Considering nutritional qualities of gofio (Gf) and aloe vera juice (AVJ), their combination is indicated as an easy and fast source of ingest of basic bio elements. As the texture of the final product must be accepted by customers, the influence of Gf concentration on the rheological behavior of Gf/AVJ suspensions was determined. Shear thinning index of AVJ maintains unaltered despite the presence of Gf particles, although the viscosity value increases as expected. Linear viscoelastic studies on Gf/AVJ confirmed this is a viscoelastic liquid that changes from chewy to creamy texture with Gf concentration increase.

In the last two decades, gelatin-based hydrogels have been widely used as tissue engineering scaffolds due to their excellent biocompatibility, biodegradability, easy processability, transparency, non-toxicity, and reasonable structural similarity to the natural extracellular matrix (ECM). However, intrinsic low mechanical properties of gelatin are not structurally and mechanically suitable to support cell growth and proliferation. That’s why various crosslinking strategies including physical, chemical, enzymatic and combination of them as well as networking patterns including double network, interpenetrating network and nano reinforcing mechanism have been utilized to enhance the structural stability and mechanical integrity of gelatin. In this review, the advances in modulating the mechanical properties of gelatin-based hydrogels for the design and development of structurally stable scaffolds for tissue engineering are discussed. The optimized crosslinking parameters with the adequate mechanical properties of gelatin-based hydrogels are reviewed. Gelatin-based scaffolds for a wide range of tissue engineering applications, such as bone, cartilage, cardiac, skin, and nerve tissue engineering are also outlined. Lastly, current challenges and future perspectives in this research field are presented.

The topic of modification of magnesium oxychloride cement (MOC) via specific functional additives is very much pronounced in the research of alternative building materials. This study deals with the co-doping of MOC by 1D and 2D carbon nanomaterials in order to improve its mechanical properties while using tannic acid (TA) as a surfactant. Furthermore, the effect of TA on MOC also covers the improvement of water resistance. As a filler, three size fractions of standard quartz sand are used. The proposed types of MOC-based composites show promising results considering their mechanical, macro- and microstructural, chemical, and hygric properties. The use of 1D and 2D nanoadditives and their mixture enables the improvement of the flexural strength and most of all softening coefficient, the durability parameter characterizing the resistance of the prepared materials to water. For samples immersed in water for 24 h, the compressive strength of all modified composites tested was higher than that of the reference composite. Quantitatively, the developed co-doped composite shows mechanical parameters comparable to or even better than those of commonly used Portland cement-based materials, while maintaining high environmental efficiency. This indicates its potential use as an environmentally friendly alternative to Portland cement-based products.

In order to further reduce the emissivity of the hydrophobic low infrared emissivity composite coating and improve the mechanical properties of the coating, the dispersant, adhesion enhancer, and defoamer were used to improve the dispersion state of the fillers, the interface structure, and the surface state of the hydrogen silicone oil modified polyurethane/Al composite coating. The effects of dispersant, adhesion enhancer, and defoamer on the micro-structure, emissivity, glossiness, hydrophobic property, and mechanical properties of the coating were systematically studied. The results show that the polycarboxylate anionic dispersant can obviously improve the dispersion state of flake Al powder and nano-SiO2 in the coating, so that the infrared emissivity of the coating can be reduced, and the coating can have higher hydrophobic and mechanical properties. The bonding strength between the resin matrix and the metal substrate of the coating can be significantly improved by the adhesion enhancer through the bridging action, so that the adhesion strength and impact strength of the coating can be significantly improved. The defoamer can significantly reduce the pores in the coating, so that the surface state of the coating can be significantly improved, and the mechanical properties of the coating can be significantly improved. The coating has the best emissivity (0.527), glossiness (4.3), adhesion strength (grade 1), impact strength (40 kg.cm), and hydrophobic property (water contact angle (WCA) is 140o) when the amount of dispersant, adhesion enhancer, and defoamer is 5 wt%, 4 wt%, and 1 wt%, respectively.

The hot rolling in the process chain of the aluminium rolled products present the critical element of material quality and influence on productivity. The desire to increase the letter demand modifications of hot rolling, consequential changes of microstructure, crystallographic texture, mechanical and formability properties must be knowledge and consistently considered in planning the rolling process and rolled product. Achieving lower thicknesses of the hot-rolled band would enable fewer passes with cold rolling; consequently, hot rolling with the same number of passes will complete with lower temperatures. Microstructural and texture characterization with the optical microscope and scanning electron microscope for the hot-rolled band 3.25 mm the smaller grains appeared in the center of the cross-section, unlike for the hot-rolled band 6 mm, the smaller grains were detected on the upper and bottom position of the cross-section. Furthermore, the comparison shows also that the hot-rolled band 6 mm has 64 % of random texture components and 83 % of recrystallized grains, and the proportional adjustment for the hot-rolled band 3.25 mm has the 42 % of random texture components and 55 % of recrystallized grains. For the mechanical testing results, the elongation values in rolling and transverse directions significantly differ just in the case of a hot rolled band of 3.25 mm. Consequently, the earing results are more than 1.5 % higher for the hot-rolled band, 3.25 mm, than the hot-rolled band, 6 mm.

The evolution of transportation has been inextricably tied to the progress of civilization. Through innovation, the automobile business has been working to improve safety, quality, and compliance with environmental regulations. Electric vehicles have made significant strides in this area, but optimizing their efficiency requires a special focus because they expend energy that can be recovered in a variety of ways. Energy harvesting, a cutting-edge technology that captures wasted energy from vehicles, has recently received a lot of attention as it constitutes a means to improve the efficiency of electric vehicles. Dissipated energy can be converted into electricity using regenerative energy recovery systems and put to various uses. This study tenders a thorough examination into energy recovery technologies which could be applied to the various types of energy dissipated in electric vehicles. Firstly, the paper investigates the possible sources of energy recoverable from an electric vehicle, as well as the various types of energy dissipated. Secondly, the article examines the energy recovery technologies most frequently used in vehicles, categorizing them according to the type of energy and application. Finally, it determines that with further research and development, energy harvesting holds considerable potential for improving the energy efficiency of electric vehicles. New and innovative methods for capturing and utilizing wasted energy in electric vehicles can be established. The potential benefits of applying energy recovery systems in electric vehicles is a vital issue for the automobile industry to focus on due to the potential benefits involved. The ongoing progress currently being made in this field is expected to play a significant role in shaping the future of transportation.

In this investigation, Cu-Ni alloys for possible fixed dental prostheses (FDPs), with different aluminum additions were produced using vacuum atmosphere. Annealed alloys (He atmosphere) with low aluminum concentration showed a coarse dendritic structure, while samples with high aluminum concentration showed a refined dendritic structure. Structural defects analyses have shown a relative low vacancy concentrations. Hardness value increases approximately five times for the alloyed samples compared with the as-cast and unalloyed samples. Compression test results have shown a noticeable strengthening improvement, mainly in samples heat treated with 10 at % Al, while samples with 5 at % Al presented also acceptable resistance. Results are discussed in terms of dislocation mobility and hardening precipitation mechanism.

Bobbin Tool Friction Stir Welding (BTFSW) is a variant of FSW process using the special two shoulder tool that forms the top and bottom weld surface. As such, a significant simplification of welding setup is achieved. One of the dominant parameters of BTFSW process is the interference between tool shoulder pinch gap and weld metal thickness. In this research, the influence of interference of the square pin tool with convex shoulders on process temperature, microstructure, tensile, impact and bend performance were studied, and appropriate correlations were devised. The base metal was aluminum-magnesium alloy, with the interference varied in the range of 0.1 to 0.5 mm. The worm defects and irregularities were found in all specimens except in specimen welded with 0.4 mm interference. Optimal interference of 0.4 mm resulted in the highest mechanical properties, which, in terms of tensile strength and reduction of area were similar to the base metal. Furthermore, impact strength was significantly higher, which was attributed to grain refinement effect in the nugget zone.

Fe rich soft magnetic alloys are candidates for applications as magnetic sensors and actuators. These alloys can also be added to hard magnetic compounds to obtain spring magnets. In this work we produce two nanocrystalline Fe-Zr-B-Cu alloys by the powder metallurgy powder technology of mechanical alloying. The increase of the boron content favors the reduction of the crystalline size. Thermal analysis (by differential scanning calorimetry) shows at temperatures between 450 and 650 K wide exothermic processes, associated with the relaxation of tensions of the alloys produced by milling. At high temperatures, a main crystallization peak is found. The apparent activation of this process was determined by Kissinger and isoconversional methods. The values are compared with those found in the scientific literature. Likewise, adapted thermogravimetry permits to determine the Curie temperature. The functional response has been analyzed by hysteresis loop cycles. According to the composition, the decrease of the Fe/B ratio diminishes the magnetic soft behavior.

The purpose of this study was to determine changes in the mechanical properties of the thigh and lower leg musculature during the early follicular and ovulatory phases. Subjects were 15 female university students with normal menstrual cycles. The early follicular and ovulatory phases were estimated by the basal body temperature method, ovulation kits, and salivary estradiol concentration measurement. The MyotonPRO digital palpation device (Myoton AS, Tallinn, Estonia) was used to measure muscle and tendon stiffness in the early follicular and ovulatory phases. Measurement sites were the rectus femoris (RF), vastus medialis (VM), patellar tendon (PT), medial head of gastrocnemius, soleus, and Achilles tendon. No significant differences in stiffness of all muscle tendons were identified between the early follicular and ovulatory phases. In the ovulatory phase, a significant positive correlation was seen between stiffness of RF and PT, and between stiffness of VM and PT. These results suggest that the stiffness of muscles and tendons of anterior sites of the thigh and posterior sites of the lower leg may not change between the early follicular and ovulatory phases. During the ovulatory phase, tendons may also be stiffer in individuals with stiffer anterior thigh muscles.

The preparation of new materials based on starch for the development of biodegradable packaging is increasing, however, the poor properties of this biopolymer for this application causes an area of opportunities for the improvement of water vapour permeability (WVP), mechanical properties, thermal properties, hydrophilicity, water absorption, among others. Hence, starch has been combined with other polymers such as polyvinyl alcohol, which has shown an improvement in the mechanical properties of starch, also, the use of clays suggests that the properties of response to water can be improved. Therefore, in this work, the preparation and characterization of starch-PVA-nanoclay films prepared by solvent casting is reported. The results obtained suggest that the sonication of nanoclay is necessary to reach a good dispersion, which promotes a strong interaction among starch-PVA-nanoclay. In addition, the properties of WVP and mechanical properties of films improved with incorporation of nanoclay, the concentration of 0.5% w/v of nanoclay showed to be the best concentration due to concentrations of 1.0 and 1.5% w/v were poorer than 0.5% w/v. Accordingly, the successful incorporation of nanoclays into the matrix starch-PVA suggests that this material is a good candidate for use as packaging.

Objective: This study aims to identify the impact of nutritional factors on mechanical ventilation duration for critical patients. Patients and Methods: The current study was a single-center, prospective observational design which enrolled one-hundred critically ill patients who were admitted to an intensive care unit (ICU). It demonstrates purposive sampling and also performs the descriptive nutritional factors influencing the mechanical ventilation duration. Daily calories target requirement scale (DCRS), subjective global assessment form (SGA), dyspnea assessment form, and APACHE II have been used as methods in the study along with time to initial enteral nutrition (EN) after 24-hour admission and daily calories target requirement over 7 days to assess patients. Data is analyzed using the multiple regressions. Results: As a result, nutritional status monitoring, time to initial EN, calories and target requirements are statistically positive significance associated with the mechanical ventilation duration respectively (R = 0.54, R = 0.30, R= 0.40, p < 0.05). However, age, illness severity, and dyspnea scales are not associated with the mechanical ventilation duration (p> 0.05). Therefore, the nutritional status, malnutrition scores and calorie target requirements can be used to significantly predict the mechanical ventilation duration. The predictive power is 58 and 28.0% of variance. The most proper influencer to predict the mechanical ventilation duration is nutritional status or malnutrition scores. Conclusion: The research findings show that the nutritional status, time to initial EN, and calorie target requirement within 7 days of admission are associated with the mechanical ventilation duration in the critical patients. Therefore, it can be used to develop guidelines reducing the mechanical ventilation duration and to promote the ventilator halting for critical patients.

The distributed long-range sensing system using the standard telecommunication single-mode optical fiber in a function of a distributed sensor for sensing of mechanical vibrations is described. Various events generating vibrations such as walking or running person, moving cars, trains and others can be detected, localized and classified. The sensor and related sensing system components were designed and constructed and the system was tested both in the laboratory and in the real situation with 88 km telecom optical link, and the results are presented.

Polymethyl methacrylate (PMMA) is a transparent thermoplastic with excellent optical properties, transparent surface, low moisture absorption, tensile and electrical resistance. In this study, the alloy was prepared through PMMA and cycloolefin copolymer (COC) due to some similar properties. The mechanical test showed that properties such as impact resistance, elongation, tensile, and flexural strength decreased by adding COC by up to 20% due to less incompatibility and miscibility, but mentioned properties improved by adding COC 40% due to sub-phase generation. The DSC and DMTA tests showed improvement in the thermal properties of alloys by adding 40% COC. SEM micrographs exhibited a softer surface and more phase elongation of the alloy. Finally, the sample was selected as the optimal sample in terms of mechanical properties irradiated by electron beam, and amplification results showed that a dose of 50 KGY increased the mechanical and thermal properties relatively.

Metal 3D printing technology is a promising manufacturing method, especially in the case of complex shapes. The quality of the printed product is still a challenging issue for mechanical applications. The anisotropy of the microstructure, imperfections, and residual stress are some of the issues that diminish the mechanical properties of the printed sample. The simulation could be used to investigate some technical details, and this research has tried to computationally study the metal 3D printing of austenitic stainless steel to address austenite microstructure and local yield strength. Two computational codes were developed in Visual basics 2015 to simulate the local heating/cooling curve and subsequent austenite microstructure. A stochastic computational code was developed to simulate austenite grain morphology based on calculated thermal history. Then Hall-Pitch equation was used to estimate the yield strength of the printed sample. These codes were used to simulate the effect of temperature of the printer’s chamber on microstructure and subsequent yield strength. The austenite grain topology is more columnar at a lower temperature. The percentage of the equiaxed zone will be increased at a higher chamber’s temperature. Almost a fully equiaxed austenite microstructure will be achieved at 800 C chamber’s temperature, but the last printed layer, which is columnar and can be removed by cutting then. The estimated local austenite grain size and the local yield strength in the equiaxed regions are in the range of 15 to 30 μm and 270 to 330 MPa at 800 C temperature of printer’s chamber, respectively.

With the emergence of COVID-19 we are confronted with a new clinical picture of acute respiratory distress syndrome in the intensive care unit. In the majority of patients, the respiratory mechanics are very different from the “normal” ARDS patient. We measured transpulmonary pressure and dead space ventilation to assess the effects of high and low PEEP levels on lung compliance and ventilation-perfusion mismatching. Advanced respiratory mechanics were assessed in 14 patients. Compared to ARDS patients, lung compliance was relatively high (61 ± 5 mL/cmH₂O). COVID-19 patients had high dead space ventilation and gas exchange impairment (Bohr 52 ± 3%; Enghoff modification 67 ± 2%; ventilatory ratio 2.24 ± 0.23). we show that higher PEEP levels decrease lung compliance and in most cases increase dead space ventilation, indicating that high PEEP levels probably cause hyperinflation in patients with COVID-19. We suggest using prone position for an extended period of time, and apply lower PEEP levels as much as possible.

The Wolfram (W), Silicium (Si) and Molybdenum (Mo) doped Co-Cr biomedical alloy were fabricated by additive manufacturing method, which is part of powder metadology. The mixture of Wolfram (W), Silicium (Si), Chrome (Cr) and Cobalt (Co) alloy is known good wear and corrosion resistance among of biomedical applications. By addition of Molybdenum (Mo) into the structure of alloy, the structure become more stbale also increase the corrosion and wear resistance. In addition, the effects of secondary annealing process on the alloy were investigated. The microstructure of the produced alloy was analyzed by X-ray diffraction method XRD, Energy Dispersive X-Ray Analysis EDX and scanning electron microscope SEM. Moreover, Electrochemical corrosion test, micro hardness and density measurements were performed to investigate the mechanical properties of the alloy. As a result of the analyzes, the effects of Molydenum (Mo) doped and secondary annealing on the microstructure and mechanical properties of bioalloying were determined.

The aim of this work was to prepare bioplastics from renewable and biodegradable molecules. In particular, the bioplastics were produced by using as biopolymer source the grass pea (Lathyrus sativus L.) flour, the proteins of which were structurally modified by means of microbial transglutaminase, an enzyme able to catalyze isopeptide bonds between glutamines and lysines. We analyzed, by means of Zeta-potential, the flour suspension with the aim to choose which pH is more stable for the production of film-forming solutions. The bioplastics were produced by casting and they were characterized according to several technological properties. Optical analysis demonstrated that films cast in the presence of the microbial enzyme are more transparent compared to the untreated ones. Moreover, the visualization by Scanning Electron Microscopy demonstrated that the enzyme-modified films possessed a more compact and homogeneous structure. Furthermore, the presence of microbial transglutaminase allowed to obtain film more mechanically resistant. Finally, digestion experiments under physiological conditions performed in order to obtain information useful for applying these novel biomaterials as carriers in the industrial field, indicated that the enzyme-treated coatings might allow the delivery of bioactive molecules in the gastro-intestinal tract.

For development and successful application of any material, a clear understanding of their mechanical behavior is one of the most important things, but when it comes to nanofibers networks it become a challenge due to, their high porosity, many scales in their structure, and characteristics non-linear. Therefore, an experimental methodology in conjunction with a theoretical model that can fully consider their characteristics is still needed. In this work we proposed a model that incorporates the propagation of the elastic waves in two-phase media to determine the effective elastic modulus of electrospun membranes of PLA/gelatin given the mechanical properties of nanofibers, shape, distribution and concentration. The model was verified via laser ultrasonic testing. It was found that the values predicted for the effective modulus by the model were higher than the values obtained from experimental results. One explanation is due to the experimental density. As a result, the P-Wave velocity from the model best fit to experimental results and it has the same behavior, decrees as the concentration of gelatin in the solution. These results indicate the model and experimental methodology can assist in the dressing of nanofibers networks and electrospun materials.

The developed microstructure features a long with mechanical properties in vacuum brazing of commercially pure Ti-alloy using Ti₂₀Zr₂₀Cu_60-x-Ni_x (x=10, 20, 30, 40 and 50) metallic filler. Brazing temperatures and holding times employed in this study were 1240-1279 K (967-1006^oC) for a period of 10 min, respectively. The mechanical properties of brazed joints were evaluated by nanoindention at a constant peak load of 5000 μN and tensile tests. The number of intermetallic phase, such as NiTi₂, Ti₂Cu, (Ti, Zr)₂Cu, (Ti, Zr)₂Ni, β(Ti, Zr), α-Ti and NiTi. The solid solution matrix have been identified at 1279 K out of these different regions the NiTi₂ rich region had the highest nanohardness of 17 GPa, It is interesting to note that among five different glasses, the Ti₂₀Zr₂₀Cu₁₀Ni₅₀ has the highest yield strength of 17 GPa, which is mainly due to NiTi₂ phase. Based on the tensile test results all cracks propagate along the brittle intermetallic compounds like NiTi₂ in the reaction layer the reduction of the strength of the joints and fracture behaviour upon propagation of the crack, which shows the morphological cleavage including facets characteristics.

Cu₆Sn₅ whiskers precipitated in Sn3.0Ag0.5Cu/Cu interconnection in concentrator silicon solar cells solder layer were found and investigated after reflow soldering and during aging. Ag₃Sn fibers can be observed around Cu₆Sn₅ whiskers in the matrix microstructure, which can play an active effect on the reliability of interconnection. Different morphologies of Cu₆Sn₅ whiskers can be observed, and hexagonal rod structure is the main morphology of Cu₆Sn₅ whiskers. A hollow structure can be observed in hexagonal Cu₆Sn₅ whiskers, and a screw dislocation mechanism was used to represent the Cu₆Sn₅ growth. Based on mechanical property testing and finite element simulation, Cu₆Sn₅ whiskers were regarded as having a negative effect on the durability of Sn3.0Ag0.5Cu/Cu interconnection in concentrator silicon solar cells solder layer.

In this study, 10%PTFE/PEEK blend were modified by potassium titanate whisker (PTW) and chopped glass fiber (GF), respectively. The blends were prepared by three-screw extruder. Through the investigation of thermal stability, tribological properties, mechanical properties and rheological behavior, the effects of reinforcing agents were determined. The results illustrated that the mechanical properties of 10%PTFE/PEEK blend can be dramatically improved by adding reinforcing agent of PTW or GF, and the reinforcing effect of GF was especially obvious. As for tribological properties, 1% addition was the best proportion. The friction coefficient and wear rate of the blend with 1% PTW were 0.283 and 4.97 × 10^-6 mm³/N · m, which decreased by 7.2% and 21% compared with those of the blend without reinforcing agent.

In this work, we designed a MEMS device which allows simultaneous direct measurement of mechanical properties during deformation under external stress and characterization of the evolution of microstructure of nanomaterials within a transmission electron microscope. This MEMS device makes it easy to establish the correlation between microstructure and mechanical properties of nanomaterials. The device uses piezoresistive sensors to qualitatively measure the force and displacement of nanomaterials, e.g., in wire and thin plate forms. The device has a theoretical displacement resolution of 0.19 nm and a force resolution of 2.1 μN. The device has a theoretical displacement range limit of 2.74 μm and a load range limit of 27.75 mN.

The thermal degradation behaviour of 10:90 and 90:10 blends of Polyethylene Terephthalate (PET) and petroleum coke has been investigated using mechanical alloying (milling) at 300 rpm and for periods up to 1-10 hours. Milled specimens were characterised using SEM and x-ray diffraction; their thermal degradation behaviour was investigated using thermo-gravimetric analyser (TGA) for temperatures up to 1200°C. Whereas PET specimens showed a tendency towards flattening out and increased surface area during collisions in ball mills, petroleum coke particles tended to break down into smaller particles. 10:90 and 90:10 blends of PET and coke showed significant microstructural evolution with increasing speeds and time including fracture, strain hardening and re-welding. X-ray diffraction results showed clear evidence for increasing amorphous component in petroleum coke without much influence on PET crystallinity. Thermo-gravimetric results showed a significant increase in the overall degradation and much higher weight losses associated with mechanical alloying. This study has shown that mechanical alloying could be used to modify the degradation behaviour of coke/plastic blends and corresponding yield during pyrolysis with implications for plastic waste management.

Global demand for blueberries has surged in recent years, primarily due to their health benefits. However, blueberries postharvest losses, particularly firmness loss and decay, remain significant challenges. This study applied high concentrations of CO2 (15% and 20%) for 3 days at 1 °C to highbush (Duke) and rabbiteye (Ochlockonee) blueberries to assess their effects on maintaining quality, especially firmness, during low-temperature storage. Various quality parameters were evaluated, including titratable acidity, pH, total soluble solids, weight loss, and decay. The impact of gaseous treatments on firmness was analysed through mechanical parameters and the expression of genes related to cell wall integrity (XTH23, PL8, PG, PM3, EXP4, and VcGH5). The effectiveness of the treatments varied between species. High CO2 levels successfully reduced decay in both cultivars, but only the highbush variety (Duke) showed improvements in firmness. In Duke, CO2 treatments influenced the expression of genes associated to cell wall integrity, such as XTH23, PL8, and GH5. In contrast, the roles of PG and PME in firmness maintenance were minimal, showing no significant differences between treatments. While CO2 did not enhance firmness in Ochlockonee, it effectively reduced weight loss, highlighting the need for tailored postharvest strategies for different blueberry cultivars.

Expanded Polystyrene (EPS) beads lightweight soil is a new type of artificial geotechnical material with low density and high strength, to promote the wide application of EPS beads lightweight soil in the project, replacing some cement with fly ash as a curing agent, which can consume the waste fly ash and reduce the cost of the project. EPS beads were used as a lightweight material, and cement and fly ash were used as curing agents into the raw soil to make fly ash EPS lightweight soil. The EPS beads contents are 0.5%, 1%, 1.5%, and 2%, the total curing agent contents are 10%, 15%, 20%, and 25%, and the proportions of cement replaced by fly ash are 0%, 15%, 30%, 45%, and 60%, respectively. Unconfined compressive strength (UCS) test and scanning electron microscopy (SEM) test were conducted. The results show that the EPS content, the total curing agent content, and the proportion of cement replaced by fly ash have a significant impact on the UCS of lightweight soil. It decreases with an increase in the EPS content, increases with an increase in the total curing agent content, and decreases with an increase in the proportion of cement replaced by fly ash. When the proportion of cement replaced by fly ash is not too high, the strength of lightweight soil decreases less, and its performance can still meet the engineering needs. At the same time, it can also consume fly ash and reduce environmental pollution. EPS lightweight soil mixed with fly ash still has advantages, and it is recommended that the proportion of cement replaced by fly ash is controlled to less than 30%. The failure patterns of lightweight soil mainly include splitting failure, oblique shear failure and bulging failure, which are related to the material mix ratio.

Aluminum-based hybrid nanocomposites, particularly Al6061 alloy, have gained prominence in the scientific community due to their unique properties, such as high strength, low density, and good corrosion resistance. The production of these nanocomposites involves incorporating reinforcing nanoparticles into the matrix to improve its mechanical and thermal properties. Al6061 hybrid nanocomposites were manufactured using powder metallurgy. Silicon carbide (SiC) ceramic nanoparticles and carbon nanotubes (CNTs) were used as reinforcements. Characterization of the Al6061 hybrid nanocomposites involved analysis of their mechanical properties, such as hardness and tensile strength, as well as their micro and nanometric structures. Techniques such as optical microscopy (OM) and scanning electron microscopy (SEM) with electron backscatter diffraction (EBSD) were used to study the distribution of nanoparticles, the grain size of the microstructure, and the presence of defects in the matrix. The results showed that adding reinforcing nanoparticles can significantly improve the properties of Al6061, depending on the amount and type of nanoparticles. However, the agglomeration of the nanoparticles and the difficulty of uniform dispersion remain challenges in manufacturing these nanocomposites. The microstructural evaluation revealed significant grain refinement and improved homogeneity in the hybrid composites, resulting in enhanced mechanical performance. Tensile tests demonstrated that the hybrid Al6061/CNTs/SiC composite exhibited the highest tensile strength of 104 MPa, compared to 63 MPa for the unreinforced Al6061 matrix.

There is an extensive body of research in the literature focusing on predicting the mechanical properties of concrete, such as compressive strength. Summarizing the current studies following the valuable contributions of researchers will serve as a guide for future studies and researchers. To this end, this study aims to identify the key authors, sources, institutions, and countries that have contributed to the prediction of concrete compressive strength. Additionally, it aims to provide researchers with comprehensive information on prominent research themes, trends, and gaps in the literature related to the prediction of concrete compressive strength. For this purpose, 2319 articles on the prediction of concrete compressive strength published from 2000 to 19th August 2024 were identified through the Scopus Database. The scientific measurement analyses were conducted using VOSviewer software. Upon reviewing the relevant research, it was found that machine learning methods are frequently used in predicting concrete compressive strength. In this context, the study will make significant contributions to the literature by examining leading institutions, countries, authors, and sources in the field, synthesizing data, and highlighting research areas, gaps, and trends related to concrete compressive strength prediction.

Even despite rapid advances in colorectal surgery, morbidity and mortality rates in elective gastrointestinal surgery play a significant role. For decades, there have been tempestuous discussions on preventive measures to minimize the risk of anastomotic dehiscence. When mechanical bowel preparation before elective procedure, one of the key hypotheses, has been introduced into practice, it was assumed that it would decrease number of infectious complications and anastomotic dehiscence. The advancements in antibiotic treatment supported concomitant administration of oral antibiotics and mechanical bowel preparation. In the prospective study conducted at our clinic, we performed left-side colorectal procedures without the prior mechanical preparation. All patients enrolled in the study underwent the surgery and had been observed in the 3rd Surgical Clinic, Faculty of Medicine, Comenius University in Bratislava, Slovakia, from January 2019 to January 2020. As a control group we used similar group of patients with MBP. Our observed group included 87 patients with tumors in the left part of their large intestine (lineal flexure, descendent colon, sigmoid colon, and rectum). Dixon laparoscopic resection was performed in 26 patients. Sigmoid laparoscopic resection was performed in 27 patients. In 12 patients, the procedure was started laparoscopically but had to be converted due to adverse anatomical conditions. The conservative approaches mostly included Dixon resections (19 patients), sigmoid colon resection (5 patients) and left side hemicolectomy (6 patients), and Miles´ tumor resection with rectal amputation (4 patients). Our study highlighted the fact that MBP does not have the unequivocal benefit for patients with colorectal infection, which has an impact on development of anastomotic dehiscence.

An undesirable sensory attribute (“floral taint”) has been recently detected in red wines in some winegrowing jurisdictions in North America (e.g. Ontario, British Columbia, Washington), caused by introduction of frost-killed leaves and petioles [materials-other-than-grapes (MOG)] during mechanical harvest and winemaking. It was hypothesized that terpenes, norisoprenoids, and higher alcohols would be the main responsible compounds. Objectives were to investigate causative volatile compounds for floral taint, and explore threshold concentrations for this problem. Commercial wines displaying varying intensities of floral taints were subjected to GC-MS and sensory analysis. Several odor-active compounds were higher in floral-tainted wines, including terpenes (geraniol, citronellol, cis- and trans-rose oxide), norisoprenoids (β-damascenone, β-ionone), five ethyl esters, and three alcohols. Thereafter, fermentations of Cabernet franc (CF) and Cabernet Sauvignon (CS) (2016, 2017) were conducted. MOG treatments were (wt/wt): 0, 0.5%, 1%, 2% and 5% petioles, and 0, 0.25%, 0.5%, 1%, and 2% leaf blades. Terpenes (linalool, geraniol, nerol, nerolidol, citronellol, citral, cis- and trans-rose oxides, eugenol, myrcene), norisoprenoids (α- and β-ionone), and others (e.g. hexanol, octanol, methyl and ethyl salicylate) increased linearly/quadratically with increasing MOG levels in both cultivars. Principal components analysis separated MOG treatments from the controls with 5% petioles and 2% leaves as extremes. Increasing MOG levels in CF wines increased floral aroma intensity, and were primarily associated with terpenes, higher alcohols, and salicylates. Increased leaf levels in CF were associated with higher vegetal and earthy attributes. Increased petioles in CS were not correlated with floral aromas, but increased leaves increased floral, vegetal and herbaceous attributes. Overall, petioles contributed more to floral taint than leaves through increased terpenes and salicylates (floral notes), while leaves contributed norisoprenoids and C6 alcohols (green notes).

A dynamic impact test was performed on as-rolled AZ31 alloy with gradient microstructure under various strains. The microstructural evolution and mechanical properties were systematically investigated. As the strain rate gradually increases, an increasing number of twins are formed, facilitating dynamic recrystallization (DRX), and the mechanical properties are also gradually improved as well. The microstructure becomes heterogeneous at higher strain rates, but the peak stress decreases. The impact process results in significantly higher performance due to microstructural refinement, work hardening by dislocations and precipitates. In addition, both the adiabatic shear band and the adjacent crack experience a temperature rise that exceeds the recrystallization temperature of the alloy. This observation also explains the presence of ultrafine recrystallized grains within the adiabatic shear band and the appearance of molten metal around the crack.

Mechanical ventilation is a life-saving treatment for critically ill patients who are struggling to breathe independently due to injury or disease. Globally, large numbers of Individuals have always required mechanical ventilation per year. The Covid-19 pandemic elevated the significance of the mechanical ventilation which have played a significant role in sustaining Covid 19 infected critically ill patients who could not breathe on their own. The pandemic drew the attention of the world to the shortage of ventilators globally.This research work presents the formulation of a detailed Port Hamiltonian model of a mechanical ventilator integrated to the human respiratory system. The interconnection and coupling conditions for the various subsystem within the mechanical ventilator and the coupling between the mechanical ventilator and the human respiratory system is also presented.A structure preservation discretization is provided along side numerical simulations and results. The obtained results are found to be comparable to results presented in literature.The future work will include the design of suitable controllers for system.

Growing concerns about the greenhouse effect, global warming, and adverse climate changes primarily stemming from carbon dioxide (CO2) emissions in traditional Portland cement (OPC) used in civil engineering construction, have prompted a shift toward eco-friendly alternatives like geopolymer cement (GPC). Over the last few decades, significant advancements have been made in developing environmentally sustainable pavement construction materials such as GPC to mitigate global CO2 emissions. The success of geopolymer cement (GPC) as an eco-friendly alternative to OPC has garnered attention for its potential to lower carbon emissions and enhance durability. This is attributed to the sustainable production method of GPC, where industrial cementitious waste materials (such as fly ash (FA), metakaolin (MK), mine tailings (MT), slag, etc.) are combined with an eco-friendly alkaline activator and water through the geopolymerization process. Numerous studies on geopolymer concrete indicate that, like OPC, GPC exhibits comparable mechanical properties, including strength, fire resistance, chemical resistance, and durability. This review explores the properties and applications of GPC as a sustainable material in pavement construction, exploring key studies and advancements in geopolymer technology, particularly its suitability for pavement applications. The assessment covers the mechanical properties, long-term performance, and environmental impact of geopolymer-based pavements, providing a comprehensive overview to inform policymakers, engineers, and researchers about the viability of geopolymer-based materials as a sustainable solution for modern pavement construction.

Wood is poised to become a material of choice for future construction. When appropriately managed, it is a renewable material with unique mechanical properties. Beyond its inherent sustainability, the use of wood has a crucial role in addressing climate change concerns due a significantly lower energy consumption and emissions during manufacturing and transportation, while simultaneously acting as a carbon sink. Thus, there has been a growing demand for hardwoods for structural applications, including Castanea sativa Mill., the focal point of this investigation. Albeit in a limited capacity, Eurocode 5-2 offers friction coefficients for softwoods, but it falls short for hardwoods which it is a gap to bridge with this research. These coefficients play a critical role in numerical simulations involving friction, enabling the optimization of joints and, by extension, the overall structural integrity. Test samples were evaluated at 18% moisture content, which is typical of Service Class 2, for various orientations of timber-to-timber and timber-to-steel friction. Considering previous friction coefficients at 12% moisture content, the linear variation was evaluated at an intermediate value of 15%. The results provide an experimental database for numerical simulations and highlight the influence of moisture content on the coefficients, which increase linearly along moisture percentages.

The mechanical pre-treatment constitutes an unavoidable pre-step prior to biofuels conversion. As the cost of this step is often underestimated, recently researchers have striven to identify and characterize the mechanical pre-treatment effects in terms of post-treatment physical characterization, derived improvement of enzymatic digestibility, and output yields. The status of existing mechanical pre-treatment techniques is reviewed by substrate’s typology for lignocellulose biomass, focusing on comminution techniques. Emphasis has been dedicated to the particle size achieved after treatment, crystallinity breakage and eventual inhibitory phenomena deriving from the application of particle size reduction, which are analysed and discussed.

CoCrFeNiMn high-entropy alloy coatings were prepared on compacted graphite iron（CGI） through plasma cladding to strength the CGI substrate. The effects of heat treatment temperatures and times on the microstructure and mechanical properties of the CoCrFeNiMn coatings were investigated. After heat treatment, a single FCC phase was remained in the coating as compared to the deposited one, with smaller dendrites, larger dendritic spacing and more Cr-rich compounds precipitated between dendrites. The coatings’ microhardness was increased after heat treatment. After heat treated at 660°C for 90 minutes, the coating had the highest microhardness of 563±6.9 HV0.2, the lowest frictional coefficient of 0.71 and the smallest wear mass loss of 1.12 mg, and it had the best wear resistance.

In the present work, the effects of ageing treatment on the microstructures of a near-β Ti alloy (TC18) are studied. The influence of ageing treatment on the tensile properties and failure mechanisms are systematically analyzed. It is found that the size and morphology of the primary α (αp) phases are insensitive to ageing temperature and time. Furthermore, the ageing temperature and time dramatically influence the precipitation of the secondary α (αs) phases. Massive αs phases precipitate and gradually coarsen, and finally weave together with increasing the ageing temperature or extending the ageing time. The thickness of αs phases is responsible for the material strengths, while the content of α phases can enhance the material ductility. The ductile characteristics of the alloy with coarser αs phases are more obvious than those with thinner αs phases. Therefore, the ageing treatment is helpful for the precipitation and homogeneous distribution of αs phases, which is essential for balancing the strengths and ductility of the studied Ti alloy.

Lightweight component design is effectively achievable through the sandwich structures, many past research studies in the aerospace and racing sectors (since 1920s) has proven it. To extend their application into automotive and other transport industries, the manufacturing cycle times must be reduced. This can be achieved by thermoplastic sandwich materials of continuous fibre-reinforced thermoplastic (CFRTP) cover layers and thermoplastic honeycomb cores. To widespread the application of flat thermoplastic-based sandwich panels into complex parts, a novel forming technology was developed by the Fraunhofer Institute of Microstructure of Materials and Systems (IMWS). For an increase in reproducibility of the sandwich component production and a decrease in manufacturing defects, numerical modelling methods and experimental validation are needed. The finite element (FE) modelling of this thermoforming process is a thermo-mechanical assignment with all three: material, geometry, and boundary non-linearities. In the scope of this work, the material behavior of different sandwich components (cover layers, honeycomb core, interface) under thermo-mechanical loads is characterized in detail, and a complex numerical model is developed to describe the thermoforming process of thermoplastic-based sandwich laminate. The critical forming condition like wrinkling that occurs due to friction in a sandwich or poor intra-ply shear in cross-ply studied, validated, and optimized. A thermoplastic sandwich made of polypropylene (PP) honeycomb core and polypropylene glass fibre (PP/GF) cross-ply as cover layers was used for this study, and numerical modelling was executed in LS-DYNA software.

In order to address the issues of weight, cost and sustainability issues associated with the application of glass fibre in structural composites, plant fibres are proposed as an alternative to reduce and replace the usage of glass fibres. Despite this, there is still a gap in comprehensive research on plant fibre composites, especially with regard to their durability in real structural applications. This research investigates the fatigue and impact properties of pultruded hybrid polyester composites reinforced with glass fibre and kenaf, tailored for structural applications. Utilising kenaf fibres in mat form, unidirectional glass fibre direct roving yarns and unsaturated polyester resin as key components, pultruded kenaf/glass hybrid profiles were meticulously fabricated. Comparative cost and weight analyses were conducted between pultruded hybrid and non-hybrid profiles. The study showed that the pultruded kenaf/glass alternative laminates exhibit commendable fatigue and impact resistance, making them suitable for use in moderately loaded structural applications. Moreover, the use of kenaf as a hybrid alternative shows significant cost and weight reductions. This research provides a basis for the development of sustainable and efficient structural materials and highlights the significant role of material design in shaping the future of engineering applications.

The current work shows the optimization in the preparation of nanosized titanium carbide (TiC) in-situ through mechanical alloying (MA). Metallic titanium (Ti) powders, along with two carbon sources, carbon nanotubes (CNTs), and stearic acid (SA), were used to reduce the particle size using a high-energy Spex800 mill. The combined use of 2 wt % of these carbon sources and n-heptane as a liquid process control agent (PCA) proved crucial in generating nanoscale powder composites through a simple and scalable synthesis process within a 4-hour timeframe. The use of 20 wt % of both carbon sources was compared to determine the ability of CNTs to form carbides and the decomposition of PCAs during mechanical milling. The result reveals structures like nanoblocks and nanolumps with and important size reduction. The structure and morphology of the composites and starting materials were evaluated through x-ray diffraction (XRD), Raman spectroscopy, scanning electron microscopy (SEM), and transmission electron microscopy (TEM).

Compared to tin lead alloys, lead-free tin alloys have lower toxicity, making them more widely used. In this study, Sn-20Bi-0.3Al-xY solders alloys were prepared. The effects of the addition of Y on its microstructure, micro-hardness, wettability and mechanical properties was investigated. The result showed that the addition of Y had significant effect on the refinement of Sn-20Bi-0.3Al-xY. From the spreading tests results, Y increased the wettability of the solders, however when the fraction of Y gradually increased, the wettability reduced. The ultimate tensile and hardness of Sn-20Bi-0.3Al-xY solders alloys were increased as the content of Y increasing.

It is generally accepted that the human abdominal wall is comprised of skin, subcutaneous tissues, muscles and their aponeuroses, and the parietal peritoneum. Understanding these layers and their mechanical properties provides valuable information to those designing procedural skills trainers, supporting surgical procedures (hernia repair), and engineering-based work (in silico simulation). However, there is little literature available on the mechanical properties of the abdominal wall in layers or as a composite. This work characterizes the tensile properties of the human abdominal wall by layer and as a partial composite. Tissues were collected from fresh-never-frozen and fresh-frozen cadavers and tested in uniaxial tension at a rate of 5 mm/min until failure. Stress-strain curves were created for each sample, and the values for elastic moduli, ultimate tensile strength, and strain at failure were obtained. The experimental outcomes from this study demonstrated variation of tensile properties within and between tissues. The data also suggest that the tensile properties of composite abdominal walls are not additive. Ultimately, this body of work contributes to a deeper comprehension of these mechanical properties and will serve to enhance patient care, refine surgical interventions, and assist with more sophisticated engineering solutions.

The present study aimed to evaluate the effect of the citric acid on the properties of solid pine wood, which were submitted to thermomechanical treatment. A preliminary test was performed in a previous study to evaluate the influence of different temperatures of pressing and concentrations of citric acid over the physical properties of wood. After choosing the best treatments (170°C and 5% and 10% of citric acid) it was evaluated the effect of these on the chemical properties (SEM, FTIR and pH), on the density profile using an X-ray microtomography, and on the resistance to ageing through abrasion test. The result of the chemical analysis allowed to observe an increase of the presence of ester functional groups, as well as a better coverage and higher acidity of the surface. The density profile technique allowed to observe the formation of peaks of density on the surface where the acid was applied. Lastly, it was also possible to verify an increase in the resistance to abrasion because of the application of the citric acid.

Abstract: The chemical mechanical polishing (CMP) has been widely used for surface modification of critical materials and components and provided global planarization of topography with a low post-planarization slope high quality and efficiency. The colloidal silica slurries play an important role in the finishing processes of optical components. Monodisperse mesoporous silica nanospheres were synthesized with different surfactant by Stöber method. Their architectural features and texture parameters were characterized by XRD, FTIR, N2 adsorption–desorption isotherms, SEM, XPS, and TGA techniques. The spherical SiO2 products presented with the controllable 50-150 nm particle size and distribution. The AFM micrographs reveal that flat and smooth surfaces without distinct scratches residual particles are achieved by using the as-obtained composite particles as abrasives[The particle size of SiO2 slurry plays a critical role in the chemical-mechanical polishing process.

The dolomite dust-emulsified asphalt composite with excellent mechanical properties was successfully prepared using alkali activation. The effects of different alkali concentrations and emulsified asphalt contents on the mechanical properties of the materials were studied. The mechanical properties and microstructure of the composites were analyzed using compressive strength tests, bending strength tests, and SEM characterization. The experimental results show that the specimens have excellent mechanical properties: the 7-day compressive strength can reach 76.67 MPa, and the bending strength is about twice that of silicate-based geopolymer-emulsified asphalt composite. With an increase in emulsified asphalt content, the compressive strength of the samples decreases, while the bending strength increases first and then decreases. When the emulsified asphalt content is 1%, the bending strength of the sample is up to 28.81 MPa, which is 25% higher than that of the sample without emulsified asphalt. This indicates that an appropriate emulsified asphalt content can play a toughening role in the system, providing a new idea for designing high-toughness alkali-activated materials.

The impact induced by cavitation bubble collapse can be utilized for mechanical surface treatment to improve fatigue properties of metals including additive manufactured metallic materials. A peening method using cavitation impact induced by a pulsed laser is called “laser cavitation peening (LCP)”. Normally, a Q-switched Nd:YAG laser, whose pulse width is a few nanoseconds, is used for LCP, which improves the fatigue strength. The problem with LCP is that the processing time is too slow. If a laser pulse whose pulse width is a few hundred microseconds can be utilized for LCP, the repetition frequency can be increased drastically using other types of laser systems such as a fiber laser. In the present paper, in order to reveal the possibility of LCP using a pulsed laser width of a few hundred microseconds, the use of LCP with a normal-oscillation Nd:YAG laser (pulse width ≈ 200 us) was investigated. It is demonstrated that LCP with the normal-oscillation Nd:YAG laser produced curvature in an aluminum alloy plate.

Abstract: To compare the use of variable mechanical ventilation with conventional mechanical ventilation in porcine model of ARDS. Methods: Animals were divided into two groups (n = 6), conventional ventilation and variable ventilation with bi-oscillatory PEEP. For induction of ARDS, intravenous oleic acid was used until a P/F ratio of 200 to 300 mmHg. The animals were ventilated with pressure control, FiO2 1.0, inspiration-expiration ratio = 1:2, tidal volume 6 ml/kg with the initial respiratory rate adjusted to maintain an end tidal CO2 tension of 35 to 45 mmHg. Variable ventilation was characterized by the oscillation of PEEP from 5 to 10 cmH2O every 4 respiratory cycles, in convencional ventilation group PEEP was set from 5 cmH2O. Ventilatory, hemodynamic parameters, oxidative stress, antioxidant enzymes, Interleukin 8 (IL8) and 17-a (IL17a) and histological analyzes were evaluated; Results: The use of BiPEEP demonstrated improvement in lung compliance and PaO2 in relation to control. The levels of oxidative stress and antioxidant enzymes showed no significant difference. There was no difference in IL17a between groups. In IL8 there was a significant increase in the lung base of control in relation to BiPEEP, and a reduction in the apex of BiPEEP in relation to control. The control group showed changes in lung morphology characterized by cellular infiltrates, a thickening of the alveolar septae and atelectasis, which were attenuated in BiPEEP group; (4) Conclusions: The use of variable ventilation with bi-oscillatory level of PEEP demonstrates a potential ventilatory strategy in an experimental model of ARDS.

Advanced coatings are essential to modern technologies, as they optimise surface characteristics for different application scenarios. Transparent and self-cleaning coatings are increasingly used as protective coatings for various applications, such as foldable touchscreens, windows, and solar panels. Moreover, incorporating other functionalities such as high hardness, wear resistance, and flexibility into transparent and self-cleaning coatings is important for broadening the use cases. Although many kinds of multifunctional coatings have been developed, it is still difficult to embody several properties in one coating adequately, as some properties, such as hardness and flexibility, are inherently contrastive. This review first describes basic principles, including wetting ability, photocatalytic reactions, photo-induced hydrophilic phenomena, and the implication of self-cleaning. The desired properties of multifunctional coatings are then listed, and methods for evaluating different properties are used. Recent progress in various preparation methods for multifunctional coatings, including the sol-gel, dip/spin, and chemical vapour deposition (CVD) methods, are also presented. Magnetron sputtering (MS) technology is widely used in coating preparation. Compared with chemosynthesis and CVD, MS is time-saving, suitable for industrial production, and environmentally friendly. Coatings prepared by MS usually possess excellent mechanical properties. Thus, we highlight the current research status of MS technology in multifunctional coating preparation. Moreover, according to the multilayer design structure of coatings, their optical and mechanical properties and self-cleaning ability can be controlled by combining the characteristics of different materials. Finally, combining photocatalytic materials such as TiO2 with other materials through a multilayer structure to obtain a multifunctional coating with excellent overall properties is discussed.

Hydrogel-based wearable electrochemical biosensors (HWEBs) are emerging biomedical devices that have recently received immense interest. The exceptional properties of HWEBs include excellent biocompatibility with hydrophilic nature, high porosity, tailorable permeability, the capability of reliable and accurate detection of disease biomarkers, suitable device-human interface, facile adjustability, and stimuli-responsive to the nanofiller materials. Although the biomimetic three-dimensional hydrogels can immobilize bioreceptors, such as enzymes and aptamers, without any loss in their activities. However, most HWEBs suffer from low mechanical strength and electrical conductivity. Many studies have been performed on emerging electroactive nanofillers, including biomacromolecules, carbon-based materials, and inorganic and organic nanomaterials, to tackle these issues. Non-conductive hydrogels and even conductive hydrogels may be modified by nanofillers as well as redox species. All these modifications have led to the design and development of efficient nanocomposites as electrochemical biosensors. In this review, both conductive-based and non-conductive-based hydrogels derived from natural and synthetic polymers are systematically reviewed. The main synthesis methods and characterization techniques are addressed. The mechanical properties and electrochemical behavior of HWEBs are discussed in detail. Finally, the prospects and potential applications of HWEBs in biosensing, healthcare monitoring, and clinical diagnostics are highlighted.

This study investigated the impact of boron and copper on the microstructure and mechanical properties of Spheroidal graphite Cast Iron (SCI). The addition of boron increased the ferrite content, while copper increased the stability of pearlite. The interaction between boron and copper significantly increased the ferrite content. Differential Scanning Calorimetry (DSC) revealed that boron decreased the enthalpy change of the α + Fe3C -> γ transformation and increased the enthalpy change of the α -> γ transformation. The addition of boron and copper reduced the tensile and yield strength but increased elongation and impact energy. The findings provide valuable insights into the effect of boron and copper on SCI, facilitating the design and development of high-performance SCI materials.

This paper mainly used database technology, machine learning, thermodynamic calculation, experimental verification, etc., on integrated computational materials engineering. The interaction between different alloying elements and the strengthening effect of precipitated phases are investigated mainly for martensitic ageing steels. Modelling and parameter optimization were performed by machine learning, and the highest prediction accuracy was 98.58%. Investigated the influence of composition fluctuation on performance and correlation tests to analyze the influence of elements from multiple perspectives. Furthermore, screen out the three-component composition process parameters with composition and performance with high contrast. Thermodynamic calculations studied the effect of alloying element content on the nano-precipitation phase, Laves phase, and austenite in the material. The heat treatment process parameters of the new steel grade were also developed based on the phase diagram. A new type of martensitic ageing steel was prepared by selected vacuum arc melting. The sample with the highest overall mechanical properties had a yield strength of 1887 MPa, a tensile strength of 1907 MPa, and a hardness of 58 HRC. The sample with the highest plasticity had an elongation of 7.8%. The machine learning process for the accelerated design of new ultra-high tensile steels was found to be generalizable and reliable.

In order to produce nanostructured Ti0.9Cr0.1C powders, an elemental powder mixture of titanium, chromium, and graphite is milled in this work using a high-energy ball mill for various milling times. Microstructural characteristics such as crystallite size, microstrain, lattice parameter, and dislocation density are determined using X-ray diffraction (XRD). Mechanical alloying successfully produced nanocrystalline (Ti,Cr)C with an average crystallite size of 11 nm. This size of the crystallites is also directly verified using transmission electron microscopy (TEM). Scanning electron microscopy (SEM) was used to investigate the morphology of the samples. The novelty of this work is advancing the scientific understanding of the effect of milling time on the particle size distribution and crystalline structure, and also understanding the effect of the spark plasma sintering on the different properties of the bulks. Densified cermet samples were produced from the nanocrystalline powders, milled for 5, 10 and 20 hours by SPS process at 1800 degrees for 5 min under a pressure of 80 MPa. Phase changes of the produced cermets were examined according to XRD, SEM/EDX analyses. Significant amounts of Cr and Fe elements were detected, especially in the 20 h milled cermet. The bulk forms of the milled powders for 5 and 20 h had a relative density of 98.43 and 98.51 %, respectively. However, 5 h milled cermet had 93.3 HRA because of the more homogeneous distribution of the (Ti,Cr)C phase, the low iron content and high relative density. According to the 0.0011 mm/year corrosion rate, and 371.68 kΩ*cm2 charge transfer resistance obtained from the potentiodynamic polarization and EIS tests, the 20 h cermet was the specimen with the highest corrosion resistance.

The solid-state welding method known as friction stir welding (FSW) bonds two metallic work parts, whether the same or different, by plastically deforming the base metal. The frictional resistance between both metallic work pieces causes them to produce heat, which produces plastic deformation and welds them. However, the weldability and strength of FSW joints mainly depend on the FSW parameters. This review work highlights the previous research work on the FSW parameters and their effects on the weldability and quality of the aluminum alloys joined with similar and dissimilar metals through the FSW method. About 150 research studies were systematically reviewed, and the articles included data from peer-reviewed journals. It has been concluded that the key parameters, including welding speed, “rotational speed”, “plunge depth”, “spindle torque”, “shoulder design”, “base material”, “pin profile” and “tool type", significantly affect the weldability of the aluminum joint through the FSW method. Also, the selection of these parameters is important and fundamental as they directly affect the joint. It is recommended that future work focus on FSW for aluminum. Among these, the most essential is the application of artificial intelligence (AI) techniques to select the optimum FSW parameters for aluminum welding.

Time and cost-efficient techniques are essential to avoid extra conventional experimental studies with large date-set to characterize the mechanical properties of composite materials. Correlation between the structural performance and mechanical properties could be captured through the efficient predictive models. Several ensembled Machine Learning (ML) methods were implemented in this study, to materially characterize carbon nanotube (CNT)-reinforced cement-based composites. Proposed models were compared with each other to represent the accuracy of each method. The Flexural and Compressive Strength (target values) of CNT reinforced composites were predicted based on the data-rich framework provided in previous experimental investigations. These data were utilized for training of the proposed models by employing SciKit-Learn library in Python, followed by hyper-parameter tuning and k-fold cross-validation method for obtaining an efficient model to predict the target values. Random Forest (RF) and Gradient Boosting Machine (GBM) were developed for this purpose. The findings of this study would be useful for prospective composite designers in case of sufficient experimental data availability for ML model training.

The paper contains the results of the 100-hour test campaign of the Additive Manufactured (AM) spare part (retainer – slipper) dedicated for an exact axial piston pump. The material of the retainer-slipper has been identified by using energy dispersive spectroscopy and replaced by other – with similar material properties as the original one. The obtained spare part had been subjected to only one postprocessing type (sandblasting) to analyze the influence of the rough part after the AM process. The whole test campaign has been divided into stages, where after each stage microscopic measurements have been made. During microscopical investigation roughness and geometrical measurements were conducted. The results revealed that it is possible to replace parts in hydraulic pumps with the use of AM. 100-hour test campaign caused about 500% increase in the surface roughness of the pump’s original part which was cooperated with the AM spare retainer-slipper, without any damages to the test system.

Closed timelike curves (CTCs), non-intuitive theoretical solutions of general relativity field equations can be modelled in quantum mechanics in a way, known as Deutsch-CTCs, to circumvent one of their most paradoxical implications, namely, the so-called grandfather paradox. An outstanding theoretical result of this model is the demonstration that in the presence of a Deutsch-CTC a classical computer would be computationally equivalent to a quantum computer. In the present study, the possible implications of such a striking result for the foundations of quantum mechanics and the connections between classicality and quantumness are explored. To this purpose, a model for fundamental particles that interact in physical space exchanging carriers of momentum and energy is considered. Every particle is then supplemented with an information space in which a probabilistic classical Turing machine is stored. It is analysed whether, through the action of Darwinian evolution, both a classical algorithm coding the rules of quantum mechanics and an anticipation module might plausibly be developed on the information space from initial random behaviour. The simulation of a CTC on the information space of the particle by means of the anticipation module would imply that fundamental particles, which do not possess direct intrinsic quantum features from first principles in this information-theoretic Darwinian approach, could however generate quantum emergent behaviour in real time as a consequence of Darwinian evolution acting on information-theoretic physical systems.

The petrographic and petrophysical characteristics of three varieties of ignimbrites used in the architectural heritage of Arequipa (southwest Peru) are analyzed. The modal classification QAFP and TAS diagram discriminate their dacitic nature. Mercury injection porometry revealed very high porosity: 46.5% for white and beige ignimbrites and 35.5% for the pink variety. Ignimbrites contain intrusions of vulcanodetrital fragments and vacuoles that influence their predominantly non-linear mechanical behavior. Results of water absorption by capillarity (C) and ultrasound pulse velocity (UPV) demonstrated a slight anisotropy for the beige variety and near isotropy for white and pink ignimbrites, which justify the randomness of the application of the ashlars in the masonry and in the selection of the faces to carve. Surfaces with hollows in the white and beige ignimbrites are the result of the erosion of the acicular pumice that fills the vacuoles.

The concern about consuming eco-friendly products has motivated research in the development of new materials. Therefore, films based on natural polymers have been used to replace traditional polymers. This study consists of a production of films based on gelatin reinforced with black pepper essential oil-loaded nanoemulsions and Cloisite Na⁺. The films were characterized by water vapor permeability, mechanical and thermal properties, surface contact angle, X-ray diffraction and scanning electron microscopy. It was observed that the films containing the nanoemulsion have higher permeability values and an increase in their mechanical resistance. The addition of nanoclay contributed to an increase in the surface hydrophobicity of the film and an increase in the tensile strength at break by about 150%. The addition of essential oil nanoemulsions led to an increase in thermal stability. The presence of clay dispersion contributed to the formation of a surface that was slightly rougher and grainier. The addition of the black pepper essential oil nanoemulsion resulted in an increase in porosity of the gelatin matrix. Through X-ray diffraction analysis, it was possible to conclude that both the polymeric gelatin matrix and the essential oils nanoemulsion are intercalated with the clay dispersion.

A better understanding of diseases progress in tissues vest on the accurate understanding of tissues under mechanical loading. Also, development of therapies for injuries may depend on the available mechanical data for soft tissues. In this study, the raw data of biaxial tensile testing of sclera soft tissue is presented in this paper. Biaxial mechanical testing of soft tissues presents details understanding of how soft tissues behave when compared to uniaxial testing. Biomechanical properties of soft tissues are vital in the development of accurate computational models. Reliable computational models of studying mechanisms of diseases depends mainly on the accurate and more details mechanical behavior of soft tissues. These accurate and detailed computational models may be utilized to further develop the understanding and therapies of various diseases. The mechanical tensile testing was conducted on the passive sheep sclera. Engineering stress vs strain of several samples of the sheep sclera are further presented determined from force and displacement experimental data. The goal of this paper is to make available biaxial data of sheep sclera soft tissue that can be further utilized.

The strictness of the result of an excavation, whether mechanical or by means of explosives, is naturally conditioned by the objective, and therefore by the type of technique applied to achieve it. To attain the best results in terms of rock breakage and respect of the final profile, it’s important to evaluate the excavation specific energy and its optimization. This research focuses on evaluating the effects of different techniques on the quality of final walls in open-pit and underground operations. Different geometries and configurations can be applied to both quarrying and tunnelling blasts. The research is aimed to push contour blasts to their limits, and the main aspects are discussed in order to improve the blast parameters in the daily practice.

Aim: The aim of this study was to estimate the number of nurses who independently care for pa-tients with severe respiratory failure receiving mechanical ventilation (MV) or veno-venous ex-tracorporeal membrane oxygenation (VV-ECMO). Additionally, the study analyzed the actual role of nurses in the treatment of patients with MV and VV-ECMO. Methods: We conducted a cross-sectional study using postal surveys. The study included 725 Japanese intensive care units (ICUs). Descriptive statistics were conducted. Results: Among the 725 ICUs, we obtained 302 re-sponses (41.7%) and analyzed 282 responses. The median number of nurses per bed was 3.25. The median proportion of nurses who independently cared for patients with MV was 60% [IQR: 42.3-77.3]. The median proportion of nurses who independently cared for patients with VV-ECMO was 46.9 (35.7-63.3%) in the ICU experiencing VV-ECMO use. Concerning task-sharing, 33.8% of ICUs and nurses did not facilitate weaning from MV. Nurses always ti-trated sedatives in 44.5% of ICUs. Conclusion: Nurse staffing might be inadequate in all ICUs, es-pecially for severe respiratory failure. The proportion of competent nurses for caring for severe respiratory failure in ICUs should be considered when determining the work force of nurses.

Shape-memory hydrogels (SMH) are as multifunctional, actively-moving polymers of interest in biomedicine. In loosely crosslinked polymer networks gelatin chains may form triple helices, which can act as temporary netpoints in SMH, depending on the presence of salts. Here, we show programming and initiation of the shape-memory effect of such networks based on a thermomechanical process compatible with the physiological environment. The SMH were synthesized by reaction of glycidylmethacrylated gelatin with OEG α,ω-dithiols of varying crosslinker length and amount. Triple helicalization of gelatin chains is shown directly by wide-angle X-ray scattering and indirectly via the mechanical behavior at different temperatures. The ability to form triple helices increased with the molar mass of the crosslinker. Hydrogels had storage moduli of 0.27-23 kPa and Young’s moduli of 215-360 kPa at 4 °C. The hydrogels were hydrolytically degradable, with full degradation to water soluble products within one week at 37 °C and pH = 7.4. A thermally-induced shape-memory effect is demonstrated in bending as well as in compression tests, in which shape recovery with excellent shape recovery rates Rr close to 100% were observed. In the future, the material presented here could be applied e.g. as self-anchoring devices mechanically resembling the extracellular matrix.

Fired bricks have shown tremendous potential as a construction material due to their properties. However, their use required some specifications in terms of quality, resistance, and durability. In developing countries, the lack of tools to make test specimens leads to many defects in these brick specimens responsible for low durability and weak precision during mechanical tests and shrinkage. In this study, a simple and traditional method of making test bricks is presented. This simple method allows the production of bricks with the required properties. This method is especially efficient for a firm or semi-soft pastes consistency. The handmade pastes do not stick into the walls of the mold like the case of steel molds and it gives specimens with standard shape, smooth surface, and sharp edges. The resulting fired bricks exhibit high mechanical strength comparable and even better than those of conventional methods.

The effect of rare earth Pr6O11 on the microstructure and mechanical properties of high-strength steel weld metal was investigated by optical microscopy, scanning electron microscopy and mechanical testing. Three different contents of Pr6O11 were added to the flux-cored wires. The results showed that the addition of 1% Pr6O11 can promote the refinement and spheroidization of inclusions, refine the grains, form acicular ferrites, and significantly improve the toughness of weld metal. The addition of Pr6O11 promoted the formation of rare earth composite inclusions and acicular ferrites in the weld metal, refined the lath microstructure, inhibited the formation of martensite and bainite. The crack formation mode changed from the boundary cracking of the bainite clusters caused by the surface shear stress to the surface shear stress-induced decohesion of inclusion. However, excessive addition of Pr6O11 will reduce the number of inclusion nucleation and deteriorate the mechanical properties. The wire No.2 with 1% Pr6O11 had the good comprehensive mechanical properties, and the corresponding values were 835MPa of tensile strength and 72 J of impact toughness. These findings suggest that the control of Pr6O11 can be an effective way to improve the impact toughness of weld metal.

The effect of Pr6O11 on the microstructure and mechanical properties of high-strength steel weld metal was investigated by optical microscopy, scanning electron microscopy and mechanical testing. Three different contents of Pr6O11 were added to the flux-cored wires. The results demonstrate that the addition of 1% Pr6O11 can promote the refinement and spheroidization of inclusions, refine the grains, form acicular ferrites in the weld metal, and significantly improve the toughness. The addition of Pr6O11 promoted the formation of rare earth composite inclusions and acicular ferrites in the weld metal, refined the lath microstructure, inhibited the formation of martensite and bainite. The crack formation mode changed from the boundary cracking of the bainite clusters caused by the surface shear stress to the surface shear stress-induced decohesion of inclusion. Excessive addition of Pr6O11 will reduce the number of inclusion nucleation and deteriorate the mechanical properties. The wire No.2 with 1% Pr6O11 had the good comprehensive mechanical properties.

Regional mechanics of the heart is vital in the development of accurate computational models for the pursuit of relevant therapies. Challenges related to heart dysfunctioning are the most important sources of mortality in the world. For example, myocardial infarction (MI) is the foremost killer in sub-Saharan African countries. Mechanical characterisation plays an important role in achieving accurate material behaviour. Material behaviour and constitutive modelling are essential for accurate development of computational models. In most cases previously, the mechanical properties of the heart myocardium were assumed to be homogeneous. The main objective of this paper is to determine the mechanical material properties of healthy porcine myocardium in three regions, namely left ventricle (LV), mid-wall/interventricular septum (MDW) and right ventricle (RV). The biomechanical properties of the pig heart RV, LV and MDW were characterised using biaxial testing. The biaxial tests show the pig heart myocardium behaves non-linearly, heterogeneously and anisotropically. In this study, it was shown that RV, LV and MDW may exhibit slightly different mechanical properties. Data presented here may be helpful in regional tissue mechanics, especially for the understanding of various heart diseases and development of new therapies.

We demonstrate high quality (intrinsic Q factor ~2.8×106) racetrack microresonators fabricated on lithium niobate (LN) thin film with a free spectral range (FSR) of ~86.38 pm. By integrating microelectrodes alongside the two straight arms of the racetrack resonator, the resonance wavelength around the 1550 nm can be red shifted by 92 pm when the electric voltage is raised from -100 V to 100 V. The microresonators of the tuning range spanning over a full FSR is fabricated using photolithography assisted chemo-mechanical etching (photolithography assisted chemo-mechanical etching, PLACE).

Background: The main factors to influence on the stroking performance of club head are alloy and spring-like effect. Design the structure of new club face to create the fairway wood which can show best stroking feeling and let driving distance become longer. Purpose: The club face of fairway wood is processed through the iron alloy heating procedure and CNC to innovate the club head with high spring-like effect (characteristic time). Method: (1) Use 455 stainless steel processed by heating and aging treatment, to do the analysis on microstructure and mechanical properties. (2) Through CNC to design seven different patterns for the back of club face, each pattern for three club head. The total amount is twenty-one. (3) Make finished product be test the characteristic time and the ability of strike by the practical measurement. (4) To analyze after the compare between three-way ANOVA and LSD. Results: After 455 stainless steel was heated in procedure S850℃-A550℃, mechanical properties became superior and had the better malleability, it is suitable for developing the club face of high spring-like effect. Before and after grinding among three-way ANOVA (pattern*thickness*place), did not achieve the significant level on the figure of characteristic time. Through two-way ANOVA (pattern*place and thickness*place), showed the significant deviation before and after grinding. After doing the crash test by 45m/s, all the results can reach the higher limited standard. Summary: 455 stainless steel was designed with the different club face’s thicknesses of fairway wood can make spring-like effect achieve high characteristic time. The much thinner club face let the characteristic time perform highly. But there was no obvious effects from the patterns of the back club face.

Mortarless refractory masonry structures are widely used in the steel industry for the linings of many high-temperature industrial applications including steel ladle. The design and the optimization of these components require accurate numerical models that consider the presence of joints as well as joints closure and opening due to cyclic heating and cooling. The present work reports on the formulation, numerical implementation, validation, and application of homogenized numerical models for simulation of refractory masonry structures with dry joints. The validated constitutive model has been used to simulate a steel ladle and to analyze its transient thermomechanical behavior during a typical thermal cycle of steel ladle. 3D solution domain, enhanced thermal and mechanical boundary conditions have been used. Parametric studies to investigate the impact of joints thickness on the thermomechanical response of the ladle have been carried out. The results clearly demonstrate that the thermomechanical behavior of mortarless masonry is orthotropic nonlinear due to gradual closure and reopening of joints with the increase and decrease of temperature. Also, resulting thermal stresses increase with the increase of temperature and decrease with the increase of joints thickness.

In this paper, the effect of preheating on the mechanical properties and micro structure of similar friction stir welded AA6061 aluminum alloys sheets was investigated. Aluminum alloy 6061 sheets with a thickness of 5 mm and threaded cylindrical pins were used. Rotation and traverse speeds were 1200 rpm and 75 mm/min, respectively. The results of tensile tests performed on the welded samples showed that compared to the non-preheated samples, preheating had increased the strength and elongation of the joints by 58% and 46%, respectively. In the present study, during the welding process preheating cause emerged heat with lower slope from stir zone. This phenomenon may result in Increase the deformation resistance of material and consequently decrease of grain size. This grain refinement can improve the mechanical properties of welds. Accordingly, hardness and strength of the material will be increased.

The effect of reprocessing on the quasi-static uniaxial tensile behavior of two commercial polypropylene (PP) based composites is experimentally investigated and modeled. In particular, the studied materials consist of an unfilled high-impact PP and a talc-filled high-impact PP. These PP composites are subjected to repeated processing cycles including a grinding step and an extrusion step to simulate recycling at the laboratory level, the selected reprocessing numbers for this study being 0, 3, 6, 9 and 12. Because the repeated reprocessing leads to thermo-mechanical degradation by chain scission mechanisms, the tensile behavior of the two materials exhibits a continuous decrease of elastic modulus and failure strain with increasing number of reprocessing. A physically consistent three-dimensional constitutive model is used to predict the tensile response of non-recycled materials with strain rate dependence. For the recycled materials, the reprocessing effect is accounted by incorporating the reprocessing sensitive coefficient into the constitutive model for Young’s modulus, failure strain, softening and hardening equations. Our predictions of true stress - true strain curves for non-recycled and recycled 108MF97 and 7510 are in a good agreement with experimental data.

Polymer flooding is an established enhanced oil recovery (EOR) method, still many aspects of polymer flooding are not well understood. This study investigates the influence of mechanical degradation on flow properties of polymers in porous media. Mechanical degradation due to high shear forces may occur in the injection well and at the entrance to the porous media. The polymers that give high viscosity yields at a sustainable economic cost are typically large, MW > 10 MDa, and have wide molecular weight distributions. Both MW and the distributions are altered by mechanical degradation, leading to changes in the flow rheology of the polymer. The polymer solutions were subjected to different degrees of pre-shearing and pre-filtering before injected into Bentheimer outcrop sandstone cores. Rheology studies of injected and produced polymer solutions were performed and interpreted together with in-situ rheology data. The core floods showed a predominant shear thickening behavior at high flow velocities which is due to successive contraction/expansion flow in pores. When pre-sheared, shear thickening was reduced but with no significant reduction in in-situ viscosity at lower flow rates. This may be explained by reduction in the extensional viscosity. Furthermore, the results show that successive degradation occurred which suggests that the assumption of the highest point of shear which determines mechanical degradation in a porous media does not hold for all field relevant conditions.

High-performance poly(1,4-butylene terephthalate (PBT) nanocomposites have been developed via the consideration of phosphorus-containing agents and amino-carbon nanotube (A-CNT). One-pot functionalization method has been adopted to prepare functionalized CNTs via the reaction between A-CNT and different oxidation state phosphorus-containing agents, including chlorodiphenylphosphine (DPP-Cl), diphenylphosphinic chloride (DPP(O)-Cl), and diphenyl phosphoryl chloride (DPP(O3)-Cl). These functionalized CNTs, DPP(Ox)-A-CNTs (x = 0, 1, 3), were respectively mixed with PBT to obtain the CNTs-based polymer nanocomposites through a melt blending method. SEM observations demonstrated that DPP(Ox)-A-CNT nano-additives were homogeneously distributed within PBT matrix compared to A-CNT. The incorporation of DPP(Ox)-A-CNT improved the thermal stability of PBT. Moreover, PBT/DPP(O3)-A-CNT showed the highest crystallization temperature and tensile strength, due to the superior dispersion and interfacial interactions between DPP(O3)-A-CNT and PBT. PBT/DPP(O)-A-CNT exhibited the best flame retardancy resulting from the excellent carbonization effect. The radicals generated from decomposed polymer were effectively trapped by DPP(O)-A-CNT, leading to the reduction of heat release rate, smoke production rate, carbon dioxide and carbon monoxide release during cone calorimeter tests.

We focus on macromolecules which are modelled as sequentially growing dual scale-free networks. The dual networks are built by replacing star-like units of the primal treelike scale-free networks through rings, which are then transformed in a small-world manner up to the complete graphs. In this respect, the parameter γ describing the degree distribution in the primal treelike scale-free networks regulates the size of the dual units. The transition towards the networks of complete graphs is controlled by the probability p of adding link between non-neighbouring nodes of the same initial ring. The relaxation dynamics of the polymer networks is studied in the framework of generalized Gaussian structures by using the full eigenvalue spectrum of the Laplacian matrix. The dynamical quantities on which we focus here are the averaged monomer displacement and the mechanical relaxation moduli. For several intermediate values of the parameter’s set (γ, p) we encounter for these dynamical properties regions of constant in-between slope.

Implant-supported-screw-retained prostheses are really popular. Some of the most frequent complications have been mechanical complications. These include abutment screw loosening or even screw fracture. Using an intermediate abutment can offer several advantages. However, little literature has been found regarding how this affects the mechanical behavior of dental restorations. This study focuses on understanding the mechanical behavior of implant-supported restorations with a transepithelial component compared to those with a direct implant-supported restoration. It was carried out by using the Finite Element Method (FEM) and was experi-mentally validated. The results showed that in the case of transepithelial-supported restoration, the prosthetic screw mounted over the transepithelial component suffers higher stress than the one screwed directly to the implant. After applying a cyclic fatigue load, it is experimentally proven that, in the transepithelial-supported restorations, the fuse changes from being the screw that goes to the implant, to being the upper one. As a conclusion we can say that the use of an intermediate abutment in dental restoration not only provides better protection to the rest of the dental restoration but also allows easier repair in the event of a fracture. This can potentially lead to more efficient procedures and improved patient outcomes.

The use of acoustic and magnetic methods of non-destructive testing to detect zones of stable localization of deformation in order to assess and predict the performance of long-term equipment is of scientific and practical interest at present. A structural-mechanical criterion has been developed, that reflects the revealed relationships between the structural and substructural states, internal stress fields and stable localization of deformations with the characteristics of non-destructive tests in the metal of long-term equipment made of structural 0.2 С steel and heat-resistant 0,12C-1Cr-1Mo-1V steel. The values of the structural-mechanical criteria Ks.-m for structural 0.2 С steel and for heat-resistant 0,12C-1Cr-1Mo-1V steel, corresponding to the moment of stable localization of deformation, are established. At the same time, it is recommended to replace the checked equipment nodes due to the exhaustion of the resource. The proposed and justified approach to assessing and predicting the performance and residual life of long-term power equipment, based on the identified relationships between the structural and substructural states, internal stress fields and stable localization of deformations with the characteristics of non-destructive tests and the calculation of the structural-mechanical criterion, was applied at a number of power plants in the Kemerovo region – Kuzbass. A methodology has been developed for evaluating the residual life, based on the identification and use of relationships between structural and substructural states, internal stress fields and stable localization of deformations with the characteristics of non-destructive tests and the calculation of a structural-mechanical criterion.

Background/Objectives: Successfully weaning patients with prolonged mechanical ventilation (PMV: ≥21 days) from ventilators is a challenging process, and proper nutritional support is a crucial factor in this process. Previous studies have highlighted the significance of higher albumin levels and increased daily protein intake in predicting successful weaning among PMV patients. However, the importance of calorie intake in patients with PMV has remained unclear. Methods: This retrospective study included 1,038 adult patients (age >18 years) who underwent endotracheal intubation or tracheostomy and required mechanical ventilation for >21 days. Baseline characteristics, nutritional variables, disease severity, management factors and patient outcomes (hospital stay and duration of ventilator use) were analyzed between the weaning-failure and weaning-success sub-cohorts and factors associated with successful weaning were identified. Results: The participants had mean APACHE II score of 18 and a Day 1 SOFA score of 4.9 and the successful weaning rate was 70%. Multivariate logistic regression analysis revealed that higher albumin and hemoglobin levels, the absence of shock, less positive fluid status, and higher calorie intake were associated with a higher successful weaning rate; an average calorie intake higher than 25 kcal/kg/day during respiratory care center (RCC) stay predicted better successful ventilator weaning. Conclusions: Higher daily calorie intake in the RCC is associated with more successful ventilator weaning, and an average intake exceeding 25 kcal/kg/day is recommended for optimizing the weaning process.

The utilization of biowaste fillers in the development of high-density polyurethane (PU) foams has gained significant attention due to environmental and economic benefits. This study investigates the mechanical properties of PU foams reinforced with biowaste fillers extracted from fish scales (FS) and fish scale derived collagen (FSC). The fish scales and collagen were characterized for their composition and integrated into PU foams at various loadings. Mechanical properties such as tensile strength, hardness, and density were evaluated. ANOVA was used to analyze the mean values. Bonferroni tests were used to identify differences between the filler materials (α=.05). The tensile strength increases with increase in filler content for both FS (59.48 Kpa) and FSC (65.43Kpa). No differences were observed between FS and FSC in tensile strength. Significance differences were observed between the FS and FSC in both hardness and density (p&lt;0.001). The results demonstrated that both fillers enhanced the mechanical properties of PU foams, with collagen-reinforced foams showing superior performance. This suggests that collagen and fish scales can be effective biowaste fillers for developing environmentally friendly PU foams with enhanced mechanical properties.

The hot pressing process for 100% coriander-based fiberboards was optimized using an induction RocTool system, which offers rapid mold heating and cooling. The fiberboards were made with deoiled press cake as a proteic binder and extrusion-refined straw as reinforcement. A Doehlert’s experimental design evaluated the influence of pressure (10-50 MPa), molding time (60-300 s), and mold temperature (155-205°C) on fiberboard properties, energy consumption, cost, and environmental impact. The results showed that the RocTool device allows better temperature control during shaping, resulting in exacerbated adhesive properties for proteins. Using the isoresponse curves, optimal hot pressing conditions were 35 MPa, 300 s, and 205°C, corresponding to a 40.6 MPa flexural strength. However, it was observed that to achieve a MDF-like fiberboard with minimal production cost, much less restrictive molding conditions were sufficient, i.e., 32.5 MPa, 170 s, and 160°C. The study revealed that maximum thermopressing conditions emitted 3.87 kg of CO2 eq., while conditions leading to the MDF-like board reduced emissions to 1.45 kg CO2 eq., resulting in a more environmentally-friendly material.

This study investigates the microstructural evolution and mechanical properties of steel subjected to high-temperature heat treatment, with a focus on the formation and effects of dark phase precipitates. High Temperature Confocal Laser Scanning Microscopy (HTCLSM) was employed to observe the in-situ changes in microstructure as the steel was heated from room temperature to 900°C. The observations revealed that dark phase precipitates, identified as chromium carbides (Cr7C3), began forming at approximately 820°C and increased in quantity and size up to 900°C. Scanning Electron Microscopy (SEM) and Energy-Dispersive X-ray Spectroscopy (EDX) confirmed that these precipitates significantly enhance the material's hardness, with microhardness values of 320 HV for the precipitates compared to 270 HV for the matrix. Tensile tests showed that the tensile strength of the steel increases with soaking time at 900°C, reaching a maximum after 3 minutes due to the strengthening effect of the precipitates. Beyond this point, strength decreases due to grain coarsening.

The cellular behavior of Voronoi tessellation has generated interest due to its applicability in various fields and its notable structural properties. Controlling factors such as the gradient of the cells, the position of seed points and the thickness of the arms allows for adjusting rigidity and flexibility according to specific needs. This article analyzes the state of the art of this technique, exploring its modification for applications in engineering and design, complemented with information on natural structural properties. This comprehensive analysis provides a complete overview of Voronoi tessellation and its potential in engineering and design, categorizing methodologies according to selected processing methods and highlighting techniques for altering structural behavior. Additionally, it emphasizes the integration of biomimetic approaches, connecting nature with technology to foster continuous innovation. Finally, the article addresses encountered limitations, offering future perspectives for the cellular technique and highlights the complexity of reproducibility due to reserved or generalized steps, despite the significant diversity in implemented techniques.

The effect of ceria doping of (ZrO2)1-x(Sm2O3)x crystals on their phase composition, microhardness and fracture toughness has been studied. The (ZrO2)0.995-х(Sm2O3)х(СеО2)0.005 crystals (where x = 0.032, 0.037 and 0.04) have been grown using directional melt crystallization in cold skull. The phase composition and structure of the crystals have been studied using X-ray diffraction, TEM and Raman spectroscopy. The mechanical properties such as microhardness and fracture toughness have been studied using Vickers indentation. It has been shown that the (ZrO2)0.995-х(Sm2O3)х(СеО2)0.005 solid solution crystals contain both Се4+ and Се3+ ions. Phase analysis data suggest that СеО2 doping increases the tetragonality degree of the transformable t phase and reduces the tetragonality degree of the non-transformable t' phase as compared to the (ZrO2)1-x(Sm2O3)x crystals. As a result, the t→m phase transition triggered by the indentation-induced stress in the СеО2 doped crystals is more intense and covers greater regions. СеО2 doping of the solid solutions increases the fracture toughness of all the crystals studied whereas the microhardness of the crystals changes but slightly. СеО2 doping of the (ZrO2)1-х(Sm2O3)х solid solutions in the experimental concentration range does not improve the high-temperature phase stability of the crystals and does not prevent high-temperature degradation of their fracture toughness.

The objective of this study is to develop a predictive model for low-carbon bainitic steel utilising the P and λ parameters. The tempering activation energy of the steel was calculated through statistical methods. Kinetic curves for the hardness equivalents and a nomograph for tempering process parameters were plotted. The error analysis indicates that the predicted values based on the λ and P parameters had errors within 15% and 10%, respectively. The model can be effectively utilised to predict mechanical properties and optimise parameters during the tempering process.

In this study, AlSi12 alloy was fabricated using the selective laser melting (SLM) technique to produce high density components with complex and customized parts for railway applications. Nonetheless, the production of dense samples necessitates the optimization of production process parameters. As a statistical design of experimental technique, the response surface methodology was used to optimise different combination of SLM parameters. The results were analysed using analyse of variance (ANOVA) and the signal-to-noise(S/N) ratios. The relationship between the hardness response to the process parameters (scanning speed and lase power) for determining the optimal processing conditions were examined. A hardness value of 133 HV was obtained. The process parameters were successfully optimized and the relationship between the parameters and the structures of the fabricated samples were reported.

Flexible electronics have revolutionized the field by overcoming the rigid limitations of traditional devices, offering superior flexibility and adaptability. Conductive ink performance is crucial, directly impacting the stability of flexible electronics. While metal filler-based inks exhibit excellent conductivity, they often lack mechanical stability. To address this challenge, we present a novel conductive ink utilizing a ternary composite filler system: liquid metal and two micron-sized silver morphologies (particles and flakes). We systematically investigated the influence of filler type, mass ratio, and sintering process parameters on the composite ink's conductivity and mechanical stability. Our results demonstrate that flexible wires fabricated with the liquid metal/micron silver particle/micron silver flake composite filler exhibit remarkable conductivity and exceptional bending stability. Interestingly, increasing the liquid metal content results in a trade-off, compromising conductivity while enhancing mechanical performance. After enduring 5000 bending cycles, the resistance change in wires formulated with a 4:1 mass ratio of micron silver particles to flakes is only half that of wires with a 1:1 ratio. This study further investigates the mechanism governing resistance variation during flexible wire bending. Additionally, we observed a positive correlation between sintering temperature and pressure with the conductivity of flexible wires. The significance of sintering parameters on conductivity follows a descending order: sintering temperature, sintering pressure, and sintering time. Finally, we demonstrate the practical application of this technology by integrating the composite ink-based flexible wires with conductive polymer-based strain sensors. This combination successfully achieved the detection of human movements, including finger and wrist bending.

Friction stir processing (FSP), a severe plastic deformation process, was applied on commercially pure Ti to obtain an improved microstructure. The process yielded a refined microstructure and higher mechanical properties at room temperature (RT). Yet the microstructure was found to contain bright bands demonstrating high hardness values of about 500 HV. High resolution scanning electron microscopy (HRSEM) as well as electron back scattering diffraction (EBSD) analysis indicated that these bands were composed of extra-fine equiaxed α-Ti grains with an average radius of 1-2 microns. In addition, a retained β-phase was detected at the boundaries of these α-Ti grains, together with a small quantity of separate β grains. The results of a fractography study conducted on broken tensile specimens showed that the FSP’ed material was free of defects and that the fracture started at these bands. It is proposed that these bright bands are due to excessive deformation occurring during the processing stage, leading to an accelerated dynamic recrystallization (DRX) process. In turn, these heavy deformation regions act as a strengthening constituent, making the material superior to the parent material as far as its mechanical RT properties are concerned. Consequently, this means that FSP of CP-Ti has the potential to serve as an industrial means of improving the mechanical properties of the material.

Citrus waste has been used as a source of bioplastic research in different ways. Because the juice industry produces significant amounts of residue each year, it would be advantageous to use the byproducts in the creation of new materials. For many years, researchers have been investigating an environmentally friendly way to take citrus and other organic waste and turn it into polymers that may be used, for instance, to produce bio-based and biodegradable films for food packaging. The goal of this study is to create biofilms from orange (OW) and ginger waste (GW) using an ultrafine grinder and study the films' properties. Since pectin has the ability to gel and because cellulosic fibres are strong, citrus waste has been studied for its potential to produce biofilms. After being washed, dried, and milled, orange and ginger waste were shaped into films using a casting process. Tensile testing was used to determine the mechanical properties of biofilms, while dynamic mechanical thermal analysis (DMTA), thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC) were used to determine their thermal properties. As the number of grinding cycles increased, the suspension's viscosity increased from 29 to 57 mPa.s for OW and from 217 to 376 mPa.s for GW while the particle size in the suspension significantly decreased. For OW and GW films, the highest tensile strength was 17 MPa and 15 MPa, respectively. The maximum strain obtained among all films was 4.8%. All the tested films were stable up to 150°C, and maximum degradation occurs after 300°C.

This study examines the effects of the δ phase and annealing twins on the hardness, Charpy impact toughness, and tensile properties of Inconel 718 fabricated using L-PBF. Two heat treatment methods, involving solid solution and precipitation hardening, were utilized. The δ phase was formed through solid solution heat treatment at 980C for 1 hour while annealing twins were generated at 1100C for 3 hours. After precipitation hardening, specimens with a higher concentration of  precipitates exhibited increased ultimate tensile strength (13%), yield strength (27%), and hardness (12%) compared to those with annealing twins. This can be attributed to the smaller grain size, subgrains, and δ precipitates, which contribute to the differences in mechanical strength. On the contrary, specimens with annealing twins showed significantly higher impact toughness (4 times) and ductility (twice) than those with δ precipitates. This is caused by the formation of  precipitates, which serve as sites for void formation and crack propagation, leading to a decrease in plasticity due to lattice mismatches with the matrix. Microstructural, compositional, phase, crystallographic, and fractographic analyzes were performed using OM, SEM, TEM and XRD techniques to identify the factors responsible for the variations in the measurements. The results demonstrate that the heat treatment method involving annealing twins significantly improves the ductility of Inconel 718 while maintaining the required mechanical strength.

In this paper thermo-mechanical behavior of 4D printed Polylactic Acid (PLA) was investigated, focusing on its response to varying strain rates and temperatures below the glass transition temperature. Dynamic mechanical analysis and uniaxial tensile tests confirmed PLA's dependency on strain rate, showcasing its sensitivity to external stimuli. Stress-strain curves exhibited typical thermoplastic behavior, with yield stresses varying with strain rates, underscoring PLA's responsiveness to different deformation speeds. Clear strain rate dependence was observed, particularly at quasi-static rates, with temperature and strain rate fluctuations significantly influencing PLA's mechanical properties, including yield stress and deformation behavior. Isothermal compression tests demonstrated predictable stress-strain curves with distinct yield points, while adiabatic tests reveal additional complexities such as heat accumulation leading to further softening. Thermal imaging revealed temperature increase during deformation, highlighting the material's thermo-sensitive nature. These findings provide the basis for future research with the focus on advanced modeling techniques and mitigation strategies for self-heating effects, aiming to enhance PLA-based product reliability and performance in applications with deformations at higher strain rates, while also developing models to simulate shape recovery in 4D printed PLA structures at both cold and hot programming temperatures.

Synthetic materials such as Carbon, Kevlar, and Glass fibers are extensively utilized in various industries due to their superior characteristics including high stiffness, great strength, low den-sity, and high wear resistance, these advantages contributed to making them widespread in ap-plications like; aerospace, automobile, civil and electronics. This research is carried out to enhance the creep compliance of epoxy composite material by considering two types of fibers as reinforcement. A composite material is produced by combining two fibers, Kevlar fiber mixed with sika epoxy resin, along with Carbon fiber also mixed with sika epoxy resin using a Hand-Layup process. Experiments and numerical modeling are examined to offer a comprehensive understanding creep behavior of epoxy composite material in different weight ratios. Burger and Prony models are used to represent stress relaxation and creep strain of Visco-elastic material. According to the results, sika epoxy resin reinforced with Kevlar and Carbon fibers exhibits enhancement in the mechanical properties compared with pure epoxy. The use of Kev-lar/Sika epoxy composite results in higher creep compliance and modulus of elasticity compared with Carbon/Sika epoxy composite.

The wood-based panel industry is experiencing an excessive accumulation of solid residues from the production of medium-density fiberboard (MDF) panels and moldings. It is possible to create new MDF products with acceptable physical and mechanical properties by revaluing MDF residues. Additionally, those products’ thermal properties can be improved by incorporating phase change materials (PCMs). This study aims to develop a wood-based fiberboard made of MDF residues, capable of storing thermal energy. Two types of PCMs, two PCM ratios, and two types of adhesives were used to produce eight different types of panels. The vertical density profile, thickness swelling, water absorption, internal bond (IB), and static bending properties – modulus of elasticity (MOE) and modulus of rupture (MOR) – were determined for each panel type. The specific heat of the panels was also determined. The results show the panels’ densities were greater than 700 kg/m3. Thickness swelling in water improved by 23% compared to the reference value of the control panel PCMs after PCM incorporation. The highest IB value was 1.30 MPa, which is almost three times the minimum required by regulation standards. The incorporation of PCMs reduced the panels’ bending properties compared to the properties of the control panels. Even though the values obtained are sufficient to comply with the minimum values set out in ANSI standard A208.2 with a MOE value of 2072.4 MPa and the values obtained are sufficient to comply with the minimum standards with a MOE value of 2072.4 MPa and a MOR value of 16.4 MPa. When microencapsulated PCM is used, the specific heat of the panels is increased by more than 100% over that of the control panels. This study develops a feasible alternative for using MDF residues: to create fiberboard that is capable of storing thermal energy and has adequate physical and mechanical properties.

In reinforced concrete (RC) structures, splicing is required owing to the length limitations of rebars, insufficient lengths, and transportation issues. In particular, splices connect the rebar of RC structures such as walls, columns, beams, slabs, and joints. Lap splices are the most commonly used method worldwide because they do not require specific equipment or skilled workers. However, lap splices incur high construction costs because of the long splice lengths required for large-diameter rebars in megastructures, as well as issues pertaining to material supply, labor costs, constructability, and project duration. Additionally, approximately 15% more rebar is required because of the overlap. Energy saving for a sustainable built environment is possible if the disadvantage of lap splices, which generate high CO2 emissions due to the excessive use of rebar, are resolved. Hence, mechanical rebar couplers (MRCs) have been developed. However, despite their advantages, they have not been widely applied in construction sites owing to concerns regarding safety, quality, and constructability. Although various MRCs have been developed, most studies focus only on their structural performance. Therefore, a data-driven approach for selecting MRCs based on the reinforcing bar shape and structural characteristics is proposed in this study. Using a data-driven MRC selection algorithm, using the T-threaded coupler for one rebar over two floors resulted in 56% more efficient labor productivity, 15% shorter assembly time, 17% lower costs, and 26% lower CO2 emission. Using a developed algorithm, the appropriate MRC can easily and rapidly be selected for frequent design changes.

Hydrogel wound dressings hold great potential in eliminating bacteria and accelerating the healing process. However, it remains a challenge to fabricate hydrogel wound dressings that simultaneously exhibit excellent mechanical and photothermal antibacterial properties. Here we report the development of polydopamine-functionalized graphene oxide/calcium alginate/Polypyrrole cotton fabric-reinforced hydrogels (abbreviated as rGO@PDA/CA/PPy FHs) for tackling bacterial infections. The mechanical properties of hydrogels were greatly enhanced by cotton fabric reinforcement and an interpenetrating structure, while excellent broad-spectrum photothermal antibacterial properties based on the photothermal effect were obtained by incorporating PPy and rGO@PDA. Results indicated that rGO@PDA/CA/PPy FHs exhibited superior tensile strength in both the warp (289±62.1N) and weft directions (142±23.0N) similar to cotton fabric. By incorporating PPy and rGO@PDA, the swelling ratio was significantly decreased from 673.5% to 236.6%, while photothermal conversion performance was significantly enhanced with a temperature elevated to 45.0 ℃. Due to the synergistic photothermal properties of rGO@PDA and PPy, rGO@PDA/CA/PPy FHs exhibited excellent bacteria-eliminating efficiency for S. aureus (0.57%) and E. coli (3.58%) after exposure to NIR for 20 min. We believe that the design of fabric-reinforced hydrogels could serve as a guideline for developing hydrogel wound dressings with improved mechanical properties and broad-spectrum photothermal antibacterial properties for infected wound treatment.

Hydrogels are three-dimensional crosslinked materials known for their ability to absorb water, exhibit high flexibility, biodegradability, biocompatibility, and mimic properties of different tissues in the body. However, their application is limited by inherent deficiencies in mechanical properties. To address this issue, reduced graphene oxide (rGO) and tannins (TA) were incorporated into alginate hydrogels (Alg) to evaluate the impact of the concentration of these nanomaterials on mechanical and adhesive, as well as cytotoxicity and wound healing properties. Tensile mechanical tests demonstrated improvements in tensile strength, elastic modulus, and toughness upon the incorporation of rGO and TA. Additionally, the inclusion of these materials allowed a greater energy dissipation during continuous charge-discharge cycles. However, the samples did not exhibit self-recovery under environmental conditions. Adhesion was evaluated on pig skin, revealing that higher concentrations of rGO led to enhanced adhesion, while the concentration of TA did not significantly affect this property. Moreover, adhesion remained consistent after 10 adhesion cycles, and contact time before the separation between the material and the surface did not affect this property. The materials were not cytotoxic and promoted healing in human fibroblast model cells. Thus, an Alg/rGO/TA hydrogel with enhanced mechanical, adhesive, and wound healing properties was successfully developed.

This study investigates the effects of Zinc (4wt.%) and severe plastic deformation on the mechanical properties of AZ61 magnesium alloy through the stir-casting process. The severe plastic deformation (equal channel angular pressing (ECAP)) has been done followed by T4 heat treatment. The microstructural examinations revealed that the addition of 4wt.%Zn enhances the uniform distribution of β-phase, contributing to a more uniformly corroded surface in corrosive environments. Additionally, dynamic recrystallization (DRX) significantly reduces the grain size of as-cast alloys after undergoing ECAP. The attained mechanical properties demonstrate that after a single ECAP pass, AZ61 + 4wt.%Zn alloy exhibits optimal yield strength (YS), ultimate compression strength (UCS), and hardness. This research highlights the promising potential of AZ61 + 4wt.%Zn alloy for enhanced mechanical and corrosion-resistant properties, offering valuable insights for applications in diverse engineering fields.

Polymer-based composites are widely used in the automotive, security, aeronautical and space industries, to mention a few. This is because of their good mechanical properties, which are similar to those of metals but with the attraction of being lightweight. Kevlar® as a reinforcement is extensively used in the security industry owing to its good ballistic properties. This investigation presents the mechanical characterization based on in-plane quasi-static tensile testing of Kevlar® composite using a universal testing system. The methodology developed for the preparation of coupons is based on pressure, temperature and time. As a result of this work, elastic moduli (EL and ET), Poisson’s ratio (νLT), shear modulus (GLT) and strengths (XT, YT, S) were obtained. It is worth mentioning that there is scarce or no characterization of this material in the literature, and those studies that do characterize it do not present the coupon thermoforming conditions or the reasons of the specimen dimensions (width, length and thickness).

The UN Sustainable Development Goal 7 Report 2022 is about ensuring access to clean and affordable energy, which is key to the development of agriculture, business, communications, education, healthcare, and transportation. The lack of access to energy hinders economic and human development. Nevertheless, the current pace of progress is insufficient to achieve Goal 7 by 2030. Huge disparities in access to modern sustainable energy persist. Rising commodity, energy and shipping prices have increased the cost of producing and transporting solar photovoltaics modules, wind turbines and biofuels worldwide, adding uncertainty to a development trajectory that is already far below Goal 7 ambitions. Achieving energy and climate goals will require continued policy support and a massive mobilization of public and private capital for clean and renewable energy such as methane from biomass. An important factor in improving methane yield from biomass waste is pre-treatment of the biomass prior to anaerobic digestion. Size reduction of lignocellulose biomass is important for changing and increasing digestibility thus increasing methane yield. A Hollander beater was used as the mechanical pre-treatment machine throughout this study. Results indicate that methane yield is directly proportional to feedstock/Inoculum (F/I) ratio as higher F/I ratio led to higher methane yield. It was observed at an F/I ratio of 0.5 that 5 minutes pre-treatment time produced highest methane yield, while the lowest methane yield was observed at an F/I ratio of 0.2 with 1 minute of pre-treatment time. Methane yield decreased by 30% from 140 mL gTS-1 at F/I ratio 0.5 with 5 minutes pre-treatment time to 98 mL gTS-1 at F/I 0.2 with 5 minutes pre-treatment time. The optimum methane yield was attained at high F/I ratio allowing sufficient nutrient essential for complete degradation of biomass. Overall, this research shows the Hollander beater is not efficient in optimizing methane yield for cardboard.

The paper concerns with the identification of current communication technologies and software functionalities from the field of digitalization and Industry 4.0, from the point of view of benefits and applicability for the machine manufacturer. In order to identify the relevant technologies and functionalities, both a descriptive and statistical literature research was carried out. As a result, both the currently most widespread technologies and eleven IT functionalities relevant to mechanical engineers were identified and described in terms of their application and implementation. In addition, a knowledge gap in the area of industry transfer in the field of Industry 4.0 / Digitalization was identified

In this study, seven mortar mixes were prepared by replacing natural sand by crumb rubber ,CR, (10%, 25%, 50%, 60%, 75% and 100%). The properties of mortars, both in their fresh and hardened states, were studied. Key characterisitcs, including density, water absorption coefficient, porosity, thermal conductivity, heat capacity, shrinkage/swelling, elastic modulus, compressive strength, flexure strength, fracture energy and performance after exposure to heat, were evaluated. The results obtained showed that as the CR fraction increased, density, initial setting time, and workability decreased but mortars with CR fractions ranged between 25% and 50% are lightweight and can be used for repairing as they fulfill satndards. It was observed that strengths and stiffness decreased with higher CR content while shrinkage increased for CR percentage higher than 60%. However, up to 50% of CR content the mortars obey to the standards for repair. Interestingly, incorporating up to 50% waste tires proved to improve comfort and thermal resistance without affecting thermal inertia. A slight increase in the mass loss is observed when mortars are exposed to high temperatures. Mortars containing CR between 25% and 50% can be classified as lightweight and thermally insulating mortars, suitable for repairing concrete structures in accordance with industry standards.

To improve the adaptability of aerial reflective opto-mechanical structures to low-temperature environments, an optimized thermal control design is proposed. Firstly, the relationship be-tween conventional heating methods and axial/radial temperature differences of mirrors with different shapes is analyzed. Based on heat transfer analyses, it is pointed out that optimized thermal control design is necessary to ensure the temperature uniformity of the fused silica mirror and take into account the temperature level when working in low temperature environ-ments. A thermal control scheme based on temperature negative feedback variable power zone heating is proposed for the characteristics of aerial electro-optics systems. Using the thermal control scheme at low temperatures ensures that the average temperature of the mirror fluctu-ates slowly and slightly around 20℃. At the same time, the temperature differences within a mirror and between the primary mirror and the secondary mirror can be controlled within 5℃. Thereby, satisfactory image quality is obtained.