Layered 2D graphene oxide (GO) films are integrated with silicon nitride (SiN) waveguides to experimentally demonstrate an enhanced Kerr nonlinearity via four-wave mixing (FWM). Owing to the strong light–matter interaction between the SiN waveguides and the highly nonlinear GO films, the FWM performance of the hybrid waveguides is significantly improved. SiN waveguides with both uniformly coated and patterned GO films are fabricated based on a transfer-free, layer-by-layer GO coating method together with standard photolithography and lift-off processes, yielding precise control of the film thickness, placement and coating length. Detailed FWM measurements are carried out for the fabricated devices with different numbers of GO layers and at different pump powers. By optimizing the trade-off between the nonlinearity and loss, we obtain a significant improvement in the FWM conversion efficiency of ≈7.3 dB for a uniformly coated device with 1 layer of GO and ≈9.1 dB for a patterned device with 5 layers of GO. We also obtain a significant increase in FWM bandwidth for the patterned devices. A detailed analysis of the influence of pattern length and position on the FWM performance is performed. Based on the FWM measurements, the dependence of GO’s third-order nonlinearity on layer number and pump power is also extracted, revealing interesting physical insights about the 2D layered GO films. Finally, we obtain an enhancement in the effective nonlinear parameter of the hybrid waveguides by over a factor of 100. These results verify the enhanced nonlinear optical performance of SiN waveguides achievable by incorporating 2D layered GO films.

The principles of causality and unitarity are studied within rational nonlinear electrodynamics proposed earlier. We investigate dyonic and magnetized black holes and show that in the self-dual case, when the electric charge equals the magnetic charge, corrections to Coulomb's law and Reissner-Nordstrom solutions are absent. In the case of the magnetic black hole, the Hawking temperature, the heat capacity and the Helmholtz free energy are calculated. It is shown that there are second-order phase transitions and it was demonstrated that at some range of parameters the black holes are stable.

Statistical mechanics investigates how emergent properties of macroscopic systems (such as temperature and pressure) relate to microscopic state fluctuations. The underlying idea is that global statistical descriptors of order and variability can monitor the relevant dynamics of the whole system at hand. Here we test the possibility of extending such an approach to psychotherapy research investigating the possibility of predicting the outcome of psychotherapy on the sole basis of coarse-grained empirical macro-parameters. Four good-outcome and four poor-outcome brief psychotherapies were recorded, and their transcripts coded in terms of standard psychological categories (abstract, positive emotional and negative emotional language pertaining to patient and therapist). Each patient-therapist interaction is considered as a discrete multivariate time series made of subsequent word-blocks of 150-word length, defined in terms of the above categories. Static analysis (Principal Component Analysis) highlighted a substantial difference between good-outcome and poor-outcome cases in terms of mutual correlations among those descriptors. In the former, the patient’s use of abstract language correlated with therapist’s emotional negative language, while in the latter it co-varied with therapist’s emotional positive language, thus showing the different judgment of the therapists regarding the same variable (abstract language) in poor and good outcome cases. On the other hand, the dynamic analysis, based on five coarse-grained descriptors related to variability, degree of order and complexity of the series, demonstrated a relevant case-specific effect, pointing to the possibility of deriving a consistent picture of any single psychotherapeutic process. Overall, the results showed that the systemic approach to psychotherapy (an old tenet of psychology) is mature to shift from a metaphorical to a fully quantitative status.

This paper is intended at highlighting the main mechanical parameters controlling the behavior of the so-called "acceleration-sensitive" Non-Structural Components (NSCs). In the first part a short review of the current state of knowledge and the critical issues related to the prediction of the seismic response of NSCs is reported. Then, the paper presents the results of a numerical parametric analysis intended to capture the key features of the dynamic response of a two-degree-of-freedom (2DOF) system which is supposed to be representative of both the main structure and the "non-structural" component (NSC). Particularly, it allows to simulate the coupled behaviour of both main structure and NSC and evaluating their response. The main parameters controlling the dynamic response of NSCs emerge from this study, which could pave the way towards formulating more mechanically consistent relationships for evaluating the maximum accelerations induced by seismic shakings on NSCs.

In this article, we consider the three dimensional $\alpha$-fractional nonlinear delay differential system of the form \begin{align*} D^{\alpha}\left(u(t)\right)&=p(t)g\left(v(\sigma(t))\right),\\D^{\alpha}\left(v(t)\right)&=-q(t)h\left(w(t))\right),\\D^{\alpha}\left(w(t)\right)&=r(t)f\left(u(\tau(t))\right),~ t \geq t_0, \end{align*} where $0 < \alpha \leq 1$, $D^{\alpha}$ denotes the Katugampola fractional derivative of order $\alpha$. We have established some new oscillation criteria of solutions of differential system by using generalized Riccati transformation and inequality technique. The obtained results are illustrated with suitable examples.

In this work, a mixture of Elzaki transform and projected differential transform method is applied to solve a nonlinear wave-like equations with variable coefficients. Nonlinear terms can be easily manipulated by using the projected differential transformation method. The method gives the results show that the proposed method is very efficient, simple and can be applied to other applications.

This article, we study the sufficient conditions for the controllability of second-order impulsive partial neutral evolution differential systems with infinite delay in Banach spaces by using the theory of cosine families of bounded linear operators and fixed point theorem.

This paper focuses on the problem of finite-time stabilization of homogeneous, non-Lipschitz systems with dilations. A key contribution of this paper is the design of a virtual recursive Hölder, non-Lipschitz state feedback which renders the non-Lipschitz systems in the special case dominated by a lower-triangular nonlinear system, finite-time stable. The proof is based on a recursive design algorithm developed recently, to construct the virtual Hölder continuous, finite-time stabilizer as well as a C¹ positive definite and proper Lyapunov function that guarantees finite-time stability of the non-Lipschitz non-linear systems.

Incremental control strategies provide undeniable advantages for controlling Uncrewed Aerial Vehicles (UAVs) due to their reduced model dependency and accurate tracking capacities. This is of particular relevance for hybrid UAVs, specially for tail-sitters, which perform complex manoeuvres when transitioning to and from aerodynamic flight. This paper summarizes the research undertaken in the application of the Incremental Nonlinear Dynamics Inversion (INDI) and Incremental Backstepping (IBKS) to a small tail-sitter UAV. After the application of these control strategies in a simulated scenario, the implementation in a Micro-Controller Unit was validated in a Hardware-in-the-Loop scenario. Following such validation, indoor experimental trials were undertaken in order to evaluate the capacity of these controllers to stabilize and control the real aircraft. The stabilization in the flight trials was successfully implemented and allow to conclude that both INDI and IBKS are control strategies suited to control a tail-sitter in vertical flight, providing accurate tracking capabilities under smooth actuation. Furthermore, it was found that the IBKS is significantly more computationally demanding than the INDI, although having a global proof of stability that is of interest in aircraft control.

Abstract. This paper proposes a Second Order Terminal Sliding Mode (2TSM) approach to the trajectory tracking of Differential Drive Mobile Robot (DDMR). Within this cascaded control scheme, the 2TSM dynamic controller, at the inner most loop, tracks the robot’s velocity quantities; while a kinematic controller, at the outer most loop, regulates the robot’s positions. In this manner, chattering is greatly attenuated and finite time convergence is guaranteed by the second order TSM manifold which involves higher order derivatives of the state variables, resulting in inherently robust as well as fast and better tracking precision. The simulation results demonstrate the merit of the proposed control methods.

This study presents the complexity and sensitivity of chaotic system dynamics in the case of the double pendulum. It applied detailed numerical analyses of the double pendulum in multiple computing platforms in order to demonstrate the complexity in behavior of the system of double pendulums. The equations of motion were derived from the Euler-Lagrange formalism, in order to capture the system's dynamics, which is coupled nonlinearly. These were solved numerically using the efficient Runge-Kutta-Fehlberg method, implemented in Python, R, GNU Octave, and Julia, while runtimes and memory usage were extensively benchmarked across these environments. Time series analyses, including the calculation of Shannon entropy and the Kolmogorov-Smirnov test, quantified the system's unpredictability and sensitivity to infinitesimal perturbations of the initial conditions. Phase space diagrams illustrated the intricate trajectories and strange attractors, as further confirmation of the chaotic nature of the double pendulum. All the findings have a clear indication of the importance of accurate measurements of the initial condition in a chaotic system, contributing to an increased understanding of nonlinear dynamics. Future research directions are faster simulations using Numba and GPU computing, stochastic effects, chaotic synchronization, and applications in climate modeling. This work will be useful for understanding chaos theory and efficient computational approaches in complex systems of dynamical nature.

This paper proposed an optimal tracking control scheme through adaptive dynamic programming(ADP) for a class of partially unknown discrete-time nonlinear systems based on radial basis function neural network(RBF-NN). In order to acquire the unknown system dynamics, we use two RBF-NNs, the one is used to construct the identifier, and the another is used to directly approximate the steady-state control input, where a novel adaptive law is proposed to update neural network weights. While the optimal feedback control and the cost function are derived via feedforward neural networks approximating, it is proposed to regulate the tracking error, the critic network and the actor network are then trained online to obtain the solution of the associated Hamilton–Jacobi–Bellman (HJB) equation being built under the ADP framework. Simulations verify the effectiveness of the optimal tracking control technique using the neural networks.

The traditional receiver employs scalar tracking loops, resulting in degraded navigation performance in weak signal and high dynamic scenarios. An innovative design of a vector tracking receiver based on nonlinear Kalman filter (KF) tracking loops is proposed in this paper, which combines the strengths of both vector tracking and KF tracking loops. Firstly, a comprehensive description of the vector tracking receiver model is presented, and unscented Kalman filter (UKF) is applied to nonlinear tracking loop. Secondly, to enhance the stability and robustness of the KF tracking loop, we introduce square root filtering and an adaptive mechanism. The tracking loop based on square root UKF (SRUKF) can dynamically adjust its filtering parameters based on signal noise and feedback Doppler error. Finally, the proposed method is implemented on a software-defined receiver (SDR), and the field vehicle experiment demonstrates the superiority of this method over other receivers in complex dynamic environments.

Stratified Taylor Couette Flow (STCF) undergoes transient growth. Recent studies have shown that there exists transient amplification in the linear regime of counter-rotating STCF. It is reported that as Gr increases, the maximum amplification factor ($G_0$) initially decays before it eventually starts growing after reaching a certain critical value Gr$_{c}$. Assuming other parameters of the model are kept constant, the value Gr$_{c}$ changes with respect to different speed ratios of the cylinders. The observed decay/growth pattern of $G_0$ is attributed to the interplay between the induced shear and buoyancy. In this study, the mechanism that triggers this observed pattern is investigated. The kinetic budget of the optimal transient perturbation is analysed numerically to simulate the interaction of the shear production (SP), buoyancy production (BP) and other energy components that contributes to the total optimal transient kinetic energy. These contributions affect the total energy by influencing the perturbation to extract kinetic energy (KE) from the mean flow. The decay of $G_0$ resulted from the positive amplification of both BP and SP, while the growth is attributed to the negative and positive amplification of BP and SP, respectively. The optimal SP is positively amplified, implying that there is the possibility of constant linear growth. These findings agree with the linear growth rate for increasing values of Gr.

Doubly-fed induction generators (DFIG) find extensive application in variable-speed wind power plants, providing notable advantages such as cost-effectiveness, operational flexibility across varying speeds, and enhanced power quality. This research focuses on the control of DFIGs employed in variable-speed wind turbine configurations. A suitable mathematical model is chosen for representative systems following a comprehensive review of contemporary research. Subsequent analysis reveals the instability of the open-loop time response of the system. To address this instability, the initial approach involves the implementation of the conventional Model Predictive Controller (MPC). However, the outcomes indicate that this controller falls short of delivering satisfactory performance despite the enhanced stability. In the subsequent phase, efforts are made to mitigate the impact of wind input variability by utilizing the Kalman filter, given its effectiveness in handling high variability. Following this, a novel methodology is introduced, which combines nonlinear MPC with the Lyapunov function. This method is based on the nonlinear model of the system. By using the Lyapunov function in the nonlinear MPC structure, the stability of the designed controller is guaranteed. The simulation results conducted using MATLAB software show that the output variables of the modeled DFIG system achieve stability within a reasonable timeframe applying the input.

Practically important properties of real liquids, including seawater, are their nonlinear properties, which include a nonlinear acoustic parameter, as well as cavitation strength – a rupture of the continuity of a liquid at high intensities in an acoustic wave. The manifestation of nonlinear effects is greatly facilitated by the presence of various nuclei in the liquid – gas bubbles, foreign particles, and other inclusions of various origins. For practical applications, it is important to study the properties of real liquids with inclusions in them. Due to the difficulties of measuring cavitation strength by acoustic methods, other methods are being sought. It is proposed to use an optoacoustic method associated with the use of laser radiation that causes optical breakdown - optical cavitation, that accompanied by a strong sound generation effect. The connection between optical breakdown thresholds and acoustic cavitation thresholds has been established, which can later be used to identify cavitation thresholds at high static pressures (at great depths in the sea), where the use of acoustic emitters is extremely difficult. The paper studies the bubble size distribution function in seawater, combined with studies of the acoustic nonlinearity parameter and cavitation strength at various depths. The interrelation of these characteristics for seawater is shown.

This study presents an innovative approach named Optimal Adaptive Continuous Barrier Function Terminal Sliding Mode Control (OACBF-TSMC) approach with a novel switching manifold, to control mathematical model of nonlinear systems under model uncertainties and external disturbances. The proposed OACBF-TSMC approach combines the advantages of adaptive control, continuous barrier functions, and terminal sliding mode control to achieve robust stability of the mathematical model of nonlinear systems, and by using a genetic algorithm that tries to optimize the controller parameters as much as possible so that the proposed controller is the most to have efficiency and performance. The proposed method is designed to address the challenges of systems and provide superior performance in terms of stabilization accuracy, disturbance rejection, and robustness against uncertainties. However, the critical challenge facing the proposed controller is the complete elimination of the chattering phenomenon, which is the most important problem of ordinary sliding mode controllers. The simulation results show that the system trajectories in the proposed approach have converged to the origin with minimal overshoot and under-shoot in a finite time; In addition, the chattering problem in the control inputs has been well eliminated, which makes the proposed method suitable for various systems, including chaotic systems, energy sources, and distributed production systems. Furthermore, the OACBF-TSMC approach has the potential to enhance the stability and reliability of control systems, contributing to the integration of the system states.

In this paper, to make the missile intercept the maneuvering target, the parallel approaching guidance law is developed. In order to estimate the target maneuver more accurately and reduce that’s influence on guidance accuracy, the distance-scalar disturbance observer is employed. Specifically, the estimation accuracy of the observer designed is regardless of the relative distance. The finite-time prescribed performance is employed to ensure that the line-of-sight angular rate is capable of converging to a predesigned small region in the specified finite time. All signals of interception system can guarantee ultimately uniformly boundedness proved by the Lyapunov stability theory. Finally, the availability of the parallel approaching guidance law is demonstrated by the numerical simulation.

The motion of Unmanned Surface Vehicles (USVs) is frequently disturbed by the ocean wind, wave and current. A poorly designed controller will lead to failures and even safety problems during actual navigation. In order to obtain satisfied control performance of the motion for the USVs, a Model Predictive Control (MPC) based on improved Nonlinear Disturbance Observer (NDO) is proposed. Firstly, the USV model is approximately linearized and MPC is designed for the multivariable system with constraints. In order to compensate the influence of disturbances, an improved NDO is designed, with which the calculation time for the MPC saved a lot. Finally, comparison experiments are conducted between the MPC with NDO and the MPC with improved NDO, and the results show that they have similar performance to the USVs. However, the proposed method has less parameter to be tuned and it is much more time-saving compared to the MPC with traditional NDO.

As an option to deal with the insulin-dependent disease, a recent commuted PD control strategy is designed and carefully analyzed for different clinic diabetic patients. This controller approach is mainly conceived to stabilize the glucose blood concentration in a diabetic patient around its basal value, hence avoiding extreme situations such as hypoglycemia and hyperglycemia. This control strategy receives two inputs carefully tuned to actuate when the measured variable is out of a prescribed healthy zone. Therefore, one of these variables is invoked to decrease the glucose concentration to insulin injection, and the other is employed to increase the glucose absorption, both by using a proper PD controller. According to our numerical experiments, our controller approach performs well, even when there is an external disturbance in the controlled system.

A nonlinear MEMS multimass sensor is investigated. The MEMS design consists of an array of nonlinear microcantilevers clamped to a shuttle mass which, in turn, is attached to a linear spring and a dashpot. The microcantilevers are made of a polymeric hosting matrix reinforced by aligned carbon nanotubes (CNT) with different CNT volume fractions in each cantilever so as to suitably tune the frequency bandwidth of the device. The advantages of a single input-single output (SISO) system are here exploited for the design, actuation and detection principles as in previous literature.

Winter frost injury is a major limiting factor for olive cultivation in temperate regions. The response of olive shoots to freezing stress can be used for selecting resistant genotypes to freezing. The electrolyte leakage (EL) and tetrazolium tests (TZ) are commonly used to evaluate dead tissues in cold stress studies. The temperature-response curve of dead tissues to lethal temperature (LT) is measured with models to calculate LT50 and LT90. In this study, we evaluated the accuracy and efficiency of eighteen non-linear regression models (NLRs) in calculating LT50 and LT90 of freezing stress in different olive cultivars at various stages of dormancy. After evaluating the prediction performance of NLR models, it was found that only eight models were suitable for the purpose of this research out of the 18 models examined. The 2p-logistic and Gompertz models were selected for modeling EL and TZ, respectively. Our research findings indicate that the Roughani, Kawi, and Zard varieties of olive trees exhibit the best performance in cold weather conditions. Our findings provide valuable insights into selecting frost-resistant cultivars and designing effective strategies for cold acclimation in olive cultivation.

Non-standard Lagrangians do not display any discernible energy-like terms, yet they give the same equations of motion as standard Lagrangians, which have easily identifiable energy-like terms. A new method to derive non-standard Lagrangians for second-order nonlinear differential equations with damping is developed and the limitations of this method are explored. It is shown that the limitations do not exist only for those nonlinear dynamical systems that can be converted into linear ones. The obtained results are applied to selected population dynamics models for which non-standard Lagrangians and their corresponding null Lagrangians and gauge functions are derived, and their roles in the population dynamics are discussed.

With correct dynamic system parameters (embodied in self-awareness statements), a controller can provide precise signals for tracking desired state trajectories. If dynamic system parameters are initially guessed incorrectly, a learning method may be used to find the correct parameters. In the deterministic artificial intelligence method, self-awareness statements are formed as mathematical expressions of the governing physics. When the nonlinear, coupled expressions are precisely parameterized as the product of known matrix components and unknown victrix (i.e., a regression form) tracking errors may be projected onto the known matrix to update the unknown victrix in an optimal form (in a two-norm sense). In this work, a modified learning method is proposed and proved to have global convergence of both state error and parameter estimation error. The modified learning method is compared with those in the prequels using simulation experiments of three-dimensional rigid body dynamic rotation motion. The modified approach is two magnitudes better than the methods in the prequels in terms of state error convergence.

As a derivative of graphene, graphene oxide (GO) was initially developed by chemists to emulate some of the key properties of graphene, but it was soon recognized as a unique material in its own right, addressing an application space that is not accessible to chemical vapor deposition based materials. Over the past decade, GO has emerged as a new frontier material with tremendous advances in its material fabrication and quality control over its properties. These in turn have led to rapid progress in GO based photonics, electronics, and optoelectronics concepts and devices, evoking new science and paving the way for many technological breakthroughs with exceptional performance. Here, we review the unique fundamental characteristics of GO, its thin film fabrication methods, patterning techniques, and mechanisms for tuning its material properties. This latter capability in particular has enabled novel advanced functional photonic, electronic, and optoelectronic devices. Understanding these insights is essential for designing and tailoring GO properties for state-of-the-art applications including solar energy harvesting, energy storage, medical diagnosis, image displays, and optical communications. We conclude by discussing the open challenges and exciting opportunities of this field, together with future prospects for major technological advancements and breakthroughs.

Thermodynamics and phase transitions of magnetic Anti-de Sitter black holes are studied. We consider an extended phase space thermodynamics with the cosmological constant being a thermodynamic pressure and the black hole mass is treated as a chemical enthalpy. The extended phase space thermodynamics of black holes mimics the behavior of the Van der Walls liquid. Quantities conjugated to the coupling of nonlinear electrodynamics (NED) and a magnetic charge are obtained. Thermodynamic critical points of phase transitions are investigated. It is demonstrated that the first law of black hole thermodynamics and the generalized Smarr relation take place. The Joule--Thomson adiabatic expansion of NED-AdS black holes is studied. The dependence of inversion temperature on pressure and the minimum of inversion temperature are found.

Cellular Nonlinear Networks (CNN) are a concept introduced in 1988 by Leon Chua and Lin Yang as a bio-inspired architecture, capable of massively parallel computation. Later on, CNN have been enhanced by incorporating designs that incorporate memristors to profit from their processing and memory capabilities. In addition, Stochastic Computing (SC) can be used to optimize the quantity of required processing elements; thus it provides a lightweight approximate computing framework, quite accurate and effective, though. In this work, we propose utilization of SC in designing and implementing a memristor-based CNN. As a proof of the proposed concept, an example of application is presented. This application combines Matlab and a FPGA in order to create the CNN. The implemented CNN has then been used to perform three different real-time applications on a 512x512 gray-scale and a 768x512 color image: storage of the image, edge detection, and image sharpening. It has to be pointed out that the same CNN has been used for the three different tasks, with the sole change of some programmable parameters. Results show an excellent capability with significant accompanying advantages, like the low number of needed elements further allowing for a low cost FPGA-based system implementation, something confirming the system’s ability for real time operation.

Neural networks models are mostly represented by oriented graphs where only the components, constitutive elements of the graph, are transcribed into mathematical xpression. Indeed, accurate knowledge of the full expression of the model is required in certain situations such as selecting among several reference models, the one that best fits the available data or comparing the explanatory and predictive performance of an established model with respect to some reference models. In this paper, we establish a formalism of the mathematical expression for multilayer perceptron neural network in a general framework, MLP-p-n-q, with p, n and q natural integers and show its restriction to cases where one has a hidden layer and multivariate outputs (MLP-p-1-q), and then a single output (MLP-p-1-1). Then, we give some specific cases of the most commonly used models. An application case is presented in the context of solving a nonlinear regression problem.

An adaptive control technique has been implemented for DSTATCOM for power quality enhancement in three phase four wires(3P4W) distribution system. The reference source currents are extracted from active components of load current for each phase by using this technique. It has also been used for load balancing, harmonic suppression, power factor improvement and reactive power compensation in distribution system. The adaptive control technique has been tested at varying load in steady state and dynamic conditions. This technique is developed using MATLAB/Simulink and source side harmonics are mitigated under different load conditions which are acceptable in accordance with IEEE standard.

Driving simulators are widely used for understanding human-machine interaction, driver behavior and in driver training. The effectiveness of simulators in these process depends largely on their ability to generate realistic motion cues. Though the conventional filter-based motion cueing strategies have provided reasonable results, these methods suffer from poor workspace management. To address this issue, linear MPC-based strategies have been applied in the past. However, since the kinematics of the motion platform itself is non-linear and the required motion varies with the driving conditions, this approach tends to produce sub-optimal results. This paper presents a nonlinear MPC-based algorithm which incorporates the nonlinear kinematics of the Stewart platform within the MPC algorithm in order to increase the cueing fidelity and utilize maximum workspace. Further, adaptive weights-based tuning is used to smoothen the movement of the platform towards its physical limits. Full-track simulations were carried out and performance indicators were defined to objectively compare the response of the proposed algorithm with classical washout filter and linear MPC-based algorithms. The results indicate a better reference tracking with lower root mean square error and higher shape correlation for the proposed algorithm. Lastly, the effect of the adaptive weights-based tuning was also observed in the form of smoother actuator movements and better workspace utilization.

Stability considerations play a central role in structural dynamics to determine states that are robust against perturbations during the operation. Linear stability concepts, such as the complex eigenvalue analysis, constitute the core of analysis approaches in engineering reality. However, most stability concepts are limited to local perturbations, i.e. they can only measure a state’s stability against small perturbations. Recently, the concept of basin stability has been proposed as a global stability concept for multi-stable systems. As multi-stability is a well-known property of a range of nonlinear dynamical systems, this work studies the basin stability of bi-stable mechanical oscillators that are affected and self-excited by dry friction. The results indicate how the basin stability complements the classical binary stability concepts for quantifying how stable a state is given a set of permissible perturbations.

Hasselmann and coauthors proposed the discrete interaction approximation (DIA) as the best tool replacing the nonlinear evolution term in a numerical wind-wave model. Much later, Polnikov and Farina radically improved the original DIA by means of location all the interacting four wave vectors, used in the DIA configuration, exactly at the nodes of the numerical frequency-angular grid. This provides nearly two-times enhancing the speed of numerical calculation for the nonlinear evolution term in a wind-wave model. For this reason, the proposed version of the DIA was called as the fast DIA (FDIA). In this paper we demonstrate all details of the FDIA concept for several frequency-angular numerical grids of high resolution, with the aim of active implementation the FDIA in modern versions of world-wide used wind-wave models.

We consider rational nonlinear electrodynamics with the Lagrangian ${\cal L} = -{\cal F}/(1+2\beta{\cal F})$ (${\cal F}=(1/4)F_{\mu\nu}F^{\mu\nu}$ is the Lorentz-invariant), proposed in \cite{Krug2}, coupled to General Relativity. The effective geometry induced by nonlinear electrodynamics corrections are found. We determine shadow's size of regular non-rotating magnetic black holes and compare them with the shadow size of the super-massive M87* black hole imaged by the Event Horizon Telescope collaboration. Assuming that the black hole mass has a pure electromagnetic nature, we obtain the black hole magnetic charge. The size of the shadow obtained is very close to the shadow size of non-regular neutral Schwarzschild black holes. As a result, we can interpret the super-massive M87* black hole as a regular (without singularities) magnetized black hole.

A mathematical model is proposed for quantitative description of the outbreak of novel coronavirus COVID-19 Although the model is relatively simple, the comparison with the public data shows that an exact solution solution of the model (with the correctly-specified parameters) leads to the results, which are in good agreement with the measured data in China and Austria. Prediction of the total number of the COVID-19 cases is discussed and examples are presented using the measured data in Austria, France and Poland.

This paper proposes a model based on gene expression programming for predicting discharge coefficient of triangular labyrinth weirs. The parameters influencing discharge coefficient prediction were first examined and presented as crest height ratio to the head over the crest of the weir (p/y), crest length of water to channel width (L/W), crest length of water to the head over the crest of the weir (L/y), Froude number (F=V/√(gy)) and vertex angle () dimensionless parameters. Different models were then presented using sensitivity analysis in order to examine each of the dimensionless parameters presented in this study. In addition, an equation was presented through the use of nonlinear regression (NLR) for the purpose of comparison with GEP. The results of the studies conducted by using different statistical indexes indicated that GEP is more capable than NLR. This is to the extent that GEP predicts the discharge coefficient with an average relative error of approximately 2.5% in such a manner that the predicted values have less than 5% relative error in the worst model.

The brain, rather than being homogeneous, displays an almost infinite topological genus, because is punctured with a very high number of topological vortexes, i.e., .e., nesting, non-concentric brain signal cycles resulting from inhibitory neurons devoid of excitatory oscillations. Starting from this observation, we show that the occurrence of topological vortexes is constrained by random walks taking place during self-organized brain activity. We introduce a visual model, based on the Pascal’s triangle and linear and nonlinear arithmetic octahedrons, that describes three-dimensional random walks of excitatory spike activity propagating throughout the brain tissue. In case of nonlinear 3D paths, the trajectories in brains crossed by spiking oscillations can be depicted as the operation of filling the numbers of the octahedrons in the form of “islands of numbers”: this leads to excitatory neuronal assemblies, spaced out by empty area of inhibitory neuronal assemblies. These procedures allow us to describe the topology of a brain of infinite genus, to assess inhibitory neurons in terms of Betti numbers, and to highlight how non-linear random walks cause spike diffusion in neural tissues when tiny groups of excitatory neurons start to fire.

Reliable fatigue design rules affect the proactive identification of safety parameters in aerospace industry. Numerous fatigue crack initiation and propagation models, linear and nonlinear, have been developed for designing purposes or estimation of the remaining life of aging airplanes. Depending on the adopted assumptions, the accuracy varies for different loading histories, loading types, and materials. Semi empirical models are simple but yield significant inaccuracies. Models with better theoretical basis provide better accuracy, but implementation in real conditions is problematic. In the present work, a review of author’s recent fatigue crack initiation and propagation models based on physical mechanisms is presented and improvements are proposed. Verification of the models on test results is provided and discussed.

Imperfection sensitivity of large amplitude vibration of curved single-walled carbon nanotubes (SWCNTs) is considered in this study. The SWCNT is modeled as a Timoshenko nano-beam and its curved shape is included as an initial geometric imperfection term in the displacement field. Geometric nonlinearities of von Kármán type and nonlocal elasticity theory of Eringen are employed to derive governing equations of motion of nano-beam. Spatial discretization of governing equations and associated boundary conditions is performed using differential quadrature (DQ) method and the corresponding nonlinear eigenvalue problem is iteratively solved. Effects of value and location of the geometric imperfection, and the nonlocal small-scale parameter on the nonlinear frequency ratio and imperfection sensitivity of a curved SWCNT for various boundary conditions are investigated. The results show that the geometric imperfection plays a significant role in the nonlinear vibration characteristics of curved SWCNTs.

In economics, especially econometrics, fixed-effects are widely recognized as powerful tools for heterogeneity analysis of longitudinal data sets. However, the existing research pays more attention to such as the variable selection, parameter estimation and dimension reduction on linear relationships with too many assumptions while nonlinear relationships are ubiquitous. In this paper, an extension fixed-effects model is proposed on the curve_fit nonlinear least squares. First, with the help of expert knowledge, the series regressions between independent variables including time and dependent variable is estimated on each series data, and the parameters are estimated by curve_fit. Similarly, the coeffection between independent variables including time and dependent variable is also initially estimated on the whole panel data. Second, the distance between regressions is defined, and then the coeffect function between the series regressions is obtained on the initial co-effect with curve_fit. Third, the time-effects and individual fixed-effects for each series data in the panel data are estimated on the differences of series regressions and co-effect function. Additionally, the effectiveness of the proposed method is varified on the synthetic data.

This research aims to investigate psychological anxiety factors, particularly Music Performance Anxiety (MPA), that influence the sustainability of music learning systems. This study employs an innovative integration of qualitative and quantitative methodologies, marking the first use of a nonlinear system paired with a comprehensive data framework for analyzing questionnaire responses. This approach allows for a detailed examination of the effects of these factors on academic outcomes. Previous research has primarily focused on the fragmented music learning system from the perspective of teachers' instructional strategies, emphasizing phased teaching methods and learning objectives which focus often neglected a significant subset of music learners. Addressing this oversight, the current study specifically centers on the emotional aspects of anxiety within music learning systems, with a particular emphasis on students, who play a crucial role in music education. This perspective enables a deep exploration of how MPA and other related emotional factors affect music learning systems. A notable innovation of this research is the development of a stochastic nonlinear system designed to model the psychological factors impacting student music learning, complemented by a quantitative model that assesses actual learning outcomes. By analyzing this nonlinear system, the research identifies weight values for various negative emotions, particularly those related to MPA, that significantly influence the music learning process. The integration of MPA and other anxiety related emotional factors with practical learning outcomes provides a comprehensive understanding of their combined impact on the music learning system. These insights are invaluable for educators and policymakers aiming to enhance both the effectiveness and emotional well-being within music education. This comprehensive approach offers a novel perspective in understanding and improving the dynamics of music education through a more empathetic and scientifically grounded lens.

Nonlocal theories are gaining prominence because they can solve problems which lead to unphysical conclusions in standard models. This study presents a novel fractional boundary element method (BEM) solution for nonlinear nonlocal thermoelastic problems of anisotropic fibrous polymer nanomaterials. This broad BEM solution combines two solutions: anisotropic fibrous polymer nanomaterials problem solution and nonlinear nonlocal thermoelasticity problem solution. The nonlinear nonlocal thermoelasticity problem solution divides the displacement field into complementary component and particular component. The overall displacement is generated using the boundary element technique, which is the solution to a Navier type problem, while the particular displacement is derived using local radial point. The New Modified Shift-Splitting (NMSS) approach, which reduces memory and processing time requirements, was used to solve linear systems created by BEM. Figures demonstrate the numerical findings, which show the effects of fractional and graded parameters on the thermal stresses of nonlinear nonlocal thermoelastic problems of anisotropic fibrous polymer nanomaterials. The numerical results indicate the consistency and efficiency of the proposed methodology.

In this paper, we propose a system of nonlinear mixed variational inequality problems, which consists of two elliptic mixed variational inequality problems on Banach spaces. Under suitable assumptions, using the Kakutani-Ky Fan fixed point theorem and Minty techniques, we prove the solution set to the system of nonlinear mixed variational inequality problem is nonempty, weakly compact and unique. Additionally, we suggest a stability result for the system of nonlinear mixed variational inequality problem by perturbing the duality mappings. Furthermore, we present an optimal control problem governed by the system of nonlinear mixed variational inequality problems and establish a solvability result.

In this paper, we consider an epidemiological Susceptible-Infected-Susceptible (SIS) model in which the individuals cured from the infection return back into the group of people endangered by the infection. Delay differential equations were introduced to create more realistic models since many processes depend on past history. Many different mathematical methods, including the Susceptible-Infected-Recovered (SIR) model as well as derivatives thereof, can be used to prognose the spread of many various infectious diseases, including Covid-19.We use a nonlinear differential system with time delay as a mathematical formulation of this model. It is examined by the existence of a positive solution which is bounded by two functions $k_1, k_2\in C([t_0,\infty),(0,\infty))$ with constants $\lambda_1 > 0,\,\lambda_2 > 0$ where $0<\lambda_1\leq \lambda_2$. The conditions are put in place for existence of a positive solution that approaches zero in infinity, if $t\to\infty$. Infectious diseases accompany a person throughout their entire life, and in the history of mankind often appeared in frequent epidemics caused high mortality. The occurrence of infectious diseases in the population represents a serious health, social and economic problem. There is a lot of ambiguity concerning the time span and final spread of the epidemic thus making it very demanding for the governing bodies, healthcare institutions, and economic sector to precisely judge the future development.Several examples are shown at the end of this paper.

In this paper, we present a three-step sixth-order iterative schemes to estimate the solutions of a nonlinear systems of equations, for predicting the shear strength of a reinforced concrete beam. This procedure is designed by means of a weight function technique. The values for the parameters of this system were randomly selected inside the prescribed ranges by technical standards for structural concrete; moreover, some of this parameters were fixed taking into consideration the solvability region of the adopted steel constitutive model. The efficiency of the new class is compared with other current schemes, with very good results.

In this paper, a swarm trajectory planning method is proposed for multiple autonomous surface vehicles (ASVs) in an unknown and obstacle-rich environment. Specifically, based on the point cloud information of the surrounding environment obtained from local sensors, a kinodynamic path searching method is used to generate a series of waypoints in the discretized control space at first. Next, after fitting B-spline curves to the obtained waypoints, a nonlinear optimization problem is formulated to optimize the B-spline curves based on gradient-based local planning. Finally, a numerical optimization method is used to solve the optimization problems in real-time to obtain collision-free, smooth and dynamically feasible trajectories relying on a shared network. Simulation results demonstrate the effectiveness and efficiency of the proposed swarm trajectory planning method for a network of ASVs.

We have investigated the canine of olive flounder in terms of the nonlinear optical signals of two-photon excitation autofluorescence (2PEF) and second harmonic generation (SHG), whereby two kinds of nonlinear microscope images of the canine were obtained using ~140 femtosecond pulses. For increasing excitation power of laser pulses, a photobleaching effect was found to be significant in the red and green ranges of autofluorescence, where a double-exponential decay of the intensity occurs within hundreds of second due to collagen fluorophores in the canine. In the blue range of autofluorescence, the photobleaching is suppressed due to an energy conversion of the incident laser pulse to SHG signal. As a result, the signal in blue range remains constant for long term exposure to laser. We have also found that the SHG intensity depends on the orienta-tion of linearly polarized excitation, and the optical anisotropy of SHG can be attributed to the collagen alignment of canines.

Despite the fact that SMA restrainers exhibit a superelastic strain capacity of 7%, this capacity appears inadequate for isolated bridges due to the typically greater than 20cm relative dis-placements between girders during intense seismic events. In order to perform such a stroke, a SMA restrainer of greater than 3 metres in length might be required. In order to reduce the length of restrainers, a novel honeycomb damper constructed from superelastic shape memory alloy (SMA) is proposed. The proposed device, denoted as the superelastic SMA honeycomb damper (SHD), is comprised of steel plates to prevent the SMA plane from collapsing and superelastic SMA honeycomb to provide self-centering capability. By incorporating the large strain capacity of SMA and the geometrically nonlinear deformation of honeycomb structures, SHD has been developed to satisfy the requirements of bridge restrainers with large strokes. It is capable of functioning as a restrainer and energy dissipation device when subjected to dynamic tension and compression loads. The SHD was initially investigated from a theoretical perspective. Following this, a mul-ti-cell SHD specimen was manufactured. The specimen underwent axial tensile and compressive experiments in order to examine the mechanical properties of SHDs. Finally, experimental results were investigated through numerical simulation analyses of the SHDs using a three-dimensional high-fidelity finite element model. Additionally, a method for enhancing SHD was proposed. The findings indicate that SHD is capable of exhibiting superior self-centering capability and sta-ble hysteretic responses when subjected to earthquakes.

We report a diode pumped solid state (DPSS) laser used for intracavity pump-enhanced difference frequency generation (DFG) to create a 3.5 micron laser. Using a 50 mm-long periodically poled lithium niobate (PPLN) crystal inside the cavity of an Nd:YVO4 solid state laser at 1064 nm with 4.5 W pump power at 808 nm, and a 310 mW C-band signal at 1529 nm, up to 31 mW of mid-infrared output power at 3499 nm is obtained. The cavity requires no active stabilization and/or locking, and the entire cavity is &lt;8 cm in length. The obtained output power corresponds to a black box efficiency of 2.20 %W-1, which is the highest value reported to date for continuous wave DFG based on a bulk nonlinear optical crystal with no active stabilization. Potential future applications in free space optical communication are discussed as well.

This paper discusses the mathematical modelling of exothermic explosions in a slab. This model is based on a nonlinear equation containing a nonlinear term related to Arrhenius, bimolecular, and sensitised laws of reaction kinetics. The absolute temperature can be obtained by solving the nonlinear equation using Akbari-Ganji’s method. The influence of the parameters Frank-Kamenetskii, activation energy and numerical exponent on temperature is discussed. The analytical results are compared with previous available analytical and numerical results ( Matlab). A satisfactory agreement is noted.

The total tree height (h) and diameter at breast height (dbh) relationship is an essential tool in forest management and planning. The height—diameter (h-dbh) relationship had been studied with several approaches and for several species worldwide. The nonlinear mixed effect modeling (NLMEM) has been extensively used and lately the resilient backpropagation artificial neural network (RBPANN) approach has been a trend topic for modeling this relationship. The artificial neural network (ANN) is a computing system based in artificial intelligence and inspired in biological neural network for supervised learning. In this study the NLMEN and RBPANN approaches were used for modeling the h—dbh relationship for Durango pine species (Pinus durangensis Martínez) in mixed-species forest from Mexico. The total dataset considered 1,000 (11,472 measured trees) randomly selected from 14,390 temporary forest inventory plots and the dataset was randomly divided into two parts; 50% for training and 50% for testing. An unsupervised clustering analysis was used to grouped the dataset into 10 clusters based on k-means clustering method and plot-variables like density, basal area, mean dbh, mean h, quadratic mean diameter, altitude and aspect. The RBPANN was performed for tangent hyperbolicus (RBPANN-tanh), softplus (RBPANN-softplus), and logistic (RBPANN-logistic) activation functions for functions in cross product of the covariate or neurons and the weights for the ANN analysis. For both training and testing, 10 classical statistics (e.g., RMSE, R2, AIC, BIC, logLik) were computed for the residual values and assess the approaches for h—dbh relationship. For training and testing, the ANNs approach outperformed the NLMEM approach, and the RBPANN-tanh has the best performance in both training and testing phases.

The heat release response of the flame to acoustic excitation is a critical factor for understanding combustion instability. In the present work, the nonlinear heat release response of a methane-air non-premixed flame to the low frequency acoustic excitations is experimentally investigated. The flame describing function (FDF) was measured based on the overall CH* chemiluminescence intensity and the velocity fluctuations obtained by two-microphone method. The CH* chemiluminescence images and the schlieren images were analyzed to reveal the mechanism of nonlinear response. The excitation frequency ranges from 10Hz to 120Hz. The forced relative velocity fluctuation amplitude ranges from 0.10 to 0.50. The corresponding flame Strouhal number (Stf) ranges from 0.43 to 4.67. The study has shown that the flame length responds more sensitively to changes in excitation amplitude when subjected to relatively high frequency excitations. The normalized flame length (Lf/D) decreases from 3.79 to 2.37 with the increase of excitation amplitude at excitation frequency of 100Hz. The number of oscillation zones along the flame increases with increasing excitation frequency, which is consistent with the increase of the Stf. The low-pass filtering characteristic of FDF is caused by the dispersion of multiple oscillation zones, as well as the cancellation effect of the adjacent oscillation zones under relatively high frequency excitation. The cancellation effect of the positive and negative oscillation zones with various Stf is main mechanism for the local gain peak and valley. When two adjacent oscillation regions have approximate amplitudes, the overall phase-lag becomes more sensitive to changes in excitation frequency and amplitude. This sensitivity leads to nonlinear anomalous changes in the phase-lag near the frequency corresponding to the gain valley. The calculated disturbance convection time is consistent with the measured time delay in the short flame scenario. Future research is necessary to establish whether the observed agreement occurs due to the oscillation zone consistently occurring proximate to the flame's center of mass, coupled with a precise determination of the average convective velocity.

Chaotic systems are systems whose results are sensitive to the initial conditions. Chaotic systems generally have nonlinearities that can be difficult to model. One example of a chaotic system with nonlinearities is the Lorenz system. The Lorenz system can be used to model weather, wind disturbances, and electronic circuit design, among other applications. In this manuscript, the Lorenz system is modeled and various control methods are applied in an effort to dictate the system’s state and rate trajectories. The combination of the linear feedback and nonlinear feedforward controllers can show over an 80% improvement in state trajectory errors when compared to the baseline run. However, the improved state trajectory performance comes at a cost of as much as 1800% error in the rate trajectories.

For a decade, the studies of dynamic control for unmanned aerial vehicles took a large interest, where drones as a useful technology in different areas were always suffering from several issues like instability-high energy consumption of batteries - inaccuracy of tracking targets. Different approaches are proposed for dealing with the non-linearity issues which present the most important features of this system. This paper describes our focus on the most common control strategies, known as model predictive control MPC, by developing a model based on the sensors embedded in our Tello quadrotor used for indoor purposes. The original controller of Tello quadrotor is supposed to be a slave, where the designed model predictive controller is created in MATLAB and imported to another embedded system, considered as a master; the objective of this model is to track the reference trajectory, almost keeping the stability of the system and ensure the low energy consumption. In the first part, a profound description of the modelling process of a dynamic model for drones is presented, explaining the design of MPC controller with both linear and non-linear strategies built in MATLAB. In the final part, simulation and results are discussed regarding its behaviour and performance, highlighting the MPC model's important role on drones' energy consumption profile.

We experimentally demonstrate enhanced spectral broadening of femtosecond optical pulses after propagation through silicon-on-insulator (SOI) nanowire waveguides integrated with two-dimensional (2D) graphene oxide (GO) films. Owing to the strong mode overlap between the SOI nanowires and the GO films with a high Kerr nonlinearity, the self-phase modulation (SPM) process in the hybrid waveguides is significantly enhanced, resulting in greatly improved spectral broadening of the femtosecond optical pulses. A solution-based, transfer-free coating method is used to integrate GO films onto the SOI nanowires with precise control of the film thickness. Detailed SPM measurements using femtosecond optical pulses are carried out, achieving a broadening factor of up to ~4.3 for a device with 0.4-mm-long, 2 layers of GO. By fitting the experimental results with theory, we obtain an improvement in the waveguide nonlinear parameter by a factor of ~3.5 and the effective nonlinear figure of merit (FOM) by a factor of ~3.8, relative to the uncoated waveguide. Finally, we discuss the influence of GO film length on the spectral broadening and compare the nonlinear optical performance of different integrated waveguides coated with GO films. These results confirm the improved nonlinear optical performance for silicon devices integrated with 2D GO films.

Training supervised machine learning models requires labeled examples. A judicious choice of examples is helpful when there is a significant cost associated with assigning labels. This article improves upon a promising extant method – Batch-mode Expected Model Change Maximization (B-EMCM) method – for selecting examples to be labeled for regression problems. Specifically, it develops and evaluates alternate strategies for adaptively selecting batch size in B-EMCM. By determining the cumulative error that occurs from the estimation of the stochastic gradient descent, a stop criteria for each iteration of the batch can be specified to ensure that selected candidates are the most beneficial to model learning. This new methodology is compared to B-EMCM via mean absolute error and root mean square error over ten iterations benchmarked against machine learning data sets. Using multiple data sets and metrics across all methods, one variation of AB-EMCM, the max bound of the accumulated error (AB-EMCM Max), showed the best results for an adaptive batch approach. It achieved better root mean squared error (RMSE) and mean absolute error (MAE) than the other adaptive and non-adaptive batch methods while reaching the result in nearly the same number of iterations as the non-adaptive batch methods.

Gol'denveizer's problem of a torus has been analyzed by Audoly and Pomeau (2002) and Sun (2021). However, all of the investigations of Gol'denveizer's problem of an elastic torus have been linear. In this paper, the finite element method is used to more accurately address this problem. Furthermore, Sun (2021) cannot be solved by nonlinear analysis. We research the nonlinear mechanical properties of Gol'denveizer's problem of circular and elliptic tori, and relevant nephograms are given. We study the buckling of Gol'denveizer's problem of an elastic torus, and propose failure patterns and force-displacement curves of tori in the nonlinear range. Investigations reveal that circular tori have more rich buckling phenomena as the parameter a increases. Gol'denveizer's problem of the buckling of an elliptic torus is analyzed, and we find a new buckling phenomenon called a "skirt." As a/b increases, the collapse load of an elliptic torus of the Gol'denveizer problem is enhanced gradually.

Satellite Image Time Series (SITS) is a data set which includes satellite images across several years with a high acquisition rate. Radiometric normalization is a fundamental and important preprocessing method for remote sensing applications using SITS due to the radiometric distortion caused by noise between images. Normalizing the subject image based on the reference image is a general strategy when using traditional radiometric normalization methods to normalize multi-temporal imagery (usually two scenes or three scenes in different time phases). However, these methods are not suitable for calibrating SITS because they cannot minimize the radiometric distortion between any pair of images in SITS. The existing relative radiometric normalization methods for SITS are based on linear assumptions which cannot effectively reduce nonlinear radiometric distortion caused by continuously changing noise in SITS. To overcome this problem and obtain a more accurate SITS, this study proposed a Nonlinear Radiometric Normalization Model (named NMAG) for SITS based on Artificial Neural Networks (ANN) and Greedy Algroithm (GA) . In this method, GA was used to determine the correction order of SITS and calculate the error between the image to be corrected and normalized images, which avoided the selection of a single reference image. ANN was used to obtain the optimal solution of error function, which minimized the radiometric distortion between different images in SITS. SITS composed of 21 Landsat-8 images in Tianjin City from October 2017 to January 2019 were selected to test the method. We compared NMAG with other two contrasting method (refered as CM1 and CM2), and found that the average of root mean square error $(\mu_{RMSE})$ of NMAG $(497.22)$ was significantly smaller than those of CM1 $(641.39)$ and CM2 $(543.47)$, and the accuracy of normalized SITS obtained by using NMAG has increased by 22.4\% and 8.5\% toward CM1 and CM2, respectively. These experimental results confirmed the effectiveness of NMAG in the reduction of radiometric distortion caused by continuously changing noise between images in SITS.

We report on space-selective crystallization of congruent and polar Sr2TiSi2O8 crystals in a stoichiometric SrO-TiO2-SiO2 glass induced by (1030 nm, 300 fs) femtosecond laser irradiation. This allows us to compare with non-congruent laser induced crystallization of polar LiNbO3, in non stoichiometric Li2O-Nb2O5-SiO2 glass and gain information on the mechanism of nanocrystals orientation with the laser polarization that we pointed out previously. Using scanning electron microscopy (SEM), Second-harmonic generation (SHG) and electron backscattered diffraction (EBSD), we studied the laser induced crystallization according to the laser processing parameters (pulse energy, pulse repetition rate, scanning speed). We found 1) a domain where the laser track is filled with crystals not perfectly textured (low energy), 2) a domain where an amorphous volume remain surrounded by a crystallized shell (high energy). This arises from Sr out-diffusion and may gives rise to crystallization of both SrTiO3 and Sr2TiSi2O8 phases at low speed. In the one-phase domain (at higher speed), it is found the possibility to elaborate a tube with a perfect fresnoite texture. Significant difference in size and morphology whereas crystallization threshold remains similar are discussed based on glases thermal propeties. Contrarily to Li2O-Nb2O5-SiO2 (LNS) glass, no domain of oriented nanocrystallization controlled by the laser polarization has been found in SrO-TiO2-SiO2 (STS) glass, which is attributed to the larger crystallization speed in STS glass. No nanogratings have also been found that is likely due to the congruency of the glass.

This study presents a new kinetic scheme for the mass yield prediction of waste lignocellulosic biomasses treated by Hydrothermal Carbonization (HTC). The proposed reactions are based on the decomposition, solubilization, and polymerization of each main fraction of the biomass: cellulose, hemicellulose, and lignin. The ash content was assumed to be inert. The kinetic parameters have been obtained by non-linear adjustment using a data set with 220 experimental runs collected from the literature. The results indicate that the pre-exponential factors range was from 7.33 x10¹ to 1.412x10⁵ min^-1, and activation energies were between 33.75 y 225.3 kJ/mol. A good fit is achieved between the observed and predicted data with an R² of 0.81 and an RMSE of 7.7 %. The proposed scheme was validated with the experimental data obtained by the HTC of sawdust (Pinus radiata) and rapeseed (Brassica napus). The experiments were carried out at temperatures of 190, 220, and 250 ºC and reaction times of 0, 30, 60, 90, and 120 min. The predicted values showed an average error of 2.3 and 3.5 %, respectively. Therefore, the kinetic scheme is a useful tool in the conversion analysis of waste biomass treated by HTC.

In this paper, we generalize the problems of finding simple polygons with the minimum area, maximum perimeter and maximum number of vertices so that they contain a given set of points and their angles are bounded by $\alpha+\pi$ where $\alpha$ ($0\leq\alpha\leq \pi$) is a parameter. We also consider the maximum angle of each possible simple polygon crossing a given set of points, and derive an upper bound for the minimum of these angles. The correspondence between the problems of finding simple polygons with the minimum area and maximum number of vertices is investigated from a theoretical perspective. We formulate the three generalized problems as nonlinear programming models, and then present a Genetic Algorithm to solve them. Finally, the computed solutions are evaluated on several datasets and the results are compared with those from the optimal approach.

For a dynamical system, it is known that the existence of a Lyapunov density implies almost global stability of an equilibrium. It is then natural to ask whether the existence of a common Lyapunov density for a nonlinear switched system implies almost global stability, in the same way as a common Lyapunov function implies global stability for nonlinear switched systems. In this work, the answer to this question is shown to be affirmative as long as switchings satisfy a dwell-time constraint with an arbitrarily small dwell time. As a straightforward extension of this result, we employ multiple Lyapunov densities in analogy with the role of multiple Lyapunov functions for the global stability of switched systems. This gives rise to a minimum dwell time estimate to ensure almost global stability of nonlinear switched systems, when a common Lyapunov density does not exist. The results obtained for continuous-time switched systems are based on some sufficient conditions for the almost global stability of discrete-time non-autonomous systems. These conditions are obtained using the duality between Frobenius-Perron operator and Koopman operator.

In this paper, we define new kind of Daehee numbers, the degenerate Daehee numbers of the third kind, using degenerate log function as generating function. We obtain some identities for the degenerate Daehee numbers of the third kind associated with the Daehee, degenerate Daehee and degenerate Daehee numbers of the second kind. In addition, we derive a differential equation associated with the degenerate log function. We deduce some identities from the differential equation.

Increasing of the imaging rate of conventional atomic force microscopy (AFM) is almost impossible without impairing of the imaging quality, since the probe tip tends to lose contact with the sample. We propose to apply the additional nonlinear force on the upper surface of a cantilever, which will help to keep the tip and surface in contact. In practice this force can be produced by the precisely regulated airflow. Such an improvement affects the AFM system dynamics, which were evaluated using a mathematical model presented in this paper. The model defines the relationships between the additional nonlinear force, the pressure of the applied air stream and the initial air gap between the upper surface of the cantilever and the end of the air duct. It was found that the nonlinear force created by the stream of compressed air (aerodynamic force) prevents the contact loss caused by the high scanning speed or higher surface roughness, and at the same time has minimal influence on the interaction force, thus maintaining stable contact between the probe and the surface. This improvement allows to effectively increase the scanning speed by at least 10 times using a soft (spring constant of 0.2 N/m) cantilever by applying the air pressure of 40 Pa. If a stiff cantilever (spring constant of 40 N/m) is used, the potential of accuracy improvement reaches 92 times. This method is suitable for use with different types of AFM sensors and can be implemented practically without essential changes in AFM sensor design.

During speciation-with-gene-flow, a transition from single-locus to multi-locus processes can occur, as strong coupling of multiple loci creates a barrier to gene flow. Testing predictions about such transitions with empirical data requires building upon past theoretical work and the continued development of quantitative approaches. We simulated genomes under different evolutionary scenarios of gene flow and divergent selection, extending previous work with the additions of neutral sites and coupling statistics, allowing us to investigate if and how selected and neutral sites differ in the conditions they require for transitions during speciation. As the per-locus strength of selection grew and/or migration decreased, it became easier for selected sites to show divergence – and thus to rise in linkage disequilibrium (LD) with each other as a statistical consequence – farther in advance of the conditions under which neutral sites could diverge. Indeed, even very low rates of gene flow were sufficient to prevent differentiation at neutral sites. However, once strong enough, coupling among selected sites eventually reduced gene flow at neutral sites as well. To explore whether similar transitions might be detectable in empirical data, we used published genome resequencing data from three taxa of Heliconius butterflies. We found that allele-frequency outliers and F ST outliers exhibited stronger patterns of LD than the genomic background, as expected. The statistical characteristics of LD – likely indicative of the strength of coupling of barrier loci – varied between chromosomes and taxonomic comparisons. Broad qualitative agreement between the patterns we observed in the empirical data and our simulations suggests that selection drives rapid genome-wide transitions to multi-locus coupling, illustrating how divergence and gene flow interact along the speciation continuum.

MEMS (Micro-electromechanical Systems) becomes important increasingly due to the smarter and smaller fuze used in OICW (Objective Individual Combat Weapon). MEMS Safety and Arming (S&A) device is employed in different platforms and regions for small caliber projectile. Therefore, it is necessary to make a parametric study of the MEMS S&A device in different apply environments and explore the main sensitive factors of the MEMS S&A device to provide reference for designs. In this paper, based on the MEMS S&A device designed by our term, theory and finite element models are established, and the centrifugal insurance mechanism of the MEMS S&A device is parametric studied under the different speeds, temperature and thickness of the model by nonlinear dynamic method. By comparing the experimental and predicted results, the established FEM model is verified, and the conclusion is that the temperature and the centrifugal force are the main sensitive factors in the centrifugal insurance mechanism. In summary, we can suggest that the application environment, which the MEMS S&A device is suitable for, is the temperature equal to or slightly greater than normal temperature and the rotating speed higher than35000r/min of small caliber projectile.

Reviewed the research progress of Newton’s iterative methods for nonlinear equation. Convergence with second order, third order, fourth order, fifth order, sixth order, seventh order, eighth order and ninth order Newton’s iterative methods are given in turn, and the efficiency index of these iterative methods are analyzed. Numerical experiments show that the convergence process of the three Newton iterative methods, and the results indicate that the convergence of the higher-order Newton’s method can be well demonstrated only when the initial point is close to the root.

The bulk LiNa5Mo9O30 (LNM) crystals were successfully grown in the [010] and [001] directions without internal inclusions and cracks by the Czochralskii method with low temperature gradient. The crystal grown in the [010] direction showed a tendency to twinning. The crystal grown in the [001] direction demonstrated high structural perfection (FWHM=13'') for the (001) plane and high optical quality Δn≈210-5. The laser induced damage threshold was measured along a, b and c axes and was 15.7, 27.0 and 27.5 J/cm2 respectively. The thermo-optical coefficient dn/dT was measured for the main crystallographic axes, which was -5.7510-6, -2.0210-5 and 3.6510-6 K-1 along the a, b and c axes, respectively. The second harmonic generation (SHG) is conducted in crystalline LNM sample. The maximum efficiency value of 3.5% at pump power of 12 W had been achieved.

Automatic emotion recognition using portable sensors is gaining attention due to its potential use in real-life scenarios. Existing studies have not explored Galvanic Skin Response and Photoplethysmography sensors exclusively for emotion recognition using nonlinear features with machine learning (ML) classifiers such as Random Forest, Support Vector Machine, Gradient Boosting Machine, K-Nearest Neighbor, and Decision Tree. In this study, we proposed a genuine window sensitivity analysis on a continuous annotation dataset to determine the window duration and percentage of overlap that optimize the classification performance using ML algorithms and nonlinear features, namely Lyapunov Exponent, Approximate Entropy, and Poincaré’s indices. We found an optimum window duration of 11 seconds and 16 seconds for valence and arousal, respectively, with 50% overlap, and achieved an accuracy of 0.76 in both dimensions. In addition, we proposed a Strong Labeling Scheme that kept only the extreme values of the labels, which raised the accuracy score to 0.92. Under certain conditions mentioned, traditional ML models offer a good compromise between performance and low computational cost. Our results suggest that well-known ML algorithms can still contribute to the field of emotion recognition, provided that window duration, overlap percentage, and nonlinear features are carefully selected.

The abstract should be an objective representation of the article and it must not contain results that are not presented and substantiated in the main text and should not exaggerate the main conclusions. The study developed a novel method for evaluating the freshness of citrus fruits by integrating near-infrared spectroscopy with the nonlinear data processing capabilities of a BP neural network. This approach utilizes specific wavelength analysis to distinguish between fresh and non-fresh fruits effectively. Advanced preprocessing techniques are employed to remove spectral anomalies, enhancing the network's ability to accurately identify crucial quality indicators like sugar content. Concurrently, an experiment utilising a MATLAB-based BP neural network optimised the number of hidden layer nodes, identifying 61 as optimal. This configuration achieved impressive metrics, including a mean squared error of 0.0025665 and a root mean squared error of 49.8214, over 1000 training iterations with an 80% learning rate. The model demonstrated a high accuracy rate of 97.6275%, confirming its precision and reliability in assessing citrus freshness. This synergy between advanced neural network processing and spectroscopic techniques marks a significant advancement in agricultural quality assessment, setting new standards for speed and efficiency in data processing.

Artificial intelligence (AI) systems of autonomous systems such as drones, robots and self-driving cars may consume up to 50% of total power available onboard, thereby limiting the vehicle’s range of functions and considerably reducing the distance the vehicle can travel on a single charge. Next-generation onboard AI systems need an even higher power since they collect and process even larger amounts of data in real time. This problem cannot be solved using the traditional computing devices since they become more and more power-consuming. In this review article, we discuss the perspectives of development of onboard neuromorphic computers that mimic the operation of a biological brain using nonlinear-dynamical properties of natural physical environments surrounding autonomous vehicles. Previous research also demonstrated that quantum neuromorphic processors (QNPs) can conduct computations with the efficiency of a standard computer while consuming less than 1% of the onboard battery power. Since QNPs is a semi-classical technology, their technical simplicity and low, compared with quantum computers, cost make them ideally suitable for application in autonomous AI system. Providing a perspective view on the future progress in unconventional physical reservoir computing and surveying the outcomes of more than 200 interdisciplinary research works, this article will be of interest to a broad readership, including both students and experts in the fields of physics, engineering, quantum technologies and computing.

Forest resources are renewable,rational exploitation and utilization of forest resources are not only conducive to sustainable development of population, but also can obtain higher economic benefits. Based on actual timber harvesting problems,a combined harvesting model of timber and non-timber with nonlinear harvesting term was established.Firstly, using the qualitative theory of ordinary differential equations, the dynamic behavior of the model is studied, and the existence and stability of the equilibrium point of the model are proved .Secondly, the optimal control solution is obtained by using the optimal control theory.Finally, the optimal harvesting strategy of timber and non-timber products is given based on the numerical simulation results, which provides a certain theoretical basis for the sustainable development of forestry ecological economy.

The penetrability and directivity of ultrasound in different media is of interest in engineering and medical applications (imaging, nondestructive testing, sonochemistry, among others). The nonlinearity of a liquid can be used in the parametric antenna framework to generate low-frequency components with particular features from several ultrasonic signals at the source. Bubbly liquids are dispersive liquids in which a small amount of tiny gas bubbles leads to the increase of the nonlinear parameter of the media over certain frequency ranges. Parametric antenna applied to this huge nonlinear media gives rise to low-frequency components with relatively small intensity at the source. The evolution of a low-frequency component (difference-frequency component obtained from two primary signals) during its propagation in a bubbly liquid is somehow unknown. It is thus interesting to analyse its characteristics to establish whether this component can benefit from the quality of its own frequency and from the primary frequencies in terms of directivity and penetrability into the medium. It must be noted that no such study in bubbly liquids exists in the litterature, but only for homogeneous media. To this end, several numerical models developed previously are used here to analyse the difference-frequency component obtained from a parametric antenna emitting from two ultrasonic signals at the source in one and two-dimensional domains. These models allow us to observe the behavior of this frequency component. An angle that measures the directivity of a beam is also defined. Our results show a point hardly found in the literature: the high directivity and the huge penetrability of the secondary beam associated to the difference-frequency component into the bubbly liquid, compared to the same frequency signal excited directly from the source in the bubbly liquid and to the parametric acoustic array in homogeneous fluids.

In addition to their importance in statistical thermodynamics, probabilistic entropy measurements are crucial for understanding and analyzing complex systems, with diverse applications in time series and one-dimensional profiles. However, extending these methods to two- and three-dimensional data still requires further development. In this study, we present a new method to classify spatiotemporal processes based on entropy measurements. To test and validate the method, we selected four classes of similar processes related to the evolution of random patterns: dynamic colored noises ((i)~white and (ii)~red); (iii)~weak turbulence from reaction-diffusion; (iv)~hydrodynamic fully developed turbulence, and (v)~plasma turbulence from MHD. Considering seven possible ways to measure entropy from a matrix, we present the method as a parameter space composed of the two best separating measures of the five selected classes. The results highlight better combined performance of Shannon Permutation Entropy ($S^p_H$) and a new approach based on Tsallis Spectral Permutation Entropy ($S^s_q$). Notably, our observations reveal the segregation of reaction terms in this $S^p_H \times S^s_q$ space, a result that identifies specific sectors for each class of dynamic process, and can be used to train machine learning models for automatic classification of complex spatiotemporal patterns.

The goal of this article is to provide a review of the experimental techniques and procedures using vibration methods for the Structural Health Monitoring (SHM) of Polymer-Matrix Composites (PMC). It aims to be a guide for any researchers to carry out vibration experiments. The linear methods are first introduced. But as PMC is a complex material, these classic methods showed some limits, such as low accuracy for small damages, and a high environmental dependency. This is why the nonlinear methods are secondly studied, considering that the complexity of PMC induces a nonlinear behavior of the structure after damage occurrence. The different damage mechanisms are well explained in order to evaluate the potential of each vibration method to detect them.

In wireless sensor networks (WSNs) deployed in smart agriculture systems, accurately determining the locations of sensor nodes is crucial for efficient monitoring and control. However, in many cases, the exact positions of certain sensor nodes may be unknown. To address this challenge, this paper presents a novel method for localizing unknown sensor nodes in WSN-based smart agriculture systems using range measurements. The proposed method utilizes the Levenberg-Marquardt optimization algorithm to solve a nonlinear least squares problem and minimize the error in estimating the unknown node locations. By leveraging the known positions of a subset of sensor nodes and the inexact distance measurements between pairs of nodes, the localization problem is transformed into a nonlinear optimization problem. To validate the effectiveness of the approach, extensive simulations and experiments were conducted. The results demonstrate that the proposed method achieves accurate localization of the unknown sensor nodes, effectively enhancing the overall performance of the WSN-based smart agriculture system. Furthermore, the method demonstrates robustness against measurement noise and scalability for large-scale networks. The practical implications of this research extend beyond smart agriculture systems, as the proposed method can be applied to various WSN applications where precise node localization is essential.

Reservoir computing (RC) systems can efficiently forecast chaotic time series using nonlinear dynamical properties of an artificial neural network of random connections. The versatility of RC systems has motivated further research on both hardware counterparts of traditional RC algorithms and more efficient RC-like schemes. Inspired by the nonlinear processes in a living biological brain and using solitary waves excited on the surface of a flowing liquid film, in this paper we experimentally validate a physical RC system that substitutes the effect of randomness for a nonlinear transformation of input data. Carrying out all operations using a microcontroller with a minimal computational power, we demonstrate that the so-designed RC system serves as a technically simple hardware counterpart to the `next-generation’ improvement of the traditional RC algorithm.

This paper studies the trajectory tracking control of an autonomous underwater vehicle (AUV) based on a stochastic uncertain nonlinear system. We investigate the time-varying gain adaptive control method looking for possible approaches to alleviate the heavy computational burden. Under nonlinear growth, conditions satisfy polynomial growth conditions. These two problems are resolved the fast response time and good path tracking, respectively. Novel adaptive algorithms are developed exploiting the dynamic properties of the AUV motion. By appropriately turning the original controller design problems into parameters choosing problems and then solving them in a functional time-varying observer technical theorem. In order to deal with the station error of system converges to arbitrarily small domains with stochastic uncertain disturbance. A coordinate transformation is proposed for all system states to meet boundedness. We show that the convergence of the AUV trajectory errors can be guaranteed by the proposed contraction constraints in the stability analysis, closed-loop stability is proved, and the system is asymptotically probabilistic in the global scope. They are taking advantage of the guaranteed stability. Extensive simulation studies on the AUV model demonstrate the effectiveness and robustness of the proposed approach. A real-time time-varying gain constructive control strategy is further developed for the Hardware-in-the-loop simulation; the controller design results are imported into the AUV actuator model to verify the effectiveness of the controller design.

In the last years, a recent growing line of research has been developed with fruitful results by using fractional and conformable derivatives in the iterative procedures of classical methods for solving nonlinear equations. In that sense, the use of conformable derivatives has shown better behavior than fractional ones, not only in the theory, but also in the practice. In this work, we adapt the approximation of conformable derivatives in order to design the first conformable derivative-free iterative schemes to solve nonlinear equations: a Steffensen’s type method and a Secant type method; the latter with memory. Convergence analysis is made, preserving the order of classical cases, and the numerical performance is studied in order to confirm the results in the theory. It is shown that these methods can present some numerical advantages versus their classical partners, with wide sets of converging initial estimations.

In this paper, an iterative procedure to find the solution of a nonlinear structural model is introduced. The model presents different multiplicities where parameters are randomly selected within a solvability region. To achieve this aim, a class of multipoint fixed-point iterative schemes for single roots is modified to find multiple roots, reaching the fourth order of convergence. Complex discrete dynamics techniques are employed to select the members with the most stable performance. The structural problem, as well as some academic problems involving multiple roots, are solved numerically to verify the theoretical analysis, robustness and applicability of the proposed scheme.

The near-infrared (NIR) organic dyes with strong ultrafast nonlinear optical (NLO) activities are of importance for various applications. However, such kinds of dyes are still scarce. In this work, we have compared the NLO properties of two NIR Aza-BODIPY derivatives, in which the strong electron-donating groups, namely 4-(N, N-dimethylamino) phenyl and 1-ethyl-1,2,3,4-tetrahydroquinoline groups, are connected with the cores of Aza-BODIPY. Z-Scan experimental results show that two Aza-BODIPY derivatives exhibit strong saturation absorption and large modulation depth under the excitation of femtosecond pulses at 800 nm. Under 1300 nm excitation, two derivatives exhibit strong nonlinear refraction. In addition, the Aza-BODIPY derivatives also display effective two-photon excited fluorescence emission in the wavelength range of 1200-1600 nm. Based on the experimental results, it is found that 1-ethyl-1,2,3,4-tetrahydroquinoline group can more effectively enhance the NLO properties of Aza-BODIPY derivatives compared with the 4-(N, N-dimethylamino) phenyl group, thus providing new possibilities for the design and development of NIR NLO materials.

The concepts of fractional calculus and the related techniques have been gaining momentum in circuit system fields, and an increasing body of evidence suggests that fractional-order characteristics are widely distributed in electronic components. In this paper, we consider the fractional characteristics of non-solid aluminum electrolytic capacitors and focus on the nonlinear dynamic characteristics of peak-current-mode controlled (PCMC) dc-dc boost converters with such components. In the work, we establish a piecewise smooth non-commensurate fractional-order model to describe the converter, in which the fractional-order equivalent impedance model of capacitors is adopted and the detailed control loop is considered. In order to analyze the converter, we use the fractional Adams-Bashforth-Moulton typed method (F-ABM) and stroboscopic map technique to obtain the time-domain solutions and the bifurcation diagram. The results of bifurcation diagrams indicate that, with the change of different parameters, the converter enters chaotic state through period doubling bifurcation. In order to provide empirical evidence for the nonlinear dynamic analysis, we consider both circuit-level simulation and experiments in the work, the results of which further confirm the results of theoretical analysis.

Spherically symmetric solution in 4D Einstein--Gauss--Bonnet gravity coupled to modified logarithmic nonlinear electrodynamics (ModLogNED) is found. This solution at infinity possesses the charged black hole Reissner--Nordstr\"{o}m behavior. We study the black hole thermodynamics, entropy, shadow, energy emission rate and quasinormal modes. It was shown that black holes can possess the phase transitions and at some range of event horizon radii black holes are stable. The entropy has the logarithmic correction to the area law. The shadow radii were calculated for variety of parameters. We found that there is a peak of the black hole energy emission rate. The real and imaginary parts of the quasinormal modes frequencies were calculated. The energy conditions of ModLogNED are investigated.

In this paper, we study the weak deflection angle using Gauss-Bonnet theorem and bounding greybody factor for electric and magnetic black holes in the background of nonlinear electrodynamics. Using Gibbons and Werner's approach, first we acquire the Gaussian optical curvature to use in Gauss-Bonnet theorem and calculate the bending angle for spherically symmetric electric and magnetic black holes in both non-plasma and plasma mediums in the weak field limits. Later, we calculate the rigorous bounds of the greybody factor for the given black holes. Furthermore, we look into the graphical behaviour of bending angles and greybody bounds at some specific values of multiple parameters as well as black holes charges. It is to be mention here that all the results for the electric and magnetic charged black holes solutions reduce into the Schwarzschild black hole solution in the absence of the black holes charges.

The widespread integration and growing dependence among currency, stock and commodity markets make these markets often very vulnerable to shocks and at risk of collapse at the same time. As a result, these trends threaten the sustainability of the entire financial system. In this study, we explore the spillovers and nonlinear dependences between the seven major foreign ex-change rates, crude oil and gold prices, a global stock price index, and oil and stock implied volatility indices as proxy variables for global risk factors by em-ploying directional spillover network approach. We also use multi-scale de-composition method and nonlinear causality test between these variables to capture multi-level relationships at short and long horizons. Major findings are summarized as follows. First, from the multi-scale decomposition analysis, we identify that Granger causality test results and the direction and strength of return spillovers change with the level of decomposition. Second, the results of nonlinear causality tests show variation in both the significance and direction of Granger causality relationships between the decomposed currency and other series at different timescales, especially for the decomposed oil, gold, and OVX series. Third, the measured directional spillover indices identify the EUR as the largest contributor of connectedness to the other series. The central role of the EUR is a net transmitter of connectedness to gold, oil, the GBP, JPY, and CHF.

Since December 2019, the coronavirus disease (COVID-19) has rapidly spread worldwide. The Mexican government has implemented public safety measures to minimize the spread of the virus. In this paper, the authors use statistical models in two stages to estimate the total number of coronavirus (COVID-19) cases per day at the state and national level in Mexico. Two types of models are proposed: first, a polynomial model of the growth for the first part of the outbreak until the inflection point of the pandemic curve and then a second nonlinear growth model is used to estimate the middle and the end of the outbreak. Model selection will be performed using Vuong’s test. The proposed models show overall fit similar to predictive models (e.g. time series, and machine learning); however, the interpretation of parameters is less complex for decision-makers and the residuals follow the expected distribution when fitting the models without autocorrelation being an issue.

In a bid to resolve lingering problems in cosmology, more focus is being tilted towards cosmological models in which physical constants of nature are not necessarily real constants, but varying with cosmic time. In this paper we have study cosmology in nonlinear electrodynamics with the Newton's gravitational constant $G$ not a constant but vary in form of power-law of the scale factor of the universe. The evolution of the scale factor $a (t)$ is studied in this model which depends on nonlinear electrodynamics fine tuning term of $\alpha$. Then we check the stability of the model using the speed of sound.

The logarithmic correction to Bekenshtein$-$Hawking entropy in the framework of 4D Einstein - Gauss - Bonnet gravity coupled with nonlinear electrodynamics is obtained. We explore the black hole solution with the spherically symmetric metric. The logarithmic term in the entropy has a structure similar to the entropy correction in the semi-classical Einstein equations which mimics the quantum correction to the area low. The energy emission rate of black holes and energy conditions are studied. The quasinormal modes of a test scalar field are investigated. The gravitational lensing of light around BHs was studied. We calculated the deflection angle for some model parameters.

Not only does this paper present a novel type-2 fuzzy system for identification and behavior prognostication of an experimental solar cell set and a wind turbine, but also it brings forward an exquisite technique to acquire an optimal number of membership functions and the corresponding rules. It proposes a seven-layered NCPRT2FS. For fuzzification in the first two layers, Gaussian type-2 fuzzy membership functions with uncertainty in the mean, are exploited. The third layer comprises rule definition and the forth one embeds fulfillment of type reduction. The three last remained layers are the ones in which resultant left–right firing points, two end-points and output all get assessed correspondingly. It should not be neglected off the nutshell that recurrent feedback at the fifth layer exerts delayed outputs ameliorating efficiency of the suggested NCPRT2FS. Later in the paper, a modern structural learning, established on type-2 fuzzy clustering, is held forth. An adaptively rated learning back-propagation algorithm is extended to adjust the parameters ensuring the convergence as well. Eventually, solar cell photo-voltaic and wind turbine are deemed as case studies. The experimental data are exploited and the consequent yields emerge so persuasive.

We report enhanced nonlinear optics in complementary metal-oxide-semiconductor (CMOS) compatible photonic platforms through the use of layered two-dimensional (2D) graphene oxide (GO) films. We integrate GO films with silicon-on-insulator nanowires (SOI), high index doped silica glass (Hydex) and silicon nitride (SiN) waveguides and ring resonators, to demonstrate an enhanced optical nonlinearity including Kerr nonlinearity and four-wave mixing (FWM). The GO films are integrated using a large-area, transfer-free, layer-by-layer method while the film placement and size are controlled by photolithography. In SOI nanowires we observe a dramatic enhancement in both the Kerr nonlinearity and nonlinear figure of merit (FOM) due to the highly nonlinear GO films. Self-phase modulation (SPM) measurements show significant spectral broadening enhancement for SOI nanowires coated with patterned films of GO. The dependence of GO’s Kerr nonlinearity on layer number and pulse energy shows trends of the layered GO films from 2D to quasi bulk-like behavior. The nonlinear parameter of GO coated SOI nanowires is increased 16 folds, with the nonlinear FOM increasing over 20 times to FOM > 5. We also observe an improved FWM efficiency in SiN waveguides integrated with 2D layered GO films. FWM measurements for samples with different numbers of GO layers and at different pump powers are performed, achieving up to ≈7.3 dB conversion efficiency (CE) enhancement for a uniformly coated device with 1 layer of GO and ≈9.1 dB for a patterned device with 5 layers of GO. These results reveal the strong potential of GO films to improve the nonlinear optics of silicon, Hydex and SiN photonic devices.

An exact spherically symmetric and magnetically charged black hole solution in 4D Einstein-Gauss-Bonnet gravity coupled to nonlinear electrodynamics (NED) is obtained. The NED Lagrangian is given by ${\cal L}_{NED} = -{\cal F}/(1+\sqrt[4]{2\beta{\cal F}})$, where ${\cal F}$ is the field invariant. We study the thermodynamics calculating the Hawking temperature and the heat capacity of the black hole. The phase transitions take place when the Hawking temperature has an extremum and the heat capacity is singular. We demonstrate that black holes are thermodynamically stable in some range of event horizon radii where the heat capacity is positive. The BH shadow radii are calculated. It is shown that when increasing the nonlinearity parameter $\beta$ the BH shadow radius is decreased.

Abstract: The article proposes to consider the possibility of connecting the problems of engineering synthesis of frequency control systems for asynchronous electric drives with the basic provisions of the theory of identification of asynchronous electric motors based on the equations of a generalized AC electric machine.The article presents the results of experimental studies of load parrying processes in asynchronous electric drives with vector and scalar controls. These results indicate the absence of fundamental advantages as processes in a drive with vector control. This advantage should have manifested itself in a more efficient formation of the moment and fast transients. It is suggested that the reason for this is in too significant errors, assumptions and simplifications of the equations adopted in the derivation of vector control and which are its theoretical basis. A method is proposed for describing asynchronous electric motors by nonlinear transfer functions, which made it possible to formulate the principle of correction of electric drives and a method for assessing their efficiency.The article shows. that the correction based on the proposed nonlinear transfer functions of the induction motor is much more efficient than the traditional vector control, which was confirmed by detailed experiments and modeling. The results of the most important of which are given in the article. An assumption was made. that the advantage in efficiency is due to a more accurate identification of the dynamics of an asynchronous electric motor with a gear function instead of vector equations.

This study suggests a novel cooperative multi-simplex algorithm that generalizes a local search optimizer to design a novel global search heuristic algorithm. The proposed algorithm exploits the vertex sharing strategy to enhance the search abilities of the working simplexes. The vertex sharing among the simplexes is carried out through cooperative step that is based on fitness of the underlying simplex. The proposed algorithm is applied to solve some systems of nonlinear equations by transforming them to optimization problems. Comparative analysis of results shows that the proposed method is practical and effective.

Quantum loops are processes that constitute quantum objects. In the causal model of quantum loops and quantum objects presented here, the nonlinear processes involve the elementary units of spacetime and the associated elementary units of quantum fields. As such, quantum loop processes are the sources of gravitational fields (i.e., spacetime curvature) and of the quantum objects wave function. The model may be viewed as a derivative of loop quantum gravity, spin networks and causal dynamical triangulation, although significant deviations to these theories exist. The causal model of quantum loops is based on a causal model of spacetime dynamics where space(-time) consists of interconnected space points, each of which is connected to a small number of neighboring space points. The curvature of spacetime is expressed by the density of these space points and by the arrangement of the connections between them. The quantum loop emerges in a nonlinear collective behavioral process from a collection of space points that carry energy and quantum field attributes.

The article analyzes Bernoulli 's binary sequences in representation of empirical events about the distribution of natural resources and population sizes. Considering the event as a nonlinear system, and consisting of two dependent random variables, with memory and probabilities in maximum finite or infinite lengths, constant and equal to ½ for both variables (stationary process). The expressions of the possible trajectories remain constant in sequences that are repeated alternating the presence or absence of one of the variables at each iteration (asymmetric). There are constant oscillations in the event except if the variables X₁ and X₂ are regulated as a function of time Y. It is observed that the variables X₁ and X₂ assume in time T_k → ∞ specific behaviors (geometric variable) that can be used as management tools for random systems. In this way, the article seeks to know from this analyzes, the maximum entropy of information in the system by a theoretical view and how to model resources distribution or containment in the given problem.

In this paper, we consider a fourth-order suspension bridge equation with nonlinear damping term |u_t|^m-2u_t and source term |u|^p-2u. We give necessary and sufficient condition for global existence and energy decay results without considering the relation between m and p. Moreover, when p>m, we give sufficient condition for finite time blow-up of solutions. The lower bound of the blow-up time T_max is also established. It worth to mention that our obtained results extend the recent results of Wang (J. Math. Anal. Appl., 2014) to the nonlinear damping case.

Stability studies remain a crucial aspect of power systems dynamic analysis, and are typically explored in three main categories: numerical methods, linearization techniques, or direct methods, which utilize Lyapunov energy functions. This paper belongs to the third category, and highlights the usefulness of the Popov stability criterion in the analysis of nonlinear power system models. The main advantage of this criterion is that it provides conditions for global asymptotic stability of an equilibrium point, for a nonlinear dynamic system. We show a general method to apply this stability criterion, and examine its uses in several specific applications and case-studies. The results are demonstrated by analyzing the stability of a system that includes a grid-connected storage device and a renewable energy source.

At the beginning of any electric arc welding process, a regime called transient regime will always occur, characterized by the continuous variation of the energy flow, also resulting in the variation of the cooling rate of the welded joint. Consequently, the weld bead hardness varies from a maximum value to an approximately constant value, and this phenomenon can be represented by an asymptotic exponential function. For several welded specimens, it would be possible to fit a non-linear regression for each specimen, however, it would be a difficult task to combine different regressions in a single analysis. The objective of this study is to evaluate the applicability of mixed-effects models and artificial neural networks to predict the longitudinal hardness of the weld bead in the initial transient regime. To this end, linearized and nonlinear mixed-effects models and artificial neural networks with different architectures were fitted. Finally, valid models were obtained with all approaches, with artificial neural network model slightly better fitted. However, the explainability capacity of the linearized mixed-effects model was superior, showing that the relative thickness, one of the predictor variables, was responsible for 48% of the variation in longitudinal hardness of weld bead.

The Planetary Roller Screw Mechanisms (PRSMs), alongside Ball Screw Mechanisms (BSMs) and Electromechanical Actuators (EMAs), occupies a pivotal role in advancing the precision and efficiency of various industrial applications, including aerospace, automotive, and high-precision machining tools. Despite their critical advantages such as high load capacity, superior precision, and extended lifespan, the deployment of PRSMs in complex operational conditions reveals a landscape rife with challenges and opportunities for further research. This comprehensive review endeavors to dissect the multifaceted aspects of PRSMs, focusing on their mechanics and dynamics, tribology and thermal behavior, and the paramount importance of reliability and condition monitoring. By synthesizing current research findings, this paper highlights the significant advancements in understanding the static and dynamic characteristics of PRSMs, the intricate interplay between lubrication conditions and wear mechanisms, and the critical role of thermal effects on operational performance. Moreover, it delves into the dynamic models that address the impact of manufacturing imperfections, such as waviness and defects, on the reliability of these mechanisms. Despite the strides made, the review identifies critical gaps in the existing literature, particularly under conditions of extreme temperatures, large deformations, and multifaceted loads, advocating for a holistic approach to research. By proposing integrated thermo-mechanical models and emphasizing the need for empirical validations, this paper outlines a roadmap for future studies aimed at facilitating the development of more robust and reliable PRSMs, capable of meeting the demands of complex operational scenarios and advancing the field of high-precision applications in aerospace, robotics, and beyond.

To identify the exchange coefficients of a nonlinear polynomial tricompartmental general system of α+β , we follow the procedure; firstly, the recommended solution is to introduce an adequate time t*&gt;0 in a determinable manner. That is, after injecting quantity a into the main compartment, wait a moment for the exchange in the polynomial α+β order nonlinear general system to settle, and then compare this compartment to compartment 2 at t*. Secondly, applying the Taylor formula will linearize the system and identify the exchange coefficients. Finally, we will prove that the linearization method is stable.

The investigation of plasma channels induced by focused ultra-short 1030-nm laser pulses in bulk of synthetic HPHT diamond revealed strong dependence of their size and shape on the used numerical aperture of the lens (NA=0.15-0.45). It was shown that at loose focusing conditions, it is possible to significantly increase the length of the plasma channel with a slight increase in pulse power, while tight focusing allows to obtain more compact structures in the same range of used powers. Such dependence paves the way to new possibilities in 3D processing of transparent dielectrics, allowing, for example, to vary the spatial parameters of modified regions without changing the setup, but only by controlling the lens aperture, which seems very promising for industrial applications.