HIP counterpart ASP®2012.

The development of numerical simulations is potentially useful in predicting the most suitable manufacturing process and ultimately improving product quality. Seamless pipes are manufactured by rotary piercing process in which round bars are fed between two rolls and pierced by a stationary plug. During this process, the material undergoes severe deformation which renders it impractical to be modelled and analysed with conventional finite element methods. In this paper, three dimensional numerical simulations of the piercing process are performed with Arbitrary Lagrangian-Eulerian (ALE) Formulation in LS DYNA software. Details about the material model as well as the elements formulations are elaborated here and mesh sensitivity analysis was performed. The results of the numerical simulations are in good agreement with experimental data found in the literature and the validity of the analysis method is confirmed. The effects of varying workpiece velocity, process temperature, and wall thickness on the maximum stress levels of the product material/pipes are investigated by performing simulations of sixty scenarios. Three dimensional surface plots are generated which can be utilized to predict the maximum stress value at any given combination of the three parameters.