The electromagnetic inference is an issue from decades, where working for a better shielding material is still on-going. The purpose of this study is to review the existing methods in the formation of graphene, metal and polymer-based composites. Study indicates that in graphene and metal-based composites, the utilization of alternating deposition method showed the highest shielding effectiveness, whereas, in polymer-based composite, the utilization of chemical vapor deposition method showed highest shielding effectiveness. However, this review reveals that still there is a gap in the literature in terms of the selection of the method. Although there are various available methods which researchers adopt as per their convenience, none of the studies makes a comparison of the methods to form a similar composite. Therefore, as a future gap researcher needs to adopt various methods to form a single composite and then make a comparison of shielding effectiveness. This act will be useful for future researchers to select the appropriate method.

HPV51 belongs to group I high-risk HPV (hrHPV) genotypes with a high prevalence of infection in numerous epidemiological studies, although its occurrence varies across geographical regions. To better understand the presence of variants and genetic variation of HPV51, this study aimed to perform a phylogenetic analysis of the E6, E7 and L1 regions to detect the hrHPV variants circulating in women referred to colposcopy in two different Italian regions (Lombardy and Sardinia). Cervical samples were tested using Anyplex™ II HPV HR Detection. HPV51 positive samples were further analysed using previously described PCR protocols to obtain sequences of E6, E7 and L1. A positivity rate for HPV51 of 7.4% (26/351) and 13.6% (11/81) was found in Lombardy and Sardinia, respectively. The majority (34 out of 35) of the analyzed sequences clustered into the A lineage and only one sequence was grouped into B lineage. L1 capsid gene showed the presence of different mutations but none under positive selective pressure. Three nucleotide polymorphisms T6311G, A6312T and G6313A related to the two aminoacidic mutations V264G and G265S were found among all analysed sequences. This study contributes to implement data regarding the molecular epidemiology of HPV but additional analysis on a larger number of sequences is necessary to better understand the role of HPV variants in cervical lesions development.

Emphasizing the importance of acoustic attenuation in maintaining compliance with stringent noise regulations and enhancing workplace safety, the analysis covers the theoretical and practical aspects of sound attenuation in a turboengine testing stand. This paper presents a preliminary analysis and also an evaluation of a procedure for projecting a noise attenuator for industrial application and especially for turboengine test stands. While primarily focusing on the static acoustic behavior of the attenuator, considerations were also made regarding flow dynamics, Mach number-dependent attenuation, pressure drop, and self-generated noise aspects to provide a comprehensive perspective in selecting the optimal design configuration. The study investigates different calculation methods for assessment of the noise reduction for linear and staggered baffles, applied on a scaled reduced model of attenuator. Thus, the critical parameters and projecting requirements necessary for effective noise reduction in high-performance turboengine testing environments will be evaluated in a down-scaled model. Key factors examined include the selection of design parameters and configurations from various options. Advanced computational methods, like analytic and finite element analysis (FEM) are utilized to predict the acoustic performance and identify potential design optimizations. Experimental validation is performed to corroborate the simulation results, ensuring the reliability and efficiency of the attenuator. The findings indicate that a well-designed sound attenuator module can significantly reduce noise levels without compromising the operational performance of the turboengine inside a test cell.

Monkeypox (mpox) caused by the monkeypox virus (MPXV) is currently the most common orthopoxvirus (OPXV) zoonotic disease. Since 2022, a multi-country outbreak of mpox has been reported with atypically rapid human-to-human transmission. The present work aimed to investigate the frequency of MPXV and OPXV DNA detection in different clinical materials taken at acute and convalescent phases of the infection in Bulgarian patients. A total of 181 clinical samples from 42 Bulgarian patients with possible mpox infections were tested. Screening for MPXV DNA (F3L gene) and OPXV DNA (rpo18 gene) were performed by real-time PCR assays. Of all tested patients six (14%) were confirmed with mpox infection. MPXV DNA was detected in 23/181 (12,71%) and OPXV DNA in 20/181 (11,05%) clinical samples. All confirmed patients were men who have sex with men, aged 23 to 44 (at an average age of 35,17±7,91 years) and two of them were HIV positive. The commonest clinical features of patients were fever (5/6), vesicular-pustular rash: perianal (6/6), penile (4/6), and limbs (4/6). MPXV DNA was found with the greatest frequency in specimens of vesicle contents and nasal/oropharyngeal swabs in 6/6 and 5/6. OPXV DNA mainly was detected in vesicle contents (6/6), nasal/oropharyngeal swabs (4/6), and urine (4/6). In the collected follow-up samples, MPXV DNA was detected in the highest percentage in the specimen's vesicle contents (6/6) and urine (6/6) and not demonstrated in samples of feces and saliva. The laboratory surveillance of MPXV is critical to contain the outbreak and to elucidate the new fast transmission of the virus.

Vertical-axis wind turbines (VAWTs) are receiving more and more attention as they involve simple design, cope better with turbulence and are insensitive to wind direction which has a huge impact on the cost since the yaw mechanism is not needed. However, VAWTs still suffer from low conversion efficiency. As a results tremendous efforts are exerted to improve its efficiency which mainly focus on two methods regardless of whether the study is a CFD simulation or a field test or lab test experiment. An active approach which involves the modification of the rotor itself such as the blade design, angle, trailing and leading edges, inner blades, chord thickness, contra-rotating rotor, etc. While the second approach involves passive techniques where the flow is directed to optimally face the downwind rotor by mounting a guiding vane such as a diffuser or other shapes at the upwind position of the rotor. Among all techniques undertaken, the CRWT rotor technique seems to be the most effective with an output even comparable to that of Horizontal Axis Wind Turbines (HAWT), while the Savonius rotor received more attention compared to other designs of VAWTs. Apart from technological issues, it was also suggested that geographical issues such as proper site siting of the wind turbine rotor at a particular location where a uniform flow could be guaranteed is of paramount importance to ensure an effective conversion capacity of wind turbines.

Lily tepals have a short lifespan. Once the tepals senesce, the ornamental value of the flower is lost. Some cultivars have attractive purple ovaries and fruits which greatly enhance the ornamental value of Asiatic hybrid lilies. However, little is known about the molecular mechanisms of anthocyanin biosynthesis in Asiatic hybrid lily ovaries. To investigate the transcriptional network that governs purple ovary coloration in Asiatic hybrid lilies, we obtained transcriptome data from green ovaries (S1) and purple ovaries (S2) of Asiatic ‘Tiny Padhye’. Comparative transcriptome analysis revealed 4228 differentially expressed genes. Differential expression analysis revealed that nine unigenes including four CHS genes, one CHI gene, one F3H gene, one F3′H gene, one DFR gene, and one UFGT gene were significantly up-regulated in purple ovaries. One MYB gene, LhMYB12-Lat, was identified as a key transcription factor determining the distribution of anthocyanins in Asiatic hybrid lily ovaries. Further qPCR results showed unigenes related to anthocyanin biosynthesis were highly expressed in purple ovaries of Asiatic ‘Tiny Padhye’ at stages 2 and 3, while they showed an extremely low level of expression in ovaries of Asiatic ‘Yellow Pixels’ during all developmental stages. In addition, shading treatment significantly decreased pigment accumulation by suppressing the expression of several unigenes related to anthocyanin biosynthesis in ovaries of Asiatic ‘Tiny Padhye’. These results could further our understanding of the molecular mechanisms of anthocyanin biosynthesis in Asiatic hybrid lily ovaries.

Background: Skin is exposed to ultraviolet radiation (UV) and air pollution and recent works demonstrated these factors have additive effects in the disturbance of skin homeostasis. Nuclear factor erythroid 2-related factor 2 (Nrf2) and aryl hydrocarbon receptor (AHR) appears appropriate targets in the management of combined environmental stressors. The protective effects of Silymarin (SM), an antioxidant and anti-inflammatory complex of flavonoids, were evaluated. Methods: Reactive oxygen species (ROS) and interleukin 1-alpha (IL-1a) were quantified in UV+urban dust stressed reconstructed human epidermis (RHE) treated with SM. Gene expression study was conducted on targets related to AHR and Nrf2. SM agonistic activity on cannabinoid receptor type 2 (CB2R) was evaluated on mast cells. Clinical study quantified the performance of SM and cannabidiol (CBD), in skin exposed to solar radiation and air pollution. Results: SM decreased morphological alterations, ROS and IL-1a in UV+urban dust stressed RHE. AHR and Nrf2 related genes were upregulated that control antioxidant effector and barrier function. Interleukin 8 gene expression was decreased. Clinical study confirmed SM to improve homogeneity and perceived well-being of urban skins exposed to UV, outperforming CBD. SM activated CB2R and release of β-endorphin from mast cells. Conclusions: SM provides protection of skin from oxidative stress and inflammation caused by two major factors of exposome and appears mediated by AHR-Nrf2. SM activation of CB2R opens a new understanding of SM anti-inflammatory properties.

Entropy generation, formulated by combining the first and second laws of thermodynamics with an appropriate thermodynamic potential, emerges as the difference between a phenomenological entropy function and a reversible entropy function. The phenomenological entropy function is evaluated over an irreversible path through thermodynamic state space via real time measurements of thermodynamic states. The reversible entropy function is calculated along an ideal reversible path through the same state space. Entropy generation models for various classes of systems—thermal, externally loaded, internally reactive, open and closed––are developed via selection of suitable thermodynamic potentials. Here we simplify thermodynamic principles to specify convenient and consistently accurate system governing equations and characterization models. The formulations introduce a new and universal Phenomenological Entropy Generation (PEG) theorem. The systems and methods presented––and demonstrated on grease degradation, battery charging and discharging, metal fatigue and pump flow––can be used for design, analysis, and support of diagnostic monitoring and optimization.

This article is devoted to overcoming the contradiction between the problem of maximizing the extraction of wind energy as the goal of optimizing wind turbines, and the use of traditional methods based on criteria for the aerodynamic quality of the blades. A modified technique is considered in which the optimization criterion is the directly extracted flow power. It is based on pulse theory methods that use specific power as an optimization criterion. A comparative analysis of the energy efficiency of different types of turbines is carried out, and the effects of blade inversion are considered. A method for calculating multi-rotor turbines based on the concept of uniform power distribution is presented. The compatibility of proprietary and traditional methods is considered by comparing the results of numerical experiments with calculated and experimental data from sources. Optimization computational algorithms generate data from numerical experiments and determine optimal parameter configurations for the turbines under consideration. It is shown that orthogonal Darrieus turbines in high-speed mode provide energy efficiency comparable to collinear turbines, and multi-rotor turbines with power uniformly distributed over the working section are not inferior in energy efficiency to basic turbines, with linear blade velocities halved.

A significant increase in persimmon production, combined with a higher percentage of fruits intended for export, led to the need to adapt post-harvest technology to ensure that the fruits reach the end consumer in optimal condition. Persimmon is a climacteric fruit, so the respiratory rate and ethylene production regulate its ripening during storage. Depending on the variety, it can be tart or impatient (initially). During mass harvesting, the pulp of persimmon, regardless of its variety, is usually very hard, but then it softens quickly, which creates problems during transportation. The fruit pulp of tart varieties of persimmon is usually lighter than that of tart varieties, but there are fewer filamentous fibers in the pulp of tart varieties that support its structure, therefore, during post-harvest aging, seedless astringent fruits soften faster than less tart fruits with 1-2 or more seeds. In addition, there are many intermediate varieties that change their food-tasting and technological properties depending on the degree of pollination in a single year. This encourages farmers to adhere to various strategies to reduce post-harvest losses. Persimmons are usually sold fresh or dried in the markets. In this article, we sought to compile an up-to-date and brief overview of the latest achievements in the persimmon drying technique, which may arouse interest among farmers and entrepreneurs seeking to implement their projects in this field of production activity.

In this paper, different cryptography algorithms were reviewed, and their relative merits were discussed. Symmetric and asymmetric cryptography algorithms were compared for time and space efficiencies. These experiments were run to measure the execution time and the memory footprints of various algorithms to understand the implications of their real-life applications. In the experiment performed, it was observed that elliptic curve cryptography was the most efficient in terms of encryption/decryption time, as well as memory usage.

This paper addresses the issues of methodological problems and limitations regarding measuring values. A short scan review of values measurement methods from psychological and ethnobotanical approaches was made to enumerate some of those shortcomings. A new methodological approach, named Kab’s Value Survey (KVS) was proposed and compared with other well adopted methods based on some important criteria to assess its suitability, uniqueness and novelty. The results of the comparisons shows that KVS for its considerations to the theoretical explanations distinguishes itself over other methods of value measurement in the sense that the methodological approach employed is more broad in scope and applications, simple, specific and reliable in terms of instruments for data collection, psychometric data analysis, and of course data presentation. The method however solved some of the criticized limitations that exist in other well adopted methods of values measurement from psychological and ethnobotanical perspectives.

Continuation methods are presented that are capable of treating frequency-domain flutter equations including multiple nonlinearities represented by describing functions. A small problem demonstrates how a series of continuation processes can find all limit-cycle oscillations within a specified region with a reasonable degree of confidence. Curves of the limit-cycle amplitude variation with velocity, indicating regions of stability and instability with colors give a compact view of the nonlinear behavior throughout the flight regime. A continuation technique for reducing limit-cycle amplitudes by adjusting various system parameters is presented. These processes are economical enough to be a routine part of aircraft design and certification.

Continual learning, a crucial facet of machine learning, involves the perpetual acquisition of valuable insights from incoming data, sans the necessity for full dataset access. Esteemed as a fundamental goal in artificial intelligence, continual learning grapples with an enduring challenge—catastrophic forgetting. A proficient model must exhibit adaptability for new data assimilation and robustness to retain existing knowledge. Class-incremental learning (CIL) aids the gradual integration of knowledge from newly introduced classes, forming a universal classifier. However, directly training the model with fresh class instances triggers a problem—forgetting distinguishing features of prior classes, causing a performance decline. Addressing such issues in machine learning, this survey aims to delineate significant challenges, outcomes, and recent advancements, including our contributions to CIL techniques, especially in image classification.

We compare the well known Rayleigh-Ritz variational method (RRVM) with a recently proposed approach based on supersymmetric quantum mechanics and the Gram-Schmidt orthogonalization method (SSQMGS). We apply both procedures to a particular class of double-well harmonic oscillators that had been conveniently chosen for the application of the latter approach. The RRVM eigenvalues converge smoothly from above providing much more accurate results with less computational effort. Present results show that the unproved SSQMGS upper bounds do not hold.

Suppose G is a graph with vertex-orbits O1,1 O2, . . . ,Ot, and jOi j denotes the cardinallity of Oi. Then OG (x) = åt 2 i=1 xjOi j is called as orbit polynomial. It is well-known that this polynomial 3 has a unique positive zero d in the interval [0, 1]. The aim of this paper is to study the specific 4 properties of this polynomial and then we determine the location of this root for several classes of 5 complex networks to compare with other graphical measures. Besides, we compare the unique 6 positive zero measure with several well-known centrality graph measures.

In this work, we adapt the fine-tuning algorithm of the Naïve Bayesian (FTNB) classifier to make it more suitable for imbalanced datasets. In particular, we boost misclassified instance probability terms by an amount that is disproportional to the harmonic mean of actual and predicted classes. The intuition is that discriminative attributes when the instance is misclassified would have small probability term pair values in both the actual class due to data scarcity and the predicted class due to weak correlation. Conversely, if both values are relatively high, then the attribute has good data coverage (support) and it should not be a cause for misclassification. Since the harmonic average is dominated by the smaller value and we have an imbalanced dataset, we should enact a large update if both or either term probabilities of actual and predicted classes are small. We used several benchmark datasets (60 different balanced and imbalanced datasets) to determine if the poor performance of the NB classifier is due to the scarcity of data and compared the performance of the proposed algorithm with NB, original FTNB, and other relatively new SOTA Ensemble Imbalanced Classifiers. Our empirical results reveal that the new proposed algorithm significantly outperforms all other classifiers.

This paper introduces a multi-class hand gesture recognition model developed to identify a set of defined hand gesture sequences in two-dimensional RGB video recordings. The work presents an action detection classifier that looks at both appearance and spatiotemporal parameters of consecutive frames. The classifier utilizes a convolutional-based network combined with a long-short-term memory unit. To leverage the need for a large-scale dataset, the model uses an available dataset to then adopt a technique known as transfer learning to fine-tune the model on the hand gestures of relevance. Validation curves performed over a batch size of 64 indicate an accuracy of 93.95% (± 0.37) with a mean Jaccard index of 0.812 (± 0.105) for 22 participants. The presented model illustrates the possibility of training a model with a small set of data (113,410 fully labelled frames). The proposed pipeline embraces a small-sized architecture that could facilitate its adoption.

The present paper deals with a class of even entire functions of order $\rho =1$ and genus $\vartheta =0$ of the polynomials form, \[ \sum\limits_{m=0}^\infty {\frac{\left( {-1} \right)^m\Phi ^{\left( {2m} \right)}\left( 0 \right)}{\Gamma \left( {2m+1} \right)}x^{2m}} =\Phi \left( 0 \right)\prod\limits_{k=1}^\infty {\left( {1-\frac{x}{\ell _k }} \right)} , \] where $\Phi\left( 0 \right)\ne 0$, real numbers $x$, nonnegative integers $m$, and $\ell _k \ne 0$ are all of the nonzero roots with $\sum\limits_{k=1}^\infty {1/\left| {\ell _k } \right|} <\infty $ and natural numbers $k$. We provide an efficient criterion for the polynomials with only real zeros. We also prove that the conjecture of Jensen is our special case.

The asymptotic dynamics of the classes of rational difference equations (RDEs) of third order defined over the positive real-line as $$\displaystyle{x_{n+1}=\frac{x_{n}}{ax_n+bx_{n-1}+cx_{n-2}}}, \displaystyle{x_{n+1}=\frac{x_{n-1}}{ax_n+bx_{n-1}+cx_{n-2}}}, \displaystyle{x_{n+1}=\frac{x_{n-2}}{ax_n+bx_{n-1}+cx_{n-2}}}$$ and $$\displaystyle{x_{n+1}=\frac{ax_n+bx_{n-1}+cx_{n-2}}{x_{n}}}, \displaystyle{x_{n+1}=\frac{ax_n+bx_{n-1}+cx_{n-2}}{x_{n-1}}}, \displaystyle{x_{n+1}=\frac{ax_n+bx_{n-1}+cx_{n-2}}{x_{n-2}}}$$ is investigated computationally with theoretical discussions and examples. It is noted that all the parameters $a, b, c$ and the initial values $x_{-2}, x_{-1}$ and $x_0$ are all positive real numbers such that the denominator is always positive. Several periodic solutions with high periods of the RDEs as well as their inter-intra dynamical behaviours are studied.

This article is an anthropology study on how western-style coffee culture influences Indonesian coffee culture and eventually develops a new localized coffee culture. Immense development of such worldwide coffee franchise as Starbucks affects local community's coffee culture, particularly the middle class. This new wave is considered as an alternative lifestyle for those who are consumptive and seeking for leisure, dynamics, and identity. Broader than just the process of domestication or creolization, Indonesian new coffee culture has an element of “soft countering to” western coffee culture even though it still embraces some parts of the western styles. This phenomenon is referred to by the writer as the cultural encapsulation process or the process of substantial cultural resistance by drawing a line between the two coffee cultures with the intention of taking merely compatible elements.

The authors intend to establish new oscillation criteria for a class of generalized third order functional difference equation of the form \begin{equation}{\label{eq01}} \Delta_{\ell}\left(a_2(n)\left[\Delta_{\ell}\left(a_1(n)\left[\Delta_{\ell}z(n)\right]^{\beta_1}\right)\right]^{\beta_2}\right)+q(n)f(x(g(n)))=0, ~~n\geq n_0, \end{equation} where $z(n)=x(n)+p(n)x(\tau(n))$. We also present sufficient conditions for the solutions to converges to zero. Suitable examples are presented to validate our main results.

Heavy metal pollution poses a significant threat to ecosystems and human health worldwide. In response to this pressing issue, bioremediation has emerged as a promising approach for mitigating contamination. This paper adopts a bibliographic method to explore the key techniques and applications of bioremediation. Furthermore, we delve into the most prominent threats to human environmental health and the corresponding remediation methods. Additionally, we discuss the future trajectory of bioremediation research, with a particular focus on the integration of big data and machine learning technologies. These advanced methodologies hold great potential for enhancing the effectiveness and efficiency of environmental remediation efforts in the face of escalating pollution challenges.

As marine traffic is contributing to pollution and mostly have predictable route with repetitive load profiles, to reduce their impact on environment, hybrid system with proton exchange membrane fuel cells (PEMFC-s) and battery pack, is promising replacement. For this purpose, the numerical model of repowered existing vessel that have two diesel engines with 300 kWe is developed. The goal of this paper is to develop numerical model which analyzes and determine equivalent hybrid ship propulsion system for known traveling route. The developed numerical model consists of an interconnected system with PEMFC stack and battery pack as power sources. Numerical model is developed and optimized to meet minimal required power demand for successful route demand, which has variable loads and daily sails six-time same voyage- in total 54 nautical miles. The results have shown that equivalent hybrid power system consists of 300 kWe PEMFC stack and battery pack with 424 kWh battery and state of charge varying between 20 and 87%. To power this new hybrid power system, hydrogen tank of 7200 l holding 284.7 kg at pressure of 700 bar is needed, compared to previous system that spend 1524 kg of diesel and generate 4886 kg of CO2.

A hydrothermal technique with microwave heating (200 °C, 2 hours, 2 magnetrons, 2.45 GHz) was modified to obtain UV-C luminescent LaPO4: Pr3+ colloidal nanorods for the potential use in X-ray cancer theranostics. For further possible biofunctionalization, a compound of tartaric acid formed under basic conditions was used as a coating and stabilizing agent to provide colloidal properties to the surface of nanoparticles in basic to neutral aqueous media, which was confirmed by zeta potential measurements. In addition, the colloidal properties and clustering processes of synthesized LaPO4:Pr3+ nanorods in aqueous solutions with different pH values were studied in real time using a highly sensitive laser ultramicroscope operating according to the “light-sheet” scheme. A comparative analysis of the transmission electron microscopy, X-ray powder diffraction and high-energy spectroscopy showed the different effects of synthesis parameters on the morphological, crystalline and luminescent properties of the obtained nanorods. Through optimization of the synthesis parameters, stable aqueous solutions of m-LaPO4:Pr3+ nanorods with sizes less than 30 nm and an intensity of UV-C luminescence equal to 5-10% of the unmodified nanofibers were obtained.

The dynamic behaviour of a machine tool (MT) directly influences the machining performances. The adoption of lightweight structures may reduce the effects of undesired vibrations and increasing the workpiece quality. This paper aims to present and compare a set of hybrid materials that may be excellent candidate to fabricate the MT moving parts. The selected materials have high dynamic characteristics and capacity to damp mechanical vibrations. In this way, starting by the kinematic model of a milling machine that highlights the main critical factors, this study paper evaluates a number of prototypes made of Al Foam sandwiches (AFS), Al Corrugated sandwiches (ACS) and materials reinforced by carbon fibres (CFRP). A set of prototypes has been fabricated, represented the Z-axis ram of a commercial milling machine. The static and dynamical properties have been evaluated by using both FE simulations and experimental tests. The obtained results show that the proposed structures may be a valid alternative to the conventional materials of MT moving parts, increasing machining performances. In particular, the AFS prototype highlighted a damping coefficient that is 20 times greater than a conventional ram (e.g. steel). The CFRP structure is able to satisfy the machining requirements with a reduced weight of 48.5%, while the ACS prototype showed a good trade-off between stiffness and damping.

UV-Visible spectroscopy method has been developed for the analysis of Thiamine in biological and pharmaceutical product, based on a chromogenic derivatizing reaction using PDAB (P- dimethyl amino benzaldehyde) reagent. A Central Composite Design (CCD) design with response surface methodology was executed for optimization of experimental conditions of drug with a smaller number of experimental trials. Three independent factors, the concentration of PDAB, the volume of PDAB reagent, and volume of HCl, were used to construct a mathematical model and study the effects of these independent factors on responses as absorbance. The colored complex exhibits a Red shift with absorption maximum λmax at 425 nm, which was selected as the analytical wavelength. The drug seems to be linear, which was established via the regression analysis from 5-30 μgmL-1, with an R2 value of 0.998.The % RSD for intraday and interday precision was < 2%, with good recovery ranging from 95.02 to 101.43% with biological and pharmaceutical samples. LOD and LOQ of the developed method were found to be 1.51 μg mL-1 and 4.57 μg mL-1.This method can be used in routine analysis of pharmaceutical products containing aromatic primary amines along with an estimation of biological samples like urine, blood, sweat, faeces.

The hospital indoor environment plays a significant role in shaping the microbial exposures that humans encounter. Resistance to antibiotics is one of the mechanisms employed by bacteria to develop resilience against stress in indoor environments. The extensive usage of antibiotics has been a key factor in driving changes in the ecological function of antibiotic resistance genes (ARGs) and their acquisition by pathogenic bacteria. By integrating the 16S rRNA Illumina sequencing and high throughput-qPCR approaches with water and air dust samples across seven departments at Peking University Shenzhen Hospital, China, this study yielded intriguing findings regarding the department-specific variation, transmission, and correlation of bacteria, ARGs and MGEs within the hospital indoor environment. One notable observation was that the seasonal variation played a vital role in shaping the bacterial composition in the overall hospital indoor environment across seven studied departments. Nevertheless, a similar significant seasonal impact was only observed in the blood test room and emergency departments, rather than in the other five departments. Another intriguing finding was the correlation between ARGs and MGEs abundance. This correlation was evident in the overall hospital indoor environment, which was conversely not found in the emergency, pneumology and gynecology departments. Additionally, while there was no significant relationship that occurred between bacterial communities and ARGs/MGEs within the hospital, the gynecology department demonstrated a close link between bacterial communities and the presence of ARGs/MGEs. Notably, the gynecology department also stood out as an important source of bacteria and ARGs/MGEs for other departments. This study underscores the need for careful surveillance and monitoring of antibiotic resistance, particularly in Legionella spp. in man-made water systems. The findings also show the importance of monitoring and understanding the genetic elements such as Tp614 involved in gene transfer and recombination, as well as their impact on antimicrobial treatment efficacy.

Polycystic ovary syndrome (PCOS) is a common condition in reproductive-age women. Women with PCOS are at higher risk of pregnancy complications including gestational diabetes (GDM). The prevalence of PCOS and GDM varies according to the diagnostic criteria used. The mechanism for the occurrence of GDM in women with PCOS is still unclear. Materials &amp; Methods- A systematic search of the electronic database was done using keywords like PCOS, and GDM to include studies between April 2008 and March 2023 where uniform diagnostic criteria were used. Studies were excluded with high-risk of bias after the assessment of bias, and meta-analysis was done with relative risks and confidence intervals. Results &amp; Discussion-Out of 1896 search results, 95 were selected for full-text. The quality of the studies was scrutinized and a total of 28 studies were included as they fulfilled the inclusion criteria. The incidence of GDM in women with PCOS was found to be 10.55 % (2.9- 54.9%) from pooled data involving 1,280,245. The prevalence of PCOS in women diagnosed with GDM was found from pooled data of 36,351 women in retrospective studies to be 2.47% (1.5- 50.1%). Selection predominantly included cohort studies, most commonly from China. The meta-analysis reported the risk of GDM is higher in women with PCOS than in those without PCOS (HR: 1.59, 95% CI: 1.27–1.91, p &lt; 0.001). Family history of diabetes, ethnicity, pre-pregnancy BMI, insulin resistance, gestational weight gain, use of assisted reproductive techniques, and multifetal gestation were the risk factors for GDM in women with PCOS. Conclusion- The prevalence of GDM in patients with PCOS is high, but the causality is complex. The newer predictive models are promising in clarifying the causative relationships, yet use various parameters at different cut-offs. There is a need for the development of universally acceptable parameters for the early prediction of GDM in women with PCOS.

Background: Bariatric surgery (BS) has a significant impact on body composition (BC) and con-sequently may affect established sarcopenic obesity (SO) in candidate patients. The aim of this study is to assess the utility of muscle ultrasound (MUS) of rectus femoris thickness (RFT) for the evalua-tion of BC and skeletal muscle function in patients undergoing BS compared to bioimpedance analysis (BIA), dual-energy X-ray absorptiometry (DEXA) and dynamometry. On the other hand, we aim to demonstrate how MUS of RFT correlates better with the quality of life (Qol) in this population, likely because it enables the detection of regional quadriceps muscle sarcopenia, in comparison to the other mentioned methods. Methods: This is a prospective pilot study including 77 subjects (64.9% female, mean age: 53.2 ± 8.67 years) who underwent BS. Handgrip strength was measured using a dynamometer, fat-free mass index (iFFM) was assessed by BIA, appendicular muscle index (AMI) was calculated using DEXA and RFT was measured by MUS. Moreover, Homeostasis Model Assessment of Insulin Resintance (HOMA-IR) was calculated. All these measurements were conducted 1 month prior to BS and at the 12-month follow-up. QoL was as-sessed using the Moorehead-Ardelt questionnaire. Results: The mean BMI decreased by 12.95 ± 3.56 kg/m2 (p=0.001). Firstly, we observed positive correlation pre-surgery between HOMA and: RFT (r=0.27, p=0.02), iFFM (r=0.36, p=0.001), AMI (r=0.31, p=0.01) and dynamometer (r=0.26, p=0.02). In addition, we found correlation between RFT and iFFM (pre-surgical: r=0.31, p=0.01; post-surgical: r=0.25, p=0.05) and between RFT and lower extremities AMI post-surgical (r=0.27, p=0.04). Secondly, we observed significant reductions in iFFM, AMI and RFT (p=0.001), but not with dynamometer (p=0.94). Finally, a tendency to a positive correlation between QoL question-naire and RFT post-surgery (r=0.23, p=0.079) was observed. Conclusions: Our results suggest that RFT measured by MUS for the evaluation of SO and the follow-up after BS of these patients. Moreover, RFT can provide relevant information about regional sarcopenia and probably has an accurate correlation with QoL in comparison with the other methods.

Nowadays brushless DC motors (BLDCMs) are becoming indispensable components as the electrification revolution in the mobility industry is happening. Electric kick scooters, so-called e-scooters, are among these micro-mobility vehicles which are powered by these motors. Due to the uncertain and nonlinear features, the controller performance developed for these motors degrades. For these reasons, a chattering-reduced cascaded Sliding Mode Control (SMC) scheme to effectively track reference motor speed in the outer loop by eliminating torque ripples in the inner loop current control was designed. Field-oriented Control (FOC) methodology was used to implement the SMC in the BLDCM. An exponential reaching law algorithm was proposed for sliding surfaces of the inner and outer loop controllers. The suitability and performance of electric scooter-hub motors were analyzed in terms of traction control. A cascaded speed and torque controller produced significantly favorable results representing minimized torque and current ripples, and operation over a wide speed range.

Introduction: Cleft lip with or without cleft palate (CL/P) is the most common congenital face anomaly in the world of multifactorial etiology. Objective: To determine the prevalence and characteristics of cleft palate. To identify associated risk factors to guide prevention and/or prenatal detection for early intervention and better health outcomes. To assess the rehabilitation protocols after operations in cleft palate. Design: Retrospective descriptive and clinical study. Patients: One hundred and three children with cleft palate treated in the Department of Head and Neck Surgery Clinic for Children and Young Adults, Department of Clinical Pediatrics, University of Warmia and Mazury, were included in the study. Methods: Records evaluation was conducted regarding sex, cleft type, mother occupation, parents education, histories of cleft in any of parents. The data were analyzed using R (R core team 2021) and the ordinal logistic regression analyses. Results: Children of stressed mothers during pregnancy had 9.4 times higher odds of having bilateral cleft. While there was no evidence that children sex, order of birth, and body mass as well as risk of maternal toxicity at work or reporting infections or drugs toxicity had a significant effect on the dependent variable. Conclusions: Children of parents with cleft history and having low educated mothers had higher probability of bilateral cleft palate. Children of stressed mothers during pregnancy had higher odds of having bilateral cleft. In literature, there is a lack of reports about rehabilitation in different operations methods in children with cleft palates.

A new trend in cow's milk has emerged in the market called type A1 and A2 milk. These products have piqued the interest of both consumers and researchers. Recent studies suggest that A2 milk may have potential health benefits, which is why researchers are investigating this product further. It is interesting to note that the A1 and A2 milk types have area-specific characteristics compared to breed-specific characteristics. Extensive research has focused on milk derivatives obtained from cow’s milk, primarily through in vitro and animal studies. However, few clinical studies have been conducted in humans, and the results have been unsatisfactory. New molecular techniques for identifying A1 and A2 milk may help researchers to develop new studies that can clarify certain controversies surrounding A1 milk. It is essential to exercise extreme caution when interpreting the updated literature. It has the potential to spread panic worldwide and have negative economic implications. Therefore, this study aims to investigate the new aspects of A1 and A2 milk in different research areas and clarify some aspects regarding these two types of milk.

At present, farmland abandonment（FA）is a severe phenomenon in China, imposing a serious restriction on agricultural production. In this context, it is of great significance to explore the logical relationship between high-standard farmland construction (HSFC) and FA to optimize land resource allocation and guarantee national food security. Based on 838 samples of farmers in the main rice production area of the Yangtze River Basin in China, this paper employs the Tobit model, the mediating effect model, and the moderated mediating effect model to analyze the impact of HSFC on FA at the micro level. The results show that (1) HSFC inhibits FA, and FA proportion decreases by 1.14% for every 1% increase in HSFC proportion, and the robustness test and endogeneity treatment also yield consistent conclusions. (2) Agricultural socialization services (ASS) play a positive mediating role in the influence path. HSFC promotes farmers' purchase of ASS, which in turn inhibits FA. (3) The agricultural labor transfer distance (ALTD) plays a positive moderating role in the relationship between HSFC and FA. The farther the distance, the more likely HSFC can promote farmers' purchase of ASS and inhibit FA. The results provide enlightenment on how to precisely implement HSFC policy, that is, to inhibit FA by improving the construction of high-standard farmland and the post-construction management as well as protection system. Moreover, this study helps guiding the development of ASS and optimizing the institutional environment for agricultural labor transfer, creating conditions for agricultural scale management.

The most important plastic resins used for wire coating are Polyvinyl Chloride (PVC), Nylon, Polysulfone and Low-high density polyethylene (LDPE / HDPE). In this article,the coating process is performed using elastic-viscous fluid as a coating material for wire coating in a pressure type coating die. The elastic-viscous fluid is electrically conducted in the presence of an applied magnetic field. The governing non-linear equations are modeled and then solved analytically by utilizing an Adomian decomposition method (ADM). The convergence of the series solution is established. The results are also verified by Optimal Homotopy Asymptotic Method (OHAM). The effect of different emerging parameters such as non-Newtonian parameters α and β, magnetic parameter M and the Brinkman number Br on solutions (velocity and temperature profiles) are discussed through several graphs. Additionally, the current result also compares with the published work already available in the literature.

Base excision repair (BER) is a cellular process that removes damaged bases arising from exogenous and endogenous sources including reactive oxygen species, alkylation agents, and ionizing radiation. BER is mediated by the actions of multiple proteins that work in a highly concerted manner to resolve DNA damage efficiently to prevent toxic repair intermediates. During the initiation of BER, the damaged base is removed by one of 11 mammalian DNA glycosylases resulting in abasic sites. Many DNA glycosylases are product inhibited by binding to the abasic site more avidly than the damaged base. Traditionally apurinic/apyrimidinic endonuclease, APE1, was believed to help turnover the glycosylases to undergo multiple rounds of damaged base removal. However, in a series of papers from our laboratory we have demonstrated that UV-damaged DNA binding protein (UV-DDB) stimulates the glycosylase activities of human 8-oxoguanine glycosylase (OGG1), MUTY DNA glycosylase (MUTYH), alkyladenine glycosylase/N-methylpurine DNA glycosylase (AAG/MPG), and single-strand selective monofunctional glycosylase (SMUG1), between three-to-five-fold. Moreover, we have shown UV-DDB can assist chromatin decompaction facilitating access of OGG1 to 8-oxoguanine damage in telomeres. This review summarizes the biochemistry, single-molecule, and cell biology approaches that our group used to directly demonstrate the essential role of UV-DDB in BER.

The aim of this work was to test polyamines as potential natural substrates of the Acinetobacter baumannii chlorhexidine efflux protein AceI using near-UV synchrotron radiation circular dichroism (SRCD) spectroscopy. The Gram-negative bacterium A. Baumannii is a leading cause of hospital-acquired infections and an important foodborne pathogen. A. Baumannii strains are becoming increasingly resistant to antimicrobial agents, including the synthetic antiseptic chlorhexidine. AceI was the founding member of the recently recognised PACE family of bacterial multidrug efflux proteins. Using the plasmid construct pTTQ18-aceI(His₆) containing the A. Baumannii aceI gene directly upstream from a His₆-tag coding sequence, expression of AceI(His₆) was amplified in E. coli BL21(DE3) cells. Near-UV (250-340 nm) SRCD measurements were performed on detergent-solubilised and purified AceI(His₆) at 20 °C. Sample and SRCD experimental conditions were identified that detected binding of the triamine spermidine to AceI(His₆). In a titration with spermidine (0-10 mM) this binding was saturable and fitting of the curve for the change in signal intensity produced an apparent binding affinity (K_D) of 3.97 +/- 0.45 mM. These SRCD results were the first experimental evidence obtained for polyamines as natural substrates of PACE proteins.

Conventional flame retardant (FR) application processes for textiles involve aqueous processing which is resource intensive in terms of energy and water usage. Recent research using sol-gel and layer-by-layer chemistries, while claimed to be based on more environmentally-sustainable chemistry, still require aqueous media with the continuing problem of water management and drying processes being required. This paper outlines the initial forensic work to characterise commercially produced viscose/flax, cellulosic furnishing fabrics which have had conferred upon them durable flame retardant (FR) treatments using a novel, patented atmospheric plasma/UV excimer laser facility for processing textiles with the formal name - Multiplexed Laser Surface Enhancement (MLSE) system. This system (MTIX Ltd., UK), is claimed to offer the means of directly bonding of flame retardant precursor species to the component fibres introduced either before plasma/UV exposure or into the plasma/UV reaction zone itself, thereby eliminating a number of wet processing cycles. Nine commercial fabrics, pre-impregnated with a semi-durable, proprietary FR finish and subjected to the MLSE process have been analysed for their flame retardant properties before and after a 40 °C 30 min water soak. For one fabric, the pre-impregnated fabric was subjected to a normal heat cure treatment which conferred the same level of durability as the plasma/UV-treated analogue. TGA and LOI were used to further characterise their burning behaviour and the effect of the treatment on surface fibre morphologies were assessed. Scanning electron microscopy indicated that negligible changes had occurred to surface topography of the viscose fibres occurred during plasma/UV excimer processing.

The environment significantly impacts the life of bees and their feeding. This study aimed to investigate bee foraging using melissopalynological analysis and DNA metabarcoding in ​​intensive farming, reserved, and urbanized areas. The highest alpha diversity was observed in the reserved and in the intensive farming areas. The urbanized area has less diversity. In the intensive farming area predominated: Sinapis, Helianthus, and Fagopyrum; in the reserved area: Melilotus, Helianthus, and Brassica. In the urbanized area garden plants: radish (Raphanus sativus) and cucumber (Cucumis hystrix) and agricultural plants: soybean (Glycine max) and melon (Cucumis melo) were often found. The most significant agreement was between the rbcL and the melissopalynological analysis. The ITS2 revealed equal matches with both rbcL and melissopalynology but this marker missed or underestimated some genera. Trifolium pretense and Brassica nigra, were identified simultaneously by three analyses. Species Convolvulus arvensis, Melilotus officinalis, Echium vulgare, Brassica rapa, Helianthus divaricatus, and Onobrychis viciifolia were found in all ecological areas. Imperfect databases put some limits for identification of some taxa using metabarcoding. Further research and expansion of plant databases is needed. Studying the food preferences of bees in different environmental conditions and landscapes is necessary to develop measures to preserve their population.

The release profiles of methotrexate, an anticancer drug, from the monoolein liquid crystalline cubic phases were studied. The cubic phases were used either in the form of a lipidic film deposited onto a glassy carbon electrode surface or in the dispersed form of magnetocubosomes, which are considered a prospective hybrid drug delivery system. Commonly, cubosomes or liposomes are employed, but not in the case of toxic methotrexate, known to block receptors responsible for folate transport into the cells. The release profiles of the drug from the lipidic films were monitored electrochemically and described using the Higuchi model. They were also modified via changes in temperature; the release was faster, although deviating from the model when the temperature was increased. Magnetocubosomes - cubic phase nanoparticles containing hydrophobic magnetic nanoparticles placed in an alternating magnetic field of low frequency and amplitude, stimulated drug release from the suspension, which was monitored spectroscopically. These new biocompatible hybrid materials are very promising, allowing to control the release of the drug at the appropriate sites, but do require further investigations into their in vitro cytotoxicity and in vivo biodistribution.

Treating central giant cell granuloma (CGCG) is challenging due to high recurrence rates and variable therapy responses. This study examines the efficacy of various treatments in reducing CGCG recurrence. A literature review explored outcomes of surgical excision, curettage, intralesional corticosteroid injection, and adjuvant therapy, considering factors like lesion location, size, and histological features. Aggressive surgical techniques such as en bloc resection were found to potentially lower recurrence rates compared to conservative approaches. However, treatment should be tailored to individual patient needs. Further research is needed to confirm these findings and improve treatment strategies. A concise literature review was conducted using PubMed, MEDLINE, and Google Scholar, focusing on papers published from 1986 to 2024. Search terms included "central giant cell granuloma," "recurrence," "treatment modalities," and "surgical excision". Studies reporting recurrence rates and treatment outcomes for CGCG were analyzed. Twenty-nine studies were reviewed, including six studies on surgical excision and curettage, eight studies on intralesional corticosteroid injections, six studies on calcitonin therapy, five studies on interferon alpha therapy and four studies on the therapy with denosumab. Analysis indicated that aggressive surgical treatments like en bloc resection were associated with lower recurrence rates compared to conservative methods. Predictors of recurrence included lesion size (&gt;3 cm), location (mandible), and aggressive histopathological features. Aggressive surgical excision combined with nonsurgical methods may lower recurrence rates, while conservative techniques remain viable in some cases. Further prospective research is needed to validate these findings and enhance CGCG treatment options.

The oscillating heat pipe (OHP) is a new member in the family of heat pipes, and it has great potential applications in energy conservation. However, the fluid flow and heat transfer in the OHP as well as the fundamental effects of inner diameter on them have not been fully understood, which are essential to the design and optimization of the OHP in real applications. Therefore, by combining the high-speed visualization method and infrared thermal imaging technique, the fluid flow and thermal performance in the OHPs with inner diameters of 1, 2 and 3 mm are presented and analyzed. The results indicate that three fluid flow motions, including small oscillation, bulk oscillation and circulation, coexist or, respectively, exist alone with the increasing heating load under different inner diameters, with three flow patterns occurring in the OHPs, viz. bubbly flow, slug flow and annular flow. These fluid flow motions are closely correlated with the heat and mass transfer performance in the OHPs, which can be reflected by the characteristics of infrared thermal images of condensers. The decrease in the inner diameter increases the frictional flow resistance and capillary instability while restricting the nucleate boiling in OHPs, which leads to a smaller proportion of bubbly flow, a larger proportion of short slug flow, a poorer thermal performance, and easier dry-out of working fluid. In addition, when compared with the 2 mm OHP, the increasing role of gravity induces the thermosyphon effect and weakens the 'bubble pumping' action, which results in a little smaller and bigger thermal resistances of 3 mm OHP under small and bulk oscillation of working fluid, respectively.

Acquired immunodeficiency syndrome (AIDS) has transitioned from a progressive, fatal disease to a chronic, manageable disease thanks to better defining of antiretroviral therapy, hence contributing to increased life expectancy. In parallel, a growing number of subjects without overt clinical signs of disease but living with chronic HIV infection (people living with HIV, PLWH) are experiencing early cardiovascular disease worldwide. However, a progressive increase in the prevalence of multiple comorbid diseases has been reported as these patients age, including cardiovascular disease (CVD). Cardiovascular mortality can be either directly related to the viral infection, a progressive reduction of response to the antiretroviral therapy, chronic inflammation or lifestyle-related. Cardiovascular ageing represents a relevant issue in the management of HIV-infected patients. Although the exact pathophysiological mechanism that leads PLWH to develop cardiovascular disease is not entirely understood, there is substantial evidence that they accumulate age-related conditions earlier than the general population. Furthermore, since the proportion of PLWH growing older than 50 years has progressively increased, this results in a complex interaction between disease-related pathophysiology and the exposition of a growing burden of cardiovascular risk factors. For this reason, we performed a systematic review of the genes most frequently associated with ageing in HIV-infected subjects, followed by a bioinformatic analysis to explore the biological impact of the genes related to ageing.

Rising obesity and associated multi-systemic complications amplify the health burden. Euphorbia kansui (EK) extract is clinically recognized for managing obesity. In human study, 240 obese individuals were categorized into two cohorts: those receiving solely herbal medicine (HM group), and those administered EK concomitantly with herbal medicine (EK group). An in vivo examination using C57BL/6-Lepob/Lepob mice elucidated mechanisms involving macrophages and gut microbiota, with associated metabolic advantages. The clinical study revealed a significant 7.22% body weight reduction during 91.55 average treatment days, and examined 16.71% weight loss at 300 days after treatment. In the whole subjects, 60.4%, 21.3% and 6.3% achieved weight reductions exceeding 5%, 10% and 15%, respectively. Impressively, the EK group exhibited superior weight loss compared to the HM group (EK: -7.73% vs. HM: -6.27%, p=0.012). The anti-obesity effect was positively associated with EK therapy frequency and herbal medicine duration. In vivo, EK significantly improved insulin sensitivity and mitigated infiltration of adipose tissue macrophages (ATMs) by modulating the CD11c+ and CD206+ subtypes. EK also correlated with increased Bacteroidetes and Firmicutes populations and reduced Proteobacteria and Verrucomicrobia. Consequently, EK is an effective adjunctive anti-obesity therapy offering metabolic benefits by modulating ATMs and gut microbiota profiles.

Cybercrime Threat Intelligence (CTI) allows us to change our actions from reactive to proactive in the fight against threat actors, and to make more informed, data-driven security decisions. Thus this study proposes the practical implementation of CTI in the Arab world. This study focuses on strengthening CTI by integrating Indicators of Compromise (IoCs) and collecting realistic security alerts from honeypot systems and open source intelligence. The collected data is stored in the Malware Information Sharing Platform (MISP), an open source platform that allows users to create and share IoCs with other organizations while staying informed about new threats. It features an intuitive interface for data analysis and threat identification, facilitating sharing, storage, and correlation of IoCs. Therefore, we leveraged MISP to generate IoCs based on the collected data and analyzed the results to identify potential cyber threats. The implemented platform aims to provide organizations with actionable information to prevent, detect and respond to cybercrime. This study presents a practical approach to strengthening CTI in the Arab world and provides an opportunity to strengthen the region’s security posture.

With a view to understand and resolve the complexity of the food matrix, ohmic technologies alone or in combination were extensively employed. In this sense, the newest developments and advances of proteomics, metabolomics, lipidomics whith their unique benefits could simplify and understand the link between physiological and pathological activities in biology, physiology, pathology, and food science and processing. This review aims to briefly introduce the basis of proteomics, metabolomics, lipidomics, then expansively review their impact on the assessment of meat quality and safety. Here, also, we discuss the application of proteomics, metabolomics, lipidomics for the authentication and adulteration of meat and meat derivatives from different sources, and provides some perspectives regarding the use of emerging techniques such as rapid mass spectrometry (MS) and non-invasive measurements for the analysis of meat quality and safety. This paper summarizes all significant investigation in these matters, and underlines the advances in analytical chemistry technologies and meat science areas. By emphasizing the requirement for additional examinations, this paper attempts a comprehensive knowledge of “foodomics” and their potential to improve their employment in meat science.

Originating in the Mediterranean, B. oleracea is grown all over the world and is highly valued for its nutritional value and variety in cooking. Its susceptibility to pests, diseases, and environmental stressors, however, poses significant challenges to sustaining consistent crop quality and productivity. The BASIC PENTACYSTEINE gene significantly impacts plant growth and responses to abiotic stresses. Nevertheless, little is known about its precise role and the underlying biological processes in B. oleracea. Eleven BPC genes in B. oleracea were identified by a thorough genome-wide investigation and categorized into three categories according to their structural traits and gene motifs. There were eight different chromosomes on which these BoBPCs were located. Comparative synteny analysis was used to reveal the evolutionary traits of potatoes, Arabidopsis, and B. oleracea. The BoBPC family genes in B. oleracea were found to have specific cis-elements linked to growth, stress responses, and hormone regulation when their promoter regions were studied. Cuticular wax synthesis expression revealed that all BoBZR1 genes, from wild to mutant, expressed at varied amounts in distinct types. Moreover, distinctive BoBPC gene expression patterns were found in the seven distinct tissues that were studied. Our thorough analysis shows that the BoBPC family is widely involved in B. oleracea developmental processes. The present findings provide an established theoretical basis for further exploration into the composition and roles of BoBPC in B. oleracea.

Background: Tumor mutational burden (TMB) is increasingly recognized as a vital biomarker for predicting the efficacy of immune checkpoint inhibitors (ICIs) in cancer treatment. Despite its growing importance, the effectiveness of TMB as a predictive marker are well established in lung cancer and melanoma but remain ambiguous for breast and prostate cancers. Objective: This study aims to evaluate the role of TMB in predicting response to ICIs across four major cancer types—lung, melanoma, breast, and prostate—and to address the variability in TMB's predictive value in different cancers. Methods: A comprehensive review of the current literature was performed, analysing studies that investigated TMB and its association with ICI therapy outcomes in the specified cancer types. Results: The analysis reveals a strong consensus on the predictive value of TMB in lung cancer and melanoma, where high TMB levels are associated with improved clinical outcomes and better responses to ICIs. In contrast, the evidence for breast and prostate cancers is less conclusive, with variability in results highlighting the need for further research. Specifically, high TMB in these cancers does not consistently predict better responses to ICIs, suggesting that additional biomarkers or refined criteria might be necessary. Conclusion: TMB is a promising biomarker for predicting responses to ICI therapy, particularly in lung cancer and melanoma. However, its predictive value in breast and prostate cancers remains uncertain, underscoring the need for more extensive studies. Future research should focus on standardizing TMB evaluation methods and exploring additional biomarkers to improve treatment personalization and outcomes in these cancer types.

This study aims to examine the non-volatile Particle Number (PN) emissions of a retrofitted Heavy-Duty Spark-Ignition (HD-SI) engine powered by liquefied petroleum gas (LPG) under both steady-state and transient conditions. The engine was tested under seven steady-state operating points to investigate the PN behavior and Particle Size Distribution (PSD) upstream and down-stream of the Three-Way Catalyst (TWC). This analysis intends to assess the impact of including particles with diameters ranging from 10 nm to 23 nm in the total particle count, a consideration for future regulations. The study employed the World Harmonized Transient Cycle (WHTC) for transient conditions to encompass the same engine working region used in the steady-state analysis. A Dekati FPS-4000 diluted the exhaust sample to measure the PSD and PN for particle diameters between 5.6 nm and 560 nm using the TSI-Engine Exhaust Particle Sizer (EEPS) 3090. Findings indicate that PN levels tend to increase downstream of the TWC under steady-state conditions in operating points with low exhaust gas temperatures and flows (equal to or less than 500 °C and 120 kg/h). Furthermore, the inclusion of particles with diameters between 10 nm and 23 nm leads to an increase in PN emissions by 17.70% to 40.84% under steady conditions and by an average of 40.06% under transient conditions, compared to measurements that only consider particles larger than 23 nm. Notably, in transient conditions, most PN emissions occur during the final 600 seconds of the cycle, linked to the most intense phase of the WHTC.

Abstract: This article provides a brief review of the ontogeny of chondrocytes and the pathophysiology of osteoarthritis (OA), and details how physical exercise improves the health of osteoarthritic joints and enhances the potential of mesenchymal stem cells for successful transplantation therapy. In response to exercise chondrocytes increase their production of glycosaminoglycans, bone morphogenic proteins and antiinflammatory cytokines and decrease their production of proinflammatory cytokines and matrix degrading metalloproteinases. These changes are associated with improvements in cartilage organization and reductions in cartilage degeneration. Studies in humans indicate that exercise increases peripheral blood recruitment of bone marrow-derived mesenchymal stem cells (BM-MSC) and upregulates BM-MSC expression of osteogenic and chondrogenic genes, osteogenic micro-RNAs, and osteogenic growth factors. Rodent experiments are uniform in demonstrating that exercise enhances the osteogenic potential of BM-MSC while diminishing their adipogenic potential, and that exercise done after stem cell implantation may benefit stem cell transplant viability. Physical exercise also exerts a beneficial effect on the skeletal system by decreasing immune cell production of osteoclastogenic cytokines interleukin (IL)-1β, tumor necrosis factor (TNF)-α, and interferon (INF)-γ while increasing their production anti-osteoclastogenic cytokines IL-10 and transforming growth factor (TGF)-β. In conclusion, physical exercise done both by stem cell donors and recipients may improve the outcome of mesenchymal stem cell transplantation.

Elevated carbon dioxide (eCO₂) stimulates wheat grain yield, but simultaneously reduces protein (N) concentration. Also other essential nutrients are subject to change. This study is a comprehensive synthesis of wheat experiments with eCO₂, estimating effects on N, minerals (B, Ca, Cd, Fe, K, Mg, Mn, Na, P, S, Zn), and starch. Analysis was made by i) deriving response functions for the relative effect on element concentration in relation to CO₂ concentration, ii) meta-analysis to test the magnitude and significance of observed effects, and iii) relating CO₂ effects on minerals to effects on N and grain yield. Responses range from zero to strong negative effects of eCO₂ on mineral concentration, with largest reductions for the nutritionally important elements N, Fe, S, Zn and Mg. Together with the positive but small and non-significant effect on starch concentration, the large variation in effects suggests that CO₂-induced responses cannot be explained by a simple dilution model. To explain the observed pattern, uptake and transport mechanisms may have to be considered, along with the link of different elements to N uptake. Our study shows that eCO₂ has a significant effect on wheat grain stoichiometry, with implications for human nutrition in a world of rising CO₂.

Dynamic time history analysis is a powerful and effective method to study the seismic response of tunnels, the dynamic time history to analyze the seismic response of the tunnel in the typical subway in this paper. The analysis results show that the overall levelling of the tunnel will not affect the tunnel too much, and the seismic response of the tunnel is mainly related to the relative displacement of the ground around the tunnel. The analysis results show that the internal force of the tunnel and the tunnel inclination have a good linear relationship, and the tunnel inclination can be used to measure the magnitude of the seismic response of the tunnel.

Floods are a common natural disaster whose severity in terms of duration, water resource volume, peak and accumulated rainfall-based damage are likely to differ significantly for different geographical regions. In this paper, we first propose a novel hourly flood index (SWRI24−hr−S), derived from normalising the existing 24-hourly water resources index (WRI24−hr−S) in literature, to monitor flash flood risks on an hourly scale. The proposed SWRI24−hr−S is adopted to identify a flood situation and derive its characteristics, such as the duration (D), volume (V) and peak (Q). The comprehensive result analysis establishes the practical utility of SWRI24−hr−S in identifying flood situations at seven study sites in Fiji between 2014 and 2018 and deriving their characteristics (i.e., D, V, and Q). Secondly, this study develops a vine copula-probabilistic risk analysis system that models the joint distribution of flood characteristics (i.e., D, V, and Q) to extract their joint exceedance probability for the seven study sites in Fiji, enabling probabilistic flood risk assessment. The vine copula approach, particularly suited to Fiji’s study sites, introduces a novel probabilistic framework for flood risk assessment. The results show moderate differences in the spatial patterns of joint exceedance probability of flood characteristics in different combination scenarios generated by the proposed vine copula approach. In the worst-case scenario, the probability of any flood event occurring where the flood volume, peak and duration are likely to exceed the 95th-quantile value (representing an extreme flood event) is found to be less than 5% for all study sites. The proposed hourly flood index and the vine copula approach can be feasible and cost-effective tools for flood risk monitoring and assessment. The methodologies proposed in this study can be applied to other data-scarce regions where only rainfall data is available, offering crucial information for flood risk monitoring, assessment, and the development of effective mitigation strategies.

Sensory descriptive analysis was used to evaluate the aged Feng-flavored baijiu. The results indicated that there are notable differences in the samples of different ages. The samples with shorter storage times and fresh distilled Baijiu present bran flavor, and fresh green flavor. with the increase of storage time, the fragrance of honey, sweetness, flowers, and aging gradually increases. The samples of Feng-flavored baijiu were dected by Headspace solid-phase microextraction (HS-SPME) combined with comprehensive two-dimensional gas chromatography time-of-flight mass spectrometry (GC×GC–TOFMS) , in total, 496 sustances were identified in all samples, mainly containing 14 types of substances, such as esters, aldehydes etc., of which 42 substances were found in Feng-flavored baijiu for the first time. Chemometrics was used to analyze the key differential compounds. 143 differential compounds closely related to aging were preliminarily screened, and principal component analysis revealed that these samples were separated by year. 65 differential compounds were selected out by partial least squares discriminant analysis(PLS-DA). Furthermore, 43 key differential compounds were selected from the aged Feng-flavored baijiu combined with variable importance in projection and Pearson correlation coefficients. Partial least squares regression (PLSR) was used to research the correlation of sensory properties and key differential compounds, and the results indicated that most compounds were closely related to the aged Baijiu . This study afford theoretical basis and reference for flavor research of Feng-flavored baijiu.

With the advances in industry and commerce, passengers have become more accepting of environmental sustainability issues; thus, more people now choose to travel by bus. Government administration constitutes an important part of bus transportation services as the government gives the right-of-way to transportation companies allowing them to provide services. When these services are of poor quality, passengers may lodge complaints. The increase in consumer awareness and developments in wireless communication technologies have made it possible for passengers to easily and immediately submit complaints about transportation companies to government institutions, which has brought drastic changes to the supply-demand chain comprised of the public sector, transportation companies, and passengers. This study proposed the use of big data analysis technology including systematized case assignment and data visualization to improve management processes in the public sector and optimize customer complaint services. Taichung City, Taiwan was selected as the research area. There, the customer complaint management process in public sector was improved, effectively solving such issues as station-skipping, allowing the public sector to fully grasp the service level of transportation companies, improving the sustainability of bus operations, and supporting the sustainable development of the public sector-transportation company-passenger supply chain.

Background: Colorectal cancer (CRC) patients experienced multiple chemotoxicity affecting treatment compliance, survival, and quality of life (QOL). Prior research shows clinician-reported chemotoxicity (i.e., grading scales or diagnostic codes) predicts rehospitalization and cancer survival. However, a comprehensive synthesis of clinician-reported chemotoxicity is still lacking. Objectives: We conducted a systematic review and meta-analysis to determine the chemotoxicity's prevalence and risk factors in CRC. Methods: A systematic search from 2009 to 2024 yielded 30 studies for review, with 25 included in the meta-analysis. Results: Pooled prevalences of overall, non-hematological, and hematological moderate-to-severe toxicities were 45.7%, 39.2%, and 25.3%, respectively. The most common clinician-reported chemotoxicities were gastrointestinal (GI) toxicity (22.9%) and neuropathy or neutropenia (17.9%). Significant risk factors at baseline were malnutritional status, frailty, impaired immune or hepato-renal functions, short telomere lengths, low gut lactobacillus levels, age, female sex, aggressive chemotherapy, and low QOL. Age was associated with neutropenia (β: -1.44) and GI toxicity (β:1.85) (Ps 65 y.o.) had higher prevalences of overall (OR: 1.14) and GI (OR: 1.65) toxicities, but a lower prevalence of neutropenia (OR: 0.65) than younger adults (Ps

Background : The quantification of electromyographic activity using surface electrodes is inval-uable for understanding gait disorders in patients with central nervous system lesions. We propose to evaluate a commercially available low-cost system compared to a reference system in partic-ipants with stroke-related movement disorders in functional situations. Methods : Three hemiparetic participants performed three functional tasks: two treadmill walks at different speeds and a sit-to-stand test. The vastus lateralis and gastrocnemius medialis muscles were equipped with two EMG sensors. The comparison between the two EMG systems was based on 883 identified cycles. Spearman’s correlation coefficients (SC), linear correlation coefficients (LCC), and cross-correlation coefficients (CCC) were calculated. Results : The main results indicate good to very good similarity of the EMG signals collected from the two tested sEMG systems. In the comfortable walking condition, an SC of 0.894±0.091 and an LCC of 0.909±0.094 were noted. In the fast walking condition, an SC of 0.918±0.064 and an LCC of 0.935±0.056 were observed. For the 1-minute sit-to-stand test an SC of 0.880±0.058 and an LCC of 0.881±0.065 were noted. Conclusions : This study demonstrates good to very good similarity between the two sEMG systems, enabling the analysis of muscle activity during functional tasks.

This study investigates the influence of adding hydrogen as an additive to gasoline in a four-stroke engine, utilizing a comprehensive thermodynamic comparative analysis conducted with self-developed engine model. The research aims to assess the performance, emissions, and efficiency of the engine when using gasoline-hydrogen blends, and to provide insights into the potential benefits of this approach. First the engine performance and emissions under different hydrogen blending levels were examined. A range of different air-to-fuel ratios (rich to lean) and varying percentages of hydrogen were considered. This systematic variation allowed for a detailed evaluation of the influence of hydrogen content on combustion efficiency, power out-put, and emissions characteristics. The analysis results included key parameters such as indicated specific fuel consumption and mean effective pressure. Additionally, the study focused on range prediction of nitrogen oxides (NOx) emissions, which are a critical environmental concern asso-ciated with internal combustion engines. The analysis of pressure and temperature profiles throughout the engine cycle shed light on the combustion characteristics and efficiency im-provements associated with hydrogen addition. In terms of emissions, the study projected that all emissions were reduced except NOx, which is highly dependent on hydrogen percentage, and it might be reduced in some cases, but with higher temperatures and pressures associated with hydrogen addition in most cases there is actually NOx increase, especially at higher engine loads.

The iron roughneck is an automated equipment utilized for the connection and removal of drilling tools. This paper presents the design of an integrated iron roughneck, providing a detailed introduction to its clamp body structure, along with an analysis of its structural characteristics and performance requirements. The study delves into the integration mode and working characteristics of the clamping mechanism and spin buckle mechanism for the integrated upper clamp body structure of the iron roughneck. Additionally, this paper conducts an in-depth theoretical study on the spin buckle mechanism. Firstly, it analyzes the actual working condition of the spin buckle roller from two perspectives: contact theory and rolling friction theory, determining the structural form of the spin buckle roller. Secondly, it investigates the relative displacement between the spin buckle mechanism and the drilling tool, proposing a design method for the floating device mounted on the spin buckle roller and establishing the kinematic equation of the spin buckle roller under the influence of the floating device. Furthermore, the kinematic equations of the spin buckle roller under the influence of the floating device are established. Finally, a dynamics simulation experiment is performed to simulate the working process of the spin buckle mechanism under actual working conditions, analyzing the dynamics and kinematics of the spin buckle mechanism and obtaining the relevant parameter curves of the spin buckle mechanism and drilling tools. Through data comparison and analysis, the correctness of the theoretical analysis results and the rationality of the performance and structure of the spin buckle mechanism are verified.

We present a very computationally light and fast approximation algorithm and then verify it with genetic algorithm and simulated annealing. We show that our algorithm is on par with GA and SA in terms of output produced while having a tightly bounded time complexity. Our algorithm works best when there is a strong positive correlation between the reliability of a component and its cost. We present two algorithms with the same essence. One of them is system cost bounded and the other is target reliability bounded. Our proposed algorithm works on a subsystem level redundancy instead of component level redundancy.

The leaves of Nicotiana glauca (Solanaceae) plant, are known for its major cause of health concern. This study investigated the antioxidant activity and polyphenols composition of aerial parts of N.glauca collected from its wild habitat in Jordan, using Methanol-Conventional (MC) and deep eutectic solvents (DESs) extraction methods in addition to nicotine content determination using UHPLC. The results have shown that the MC extract contains fewer total phenols and flavonoid content than the DES extract at ratio of 90% (0.1194 ±0.009 and 0.311± 0.020 mg/mL equivalent to gallic acid) and (0.01084±0.005 and 0.928 ± 0.09 mg/mL equivalent to rutin), respectively. Moreover, the study showed that the MC extract contains 635.07 ppm nicotine compared to the DES extraction method, which contains 1194.91 ppm. Both the MC and the DES extracts exhibited weak antioxidant activities with the highest was 33%inhibition equivalent to ascorbic acid was found for DES at (90%) ratio. The UHPLC-MS/MS analysis revealed the presence of variations in the detected compounds between the two extraction methods used. This study found that en-vironmentally friendly DES extraction of N. glauca produced higher phenol and flavonoid content than MC method, highlighting green chemistry methods' superior efficiency and environmental benefits for extracting valuable phytoconstituents.

This paper proposes a novel phase-resolved partial discharge (PRPD) sensor embedded in MV-class bushing for high-accuracy insulation analysis. The design, fabrication, and evaluation of a PRPD sensor embedded in MV-class bushing aimed to detect partial discharge (PD) pulses that are phase-synchronized with the applied primary HV signals. A prototype PRPD sensor was composed of a flexible printed circuit board (PCB) with dual-sensing electrodes, utilizing a capacitive voltage divider (CVD) principle for voltage measurement and D-dot principle for PD detection, and a signal transducer with passive elements. A PD simulator was prepared to emulate typical PD defects, i.e., a metal protrusion. The voltage measurement precision of the prototype PRPD sensor was satisfied with the accuracy class of 0.2 specified in IEC 61869-11, as the maximum corrected voltage error ratios and corrected phase errors in 80%, 100%, and 120% of the rated voltage (13.2 kV) were less than 0.2% and 10 minutes, respectively. In addition, the prototype PRPD sensor had good linearity and high sensitivity for PD detection compared with a conventional electrical detection method. According to performance evaluation tests, the prototype PRPD sensor embedded in the MV-class bushing can measure PRPD patterns phase-synchronized with the primary voltage without any additional synchronization equipment or system. Therefore, the prototype PRPD sensor holds potential as a substitute for conventional commercial PD sensors. Consequently, this advancement could lead to the enhancement of power system monitoring and maintenance, contributing to the digitalization and minimization of power apparatus.

Although instructional feedback plays an essential role in regulating learning and improving performance, few studies have systematically investigated the needs of teachers and students for instructional feedback system or developed designs and experiments, especially at the high school level. To address this research need, the present study investigated the needs of selected students and teachers in a high school in Hubei Province, China, and designed and developed a diagnostic visual feedback system for an experimental study with 125 students from a 10th-grade biology class in the same high school. The results showed that this diagnostic visual feedback report improved student performance (ES=0.37) and that functions such as misconception location, knowledge diagnosis, and knowledge alert were well received by students. These findings have multiple implications for facilitating the design and development of diagnostic visual feedback system.

For effective warehouse management, various criteria should be taken into consideration in terms of inventory management, demand, transportation distance, usage area, delivery-waiting times, and minimizing the costs that may arise from them. Because, the purpose of the product assignment problem is to minimize the total transport distance during storage and to reduce the space required for product assignment. However, the storage location assignment problem (SLAP) occurs simultaneously with production planning activities in real life. In this study, an integrated mixed-integer nonlinear (MINLP) mathematical model is proposed, which includes the assignment of products to storage areas and production planning, using the TOPSIS (Technique for Order Preference by Similarity to Ideal Solution) class based policy for storage systems where multiple criteria are important. In the TOPSIS class-based policy, weight and waiting time criteria are taken into account, as well as the COI (Cube-per-order index index), which is widely used in the literature. In addition, a decision support system flow has been proposed that takes into account the single criterion, multiple criteria and COI index criteria of the developed model and provides its integration with different product assignment policies. Detailed literature research; It has been revealed that the proposed mathematical model and decision support system flow have the feature of applying an existing field of science to a new problem.

Causative agent of the viral pneumonia outbreak in the World identified as SARS-CoV2 leads to a severe respiratory illness like SARS and MERS. The pathogen spreading has turned into a pandemic dissemination and increased the mortality rate. Therefore, useful information is urgently necessary for effective control of the disease. Our study shows the existence of unvarying sequence with no mutation, including ORF1ab regions in 134 high-quality filtered genome sequences of SARS-CoV2 downloaded from the GISAID database. We have detected this sequence stability by using MAUVE analysis and pairwise alignment with Global Needleman Wunsch algorithm for each two different sequences, reciprocally. They also confirmed all these results were also with the Clustal W analysis. The first 6500 bp including ORF1ab region is an unvarying sequence. According to the highest TM-score of predicted protein structure analysis, the results showed it is very similar to spike protein of feline infectious peritonitis virus strain UU4 (PDB 6JX7) depending on amino acid sequences encoded by this unvarying region, and N-acetyl-D-glucosamine is the ligand of this protein. These results have confirmed that N-acetyl-D-glucosamine could play an important role in controlling of SARS-CoV-2. Also, our molecular docking analysis data supports a strong protein-ligand interaction of N-acetyl-D-glucosamine with spike receptor-binding domain bound with ACE2 (PDB 6M0J) and RNA-binding domain of nucleocapsid phosphoprotein (PDB 6WKP) from SARS CoV-2. Therefore, binding of N-acetyl-D-glucosamine to these proteins could inhibit SARS CoV-2’s replication. In the present work, we have suggested providing a repurposing compound for further in vitro and in vivo studies and new insights for ongoing clinical treatments as a new strategy to control of SARS-CoV-2 infections.

Citrus species essential oils (EOs) are significant sources of bioactive compounds and demonstrate diverse therapeutic effects. However, limited documentation exists regarding the phytochemicals associated with their biological activities. This study aims to assess the antioxidant activity, plant inhibitory properties, and brine shrimp cytotoxic effects of EOs derived from three Citrus species: C. sinensis, C. limon, and C. hystrix. Utilizing chemometric analysis and gas chromatography-mass spectrometry (GC-MS) fingerprints, the volatile components contributing to antioxidant activity were elucidated. The peels of the Citrus samples were hydro-distillated to obtain EOs, and subsequently subjected to antioxidant, plant inhibitory, and brine shrimp cytotoxic assays. The results indicated that C. limon EO exhibited the highest antioxidant activity, while C. hystrix and C. sinensis EOs demonstrated pronounced inhibitory effects against Aetrmia salina and Lactuca sativa, respectively. GC-MS analysis facilitated the identification of key compounds in each EO. Principal component analysis (PCA) and hierarchy cluster analysis (HCA) effectively categorized Citrus EOs based on their antioxidant properties, highlighting the proximity of C. limon and C. sinensis. Among the identified compounds, D-limonene, α-Terpineol, Caryophyllene, (+)-3-Carene, β-Pinene, (-)-Spathulenol, trans-p-Mentha-1(7),8-dien-2-ol, and trans-Verbenol were the most discriminating compounds affected the antioxidant activity of C.limon and C. sinensis EOs.

Volatile organic compounds (VOCs) released from plants have been correlated with disease-status. Analysis of VOCs using GC-MS is time-consuming, laboratory-based, and requires specialist training. Electronic nose devices (E-nose) provide a portable alternative. Three different E-nose devices were compared to assess how accurately they could detect Mango Twig Tip Dieback and Panama disease in banana. The devices were initially trained on known volatiles, then pure cultures of Pantoea sp., Staphylococcus sp., and Fusarium odoratissimum, and finally, on infected and healthy mango leaves and field-collected, infected banana pseudo-stems. The experiments were repeated three times with six replicates for each host-pathogen pair. The variation between healthy and infected host materials was evaluated by principal component and linear discriminant analysis, cross-validation and chemometric data analysis. GC-MS analysis was conducted contemporaneously and identified an 80% similarity between healthy and infected plant material. The portable C 320 was 100% successful in discriminating known volatiles but had a low capability in differentiating healthy and infected plant substrates. The advanced devices (PEN 3 / MSEM 160) successfully detected healthy and diseased samples with a high variance. The results suggest that E-nose devices are more sensitive and accurate in detecting changes of VOCs between healthy and infected plants compared to headspace GC-MS.

The apicomplexan parasite, Sarcocystis neurona causes the degenerative neurological equine protozoal myeloencephalitis (EPM) disease of horses. Due to its host range expansion, S. neurona is an emerging threat that requires close monitoring. In apicomplexans, protein kinases (PKs) have been implicated in a myriad of critical functions such as host cell invasion, cell cycle progression and host immune responses evasion. Here, we used various bioinformatics methods to define the kinome of S. neurona and phylogenetic relatedness of its PKs to other apicomplexans. Further, three-dimensional (3D) homology models for selected S. neurona putative PKs were constructed and evaluated for inhibitor docking. We identified 92 putative PKs clustering within the AGC, CAMK, CK1, CMGC, STE, TKL, aPK and OPK groups. Although containing the universally conserved PKA (AGC group), S. neurona kinome was devoid of PKB and PKC, but contained the six apicomplexan conserved CDPKs (CAMK group). The OPK group was represented by ROPKs 19A, 27, 30, 33, 35 and 37, but was devoid of the virulence-associated ROPKs 5, 6, 18 and 38. Two out of the three S. neurona CK1 enzymes had high sequence similarities to T. gondii TgCK1-α and TgCK1-β and the Plasmodium PfCK1. Docking of four inhibitors onto homology models of putative ROP27 and PKA indicated that inhibition of S. neurona PKs is feasible, but needs to be experimentally tested. The essentiality of apicomplexan PKs makes the elucidation of S. neurona kinome a key milestone for development of novel therapeutics for EPM.

Grand challenges represent wicked problems that affect many people globally. To overcome grand challenges and sustain our existence as human beings, issues have become increasingly central, and in recent years have led to an increase in research and literature on grand challenges affecting both international business areas and multinational enterprises. The aim of this study is to assess the status of literature in all areas connected to multinational corporations and grand challenges, which are global issues with significant implications. From 2013 to 2023, the WoS database was used to investigate eight search terms from literature, and bibliometric and thematic analyses were carried out based on the principles of systematic literature analysis. The most focused areas of the research are performance, multinational enterprises, foreign direct investment, management, firms’ innovation, knowledge, international business, and impact. Asian, African, European, and other countries may emerge together in different clusters depending on whether the major challenges they are struggling with are similar or identical. the terms of grand challenges and innovation (open and social), technology transfer, R&amp;D internalization, digital transformation or technology and artificial intelligence in the literature of multinational enterprises indicates that these themes are used as a tool to solve grand challenges.

Sentiment analysis plays a crucial role in understanding customer feedback, guiding product development, and informing business decisions. This paper introduces term sentiment entropy (TSE), a novel weighting method that leverages the distribution of sentiment labels associated with words to enhance text classification accuracy. TSE complements traditional TF-IDF techniques by capturing the nuances of sentiment variation across different contexts. Experiments across diverse public datasets demonstrate TSE's potential to improve sentiment analysis performance, especially in capturing subtle sentiment shifts and adapting to specific domains. While computational cost and label quality pose challenges, TSE offers a promising avenue for refining sentiment analysis and opening new research frontiers.

Diacylglycerol kinase (DGK) is a lipid kinase that phosphorylates diacylglycerol (DAG) to generate phosphatidic acid (PA). Based on converting one important signaling molecule (DAG) to another (PA), DGK plays an important role in plant responses to abiotic stress including waterlogging stress. However, no studies have been reported on the characterization of the DGK gene family in the waterlogging-tolerant kiwifruit germplasm, Actinidia valvata Dunn. Here, we identified 18 AvDGK genes in the A. valvata genome. The phylogenetic analysis showed that AvDGKs can be classified into three clusters, and members within the same cluster have similar domain distribution, exon-intron structures and conserved motif compositions. Chromosome localization analysis revealed that all the AvDGK genes are located across 18 different chromosomes. There were 29 duplicated gene pairs in kiwifruit and all had undergone purifying selection during evolution. Promoter cis-element analysis revealed that the cis-elements within AvDGK genes are associated with multiple functions, including phytohormone signal transduction, stress response, and plant growth and development. The expression pattern analyses indicated that AvDGK play an important role in the fruit development and plant response to waterlogging stress. AvDGKs gene family in the tetraploid A. valvata genome might promote PA synthesis and subsequent signal transduction both under short-term and long-term waterlogging stress. These results provide information regarding the structural characteristics and potential function of DGK genes within kiwifruit and lay a fundamental basis for further research into breeding for enhancing the kiwifruit’s tolerance to waterlogging stress.

Significant Wave Height(SWH) is a crucial parameter in oceanographic research, essential for understanding various marine and atmospheric processes. Traditional methods for obtaining SWH, such as ship-based and buoy measurements, face limitations like limited spatial coverage and high operational costs. With the advancement of Global Navigation Satellite Systems reflectometry(GNSS-R) technology, a new method for retrieving SWH has emerged, demonstrating promising results. This study utilizes Radio occultation sounder(GNOS) data from the FY-3E satellite and incorporates the latest Vision Transformer(ViT) technology to investigate GNSS-R-based SWH retrieval. We designed and evaluated various deep learning models, including ANN-Wave, CNN-Wave, Hybrid-Wave, Trans-Wave, and ViT-Wave. Through comparative training using ERA5 data, the ViT-Wave model was identified as the optimal retrieval model. The ViT-Wave model achieved an Root Mean Square Error(RMSE) accuracy of 0.4052 meters and Mean Absolute Error(MAE) accuracy of 0.2700 meters, significantly outperforming both traditional methods and newer deep learning approaches utilizing Cyclone Global Navigation Satellite Systems(CYGNSS) data. These results underscore the potential of integrating GNSS-R technology with advanced deep learning models to enhance SWH retrieval accuracy and reliability in oceanographic research.

Environment pollution is the major problem for all the sectors. In environment pollution there are different types of pollution is included such as air pollution, water pollution, soil pollution etc. In these types of pollution most of it is air pollution. There are many reasons for pollution of air. Human advance in science but one of the major draw backs of science is the pollution of air rapidly. Air pollution is injurious to health. Every year a large number of people died for the effects of air pollution. It can be improved in many ways among these ways technology upgradation plays a major role here. There are various method that prevent air pollution. Many researchers tried and is trying to prevent the air pollution in many ways. In this review paper I summarise the existing research on different ways for preventing air pollution in addition I will discuss the gaps and future aspect on this topic.

OSI model used to be common network model for years. In the case of ad hoc networks with dynamic topology and difficult radio communications conditions, gradual departure is happening from the classical kind of OSI network model with a clear delineation of layers (physical, channel, network, transport, application) to the cross-layer approach. The layers of the network model in ad hoc networks strongly influence each other. Thus, the cross-layer approach can improve the performance of an ad hoc network by jointly developing protocols using interaction and collaborative optimisation of multiple layers. The existing cross-layer methods classification is too complicated, because it’s based on the whole manifold of network model layers combinations, regardless their importance. In this work, we review ad hoc networks cross-layer methods, propose the new useful classification of cross-layer methods, and show future research directions in ad hoc networks cross-layer methods development. The proposed classification can help to simplify the goal-oriented cross-layer protocol development.

With the rapid development of artificial intelligence, machine learning is gradually becoming popular in predictions in all walks of life. In meteorology, It is gradually competing with traditional climate predictions dominated by physical models. This survey aims to consolidate the current understanding of Machine Learning (ML) applications in weather and climate prediction—a field of growing importance across multiple sectors including agriculture and disaster management. Building upon an exhaustive review of more than 20 methods highlighted in existing literature, this survey pinpointed eight techniques that show particular promise for improving the accuracy of both short-term weather and medium-to-long-term climate forecasts. According to the survey, while ML demonstrates significant capabilities in short-term weather prediction, its application in medium-to-long-term climate forecasting remains limited, constrained by factors such as intricate climate variables and data limitations. Current literature tends to focus narrowly on either short-term weather or medium-to-long-term climate forecasting, often neglecting the relationship between the two, as well as general neglect of modelling structure and recent advances. By providing an integrated analysis of models spanning different time scales, this survey aims to bridge these gaps, thereby serving as a meaningful guide for future interdisciplinary research in this rapidly evolving field.

Sign language recognition is essential in hearing-impaired people’s communication. Sign language recognition is an important concern in computer vision and has been developed with rapid progress in image recognition technology. However, sign language recognition using a general monocular camera has problems with occlusion and recognition accuracy in sign language recognition. In this research, we aim to improve accuracy by using a 2-axis bending sensor as an aid in addition to image recognition. We aim to achieve higher recognition accuracy by acquiring hand keypoint information of sign language actions captured by a monocular RGB camera and adding sensor assist. To improve sign language recognition, we need to propose new AI models. In addition, the amount of dataset is small because it uses the original data set of our laboratory. To learn using sensor data and image data, we used MediaPipe, CNN, and BiLSTM to perform sign language recognition. MediaPipe is a method for estimating the skeleton of the hand and face provided by Google. In addition, CNN is a method that can learn spatial information, and BiLSTM can learn time series data. Combining the CNN and BiLSTM methods yields higher recognition accuracy. We will use these techniques to learn hand skeletal information and sensor data. Additionally, the 2-axis Bending sensor glove data support training AI model. Using these methods, we aim to improve the recognition accuracy of sign language recognition by combining sensor data and hand skeleton data. Our method performed better than using skeletal information, achieving 96.5% accuracy in Top-1.

Graphene is a two-dimensional carbon atom with a hexagonal honeycomb-like structure in which the sp2 hybridization occurs. GO sheets are highly oxidized and have oxygen-containing groups. Properties of electronics, mechanicals, magnetics, and optics, Oxidized Methods for Brodies, Staudenmaier, Hofmann, Hummers, Improved Hummers, and Tour's Methods Reduction of Graphene oxide methods Chemical Reduction using sodium borohydride, 2,4-dinitrophenylhydrazine, Hydrazine hydrate, Thermal Reduction, Hydrothermal Reduction, Exfoliation Reduction, Catalytic Reduction, and the green synthesis route for reduction, The reduction of graphene oxide has a wide range of applications, including its use in energy storage devices for Solar cells, Supercapacitors, LIG-based sensors, River Water sensors, Battery, hydrovoltaic generators, OLED Screen, and Graphene Shielding. This review will determine the future of a few applications.

This article focuses on methods for designing heuristic models within the paradigm of systems theory and in the disciplinary context of intercultural communication. The main question arises from the striking observation that the common language is insufficient to develop knowledge about human communication, especially when many factors of complexity (such as ambiguity, paradoxes, or uncertainty) are involved in the composition of an abstract research object. This epistemological, theoretical, and methodological problematic is one of the main challenges to the scientificity of anthropological theories and concepts on culture. Moreover, these questions lie at the heart of research in intercultural communication. Authors and theorists in the complexity sciences have already stressed the need, in such case, to think in terms of models or semiotic representations, since these tools of thought can mediate much more effectively than unformalized language between the heterogeneous set of perceptions arising from the field of experience, on the one hand, and the philosophical principles that organize speculative thought, on the other. This sets the scene for a reflection on the need to master the theory of heuristic models when it comes to developing scientific knowledge in the field of intercultural communication. In this essay, my first aim is to make explicit the conditions likely to ensure the heuristic value of a model, while my second aim is to clarify the operational function and required level of abstraction of certain terms such as concepts, categories, headings, models, systems, or theories that are among the most commonly used by academics in their descriptive accounts or explanatory hypotheses. To achieve this second objective, I propose to create cognitive meta-categories to identify the three (nominal, cardinal or ordinal) roles of words in the reference grids we use to classify our ideas, and to specify how to use these meta-categories in the construction of our heuristic models. Alongside the theoretical presentation, examples of application are provided, almost all of which are drawn from my own research into the increased cultural vigilance of the majority population in Quebec since the reasonable accommodation crisis in this French-speaking province of Canada. The typology I propose will perhaps help to avoid the confusions regularly committed by authors who attribute only cosmetic functions to words that nevertheless have a highly heuristic value, and who forget to consider the logical leaps of their theoretical thinking in the construction of heuristic models.

Structured extraction of emergency event information can effectively enhance the ability to re-spond to emergency events. This article focuses on the extraction of Chinese document-level emergency events, which mainly faces two key issues in this field: first, related datasets; Secondly, existing DEE (document-level event extraction) studies mostly use sequence annotation to extract candidate entities in the subtask of candidate entity extraction without considering the problem of role overlapping between candidate entities. On the one hand, this article constructs a Chinese document-level emergency extraction dataset, CDEEE, which first annotates the issues of argu-ment scattering, multiple events, and role overlapping. On the other hand, this article proposes a model RODEE for the problem of role overlapping in DEE tasks. This model first uses two in-dependent modules to represent the head and tail positions of candidate entities, then uses a multiplication attention mechanism to interact with the two to obtain a scoring matrix. Finally, role-overlapping candidate entities are predicted to assist in completing DEE tasks. Experiments were conducted on our manually annotated dataset, CDEEE, and the results showed that RODEE can effectively solve the problem of role overlapping in candidate entities and improve the performance of the DEE model.

The adoption of harmful postures due to a sedentary lifestyle, which involves long periods at work in offices, is a factor that exacerbates musculoskeletal risks. To examine these risks, there are numerous postures analysis methods, such as Rapid Upper Limb Assessment (RULA) and Rapid Office Strain Assessment (ROSA). RULA is a consolidated method to evaluate the exposure of individual workers to ergonomic risk factors associated with upper extremity musculoskeletal disorders. In turn, ROSA is a more recent method that quantifies exposure to risk factors in an office work environment. This research aims to identify whether there is harmony between these two methods, ROSA and RULA. Through applied research, from a qualitative perspective, the scientific procedures adopted were direct observation and ROSA and RULA postural assessment instruments. The study was conducted in the radiology service and focused on the outpatient reception workstation. Results indicated that further investigation must occur to make working conditions changes as soon as possible and that both methods are harmonic. As contributions of the analysis, we have discussed the working conditions and suggested improvements to reduce the risks of musculoskeletal morbidity symptoms. We recommend future studies aimed at measuring the levels of complementarity between these methods by quantitative approaches.

Drought is considered one of the severest natural disasters and it is difficult to predict it. This review article aimed to display the state of the art of methods used to predict and monitor types of droughts. We examine more than 30 indices and models to identify the strengths and weaknesses of methods and identify gaps remaining in this field. Examples of examined indies are Palmer Drought Severity Index (PDSI), Standardized Precipitation Index (SPI), and Standardized Precipitation Evapotranspiration Index (SPEI). The research found improvement in drought modeling, however, more focus and improvement are required to monitor and predict drought types. It also found that some methods outperform others such as PDSI, SPI, SPEI, EVI, NDVI, NDWI, VCI and TCI.

Through its suggestive name, non-targeted methods (NTMs) do not aim at a predefined "needle in the haystack". Instead, they exploit all the constituents of the haystack. This new form of analytical methods is increasingly finding applications in food and feed testing. However, the concepts, terms, and considerations related to this burgeoning field of analytical testing needs to be propagated for the benefit of ones associated in academic research, commercial development, and official control. This paper addresses the frequently asked questions around notations and terminologies surrounding NTMs. The widespread development and adoption of these methods also necessitates the need to develop approaches to NTM validation, i.e., evaluating the performance characteristics of a method to determine if it is fit-for-purpose. This work aims to provide a roadmap to approaching NTM validation. In doing so, the paper deliberates on the different considerations that influence the approach to validation and provides suggestions thereof.

With the increased availability of sequence data and even of fully sequenced and assembled genomes, phylogeny estimation of very large trees (even of hundreds of thousands of sequences) is now a goal for some biologists. Yet, the construction of these phylogenies is a complex pipeline presenting analytical and computational challenges, especially when the number of sequences is very large. In the last few years, new methods have been developed that aim to enable highly accurate phylogeny estimations on these large datasets, including divide-and-conquer techniques for multiple sequence alignment and/or tree estimation, methods that can estimate species trees from multi-locus datasets while addressing heterogeneity due to biological processes (e.g., incomplete lineage sorting and gene duplication and loss), and methods to add sequences into large gene trees or species trees. Here we present some of these recent advances and discuss opportunities for future improvements.

Classical methods for inverse problems are mainly based on regularization theory. In particular those which are based on optimization of a criterion with two parts: a data-model matching and a regularization term. Different choices for these two terms and great number of optimization algorithms have been proposed. When these two terms are distance or divergence measures, they can have a Bayesian Maximum A Posteriori (MAP) interpretation where these two terms correspond, respectively, to the likelihood and prior probability models.

MzSTools is a plugin for QGIS developed by the Institute of Environmental Geology and Geoengineering of the National Research Council (CNR-IGAG). The plugin has been designed as a set of practical and easy-to-use tools to carry out seismic microzonation (SM) studies, by producing standard compliant geographic database and maps, thus making them accurate, homogeneous and uniform for all municipalities in Italy. A geodatabase based on SQLite/SpatiaLite Relational Database Management System (RDBMS) has been designed to collect and store data related to elements such as: geognostic surveys; bedrocks and cover terrains; superficial and buried geomorphological elements; tectonic-structural elements; elements of geological instability such as landslide zones, liquefaction zones and zones affected by active and capable faults; homogeneous microzones in seismic perspective, microzones characterized by a seismic amplification factor. MzSTools assembles in a single software environment a set of useful tools in a configurable QGIS project template, comprising layers, symbol libraries, cartographic styles and print layouts for the SM maps. The plugin is open source and hosted on the GitHub platform, and available via the official QGIS plugins repository (https://plugins.qgis.org/plugins/MzSTools/).

In this study, a summary of the processes performed on the SPL for recycling, reduction in toxicity and treatment were examined on an industrial and laboratory scale. In writing this research, an attempt has been made to address the useful processes that have taken place in this field. Spent pot lining or SPL is a type of solid waste that is produced in the aluminum production process. After 3 to 8 years, the cathode blocks become problematic and can no longer be used, and need to be replaced due to adverse effects on cell function. SPL is known to be a hazardous waste to nature due to its fluoride and cyanide content. Research has shown that SPL ingredients have destructive and very dangerous effects on human DNA, which is why they are so important to maintain and recycle.

The conventional machine learning (ML) algorithms are continuously advancing and evolving at a fast-paced by introducing the novel learning algorithms. ML models are continually improving using hybridization and ensemble techniques to empower computation, functionality, robustness, and accuracy aspects of modeling. Currently, numerous hybrid and ensemble ML models have been introduced. However, they have not been surveyed in a comprehensive manner. This paper presents the state of the art of novel ML models and their performance and application domains through a novel taxonomy.

Salt stress is a major limiting factor for alfalfa yield due to its relatively low salt tolerance. High soil salinity adversely impacts alfalfa growth and development, leading to reduced yield. Melatonin (MT) is known to play a significant role in enhancing plant resistance to abiotic stresses. However, the mechanisms underlying melatonin-mediated abiotic stress responses, particularly salt stress, are not well understood. To address this gap, we conducted a study focusing on germinating alfalfa seeds under salt stress. Physiological indexes and transcriptomics analyses were carried out on the germinated seeds to investigate the effects of melatonin on alfalfa seedlings under salt stress conditions. Our results revealed that the application of melatonin led to an increase in shoot length and fresh weight of alfalfa seedlings under salt stress. Moreover, key physiological indexes such as peroxidase (POD) activity and glutathione (GSH) content were enhanced, while levels of malondialdehyde and superoxide anions decreased. Transcriptomic analysis identified a total of 2,131 differentially expressed genes in the salt-treated group, with 726 up-regulated and 1,405 down-regulated genes, while the MT-treated group showed 2896 differentially expressed genes, of which 1,097 were up-regulated and 1,799 were down-regulated. Further, KEGG enrichment analysis highlighted the enrichment of differentially expressed genes in pathways including flavonoid biosynthesis, ABC transporter, glutathione metabolism, and the MAPK signaling pathway, with these pathways more significantly enriched in the MT-treated group. These findings collectively suggest that melatonin plays a crucial role in alfalfa's response to salt stress and offer new insights into the genomic mechanisms underlying melatonin-mediated salt tolerance in alfalfa.

(1) Background: Depressional wetlands are highly vulnerable to changes in temperature and rainfall, affecting littoral vegetation, thus HydroGeoMorphic (HGM) wetland types. This study aimed to assess the utility of Sentinel-2A vegetation indices in enhancing delineation and sub-classify depressional HGM types. (2) Methods: We sampled 84 pairs of four vegetation indices from 10x10m plots along 14 belt transects in eight depressional wetlands in Mpumalanga, South Africa. We evaluated vegetation index differences between and within wetlands, focusing on lit-toral gradients. (3) Results: Significant differences (Bonferroni p

Spontaneous tumours in higher plants can develop depending on plant genotype without any pathogen invasion. Spontaneous tumour formation on the taproots is consistently observed in certain inbred lines of radish (Raphanus sativus var. radicula Pers.). In this work, we have sequenced the genomes of two closely related radish inbred lines that differ in their ability to spontaneously form tumours. We have identified numerous single nucleotide variants (amino acid substitutions, insertions or deletions) that are likely to be associated with the spontaneous tumour formation. Furthermore, we performed the identification of CLE and WOX genes the genomic sequences of the radish inbred lines and, as a result, identified two unique radish CLE genes which probably encode proteins with multiple CLE domains. The results obtained provide a basis for investigating the mechanisms of plant tumour formation and also for future genetic and genomic studies of radish.

Both soybean variety and processing affect product characteristics. This study’s objective was to characterize the effect of four extraction methods (variations of soaking and grinding) combined with cooking on the content and composition of phenolic substances, antioxidant and anti-DU145 prostate cancer cell proliferative properties of soymilk prepared from a yellow soybean of the ProSoy variety, which is a high protein variety. Results showed soymilk processing yield was the greatest by Method 4, but Method 2 gave the highest solids and protein yields by about 14 and 12%, respectively. Method 4, a two-step grinding also increased yields (8 and 7%, for solids and protein, respectively), and in all but one instance produced higher total phenolic content (TPC), total flavonoid content (TFC), condensed tannin content (CTC) and total isoflavone content in both raw and cooked soymilk as compared to Method 1. Cooking soymilk reduced 14-17% of total phenolic substances. Cooking reduced anticancer capacity of Method-4-prepared soymilk phenolic extract by increasing IC50 value from about 4.9 mg/mL to 6.8 mg/mL. The increases in phenolic compounds and antioxidants produced in Prosoy soymilk by Methods 2 and 4 with simultaneous increases in product solids yield are significant to benefit the soymilk industry and consumer health. Keywords: ProSoy yellow soybean, soymilk processing, phenolics, isoflavones, antioxidant capacity, anti-DU145 prostate cancer proliferation

The success of near-infrared spectroscopy (NIRS) analysis hinges on the precision and robustness of the calibration model. Shallow learning (SL) algorithms like partial least squares discriminant analysis (PLS-DA) often fall short in capturing interrelationships between adjacent spectral variables, and the analysis results are easily affected by spectral noise, which dramatically limits the breadth and depth application of NIRS. Deep learning (DL) methods, with their capacity to discern intricate features from limited samples, are progressively integrated into NIRS. In this paper, two discriminant analysis problems including wheat kernels and Yali pears were used as examples, and several representative calibration models to research the robustness and effectiveness of the model. Additionally, this article proposed a near-infrared calibration model, which is based on gramian angular difference field and coordinate attention convolutional neural networks (G-CACNN). The research results show that, compared with SL, spectral preprocessing has a smaller impact on the analysis accuracy of consensus learning (CL) and DL, and the latter has the highest analysis accuracy in the modeling results of using the original spectrum. The accuracy of G-CACNN in two discrimination tasks is 98.48% and 99.39%, respectively. Finally, This research compared the performance of various models under noise to evaluate the robustness and noise resistance of the proposed method.

This study presents a comprehensive comparative analysis of retrofitting techniques aimed at enhancing the seismic resilience of seismically vulnerable historical buildings. Recognizing the dual objectives of structural safety and architectural preservation, this research evaluates and compares several advanced retrofitting methods, including base isolation, strengthening of masonry, steel bracing systems, Fiber-Reinforced Polymer (FRP) wrapping, and damping devices. Each technique is critically assessed based on its effectiveness in mitigating seismic risks, its compatibility with historical architectural features, and its applicability to various building types. Base isolation is highlighted for its ability to decouple buildings from ground motion, thereby significantly reducing seismic forces and protecting architectural integrity. Strengthening of masonry through the use of fiber-reinforced polymers and steel elements enhances the ductility and strength of masonry walls, making them more resilient to seismic forces. Steel bracing systems are shown to provide essential lateral support, particularly in timber-framed structures, improving overall stability and reducing deformation during earthquakes. FRP wrapping is identified as a versatile technique that strengthens structural elements without compromising aesthetic value, making it suitable for reinforcing concrete and masonry components. Damping devices, including viscous dampers and tuned mass dampers, are discussed for their ability to dissipate seismic energy and control structural vibrations, offering a minimally invasive solution that preserves historical aesthetics. The study also addresses several challenges and research gaps associated with these retrofitting techniques, such as ensuring architectural compatibility, assessing long-term material performance, optimizing cost-effectiveness, and navigating complex regulatory frameworks. By advancing knowledge in these areas, the research aims to foster interdisciplinary collaboration and innovation in the development of retrofitting solutions. Ultimately, this study contributes to the ongoing efforts to safeguard historical buildings against seismic hazards. By leveraging cutting-edge technologies and best practices in structural engineering and architectural conservation, stakeholders can develop sustainable, cost-effective, and culturally sensitive retrofitting strategies that protect valuable cultural heritage for future generations.

Based on the detailed exploration of AI techniques for the early identification of learning difficulties in education, this study underscores the pivotal role of educational data analysis in enhancing student outcomes. Educators can proactively identify and address learning challenges through systematic data collection and analysis, thereby minimizing long-term academic obstacles and emotional stress. The integration of AI, particularly through natural language processing and computer vision technologies, facilitates personalized learning paths and real-time interventions, offering tailored support that maximizes each student's learning potential. These advancements optimize educational resource allocation and foster a more inclusive and effective learning environment, paving the way for future advancements in personalized education and intelligent teaching practices.

For this research we are selected three indicators of wheat: yield (t/ha), producer price (USD/t) and share of the harvested area under wheat in relation to the total land area of country (%). The mentioned indicators were analyzed for the period 2006-2021 in thirty-two European countries. The purpose of the research is to determine which of the mentioned indicators achieve average annual growth/decrease rates, what is the correlation between them, how European countries are grouped with their similarities and differences. The research examines the impact of the COVID-19 pandemic on the mentioned indicators in a two time phases: Phase I, before the pandemic (2006-2019); Phase II, during the pandemic (2020-2021). The methodological approach to the research topic involved the application of descriptive statistics, as the method of principal components analysis (abbr. PCA) with graphics. A positive correlation exists only between the yield of wheat and the share of the harvested area under wheat in the total area of the land (0.291). PCA method showed that countries are grouped differently depending on the observed indicator and the analyzed time phase.

In this paper, we report a comprehensive and consistent annotation of the locus encoding the horse T cell receptor b-chain (TRB), as inferred from the most recent genome assembly. The horse TRB locus spans approximately 1 Mb, making it the largest locus among the mammalian species stud-ied to date, with a significantly higher number of genes related to extensive duplicative events. In the region, 136 TRBV, belonging to 29 subgroups, 2 TRBD, 13 TRBJ and 2 TRBC genes, were iden-tified. The general genomic organization resembles that of other mammals, with a V-cluster of 135 TRBV genes, located upstream of two in-tandem aligned TRBD-J-C clusters, and an inverted TRBV gene at the 3’ end of the last TRBC gene. However, the horse b-chain repertoire would be affected by a high number of non-functional TRBV genes. Thus, we queried a transcriptomic da-taset derived from splenic tissue of a healthy adult horse, using each TRBJ gene as a probe to ana-lyse clonotypes encompassing the V(D)J junction. This analysis provided insights into the usage of the TRBV, TRBD and TRBJ genes and the variability of the juxtaposition region. Our results clearly demonstrated that the horse β-chain constitutes a complex level of variability broadly like that described in other mammalian species.

: In this paper we present an optimization of the planar manufacturing scheme for stretch-free, shape induced metal interconnects to simplify the fabrication with the aim of maximizing the flexibility in the structure regarding to stress and strain. The Formation of trenches between silicon islands are actively used in the lithographic process to create arc shape structures by spin coating resist into the trenches. The resulting resist form is used as a template for the metal lines, which are structured on top. Because this arc shape is beneficial for the flexibility of these bridges. The trench depth as a key parameter for the stress distribution is investigated by applying numerical simulations. The simulated results show that the increase in penetration depth of the metal bridge into the trench increases the tensile load which is converted into a shear Force Q(x), that usually leads to increased strains the structure can generate. For the fabrication the filling of the trenches with resist is optimized by varying the spin speed. Compared to the theoretical resistance, the current-voltage measurements of the metal bridges show a similar behavior and almost every structural variation is capable of functioning as a flexible electrical interconnect in a complete island-bridge array.

Methodologies for future-oriented research are mutually beneficial to highlight different methodological perspectives and proposals for extending higher education didactics towards sustainability. This study explores how different augmented reality applications can enable new ways of teaching and learning. It systematically investigates how student teachers (n=18) in higher education experienced ongoing realities while designing learning activities for a hybrid conference and interconnecting sustainability knowings via didactic modelling and design thinking. This qualitative study aims to develop a conceptual hybrid framework concerning the implications of student teachers incorporating the design thinking and inner transition into their professional work with future-oriented methodologies on didactic modelling for sustainability commitment. With a qualitative approach data was collected during and after a hackathon-like workshop through student teachers’ reflections, post-workshop surveys, and observation field notes. The thematic analysis shed light on transgressive learning and a transition in sustainability mindset through activation of inner dimensions. Findings reinforcing sustainability commitment evolved around the following categories: being authentic (intra-personal competence), collaborating co-creatively (inter-personal competence), thinking long-term-oriented (futures-thinking competence on implementing didactics understanding), relating with creative confidence (values-thinking competence as embodied engagement), and acting based on perseverant professional knowledge driven change (bridging didactics) by connecting theory-loaded empiricism and empirically loaded theory. The results highlight some of the key features of future-oriented methodologies – and approaches to future-oriented methodologies feature collaboration, boundary crossing and exploration – and show the conditions that can support or hinder methodological development and innovation.

Over the past decade, Knowledge bases (KB) have been increasingly utilized to complete and enrich the representation of queries and documents in order to improve the document retrieval task. Although many approaches have used KB for such purpose, understanding how effectively lev-erage entity-based representation still needs to be resolved. This paper proposes a Purely Enti-ty-based Semantic Search Approach for Information Retrieval (PESS4IR) as a novel solution. The approach includes (i) its own entity linking method, (ii) an inverted indexing method, and for document retrieval and ranking, (iii) an appropriate ranking method is designed to take advantage of all the strengths of the approach. We report the findings on the performance of our approach tested by queries annotated by two known entity linking tools, REL and DBpedia-Spotlight. The experiments are performed on the standard TREC 2004 Robust and MSMARCO collections. By using the REL method, for queries whose all terms are annotated and whose average annotation scores are greater than or equal to 0.75, our approach achieves the maximum nDCG@5 score (1.000). Thus, using our approach with any other document retrieval method would be an added value, unless that method achieves the maximum nDCG@5 score for those highly annotated queries.

Nature-based Solutions (NbS) have rapidly been gaining traction across the research, policy, and practice spheres, touted as transformative actions to jointly address biodiversity loss and climate change. However, there are multiple, alternative ways to imagine NbS in those three spheres. To inform the NbS discourses across these three spheres, we critically reflect on the prevailing framing of NbS and consider the potential of a different framing of NbS to support transformations towards regenerative relationships between humans and nature. Such reflection is urgently needed to ensure that research, policy, and practice delivers on the transformative ambitions of NbS. We propose a novel “core framing” of NbS, charting two pathways for how such a framing can support a human value-based transformation – first through influencing individual beliefs and values, and second through the communication and application of the NbS concept in research, policy, and practice. We argue that for NbS to support transformation, it must support a reframing of human-nature relationships, one where the interdependencies between people and nature are recognized as essential for social and environmental well-being. We elaborate on how such a framing is key to support inclusivity and collaboration between diverse research perspectives, policy objectives across scales, and implementation practices, to deliver successful NbS.