Boeing and Airbus developed a special testing procedure to investigate the compressive response of laminates that have been impacted (following standards ASTM D 7137 and DIN 65561). This study focuses on both experimental and numerical analysis of Kevlar plates subjected to compression after impact. To ensure high quality and appropriate mechanical properties, the composite plates were manufactured using autoclaving. The DIN 65561 protocol was followed for all three test systems. Initially, ultrasonic C-scanning was performed on all plates before testing to confirm they were free of any significant defects arising from the manufacturing process. Subsequently, low-energy impact testing was conducted at levels ranging from 0 to 8 Joules. Three specimens were tested at each energy level. After the impact, all specimens underwent ultrasonic C-scanning again to assess the internal delamination damage caused by the impactor. Finally, both pristine and impacted specimens were subjected to compressive testing using the special jig specified in DIN 65561. The compressive impact strength results obtained from these tests were plotted against the delamination area measured by C-scanning. This data was then compared to results obtained from specimens with artificial damage. Semi-empirical equations were used to fit both sets of curves. The same procedure (impact testing, C-scanning, and data analysis) was repeated to investigate the relationship between impact energy and total delamination area. Lastly, finite element modeling was employed to predict the buckling stresses that develop under compression in the impacted systems studied. These modelling approaches have demonstrated good accuracy in reproducing experimental results for CAI tests.

Carbon fiber-reinforced polymer (CFRP), noted for its outstanding properties including high specific strength and superior fatigue resistance, is increasingly employed in aerospace and other demanding applications. This study investigates the interactions between CFRP composites and high-energy lasers (HEL), with continuous wave laser powers reaching up to 120 kW. A novel automated sample exchange system, operated by a robotic arm, minimizes human exposure while enabling a sequence of targeted laser tests. High-speed imaging captures the rapid expansion of a plume consisting of hot gases and dust particles during the experiment. The research significantly advances empirical models by systematically examining the relationship between laser power, perforation times, and ablation rates. It demonstrates scalable predictions for the effects of high-energy laser radiation. Detailed examination of the damaged samples, both visually and via micro-focused computed X-ray tomography, offers insights into heat distribution and ablation dynamics, highlighting the anisotropic thermal properties of CFRP. Compression-after-impact (CAI) tests further assess the residual strength of the irradiated samples, enhancing the understanding of CFRP’s structural integrity post-irradiation. Collectively, these tests improve the knowledge of the thermal and mechanical behavior of CFRP under extreme irradiation conditions. The findings not only contribute to predictive modeling of CFRP's response to laser irradiation but also enhance the scalability of these models to higher laser powers, providing robust tools for predicting material behavior in high-performance settings.

This paper reports an experimental investigation on compression after low-velocity impact response for two lay-up configurations of symmetric CFRP laminated composite specimens obtained by reversing their angle-ply orientation, namely [0/-45/45/90]s versus [90/45/-45/0]s, the impact velocity of the projectile up to the BVID level being subsequently considered. To this aim, a modified Compression-After-Impact (CAI) test device is proposed that involves clamping the specimen's upper and lower edges between two adjustable wide and flat anti-buckling plates through a removable bolt-nut assembly. Such a solution relies on the fact that the specimen's active length is shortened, reducing the risk of global buckling. Besides, the bolts carry part of the load with minor localized bearing damage, provided that the metallic plates act as washers by supporting the bolt-bearing region laterally, thus avoiding crashing failures at the specimens’ loaded edges. With these settings, roughly the same percent decrease in the average values of maximum compression load (i.e., 22%) was recorded for both lay-up configurations impacted up to their BVID threshold, whereas in terms of compressive stiffness behavior, a reduction of 17 % was found for [0/-45/45/90]s specimens compared to 6 % obtained for [90/45/-45/0]s specimens.

Background and objectives Osteoporotic vertebral compression fractures, particularly prevalent among the aging population, constitute a pressing global healthcare challenge. They often are unnoticed until severe pain and disability manifest, making them an underdiagnosed and undertreated condition. Patients who suffer from these fractures not only endure excruciating pain but also face diminished quality of life, impaired mobility, and the risk of respiratory compromise due to altered spinal alignment. The economic repercussions of vertebral compression fractures are substantial. Hospitalization costs, rehabilitation expenses, long-term care, and indirect costs related to lost productivity significantly burden healthcare systems and society at large , offering a promising avenue for enhancing patient outcomes and relieving the healthcare and societal financial strain posed by vertebral compression fractures. Kyphoplasty, a minimally invasive surgical technique, offers rapid pain relief, vertebral height restoration and improved function. Recognizing the importance of early intervention, this manuscript highlights the potential of kyphoplasty in mitigating both clinical and economic consequences. By addressing these fractures more effectively, kyphoplasty may potentially reduce long-term healthcare expenses and indirect costs. Material and Methods 66 randomized patients were divided into 2 treatment groups (kyphoplasty using single balloon and double balloon), analyzing radiographic and clinical parameters during 12 months of follow-up. Results Patients treated with double balloon obtained greater anterior and posterior vertebral height after reduction and a better local vertebral angle. Both groups of patients obtained clinical improvement after treatment (VAS and ODI), with no differences between the groups. Conclusion Patients treated with double balloon kyphoplasty had better radiographic results. This revision manuscript delves into the critical dimensions of these fractures, encompassing demographics, clinical consequences, challenges in diagnosis and management, and their profound economic impact. This manuscript serves to introduce an improved kyphoplasty technique to guide to the multifaceted nature of osteoporotic vertebral compression fractures and their management.

We estimated the risk of blood clots after COVID-19 vaccination accounting for the roles of vaccination in reducing the infection rate, and indirectly lowering the risk of blood clots caused by infection. A self-controlled case series method was used to examine the association between blood clots and COVID-19 vaccination. To deal with the bias due to under-reported infection among non-hospitalized subjects, a case-control study was used to compare the risk of blood clots in infected subjects to control subjects who were hospitalized due to physical injury. We found increased risks of blood clots after vaccination (incidence rate ratio is 1.13, 95% confidence interval (CI): [1.03, 1.24] after the first dose and 1.23, 95% CI: [1.13,1.34] after the second dose). Furthermore, vaccination attenuated the increased risk of blood clots associated with infection (odds ratio (OR) = 2.16, 95% CI: [1.93, 2.42] in unvaccinated versus OR=1.46, 95% CI: [1.25, 1.70] in vaccinated). A causal model was used to explain and weigh up possible risk factors for blood clots after COVID-19 vaccination. After accounting for vaccine efficacy against infection and the protection against infection-associated blood clots, receiving the COVID-19 vaccines decreases the risk of blood clots, especially during high infection rate period.

Recent technological advances have significantly increased the data volume obtained from deep space exploration missions, making the downlink rate a primary limiting factor. Particularly, JAXA’s Martian Moons eXploration (MMX) mission encounters this problem when identifying safe and scientifically valuable landing sites on Phobos using high-resolution images. A strategic approach in which we effectively reduce image data volumes without compromising essential scientific information is thus required. In this work, we investigate the influence of image data compression, especially as it concerns the accuracy of generating the local Digital Terrain Models (DTMs) that will be used to determine MMX’s landing sites. We obtain simulated images of Phobos that are compressed using the CCSDS-120 with integer/float-point discrete wavelet transform (DWT), candidate algorithms for the MMX mission. Accordingly, we show that, if the compression ratio is 70% or lower, the effect of image compression remains constrained, and local DTMs can be generated within altitude errors of 40 cm on the surface of Phobos, which is ideal for selecting safe landing spots. We conclude that the compression ratio can be increased as high as 70%, and such compression enables us to facilitate critical phases in the MMX mission even with the limited downlink rate.

During prolonged standing, insufficient calf muscle pumping accompanies venous stasis and hypertension in the lower legs, resulting in valve dysfunction, venous wall problems, and subsequent inflammation. Compression therapy, which includes medical compression stockings (MCS) and mechanical intermittent pneumatic compression (IPC), is one of the most effective therapeutic interventions for treating chronic venous diseases. This study aimed to investigate the safety and efficacy of IPC and MCS, and the optimal protocol of compression therapy for chronic venous disease. This crossover trial was conducted for healthy, long standing workers (>8 h daily) with leg edema and pain. Four groups were established for each visit: group A (resting after work without MCS), group B (resting after work with MCS), group C (IPC after work without MCS), and group D (IPC after work with MCS). The primary outcome was the visual analogue scale (VAS) score for leg pain. The secondary outcomes were leg volume (mL), circumference (cm), extracellular fluid/total body fluid (ECF/TBF), and extracellular water/total body water (ECW/TBW) through bioimpedance analysis. Outcomes were assessed before work (T0), after work (T1), and 60 minutes after intervention (T2). We included 39 healthy volunteers, aged 30.03±7.56 years. All four groups had significantly increased leg pain after work (T0-1) but improved 60 minutes after intervention (T1-2), particularly group C (decreased VAS by 1.9). When leg swelling was compared at T0 and T1, groups A and C showed significant increases in leg volume and circumference, indicating significant work-induced edema, whereas groups B and D showed no change or even a decrease. After interventions, leg volume and circumference significantly decreased in groups A and C, although groups B and C did not show significant improvement. The ECF/TBF and ECW/TBW of all groups decreased after interventions. Leg pain and edema after prolonged standing in healthy adults were safely and effectively improved by IPC. Although MCS also reduced leg edema immediately after work, it did not show significant improvement in leg pain at T0-1–and T1-2, nor in swelling at T1-2.

End-to-end learned image compression codecs have notably emerged in recent years. These codecs have demonstrated superiority over conventional methods, showcasing remarkable flexibility and adaptability across diverse data domains while supporting new distortion losses. Despite challenges such as computational complexity, learned image compression methods inherently align with learning-based data processing and analytic pipelines due to their well-suited internal representations. The concept of Video Coding for Machines has garnered significant attention from both academic researchers and industry practitioners. This concept reflects the growing need to integrate data compression with computer vision applications. In light of these developments, we present a comprehensive survey and review of lossy image compression methods. Additionally, we provide a concise overview of two prominent international standards, MPEG Video Coding for Machines and JPEG AI. These standards are designed to bridge the gap between data compression and computer vision, catering to practical industry use cases.

Osteoporotic spinal fractures represent an increasingly widespread health problem in our aging society. We aimed to investigate the treatment options for low-energy spinal fractures in the el-derly and their impact on mortality, focusing on surgical stabilization using minimally invasive and open techniques. We evaluated 1356 patients over 50 years of age with compression frac-tures sustained due to low energy trauma treated at a single trauma center. We compared the mortality of patients following stable and operated/non-operated unstable compression frac-tures and the eligibility to surgery using the open and minimally invasive approach. The pa-tients received surgical or conservative care according to severity and eligibility to surgery. The mortality hazard ratio of patients who underwent screw fixation was 1.02 (P > .91), of patients who refused surgery was 1.68 (P < .001) and that of patients with anesthesiological contraindica-tion was 1.57 (P = .08), compared to conservatively treated patients with stable fractures. The dif-ference in mortality between open and minimally invasive surgeries was not significant, but the number of patients eligible for surgery with the minimally invasive procedure was significantly higher (OR: 0.25; P < .001). Spinal stability after fractures may be an important predictor of sur-vival in patients with low-impact fractures.

This study examines the differential impact of proactive and reactive job crafting behaviors on job well-being, drawing from the perspective of boundary theory. The increasing popularity of work connectivity behavior after-hours (WCBA) after work has attracted widespread attention from scholars on the relationship between WCBA and employee well-being. One view suggests that the impact of WCBA is negative, while another view suggests it is positive. Obviously, the impact of (WCBA) on well-being at work is still contradictory. To clarify the complexity of the impact of WCBA on well-being at work, based on boundary theory, we divided WCBA into proactive WCBA (PC) and reactive WCBA (RC), and examined the double-edged sword effect of WCBA on well-being at work, as well as the mediating mechanisms of job control and work-to-home conflict, and the moderated effects of boundary segmentation preferences. This study uses empirical sampling method to collect data from 125 employees for a period of five days for quantitative research. The results show that, first, PC has an inverted U-shaped effect on job control, and job control is negatively related to well-being at work. Thus the mediating effect of job control is significant. Second, RC has a negative impact on job control, and there is also a negative relationship between job control and well-being at work. Therefore, the mediating effect of job control is significant. Third, PC and RC are positively correlated with work-to-home conflict, and work-to-home conflict has a significant positive impact on well-being at work. Therefore, the mediating effect of work-family conflict is significant. Fourth, the study also found that integration preference moderates the relationship between work-to-home conflict and PC on well-being at work, that is, the mediating effect of work-to-home conflict is stronger for employees with low integration preference. This study enriches our understanding of WCBA, PC and RC from the perspective of proactive and passive employee behaviors. The study also provides a new interpretation of the impact of WCBA on well-being at work and offers valuable insights for the sustainable development in digital social transformation and the application of boundary theory and the theory of empowerment-subjugation in achieving the United Nations Sustainable Development Goals. In addition, the study deepens our understanding of the heterogeneous regulatory role played by work-family integration preferences in influencing well-being at work under different types of WCBA.

Background: It has been demonstrated that pressotherapy used post-exercise (Po-E) can influence training performance, recovery, and physiological properties. This study examined the effec-tiveness of pressotherapy on these parameters. Methods: The systematic review and meta-analysis were performed according to PRISMA guidelines. A literature search of MEDLINE, PubMed, EBSCO, Web of Science, SPORTDiscus and ClinicalTrials has been done up to March 2021. Inclusion criteria were: randomized control trials (RCTs) or cross-over studies, mean participant age be-tween 18-65 yrs., ≥ 1 exercise mechanical pressotherapy intervention. The risk of bias was assessed by the Cochrane risk-of-bias tool for RCT (RoB 2.0). Results: 12 studies comprised of 322 partici-pants have been selected. The mean sample size was n = 25. Pressotherapy significantly reduce muscle soreness(Standard Mean Difference;SMD= -0.33; CI = -0.49, -0.18; p < 0.0001; I2 = 7%). Pres-sotherapy did not significantly affect jump height (SMD = -0.04; CI =-0.36, -0.29; p = 0.82). Presso-therapy did not significantly affect creatine kinase level 24-96h after DOMS induction (SMD = 0.41; CI = -0.07, 0.89; p = 0.09; I2 = 63%). Conclusions: Only moderate benefits of using pressotherapy as a recovery intervention have been observed. Results varied between the type of exercise and used protocol. Pressotherapy should only be applied as an additional component of a more compre-hensive recovery strategy. Study PROSPERO registration number- CRD42020189382.

Due to its insensitivity to corrosion, textile CFRP (carbon fibre reinforced polymer) reinforcement enables the construction of thin-walled concrete structures such as shells, vaults and girder webs with minimal concrete cover. In contrast to tensile and flexural behaviour, strutting and compressive membrane action of cracked thin-walled carbon reinforced concrete (CRC) elements and the interaction of compressive stresses with transverse tensile loading have not yet been investigated. While for steel reinforced concrete components, extensive biaxial testing has shown a significant reduction of concrete compressive strength as a function of the lateral tensile stress (compression softening), the effect of biaxial loading on CRC structures has not been quantified yet. However, a different behaviour is expected due to different bond properties of steel and CFRP in concrete, smaller crack spacings and the tendency of the CFRP reinforced concrete for in-plane splitting. This paper presents an extensive experimental campaign for investigation of the influence of transverse tension and cracking on the compressive strength of CRC with refined measurement techniques. Based on a literature review on compressive softening behaviour and conventional test setups for steel reinforced concrete, a novel test setup was developed. The phenomenology of compression softening in CRC as well as the main factors influencing compressive membrane behaviour are highlighted. Based on the experimental findings a constitutive law for compression softening behaviour of CRC is proposed.

(1) Background: Breast cancer-associated lymphedema (BCRL) is a major complication of breast cancer treatment, affects the quality of life of breast cancer survivors who develop it. Manual lymphatic drainage has a beneficial result in combating lymphedema in patients who have undergone breast cancer surgery. The hypothesis consists in complete decongestive therapy reduces the lymphedema at the level of the upper limb on the side of mastectomy. (2) Methods: Twenty-five patients with radical mastectomy and upper limb lymphedema on the mastectomy side were included in this study. Upper limb circumferences were measured with a tape measure at the following levels: metacarpophalangeal joint; distal radioulnar joint; 10 cm distal to lateral epicondyle; 5 cm proximal to elbow joint; 10 cm proximal to lateral epicondyle. (3) Results: Patients received twice weekly manual lymphatic drainage, multi-layer compression bandaging and upper limb muscle stimulation exercises on the mastectomy side twice weekly. The circumference assessed at the level of the metacarpophalangeal joints and distal radio-carpal joint decreased at the final evaluation. Forearm perimetery - 5 and 10 cm distal to the lateral epicondyle the circumference decreased at the final assessment. (4) Conclusions: Patients with breast cancer-related lymphedema should receive comprehensive decongestive therapy in the early stage of lymphedema to achieve rapid clinical results and improved quality of life

We demonstrate a proof-of-principle of simple all-solid-state post-compression setup for low energy, high repetition rate laser pulses, where spectral broadening was performed using a combination of highly nonlinear bulk materials in a simple single pass geometry. 75 fs, 210 nJ pulses from an amplified 76 MHz, 15.7 W Yb:KGW oscillator after sequential spectral broadening in ZnS and YAG samples of 2 mm and 15 mm thickness, respectively, were compressed to 37 fs by means of Gires–Tournois interferometric mirrors. The post-compressed pulses with an average power of 11.47 W demonstrated reasonable spatial-spectral homogeneity of the beam with the spectral overlap parameter V>83% and good beam quality with Mx2=1.28 and My2=1.14.

Broadcasting a message from one to many processors in a network corresponds to concurrent reading on a random access shared memory parallel machine. Computing the trees of a forest, the level of each node in its tree and the path between two nodes are problems that can easily be solved with concurrent reading in a time logarithmic in the maximum height of a tree. Solving such problems with exclusive reading requires a time logarithmic in the number of nodes, implying message passing between disjoint pairs of processors on a distributed system. Allowing concurrent reading in parallel algorithm design for distributed computing might be advantageous in practice if these problems are faced on shallow trees with some specific constraints. We show an application to LZC-compressed file decoding, whose parallelization employs these computations on such trees for realistic data. On the other hand, zipped files do not have such advantage since they are compressed by the Lempel-Ziv sliding window technique.

This study discusses the experimental assessment of the in-plane mechanical behavior of a multi-leaf stone masonry wall built from cut stone and reinforced with metal connectors (cramps and dowels). The wall, inspired by conventional multi-leaf stone walls, is meant for use in modern stone masonry buildings. The wall is constructed from two parallel load-bearing walls with a cavity between them, which aims to conceal the installation and insulation needed in modern buildings. The load-bearing walls are connected with cramps and dowels at certain intervals so that the wall works as a single section against horizontal and vertical loads. To characterize the in-plane behavior of the proposed wall, compressive, triplet, and diagonal compression tests were conducted to investigate the compressive strength, shear strength, modulus of elasticity, stiffness, ductility, and energy absorption of the wall. Compared with dry and mortar joint walls, the use of dowels increased the initial shear capacity of the wall by 11 and 19 times, respectively. The application of cramps without curving channels inside the individual stone elements decreased the compressive strength by 18%. The energy absorption of the designed walls with metal connectors was substantially increased to that of the specimens representing conventional stone walls. The results obtained show the applicability of the wall due to its higher shear strength and minimal drop in compressive strength, which is within acceptable limits.

Abstract: Increasing physical activity (PA) and personal and social values are two of the greatest demands in the current educational system. This study examined the effect of a hybrid pro-gramme based on the Personal and Social Responsibility Model and Gamification. A total of 58 students (13.89 years old, SD = 1.14) in two groups (Experimental and Control) participated dur-ing a complete academic year. Motivation, physical activity and sedentary behaviour were as-sessed though questionnaires. Physical fitness was evaluated using previously validated field tests. The results showed significant differences over time between EG and CG in afterschool physical activity (APA) at the weekend (p = 0.003), sedentary time (p = 0.04) and speed-agility (p = 0.04). There were no significant differences in motivation. Regarding the intervention, speed-agility (p = 0.000), strength (p = 0.000), agility (p = 0.000), cardiorespiratory fitness (p = 0.001), APA-weekend (p = 0.000), APA-week (p= 0.000) and sedentary time (p = 0.000) increased signifi-cantly in the EG. Speed-agility (p = 0.000), APA-weekend (p = 0.03) and sedentary time (p = 0.008) increased in the CG. The use of this hybrid program can be useful to produced improvements in physical fitness, physical activity and sedentary hevaviours. The use of a hybrid program based on teaching personal and social responsibility and gamification strategies, produced improvements in physical fitness, physical activity and sedentary behavior, but not in motivation variables. Further research is demanded in order to contrast this relevant findings due to the potential drawbacks and diversity found in the scientific literature among model-based practice.

Desiccation tolerance appeared as the key adaptation feature of photoautotrophic organisms for survival in terrestrial habitats. During the further evolution, vascular plants developed complex anatomy structures and molecular mechanisms to maintain the hydrated state of cell environment, which essentially increased their ability to sustain water deficit and dehydration. However, the role of the genes encoding the mechanisms behind this adaptive feature in the higher vascular plants is restricted to the dehydration protection of spores, seeds and pollen, whereas the mature vegetative stages became sensitive to desiccation. During maturation, orthodox seeds lose up to 95% of their water and successfully enter dormancy. This feature allows seeds maintaining their viability even under strongly fluctuating environmental conditions. The mechanisms behind the desiccation tolerance are activated at the late seed maturation stage and are associated with the accumulation of late embryogenesis abundant proteins (LEA proteins), small heat shock proteins (sHSP), non-reducing oligosaccharides, and antioxidants of different chemical nature. The main regulators of maturation and desiccation tolerance onset are abscisic acid and protein DOG1, which control the network of transcription factors, among which are LEC1, LEC2, FUS3, ABI3, ABI5, AGL67, PLATZ1, PLATZ2. This network is complemented by epigenetic regulation of gene expression by methylation of DNA, post-translational modifications of histones and chromatin remodeling impact on seed desiccation tolerance and longevity. Moreover, orthodox seeds are able to maintain desiccation tolerance during germination up to the stage of radicle protrusion. This time point is critical in the process of seed development, as the seeds lose desiccation tolerance at this moment.

The cardioprotective effects of volatile anesthetics versus total intravenous anesthesia (TIVA) are controversial, especially in patients undergoing non-cardiac surgery. Using current generation high-sensitivity cardiac troponin (hs-cTn), we aimed to evaluate the effect of anesthetics on the occurrence of myocardial injury after non-cardiac surgery (MINS). From February 2010 to December 2016, 3555 patients without preoperative hs-cTn elevation underwent non-cardiac surgery under general anesthesia. Patients were grouped according to anesthetic agent; 659 patients were classified into a propofol-remifentanil total intravenous anesthesia (TIVA) group, and 2896 patients were classified into into a volatile group. To balance the use of remifentanil between groups, a balanced group (n=1622) was generated with patients who received remifentanil infusion in the volatile group, and two separate comparisons were performed (TIVA vs. volatile and TIVA vs. balanced). The primary outcome was occurrence of MINS, defined as rise of hs-cTn I ≥ 0.04 ng/mL within postoperative 48 hours. The secondary outcomes were 30-day mortality, postoperative acute kidney injury (AKI), and adverse events during hospital stay (mortality, type I myocardial infarction (MI), and new-onset arrhythmia). In propensity-matched analyses, the occurrence of MINS was lower in the TIVA group compared to the volatile group (OR 0.642; 95% CI 0.450-0.914; p = 0.014). However, after balancing the use of remifentanil, there was no difference between groups in the risk of MINS (OR 0.832; 95% CI 0.554-1.251; p-value = 0.377). There were no significant associations between the two groups in type 1 MI, new-onset atrial fibrillation, in-hospital and 30-day mortality before and after balancing the use of remifentanil. However, the incidence of postoperative AKI was lower in the TIVA group (OR 0.362; 95% CI 0.194-0.675; p-value = 0.001). After balancing the use of remifentanil, volatile anesthesia and TIVA showed comparable effects on MINS in patients undergoing non-cardiac surgery without preoperative myocardial injury. Further studies are needed on the benefit of remifentanil infusion.

In this work, we have developed a non-ordinary state-based peridynamic model for multiple crack initiation and propagation due to compression-compression fatigue load. In each loading cycle, the fatigue loading is redistributed among the peridynamic solid body, leading to the progressive fatigue damage initiation and propagation in an autonomous fashion. The proposed fatigue model parameters are firstly validated by 3D numerical benchmark tests, and then it is applied to simulate widespread fatigue damage evolution of the aircraft wing corner box. The modified constitutive damage model has been implemented into the peridynamics framework at finite strain. Furthermore, the criterion algorithm from multiple initiation to propagation is discussed. It is shown that the numerical results obtained from peridynamics simulations are in general agreement with those from the experiment data. The comparison of experimental and numerical results indicates that the proposed non-ordinary state-based peridynamics fatigue model has the ability to capture the multiple crack initiation and propagation and other features of the aluminium alloy material.

This study numerically analyzed the effect of composition and temperature and oxygen concentration changes on the selfignition characteristics of n-heptane/methane blended fuels in order to cope with development of alternative fuels and international environmental regulations. CHEMKIN-PRO is used as the analysis program and the LLNL model is used as the reaction model. The numerical results revealed that on autoignition and ignition delay time were sensitive to changes in fuel composition and oxygen concentration. As the methane ratio increases, OH radicals causing ignition are delayed in generation and the concentration is lowered, thus longer the ignition timing. The oxygen concentration in the mixed fuels are changed to simulate the exhaust gas recirculation and a numerical analysis in then performed. As the oxygen concentration decreases, the ignition delay time longer because the nitrogen gas acts as a thermal load in the combustion chamber.

Currently, for the serious air pollution and global warming effect caused by the substance released from the present vehicle, it is expected that the regulatory requirements for the emission will become more stringent. A new concept of the combustion technology that can reduce the NOx and PM related to combustion is urgently needed. To cope with such social demands, many developed countries are efforts to develop the environment friendly vehicle engine at the national lever in order to satisfy with strengthening emission control. As a main combustion technology among new combustion technology for the new generation engine, the homogenous charge compression engine (HCCI) is expanding its application range by employing multiple combustion mode, catalyst, direct fuel injection and partially premixed combustion. In this paper, a multi-injection method in order to apply the HCCI combustion method without mainly altering engine specifications and practicality by referring to the results of the HCCI engine was investigated. Applied with forced charging, exhaust gas recirculation (EGR) and compression ratio change, it was evaluated to the possibility of securing optimum fuel economy and emission reduction in the IMEP 0.8 MPa range.

Community co-creation is increasingly crucial to the building of sustainable societies. Communities must proactively and independently create value chains in the face of many wicked problems. However, practical frameworks and tools for facilitating community co-creation require further development. As such, for this paper, we propose a theoretical framework for analyzing community co-creation value chain mechanisms based on a narrative review of literature on Collective Impact, social impact assessment, and Community Capital from the perspective of collective impact, a framework with a fair amount of previous research. We argue for the importance of applying knowledge of social impact assessment, particularly for the collective impact conditions of common agenda and shared measurement system. We discuss its relationship with the Theory of Change and the use of systems thinking to mitigate the subjectivity and arbitrariness of design thinking. Furthermore, we emphasize the value of employing the community capital concept as a framework for analyzing interrelationships among elements. By integrating multiple concepts, we enhance the collective impact framework and outline potential avenues for future research on analyzing and effectively implementing co-creation value chain mechanism in a community-based approach.

The primary goal of picture compression is to reduce the amount of unused image data while still storing or transmitting it in a format that is appropriate. The compression of raw binary data is quite different from the compression of a picture, and these differences may be rather substantial. In light of this, compression is often regarded as an essential technique for the purposes of both data storage an d transmission in order to mitigate the excessive amounts of data that are generated by these images. In order to transmit enormous datasets, particularly for the purposes of telemedicine and teleradiology, one needs a significant amount of storage capacity as well as an expansive network. As a result, compression is an important aspect of medical imaging. In addition to the importance of compression, the quality of the photos themselves is also an essential factor in the success of analysis. In addition to this, the amount of time necessary to compress the photographs before sending them should be reduced.

Multiagent technologies give a new way to study and control complex systems. Local interactions between agents often lead to group synchronization also known as clusterization, which usually is a more rapid process in comparison with relatively slow changes in external environment. Usually, the goal of system control is defined by the behaviour of a system on long time intervals. When these time intervals are much longer than the time of cluster formation, clusters may be considered as new variables in a ``slow'' time model. We call such variables ``mesoscopic'' to emphasize their scale laying between the level of the whole system (macroscopic scale) and the level of individual agents (microscopic scale). Thus, it allows us to reduce significantly the dimensionality of a system by omitting considerations of each separated agent, so that we may hope to reduce the required amount of control inputs. Thus, we are often able to consider a system as a collection of ``flowing'' (morphing) clusters emerged form behaviour of a huge amount of individual agents. In this paper, we contrast such approach to the one where a system is considered as a network of elementary agents. We develop a mathematical framework for analysis of cluster flows in multiagent networks and use it to analyze the Kuramoto model as an attracting example of a complex networked system. In this model, a clusterization leads to sparse representation of dynamic trajectories in the whole quantized state space. With that in mind, compressive sensing allows to restore the trajectories in a high-dimensional discrete state space based on significantly lower amount of randomized integral mesoscopic observations. We propose a corresponding algorithm of quantized dynamic trajectory compression. It could allow us to efficiently transmit the state space data to a data center for further control synthesis. The theoretical results are illustrated for a simulated multiagent network with multiple clusters.

An effective on-board cloud detection method in small satellites would greatly improve the downlink data transmission efficiency and reduce the memory cost. In this paper, an ensemble method combining a lightweight U-Net with wavelet image compression is proposed and evaluated. The red, green, blue and infrared waveband images from Landsat-8 dataset are trained and tested to estimate the performance of proposed method. The LeGall-5/3 wavelet transform is applied on the dataset to accelerate the neural network and improve the feasibility of on-board implement. The experiment results illustrate that the overall accuracy of the proposed model achieves 97.45% by utilizing only four bands. Tests on low coefficients of compressed dataset have shown that the overall accuracy of the proposed method is still higher than 95%, while its inference speed is accelerated to 0.055 second per million pixels and maximum memory cost reduces to 2Mb. By taking advantage of mature image compression system in small satellites, the proposed method provides a good possibility of on-board cloud detection based on deep learning.

This paper is the continuation of a previous study, which highlighted some inconsistencies in the RILEM guidelines for the interpretation of the diagonal compression test. Although improved compared to the ASTM guidelines, in fact, the RILEM guidelines underestimate the state of hydrostatic stress induced by the diagonal compression test at the center of the wallette. The new interpretation of the diagonal compression test proposed in this article shows that the RILEM guidelines actually underestimate both the hydrostatic and the deviatoric stress states at the center of the wallette. The new formulation complies with the linear elastic theory and allows us to use the the diagonal compression test to identify the three elastic coefficients of masonry. In particular, it allows the identification of the Poisson ratio, which instead takes on a conventional value in the RILEM and ASTM guidelines. The difference of one order of magnitude between the conventional and proposed Poisson’s ratio is in agreement with the experimental results on another brittle material, namely concrete. Finally, the new proposal fills the gap between the results provided by the two tests usually performed to identify the shear behavior of masonry: the diagonal compression test and the shear-compression test.

A numerical method has been presented to simulate hypervelocity impacts into metal targets. The target is a rectangular prism and positioned at various inclined angles relative to the impact direc-tion, while four different projectile such as square prism, triangular prism, truncated cone and ogival shape are chosen. With this numerical model we aim to evaluate the risk of orbital debris impacting space structures in the design of shield systems for protection against hypervelocity impacts in space. To explore the geometric influences on hypervelocity impact, various projec-tile/target configurations are simulated using the Material Point Method. The Johnson–Cook plas-ticity model with a failure criterion is employed alongside Mie-Grüneisen's equation of state. Our analysis results reveal that the structure of debris cloud formations, scattering behavior of the ejected particle from both front and rear faces and penetration depth measures are significantly influenced by the projectile shape and impact angles.

In the context of the economic and political uncertainty associated with the 2019-nCoV pandemic, it is necessary to determine the socio-psychological factors involved in the transformation of the behavior of insurance consumers under the influence of a biogenic threat. This study measures financial anxiety and its impact on the insurance behavior of Russian citizens. The correlation, comparative, and regression analyses of the financial anxiety of Russian citizens cover three stages of observation: before the start of the 2019 nCoV pandemic (“FA up to 19 nCoV; N = 766), during the period of quarantine measures announced in Russia in March 2020 (“FA 19-nCoV-1”; N = 856), and after the relaxation of quarantine measures at the end of April 2020 (“FA 19-nCoV-2”; N = 963).Psychological analysis data were obtained from the online survey “Financial anxiety (in the context of insurance)”. The questionnaire is psychometrically reliable and easy to use. It includes five measurement scales: MR1—Physical manifestations of financial incentive anxiety, MR2—With money shortages and financial uncertainty, MR3—The value of insurance coverage, MP4—Financial Confidence, and MR5—Perception of insurance and investment risks. It was found that Russian citizens consider it important to have insurance coverage for a “rainy day”, and they showed confidence in the insurance market during the biogenic crisis. However, unfortunately, during the 19-nCoV-1 and 19-nCoV-2 periods, Russian citizens did not feel financially secure, unlike in the period before 19-nCoV. Women showed high scores for physical manifestations of financial anxiety and low financial confidence in the future, in contrast to men, regardless of the observation period.

In the context of economic and political uncertainty associated with the 2019-nCoV pandemic, it is necessary to determine the socio-psychological factors in the transformation of the behavior of insurance consumers under the influence of the biogenic threat. This study is devoted to measuring financial anxiety and its impact on the insurance behavior of Russian citizens. Correlation, comparative and regression analyzes of financial anxiety of Russian citizens cover three stages of observation: before the start of the 2019 nCoV pandemic (“FA up to 19 nCoV; N = 766), during the period of quarantine measures announced in Russia in March 2020 (“ FA 19- nCoV-1 "; N = 856) and after the relaxation of quarantine measures at the end of April 2020 (" FA 19-nCoV-2 "; N = 963). Psychological analysis data were obtained from the online survey "Financial anxiety (in the context of insurance)". The questionnaire is psychometrically reliable and easy to use, including 5 measurement scales: MR1. Physical manifestations of financial incentive anxiety, MR2. With money shortages and financial uncertainty, MR3. The value of insurance coverage, MP4. Financial Confidence, MR5. Perception of insurance and investment risks. Russian citizens considered it important to have insurance coverage on a “rainy day” and showed confidence in the insurance market during the biogenic crisis. But, unfortunately, Russian citizens during the 19-nCoV-1 and 19-nCoV-2 periods did not feel financially secure in the future, unlike the period before 19-nCoV. ”Women showed high scores for physical manifestations of financial anxiety and low financial confidence in the future, in contrast to men, regardless of the observation period.

The diffusion coefficients of ions are measured in a microchip filled with a cationic charged 3D hydrogel in order to study the effect of cationic charged 3D hydrogel on the diffusivity of ions. In this study, poly-diallyl-dimethyl-ammoniumchloride (poly-DADMAC) is used to produce a 3D hydrogel. Four different fluorophores are used in the 3D hydrogel rhodamine 6G, rhodamine-BSA, fluorescein isothio-cyanate (FITC) and FITC-BSA. The rhodamine 6G and rhodamine-BSA are positively charged (cations), while fluorescein isothio-cyanate (FITC) and FITC-BSA are negatively charged (anions). Two widely used techniques which are short time diffusivity measurement technique and long time diffusivity measurement techniques are used to measure the diffusion coefficients. For the short time measurement, Fluorescence recovery after photo-bleaching (FRAP) is used by a 3D confocal microscope. For the long time measurement, fluorescence images are taken for 11 days to observe a pure diffusivity without any convective movement. As a result, the diffusivity of the cations was found to be lower than that of the anions in the cationic charged hydrogel.

In directional forming processes such as rolling and extrusion, the microstructure is strongly elongated in the forming direction. This results in a preferred alignment of the crystal orientations of the initially randomly oriented grains. These preferred orientations – the texture – and elongations of the grains are the cause of the material anisotropy. This anisotropy leads to phenomena such as earing, which occur during further forming processes, e.g., during deep drawing of sheet metal. Considering anisotropic properties in numerical simulations allows to investigate the effects of texture-dependent defects in forming processes and the development of possible solutions. Purely phenomenological models for modelling anisotropy work by fitting material parameters or applying measured R-values in experiments which are applied to all elements of the part and remain constant over the duration of the simulation. In contrast, methods such as the Visco-Plastic Self-Consistent (VPSC) model, which has been used in this work, provide a deeper insight into the development of the material microstructure. By experimentally measuring the initial texture and using it as an initial condition for the simulations, it is possible to predict the evolution of the microstructure and the resulting effect on the mechanical properties during forming operations. The results of the simulations with VPSC show good qualitative agreement with tests typically used for rolled stock.

Abstract: We present the Hellenic orogenic belt`s main geological structure and architecture of deformation, trying to reach a better interpretation of its geotectonic evolution during the Alpine orogeny. We based on our recent studies and experience about the deformational history of the Hellenides but also on the more modern views, published by other colleagues, concerning the Alpine geotectonic reconstruction of the Hellenides. The structural evolution started during the Permo-Triassic with the continental breaking of the Pangea super-continent and the birth of the Neotethyan ocean realm. Bimodal magmatism and A-type granitoid intrusions accompanied the initial stages of the continental rifting, followed by Triassic-Jurassic multiphase shallow- and deep-water sediment deposition on both formed continental margins. These margins were the Apulian margin, containing the Pelagonia, at the western part of the Neotethyan ocean and the European margin, containing continental parts of the Serbo-Macedonian and Rhodope massifs (upper Vertiskos-Kimi and middle Sidironero-Kerdylia units), at the eastern part of the Neotethyan ocean. Deformation and metamorphism are recorded in six main deformational stages from the Early-Middle Jurassic to the present day, getting started with an Early-Middle Jurassic Neotethyan intra-oceanic subduction and ensimatic island arc magmatism. Compression, nappe stacking, calc-alkaline magmatism and high-pressure metamorphic events related to subduction processes alternated successively through time with extension, orogenic collapse, medium- to high-temperature metamorphism, adakitic and calc-alkaline magmatism and partly migmatization, related to uplift and exhumation of deep crustal levels as tectonic windows or metamorphic core complexes. An S- to SW-ward migration of the dynamic peer compression vs. extension is recognized during the Tertiary Alpine orogenic stages in the Hellenides. In any case extension and crustal uplift follow compression and nappe stacking or compression and exten-sion act simultaneously at different parts of the orogen. We suggest that all ophiolite belts in the Hellenides originated from a single source and this was the Neotethyan Meliata/Maliac-Axios/Vardar ocean basin, parts of which obducted during the Mid-Late Jurassic on both continental margins, Apulian`s (containing Pelagonia) and European`s (containing units of Serbo-Macedonian/Rhodope nappes stack), W-SW-ward and E-NE-ward, respectively. In this case, the ophiolite nappes should be considered as far-traveled nappes on the Hellenides continental parts associated with the deposition of Middle-Late Jurassic ophiolitic mélanges in basins at the front of the adjacent ophiolite thrust sheets. The upper limit of the ophiolite emplacement is the Mid-Upper Jurassic, Callovian-Oxfordian, as shown by the deposition of the Kimmeridgian-Tithonian Upper Jurassic sedimentary carbonate series on the top of the obducted ophiolite nappes. The suture zone between the Pelagonian nappe and the External Hellenides as part of the Apulia plate has been dated about coeval in time with the Paleocene-Eocene to Oligocene SW-ward over thrusting (between 56 Ma and 32 Ma), along the Nestos thrust zone, of the Serbo-Macedonian/Rhodope Sidironero-Kerdylia unit on the tectonically lower-most Rhodope Pangaion unit. In this sense, the Nestos shear zone in the Rhodope province continues until the suturing between Pelagonian and External Hellenides and is the same with this. Therefore, the lower-most Rhodope Pangaion unit could be regarded, as the continuation of the marginal part of the Apulian plate (External Hellenides) that was underthrusted during the Paleocene-Eocene below the unified Sidironero-kerdylia unit and the Pelagonian nappe, following the Paleo-cene-Eocene subduction and closure of a small ocean basin at the western of the Pelagonian (Pindos-Cyclades ocean basin). Was preceded by the Late Cretaceous subduction of the Axios/Vardar ocean remnants below the European continental margin and the final closure of the Axios/Vardar ocean during the Paleocene-Eocene, which were associated with the overthrusting of the European origins Vertiskos-Kimi nappe on the Sidironero-Kerdylia nappe and subsequently the final collision of the European margin and Pelagonian fragment. In this scenario should be assumed, that the true Vardar/Axios suture zone should originate in the deep further to the East between the Rhodope units in the northern Rhodope province, while the Axios/Vardar zone in its today outcrops position should be considered as allochthonous. Subsequently, during synorogenic Oligocene-Miocene extension, the lower-most Rhodope Pangaion unit exhumed as a metamorphic core complex below the Serbo-Macedonian/Rhodope nappes, which were successively exhumed, from the higher to the middle, during Paleocene-Eocene and Eocene-Oligocene extension, respectively. A retreating subduction zone associated with rollback of the subducted lithosphere under the Pelagonian and the other Internal Hellenides nappes stack and/or slap break off and mantel delamination could well explain the Tertiary synorogenic extensional tectonics in the Internal Hellenides, taking place simultaneously with compression in the External Hellenides and the Hellenic foreland or accretionary wedge.

The study focuses on the crucial aspect of lossless compression for FAST pulsar search data. The deep generative model PixelCNN, stacking multiple masked convolutional layers, achieves neural network autoregressive modeling, making it one of the most excellent image density estimators. However, the local nature of convolutional networks causes PixelCNN to concentrate only on nearby information, neglecting important information at greater distances. Although deepening the network can broaden the receptive field, excessive depth can compromise model stability, leading to issues like gradient degradation. To address these challenges, the study combines causal attention modules with residual connections, proposing the Causal Residual Attention Module to enhance the PixelCNN model. This innovation not only resolves convergence problems arising from network deepening but also widens the receptive field. It effectively utilizes global features, particularly capturing vertically correlated features prominently present in subgraphs of candidates. This significantly enhances its capability to model pulsar data.In the experiments, the model is trained and validated using the HTRU1 dataset. The study compares the average negative log-likelihood score with baseline models like GMM, STM, and PixelCNN. The results demonstrate the superior performance of the our model over other models. Finally, the study introduces the practical compression encoding process by combining the proposed model with arithmetic coding.

The need to recycle carbon fibre reinforced composite polymers (CFRP) has grown significantly to reduce the environmental impact generated by their production. To meet this need, thermoreversible epoxy matrices have been developed in recent years. This study investigates the performance of an epoxy vitrimer made by introducing a metal catalyst (Zn2+) and its carbon fibre composites focusing on the healing capability of the system. The dynamic crosslinking networks endow vitrimers with interesting rheological behaviour, the capability of the formulated resin (AV-5) has been assessed by creep tests. The analysis showed increased molecular mobility above a topology freezing temperature (Tv). However, the reinforcement phase inhibits the flow capability reducing the flow. The fracture behaviour of CFRP made with the vitrimeric resin has been investigated by Mode I and Mode II tests and compared with the conventional system. The repairability of the vitrimeric CFRP has been investigated by attempting to recover the delaminated samples, which yielded unsatisfactory results. Moreover, the healing efficiency of the modified epoxy composites has been assessed by using the vitrimer as an adhesive layer. The joints were able to recover about 84% of the lap shear strength of the pristine system.

The volume of vehicular traffic in large cities has increased in recent years, the devices that collect vehicular GPS data such as cameras, GPS receivers and others generate millions of records at every instant of time generating problems in processing and storage of these data which becomes important for researchers. Intelligent Transportation Systems perform vehicle monitoring and control by collecting GPS trajectories, this large volume of information is necessary to have an optimal storage process. Its processing by means of compression techniques and simplification algorithms allow to reduce the necessary storage space. This paper presents a GPS trajectory simplification algorithm that considers noise reduction, point simplification and analysis of road network information. The results obtained on two data sets from the cities of California and Beijing are satisfactory, achieving a higher compression ratio without affecting data quality

Model understanding is critical in many domains, particularly those involved in high-stakes decisions, i.e., medicine, criminal justice, and autonomous driving. Explainable AI (XAI) methods are essential for working with black-box models such as Convolutional Neural Networks. This paper evaluates the traffic sign classifier of Deep Neural Network (DNN) from the Programmable Systems for Intelligence in Automobiles (PRYSTINE) project for explainability. The results of explanations were further used for the CNN PRYSTINE classifier vague kernels` compression. After all, the precision of the classifier was evaluated in different pruning scenarios. The proposed classifier performance methodology was realised by creating the original traffic sign and traffic light classification and explanation code. First, the status of the kernels of the network was evaluated for explainability. For this task, the post-hoc, local, meaningful perturbation-based forward explainable method was integrated into the model to evaluate each kernel status of the network. This method enabled distinguishing high and low-impact kernels in the CNN. Second, the vague kernels of the classifier of the last layer before the fully connected layer were excluded by withdrawing them from the network. Third, the network's precision was evaluated in different kernel compression levels. It is shown that by using the XAI approach for network kernel compression, the pruning of 5% of kernels leads only to a 1% loss in traffic sign and traffic light classification precision. The proposed methodology is crucial where execution time and processing capacity prevail.

Background: Mucoadhesive polymers represent a major part of site-specific and localized retention strategies in oral drug delivery. Present research was designed to synthesize and characterize a novel mucoadhesive carbohydrate polymer (thiolated gum ghatti; TGG) which was further employed to fabricate mucoadhesive tablets of domperidone using an industrially viable compression coating technique. Methods: Thiolation of gum ghatti was achieved by the ester formation (esterification) between hydroxyl group and carboxyl group of gum ghatti and thioglycolic acid. Results: TGG was characterized by various physico-chemical techniques such as FTIR, XRD, SEM and DSC techniques. In rheological studies, the observed viscosities of pure gum-mucin were 45.45 and 71.75 mPas and that of thiolated gum were 78.7 and 112.58 mPas respectively in water and simulated gastric fluid. Signifi-cant increase in viscosity for thiolated gum may be attributed to increased macromolecular interactions responsible for enhanced mucoadhesive potential of thiolated gum. In-silico studies corroborate the role of mucin gum interaction and energetic stabilization for en-hanced mucoadhesion properties of thiolated gum. Ex-vivo mucoadhesion strength of gum ghatti and thiolated gum ghatti coated tablets was found to be ranging between 4.67± 0.79 to 8.99± 0.75 g and 11.76± 1.34 to 18.83± 2.07 g respectively. Conclusion: Thiolated gum ghatti may be regarded as a promising polymer for developing different mucoadhesive drug delivery systems.

Nonlinear compression of narrow-band (Δ ≈ 0.2 cm-1) 20 ns KrF laser pulses in SF6 at 10 atm and CH4 at 50 atm pressure was studied. Both SBS and SRS optically phase conjugated backward reflected radiation was registered with energy reflectivity 10−14% in SF6 and CH4. In SF6 SBS pulses gradually shortened from 10 ns to 2−3 ns with pumping decrease to the SBS threshold ~ 10 mJ, while the SRS pulse had the shortest length of 30−60 ps for the maximal pumping of 120 mJ and broadened near the SRS threshold of ~30 mJ. For the SRS pulse energy ~ 2 mJ peak power 5×107 W was tenfold higher than the pump power. The theoretical model predicted a soliton-like SRS pulse compression to a temporal length of the order of vibrational relaxation time. There was no pulse compression of backward SBS and SRS radiation in CH4, while in the forward direction SRS pulses shortened to 3−4 ns at reduced pumping.

This paper examines the Business Model (BM) from a socioeconomic system perspective to discern key factors, and understand its interactions resulting in the Scaling of Social Impact (SSI) in Social Entrepreneurship (SE). Previously, studies have explained the importance of BM in relation to SE. However, there is a lack of empirical studies on how BM’s transitions through participation of various actors result in SSI. This research applies qualitative analysis on a single case study of a Japanese social startup, “mymizu”, the first water refill application platform in Japan. The findings show that collaboration amongst different stakeholders on the initial phase of the BM could increase awareness of responsible consumption, convert into actual users for sustainability, and change their behavior. Secondly, members of the society could take on dual roles, both as users and collaborators in the BM, which results in an exponential scaling effect of the social impact. This paper contributes towards adding a participatory stakeholder (PS) to the ecosystem of SSI and building a “regenerative” BM that is relevant in SE towards sustainability.

Concurrent waves of Coronavirus disease, Ebola virus disease, avian influenza A and black fungus are jeopardizing the lives in some parts of Africa and Asia. From this point of view, this review aims to summarize both socio-economic and public health implications of these parallel outbreaks along with their best possible management approaches. Various online databases were used to collect the necessary information regarding these outbreaks. Based on the reports published and analyses done so far, the long-lasting damages caused by these simultaneous outbreaks on global socio-economical and public health status can be conceived from the past experiences of outbreaks, especially the COVID-19 pandemic. Moreover, prolonged restrictions by the local government may lead to food insecurity, global recession, and an enormous impact on the mental health of people of all ages, specifically in developing countries. Such overwhelming effects already have been reported to be declining national growth of the economy as well as increasing political insecurity and shortage of basic needs. Although various actions have already been taken including vaccination, clinical management, and further research, social distancing, and lockdown, etc. to improve the situation, the emerging variants and associated genetic mutations may make the containment difficult worsening the situation again. Considering the current mutational dynamics of the pathogens and the past experiences, perpetual preparedness along with updated clinical management backed by epidemiological studies and innovating scientific effort are inevitable to combat the simultaneous waves of multiple infectious diseases.

.With the increasing use of carbon fiber reinforced plastics in various area, carbon fiber composites based on prepregs have attracted attention in industries and academia research. However, prepreg manufacturing processes are costly, and the strength of structures varies depending on the orientation and defects (pores and delamination). For non-contact evaluation of internal defects, we proposed lock-in infrared thermography to investigate orientation angles after a compression test. We also conducted a drop-weight impact test to study the behaviour of the composites after impact according the fibers orientation for composite fabricated using unidirectional carbon fiber prepregs. Using CAI tests, we determined the residual compressive strength and confirmed the damage modes using a thermal camera. The results of the drop weight impact tests show that the specimen laminated at 0° suffered the largest damage because of susceptibility of the resin to impact. In contrast, the specimens oriented in of 0°/90° and +45°/–45° directions transferred more than 90% of the impact energy back to the impactor because of the lamination of fibers in the orthogonal directions. Furthermore, the specimens that underwent complete damage in the impact tests were subjected to the lock-in method and showed internal delamination and cut fibers. With the finite elements analysis, the damage of each ply could be observed. Moreover, the temperature differences in the residual compression tests were not significant.

The problem of normal impact of a rigid sphere onto a Maxwell viscoelastic solid half-space is considered. The first-order asymptotic solution is constructed in the framework of Hunter’s model of viscoelastic impact [Hunter, S. C., 1957. Energy absorbed by elastic waves during impact. Journal of the Mechanics and Physics of Solids, 5(3), 162–171.]. In particular, simple analytical approximations have been derived for the maximum contact force and the time to achieve it. A linear regression method is suggested for evaluating the instantaneous elastic modulus and the mean relaxation time from a set of experimental data collected for different impactors and impact velocities.

Floor mats are commonly used to improve the impact sound performance of existing homes, but the actual reduction does not consistently appear depending on the test-bed conditions used to determine it. Therefore, this study evaluated the effects of the environmental conditions of the test-bed on the impact sound reduction performance of different floor mats. The Korean Industrial Standard, KS F 2865, specifies the measurement method in the test room and sets the thickness range of the available target floor structure from bare slab 120 mm to 210 mm. The evaluation method is ∆?, which is the difference in standardized impact sound levels before and after the installation of the floor finishing material. In this study, a total of eight types of floor mats were tested in four different test-beds according to KS F 2865. The impact sources used were tapping, bang machines and a rubber ball to consider both light-weight and heavy-weight impact sounds. The results were derived as impact sound reduction performance for each frequency band and a single number quantity. The results showed that light impact sound had a similar minimum reduction characteristic of at least 38 dB, regardless of the floor structure on which the mat was installed. However, the heavy-weight impact sound showed different tendencies depending on the floor mat and the characteristics of the floor structure of the test-bed when a bang machine and a rubber ball were used. In particular, the reduction by the bang machine showed less than half the tendency of the reduction by the rubber ball, and the tendency of the heavy-weight impact sound to be reduced depending on the floor mat was maintained, but the reduction differed depending on the test bed. The reduction was larger in the box-type test room than in the real-life type test room, and among the box-type test rooms, the one with a thicker bare slab showed a relatively larger reduction. In addition, the reliability of the measurement results was discussed through the correlation analysis between the single number quantities depending on the thickness of the bare slab of the test-beds.

We propose a neural-network-based watermarking method that introduces the quantized activation function that approximates the quantization of JPEG compression. Many neural-network-based watermarking methods have been proposed. Conventional methods have acquired robustness against various attacks by introducing an attack simulation layer between the embedding network and the extraction network. The quantization process of JPEG compression was replaced by the noise addition process in the attack layer of the conventional methods. In this paper, we propose a quantized activation function that can simulate the JPEG quantization standard as it is in order to improve the robustness against the JPEG compression. Our quantized activation function consists of several hyperbolic tangent functions and is applied as an activation function for neural networks. Our network was introduced in the attack layer of ReDMark proposed by Ahmadi et al. to compare it with their method. That is, the embedding and extraction networks had the same structure. We compared the usual JPEG compressed images and the images applying the quantized activation function. The results showed that a network with quantized activation functions can approximate JPEG compression with high accuracy. We also compared the bit error rate (BER) of estimated watermarks generated by our network with those generated by ReDMark. We found that our network was able to produce estimated watermarks with lower BERs than those of ReDMark. Therefore, our network outperformed the conventional method with respect to image quality and BER.

Currently there are fewer depth models applied to pepper picking detection, while the existing generalized neural networks have problems such as large model parameters, long training time, and low model accuracy.In order to solve the above problems, this paper proposes a Yolo-chili target detection algorithm for chili pepper detection. First, the classical target detection algorithm yolov5 is used as a benchmark model, and an adaptive spatial feature pyramid structure combining the attention mechanism and the idea of multi-scale prediction is introduced to improve the model's detection effect on occluded peppers and small target peppers. Secondly, a three-channel attention mechanism module is introduced to improve the algorithm's long-distance recognition ability and reduce the interference of redundant testers. Finally, the quantized pruning method is used to reduce the model parameters and realize the lightweight processing of the model. Applying the method to the homemade chili pepper dataset, the AP value of chili pepper reaches 93.11%; the accuracy rate is 93.51% and the recall rate is 92.55%.The experimental results show that yolo-chili is able to achieve accurate and real-time pepper detection under complex orchards.

This study presents a methodology to fabricate Ti6Al4V cylindrical compacts with a highly porous core and dense shell with the purpose to mimic the bone microstructure. Compacts with different core diameters were obtained by conventionally press and sintering. Large pores were created with the aid of pore formers. Sintering kinetics was determined by dilatometry, whereas characterization was performed by X-ray computed tomography. Also, permeability was evaluated on the 3D microstructure and the mechanical strength was evaluated by compression tests. Results indicated that sintering is constraint by the different densification rates of the porous and dense layers. Nonetheless, defectless compacts were obtained due to neck bonding between Ti6Al4V particles. Large pores were located in the designed core with similar pore size distribution. Permeability increased following a power law as a function of the pore volume fraction. Stiffness of bilayer components was driven by the porous core, meanwhile, the strength resulted from the combination of both layers. Bilayer materials obtained showed a permeability and mechanical properties, as well as admissible strain (σy /E) similar to those of human bones.

The effects of 1%~5% cold compression on the mechanical properties, microstructure and residual stress of 7050 aluminum alloy were investigated, and the results were applied to the complex die forging with stiffener structure. The results show that with the increase of cold compression, the tensile strength of forging decreases gradually, but the conductivity and fracture toughness of the forging have little change. TEM microstructure shows that with larger cold compression (5%), the dislocation density was relatively higher, which promoted the precipitation and growth of precipitated phases at positions with higher dislocation density during aging process. The ultrasonic tests of residual stress show that with the increase of cold compression, the residual stress in the forging decreases first, and then increases when cold compression reaches 5%. The results of the die forging of 7050 aluminum alloy with bar structure show that the residual stress of the die forging is obviously eliminated after 2-4% cold compression, and the deformation after machining is obviously less than of the uncompressed forgings. The combination of bar and web is more beneficial to the uniform distribution of residual stress of the die forging with bar structure.

Considering that a fair coin has two sides and a cylindrical edge, the probability that it would fall on its edge is calculated, yielding the probability of heads or tails less than 50%. Theoretical models for a static case and for five dynamic cases, without and with rebounds, show that there is a small probability that the coin does not fall on its head or tail, depending on initial toss conditions, the coin geometry and conditions of the coin and landing surfaces. For the dynamic model with rebounds, it is found that the probability that a 50 Eurocent coin thrown from a normal height with common initial velocity conditions and appropriate surface conditions will end up on its edge is in the order of one against several thousand.

We have modelled the energy consumption of prototype and real buildings under present and future climatic conditions with the EnergyPlus model to develop a better understanding of the relationship between changing climate conditions and energy demand. We have produced detailed meteorological information with 50 meters of spatial resolution through dynamical downscaling process combining regional, urban and computational fluid dynamics models which include the effects of the buildings on urban wind patterns. The city of Madrid has been chosen for our experiment. The impact on energy demand and their respective economic cost are calculated for year 2100 versus 2011 based on two IPCC climate scenarios, RCP 4.5 (stabilization of emissions) and RCP 8.5 (not reduction of emissions). Findings show that climate change will have a significant impact on the energy demand for buildings. Space heating demand will be increased by the RCP 4.5 and cooling demand will be increased for the RCP 8.5 in the analysed buildings.

The advent of remote work has ushered in a new era of economic transformation, redefining the dynamics of local economies, and unleashing the multiplier effect on a national scale. This abstract explores the profound implications of remote work on local economies, dissecting how the multiplier effect operates within a nation's economic landscape. The multiplier effect is a fundamental economic concept that highlights how changes in spending and investment can create a ripple effect, leading to a magnified impact on an economy. This concept gains new significance in the context of remote work, as it triggers a chain reaction of economic activities that radiate from remote workers to their local communities. The increased flexibility and reduced geographical constraints of remote work have reshaped the allocation of resources. The continued reliance on remote work may lead to a reduction in demand for commercial real estate in urban centers, necessitating adaptive urban planning strategies. In conclusion, the rise of remote work has initiated a transformative era for local economies, driven by the multiplier effect. By amplifying the impacts of spending and investment, remote work fosters job diversification, innovation, and infrastructure development within communities. As remote work continues to reshape the landscape of work and life, understanding and harnessing its multiplier effect remains paramount for policymakers, businesses, and local communities alike. The multiplier effect is a concept in economics that illustrates how changes in spending can lead to larger impacts on a nation's economy through a chain reaction of economic activities. It demonstrates that an initial injection of spending, whether from government expenditure, investment, or consumption, doesn't just have a one-time impact. Instead, it sets off a series of interconnected spending and income-generation processes that result in a larger overall increase in economic activity. t's important to note that the multiplier effect can work in reverse as well. If there's a decrease in spending, it can lead to a decrease in economic activity and income through the same chain reaction process. This concept highlights the interconnected nature of economic activities and emphasizes the significance of changes in spending patterns on a nation's overall economic health. The magnitude of the multiplier effect is influenced by factors such as the marginal propensity to consume (the proportion of additional income that households spend), leakages (savings and taxes that reduce the multiplier effect), and the extent to which additional spending creates additional production capacity within the economy. Understanding the multiplier effect is essential for policymakers, as it helps them gauge the potential impacts of changes in fiscal and monetary policies on the economy.

Climate change represents a major threat to lotic freshwater ecosystems and their ability to support the provision of ecosystem services. England’s chalk streams are in a poor state of health, with significant concerns regarding their resilience, the ability to adapt, under a changing climate. This paper aims to quantify the effect of climate change on hydroecological response, the health of the river, for the River Nar, a SSSI in the south-east of England. To this end, we apply a coupled hydrological and hydroecological modelling framework, with the UKCP09 probabilistic climate projections serving as input (A1B high emissions scenario). Results show that, from 2021 to the end of the century, hydroecological response becomes more heterogeneous. Despite the limited range of the functional feeding groups on the baseline, the River Nar has been able to adapt to extreme events due to inter-annual variation. In the future, this variation is greatly reduced, raising real concerns over the resilience of the river ecosystem under climate change. These new insights into the health of the River Nar, and chalk streams more generally, highlights the necessity of further study and the real need to for changed river management practices.

In the present work we have studied the short-term edaphic recovery of a burned pine forest of Pinus pinaster Aiton in Cerro del Castillo (Sierra de Guadarrama, Central Spain) in which a hydrological-forestry restoration was being carried out after the fire occurred in July 2022. For this purpose, variations in physicochemical properties (conductivity, relative humidity, organic matter and pH) and collembolan communities were analyzed by comparing the soils of a natural pine forest and a burned pine forest during the 24 weeks after the fire in 3 different samplings. With the data obtained, a series of diversity indices were calculated and statistical analyses such as ANOVA, hierarchical classification and principal component analysis were developed, with the aim of understanding in greater depth the recovery of collembolan populations, the changes in these physicochemical variables and the relationships between both parameters. This study shows how the fire reduced the amount of organic matter and water, and increased soil pH and conductivity, affecting edaphic fauna populations. In the short term, there was an increase in relative humidity and a decrease in electrical conductivity. The edaphic fauna communities of the burned pine forest increased their diversity and equity without reaching the values of the natural pine forest. At the specific level, however, the springtail populations matched the richness and even reached a very slightly higher Shanon-Wiener diversity index than that the natural pine forest populations in just 24 weeks. Finally, it was observed that the samples from the burned pine forest with recovered collembolan populations had the closest physicochemical parameters to those of the natural pine forest.

This research is aimed at determining the characteristics of the current level of entrepreneurial potential of the Three Seas Initiative (3SI) countries, the ability to overcome the consequences of extraordinary events, such as COVID-19 and prospects for the return to an accelerated development once the destabiliser of the economic system, the coronavirus pandemic, has ceased. Eurostat, World Bank and the World Economic Forum data for 2015-2019 were used for the purpose of the research. The research was divided into three stages, i.e. assessment of economic development on the basis of a synthetic ratio of economic anchor development, for which a relative benchmark method based on spatial median (so-called L1 median or Weber point) was used, identification of conditions for the development of entrepreneurial capacity and statistical analysis showing the correlation between economic anchor measures and selected factors of the 3SI countries economic development. Our study found that the entrepreneurial capacity of the 3SI countries in 2015-2019 was determined by nine characteristics, belonging to six areas, i.e. local economy, demographic situation, social situation, trade exchange, innovation and tourism economy. The entrepreneurial potential of the 3SI countries was spatially diversified, and its development was determined, among others, by the entrepreneurial activity of residents (entrepreneurship index) and the conditions for running a business.

Objective: To analyze the clinical and economic impact of community-onset urinary tract infections (UTI) caused by extended-spectrum beta-lactamase (ESBL)-producing Klebsiella pneumoniae requiring hospitalization. Methods: A retrospective cohort study included all adults with UTI caused by K. pneumoniae admitted to a tertiary care hospital in Barcelona, Spain, between 2011 and 2015. Demographic, clinical and economic data were analyzed. Results: One hundred and seventy-three episodes of UTI caused by K. pneumoniae were studied; 112 were non-ESBL-producing and 61 ESBL-producing. Multivariate analysis identified ESBL production, acute confusional state associated with UTI, shock, and time to adequate treatment as risk factors for clinical failure during the first 7 days. Economic analysis showed differences between ESBL-producing and non-ESBL-producing K. pneumoniae for the total cost of hospitalization per episode (mean 6,718 € vs 3,688 € respectively). Multivariate analysis of the higher costs of UTI episodes found statistically significant differences for ESBL production and time to adequate treatment. Conclusion: UTI caused by ESBL-producing K. pneumoniae requiring hospitalization, and time to adequate antimicrobial therapy are associated with worse clinical and economic outcomes.

Large-scale deep learning models have produced significant results in underwater visual image target detection. However, deploying these models on underwater embedded devices poses a series of issues and challenges. Firstly, underwater devices have limited communication capabilities and carry relatively short supply of energy, resulting in constrained computing power for edge devices. Secondly, the large scale of deep neural networks creates a conflict in power demands with unmanned underwater equipment. Thirdly, insufficient underwater light and turbid water quality will lead to degradation problems in the images acquired by the device. In this paper, we build an offline system to complete the task of underwater scene target recognition. This paper introduces several innovations: 1) The new YOLO-TN model is developed by compressing the target recognition model based on YOLO-V5. The model use a model compression algorithm replace the YOLO-V5’s backbone network with a lightweight network, then perform parameter pruning on the model detection head, while reduce the size of the input image. The model uses a Teacher-guided Neural Architecture Search method based on YOLO-V5, named as YOLO-TN. 2)A method for constructing and processing real underwater environment data sets is designed. The datasets are all captured using underwater unmanned vehicles in real underwater environments, addressing issues present in existing underwater datasets, such as unbalanced target volume and single-image environment. Experimental results demonstrate that the YOLO-TN model significantly reduces the model size while maintaining the original recognition accuracy. Furthermore, it achieves 28.6 FPS on embedded devices, which is 12 times that of the original model.

A single paragraph of about 200 words maximum. For research articles, abstracts should give a Ultra-high performance concrete (UHPC) has gained worldwide popularity because of its notable mechanical response. This research studied the compressive strength, modulus of elasticity, and flexural tensile strength of UHPC. Batches were made with the addition of steel and PVA fibers using a standard procedure defined in the research. The experimental data from the compressive strength test was analyzed in the Statistica 10 software to investigate the fibers' influence on UHPC's mechanical properties. An analysis of the elastic modulus prediction was carried out according to international standards. It was found that the normalized equations for the elastic modulus are not adequate for its estimation. The statistical analysis indicated that the range of fiber quantities analyzed did not significantly affect the compressive strength and the elastic modulus. Regarding the optimized mix, its flexural tensile strength indicates that the fiber content must be higher for UHPC to be suitable for structural use.

As the fast growth of information technology (IT), the safety of image transmission and the storing of images are increasingly concerned. Traditional image encryption algorithms have certain limitations in transmission and security, so there is an urgent need for a secure and reliable image encryption algorithm. A universal compression sensing (CS) image encryption (IE) algorithm based on DNA-triploid mutation (DTM) is presented in this paper. Firstly, by using CS algorithm an image is compressed while obtaining a range of chaotic sequences by iteration of chaotic map. Then DNA sequences are generated by encoding the image, and based on the DTM, new mutant DNA sequences are generated according to specific rules. Next, the chaotic sequences are operated at the DNA level to do confusion and diffusion operations on the image to ensure the security of the data. At last, DNA decoding is carried out to obtain the compressed-encrypted image. Both simulation experiments and performance tests fully show that a high level of security and reliability of the proposed algorithm in protecting image privacy is achieved.

Background:Fontan completion is the last stage of univentricular repair, which drains the inferior vena cava against gravity to a higher-pressure pulmonary arterial circulation. The passivity and anti-gravity nature of this circulation render a failing Fontan, not an uncommon encounter, twenty years ago, Rodefeld and colleagues, decided to explore the feasibility of vascular pumps to support the passive nature of Fontan circulation, and since then, trials are still ongoing, and we aimed through this review to wrap up the results of these trials. Methods:A literature review has been conducted, to identify any in vivo or in vitro trial of a Fontan assist device. Several outcome parameters determined whether the trial will be included or not in this review, including, the flow rate of a pump if applicable, the number of compressions per minute if a compression device has been used, the resultant flow rate, the inferior and superior vena cava pressures, associated with each setting of the respective device, and any evidence of hemolysis or clotting within the circuit. Results:A total of ten trials have been included, with 23 different settings. Three designs have been identified, out of which two fall within the pump design, namely the connecting chamber and the intravascular pump designs; only one trial explored the possible use of a compression device. The commonest design encountered in in-vivo trials was the intravascular pump (67%). No reports of significant hemolysis or thrombosis were found. An increasing flow rate beyond 5L/min was associated with a negative outcome in the connecting chamber design, increasing upstream pressure in the SVC, while intravascular pumps did not display this limitation. Conclusion:Univentricular heart patients are a relatively small population, with very extensive needs, despite twenty years of trials, no study has yet concluded the optimal design or settings for a Fontan assist device. In this review, we identified that the intravascular pump remains the most practical design, due to its easy mode of insertion, and that it is not faced with the limitation or risk of increasing upstream resistance. There is still a long way to conclude its use as other designs such as compression devices have not yet been fully studied.

A novel concept of a finned piston system is presented and analyzed where the compression heat is continuously extracted from the compression chamber. The resulting compression characteristic moves in direction of an isothermal process, reducing so the temperature of the compressed fluid in the compression chamber and reducing the necessary mechanical work for the process. The finned piston concept consists in an integrated heat exchanger inside of the chamber and being constituated of imbricated flat fins placed on the stator part and on the mobile piston. The internal heat exchange surface is strongly increased in comparison with a classical piston/cylinder. The energetic performance of the new system is evaluated with the help of simulation. Pressures, forces and temperature of the compressed gas are simulated as well as the mechanical work needed. The different curves are compared with adiabatic and isothermal characteristics.

Purpose: Metastatic spinal cord compression (MSCC) is a severe complication of cancer that can lead to irreversible neurological impairment, necessitating prompt recognition and intervention. This retrospective, single-center study aimed to determine the prognostic factors and survival rates among patients presenting with MSCC secondary to lung cancer. Methods and Materials: We identified 74 patients with epidural metastases-related spinal cord compression and a history of lung cancer, through the electronic database of Medway Maritime Hospital in United Kingdom (UK), spanning the period from April 2016 to September 2021. Among them, 39 were below 55 years old, while 35 were aged 55 years or older, whereas 24 patients were diagnosed with small cell lung cancer (SCLC), and 50 patients had non-small cell lung cancer (NSCLC). Results: The median overall survival (OS) was 5.5 months, with 52 out of 74 patients dying within 6 months of the diagnosis of MSCC. For the entire cohort, the statistically significant variables on multi-variate analysis were: cancer type (NSCLC had improved OS), number of involved vertebrae (one to two vertebrae involvement had improved OS) and time taken to develop motor deficits (≤10 days to develop motor deficits had worsened OS). For the NSCLC cohort, the statistically significant variables on multivariate analysis were: molecular alterations (patients with epidermal growth factor receptor (EGFR) mutation), pre-treatment ambulatory status, Eastern Cooperative Oncology Group (ECOG) performance status, and time taken to develop motor deficits. Conclusions: Within the entire cohort, patients diagnosed with NSCLC and spinal metastases affecting one to two vertebrae exhibited enhanced OS. Within the NSCLC subgroup, those with EGFR mutations, who were ambulatory, and possessed an ECOG performance status of 1-2, demonstrated improved OS. In both the entire cohort and NSCLC subgroup, the development of motor deficits within a period of ≤10 days was associated with poorer OS.

Total hip arthroplasty (THA) is one of the most successful orthopedic procedures and is highly effective in improving function and quality of life. However, after discharge patients commonly experience edema, which can lead to health consequences and lower quality of life. For these rea-sons, the aim of this study is to evaluate the effectiveness of a specific intermittent leg pneumatic compression on lower limb edema and physical outcomes in patients after total hip arthroplasty, compared to standard conservative treatment. A total of 47 patients were enrolled and randomly allocated into two groups: the pneumatic compression group (PG=24) and the control group (CG=23). We evaluated thigh and calf circumferences, knee and ankle range of motion, pain and walking autonomy. Our results showed a greater reduction in thigh and calf circumference for PG (p<0.001), while other outcomes were similar for the two groups (p>0.05). The combination of standard therapy with pneumatic leg compression was more effective in reducing lower limb edema, thigh, and calf circumferences compared to the use of standard treatment. Our results suggest that pressotherapy treatment is a valuable and efficient option for managing lower limb edema and preventing VTE after THA.

Collapsibility is an inherent characteristic of loess, which is often treated by adding industrial materials such as cement and lime in engineering, it seriously damages the reclamation performance of soil. Degradable calcium lignosulfonate (CLS) has a good prospect in balancing soil stabilization and environmental protection. Therefore, this paper evaluates the collapsibility and mechanical characteristics of CLS improved loess based on the collapsibility test, grey correlation analysis, and unconfined compressive strength test. The results show that when the content is 3%, the stabilization effect is most obvious, and the collapsibility coefficient can be reduced by more than 95%. The order of grey correlation degree of collapsibility on each index is moisture content, void ratio, dry density, and CLS content from large to small. The unconfined compressive strength increases rapidly in the first 14 days and then decreases with the content. When the content is too high, the strength of improved loess is lower than that of plain loess. Combined with SEM, microstructure parameters, and X-ray diffraction analysis, the carbonate minerals can play the role of filling pores and connecting soil particles, which reduces the grain size of mineral composition and the thickness of the electric double layer and makes the structure more compact. The research results have scientific significance and application value for the ecological modification research and engineering application of soil.

Mesoscale imperfections, such as pores and voids, can strongly modify the properties and the mechanical response of materials under extreme conditions. Tracking the material response and microstructure evolution during void collapse is crucial for understanding its performance. In particular, imperfections in ablator materials, such as voids, can limit the efficiency of the fusion reaction and ultimately hinder ignition. To characterize how voids influence the response of materials during dynamic loading and seed hydrodynamic instabilities, we have developed a tailored fabrication procedure for designer targets with voids at specific locations. Our procedure uses SU-8 as a proxy for ablators materials and hollow silica microspheres as proxy for voids and pores. By using photolithography to design the targets’ geometry, we demonstrate precise and highly reproducible placement of a single void within the sample, which is key for a detailed understanding of its behavior under shock compression. This fabrication technique will benefit high-repetition rate experiments at x-ray and laser facilities. Insight from shock compression experiments will provide benchmarks for the next generation of microphysics modelling.

Solar assisted hybrid cooling systems are promising for the energy saving of refrigeration systems. In most cases, the solar thermal gain is only able to power the heat-driven process of facilities in part of the working period. Therefore, the reduction of compressor power strongly depends upon the duration of heat-driven processes, which has not been addressed properly. Motivated by such knowledge gap, the thermodynamic understanding of solar assisted hybrid cooling systems is deepened through considering the duration in heat-driven processes. Three absorption-compression integrated cooling cycles were taken as examples. It is found that optimal parameters, e.g., inter-stage pressure and temperature, corresponding to various performance indicators trend to be identical, as the duration of heat-driven processes is taken into account. Furthermore, the optimal parameter for different working conditions was obtained. It is displayed that the dimensionless optimal intermediate temperature of layout with the cascade condensation process varies slightly, e.g., 4%, for different conditions. Moreover, the fall of compressor power in entire working periods is nearly independent upon the intermediate temperature. The paper is favorable for the efficient design and operation of solar assisted hybrid cooling systems.

The QBIT theory is an attempt toward solving the problem of consciousness based on empirical evidence provided by various scientific disciplines including quantum mechanics, biology, information theory, and thermodynamics. This theory formulates the problem of consciousness in the following four questions: (1) What is the nature of qualia? (2) How are qualia generated? (3) Why are qualia subjective? (4) Why does a quale have a particular quality or meaning?In sum, the QBIT theory proposes that (1) when a pack of quantum information is compressed beyond a certain threshold, a quale is generated; (2) a quale is a superdense pack of maximally entangled qubits in a pure state; (3) when information-theoretic certainty of a system about an external stimulus exceeds a particular level, the system becomes conscious of that stimulus; (4) subjectivity of consciousness is due to the fact that maximally entangled pure states are private and unshareable.

Most of the existing studies conducted on FRP-confined concrete considered circular and square concrete columns, while limited studies were on columns with rectangular sections. The studies have confirmed that the circular cross-sections exhibited higher confinement effectiveness, whereas in the case of non-circular cross-sections the efficiency of FRP confinement decreases with an increase of the sectional aspect ratio and there is no significant increase, particularly for columns with the aspect ratio of 2.0. As recently suggested by the researchers, to significantly increase the effectiveness of FRP-confinement for these columns is by modifying a rectangular section to an elliptical or oval section. According to the literature, most of the existing confinement models for FRP-confined concrete under axial compression have been proposed for columns with circular and rectangular cross-sections. However, modeling the axial strength and strain of concrete confined with FRP in elliptical cross-sections under compression is most limited. Therefore, this paper provides new expressions based on limited experimental data available in the literature. For a sufficient amount of FRP-confinement, the threshold value was proposed to be 0.02. Finally, the accuracy of the proposed model was verified by comparing its predictions with the same test database, together with those from the existing models.

Software-based ultrasound imaging systems provide high flexibility that allows easy and fast adoption of newly developed algorithms. However, the extremely high data rate required for data transfer from sensors (e.g., transducers) to the ultrasound imaging systems is a major bottleneck in the software-based architecture, especially in the context of real-time imaging. To overcome this limitation, in this paper, we present a Binary cLuster (BL) code, which yields an improved compression ratio compared to the exponential Golomb code. Owing to the real-time encoding/decoding features without overheads, the universal code is a good solution to reduce the data transfer rate for software-based ultrasound imaging. The performance of the proposed method was evaluated using in vitro and in vivo data sets. It was demonstrated that the BL-beta code has a good stable lossless compression performance of 20 ~ 30% while requiring no auxiliary memory or storage.

Many academics are critical of the current publishing system, but it is difficult to create a better alternative. This review relates to the Sciences and Social Sciences, and discusses the primary purpose of academic journals as providing a seal of approval for perceived quality, impact, significance, and importance. The key issues considered include the role of anonymous refereeing, continuous rather than discrete frequency of publications, avoidance of time wasting, and seeking adventure. Here we give recommendations about the organization of journal articles, the roles of associate editors and referees, measuring the time frame for refereeing submitted articles in days and weeks rather than months and years, encouraging open access internet publishing, emphasizing the continuity of publishing online, academic publishing as a continuous dynamic process, and how to improve research after publication. Citations and functions thereof, such as the journal impact factor and h-index, are the benchmark for evaluating the importance and impact of academic journals and published articles. Even in the very top journals, a high proportion of published articles are never cited, not even by the authors themselves. Top journal publications do not guarantee that published articles will make significant contributions, or that they will ever be highly cited. The COVID-19 world should encourage academics worldwide not only to rethink academic teaching, but also to re-evaluate key issues associated with academic journal publishing in the future.

The existence of insecurity in a state necessitates immediate government attention and action as it poses a risk to human life and property and impedes socio-economic development. The study aims to evaluate insecurity and its impact on socio-economic development in Oyo state. It will also determine the major causes of insecurity problems and offer data that can help develop effective security strategies and policies. The study population consisted of residents who were randomly selected from the Ibarapa North Local Government Area of Oyo State, Nigeria. The descriptive survey method was adopted and analyzed with the Chi-square technique. According to this research, there is a negative correlation between insecurity and the state's socio-economic development. The study recommends good governance and inclusive government policies to curb insecurity and ensure the state's socio-economic development.

As we are aware Information Technology had its cutting-edge lifestyle from the overdue sixties of the remaining century whilst the Arpanet become introduced, funded with the aid of using the branch of protection of the USA. After that, the IT enterprise has come a protracted manner to its cutting-edge form in which its miles gambling a dominant function in each sphere of life. It has made innovative modifications in facts amassing and dissemination and worldwide communication. It is growing into a surely paperless painting environment. Also, we can now ship a message very without difficulty to everywhere withinside the international in seconds. From a schooling factor of view, we can have a digital elegance in which the teacher ought to take a seat down in any part of the arena and his college students scattered in all exceptional elements of the arena via video convention with the presentation of look at substances in addition to query and solution sessions. A health practitioner now sitting in any part of the arena ought to carry out a surgical procedure in which the affected person is mendacity in some other part of the arena. These work examples display where we stand these days compared to what has become 1/2 of a century back. But as we recognize, nothing on this international is only correct as the whole thing has a darkish side. In this paper, we might speak about the deserves and demerits of enforcing IT globally and in which we are heading withinside the future.

The effect of the COVID-19 pandemic in a developing country like Bangladesh is enormous. A research conducted by South Asian network of Economic Modelling predicted that the pandemic could double the poverty. But it is not that only the socioeconomic condition is dropping in Bangladesh, the impact of COVID-19 pandemic is manifold. The poor condition of Bangladesh's health sector has also been exposed due to the pandemic. People are not getting proper treatment due to lack of isolation beds, oxygen, ICU etc. The health sector of Bangladesh is not much developed and now with this pandemic it has become impossible to provide treatment facility for all the patients. Education sector, which is the backbone of a country,has also been greatly affected by the pandemic. We know that different types of cultural occasions are an inherited tradition of Bangladesh, COVID-19 have not even spared these traditions, all the cultural programes and festivals have been cancelled due to this pandemic.In this paper, our aim is to present the present status of all these sectors.

The aim of this study was to examine the post-injury psychological impact looking for to avoid sources of health issues. We have analyzed differences in the stress, anxiety and depression levels between male and female football players who have suffered at least one injury during the last season played respect to similar players who have not been injured. A descriptive cross-sectional design was used. The participants were 187 football players and data on the player’s injuries were collected. A Self-reported Questionnaire collected number, type and severity of injuries sustained during the previous sports season (twelve months), and also the player’s current situation being injured or not injured. To evaluate the psychological variables, the DASS-21 questionnaire was used. Results indicated that the male injured players presented anxiety levels higher than those who were non-injured. When we observe the female players’ data, the stress levels of the non-injured ones are higher than those of the injured players. Regarding the non-injured athletes, results showed that the female non-injured players presented values in anxiety higher than those corresponding to the non-injured male players. Thus, sport injury affects mental health issues such as anxiety and stress, and in a different way regarding gender.

This paper presents laboratory devices on which experimental measurements were carried out to prove the validity of the assumption about the reduction of vibrations transmitted to the conveyor belt structure generated by the impact forces of falling material grains in the places of transfer or on the hoppers of conveyor belts. In order to limit damage to the conveyor belts caused by the impact of the sharp edges of material grains, conveyor belts are supported by impact rollers or impact rubber rods in the places of transfers and on the hoppers of belt conveyors. The flattened ends of the impact rollers are inserted into the grooves of steel brackets installed on the supports of the fixed conveyor idlers of a conventional design. In this paper, a special modification of the fixed conveyor idler is presented, which consists of inserting plastic brackets into the structurally modified roller axle holders of the fixed conveyor idler. Measurements were carried out on the first laboratory device, which showed that the specially modified fixed conveyor idler resulted in a higher damping of up to 15% of the impact forces of the falling weight on the rubberized hoop of the impact roller shell compared to the conventional fixed conveyor idler design. Measurements carried out on the second laboratory device show that the effective vibration velocity values detected at the points where the impact roller axis fits into the fixed roller table holder, i.e. points B and D, are higher than when using plastic brackets, up to 6% for a 108 mm diameter roller, compared to steel impact roller brackets.

Xyleborus beetles, a diverse group of ambrosia beetles, present significant challenges to forestry and agriculture due to their damaging burrowing behavior and symbiotic relationships with fungi. This review synthesizes current knowledge on the biology, ecology, and management of Xyleborus. We explore the beetles' life cycle, reproductive strategies, habitat preferences, and feeding habits, emphasizing their ecological and economic impacts. Control and management strategies, including preventive measures, chemical and biological control, and integrated pest management (IPM), are critically evaluated. Recent advances in molecular genetics and behavioral studies offer insights into genetic diversity, population structure, and host selection mechanisms. Despite progress, managing Xyleborus effectively remains challenging. This review identifies future research needs and highlights innovative control methods, such as biopesticides and pheromone-based trapping systems.

Cardiopulmonary resuscitation (CPR) is a widely practiced lifesaving skill. Conventional CPR is based on manual chest compressions and delivering mouth-to-mouth breaths. There has been advancement in biomedical technology over the last few decades which has led to the introduction of new techniques and devices in CPR as well. In light of these advancements, we propose SMEAR (Standard, Mechanical, ECMO Assisted, Augmented virtual and Remote) classification system to provide structured overview from traditional to novel methods and devices. The standard or Manual CPR, widely practiced by the general public during out-of-hospital cardiac arrests, combines active chest compressions with or without mouth breathing. However, to enhance CPR’s efficacy, various mechanical devices have been developed, encompassing Active Chest Compression, Passive Decompression, and those integrated with Automated External Defibrillators. Feedback sensor-equipped devices, include the Metronome, Accelerometer, Barometer, and Triaxial Field Induction. Mechanical devices, classified by their compression mechanisms, can be isolated – like the Piston-driven, Load-distributing, and Active Compression-Decompression (ACD) – or combined, as in ACD-ITV (Impedance Threshold Device), ACD-IAC (Interposed Abdominal Compression), and ACD-ITV-EECP (Enhanced External Counter Pulsation). Beyond mechanics, Extracorporeal CPR offers veno-arterial Extracorporeal Membrane Oxygenation in refractory cardiac arrest and can improve outcomes. Augmented Virtual Reality usage in training and provision of CPR is at the early stages. It has the potential of expanded usage in training public to provide high-quality CPR. A provider can be remotely guided step by step via telephone or smartphone applications, ensuring continuous support until professional assistance arrives.

The article delves into the crucial realm of compressing hydrogen in its gaseous state, a pivotal process for enhancing its viability in both civil and industrial sectors. The study initiates by providing a concise overview and comparison of diverse hydrogen storage methodologies, laying the groundwork with an in-depth analysis of hydrogen's thermophysical properties. It scrutinizes plausible configurations for hydrogen compression, aiming to strike a delicate balance between energy consumption, predominantly derived from the fuel itself, and the requisite number of compression stages. Notably, to render hydrogen storage competitive in terms of volume, pressures of at least 350 bar are deemed essential, albeit at an energy cost amounting to approximately 10% of the fuel's calorific value. Multi-stage compression emerges as a crucial strategy, not solely for energy efficiency, but also to curtail temperature rise, with an upper limit set at 200°C. This nuanced approach is underlined by the exploration of compression levels commonly cited in the literature, particularly 350 bar and 700 bar. Ultimately, the study advocates for a three-stage compression system as a pragmatic compromise, capable of achieving high-pressure solutions while keeping compression work below 10 MJ/kg, a threshold indicative of sustainable energy utilization.

With recent advancements in network technology and spread of Internet, use of social network services and Internet of Things devices has flourished, leading to a continuous generation of large volumes of graph stream data, where changes, such as additions or deletions of vertices and edges occur over time. Additionally, owing to the need for efficient use of storage space and security requirements, graph stream data compression has become essential in various applications. Even though various studies on graph compression methods have been conducted, most of them do not fully reflect the dynamic characteristics of graph streams and complexity of large graphs. In this paper, we propose a compression scheme using provenance data to efficiently process and analyze large graph stream data. It obtains provenance data by analyzing graph stream data and builds a pattern dictionary based on this to perform dictionary-based compression. By improving the existing dictionary-based graph compression methods, it enables more efficient dictionary management through tracking pattern changes and evaluating their importance using provenance. Furthermore, it considers the relationships among sub-patterns using an FP-tree and performs pattern dictionary management that updates pattern scores based on time. Our experiments show that the proposed scheme outperforms existing graph compression methods in key performance metrics, such as compression rate and processing time.

Audio classification using deep learning models, essential for applications like voice assistants and music analysis, faces challenges when deployed on edge devices due to their limited computational resources and memory. Achieving a balance between performance, efficiency, and accuracy is a significant obstacle in optimizing these models for such constrained environments. In this investigation, we evaluate diverse deep learning architectures, including Convolutional Neural Networks (CNN) and Long Short-Term Memory (LSTM), for audio classification tasks on the ESC 50, UrbanSound8k, and Audio Set datasets. Our empirical findings indicate that Mel Spectrograms outperform raw audio data, attributing this enhancement to their synergistic alignment with advanced image classification algorithms and their congruence with human auditory perception. To address the constraints of model size, we apply model compression techniques, notably magnitude pruning, Taylor Pruning, and 8-bit quantization. The research demonstrates that a hybrid pruned model achieves a commendable accuracy rate of 89 percent, which, although marginally lower than the 92 percent accuracy of the uncompressed CNN, strikingly illustrates an equilibrium between efficiency and performance. Subsequently, we deploy the optimized model on Raspberry Pi 4 and NVIDIA Jetson Nano platforms for audio classification tasks. These findings highlight the significant potential of model compression strategies in enabling effective deep learning applications on resource-limited devices, with minimal compromise on accuracy.

The aim of the paper is to analyze the experimental results of the influence of elevated temperatures and strain rate on the mechanical and structural properties of steel 42CrMo4. The experiments were based on uniaxial tension and compression tests at high temperatures between 700 °C and 1000 °C and strain rates range 0.0018 - 0.1 s^-1. The influence of temperature and strain rate on yield stress, strain to fracture, hardness, structural changes, and fracture characteristics were analyzed. Due to the dynamic recrystallization phenomenon present during the hot tensile tests, an increase in the flow stress is observed at the beginning of the deformation, after which it decreases until the fracture. By increasing the deformation temperature from 700 °C to 1000 °C, the tensile stress decreases significantly for all strain rates. The increase in the strain rate leads to the increase in the tensile stress. In compression tests by increasing the strain rate, the true strain is slightly increasing, but this depends on the temperature. The non-uniformity of deformations obtained at different values of the strain rate and temperature were also analyzed. Analysis by scanning electron microscopy showed the ductile behavior of the material. The degree of damage of the material caused by the presence of cavities increases by increasing the deformation temperature. For all the presented deformation conditions, the presence of the fracture through the ductile fracture mechanism was produced by the localized of necking and the coalescence of microvoids. By increasing the deformation temperature and reducing the strain rate, the fracture behavior of 42CrMo4 steel can be improved.

The quasi-beta processing was considered as a promising processing technology to obtain a component with an excellent mechanical properties. To achieve an optimized quasi-beta processing parameter of TC21 alloy, the hot deformation behavior in near β phase region for the alloy with a forged structure was investigated by the thermal compression test and finite element (FEM) simulation. The obtained results indicated that the flow behavior of the samples was significantly influenced by the hot deformation parameters and it exhibited a flow hardening behavior at the start stage of deformation. Based on the experimental data, the constitutive equation and processing maps were obtained. The optimum hot processing parameters was 986℃/10^-3s^-1. Based on the FEM simulation results, the evolution of temperature field, strain field and stress field in the deformed samples at different strains exhibited a similar trend in the unstable region, which distributed symmetrically along the center line of the samples, and the center area of the samples was the highest and the center area of the section was the lowest.

Currently, the design of the concrete mix is an important part of the environmental problem. In front of this question, engineers face a major challenge that is addressed in two ways. On one hand, how do they use its component materials to improve its mechanical properties, on the other hand how do they use less polluting materials? Hence, in an environmental and economical view, laboratory tests were carried out on samples of concrete reinforced with smooth steel fiber extracted from the waste tires, in order to assess its impact and to prove its mechanical feasibility for these purposes. Consequently, laboratory results have shown satisfactory improvement in the behavior of concrete under compression loads in the elastic stage and an increase in ductility and toughness of the matrix in the plastic stage. Besides, taking into account the discontinuity and the structural disturbances observed during the loading of samples in the post-elastic state, a method has been proposed to calculate "the effective toughness and toughness Index of fiber concrete; on the other hand, this method has helped to better optimize length and slenderness of fibers for better use of this recycled material

Originating in the 1970s, Magnetic Compression Anastomosis (MCA) has lately been revisited with a focus on minimal invasive surgery (MIS). The aim of this report is to reappraise our earlier experience with MCA with the intention of facilitating future MCA advancement. A retrospective review was conducted regarding preclinical experiments and clinical trials at a single institution from 1980 through 1995. The reviewed information was compiled and appraised to generate proposals for future MCA use. The experimental studies, including 250 MCA cases in gastrointestinal and urinary tract animal models, demonstrated the technical versatility of MCA as well as the superior biomechanical characteristics in comparison to hand-sewn anastomoses. Clinical trials encompassed 87 MCA procedures in 86 children, 2 to 10 years of age, involving the following techniques: non-operative esophageal recanalization (n=15), non-operative ileostomy undiversion (n=46), Swenson pull-through (n=10), non-operative urethral recanalization (n=5), and extravesical ureterocystoneostomy (n=11). Clinical MCA was found to be successful in over 87% of cases. MCA limitations concerning anastomotic failure and scarring were thought to be mostly due to inadequate magnetic compression. Based on our historic experience, we propose further research on the technical aspects of MCA, along with the biologic aspects of anastomotic tissue remodeling. Magnets should be designed and manufactured for a wide spectrum of pediatric surgical indications, particularly in combination with novel MIS techniques.

Alloys based on TiNi are widely used in various fields of technology and medicine. In the present work, we report on preparation of TiNi-alloy based wire with the shape memory effect, which was used for compression clips for surgery. Composition and structure of the wire, and its martensitic and physical-chemical properties were studied using SEM, TEM, optic microscopy, profilometry, mechanical tests, etc. The TiNi alloy was found to consist of B2 and B19' and secondary-phase particles of Ti2Ni, TiNi3 and Ti3Ni4. Its matrix was slightly enriched in Ni (50.3 at. % of Ni). Homogeneous grain structure was revealed (an average grain size of 19±0.3 μm) with equal quantities of grain boundaries of special and general types. Surface oxide layer provide improved biocompatibility and promote adhesion of protein molecules. Overall, the obtained TiNi wire was concluded to exhibit martensitic, physical and mechanical properties suitable for its use as an implant material. The wire was then used for manufacturing compression clips with the shape memory effect and applied in surgery. The medical experiment that involved 46 children demonstrated that the use of such clips in children with double-barreled enterostomies permitted to improve the results of surgical treatment.

Individual plant cells are the building blocks for all plantae and artificially constructed plant biomaterials, like biocomposites. Secondary cell walls (SCWs) are a key component for mediating mechanical strength and stiffness in both living vascular plants and biocomposite materials. In this paper, we study the structure and biomechanics of cultured plant cells during the cellular developmental stages associated with SCW formation. We use a model culture system that induces transdifferentiation of Arabidopsis thaliana cells to xylem vessel elements, upon treatment with dexamethasone (DEX). We group the transdifferentiation process into three distinct stages, based on morphological observations of the cell walls. The first stage includes cells with only a primary cell wall (PCW), the second covers cells that have formed a SCW, and the third stage includes cells with a ruptured tonoplast and partially or fully degraded PCW. We adopt a multi-scale approach to study the mechanical properties of cells in these three stages. We perform large-scale indentations with a micro-compression system and nanoscale indentations through atomic force microscopy (AFM), in three different osmotic conditions. We introduce a spring-based model to deconvolve the competing stiffness contributions from turgor pressure, PCW, SCW and cytoplasm in the stiffness of differentiating cells. Prior to triggering differentiation, cells in hypotonic pressure conditions are significantly stiffer than cells in isotonic or hypertonic conditions, highlighting the dominant role of turgor pressure. Plasmolyzed cells with a SCW reach similar levels of stiffness as cells with maximum turgor pressure. The stiffness of the PCW in all of these conditions is lower than the stiffness of the fully-formed SCW. Our results provide the first experimental characterization of the mechanics of SCW formation at single cell level.

In this work, the recently proposed cracking elements method (CEM) is used for simulating the damaging processes of structures with initial imperfections. CEM is built in the framework of conventional FEM which is formally like a special type of finite element. The disconnected piecewise cracks are used for representing crack paths. Taking the advantages of CEM that both the initiations and propagations of cracks can be naturally captured, we numerically study the uni-axial compression tests of specimens with multiple joints and fissures, where the cracks may propagate from the tips, or from some other unexpected positions. Though uni-axial compression tests are considered, mainly tensile damage criteria are used in the numerical model. On one hand, the results demonstrate the robustness and effectiveness of the CEM while on the other hand, some drawbacks of the present model are demonstrated, showing the future work.

The QBIT theory is an attempt toward solving the problem of consciousness in the light of Quantum mechanics, Biology, Information theory, and Thermodynamics. “Internal representation” is a key concept in the QBIT theory of consciousness. An internal representation is defined as a pack of information (within a cognitive system) that represents an external stimulus.The QBIT theory suggests that when robustness of an internal representation exceeds a certain threshold, a conscious experience (or a quale) is generated. In this paper, the concept of internal representation and its relation with consciousness is explored.

Continuous rigid frame bridges across valleys are often at the risk of rockfalls caused by heavy rainfalls, earthquakes and debris flows in a mountainous country. Hollow thin-walled bridge piers (HTWBP) in valleys are exposed to the threat of the impact of accidental rockfalls. In the current research, ANSYS/LS-DYNA is used to establish a high-precision rockfall-HTWBP model. The rockfall-HTWBP model is verified against a scaled impact test of a previous research. A mesh independence test is also performed to obtained an appropriate mesh size. Based on the rockfall-HTWBP model, the impact force, damage and dynamic response characteristics of HTWBP under the rockfall impact are studied. In addition, a damage assessment criteria is proposed based on the response surface model combined with Central Composite Design method and Box-Behnken Design method. The main conclusions are as follows: 1）The impact force of rockfall has a substantial impulse characteristic, and the duration of the impulse load is approximately 0.01s. 2）The impacted surface of the pier is dominated by the final elliptic damage with the conical and strip damage areas as the symmetry axis. The cross-sectional damage mode is compression failure in the impact area and shear failure at the corner. 3）The maximum displacement occurs in the middle height of the pier. The maximum displacement increases with impact height, impact velocity and rockfall diameter and decreases with the uniaxial compressive strength of the concrete. 4) The initial impact velocity and diameter of the rockfall are the most significant parameters affecting the damage indices. In addition, a damage assessment method with a damage zoning diagram based on the response surface method is established for the fast assessment of the damage level of impacted HTWBP.

Recently, more and more countries are entering the global race for university competitiveness. On the one hand, global rankings are a convenient tool for quantitative analysis. On the other hand, their indicators are often difficult to quickly calculate, they often contradict each other. We thought about using widely available indicators for a quick analysis of the University's publication strategy. We opted for the normalized citation indicators available in SciVal analytical tool, i.e. Source Normalized Impact per Paper (SNIP) and Field-Weighted Citation Impact (FWCI). We have demonstrated the possibility of applying the correlation analysis to the impact indicators of a document and a journal on the sample of the social and humanitarian fields at Peoples' Friendship University of Russia. Particular attention was paid to the application of the results in practice.

In cardiac surgery, post-sternotomy pain is a significant issue, peaking within 48 hours and requiring proper analgesia for both acute relief and to avoid chronicization. Opioids are commonly used for pain management post-surgery but pose risks like adverse effects and dependency. Post-cardiac surgery pain can stem from various sources - somatic, visceral, and neuropathic, making opioid reliance a concern. Multimodal analgesia, combining different medications and regional anesthesia techniques, is increasingly recommended to decrease opioid use and its related problems. Strategies include acetaminophen, gabapentinoids, NMDA antagonists, alpha-2 agonists, intravenous lidocaine, anti-inflammatory drugs, and regional anesthesia. Implementing these approaches can enhance pain control, lessen opioid reliance, and improve cardiac surgery outcomes. The ERAS® Cardiac Society strongly advocates for an opioid-sparing multimodal approach to benefit patient recovery by reducing complications and enhancing satisfaction. This review aims to consolidate current evidence to assist healthcare providers in customizing pain management for patients post-cardiac surgery, emphasizing reduced opioid use and optimizing the recovery process.

Patients with chronic (CM) and high frequency episodic migraine (HFEM) report cognitive complaints that contribute to migraine burden. Although, there is little evidence about the ef-fects of migraine treatments on these symptoms. Objective: To evaluate the effect of preventive treatment on the impact of cognitive symptoms, specifically the ability to concentrate, in individuals with CM and HFEM. Methods: Prospective cohort study in patients with CM and HFEM initiating treatment with botulinum toxin (BT) or anti-CGRP/R monoclonal antibodies (mAbs). Patients were evaluated at baseline and after 3 months of treatment, using a headache diary and a question about the im-pact of migraine attacks on concentration (never, rarely, sometimes, often, and always). Results: 108 patients (105 females, 44.3 years of age on average), 75% with CM and 27% with HFEM were included, 55 received a first session of BT and 53 received 3 injections of a monthly mAb. In both groups, there was a significant decline on the impact of migraine in concentration (related samples Wilcoxon signed rank test <0.001) compared to baseline. Reduction in monthly headache days was the main predictor of any concentration improvement, while treatment group, age, ongoing medication with topiramate or baseline medication overuse were not sig-nificant. Conclusion: Preventive treatment of HFEM or CM with drugs not acting on central nervous sys-tem is associated with a decrease of the impact of migraine attacks on concentration, predicted by the decline in headache days. These results indicate that migraine preventive treatment also improves non-pain symptoms, which is relevant given the contribution of cognitive complaints to the impact of headache attacks

Globally 703 000 people commit suicide (4th leading cause of mortality among 15-29 year-olds, 1.4% of all deaths globally) every year, which have a negative effect on families, colleagues, and societies. India accounts for 36.6 percent of global suicide in women and 24.3 percent among men, while having only 17.8 percent of the global population, also remarkable fact is that the suicide ratio for female is 14.7 per 100,000 compared to 21.2 per 100,000 of male which is 2.1 times the global average in female, while 1.4 times higher for men. COVID-19 (coronavirus disease-2019) pandemic has certainly affected the physical, mental, economical and social well being of global population directly or indirectly in different ways. Deteriorating physical, mental, economical and social health of an individual could increase the suicidal tendency, leading to accidents and suicide. This study tried to find out the COVID-19 pandemic situation impact on accidental death as well as suicide rates in India. The study period is from 1st January 1967 to 31st December 2021, to assess the effect of the COVID-19 pandemic situation on suicide and accidental death rates. This study revealed that the suicide deaths percentage among males increased significantly in comparison to females in COVID-19 era and actual count and incidence also increased. This study revealed that the mean accidental death and suicide both increased during COVID period of study as compared to pre-pandemic whole period from 1967 by 25.47 % and 30.61% respectively. Alternatively we can say that the accidental death and suicides increased significantly in India, which is largely preventable.

The thermal insulation properties of building walls are critical to the overall energy efficiency and comfort of a building. One important factor that can affect these properties is the type of bricks used in construction. Bricks can vary in their geometry and thermal coefficient, which can impact their ability to transfer heat through the wall. The geometry of a brick can affect its thermal properties by altering the amount of air trapped within it and the surface area available for heat transfer. Hollow bricks or those with complex geometries may have lower thermal conductivity than regular solid bricks due to the air pockets trapped within them. Conversely, larger surface areas on the exterior of the brick can increase heat transfer. The thermal coefficient of clay, a common material used in brick production, is another important factor. Clay has a relatively low thermal conductivity, meaning it is a poor conductor of heat. However, the quality of the clay, as well as the firing temperature and duration used in brick production, can impact its thermal coefficient. Higher firing temperatures and longer firing times can result in a more compact and dense clay brick, which can improve its thermal properties. In summary, the thermal insulation properties of building walls can be significantly affected by the type of bricks used in their construction. It is important to consider the geometry and thermal coefficient of the bricks when designing a building to achieve the desired level of thermal insulation. By selecting bricks with appropriate properties, designers can help to improve the energy efficiency and comfort of the building while reducing its environmental impact.

This study aims to examine households' perceptions of the socio-cultural, economic, and environmental impacts of ecotourism in the protected area, focusing on Simien Mountain National Park, North west Ethiopia. Using a mixed research approach with a sequential explanatory design, we collected data through a single-round cross-sectional survey, interviews, focus groups, discussions, and secondary sources of information. Three districts were selected using a multi-stage sampling method, and 397 respondents were surveyed. We analyzed the quantitative data using percentages, averages, t-tests, ANOVA, and regression models, and examined the qualitative data using thematic analysis. Our findings suggest that households living in the park generally perceived the social, economic, and environmental impacts of ecotourism as favorable. However, the study also revealed that the benefits of tourism are not being fully utilized, indicating the potential for further development. We found significant differences in how people perceived ecotourism based on their gender, education, and residence location. Specifically, men and respondents with higher levels of education were more likely to perceive ecotourism positively. The logistic regression model revealed a statistically significant direct cause-and-effect relationship between three demographic factors of household respondents' participation in ecotourism (dependent variable) and gender (B = 1.85, p = 0.023), educational attainment (B = 0.23, p = 0.003), and location (B = 0.42, p = 0.041). In light of these findings, the authors recommend that the local government and the Ethiopian Wildlife Conservation Agency should develop sustainable plans for tourism that will benefit nearby communities and improve living conditions in the park.

Severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2), also known globally as COVID-19, originated in December 2019 in Wuhan, Hubei province in China and has rapidly spread across the globe ever since. The first recorded case in sub-Saharan Africa was in Nigeria, on the 25th February, 2020. The virus continues to spread, and new variants of the disease have emerged, the number of deaths and new infections in the countries of sub-Saharan Africa has been relatively low compared to predictive models. This could be due to several factors, such as slower transmission dynamics of the virus, a lower-case fatality rate, or a lack of testing or reliable data. Whilst this may also, in part, be due to the robustness of the nations' public health responses, there is scarce reporting on the specifics of this. However, emerging research has demonstrated that various environmental factors could influence virus transmission. The study adopted collected meteorological data that was critically analysed and discussed. The impact of three factors in the context of sub-Saharan African nations: temperature, ultraviolet (UV) exposure and pre-existing infection with Plasmodium (malaria) were discussed. These factors were discussed critically in light of the reduced rates of transmission and mortality observed.

Tourism may not sustainably support territories with limited natural resource stock as islands. The volume in visitor arrivals and the industry investments can increase the pressure even beyond sustainable levels. There is an evident and unresolved tension between these two great polarities, sustainability and economic growth driven by tourism. The aim for policymakers is to find an acceptable equilibrium between these two dimensions. This paper investigates the tourism evolution between 2007 and 2019 in 15 Mediterranean islands, comparing the tourism pressures through statistical indicators. The analysis will compare tourism demand and supply trends in these contexts. The performances will be evaluated to identify the Islands positioning between sustainability needs and tourism development opportunities considering post-covid-19 challenges.

Abstract Mastitis is a common disease of dairy animals. The source of mastitis infection may be regarded as contagious or environmental. A wide range of pathogens including bacteria, viruses, fungi, and the toxins of these pathogens can cause the disease. Mastitis is generally associated with poor hygienic and husbandry practices. The primary reservoir of infection is the mammary gland. The infectious agent enters through the milk canal, interacts with the mammary tissue/cells and multiplies. Most contagious mastitis causing pathogens are spread during milking. Most other species are opportunistic invaders from the cow's environment.

The COVID-19 has caused gigantic negative effects on populace wellbeing, society, education, and the economy in Bangladesh. The aim is to deliver a comprehensive overview of the observed and the possible impacts that could appear in the coming days. The study is based on secondary information. During the early period, due to a lack of accurate facts about the case affected and death tension up-and-down among the nations. The total number of confirmed cases is increasing following geometric patterns in Bangladesh. Dairy farmers, vegetable producers, pharmaceuticals, poultry farmers are in deep crisis due to lower prices. Also, the pandemic has seriously affected educational systems, banking, FDI, ready-made garments, remittances, etc Finally, it is not possible to mitigate the effects of pandemic individually but the integrated effort from the state authority as well as concern people of all sectors need to come forward.

Aflatoxins are a known cause of primary liver cancer in Mozambique since pre-independence epidemiological studies. However, their impact goes beyond the public health, affecting the country’s economy and raising legal concerns. As a developing country endemic for Aspergillus, the nation has been struggling to keep pace with external trade quality demands, delicate policy making, still dealing with the farmers’ limitations to control the contamination. The contamination shows variations over time, space and the different commodities. Considering the recommendations of the Codex Alimentarius, the major crops will be highly implicated unless there is major intervention from the authorities to control the toxins.

This article describes the POTENTIALS project, which aimed to develop business models for the reuse of former industrial and mining sites in different regions. The project focused on the creation of eco-industrial parks as a result to enable sustainable energy production and reduce waste and pollution. A key aspect was the Territorial Impact Assessment (TIA), a new and complex policy assessment tool. Therefore, the TEQUILA (Territorial Efficiency Quality and Identity Layer Assessment) approach is used to describe the TIA and emphasizes its application in assessing the impact of EU policies and projects on territorial cohesion. It underlines the need for a differentiated understanding of the regional characteristics and potential impacts of policies; and stresses the importance of regionalized impact models for the assessment. Furthermore, the process and results of applying the TEQUILA methodology to assess the territorial impact of different scenarios of business models within the POTENTIALS project is given.