Corporate Diagnosis is now recognized as an important tool by decision makers to predict and correct burgeoning problems that a corporation may face. Methods based on this model stem from the use of mathematics and are increasingly being applied in the analysis of production processes. The goal of this paper is to use a logistic regression to design a scoring model for non-financial corporations in industry. Based on the data obtained from the Registry of the Slovak Republic for 738 non-financial corporations, according to SK NACE 26, SK NACE 27, the proportional financial metrics, using the logistic regression method, were calculated. By applying these methods, two logistic regression models were found to reliably estimate the probability of bankruptcy for a firm.

Background: According to the National Highway Traffic Safety Administration, 116 pedestrians were killed in motor vehicle crashes in Ohio in 2015. However, no study to date has analyzed crashes in Ohio exploring the factors contributing to the pedestrian injury severity resulting from motor vehicle crashes. This study fills this gap by investigating the crashes involving pedestrians exclusively in Ohio. Materials and Methods: This study uses the crash data from the Highway Safety Information System, from 2009 to 2013. The explanatory factors include the pedestrian, driver, vehicle, crash, and roadway characteristics. Both fixed- and random-parameters ordered probit models of injury severity (where possible outcomes are major, minor, and possible/no injury) were estimated. Results: The model results indicate that being older pedestrian (65 and over), younger driver (less than 24), driving under influence (DUI), being struck by truck, dark-unlighted roadways, six-lane roadways, and speed limit of 40 mph and 50 mph were associated with more severe injuries to the pedestrians. Conversely, older driver (65 and over), passenger car, crash occurring in urban locations, daytime traffic off-peak (10 AM to 3:59 PM), weekdays, and daylight condition were associated with less severe injuries. Conclusion: This study provides specific safety recommendations so that effective countermeasures could be developed and implemented by the policy makers, which in turn will improve overall highway safety.

The number of SIEM introduction is increasing in order to detect threat patterns in a short period of time with a large amount of structured/unstructured data, to precisely diagnose crisis to threats, and to provide an accurate alarm to an administrator by correlating collected information. However, it is difficult to quickly recognize and handle with various attack situations using a solution equipped with complicated functions during security monitoring. In order to overcome this situation, new detection analysis process has been required, and there is an effort to increase response speed during security monitoring and to expand accurate linkage analysis technology. In this paper, reflecting these requirements, we design and propose profiling auto-generation model that can improve the efficiency and speed of attack detection for potential threats requirements. we design and propose profiling auto-generation model that can improve the efficiency and speed of attack detection for potential threats.

In this paper, we propose a simple tool to help the energy management of a large buildings stock defining clusters of buildings with the same function, setting alert thresholds for each cluster, and easily recognizing outliers. The objective is to enable a building management system to be used for detection of abnormal energy use. First, we framed the issue of energy performance indicators, and how they feed into data visualization (Data Viz) tools for a large building stock, especially for university campuses. Both for Data Viz and clustering algorithm processes, we discussed two possible approaches to choose the right number of clusters and the identification of alert thresholds and outliers, after a brief presentation of the University of Turin's building stock case study. Different Data Viz tools have been studied to apply a specific clustering algorithm, the k-means one. An explorative analysis based on the general Multidimensional detective approach by Inselberg has been performed. Two multidimensional analysis tools, the Scatter Plot Matrix and the Parallel coordinates method have been used. Secondly, the k-means clustering algorithm has been applied on the same dataset in order to test the hypothesis made during the explorative analysis. Data Viz techniques developed in this study revealed to be very useful to explore quickly and simply a large buildings' stock, identifying the worst efficient buildings and clustering them according to their distinct functions.

In this paper, a mathematical model of breast cancer governed by a system of ordinary differential equations in the presence of chemotherapy treatment and ketogenic diet is discussed. Several comprehensive mathematical analysis was carried out using varieties of analytical methods to study the stability of the breast cancer model. Also, sufficient conditions on parameter values to ensure cancer persistence in the absence of anti-cancer drugs ketogenic diet and cancer emission when anti-cancer drugs, immune-booster, ketogenic diet are included were established. Furthermore, optimal control theory is applied to find out the optimal drug adjustment as an input control of the system therapies to minimize the number of cancerous cells by considering different controlled combinations of administering the chemotherapy agent and ketogenic diet using the popular Pontryagin’s Maximum Principle. Numerical simulations were presented to validate our theoretical results.

This article presents a methodology to process information from a Terrestrial Laser Scanner (TLS) from three dimensions (3D) to two dimensions (2D), and to two dimensions with a color value (2.5D), as a tool to document and analyze heritage buildings. Principally focused on the loss of material in stone, this study aims at creating an evaluation method for loss control, taking into account the state of conservation of the building in terms of restoration, from studying the pathologies, to their identification and delimitation. A case study on the Cathedral of the Seu Vella de Lleida was completed, examining the details of the stone surfaces. This cathedral was affected by military use, periods of abandonment, and periodic restorations.

Emerging countries in Southeast Asia are facing considerable challenges in addressing rising motorisation and its negative impact on air quality, traffic, energy security, liveability, and greenhouse gas emissions. Indeed, even as initial policies to address these issues are being agreed and implemented, current trends are incompatible with sustainable development and long-term climate change targets. This paper presents a comparative analysis of the approach and status of sustainable, low-carbon transport policy in ASEAN countries and identifies differences and similarities, with the aim of helping assessment of feasibility of future policies and informing future studies on policy innovations and cross-country learning. The methodology is based on the taxonomy of policy components developed by Howlett and Cashore, and our data on comprehensive country studies for Indonesia, the Philippines, Thailand and Vietnam and interviews. We find that each country has a specific set of goals, objectives and targets that support sustainable transport, and, directly or indirectly, climate change mitigation. In terms of specific instruments and calibrations, which we analyse based on the Avoid-Shift-Improve approach, there are notable differences between the countries, for example in fuel economy policy.

Background: Cardiometabolic risk factors (CRFs) are significant health concerns among adults with overweight and obesity. Resistance training (RT) is known to manage CRFs, but the impact of moderate-frequency RT (two to three times weekly) remains unclear. Methods: We conducted a systematic review and meta-analysis of randomized controlled trials (RCTs) comparing moderate-frequency RT with non-exercise control or usual care in overweight and obese adults. Searches were performed in PubMed, Web of Science, EMBASE, and Cochrane Library up to February 2024, following the PRISMA 2020 guidelines. Eligible studies included non-athletic adults (BMI ≥ 25) aged 18 years or older, with RT interventions lasting 7 weeks or longer. Results: Fifteen RCTs were included. Moderate-frequency RT significantly reduced systolic blood pressure by -4.66 mmHg (95% CI -9.34 to 0.02, p=0.01) and mean arterial pressure by -6.48 mmHg (95% CI -10.63 to -2.33, p=0.002) compared to controls. Additionally, RT significantly lowered fasting insulin levels by -12.52 mmol/L (95% CI -24.17 to -0.88, p=0.04) and HOMA-IR by -1.49 (95% CI -1.63 to -1.35, p＜0.00001). Improvements were more pronounced in participants with dietary control. Conclusion: Moderate-frequency RT effectively improves CRFs in overweight and obese adults, suggesting its potential as a beneficial intervention for this population. PROSPERO registration number: CRD42022343167.

Since the outbreak of the COVID-19 pandemic, patients infected with COVID-19 may experience abnormal heart rates, posing potential health risks. This study proposes a non-contact method for measuring heart rate (HR) and heart rate variability (HRV) to effectively reduce the risk of infection and assist healthcare professionals in more accurate diagnosis and treatment. In this study, except for the different image acquisition method, other research processes and methods are similar to the research methods in [15]. The image acquisition method is changed from forehead image to palm image. The new non-contact measurement performance of the proposed method can effectively not only avoid infection concerns but also obtain heart rate and HRV quickly and conveniently, providing higher accuracy for physiological parameters, root mean square error (RMSE), and mean absolute percentage error (MAPE) compared to those in recently published papers.

Background and objectives: As the oblique lateral interbody fusion at L5/S1 (OLIF51) and lateral corridor approach (LCA) have gained popularity, the understanding of precise vascular structure at L5/S1 level is indispensable. The objectives of this study were to investigate the vascular anatomy at L5/S1 level, and to compare the movement of vascular tissue between supine and lateral decubitus position using the intraoperative enhanced CT and MRI. Materials and Methods: A total of 43 patients who underwent either OLIF51 or LCA were investigated with the average age at surgery of 60.4 (37-80) years old. The preoperative MRI was taken to observe axial and sagittal anatomy of vascular position under supine position. The intraoperative vein-enhanced CT was taken just before incision in the right decubitus position, and compared to supine MRI anatomy. The iliolumbar vein appearance and its types were also classified. Results: The average vascular window allowed for OLIF51 was 22.8 mm and 34.1 mm at either L5 caudal endplate or S1 cephalad endplate level, respectively. It allowed for LCA was 14.2 mm and 12.6 mm at either level, respectively. The left common iliac vein moved 3.8 mm and 6.9 mm to right direction at either level from supine to right decubitus position, respectively. The bifurcation moved 6.3 mm to caudal direction from supine to right decubitus. The iliolumbar vein was located at 31 mm lateral from midline, and MRI detection rate was 52%. Conclusions: The precise measurement of vascular anatomy indicated that OLIF51 approach was the standard minimally invasive anterior approach for L5/S1 disc level compared to LCA, however, there were many variations in quantitative anatomy as well as significant vascular movements between supine and right decubitus position. In the clinical setting of OLIF51 and LCA surgeries, the careful preoperative evaluation and intraoperative 3D imaging are recommended for the safe and accurate surgery.

Folk residence in the cold region of Northeast China is an important part of China's traditional folk residence, with significant geographical representation. In this paper, we take the residential compounds of villages and towns in the cold region of Northeast China as the research object, summarize four typical layout forms of residential compounds of villages and towns in the cold region of Northeast China, simulate the wind environment of compounds of different layout forms in winter by using the computer numerical simulation software Fluent, and then analyze and evaluate the wind environment of compounds by combining with the evaluation standard of wind speed ratio and considering the area of wind shadows, number of vortices and other factors.

In the current industrial revolution, advanced technologies and methods can be effectively utilized for the detection and verification of defects in high-speed steel filament production. This paper introduces an innovative methodology for the precise detection and verification of micro surface defects found in steel filaments through the application of the Eddy current principle. Permanent magnets are employed to generates a magnetic field with high frequency surrounding a coil of sensor positioned at the filament's output end. The sensor's capacity to detect defects is validated through a meticulous rewinding process, followed by a thorough analysis involving scanning electron microscopy (SEM) and energy-dispersive spectroscopy (EDS). Artificial defects were intentionally introduced into a sample, and their amplitudes were monitored to establish a threshold value. The amplitude signal of these created defect was identified at approximately 10% FSH, which corresponds to a crack depth of about 20 µm. In the experimental production of 182 samples covering 38 km, the defect ratio was notably high, standing at 26.37%. These defects appeared randomly along the length of the samples. The verification results underscore the exceptional precision achieved in the detection of micro surface defects within steel filaments. These defects were primarily characterized by longitudinal scratches and inclusions containing physical tungsten carbide.

To utilize heterosis and combining ability for grain yield and its attributing traits along with three physiological traits viz., leaf area index, chlorophyll fluorescence and chlorophyll content in bread wheat (Tritium aestivum L.) the crosses were attempted during rabi, 2019-20 in a half diallel mating scheme among 8 wheat varieties and the study was carried out during rabi, 2020-21 at Block No. D-13 field of Mahua block, Simradha research farm, Rani Lakshmi Bai Central Agricultural University, Jhansi. Analysis of variance showed significant differences for treatments. Based on per se performance the hybrids NW 5054 x PBW 723 (23.3 g), and HI 1544 x NIAW 34 (23.14 g), were identified for the higher grain yield. The hybrid HI 544 x NIAW 34 (18.41 %) was identified as the best heterotic cross for grain yield per plant and its component traits. The hybrids HI 1544 x NIAW 34 (3.40) and HI 1544 x GW 322 (2.76), as well as the parents HD 3086 (21.85) and PBW 723 (20.68), were identified as superior economic hybrids and parents based on SCA/GCA effects, per se performance for grain yield per plant, and its component trait in bread wheat. Days to heading, flag leaf length, biological yield per plant, harvest index, number of grains per spike, 1000 grain weight, spike length, leaf area index, chlorophyll fluorescence, and chlorophyll content were all positively correlated with grain yield per plant.

Background: Swimming and, specifically, front crawl, can be included among the "overhead" sports. Overhead sports are a risk factor for some problems of the musculoskeletal system, especially the shoulder. The aim of the study was assessing the incidence of shoulder and neck pain in a Masters Swimming Team and its correlation with the crawl stroke. Methods: It is an observational study through video-analysis of the stroke and a questionnaire. The participants are 61 athletes of a Master team, whose prevailing training stroke was the front crawl were selected for the present study. Their stroke was analyzed during training by a go-pro camera mounted on a sliding trolley on a track, evaluating with their trainer their technical defects. A questionnaire about frequency of shoulder and neck pain during the last five years was administered to all the participants at the study. Results: From the questionnaire, 45 and 55 out of 61 athletes had suffered from shoulder pain and cervical pain, respectively. Both types of pain were correlated with the weekly swimming volume. The swimmers with hyperflexion of the wrist and prolonged internal rotation in the pulling phase had shoulder problems. Those who suffered from current shoulder pain reduced the underwater time. The four swimmers with an excessive body roll during breathing and those who kept their heads extended, reported cervical pain. Conclusions: Shoulder and neck pain could be prevented with the correction of specific technical errors in crawl stroke.

Background: The clinical impact of vasopressin in hemorrhagic shock remains largely unknown. Objective: This systematic review and meta-analysis was designed to investigate the effects of vasopressin receptor agonists during the resuscitation of hemorrhagic shock. Methods: A systematic search of PubMed (MEDLINE), Scopus, and PubMed Central was conducted for relevant articles. Preclinical (animal) and clinical studies were included. The primary objective was to investigate the correlation of vasopressin receptor agonist use with mortality and various hemodynamic parameters. Results: Data extraction was possible in 13 animal studies and two clinical studies. Differences in risk of mortality between patients who received a vasopressin receptor agonist were not statistically significant when compared to those who were not treated with such agents [RR (95%CI): 1.17 (0.67, 2.08); p=0.562; I2 = 50%]. The available data were insufficient to conduct a meta-analysis assessing the effect of vasopressin receptor agonists on hemodynamics. Drawing safe conclusions from animal studies was challenging, due to significant heterogeneity in terms of species and dosage of vasopressin receptor agonists across studies. Conclusions: Differences in risk of mortality between patients who received a vasopressin receptor agonist were not statistically significant when compared to those who were not treated with such agents after hemorrhagic shock.

This paper focuses on quantifying the economic and financial viability of NB-IoT and LoRaWAN technologies, two low-power wide-area network (LPWAN) technologies with unique characteristics that make them suitable for IoT applications. The purpose of the study is to propose an artefact for performing life cycle cost analysis and demonstrate its application to these technologies. The methodology uses pragmatic computational tools to facilitate the analysis and considers all relevant economic and financial factors, such as operating costs, equipment costs, and revenue potential. The main finding of the study is that NB-IoT and LoRaWAN technologies have different cost structures and revenue potentials, which may affect their economic and financial viability for different IoT applications. Ultimately, the study concludes that a comprehensive life cycle cost analysis is critical to making informed decisions about technology adoption, and that the proposed methodology can be applied to other IoT technologies to gain insight into their economic and financial viability.

Morphological features and composition of ISSR DNA fragments were studied in species of the genus Tulipa L. A comparative analysis of the data obtained was carried out and an attempt was made to clarify the species belonging of plants. Plants obtained from various sources were studied. It was found that representatives of the genus Tulipa L. from the two subgenera Tulipa and Eriostemones are well separated not only morphologically, but also by the composition of ISSR fragments. At the intra- and interspecific level, the results for morphological traits and molecular data differed. Interspecific and intraspecific differences were more clearly traced in the complex analysis of morphological features and ISSR PCR data. All samples obtained in the form of bulbs and renewed vegetatively had an identical set of ISSR fragments. Plants grown from seeds were characterized by a significant variety of molecular markers and had both species-specific and in-dividual genetic variability. It was found that the samples obtained and registered as the Tulipa urumiensis Stapf are the yellow-flowered form of the Tulipa tarda Stapf, and a sample received as the Tulipa turkestanika Regel is the Tulipa bifloriformis Vved. Thus, a comprehensive study of both the data of fragmentary DNA analysis and morphological features, provided a sufficient number of DNA samples, makes it possible to clarify the species of tulip plants, and also allows us to assess the genetic diversity of the genus Tulipa.

Background and Aim: Spontaneous bacterial peritonitis is a common infection in liver cirrhosis. This systematic review and meta-analysis provides detailed information on the prevalence of SBP among HBV and HCV-related liver cirrhosis globally. Methods: A systematic search for articles describing the prevalence of SBP in HBV, and HCV related cirrhosis was conducted following the Preferred Reporting Items for Systematic Reviews and Meta-analysis (PRISMA) guidelines. Our search returned ten (10) eligible articles involving 1,713 viral cirrhosis cases representing eight (8) countries. A meta-analysis was performed on our eligible studies using the random effect model. A protocol was registered with PROSPERO (CRD42022321790). Results: The pooled prevalence of SBP in HBV associated cirrhosis had the highest estimate [8.0% (95% CI, 2.7 – 21.0%; I2= 96.13%; p < 0.001)], followed by SBP in HCV associated liver cirrhosis [4.0% (95% CI, 1.3% – 11.5%; I2 = 88.99%; p < 0.001)]. China (61.8%, CI: 57.1 – 66.3%), the USA (50.0%, CI: 34.6 – 65.4%), and Holland (31.1%, CI: 21.6 – 42.5%) had the highest estimate for SBP in HBV associated liver cirrhosis, SBP in HCV associated liver cirrhosis and SBP in HBV+HCV associated liver cirrhosis respectively. There was a significant difference in the prevalence of SBP in viral hepatitis-associated liver cirrhosis with the year of sampling and method of SBP detection at P<0.001. There was an increase in SBP incidence at the beginning of 2016 across the liver cirrhosis in this study. Conclusion: The findings of this review revealed an increase in the incidence of SBP in viral hepatitis over the last decade, the latter could be due to the global increase in Bacterial resistance. This indicates a possible future rise in the global prevalence of SBP among HBV, and HCV-related liver cirrhosis.

Big data has revolutionised science and technology leading to the transformation of our societies. High Performance Computing (HPC) provides the necessary computational power for big data analysis using artificial intelligence and methods. Traditionally HPC and big data had focused on different problem domains and had grown into two different ecosystems. Efforts have been underway for the last few years on bringing the best of both paradigms into HPC and big converged architectures. Designing HPC and big data converged systems is a hard task requiring careful placement of data, analytics, and other computational tasks such that the desired performance is achieved with the least amount of resources. Energy efficiency has become the biggest hurdle in the realisation of HPC, big data, and converged systems capable of delivering exascale and beyond performance. Data locality is a key parameter of HPDA system design as moving even a byte costs heavily both in time and energy with an increase in the size of the system. Performance in terms of time and energy are the most important factors for users, particularly energy, due to it being the major hurdle in high performance system design and the increasing focus on green energy systems due to environmental sustainability. Data locality is a broad term that encapsulates different aspects including bringing computations to data, minimizing data movement by efficient exploitation of cache hierarchies, reducing intra- and inter-node communications, locality-aware process and thread mapping, and in-situ and in-transit data analysis. This paper provides an extensive review of the cutting-edge on data locality in HPC, big data, and converged systems. We review the literature on data locality in HPC, big data, and converged environments and discuss challenges, opportunities, and future directions. Subsequently, using the knowledge gained from this extensive review, we propose a system architecture for future HPC and big data converged systems. To the best of our knowledge, there is no such review on data locality in converged HPC and big data systems.

In this work, we have proposed two new methods for the synthesis of [TcO2L4]+ (where L = im-idazole (Im), methylimidazole (MeIm)) complexes using thiourea (Tu) and Sn(II) as reducing agents. The main and by-products of the reactions were determined, and possible reaction mechanisms were proposed. We have shown that the reduction of Tc(VII) with thiourea is ac-companied by the formation of the Tc(III) intermediate and further oxidation to Tc(V). The reac-tion conditions changing can lead to the formation of Tc(VII) and Tc(IV) salts. Seven new crystal structures are described in this work: Tc(V) complexes, salts with Tc(VII) and Tc(IV) anions. For halide salts of Tu the cell parameters were determined. In all obtained compounds, except for [TcO2(MeIm)4]TcO4, there are π-stacking interactions between aromatic rings. An increase in the anion size lead to weaken intermolecular interactions. Halogen bonds and anion-π interactions have also been found in hexahalide-containing compounds. The Hirshfeld surface analysis showed that the main contribution to the crystal packing is made by van der Waals interactions of the H···H type (42.5–55.1%), H···C/C ···H (17.7–21.3%) and hydrogen bonds, which contribute 15.7–25.3% in total.

Background: It has been demonstrated that pressotherapy used post-exercise (Po-E) can influence training performance, recovery, and physiological properties. This study examined the effec-tiveness of pressotherapy on these parameters. Methods: The systematic review and meta-analysis were performed according to PRISMA guidelines. A literature search of MEDLINE, PubMed, EBSCO, Web of Science, SPORTDiscus and ClinicalTrials has been done up to March 2021. Inclusion criteria were: randomized control trials (RCTs) or cross-over studies, mean participant age be-tween 18-65 yrs., ≥ 1 exercise mechanical pressotherapy intervention. The risk of bias was assessed by the Cochrane risk-of-bias tool for RCT (RoB 2.0). Results: 12 studies comprised of 322 partici-pants have been selected. The mean sample size was n = 25. Pressotherapy significantly reduce muscle soreness(Standard Mean Difference;SMD= -0.33; CI = -0.49, -0.18; p < 0.0001; I2 = 7%). Pres-sotherapy did not significantly affect jump height (SMD = -0.04; CI =-0.36, -0.29; p = 0.82). Presso-therapy did not significantly affect creatine kinase level 24-96h after DOMS induction (SMD = 0.41; CI = -0.07, 0.89; p = 0.09; I2 = 63%). Conclusions: Only moderate benefits of using pressotherapy as a recovery intervention have been observed. Results varied between the type of exercise and used protocol. Pressotherapy should only be applied as an additional component of a more compre-hensive recovery strategy. Study PROSPERO registration number- CRD42020189382.

The Connor–Davidson Resilience Scale (CD-RISC) and the Brief Resilience Scale (BRS) are two widely used scales to measure resilience. Although both scales seek to assess an individual’s ability to recover from and adapt to disruptions or stressful events, they may capture different aspects of resilience. While the CD-RISC focuses on resources that can help individuals recover from and adapt to disruptions or stressful events, the BRS directly measures one’s ability to bounce back or be resilient. The aim of this study is to empirically examine the differences between the CD-RISC and the BRS. Two samples (n = 202, 246) consisting of undergraduate students from Taiwan were used. The results of confirmatory factor analysis show that the CD-RISC and the BRS are highly correlated but still distinct. The results of regression analyses show that the CD-RISC and the BRS have unique predictive effects on depression and life satisfaction. The research findings suggest that the CD-RISC and the BRS capture different aspects of resilience. For future research on resilience, researchers should pay attention to the differences between these scales and choose the one that most closely fits their research purpose.

The origin of the man at the Earth is directly associated with the determination of directions of the flow distribution of the ancient man migration to adjacent territories. In such studies traditionally mainly landscape and climatological changes are considered. We suggest that along with the above factors, regional tectonic-geodynamic factors played a dominant role in the character of migration. The considered African-Levantine-Caucasian region is one of the most complex regions of the world, where collisional and spreading processes of geodynamics converge. First is determined an essential influence of the Akchagylian hydrospheric maximum (about 200 m above the mean sea level) limiting the ancient men migration from Africa to Eurasia. We propose that the Levantine Corridor emerged after the end of the Akchagylian transgression and landscape forming in the Eastern Mediterranean. This corridor location was formed by the movements between the Dead Sea Transform and the boundary of the carbonate platform of the Mesozoic Terrane Belt. Further landscape evolution was largely determined by the geodynamic behavior of the deep mantle rotating structure occurring below the central part of the region under study. All the mentioned events around and in the Levantine Corridor have been studied in detail on the basis of the combined geodynamic, paleogeographic, and paleomagnetic analyzes performed in northern Israel (Carmel uplift and Galilee plateau). Careful studies of the Evron quarry geological section indicate that it is a unique one for the dating of the marine and continental archaeological sequences and sheds light on the movement of the ancient man along the Levantine Corridor.

The purpose of this study is to examine the relationship between the institutional investors which can affect financial performance for corporate sustainability on the income smoothing. Therefore, this study focus on the connection between the nature of stock rights and income smoothing in China. For this study, hypotheses were established on the relationship each state-controlled companies, income smoothing, and information equilibrium of individual investors, and empirical analysis was conducted through related variables. The analysis results are summarized in three categories as follows. First, this research finds that state-controlled firms (CONTs) prefer income smoothing activities compared to non-state-controlled firms for the long-term sustainable development of firms using data from 2011 to 2019. Second, this study found out that Institutional investors support the behavior of CONTs to smooth their earnings because this behavior is seen as an attempt by CONTs to convey valuable private information to other investors. Third, we was able to discover that institutional investors' monitoring effect is predominantly driven by pressure-resistant institutional investors. This research complements the lack of empirical research on income smoothing and enable to give a guideline that the type of stock rights is a critical key determinant of participation in income smoothing activities for stable growth and sustainability in the future.

Complex modeling has received significant attention in recent years and is increasingly used to explain the statistical phenomenon with increasing and decreasing fluctuations such as the similarity or difference of spike protein charge patterns of coronaviruses. Different from the existing covariance or correlation coefficient methods in traditional integer dimension construction, this study proposes a simplified novel fractional dimension derivation with the exact Excel tool algorithm. It involves the fractional center moment extension to covariance, which ends up a complex covariance coefficient that is better than the Pearson correlation coefficient, in the sense that the nonlinearity relationship can be further depicted. The spike protein sequences of coronaviruses were obtained from the GenBank and GISAID database, including the coronaviruses from pangolin, bat, canine, swine (three variants), feline, tiger, SARS-CoV-1, MERS, and SARS-CoV-2 (including the strains of Wuhan, Beijing, New York, German, and UK variant B.1.1.7) were used as the representative examples in this study. By examining the values above and below the average/mean based on the positive and negative charge patterns of the amino acid residues of the spike proteins from coronaviruses, the proposed algorithm provides deep insights into the nonlinear evolving trends of spike proteins for understanding the viral evolution and identifying the protein characteristics associated with viral fatality. The calculation results demonstrate that the complex covariance coefficient analyzed by this algorithm is capable of distinguishing the subtle nonlinear differences in the spike protein charge patterns with reference to Wuhan strain SARS-CoV-2 for which the Pearson correlation coefficient may overlook. Our analysis reveals the unique convergent (positive correlative) to divergent (negative correlative) domain center positions of each virus. The convergent or conserved region may be critical to the viral stability or viability; while the divergent region is highly variable between coronaviruses suggesting high frequency of mutations in this region. The analyses show that the conserved center region of SARS-CoV-1 spike protein is located at amino acid residues 900, but shifted to the amino acid residues 700 in MERS spike protein, and then to amino acid residues 600 in SARS-COV-2 spike protein, indicating the evolvement of the coronaviruses. Interestingly, the conserved center region of the spike protein in SARS-COV-2 variant B.1.1.7 shifted back to amino acid residues 700, suggesting this variant is more virulent than the original SARS-COV-2 strain. Another important characteristic our study reveals is that the distance between the divergent mean and the maximal divergent point in each of the viruses (MERS>SARS-CoV-1>SARS-CoV-2) is proportional to viral fatality rate. This algorithm may help to understand and analyze the evolving trends and critical characteristics of SARS-COV-2 variants, other coronaviral proteins and viruses.

Ostreococcus tauri is a simple unicellular green alga representing an ecologically important group of phytoplankton in oceans worldwide. Modern molecular techniques must be developed in order to understand the mechanisms that permit adaptation of microalgae to their environment. We present for the first time in O. tauri a detailed characterization of individual genomic integration events of foreign DNA of plasmid origin after PEG-mediated transformation. Vector integration appears to be random, occurring mainly at a single locus, and thus confirming the utility of this technique for insertional mutagenesis. While the mechanism of double-stranded DNA repair in the O. tauri model remains to be elucidated, we clearly demonstrate by genome resequencing that the integration of the vector leads to frequent structural variations (deletions/insertions and duplications) and some chromosomal rearrangements in the genome at the insertion loci, and often within the vector sequence itself. From these observations, we speculate that a non-homologous end joining-like mechanism is required during random insertion events, as described in plants and other freshwater algal models. PEG-mediated transformation is therefore a promising molecular biology tool, not only for functional genomic studies, but also for biotechnological research in ecologically important marine algae.

Acetylcholine (ACh) is one of the best characterized neurotransmitters. Its central roles in the cholinergic areas and central nervous system (CNS) and peripheral (PNS) synapses are well known. It was the first molecule identified as a neurotransmitter and appears to be phylogenetically one of the oldest signaling molecules. In fact, ACh was detected in bacteria, protozoa, fungi, algae and primitive plants, indicating that the cholinergic system was widely distributed in living organisms before its appearance in the nervous system. The autonomous nervous system (ANS) is an integral part animal kingdom history. It determines fight-escape reactions as well as outlining the vital and cognitive functions bio-organization rhythms. The virus (Covid-19) extraneous effects acting on it could help to better understand its functions. Through a new deductive and inductive the path axioms are developed and an absurd hypothesis, "natural genetic recombination between different species" is put forward, trying to verify a correlation, tracing what could be the genesis, the "zero-point", crucial and fundamental moment. A positive correlation with different toxins is obtained and the double pathogenic mechanism of Covid-19 theory is proposed. The process allows us to outline the possibility about toxic-like factors presence.

Introduction: The 2019 novel coronavirus (COVID-19) is very contagious, and can be transmitted to other people by droplet, aerosol, sneezing, infected surface, and cough. There is no vaccine or effective treatment at this time. Therefore, the prevention of COVID-19 and the rapid diagnosis of infected patients is crucial. Method: We searched all relevant literature published up to February 28, 2020, from Embase, Scopus, PubMed, Web of Science, and the Cochrane library to collect the studies that reported clinical and laboratory characteristics of COVID-19 infected patients. The study quality was assessed with the Critical Appraisal Checklist. Depending on the heterogeneity test, we used either random or fixed-effect models to analyze the appropriateness of the pooled results. Result: Twenty studies were included in the meta-analysis, including a total of 52,251 patients with confirmed COVID-19 infection. 69.5% (95% CI 54.5-81, p < 0.001) of patients had a history of recent travel to Wuhan, contact with people from Wuhan, or lived in Wuhan. The most common symptoms among COVID-19 infected patients were fever 85.6 % (95% CI 73 -93, p < 0.001), and cough 63 % (95% CI 55.5-70, p < 0.001), respectively. The laboratory analysis showed that thrombocytosis was present in 91% (95% CI 81-98, p < 0.001) CRP was elevated in 81% (95% CI 65-91, p < 0.001), and lymphopenia in 62.5% of cases (95% CI 42-79, p < 0.001). The most common radiographic signs were bilateral involvement in 76.8% (95% CI 62.5-87, p < 0.001) and consolidation in 75.5% (95% CI 50.5-91, p < 0.001) of patients. Most patients (85.4%) were hospitalized, 20.6% of patients were admitted to the ICU in critical condition, and the mortality rate was 5.6%. Conclusions: Fever and cough are the most common symptoms of COVID-19 infection in the literature published to date. Thombocytosis, lymphopenia, and increased CRP were common lab findings although most patients included in the overall analysis did not have laboratory values reported. The most common radiographic sign was bilateral involvement in and consolidation. Among Chinese patients with COVID-19, rates of hospitalization, critical condition, and hospitalization were high in this study, but these findings may be biased by reporting only confirmed cases.

Flower color and color patterns are important traits for ornamental species; for this reason, a comprehensive understanding of the genetic mechanisms underlying these characters is extremely significant for plant breeders. The tulip tree (Liriodendron tulipifera Linn.) is well known for its flowers, odd leaves and tree form. However, the genetic mechanism underlying its flower color remains unknown. In this study, a putative LtuPTOX gene was identified based on multiple databases of differential transcript expression at various developmental stages and the complete genome sequence of Liriodendron. Then, the full-length cDNA of LtuPTOX was derived from tepals and leaves using RACE approaches. Furthermore, the gene structure and a phylogenetic analysis of PTOX as well as AOXs, highly similar homologs in the AOX family, were used to distinguish between the two subfamilies of genes. In addition, transient transformation and qPCR methods were used to determine the subcellular localization and tissue expression pattern of the LtuPTOX gene. Moreover, the expression of LtuPTOX as well as pigment contents was investigated to illustrate the function of this gene during the formation of orange bands on petals. The results showed that the LtuPTOX gene encodes a 358-aa protein that contains a complete AOX domain (PF01768.17). Accordingly, Liriodendron PTOX and AOX genes were identified as only paralogs since they were rather similar in the sequence. LtuPTOX showed chloroplast localization, and expressed in the colored organs such as petals and leaves. In addition, increasing pattern of LtuPTOX transcripts lead to carotenoids accumulation on the orange-band in the development period of flower bud. Taken together, our results provide that LtuPTOX is involved in petal carotenoid metabolism and orange band formation in L. tulipifera. Meanwhile, the identification of this potentially involved gene will lay a foundation for further uncovering the mechanism of flower color formation in L. tulipifera.

The aim of this study was to examine pathologic complete response (pCR) and overall survival (OS) of patients diagnosed with non-metastatic inflammatory breast cancer (IBC). A total of N=8,550 cases undergoing surgery were identified between 2004-2013, using the National Cancer Database (NCDB). Patients were grouped into 4 biologic subtypes (HR+/HER2-, HR+/HER2+, HR-/HER2+, HR-/HER2-). The median age at diagnosis was 56 years. On average, women were followed for 3.7 years [interquartile range=3.0]. The majority were white (80%), had private health insurance (50%), and presented with poorly differentiated tumors (57%). Approximately 46% of the cancers were >5cm. Most patients underwent mastectomy (94%) and received radiotherapy (71%). Differences by biologic subtypes were observed for grade, lymph node invasion, race, and tumor size (p<.0001). Compared with non-pCR (54%), patients experiencing pCR had superior 5-year survival (77%) (p<.0001). Survival was poor for triple-negative (TN) tumors (37%) vs. other biologic subtypes (60%) (p<.0001). On multivariable analysis, TN-IBC, positive margins, and not receiving either chemotherapy, hormonal therapy or radiotherapy were independently associated with poor 5-year survival (p<.0001). In this large multicentric analysis of IBC, categorized by biologic subtypes, we observed significant differential tumor, patient and treatment characteristics, and OS.

Soups show diverse health functions, which should be related with their nutrient profiles. NMR spectroscopy is a robust, sensitive and rapid method to unveil or identify the chemical composition of food or food-derived metabolites. In the current study, 1H-NMR spectroscopy approach was applied to identify the metabolic profiling of two kinds of home-cooked freshwater fish soups (crucian carp and snakehead fish) before and after in vitro gastrointestinal digestion. The nutritional profiles of these two kinds of soups were identified at first. With the help of OPLS-DA method (Orthogonal Partial Least Squares Discriminant Analysis), these two different kinds freshwater fish under different states were completely discriminated. The metabolites changes in digested fish soups could reveal the information of chemical compounds which play important roles in the body. Furthermore, the metabolic patterns of different kinds of fish soups could reflect the various nutrition profiling characteristics for dietary therapy.

It is well known that working PV plants show several maintenance needs due to wiring and modules degradation, mismatches, dust and PV cells defects and faults. There are a wide range of studies that show the theoretical and some laboratory tests of how these circumstances may affect the PV production. Thus, it results mandatory to evaluate the whole PV plant performance and, then, it’s payback time, profitability and environmental impact or carbon footprint. However, very few studies include a systematic procedure to quantify and supervise the real degradation effects and faults impacts on the field. In this paper, the authors first conduct a brief review of the most frequent PV faults and degradation that can be found on real conditions operative PV Plants. Then, they propose and develop an innovative Geographic Information System application to locate and supervise them. The designed tool has been applied to either a large PV plant of 108 kWp and a small PV plant of just 9 kWp installed on a home rooftop. For the large PV plant, 24 strings of PV modules have been modelized and introduced into the GIS application and every module in the power plant has been studied including voltage, current, power, series and parallel resistance, fill factor, normalized PV curve to STC, thermography and visual analysis. For the small PV installation 3 strings of PV panels have been studied identically. It must be noticed that PV modules in this case include power optimizers. The precision of the study allows the researchers to locate and supervise up to a third part of every PV cell in the system, which are adequately georreferenciated. The developed tool allows both the researchers and the investors to increase control on the PV plant performance and conducts to a better planification of maintenance actuations and to evaluate several PV modules replacement strategies in a preventive maintenance programme. Found PV faults include hot spots, snail tracks, EVA discoloration, PV cells fractures, busbars discoloration, bubbles and Si discoloration.

Acoustic Radiation Forced Impulse (ARFI) is an ultrasound integrated method, measuring stiff-ness by point shear wave elastography. To evaluate the diagnostic performance of ARFI of the liver and of the spleen, combined with spleen dimension and platelet count, in predicting clinical events in cirrhosis, a prospective and cross-sectional study was conducted between February 2017 and February 2021. The following ratio scores with ARFI measurements were performed: ALSDP (ARFI Liver-Spleen Diameter-to-Platelets ratio score), ASSDP (ARFI Spleen-Spleen Diam-eter-to-Platelets ratio score), ASSAP (ARFI Spleen-Spleen Area-to-Platelets ratio score), ALSAP (ARFI Liver-Spleen Area-to-Platelets ratio score). In 100 enrolled subjects, spleen ARFI, ASSDP, ASSAP, were significantly associated with high-risk oesophageal varices (HRVs) in the prospec-tive short- and long-term follow-up and in the cross-sectional study (p 0.7). ARFI-ratio scores can predict, in cirrhotic patients, the risk of developing HVRs in short and long-term period.

This study checked whether vitamin D (Vit-D) supplementation improves the efficacy of resistance training (RT) in terms of increasing muscle strength and lean body mass (LBM) and influencing cardiorespiratory fitness (VO2max) in Vit-D insufficient middle-aged healthy men. Participants (n = 28) were quasi‐randomly assigned to one of the two groups, which, in a double‐blind manner, supplemented their diet daily with either Vit‐D (8000 IU; VD) or placebo (PLC) during participation in a 12‐week supervised RT program. During the intervention, serum Vit‐D concentrations increased 2.6‐fold (p < 0.001) in the VD group, while no changes occurred in the PLC group. Muscle strength gains (p < 0.001) as measured in seven exercises performed on RT equipment and increases (p < 0.001) in LBM were similar in the two groups. Total fat mass, percent total fat, and percent android fat decreased (p < 0.05) to a similar extent in both groups, but there was no change in VO2max in either group. In conclusion, in healthy Vit‐D insufficient middle-aged men engaged in resistance training, Vit‐D supplementation increases serum 25(OH)D levels but does not enhance gains in muscle strength and LBM or decreases in fat mass and fat percentage and does not affect cardiorespiratory fitness.

The main purpose of our research is the evaluation of the efficacity of solvent polarity on phenolic composition, as well as the antibacterial, and antioxidant activities of extract of Moroccan Mentha aquatica L., leaves. To attempt these objectives, the HPLC-DAD was used to identify the biomolecules. The total amount of phenolic and flavonoid content was determined using the Folin-Ciocalteu and aluminum trichloride processes as well as the DPPH, RP, and TAC tests were used to evaluate the antioxidant capabilities. In addition, by employing both in vitro and in silico analysis through the microdilution method, the minimum inhibitory concentration (MIC) and minimum bactericidal concentration (MBC) of the extracts were assessed against multidrug-resistant bacteria. Furthermore, the High-Performance Liquid Chromatography (HPLC) analysis indicated that all extracts of M. aquatica were abundant in noteworthy phytochemical compounds, especially gallic acid, vanillic acid, chlorobenzoic acid, quercetin, and kaempferol. Furthermore, the results indicated that the total phenolic content was higher in hydroethanolic extract (62.19 ± 1.19 mg GAE/g DW) in contrast to the acetonic and aqueous extracts (22.22 ± 0.64, and 22.44± 0.57 mg GAE/g DW) respectively. Similarly, the aqueous ethanol extract contained the greatest flavonoid concentration, with values of 29.15± 0.09 mg QE/g DW when compared with the other extracts. The seam extract poses excellent antioxidant power with an IC50 of 0.06 ± 0.00 mg/mL for the DPPH test, and lower RP with EC50 of 80± 0.00 µg/ml when compared with acetonic and aqueous extract (370± 0.00 and 460± 0.01 µg/mL) respectively. Moreover, the hydroethanolic extract has a high level of TAC 75.09± 2.00 mg EAA/g DW, followed by aqueous extract carrying a value of 28.53 ± 1.36 mg EAA/g DW. The antibacterial capacity is ranged between 0.78 ± 0.05 mg/mL and 12.60 ± 0.00 mg/L. The results of the in-silico study demonstrated that quercetin, vanillic acid, and naringenin components contribute to the antioxidant capability. While gallic acid, kaempferol, and quercetin components are attributed to the antibacterial capacity.

Currently, one of the main challenges is the mitigation of the effects of climate change on the agricultural sector. Conventional agriculture, with the intensive use of herbicides and pesticides to control weeds and pests, and the improper use of mineral fertilizers, contributes to climate change by causing increased greenhouse gases and groundwater pollution. Therefore, more innovative technologies must be used to overcome these problems. One possible solution is nanotechnology, which has the potential to revolutionize the conventional agricultural system. Active nanoparticles can be used both as a direct source of micronutrients and as a delivery platform for bioactive agrochemicals to improve crop growth, yield and quality. The use of nanoparticle formulations, including nanopesticides, nanoherbicides, nano-fertilizers and nano-emulsions, has been extensively studied to improve crop health and shelf life of agricultural products. Comprehensive knowledge of the interactions between plants and nanoparticles opens up new opportunities to improve cropping practices through the enhancement of properties such as disease resistance, crop yield, and nutrient use. The main objective of this review is to analyze the main effects of climate change on conventional agricultural practices, such as the use of pesticides, herbicides and fertilizers. It also focuses on how the introduction of nanoparticles into conventional practices can improve the efficiency of chemical pest control and crop nutrition. Finally, this review examines in depth the last 10 years (2014-2024) of scientific literature regarding the use of nanoparticles in agriculture to mitigate the effects of climate change.

Background: We evaluate the genetic and phenotypic features of a cohort of 12 Italian patients affected by Retinitis Pigmentosa (RP) associated with RP1 sequence variants.; Methods: Retrospective, single center study (Careggi Hospital, Florence), including a cohort of twelve Italian patients (Five male and seven female) affected by RP carrying pathogenic variants of the RP1 gene. A complete ophthalmic assessment and pedigree analysis was conducted with focus on the onset of disease symptoms, the patient’s age at the first diagnosis, the follow up duration and the possible presence of comorbidities; Results: The mean age at onset of symptoms was 31,0 ± 24,1 years old, with a mean follow-up period of 9,1± 2,4 years. The main symptoms at presentation were hemeralopia and visual field constriction. Fundus evaluation revealed a classic type of RP. Fundus autofluorescence (FAF), Optical Coherence Tomography (OCT), Electroretinogram (ERG), and visual field confirmed in most of the cases the typical features of classic retinitis pigmentosa.; (4) Conclusions: This single-center cohort of Italian patients provided information on the clinical and genetic features of RP1-associated RP. By comprehensively clarifying the genetic variations and their associated clinical manifestations, we can better tailor therapeutic interventions aimed at targeting specific genetic abnormalities. This ultimately promises to improve the prognosis and quality of life for individuals with RP-associated RP1.

The gut microbiota (GM) communicates with the brain via biochemical signaling constituting the gut-brain axis, which significantly regulates the body's physiological processes. The GM dysbiosis can impact the digestive system and the functioning of the central nervous system (CNS) linked to the onset of neurodegenerative diseases. In this review, the scientific data compiled from diverse sources primarily emphasizes the neuropathological characteristics linked to the accumulation of modified insoluble proteins (such as β-Amyloid peptides and hyperphosphorylated tau proteins) in Alzheimer’s Disease (AD) and the potential impact of gut microbiota (GM) on AD susceptibility or resilience. The specific GM profile of human beings may serve as an essential tool for preventing or progressing neurodegenerative diseases like AD. This review focuses mainly on the effect of gut microfauna on the gut-brain axis in the onset and progression of AD. The GM produces various bioactive molecules that may serve as proinflammatory or anti-inflammatory signaling, contributing directly or indirectly to the repression or progression of neurodegenerative disorders by modulating the response of the brain axis. Human studies must focus on further understanding the gut-brain axis and venture to clarify microbiota-based therapeutic strategies for AD.

Nowadays, Multi-needle electrospinning has used to be an efficient method for producing nanofiber membranes. But in the process, the fluctuation errors in electrospinning fluid flow rate have directly influence the membrane quality, which bringing instability and still have not been solved yet. For finding out the solution to the inaccurate flow control in multi-needle, it is necessary to develop a multi-stage flow runner spinneret for large-scale production of nanofiber membrane. At first, the paper uses the finite element software COMSOL to numerically simulate the polymer flow in the runner of spinneret. Based on it, the velocity field distribution curve was draw and the velocity instability coefficient of the polymer flow was attained, which are providing theoretical guidance for the optimal design of spinneret. Next, the response surface analysis method (RSM) was used to establish a regression model between the average diameter of the nanofiber membrane and the process parameters. Then, above regression model used to perform variance data processing between the average diameter and the process parameter configuration. After that, the 2D and 3D response surface profiles and the significance analysis were completed. Finally, the stability of the nanofibers production was improved, which attained the optimal adjustment of process configuration in multi-needle electrospinning.

Objectives: To assess the short-term impact of a single global stretching session on plantar pressures and lumbar range of motion (RoM) over one week in sedentary university students. Design: A randomised controlled trial with two parallel groups. Participants: Sixty-four university students were randomly assigned to a stretching group or control group. The stretching group received a single session of global stretching and the control group remained seated for the same length of time as the stretching session. Main outcome measures: Lumbar RoM and plantar pressures were assessed before, immediately after, 48 hours after, and 7 days after intervention. Results: Group-by-time interaction was significant for lumbar lateral flexion (p = 0.044), right maximal pressure (p = 0.003), left maximal pressure (p = 0.008), right mean pressure (p = 0.025), left mean pressure (p = 0.002), and maximal pressure minus mean pressure in right foot (p = 0.007). The model with plantar pressures showed a significant difference for group-by-time interaction (p = 0.010).Conclusion: Global stretching seems to counteract the ill-effects of prolonged sitting up to seven days with respect to plantar pressure in standing without improving lumbar ROM

One of the most concerning global environmental issues is the pollution of agricultural soils by heavy metals (HMs), especially cadmium (Cd), which not only affects human health by taking Cd-containing foods but also impacts the quality of rice. The soil's nitrification and denitrification processes, coupled with the release of volatile organic compounds by plants, raise substantial concerns. The understanding of three aspects of paddy soil under conditions of heavy-metal pollution and water management is currently limited. In this review, we summarized recent literature related to the deleterious effects of Cd on both soil processes related to the N cycle and rice quality, particularly aroma, in different water management practices. Under both continuous flooding (CF) and alternate wetting and drying (AWD) conditions, cadmium (Cd) has been observed to reduce both nitrification and denitrification processes. The adverse effects are more pronounced in continuous flooding (CF) compared to alternate wetting and drying (AWD). Similarly, the alteration in rice aroma is more significant in AWD than in CF. The precise modulation of volatile organic compounds (VOCs) by Cd, remains unclear based on the available literature. Nevertheless, HM accumulation is higher in AWD conditions compared to CF, leading to a detrimental impact on volatile organic compounds (VOCs). The literature concluded that AWD practices should be avoided in Cd contaminated fields to decrease accumulation and maintain the quality of rice. In the future, rhizospheric engineering and plant biotechnology can be used to decrease the transport of HMs from the soil to the plant’s edible parts.

Imprinted polymers with imprints of Zn2+ ions (ZnIP) and reference polymers without imprints (NIP) were synthesized based on humic and methacrylic acids. Comparative studies of the physical parameters of ZnIP and NIP were carried out using elemental analysis, IR spectroscopy and electron microscopy. Kinetic parameters of Zn2+ ion sorption on ZnIP and NIP were determined. It was found that the sorption kinetics on both ZnIP and NIP are approximated by a pseudo-first-order equation. The sorption rate constant for ZnIP is higher than that of NIP, indicating a higher adsorption rate of Zn2+ ions onto the surface of ZnIP. This may be due to more accessible sites on ZnIP. Adsorption of Zn2+ ions is best described by the Langmuir model, indicating monolayer adsorption on a homogeneous surface. The Langmuir model also shows that ZnIP is effective at low adsorbate concentrations. The Freundlich model describes the adsorption with less accuracy, which may indicate monolayer adsorption and less surface homogeneity. ZnIP shows better adsorption capacity and higher efficiency compared to NIP and can be proposed as a selective sorption material for Zn2+ ions.

Purpose Using Chatbots to seek healthcare information is becoming more popular. Misinformation and gaps in knowledge exist regarding the risks and benefits of Testosterone Replacement Therapy (TRT). We aimed to assess and compare the quality and readability of responses generated by four AI chatbots. Materials and Methods ChatGPT, Google Bard, Bing Chat, and Perplexity AI were asked the same eleven questions regarding Testosterone Replacement Therapy. The responses were evaluated by four reviewers using DISCERN and Patient Education Materials Assessment Tool (PEMAT) questionnaires. Readability was assessed using the Readability Scoring system v2.0 to calculate the Flesch-Kincaid Reading Ease Score (FRES) and Flesch-Kincaid Grade Level (FKGL). Kruskal-Wallis statistics were completed using GraphPad Prism V10.1.0. Results Google Bard received the highest DISCERN and PEMAT. Perplexity AI received the highest FRES and best FKGL. Significant differences were found in understandability between Bing and Google Bard, DISCERN scores between Bing and Google Bard, FRES between ChatGPT and Perplexity, and FKGL scoring between ChatGPT and Perplexity AI. Conclusion ChatGPT and Google Bard were top performers based on their quality, understandability, and actionability. Despite Perplexity scoring higher in readability, the generated text still maintained an eleventh-grade complexity. Perplexity stood out for its extensive use of citations, however, it offered repetitive answers despite the diversity of questions posed to it. Google Bard demonstrated a high level of detail in its answers, offering additional value through visual aids.

Arbutus unedo (strawberry tree) is a small Mediterranean tree capable of vigorous regrowth after disturbances like fire. Traditionally used for biomass fuel, its bark and branches hold potential for higher-value products through ecovalorisation into liquid mixtures that could replace petro-leum-based materials. This study aimed to explore the chemical composition of various compo-nents of Arbutus unedo and to produce a liquefied material from its internal (IB) and external bark (EB). Chemical compositions of internal and external bark were determined using TAPPI standards including ash, extractive content, lignin, and cellulose. Metal cations were analyzed by ICP. Liquefaction of bark was optimized in a PARR reactor, evaluating factors such as particle size, temperature, and time and the best polyols were monitored by FTIR-ATR. Polyurethane foams were made with internal and external bark liquefied materials by polymerization with isocyanate, a catalyst and water as blowing agent. Results showed that EB has a higher extractive and lignin content, while IB contains more cellu-lose. Liquefaction yields were higher for IB (74%) than EB (68%), with IB yielding polyols that produced stronger and more resilient foams. Mechanical properties of the foams were influenced by the NCO/OH ratio and catalyst levels. Overall, the internal bark demonstrated superior performance for foam production, highlighting its potential as an eco-friendly alternative to petroleum-derived materials.

Situational awareness detection and characterization of mental states have a vital role in medicine and many other fields. An electroencephalogram (EEG) is one of the most effective tools for identifying and analyzing cognitive stress. Yet, the measurement, interpretation, and classification of EEG sensors is a challenging task. This study introduces a novel machine learning-based approach to assist in evaluating situational awareness detection using EEG signals and spiking neural networks (SNNs) based on a unique spike-continuous-time-neuron (SCTN). The implemented biologically inspired SNN architecture is used for effective EEG feature extraction by applying time-frequency analysis techniques and allows adept detection and analysis of the various frequency components embedded in the different EEG sub-bands. The EEG signal undergoes encoding into spikes and is then fed into an SNN model which is well-suited to the serial sequence order of the EEG data. We utilize the SCTN-based resonator for EEG feature extraction in the frequency domain which demonstrates a high correlation with the classical FFT features. A new SCTN-based 2-D neural network is introduced for efficient EEG feature mapping aiming to achieve a spatial representation of each EEG sub-band. To validate and evaluate the performance of the proposed approach a common publicly available EEG dataset is used. Experimental results show that by using the extracted EEG frequencies features and the SCTN-based SNN classifier the mental state can be accurately classified with an average accuracy of 96.8% for the common EEG dataset. Our proposed method outperforms existing machine learning-based methods and demonstrates the advantages of using SNN for situational awareness detection and mental state classifications.

Optimal upper extremity motor control and range of motion are necessary to achieve even the basic Activities of Daily Living (ADL) function. Stroke, with resulting hemiparesis, can significantly and negatively impact an individual’s ADL function. Functional Independence Measure (FIM) self-care score can provide assessment of what aspects and to what degree ADL functions are impaired. FIM self-care assessment can also track changes in ADL function during stroke recovery and rehabilitation. Recently, sensor-acquired 3D motion analysis of stroke patients’ upper extremity has shown promise as a potential alternative to assess ADL function. This observational study evaluates whether the sensor-acquired upper extremity reachable workspace (RWS) measure correlates with clinician-evaluated FIM self-care score in stroke patients. Seventeen patients with stroke were enrolled in the study. FIM self-care, NeuroQoL upper extremity, and reachable workspace outcome measures (relative surface area, RSA) were collected upon rehabilitation hospital admission, at discharge, and at 3-month visit. Pearson and Spearman’s rank correlation coefficients as well as multiple linear regression analyses were used to determine the relationships between FIM self-care, NeuroQoL, and reachable workspace RSAs. Moderately strong correlation between total reachable workspace RSA and total FIM self-care score at discharge and at 3-month were noted (r=0.619, r=0.661, p&lt;0.05), and similarly strong correlation was also noted with the upper extremity NeuroQoL total score (r=0.690, r=0.815, p&lt;0.05). Multiple linear regression analyses revealed a change in bilateral total RSA of 0.1 unit from admission to 3-month follow up correlated with respective change in FIM self-care score of 2.011 points (95%CI: 0.663-3.360). Longitudinal improvement in ADL function during stroke rehabilitation and recovery process is correlated with improvement in reachable workspace.

This paper presents an 8x8 channel optoelectronic readout array (ORA) realized in a 180-nm CMOS process for the applications of short-range light detection and ranging (LiDAR) sensors. We propose several circuit techniques in this work including an amplitude-to-voltage (A2V) converter that reduces the notorious walk-errors by intensity compensation, and a time-to-voltage (T2V) converter that acquires the linear slope of the output signals by exploiting a charging circuit, thus extending the input dynamic range significantly from 5 uApp to 1.1 mApp, i.e. 46.8 dB. These results correspond to the maximum detection range of 8.2 meters via the action of the A2V converter and the minimum detection range of 56 centimeters with the aid of the proposed T2V converter. Optical measurements utilizing an 850-nm laser diode confirm that the proposed 8 x 8 ORA with 64 on-chip avalanche photodiodes (APDs) can successfully recover the narrow 5-ns light pulses even at the shortest distance of 56 centimeters. Hence, this work provides a potential CMOS solution for low-cost, low-power short-range LiDAR sensors.

Peri-implant infective diseases seem to be the most common cause for the late dental implant failure. Therefore, peri-implant microbiota has been intensively studied in modern implantology. Many studies showed a presence of extremely varied microflora in cases of peri-implant infective diseases. The main scope of this observational single-blind study was to analyze the presence of some microbial species in a group of patients with clinical signs of peri-implant mucositis compared to two other groups (patients treated with dental implants but without any clinical signs of peri-implant inflammation and patients treated with no dental implants). The identification of microorganisms was followed by an antibiogram in order to find their sensitivity to various antibiotics. The results showed a microbiota not necessarily specific for each situation (peri-implant infective diseases, healthy tissues around dental implants and healthy natural teeth and gums) with species like Candida albicans, Neisseria mucosa, Prevotella, Staphylococcus aureus, Streptococcus and others. Peri-implant infective diseases presented more bacterial species than other conditions.

In this study, in order to determine the effect of matrices shape on percolation threshold values, computer simulations were performed using the Monte Carlo method for a 200x200 square-shaped matrix and rectangular matrices containing the same number of nodes as the square matrix. Based on the simulations, the average values of percolation thresholds and standard deviations for current flow along and across the matrices were determined. It was determined that for a square-shaped matrix, the average values of percolation thresholds in both directions of current flow were the same. Extending the rectangular matrix while reducing its height causes the average value of the percolation threshold in the direction of current flow along the matrix to increase from 0.592740 to 0.759847, while in the transverse direction it decreases from 0.592664 to 0.403614. The values of the classical asymmetry coefficients of the probability distributions of percolation thresholds for both directions of current flow were determined. Histograms of the probability distributions of percolation threshold values for square-shaped matrix and rectangular matrices were made and compared with normal distributions. It was found that the occurrence of two percolation thresholds in rectangular layers should be considered when analyzing electrical conductivity measurements of nanocomposite thin films.

Over 3.0 billion people of the 7.75 billion globally suffer from malnutrition due to deficiencies in micronutrients, particularly iron, zinc, and vitamins (such as vitamin A, B complex, E, and folate, etc.). In response, there is growing consumer interest in foods that provide traditional nutrients and contain additional compounds beneficial to health and well-being. Wheat is the most important cereal crop in terms of both production and consumption, contributing about 30% of total cereal consumption worldwide. It provides a significant source of carbohydrates and gluten protein (around 12-14% protein), which supply substantial energy. Wheat grain is also rich in various nutrients, such as macro-elements like phosphorus (P), potassium (K), calcium (Ca), and magnesium (Mg); microelements like iron (Fe), zinc (Zn), manganese (Mn), and vitamins B complex: thiamin (B1), riboflavin (B2), niacin (B3), pantothenic acid (B5), pyridoxine (B6), biotin (B7), folate (B9), additionally soluble fiber and other trace minerals which are higher than in other major cereals. The inner bran coats, phosphates, and other mineral salts in wheat contribute to its beneficial effects on bowel movements. Despite its nutritional benefits, the quality of wheat's nutrients is a topic of ongoing discussion. Exploring ways to enhance the nutritional quality of wheat could provide valuable insights for scientists working to improve global nutrition status.

This study identified the effects of substituting fishmeal (FM) with soy protein concentrate (SPC) supplemented with lysine and methionine in the olive flounder (Paralichthys olivaceus) diet on the expression of genes related to growth, stress, immunity, and digestion. Three experimental diets were prepared; the control diet (Con) contained 60% FM, and 25% (SPC25) and 50% (SPC50) FM were replaced by SPC. After the 140-day feeding period, weight gain, specific growth rate, feed availability, biological indices and chemical composition of the muscle were not significantly affected by the dietary treatments. The gene expression levels of growth-related genes (IGF, GFB-3), immune-related genes (IL-8 and caspase), stress-related genes (SOD, GPX, PRX, TRX) were higher in Con fish than in those fed the SPC25 and SPC50 diets. Chymo-TRY2, TRY2 and TRY3 in the stomach of fish fed the SPC25 diet were higher than fish fed the Con or SPC50 diets. TRY2 and lipase of fish fed the SPC25 diet were higher than those of fish fed the other diets but TRY3 was not significantly affected by the treatments in the intestine. In conclusion, substituting 25% FM with SPC was the most effective for the expression of growth, immune, stress, and digestive enzyme genes.

After decades of studies, the pathogenesis of Autism Spectrum Disorder (ASD) remains unclear and there still lackseffective treatment strategies for core symptoms. Our recent work, combined with others’ research in a diversity ofmodels and clinical trials, suggested a concise, but potentially rational theory that can illustrate the key of the pathogenesis and treatment of ASD from the aspect of damage control.

This study presents a reproducible and scalable method for synthesizing silica nanoparticles (SNPs) with controlled sizes below 200 nm, achieved by systematically varying three key reaction parameters: ammonium hydroxide concentration, water concentration, and temperature. SNPs with high monodispersity and controlled dimensions were produced by optimizing these factors. The results indicated a direct correlation between ammonium hydroxide concentration and particle size, while higher temperatures resulted in smaller particles with increased polydispersity. Water concentration also influenced particle size, with a quadratic relationship observed. This method provides a robust approach for tailoring SNP sizes, with significant implications for biomedical applications, particularly in drug delivery and diagnostics. Using eco-friendly solvents such as ethanol further enhances the sustainability and cost-effectiveness of the process.

Glioblastoma (GBM) is the most common malignant primary brain tumor, with a median survival rate of less than two years. Currently, there is no cure for GBM, underscoring the urgent need for innovative treatment approaches. Vaccine design emerges as a crucial strategy, offering a safe and effective means for both preventive and therapeutic interventions against GBM. In this study, we targeted four GBM-associated mutated surface proteins—urokinase plasminogen activator sur-face receptor (PLAUR), integrin beta-3 (ITGB3), and the B-41 alpha chain (HLA-B) and A-24 alpha chain (HLA-A) of the HLA class I histocompatibility antigens—to design a peptide-based vaccine. The vaccine construct includes cytotoxic T lymphocyte (CTL) and T helper cell (Th cell) epitopes, and was meticulously evaluated for antigenicity, allergenicity, and toxicity. The results indicate that the vaccine is antigenic and non-allergenic, making it a promising candidate. Additionally, the physico-chemical properties of the vaccine suggest stability and suitability for further de-velopment. Immune simulation studies predict efficient immune responses upon vaccine ad-ministration. Our vaccine shows promise as a potential tool in the fight against GBM, offering new hope for patients facing this devastating disease.

The inhibition of kynurenine aminotransferase II (KATII) is a target for treating several diseases with an excess of kynurenic acid (KYNA). KATII inhibitors exist, but they have adverse side effects, given their irreversible inhibition mechanism. This study aimed to discover potent and safe inhibitors of KATII by using computational and in vitro methods. We identified herbacetin and (-)-Epicatechin as reversible KATII inhibitors from a small library of natural compounds, whose Glide docking scores (-8.66 kcal mol-1 and-8.16 kcal mol-1, respectively) and MM/GBSA binding energies (-50.30 kcal mol-1 and -51.35 kcal mol-1, respectively), which are higher scores than the standard inhibitor, PF-04859989 (-7.12 kcal mol-1 and -38.41 kcal mol-1, respectively). The ADMET analysis showed that herbacetin and (-)-Epicatechin have suitable pharmacokinetic parameters, are moderately bioavailable, and have a safe toxicity profile. Their KATII inhibitory activity is in the range of IC50 values of 5.98± 0.18 µM and 8.76 ± 0.76 µM, respectively. Furthermore, the MTT assay for cell toxicity showed that the two compounds do not alter HepG2 cell viability at their required concentration for KATII inhibition. These results show that herbacetin and(-)-Epicatechin are suitable for KATII inhibition and appropriate candidates for further development of KATII inhibitors.

Pain diagnosis remains a challenging task due to its subjective nature, the variability in pain expression among individuals, and the difficult assessment of the underlying biopsychosocial factors. In this complex scenario, artificial intelligence (AI) can offer the potential to enhance diagnostic accuracy, predict treatment outcomes, and personalize pain management strategies. This review aims at dissecting the current literature on computer-aided diagnosis methods. It also discusses how AI-driven diagnostic methods can be integrated into multimodal models that combine various data sources, such as facial expression analysis, neuroimaging, and physiological signals, with advanced AI techniques. Despite the significant advancements in AI technology, its widespread adoption in clinical settings faces crucial challenges. Ethical considerations related to patient privacy, biases, and lack of reliability and generalizability are the main issues. Furthermore, there is a need for high-quality real-word validation as well as the development of standardized protocols and policy rules to guide the implementation of these technologies in diverse clinical settings.

Integrated nutrient management (INM) is an approach that optimizes the benefits derived from various nutrient sources and beneficial soil microorganisms in an integrated manner to increase crop productivity while maintaining soil fertility. An open-field experiment was conducted at Cabuyao, Laguna, Philippines to investigate the effects of combining chemical fertilizers, vermicompost, arbuscular mycorrhizal fungi (AMF), and nitrogen-fixing bacteria (Azospirillum spp.) on the growth, nutrient uptake and yield of tomato. The experiment was arranged in a randomized complete block design replicated four times. The treatments were recommended rate of chemical fertilizer (RRC), combined 50% RRC and 4 t ha-1 vermicompost (INM 1), AMF inoculation with combined nutrient sources (INM 2), and dual inoculation with AMF and Azospirillum in synergy with combined nutrient sources (INM 3). Results revealed that the growth parameters were not significantly affected by the treatments, but the highest data were observed in the treatments under INM. AMF inoculation significantly increased phosphorus, potassium, calcium, and magnesium uptake of tomato while INM 3 recorded the highest nitrogen uptake. Treatments with vermicompost application recorded significantly higher uptake of copper. INM 1, INM 2, and INM 3 gave a significantly higher fruit yield than the RRC with an increase of 7.98%, 13.40%, and 13.65%, respectively. The percentage of mycorrhizal root colonization and number of rhizosphere spores were higher in mycorrhizal plants. Fruit yield and AMF root colonization are positively correlated with uptake of various nutrients. The results imply that these INM strategies can improve growth of tomato, increase fruit yield, reduce the amount of chemical fertilizers applied, and potentially lead to economic, soil health and environmental benefits.

With the significant annual increase in the market demand for biopesticides, the industrial production demand for predatory mites, which hold the largest market share among biopesticides, has also been rising.To achieve efficient and low energy consumption control of predatory mite breeding environmental parameters, accurate estimation of breeding environmental parameters is necessary. This paper collects and pre-processing hourly time-series data of temperature and humidity from industrial breeding environments. Time series prediction models such as SVR, LSTM, GRU, and LSTNet are applied to model and predict historical data of the breeding environment. Experiments validate that the LSTNet model is more suitable for such environmental modeling. To further improve prediction accuracy, the training data for the LSTNet model is enhanced using hierarchical clustering of time-series features. After augmentation, the root mean square error (RMSE) of temperature prediction decreased by 27.3%, and the RMSE of humidity prediction decreased by 32.8%, significantly improving the accuracy of multi-step predictions and providing substantial industrial application value.

Background: Anxiety disorders can be both an independent risk factor of many somatic conditions and the cause of complications of various organic disorders leading to poor prognosis. Objectives: The purpose of this study is to compare the heart rate variability (HRV) recorded both during the day and at night in patients with anxiety disorders and healthy individuals. Methods: The study was conducted on fifty consecutive outpatients with anxiety disorders who participated in intensive group psychotherapy. The diagnosis was made according to DSM-IV-TR criteria using the PSE-10 questionnaire. Out of 50 patients under study, 17 were diagnosed with panic disorder (PD) and 21 with generalized anxiety disorder (GAD). The control group consisted of 40 healthy people. The resulting three groups were compared in terms of circadian HRV using the Oxford Medilog Suprima Holter System. Results: The HRV analysis showed the nocturnal falls in the time and frequency parameters related to parasympathetic activity (rMSSD, pNN50, HF). The most unfavourable alterations were observed in the PD group, which comprised the disappearance of day vs. night amplitude of the majority of HRV parameters. Hence, the PD group was particularly susceptible to the arrhythmic events. It was noticeable that nocturnal vagotonia in the PD group was significantly lower as compared with the GAD and control group. Conclusions: The innovative aspect of the present study was to find a distinct profile of HRV with regard to the types of anxiety disorders because of the existing considerable differences between the nature of PD and GAD.

This study investigates the impact of vertical greenery systems (VGS) applied to heavyweight walls on indoor thermal conditions in a building module situated in the Mediterranean climate of Catania, Italy. Using dynamic simulations in TRNSYS, the research compares the thermal behavior of walls constructed from hollow clay blocks (Poroton) and lava stone blocks with a lightweight wall setup already in place at the University of Catania. The primary focus is on evaluating the VGS’s effect on reducing peak inner surface temperatures and moderating heat flux fluctuations entering the building. The findings indicate that adding a vertical greenery layer to heavyweight walls can decrease the peak inner surface temperature by up to 1.0°C compared to the same wall without vegetation. However, the greenery’s impact on mitigating heat flux fluctuations is less pronounced than in the case of the lightweight wall. This research underscores the potential of green facades in enhancing indoor thermal comfort in regions with climates similar to the Mediterranean, providing valuable insights for sustainable building design and urban planning.

This study aims to propose a method for constructing basic digital twin data in South Korea by adhering to international standards and utilizing publicly available data. Specifically, the study focuses on designing and proposing a digital twin data model for buildings, which are the most applicable among the basic digital twin data. To achieve this, the first section provides essential background information, introduces concepts and requirements related to digital twin basic data, and offers a brief overview of CityGML. The second section explains the methodology and data used in this study. The third section presents the main findings: the selection of public data (buildings) for constructing digital twin basic data, the mapping process using CityGML, and the creation of UML diagrams. The fourth section discusses these findings. Finally, the conclusion and suggestions for future research are provided. This approach enhances the accuracy of building-related digital twin data and supports the use of digital twin services in both public and private sectors by enabling various spatial analyses.

Shape memory alloys (SMA) are becoming a more important factor in actuation technology. Due to their unique features, they bring the potential to safe weight, installation space and reduce energy consumption. The system integration of the generally small diameter NiTi wires is an important cornerstone for the emerging technology. Crimping, a common method for the mechanical and electrical connection of SMA wires, has several drawbacks when it comes to miniaturization and high force outputs. For high force applications for example, multiple SMA wires in parallel are needed to keep actuation frequencies high, while scaling up the actuation force. To meet these challenges, the proposed study deals with the development of a resistance welding process for manufacturing NiTi wire bundles. The wires are welded to sheet metal substrate, resulting in promising functional properties and high joint strengths. The welding process benefits from low cost, easy to control parameters and good automation potential. A method for evaluating the resistance welding process parameters is presented. With these parameters in place, a manufacturing process for bundled wire actuators is discussed and implemented. The welded joints are examined by peel tests, microscopy, and fatigue experiments. The performance of the manufactured bundle actuators is demonstrated by comparison to a single wire with the same accumulated cross-sectional area.

Oxidative stress plays an essential role in the pathological processes that trigger various chronic liver diseases and contributes to the development of hepatocarcinogenesis. Antioxidants from natural sources trap free radicals by converting them into non-harmful products and minimize oxidative stress, playing a crucial function in the treatment of free radical-induced diseases. However, the activity of these antioxidants is limited due their poor bioavailability, which is why various nano-drug delivery systems have been developed to improve their stability, promote smooth release, and targeted delivery for liver cancer treatment. Specifically, this review aims to report recent scientific findings of novel nano-formulations containing natural antioxidant molecules targeted for the treatment of liver cancer.

Genetic similarity determines the extent to which two genotypes share common genetic material. It can be measured in various ways, such as comparing DNA sequences, proteins, or other genetic markers. The significance of genetic similarity is multifaceted and encompasses various fields, including evolutionary biology, medicine, forensic science, animal and plant breeding, and anthropology. Genetic similarity is an important concept with wide application across different scientific disciplines. In the presented study, six measures for calculating genetic similarity were compared: Euclidean, Jaccard, Kulczyński, Sokal and Michener, Nei, and Rogers. The research material included 21 rapeseed genotypes (ten interspecific Brassicaceae hybrids of F2 generation, and 11 of their parental forms) and 146 alleles, obtained using 21 ISSR molecular markers. The results indicate that the research material was divided into two identical groups using any of the proposed methods, despite differences in the values of genetic similarity coefficients. Two of the presented measures of genetic similarity (Sokal and Michener, and Euclidean) were the same.

The breast holds significant importance in women's lactation process. The breast has diverse tissues such as glandular, Cooper’s ligament, lactiferous ducts, adipose, muscles, and skin with various mechanical properties. Most soft tissues exhibit nonlinear, viscoelastic, and anisotropic mechanical behaviour. Stiffness is one of the commonly used mechanical properties for measuring mechanical behaviour in soft tissues. However, this is typically used in simplifying cases where analysis is limited to within the linear elastic region. Young’s modulus is the prevailing measure for quantifying stiffness in tissues. This systematic review examines commonly used techniques for mechanically characterising breast soft tissues to close the gap in the literature. Additionally, this systematic review summarises the mechanical behaviour of the breast tissues available in the literature and highlights the uncovered areas to understand the mechanical behaviour of breast tissues fully. These include a) more mechanical behaviour studies, allowing more accurate modelling for other applications, b) Viscoelastic analysis studies, and c) mechanical analysis on other breast tissues, such as the lactiferous duct, also known as the milk duct. The data obtained in the review can be used as inputs in computational models to analyse the behaviour of the breast tissues.

Electric tractors have many advantages, including high torque, excellent controllability, energy efficiency, simple structure, and electric interface for expansion. However, a significant limitation lies in their endurance. This study presents the design of an extended-range power supply system to ensure continuous endurance of electric tractor. The objective is to provide a continuous power source for our self-developed electric tractor while preserving the benefits of electric propulsion. Extended-range power systems utilize a primary mover, typically an oil-fueled internal combustion engine, to drive the generator for electricity generation, and the generated AC form electricity is subsequently converted into stable DC bus voltage by a power electronic converter. The hardware and control design of the extended-range power supply system have been finalized and validated through experimental trials. Results demonstrate the system’s capability to sustain a stable DC bus voltage amidst disruptions such as sudden load shifts and fluctuations in prime mover speed. Even with 50% sudden load change, the voltage drop is within 12% and could recover to ±3% within 4 seconds. The range extender can be used alone without battery to power the electric tractor, or it can used in parallel with other extended-range extenders or battery thanks with the droop control ability for power sharing.

This study focuses on predicting PM2.5 levels at the University of Petroșani by employing advanced machine learning techniques to analyze a dataset that encapsulates a wide array of air pollutants and meteorological factors. Utilizing data from IoT sensors and established environmental monitoring stations, the research leverages Random Forest, Gradient Boosting Machines, and Support Vector Regression models to forecast air quality, emphasizing the complex interplay between various pollutants. The models demonstrate varying degrees of accuracy, with the Random Forest model achieving the highest predictive power, indicated by an R2 score of 0.82764. Our findings highlight the significant impact of specific pollutants such as NO, NO2, and CO on PM2.5 levels, suggesting targeted mitigation strategies could enhance local air quality. Additionally, the study explores the role of temporal dynamics in pollution trends, employing time-series analysis to further refine the predictive accuracy. This research contributes to the field of environmental science by providing a nuanced understanding of air quality fluctuations in a university setting and offering a replicable model for similar environments seeking to reduce airborne pollutants and protect public health.

The proliferation of fake news on social media platforms poses significant challenges to information authenticity and public trust. In this study, the impact of various word embedding techniques on the performance of both machine learning and deep learning models for fake news detection is systematically evaluated. The comprehensive TruthSeeker dataset, which spans over a decade of labeled news articles and social media posts, is utilized. Three popular word embedding techniques are analyzed: TF-IDF, Word2Vec, and FastText. These embeddings were tested with multiple machine learning classifiers, including logistic regression, naive Bayes, K-nearest neighbors, support vector machines, multilayer perceptrons, decision trees, and random forests, as well as deep learning models, specifically convolutional neural networks (CNNs). Among machine learning models, the Support Vector Machine (SVM) with TF-IDF achieved the highest accuracy of 99.03%, precision of 98.92%, recall of 99.15%, and F1 score of 99.03%. The Multilayer Perceptron (MLP) also demonstrated strong performance with Word2Vec, reaching an accuracy of 95.24%, precision of 94.95%, recall of 95.50%, and F1 score of 95.07%. For deep learning models, CNNs combined with TF-IDF embeddings showed outstanding results, achieving an accuracy of 98.99%, precision of 98.56%, recall of 99.48%, and F1 score of 99.02%. These results highlight the critical role of word embeddings in enhancing model accuracy and reliability in misinformation detection.

The goal is the optimal synthesis of the parameters of the control law for a nonlinear satellite attitude control system under constraints related to the saturation effect of reaction wheels. The maximum stability degree of the control system is considered as a criterion for the optimality of the parameters of the control law, and the absolute values of the control torques and angular velocities of the reaction wheels, achievable within the limits of the physical characteristics of the drives, are considered as constraints. The solution to the optimal synthesis problem is based on the transformation of the nonlinear control system model into a linear model, within the framework of the problem of global asymptotic stability of the control system is also guaranteed. The problem is decomposed into a subproblems of obtaining the optimal transient process shape in the control system and considering the constraints. A method of synthesizing the optimal transient process shape based on the criterion of maximum stability degree had been developed. An analytical method of determining the optimal values of the control law parameters, based on decomposing the normalized characteristic polynomial in the linear model into three identical factors had been proposed. A method with regards to the constraints of the control torque and angular speed of the reaction wheels, based on transitioning from relative to real time is developed. An algorithm for calculation of the transition scale from relative to real time, ensuring the fulfillment of all constraints in the optimal synthesis problem, is proposed. An example demonstrating the efficiency and simplicity of the proposed methods and algorithm for targeted selection of technical characteristics of the control system, considering the maximum absolute values of angular speeds and control torques of the reaction wheels, is provided.

Transition metal dichalcogenides (TMDs) monolayers exhibit unique valleytronics properties due to the dependency of the coupled valley and spin state at the hexagonal corner of the first Brillouin zone. Precisely controlling valley spin-polarization via manipulating the electron population enables its application in valley-based memory or quantum technologies. This study uncovered the uncompensated spins of the antiferromagnetic oxide (NiO) serving as the ferromagnetic (FM) order to induce valley spin-polarization in molybdenum disulfide (MoS₂) monolayers via the magnetic proximity effect (MPE). A spin-resolved photoluminescence spectroscopy (SR-PL) was employed to observe MoS₂, where the spin-polarized trions appear to be responsible for the MPE, leading to a valley magnetism. Results indicate that local FM order from the uncompensated surface of NiO could successfully induce significant valley spin-polarization in MoS₂ with the depolarization temperature approximately at 100 K, which is relatively high compared to related literature. This study reveals new perspectives and potential of AFM materials in the field of exchange-coupled van der Waals heterostructures.

Traditional 3D reconstruction models have consistently encountered a challenge: attaining high recall of object edges while preserving precision. In this paper, we introduce a post-processing method Multi-Head Attention Refiner (MA-R) aimed at tackling this challenge by integrating a multi-head attention mechanism within the U-Net style refiner module. The 3D reconstruction model applying this method demonstrates excellence in parsing intricate image details, resulting in significant enhancement of boundary predictions and increased recall rates. In our experiments, our method significantly enhances the reconstruction performance of Pix2Vox++ when multiple images are utilized as input. Specifically, it achieves an enhanced Intersection Over Union score of approximately 1.1% compared to the original Pix2Vox++ model when 16-view images are employed.

Structural and functional materials are subjected to harsh oxidizing environments that lead to a rapid decline in their surface chemical stability. At high-temperatures, the diffusion of atoms is erratic; thus, the reactive elements (REs) get a chance to migrate to the surface and look for oxygen-reactive sites. Their migration from the lattice sites creates vacancies in the matrix and thus weakens the bond, making the material prone to environmental degrading factors. Subsequently, the inward diffusion of oxygen, sulfur, nitrogen, or carbon may occupy these vacancies, resulting in undesired precipitation at the grain boundary, which is usually brittle. The solubility and dissociation of attacking species and corrosion products play the most critical role in corrosion in high-temperature water. To evade such situations, Ti, Al, and Cr are added in Ni/Fe-based alloys, forming a dense oxide layer on the surface that impedes further surface migration of ions. The stability of the alloys is then determined by the capability of these oxide layers to heal or reform during spalling/cracking. This review attempts to understand the migration of REs at the interfaces to prepare structural materials in any unexpected set of oxidizing service conditions. This review will also try to establish the interaction mechanism of REs novel/conventionally added in the alloys with the oxidizing elements in the environments to design better degradation-resistant high-temperature alloys.

Vitiligo is a chronic autoimmune disease characterized by progressive depigmentation of the skin caused by the selective destruction of melanocytes. Although its etiopathogenesis remains unclear, multiple factors are believed to be involved, including genetic and metabolic factors linked to cellular oxidative stress, melanocyte adhesion defects, innate and adaptive immunity. The aim of this review is to provide an overview of the current state of knowledge regarding the role of different cellular mechanisms, including cytokines and chemokines interactions in the pathogenesis of vitiligo. Although there is no definitive cure for vitiligo, excessive progress has been made and several treatments have shown favourable results. A thorough understanding of the basis of the disease, uncover promising drug targets for future research, providing clinical researchers with valuable insights for developing improved treatment options.

Neurofibromas, rare benign tumors of the peripheral nerve sheath, present diagnostic challenges, particularly in diabetic patients with toe ulcers. This case involves a 55-year-old female with type 2 diabetes mellitus who developed an enlarging ulcer on her right second toe. The initial evaluation suggested a diabetic ulcer; however, advanced imaging revealed a mass-like lesion. Partial excision and biopsy confirmed a neurofibroma with spindle cells within the myxoid stroma and S100 protein expression. One month later, total excision and Z-plasty reconstruction were performed under general anesthesia. The patient’s postoperative recovery was uneventful, and the patient was discharged without complications. Follow-up revealed successful healing with no recurrence or functional issues. This case highlights the importance of considering neurofibromas in the differential diagnosis of diabetic toe ulcers to avoid misdiagnosis and ensure appropriate management.

Infantile Neuroaxonal Dystrophy (INAD) is a rare neurodegenerative disorder, affecting 1:1,000,000 population. It results from pathogenic variants in the PLA2G6 gene located on chromosome (22q13.1). The onset of symptoms usually occurs between 6 to 18 months, causing developmental regression leading to debilitating symptoms such as muscle weakness, dementia, and loss of basic skills. Eventually, it progresses to life-threatening symptoms including breathing difficulties, which limits the life expectancy to 5-10 years. While potential genetic therapy for treatment is are being developed, they are yet to be approved for use, and management remains essentially supportive. This case report is of a 9-year-old Pakistani girl with INAD. She presented with recurrent chest infections, developmental regression, loss of speech, paralysis, hypertension, and eventually breathing difficulties. Brain magnetic resonance imaging and genetic testing con-firmed the diagnosis. This case posed diagnostic challenges in view of its overlapping clinical presentation. Through this report, we aim to raise awareness about the condition among practitioners, outline the importance of genetic counseling in susceptible couples and suggest potential areas of further research.

This paper investigates five different GARCH models (GARCH, EGARCH, IGARCH, Component GARCH (CGARCH) and GJR-GARCH) along with six distributions (Normal, Student’s t, GED and their skewed forms), which are used to forecast the volatility for the Bulgarian Stock index SOFIX. We use a GARCH model to predict how much time it will take, after the latest crisis, for the SOFIX index to reach its historical peak once again. The empirical data covers the period between the years 2000 and 2024, including the 2008 financial crisis and the COVID-19 pandemic. The purpose is to answer which of the five models is the best at forecasting the volatility of SOFIX and which distribution is most appropriate. The results, based on BIC and AIC information criteria, show that the ARMA(1,1)-CGARCH(1,1) specification with the Student t-distribution is preferred for forecasting. With the help of 5000 simulations, it is estimated that the chances of Index SOFIX reaching its historical peak value of 1976.73 (08.10.2007) are higher than 90% at 13.08.2087.

The development of one technology can be portrayed by common methods like Gartner’s hype cycle or S-curve, however, there is no method to characterize the feature distributions of multiple technologies within a specific domain. This study proposes a big data-based method in terms of four proposed features, namely versatility, significance, commerciality, and disruptiveness, to characterize the technologies within a given domain. The features of technologies are quantitively portrayed using the representative keywords and volumes of returned search results from Google and Google Scholar in two-dimensional analytical spaces of technique and application. We demonstrate the applicability of this method using 452 technologies in the domain of intelligent robotics. The results of our assessment indicate that the versatility values are normally distributed, while the values of significance, commerciality, and disruptiveness follow power-law distributions, in which few technologies possess higher feature values. We also show that significant technologies are more likely to be commercialized or causing potential disruption, as such technologies have higher scores in these features. Further, we validly prove the robustness of our approach via comparing historical trends with literature and characterizing technologies in reduced analytical spaces. Our method can be widely applied in analyzing feature distributions of technologies in different domains, and it can potentially be exploited in decisions like investment, trade, and science policy.

Smartwatches are one of the most relevant fitness trends of the past two decades, and they collect increasing amounts of health and movement data. The accuracy of these data may be questionable and requires further investigation. Therefore, the aim of the present study is to validate smartwatches for use in triathlon training. Ten different smartwatches were tested for accuracy in measuring heart rate, distance (via global navigation satellite systems, GNSS), swim stroke rates and the number of swim laps in a 50 m Olympic-size pool. The optical heart rate measurement function of each smartwatch was compared to that of a chest strap. Thirty participants (15 females, 15 males) ran five 3-minute intervals on a motorised treadmill to evaluate the accuracy of the heart rate measurements. Moreover, for each smartwatch, running und cycling distance tracking was tested over six runs of 4,000 m on a 400 m tartan stadium track, six hilly outdoor runs over 3.4 km, and four repetitions of a 36.8 km road bike course, respectively. Three swimming protocols ranging from 200 m to 400 m were performed in triplicate in a 50 m Olympic-size pool, evaluating tracked distance and detected number of strokes. The mean absolute percentage errors (MAPEs) for the average heart rate measurements varied between 3.1% and 8.3%, with the coefficient of determination ranging from 0.22 to 0.79. MAPE results ranged from 0.8% to 12.1% for the 4,000 m run on the 400 m track, from 0.2% to 7.5% for the 3.4 km outdoor run, and from 0.0% to 4.2% for the 36.8 km bike ride. For the swimming tests, in contrast, the deviations from the true distance varied greatly, starting at a 0.0% MAPE for the 400 m freestyle and reaching 91.7% for the 200 m medley with style changes every 25 m. In summary, for some of the smartwatches, the measurement results deviated substantially from the true values. Measurements taken while road cycling over longer distances with only a few curves were in relative terms more accurate than for outdoor runs and even more accurate than for the 400 m track. In the swimming exercises, the accuracy of the measured distances was severely deteriorated by the medley changes among the majority of the smartwatches. Altogether, the results of this study should help in assessing the accuracy and thus suitability of smartwatches for general triathlon training.

Australia’s avian species are unique and diverse. Due to the dramatic changed in distribution, physiology, and behaviour caused by both changing climatic conditions and human activities, Australian bird species becomes highly vulnerable to health-related factors such as impact injury and vehicle trauma, as well as environmental-related stressors such as animal attack and abnormal behaviours. This is reflected in increasing number of avian patients received by wildlife hospitals. The most common outcome of avian species in wildlife hospitals was euthanasia, only few of them were released back into their ecosystem. During the process of bird rescue and rehabilitation, stress can be caused by various stressors such as injury, infection, trauma, shock and stressful environment in wildlife hospitals and rehabilitation centres. Therefore, in order to better understand the causes of the high rates of mortality and improve the management and conservation strategies, it is important to study the species responses to environmental changes. Similar with other species, in birds, the HPA axis plays an essential role in maintaining homeostasis by producing glucocorticoids (corticosterone in birds). In this study, we sampled a total of 30 individuals humanely euthanised at the Adelaide Koala and Wildlife Centre (AKWC), and noted their clinical information. Feather samples were collected from all 30 individuals, and then were processed and analysed for corticosterone levels using enzyme-immunoassay (EIA). The biological relevance of feather CORT assay was evaluated by comparing the absolute levels of CORT between birds. We also analysed the effects of different stressors by grouped the diagnosis into acute and chronic categories. Although results suggest that stress levels were variable between the diagnosis, no statistically significant difference was found between these two categories in this study due to the limited sample size. We also obtained patient records from the 2022-2023 period from AKWC for retrospective analysis. Records were categorized and analysed based on the diagnoses, species and admission dates. Retrospective analysis suggests that in 2022, the Rainbow Lorikeet had the highest admission rate (192/544, 35.29%), followed by Magpie (124/544, 22.79%). Most admissions occurred in Summer. Musculoskeletal injury was the most prevalent diagnosis across all species with Magpies having the highest rates (73.39%) across all diagnoses and Rainbow Lorikeets the second highest (36.46%). Beak and Feather disease (BFD) was another common diagnosis for lorikeets. Data collected at 2023 followed the similar trend. This is the first study that uses non-invasive method to determine stress levels of rescued Australian native avian species, aims at improving and implementing native avian species management and conservation initiatives. This research also provides a basis for future studies which allow for more detailed analyses of wild populations and a broader range of species.

Temperature Cycle Induced Deracemization (TCID) offers a promising approach to obtain enantiopure solids from racemic mixtures. By combining rapid racemization in solution and temperature swings, homochirality is theoretically achieved. Despite theoretical expectations of doubled yields compared to traditional chiral separation methods, such as in Preferential Crystallization, experimental validation remains lacking. We applied TCID to (1-(4-chlorophenyl)-4,4-dimethyl-2-(1H-1,2,4-triazol-1-yl) pentan-3-one) (Cl-TAK), introducing a post-TCID cooling step to enhance yield and a washing step to augment enantiopurity. This refinement yielded an 89.8% mass yield with 99.1% enantiomeric excess in the crystal phase (c.e.e.) within 24 hours on an 8.75g scale, showcasing improved performance with insignificant process duration extension. Additionally, we explored the stochasticity of deracemization, observing the development from low initial crystal enantiomeric excesses(1-6% c.e.e0) at a 2.5 g scale. Kinetic analysis revealed that a 2% c.e.e0 effectively mitigates chiral flipping risks and induction time in our system. Our study underscores the potential for reduced initial c.e.e. to expedite deracemization and presents a straightforward method to optimize yield and purity, facilitating industrial application.

Cancer is one of the leading causes of death, making timely diagnosis and prognosis very important. Utilization of AI (artificial intelligence) enables providers to organize and process patient data in a way that can lead to better overall outcomes. This review paper aims to look at the varying uses of AI for diagnosis and prognosis and clinical utility. PubMed and EBSCO databases were utilized for finding publications from January 1, 2013, to December 22, 2023. Articles were collected using key search terms such as “artificial intelligence” and “machine learning.” Included in the collection were studies of the application of AI in determining cancer diagnosis and prognosis using multi-omics data, radiomics, pathomics, clinical and laboratory data. The resulting 89 studies were categorized into eight sections based on the type of data utilized and then further subdivided into two subsections focusing on cancer diagnosis and prognosis, respectively. 8 studies integrated more than one form of omics, namely genomics, transcriptomics, epigenomics, and proteomics. Incorporating AI into cancer diagnosis and prognosis alongside omics and clinical data represents a significant advancement. Given the considerable potential of AI in this domain, ongoing prospective studies are essential to enhance algorithm interpretability and to ensure safe clinical integration.

Aim: This study aimed to evaluate the effectiveness of a plyometric training program designed to enhance agility, speed, and social interaction among boys with mild intellectual disability (ID) aged 10-12, within the Special Olympics framework. Participants: Thirty-two boys (mean age = 10.69 ± 0.8 years; mean IQ = 61 ± 7) from three inclusive education centers participated in the study. Methods: The intervention consisted of a 10-week plyometric training program, conducted twice a week. Pre- and post-intervention assessments included the Reaction Time Test, 4-Corner Agility Test, 10-Meter Speed Run, 4x5 Meter Relay Test, and the Friendship Activity Scale (FAS). Results: The study found significant improvements across all measures. Reaction time decreased by 0.83 seconds (t = 7.44, p < 0.001), 4-corner agility improved by 0.77 seconds (t = 11.93, p < 0.001), 4x5 meter speed improved by 0.61 m/s (t = 17.37, p < 0.001), and 10-meter run speed improved by 1.55 m/s (t = -12.76, p < 0.001). Additionally, the FAS score increased by 0.81 points (t = 9.59, p < 0.001), indicating enhanced social interactions. Conclusion: The plyometric training program significantly improved agility, speed, and social interaction in children with mild ID, demonstrating the effectiveness of inclusive, adaptive physical education strategies within the Special Olympics framework.

The aim of this study was to investigate the relationship between postprandial glycemic levels based on flash-monitoring and the production of intestinal hydrogen (H2) and methane (CH4) gases based on measurement of the amount of these gases in exhaled air. We studied 14 subjects with type 2 diabetes mellitus (T2DM) and 10 individuals without diabetes (control) with 3 food-load tests with simultaneous determination of gases in exhaled air and assessment of glucose levels. In 15.4% of patients with T2DM, there was a non-significant increase in exhaled H2. How-ever, all subjects in the control group had significant increase in exhaled H2. Moreover, the level of H2 in exhaled breathafter food load in patients with T2DM was lower than in normoglycemic subjects. Also, in normoglycemic subjects there was an inverse correlation between maximum glucose rise and maximum H2 in exhaled air after food load. At the same time in patients with T2DM the level of CH4 in exhaled air directly correlated with the parameters of postprandial glycemia in the test with lactulose. Confirmation of a causal relationship between decreased H2 production, increased intestinal CH4 production, and more severe postprandial glycemia may identify new therapeutic targets in the correction of postprandial glycemia in patients with T2DM.

Pedestrian trajectories are crucial for self-driving cars to plan their paths effectively. The sensors implanted in these self-driving vehicles, despite being state-of-the-art ones, often face inaccuracies in the perception of surrounding environments due to technical challenges for adverse weather conditions, interference from other vehicles sensors and electronic devices, and signal reception failure, leading to incompleteness in trajectory data. But for real-time decision making for autonomous driving, the trajectory imputation is no less crucial. Previous attempts to address this issue such as statistical inference and machine learning approaches have shown promise. Yet, the landscape of deep learning is rapidly evolving with new and more robust models emerging. In this research, we have proposed an encoder-decoder architecture, Human Trajectory Imputation Model, coined as HTIM, to tackle these challenges. This architecture aims to fill in the missing parts of pedestrian trajectories. The model has been evaluated using the Intersection drone inD dataset, containing trajectory data at suitable altitudes preserving naturalistic pedestrian behavior with varied dataset sizes. To assess the effectiveness of our model, we have utilized L1, MSE, Quantile and ADE loss. Our experiments have demonstrated that HTIM outperforms the majority of the state-of-the-art methods in this field, thus indicating its superior performance in imputing pedestrian trajectories.

A comprehensive modeling framework for the thermoforming of polymer matrix woven laminate composite was developed. Two numerical indicators, the slip path length and traction magnitude, have been identified to be positively correlated to matrix smearing and wrinkling defects. The material model has been calibrated with picture-frame experimental results, and the prediction accuracy for intra-ply shear and thickness distribution were examined with measurements on the physically formed parts. Finally, a parametric study was conducted to determine the relationship between various process parameters and the quality of the formed part. For the trapezoidal part, orienting the laminate at 45-degrees to the mold axis reduces the likelihood of matrix smear and wrinkling defects. Although this laminate orientation yielded a greater spatial variation of part thickness, the thickness deviation is lower than that for the 0-degree orientation case. Higher forming rates were found to result in more defects due to increased slip path lengths and traction magnitudes. Optimal forming speeds should balance rapid shaping within the operating temperature window while avoiding tear. It was discovered that shallower molds benefit from faster ramp rates, while deeper molds require slower rates to manage extensive shearing, stretching, and bending. Faster forming rates lead to smaller thickness increases at high intra-ply shear regions, indicating a shift from intra-ply shear to out-of-plane bending due to the visco-plastic effect of the molten laminate, and can negatively impact part quality. Lastly, it was shown that a well-conceived strategy using darts could improve the part quality by reducing the magnitude of the defect indicators.

Both bacteria product flagellin and macrophages are implicated in HIV infection/disease progression. However, the impact of their interaction on HIV infection and the associated mechanisms remain to be determined. We thus examined the effect of the flagellins on HIV infection of primary human macrophages. We observed that the pretreatment of macrophages with the flagellins from the different bacteria significantly inhibited HIV infection. The mechanistic investigation showed that the flagellin treatment of macrophages downregulated the major HIV entry receptors (CD4 and CCR5) and upregulated the CC chemokines (MIP-1α, MIP-1β, and RANTES), the ligands of CCR5. These effects of the flagellin could be compromised by a toll like receptor 5 (TLR5) antagonist. Given the important role of flagellin as a vaccine adjuvant in TLR5 activation-mediated immune regulation and in HIV infection of macrophages, future investigations are necessary to determine the in vivo impact of flagellin-TLR5 interaction on macrophage-mediated innate immunity against HIV infection and the effectiveness of flagellin adjuvant-based vaccines studies.

Feature selection is predominantly used in machine learning tasks, such as classification and regression. It selects a subset of features (relevant attributes of data points) from a larger set that contributes as optimally as possible to the informativeness of the model. There are exponentially many subsets of a given set, and thus, the exhaustive search is only practical for problems with at most a few dozen features. In the past, there have been attempts to reduce the search space using dynamic programming. However, models that consider similarity in pairs of features besides the quality of individual features do not provide the required optimal substructure. As a result, algorithms, which we will call suboptimal dynamic programming algorithms, find a solution that may deviate significantly from the optimal one. In this paper, we propose a dynamic programming algorithm with an iterative upgrade where the order of feature processing is inverted in each iteration. Such an alternating approach allows for improving the optimization function by using the score from the previous iteration to estimate the contribution of unprocessed features. The iterative process is proven to converge and terminate when the solution does not change in three successive iterations or when the number of iterations reaches the threshold. Results in more than 90 % of tests align with those of the exhaustive search, being competitive and often superior to the reference greedy approach. The validation was done by comparing the scores of output feature subsets and examining the accuracy of different classifiers learned on these features. In the context of feature selection, the proposed algorithm can be characterized as a filter method. However, we expect that the idea of alternating suboptimal optimization will soon be generalized to tasks beyond feature selection.

This work presents a Fault-Tolerant Model Predictive Control (FTMPC) algorithm applied to a simulation model for sewer networks. The control system will aim to prevent contaminated water from escaping the network, especially during periods of heavy rainfall, that can cause combined sewer overflows (CSO), while maintaining the flow of water towards the wastewater treatment plant (WWTP) as close as possible to its nominal value. The main purpose of the work is to preserve the operation of the predictive controller as much as possible, in accordance with its operational objectives, when there may be anomalies affecting the elements of the control system, mainly sensors and actuators. Comparing the results obtained considering various types of faults, with situations of normal controlled operation and with the behavior of the sewer network when no control is applied, will allow some conclusions to be drawn at the end.

Age-related diseases place an intense and growing stress on healthcare systems. Numerous theories of ageing exist. Yet prediction, prevention and treatment limitations of age-related disease persist because we lack a complete aetiological understanding of their origins. Here we propose a new theory that aims to provide a blueprint-type understanding of ageing and disease aetiology, working across multiple scientific disciplines. Supported by specific examples, we demonstrate that the primary driver of much of age-related diseases is the futile triggering of specific molecular pathways in a pathological manner, which we term patho-pathways. Patho-pathways induce pathological cell, tissue and system changes in the form of hyperactivity (undesirable increased and new biological activities that are typical of age related disease). As part of patho-pathways, all wild-type (normal) genes have the potential to contribute to age-related diseases (though specific risk varies and can be formularised). In a domino-style effect, one patho-pathway typically triggers others, resulting in complex, but traceable, cascades. Utility, in terms of changing clinical and scientific practice, is derived from mapping these cascades to create Blueprint Maps that allow identification of biomarkers and therapeutic targets far upstream in the causal chain of events. Finally, our theory provides testable hypotheses concerning predictions of links between otherwise seemingly disparate diseases as well as new interventions into ageing.

Stress is a natural yet potentially harmful aspect of human life, necessitating effective management, particularly during overwhelming experiences. This paper presents a scoping review of personalized stress detection models using wearable technology. Employing the PRISMA-ScR framework for rigorous methodological structuring, we systematically analyzed literature from key databases including Scopus, IEEE Xplore, and PubMed. Our focus was on biosignals, AI methodologies, datasets, wearable devices, and real-world implementation challenges. The review presents an overview of stress and its biological mechanisms, details the methodology for the literature search, and synthesizes the findings. It shows that biosignals, especially EDA and PPG, are frequently utilized for stress detection and demonstrate potential reliability in multimodal settings. Evidence for a trend towards deep learning models was found, although the limited comparison with traditional methods calls for further research. Concerns arise regarding the representativeness of datasets and practical challenges in deploying wearable technologies, which include issues related to data quality and privacy. Future research should aim to develop comprehensive datasets and explore AI techniques that are not only accurate but also computationally efficient and user-centric, thereby closing the gap between theoretical models and practical applications to improve the effectiveness of stress detection systems in real scenarios.

The intelligent morphing wing structure has the characteristics of flexibility, large deformation and adaptive change, which are different from those of the conventional wing. The motion law of the variable-camber leading edge is analysed by the numerical simulation method based on kinematics theory to solve the problem of verifying the motion function and structural strength of the variable camber wing. The driving deformation and aerodynamic load simulation of the variable camber leading edge are realised by designing a follow-up load test apparatus. Based on the numerical simulation of the mechanical boundary, the motion trajectory of the upper and lower wing loading points was predicted, and a multi-point cooperative control system was developed. Multi-sensor iteration was used to ensure the loading accuracy of the test control. The test results show that the average error of the deflection angle is 4.59% in the variable camber leading edge motion test. In the variable camber leading edge strength test, the average error of applied load magnitude and direction is 0.54% and 0.24%, respectively.

The human gastrointestinal gut contains about 100 trillion of microorganisms including up to 5000 different types of bacteria called the "gut microbiome". Alterations in the composition of gut microorganisms (dysbiosis) can cause threatening for life diseases. This present seeks to evaluate if finally diet and more specifically functional foods affect the intestinal microbiome, and if obesity and the metabolic syndrome (Mets) are associated with the intestinal microbiome. This systematic review was accomplished according to PRISMA guidelines mostly using the key words functional foods, microbiome, obesity, Mets, Mediterranean diet. The search was carried out of recent scien-tific articles from the databases Pubmed, Scopus, and Google Scholar. The most studies discussed in this review showed a potential therapeutic effect of the Mediterranean diet rich in beneficial nutrients, on body weight, fat deposition, in correlation with modulation of the synthesis of gut microbiome. This literature review demonstrates a possible relationship between the metabolites of the microflora, the endotoxemia, obesity and Mets. The role of probiotics, prebiotics, and polyphe-nols in the prevention of obesity and Mets is of high importance in promoting healthy aging. The future challenge is to understand how different dietary patterns can regulate the composition of the gut microflora and whether these changes could be long-term.

To investigate the effects of organic fertilizer combined with reduced chemical fertilizer on radish yield, quality, and soil environment in high mountainous areas (elevation: 1800 m), and to mitigate the environmental pollution caused by excessive use of chemical fertilizers. The field trial was conducted to study the effects of different fertilizer treatments. (Control:local fertilizer application rate: 375 kg·hm² reduction in chemical fertilizer + 4500 kg·hm² organic fertilizer; T1:12% reduction in chemical fertilizer + 4500 kg·hm² organic fertilizer; T2:20% reduction in chemical fertilizer + 4500 kg·hm² of organic fertilizer; T3:28% reduction in chemical fertilizer + 4500 kg·hm² organic fertilizer). Four different fertilizer ratios were studied to assess their impacts on radish quality, yield, and soil environment. The findings showed that T2 significantly increased radish yield by 12.92%. Moreover, it led to significant improvements in the content of vitamin C, soluble sugars, soluble solids, soluble proteins, titratable acidity, and glucosinolates, which increased by 10.62%, 2.15%, 50.00%, 26.90%, 43.90%, and 44.57%, respectively. Treatment T2 also significantly increased soil nutrient content, with a 7.69% and 14.29% increase in total nitrogen and total phosphorus content compared to the control (Control) treatment, and a significant reduction of 21.64% in soil bulk density . T2 treatment significantly enhanced soil urease activity, sucrase activity, alkaline phosphatase activity, and catalase activity, showing an improvement of 28.97%, 55.92%, 52.08%, and 17.47% compared to the control, respectively (p&lt;0.05). Moreover, treatment T2 resulted in a relative abundance increase of 12.25% and 10.43% in Proteobacteria and Actinobacteria respectively. Thus, the combined application of T2:20% reduction in chemical fertilizer + 4500 kg·hm² of organic fertilizer improved the quality and yield of radish while optimizing the soil environment. T2 effectively promoted radish growth, enhanced radish yield and quality, and improved the soil environment.

Retiring coal power plants can reduce air pollution and health damages. However, the spatial distribution of those impacts remains unclear due to complex power system adjustments and pollution chemistry and transport. Focusing on coal retirements in Pennsylvania (PA), we analyze six counterfactual scenarios for 2019 that differ in retirement targets (e.g., reducing 50% of coal-based installed capacity vs. generation) and priorities (e.g., closing plants with higher cost, closer to Environmental Justice Areas, or with higher CO₂ emissions). Using a power system model of the PJM Interconnection, we find that coal retirements in PA shift power generation across PA and the Rest of PJM region leading to scenario-varying changes in the plant-level release of several air pollutants. Due to air pollution chemistry and transport and socio-demographics, these changes in turn give rise to a reduction of 10 to 182 PM_2.5-attributable deaths in PJM across the six scenarios, with most reductions occurring in PA. Scenarios that reduce more coal power generation yield greater aggregate health benefits due to air quality improvements in PA and adjacent downwind regions. In addition, vulnerable populations—in both PA and Rest of PJM—benefit most in scenarios that prioritize plant closures in PA near Environmental Justice Areas. These results demonstrate the importance of considering cross-regional linkages and socio-demographics in designing equitable retirement strategies.

Timely and accurate information on tree species is crucial for the sustainable management of natural resources, forest inventory, biodiversity detection, and carbon stock calculation. The advancement of remote sensing technology and artificial intelligence has facilitated the acquisition and analysis of remote sensing data, resulting in more precise and effective classification of tree species. Multimodal remote sensing data and deep learning seem to be the current tree species classification research mainstream, whether or not. The current review on the remote sensing data and deep learning tree species classification methods perspectives to analyze the unimodal and multimodal remote sensing data and classification methods in this realm is missing. To bridge the gap, we search for major trends in the remote sensing data and tree species classification methods, provide a detailed overview of classic deep learning-based methods for tree species classification, and discuss the limitations.

Reservoirs created by damming rivers significantly modify the environment and problems may arise: the storage of nutrients and organic matter in reservoirs often leads to decreased water quality due to eutrophication. Reservoirs built on lowland rivers are exposed to significant nutrient loads, often leading to eutrophication. In this article, the Sulejów Reservoir, in Central Poland, was the subject of the research, which focused on the use of Sentinel-2 remote sensing data to detect phytoplankton blooms, and on understanding the pattern of wind-driven surface currents using the CCHE2D model (a depth-averaged hydrodynamic model). The calculation of the total phosphorus load has shown that the reservoir mainly acts as nutrient storage. Still, during the low flow and intensive phytoplankton bloom, it can be a source of nutrients. The distribution of phytoplankton bloom on the Sulejów Reservoir was documented using eight Sentinel-2 satellite images from the vegetation season of 2020 and the Normalized Difference Chlorophyll Index (NDCl). Coupling remote sensing data and numerical modelling helps to interpret the hydrodynamic model results and understand nutrients and sediment dynamics within the reservoir. Hydrodynamic modelling combined with remote sensing data can be a valuable tool for selecting appropriate locations for water quality measurements at monitoring stations.

Modular steel buildings (MSBs) interlocking inter-module connections (IMCs) have piqued researchers’ interest. However, the existing literature has not yet studied the optimisation of its plate thicknesses. This paper, therefore, focuses on optimising interlocking (IMCs) plate thickness in (MSBs), leveraging previous experimental and numerical simulation methodologies. Various numerical models for four MSBs interlocking (IMCs) with plate thicknesses (4 mm, 6 mm, 10 mm, and 12 mm) were developed under compression loading conditions. The study’s novelty lay in its comprehensive parametric analysis, which evaluated the slip phenomenon in (MSBs) connections and introduced a slip prediction model validated against empirical data. Further innovative machine learning approach was utilised to predict slip values based on applied force through a random forest regression model trained using the 'Treebagger' function. Sensitivity analysis and comparisons with alternative methods were utilised to underscore the reliability and applicability of the findings. The results showed that 11.03 mm was the optimal plate thickness for interlocking (IMCs) in modular steel buildings, with up to 8.08% reduced material costs. Increasing plate thickness boosts its deformation resistance by up to 50.75%. ‘TreeBagger’ random forest for anomaly detection and machine learning improves slip prediction up to 7% at higher force levels.

Off-grid electrification planning increasingly recognizes the importance of productive use of electricity (PUE) to promote community value creation and (financial) project sustainability. To ensure a sustainable and efficient integration in the community and energy system, PUE assets must carefully be evaluated to match both the community needs and the residential electricity demand patterns. We propose a novel methodology interlinking qualitative interviews, statistical analysis, and energy system modelling to optimize decision-making for PUE integration in off-grid energy systems in rural Madagascar by aligning relevant PUE effectively with anticipated residential electricity demand patterns based on socio-economic determinants of the community. We find that a possible contribution of the PUE to reducing the electricity costs depends signifi-cantly on three factors: 1. the residential electricity consumption patterns that are influenced by the socio-economic composition of the community, 2. the degree of flexibility of i) PUE assets and ii) operational preferences of the PUE user, and 3. the capacity of community members to finance and operate PUE assets. Our study demonstrates that significant cost reductions for PUE-integrated off-grid energy systems can be achieved by applying our proposed methodology. When matching PUE and residential consumption patterns, the integration of PUE assets in residential community energy system can reduce the financial risk of operators, provided the PUE enterprise operates reliably and sustainably. We highlight that the consideration of local value chains and co-creation approaches are essential to ensure the energy system is addressing the community’s needs, creates value for the community, enhances the project´s financial sustainability, and is achieving the overall objectives of decentralized energy system planning.

The incremental sheet forming represents a relatively recent technology that guarantees high customization, thanks to the layered manufacturing principle typical of rapid prototyping, and cost-effectiveness, because it does not require dedicated equipment. Research has initially shown that this process is effective in metal materials capable of withstanding plastic deformation but, in recent years, the interest in this technique has been increasing for the manufacture of complex polymer sheet components as an alternative to the conventional technologies, based on heating-shaping-cooling manufacturing routes. Conversely, incremental formed polymer sheets can suffer from some peculiar defects, for example twisting. To reduce the risk of this phenomenon and the occurrence of failures, a viable way is to choose toolpath strategies that make the tool/sheet contact conditions less severe, and this represents the main goal of the present research. Polycarbonate sheets were worked by incremental forming; in detail, cone frusta with a fixed wall angle were manufactured with a reference and a stair toolpath strategy, and both the forming forces and the twist angle were monitored. The analysis of the results highlighted that a stair toolpath involving an alternation of diagonal up and vertical down steps represents a useful strategy to mitigate the forming forces and, with them, the occurrence of the twisting phenomenon in incremental formed thermoplastic sheets.

Polymer inclusion membranes (PIMs), which contained cellulose tri-acetate used as a polymer base, a plasticizer in the form of o-NPOE, and meso-tetra methyl tetrakis-[methyl-2-(4-acetlphenoxy)] calix[4]pyrrole (KP) used as a carrier, were prepared and tested for the effective purification of aqueous solutions of methylene blue dye. The scanning electron microscope (SEM), thermogravimetric analysis (TGA), and attenuated total reflection Fourier transform infrared (ATR-FTIR) were used to define the microstructure and surface of PIMs. Experimental results showed that with the increased concentration of methylene blue in an aqueous solution, the removal percentage also increased. Further observation also showed that the flux increased with the rise of the source phase pH values from 3 to 10. The carrier and plasticizer content in the membrane significantly influenced the membrane’s transport properties. The optimal composition of the membrane in per cent by weight was for KP: 74% plasticizer; 18% support; 8% carrier. It was shown that the membrane with optimal composition showed good reusability and enabled the easy and spontaneous separation of methylene blue from aqueous solutions.