Moisture and thermal are the key factors for influencing methane desorption during CBM exploitation. Using high pressure water injection technology into coalbed, new fractures and pathways are formed to methane transport. It is existed a phenomenon of water inhibiting gas flow. This study is focused on various water pressures impacted on gas adsorbed coal samples, then the desorption capacity could be revealed under different conditions. And the results are shown that methane desorption capacity was decreased with water pressure increased at room temperature and the downtrend would be steady until water pressure was large enough. Heating could promote gas desorption capacity effectively, with the increasing of water injection pressures, the promotion of thermal on desorption became more obvious. These results are expected to provide a clearer understanding of theoretical efficiency of heat water or steam injection into coalbed, they can provide some theoretical and experimental guidance on CBM production and methane control.

The problem of energy poverty, when energy becomes unaffordable for some population group, is not only a problem for developing countries, but this phenomenon is appearing more and more often in European countries as well. In Europe, it is estimated that 50 to 125 million people are at risk of energy poverty. We hear more and more about energy poverty in connection with the current energy crisis and rising energy prices, but also as a result of insufficient use of renewable energy sources. Due to rising energy prices, we are increasingly hearing about deepening energy poverty in Slovakia as well. The aim of the contribution is to examine the development of energy poverty in Slovakia compared to other EU countries. The situation is studied from the view of the number of days of heating and cooling, the percentage of the population that cannot maintain adequate heat at home, the percentage of the population that has a lack of heat and the percentage of residents without enough heat. During the research, we used distribution analysis, trend analysis, analysis of variance and one-way analysis. The main results show that HDD index recorded decrease, CDD index recorded increase, and Energy poverty is most obvious in low-income group of inhabitants, having shortage of heat, when RES use contribute to mitigation of energy poverty. Solving the unfavorable situation with energy poverty is possible by increasing the share of Renewable energy sources in the gross final energy consumption for heating and cooling, primarily in residential buildings. The results provide information for policy makers in area of economic, social and environmental decision-making.

Climate change has become a major agenda item in international relations and in national energy policy-making circles around the world. This article studies the surprising evolution of the energy policy, and more particularly the energy transition, currently happening in the Arabian Gulf region, which features some of the world’s largest exporters of oil and gas. Qatar, Saudi Arabia and other neighboring energy exporters, plan to export blue and green hydrogen across Asia as well as towards Europe in the years and decades to come. Although poorly known and understood abroad, this recent strategy doesn’t threaten the current exports of oil and gas (still needed for a few decades) but prepares the evolution of their national energy industries towards the future decarbonized energy demand of their main customers in East and South Asia, and beyond. The world’s largest exporters of Liquefied Natural Gas, Qatar, has established industrial policies and projects to upscale CCUS, which can enable blue hydrogen production, as well as natural carbon sinks domestically via afforestation projects.

It's a method to achieve energy savings in single-phase active power greater than that obtained with the "Fan Law" in electric machines applied to ventilation. Quantitative analysis methods were based on electrotechnical techniques, practiced with the corresponding laboratory equipment on the working materials (three prototypes of electric machines). The results obtained from experimentation on the test bench were recorded in tables that collect data of formulas, values, and physical units. The discussion provides a comprehensive comparative study, mainly between power (watts), active energy consumption (kWh), and rotational speed (revolutions per minute). The permanent magnet synchronous motor (PMSM) with the coupling of an RL circuit design does mechanical work at its maximum speed of 3000 (RPM) with only 6.3 (Watts), which is equivalent to 25.2% of the active power required by the single-phase induction asynchronous motor (or shaded pole motor), which required 25 (Watts) to rotate at 1690 (RPM). This translates to 75% lower active power with a 44% superiority in speed, resulting in a 75% savings in single-phase active energy (measured in kWh). The same occurs when comparing it to the universal AC motor (with brushes and wound rotor) to maintain a speed of 3000 (RPM); since it consumes 64.8 (Watts), which is 90.3% more single-phase active energy than that required to achieve the same rotational speed as the permanent magnet synchronous motor (PMSM). The study was conducted on all motors with the same impeller blade diameter and under identical air temperature and atmospheric pressure conditions.

In the traditional power system, customers respond to their primary electricity consumption pattern based on price or incentive to take additional advantages. By developing energy hubs (EHs) where electricity, heat, natural gas and other forms of energy are coupled together, all types of energy customers even the inelastic loads can participate in demand response (DR) program. This novel vision has led to the concept of "integrated demand response (IDR)". IDR programs (IDRPs) in EHs involve coordinating multiple DR activities across different energy systems, such as buildings, industrial complexes, and transportation networks. The main purpose of IDR is that multi-energy users can respond not only by shifting or reducing energy consumption from the demand side, but also by changing the type of energy consumed, in response to the dispatching center. The integration of IDRPs in EHs can help to reduce energy costs, improve grid stability, and increase the penetration of renewable energy sources (RES) in the power system. Moreover, by synchronizing DR activities across different energy systems, IDRPs can provide additional benefits, such as improved energy efficiency, reduced greenhouse gas emissions, and increased resilience to power outages and other disruptions. In this paper, we provide a review, assessment, and classification of fundamental principles, modeling techniques and optimization methods for IDR programs in EHs.

This paper is devoted to an accurate determination of the London dispersive and polar free energy of adsorption, the two Lewis acid γs+ and base γs- components of polar surface energy γsAB of 2D single-crystalline and polycrystalline covalent organic frameworks such as TAPPy-TPA-COFs. Inverse gas chromatography (IGC) at infinite dilution was used to quantify the different surface parameters of the different materials. From IGC measurements, one determined the net retention time of the adsorption of n-alkanes and several polar solvents on single-crystalline and polycrystalline covalent organic frameworks. The free surface Gibbs energy of adsorption was obtained for the various organic molecules at different temperatures from their net retention volume values. The separation between the London dispersive energy and the polar energy of adsorbed molecules was carried out by using a new thermodynamic parameter PSX chosen as new indicator variable and taken into account the deformation polarizability and the harmonic mean of the ionization energies of solvents and solid materials, derived from London dispersion equation. The obtained results are very promising for the accurate determination of the surface thermodynamic parameters of adsorption of organic solvents on solid surfaces.

Since the Paris Agreement in 2016, the goals of limiting climate change and moving toward climate resilience stand. With a share of about \SI{80}{\percent} of global \ce{CO2} emissions, the energy sector is an essential driver for these goals. A shift to low-carbon energy production and a decentralized system for more efficient energy transmission distribution is necessary. In this paper, we present our work on Modeling of Power Exchanges, Algorithms for \ac{LEM}, Competitiveness of \ac{CHP} and Energy Feedback Devices. The study was conducted considering technical, economic, social and regulatory framework. For easy integration into energy simulations or a \ac{DEMS}, a model for power exchanges was created that allows flexible input or deterministic price patterns. The algorithm handles the clearing of an \ac{LEM} by a district aggregator using limit orders with the goal of increasing the share of locally consumed electricity using economic incentives. An investigation was conducted into the operation of flexible \acp{CHP} in low-carbon power systems to balance the volatility of renewable energy. An energy signal light was developed as an energy feedback device, which is integrated into the \ac{DEMS} in a living lab and allows individual configuration. In summary, the results presented should be compared with those of other research approaches in the future and require qualitative and quantitative evaluation.

Sustainable energy development (SED) is a crucial component of the Sustainable Development Goals (SDG), aiming to maintain economic and social progress while protecting the environment and mitigating climate change’s effects. SED serves as a transition paradigm for sustainable development, providing a blueprint for energy peace and prosperity for people and all uses. This article presents the history of SED and then uses a critical discourse approach to summarize existing review studies in SED. Ten interlinked themes of SED are identified, with two of them considered to be among the least studied in existing SED reviews and in the current global discussion around climate change. This study explores these two themes, which include energy financing and the need for 100% renewable energy (RE), a sub-theme of decarbonization strategy working towards the 1.5–2.0 °C scenario. The study suggests that the current G20 countries’ contributions, if maintained continuously per annum, in addition to 80% more funding from private investment compared to the amount in the 1.5 °C scenario financial requirements for clean energy, are sufficient to limit global warming. In addition to the present drive for 100% RE, the article also discusses emerging issues, such as energy storage options with an indication of hydrogen as the most promising, other energy-related development agendas, and the need for regional security stability to prevent energy wars. Selected SED decarbonization strategies are presented across the power, transport, building, and industrial sectors. The study concludes with progress and directions for future research, mainly the need for re-defining nationally determined contribution (NDC) through an emissions budgeting and centralized global or regional emissions stock-taking strategy working towards the 1.5 °C scenario.

Conventional methods of climate change (CC) mitigation have not ‘bent the curve’ of steadily rising annual anthropic CO2 emissions or atmospheric concentrations of greenhouse gases. This study reviews the present position and likely future of such methods, using recently published literature with a global context. It particularly looks at how fast they could be implemented, given that the limited time available for avoiding catastrophic CC (CCC). The study then examines solar geoengineering, an approach often viewed as complementary to conventional mitigation. The review next introduces equity considerations, and shows how this will shorten even further the time available for effective action for CC mitigation. The main findings are as follows. Conventional mitigation approaches will be implemented too slowly to be of much help in avoiding CCC, partly because some suggested technologies are infeasible, while others are either of limited technical potential, or, like wind and solar energy, cannot be introduced fast enough. Because of these problems, solar geoengineering is increasingly advocated as a quick-acting and effective solution. However, it could have serious side effects, and given that there will be winners and losers at the international as well as the more regional level, political opposition may make it difficult to implement. The conclusion is that global energy consumption itself must be rapidly reduced to avoid catastrophic climate change.

Background: Mitigating climate change requires fundamentally redesigned energy systems in which renewable energy sources ultimately replace fossil fuels such as natural gas. In this context, the question how and to which extent the gas sector can contribute to an increasingly climate-neutral future EU energy system is heavily debated among scholars, energy industry experts and policy makers. Methods: We take a two-step approach: We begin with a review of studies from energy industry and academia to discuss potential gas sector contributions from a holistic energy system design point of view; this is followed by a comprehensive discussion of technical potentials, micro-economic conditions and societal implications of renewable gas. We then enrich our findings with the results of an empirical focus group process. Results: The gas sector can not only contribute to balancing volatile renewable energy production but also enable the supply of renewable energy to end-users in gaseous form; based on existing infrastructure. This could reduce costs for society, increase public acceptance and ultimately speed up the energy system transformation. There is the theoretical technical potential to substitute major parts of natural gas with renewable gas of biogenic and synthetic nature. This, however, crucially requires a supportive policy framework like the one established for renewable electricity. Conclusion: Given the societal benefits and the competitiveness of renewable gas as compared to renewable alternatives, energy policy makers should incorporate renewable gas and the existing gas infrastructure in the future energy system framework. The objective should be an optimized interplay of various energy vectors and their infrastructure along the entire energy supply chain. This requires a level playing field for different renewable technologies across different policy areas and a form of public support that strikes the balance between facilitating the gradual substitution of natural gas by renewable gas while maintaining public acceptance for this transformation despite higher costs for end-users.: Given the societal benefits and the competitiveness of renewable gas as compared to renewable alternatives, energy policy makers should incorporate renewable gas and the existing gas infrastructure in the future energy system framework. The objective should be an optimized interplay of various energy vectors and their infrastructure along the entire energy supply chain. This requires a level playing field for different renewable technologies across different policy areas and a form of public support that strikes the balance between facilitating the gradual substitution of natural gas by renewable gas while maintaining public acceptance for this transformation despite higher costs for end-users.

Traditional high pressure mechanical compressors account for over half of the car station’s cost, have insufficient reliability and are not feasible for a large-scale fuel cell market. An alternative technology, employing a two-stage, hybrid system based on electrochemical and metal hydride compression technologies, represents an excellent alternative to conventional compressors. The high-pressure stage, operating at 100-875 bar, is based on a metal hydride thermal system. A techno-economic analysis of the metal hydride system is presented and discussed. A model of the metal hydride system was developed, integrating a lumped parameter mass and energy balance model with an economic model. A novel metal hydride heat exchanger configuration is also presented, based on mini-channel heat transfer systems, allowing for effective high-pressure compression. Several metal hydrides were analyzed and screened, demonstrating that one selected material, namely (Ti_0.97Zr_0.03)_1.1Cr_1.6Mn_0.4, is likely the best candidate material to be employed for high-pressure compressors under the specific conditions. System efficiency and costs were assessed based on the properties of currently available materials at industrial levels. Results show that the system can reach pressures on the order of 875 bar with thermal power provided at approximately 150 °C. The system cost is comparable with the current mechanical compressors and can be reduced in several ways as discussed in the paper.

Building integrated photovoltaics (BIPV) consists of PV panels that are integrated into the building as part of the construction. This technology has advantages such as the production of electricity without necessary additional land area. This paper provides a literature review about the recent developments in urban building energy modelling, including tools and methods, and how they can be used to predict the effect of PV systems on building outdoor and indoor environments. It is also intended to provide a critical analysis on how PV systems affect the urban environment, both from an energy and a comfort point of view. The microclimate, namelly the urban heat island concept, is introduced and related with the existence of PV systems. It is concluded that urban building energy modelling (UBEM) can be effective to study the performance of PV systems in the urban environment. It allows to simultaneously predict the building energy performance and the microclimate effect. However, there is a need to develop new methodologies to overcome the challenges associated to UBEM, especially in what concerns non-geometric data, which leads to a major source of errors. and to find an effective method to predict the effect of PV systems in the urban environment.

Enhancing energy efficiency within the building sector is imperative to curbing energy losses, given that this sector alone contributes to over 34% of global energy consumption. Employing a building management system, along with its regular updates, presents a strategic avenue to decrease energy usage, enhance building energy efficiency, and more. Tailored control strategies, aligned with the unique characteristics and usage patterns of each building, are essential for achieving energy savings. This article presents an evaluation of HVAC system efficiency in office buildings, utilizing a data-driven approach coupled with simulations conducted in IDA ICE software. The research explores the control strategy of an office building equipped with a constant air volume HVAC system, featuring a regularly controlled air handling unit. The objective is to boost energy efficiency while striking a balance between occupant comfort and energy consumption. Findings indicate that by analyzing measured data and adjusting configurable parameters, building energy consumption can be significantly reduced. Close monitoring of indoor parameters by building operators and corresponding adjustments to the HVAC system can yield energy savings of up to 16%. Leveraging these insights, the paper suggests integrating data-driven and dynamic simulation methods into building management system models to optimize HVAC systems, enhance energy efficiency, and advance ambitious carbon neutrality objectives.

Geoenvironmental engineering involves defining solutions for complex problems, such as containment systems management, contaminant transport control, wastewater management, remediation of contaminated sites and valorization of geomaterials and wastes. In the last years, energy harvesting (EH) - or energy scavenging - methods and technologies have been developed to reduce the dependence on traditional energy sources, namely fossil fuels, and nuclear power, also responding to the increase of energy demands for human activities and to fulfill sustainable development goals. EH in geoenvironmental works and surrounding soil and water environment include a set of processes for capturing and accumulating energy from several sources considered deemed wasted or unusable associated to soil dynamics, stress and strain of geomaterials, hydraulic, vibrations, biochemical, light, heating and wind sources can be potential EH systems. Therefore, this work presents a review of the literature and critical analysis on the main opportunities for EH capturing, accumulating and use in geoenvironmental works, among basic electric concepts and mechanisms, analyzing those works in complex conditions involving biological, chemical, mechanical, hydraulic, and thermal coupled actions, concluding with the main investigation and challenges within geoenvironmental aspects for EH purpose.

In this paper, spacetime is defined as the absolutely invariant homogeneous "coordinate spacetime" frame and its modulation by the relatively variable non-homogeneous "metric spacetime" under its constraints. This modulation is caused by matter and motion, and carries the function of transmitting interactions, reflecting the diffeomorphism invariance and Lorentz invariance. This inhomogeneous spacetime concept makes the medium nature of spacetime more obvious and avoids the problem of "path dependence" caused by the concept of curved spacetime. In this paper, it is argued that all energy-momentum has internal spatio-temporal properties, and all interactions must be transmitted through spacetime metrics. On this basis, a converging and dispersing cyclic multiverse model is proposed. This model of the universe is inevitable as long as there are two macroscopic manifestations of the matter of the universe, namely, gravitation induced convergence and "explosive" dispersion caused by different factors. The new cosmic model matches the observed accelerated "expansion" of the universe and no longer requires the dark energy hypothesis.

The benchmarking of hotel energy use comprehensively identifies the controllable and uncontrollable factors affecting energy performance, including building characteristics, management strategies, operations, and maintenance systems. Other factors include climatic conditions, floor areas, operating hours, occupancy rates, and guest populations. A benchmarking study on energy consumption patterns in significant hotels (each with less than 100 rooms and an average staff strength of 40 employees), situated in the university town of Nsukka (longitude 70 23' E, latitude 60 52' N), Nigeria, was performed using the data envelopment analysis (DEA) methodology. DEA, a linear programming technique that measures the relative performances of units, was chosen as a benchmarking methodology due to its ability to handle multiple inputs and outputs. Following a correlation test, energy use intensity, diesel consumption, and the number of employees were selected as the analysis inputs, while the occupancy rate was chosen as the output variable. Data on these variables spanning 12 months were collected using questionnaires, interviews, site visits, and oral conversations with hotel managers to ensure validity. Grid-supplied electricity accounted for most of the hotels' energy needs, followed by diesel used in generators. More than 70% of the electricity use was for HVAC. From the DEA, Hotel 3 (DMU H3) had a technical efficiency score of 1, whereas adjustments were recommended for improving the efficiency scores of the other hotels, which were deemed inefficient. DMU H7 had the lowest efficiency score (0.474) and the highest identified savings for electricity and diesel. The analysis also revealed that occupancy rates were generally low in the months of June and July, coinciding with the high rainfall season with its accompanying decline in outdoor activities. Consistent with this, electricity consumption was highest in the Christmas and Easter holiday months of December, January, and April following increased travel-related activities.

Using a wide range of organic substrates in the methane fermentation process enables efficient biogas production. Nonetheless, in many cases, the efficiency of electricity generation in biogas plant cogeneration systems is much lower than expected, close to the calorific value of the applied feedstock. This paper analyses energy conversion efficiency in a 1 MWel agricultural biogas plant fed with corn silage or vegetable waste and pig slurry as a feedstock dilution agent, depending on the season and availability. Biomass conversion studies were carried out for 12 months, during which substrate samples were taken once a month. The total primary energy in substrates was estimated in laboratory conditions by measuring the heat of combustion in a ballistic bomb calorimeter (17,760 MWh·year-1), and in the case of pig slurry, biochemical methane potential (BMP, (201.88±3.21 m3·Mg VS-1). Further, the substrates were analysed in terms of their chemical composition — from protein, sugar and fat content to mineral matter determination, among other things. The results obtained during the study were averaged. Based on such things as the amount of biogas produced at the plant, the amount of chemical (secondary) energy contained in methane as a product of biomass conversion (10,633 MWh·year-1) was calculated. Considering the results obtained from the analyses, as well as the calculated values of the relevant parameters, biomass conversion efficiency was determined as a ratio of chemical energy in methane to (primary) energy in substrates, which was 59.87%, as well as electricity production efficiency, as a ratio of electricity produced (4,913 MWh·year-1) to primary energy, with a 35% cogeneration system efficiency. Full energy conversion efficiency, related to electricity production, reached a low value of 27.66%. This article provides an insightful, unique analysis of energy conversion in an active biogas plant as an open thermodynamic system.

Wireless energy harvesting (EH) communication has long been considered a sustainable networking solution. However, it has been limited in efficiency, which has been a major obstacle. Recently, strategies such as energy relaying and borrowing have been explored to overcome these difficulties and provide long-range wireless sensor connectivity. In this article, we examine the reliability of the wireless-powered communication network by maximizing the net bit rate. To accomplish our goal, we focus on enhancing the performance of hybrid access points and information sources by optimizing their transmit power. Additionally, we aim to maximize the use of harvested energy by energy-harvesting relays for both information transmission and energy relaying. However, this optimization problem is complex as it involves non-convex variables and requires combinatorial relay selection indicators optimization for decode and forward (DF) relaying. To simplify this problem, we utilize the Markov decision process and deep reinforcement learning framework based on the deep deterministic policy gradient algorithm. This approach enables us to tackle this non-tractable problem, which conventional convex optimisation techniques would be difficult to solve in complex problem environments. The proposed algorithm significantly improves the end-to-end net bit rate of the smart energy borrowing and relaying EH system by 13.22%,27.57%, and 14.12% compared to the benchmark algorithm based on borrowing energy with an adaptive reward for Quadrature Phase Shift Keying, 8-PSK, and 16-Quadrature amplitude modulation schemes, respectively.

Increasing of renewable energy share in total energy production is a direction that leads towards European Union’s aims of carbon neutrality by 2050, as well as increases energy self-sufficiency and independence. Some of the main challenges to increase renewable energy share while providing efficient and secure energy supply are related to optimization and profitability of de-centralized energy production systems. Integration of energy storage systems in addition to decentralized renewable energy production, for example, by solar panels, leads to more effective electricity supply and smart energy solutions. The modelling of such complex dynamic system can be performed using system dynamics method. The aim of the article is to forecast the practice of electricity storage in Latvia in the coming decades. A system dynamics model predicting the implementation of battery storage in private households was created for the case study of Latvia. Modelling results reveal that under the right conditions for electricity price, investment costs and with the right policy interventions battery storage technologies combined with PV panels have high potential for utilization in household sector. Model results show that in baseline scenario with no additional policies up 21 422 households or 10.8 % of Latvian households could have combined PV and battery system installed in 2050. Moderate subsidy policy can help to increase this number up to 25 118.

The optimization of the energy grid is a critical task for ensuring a sustainable and efficient energy future. Deep machine learning techniques have the potential to improve energy grid optimization by predicting energy demands and supplies, optimizing energy production and distribution, and detecting and preventing fraud. However, there are also several challenges associated with the use of deep machine learning in energy grid optimization. These include the lack of standardized datasets and data quality issues, interpretability and explain-ability of machine learning models, ethical and social implications of using machine learning, and integration with existing energy infrastructure and regulatory frameworks. Having a clear understanding that continued research and developments in deep learning applications to energy field are crucial for achieving a sustainable and efficient energy future. This paper therefore reviewed existing literature for challenges and opportunities associated with deep machine learning in energy grid optimization; and highlights the importance of continued research and development in the field. The paper found out that opportunities for future research in deep machine learning for energy grid optimization include advancements in machine learning algorithms and techniques, development of new datasets and data collection methods, integration of machine learning with other emerging technologies. It also established needs for collaborative research and public-private partnerships.

We use a recently proposed formulation of quantum mechanics based, not on potential functions but rather, on orthogonal energy polynomials. In this context, the most important building block of a quantum mechanical system, which is the wavefunction at a given energy, is expressed as pointwise convergent series of square integrable functions in configuration space. The expansion coefficients of the series are orthogonal polynomials in the energy; they contain all physical information about the system. No reference is made at all to the usual potential function. We consider, in this new formulation, few representative problems at the level of undergraduate students who took at least two courses in quantum mechanics and are familiar with the basics of orthogonal polynomials. The objective is to demonstrate the viability of this formulation of quantum mechanics and its power in generating rich energy spectra illustrating the physical significance of these energy polynomials in the description of a quantum system. To assist students, partial solutions are given in an appendix as tables and figures.

Considering the actual world economical trends, one of the most important questions is now and in the future: how to reduce power consumption of electronic systems. Since the invention of computers, the electrical energy consumption step by step increased. Now when not only computers, but electric vehicles, robots, automation, and unmanned aerial vehicles play a very important role of our life, the main problem of system designers is how to reduce energy consumption in these systems. But also the existing already working systems must be revised in order to decrease their electric power consumption. The importance of this subject (energy control) shows that a huge number of research publications and survey papers deal with it. Just focusing on the last one or two years (2021 and 2022) the search hit 221000 titles (103000 hits only in 2022). Analyzing all the research areas is almost impossible, but focusing on some important research subjects, where one of the main topic is “energy saving methods” can give an overview about the subject. The paper focuses on the area of industrial robotic systems, electric vehicles, and embedded systems.

It is a truism that whole energy system models underpin the development of policies for energy system decarbonisation. But recent reviews have thrown doubt on the appropriateness of such models for addressing the multiple goals for future energy systems, in the face of emergent real-world complexity and the evolution of stakeholder’s priorities. Without an understanding of the changing priorities of policy makers and expectations of stakeholders for future systems, system objectives and constraints are likely to be ill-defined, and there is a risk that models may be inadvertently instrumentalised. Adopting a system architecture perspective, the authors have undertaken a three-year programme of research to explore strategies for decarbonising heat in the UK, with interaction with and elicitation of needs from stakeholders at its heart. This paper presents the procedure, methods, and results of an exercise in which experts from stakeholder organisations across the energy system were interviewed. Analysis of interview data reveals two broad approaches to heat decarbonisation which can be broadly defined as either adaptive or transformative. Specific insights gained from these interviews enabled our modelling teams to refocus their work for exploration with a wider circle of stakeholders. Results suggests that this iterative approach to formalising model-policy interaction could improve the transparency and legitimacy of modelling and enhance its impact on policy making.

Law of conservation of energy is the most well-established law of modern physics. But, inflationary cosmological model which assumes the universe to be created from a point of singularity has not been able to identify the source of energy for creation of this universe. As per uncertainty principle, a quantum vacuum fluctuation can at most create energy of ~10^-8 kg in a Planck time of ~5.4 ×10^-44 s whereas total positive energy due to matter/vacuum existing in the universe is more than ~10⁵⁴ kg. To solve this problem, we have recently published a new cosmological model (Biswaranjan Dikshit, Canadian Journal of Physics, 100, 218-225, [2022]) in which we have mathematically proved that the total energy of the universe can be zero right from the beginning of the universe to till date due to negative gravitational potential energy and thus law of conservation of energy can be satisfied during creation of the universe from nothing. In this article, starting from a simple argument, we explain why net energy of the universe can be zero only in our model, not in standard cosmological model. An interesting fact pointed out in this paper is that the factor ~10⁶² by which radius of universe has increased from its starting value of ~10^-36 m to present value of ~10²⁶ m is same as the factor by which positive energy has increased from Planck energy ~10^-8 kg to present value ~10⁵⁴ kg. This is in agreement with our new model that predicts the positive energy of universe to be proportional to the radius of universe. We also bring out to the notice that zero energy universe is possible only if smallest possible length in nature is, l_min=l_p(π/2)^1/2 = 2.0×10^-35 m. Minimum possible length is important in theory of quantum gravity and string theory.

Intending to analyze the role of nuclear power in an integrated energy system, we used the IESA-Opt-N cost minimization model focusing on four key themes: system-wide impacts of nuclear power, uncertain technological costs, flexible generation, and cross-border electricity trade. We demonstrate that the Levelized Cost of Energy (LCOE) alone should not be used to demonstrate the economic feasibility of a power generation technology. For instance, under the default techno-economic assumptions, particularly the 5% discount rate and exogenous electricity trade potentials, it is cost-optimal for the Netherlands to invest in 9.6 GWe nuclear capacity by 2050. However, its LCOE is 34 €/MWh higher than offshore wind. Moreover, we found that nuclear power investments can reduce demand for variable renewable energy sources in the short term and higher energy independence (i.e., lower imports of natural gas, biomass, and electricity) in the long term. Furthermore, investing in nuclear power can reduce the mitigation costs of the Dutch energy system by 1.6% and 6.2% in 2040 and 2050, and 25% lower national CO₂ prices by 2050. However, this cost reduction is not significant given the odds of higher nuclear financing costs and longer construction times. In addition, this study has shown that lower financing costs (e.g., EU taxonomy support) considerably reduce the relevance of nuclear cost uncertainties on its investments. Furthermore, we demonstrate that the economic feasibility of national nuclear power investments can vary considerably depending on the cross-border electricity trade assumptions. Additionally, we found that lowering the cost of small modular reactors has more impact on their economic feasibility than increasing their generation flexibility. In conclusion, under the specific assumptions of this study, nuclear power can play a complementary role (in parallel to the wind and solar power) in supporting the Dutch energy transition from the sole techno-economic point of view.

Airborne wind energy (AWE) systems use tethered flying devices to harvest higher-altitude winds to produce electricity. For a successful deployment of these systems, it is crucial to understand how the public perceives them. If public concerns about the technology are not taken seriously, implementation could be delayed or, in some cases, prevented, resulting in increased costs for project developers and a lower contribution of the sector to renewable energy targets. This literature review assessed the current state of knowledge on public responses to AWE. An exhaustive literature search led to the identification of 40 relevant publications that were reviewed. The literature assumed that the safety, visibility, acoustic emissions, ecological impacts, and the siting of AWE systems shape public responses to the technology. The reviewed literature views people’s responses to AWE very optimistically but lacks scientific evidence to back up its claims. It seems to overlook that the influence of AWE’s characteristics (e.g., visibility) on public responses will also depend on a range of situational and psychological factors (e.g., people’s general attitude towards AWE, the public’s trust in project developers). Therefore, empirical social scientific research is needed to increase the field’s understanding of public responses to AWE and thereby facilitate deployment.

Integration of battery energy storage in photovoltaic (PV) systems can reduce the electricity costs and provide desirable flexibility and reliability to these systems decreasing renewable energy fluctuations. This paper presents a review of the PV-battery application in Brazil, highlighting the challenges and prospects based on the state-of-art. A PV-battery systems description is presented in this work, as well as the most applied battery technology and its comparison. The paper also describes the set of applications such as voltage and frequency regulation, renewable energy integration, power quality, etc. In the Brazilian scenario, there are applications of PV-battery systems, most of them part of research and development projects (R&D’s), and some real cases are shown, including its goals, applied equipment, operation modes, strategies, and perspectives. Additionally, this work evaluates the Brazilian scenario regarding the energy storage systems implementation challenges, such as regulatory barriers, business models, and opportunities for R&D in the energy market. In conclusion, it is need develop proper regulatory models to expand PV-battery systems and make them visible to the agents in the electricity sector.

Information and communication technologies (ICT) are increasingly permeating our daily life and we ever more commit our data to the cloud. Events like the COVID-19 pandemic put an exceptional burden upon ICT infrastructures. This involves increasing implementation and use of data centers, which increased energy use and environmental impact. The scope of this work is to take stock on data center impact, opportunities, and assessment. First, we estimate impact entity. Then, we review strategies for efficiency and energy conservation in data centers. Energy use pertain to power distribution, IT-equipment, and non-IT equipment (e.g. cooling): Existing and prospected strategies and initiatives in these sectors are identified. Among key elements are innovative cooling techniques, natural resources, automation, low-power electronics, and equipment with extended thermal limits. Research perspectives are identified and estimates of improvement opportunities are presented. Finally, we present an overview on existing metrics, regulatory framework, and bodies concerned.

In light of the latest trends in global installed capacities, the importance of variable renewable energy sources (VRES) to future energy supply systems is evident. Despite this, the inherent intermittency of VRES remains an obstacle to their widespread adoption. Green hydrogen is often suggested as an energy carrier that can account for this in a sustainable manner. In the analysis, a robust European energy system in the context of 2050 and with 100% VRES energy supply is designed through an iterative minimal cost-optimization approach that ensures robust security of supply over 38 weather-year scenarios (1980-2017). The impact of spatial VRES variability is factored in by defining exclusive VRES groups within each optimization region and, from this, it can be seen that higher numbers of groups in each region offer cheap electricity generation locations to the optimizer and thus decrease the total annual cost of the system. Beyond this, the robust system design and impact of inter-annual variability is identified by iteratively combining the installed capacities of different system designs obtained by applying 38 historical weather years. The robust system design outlined here has significantly lower capacities in comparison to the maximum regional capacities obtained in the first round of optimization.

The rapid development of China's economy has led to a rapid increase in energy production and use. Among them, the excessive consumption of coal in fossil energy consumption is the leading cause of air pollution in China. This paper incorporates renewable energy innovation, fossil energy consumption and air pollution into a unified analysis framework, and uses spatial measurement models to investigate the spatial effects of renewable energy green innovation and fossil energy consumption on air pollution in China, and decomposes the total impact into direct and indirect effects. influences. The empirical results show that China's air pollution, renewable energy green innovation and fossil energy consumption are extremely uneven in geographical space, generally showing the characteristics of high in the east and low in the west, and showing a strong spatial aggregation phenomenon. Fossil energy consumption will lead to increased air pollution, and the replacement of fossil fuels with clean and renewable energy is an important means of controlling pollution emissions. The direct and indirect effects of renewable energy green innovation on air pollution are significantly negative, indicating that renewable energy green innovation not only suppresses local air pollution, but also suppresses air pollution in neighboring areas. The consumption of fossil energy will significantly increase the local air pollution, and the impact on the SO2 and Dust&Smoke pollution in the adjacent area is not very obvious. It is recommended to strengthen investment in renewable energy green innovation, reduce the proportion of traditional fossil energy consumption, and pay attention to the spatial connection and spillover of renewable energy green innovation.

The stability between the limited available energy resources and their consumption is an important concern of the modern world. The study deals with the development of the methods for measuring the energy performance of different renewable and non-renewable resources used for electricity generation with the help of an energy performance indicator called the Primary Energy Factor (PEF). This study takes account of all energy stages from the resources extraction to its transportation, conversion, combustion and then finally to utilization. The study conducted a comparative approach to calculate the PEF values of electricity generated in South Korea from the period of 1980 to 2017. Four different methodologies namely Eurostat methodology, Life cycle methodology, Modified Eurostat methodology, and upper-end methodology have been used. A set of Programs has been written in MATLAB to calculate the i. PEF values of electricity generated. ii. Impact of different renewable and non-renewable energy sources on PEF values. iii. Future trend of PEF values of electricity in South Korea At the national and local level, this study will help the government and other law-making institutions to make policies regarding annual purchase consumptions of energies by different industrial, residential, public and transportation sectors and at the Global level, the implementation of this study will be the catastrophe of maintaining the stability between the available energy resources, and consumptions. This, in turn, will lead to suitable living conditions for future generations

Renewable energy sources (RES) will play a crucial role in future sustainable energy systems. In scenarios analyzing future energy system designs, a detailed spatial and temporal representation of renewable-based electricity generation is essential. For this, sufficiently representative weather data are required. Most analyses performed in this context use the historical data of either one specific reference year or an aggregation of multiple years. In contrast, this study analyzes the impact of different weather years based on historical weather data from 1980 through 2015 in accordance with the design of an exemplary future energy system. This exemplary energy system consists of on- and offshore wind energy for power-to-hydrogen via electrolysis, including hydrogen pipeline transport for most southwestern European countries. The assumed hydrogen demand for transportation needs represents a hypothetical future market penetration for fuel cell-electric vehicles of 75%. An optimization framework is used in order to evaluate the resulting system design with the objective function of minimizing the total annual cost (TAC) of the system. For each historical weather year, the applied optimization model determines the required capacities and operation of wind power plants, electrolyzers, storage technologies and hydrogen pipelines to meet the assumed future hydrogen demand in a highly spatially- and temporally-detailed manner, as well as the TAC of the system. Following that, the results of every individual year are compared in terms of installed capacities, overall electricity generation and connection to the transmission network, as well as the cost of these components within each region. The results reveal how sensitive the final design of the exemplary system is to the choice of the weather year. For example, the TAC of the system changes by up to 20% across two consecutive weather years. Furthermore, significant variation in the optimization results regarding installed capacities per region with respect to the choice of weather years can be observed.

Energy taxation is used globally as a means of energy policy. Energy tax plays an important role as a driving force for the conversion to environmentally friendly energy. The basic tax principles considered in the design of energy taxation increases the efficiency of policy instruments. The purpose of this study is to evaluate South Korea’s energy taxation based on tax principles, namely, equity, efficiency, simplicity, flexibility, and accountability and suggest directions for improvement. This study applied a methodology that provides policy implications, such as reviewing existing literature and comparing energy taxes. Results of this study show that South Korea’s energy taxation is negative in terms of equity, simplicity, and accountability. South Korea’s current energy tax is regressive to income classes and complex tax structures and it does not objectively measure the impact of energy taxation. However, energy taxation is evaluated positively in terms of efficiency and flexibility because it meets the greenhouse gas reduction policy and operates a flexible tax rate. The results of this analysis provide policy implications for reorganizing South Korea’s energy taxation.

In Electrified Vehicles, the cost, efficiency, and durability of electrified vehicles are dependent on the energy storage system (ESS) components, configuration and its performance. This paper, pursuing a minimal size tactic, describes a methodology for quantitatively and qualitatively investigating the impacts of a full bandwidth load on the ESS in the HEV. However, the methodology can be extended to other electrified vehicles. The full bandwidth load, up to the operating frequency of the electric motor drive (20 kHz), is empirically measured which includes a frequency range beyond the usually covered frequency range by published standard drive cycles (up to 0.5 Hz). The higher frequency band is shown to be more efficiently covered by a Hybrid Energy Storage System (HESS) which in this paper is defined as combination of a high energy density battery, an Ultra-Capacitor (UC), an electrolytic capacitor, and a film capacitor. In this paper, the harmonic and dc currents and voltages are measured through two precision methods and then the results are used to discuss about overall HEV efficiency and durability. More importantly, the impact of the addition of high-band energy storage devices in reduction of power loss during transient events is disclosed through precision measurement based methodology.

Climate change and global warming are becoming important problems around the globe. To prevent these environmental problems, many countries try to reduce the emissions of greenhouse gases (GHG) and manage the consumption of energy. In Korea, Korea Electric Power Corporation (KEPCO) has introduced Smart Grid (SG) technologies to its branch office in 2014. This was the first demonstration of smart grid on a building called Smart Grid Station. This paper treats the achievements of the Smart Grid Station (SGS) by its early target in three aspects. The things are peak reduction, power consumption reduction and electricity fee saving. The authors analyzed the achievements by comparing the data of 2015 with the data of 2014. Through the evaluation, the authors studied the case, proved the advantages of SGS, and suggested the requirements to improve and the direction to go of the system.

In this paper, we propose a simple tool to help the energy management of a large buildings stock defining clusters of buildings with the same function, setting alert thresholds for each cluster, and easily recognizing outliers. The objective is to enable a building management system to be used for detection of abnormal energy use. First, we framed the issue of energy performance indicators, and how they feed into data visualization (Data Viz) tools for a large building stock, especially for university campuses. Both for Data Viz and clustering algorithm processes, we discussed two possible approaches to choose the right number of clusters and the identification of alert thresholds and outliers, after a brief presentation of the University of Turin's building stock case study. Different Data Viz tools have been studied to apply a specific clustering algorithm, the k-means one. An explorative analysis based on the general Multidimensional detective approach by Inselberg has been performed. Two multidimensional analysis tools, the Scatter Plot Matrix and the Parallel coordinates method have been used. Secondly, the k-means clustering algorithm has been applied on the same dataset in order to test the hypothesis made during the explorative analysis. Data Viz techniques developed in this study revealed to be very useful to explore quickly and simply a large buildings' stock, identifying the worst efficient buildings and clustering them according to their distinct functions.

Rural electrification in remote areas of developing countries has several challenges which hinders energy access to the population. For instance the extension of the national grid to provide electricity in these areas is largely not viable. The Kenyan government has put a target to achieve universal energy access by the year 2020. In order to realize this objective, focus is being shifted to establishing off-grid power stations in rural areas.Among rural areas to be electrified, Habaswein is a settlement in Kenya's North Eastern region without connection to the National Power Grid where Kenya Power installed a stand alone hybrid mini-grid.Based on field observations, power generation data analysis, evaluation of the potential energy resource and simulations, this research intends to evaluate the performance of the Habaswein mini-grid and optimize the existing hybrid generation system to enhance its reliability and reduce the operation costs.The result will be a suggestion of how Kenyan rural areas could be sustainably electrified by using renewable energy based off-grid power stations. It will contribute to bridge the research gap currently existing on that area, and it will be a vital tool to researchers, implementers and the policy makers in energy sector.

Technology is in the way to reach in its climax but the basic understanding of science in many phenomena is still awaited even though the nature witnesses it. Scientific research reveals strong analogy between photon and electron. When an atom deals neutral state, it levitates electron of outer ring from the back surface while placing the bit-energy at front surface. Gravitation behavior of that electron starts at the centre of relaxation point by including the force of side pole where the pulling force of nearby unfilled state of that atom from the front surface results into depict forcing energy shape like Gaussian distribution symbol with both ends turned called unit photon. The inertia is being involved at each stage of changing direction of that electron by introducing the disappearances of forces of two poles against the appearances of forces of two opposite poles during rest to motion and motion to rest in the first half-cycle. The same is the case in the second half-cycle of that electron during rest to motion and motion to rest but it is under different introduction of the disappearances of forces against appearances of forces. However, at stage of levitating or gravitating period of electron, only one force is being involved at one time where the opposite force is disappeared. The uninterrupted confined inter-state electron-dynamics of atom under the availability of several bits of bit-energy results into generate forcing energy shape like a wave. Two bits of bit-energy where shape of bit for first half-cycle is like integral symbol and second half-cycle is like opposite integral symbol which are being placed along the configuring trajectory of inter-state electron-dynamics during forward-direction cycle and two bits of bit-energy shape in opposite order are being placed along the trajectory of inter-state electron-dynamics during back-direction cycle. Generating forcing energy of unit photon in each cycle is pushing to the rear side by remaining connected till the electron is not restoring the state of rest. Silicon atom is considered as a model system under neutral state. Uninterrupted confined inter-state electron-dynamics result into generate forcing energy that can travel immeasurable length and unavailability of necessitating bit-energy at any interrupted stage result into generate an overt photon. Inter-state electron-dynamics for at least two cycles generate an overt photon –a photon length twice to unit photon. Under certain interaction of unit photon, it divides equally into two bits of bit-energy instead of dividing into tits and bits of heat. The mechanism of generating photon characteristic current by the electron of neutral state atom validates that atoms are four-dimensional discs at centre of dealing no force. An isolated electron is being grounded under directed forcing energy to impinge a neutral state atom where the gained instantaneous velocity under merged energy resulting into distort atom at that point. Matter changes the role of energy and force under various sorts of interactions. Here, heat energy and photon energy explore matter at atomic and electron levels, thus, devise basis of science to describe.

Based on recent interest and on the importance of the ongoing climate change catastrophe, this article provides the basics of global carbon cycle modelling as required for the assessment of the degree of carbon neutrality of biomass energy, and its underlying dynamics. It is aimed at clari-fying the question “Are biomass fuels carbon neutral?”. The "Combined Energy and Biosphere Model" (CEBM) computes annual carbon flows including growth and decay of plants on 2.52.5° grid elements of the continents’ surface and offers detailed results on the changes of after implementation of large-scale biomass energy strategies world-wide. The main (and possibly unexpected) effect is the long-term depletion of the soil organic compartment after extraction of biomass fuels. When comparing CEBM model runs using (i) biomass energy sources and (ii) carbon-free energy sources (such as solar or wind), it becomes quantitatively clear already on the theoretical level (i.e., even without taking into account effi-ciency losses) that biomass is only “half as carbon neutral” as ideally assumed, to express a rule of thumb – mainly because of soil carbon depletion. Still, biomass energy will play an important role when fighting global warming, even if efforts to lower energy demand are preferable as a fundamental strategy.

In thermodynamic theory, free energy (i.e., available energy) is the concept facilitating the combined applications of the theory’s two fundamental laws, the first and the second laws of thermodynamics. The critical step was taken by Kelvin, then by Helmholtz and Gibbs— that in natural processes, free energy dissipates spontaneously. With the formulation of the second law of entropy growth, this may be referred to as the dissymmetry proposition manifested in the spontaneous increase of system/environment-entropy towards equilibrium. Because of Kelvin’s pre-entropy-law formulation of free energy, our concept of free energy is still defined, energy-centrally, as body’s internal energy or enthalpy, subtracted by energy that is not available within a framework on the premise of primacy of energy, in which free energy dissipates spontaneously and universally. This primacy of energy is called into question because the driving force to cause a system’s change is the purview of the second law. This paper makes a case for an engineering thermodynamics framework, instead, to be based on the premise of the primacy of dissymmetry over free energy. With Gibbsian thermodynamics undergirded with dissymmetry proposition and engineering thermodynamics with the dissymmetry premise, the two branches of thermodynamics are unified to become classical thermodynamics.

The author’s opinion is that the negative energy solutions of the Dirac equation mean that a particle can be of negative kinetic energy (NKE) besides positive kinetic energy (PKE). We think that NKE particles are dark ones and NKE matter is dark matter. In our previous works, the dark matter theory of the NKE version and the dark energy theory that matched dark matter theory were put forth. In this work, we investigate the topics related to the metamorphosis of objects between PKE and NKE. We first evaluate the collosions between a PKE and a NKE particles. A scenario of accelerating PKE particles is raised. We put forth the cosmic dark radiation background and gravity potential background. In the universe, negative energy is predominating. In the observable universe, substances constitute stable PKE systems. The total energy of every such system is negative. We propose a mechanism that NKE substances combine into stable PKE systems. Macroscopically, NKE objects can constitute stable PKE astrophysical systems by means of gravity between them. Microscopically, NKE particles can combine into stable PKE systems by means of attractive interactions between them, say, Coulomb attraction. Currently, people think that there are four ingrediants in the universe: photons \Omega_R0, matter \Omega_M0, dark matter \Omega_DM, and dark energy \Omega_\lambda0. We analyze the order of the appearance of the four ingredients and conclude that qualitatively, their proportions should be \Omega_\lambda0 > \Omega_DM > \Omega_M0 > \Omega_R0.

We live in the world that is completely entangled on energy and thus, Humankind can no longer do without it, power. With electricity being the main form of energy today, this has increased the complexity of our life today. In Uganda, electricity generation is mainly through hydropower which put the country in the bottleneck of over dependence on one source of energy. Yet, there are many energy systems out there that country can diversify its electricity generation. Therefore, the need to understand, the level of development and utilization of various energy systems has been the underlying question for this present study. Comprehensive literature survey was conducted from the electronic databases including ScienceDirect, Wiley, Sage, Scopus, Taylor & Francis, and Google Scholar. The publications in form of reports, conference papers, working papers, discussion papers, journal articles, book sections and textbooks were considered in this study. In total, 11 energy systems including human and animal energy, solid biomass (firewood), hydropower, wind, geothermal, solar, nuclear, peat, coal, petroleum, and non-solid biomass (methanol, hydrogen, ethanol, biodiesel, and biogas) are described. The current and the future development and utilization of these energy systems has been described. The challenges with their development and utilization were elaborated and the solution the challenges were presented. The hydropower with River Nile being the main river for large hydropower plant construction is the dominance energy system in Uganda. Nuclear energy will be the salvation for the country’s electric energy supply in the near future. Therefore, Uganda needs to bet big on nuclear energy.

Considering increasingly ambitious pledges by countries, pressure from society, investors, and clients further up the supply chain, the question for companies is not so much whether to take decarbonisation action, but what action and by when. However, determining an ideal mix of measures to apply ‘decarbonisation efficiency’ requires more than knowledge of technically feasible measures and how to combine them to achieve the most economic outcome: In this paper, the author describes seven aspects which heavily influence the composition of an ‘ideal mix’ that executive leadership needs to take a (strategic) position on. These aspects consider underlying motivations and span across (socio-)economic, technical, regulatory, strategic, corporate culture and environmental factors and further underline the necessity of clarity of definitions. How these decisions influence the determination of the decarbonisation-efficient ideal mix of measures, both in principle but also in terms of specific impact is further explored by providing examples. What choices are taken by German manufacturers in several of the aspects is disclosed by insights from about 850 responses to the ‘Energy Efficiency Index of German Industry’. Knowledge of the status quo, and clarity in definitions, objectives, time frames and scope are key.

Wave energy converter (WEC) arrays deployed in coastal regions may create physical disturbances potentially resulting in environmental stresses. Presently, limited information is available on the nature of these physical disturbance or the resultant effects. A quantitative Spatial Environmental Assessment Tool (SEAT) for evaluating potential effects of wave energy converter (WEC) arrays on nearshore hydrodynamics and sediment transport is presented for the central Oregon coast (USA) through coupled numerical model simulations of an array of WECs. Derived climatological wave conditions were used as inputs to the model to allow for the calculation of risk metrics associated with various hydrodynamic and sediment transport variables such as maximum shear stress, bottom velocity, and change in bed elevation. The risk maps provided simple, quantitative, and spatially-resolved means of evaluating physical changes in the vicinity of a hypothetical WEC array in response to varying wave conditions. Near-field risk of sediment mobility was determined to be moderate in the lee of the densely spaced array, where the potential for increased sediment deposition could result in benthic habitat alteration. Modifications to the nearshore sediment deposition and erosion patterns were observed near headlands and topographic features, which could have implications for littoral sediment transport. The results illustrate the benefits of a risk evaluation tool for facilitating coastal resource management at early market marine renewable energy sites.

This study explores the effects of tempering on the precipitation behavior and impact toughness of high-nickel steel. The specimens underwent double quenching at 870°C and 770°C, followed by tempering at various temperatures. Advanced characterization techniques including optical microscopy (OM), scanning electron microscopy (SEM), and transmission electron microscopy (TEM) were used to elucidate precipitation phenomena. Additionally, electron backscatter diffraction (EBSD) was employed to assess the misorientation distribution after tempering. Charpy impact tests were performed on specimens tempered at different temperatures to evaluate their toughness. The findings reveal that with increasing tempering temperature, the fraction of low-angle grain boundaries decreases, which correlates positively with enhanced impact toughness. The impact toughness peaks at 580°C and then diminishes with further temperature increases.

Succinate is proposed to be a mediator of muscle exercise-induced adaptations. We studied metabolic health and changes of muscle mass in 6-month-old male mice after 12 weeks of feeding regular diet (RD, 13.4 kcal% fat, 66.8 kcal% carbohydrate, 29.8 kcal% protein), high fat diet (HFD, 60 kcal% fat, 20 kcal% carbohydrates, 20 kcal% protein) and ketogenic diet (KD, 80 kcal% fat, <1 kcal% carbohydrates, 20 kcal% protein) with or without 2% succinate supplements (SUS) in drinking water (n=8-12 per group). Functional overloading of the plantaris muscle (PL) was induced in a group of mice by denervation of the gastrocnemius and soleus muscles at week 6 of feeding different diets. HFD induced the greatest (p < 0.001) increase in body and fat mass. HFD and KD lead to significant (p < 0.01) impairment in glucose tolerance compared to RD. SUS blunted (p < 0.01) initial surge in energy intake when mice were switched from RD to HFD, but did not influence any measures of metabolic health after 12 weeks of the study. Functional overloading lead to ~25% increase in PL mass which was not affected by diet or SUS. In conclusion, SUS does not have a long-term effect on metabolic health or muscle mass.

Gestational Diabetes Mellitus (GDMs) is worldly wide pregnancy complication. Gestational Diabetes can significantly impact the fetus development. However, the effects of high glucose on embryological development post-fertilization are yet to be researched. Danio rerio embryos are great model to study the embryonic development. In this study, the effects on embryological (morphological and genetic) development were examined in the presence of a high glucose environment that mimic the developing fetus in pregnant women with GMD. Fertilized Zebrafish embryos were treated with normal media and high glucose for 5 days from 3 hours post-fertilization(hpf) to 96hpf respectively as control and experimental groups. Morphological changes are recorded with Microscope images. Hatch rate and heart rate are compared between groups in set up time points. RNA-Seq is performed to examine the gene changes in experimental group. Glucose delayed the zebrafish embryo development by slowing the hatch rate about 24 hours. The brain, heart, and tail started showing morphology smaller in the glucose group compared to the control group at 24 hpf. Heart rate is faster in the glucose group compared to the control group on day 2 and 3 with a statistically significant difference. Among zebrafish whole genome, the significantly changed genes are 556 genes up-regulated and 1118 genes down-regulated respectively in high glucose group. The metabolic and Wnt pathways are altered under high glucose condition. These conditions contribute to significant physiological differences that may provide insight on functionality post-embryological development.

High temperature stress affects tomato production both in tropical and sub-tropical environments worldwide. To explore genetic variation for heat tolerance in tomato, 329 transcontinental tomato varieties were evaluated at The Ministry of Municipality and Environment (MME) greenhouses near Doha, Qatar. Preliminary phenotypic analysis identified a diverse set of 71 hybrid and pure line tomato varieties for more detailed studies. The selected subset was examined in the greenhouse in a randomized complete block design under heat stress. The materials were phenotyped for fruit size, fruit weight, fruit hardness, fruit locules, fruit set (%), total soluble solids (TSS), and fruit yield. Significant phenotypic differences among genotypes were observed for all the traits assessed. To explore the genetic basis of variation among varieties the subset was genotyped using 104 SNP markers identified in previous heat tolerance genome wide association studies (GWAS). Nineteen QTL associated SNP markers could reliably select heat tolerant varieties in terms of better fruit yield, fruit set, and TSS. These markers are located on Chromosome 1, 5, 6, 8, 9, and 12. Interestingly, two clusters of markers on chromosome 6 were linked to significant effects on yield, fruit set, and TSS under high temperature. Some markers located within these QTL regions were also reported as associated with heat tolerance in other studies. Eighteen out of nineteen SNP markers were mapped within a gene body. Based on the phenotypic and the genotypic analysis, an elite set of five varieties was selected for approval for heat stress environments in Qatar. These findings have significance not only for Qatar, but they are also valuable for wider application at other locations worldwide. The 19 markers presented here could be adopted by breeders for marker-assisted selection (MAS) for heat tolerance.

Background and Objectives To compare navigator-gated three-dimensional T1-weighted gradient-echo sequences (NG-3D T1W-GRE) with standard breath-hold T1W-GRE (BH T1W-GRE) for the detection of HCC nodules in patients with chronic viral hepatitis which undergo at magnetic resonance imaging (MRI) using gadoxetic acid. Methods and materials We evaluated 58 patients with hepatic nodules at least 1 cm in diameter detected by ultrasound who underwent liver MRI including NG-3D T1W-GRE sequences and breath hold T1-weighted gradient-echo sequences with different flip angles(FA) at 10-25-40° after contrast administration of gadoxetic acid at magnetic scanner operating at1.5 Tesla. Image quality and relative hepatic and nodular enhancement were evaluated by three blinded reviewers. Results In these patients, image quality of NG-3D T1W-GRE was assessed significantly better than quality of BHT1W- GRE (P < 0.005) and relative enhancement was significantly higher than that of BH- T1W-GRE ( P

In the context of rapid urbanization, the spatiotemporal patterns of socio-economic exposed to high seismic hazard in large cities lacks quantitative assessment, thus, it is difficult to understand the evolution of earthquake catastrophe risk there. In this paper, exposure change rate, and absolute and relatively exposure indices were proposed to quantitatively study the changes of spatiotemporal exposure to high seismic hazard in urban areas of large cities (i.e., permanent residents in urban areas more than 1 million) in Chinese mainland, using a set of multi-temporal population, GDP, and built-up datasets and a seismic hazard zoning map. The results show that, 64 out of 78 large cities are entirely or partially located in high seismically hazardous zones. Although the urban areas of large cities in high seismically hazardous zones (HSHUAs) cover only 1.73% (167177 km²) of mainland China, their share of population, GDP, and built-up land amounted to 18.14%, 30.24% and 24.55%, respectively, in 2015. Unprecedented urbanization has led to a dramatic exposure growth in HSHUAs between 1990 and 2015. The population, GDP, and built-up land in HSHUAs increased by 110 million people (with an average annual growth rate of 2.37%), 273.71 trillion USD(average annual growth rate of 11.15%), and 10593 km2 (average annual growth rate of 2.02%), respectively. HSHUAs experienced much faster population and GDP growth than the whole country, while relatively slower growth in built-up land. Exposure growth in HSHUAs also was varied for different types of large cities. Megacities had a higher proportion of increased GDP and population in HSHUAs, induced by industry and population agglomeration. Whereas, Type II large cities had a higher proportion of increased built-up land in HSHUAs, driven mainly by urban sprawl. Our analysis indicates that, for large cities under rapid urbanization, it is an urgent need to strengthen resilient urban planning, renewal and construction.

A dynamic impact test was performed on as-rolled AZ31 alloy with gradient microstructure under various strains. The microstructural evolution and mechanical properties were systematically investigated. As the strain rate gradually increases, an increasing number of twins are formed, facilitating dynamic recrystallization (DRX), and the mechanical properties are also gradually improved as well. The microstructure becomes heterogeneous at higher strain rates, but the peak stress decreases. The impact process results in significantly higher performance due to microstructural refinement, work hardening by dislocations and precipitates. In addition, both the adiabatic shear band and the adjacent crack experience a temperature rise that exceeds the recrystallization temperature of the alloy. This observation also explains the presence of ultrafine recrystallized grains within the adiabatic shear band and the appearance of molten metal around the crack.

The objectives of this study was to assess the impact of a reproductive approach in high-yielding nulliparous and parous Holstein cows on the interestrus interval, estrus detection rates, conception rates, and pregnancy rates. The strategy involved giving GnRH on day 5 following artificial insemination (AI). For nulliparous cows, there appears to be no noticeable effect of GnRH therapy on the interestrus interval. In both groups, nearly all of the cows exhibited an 18–25-day cycle interval (P < 0.05). In the 18–25 day cycle period, the untreated multiparous cows exhibited the highest proportion (P < 0.05), while the treated group demonstrated the highest proportion (P < 0.05) in the 26–35 day cycle interval. The study found that the conception rate was higher in repeat breeder nulliparous and 3+ lactation treated Holstein cows compared with untreated ones. However, the cumulative heat detection rate, pregnancy rate and conception rates were similar in both groups (P > 0.05). Also, this study found that in the hottest months of the year, this therapeutic approach can't counteract the negative effect of heat stress in high-yielding dairy cows. Thus, it is not advised of using the hormonal method to create supplementary corpus luteum across the herd.

Global warming and the associated increasing frequency of heatwaves are on the rise leading to numerous health complications. Diabetic patients are more vulnerable to heat exposure than healthy individuals, owing to their impaired sweating ability, however, little is known about how heat exposure may impact the function of skin cells, commonly keratinocytes. Our recent report provided the first proof-of-concept revealing that the metabolic composition of sweat EVs is associated with metabolic changes in healthy individuals and type 2 diabetes patients. Given this and the shared cellular proprieties of eccrine sweat glands with keratinocytes, we questioned whether the metabolic changes in sweat EVs may mirror the responses of keratinocytes upon heat exposure. To this, we exposed HaCat, which were maintained in low (mimicking healthy condition) and high glucose (mimicking diabetes condition) to acute (90 min), chronic (48 h), and repetitive heat exposure at 40 ⁰C. Through conducting a set of experiments including a targeted metabolomics approach, Greiss assay, western blotting analysis, and electron microscopy studies. The data demonstrate that heat exposure results in substantial changes of metabolite levels belonging to amino acids, pyrimidine metabolism, and glycolysis pathways in high glucose maintained HaCat cells when compared to those noted in low glucose condition. Exploring the molecular mechanisms through which heat exposure may impact the metabolic composition in keratinocytes, our discoveries highlight nitric oxide (NO) as a novel biomarker that the level is correlated with heat duration and frequency. Furthermore, data reveal that the HSP-70 protein levels and mitochondrial morphology are consequently altered. This study provides evidence of shared metabolic alterations in keratinocytes and sweat EVs collected from clinical study and proposes, for the first time, NO as a novel biomarker for monitoring changes in health and diabetes upon heat exposure.

Background: high-altitude work exposes individuals to reduced oxygen levels, imposing physi-ological adaptations. These conditions can induce alterations in the cardiovascular system, po-tentially exacerbating pre-existing health issues and impacting overall well-being of workers in such environments. This study has investigated the cardiovascular challenges for the high-altitude worker on Etna volcano. Methods: Through an observational study, ten healthy, non-smoking male participants underwent cardiovascular and pulmonary function tests at alti-tudes below 500m and above 3000m, simulating work conditions on the volcano. Results: signif-icant findings include elevated systemic blood pressure and heart rate, indicating an increased cardiovascular workload necessary for adaptation to hypoxia. Conclusions: the study highlights the importance of acclimatization to high altitude for minimizing cardiovascular risks among workers. It calls for the development of safety protocols, underlining the critical role of preven-tative measures and specific safety protocols for high-altitude workers.

The fusion of global contextual information with local cropped block details is crucial for segmenting ultra-high resolution images. In this study, we introduce a novel fusion mechanism termed Global-Local Deep Fusion (GL-Deep Fusion) based on an enhanced transformer architecture, which efficiently integrates global contextual information and local details. Specifically, we propose the Global-Local Synthesis Networks (GLSNet), a dual-branch network where one branch processes the entire original image, while the other branch handles cropped local patches as input. The feature fusion of different branches in GLSNet is achieved through GL-Deep Fusion, significantly enhancing the accuracy of ultra-high resolution image segmentation. Particularly effective is GLSNet in identifying tiny overlapping items. To optimize GPU memory utilization, we meticulously design a dual-branch architecture that proficiently leverages the features it extracts, seamlessly integrating them into the enhanced transformer framework of GL-Deep Fusion. Extensive experiments conducted on challenging benchmarks, including DeepGlobe and Vaihingen datasets, demonstrate that GLSNet achieves a new state-of-the-art performance in terms of GPU memory utilization and segmentation accuracy tradeoff.

Aiming at the problem of small size of some spots on apple leaves and the difficulty of accurate detection of spot targets brought by the complex background of the orchard, this paper takes the alternaria leaf spot, rust, brown spot, grey spot and frog eye leaf spot on apple leaves as the research object, and proposes a high-accuracy detection model YOLOv5-Res and lightweight detection model YOLOv5-Res4 are proposed. Firstly, a multiscale feature extraction module ResBlock is designed by combining the Inception multi-branch structure and ResNet residual idea. Secondly, a lightweight feature fusion module C4 is designed to reduce the number of model parameters while improving the detection ability of small targets. Finally, a parameter streamlining strategy based on optimized model architecture is proposed. The experimental results show that the performance of YOLOv5-Res model and YOLOv5-Res4 model is significantly improved, the [email protected] value is improved by 2.8% and 2.2% compared with YOLOv5s model and YOLOv5n model, respectively, and the size of YOLOv5-Res model and YOLOv5-Res4 model is only 10.8MB and 2.4MB, and the number of model parameters is reduced compared with YOLOv5s model and YOLOv5n model. counts are reduced by 22% and 38.3% compared to the YOLOv5s model and YOLOv5n model.

Viral contamination in the aquaculture industry is a significant challenge that requires further research. Emerging evidence suggests that long noncoding RNAs (lncRNAs) play a role in regulating various biological processes, including immunity. However, most studies have focused on model organisms, and little is known about non-coding RNAs in the immune response to viral hemorrhagic septicemia (VHS) in rainbow trout. In this study, we investigated the listing of non-coding RNAs (ncRNAs) in rainbow trout challenged with VHS virus. We explored their potential role in defense-like responses based on transcriptomic analysis of the virus-treated and control groups. As a result of this research, 4207 lncRNAs were identified, of which 182 lncRNAs were differentially expressed between treated and untreated samples. Among 7753 lncRNA transcripts, 1920 were novel intergenic (class code “u”), and 3748 transcripts were potentially novel isoform of lncRNAs. Gene ontology analysis revealed biological pathways associated with the stress response and immune signaling. Pairs of genes such as TP63-MSTRG.62, IL10-MSTRG.9783, IL10-MSTRG.9784, TK1-MSTRG.22826, and MSTRG.17881-GLI1 showed cis interactions, while DOCK10-MSTRG.30015, MSTRG.36357-LOC101268921, and MSTRG.34190-ENPP2 showed trans interactions. In this study, the role of lncRNAs in regulating the expression of the target genes was clearly identified. This finding is consistent with the regulatory processes of immune system responses mediated by cytokines, as well as the regulation of oxygen levels in response to viral infection. The information presented here highlights the various regulatory mechanisms of lncRNAs in the expression of immune system genes in fish treated with VHS virus.

Hydrogen is now recognized as the primary alternative to fossil fuels due to its renewable, safe, high energy density and environmentally friendly properties. Efficient hydrogen production through water splitting has laid the foundation for sustainable energy technologies. However, when hydrogen production is scaled up to industrial levels, operating at high current densities introduces unique challenges. It is necessary to design advanced electrocatalysts for hydrogen evolution reaction (HER) under high current densities. This review will briefly introduce chal-lenges posed by high current densities on electrocatalyst, including catalystic activity, mass dif-fusion and catalyst stability. In an attempt to address these issues, various electrocatalyst design strategies are summarized in detail. In the end, our insights into future challenges for efficient large-scale industrial hydrogen production from water splitting are presented. This review is expected to guide the rational design of efficient high current density water electrolysis electro-catalysts and promote the research progress of sustainable energy.

Benveniste’s experiments – known in the lay press as the “water memory” phenomenon – are generally considered to be a closed case. However, the amount of data generated by twenty years of well-conducted experiments prevents closing the file so simply. An issue, which has been little highlighted so far, merits to be emphasized. Indeed, if Benveniste failed to persuade his peers of the value of his experiments, it was mainly because of a stumbling block, namely the difficulty of convincingly proving the causal relationship between the supposed cause (“informed water”) and the experimental outcomes in different biological models. To progress in the understanding of this phenomenon, we abandon the idea of any role of water in these experiments (“water memory” and its avatars). In other words, we assume that “control” and “test” conditions to be evaluated were physically identical and differed only by their respective designations. We show in this article how simple probabilistic considerations allow to build a model that accounts for all aspects of Benveniste’s experiments. In this model based on probability amplitudes, constructive and destructive interferences emerge – or not – according to the experimental context. The recording of a statistical regularity shapes the intertwined whole constituted by the probability amplitudes of the states of the experimenter’s cognitive structures and of the experimental system. This model provides an alternative explanation to Benveniste’s experiments where water plays no role and where the place of the experimenter is central.

Objective: The goal of this review is to provide a succinct, yet comprehensive, guide to the an-tepartum management of multiple gestations. Methods: This narrative review on twins and multiple gestation provides a concise guide for providers with this ever-growing patient population. PubMED was utilized for literature search. Each reference was evaluated and graded for quality of evidence by US Preventative Services Task Force and Cochrane Review guidelines. Screening, surveillance, and management strategies are delineated succinctly and organized by type of multiple gestation being managed from the lowest risk dichorionic twin pair to the increasingly escalating risks of twins and higher order multiples sharing a placenta and/or amniotic sac. Results: The incidence of twin pregnancies has grown over the past several years, due in large part to delayed reproductive timing and surge in assisted reproductive technologies. Twin pregnancies are associated with higher morbidity for both gravidas and offspring, warranting evidence-based approach in counseling and management. Conclusions: We note the important differences among multiples in chorionicity and amnionicity, in the importance of close surveillance and early delivery. Graded clinical pearls and evi-dence-based recommendations are presented to guide obstetric providers.

Insulated Gate Bipolar Transistor (IGBT) may convey high current and sustain high breakdown voltages; it may provide high power control. In a sense, how IGBT demonstrates the capability of power control was not specifically described, and the equivalent bipolar junction transistors (BJT) activated by an applied bias to the insulated gate is intriguing. As seen in Figure 1, IGBT shows an equivalent circuit structure containing two types of BJT, (NPN-type Bipolar transistor and PNP-type Bipolar transistor), which can be modeled as diode-associated transistor. Apparently, as a bias applies to the controlling gate, the channel beneath the gate oxide gets strongly inversed and turns out to be conductive just like what happens on metal-oxide-silicon field effect transistor (MOSFET), which provides necessary igniting currents to both BJTs and thus causes high current gain flowing through them-selves from the bottom. A proposed and renewed formula provides addressing the above scenario and successfully fitting the measured data that forms the characteristic curves. Some parameters in the proposed formula, which includes size and mobility associated constant, threshold voltage, and Early-Voltage-related lambda for MOSFET, explain and explore the underlying physics. IGBT thus enjoy high input impedance and high current gain due to MOSFET (Insulated Gate) and BJT, respectively. This formula combines both merits of MOSFET and BJT in order to fit the measured data. Indeed, the formula intimately fits IGBT electrical characteristic curves, and thus may be qualified and served as a model. The new model is then advisable for designing power integrated circuit to exactly achieve power saving, power control, and power efficiency.

Among the major systems of high-speed rail, the arch network relationship, wheel-rail relationship and fluid-structure coupling relationship are important links affecting the performance of high-speed rail, and also the main control factors affecting the speed limit of high-speed rail. From this perspective, the contact state and interactive relationship between pantograph and catenary are the key factors affecting the forward performance of high-speed rail. As a key component in the pantograph system, the actuator is responsible for adjusting the contact force and position between the pantograph and the contact line. The performance characteristics of the actuator, such as response speed, accuracy, stability and durability, directly affect the control performance of the whole pantograph system. In this paper, the research status of the active control technology of high-speed railway pantograph is reviewed, and the future development direction is pointed out, which provides a new idea for the development of pantograph technology.

Background: Early postoperative airway management after laryngo-tracheal surgery is crucial. Acute respiratory failure due to glottis’ oedema may occur, requiring reintubation. This can prolong ventilatory assistance, jeopardizing the anastomosis. To date, only judicious steroid administration and fluid management are available to avoid more invasive procedures. High-Flow-Oxygen-Therapy(HFOT) is a noninvasive O2 support method providing humidification, warmed air, Positive-End-Expiratory-Pressure(AIRVO2). No data exist about HFOT use to prevent early complications after laryngo-tracheal surgery. Methods: Between Sept.2020-Sept.2022, 107 consecutive patients underwent laryngo-tracheal surgery received HFOT(Group A). Data and long-term results were compared with those of 80 patients operated between Sept.2018-Aug.2020(Group B), when HFOT was not available. All patients were operated in a single center. No pre- or post-operative settings changed, except for HFOT introduction. We analyzed and compared the risk for “delayed” reintubation (unexpected reintubation within the first 24-48 hours after extubating/laryngeal mask removal) in the two groups. Results: No patients reported HFOT-related adverse events. Control group(B) presented “delayed” reintubation in 37% (p= 0.027), Intensive Care Unit admission in 67%(p=0.005) and longer hospital stay(p=0.001) compared to HFOT group(A). Minor complications rate was 3% in both group and overall mortality was 0%. Re-stenosis was described in 4.6% of HFOT group, without a statistically significant difference (p=0.7006). Conclusions: Our study is the first to investigate HFOT use in patients undergoing laryngo-tracheal surgery, potentially representing a consistent innovation in the peri-operative management of these patients. With the limit of a retrospective series, we would suggest HFOT use for preventing post-operative reintubation rate, possibly reducing ICU admission and hospital stay.

Semantic segmentation of high-resolution remote sensing images provides detailed and precise feature information, playing a pivotal role in decision-making and analysis in sectors such as water management, agriculture, military, and environmental protection. However, most methods merely combine features from various branches directly, without a mechanism for spatial location feature screening, and treat all extracted features as equally important. To overcome these limitations, we introduce a novel spatially adaptive interaction network (SAINet) for dynamic interaction across different features in remote sensing semantic segmentation task. Specifically, we propose a spatial refined module that leverages local context information to filter spatial locations and extract salient regions. Following this, we introduce an innovative spatial interaction module that uses a spatial adaptive modulation mechanism to dynamically select and allocate spatial position weights. This facilitates interaction between local salient areas and global information, allowing the network to focus more on relevant regions. This flexible approach enables the network to capture more informative features, thereby enhancing segmentation accuracy. Experiments conducted on the DeepGlobe, Vaihingen, and Potsdam public datasets confirm the effectiveness and capability of SAINet. Our code and models will be publicly available

This study aimed to identify miRNA editing sites during adipose tissue development in Ningxiang pigs and analyze their characteristics and functions. Based on the small RNA-seq data from subcutaneous adipose tissue samples of Ningxiang pigs at four stages (30, 90, 150 and 210 days), we constructed a developmental atlas of the miRNA editome in adipose tissue of Ningxiang pigs. The characteristics and functions of this editome were further explored through bioinformatics analysis. The findings revealed that a total of 505 miRNA editing sites were identified with C-to-U editing types being the most prevalent, followed by U-to-C, A-to-G and G-to-U. Importantly, these four types of miRNA editing exhibited a base preference. The number of editing sites showed obvious differences among age groups, with the highest occurrence of miRNA editing events observed at 90 days of age and the lowest at 150 days of age. In the miRNA seed region, a total of 9 miRNA editing sites were identified with significant differences in editing levels (P &lt; 0.05), and located in ssc-miR-23a, ssc-miR-27a, ssc-miR-30b-5p, ssc-miR-15a, ssc-miR-497, ssc-miR-15b, and ssc-miR-425-5p, respectively. Target gene prediction and enrichment analysis revealed that the editing of miR-497 may potentially regulate fat deposition by inhibiting adipose synthesis via influencing target binding. These results provide new insights into the regulatory mechanism of pig fat deposition.

CoCrFeNiMn high-entropy alloy coatings were prepared on compacted graphite iron（CGI） through plasma cladding to strength the CGI substrate. The effects of heat treatment temperatures and times on the microstructure and mechanical properties of the CoCrFeNiMn coatings were investigated. After heat treatment, a single FCC phase was remained in the coating as compared to the deposited one, with smaller dendrites, larger dendritic spacing and more Cr-rich compounds precipitated between dendrites. The coatings’ microhardness was increased after heat treatment. After heat treated at 660°C for 90 minutes, the coating had the highest microhardness of 563±6.9 HV0.2, the lowest frictional coefficient of 0.71 and the smallest wear mass loss of 1.12 mg, and it had the best wear resistance.

During the last few years, advancement in the area of biochemistry, science of the material world, engineering and computer-aided testing has directed towards advancement of high-throughput tools for the sake of profiling information encoded in a gene. Single-cell RNA-sequencing (scRNA-seq) tools capable to examine the sequence data from each individual cells and it shows within population variety and permit exploring of cell conditions and transformation by extreme resolution, possibly give out cell sub-types or gene expression fluctuations that are shaded in mass sequencing processes, which shows population-averaged evaluations. Yet, the major disadvantage for this tool is the lack of success to pick out location related details of the RNA transcriptome, as this needs tissue detachment and cell isolation. Location based transcript determination is among the advancements in the area of medical biotechnology as this can find out the molecules like RNA dataset in their intact physical placement in tissue segment with spatial context at the scale of a single-cell, which is very advantageous as compare to single-cell sequencing techniques. These approaches give key observation in the areas of biomedical field sub-disciplines like neurology, embryology, carcinoma study, immune cell investigation and histological activities. Generally, this review mainly focused towards single-cell sequencing methods, technology development, its challenges observed, different expression data analysis mechanisms and their applications in different areas, such as in cancer research, microbes, central nervous system, sex organs and immune-biology, intensifying the essentiality of sequencing tools at single-cell level for the characterization of extremely dynamic individual cells.

Background: In military flight operations fighter pilots work during flights constantly under hyperoxic breathing conditions with supplemental oxygen in varying hypobaric environments. These conditions are suspected to cause oxidative stress to neuronal organ tissues. For civilian flight operations the Federal Aviation Administration (FAA) also recommends supplemental oxygen for flying under hypobaric conditions equivalent to higher than 3048m altitude and makes it mandatory for conditions equivalent of more than 3657m altitude. Aim: We hypothesized that hypobaric-hyperoxic civilian commercial and private flight conditions with supplemental oxygen in a flight simulation in a hypobaric chamber at 2500m and 4500m equivalent altitude would cause significant oxidative stress in healthy individuals. Methods: 12 healthy subjects (6m, 6f, mean age 35,7yrs) from a larger cohort were selected to perform a 3hrs flight simulation in a hypobaric chamber with increasing supplemental oxygen levels (35%,50%,60% and 100% FiO2 via venturi valve equipped face mask) switching back and force between simulated altitudes of 2500m and 4500m. Arterial blood pressure and oxygen saturation were constantly measured via radial catheter and blood samples for blood gases taken from the catheter at each altitude and oxygen level. Additional blood samples from the arterial catheter at baseline and 60% oxygen at both different altitudes were centrifuged inside the chamber and the serum frozen instantly at minus 21°Celsius for later analysis of the oxidative stress markers malondialdehyde low density lipoprotein (M-LDL) and glutathione-peroxidase (GLP) via elisa test. Results: 11 subjects finished the study without adverse events. Whereas PO2 levels increased in the mean with increasing oxygen levels from baseline 96.2 mmHg to 160.9 mmHg at 2500m altitude and 60% FiO2 and 113.2 mmHg at 4500m altitude and 60% FiO2, there was no significant increase in both oxidative markers from baseline to 60% FiO2 at these simulated altitudes. Some individuals had a slight increase, some not at all or even a slight decrease. A moderate correlation (Pearson correlation coefficient 0,55) existed between subject age and glutathione peroxidase levels at 60% FiO2 at 4500m altitude. Conclusion: Supplemental oxygen of 60% FiO2 in a flight simulation comparing to flying in cabin pressure levels equivalent to 2500m-4500m altitude does not lead to a significant increase or decrease in the oxidative stress markers M-LDL and GLP in serum of arterial blood.

Leaf area estimation is a critical component in the study of plant growth and productivity within agricultural systems. This research introduces the LeafArea package, a specialized tool designed to calculate the leaf area of six distinct Andean fruit species: S. quitoense, S. betaceum, P. peruviana, R. fruticosus, P. ligularis and P. edulis. Leveraging response variables such as species type, leaf length and width, the package employs advanced machine learning algorithms to estimate leaf area accurately. The primary focus of the study is to identify the most effective model for describing the relationship between leaf width, length, and area for each plant species. Currently, the LeafArea package utilizes four different machine learning algorithms, namely generalized linear model (GLM), generalized linear mixed model (GLMM), Random Forest and XGBoost. Among these, XGBoost stands out as a top-performing algorithm, exhibiting exceptional predictive accuracy. The evaluation metrics employed in the program provide valuable insights for researchers, aiding in informed decision-making. Specifically, XGBoost demonstrates significantly lower prediction errors and approaches a near-perfect R2 value, emphasizing its potential to enhance predictive accuracy. These results underscore the efficacy of machine learning techniques, as a compelling choice for researchers seeking precise and robust predictions in leaf area estimation. The LeafArea package thus represents a valuable tool for advancing our understanding of plant growth dynamics, resource allocation, and overall productivity within agricultural ecosystems.

This paper shows the development of a numerical analysis model, which enables the calculation of the cargo transport capacity of a vehicle that circulates through a vacuum tube at high speed, whose effectiveness in transport is analyzed. The simulated transportation system is based on vehicles moving in vacuum tubes at high speed, a concept commonly known as Hyperloop, but assuming the vehicles for cargo containers. For the specific vehicle proposed, which does not include a compressor and levitates on magnets, the system formed by the vehicle and the vacuum tube has been conceptually developed, establishing the corresponding mathematical relationships that define its behavior. To properly model the performance of this transport system, it has been necessary to establish the relationships between the design variables and the associated constraints, such as the Kantrowitz limit, aerodynamics, transport, energy consumption, etc. Once the model was built and validated, it was used to analyze the effects of the variation of the number of containers, the operating speed and the tube length, considering the total and specific consumption of energy. Once the most efficient configuration was found regarding energy consumption and transport effectiveness, the complete system was calculated. The results obtained constitute a first approximation for the pre-design of this transport system and the built model allows different alternatives to be compared according to the design variables.

High-rise buildings represent technological, urban and life-style trends of the modern urban landscape, yet there are limited data regarding their embodied carbon and environmental impacts, particularly when compared to low- or mid-rise buildings. Given that the projected growth of the global urban population by 2050 requires cities with higher density and potentially greater number of high-rise buildings, it is crucial to develop a clear understanding of the embodied carbon and environmental impacts of high-rise buildings. This article utilizes the building in-formation modelling (BIM) based life cycle assessment (LCA) in Revit and Tally to examine the embodied carbon and environmental impacts of an actual high-rise building structure case-study in Chicago that uses hybrid concrete steel structure. The results show that the embodied carbon and environmental impacts of the high-rise building structure are dominated by the impacts of the product stage in the building life cycle, and concrete as the main structural material. Specifically, this study reveals that concrete constitutes a substantial 91% share of the total mass of the building structure, with 74% contribution to life cycle global warming potential, 53% to acidification po-tential, 74% to eutrophication potential, 74% to smog formation potential, and 68% to non-renewable energy. On the other hand, steel accounts for 9% of the building structure mass, estimated to constitute 26% of the global warming potential, 47% to acidification potential, 26% to eutrophication potential, 26% to smog formation potential, and 32% to non-renewable energy.

Present study focuses on the synthesis and characterisation of a lightweight ceramic material with electromagnetic interference (EMI) shielding properties, achieved using mullite containing micrometer-sized hollow spheres (cenospheres) and CoFe2O4 nanoparticles. The research explores compositions with varying CoFe2O4 content, ranging from 0 up to 20 wt.%. Сonventional sintering in an air atmosphere is carried out at a temperature between 1100-1300 °C. The addition of ferrite nanoparticles was found to enhance the sintering process of cenospheres, resulting in improved material density and mechanical properties. Furthermore, the study reveals a direct correlation between the concentration of ferrite nanoparticles and the electromagnetic properties of the. By increasing the concentration of ferrite nanoparticles, the electromagnetic shielding effect of the material (saturation magnetization (Ms) and remanent magnetization (Mr)) was observed to strengthen. These findings provide valuable insights into the design and development of lightweight ceramic materials with enhanced electromagnetic shielding capabilities. The synthesized ceramic material holds promise for various applications that require effective electromagnetic shielding, such as in electronics, telecommunications, and aerospace industries.

This study investigates the microstructures and deformation mechanism of hetero-structured pure titanium under different high strain rates (500 s-1，1000 s-1，2000 s-1). The influence of strain rate on the deformation mechanism is examined. As the strain rate increases, the dominance of dislocation slip decreases while deformation twinning becomes more prominent. Notably, at a strain rate of 2000s-1, nanoscale twin lamellae are activated within grain with a size of 500nm, which is a rarely observed phenomenon in pure Ti. Additionally, martensitic phase transformation is also identified. These findings can greatly enhance our understanding of the mechanical responses of Ti and broaden the potential applications of Ti in dynamic deformation scenarios.

As one of the important wastes, waste PET pollutes human living and natural environment seriously. PET is an important solid waste that needs to be recycled at present. The complete degradation of PET was realized at low temperature. The lipophilic hydrophobic membrane was formed on the surface of stainless steel mesh (SSM) by a simple dip coating method, and the oil-water separation material was successfully prepared. Due to the load of degradation products, the surface roughness of SSM increased from 19.09 μm increased to 62.33 μm. The surface changed from hydrophilic to hydrophobic, and the water contact angle increased to 123o. The oil-water separation flux of modified SSM is 9825 L/(m2·h) and the separation efficiency is 98.99%. The modified SSM has good reuse performance. This hydrophobic modification method can also be used to modify other porous substrates, such as activated carbon, filter paper, foam, and other materials. In this study, the porous substrate modified by the degradation product of waste PET was used to prepare oil-water separation materials, which not only solved the problem of white pollution, but also reduced the dependence on non renewable resources in the conventional preparation methods of oil-water separation materials. The research provided new raw materials and methods for the industrial production of oil-water separation materials, and had important application prospects.

The use of substances to improve sports performance is a widespread phenomenon among adolescents. Several anti-doping programs have been developed, mainly based on knowledge-based evidence. The main aim of the present study was to implement an anti-doping intervention in sports high school students, based on psychological framework, such as Socio-Cognitive Theory, through the development of a Serious Game (SG), i.e., a digital learning based on the game. The experimental design included an intervention group (n=167; F=37.7%; Meanage=17.5 years) and a control group (n=112; F=42%; Meanage=17.6). Both of groups completed the same questionnaire in two different occasions (i.e., time 1 and time 2), for measuring doping intention, self-regulatory efficacy to resist social pressure for the use of substances, moral disengagement, and doping knowledge. Data were analyzed through repeated measures of Group X Time ANOVA, demonstrating some degree of efficacy of the intervention, in particular, in terms of decrease of doping intention and the strengthening of doping knowledge. Moreover, we demonstrated that the score obtained during the implementation of the Serious Game partially could represent a coherent measure of the participants’ beliefs regarding doping. These results could be considered a starting point for future research to better develop technological anti-doping interventions.

The flow stress of face-centered cubic (FCC) metals exhibits a rapid increase near a strain rate of 104 s-1 under fixed strain conditions. However, many existing constitutive models either fail to capture the mechanical characteristics of this plastic deformation or use piecewise strain rate hardening models to describe this phenomenon. Unfortunately, the piecewise models may suffer from issues such as discontinuity of physical quantities and difficulties in determining segment markers, and struggling to reflect the underlying physical mechanisms that give rise to this mutation phenomenon. In light of this, this paper proposes that the abrupt change in flow stress sensitivity to strain rate in FCC metals can be attributed to microstructural evolution characteristics. To address this, a continuous semi-empirical physical constitutive model for FCC metals is established based on the microstructural size evolution proposed by Molinari-Ravichandran and the dislocation motion slip mechanism. This model effectively describes the mutation behavior of strain rate sensitivity under fixed strain, particularly evident in the annealed OFHC. The predicted results of the model across a wide range of strain rates (10-4 − 106 s-1) and temperatures (77 − 1096 K) demonstrate relative errors generally within ±10% of the experimental values. Furthermore, the model is compared to five other models, including Mechanical Threshold Stress (MTS), Nemat-Nasser-Li (NNL), Preston-Tonks-Wallace (PTW), Johnson-Cook (JC), and Molinari-Ravichandran (MR) models. A comprehensive illustration of errors reveals that the proposed model outperforms the other five models in describing the plastic deformation behavior of OFHC. The error results offer valuable insights for selecting appropriate models for engineering applications and provide significant contributions to the field.

Conclusions: HRCT is a valuable tool in preoperative assessment of cholesteatoma, helping in making surgical decisions. It can accurately predict the extent of disease and is helpful for detecting unapparent dangerous situations. However it is not very accurate in detecting Fallopian canal and stapes erosion.

Emerging evidence has indicated the involvement of extra-hypothalamic kisspeptin and GnRHR in reproductive function. In this study, we evaluate if maternal exposure to the pesticide chlorpyrifos (CPF) and/or a high-fat diet (HFD) have an impact on the expression of kisspeptin and GnRHR in reproductive organ of offspring’s rats. 16 Pregnant rats are divided into 4 groups, control group (n=4), CPF group (4 rats exposed daily to 1/mg/kg/day), HFD group (4 rats randomly fed a 5,25 kcal/g HFD), co-exposed group (4 rats exposed to CPF and HDF). At postnatal development PND60, males and female offspring were sacrificed. The reproductive organs (ovary and testis) were removed and histological, immunohistological analysis and in silico quantification (software Tissuefax, HistoQuest) was assessed to investigate the impact of different treatment on kisspeptin and GnRHR expression in reproductive organs. The main outcomes of the study showed a significant decrease in rat offspring’s body weight in CPF group from PND30 andPND60 (p&lt;0.05 and p&lt;0.01, respectively). Histological analysis shows a significant increase in atretic follicle and abnormal testis structure with germ cell desquamation at CPF exposed group. The immunodetection quantification of protein shows a significant decrease in GnRHR and kisspeptin in HFD and CPF exposed group, respectively in testis rat offspring. Perinatal exposure to CPF and HFD exposure affect the reproduction function of rat offspring.

Background: A prognostic index validated for the outcomes of advanced high-grade serous ovarian cancer (HGSOC) patients with neoadjuvant chemotherapy (NACT) is still lacking. We therefore developed an ovarian neoadjuvant chemotherapy prognostic index (ONCPI) to enhance predictive accuracy. Methods: We analyzed clinicopathologic feature of advanced HGSOC patients receiving platinum-based NACT. Blood inflammatory composite markers were calculated and binary-transformed by optimal cutoffs. The omental hematoxylin and eosin (H&E) stained slides were selected for the assessment of chemotherapy response score (CRS). Logistic regression analyses and Cox proportional hazard regression model were utilized to develop a prognostic index. Results: Multivariate analysis showed that CRS and neutrophils-to-lymphocyte ratio (NLR) are independent risk factors for platinum-chemotherapy response. Meanwhile, Kaplan–Meier and Cox regression analysis revealed that CRS score was significantly correlated with PFS and OS, and NLR-high patients was associated with poor OS. We further developed an ONCPI model based on the CRS score and NLR level. Survival analysis suggested that patients with score 0 and 1 of ONCPI were significantly associated with improved PFS and OS. Conclusions: The ONCPI score emerges as a significant prognostic marker for predicting NACT outcomes in advanced HGSOC patients. Its integration into clinical practice and risk-stratified trial design is conceivable.

Type 1 diabetes (T1D) is one of the most prevalent endocrinological diseases among children and young adults, with a growing incidence rate reaching up to 2.9 new cases per year per 100 000 persons below 15 years of age. We report the rare case of a 20-year-old female patient with T1D, hemoglobin D (HbD) heterozygote variant and high myopia of -10,00 spheric diopters and describe the retinal microvascular alterations visible on OCT angiography (angio-OCT). The patient also presented severe stature deficit (less than 3 standard deviations) and delayed puberty, which could not be explained only by suboptimal glycemic control, indicated a possible hypopituitarism. The HbA1c level evaluated with high performance liquid chromatography (HPLC) method was 6.5%, a falsely low value due to the HbD hemoglobinopathy. On ophthalmic evaluation the angio-OCT scan showed the following retinal microvascular alterations for the RE: the FAZ area vas 0.39 mm2, the FAZ perimeter was 2.88 mm and the circularity index was 0.58; for the LE: the FAZ area vas 0.34 mm2, the FAZ perimeter was 3.21 mm and the circularity index was 0.41. Clinicians should consider high performance retinal screening methods such angio-OCT evaluation for young T1D patients, especially for those with associated pathologies like high myopia and hemoglobinopathies. Moreover, multiple evaluation methods of the HbA1c values are mandatory as hemoglobinopathies can interfere with HbA1c assay methods accuracy.

Resonant light scattering by mesoscale dielectric spheres has received enormous attention and found many interesting applications. The recently emerged field of Mesotronics provides novel opportunities for wavelength-scaled optics and new fundamental aspects are still being uncovered. It has recently been demonstrated that high-order Mie resonances can be excited in homogeneous low-dissipation mesoscale dielectric spheres, leading to the generation of intense magnetic fields. This Letter describes a simple and effective way to drastically enhance the superresonance effect. Proof-of-principle results for the first time show that yet one more novel phenomenon of increasing the intensity of the magnetic field without changing the resonant Mie size parameter of the sphere by introducing an air cavity. In such a dielectric cenosphere (from two Greek words “kenos” - hollow and “sphaira” - sphere), by correct choosing of the air cavity size, it is possible to increase the intensity of the electromagnetic fields at the poles of the sphere by an order of magnitude due to increasing of amplitude of resonant partial wave coefficient.

This paper presents the design of a miniaturized polyimide-based antenna for Ultra-Wideband (UWB) communication. Miniaturization is achieved through the utilization of adhesive material with a high dielectric constant (high-Dk). The goal of this work is to investigate the impact of such material on the antenna performance and to optimize its design for UWB operation. The manufacturing of the antenna using the proposed structure was developed and the prototype of antenna for UWB high-band (6 - 9 GHz) is measured and analyzed. By leveraging the high Dk of the adhesive material, the simulation and measurement results showed that the proposed antenna with high Dk adhesive film can achieve the compact dimension with good performance in gain, and time domain characteristics. The results of this study show a potential of exhibiting a reduction in the size of the antenna and will contribute to the advancement of miniaturized UWB antenna technology.

The GPA is a universally recognised and utilised metric of academic performance that is considered to also measure a student’s potential for academic performance in the future. In this short communication we examine to what extent the GPA of the first grade of high school predicts performance in the later grades of high school, either generally (as classified in excellent student, strong student, weak student or very weak student) or more accurately (as indicated by the exact GPA in the next grade). We also put to the test the widely held notion that it might be best if core courses such as language and mathematics contributed more to the calculation of the GPA compared to secondary courses such as physical education or music. Our findings confirm the predictive properties of the GPA but strongly rebut the notion that a weighted GPA might achieve a better reflection of students’ potential. The study is based on the academic records of every student in Greece that progressed from first to third grade of high school in the 2016-2019 period. This data set contains records of more than 85,000 students, making it one of the most extensive studies ever conducted on the topic of the properties of the GPA.

High-fidelity patient simulation (HFPS) is widely used in professional training to enhance students’ competence in clinical management. Problem-solving (PS) and clinical reasoning (CR) skills are essential to developing students in professional competence in safe and effective care. These two skills should be initiated at the early training. However, little is known about the effects of HFPS on developing PS and CR skills in first year undergraduate students. Therefore, this pre- and post-experimental study aimed to investigate the effects of HFPS on development of PS and CR skills in first-year nursing students. The students were required to go through four sessions, preparation, pre-briefing and orientation, simulation role-playing, and debriefing, for the HFPS. The study utilized the Problem-Solving Inventory (PSI) and the Nurses Clinical Reasoning Scale (NCRS) to measure problem-solving and clinical reasoning abilities before and after HFPS. Bivariate analysis, one-sample t-test, and independent t-test were performed to evaluate the performance of the PS and CR skills at the two study periods. One hundred eighty-nine students were recruited, with a mean age of 20.56 years, and 73% were female students. The analytic results showed that the PSI, particularly in domains of Problem-Solving Confidence (PSC) (p&lt;0.001) and overall PS (p&lt;0.001), and the CR (p&lt;0.001) had significant improvement after HFPS. The study concluded that HFPS is an effective innovative method to significantly improve students’ problem-solving and clinical reasoning abilities. Nurse educators play an important role in providing explicit learning instructions in a simulation guideline that directs and guides students to learn at each stage of HFPS. Students should take more initiative and engage in their learning through HFPS to enhance their competence in knowledge and higher intellectual skills for personal and professional developments.

In this study, we had investigated the use of high-pressure homogenization (HPH) as a novel pretreatment method for the extraction of sodium alginate (SA) from Laminaria japonica. Our results demonstrated that under optimal condition of 100 MPa HPH pressure, 4 cycles, pH 6.0, and 0.5% ethylene diaminetetra acetic acid tetrasodium salt (EDTA) concentration (w/v) for 3.0 hours, the extraction yield of HPH reached 34%, which was higher than that achieved by previous methods such as complex enzyme hydrolysis (CE), ultrasonic-assisted extraction (UAE), and complex enzyme-ultrasonic combined method (CE-UC). To further characterize the extracted SA, we conducted a comprehensive analysis using SEM, FTIR, MRS, NMR, XRD, TGA, and T-AOC assay. Our findings revealed the following: 1) HPH treatment significantly disrupted the structure of L. japonica cells and reduced their crystallinity to 76.27%, the lowest among all pretreatment samples; 2) the extracted SA had a greater tendency to form elastic gels; and 3) the antioxidant activity of HPH-extracted SA reached 0.02942 mgVceq∙mg-1, which was the highest among all tested methods. Based on these results, we concluded that HPH extraction not only increased the yield of SA but also enhanced its antioxidant activity.

Graphene nanostructures (GNS) are among the most promising materials for creating supercapacitors. However, GNS are still not used in creating supercapacitors due to the impossibility of obtaining large volumes of high-quality material at an acceptable cost. In this work, we investigated the efficiency of using few-layer graphene (FLG) with the number of layers is not more than 5 synthesized under Self-propagating high-temperature synthesis (SHS) conditions as basic material for supercapacitors. Using the SHS process makes it possible to synthesize large volumes of FLG without Stone-Wales defects. It was found that the synthesized FLG makes it possible to obtain better results than using classical materials, namely activated carbon (AC). It was found that the sample based on FLG has a higher specific capacitance – 65 F×g-1 compared to the sample from AC, the specific capacitance of which is 35 F×g-1, for a speed of 5 mV×s-1 these values are 170 and 64 F×g-1, respectively. The drop in capacitance over 1000 cycles was 4%, which indicates a sufficiently high stability of FLG and allows us to consider FLG as perspective material for use in supercapacitors.

Without doubt, the social and environmental business impact will become more important as the governments cannot take care about these problems. Thus, launching the EU Green deal rules, World Global Sustainable Development Goals, corporate social responsibility (CSR) activities and strategies are part of this global commitment. Additionally, CSR is strongly connected to the exploration of (social) market awareness and technology development and application as it focusses on social, environmental and economic business impact. The main goal of the paper is to verify that contemporary greener CSR strategies are beneficiary activity for high-tech companies because of better competitive advantages acquisition through management of corporate reputation risk and patenting innovative technologies. The structure of the paper is the next: 1. Introduction – explanation the previous researches that explore the relation: CSR strategy – high-tech company competitiveness; 2. State of art – exploring the corporate reputation and patent rights as factors in CSR strategy; 3. Patent monopoly and CSR – research the connection between reputation risks of patents rights and CSR strategy; 4. Business performance and CSR reporting – briefly research methodology is presented as some results from Bulgarian companies; 5. Discussion and conclusions – summarizing a methodology for patent rights and reputation risk management for better CSR effects.

Although instructional feedback plays an essential role in regulating learning and improving performance, few studies have systematically investigated the needs of teachers and students for instructional feedback system or developed designs and experiments, especially at the high school level. To address this research need, the present study investigated the needs of selected students and teachers in a high school in Hubei Province, China, and designed and developed a diagnostic visual feedback system for an experimental study with 125 students from a 10th-grade biology class in the same high school. The results showed that this diagnostic visual feedback report improved student performance (ES=0.37) and that functions such as misconception location, knowledge diagnosis, and knowledge alert were well received by students. These findings have multiple implications for facilitating the design and development of diagnostic visual feedback system.

Selenium (Se) is an essential trace element for human beings and Se supplementation is of great significance. In this paper, high selenized Gastrodia elata Blume Polysaccharides (SeGEP) were obtained through pre-sulfation before conducting the selenylation modification process, which owned a maximum Se content reach to 2.29%. UV, FT-IR, NMR, SEM, EDX, HPLC, size-exclusion chromatography and periodate oxidation analysis showed that the seleninic group had been successfully introduced into GEP with the substitution position at C-6 of glucose. Immunostimulating assays were conducted in vitro and in vivo on RAW 264.7 cells and cyclophosphamide (CTX)-induced mice model, respectively. The results showed that Se-GEP enhanced RAW264.7 cells proliferation, cell phagocytosis, and secretion of nitric oxide (NO) and interleukin (IL)-1β factors. In addition, Se-GEP enhanced the immunologic activity of CTX-treated mice by increasing the spleen and thymus indices, enhancing the phagocytic function, and activating both Th1 and Th2 lymphocytes. The current outcome also suggested that Se-GEP with covalently bonding Se group possessing increased safety and has a potential dietary selenium nutrient for improving human immunity.

Dicarbonyls are electrophiles able to generate the so-called advanced glycation end-products (AGEs). Human exposure occurs via ingestion (e.g., food), inhalation (e.g., electronic cigarettes) and dysregulation of endogenous metabolic pathways (e.g., glycolysis). Biological systems can prevent AGEs formation via enzymatic and nonenzymatic reactions. However, the continuous exposure to dicarbonyls may cause the depletion of endogenous substrates and the beginning of AGEs accumulation (i.e., carbonylation). Since this process has been associated with multiple disorders, several studies advocated the use of dicarbonyl binders as food preservatives or as drugs aimed at mitigating carbonylation damages. As reported for other toxicants (e.g., HNE, acrolein), the screening of selective and potent binders can be performed by measuring the residual amount of a selected dicarbonyl substrate, upon its incubation with candidate binders. Unfortunately, naturally occurring dicarbonyls are poorly responsive to many detectors (e.g., UV or MS). For this reason, most of the screening methods that have been reported to date relies on indirect quantification upon derivatization. However, this strategy can potentially lead to inaccurate results since the tested compounds can affect the derivatization yield. Therefore, we herein reported the use of benzylglyoxal (BGO) as a convenient, UV responsive, dicarboyl surrogate. By using BGO as a substrate, we setup an easy and cheap chromatographic assay for the direct measurement of the binding activity towards dicarbonyls, without derivatization. The method was qualified by assessing the binding ability of some known dicarbonyl binders, obtaining results consistent with literature.

This article investigates the potential for carbon reduction in urban parks in Shangqiu City using high-resolution remote sensing imagery. The aim is to guide modern urban carbon neutrality strategies. The carbon reduction potential is estimated based on the mitigation of the urban heat island effect by park greenery, which reduces energy consumption. The parks are regarded as cool island centers, and 100 cooling gradients are gradually formed outward until the temperature reaches that of impermeable urban surfaces. The energy saved by the parks in mitigating the heat island effect is statistically calculated as the carbon reduction potential of urban park greenery. Additionally, this article classifies the sample parks into different categories and selects 26 landscape metrics to analyze their relationship with carbon-saving potential and driving factors.

Increasing the loading density of nanoparticles on carbon support is essential for making Pt-alloy/C catalysts practical in H2-air fuel cells. The challenge lies in increasing the load-ing while suppressing the sintering of Pt-alloy nanoparticles. This work presents a 40% Pt-weighted sub-3 nm PtCo/C alloy catalysts via a simple incipient wetness impregnation method. By carefully optimizing the synthetic conditions such as Pt/Co ratios, calcination temperature and time, the size of supported PtCo alloy nanoparticles is successfully con-trolled below 3 nm, and a high electrochemical surface area achieves of 94 m2/g is achieved, which is 2.8 times of commercial PtCo/C-TKK catalysts. Demonstrated by elec-trochemical oxygen reduction reaction, PtCo/C alloy catalysts present an enhanced mass activity of 0.45 A/mg at 0.9 V vs. RHE, which is 1.7 times that of PtCo/C-TKK catalyst. Therefore, the developed PtCo/C alloy catalyst can potentially be a highly practical cata-lyst for H2-air fuel cells.

This paper presents a comprehensive study and the analysis of a topology of a no isolated DC-DC intituled Double Quadratic Boost converter with high static gain. This converter has the main advantage of high static gain and low voltage stress on its switches. The article will first present the theoretical analysis of the converter operating in an open loop. The objective of the work is the mathematical modeling and the control strategy of the converter, as well as the validation through closed-loop experimental results. Besides, we presented the practice test results to demonstrate the operation of the converter, such as the static gain experimental curve, the practice efficiency of the converter, and the control of the output voltage, as well as the capacitor voltage balance control. The authors designed a prototype for 1 kW, with a switching frequency of fs=50kHz, with FPGA-based command and modulation.

High-quality rice (Oryza sativa L.) is increasingly widely planted in China with the improvement of people's living standards and the achievement of rice breeding efforts in recent years. However, the agronomic and physiological performances of high-quality indica rice (HQIR) under different nitrogen(N) application conditions in southern China are little known. Two-year consecutive field experiments were conducted with two HQIR and two ordinary-quality indica rice (OQIR) varieties under moderate and high N application rates, with yield and yield components, biomass, N up-take, and their related traits investigated. We found that grain yields of HQIR were slightly de-creased, but grain yields of OQIR were significantly increased by 6.60%-8.88% under high N rate compared with moderate N rate in both years. Thereby, OQIR produced 8.34%-11.87% and 22.00%-22.50% higher grain yield than HQIR under moderate and high N rates, respectively. The different responses of grain yield to N application rates were mainly due to decreased grain set-ting rate in HQIR and increased spikelets m-2 in OQIR under high N rate. Furthermore, high N rate significantly reduced pre-anthesis AE and improved grain-leaf area ratio, while did not in-crease post-anthesis DM compared with moderate N rate in HQIR, which might result in carbon metabolic deterioration and imbalance of source-sink relationship and subsequently lower supply of carbohydrate to panicle. Our results suggest that a moderate N rate (165 kg N ha-1) is beneficial for HQIR varieties to balance the maximum grain yield and high quality in southern China

Many advanced reactor concept designs rely on high-assay low-enriched uranium (HALEU) fuel, enriched up to approximately 19.75% 235U by weight. Efforts are underway by the US government to increase HALEU production in the United States to meet anticipated needs. However, very little data exists for validation of computational models that include HALEU, beyond a few fresh fuel benchmark specifications in the International Reactor Physics Experiment Evaluation Project. Nevertheless, there is other data with potential value available for developing into quality benchmarks for use in data and software validation efforts. This paper reviews the available evaluated HALEU fuel benchmarks and some of the potentially relevant benchmarks for fresh highly enriched uranium. It then introduces experimental data for HALEU fuel irradiated at Idaho National Laboratory, from relatively recent irradiation programs at the Advanced Test Reactor. Such data should be evaluated and, if valuable, collected into detailed benchmark specifications to meet the needs of HALEU-based reactor designers.

Co-doped SnO2 nanocrystals with tetragonal rutile-type (space group P42/mnm) structure have been investigated using in-situ high-pressure synchrotron angle dis-persive X-ray diffraction till 20.9 GPa at ambient temperature. The analysis of ex-perimental results based on Rietveld refinements suggest that rutile-type SnO2 un-dergoes a structural phase transition at 14.2 GPa to an orthorhombic CaCl2-type phase (space group Pnnm) with no coexistence during the phase transition. No further phase transition is observed till 20.9 GPa. The low-pressure and high-pressure phases are related via a group/subgroup relationship. However, as a discontinuous change in the unit-cell volume is detected at the phase transition, thus, the phase transition can be classified as first-order type. On decompression the transition is found to be re-versible. The results are compared with previous high-pressure studies on SnO2.

Large-scale land cover plays a crucial role in global resource monitoring and management, as well as research on sustainable development. However, the complexity of the mapping process, coupled with significant computational and data storage requirements, often leads to delays between data processing and product publication, creating challenges for dynamic monitoring of large-scale land cover. Therefore, improving the efficiency of each stage in large-scale land cover mapping and automating the mapping process is currently an urgent and critical issue that needs to be addressed. We propose a high-performance automated large-scale land cover mapping framework(HALF) that introduces high-performance computing technology to the field of land cover production. HALF optimizes key processes, such as automated sample point extraction, sample-remote sensing image matching, and large-scale classification result mosaic and update. We selected several 10°×10° regions globally and the research makes several significant contributions:(1)We design HALF for land cover mapping based on docker and CWL-Airflow, which solves the heterogeneity of models between complex processes in land cover mapping and simplifies the model deployment process. By introducing workflow organization, this method achieves a high degree of decoupling between the production models of each stage and the overall process, enhancing the scalability of the framework. (2)HALF propose an automatic sample points method that generates a large number of samples by overlaying and analyzing multiple prior products, thus saving the cost of manual sample selection. Using high-performance computing technology improved the computational efficiency of sample-image matching and feature extraction phase, with 10 times faster than traditional matching methods.(3)HALF propose a high-performance classification result mosaic method based on the idea of grid division. By quickly establishing the spatial relationship between the image and the product and performing parallel computing, the efficiency of the mosaicking in large areas is significantly improved. The average processing time for a single image is around 6.5 seconds.

The number of obese people worldwide is rising dramatically, with 51% of the global population expected to be obese or overweight by 2035. And it is usually involved in a variety of chronic diseases, including diabetes, hypertension, cardiovascular and cerebrovascular diseases. In the process of obesity, adipose tissue expands indefinitely, which induces metabolic dysfunction. Here, we confirm the role of succinate in the intervention of obesity. Through adding succinate to drinking water, high-fat diet induced obese mice were associated with the lower fat mass, and improved glucose tolerance and energy expenditure. These metabolic changes are accompanied by increased expression of lipolysis genes and decreased lipogenesis genes, especially in subcutaneous adipose tissue. In summary, supplement of succinate improves lipid deposition and metabolic health in obese mice.

Diethyldithiocarbamate (DDTC) has been employed in the sulfide ore flotation process, due to its excellent collection performance. Herein, we investigated the interfacial adsorption behavior of DDTC on four mineral phases of high-sulfur residue — sulfur, pyrite, sphalerite and lead sulfate. The adsorption behavior — adsorption structure and energy and electron localization function cross section — of DDTC and H2O were explored using density function theory calculation. The result was helpful to construct a co-adsorption model of DDTC and H2O, which was validated by the pure minerals flotation operation and the characterization of fourier transform infrared spectra. The co-adsorption model indicated that the DDTC adsorption on the sulfur, sphalerite and lead sulfate was weak with physical bonding, while its adsorption on the pyrite was strong with chemical bonding. Practical bench-scale operation of high-sulfur residue flotation was performed, whose result was different from that obtained from the pure mineral flotation. To explain the difference, our developed model predictions and the mineral fugacity pattern analysis on the high-sulfur residue flotation were synergistically used. Overall, this work first proposed the co-adsorption model of DDTC and H2O and provided important insights into the interfacial adsorption in the high-sulfur residue flotation.

The emergence of various electronic devices and equipment such as electric vehicles and drones requires higher energy density energy storage devices. Lithium-sulfur batteries (LSBs) are considered as the most promising new generation energy storage system owing to high theoretical specific capacity and energy density. However, the severe shuttle behaviors of soluble lithium polysulfides (LiPSs) and the slow redox kinetics lead to low sulfur utilization and poor cycling stability, which seriously hinder the commercial application of LSBs. Therefore, various catalytic materials have been employed to solve these troublesome problems. High entropy materials (HEMs), as advanced materials, can provide unique surface and electronic structures that expose plentiful catalytic active sites, which opens new ideas for the regulation of LiPSs redox kinetics. Notwithstanding many instructive reviews in the land of LSBs, while this review aims to offer a complete and shrewd summary of the current progresses in HEMs-based LSBs, including in-depth interpretation of design principles and mechanistic electrocatalysis functions as well as pragmatic perspectives.