A recently developed differential geometric representation of redundant serial robot kinematics is employed to create an extended operational space dynamics and control formulation that explicitly accounts for redundant robot degrees of freedom. This formulation corrects deficiencies in kinematics and dynamics of redundant serial robots that have relied for over half a century on error prone generalized inverse velocity-based kinematics for redundancy resolution. New ordinary differential equations of robot operational space dynamics are obtained, without the need for ad-hoc derivation, in terms of task coordinates and self-motion coordinates that represent robot redundancy. A new extended operational space control approach is presented that exploits ordinary differential equations of motion in term of task and self-motion coordinates. This enables enforcement of desired output trajectories, in tandem with direct enforcement of self-motion dependent operational space trajectories that are subject to obstacle avoidance and performance constraints. Four examples are presented with a one degree of redundancy robot that demonstrate validity and superior performance of the new formulation, relative to traditional task space methods used for redundant serial robot control. Finally, an example with eight degrees of redundancy is presented that further illustrates superior performance of the new formulation.

Human-Robot Interaction (HRI) for collaborative robots has become an active research topic recently. Collaborative robots assist the human workers in their tasks and improve their efficiency. But the worker should also feel safe and comfortable while interacting with the robot. In this paper, we propose a human-following motion planning and control scheme for a collaborative robot which supplies the necessary parts and tools to a worker in an assembly process in a factory. In our proposed scheme, a 3-D sensing system is employed to measure the skeletal data of the worker. At each sampling time of the sensing system, an optimal delivery position is estimated using the real-time worker data. At the same time, the future positions of the worker are predicted as probabilistic distributions. A Model Predictive Control (MPC) based trajectory planner is used to calculate a robot trajectory that supplies the required parts and tools to the worker and follows the predicted future positions of the worker. We have installed our proposed scheme in a collaborative robot system with a 2-DOF planar manipulator. Experimental results show that the proposed scheme enables the robot to provide anytime assistance to a worker who is moving around in the workspace while ensuring the safety and comfort of the worker.

The vibrations of a Cartesian cutting machine caused by the pneumatic tool are studied with a sub-system approach. The cutting head is modeled as an equivalent robot arm which is able to mimic the measured resonances, The Cartesian structure is modeled according to the mode superposition approach. The full model is able to predict the variations in the response of the machine to tool excitation that are caused by the motion of the head along the rails of the Cartesian structure. Comparisons with experimental results are made. Finally, the mathematical model is used for assessing the effectiveness of a vibration absorber tuned to main resonance frequency of the cutting head.

In this paper is presented the design and syntheis of a dynamic output feedback neural network controller for a non-holonomic mobile robot. First the dynamic model of a non-holonomic mobile robot is presented, in which these constraints are considered for the mathematical derivation of a feasable representation for this kind of robot. Then two control strategies are provided based on kinematic control for this kind of robot. The first control strategy is based on driftless control, this means, that considering that the velocity vector of the mobile robot is orthogonal to its restriction a dynamic output feedback and neural network controller is designed in order that the control action would be zero only when the velocity of the mobile robot is zero. The Lyapunov stability theorem is implemented in order to find a suitable control law. Then another control strategy is designed for trajectory tracking purposes, which similar to the driftless controller, a kinematic control scheme is provided but suitable to implement in more sophisticated hardware. In both control strategy a dynamic control law is provided along with a feedforward neural network controller, so in this way, by the Lyapunov theory the stability and convergence to the origin of the mobile robot position coordinates is ensured. Finally, two numerical experiment are presented in order to validate the theoretical results synthetized in this research study. Discussions and conclusions are provided in order to analyze the results found in this research study.

This paper presents a framework for the motion planning and control of redundant manipulators with the added task of collision avoidance. The algorithms that were previously studied and tested by the authors for planar cases are here extended to full mobility redundant manipulators operating in a three-dimensional workspace. The control strategy consists of a combination of off-line path planning algorithms with on-line motion control. The path planning algorithm is used to generate trajectories able to avoid fixed obstacles, detected before the robot starts to move; it is based on the potential fields method combined with a smoothing interpolation that exploits Bézier curves. The on-line motion control is designed to compensate for the motion of the obstacles and to avoid collisions along the kinematic chain of the manipulator; it is realized by means of a velocity control law based on the null space method for redundancy control. A term of the control law takes into account the speed of the obstacles as well as their position. In order to test the algorithms, a set of simulations are presented: the robot KUKA LBR iiwa is controlled in different cases, where fixed or dynamic obstacles interfere with its motion. Simulations are also used to estimate the required computational effort in order to verify the transferability to a real system.

This paper introduces an alternative method to design the path following controller of an under-actuated spherical mobile robot, which has a single pendulum structure its inside as a driving mechanism. The mechanism has an under-actuated problem; two inputs for the roll and pitch but no direct input for the yaw. In order to overcome this problem, the proposed method defines a virtual reference input for the heading direction. The virtual reference input works as a control input since it can be arbitrarily designed just like the reference input of a conventional system. The control scheme using the defined virtual reference input achieves the stabilization and path following control of the under-actuated spherical mobile robot without any additional control technique. The stability of the proposed control scheme is guaranteed by Lyapunov stability analysis, and simulation results are given to demonstrate its performance.

Wearable technology has been proposed as a potential tool to change the way of human life, such as the smart bracelet and the Google Glass. In the wearable technology, the inertial sensor has great significance in tracking the object movements. The paper focused on detecting the movements of user’s finger based on the inertial sensor to give the control signals. Firstly, the attitude matrix, which represented the transformation relation of carrier coordinate system and the navigation coordinate system, was obtained. Secondly, the attitude matrix was expressed based on the quaternions. Thirdly, the finger gesture was processed by the attitude matrix to get the attitude angle. Finally, the robot was controlled by attitude angle to make the moving action. The experimental results showed the detection of the finger movement is effective.

Fully mechanized mining face production involves complex geological conditions; mining pressure; gas, water, fire and other mining environments. The working face needs a shearer, hydraulic support, a scraper conveyor and other equipment for coordination. The deep integration of intelligent technology with factors such as "humans, machines, the environment, and management" in the workplace is the core content of intelligent coal mines. This paper puts forward an advanced framework for coal mining robot technology systems, including single robots, robotized equipment, robot clusters and unmanned systems. The framework clarifies the common key technologies of coal mining robot research and development and cross-integration with new technologies such as 5G, the industrial internet, big data, artificial intelligence, and digital twins to improve the autonomous and intelligent application of coal mining robots. By establishing a scientific and complete standard system for coal mining robots, we aim to achieve customized research and development and standardized production of various types of robots. A specific analysis was conducted on the research progress of common key technologies such as explosion-proof design, mechanical system innovation, power drive, intelligent sensing, positioning and navigation, and underground communication of coal mining robots. The current research and application status of various types of coal mining robots in China are summarized. A new direction for future coal mine robot research and development is proposed. Moreover, robotic mining systems should be promoted to enhance the overall intelligence level and mining efficiency of mining equipment. To develop human‒machine environment-integrated robots to improve the autonomy and collaboration level of coal mining robots. The digital twinning of the entire mine robot system should be accelerated, the normalized operation level of coal mine robots should be improved, research on coal mining robots, support robots, and transportation robots should be carried out, intelligence should be achieved in fully mechanized mining faces, and equipment support for fewer and unmanned fully mechanized mining faces should be provided. The practical process of implementing coal mining robotization has been summarized, and the technical and engineering feasibility of the coal mining machine population has been verified.

In large industrial plants, the trend is to move the position of the human to the area of service and diagnostics, in medium and smaller plants the trend is different and is mainly directed to the sphere of close cooperation between the human and the robotic system. This paper deals with the implementation of human-cooperating robots in manufacturing processes. The analytical part of the paper deals with theoretical knowledge, taking into account the latest trends in the subject area. To achieve a successful implementation of cobots based on the above-mentioned operating systems in manufacturing systems, it is necessary to pay attention specifically to the interfacing of the robotic operating system with the control systems of the manufacturing systems at the process level of the enterprise. Within the practical part, an algorithm with well-defined steps towards the successful implementation of cobots in holonic manufacturing processes is proposed. By setting up an experimental workstation in the laboratory, the proposed procedures are verified at the end of the paper. In the context of the implementation of collaborative robots in enterprises, the paper also discusses cloud computing. The creation of a design for the implementation of a collaborative robot with a human represents the missing link in the whole chain of commercial applications of the latest trends from the field of robotic systems in the industrial sphere.

Bipedal locomotion remains one of the major open challenges of humanoid robotics. The common approaches are based on simple reduced model dynamics to generate walking trajectories, often neglecting the whole-body dynamics of the robots. As motions in nature are often considered as optimal with respect to certain criteria, in this work we present an optimal control based approach that allows us to generate optimized walking motions using a precise whole-body dynamic model of the robot, in contrast with the common approaches. The optimal control problem is formulated to minimize a set of desired objective functions with respect to physical constraints of the robot and contact constraints of the walking phases. We apply the method with combinations of different objective criteria to the model of a reduced version of the iCub humanoid robot of 15 internal DOF. The obtained trajectories are executed on the real robot and we carry out a discussion on the differences between the outcomes of this approach with the classic approaches.

This paper presents experimental results of static and dynamic obstacle avoidance methods for a two-wheel mobile robot with independent control using a deep Q-learning (DQL) reinforcement learning algorithm. This is an alternative method that combines the Q-learning (QL) algorithm with a neural network. Neural networks in the DQL algorithm act as Q matrix table approximators for each pair (State - Action). The effectiveness of the proposed solution was verified through simulations, programming, and experimentation. This DQL algorithm is compared to the QL algorithm. First, the mobile robot communicated with the control script using the robot operating system (ROS). The mobile robot is code programmed using a Python in the ROS operating system combined with the DQL controller in Gazebo software. The mobile robot then performed experiments in a workshop with many different experimental scenarios. This DQL controller is improved in term of the computation time, convergence time, planning trajectory accuracy, and obstacles avoidance. Therefore, the DQL controller solved the path optimization problems for mobile robots better than the Q-learning controller.

This study introduces a cybernetic control and architectural framework for a robotic fish avatar operated by a human. The behavior of the robot fish is influenced by the electromyographic (EMG) signals of the human operator, triggered by stimuli from the surrounding objects and scenery. An deep artificial neural network (ANN) with perceptrons classifies EMG signals, discerning the type of muscular stimuli generated. The research unveils a fuzzy-based oscillation patterns generator (OPG) designed to emulate functions akin to a neural central pattern generator, producing coordinated fish undulations. The OPG generates swimming behavior as an oscillation function, decoupled into coordinated step signals, right and left, for a dual electromagnetic oscillator in the fish propulsion system. Furthermore, the research presents an underactuated biorobotic mechanism of the subcarangiform type, comprising a two-solenoid electromagnetic oscillator, an antagonistic musculoskeletal elastic system of tendons, and a multi-link caudal spine composed of helical springs. The biomechanics dynamic model and control for swimming, as well as the ballasting system for submersion and buoyancy, are deduced. Experimental results encompass EMG pattern recognition, OPG, and coordinated fish locomotion, with additional topics illustrated through numerical simulations.

This paper proposes the application of force-projecting bilateral control to a master-follower teleoperation system with a pneumatic manipulator on the follower side, and evaluates its effectiveness. The proposed method directly projects the operating force on the master side to the driving force on the follower side, eliminating the need for both position control and external force detection on the follower side, thereby solving the problem of low rigidity and response delay of pneumatic manipulators and providing highly stable sensor-less force presentation against variable environments. In this study, dynamic response analyses of a 1-DOF master-follower system were performed by numerical simulation using a linear system model, followed by experimental verification by implementing an actual system with an external force estimator. The results showed that the proposed force-projecting bilateral control has significantly higher positioning rigidity and better force control stability than the conventional force-reflecting bilateral control. A theoretical consideration was also given using equivalent transformation of force transfer functions to provide evidence for the high stability.

Research on bidirectional human-machine interfaces will enable the smooth interaction with robotic platforms in contexts ranging from industry to tele-medicine and rescue. This paper introduces a bidirectional communication system to achieve multisensory telepresence during the gestural control of an industrial robotic arm. We complement the gesture-based control by means of a tactile-feedback strategy grounding on a spiking artificial neuron model. Force and motion from the robot are converted in neuromorphic haptic stimuli delivered on the user’s hand through a vibro-tactile glove. Untrained personnel participated in an experimental task benchmarking a pick-and-place operation. The robot end-effector was used to sequentially press six buttons, illuminated according to a random sequence, and comparing the tasks executed without and with tactile feedback. The results demonstrated the reliability of the hand tracking strategy developed for controlling the robotic arm, and the effectiveness of a neuronal spiking model for encoding hand displacement and exerted forces in order to promote a fluid embodiment of the haptic interface and control strategy. The main contribution of this paper is in presenting a robotic arm under gesture-based remote control with multisensory telepresence, demonstrating for the first time that a spiking haptic interface can be used to effectively deliver on the skin surface a sequence of stimuli emulating the neural code of the mechanoreceptors beneath.

Keywords: Rehabilitation robot, position-force control, feed-forward control.

This paper proposes a multifunctional soft robotic gripper for a Dobot robot to handle sensitive products. The gripper is based on pneumatic network (PneuNet) bending actuators. In this work, two different models of PneuNet actuators have been studied, designed, simulated, experimentally tested, and validated using two different techniques (3D printing and molding) and three different materials: FilaFlex (3D printed), Elastosil M4601 and Dragonskin Fast 10 silicones (with molds). A new soft gripper design for the Dobot robot is presented, and a new design/production approach with molds is proposed to obtain the gripper's PneuNet multifunctional actuators. It also describes a new control approach that is used to control the PneuNet actuators and gripper function, using compressed air generated by a small compressor/air pump, a pressure sensor, a mini valve, etc., and executing on a low-cost controller board – Arduino UNO. This paper presents the main simulation and experimental results of this research work.

In an agricultural system, finding suitable watering, pesticide, and soil content to provide the right nutrients for the right plant is a mystery so far. Plants cannot speak and cannot ask which food they require. These problems can be addressed by applying intelligent (fuzzy logic) controllers to IoT devices in order to enhance communication between crops, ground mobile robots, aerial robots, and the entire farm system. The application of fuzzy logic in agriculture is a promising technology that can be used to optimize crop yields and reduce water usage. It was developed based on language and the air properties in the agricultural fields were formulated. The entire system was simulated in the MATLAB/SIMULINK environment with Cisco Packet Tracer integration. The inputs for the system were soil moisture sensors, temperature sensors, humidity sensors, and outputs were pump flow, valve opening, water level, and moisture in sounding. The obtained results were the output of opening valve, moisture in sound, pump flow rate, outflows, water level, and ADH values, which are 10.00000013 rad/sec, 34.72%, 4.494%, 0.025 m^3/sec, 73.31 cm^3, and 750 values respectively. The outflow rate increase indicates that the water is released from the tanks, and the control signal fluctuates, indicating that the valve is opening.

Exoskeleton robots have become a promising tool in neurorehabilitation, offering effective physical therapy and recovery monitoring. The success of these therapies relies on precise motion control systems. Although computed torque control based on inverse dynamics provides a robust theoretical foundation, its practical application in rehabilitation is limited by its sensitivity to model accuracy, making it less effective when dealing with unpredictable payloads. To overcome these limitations, this study introduces a novel model reference computed torque controller that accounts for parametric uncertainties while optimizing computational efficiency. A dynamic model of a seven-degree-of-freedom human lower limb exoskeleton is developed, incorporating a realistic joint friction model to accurately reflect the physical behavior of the robot. To reduce computational demands, the control system is split into two loops: a slower loop that predicts joint torque requirements based on input trajectories and robot dynamics, and a faster PID loop that corrects trajectory tracking errors. Coriolis and centrifugal forces are excluded from the model due to their minimal impact on system dynamics relative to their computational cost. Experimental results show high accuracy in trajectory tracking, and statistical analyses confirm the controller’s robustness and effectiveness in handling parametric uncertainties. This approach presents a promising advancement for improving the stability and performance of exoskeleton-based neurorehabilitation.

Fires pose a significant threat to human life and property. An autonomous fire detection and fighting robot has the potential to mitigate the challenges associated with firefighting. This paper presents the implementation of an autonomous fire detection and fighting robot equipped with sensors, algorithms, and actuators to detect, locate, and suppress fires autonomously. The robot's mechanical and electrical components were designed, prototyped, and tested in a controlled environment to evaluate its ability to navigate through obstacles, detect fires, and suppress them autonomously. The results show that the robot effectively detects and suppresses fires, making it a promising solution for firefighting applications. The study contributes to the development of autonomous robots for firefighting, enhancing the safety of firefighters and the effectiveness of firefighting operations.

This paper develops feasible control strategies and associated system responses to bring an autonomous front-axle bicycle robot from specified initial conditions to final conditions such that a specific performance index is minimized. To solve the problem, the following approach is used: The feasible controls derived from the normal equations of optimality are substituted into the state and the costate systems and form a combined control-free state-costate system which is vectorized to enable and ease the application of a numerical method. A computer program written in Matlab computer programming language, codes a fourth-order Runge-Kutta numerical method and then solve the combined state-costate system of ordinary differential equations. The obtained results are the feasible bicycle robot trajectory, the feasible state functions, the feasible costate functions and the feasible control functions. Associated Computational Simulations are designed and provided to persuade on the effectiveness and the reliability of the approach.

The paper presents the possibility of using KINECT v2 module to control an industrial robot by means of gestures and voice commands. It describes elements of creating software for off-line and on-line robot control. The application for KINECT module was developed in C# language in Visual Studio environment, while the industrial robot control program was developed in RAPID language in RobotStudio environment. The development of a two-threaded application in RAPID language allowed to separate two independent tasks for the IRB120 robot. The main task of the robot is performed in thread no. 1 (responsible for movement). Simultaneously working thread no. 2 ensures continuous communication with the KINECT system and provides information about the gesture and voice commands in real time without any interference in thread no. 1. The applied solution allows the robot to work in industrial conditions without negative impact of communication task on the time of robot’s work cycles. Thanks to the development of a digital twin of the real robot station, tests of proper application functioning in off-line mode (without using a real robot) were conducted. Obtained results were verified online (on the real test station). Tests of correctness of gesture recognition were carried out, the robot recognized all programmed gestures. Another test carried out was the recognition and execution of voice commands. A difference in the time of task completion between the actual and virtual station was noticed - the average difference was 0.67 s. The last test carried out was to examine the impact of interference on the recognition of voice commands. With a 10dB difference between the command and noise, the recognition of voice commands was equal to 91.43%. The developed computer programs have a modular structure, which enables easy adaptation to process requirements.

Purpose: The ongoing COVID-19 crisis has created the need for social distancing between medical staff and patients, therefore, healthcare robotics is increasingly important as regards infectious control. The purpose of this study was to design and fabricate a remote controlled transport robot that could provide an optimum technology base for developing countries, having dual functions of telepresence and delivery operations inside or outside buildings, is easy to assemble and also easily able to be cleaned using standard chemical agents.Methods: This machine was designed and fabricated to incorporate two main functions; delivery and telepresence. The robot consists of a base frame, DC motors for driving and steering systems, actuator motor for driving wheel elevation, Wi-Fi AP/Repeater, network camera, and a necessary a back-up power system.Results: This robot can be used both indoors and outdoors. It can carry loads of more than 80 kg. The machine can cross obstacles greater than 3 cm. It can be cleaned by disinfectant agents. An actuator motor can lift the driving wheels above the surface to prevent gear damage. Conclusion: This article demonstrates the concept of a healthcare telepresence and delivery robot that can provide distancing during the present COVID-19 crisis, using optimum technology for low and middle-income countries. In the future, the researcher should consider development of the delivery controls, combined with the telepresence system using the internet of things, to improve the navigation system, the manipulator system for supporting multi-floor transportation, and also other multi-functional purposes.

This paper aims at computing feasible control strategies and the corresponding feasible state trajectories to drive an autonomous rear-axle bicycle robot from a given initial state to a final state such that the total running cost is minimized. Pontryagin’s Minimum Principle is applied and derives the optimality conditions from which the feasible control functions, expressed as functions of state and costate variables, are substituted into the combined state-costate system to obtain a new free-control state-costate nonlinear system of ordinary differential equations. A computer program was written in Scilab to solve the combined state-costate system and obtain the feasible state functions, the feasible costate functions and the feasible control functions. Associated Computational Simulations were provided to show the effectiveness and the reliability of the approach.

Exoskeleton robots are a rising technology in industrial contexts to assist humans in onerous applications. Mechanical and control design solutions are intensively investigated to achieve a high performance human-robot collaboration (e.g., transparency, ergonomics, safety, etc.). However, the most of the investigated solutions involve high-cost hardware, complex design solutions and standard actuation. In the presented work, an industrial exoskeleton for lifting and transportation of heavy parts is proposed. A low-cost mechanical design solution is proposed, exploiting compliant actuation at the shoulder joint to increase safety and transparency in human-robot cooperation. A hierarchic model-based controller is then proposed (including the modeling of the compliant actuator) to actively assist the human while executing the task. An inner optimal controller is proposed for trajectory tracking, while an outer fuzzy logic controller is proposed to online deform the task trajectory on the basis of the human’s intention of motion. A gain scheduler is also designed to calculate the optimal control gains on the basis of the performed trajectory. Simulations have been performed in order to validate the performance of the proposed device, showing promising results. The prototype is under realization.

In this paper, a modular wire-actuated robotic arm was designed to improve the safety and adaptability of service robots during human-robot interaction. To raise the stiffness adjustment range of the robotic arm, a symmetric variable-stiffness unit was designed based on flexure, which had compact and simple structure, and lowly nonlinear stiffness-force relationship. In this paper, we focused on the research of the symmetric 1-DOF joint module. Based on the kinematics and stiffness analysis, the pose of the joint module could be adjusted by controlling the length of the wires, and the stiffness of the joint module could be adjusted by controlling the tension of the wires. Because of the actuation redundancy, the pose and stiffness of the joint module could be controlled synchronously. Furthermore, a directly method was proposed for the stiffness-oriented wire tension distribution problem of the 1-DOF joint module. A simulation was carried out to verify the proposed method.

This study presents a literature review focused on nonverbal communication in human-robot interaction (HRI) that involves service robots with social capabilities. We aim to list the types of robots used and nonverbal communication cues examined in the reviewed studies; and the main research objectives, participant characteristics, data collection methods, and primary findings of these studies. To achieve this, we conducted a literature review of 39 relevant open access academic papers published from 2006 to 2023 that examined the utilization of nonverbal cues by both humans and robots during HRI. The results suggest that enhancing the quality of communication between humans and service robots must be improved, while there are several aspects that require more thorough exploring, needed to strengthen robot self-efficacy, trust and trustworthiness in HRI or overcome cultural differences. The results emphasize the importance of nonverbal communication in shaping the dynamics of interactions between humans and service robots.

We present the design and overall development of an eight degrees of freedom (DOF) based Bioinspired Quadruped Robot (BiQR). The robot is designed with a skeleton made of cedar wood. The wooden skeleton is based on exploring the potential of cedar wood to be a choice for legged robots’ design. With a total weight of 1.19 kg, the robot uses eight servo motors that run the position control. Relying on the inverse kinematics, the control design enables the robot to perform the walk gait-based locomotion in a controlled environment. The robot has two main aspects: 1) the initial wooden skeleton development of the robot showing it to be an acceptable choice for robot design, 2) the robot’s applicability as a low-cost legged platform to test the locomotion in a laboratory or a classroom setting.

STRAS (Single access Transluminal Robotic Assistant for Surgeons) is a flexible robotic system based on the Anubis® platform of Karl Storz for application to intra-luminal surgical procedures. It consists of three cable-driven systems, one endoscope serving as guide and two inserted instruments. The flexible and bendable instruments have three degrees of freedom and can be teleoperated by a single user via two specially designed master interfaces. In this research, a pair of specific sensor gloves, which ergonomically fit to the master handles of the system was designed and the forces applied by one expert and one novice user during system-specific task execution in a simulator task (4-step-pick-and-drop) were compared. The results show that user expertise is not only reflected by shorter task execution times but also, more importantly, by specific differences in handgrip force profiles for specific sensor locations on anatomically relevant parts of the fingers and hand controlling the surgical instruments of the robotic master/slave system.

The paper delineates the developed vision system of the UR5 cobot and the operating algorithm of the robotic quality control station. The hardware-software architecture of the developed robotic station was shown, consisting of a UR5 cobot equipped with a web camera and a stationary industrial camera with a lighting system. Image processing and analysis algorithms were described, the method of control and communication between the station components was discussed, and two operating scenarios were presented as a single robotic station and a robotic line. Based on the results obtained, the level of measurement noise, accuracy, and repeatability of the developed vision system were estimated.

Modelling errors, robust stabilization/tracking problems under parameter and model uncertainties complicate the control of the flexible underactuated systems. Chattering-free sliding-mode based input-output control law realizes robustness against the structured and unstructured uncertainties in the system dynamics and avoids excitation of unmodeled dynamics. The main purpose is to propose a robust adaptive solution for stabilizing and tracking direct-drive (DD) flexible robot arms under parameter and model uncertainties, as well as external disturbances. A lightweight robot arm subject to external and internal dynamic effects was taken into consideration. The challenges are compensating actuator dynamics with the inverter switching effects and torque ripples, stabilizing the zero dynamics under parameter/model uncertainties and disturbances while precisely track the predefined reference position. The precise control of this kind of system demands an accurate system model and knowledge of all sources that excite unmodeled dynamics. For this purpose, equations of motion for a flexible robot arm were derived and formulated for the large motion via Lagrange’s method. The goals were determined to achieve high-speed, precise position control, and satisfied accuracy by compensating the unwanted torque ripple and friction that degrades performance through an adaptive robust control approach. The actuator dynamics and their effect on the torque output were investigated due to the transmitted torque to the load side. The high-performance goals, precision&robustness issues, and stability concerns were satisfied by using robust-adaptive input-output linearization-based control law combining chattering-free sliding mode control (SMC) while avoiding the excitation of unmodeled dynamics.

The implementation of a progressive rehabilitation training model to promote patients’ motivation efforts can greatly restore the damaged central nervous system function in patients. The patients’ active engagement can be effectively stimulated by assist-as-needed (AAN) robot rehabilitation training. However, its application in robotic therapy has been hindered by a simple determination method of robot assisted torque which focuses on the evaluation only of the affected limb's movement ability. Moreover, the expected effect of assistance depends on the designer, which deviates from the patient's expectations, and its applicability to different patients is deficient. In this study, we propose a control method with personalized treatment features based on the idea of estimating and mapping the stiffness of the patient’s healthy limbs. This control method comprises an interactive control module in the task-oriented space based on the quantitative evaluation of motion needs and an inner loop position control module for the pneumatic swing cylinder in the joint space. An upper limb endpoint stiffness estimation model is constructed and a parameter identification algorithm is designed. The upper limb endpoint stiffness which characterizes the patient's ability to complete training movements is obtained by collecting surface electromyographic (sEMG) signals and human-robot interaction forces during patient movement. Then the motor needs of the affected limb when completing the same movement are quantified based on the performance of the healthy limb. A stiffness mapping algorithm is designed to dynamically adjust the rehabilitation training trajectory and auxiliary force of the robot based on the actual movement ability of the affected limb, achieving AAN control. Experimental studies were conducted on a self-developed pneumatic upper limb rehabilitation robot, and the results showed that the proposed AAN control method can effectively estimate the patient's movement needs and achieve progressive rehabilitation training. The rehabilitation training robot that simulates the movement characteristics of the patient's healthy limbs drives the affected limb, making the intensity of the rehabilitation training task more in line with the patient's pre-morbid limb use habits, and also beneficial for the consistency of bilateral limb movements.

This paper aims at computing feasible control strategies and the corresponding feasible state trajectories to drive an autonomous rear-axle bicycle robot from a given initial state to a final state such that the total running cost is minimized. Pontryagin’s Minimum Principle is applied and derives the optimality conditions from which the feasible control functions, expressed as functions of state and costate variables, are substituted into the combined state-costate system to obtain a new free-control state-costate nonlinear system of ordinary differential equations. A computer program was written in Scilab to solve the combined state-costate system and obtain the feasible state functions, the feasible costate functions and the feasible control functions. Associated Computational Simulations were provided to show the effectiveness and the reliability of the approach.

Skid steer mobile robots are widely used in indoor and outdoor applications. However, accurate trajectory tracking control for this kind of robot is quite challenging due to the uncertainties arising from the complex behavior of frictional force, external disturbances, and undergoing fluctuations in the instantaneous center of rotation (ICR) during turning maneuvers. The uncertainties directly disturb velocities and make it impossible for the robot to track the command velocities, thus making the SSMR unable to follow the reference path. This paper proposes a nonsingular terminal sliding mode control (NTSMC) based on backstepping for a 4-wheel skid steer mobile robot to cope with the aforementioned challenges. The strategy seeks to mitigate the impact of external disturbances and model uncertainties by developing an adaptive law to estimate the integrated lumped outcome. Then, the finite time stability of the closed-loop system is proven using Lyapunov’s theory. The designed NTSMC input is continuous and has no noticeable chattering problem. It has also been noted from the analysis that the proposed control strategy is strongly robust against disturbance and modeling uncertainties. The proposed control scheme demonstrates effective trajectory tracking performance in the presence of disturbance and modeling uncertainties through simulations.

As the global population rapidly ages with longer life expectancy and declining birth rates, the need for healthcare services and caregivers for older adults is increasing. Current research envisions addressing this shortage by introducing domestic service robots to assist with daily activities. The successful integration of robots as domestic service providers in our lives requires them to possess efficient manipulation capabilities, provide effective physical assistance, and have adaptive control frameworks that enable them to develop social understanding during human-robot interaction. In this context, human factors, especially quantifiable ones, represent a necessary component. The objective of this paper is to conduct an unbiased review encompassing studies on human factors studied in research involving physical interactions and strong manipulation capabilities. We identified the prevalent human factors in physical human-robot interaction (pHRI), noted the factors typically addressed together and determined the frequently utilized assessment approaches. Additionally, we gathered and categorized proposed quantification approaches based on measurable data for each human factor. We also formed a map of common contexts and applications addressed in pHRI for a comprehensive understanding and easier navigation of the field. We found out that most of the studies in direct pHRI (when there is direct physical contact) focus on social behaviors with belief being the most commonly addressed human factor type. Task collaboration is moderately investigated, while physical assistance is rarely studied. In contrast, indirect pHRI (when the physical contact is mediated via a third item) studies often involve industrial settings, with physical ergonomics being the most frequently investigated human factor. More research is needed on human factors in direct and indirect physical assistance applications, including studies that combine physical social behaviors with physical assistance tasks. We also found that while the predominant approach in most studies involves the use of questionnaires as the main method of quantification, there is a recent trend that seeks to address quantification approaches based on measurable data.

This paper develops a methodology to control the navigation of an autonomous ship robot from an initial state to a final. To solve the problem the following approach is used: The ship robot system is modelled as a control system of six ordinary differential equations involving six state variables and three control variables. After having computed the system Hamiltonian, the feasible controls for optimality are derived from the normal equations of optimality as functions of the state and costate variables. Such controls are substituted into the state and the costate equations and give a combined control-free state-costate system of ordinary differential equations which is solved numerically by using a developed Matlab computer program. Associated computational simulations are designed and provided to show the reliability of the approach.

The idea of developing a robot controlled by iris movement to assist physically disabled individuals is indeed innovative and has the potential to significantly improve their quality of life. This technology can empower individuals with limited mobility and enhance their ability to interact with their environment. Disability of movement has huge impact on the life of physically disabled people. Therefore, there is need to develop a robot which can be controlled using iris movement. The main idea of this work revolves around iris recognition from an eye image, specifically identifying the centroid of the iris. The centroid's position is then utilized to issue commands to control the robot. This innovative approach leverages iris movement as a means of communication and control, offering a potential breakthrough in assisting individuals with physical disabilities. The proposed method aims to improve the precision and effectiveness of iris recognition by incorporating advanced segmentation techniques and fuzzy clustering methods. The fast gradient filters using a fuzzy inference system (FIS) is employed to separate the iris from its surroundings. Then, the bald eagle search (BES) algorithm is employed to locate and isolate the iris region. Subsequently, the Fuzzy KNN algorithm is applied for the matching process. This combined methodology aims to improve the overall performance of iris recognition systems by leveraging advanced segmentation, search, and classification techniques. The results of the proposed model are validated using True Success Rate (TSR) and compared to other existing models. The results highlight the effectiveness of the proposed method for the 400 tested images representing 40 people.

This paper describes design of experimental methodology developed to measure the working properties of accuracy of the path traversed by a collaborative robot. The methodology proposed here uses a collaborative robot and a laser measuring system Gepard from Raytec. The main parts of the measuring chain and the ISO 9283 standard are described. The proposed experimental methodology should examine working properties of industrial robots, such as the properties of position and path. The focus of this paper lies on the path accuracy of robots. Currently, the interest in this topic is on the rise and the measuring systems capable of recording this parameter are too costly. This paper focuses on experimental measuring of the path properties, describing them in more detail. The measuring and results were processed in the software tool developed for Gepard.

In this article, the research team has systematically developed a method to model the kinematics and dynamics of a 3-wheeled robot subjected to external disturbances and sideways wheel sliding. These models will be used to design control laws that compensate for wheel slippage, model uncertainties, and external disturbances. These are control algorithms developed based on Dynamic Surface Control (DSC). Adaptive trajectory tracking DSC algorithm using fuzzy logic system (AFDSC) and radial neural network (RBFNN) with fuzzy logic system to overcome the disadvantages of DSC and expand the application domain for wheeled Mobile Robots (WMR). However, this Adaptive Fuzzy Neural Network Dynamic Surface Control (AFNNDSC) adaptive controller ensures the closed system is stable and follows the preset trajectory in the presence of wheel slippage model uncertainty and is affected by significant amplitude disturbances. The stability and convergence of the closed-loop system are guaranteed based on the Lyapunov analysis. The AFNNDSC adaptive controller is evaluated by simulation on MATLAB/Simulink software and in a steady state. The maximum position error on the right wheel and left wheel is 0.000572 (m) and 0.000523 (m), and the angular velocity tracking error in the right and left wheels of the control method is 0.000394 (rad/s). The experimental results show the correctness of the theoretical analysis, the effectiveness of the proposed controller, and the possibility of practical application.

Robot Operating System 2 (ROS 2) is a robotic software that uses a set of Quality of Service (QoS) policies to manage the quality of robot data transmissions in a network, such as the RELIABLE and KEEP_LAST options. In ROS 2 node communication, the RELIABLE connection guarantees that all message data can be properly sent from the publisher to the subscriber. However, strict reliability is not guaranteed if the RELIABLE connection uses the KEEP_LAST option to transmit the robot data in the publish-subscribe communication. This study aims to analyze the efficiency of local cache, cache control, and QoS balancing optimization to improve ROS 2 node communication when using the RELIABLE and KEEP_LAST options to transmit multi-robot data in Aggregated Robot Processing (ARP) architecture. Our idea in local cache and cache control is to streamline the sensor data output before processing it when the sensor device produces the data with the same value in a row. Furthermore, QoS balancing optimization aims to balance the DEPTH and DEADLINE QoS configuration to determine the rates and buffer size in ROS 2 node communication. This study shows that combining local cache and QoS balancing optimization improves multi-robot data transmission and cooperation in ARP architecture.

Designing and development of agricultural robot is always a challenging issue, because of robot intends to work an unstructured environment and at the same time, it should be safe for the surrounded plants. Therefore, traditional robots cannot meet the high demands of modern challenges, such as working in confined and unstructured workspaces. Based on current issues, we developed a new tomato harvesting wire-driven discrete continuum robot arm with a flexible backbone structure for working in confined and extremely constrained spaces. Moreover, we optimized a tomato detaching process by using newly designed gripper with passive stem cutting function. Moreover, by designing the robot we also developed ripe tomato recognition by using machine learning. This paper explains the proposed continuum robot structure, gripper design, and development of tomato recognition system.

This study observes, interprets, and analyses the knowledge production in the research field of Human–Robot Interaction (HRI). It intends to foreground the hidden assumptions that are often taken for granted when roboticist design and conduct their research. By doing so, this study demonstrates how these assumptions influence the result of their research. Based on data collected through sociological field observation, this study argues that the current practise in HRI research is highly anthropocentric. In short, the robots are designed to be like human instead of for human. Therefore, the human–robot relationship embodies the existing power relations between human beings. These relations generate inequality, hierarchy, and dominance, which are the opposite of the common imagination of the robotised future among roboticists. For the purpose of enabling the robotised future closer to their ideal, this study suggests that HRI researchers to go beyond the conventional methodology, to allow a human–robot relationship that realises reciprocity.

The integration of Augmented Reality (AR) into Human-Robot Interaction (HRI) represents a significant advancement in collaborative technologies. This paper provides a comprehensive review of AR applications within HRI, emphasizing their role in enhancing collaboration, trust, and safety. By aggregating findings from numerous studies, this research highlights key challenges, including the need for improved situational awareness, enhanced safety, and more effective communication between humans and robots. A framework developed from the literature is presented, detailing the critical elements of AR necessary for advancing HRI. The framework outlines effective methods for continuously evaluating AR systems for HRI. This structured approach focuses on enhancing collaboration and safety, with a strong emphasis on integrating best practices from Human-Computer Interaction (HCI) centered around user experience and design.

Depictions of robots as romantic partners for humans are frequent in popular culture. As robots are becoming part of human society, they gradually assume the role of partners for humans wherever necessary: as assistants, collaborators, or companions. Companion robots are sup-posed to provide social contact to those humans who could not have it otherwise. These com-panion robots are usually not designed to fulfill one of the most important human needs: the one for romantic and intimate contact. Human-robot intimacy remains a vastly unexplored ter-ritory. In this article, we review the state-of-the-art research in intimate robotics. We discuss major issues limiting acceptance of robots as intimate partners, public perception of robots in in-timate roles, and the possible influence of cross-cultural differences in these domains. We also discuss possible negative effects human-robot intimacy may have on human-human contact. Most importantly, we propose a new term “Intimate companion robots” to reduce the negative connotations of other terms used so far and improve the social perception of research in the domain. With this article, we provide an outlook on prospects for the development of intimate companion robots, considering the specific context of their use.

The use of new assistive technologies in general, and Socially Assistive Robots (SAR) in particular is becoming increasingly common for supporting people’s health and well-being. However, it still faces many issues regarding long-term adherence, acceptability and utility. Most of these issues are due to design processes that insufficiently take into account the needs, preferences and values of intended users. Other issues are related to the currently very limited amount of long-term evaluations, performed in real world settings, for SAR. This study presents the results of two regional projects that consider as a starting hypothesis that the assessment in controlled environments and/or with short exposures may not be enough in the design of a SAR deployed in a retirement home and the necessity of designing for and with users. Thus, the proposed methodology has focused in use cases definitions that follow a human-centred and participatory design approach. The main goals have been facilitating system acceptance and attachment by involving stakeholders in the robots design and evaluation, overcoming usage barriers and considering user’s needs integration. The implementation of the first use case deployed and the two-phase pilot test performed in the retirement home are presented. In particular, a detailed description of the interface re-design process based on improving a basic prototype with users’ feedback and recommendations is presented together with main results of a formal evaluation that has highlighted the impact of changes and improvements addressed in the first redesign loop of the system.

Collaborative robotics is a major topic in current robotics research posing new challenges, especially in Human-Robot Interaction. The crucial aspect in this area of research focuses on understanding the behavior of robots when engaging with humans, where reinforcement learning is a key discipline that allows us to explore sophisticated emerging reactions. This review aims to delve into the relevance of different sensors and techniques, with special attention to EEG (electroencephalography data on brain activity) and its influence on the behavior of robots interacting with humans. In addition, mechanisms available to mitigate potential risks during the experimentation process such as virtual reality will also be addressed. In the final part of the paper, future lines of research combining the areas of collaborative robotics, reinforcement learning, virtual reality and human factors will be explored, as this last aspect is vital to ensure safe and effective Human-Robot Interactions.

Traditional end-effector robots for arm rehabilitation are usually attached a­t the hand, primarily focusing on coordinated multi-joint training. Therapy at an individual joint level of the arm for severely impaired stroke survivors is not always possible with existing end-effector robots. The Arm Rehabilitation Robot (AREBO)—an end-effector robot—was designed to provide both single and multi-joint assisted training while retaining the advantages of traditional end-effector robots, such as ease of use and cost-effectiveness (compared to exoskeletons). This work presents the design, optimization, and characterization of AREBO for training single-joint movements of the arm. The AREBO has three actuated and three unactuated degrees of freedom, allowing it to apply forces in any arbitrary direction at its endpoint and self-align to arbitrary orientations within its workspace. The AREBO’s link lengths were optimized to maximize its workspace and manipulability. The AREBO provides single-joint training in both unassisted and adaptive weight support modes using a human arm model to estimate the human arm's kinematics and dynamics without using additional sensors. The characterization of the robot’s controller and the algorithm for estimating the human arm parameters were performed using a two degrees of freedom mechatronic model of the human shoulder joint. The results demonstrate that: (a) the movements of the human arm can be estimated using a model of the human arm and robot’s kinematics, (b) the AREBO has similar transparency to that of existing arm therapy robots in the literature, and (c) the adaptive weight support mode control can adapt to different levels of impairment in the arm. This work demonstrates how an appropriately designed end-effector robot can be used for single-joint training, which can be easily extended to multi-joint training. Future work will focus on the evaluation of the system on patients with any neurological condition requiring arm training.

This paper presents ROSGPT, an innovative concept that harnesses the capabilities of large language models (LLMs) to significantly advance human-robot interaction. We develop ROSGPT as a ROS2 package that seamlessly integrates ChatGPT with ROS2-based robotic systems. The core idea is to leverage prompt engineering with LLMs, specifically ChatGPT, utilizing its unique properties such as ability eliciting, chain-of-thought, and instruction tuning. The concept employs ontology development to convert unstructured natural language commands into structured robotic instructions specific to the application context through prompt engineering. We capitalize on LLMs' zero-shots and few-shots learning capabilities by eliciting \textit{structured} robotic commands from \textit{unstructured} human language inputs. To demonstrate the feasibility of this concept, we implemented a proof-of-concept that integrates ChatGPT with ROS2, showcasing the transformation of human language instructions into spatial navigation commands for a ROS2-enabled robot. This versatile concept can be easily adapted to various other robotic missions. ROSGPT serves as a new stride towards Artificial General Intelligence (AGI) and paves the way for the robotics and natural language processing communities to collaborate in creating novel, intuitive human-robot interactions. The open-source implementation of ROSGPT on ROS 2 is available on GitHub.

In this work we report on our effort to design and implement an early introduction to basic robotics principles for children at kindergarten age. The humanoid robot Pepper, which is a great platform for human-robot interaction experiments, was presenting the lecture by reading out the contents to the children making use of its speech synthesis capability. One of the main challenges of this effort was to explain complex robotics contents in a way that pre-school children could follow the basic principles and ideas using examples from their world of experience. A quiz in a Runaround-game-show style after the lecture activated the children to recap the contents they acquired about how mobile robots work in principle. Besides the thrill being exposed to a mobile robot that would also react to the children, they were very excited and at the same time very concentrated. What sets apart our effort from other work is that part of the lecturing is actually done by a robot itself and that a quiz at the end of the lesson is done using robots as well. To the best of our knowledge this is one of only few attempts to use Pepper not as a tele-teaching tool, but as the teacher itself in order to engage pre-school children with complex robotics contents. We got very positive feedback from the children as well as from their educators.

Global teacher shortage is a serious concern with grave implications for the future of education. This calls for novel ways of addressing teacher roles. The economic benefits of tireless labour inspires the need for teachers who are unlimited by natural human demands, highlighting consideration for the affordances of robotics and Artificial Intelligence in Education (AIED) as currently obtainable in other areas of human life. This however demands designing robotic personalities that can take on independent teacher roles despite strong opinions that robots will not be able to fully replace humans in the classroom of the future. In this paper, we argue for a future classroom with independent robot teachers, highlighting the minimum capabilities required of such personalities in terms of personality, instructional delivery, social interaction and affect. We describe our project on the design of a robot teacher based on these. Possible directions for future system development and studies are highlighted.

The development of intelligent medical service robots for patient care presents significant chal-lenges, particularly in integrating diverse knowledge sources and enabling robots to autono-mously perform tasks in dynamic and unpredictable healthcare environments. This study in-troduces a novel framework that combines large language models (LLMs) with healthcare-specific knowledge and robotic operations to enhance autonomous task execution for a Robotic Health Attendant (RHA). Utilizing OpenAI’s ChatGPT, the RHA processes structured information about patient care protocols and unstructured human inputs to generate context-aware robot actions. A prototype system was tested in a simulated patient room where the RHA successfully performed both simple individual actions and complex tasks involving the execution of multiple actions, based on real-time dialogues with the LLM and predefined task specifications. The results demonstrate the potential of LLMs to reduce the reliance on hardcoded logic and provide healthcare professionals with the ability to interact with robotic systems through natural lan-guage.

Objectives: In order to solve the problem that most of the existing research focuses on the binary tactile attributes of objects,which ignores the tactile attribute strength and category recognition,an attribute strength and category recognition method based on convolutional neural network matrix-label is proposed. Methods:Firstly,in the data preparation stage,we preprocess the raw data and determine the matrix labels to build the haptic dataset.Secondly,in the feature extraction stage,we fuse the haptic data of two fingers and use the convolutional neural network to extract the attribute strength features.Finally,in the attribute strength and category recognition stage,all channel haptic data is fused to predict the attribute strength and category.Results:We compared with the multi-label convolutional neural network method in terms of elastic strength,hardness strength and category,and compared the attribute strength recognition capabilities of the two methods using novel objects outside the haptic dataset.The results show that the accuracy of the last 20 iterations of the matrix-label method has an average elastic strength of 96.73%,hardness strength of 97.34%,and category of 96.67%.The performance is better.When the Euclidean distance between the prediction of the novel object and the real label is less than 1,the accuracy of the elastic strength is best to reach 100%,and the hardness strength is best to reach 100%.The performance is better. Conclusions:The effectiveness of the method has been verified.Comparing with the convolutional neural network method,our method can effectively recognize the attribute strength and category of objects.

The object of this research is designing of new robot-to-robot communication system working in the middle of highway/roads to support mobile safety for approaching vehicles. The result of research project directs to a group of safety robot devices which induce a vehicle on a bypass route, as a vehicle guidance method using the same, and a vehicle safety guidance system. According to an embodiment of the present invention, a safety device includes a detector configured to detect a vehicle approaching the safety device, and an image projector configured to project an image onto a road surface approaching the vehicle when the detector recognizes an approach of the vehicle. It can include. According to the present invention, when it is necessary to guide the vehicle to the bypass route, the driver of the vehicle can grasp the detour route in time and move the vehicle to the next lane.

The important characteristic that could assist in autonomous navigation is the ability of a mobile robot to concurrently construct a map for an unknown environment and localize itself within the same environment. This computational problem is known as Simultaneous Localization and Mapping (SLAM). In literature, researchers have studied this approach extensively and have proposed a lot of improvement towards it. More so, we are experiencing a steady transition of this technology to industries. However, there are still setbacks limiting the full acceptance of this technology even though the research had been conducted over the last 30 years. Thus, to determine the problems facing SLAM, this paper conducted a review on various foundation and recent SLAM algorithms. Challenges and open issues alongside the research direction for this area were discussed. However, towards addressing the problem discussed, a novel SLAM technique will be proposed.

Phenotypic studies require large datasets for accurate inference and prediction. Collecting plant data in a farm can be very labor intensive and costly. This paper presents the design, architecture (hardware and software) and deployment of a distributed modular agricultural multi-robot system for row crop field data collection. The proposed system has been deployed in a soybean research farm at Iowa State University.

This brief essay explores both the social and biological dimensions of human sexuality in light of the possibility of a substantial commerce in sexually-enabled robots, and concludes with some potentially strategic considerations for those who find themselves involved with their design, production, and/or marketing.

The combination of humans’ cognitive skills and dexterity with the endurance and repeatability of robots is a promising approach to modern assembly. However, planning an assembly sequence and efficiently allocating tasks between humans and robots is a manual, complex, and time-consuming challenge. This work presents a framework named “Extract-Enrich-Assess-Plan-Review" that facilitates holistic planning of human-robot assembly processes. The framework uses heterogeneous data sources to feed a planning algorithm that generates assembly sequences according to various boundary conditions such as resource capability, part dependency, sequencing, and adaptability to human behavior. An expert remains in the loop to enrich the data, review, and modify the automatically generated sequences. As an output, the framework creates assembly sequences with different ways in which humans and robots work together that can be selected depending on the purpose of the subsequent use. For our experimental results, we compare the achieved degree of automation using three different CAD formats. We also demonstrate and analyse multiple assembly sequence plans that are generated by our system. Those assembly plans incorporate different human-robot interaction modalities that are synchronised, cooperative, or collaborative.

The real challenge in Human Robot Interaction (HRI) is to build machines capable of perceiving human emotions so that robots can interact with humans in a proper manner. It is well known from the literature that emotion varies accordingly to many factors. Among these, gender represents one of the most influencing one, and so an appropriate gender-dependent emotion recognition system is recommended. In this paper, a two-level hierarchical Speech Emotion Recognition (SER) system is proposed: the first level is represented by the Gender Recognition (GR) module for the speaker’s gender identification; the second is a gender-specific SER block. Specifically for this work, the attention was focused on the optimisation of the first level of the proposed architecture. The system was designed to be installed on social robots for hospitalised and living at home elderly patients monitoring. Hence, the importance of reducing the software computational effort of the architecture also minimizing the hardware bulkiness, in order for the system to be suitable for social robots. The algorithm was executed on the Raspberry Pi hardware. For the training, the Italian emotional database EMOVO was used. Results show a GR accuracy value of 97.8%, comparable with the ones found in literature.

Estimation and planning play a vital role in the construction of an autonomous navigation framework. However, these problems are often considered separately, while planning gives robot a free-collision path towards the desired goal, estimation algorithm presents the executed trajectory in the sense that it has to be closed to the ground truth path as much as possible. Recently, a unified probabilistic framework, which supports solving these problems simultaneously, dubbed STEAP has been proposed. Nevertheless, its current version is only designated for an omni wheels robot, which allows robot to move and turn in vertical direction. Differential drive robot, on the other hand, though limited to move along only one direction, has been used in various situations due to its flexibility and lower cost in hardware designing. Thus, in this extension, our aim is to control a differential drive robot via STEAP. Moreover, in a more complicated environment such as labyrinth or maze, the original STEAP sometimes fails to find a path. Indeed, this problem is mainly caused by the poor initialization and the non-linearity in optimizer constraints. In our implementation, instead of dealing with these constraints, we employ a global planner algorithm such as Dijkstra or RRT to treat STEAP as an effective local planner module that focus on following the global path. Consequently, the experimental results show that the extended STEAP not only able to navigate a differential drive robot but also in a more complicated and unstructured environment.

Robot workpiece machining is interesting in industry since it offers some advantages, such as higher flexibility in comparison with the conventional approach based on the CNC technology. However, in recent years we have been facing a strong progressive shift to custom based manufacturing and low volume/high mix production, which require a novel approach to automation by the employment of collaborative robotics. However, collaborative robots feature only limited motion capability, to provide safety in cooperation with human workers. Thus, it is highly necessary to perform more detailed robot task planning to ensure its feasibility and optimal performance. In this paper, we deal with the problem of studying kinematic robot performance in the case of such manufacturing tasks, where the robot tool is constrained to follow the machining path embedded on the workpiece surface at a prescribed orientation. The presented approach is based on the well-known concept of manipulability, although the latter suffers from physical inconsistency due to mixing different units of linear and angular velocity in a general 6 DOF task case. Therefore, we introduce the characteristics of the workpiece surface constraint in the robot kinematic analysis, that enables evaluation of its available velocity capability in a reduced dimension space. Such constrained robot kinematics transform the robot`s task space to a two-dimensional surface tangent plane, and the manipulability analysis may be limited to the space of linear velocity only. Thus, the problem of physical inconsistency is avoided effectively. We show the theoretical derivation of the proposed method, which was verified by numerical experiments.

Wire-driven hyper-redundant continuum manipulators are gaining more popularity and finding more applications in industry and in minimally invasive surgery. Unlike traditional rigid link manipulators, continuum robots with a flexible backbone structure are able to work in a highly constrained workspace and in an unstructured environment. However, in spite of a possible wide range of reachability, continuum manipulators have some issues related to payload capacity, accuracy and control. Therefore, in this research, we propose a novel hyper-redundant continuum robot with a passive sliding disc mechanism to improve payload capacity and accuracy. To prove the sliding mechanism concept, we demonstrate a comparison analysis with a conventional non-sliding continuum robot arm in a payload test, a bending test and a reachability test. Moreover, with this novel design, we are proposing robot kinematics and kinetic formulation and simulation results to validate the effectiveness of the sliding disc mechanism.

Background: The Micro Hand S robot is the first domestically produced surgical robot that has entered clinical use in China, and this is the first report of its application in colon cancer. Objective: This study aimed to validate the safety and efficacy of the domestically produced Chinese minimally invasive Micro Hand S surgical robot system in complex surgery, such as robotic complete mesocolic excision (R-CME). Methods: From March 2018 to December 2018, 30 patients with right hemicolon cancer underwent R-CME with the Micro Hand S robot system. The operative findings, morbidities, oncological findings and unique characteristics were summarizedwere analyzed. Result: 12 patients with right hemicolon cancer and 18 patients with sigmoid colon cancer underwent RCME with the Micro Hand S robot system. During the study period, the median operative duration was 209 (range, 180-255) min, and the median estimated blood loss volume was 35 (range, 25-75) ml. The median number of lymph nodes harvested was 42 (21-77), and the median postoperative hospital stay was 5 (range, 4-7) days. According to the Clavien-Dindo classification, there were no severe complications except for 7 cases of grade I complications and 5 cases of grade II complications. The conversion rate for all operations was 0%. There were no cases of 30-day readmission or 30-day mortality. Conclusion: Clinical application of domestically produced Chinese minimally invasive surgical robot system “Micro Hand S ” in selected colon cancer patients is technically feasible and safe.

Background: The Micro Hand S robot is the first domestically produced surgical robot that has entered clinical use in China, and this is the first report of its application in colon cancer.Objective: This study aimed to validate the safety and efficacy of the domestically produced Chinese minimally invasive Micro Hand S surgical robot system in complex surgery, such as robotic complete mesocolic excision (R-CME).Methods: From March 2018 to December 2018, 30 patients with right hemicolon cancer underwent R-CME with the Micro Hand S robot system. The operative findings, morbidities, oncological findings and unique characteristics were summarizedwere analyzed.Result: 12 patients with right hemicolon cancer and 18 patients with sigmoid colon cancer underwent RCME with the Micro Hand S robot system. During the study period, the median operative duration was 209 (range, 180-255) min, and the median estimated blood loss volume was 35 (range, 25-75) ml. The median number of lymph nodes harvested was 42 (21-77), and the median postoperative hospital stay was 5 (range, 4-7) days. According to the Clavien-Dindo classification, there were no severe complications except for 7 cases of grade I complications and 5 cases of grade II complications. The conversion rate for all operations was 0%. There were no cases of 30-day readmission or 30-day mortality. Conclusion: Clinical application of domestically produced Chinese minimally invasive surgical robot system “Micro Hand S ” in selected colon cancer patients is technically feasible and safe.

Walking of humanoid robots is dependent on precise tracking of the center of gravity and foot trajectories. Trajectory tracking is achieved by mobilizing the robot joints to produce the correct trajectory. Errors are being occurred because of assumptions on tracking the center of gravity and the foot trajectories. In this study, a numerical algorithm has been developed that produces an exact and single kinematic solution in which the center of gravity and foot trajectories can be tracked with the desired precision. The effectiveness of the algorithm was examined with a dynamic simulation and compared with the method given in the literature The main highlight of this study, using the presented algorithm, the robot can walk even if the position of its center of gravity is lower than its hips, resulting tracking error was smaller than reported in the literature.

Condition monitoring of industrial robots has the potential to decrease downtimes in highly automated production systems. We suggest a new health indicator based on vibration data measurements and compare its performance with state-of-the-art health indicators regarding different criteria. This evaluation is based on different data sets from robot test rigs. We find that the proposed health indicator can detect different faults, has low temperature sensitivity and works in instationary velocity regimes. A discussion of the validity of the results rounds up our contribution.

A nuclear reactor leak is undesirable and unpredictable occurrence in the plant of nuclear energy generation. For this reason, an accurate equipment is needed to inspect and supervise reactors. There are two kind of reactors for research and industry reactors, both of them are needed to inspect. Concern to inspection, regularly check is needed to ensure reactor conditions are always safe to operate. For that reason, an application of advanced technology for detecting leaks is priority. In this research, we are using underwater robot to be implemented. Using the robot is able to detect periodically, continuously with accurate reports to the operator or reactor supervisor. Furthermore, Underwater Robot namely Robaru, with 4 propellers equipped at the robot, Robaru can move on 3 axes x, y and z and rotate. The use of cameras, as well as temperature measurements to obtain data when conducting inspections of the reactor. The survey method used is direct observation to detect leaks. The robot is at a certain distance by following a predetermined connection or path. The robot has successfully performed a good check with an accurate level of positioning accuracy.

The ethics of invertebrate research have largely been ignored compared to the consideration of higher order animals, but more recent focus has questioned this trend. Using biohybrid robotic jellyfish as a case study, we examine the ethical considerations of invertebrate work and provide recommendations for future guidelines. This paper starts with an overview of philosophical views of animal ethics, the current state of knowledge for invertebrate pain and nociception, and current ethical guidelines. Next, we delve into the case study and analogous precedents. Specifically, in prior studies, we developed biohybrid robotic jellyfish, which modified live moon jellyfish with microelectronic swim controllers for future applications in ocean monitoring. Although jellyfish possess no central nervous system, pain receptors, or nociceptors, we closely monitored their stress responses, using the precautionary and minimization principles in consideration of the 4Rs: reduction, replacement, refinement, and reproducibility. We also discuss ethical considerations related to our studies and suggest that public opinion of invertebrate research relies heavily on repugnance, including fears of ‘playing God’ or limiting the ‘free will’ of animals. These issues are also examined for prior bioethics cases, such as the RoboRoach, cyborg beetle, ‘microslavery’ of microbes, biohybrid robots incorporating tissues from sea slugs (which are known to possess nociceptors), and other tissue cutting experiments involving soft-bodied invertebrates. However, biohybrid robotic jellyfish pose further ethical questions of potential ecological consequences as ocean monitoring tools, such as the impact of electronic waste in the ocean. To conclude these evaluations, we recommend that publishers require brief ethical statements for invertebrate research, which can include the following: a scientific justification for the research, discussion of the 4Rs, and cost-benefit analysis. We also delineate the need for more research on pain and nociception in invertebrates, which can then be used to revise or validate current research standards. These actions provide a stronger basis for the ethical study of invertebrate species, with implications for individual, species-wide, and ecological impacts on animals, as well as for interdisciplinary studies in science, engineering, and philosophy.

Positioning is an essential aspect of robot navigation, and visual odometry an important technique for continuous updating the internal information about robot position, especially indoors without GPS. Visual odometry is using one or more cameras to find visual clues and estimate robot movements in 3D relatively. Recent progress has been made, especially with fully integrated systems such as the RealSense T265 from Intel, which is the focus of this article. We compare between each other three visual odometry systems and one wheel odometry, on a ground robot. We do so in 8 scenarios, varying the speed, the number of visual features, and with or without humans walking in the field of view. We continuously measure the position error in translation and rotation thanks to a ground truth positioning system. Our result show that all odometry systems are challenged, but in different ways. In average, ORB-SLAM2 has the poorer results, while the RealSense T265 and the Zed Mini have comparable performance. In conclusion, a single odometry system might still not be sufficient, so using multiple instances and sensor fusion approaches are necessary while waiting for additional research and further improved products.

An easier method for the calibration of differential drive robots is presented. Most of the calibration is done on-board and it is not necessary to expend too much time taking note of the robot's position. The calibration method does not need a big free space to perform the tests. The bigger space is just in a straight line, which is easy to find. Results with the proposed method are compared with those from UMB as a reference, and they show very little deviation while the proposed calibration is much simpler.

Present paper is dealing with the adaptive static balancing of robot or other mechatronic arms that are moving in vertical plane and whose static loads are variable, by using counterweights and springs. Some simple passive and approximate solutions are proposed and an example is shown. The active and exact solutions by using adaptive real time control in the case of unknown variation of static loads are simulated on VIPRO platform developed at Institute of Solid Mechanics of Romanian Academy.

Maze navigation using one or more robots has become a recurring challenge in scientific literature and real life practice, with fleets having to find faster and better ways to navigate environments such as a travel hub (e.g. airports) or to evacuate a disaster zone. Many methods have been used to solve this issue, including the implementation of a variety of sensors and other signal receiving systems. Most interestingly, camera-based techniques have increasingly become more popular in this kind of applications, given their robustness and scalability. In this paper, we have implemented an end-to-end strategy to address this scenario, allowing a robot to solve a maze in an autonomous way, by using computer vision and path planning. In addition, this robot shares the generated knowledge to another by means of communication protocols, having to adapt its mechanical characteristics to be able to solve the same challenge. The paper presents experimental validation of the four components of this solution, namely camera calibration, maze mapping, path planning and robot communication. Finally, we present the integration and functionality of these methods applied in a pair of NAO robots.

Cloud robotics is becoming an alternative to support advanced services of robots with low computing power as network technology advances. Recently, fog robotics has gained attention since the approach has merit relieving latency and security issues over the conventional cloud robotics. In this paper, a Function-as-a-Service based Fog Robotic (FaaS-FR) for cognitive robots is proposed. The model distributes the cognitive functions according to the computational power, latency and security with a public robot cloud and fog robot server. During the experiment with a Raspberry Pi as an edge, the proposed FaaS-FR model shows efficient and practical performance in the proper distribution of the computational work of the cognitive system.

Glass cleaning is one of the major cleaning tasks in malls, offices, and modern households where the human workforce is still used for cleaning. Manual cleaning on façade glasses is a less safe, tedious, ineffective, and complex process. With the advancement of robot technology, it is possible to use robots for glass cleaning to facilitate mankind and improve cleaning efficiency. This work presents the development of a vacuum-type glass cleaning robot for façade cleaning and its performance analysis. The developed square-shaped robot is controlled by an Arduino Mega microcontroller, equipped with vacuuming and cleaning technology. An adhesion mechanism on the wheels makes the robot move forward and backward on the glass. The robot runs on a 24-volt DC with a power rating of 75 watts. There are ultrasonic sensors to detect obstacles and help the robot navigate. The robot uses a random-walk mechanism and works continuously for 90 minutes effectively. The performance of the robot has been analyzed in terms of coverage area, repeatability, and dust collection efficiency.

Imitation learning, also known as programming by demonstration, has been shown to be a promising paradigm for intuitive robot programming by non-expert users. However, the classical kinesthetic approach with physical hand guidance suffers from generalizability across different robot types and is impractical for demonstrating tasks with long horizons. Visual imitation learning enables the recording of multi-step tasks as a single continuous video, allowing non-experts to demonstrate tasks naturally. Existing approaches typically require a large amount of data to develop end-to-end deep learning models that map raw pixels to robot actions. This paper explores the application of visual imitation learning from one-shot demonstration, significantly reducing the data requirements and simplifying the programming process. To achieve this target, a framework is proposed to map hand trajectories to the robot end-effector, consisting of four essential components: hand detection; object detection; segmentation of the trajectories into elemental skills; and learning the skills. Methods are developed for each component and evaluated on recorded videos to demonstrate the effectiveness of the proposed framework.

In wheeled vehicles, there exists a challenge concerning the alignment of the front wheels during turns. When both wheels are turned to the same extent, the inner wheel experiences lateral slippage on the road surface, resulting in reduced steering efficiency. Such problems can be solved by using the Ackermann principle. There are two approaches: through the steering mechanism or by employing autonomous wheel control. From a technical standpoint, it is achievable to synthesize a steering mechanism that fulfills the Ackermann condition, ensuring as accurately as possible for any given turning radius. This research paper focuses on synthesizing a steering mechanism, specifically a two-circuit linkage that links the left and right wheels. The structure and kinematics of this mechanism are being investigated. Following the principles of Ackermann, an objective function for the kinematic synthesis of the mechanism has been formulated. The synthesis process of the mechanism is conducted using the analytical method of interpolation in four parameters. A dedicated method has been developed, and kinematic analysis of the mechanism using the synthesized parameters has been performed. The simulation results have demonstrated high accuracy in achieving the desired implementation of the Ackermann condition.

Okra, a widely grown vegetable in many regions, often suffers from freshness loss during transportation, causing significant waste. Factors like variety, environment, maturity, and handling affect its quality. Current methods for checking okra tenderness are slow and prone to mistakes, so we need a better, non-damaging method. This study aims to use a device on a robot arm to assess okra freshness and tenderness. We tested 120 okra pods, storing some in a cold chamber for 24 hours (considered tender) and others at room temperature for two days before moving them to a cold environment for five more days (considered not tender). We used a force sensor on a robot arm to measure okra hardness without damaging it, then did tenderness tests. We found that certain sensor data, like the first slope (S1) and the difference between the maximum value and the first overshoot (Os), were good predictors of tenderness, with an accuracy rate of nearly 80%. We also validated this non-damaging method with weight loss, compression, and puncture tests, achieving a 95.5% accuracy rate in distinguishing between tender and non-tender okra pods.

This study focuses on the design, development, and evaluation of an educational mobile robot, named Robot-T2, to be used in educational activities within a technical school. The primary objective was to create a versatile platform that allows students to explore programming, engineering, and science concepts in a practical and collaborative manner. The methodology included an iterative design and testing approach, incorporating feedback from students and teachers to continuously improve the robot's functionality. The tests covered autonomous navigation, line following, and object manipulation, using the OnBotJava programming software and the Control Hub as the main interface. The results demonstrated that Robot-T2 is highly efficient and adaptable in various educational contexts, showing remarkable precision in navigation and object manipulation. The design iterations significantly improved the robot's performance, enriching the educational experience and promoting active learning. In conclusion, educational robotics, represented by Robot-T2, has great potential to enhance the teaching and learning process in technical schools, fostering teamwork, problem-solving, and the integration of technology in the classroom. This project is expected to inspire future developments in educational robotics.

This conceptual paper explores the potential of integrating Electromagnetic Fields (EMF) with traditional physiological signals to enhance emotional contagion in Human-Robot Interaction (HRI). A focused literature review identifies gaps in current HRI models that rely solely on visual, auditory, and known physiological cues for emotional exchange. A novel framework is proposed, incorporating EMF as a complementary modality, aiming to deepen emotional synchronization between humans and robots. The paper lays groundwork for future research to consider EMF detection as a complementary modality alongside traditional cues. It also addresses technological requirements and discusses potential limitations. By extending the modalities used in emotional contagion, this work seeks to advance the development of more intuitive and empathetic robotic systems.

(1) Background: The social robot interaction design is critical in determining acceptance and user experience. However, few studies have systematically discussed the current focus and future research directions of social robot interaction design from a bibliometric perspective. Therefore, in order to identify the latest research progress and evolution trajectory of research hotspots in social robot interaction design over the last decade. (2) Methods: based on 2416 papers related to social robot interaction design collected in the Web of Science (WOS) database, a comprehensive review was conducted by using bibliometrics to draw a knowledge map using VOSviewer and CiteSpace in an integrated manner. (3) Conclusions: The current research hotspots of social robot interaction design mainly focus on #1the study of human-robot relationships in social robot, #2Research on the Emotional Design of Social Robot, #3research on social robot for children's psychotherapy, #4research on companion robot for elderly rehabilitation, and #5research on educational social robot. The reference co-citation identifies the classic literature that forms the basis of the current research, which provides theoretical guidance and methods for the current research. Finally, we discuss several future research directions and challenges in this field.

Most of the fishing currently practiced in Japan is done by small vessels with a small number of fishermen (one or two). One of the most common fishing methods is longline fishing. However, this method requires the vessel to operate at a constant low speed because the depth of the hook must be kept constant while adjusting the speed of the fishing boat to the tidal current. In addition, because the vessel must maneuver and fish at the same time, automation is desired. Thus, we propose a robotic system that can control the depth of the trap at a constant depth even when the speed of the vessel and the current change, and that can successfully fish without the need for skilled fishermen. Fishing can be conducted regardless of the speed of the vessel, whereas currently it is controlled by the speed of the vessel and the tidal current. Therefore, it may contribute to proposing new fishing methods as well as the existing ones. This can contribute to the shortage of successors to the fishing industry and to the revitalization of the fishing industry.

Factory safety inspections are crucial for ensuring safe production. However, manual inspections present issues such as low efficiency and high workload. Inspection robots provide an efficient and reliable solution for completing patrol tasks. The development of robot localization and path planning technologies provides guarantees for factory inspection robots to autonomously complete inspection tasks in complex environments. This paper studies mapping and localization, as well as path planning methods for robots in order to meet the application requirements of factory inspections. Two SLAM application systems based on multiple-line laser radar and vision are designed for different scenarios in consideration of the limitations of cameras and laser sensors in terms of their own characteristics and applicability in different environments. To address the issue of low efficiency in inspection tasks, a hybrid path planning algorithm that integrates the A-star algorithm and time elasticity band algorithm is proposed. This algorithm effectively solves the problem of path planning in complex environments that is prone to falling into local optimal solutions, thereby improving the inspection efficiency of robots. Experimental tests show that the designed SLAM and path planning methods can meet the needs of robot inspection in complex scenes and have good reliability and stability. The code used in this article is open source and can be accessed at https://github.com/Mxiii99/RSPP_CS.git.

It is difficult to effectively operate a dual-arm robot using only the information written in a cooking recipe. To cope with this problem, this paper proposes a graph based approach on bimanual cooking motion planning from a cooking recipe. In our approach, we first decompose the cooking recipe into graph elements. Then, we try to connect the graph elements taking into account the attributes of the input/output nodes. If two graph elements cannot be connected each other, we search for a graph element that can be inserted between them from the database of graph elements. Since the constructed graph includes the whole sequence of the robot’s motions to perform the cooking task, we can generate a task sequence of a dual-arm manipulator simultaneously performing two different tasks by using two arms. Through experimental study, we show that it is possible to generate robot motions from a cooking recipe and perform the cooking motions while simultaneously moving the left and right arms.

The paper deals with the problems of direct kinematics related to a 2T6R robot, the direct kinematics of the plane mechanism of the robot. The direct kinematics of this proposed new robot help to study the movement, including the dynamic one, to determine the forces in the mechanism and to model the possible trajectories of the final effector point, thus determining the robot's working space and some of its multiple possible uses. Two totally different methods were used to verify the calculation relations, the results obtained by both methods being practically identical. The first method used is an original trigonometric method, and the second is an original geometrically analytical method.

In the design of educational robots, it seems undecided whether robots should show social behaviors and look human-like or that such cues are indifferent to learning. We conducted an experiment with different designs of social robots, rehearsing the multiplication tables with primary school children in Hong Kong. Results show that affective bonding tendencies may occur but did not significantly contribute to the learning progress of these children, perhaps due to the short interaction period. Nonetheless, 5 minutes of robot tutoring improved their scores with about 30% and only for a few challenged children, performance dropped. We discuss that topics such as teaching language skills may be fostered by human likeness in appearance and behaviors but that for STEM-related subjects, the social aspects of robots hardly matter.

This paper describes the development of a laser-based people detection and obstacle avoidance algorithm for a differential-drive robot, which is used for transporting materials along a reference path in hospital domains. Detecting humans from laser data is an important functionality for the safety of navigation in the shared workspace with people. Nevertheless, traditional methods normally utilize machine learning techniques on hand-crafted geometrical features extracted from individual clusters. Moreover, the datasets used to train the models are usually small and need to manually label every laser scan, increasing the difficulty and cost of deploying people detection algorithms in new environments. To tackle these problems, (1) we propose a novel deep learning-based method, which uses the deep neural network in a sliding window fashion to effectively classify every single point of a laser scan. (2) To increase the speed of inference without losing performance, we use a jump distance clustering method to decrease the number of points needed to be evaluated. (3) To reduce the workload of labeling data, we also propose an approach to automatically annotate datasets collected in real scenarios. In general, the proposed approach runs in real-time, performs much better than traditional methods, and can be straightforwardly extended to 3D laser data. Secondly, conventional pure reactive obstacle avoidance algorithms can produce inefficient and oscillatory behaviors in dynamic environments, making pedestrians confused and possibly leading to dangerous reactions. To improve the legibility and naturalness of obstacle avoidance in human crowded environments, we introduce a sampling-based local path planner, similar to the method used in autonomous driving cars. The key idea is to avoid obstacles by switching lanes. We also adopt a simple rule to decrease the number of unnecessary deviations from the reference path. Experiments carried out in real-world environments confirmed the effectiveness of the proposed algorithms.

This work presents the development and implementation of a distributed navigation system based on computer vision. The autonomous system consists of a wheeled mobile robot with an integrated colour camera. The robot navigates through a laboratory scenario where the track and several traffic signals must be detected and recognized by using the images acquired with its on-board camera. The images are sent to a computer server that processes them and calculates the corresponding speeds of the robot using a cascade of trained classifiers. These speeds are sent back to the robot, which acts to carry out the corresponding manoeuvre. The classifier cascade should be trained before experimentation with two sets of positive and negative images. The number of images in these sets should be considered to limit the training stage time and avoid overtraining the system.

Aim: To develop an index for quantitative assessment of the upper limb motor function in children with cerebral palsy before and after robot-assisted therapy. Method: An upper limb motor function index was developed using kinematic, surface electromyography and three-axis inertial measurements unit data collected from 15 children with cerebral palsy (CP) and 15 typically developed children. Children with CP underwent 18 robot-assisted therapy sessions with the REAplan device. All children were evaluated, using kinematic data from the REAplan, electromyography and three-axis inertial measurements unit readings from its accelerometer. A principal component analysis was conducted to produce an evaluation index, which is able to detect the deviation from the upper limb motor function of typically developing children group. Children with CP were evaluated twice before and after the intervention with Box and Blocks test and Finger-To-Nose test. The discriminative and concurrent validity of the upper limb motor function index were investigated. Results: The upper limb motor function index was higher in children with CP post therapy (p<0.001). Finger-To-Nose test values improved after robot-assisted therapy (p<0.03). A weak but positive correlation was observed between upper limb motor function index and clinical tests (r=0.012, p=0.95 and r=0.13, p= 0.54 for Box and Blocks test and Finger-To-Nose test respectively). Interpretation: The upper limb motor function index successfully differentiated between the typically developing children and children with CP and was effective in assessing the improvement of the upper limb motor function after robot-assisted therapy. The upper limb motor function index could be extended to assess and monitor rehabilitation therapies of other populations, such as those with stroke and Parkinson’s disease.

The increasing number of robots around us will soon create a demand for connecting these robots in order to achieve goal-driven teamwork in heterogeneous multi-robot systems. In this paper, we focus on robot teamwork specifically in dynamic environments. While the conceptual modeling of multi-agent teamwork has been studied extensively during the last two decades, related engineering concerns have not received the same degree of attention. Therefore, this paper makes two contributions. The analysis part discusses general design challenges that apply to robot teamwork in dynamic application domains. The constructive part presents a review of existing engineering approaches for challenges that arise with dynamically changing runtime conditions. An exhaustive survey of robot teamwork aspects would be beyond the scope of this paper. Instead, we aim at creating awareness for the manifold dimensions of the design space and highlight state-of-the-art technical solutions for dynamically adaptive teamwork, thus pointing at open research questions that need to be tackled in future work.

Introduction: This review explores the literature and presents institutional cases of concurrent robotic multisite surgery—in particular, robot-assisted radical prostatectomy (RARP) and robot-assisted partial nephrectomy (RAPN) for synchronous prostate and kidney cancers. We highlight dual-console synchronous robotic procedures, emphasizing the unique docking tech-nique developed. Aim: The aims of the study were to evaluate the feasibility, safety, and clinical outcomes of concurrent RARP and RAPN for synchronous prostate cancer and small renal tumors, as well as other concurrent robotic multisite surgeries, and to compare institutional findings with the existing literature. Materials and Methods: We describe the unique docking technique used in our procedures, which facilitates atraumatic transitions between surgeries using the same port sites. Additionally, eligible studies on concurrent robotic multisite surgery that were published in English were retrieved from the MEDLINE, Embase, and Cochrane Library databases. Data on operative time, blood loss, complications, and postoperative outcomes were extracted. Results: Eight cases from our institution demonstrated the feasibility and safety of the proposed approach, which is consistent with previous reports. The unique docking technique and dual-console setup enhance surgical precision, offering significant benefits in patient outcomes. As part of the litera-ture review, nine retrospective studies involving 40 cases of concurrent RARP and RAPN were reviewed. Additionally, eleven retrospective studies involving 392 cases of concomitant RARP and robotic transabdominal preperitoneal inguinal hernia repair (RTAPPIHR) were analyzed. Conclusions: Concurrent RARP and RAPN for synchronous prostate and kidney tumors is a viable and effective approach. Our early experience suggests that this and other combined procedures can optimize patient care and reduce costs. Prospective trials are needed to validate these findings and further refine the techniques.

Control of autonomous robot motion in radial mass density field is presented. In that sense the robot motion is described as the function of the radial mass density parameters. The radial mass density field is between the maximal radial mass density and the minimal radial mass density. Between these two limited values one can use n points (n = 1, 2, . . . nmax) and calculate the related radial mass density for each point. The radial mass density is maximal at the minimal gravitational radius and minimal at the maximal gravitational radius. This conclusion is valid for Planck scale, but also for the scales that are less or higher of that one. Using the ratio of the Planck mass and Planck radius it is generated energy conservation constant with value κ = 0.99993392118. Further, in this theory it is possible to connect Planck’s and gravitational parameters as functions of the maximal (or minimal) radial mass density. In that sense the autonomous robot motion in radial mass density field is important for the control of the robot motion at micro and nano scales.

Robotic systems are increasingly being used in healthcare to improve patient care and support healthcare professionals. These robots are especially effective at performing repetitive tasks. In complex cancer cases, robots can enhance surgical precision and efficiency, resulting in reduced pain for patients and a lower risk of complications. Robot-assisted surgery offers high-quality 3D imaging, improved clarity, and increased efficiency. This review paper examines the application of Artificial Intelligence (AI) and robotic systems in the healthcare domain, specifically focusing on the interaction among operators, patients, and robots. The goal is to promote collaboration and improve healthcare provision through human-robot interaction. We considered already published articles by relevance, to identify the primary safety issues that need addressing for the integration of AI and robots in hospitals. Concluding with insights into understanding the focal points of social errors in Human-Robot Interaction (HRI) is crucial for mitigating these errors. While current technologies have reached a certain level of maturity, there are still numerous challenges in utilizing robot-assisted clinical practice, including technological, safety, clinical, financial, insurance, psychological, social, ethical, and legal issues. In addition, there is an urgent issue that needs to be addressed: the alignment of values in artificial intelligence, ensuring that AI systems reflect ethical principles and human values is crucial to avoid negative consequences such as bias, discrimination, and prejudicial decisions. Resolving this complex issue requires collaboration among clinical staff, researchers, programmers, and political decision-makers from various fields.

To encourage proper waste management from electrical and electronic devices (e-waste), it is necessary to invest heavily in the development of recycling technologies. One way to improve the process is to automate separating the shredded parts of e-waste using a robot. This paper's literature review, utilizing the Preferred Reporting Items for Systematic reviews and Meta-Analyses (PRISMA) framework, showcases potential robotic technologies for e-waste separation. However, the intricate design of these devices can pose significant challenges in their implementation. Various legal, organizational, and sociological obstacles have left Serbia's e-waste management practice underdeveloped, resulting in an unsatisfactory recycling rate. In this paper we examined the possibility of using robots on the precise example of recycling refrigerators in a recycling center in Eastern Serbia, concluding that such a solution would have multiple positive effects, both on the employees and the working environment, on the operations of the recycling center itself, and on increasing the e-waste recycling rate in the country.

In order to improve the stiffness of the flexible robot,this paper proposes a variable-stiffness elastic actuator to improve the rigidity of flexible robots. The actuator integrates the working principles of a pneumatic drive, wedge structure, and particle blockage. the tensile stiffness of the actuator is nonlinearly negatively correlated with the air pressure because of the structural and material properties.The compressive stiffness and lateral stiffness increases nonlinearly as air pressure increases, being 3and 121 times greater at 0.17 MPa compared to 0 MPa, respectively. Beyond 0.17 MPa, the two stiffness of the actuator experiences incremental growth due to wedge impedance forces.

Autonomous navigation of a mobile robot in dynamic environments presents a significant challenge in the field of robotics. The primary objective for mobile robot navigation is to ensure both smoothness and safety of movement. A path planning is applied to generate a trajectory that allows the robot to move smoothly while avoiding collisions with both stationary and moving obstacles. This study aims to introduce an Adaptive Neuro-Fuzzy Inference System (ANFIS)-based control strategy for a mobile robot navigating in dynamic environments, with a significant focus on ensuring collision-free path planning. The developed control strategy incorporates four ANFIS controllers, each regulating the robot's responsive behaviors. The experimental scene includes a mobile robot moving in an environment with static and dynamic obstacles without colliding with the obstacles. The experimental tests confirm the model's capability to facilitate collision-free motion, employing a path planning algorithm for determining the shortest route to the target destination. Simulations are conducted to show the effectiveness of the proposed algorithm, highlighting the mobile robot's efficiency in navigating without collisions while avoiding both stationary and moving obstacles using the integration of ultrasonic sensors.

The growing prevalence of social robots in various fields necessitates a deeper understanding of touch in Human-Robot Interaction (HRI). This study investigates how human-initiated touch influences physiological responses during interactions with robots, considering factors such as anthropomorphic framing of robot body parts and attributed gender. Two types of anthropomorphic framings are applied: the use of anatomical body part names and assignment of male or female gender to the robot. Higher physiological arousal is observed when touching less accessible body parts than when touching more accessible body parts in both conditions. Results also indicate that using anatomical names intensifies arousal compared to the control condition. Additionally, touching the male robot resulted in higher arousal in all participants, especially when anatomical body part names were used. This study contributes to the understanding of how anthropomorphic framing and gender impact physiological arousal in touch interactions with social robots, offering valuable insights for social robotics development.

It is known that people perceive animacy in objects. However, many studies on animacy and emotional expressions are limited in that the investigated motions were created by experimenters themselves. This makes the objective validity unclear. Moreover, it remains unclear what types of movements can express emotions with animacy due to the limited number of investigations examining both animacy and emotional expressions. Therefore, we investigated the motion elements for both animacy perception and emotional expressions using simple objects that lack features of specific living things, such as eyes, ears, tails, and voices in this study. First, we investigated the motion elements for animacy perception and emotional expressions using a robot simulator that enabled participants to create undulatory motions by tuning parameters for speed, height, and randomness. In total, 64 participants created motions in Normal (neutral), Joy, Sad, Relaxed, and Angry conditions. The results showed that the medians of speed and height in Normal, related only to animacy, were 0.5569[Hz] and 3.050cm at the edges/4.575cm at the center. The differences in Joy were 0.4028[Hz] and 3.348cm/5.022cm, in Sad were −0.1652[Hz] and −0.9982cm/−1.497cm, in Relaxed were −0.1979[Hz] and −0.4902cm/−0.7353cm, and in Angry were 0.5212[Hz] and 4.688cm/7.032cm. Second, we investigated whether the motion elements revealed in the first experiment were sufficient to express emotions with animacy, using a robot simulator that reflected the results of the motion element investigation. In total, 44 online participants observed the simulator. The results showed that participants could understand emotional arousal levels at the same time as animacy, but they did not fully understand emotional valence. Our findings provide design guidelines for robots that exhibit emotional expressions and closely interact with humans.

Artificial Intelligence (AI) is used in our day-to-day life. AI for journalism is a reality. Just like other vital aspects of our life, AI has also entered the world of journalism. Many reputed news organizations have adopted AI in journalism to perform various newsroom tasks. In today’s digital world, several technologies are powering journalism. One such technology that is transforming the journalism field is artificial intelligence. Accuracy is a core value of journalism. With AI and machine learning systems, there’s a statistical element of uncertainty which means it’s impossible to guarantee 100 percent accuracy. AI tools such as OpenAI’s ChatGPT, Microsoft’s Bing chatbot, and Google’s Bard have been subject to debate now. AI tools have the potential to assist in a variety of tasks, such as scraping PDF files, writing code, and translating languages. AI can be a helpful tool for journalism students and media researchers. A main concern among computational journalists is that AI sometimes hallucinates data. This review paper highlights how artificial intelligence can help journalists.

In the field of vision-based robot grasping, effectively leveraging RGB and depth information to accurately determine the position and pose of a target is a critical issue. To address this challenge, we propose a tri-stream cross-modal fusion architecture for 2-DoF visual grasp detection. This architecture facilitates the interaction of RGB and depth bilateral information and is designed to efficiently aggregate multiscale information. Our novel modal interaction module (MIM) with spatial-wise cross-attention algorithm adaptively captures cross-modal feature information. Meanwhile, the channel interaction modules (CIM) further enhance the aggregation of different modal streams. In addition, we efficiently aggregate global multiscale information through a hierarchical structure with skipping connections. To evaluate the performance of our proposed method, we conduct validation experiments on standard public datasets and real robot grasping experiments. We achieve the image-wise detection accuracy of 99.4% and 96.7% on Cornell and Jacquard datasets respectively. The object-wise detection accuracy reaches 97.8% and 94.6% on the same datasets. Furthermore, physical experiments using the 6-DoF Elite robot demonstrate a success rate of 94.5%. These experiments highlight the superior accuracy of our proposed method.

The soft robot has many degrees of freedom, strong environmental adaptability and good human-computer interaction ability. As the end-effector of the soft robot, the soft gripper can grasp objects of different shapes without destructivity. Based on the theoretical analysis of the soft robot, the kinematics model of the flexible gripper and the theoretical model of the bending deformation of the air cavity were established. Accordingly, the relationship between the bending angle of the soft gripper and the air pressure was determined. Through the application of finite element software, the bending degree of pneumatic network multi-cavity soft gripper was simulated by finite element software, and the influence of structural parameters of soft actuator on bending deformation was determined. In addition, with the 3D technology conducting the printing of soft gripper fixtures and molds, the injection molding the actuator and the human-computer interaction interface controlling the movement of the gripper, the adaptability of the soft gripper in grasping object was verified. The result shows that the software gripper possesses good flexibility and can better grasp objects of different shapes.

Robots for communication are developed extensively with emphasis on sympathy. This study deals with the growth of character and the control of its operation accordingly. The child has time to be alone with the nature of his/her robot friend. The child can interact with other people's emotional expressions through a robot. Step by step, the robot character will grow as the child grows. Through design studies, qualitative processes such as {customer experience audit, eye tracking, mental model diagrams, semantic differences} have been executed for the results. The participatory behavior research approach through user travel is mapped from the user's lead to the evidence-based design. This research considers how the synthetic characteristics can be applied to the physical growth of robot toys through the product design process. With the development of robot toy "Buddy", we tried making two variations on the robot to achieve recognizable growth. (1) A one-dimensional height scaling and (2) facial expression including the distance between two eyes on the screen. Observations represented children's reactions when "Buddy" was released to with the children. As an independent synthetic character, the robot was recognized by children who had the designed function. Robots for training may require more experimentation.

We report on an exploratory study conducted at a graduate school in Sweden with a humanoid robot, Baxter. First, we describe a list of potentially useful capabilities for a robot teaching assistant derived from brainstorming and interviews with faculty members, teachers, and students. These selected capabilities consist of reading, greeting, alerting, remote operation, clarification, and motion. Second, we present feedback on how the robot's capabilities, demonstrated in part with the Wizard of Oz approach, were perceived, and iteratively adapted over the course of several lectures, using the \EP tool. Third, we discuss observations and findings regarding the capabilities and the development process. Our findings suggest that using a social robot as a teaching assistant is promising using the chosen capabilities. We find that personalizing the capabilities and the role of embodiment are important topics to be considered in future work.