This study characterizes the microstructure and its associated crystallographic features of bulk maraging steels fabricated by selective laser melting (SLM) combined with a powder bed technique. The fabricated sample exhibited characteristic melt pools in which the regions had locally melted and rapidly solidified. A major part of these melt pools corresponded with the ferrite (alpha) matrix, which exhibited a lath martensite structure with a high density of dislocations. A number of fine retained austenite (gamma) with a <001> orientation along the build direction was often localized around the melt pool boundaries. The orientation relationship of these fine gamma grains with respect to the adjacent alpha grains in the martensite structure was (111) gamma // (011) alpha and [-101] gamma // [-1-11] apha (Kurdjumov–Sachs orientation relationship). Using the obtained results, we inferred the microstructure development of maraging steels during the SLM process. The results depict that new and diverse high-strength materials can be used to develop industrial molds and dies.

Electric arc furnace oxidizing slag (EAF) has a high density of 3.0~3.7 t/m3 and therefore has a high bulk density when mixed with concrete. Extensive research has been conducted on the use of concrete with high unit volume weight as heavyweight concrete for radiation shielding concrete. In this study, to examine the possibility of developing a radiation shielding concrete, the physical properties of normal concrete, magnetite concrete, EAF concrete, and EAF concrete with added iron powder, were compared. Also, their radiation shielding performance was assessed through shielding tests against X-rays and γ-rays. While the unit volume weight of EAF concrete (3.21 t/m3) appeared lower than that of magnetite concrete (3.5 t/m3), the compressive strength of EAF concrete was greater than those of magnetite and normal concretes. The radiation shielding ratio of magnetite concrete was observed to be 93.9% from the X-ray shielding test, followed by 91.2% of EAF concrete, and 73.7% of normal concrete, indicating a linear relationship with unit volume weight. From the γ-ray shielding test, the performance of EAF and magnetite concretes appeared to be similar. Based on the excellent physical properties and radiation shielding performance of EAF concrete, its potential applicability as radiation shielding concrete was confirmed.

This study deals with the turning of AISI O2 steel, which has high machinability and dimensional stability in heat treatment and is used in the manufacture of many machine elements, with cryogenically treated and untreated and coated and uncoated cutting tools. In the first phase of the study, along with the determined cutting parameters, Fc and Ra output parameters were also optimized using the RSM method. In addition, numerical significance was obtained with ANOVA analysis, and estimated values were calculated by preparing regression equations. In the second phase, the wear performance of cutting tool tips with and without deep cryogenic treatment was explained with the support of SEM images, EDX, XRD, and microhardness analyses. Feed (F) was found to be the most influential parameter on Fc at 78.89%. The lowest optimized Fc value found with the RSM method was 339.99 N. In order to obtain this value, Vc 252.525 m/min and F 0.16 mm/rev should be selected. In addition, CVD-coated and cryogenic heat-treated cutting tools should be preferred for ideal Fc. It was shown that the most effective parameter on Ra was F, with 69.38%. For both heat treatment and coating conditions, Ra increased significantly as the feed rate increased. In the case of selecting Vc as 243.434 m/min and F as 0.16 mm/rev, the smallest Ra value optimized with the RSM method is 1.04 μm. In addition, a cutting tool without coating and cryogenic heat treatment is also needed for ideal Ra. According to the results of the analysis confirming the effect of deep cryogenic heat treatment on the wear performance of cutting tools in the second stage, coated and uncoated cutting tools had at least 16% longer life compared to the others.

In this paper, polyurethane concrete (PUC) is used as wire embedding material to form a new polyurethane concrete- prestressed steel wire (PUC-PSW) reinforcement method. The lightweight and high-strength PUC materials not only bond and anchor the prestressed steel wire (PSW), but also passively participate in the structural force. The problems caused by using mortar or composite mortar as the embedding material are avoided. Twelve reinforced concrete T-beams were tested for PUC-PSW flexural reinforcement. It consists of 1 unreinforced beam, 4 PSW reinforced beams, and 7 PUC-PSW reinforced beams. The wire embedding material, wire anchorage form, PUC material depth, amount of wire, and loading type were used as variables. The test results show that PUC-PSW reinforcement can obviously enhance the flexural load and ultimate load of the reinforced beams compared with PSW reinforcement. The ability of PUC-PSW reinforcement to limit crack development is better than that of PSW reinforcement beam, especially after the main beam steel yield. The strength, stiffness and crack limiting ability of the reinforced beam increase with the PUC thickness of the reinforced layer.

Methylene blue has been electropolymerized on the surface of a stainless steel 316. The addition of sodium oxalate and working at a pH near 11 has allowed to obtain steel electrodes coated with electroactive polymer. This polymer shows electrochromic properties similar to those of the monomer, but also appears electroactivity at more positive potentials which is associated to the active centers in the bridges between monomeric units. The study by means of digital video electrochemistry has allowed on the one hand, to quantify the color changes on the entire surface of the stainless steel simultaneously and by means of the mean color intensities to separate the contribution to the overall polymer response of the active centers of the phenothiazine ring and of the inter-monomer bonds. A reduction mechanism for the polymer compatible with the pH variation of the observed electrochemical behavior is proposed.

The energy transition is a challenge that affects all sectors, from transport to civil structures and industry. In the industrial sector, the greatest need is the decarbonisation of energy-intensive in-dustries, such as producers of iron and steel, aluminum, cement, petrochemicals, paper, and more. The steel industry, in particular, is a hard-to-abate high-emissivity industry that, due to chemical processes and high thermal demands (often above 500 °C), contributed to 7.4% of global CO2 emissions in 2021. This paper explores the potential applications of hydrogen in these hard-to-abate sectors, highlighting its versatility and significance in decarbonization efforts, especially as a me-dium to facilitate the transition to green electric energy uses. It provides an overview of hydrogen production methods, emphasizing the importance of sustainable and green hydrogen production. It reviews hydrogen production methods, storage, and potential in blended combustion. In the final part of the article, some considerations are introduced on the possible role of hydrogen in the steel sector (both as a supplementary fuel and as a reducing agent in innovative processes), showing that while there is potential for its inclusion as an element for decarbonization, it is necessary to carefully evaluate the energy balances of the various processes and the methods of hydrogen production, in order to avoid achieving only marginal effects.

Digital twins are an emerging technology that could be harnessed for the digitalization of the industry. Steel industry systems contain a large number of electro-hydraulic components, as proportional valves. An input-output model for a novel water proportional cartridge valve is derived from physical modelling based on fluid mechanics, dynamics, and electrical principles. The valve is a two-stage valve with two 2/2-way water proportional valves as the pilot stage and a marginally stable poppet-type cartridge valve as the main valve. The orifice equation, which is based on Bernoulli principles, is approximated by a polynomial which makes parameter estimation easier and makes modelling possible without measuring pressure of the varying control volume situated in the pilot stage part of the valve. Data were collected when the valve was operating as a component in a closed-loop system as part of a press-mill machine in a steel manufacturing plant. Parameter estimation was made by convex optimization with physical constraints to overcome problems caused by poor system excitation. For comparison, a simple linear model was derived and the least squares method used for parameter estimation. A thorough estimation of the parameters relative errors is presented. The model contains 5 parameters related to the design parameters of the valve. The modelled position output is in good agreement with experimental data for training and test data. The model can be used for real time monitoring of the valve’s status by the model parameters. One of the model parameters varies linearly with production cycles. Thus, aging of the valve can be monitored.

This paper presents laboratory devices on which experimental measurements were carried out to prove the validity of the assumption about the reduction of vibrations transmitted to the conveyor belt structure generated by the impact forces of falling material grains in the places of transfer or on the hoppers of conveyor belts. In order to limit damage to the conveyor belts caused by the impact of the sharp edges of material grains, conveyor belts are supported by impact rollers or impact rubber rods in the places of transfers and on the hoppers of belt conveyors. The flattened ends of the impact rollers are inserted into the grooves of steel brackets installed on the supports of the fixed conveyor idlers of a conventional design. In this paper, a special modification of the fixed conveyor idler is presented, which consists of inserting plastic brackets into the structurally modified roller axle holders of the fixed conveyor idler. Measurements were carried out on the first laboratory device, which showed that the specially modified fixed conveyor idler resulted in a higher damping of up to 15% of the impact forces of the falling weight on the rubberized hoop of the impact roller shell compared to the conventional fixed conveyor idler design. Measurements carried out on the second laboratory device show that the effective vibration velocity values detected at the points where the impact roller axis fits into the fixed roller table holder, i.e. points B and D, are higher than when using plastic brackets, up to 6% for a 108 mm diameter roller, compared to steel impact roller brackets.

Many bio-applicable materials, medical devices, and prosthetics combine both polymer and metal components to benefit from their complementary properties. This goal is normally achieved by their mechanical bonding or casting only. Here, we report an alternative easy method for the chemical grafting of a polymer on the surfaces of a metal or metal alloys using alkoxy amine salt as a coupling agent. The surface morphology of the created composites was studied by various microscopy methods, and their surface area and porosity were determined by adsorption/desorption nitrogen isotherms. The surface chemical composition was also examined by various spectroscopy techniques and electrokinetic analysis. Elements distribution on the surface was determined and successful bonding of the metal/alloys on one side with the polymer on the other one was confirmed by alkoxy amine. The composites show significantly increased wettability, reliable chemical stability of the bonding, excellent bacterial anti-adhesive properties and functionality, i.e. the characteristics promising for their application in biomedical field.

Stochastic modelling of geometrically imperfect steel frame structures requires inputs of statistical values of the imperfection parameters, in some cases also with suitably selected mutual correlations between these input parameters. The paper presents a verification study of two stochastic methods to directly model the initial global geometrical imperfections of the steel frame structures. The stochastic input values of geometrical imperfections are derived from the tolerance criteria of the corresponding European Standard. Two advanced stochastic methods have been developed, referred as #RSS (random story sway) and #RSP (random story position). These methods are verified using random sampling simulations. This study provides useful provisions for the advanced numerical analyses of multi-story steel frames of various geometries. The proposed methods are verified for equidistant story heights and for structures of up to 24 stories, hence might be used for the most types of the standard steel frame structures.

Advanced high-strength steels (AHSS) have a wide range of applications in equipment safety and lightweight design, and enhancing the strength of AHSS to the ultra-high level of 2 GPa is currently a key focus. In this study, a new process of thermo-mechanical control process followed by direct quenching and partitioning (TMCP-DQP) is developed based on Fe-0.4C-1Mn-0.6Si (wt.%) low-alloy steel, and the effects of microstructure evolution on mechanical properties under TMCP-DQP process and conventional hot rolled quenched and tempered process (HR-QT) are comparatively studied. The results show that the TMCP-DQP process not only shortened the processing steps but also achieved outstanding comprehensive mechanical properties. The TMCP-DQP steel exhibits a tensile strength of 2.23 GPa, accompanied by 11.9% elongation and a Brinell hardness of 624 HBW, with an impact toughness of 28.5 J at -20 ℃. In contrast, the HR-QT steel exhibits tensile strengths ranging from 2.16 GPa to 1.7 GPa and elongations between 5.2% and 12.2%. The microstructure of TMCP-DQP steel primarily consists of lath martensite, containing thin-film retained austenite (RA), nanoscale rod-shaped carbides, and a minor number of nanoscale twins. The volume fraction of RA reaches 7.7%, with an average carbon content of 7.1 at.% measured by three-dimensional atom probe tomography (3DAP). Compared to the HR-QT process, the TMCP-DQP process results in finer microstructure, with a prior austenite grain (PAG) size of 11.91 μm, forming packets and blocks with widths of 5.12 μm and 1.63 μm. The TMCP-DQP process achieves the ultra-high strength of low-alloy steel through the synergistic effects of grain refinement, dislocation strengthening, and precipitation strengthening. The dynamic partitioning stage stabilizes the RA through carbon enrichment, while the relaxation stage reduces a small portion of the dislocations generated by thermal deformation, and the self-tempering stage eliminates internal stresses, all guaranteeing considerable ductility and toughness. The TMCP-DQP process may offer a means for industries to streamline their manufacturing processes and provide a technological reference for producing 2.2 GPa grade AHSS.

This study presents a combined electrochemical impedance spectroscopy (EIS) and atomic force microscopy (AFM) and Scanning Kelvin Probe Force Microscopy(SKPFM) investigation on the natural passivation process of stainless steels (AISI 316 and AISI 304) and nickel-based alloy (INCONEL 600) as a function of immersion time in an alkaline medium (pH = 13). EIS measurements show an increase in the resistance of the film with increasing immersion time in the electrolyte. After 3 days of immersion, for the three alloys, the films formed constitute an effective barrier to the dissolution of the alloys as shown by AFM and SKPFM. The oxide film growth on each substrates is only influenced by trenches formed during the polishing step and don’t depend on the chemical composition.

In metal continuous casting process is important to estimate the temperature evolution of casted section along machine from meniscus (point in which liquid metal is poured) to cutting machine where product is cut at commercial length. Particularly in the case of large sections, a convenient approximated model to achieve this goal with a feasible computational effort, is the so called travelling slice: the transversal section of casted product is subjected to different thermal boundary conditions (e.g. thermal flux, radiation, convection) that are found during the movement at constant speed from meniscus to the end of machine. In the case of an axisymmetric section, a comparison with the exact solution can be easily achieved. The article will show pros and cons of both, namely the far lower computational cost of travelling slice model without losing precision. Results confirm the validity of the travelling slice approach also at low casting speed and huge dimensions.

Improper lifting measures of long-span spatial steel structures during construction process may delay the construction period and even cause safety accidents. Few studies on long-span spatial steel structures considered time-varying mechanical characteristic during construction process. In order to achieve safe and efficient installation in a long-span spatial steel structure, this research presents a time-varying mechanical analysis of the synchronous and asynchronous integral lifting and a single and interlaced point’s asynchronous integral lifting analysis method of a long-span spatial steel structure. The results showed that in the case of asynchronous lifting of single point, the displacement influence on other members is related to the distance. The closer the distance from the lifting point, the greater the influence. In asynchronous integral lifting, the lifting point with large lifting force is first installed to the specified position, and the lifting point with small lifting force is installed to the specified position.

To achieve the required mechanical properties in the heat treatment of steel, it is necessary to have an adequate cooling rate and to achieve the desired final temperature of the product. This should be achieved with one cooling unit for different product sizes. In order to provide high variability of the cooling system, different types of nozzles are used in modern cooling systems. Designers often use simplified, inaccurate correlations to predict the heat transfer coefficient, resulting in oversizing of the designed cooling or failure to provide the required cooling regime. This typically results in longer commissioning times and higher manufacturing costs of the new cooling system. Accurate information about the required cooling regime and the heat transfer coefficient of the designed cooling is critical. This paper presents a design approach based on laboratory measurements. Firstly, the way to find or validate the required cooling regime is presented. The paper then focuses on nozzle selection and presents laboratory measurements that provide accurate heat transfer coefficients as a function of position and surface temperature for different cooling configurations. Numerical simulations using the measured heat transfer coefficients allow the optimum design to be found for different product sizes.

Aiming to diminish the defects caused by high-speed pulsed GMAW welding, such as non-penetration, non-fusion, humping and undercut, the paper proposed an improved twin-wire double-pulsed high-speed welding process by introducing the impact of additional shielding gas on the welding pool and the effects of different shielding gas flowrates on the microstructure and mechanical properties of the welded seam was investigated. The 2205 duplex stainless steel plate was used as the base material for the butt welding test, and the welded seams were subjected to tensile test, metallographic analysis, hardness analysis, and nondestructive testing. The results indicate that as the flowrate of additional shielding gas increases in the range of 8 L/min~16 L/min, the width of the welded seam increases and the height of reinforcement decreases gradually. However, a grooved seam with a lower middle region and higher sides will appear when the gas flowrate becomes excessively large. The test results indicate that the jet impact force is relatively moderate when the flowrate of the additional shielding gas is 12 L/min and thus, is optimal for the welded seam.

Features of nanosecond discharge development in a non-uniform electric field are studied experimentally. High spatial resolution imaging showed that thin luminous tracks of great length with a cross-section of a few microns are observed against the background of discharge glow in air and argon. It has been established that the detected tracks are adjacent to brightly luminous white spots on the electrodes or to the vicinity of these spots, and are associated with the flight of small particles. It is shown that the traces have various shapes and change from pulse to pulse. The particle tracks may look like curvy or straight lines. In some photos, they can change the direction of movement to the opposite. The particle trace was found to abruptly cut off and a bright flash is visible at the trail break point. The color of the tracks differs from that of the spark leaders, while the bands of the second positive nitrogen system dominate in the gap spectra during the existence of a diffuse discharge. Areas of blue light are evident near the electrodes, as well. Development of glow in the gap during its breakdown is revealed using an ICCD camera. Physical reasons for the observed phenomena are discussed.

The literature has well established prestressing in concrete beams and its calculation procedures. However, its use in composite steel-concrete beams has increased despite main normative codes lacking a specific approach for it. Designers must, in most cases, combine the available criteria to calculate the standards of steel and reinforced concrete structures. This study aimed to formulate this optimization problem and analyze CO2 emissions for the optimal design of composite steel-concrete beams with external prestressing. The design variables for the optimization problem include cross-section of laminated or welded profiles, slab height, characteristic strength of concrete to compression, and number of tendons. We obtained a solution for the optimization problem via a genetic algorithm (GA) and a particle swarm optimization one (PSO). Comparative analysis with experimental example and with optimization problem of prestressed steel beam are performed. An parametric analysis to several spams is performed, which enabled to evaluate the factors that most impact CO2 emissions. According to results, the chosen algorithms effectively obtained solutions for the problem, and PSO usually provided better results than GA. Regarding the final solution composition, steel contributes the most to emissions, welded profiles provided better solutions than laminated ones, and laminated spans of up to 17.5m and welded ones up to 27.5m dispensed with tendons.

In the field of metallurgy, there are many factors that influence the final quality of cast iron. These are mainly charge materials, chemical composition, metallurgical preparation up to the final casting process. Even small deviations from metallurgical processing lead to fluctuations in melt quality and the occurrence of casting defects. Charge materials has a significant impact on the quality of cast iron, especially steel scrap, which is increasingly used from an economic and ecological point of view, especially when melting cast iron in electric furnaces. Cast iron produced from a higher proportion of steel scrap in the charge has higher hardness and tensile strength. On the other side, these cast irons has a higher tendency to chillout, brittleness, shrinkage, pearlitic microstructure, stresses and higher purity due to the difference in hardness at different wall thicknesses of the castings. It is the high hardness that is the problem in the final machining of castings. These negative properties are recorded mainly in heavy thick-walled castings with higher tensile strength and hardness. This negative effect is mainly due to the nitrogen content in the steel scrap. Based on these knowledges, operating melts were realized in the foundry's operating conditions. The influence of steel scrap in the charge and the possibility of eliminating its negative effects on the properties of cast iron were investigated.

High-strength low-alloy steels (HSLAs) are widely used in the structural body components of many domestic motor vehicles owing to their better mechanical properties and greater resistance. The real production process of HSLA steelmaking can be regarded as a model that builds on the relationship between process parameters and product quality attributes. A surrogate modeling method is used, and the resulting production process model can be applied to predict the optimal manufacturing process parameters. We used different methods in this paper to build such a surrogate model, including linear regression, random forests, support vector regression, multilayer perception, and a simplified VGG model. We then applied three bio-inspired search algorithms, namely particle swarm optimization, the artificial bee colony algorithm, and the firefly algorithm, to search for the optimal controllable manufacturing process parameters. Through experiments on 9,000 test samples used for building the surrogate model, and 299 test samples for making the optimal process parameter selection, we found that the combination of a simplified VGG model and the firefly algorithm was the most successful at reaching a success rate of 100%—in other words, when the product quality attributes of all test samples satisfy the mechanical requirements of the end products.

In this study, the effect of hot stamping forming process on the properties change of compound layer in Al–Si coated high-strength steel sheet with different thickness was investigated. The coating layer in hot stamped high-strength steel sheet was composed of a diffusion layer and a compound layer. As the hot stamping temperature and holding time for forming increased, the thickness of the compound layer in the Al–Si coated high-strength steel sheet increased. The thickness of coating layer with the hot stamping for 500 sec at 890, 910 and 950 °C was obtained 8.9, 11.8, and 20.6 micrometer, respectively. The thickness of coating layer with hot stamping for 180, 500 and 550 sec at 910 ^oC was obtained 5.7, 11.8, and 17.8 micrometer, respectively. The compound layer in hot stamped high-strength steel sheet with Al–Si coating layer consists of Al_5.4Fe₂ and Fe₂Si phases. In the compound layer, Al and Si were irregularly distributed.

The main aim of this study is to investigate the optimization of the technological process for selective laser melting (SLM) additive manufacturing. The group of process parameters considered was selected from the first-stage parameters identified in preliminary research. Samples manufactured using three different sets of parameter values were subjected to static tensile and compression tests. The samples were also subjected to dynamic Split–Hopkinson tests. To verify the microstructural changes after the dynamic tests, microstructural analyses were conducted. Additionally, the element deformation during the tensile tests was analyzed using digital image correlation (DIC). To analyze the influence of the selected parameters and verify the layered structure of the manufactured elements, sclerometer scratch hardness tests were carried out on each sample. Basing on the research results it was possible to observe the porosity growth mechanism and its influence on the material strength (including static and dynamic tests). Parameters modifications that caused 20% lower energy density, elongation of the elements during tensile testing decreased twice, which was strictly connected with porosity growth. An increase of energy density by almost three times caused a significant reduction of force fluctuations differences between both tested surfaces (parallel and perpendicular to the building platform) during sclerometer hardness testing. That kind of phenomenon had been taken into account in the microstructure investigations before and after dynamic testing where it had been spotted a positive impact on material deformations based on fused material grains formation after SLM processing.

There always exist steel cuttings, holes and cracks at the interfaces in the explosive composite plate. Multi-pass friction stir processing (M-FSP) is proposed in this research to optimize the interface microstructure and the interface connection for 1060Al/Q235 explosive composite plate. Results show that the microstructures of 1060Al after M-FSP are fine and uniform owing to the strong stirring effect and recrystallization. Micro-defects formed by the explosive welding can be repaired by the M-FSP. However, M-FSP can also form tunnel defects in the aluminum, especially when the passes are one and two. The melting block and the melting lump in the composite plates are easy to become source of crack. The shear strengths and the bending properties for the 1060Al/Q235 explosive composite plate after M-FSP are the best when the passes are three, with the tool rotation speed of 1200rpm and the forward speed of 60mm/min. The optimized interfaces for the explosive composite plate after M-FSP are mainly by the metallurgical bondings, with a certain thickness and are discontinuous. Therefore, the crack extension stress is the largest and the mechanical properties are the best.

This paper presents the microstructural and mechanical properties of low and medium carbon advanced high-strength forging steels developed based on the third generation advanced high-strength sheet steels, in conjunction with those of conventional high-strength forging steels. Hot-forging followed by an isothermal transformation process considerably improved the mechanical properties of the forging steels. The improvement mechanisms of the mechanical properties were summarized by relating to the matrix structure, the strain-induced transformation of metastable retained austenite and/or a mixture of martensite and austenite.

Reducing emissions from the iron and steel industry is essential to achieve the Paris climate goals. A new system to reduce the carbon footprint of steel production is proposed in this article by coupling hydrogen direct reduction of iron ore (H-DRI) and natural gas pyrolysis on liquid metal surface inside a bubble column reactor. If grid electricity from EU is used, the emissions would be 435 kg CO₂/tls without considering methane leakage from the extraction, storage and transport of natural gas. Solid carbon, produced as a by-product of natural gas decomposition, finds applications in many industrial sectors, including as a replacement for coal in coke ovens. Specific energy consumption (SEC) of the proposed system is approximately 6.3 MWh per ton of liquid steel(tls). It is higher than other competing technologies, 3.48 MWh/tls for water electrolysis based DRI, and, 4.3-4.5 MWh/tls for natural gas based DRI and blast furnace-basic oxygen furnace (BF-BOF) respectively. Utilization of large quantities of natural gas, where the carbon remains unused, is the major reason for high SEC. Preliminary analysis of the system revealed that it has the potential to compete with existing technologies to produce CO₂ free steel, if renewable electricity is used. Further studies on the kinetics of the bubble column reactor, H-DRI shaft furnace, design and sizing of components, along with building of industrial prototypes are required to improve the understanding of the system performance.

The formability and failure behavior of TRIP steel blanks were investigated through various stress states. The forming limit diagram (FLD) at fracture is constructed both experimentally and numerically. Numerical studies are performed to evaluate the applicability of different damage criteria in predicting the FLD as well as complex cross-die deep drawing process. The fracture surface and numerical results revealed that the material failed in a different mode for different strain path. Therefore, Tresca model which is based on shear stress accurately predicted the conditions where shear had the profound effect on the damage initiation, whereas Situ localized necking criterion was able to calculate the conditions which localization was dominant.

The effect of filling velocity on positive macrosegregations in large size steel ingots was studied. Macrosegregation and macro-/micro-structure were characterized on the hot-tops and a portion of the upper section of two ingots. The measurements revealed that segregation features in the two ingots varied as a function of the alloying elements, and that the severity of positive macrosegregation in the casting body was reduced when the filling rate was increased. It was also found that at the higher filling rate, grain morphologies in the first solidified zones of the ingot changed from columnar to equiaxe, and secondary dendrite arm spacing (SDAS) became slightly smaller in the intermediate and final solidified zones. The experimental findings were analyzed in the framework of diffusion and convection controlled solidification, as well as liquid metal flow theories. The solute dependence of segregation features was related to the difference in solid-liquid partition coefficient and diffusion capability of each element in the liquid iron. Calculation of Reynolds numbers (Re) during the filling process, for both ingots, showed that higher filling velocity caused more instable movement of the liquid metal in the initial solidification stage, resulting in the modification of grain morphology, as well as accelerated solidification rate.

Ferrite body is the origin of crack and corrosion initiation of steels. Distribution and density of ferrite in seven steel ingots were examined by light optical microscopy and computational modeling in the study to explore the correlation of ferrite formation to chemical composition and mushy zone temperature in ingot forming. The central segregation phenomenon in ferrite distribution was observed in all the examined steel specimens except 0Cr17Ni4Cu4Nb stainless steel. No significant difference was found in distribution and density of ferrite amongst zones of the surface, ½ radius and core in neither risers nor tails of 0Cr17Ni4Cu4Nb ingots. Additionally, fewer ferrite was found in 0Cr17Ni4Cu4Nb compared to other examined steels. The difference of ferrite formation in 0Cr17Ni4Cu4Nb elicited a debate on the traditional models explicating ferrite formation. Considering the compelling advantages in mechanical strength, plasticity and corrosion resistance, further investigation on the unusual ferrite formation in 0Cr17Ni4Cu4Nb would help understand the mechanism to improve steel quality. In summary, we observed that ferrite formation in steel was correlated with mushy zone temperature. The advantages of 0Crl7Ni4Cu4Nb in corrosion resistance and mechanical stability could be resulted from that fewer ferrites formed and distributed in a scattered manner in microstructure of the steel.

In the current study, the failure behavior of retrofitted steel structures was studied experimentally and theoretically with steel/CFRP double strap joints (DSJs) under quasi-static tensile loading. A series of DSJs with different bonding lengths are also considered and examined to experimentally assess the effective bond length. To predict the failure load values of the tested specimens, a new stress-based criterion, namely the point stress (PS) criterion is proposed. Although some theoretical predictive modelling for the strength between steel/CFRP joints under various loading conditions has been presented, in this work by using the new proposed approach, one can calculate rapidly and conveniently the failure loads of the steel/CFRP specimens. Furthermore, to assess the validity of the new proposed criterion, further experimental data on steel/CFRP DSJs available in the open literature are predicted using the PS criterion. Finally, it was found that a good agreement exists between the experimental results and the theoretical predictions based on the PS criterion.

The corrosion inhibition effects of Drimia maritima (L.) Stearn sin. Urginea matima (L.) Backer on three different materials, i.e. as-cast Al-7 wt.% Si alloy, SAE 1020 low carbon steel and commercially pure Al samples, into a stagnant and naturally aerated 0.5 M NaCl solution are evaluated. For this purpose, both the potentiodynamic polarization curves and electrochemical impedance spectroscopy with equivalent circuit are utilized. It is found that inhibition effect in-creases up to certain minor Drimia maritima content. Adsorption isotherms (e.g. Langmuir and Temkin) have indicated that all three examined material comprise physical adsorption mecha-nism. Al-Si alloys have attained inhibition efficiency of about 96% at 25 oC with 1250 ppm of Drimia maritima, and ~43% with 625 ppm at 45 oC. On the other hand, the cp. Al and SAE 1020 samples attain ~ 89% and 68% with 1250 ppm and 500 ppm at 25 oC, respectively. This clearly in-dicates that the dosage of Drimia maritima green inhibitor into NaCl solution posses certain sus-ceptibility for each distinctive material examined. Impedance parameters obtained by using CNLS (complex non-linear least squares simulations) are correlated and discussed.

Governments worldwide are actively committed to achieving their carbon emission reduction targets, and one avenue under exploration is harnessing the potential of hydrogen. Blending hydrogen with natural gas is emerging as a promising strategy to reduce carbon emissions, as it burns cleanly without emitting carbon dioxide. This blending could significantly contribute to emissions reduction in both residential and commercial settings. However, a critical challenge associated with this approach is the potential for Hydrogen Embrittlement (HE), a phenomenon wherein the mechanical properties of pipe steels degrade due to the infiltration of hydrogen atoms into the metal lattice structure. This can result in sudden and sever failures when the steel is subjected to mechanical stress. To effectively implement hydrogen-natural gas blending, it is imperative to gain a comprehensive understanding of how hydrogen affects the integrity of pipe steel. This necessitates the development of robust experimental methodologies capable of monitoring the presence and impact of hydrogen within the microstructures of steel. Key techniques employed for this assessment include microscopic observation, hydrogen permeation tests, and tensile and fatigue testing. In this study, samples from two distinct types of pipeline steels used in the natural gas distribution network underwent rigorous examination. To induce hydrogen absorption, an electrochemical charging process is employed in a solution rich in H+ ions. This charging process, accomplished by a potentiostat applying a constant current, prompts the hydrogen evolution reaction at the steel specimen, acting as the cathode of the charging cell. Immediate tensile and fatigue testing following the charging process enables the evaluation of mechanical properties in comparison to non-charged samples. Different charging current densities are employed to simulate various hydrogen blend scenarios. The findings from this research indicate that charged samples exhibit a discernible decline in fatigue and tensile properties. This deterioration is attributed to embrittlement and reduced ductility stemming from the infiltration of hydrogen into the steel matrix. The extent of degradation in fatigue properties is correlated not only to the hydrogen content but also to the hydrogen permeability and diffusion rate influenced by steel’s microstructural features, with higher charging current densities indicating a more significant presence of hydrogen in the natural gas pipeline blend.

By using a two-stage physiologically based extraction test (PBET) and (W-PBET), the authors of this paper have estimated the bioaccessibility of metals (Pb and Fe) and their compounds in the GI tract of waterfowl and mammals. It has been shown that the metals (Pb and Fe) have low bioaccessibility; combined with the short time of shot exposition at the GI tract, this eliminates the risk of toxic effects in the case of shot ingestion by waterfowl. It has also been discovered that there is a significant difference in the bioaccessibility of metals and their compounds. A model was proposed and tested to predict the toxic effects of lead on biological objects depending on the threshold mass of consumption. This model takes into account data on the bioavailability of lead and regulatory values indicating dangerous concentrations of lead.

The energy transition is a challenge that affects all sectors, from transport to civil structures and industry. With reference to the industrial sector, the greatest need is the decarbonisation of industries energy-intensive, such as producers of iron and steel, aluminium, cement, petrochemicals, paper, etc. In particular, the steel industry is a hard to abate high-emissivity industry which due to chemical processes and high thermal demands (often above 500 °C) contributed to 7.4% of global CO₂ in the year 2021. This paper has explored the potential applications of hydrogen in the hard-to-abate sectors, highlighting its versatility and significance in decarbonization efforts. It provides an overview of hydrogen production methods, emphasizing the importance of sustainable and green hydrogen production. It reviews hydrogen production methods, storage, and potential in blended combustion. In the final part of the article, some considerations are introduced on the possible role of hydrogen in the steel sector (both as a supplementary fuel and as a reducing agent in innovative processes), showing how although there is potential for its inclusion as an element for the decarbonization, it is necessary to evaluate the energy balances of the various processes and the methods of hydrogen production very carefully, in order not to risk obtaining a marginal effect.

Due to the extraordinary mechanical properties of ultra-high-performance concrete (UHPC), the shear stirrups in UHPC beams could potentially be removed. The aim of this study is to determine the effect of beam height and steel fiber volume content on the shear behavior of non-stirrup UHPC beams under a larger shear span-depth ratio (up to 2.8). Eight beams were designed and fabricated, including six non-stirrup UHPC beams and two comparing stirrup-reinforced normal concrete (NC) beams. The experimental results demonstrated that the volume content of steel fiber could be a crucial factor affecting the ductility, cracking strength, and shear strength of non-stirrup UHPC beams and altering their failure modes. Additionally, the height of the beam had a considerable effect on its shear resistance. This study revealed that the French standard formulae were more accurate for the UHPC beams with larger shear span-depth ratios and PCI-2021 formulae greatly overestimate the shear capacity of UHPC beams with larger shear span-depth ratios. Xu’s formulae were more accurate for the steel fiber-reinforced UHPC beams with larger shear span-depth ratios.

Steel damper columns (SDCs) are energy-dissipating members that are suitable for reinforced concrete (RC) buildings and are often used for multistory housing. The evaluation of the peak deformation and hysteretic dissipated energy of such building structures is essential for the rational seismic design of RC buildings with SDCs. In a previous study, the authors proposed an energy-based prediction procedure for the peak and cumulative response of an RC frame building with SDCs. In this procedure, the accuracy of the equivalent velocity of the maximum momentary input energy (V_ΔE1^*)–peak equivalent displacement (D₁^*_max) relationship is essential for high quality predictions. In this article, the V_ΔE1^*–D₁^*_max relationships of RC moment-resisting frames with and without SDCs are invested using a critical pseudo-double impulse (PDI) analysis based on a study by Takewaki and coauthors. The results show that the V_ΔE1^*–D₁^*_max relationship obtained from the critical PDI analysis agrees well with that calculated from the equations proposed in the previous study.

This paper focused on the finite element analysis of structural system in extreme loading condition. Two different stud shape and thicknesses were analyzed under blast. The stud thickness such as 1.19 mm and 1.5 mm were modelled and analyzed using ABAQUS 6.14. FEM is a tool which predicts the engineering physics of the real structure. To validate the finite element modelling performed by authors, a reference work published by earlier researchers on cold-formed steel stud wall is considered and examined in the present study. The novelty of this study was web corrugation and influence of flange width on stud. The models mimic like an air bag in a car to delay the pressure timing inside the stud wall. The mass of explosive used as 1.56 kg at a standard scaled distance. Time versus displacement was captured out at four locations in the stud wall. One of the objectives is to develop mathematical model to validate the deformation of stud under blast loading. Two mathematical models were validated using Artificial Neural Network (ANN). The results captured in ANN model was error histogram, regression plot, best performance fit and training data. The models were capable of resisting the moderate blast load. The response surface methodology (RSM) was employed to evaluate model performance Regression equations are useful for predicting future trends and outcomes, which is crucial for planning and decision-making. The primary goal of this work is to evaluate cold-formed steel stud walls with varying stud sizes under blast loading using finite element analysis and validated by ANN and RSM.

This work aims to explore the impact of side loads, drill-pipe tool-joint (DP-TJ) speed (RPM), and mud type on the austenitic stainless steel SM2535-110 casing wear characteristics. Actual field drill pipe tool joints, casings, and drilling muds are used in this study. The results of the study show that under both types of lubrication, the wear volume increased with radial load and DP-TJ speed. SM2535-110 casing specimens tested under oil-based mud (OBM) lubrication had higher casing wear volumes than those obtained under water-based mud (WBM) lubrication. This unexpected behavior is mainly due to the increase in the surface hardness of the casing specimens tested under WBM. The results also show that the specific wear factor (K) values of specimens tested under WBM are in general 2 to 4 times higher than those obtained under OBM. While K values under WBM increase with both the side load and RPM, those under OBM show a sharp decrease with RPM. This behavior under OBM is due to this lubricant’s higher viscosity and the change of lubrication regime from thin film to thick film lubrication at higher RPM. Scanning electron microscopy (SEM) and the digital microscopic imaging (DMI) of SM235-110 casing specimens show that an aggressive combination of adhesive, abrasive, and plastic deformation was observed under WBM, while the dominant wear mechanism under OBM is abrasive wear.

Concrete-filled steel tube (CFST) members have been widely used in the field of civil engineering due to their advanced superior mechanical properties. However, internal defects such as concrete core voids and interface debonding are likely to weaken the load-carrying capacity and stiffness of these members, which affects safety and serviceability of CFST structures. Visualizing the inner defects of concrete core in CFST members have been a critical need in civil engineering construction, a travel time tomography (TTT) is introduced to quantitatively identify and visualize the sizes and positions of CFST members in this paper. Moreover, a parameter analysis is performed to investigate the relationship between TTT imaging qualities and influence factors, e.g. inversion parameters, defect sizes and positions. The effectiveness and accuracy of the TTT algorithm are verified by several numerical examples and the results demonstrate that TTT can identify the sizes and positions of concrete core void defects in CFST members efficiently and several inversion parameters including model weighting matrix and inversion grid size really pose a significant impact on the imaging results of CFST members. In addition, several optimum parameters are recommended to benefit the future study of the promising TTT approach for CFST members.

Q345 steel is widely used in the construction industry, vehicle manufacturing industry, bridge construction industry and many other aspects due to its excellent comprehensive performance. However, due to its high silicon content, direct hot-dip galvanizing will lead to a series of problems, such as easy peeling of the coating due to the "silicon reactivity". In this paper, we adopt the "two-step hot-dipping method", first hot-dip aluminizing and then hot-dip galvanizing, to isolate the substrate and zinc liquid direct contact, so as to avoid the occurrence of "silicon reactivity". Through the microstructure characterization, neutral salt spray corrosion experiments, electrochemical experiments, the results show that: Al-Zn composite coatings from the inside out were perpendicular to the substrate growth of loose Fe2Al5 layer and Al-Zn layer, outbursts generation; Al-Zn composite coatings resistance to neutral salt spray corrosion was far more than the substrate; Al-Zn composite coatings polarization curve corrosion potential than the substrate was lower than that of the substrate by 0.512V, showing a strong corrosion resistance. It shows extremely strong corrosion resistance.

The response of structures under pulse-like ground motions is characterized by the large amount of energy input in a few cycles. Consequently, structures with insufficient strength may suffer severe damage owing to excessive deformation. In a previous paper, the energy-based prediction procedure for the peak and cumulative response of a reinforced concrete (RC) frame building with steel damper columns was proposed (Fujii and Shioda, 2023). Although this procedure was verified by comparison to the nonlinear time-history analysis (NTHA) results, the performance of the proposed procedure with pulse-like ground motion records has not been verified yet. In this study, the accuracy of the energy-based prediction procedure for an RC frame building with steel damper columns was investigated by considering pulse-like ground motions. The numerical analysis results reveal that the accuracy of the predicted peak response is satisfactory, which agrees with the results of the author’s previous study. However, the accuracy of the predicted total input energy to the building model depends on the ratio of the pulse period of the ground motion to the effective fundamental period of the building model. The reasons for this underestimation of the total input energy are discussed in this paper.

There is a fast-growing interest in the use of selective laser melting (SLM) for metal/alloy additive manufacturing. Our current knowledge of SLM printed 316 stainless steel (SS316) is limited and sometimes appears sporadic, presumably due to the complex interdependent effects of a large number of process variables of the SLM processing. This is reflected from the discrepant findings in the crystallographic textures and microstructures in this investigation with those reported in the literatures, which also vary itself. The as-printed material is macroscopically asymmetric in both the structures and crystallographic textures. The <101> and <111> crystallographic directions align parallel with the SLM scanning direction (SD) and build direction (BD), respectively. Like-wise, some characteristic low angle boundary features are reported crystallographic, while this investigation unequivocally proves them non-crystallographic since they always maintain an identical alignment with the SLM laser scanning direction irrespective of the matrix material’s crystal orientation. There is also 500±200 nm columnar or cellular features, depending on the cross-section, generally found all over the sample. These columnar or cellular features are formed with walls made of dense packing of dislocations entangled with Mn, Si and O enriched amorphous inclusions. They remain stable after the ASM solution treatments at 1050 °C temperatures, and therefore, are capable of hindering boundary migration events of recrystallization and grain growth. Thus, the nanoscale structures can be retained at high temperatures. Large 2-4 µm inclusions form during the solution treatment, within which the chemical and phase distribution are heterogeneous.

This research is aimed to develop the method for damage degree evaluation in metals and alloys during their deformation and destruction based on acoustic emission (AE) technique. Experimental studies were carried out on tensile specimens of high-strength steel with simultaneous registration of AE signals in tested material. It was shown that the time-dependent AE primary parameters, such as the AE signal maximum amplitudes and AE activity, do not have a clear relationship with the material damage degree. This fact makes it difficult to use standard methods for assessing the damage degree of acoustic signal sources, including defects. It was proposed to use the Kolmogorov-Smirnov criterion to differ the processes of metal plastic deformation and crack propagation during the rupture. The possibility of estimating the material damage degree by high-energy AE hits share was shown. Besides, a particular expression was obtained for evaluating the damage degree for the material under study.

Three kinds of Ni based alloy cladding coatings were prepared on 316L stainless steel at different power. The microstructure of the cladding layer was observed and analyzed by XRD, metallographic microscope and SEM. The hardness of the cladding layer was measured, and the wear resistance of the cladding layer was tested by friction instrument. The results show that the effect of laser cladding is good and the cladding layer has a good metallurgical bonding with the substrate. Different microstructures such as dendritic and equiaxed grains can be observed in the cladding layer. With the increase of laser power, more equiaxed and columnar dendrites can be observed. The phase composition of the cladding layer is mainly composed of γ - Ni solid solution and some intermetallic compounds such as Ni3B, Cr5B3 and Ni17Si3. The results of EDS show that there are some differences in the distribution of C and Si between dendrites. The hardness of the cladding layer is about 600 HV0.2, which is about three times of the substrate (~ 200 HV0.2). Through the analysis of the wear morphology, the substrate wear is serious, there are serious shedding, mainly adhesive wear and abrasive wear. However, the wear of cladding layer is slight, which is abrasive wear, and there are some grooves on the surface.

Microalloying of low carbon steel with niobium (Nb) and titanium (Ti) is standardly applied in high-strength low-alloy (HSLA) steels enabling austenite conditioning during thermo-mechanical controlled processing (TMCP), which results in pronounced grain refinement in the finished steel. The metallurgical effects of microalloying elements are related solute drag and precipitate particle pinning, both acting on the austenite grain boundary thereby delaying or suppressing recrystallization of the deformed grain. In that respect it is important to better understand the precipitation kinetics as well as the precipitation sequence in a typical Nb-Ti-microalloyed steel. Various characterization methods have been utilized in this study for tracing microalloy precipitation after simulating different austenite TMCP conditions in a Gleeble apparatus. Atom probe tomography (APT), scanning transmission electron microscopy in a focused ion beam equipped scanning electron microscope (STEM-on-FIB) and electrical resistivity measurements provide complementary information on the precipitation status and are correlated with each other. It will be demonstrated that accurate electrical resistivity measurements can monitor the general consumption of solute microalloys (Nb) during hot working which was complemented by APT measurements of the steel matrix. On the other hand, STEM revealed that a large part of Nb-containing particles during hot working are co-precipitated with titanium during cooling from the austenitizing temperature. Precipitates that form during cooling or isothermal holding can be distinguished from strain-induced precipitates by corroborating STEM measurements with APT results. APT specifically allows obtaining detailed information about the chemical composition of precipitates as well as the distribution of elements inside the particle. Electrical resistivity measurement, on the contrary, provides macroscopic information on the progress of precipitation and can be calibrated by APT. The current paper highlights the complementarity of these methods and shows first results within the framework of a larger study on strain-induced precipitation.

Optical fiber measurement systems have recently gained popularity following a multitude of intensive investigations. A new technique has been developed for these measurement systems that uses Rayleigh backscatter to determine the distributed strain measurement over the total length of a fiber. These measurement systems have great potential in civil engineering and structural health monitoring. This paper addresses some preliminary comparisons between three different fiber coatings and six different adhesives on steel structures. The results are based on a bending test with specimens made of precision flat steel; optical fiber strain measurements were compared with photogrammetric strain measurements. Analysis of the test data showed a strong correlation between the optical measurement system’s results and the theoretical results up to the yielding point of the steel. Furthermore, the results indicate that fibers with the Ormocer® and polyimide coatings have almost no loss in the strain measurements. The main results of this investigation are a guideline describing how to attach optical fibers to steel surfaces for distributed fiber optical strain measurements and recommendations for coatings to obtain realistic strain values. Additionally, the advantages of distributed strain measurements were revealed, which illustrates the potential of Rayleigh backscattering applications.

The efficiency of cold sheet and strip rolling of steels and non-ferrous metals in the main depends on the quality of the technological lubricant and its cost. In this regard, it is important to develop new compositions of effective metal-working coolants (MWC) having low cost and providing the maximum reduction in the friction coefficient. We developed and tested the new compositions of the MWC on basis of chicken fat, and mono- and diglycerides and their esters of boric acid synthesized from the wastes of sunflower oil production. The MWC were tested in DSEA on laboratory rolling mill 100x100 with a roll diameter of 260 mm during steel 08Kp rolling. The efficiency of the coolants was determined by the factor of metal stretch forming λ and the coefficient of friction μ in the deformation zone which was found by forward slip method. We found the metal-working coolant with 100 % concentration of boric acid esters of mono- and diglycerides is the most effective in steel rolling. Thus the new MWC on basis of boric acid esters of mono- and diglycerides synthesized from the wastes of sunflower oil production can be recommended for use in rolling of structural steels on account of availability, high efficiency, and a low cost.

The effectiveness of a hybrid technique for identifying seismic damage in planar, multistory, steel X or V-braced frames is demonstrated here through an example of a six-story frame. This proposed technique, referred to as “M and P”, combines the instrumental Monitoring (M) with Pushover analysis (P). According to the methodology, the diagram of stepping eigenfrequencies of the frame in the inelastic region is initially plotted against seismic roof displacement. The fundamental natural frequency detected via the monitoring process is then utilized in this key diagram to reveal the inelastic roof displacement that corresponds to the damage state of the steel braced frame. This displacement is subsequently used as the target in the pushover analysis, facilitating the identification of seismic damage in the existing steel braced frame. Finally, the damage image is correlated with the damage stiffness matrix of the frame at the same inelastic roof displacement. The investigation results indicate that combining instrumental monitoring with pushover analysis enables accurate identification of seismic damage potential in existing steel braced frames.

The study’s objective is to analyse the mechanical properties of steel pipe piles as a part of a trestle bridge subjected to five years of natural marine corrosion degradation. Sixteen tensile specimens were extracted from the steel pipe piles in the splash, tidal, and immersion zones. The experimental tensile test results are used to establish regression equations defining elastic modulus, yield strength, strain hardening index, and strength coefficient for the true stress-strain curves of the three regions. A non-linear time-dependent mathematical model is exploited to identify the corrosion degradation using the data from one single corrosion degradation measurement campaign. The analysis indicated that the splash zone experiences the most severe corrosion degradation, and there are progressive losses in the mechanical properties of each zone as the corrosion degradation progresses. The established relationships of the mechanical properties, as a function of the ratio of corroded plate thickness to the as-built one, can be used as a fast-engineering approach to identify the mechanical properties of severely corroded piles. The corrosion degradation allowance is also defined using the First Order Reliability Method, accounting for existing uncertainties covered by the partial safety factors. By examining the impact of marine corrosion on the mechanical properties of marine structures and developing predictive models to assess the corrosion’s effect on material strength and corrosion allowance, the study aims to improve offshore structures’ safety, design, and maintenance.

The stress concentrations have become common phenomenon of steel elements when arresting a fracture by implementing the crack stop hole (CSH) technique. Embedding the CSH with Carbon Fibre Reinforced Polymer (CFRP) enhance the fatigue life by delaying the fractures while achieving a stiffness recovery due to superior mechanical characteristics of CFRP material. Hence, low cyclic fatigue (LCF) behaviour of 162 strengthened and non-strengthened CSH specimens were examined in this context. These specimens were subjected to a range of 0 to10,000 fatigue load cycles with the frequency of 5 Hz. At the end of fatigue exposure, the average tensile strength was measured in each case. The average strength reductions in the range between 13% to 25% was noted in steel elements with CSH subjected to fatigue exposure. The application of a CFRP patch on CSH had effectively recovered the strength losses while enhancing the strength in the range between 32% to 45% with respect to the non-strengthened non specimens. The developed numerical model based on cyclic J-integral technique agrees with test results and is capable of predicting characteristics for this novel hybrid technique.

Elastic properties of materials and their changes with temperature are important for their applications in engineering. A study on the influence of phase composition of AISI 4130 alloy on Young's modulus (Ed), shear modulus (Gd), and damping (Q-1) was carried out by Impulse Excitation Technique (IET). The material characterization was carried out using confocal microscopy, XRD, MET, HV, and dilatometry. A stable structure, composed of ferrite (BCC) and pearlite (α-Fe+Fe3C), was obtained by annealing. Metastable structure of martensite (BCT) was obtained by quenching. The Ed, Gd, and Q-1 were measured, varying the temperature from RT to 900 °C. The values of Ed and Gd, at RT, were determined as 201.5 and 79.2 GPa (annealed), and 190.13 and 76.5 GPa (quenched), respectively. In the annealed steel, the values Ed and Gd decrease linearly on heating up to 650 °C, with the thermal expansion. In the quenched steel, weak changes in the dilatometric curve, Ed, Gd, and Q-1, in the range of 350-450 °C, indicated decompositions of the martensitic phase. Sharp decrease in the moduli and high peak of Q-1, was observed for both samples around 650-900 °C, revealing low lattice elastic stability of the phases during transformations α(BCC)+Fe3C↔γ(FCC).

Super duplex stainless steel (SDSS) is used for manufacturing large valves and pipes in offshore plants because of its excellent strength and corrosion resistance. Large valves and pipes are manufactured by forging after casting, and the outside and inside microstructures are different owing to the difference in the cooling rate caused by the thermal conductivity. This microstructural variation causes cracks during solution annealing, which breaks the materials. To study toe corrosion resistance of the SDSS forged material, the microstructure was conducted based on the difference in the cooling rate between the inside and outside of the cast SDSS. To analyze the effects of the secondary phase fraction before solution annealing on the solution and corrosion resistance, the corrosion resistance with and without solution annealing was measured using the potentiodynamic polarization test and critical temperature test after the precipitation of the secondary phase. In the potentiodynamic polarization test, the secondary phase decreased the activation polarization and increased the corrosion rate. The critical pitting temperature exhibited the effect of the secondary phase.

Near-neutral pH and low redox potentials (EH) are considered favorable conditions for radionuclides immobilization in deep repository systems in clay geological formations. Cigeo is a future Industrial Centre for Geological Disposal for Nuclear Waste (NW) for high-level and intermediate level long-lived radioactive waste, to be built in France, at 500 m depth within the Callovo-Oxfordian clay formation. Deep knowledge of the mechanisms and kinetics of corrosion occurring at the external surface of tubings made of API 5L X65 carbon steel (CS-X65) in contact with COx pore water, is essential for a reversible NW management of the Cigeo site. By using robust handmade electrodes and electrochemical and gravimetric techniques, this work aimed to determine the corrosion phenomenology and kinetics of CS-X65 in contact with COx pore water flowing continuously through a Multi-Parameter Probe (MPP) device, placed at 500 m depth, for more than 180 days. It also aimed at demonstrating the reliability and the robustness of the measurement methodology for the corrosion evaluation of the metallic liner of the future nuclear waste disposal site. Two iron oxidants were encountered, oxygen, who was depleted, and proton, who was accompanied by hydrogen sulfide. Corrosion mechanisms and kinetics were well established for two CS-X65, electrochemically perturbed and not. The corrosion thickness loss rates stand between 0.016 and 0.032 mm/y.

The purpose of this study is to analyse the feasibility of using waste from granite gang saws (GCW-GS) to manufacture ultra-high performance, steel-fibre reinforced concrete (UHPFRC). These machines cut granite blocks by abrasion using a steel blade and slurry containing fine steel grit. The waste generated by gang saws (GCW-GS) contains up to 15% Fe2O3 and up to 5% CaO. This is the main difference from the waste produced by diamond saws (GCW-D). Consequently, the second objective of this study is to compare the results of the waste obtained with gang saws with that from diamond saws, in order to determine the influence of iron and calcium oxides. The waste from cutting granite with gang saws was used in different percentages to replace micronized quartz powder of natural origin in the manufacture of UHPRFC. All the test specimens were analysed to determine their compressive strength, elasticity modulus, flexural strength and indirect tensile strength. The final conclusion is that wastes from both gang saws and diamond saws can be used to manufacture UHPFRC with an improvement in the mechanical properties up to a 35% replacement. The results for GCW-GS are better, mainly due to the pozzolanic effect of the iron dioxide. For higher percentage replacements the mechanical properties are close to the control concrete with small decreases.

This work studied the corrosion of welded pipes and how welding destroyed surface film of pipes. Surface reaction of a welded pipe is key to understanding phenomena and important factors during the corrosion. This paper presents experiment and CFD modeling approaches of a welded pipe corrosion under salt vapor condition. The pipes were welded at currents of 60 A,70 A and 80 A to observe the effect of welding current on corrosion. A welded pipe is a stainless-steel ASTM A312 grade 304L and period of experiment about 0-600 hours that they are tested in vertical and horizontal alignments. In CFD software, there is not direct model of corrosion but it can use surface reaction and create add-on species and chemical reaction technique for imitating the corrosion mechanism. The modeling approaches of corrosion have presented in 3-dimensional transient times in CFD simulation. Surface reactions were performed by Species Model which involve site species. Site species in Species Model took place at gas-solid interfaces and in this case are salt vapor and surface pipe. Chemical reaction rate on the surface controls lost weight of a welded pipe and the model can be validated with experiment. In conclusion, in period 0-600 hours error between CFD modeling and experiment have error trend decreased. The error at 600 hours is 6% both of vertical pipe and horizontal pipe test. The modeling approaches closely with the performed experiment and can be accepted. Moreover, the model is able to predict corrosion of a welded pipe of different sizes and their lost weight after 600 hours without experiment. Also the model can predict lifetime of pipe.

Copper-containing materials are attracting attention as self-desinfecting surfaces, suitable for helping healthcare settings in reducing healthcare associated infections. However, the impact of repeated exposure to disinfectants frequently used in biocleaning protocols on their antibacterial activity remains insufficiently characterized. This study aimed at evaluating the antibacterial effi-ciency of copper (positive control), a brass alloy (AB+®) and stainless steel (negative control) after repeated exposure to a quaternary ammonium compound and/or a mix of peracetic acid/hydrogen peroxide routinely used in healthcare settings. A panel of 6 antibiotic-resistant strains (clinical isolates) was selected for this assessment. After a short (5 min) exposure time, the copper and brass materials retained significantly better antibacterial efficiencies than stainless steel, whatever the bacterial strain or disinfectant treatment considered. Moreover, post-treatment with both disinfectant products, copper-containing materials still reached similar levels of antibacterial efficiency as those obtained before treatment. Antibiotic resistance mechanisms such as efflux pump overexpression did not impair the antibacterial efficiency of copper-containing materials, neither did the presence of one or several genes related to copper homeostasis/resistance. In light of those results, surfaces made out of copper and brass remain interesting tools in the fight against dissemination of antibiotic-resistant strains that might cause healthcare associated infections.

This study presents a comprehensive comparative analysis of retrofitting techniques aimed at enhancing the seismic resilience of seismically vulnerable historical buildings. Recognizing the dual objectives of structural safety and architectural preservation, this research evaluates and compares several advanced retrofitting methods, including base isolation, strengthening of masonry, steel bracing systems, Fiber-Reinforced Polymer (FRP) wrapping, and damping devices. Each technique is critically assessed based on its effectiveness in mitigating seismic risks, its compatibility with historical architectural features, and its applicability to various building types. Base isolation is highlighted for its ability to decouple buildings from ground motion, thereby significantly reducing seismic forces and protecting architectural integrity. Strengthening of masonry through the use of fiber-reinforced polymers and steel elements enhances the ductility and strength of masonry walls, making them more resilient to seismic forces. Steel bracing systems are shown to provide essential lateral support, particularly in timber-framed structures, improving overall stability and reducing deformation during earthquakes. FRP wrapping is identified as a versatile technique that strengthens structural elements without compromising aesthetic value, making it suitable for reinforcing concrete and masonry components. Damping devices, including viscous dampers and tuned mass dampers, are discussed for their ability to dissipate seismic energy and control structural vibrations, offering a minimally invasive solution that preserves historical aesthetics. The study also addresses several challenges and research gaps associated with these retrofitting techniques, such as ensuring architectural compatibility, assessing long-term material performance, optimizing cost-effectiveness, and navigating complex regulatory frameworks. By advancing knowledge in these areas, the research aims to foster interdisciplinary collaboration and innovation in the development of retrofitting solutions. Ultimately, this study contributes to the ongoing efforts to safeguard historical buildings against seismic hazards. By leveraging cutting-edge technologies and best practices in structural engineering and architectural conservation, stakeholders can develop sustainable, cost-effective, and culturally sensitive retrofitting strategies that protect valuable cultural heritage for future generations.

The magnetic properties of 0.10 mm ultra-thin grain-oriented (UTGO) silicon steel and Fe-based amorphous (FBA) alloy under sinusoidal excitation were measured experimentally, and the magnetic field strength and iron loss of the two materials under different frequencies and magnetic densities were obtained. Based on the measured data, the magnetization and loss characteristics of the two materials were analyzed and compared. Furthermore, two Epstein square ring models of the same specification and different materials were designed, and the reliability of the models was verified. Then, the electromagnetic characteristics of the two Epstein square ring models at higher and lower frequencies were calculated by using the finite element method, and the iron loss was obtained and compared. The results show that the FBA alloy has good application characteristics at low frequency and low power, and the 0.10 mm UTGO silicon steel has good application characteristics at high frequency and high power. This research can provide important data basis to promote the application of these two materials in new energy equipment.

High-rise building machines (HBMs) play a critical role in the successful construction of super-high skyscrapers, providing essential support and ensuring safety. The HBM’s climbing system relies on a jacking mechanism consisting of several independent jacking cylinders. A reliable control system is imperative to maintain a smooth posture of the construction steel platform (SP) under the action of the jacking mechanism. This research introduces three multivariate time series neural network models—namely, Long Short-Term Memory (LSTM), Gated Recurrent Unit (GRU), and Temporal Convolutional Network (TCN)—to predict the posture of HBM. The models take pressure and stroke measurements from the jacking cylinders as inputs, and their outputs determine the levelness of the SP and the posture of the HBM at various climbing stages. The development and training of these neural networks are based on historical on-site data, with the predictions subjected to thorough comparative analysis. All proposed neural network models exhibit the capability to dynamically predict the posture of the HBM during the climbing process, using data from sensors. Notably, the GRU model shows better predictive performance.

Keywords: Wall-like RC columns; Strengthening; FRP; NSM rebars; Steel plates; Testing; FE modeling; Preloading.

In order to obtain the good match between yield strength and low-temperature toughness, the short-time partial austenitization (SPA) process was employed for V-microalloying 0.22C-5.24Mn steel. The initial microstructure after intercritical tempering was dual-phase ferrite and reversed austenite (RA), while the final microstructure was consisted of ferrite, RA and secondary martensite (SM) after subjected to SPA process. (V, Mo)C with disc-like morphology mainly precipitated during intercritial tempering, and the aspect ratio of particle decreased, leading to the appearance of near-spherical morphology. After subjected to SPA process, the resultant multiphase hierarchical microstructure (three layers: out layer of ferrite, interlayer of SM and inner layer RA) enabled high yield strength of 1097 MPa, total elongation of 14%, and impressive impact energy of 33.3 J at -20 °C. The strengthening contribution of (V, Mo)C precipitation was estimated about 108 MPa.

Abstract: In recent years, the construction engineering sector has undergone a transformative shift towards the integration of machine learning (ML) techniques, particularly in predicting the properties of steel fiber-reinforced concrete (SFRC). Despite the theoretical sophistication of existing models, a persistent challenge remains – their opacity, lacking transparency and real-world relevance for practi-tioners. To address this gap and advance our current understanding, this study employs the extra gradient (XG) Boosting algorithm, crafting a comprehensive ap-proach. Grounded in a meticulously curated database drawn from 43 seminal pub-lications, encompassing 420 distinct records, this research focuses predominantly on three primary fiber types: crimped, hooked, and mil-cut. Complemented by hands-on experimentation involving 20 diverse SFRC mixtures, this empirical campaign is further illuminated through the strategic use of Partial Dependence Plots (PDPs), revealing intricate relationships between input parameters and con-sequent compressive strength. A pivotal revelation of this research lies in the identification of optimal SFRC formulations, offering tangible insights for real-world applications. The developed ML model stands out not only for its sophistication but also its tangible accuracy, evidenced by exemplary performance against inde-pendent datasets, boasting a commendable mean target-prediction ratio of 99%. To bridge the theory-practice gap, we introduce a user-friendly digital interface, thri-ughly designed to guide professionals in optimizing and accurately predicting the compressive strength of SFRC. This research thus contributes to the construction and civil engineering sectors by enhancing predictive capabilities and refining mix designs, fostering innovation, and addressing the evolving needs of the industry.

In this work, a systematic study was conducted on the fabrication of multi-material components obtained employing Laser-Powder Bed Fusion (L-PBF) technology. The idea of making multi-material components is a winning capability of additive technologies because it allows the fabrication of Functionally Graded Materials (FGMs) with the customization of parts according to different required properties. The transition from one material to another was achieved gradually and continuously within the same layer using ad-hoc equipment designed for L-PBF systems with a powder spreading technique based on coaters or rollers. The influence of the relative position of the different materials within the powder chamber and the geometry of the developed equipment on the metallurgical and mechanical properties of the manufactured samples was evaluated. The performed tests involved the use of two materials, a nickel-based superalloy, and a stainless steel, having different chemical, physical and mechanical properties to obtain gradual properties variation in the manufactured samples. Based on the results of post-process characterization obtained through metallographic, chemical, and mechanical analysis, the relative positions of the materials and the geometry of the developed equipment have a limited effect on the sample’s manufactured properties. The characteristics of the FGM zone depend on the nature of the employed powders, and its extent coincides with that defined during the design of the divider.

A multi-strand composite welding wire was applied to join high nitrogen austenitic stainless steel, and microstructures and mechanical properties were investigated. The electrical signals demonstrate that the welding process using a multi-strand composite welding wire is highly stable. The welded joints are composed of columnar austenite and dendritic ferrite and welded joints obtained under high heat input and cooling rate have a noticeable coarse-grained heat-affected zone and larger columnar austenite in weld seam. Compared with welded joints obtained under the high heat input and cooling rate, welded joints have the higher fractions of deformed grains, high angle grain boundaries, Schmid factor and the lower dislocation density under the low heat input and cooling rate, which indicate a lower tensile strength and higher yield strength. The rotated goss (G_RD) orientation of a thin plate and the cube (C) orientation of a thick plate are obvious after welding, but the S orientation at 65° sections of Euler’s space is weak. The δ-ferrite was studied based on the primary ferrite solidification mode. It is observed that low heat input and high cooing rate result in the increasing of δ-ferrite and high dislocation density was obtained in grain boundaries of δ-ferrite. M₂₃C₆ precipitates due to low cooling rate and heat input in weld seam and deteriorates the elongation of welded joints. The engineering stress-strain curves also show the low elongation and tensile strength of welded joints under low heat input and cooling rate, which is mainly caused by the high fraction of δ-ferrite and the precipitation of M₂₃C₆.

This research investigated high-temperature corrosion (500 °C) of Cr-Mo steel processed using water jet peening or multifunction cavitation (MFC), and the suitability of such steel for high-temperature boilers and reaction vessels. High-temperature corrosion was induced using an embedment test and a coating test using sulfide-type K2SO4-Na2SO4 powder. To measure the relaxation of the residual stress due to the decrease in work hardening caused by an increase in specimen temperature and the difference in thermal shrinkage between the surface and interior of the specimen, a thermal cycling test was conducted. For the MFC-processed specimen, the oxide film that formed on the surface suppressed mass loss, prevented crack formation, and reduced the compressive residual stress caused by high-temperature corrosion. MFC-processed Cr-Mo steel is thus suitable for a high-temperature corrosion environment.

This study sought to investigate steel frames’ performance with dual lateral loader system (Frame bending + bracings of divergent and convergent) in near and far filed to fault. In order to this, four categories of steel frame with dual system with 8, 10 and 12 story are designed with average formation based on existing seismic regulation in 2800 standard of Iran and tenth chapter of national regulations of construction (planning and performing steel construction). Time history non-linear dynamic analysis under the effect of near and far field earthquakes has been done on plan’s models. Then the maximum of floors’ dislocation, floors’ drift, roof dislocation, base shear and energy curves of frames are shown and compared with each other. All non-linear time history analyses have been accomplished using PERFORM 3D software.

Induction heating is a fast, reproducible, and efficient heating method used in various manufacturing processes. However, there is no established additive manufacturing (AM) process based on induction heating using wire as feedstock. This study investigates a novel approach to AM based on inductive heating, where a steel wire is melted and droplets are detached periodically using a two-winding induction coil. The process parameters and energy input into the droplets are characterized. The induction generator exhibits sluggish response to the excitation voltage, resulting in a lag in the coil current. The process is captured using a high-speed camera, revealing regular droplet formation and uniform size and shape when operated within an appropriate process window. Larger drops and increased spatter formation occur outside this window. The proposed method allows for the production of droplets with almost spherical shapes. Further analysis and characterization of droplet formation and energy input provide insights into process optimization and overall efficiency.

This study determines the equivalent stress intensity factor (SIF) model that best fits the experimental behavior of low-carbon steel under mixed mode (I and II). The study assessed Tanaka, Richard, and Pook's equivalent SIF models. The theoretical values used for comparison correspond to experimental results in a modified C(T) geometry by machining a hole ahead of the crack tip subjected to fatigue loads with a load ratio of R = 0.1. The comparison involved the SIF for six experimental points and the values computed through the numerical simulation. The Paris, Klesnil, and modified Forman-Newman crack growth models were used with each equivalent SIF to analyze the prediction in the estimated number of cycles. The Klesnil model showed the closest prediction since the error between the calculated and experimentally recorded number of cycles is the lowest. However, the material behavior reflects a reduced crack propagation rate attributed to plasticity in the crack tip. Results suggest that Asaro equivalent SIF conservatively estimates the element lifespan with increasing errors from 2.3% at the start of growth to 27 % at the end of the calculation.

This paper presents a numerical study on the vertical (axial) and lateral (flexure) behavior of CFST (Concrete-Filled Steel Tube) columns with active hoop prestress; this transverse prestressing effect is achieved by bolting together two steel half-tubes. This study refers to new construction only (i.e., no retrofit). 12 prototype CFST column specimens (segments) are analyzed. These specimens differ in the prestressing force (3 levels) and in the gravity loading ratio (4 levels); they are selected to represent typical ground columns of mid-rise buildings. The structural behavior of these column specimens is simulated with a nonlinear model implemented in Abaqus; the concrete and steel behavior are described with a damage-plasticity and a plasticity model, respectively. Finally, the interface concrete-steel interaction is represented by a hard (compression-only) surface-to-surface contact model. The calculations involve three consecutive loading steps: (i) transverse prestress, (ii) axial force, and (iii) lateral loading (shear force and bending moment). The structural behavior of the CFST columns is deeply examined and discussed; the results show that their axial-flexural capacity is adequate. Noticeably, it is concluded that the overall benefits of prestressing the columns are only modest. Preliminary studies on the aforementioned mid-rise buildings equipped with the CFST columns show that their gravity and wind capacities are largely enough; conversely, their seismic capacity is sufficient for moderate seismic ground motions only.

The tribological performance of metalwork steel tools is of vital importance in both cold and hot working processes. One solution for improving metal tool life is the application of coatings. This paper investigates the effect of CrAlSiN thin-film PVD-deposition on the tribological behaviour of tool steel K340. The sliding wear performance of the coated K340 steel is analysed in relation to both the uncoated K340 steel and a range of tool steels dedicated to hot- and cold-working, such as X155CrVMo12-1, X37CrMoV5-1, X40CrMoV5-1, 40CrMnMo7 and 90MnCrV8. The investigated tool steels were heat-treated, while K340 was subjected to thermochemical treatment and then coated with a CrAlSiN hard film (K340/CrAlSiN). The hardness, chemical composition, phase structure and microstructure of steels K340 and K340/CrAlSiN are examined. Tribological tests were conducted using the ball-on-disc tester in compliance with the ASTM G99 standard. The tests were performed under dry unidirectional sliding conditions, using an Al2O3 ball as a counterbody. The wear factor and coefficient of friction are estimated and analysed with respect to hardness and alloying composition of the materials under study. SEM observations are made to identify the sliding wear mechanisms of the analysed tool steels and PVD-coated K340 steel. In contrast to the harsh abrasive-adhesive wear mechanism observed for uncoated tool steels, the abrasive wear dominates in case of the AlCrSiN. The deposited thin film effectively prevents the K304 substrate from harsh wear severe degradation. Moreover, thanks to the deposited coating, the K304/CrAlSiN sample has a COF of 0.529 and a wear factor of K=5.68×10−7 m3 N−1 m−1, while the COF of the reference tool steels ranges from 0.702 to 0.885 and their wear factor ranges from 1.68×10−5 m3 N−1 m−1 to 3.67×10−5 m3 N−1 m−1. The CrAlSiN deposition reduces the wear of the K340 steel and improves its sliding properties, which makes it a promising method for prolonging the service life of metalwork tools.

Fibre reinforced cementitious materials (FRC) have become an attractive alternative for structural applications. Among such FRC, steel and polyolefin fibre reinforced concrete and glass fibre reinforced concrete are the most used ones. However, in order to exploit the properties of such materials structural designers need constitutive relations that reproduce FRC fracture behaviour accurately. This contribution analyses the suitability of multilinear softening functions combined with a cohesive crack approach for reproducing the fracture behaviour of the FRC previously mentioned. The implementation performed accurately simulates the fracture behaviour while being versatile, robust and efficient from a numerical point of view.

The study presents a comparative approach between response surface methodology (RSM) and hybridized, genetic algorithm artificial neural network (GA-ANN) in predicting the water absorption, compressive strength, flexural strength split tensile strength and slump for steel fiber reinforced concrete. The effect of process variables such as aspect ratio, water cement ratio and cement content were investigated using the central composite design of response surface methodology. This same experimental design was used in training the hybrid-training approach of artificial neural network. The predicting ability of both methodologies were compared using the root mean sqaured error (RMSE), mean absolute error (MAE), model predictive error (MPE) and absolute average deviation (AAD). The RSM model was found more accurate in prediction compared to hybrid GA-ANN.

Combining modern thermodynamics theory branches, including finite time thermodynamics or entropy generation minimization, constructal theory and entransy theory, with metallurgical process engineering, this paper provides a new exploration on generalized thermodynamic optimization theory for iron and steel production processes. The theoretical core is to thermodynamically optimize performances of elemental packages, working procedure modules, functional subsystems, and whole process of iron and steel production processes with real finite-resource and/or finite-size constraints with various irreversibilities toward saving energy, decreasing consumption, reducing emission and increasing yield, and to achieve the comprehensive coordination among the material flow, energy flow and environment of the hierarchical process systems. A series of application cases of the theory are reviewed. It can provide a new angle of view for the iron and steel production processes from thermodynamics, and can also provide some guidelines for other process industries.

Structural integrity of buried pipelines is threatened by the effects of Permanent Ground Deformation (PGD), resulting from seismic-induced landslides and lateral spreading due to liquefaction parallel to the pipeline axis, requiring accurate analysis of the system performance. Analytical fragility functions allow to estimate the likelihood of seismic damage along the pipeline, supporting design engineers and network operators in prioritizing resource allocation for mitigative or remedial measures in spatially distributed lifeline systems. To efficiently and accurately evaluate the seismic fragility of buried operating steel pipeline under longitudinal PGD, this study develops an analytical model considering the asymmetric pipeline material behavior in tension and compression under varying operational loads. The validated model is further implemented within a fragility function calculation framework based on Monte Carlo Simulation (MCS), allowing to assess the probability of exceedance of the pipeline performance limit states conditioned to the intensity of PGD. The evaluated fragility surfaces showed that the pipeline probability of exceeding the performance criteria increases for larger soil displacement and lengths, as well as cover depths, because of the greater mobilized soil reaction counteracting pipeline deformation. Additionally, the performed Global Sensitivity Analysis (GSA) highlighted the influence of the PGD and soil-pipeline interaction parameters, as well as the effect of the service loads on structural performance, requiring proper consideration in pipeline system modeling and design. Finally, the proposed analytical fragility function calculation framework provides a useful methodology for effectively assessing the performance of operating pipelines under longitudinal PGD, quantifying the effect of the uncertain parameters impacting structural response.

Modular steel buildings (MSBs) interlocking inter-module connections (IMCs) have piqued researchers’ interest. However, the existing literature has not yet studied the optimisation of its plate thicknesses. This paper, therefore, focuses on optimising interlocking (IMCs) plate thickness in (MSBs), leveraging previous experimental and numerical simulation methodologies. Various numerical models for four MSBs interlocking (IMCs) with plate thicknesses (4 mm, 6 mm, 10 mm, and 12 mm) were developed under compression loading conditions. The study’s novelty lay in its comprehensive parametric analysis, which evaluated the slip phenomenon in (MSBs) connections and introduced a slip prediction model validated against empirical data. Further innovative machine learning approach was utilised to predict slip values based on applied force through a random forest regression model trained using the 'Treebagger' function. Sensitivity analysis and comparisons with alternative methods were utilised to underscore the reliability and applicability of the findings. The results showed that 11.03 mm was the optimal plate thickness for interlocking (IMCs) in modular steel buildings, with up to 8.08% reduced material costs. Increasing plate thickness boosts its deformation resistance by up to 50.75%. ‘TreeBagger’ random forest for anomaly detection and machine learning improves slip prediction up to 7% at higher force levels.

The demand for efficient processes through a comprehensive understanding and optimization of welding conditions continues to grow in the manufacturing industry. This study involves heat-resistant 2.25 Cr-1 Mo V-groove steel welding using the square-waveform alternating cur-rent. Experiments were conducted to build the relationship between input variables—such as current, frequency, electrode negativity ratio, and welding speed—and process performance, such as penetration, bay area, deposition rate, melting efficiency, percentage dilution, flux–wire ratio, and heat input. The process was analyzed in light of the defect-free high-deposition weld groove weld, the sensitivity to process parameters, and the optimization and development of the process map. The study proposes an innovative approach to reducing the cost and time of optimizing the one-pass-each-layer V-groove welding process using bead-on-plate welds. Square waveform welding creates a metallurgical notch in the form of a bay at the fusion boundary that can be minimized by selecting appropriate welding conditions. The square waveform submerged arc welding is more sensitive towards changes in current and welding speed than the frequency and electrode negativity ratio; however, the electrode negativity ratio and frequency are minor but helpful parameters to achieve optimal results. The proximity of the planned and experimental results to within 3% confirms the validity of the proposed approach. The investigation shows that 90% of the maximum deposition rate is possible for one-pass-each-layer V-groove welds within heat input and weld width constraints.

The preservation of the authenticity of a building artefact is a responsible practice. On the other side, the need to save the building artefact from the natural and anthropic degradation, to ensure the structural reliability to the different actions, to define an efficient maintenance program are big challenges, that involves the cooperation of several professionals, responsible use of innovative techniques and materials that are nowadays available. This paper focuses on a specific design approach for the rehabilitation works of ancient constructions in archaeological sites. The proposed conceptual design approach implies different steps that allow the optimization of the design at an increasing level of knowledge on the existing structures and their materials. The design procedure on historical constructions generally includes the following steps: the collection of data, the structural identification, hazard, and vulnerability analysis, damage and risk analysis, a cost-benefit analysis, so only at the end of the process, the final design is achieved. In the archaeological area, some important design aspects cannot be defined before the execution work phase, since some elements could be revealed and identified during work execution, as a consequence, the final design has been often optimized after all this information has been acquired. A studied case in the archaeological site of Pompeii is herein presented to prove the efficiency of the proposed approach.

The present work deals with the development of finite element methodology for obtaining the stress distributions in thick cylindrical HK40 stainless steel pipe that carry high temperature fluids. The material properties and loading are assumed to be random variables. Thermal stresses that are generated along radial, axial and tangential directions are computed generally using analytical expressions which are very complex. To circumvent such an issue, the probability theory and mathematical statistics have been applied to many engineering problems which allows to determine the safety both quantitatively and objectively based on the concepts of reliability. Monte Carlo simulation methodology is used to study the probabilistic characteristics of thermal stresses which is used for estimating the probabilistic distributions of stresses against the variations arising due to material properties and load. A 2-D Probabilistic finite element code is developed in MATLAB and the deterministic solution is compared with ABAQUS solutions. The values of stresses that are obtained from the variation of elastic modulus are found to be low as compared to the case where the load alone is varying. The probability of failure of the pipe structure is predicted against the variations in internal pressure and thermal gradient. These finite element framework developments are useful for the life estimation of piping structures in high temperature applications and subsequently quantifying the uncertainties in loading and material properties.

Recently many researches of EOS (Electric Arc Furnace Oxidizing Slag) on application to construction industry have been carried out with increasing its production and limited reclamation site. EOS can be used as a fine aggregate for construction material, however, its engineering properties vary with the manufacturing process and producing district, causing a quality differences in material performance. In the work, EOS is obtained from steel manufacturing plants in South Korea and the engineering properties are evaluated for EOS and the cement mortar with EOS, respectively. From the tests, EOS is mainly made up of CaO, SiO₂, and FeO with 18.2% of larnite which has a crystal structure of β-C₂S with similar cement mineral. EOS mortar shows an increasing compressive strength with more EOS content, which is affected by a considerable amount of larnite (β-C2S) in EOS. The EOS based mortar with ERS (Electric Arc Furnace Reduction Slag) shows unsatisfactory results over the criteria for rate of change, which implies that more consideration must be taken for the usage of the mixed ERS and EOS for cement mortar due to swelling effect of ERS on dimensional stability.

A steel damper column is an energy-dissipating member that is suitable for reinforced concrete (RC) buildings and multistory housing. To assess the seismic performance of buildings with steel damper columns, the peak displacement of the whole building and the energy dissipation demand of the dampers must be evaluated. This article proposes an energy-based prediction procedure for the peak and cumulative response of an RC frame building with steel damper columns. The proposed procedure considers two energy-related seismic intensity parameters, namely the maximum momentary input energy and the total input energy. The peak displacement is predicted considering the energy balance during a half cycle of the structural response, using the maximum momentary input energy. The energy dissipation demand of the dampers is then predicted considering the energy balance during a whole response cycle using the total input energy. The local responses (e.g., peak drift, maximum plastic rotation of beams, maximum shear strain, and energy dissipation demand of dampers) are predicted using pushover analysis. Numerical analysis results for 8- and 16-story RC buildings show that the proposed prediction method achieves satisfactory accuracy.

In article questions of development low-waste technologies of processing of steel-smelting slag are considered, gland allowing by extraction and its connections from steel-smelting slag to receive additional raw materials for production became, and the remains to use in building industry. Studying of gravitational methods of enrichment of steel-smelting slag and heat treatment the ore-fuel of pellets is the basis for work. Proceeding from it, in work modern physic-mechanical, chemical and physical and chemical methods of researches (UV-spectroscopy, electronic microscopy, the granulometric analysis) are used.

In the realm of metal steel and iron manufacturing, there is a constant drive to optimize production efficiency and enhance the quality of the final products. This abstract explores a paradigm shift in this industry through the utilization of Computational Fluid Dynamics (CFD) as a powerful tool for achieving these goals .The study focuses on various critical aspects of the manufacturing process. Firstly, it delves into three-phase processes such as slag and gas entrainment in liquid steel, which have a significant impact on the overall product quality. Understanding and optimizing these processes is crucial to ensure the desired chemical composition and physical properties of the final metal.The abstract investigates the role of CFD in vacuum degassing, a process that plays a pivotal role in removing impurities, such as hydrogen and oxygen, from the liquid steel. By leveraging CFD to simulate and analyze the fluid flow patterns, researchers and engineers can design more efficient vacuum degassing systems, leading to improved product purity and reduced waste.Another crucial aspect explored in this abstract is the alloy melt and mixing process. By employing CFD simulations, researchers can gain insights into the movement of different alloy components and optimize their distribution within the melt. This aids in achieving the desired alloy composition, ensuring uniformity, and enhancing the mechanical properties of the final product.In addition, the study delves into the movement and flotation of inclusions, which are unwanted impurities present in the metal. CFD can be utilized to model and analyze the behavior of these inclusions, enabling engineers to design efficient strategies for their removal, thereby enhancing the purity and integrity of the final product.Moreover, the abstract considers the impact of melt temperature losses, which can occur during different stages of the manufacturing process. By employing CFD, it becomes possible to understand and mitigate these temperature losses, leading to improved energy efficiency and better control over the manufacturing parameters.Part 1 of this abstract critically evaluates the use of CFD in iron making, analyzing its benefits and limitations. It highlights how CFD can aid in process optimization, improving the understanding of complex phenomena involved in iron making, and ultimately leading to enhanced production efficiency.Part 2 focuses on the application of CFD in steel making and steel operation. It explores the fluid flow dynamics during different stages of steel production, including refining, casting, and rolling. By leveraging CFD, engineers can optimize these processes, leading to improved product quality, reduced defects, and increased productivity.This abstract demonstrates the transformative potential of Computational Fluid Dynamics in metal, steel, and iron manufacturing. By utilizing CFD as a tool to model and analyze complex fluid flow phenomena, researchers and engineers can revolutionize the production process, maximizing efficiency, and ensuring high-quality end products.

The study examines the behavior of the Mechanically Stabilized Earth (MSE) wall using available reinforcement materials in Danang, Vietnam. The MSE was reinforced by the self-fabricated galvanized steel grids using CB300V steel with 3 cm ribs. The backfill soil is a sandy clay soil from the local area with a low cohesion. A full-scale model with full instrumentation was installed to investigate the distribution of tensile forces along the reinforcement layers. The highest load that caused the wall to collapse due to internal instability (reinforcement rupture) was 302 kN/m2, which is 15 times the design load of 20 kN/m2. The failure surface within the reinforced soil had a parabolic sliding shape which is similar to the theoretical studies. At the failure load level, the maximum lateral displacement at the top of the wall facing was small (3.9 mm) which is significantly lower than the allowable displacements for the retaining wall. Furthermore, a numerical model using FLAC software was applied to simulate the performance of the MSE wall. The modeling results are in good agreement with the physical model. Thus, the self-fabricated galvanized steel grids could be confidentially used in combination with the local backfill soil for the MSE walls.

The steel damper column is an energy-dissipating member that is suitable for reinforced concrete (RC) buildings, and those used for multistory housing in particular. However, the effectiveness of steel damper columns may be affected by the behavior of surrounding members, and this effect can be severe in the case of seismic sequences. This article investigates the nonlinear response of building models having an RC moment-resisting frame (MRF) with and without steel damper columns under seismic sequences. The applicability of the concept of the momentary energy input to the prediction of the peak response of RC MRFs with damper columns under seismic sequences is also investigated. The main findings of the study are summarized as follows. (1) The peak response of RC MRFs with damper columns subjected to sequential accelerations is similar to the peak response obtained considering only the mainshock, whereas the cumulative strain energy of RC MRFs accumulates more for sequential accelerations. (2) The steel damper column is effective in reducing the peak and cumulative responses of RC MRFs in the case of sequential seismic input. (3) The relation of the hysteretic dissipated energy during a half cycle of the structural response and the peak displacement of the first modal response can be properly evaluated using the simple model proposed in this study.

The global steel industry is a major contributor to greenhouse gas emissions, and the adoption of green hydrogen in Direct Reduced Iron (DRI) production has the potential to significantly reduce CO2 emissions and support climate targets. This review explores the environmental, economic, technological, and social implications of using green hydrogen in DRI processes. The findings suggest that green hydrogen can reduce emissions by up to 90% compared to traditional methods, enhance energy security, and stimulate local economic development. However, high initial costs, energy efficiency concerns, and social acceptance issues remain significant barriers. The review also highlights the importance of integrating carbon capture and storage technologies, addressing logistical challenges, and considering the geopolitical implications of a shift towards green hydrogen. Green hydrogen presents a promising solution for decarbonising the steel industry but continued research, investment in infrastructure, and strategic planning are essential to overcome the challenges and drive widespread adoption.

Long-span steel structure trusses are widely used in factory buildings, but with the growth of service time and the increase of dynamic load fatigue, a considerable part of the long-span truss with dynamic load appears serious transverse cracks at the bottom of the middle span and oblique deformation of the abdomen in the operation process. The U-shaped cracks at the bottom and belly, as well as the mid-span down deflection of the main truss, reduced the functional function of the factory building truss structure, and had to limit the original crane load, which affected the normal safety and durability of the structure. Therefore, the application principle of the variable axial force cable system in the long-span factory building truss structure and 3D3S software modeling [1] were used. Analyzing and studying the reinforcement method of large-span powerhouse truss can provide practical experience for subsequent similar projects. In view of the above phenomenon, the large-span powerhouse trusses of Hongcheng Powerhouse 1 and No.2 located in Tonglu, Zhejiang Province are used as the research object, and the variable axial force cable method is proposed to strengthen and lift the load. Considering the span of large-span powerhouse truss, the cable system with 22m controlling force of 400kN is proposed to be selected for powerhouse 1, and the cable system with variable axial force of 24m is proposed to be selected for Powerhouse 2. The force model of large-span truss is established by using the finite element method commonly used to analyze the force of truss. Under two working conditions, The influence of reinforcement effect is analyzed and compared from three aspects: stiffness, bearing capacity and stability. And the phenomenon of uneven stress distribution is analyzed. The stress distribution characteristics of each node are understood by simulating the most disadvantageous node plates with the greatest internal force before and after reinforcement.

In view of the limitations of the existing optimization method of suspender cable force, in order to improve the stress of suspender under completion state and avoid frequent adjustment of cable force and grid beam elevation during construction, a new method of cable force optimization is proposed. The article takes the longest large span arch bridge in the world, Pingnan Third Bridge, a Concrete-filled steel tube (CFST) arch bridge with a span of 575m as the engineering background combined with the finite element analysis and multi-objective optimization method. One cable force optimization method that suspender “Real-time correction during construction, in the process variable optimal and results reliable” during panel girder lifting of long span CFST arch bridges is clarified. Taking the panel girder weight and displacement during the construction as parameter variables, the displacement and unevenness of the panel girder under completion state as constraint conditions, the displacement and cable force during the hoisting construction as the objective equation, through the optimization of the objective equation, the suspender cable force and dis-placement of each hoisting section are calculated. The results show that it is feasible to introduce the optimization theory into the cable force optimization when lifting the panel girder. the segment displacement variation is minimized to meet the destination. The cable force distributed evenly under completion state of the bridge that further making sure the completion state satisfies the requirements. No repeating iteration is needed, thus avoiding cumberso me calculation, getting cable force once. With higher optimization efficiency and better effects, the method provides high value for the cable force calculation of same type bridge suspender construction and for guiding construction.

The dilatometer curves of continuous cooling transformation of 12Mn steel were measured with Formastor-FⅡthermal mechanical simulator．The steel's undercooled austenite phase continuous cooling transformation curves ( CCT curves) were established by means of the dilatometer method and the metallographic-hardness measurement method． The effect of cooling rate on microstructure and hardness of the steel was studied． CCT curve of test steel was simulated by JMatPro. The results show that the Ac1 and Ac3 of the experimental steel are 692 ℃ and 855 ℃ ; the microstructure obtained is made of ferrite，pearlite and bainite．The ferrite transformation and pearlite transformation occur at a slower cooling rate，in which the ferrite is dominant. When the cooling rate is greater than 4.25 ℃ / s bainite transformation happens．As the cooling rate increases，microstructure or grains become finer．The hardness of the tested steel with increasing cooling rate shows a trend of first fast increase and soon decrease．The simulation results are consistent with the measured CCT law. The high temperature mechanical properties of 12mn steel round billet were tested by gleeble-1500d thermal / mechanical simulator. The tensile strength, reduction of area and stress-strain curves of the billet were obtained in the range of 600-1300 ℃.

Steel damper columns (SDCs) are energy-dissipating members that are suitable for reinforced concrete (RC) moment-resisting frames (MRFs) and those often used for multistory housing. In a previous study, an energy-based prediction procedure for the peak and cumulative response of an RC frame building with SDCs was proposed. In this procedure, the accuracy of the equivalent velocity of the maximum momentary input energy (V_ΔE1^*)–peak equivalent displacement (D₁^*_max) relationship is essential for improved prediction. In this article, the seismic capacity curve (V_ΔE1^*–D₁^*_max relationship) of RC MRFs with and without SDCs is evaluated using incremental critical pseudo-multi impulse analysis (ICPMIA). In the ICPMIA, which is based on a study by Takewaki and coauthors, the structure is subjected to various intensities of critical pseudo-multi impulsive lateral force. An ICPMIA of four 8- and 16-story RC MRFs with and without SDCs is performed to obtain their structural behaviors under various intensities of pulsive input. Then, the seismic capacity curve obtained from the ICMPIA results are compared with the predicted results based on the simplified equations. The main findings of this article are as follows. (i) The seismic capacity curve of RC MRFs without SDCs strongly depends on the number of impulsive lateral forces (N_p). As N_p increases, the seismic capacity decreases. The predicted seismic capacity curve severely underestimates that obtained from the ICMPIA in the case of large N_p. This trend is notable when the level of pinching behavior in the RC members is severe. (ii) In the case of an RC MRF with SDCs, however, the influence of N_p on its seismic capacity curve is small. The predicted seismic capacity curve agrees very well with that obtained from the ICMPIA. The influence of the level of pinching behavior in RC members on the seismic capacity curve is small.