This article presents a buck converter in which the inductor has been replaced by a transmission line. This approach would be practically conceivable if the power supply and load have a greater spatial distance. In the time domain, this new converter can be described by a system of coupled partial and ordinary differential equations. In the frequency domain, a transcendental transfer function is obtained. For comparison with an equivalently parameterized conventional converter, Padé approximants are derived. A linear controller is designed for the converter topology under consideration.

In this research paper, a novel high step up dc-dc converter with a coupled inductor and voltage doubler circuits is proposed. The converter achieves a high step up voltage gain with an appropriate duty ratio and low voltage stress on the power switches. Also, the energy which is stored in the leakage inductor of the coupled inductor can be recycled to the output. The operating principles and the steady state analysis of the proposed converter are discussed in detail. Finally, a prototype circuit of the proposed converter is implemented in the laboratory in order to verify the performance of the proposed converter.

To improve the voltage gain of step-up converters, cascaded technique is considered as a possible solution in this paper. By considering the concept of cascading two Z-source networks in a conventional boost converter, the converter takes the advantages of both impedance source and cascaded converters. However, by applying some modifications, the proposed converter provides high voltage gain while the voltage stress of switch and diodes are still low. Moreover, the low input current ripple of the converter makes it absolutely appropriate for photovoltaic applications in order to expand the lifetime of PV panels. After analyzing the operation principles of the proposed converter, simulation and experimental results of a 100W prototype are presented to verify the proposed converter performance.

This paper proposes a novel symmetrical active-switched coupled-inductor high-step-up DC/DC converter. A new active-switched coupled inductor is used to allow much higher voltage gain of the proposed converter. The symmetrical circuit structure of the proposed converter evenly divides large input currents and reduce input current ripple by operating in interleaved mode so power density is increased. The switches also have low voltage stress. The operating principle and design considerations for the converter topology are described. The proposed converter with an input voltage of 40 V, an output voltage of 400 V and an output of 1000 W at a switching frequency of 50 kHz is implemented. The simulations and experimental results are thus depicted to verify the theoretical analysis. The highest efficiency is 95.5% at 200 W measured by using a HIOKI 3390. Consequently, the proposed converter is suitable for renewable energy generation systems that require high power, high voltage gain and high efficiency.

This paper presents a new high-efficiency-high-step-up based converter integrating two stype DC-DC Boost and Flyback coupled magnetic converter with recovery stage dedicated to smart HVDC distributed architecture in renewable energy production systems. Appropriate duty cycle ratio assumes that the recovery stage work with parallel charge and discharge to achieve high step-up voltage gain. Besides, the voltage stress on the main switch is reduced with a passive clamp circuit and thus, low on-state resistance Rdson of the main switch can be adopted to reduce conduction losses. The circuit is simple to control. As a final point of this research, the simulation and the prototype investigational results are presented to demonstrate the effectiveness of this proposed converter.

This article presents a self balanced multistage DC-DC step-up converter for photovoltaic applications. Proposed converter topology is designed for unidirectional power transfer and provides a doable solution for photovoltaic applications where voltage is required to be stepped up without magnetic components (Transformer-less and Inductor-less). The output voltage obtained from renewable sources will be low and must be stepped up by using a DC-DC converter for photovoltaic applications. K diodes and K capacitors along with two semiconductor control switch are used in the K-stage proposed converter to obtain an output voltage which is (K+1) times the input voltage. The conspicuous features of proposed topology are i) Magnetic components free (Transformer-less and Inductor-less). ii) Continuous input current iii) Low voltage rating semiconductor devices and capacitors iv) Modularity v) Easy to add a higher number of levels to increase voltage gain vi) Only two control switches with alternating operation and simple control. The proposed converter is compared with recent existing transformer-less and Inductor-less power converter in term of voltage gain, number of devices and cost. The application of proposed circuit is discussed in detail. The proposed converter has been designed with rated power of 60W, input voltage is 24V, output voltage is 100V and switching frequency is 100 kHz. The performance of the converter is verified through experimental and simulation results.

Down Syndrome (DS) is a chromosomal disorder due to the presence of an additional chromosome 21 that causes intellectual deficit and physical anomalies and predisposes patients to develop infections throughout their lives. Pneumonias are more serious in patients with DS, requiring hospitalization, and represent an important cause of mortality in this population. Cytomegalovirus (CMV) causes widespread and serious infections in immunocompromised individuals, affecting the respiratory tract and, causing interstitial pneumonia, is associated with a high mortality rate. However, CMV-induced pneumonia is not reported in DS patients. The prevalence and severity of CMV respiratory infections in subjects with DS is unknown. This case describes a 50-year-old female patient suffering from DS who developed extensive bilateral pneumonia with severe respiratory failure which required hospitalization in intensive care, intubation and mechanical ventilation after approximately 10 days of empiric antibiotic and anitimycotic therapy for fever, cough and dyspnea. The patient was diagnosed with CMV pneumonia and recovered after treatment with Ganciclovir. To the best of our knowledge, this is the first reported case of CMV pneumonia in a patient with DS. This case aims to highlight that CMV pneumonia in individuals with DS can be a life-threatening condition. It also clarifies the importance of early diagnosis of infections from opportunistic pathogens such as CMV to ensure timely and efficient treatment.

Running on a non-motorized, curved-deck treadmill is thought to improve gait mechanics. It is not known, though, if the change in gait carries over to running on a motorized treadmill or level ground. To determine the effect of running on a curved non-motorized treadmill (CNT) on gait characteristics measured during a subsequent bout of running on a traditional motorized treadmill (TMT). Sixteen healthy college-aged participants, age (mean±SD) 20.4±1.6 years volunteered to have their gait analyzed while running on a TMT and CNT. After familiarization and warm-up on both treadmills, each subject completed five, 4-minute bouts of running alternating between traditional motorized and curved non-motorized treadmills: TMT-1, CNT-1, TMT-2, CNT-2, and TMT-3. Variables of interest included step length (m), stride length (m), imbalance score (%), and step angle (°) and were measured using Optogait gait analysis equipment. Differences in gait char acteristics among TMT-1, TMT-2, and TMT-3 can be attributed to running on the CNT. The results show that running on a CNT resulted in significant changes in gait characteristics. These findings suggest that running on a CNT can significantly alter gait characteristics may result in improvements in running gait that persist to subsequent running on a TMT.

The combined use of lasmiditan and triptan is unexplored in medical literature. This study aimed to investigate whether the intake of lasmiditan following triptan improves migraine pain. Following triptan intake, if headache relief was less than 50% at 1 hour, patients took 50 mg lasmiditan within 2 hours of migraine onset. Patients recorded headache intensity and adverse events(AEs) caused by lasmiditan at 1, 2, and 4 hours after intake of additional 50 mg of lasmiditan. A significant reduction in pain scale was observed post 50 mg lasmiditan intake (p < 0.001, t-test). Pain relief was reported for 32 migraine attacks (80%) at 1 hour after additional lasmiditan intake. Although AEs were observed in 63% of the patients who took an additional lasmiditan, most were mild and resolved 1 hour after lasmiditan intake. Our study revealed the significant headache reliefs provided by an additional lasmiditan for patients who did not achieve satisfactory results following initial triptan intake for treating migraine. The AEs associated with this treatment strategy were mild and lasted for a short term. This study suggested that the combination of triptan and lasmiditan is promising for the treatment of migraine and should be studied in a randomized placebo-controlled trial.

Research on microglia in Down syndrome (DS) has shown that microglial activation, increased inflammatory gene expression, and oxidative stress occur at different ages in DS brains. However, most studies resulted in simplistic definitions of microglia as quiescent or active, ignoring potential intermediate states. However, a recent work on microglial cells in young DS brains indicated that those evolve through different intermediate activation phenotypes before reaching a full activated state. Here we used single nucleus RNA sequencing, to examine how trisomy affects microglial states in the Ts65Dn mouse model of DS. Despite no substantial changes in the proportion of glial populations, differential expression analysis revealed cell type-specific gene expression changes, most notably in astroglia, microglia, and oligodendroglia. Focusing on microglia, we identified differential expression of genes associated with different microglial states, including disease-associated microglia (DAMs), activated response microglia (ARMs), and human Alzheimer’s disease microglia (HAMs), in trisomic microglia. Furthermore, pseudotime analysis reveals a unique reactivity profile in Ts65Dn microglia, with fewer in a homeostatic state and more in an intermediate aberrantly reactive state than in euploid microglia. This comprehensive understanding of microglial transcriptional dynamics sheds light on potential pathogenetic mechanisms but also possible avenues for therapy for neurodevelopmental disorders.

Abstract: Down Syndrome (DS) is a common genetic disorder characterized by an extra copy of chromosome 21, leading to dysregulation of various metabolic pathways. Oxidative stress in DS is associated with neurodevelopmental defects, neuronal dysfunction, and the onset of dementia re-sembling Alzheimer's disease. Additionally, chronic oxidative stress contributes to cardiovascular diseases and certain cancers prevalent in DS individuals. This study investigates the impact of ageing on oxidative stress and liver fibrosis using a DS murine model (Ts2Cje mice). The liver in DS mice shows increased oxidative stress and impaired antioxidant defenses, as evidenced by reduced glutathione levels and increased lipid peroxidation. Furthermore, DS liver exhibits an altered in-flammatory response as measured by the expression of cytokines and heat shock proteins. DS liver also displays dysregulated lipid metabolism, indicated by altered expression of peroxisome prolif-erator-activated receptors and fatty acid transport proteins. Consistently, these changes might contribute to non-alcoholic fatty liver disease development, a condition characterized by liver fat accumulation. Finally, histological analysis of DS liver reveals increased fibrosis and steatosis, in-dicative of potential progression to liver cirrhosis. This finding highlights the increased risk of liver pathologies in DS individuals, particularly when combined with the higher prevalence of obesity and metabolic dysfunctions in DS patients. These results shed light on the liver's role in DS-associated pathologies and suggest potential therapeutic strategies targeting oxidative stress and lipid metabolism to prevent or mitigate liver-related complications in DS individuals.

Monitoring the quality of stored bulk grain is generally done using temperature cables hung from silo roofs. Little investigation has been done into the effects of number of sensors and their placement in terms of reliability of the monitoring system with regard to making stored grain quality management decisions. A previously developed 3D finite element simulation model was verified and used to investigate these aspects. In the first study, a silo was loaded with about 228.6 Mg (9000 bushels) of maize and six temperature cables were placed in the grain mass. The maize was aerated continuously for a period of two weeks, and the cable sensor temperatures were compared to the predicted temperatures which were in close agreement with the observed readings. The standard error of prediction ranged from 2.0 to 3.7°C. In the second study, 15 and 30 sensors were placed at manufacturer recommended depths and horizontal locations in the grain mass of three silo sizes (i.e., 11x11, 14.6x14.6 and 14.6x18.3 m diameter by eave height). The average grain temperatures predicted by the 15 and 30 sensors over a one-year simulation period were compared to the average grain temperatures predicted for the entire grain mass (1968, 3052, and 3204 mesh nodes). The number of sensors needed to monitor stored grain temperatures reliably in the three silo sizes investigated heavily depended on whether the aeration control strategy achieved a sufficiently low temperature by the time the aeration fans were turned off and sealed ahead of the non-aerated storage period. Fifteen or 30 sensors were sufficient to monitor grain temperatures during the aeration cooling period but for the two larger silo sizes more than 30 sensors would be needed during the storage period. As silo size increased, and surface-to-volume ratio decreased, grain temperatures remained lower during the storage period. Results support the best management practice recommendation of leaving cooled grain cold and not warming it up in the spring ahead of storage into the summer.

People with Down syndrome present cognitive difficulties that affect their reading skills. In this study we present results about the use of gestural interaction with Kinect sensor to improve the reading skills of students with Down syndrome. Following a case of study method for small samples with disabilities, measuring different variables related to reading skills in an experimental group and in a control group. We found improvements in the visual association, visual comprehension, sequential memory, and visual integration after this stimulation in the experimental group compared to the control group. Also, we found that the number of error and delay time of interaction decrease between sessions in the experimental group.

Richard Peto’s Paradox, first described in 1975 from an epidemiological perspective, established an inverse correlation between the probability of developing cancer in multicellular organisms and the number of cells. Larger animals exhibit fewer tumors compared to smaller ones, though exceptions exist. Mice are more susceptible to cancer than humans, while elephants and whales demonstrate significantly lower cancer prevalence rates than humans. How nature and evolution have addressed the issue of cancer in the animal kingdom remains largely unexplored. In the field of medicine, much attention has been devoted to cancer predisposing genes, as they offer avenues for intervention, including blocking, downregulating, early diagnosis, and targeted treatment. Predisposing genes also tend to manifest clinically earlier and more aggressively, making them easier to identify. However, despite significant strides in modern medicine, the role of protective genes lags behind. Identifying genes with a mild predisposing effect poses a significant challenge. Consequently, comprehending the protective function conferred by genes becomes even more elusive, and their very existence is subject to questioning. While the role of variable expressivity and penetrance defects of the same variant in a family is well-documented for many hereditary cancer syndromes, attempts to delineate the function of protective/modifier alleles have been restricted to a few instances. In this review, we endeavor to elucidate the role of protective genes observed in the animal kingdom and within certain genetic syndromes that appear to act as cancer-resistant/repressor alleles. The ultimate goal is to discern why individuals, like Winston Churchill, managed to live up to 91 years of age, despite engaging in minimal physical activity, consuming large quantities of alcohol daily, and not abstaining from smoking.

We have recently presented a unified quantum gravity theory [1]. Here we extend on that work and present an even simpler version of that theory. For about hundred years, modern physics has not been able to build a bridge between quantum mechanics and gravity. However, a solution may be found here; we present our quantum gravity theory, which is rooted in indivisible particles where matter and gravity are related to collisions and can be described by collision space-time. In this paper, we also show that we can formulate a quantum wave equation rooted in collision space-time, which is equivalent to mass and energy.The beauty of our theory is that most of the main equations that currently exist in physics are not changed (in terms of predictions), except at the Planck scale. The Planck scale is directly linked to gravity and gravity is, surprisingly, actually a Lorentz symmetry as well as a form of Heisenberg uncertainty break down at the Planck scale. Our theory gives a dramatic simplification of many physics formulas without altering the output predictions. The relativistic wave equation, the relativistic energy momentum relation, and Minkowski space can all be represented by simpler equations when we understand mass at a deeper level. This not attained at a cost, but rather a reflection of the benefit in having gravity and electromagnetism unified under the same theory.

Background: People with Down syndrome (DS) have a trisomy of chromosome 21 and marked deficits in verbal memory but relatively preserved visuospatial perception. Verbal memories are related to semantic knowledge. Little is known about the organization of semantic knowledge in people with DS, which was the aim of this study. Aims: The extent of false memory in people with DS was examined. Possible differences in the number of false memories induced by nominal and verbal themes were examined. Methods and Procedures: In the study phase, ten word lists with semantically related associates were presented. In the recognition phase, participants made judgments on whether each word had been represented previously as semantically related lures, old words, and semantically unrelated new words. Outcomes and Results: Differences in the processing of nominal and verbal theme-related lures were observed among people with DS. When processing nominal theme-related lures, people with DS showed delayed false positives. When processing verbal theme-related lures, people with DS showed no differences compared to controls. Similar patterns have been observed in people with DS when processing nominal theme-related associates and verbal theme-related associates. People with DS have delayed recognition of associates. When processing unrelated words, they showed significantly higher false positives than controls for both nominal and verbal eliciting themes. Further analyses of the themes revealed differences in false positives across syntactic categories among groups. Conclusions and Implications: People with DS showed a delayed recognition of associates and deviance in recognizing unrelated words in the nominal and verbal theme categories. People with DS were delayed in terms of nouns, but deviated with verbs in associated and unrelated words. Additionally, people with DS showed distinct patterns in processing five nominal lures and three verbal lures, suggesting that they formed false memories differently based on distinct syntactic categories. Thus, it was concluded that people with DS develop a deviant semantic structure. Category-based interventions for people with DS should be implemented in order to improve their semantic knowledge through lexical connections.

In this review we extensively describe the main post-translational modifications that give rise to the multiple proteoforms characterized to date in the human salivary proteome and their potential role. Most of the data reported were obtained by our group in over twenty-five years of research carried out on human saliva mainly by applying a top-down strategy. At the beginning we describe the products generated by proteolytic cleavages, which can occur before and after secretion. In this section the most relevant families of salivary proteins are also described. Next, we report the current information concerning the human salivary phospho-proteome and the limited news available on sulfo-proteome. Three sections are dedicated to the description of the glycation and enzymatic glycosylation. Citrullination and N- and C- terminal PTMs and a miscellaneous of other modifications are described in the last two sections. Results highlighting the variation in the level of some proteoforms in local or systemic pathologies are also reviewed along the sections of manuscript to underline the impact and relevance of this information for the development of new diagnostic biomarkers useful in clinical practice.

Down syndrome (DS) is a leading human genomic abnormality resulting from the trisomy of chromosome 21. The genomic base of the aneuploidy behind this disease is complex, and this complexity poses formidable challenges to understanding the underlying molecular basis. In the spectrum of the classic DS risk factor associations the role of nutrients, vitamins, and in general, the foodborne associated background as part of the events leading ultimately to chromosome nondisjunction has long been recognized as a well-established clinical association. The integrity of the microbiome is a basic condition in these events, and the dysbiosis may be associated with secondary health outcomes, the possible association of DS development with maternal gut microbiota should require more attention. We have hypothesized that different classes of antibiotics might promote or inhibit the proliferation of different microbial taxa and hence, we might find associations between the use of different classes of antibiotics and the prevalence of DS through the modification of the microbiome. As antibiotics are considered major disruptors of the microbiome, it could be hypothesized that the consumption/exposure of certain classes of antibiotics might be associated with the prevalence of DS in European countries (N=30). Utilizing three different statistical methods, comparisons have been made between the average yearly antibiotic consumption (1997-2020) and the prevalence of people living with DS estimated for 2019 as a percentage of the population in European countries. We have found strong statistical correlations between the consumption of tetracycline (J01A) and the narrow-spectrum, beta-lactamase-resistant penicillin (J01CF) and the prevalence of DS.

This paper aims to determine the insecticidal activity of Panyawan (Tinospora rumphii) leaf extract against American cockroach (Periplaneta americana). A quantitative experimental research design was employed in the study. Cockroach strains were collected through trapping and hand catch methods. Panyawan leaf was collected and extracted to achieve seven different concentrations. The concentrations and controls were tested against the strains through the standard contact glass jar bioassay. Results revealed that the shortest knock-down time was achieved by the positive control at 1.08 minutes while the Extracts of Panyawan leaf reported a 1.42 to 20.25 minutes knock-down time. Probit Regression reported that the lethal concentration 50 of Panyawan leaf extract was 15.836%. One-Way ANOVA revealed that there is a significant difference in the knock-down times of cockroaches when exposed to different Panyawan leaf extract concentrations, negative and positive controls (p<0.01). Homogeneous subsets derived from Post Hoc Test using Tukey’s Honest Significant Difference reported that there is no significant difference between positive control and Extract 100% (p>0.01).

Failure of wind turbines is a multi-faceted problem and its monetary impact is often unpredicted. In this study, we present a novel application of survival analysis on wind turbine reliability performance that includes accounting of previous failures and history of scheduled maintenance. We investigate the operational, climatic and geographical factors which affect wind turbine failures and model the risk rate of wind turbine failures based on data from 109 turbines in Germany operating during a period of 19 years. Our analysis showed that adequately scheduled maintenance can increase the survivorship of wind turbine systems and electric subsystems up to 2.8 and 3.8 times, respectively compared to the ones without scheduled maintenance. Geared-drive wind turbines and their electrical systems were observed to have 1.2- and 1.4-times higher survivorship, respectively, compared to direct-drive turbines and their electrical systems. It is also found that survivorship of frequently-failed wind turbine components, such as switches, is worse in geared-drive than in direct-drive wind turbines. We show that survival analysis is a useful tool for guiding the reduction of operating and maintenance costs of wind turbines.

Cochlear implantation is the therapy used for patients with severe to profound sensorineural hearing loss. For the success of the surgery, it is important that each surgical step is performed with meticulous precision, starting from the correct patient’s position on the operating table. In elderly or obese patients, this can be difficult to achieve due to cervical rigidity. In these cases, the orthopedic position is an excellent choice to perform a mastoidectomy accurately, ensuring a safe procedure and avoiding unpleasant complications.

The paper describes problems with the current additive manufacturing chain before considering additive manufacturing as part of a modern manufacturing chain. Additive manufacturing can be used for near net-shape for finishing, for repair or for adding special features which cannot be made with traditional manufacturing. This paper describes how STEP-NC deals with these different scenarios in terms of accuracy, multi-material and variation of slice direction. The possibilities of multi-material objects also raises questions about the design of such objects and how these need to be handled by an advanced controller. The paper also describes non-planar slicing. Curved direction and cylindrical direction are shown to improve the accuracy of curved structure additive manufacturing. STEP-NC using boundary representation has better capability of depicting complex internal structures for additive processes. By using exact model of the final product represented by STEP-NC, the paper demonstrates improvements in data size reduction, slicing accuracy, and precise manipulation of internal structure.

Graphene oxide was synthesized by a one-step environmentally friendly mechanochemistry process directly from graphite and characterized by Raman, FT-IR and UV/vis spectroscopies, Atomic Force Microscopy, X-ray Diffraction, Scanning Electron Microscopy, Energy-Dispersive X-ray Spectroscopy and Thermogravimetric Analysis. Spectroscopic analysis shows that the functional groups and oxygen content of the synthesized material are comparable with those of graphene oxide synthesized by other previously reported methods (Hummers). Thermogravimetric analysis reveals thermal stability up to 400 °C.

Background: Down Syndrome is the most well-studied aneuploidy condition in humans. It is associated with multiple disease phenotypes including cardiovascular, neurological, haemato-logical, and immunological disease processes. In this review paper we aim to discuss the research into gene expression studies performed at the fetal stage of development. Methods: A descriptive review was performed including all papers published on the PubMed database between Septem-ber 1960- September 2022. Results: In the amniotic fluid, genes such as COL6A1 and DSCR1 are affected, causing the phenotypical craniofacial changes. Other genes affected in amniotic fluid in-cluding: GSTT1, CLIC6, ITGB2, C21orf67, C21orf86 and RUNX1. In the placenta, MEST, SNF1LK and LOX were dysregulated, affecting nervous system development. In the brain DYRK1A, DNMT3L, DNMT3B, TBX1, olig2 and AQP4 were found to be dysregulated, affecting the nervous system and intellectual disability. In the cardiac tissues GART, EST2 and ERG found to be dysregulated causing secondary heart field abnormalities. XIST, RUNX1, SON, ERG and STAT1 dysregulated causing myeloproliferative disorders. Conclusions: Differential expression of genes provides clues to the genetic consequences of DS. A better understanding of these processes could eventually to lead to the development of genetic and pharmacological therapies.

People with Down syndrome have more visual problems than general population. They experience a premature aging, and it would be expected they will also have an acceleration in worsening visual function. A prospective observational study which includes visual acuity, refractive error, accommodation, binocular and colour vision was performed to young adults with (n=69) and without (n=65) Down syndrome and to a senior group (n=55) without Down syndrome. Results showed significant differences in visual acuity between groups (p&lt;0.001) and it can be improved with a new prescription in 40% of the participants with Down syndrome. Regarding to accommodative state, no significant differences were found between groups of young people. Concerning binocular vision, 64.7% of strabismus was observed in the group with Down syndrome (p&lt;0.001). Visual abnormalities are significant in young adults with Down syndrome and are different from those of older people without Down syndrome, some of which can be improved by providing the optimal prescription as well as regular eye examinations.

In this work, we compiled our research on lanthanide-based luminescent materials, prepared down-shifter layers, and studied their effect on photovoltaic (PV) mini-modules. The compounds we have prepared (C1-C17), with formulas [Eu2(phen)2(bz)6] (C1), [Eu2(bphen)2(bz)6] (C2), [Eu(tta)3bphen] (C3), [Eu(bta)3pyz-phen] (C4), [Eu(tta)3pyz-phen] (C5), [Eu(bta)3me-phen] (C6), [Er(bta)3me-phen] (C7), [Yb(bta)3me-phen] (C8), [Gd(bta)3me-phen] (C9), [Yb(bta)3pyz-phen] (C10), [Er(tta)3pyz-phen] (C11), [Eu2(bz)4(tta)2(phen)2] (C12), [Gd2(bz)4(tta)2(phen)2] (C13), [EuTb(bz)4(tta)2(phen)2] (C14), [EuGd(bz)4(tta)2(phen)2] (C15), [Eu1.2Gd0.8(bz)4(tta)2(phen)2] (C16) and [Eu1.6Gd0.4(bz)4(tta)2(phen)2] (C17), can be grouped into three families based on their composition: Series C1–6 were synthesized using Eu3+ ions and phenanthroline derivatives as the neutral ligands, and fluorinated β-diketonates as the anionic ligands. Complexes C7–11 were prepared with ligands similar to those of compounds C1–6 but were synthesized with Er3+, Yb3+, or Gd3+ ions. Series C12–17 exhibit the general formula [M1M2(bz)4(tta)2(phen)2], where M1 and M2 can be Eu3+, Gd3+, or Tb3+ ions, and the ligands are benzoate (bz–), 2-thenoyltrifluoroacetone (tta–) and 1,10–phenanthroline (phen). All compounds were characterized using X-ray techniques, and their photoluminescent properties were studied. We then examined their impact on the EQE (External Quantum Efficiency) of PV mini-modules and their durability in a climate chamber when embedded in PMMA and EVA films. This review emphasizes the methodology employed and the key findings, including enhanced mini-module efficiency. Additionally, we present promising results on the application of compound C6 in a bifacial solar cell.

Wildlife conservation is an important component of environmental sustainability and can be improved by reviewing the performance of its three major models – common pool, top-down regulatory, and private resource -- under varying environmental and socioeconomic conditions. Generally, the private resource model is the most sustainable because it provides the best incentives to balance the needs of humans and wildlife, to maintain general wildlife habitat, and to adapt quickly to changing environmental and/or socioeconomic conditions. Top-down or “command and control” regulation, however, can be employed as a model of last resort if the private resource model shows signs of failing to protect specific species from local extirpation or extinction, which it is most likely to do for migratory species, species with close commercial substitutes, and species with no direct commercial value. Top-down regulators may also be needed to enforce property rights arrangements like catch shares and to monitor resources that remain in the common pool in the event that socioeconomic or environmental conditions change sufficiently to trigger the tragedy of the commons.

Protein translational modifications (PTMs) generate an enormous, but as yet undetermined, expansion of the expressed proteoforms. In this Viewpoint, we firstly differentiate the concepts of proteoform and peptidoform by reviewing and discussing previous literature. We show that the current PTM biological investigation and annotation largely follow a PTM site-specific rather than proteoform-specific approach. We further illustrate a potentially useful matching strategy in which a particular “modified peptidoform” is matched to the corresponding “unmodified peptidoform” as a reference for the quantitative analysis between samples and conditions. We suggest this strategy could provide directly relevant information for learning the PTM site-specific biological functions. Accordingly, we advocate for the wider use of the nomenclature “peptidoform” in the future bottom-up proteomic studies.

Neurodevelopmental disorders arise from genetic and/or from environmental factors and are characterized by different degrees of intellectual disability. The mechanisms that govern important processes sustaining learning and memory, which are severely affected in intellectual disability, have classically been thought to be exclusively under neuronal control. However, this vision has recently evolved into a more integrative conception, in which astroglia, rather than just acting as metabolic supply and structural anchoring for neurons, interact at distinct levels modulating neuronal communication and possibly also cognitive processes. Recently, genetic tools have made it possible to specifically manipulate astrocyte activity unraveling novel functions that involve astrocytes in memory function in the healthy brain. However, astrocyte manipulation has also underscored potential mechanisms by which dysfunctional astrocytes could contribute to memory deficits in several neurodevelopmental disorders revealing new pathogenic mechanisms in intellectual disability. Here, we review the current knowledge about astrocyte dysfunction that might contribute to learning and memory impairment in neurodevelopmental disorders, with special focus on Fragile X syndrome and Down syndrome.

Recent progress in the fabricating flexible electronics has been developed significantly due to the increased interest of the flexible electronics which can be applied to enormous fields not only to conventional electronic devices but to bio/eco electronic devices. Flexible electronics can be applied to wide range of fields such as flexible display, flexible power storage, flexible solar cells, wearable electronics and healthcare monitoring devices. Recently, flexible electronics are being attached on the skin and even implanted into human body to monitor the bio-signals and for treatment purpose. To improve the electrical characteristic and the mechanical properties of flexible electronics, nanoscale fabrications using novel nano-materials are required. Advanced in nanoscale fabrication methods allow construction of the active materials that can combine with the ultra-thin soft substrate to form flexible electronics with high performances and reliability. In this review, wide range of nanoscale fabrication methods for flexible electronics classified in either top-down or bottom-up approaches such as conventional photolithography, soft lithography, nanoimprint lithography, growth, assembly and chemical vapor deposition(CVD) will be reported with specific fabrication processes and results. Here, our aim is to introduce various fabrication methods that can be used to fabricate the flexible electronics.

Background/Objectives: Population aging is rapidly increasing, and the importance of preventive medicine has been stressed. Health checkup, diet, and exercise are of paramount importance. This study aimed to evaluate the effectiveness of a personalized dual-task intervention that combined exercise with cognitive tasks in improving physical and cognitive functions among independently living elderly individuals. Methods: Participants were aged &gt;65 years who were mostly independent in their activities of daily living, divided into 2 groups. The group receiving the 20-min robot-assisted session was compared to the group receiving traditional functional restoration training. This randomized trial assessed the impact of this intervention on the 30-s chair stand test score and Montreal Cognitive Assessment-Japanese version score of the participants. Results: Both scores significantly improved in the intervention group, indicating enhanced lower-limb function and cognitive capabilities. Conclusions: These findings suggest that integrating cognitive tasks with physical exercise can be a potent strategy to improve overall well-being in the elderly, offering valuable insights for designing comprehensive preventive health programs tailored to this demographic.

In this paper, an analytical form of the Unit Step Function (or Heaviside Step function) is presented. This important function constitutes a fundamental concept of Operational Calculus and is also involved in many other fields of applied and engineering mathematics. In particular, Heaviside Step Function is performed in a very simple manner by the use of a finite number of standard operations, as the summation of six inverse tangent functions. The novelty of this work when compared with other analytical expressions, is that the proposed exact formula contains two arbitrary single - valued continuous functions which satisfy only one restriction. In addition, the proposed representation is not exhibited in terms of miscellaneous special functions, e.g. Bessel functions, Beta function, Logistic function. Besides, it is neither the limit of a function, nor the limit of a sequence of functions with point – wise or uniform convergence. Hence, this formula may be much more practical, flexible and useful in the computational procedures which are inserted into Operational Calculus techniques and other engineering practices.

The quest for accurate and more efficient methods for solving periodic/oscillatory problems is gaining more attention in recent time. This paper presents the construction and implementation of a family of exponentially–fitted Obrechkoff methods. A single–step Obrechkoff method involving terms up to the fourth derivatives was used as the base method. We also present the stability and convergence properties of the constructed family of methods. Two numerical examples were use to illustrate the performance of the constructed methods.

Multi-step ahead streamflow forecasting is of practical interest for the operation of hydropower reservoirs. We provide generalized results on the error evolution in multi-step ahead forecasting by conducting several large-scale experiments based on simulations. We also present a multiple-case study using monthly time series of streamflow. Our findings suggest that some forecasting methods are more useful than others. However, the errors computed at each time step of a forecast horizon within a specific case study strongly depend on the case examined and can be either small or large, regardless of the forecasting method used and the time step of interest.

Several recent epidemiological studies attempted to identify risk factors for Alzheimer's disease. Age, family history, genetic factors (APOE genotype, Down syndrome), physical activity, and a low level of schooling are significant risk factors. In this review, we summarize the known psychosocial risk factors for the development of Alzheimer's disease in Down syndrome patients and their association with neuroanatomical changes in the brains of people with Down syndrome. We completed a comprehensive review of the literature on PubMed, Google Scholar, and Web of Science about psychosocial risk factors for Alzheimer's disease, for Alzheimer's disease in Down syndrome, and Alzheimer's disease in Down syndrome and their association with neuroanatomical changes in the brains of people with Down syndrome. Alzheimer's disease causes early pathological changes in Down syndrome patients, especially in the hippocampus and corpus callosum. The field needs more data about the neuroanatomical changes during childhood, how they change with increasing age, and the presence or absence of psychosocial risk factors. Further neuroimaging and psychosocial assessment-focused research is needed to understand the mechanisms leading to Alzheimer's disease at an early age and create more sensitive and relevant clinical, memory, and reasoning assessments for people with Down syndrome.

In this paper, a new full-Newton step feasible interior point method for convex quadratic programming is presented and analyzed. The idea behind this method is to replace the complementarity condition with a non-negative variable weight vector and use the algebraic equivalent transformation for the obtained equation. Under the selection of appropriate parameters, the quadratic rate of convergence of the new algorithm is established. In addition, the iteration complexity of the algorithm is obtained. Finally, some numerical results are presented to demonstrate the practical performance of the proposed algorithm.

In this nano era, nanomaterials and nanostructures are popular in developing novel functional materials. However, the combinations of nanoproducts with materials at micro and macro scale can open new routes for conceiving novel materials with an improved or even new functional performances. In this study, a brand-new hybrid, containing both nanofibers and particles having a microsize, was fabricated using a sequential electrohydrodynamic atomization (EHDA) process. Firstly, the microparticles loaded with drug (berberine hydrochloride, BH) molecules in the cellulose acetate (CA) were fabricated using a solution electrospraying process. Later, these microparticles were suspended into a co-dissolved solution containned BH and a hydrophilic polymer (polypyrrolidone, PVP), and were co-electrospun into the nanofiber/microparticle hybrids. The EHDA processes were clearly recorded, and the resultant products showed a typical hybrid topography, with microparticles distributed all over the nanofibers, which was demonstrated by SEM assessments. FTIR and XRD demonstrated that the components within the hybrids were presented in an amorphous state and have fine compatibility with each other. In vitro dissolution tests verified that the hybrids were able to provide the designed dula-step drug release profiles, a combination of the fast release step of BH from the hydrophilic PVP nanofibers through an erosion mechanism and the sustained release step of BH from the insoluble CA microparticles via a typical Fickian diffusion mechanism. The present protocols pave a new way for developing trans-scale functional materials.

This article provides exact analytical formulae for various kinds of rainbow step barrier options. These are highly flexible and sophisticated multi-asset barrier options based on the following principle : the option life is divided into several time intervals on which different barriers are monitored w.r.t. different underlying assets. From a mathematical point of view, new formulae are provided for the first passage time of a multidimensional geometric Brownian motion to a boundary defined as a step function. The article shows how to implement the obtained valuation formulae in a simple and very efficient manner. Numerical results highlight a strong sensitivity of rainbow step barrier options to the correlations between the underlying assets.

Abstract: The YF3: (Eu3+, Nd3+) nanoparticles (orthorhombic phase, D ~ 130 nm)) were synthesized via the co-precipitation method with subsequent hydrothermal treatment and annealing. The Eu3+ τdecay linearly descends with the increase of temperature in the 80 - 320 K range. The τdecay (T) slope values of the annealed YF3: Eu3+ (2.5 and 5.0 mol. %) nanoparticles were the highest (110·10-4 and 67·10-4, μs/K in the whole 80 – 320 K range, respectively. Thus, these samples were chosen for further doping with Nd3+. The maximum Sa and Sr values based on the LIR (IEu/INd) function were 0.67 K-1 (at 80 K) and 0.86 %·K-1 (at 154 K), respectively. As it was mentioned above, the sin-gle-doped YF3: Eu3+ (2.5. %) nanoparticles showed the linearly decreasing τdecay (T) function (5D0 – 7F1 emission). The main idea of Nd3+ co-doping was to increase this slope value (as well as the sensitivity) by increasing the rate of τdecay (T) descent via the addition of one more tempera-ture-dependent channel of 5D0 excited state depopulation. Indeed, we managed to increase the slope (Sa) up to 180·10-4 K-1 at 80 K. This result is one of the highest compared to the world analogs.

T cell function is determined by transcriptional networks that are regulated by epigenetic programming via posttranslational modifications (PTMs) of histone proteins and DNA. Bottom-up mass spectrometry (MS) can identify histone PTMs, whereas intact protein analysis with high-field Fourier transform ion cyclotron resonance MS (FTICR-MS) can detect species missed by bottom-up approaches. We used high-resolution reversed-phase liquid chromatography (RPLC) FTICR-MS, alternating electron transfer dissociation (ETD) and collision-induced dissociation (CID) on precursor ions to maximize fragmentation of uniquely modified species. First online RPLC separation sorted histone families then weak cation exchange hydrophilic interaction liquid chromatography (WCX-HILIC) separated species heavily clad in PTMs. Tentative PTM identifications were assigned by matching peptide masses to predicted theoretical masses that were verified with tandem MS. We used this innovative approach for Histone-intact protein PTM mapping (HiPTMap) and to quantify PTMs on core histones purified from CD8+ T cells directly isolated ex vivo post-influenza infection. Activation significantly reduced PTMs in vivo following influenza infection, histone maps changed as T cells migrated to infections, and T cells responding to secondary heterologous infections had significantly more PTMs enhancing transcriptional activation. Thus, HiPTMap identifies and quantifies PTMs on CD8+ T cell histones and determines their combinations in T cell states.

Field and numerical investigations at Happisburgh, East coast of England, UK, sought to characterize beach thickness and determine geologic framework controls on coastal change. After a major failure of coastal protection infrastructure, removal of about 1 km of coastal defense along the otherwise protected cliffed coastline of Happisburgh triggered a period of rapid erosion over 20 years of ca. 140 m. Previous sensitivity studies suggested that that beach thickness plays a major role in coastal recession. These studies were limited, however, by a lack of beach volume data. In this study, we have integrated the insights gained from our understanding of the Quaternary geology of the area, a novel non-intrusive passive seismic survey method, and a 3D novel representation of the subsurface source and transportable material into a coastal modelling environment to explore the role of beach thickness on the back wearing and down wearing of the cliffs and consolidated platform, respectively. Results show that beach thickness is non-homogeneous along the study site: we estimate that the contribution to nearshore sediment budget via platform down wearing is of a similar order of magnitude as sediment lost from the beach and therefore non-negligible. We have provided a range of evidence to support the idea that the Happisburgh beach is a relatively thin layer perched on a sediment rich platform of sand and gravel. This conceptualization differs from previous publications, which assumes that the platform was mostly till and fine material. This has direct implication on the regional sediment management of along this coastline. The present study contributes to our understanding of a poorly known aspect of coastal sediment budgeting and outlines a quantitative approach that allows for simple integration of geological understanding for coastline evolution assessments worldwide.

Ice accumulation poses considerable challenges in transportation, notably in the domain of general aviation. The present study combines the strengths and limitations of conventional aircraft de-icing techniques with the emerging trend toward all-electric aircraft. The study aims to utilize laser-induced graphene (LIG) technology to create a multifunctional surface, seamlessly integrating hydrophobic properties with efficient electrical heating to mitigate surface icing effectively. We investigated the utilization of a 10.6 μm CO2 laser for direct writing on polyimide (PI), a widely-used insulating encapsulation material. From the thermomechanical perspective, our initial analysis using COMSOL Multiphysics software revealed that when the laser power P exceeds 5 W, the PI substrate experience ablative damage. The experimental results show that when P ≤ 5W, an increase in power has a positive impact on the quality, surface porosity, roughness reduction, line-spacing reduction, and water contact-angle enhancement of the graphene. Conversely, when P &gt; 5 W, higher power negatively affects both the substrate and the graphene structure by inducing excessive ablation. However, it influences the graphene line height positively and is consistent with overall experimental-simulation congruence. Furthermore, the incorporation of high-quality graphene resulted in a surface that exhibited higher contact angles (CA &gt; 120°), lower energy consumption, and higher heating efficiency compared to the use of traditional electrically heated materials for anti-icing applications. The potential applications of this one-step fabrication method extend across various industries, particularly aviation, marine engineering, and other ice-prone domains. Moreover, the method has extensive prospects for addressing pivotal challenges associated with ice formation and serves an innovative and efficient anti-icing technology.

Sleep quality is known to affect automatic and executive brain functions such as gait control and cognitive processing. This study aimed to assess the effect of dual tasks on gait spatiotemporal parameters among young adults with good and poor sleep quality in the United Arab Emirates. In total, 65 young adults with a mean age of 21.1±2.5 were assessed for gait analysis during single-task and dual-task conditions. The participants’ sleep quality was assessed using the Pittsburgh Sleep Quality Index (PSQI), and gait was assessed using the BTS Gaitlab System. The participants were asked to walk at natural speed as a single-task condition, followed by walking while performing a cognitive task as a dual-task condition. The parameters assessed included the gait velocity (m/s), cadence (steps/min), step width (m), and stride length (m). The DTC on each gait parameter was calculated. The Mann–Whitney U test was used to compare the differences in the DTC on gait variables between the good and poor sleep quality groups, and the Spearman correlation test was used to assess the correlation between total PSQI scores and the DTC. At a significance level of p&lt;0.05, a significant difference in cadence between the two sleep quality groups was observed, in addition to a positive correlation between sleep quality and the DTC effect on gait mean velocity, cadence, and stride length. Our findings also revealed a greater DTC on participants with poorer sleep quality. These findings contribute to our understanding of the significance of sleep quality in gait performance while multitasking in younger populations.

This paper presents a concise mathematical framework for investigating both feed-forward and backward process, during the training to learn model weights, of an artificial neural network (ANN). Inspired from the idea of the two-step rule for backpropagation, we define a notion of F_adjoint which is aimed at a better description of the backpropagation algorithm. In particular, by introducing the notions of F-propagation and F-adjoint through a deep neural network architecture, the backpropagation associated to a cost/loss function is proven to be completely characterized by the F-adjoint of the corresponding F-propagation relatively to the partial derivative, with respect to the inputs, of the cost function.

In current study we have obtained Co2FeSi-glass coated microwires with different geometrical aspect ratio, ρ = d/Dtot (diameter of metallic nucleus, d and total diameter, Dtot). The structure and magnetic properties are investigated at a wide range of temperature. XRD analysis illustrates a notable changing in the microstructure by increasing the aspect ratio of Co2FeSi glass coated microwires. Amorphous structure is detected for the sample with the lowest aspect ratio (ρ = 0.23), whereas a growth of crystalline structure is observed in the other samples (aspect ratio ρ = 0.30 and 0.43). This change at the microstructure properties correlates with dramatic changing in magnetic properties. For the sample with the lowest ρ -ratio, non-perfect square loops are obtained with low normalized remanent magnetization. A notable enhancement in the squareness and coercivity are obtained by increasing ρ -ratio. Changing the internal stresses strongly affects the microstructure, resulting in a complex magnetic reversal process. The thermomagnetic curves show large irreversibility for the Co2FeSi with low ρ -ratio. Meanwhile, if we increase the ρ -ratio, the sample shows perfect ferromagnetic behavior without irreversibility. The current result illustrates the ability to control the microstructure and magnetic properties of Co2FeSi-glass-coated microwires by changing only their geometric properties without performing any addition heat treatment. The modification of geometric parameters of Co2FeSi glass-coated microwires allows to obtain microwires which exhibit an unusual magnetization behavior that offers opportunities to understand the phenomena of various types of magnetic domain structures, which is essentially helpful for designing sensing devices based on thermal magnetization switching.

This paper presents a comprehensive review that highlights the characteristics of non-isolated step-up converters based on high boost voltage lifting techniques. The paper categorises the high boost techniques: multistage/multilevel, switched capacitor, voltage multiplier, voltage lift, switched inductor, and magnetic coupling. The paper also discusses in detail the advantages and disadvantages for each category such as cost, complexity, power density, reliability and efficiency. The number of passive and active components, voltage gain, voltage stress, switching frequency, efficiency and power rating are also compared. Although the paper considers coupling inductors in the context of the non-isolated converter, the focus of the entire article is on the non-isolated high voltage step-up techniques. The key contribution in this paper is the review of high boosting techniques rather than the DC /DC converters. This allows divergence of new ideas and new power converters that will help provide highly efficient and flexible power converters for several applications where the sending end voltage is very low as photovoltaic systems. In addition, many applications and control techniques of DC/DC converters are summarised in this paper.

We search for limit cycles in the dynamical model of two-species chemical reactions that contain seven reaction rate coefficients as parameters and at least one third-order reaction step, that is, the induced kinetic differential equation of the reaction is a planar cubic differential system. Symbolic calculations were carried out using the Mathematica (or, Wolfram language) mathematical program package, and it was also used for the numerical verifications to show the following facts: the kinetic differential equations of these reactions each has two limit cycles surrounding the stationary point of focus type in the positive quadrant. In the case of Model 1, the outer limit cycle is stable and the inner one is unstable that appears in a supercritical Hopf bifurcation. Moreover, the oscillations in a neighborhood of the outer limit cycle are slow-fast oscillations. In the case of Model 2, the outer limit cycle is unstable and the inner one is stable. With another set of parameters, the outer limit cycle can be made stable and the inner one unstable.

The seasonally adjusted civilian labor force participation rate, the sum of employed and unemployed persons as a percentage of the civilian non-institutional population, is analysed in the general to specific modelling framework with a saturating set of step indicators from January 1977 through June 2018. The results indicate that, ceteris paribus, the rise in the ratio of women to men in the labor force in addition to positive demographic movements can largely account for the rise in the labor force participation rate up to January 2000. Subsequently, the aging population helps to explain the decline. Recessions play a transitory role.

Rapid draw-down in an earthfill dam has serious implications for dam safety regarding slope stability. The evaluation of reservoir draw-down impact on slope stability was carried out considering the case study of 8 hours of rapid draw-down of the Middle Marsyangdi Hydroelectric Power Project (MMHPP) rock-fill dam using the Limit Equilibrium Method (LEM) and stress-based Finite Element Method (FEM). The time-dependent factor of safety (FOS) was evaluated and found that the 8 hours of rapid draw-down undertaken in October 2012 for reservoir flushing was unsafe with a draw-down rate of 1.91m/h. The resulting FOS of 1.28 and 1.27 using LEM and FEM was classified as unsafe as per the US Army Corps of Engineers’ guideline, the minimum required factors of safety should be greater than 1.3. The minimum safe allowable draw-down rate of 0.76m/h for 20 hours was identified. Applying three layers of horizontal filter materials and increasing the upstream dam’s permeability provided adequate FOS results for all cases by increasing seepage discharge to reduce the destabilizing excess pore water pressure. Several gradual draw-down rates were also tested and found that FOS increases with decreased draw-down rates, as it reduces the excess pore water pressure controlled with stabilizing existing water load.

The absolute absorption cross section of the ethyl peroxy radical, C2H5O2, in the Ã←X ̃ electronic transition with the peak wavelength at 7596 cm-1, has been determined by the method of dual wavelengths time resolved continuous wave cavity ring down spectroscopy. C2H5O2 radicals were generated from pulsed 351 nm photolysis of C2H6/Cl2 mixture in presence of O2 and detected on one of the CRDS paths. Two methods have been applied for the determination of the C2H5O2 absorption cross section: (i) based on Cl-atoms being converted alternatively to either C2H5O2 by adding C2H6 or to hydro peroxy radicals, HO2, by adding CH3OH to the mixture, whereby HO2 was reliably quantified on the second CRDS path in the 21 vibrational overtone at 6638.2 cm-1 (ii) based on the reaction of C2H5O2 with HO2, measured under either excess HO2 or under excess C2H5O2 concentration. Both methods lead to the same peak absorption cross section of C2H5O2,7596 cm-1 = (1.0±0.2) × 10-20 cm2. The rate constant for the cross reaction between of C2H5O2 and HO2 has been measured to be (6.5±1.6) × 10-12 cm3 molecule-1 s-1.

Nucleoside analogs are commonly used drugs for the treatment of cancer and viral infections. Nucleoside deoxyribosyltransferase (NDT) is one of the key enzymes required for the biosynthesis of deoxynucleotides. The feasibility of biochemical transformation processes is usually greatly dependent on the cost of biocatalysts. Therefore, immobilizing and reusing biocatalysts is an approach to be considered to bring biotransformations closer to industrial feasibility, since it not only allows enzymes to be reused but can also improve their stability under several reaction conditions. In this work, histidine tags have been successfully fused to a Nucleoside deoxyribosyltransferase from Lactobacillus reuteri (LrDNT), which has been produced in a bench-scale reactor using a facile araBAD promoter-based protein expression system in an industrial microorganism, the E. coli BL21(DE3) strain. The overexpressed LrNDT was bound to a nickel-chelating agarose affinity chromatography medium via a one-step purification and immobilization process with a 99% yield, retaining about 97% of its initial activity. The optimal conditions for the immobilized LrNDT maintain high enzyme activity within the range of 20-45°C and pH 6.0-7.5. Finally, the immobilized enzyme reactor (IMER) of LrNDT was applied for the continuous-flow biosynthesis of 2'-deoxyadenosine and retained 90% of its activity after 16 hours, providing a theoretical basis for the industrial production of nucleoside analogs.

Environmental regulation has dual effects on water resource utilization performance through various channels such as the "three red lines" and the "Porter hypothesis". Based on the detailed analysis of the impact path of environmental regulation on water resource utilization performance, the two-step system GMM method was adopted to test the dual effects of environmental regulation on water resource utilization performance by using panel data of 30 provinces and cities from 2004 to 2020. The results show that: (1) Environmental regulation has a significant direct impact on water resource utilization performance, and is currently in the stage of positive relationship of an inverted u-shaped relationship. (2) Environmental regulation has a significant indirect impact on water resource utilization Environmental regulation has dual effects on water resource utilization performance through various channels such as the "three-red lines" and the "Porter hypothesis". In accordance with a detailed examination of the influence path of environmental regulation on the performance of water resource utilization, the double effects of environmental regulation on water resource utilization performance were examined using panel statistics from 30 provinces and cities from 2004 to 2020 using the two-step system GMM approach. The results demonstrate that: (1) Environmental regulation has a direct effect on water resource utilization performance which is currently in the stage of the positive relationship of an inverted u-shaped relationship. (2) The influence of environmental regulation on water resource utilization performance through government intervention and industrial structure adjustment is indirect, among which government intervention can significantly improve water resource utilization performance, while the growth of the tertiary industry as a percentage can lower water resource utilization performance. (3) Both direct and indirect impacts indicate that enhancing the efficiency of the use of water resources is sustainable, and the water resource utilization performance of the preceding period had a major positive impact over the present phase. Therefore, the paper sets out a few policy suggestions, such as choosing reasonable environmental regulation tools, actively guiding the market-oriented reform with constraints, and upgrading the industrial structure in a green way.

In this study, the degradable superhydrophobic Mg/P/Z/F/H (magnesi-um/poly(-caprolactone)/zinc oxide/1H,1H,2H,2H-perfluorodecyltriethoxysilane (PFDTES)/ heating process) composite materials were prepared through one-step method for enhancing the corrosion resistance of AZ91D magnesium alloys. Electrochemical measurements showed that Mg/P/Z/F/H materials significantly improved the corrosion resistance of magnesium alloys in 3.5 wt.% NaCl. The self-cleaning, adhesion and stability tests suggested that Mg/P/Z/F/H composite materials had well self-cleaning properties, good adhesion strength and stability in wet atmosphere.

The study of different forms of preconditioners for solving a system of nonlinear equations, by using Newton’s method, is presented. The preconditioners provide numerical stability and rapid convergence with reasonable computation cost, whenever chosen accurately. Different families of iterative methods can be constructed by using a different kind of preconditioners. The multi-step iterative method consists of a base method and multi-step part. The convergence order of base method is quadratic and each multi-step add an additive factor of one in the previously achieved convergence order. Hence the convergence of order of an m-step iterative method is m + 1. Numerical simulations confirm the claimed convergence order by calculating the computational order of convergence. Finally, the numerical results clearly show the benefit of preconditioning for solving system of nonlinear equations.

. The Tau protein is associated with microtubule function in the neuron and is crucial for normal axonal transport. In several different neurodegenerative disorders, Tau misfolding leads to hyper-phosphorylation (p-Tau) and intracellular p-Tau aggregates known as neurofibrillary tangles (NFTs). This is particularly evident in individuals with Down syndrome (DS), who develop Alzheimer’s disease-like (AD) neuropathology early in life with almost complete penetrance, associated with the development of dementia symptoms in their 40s or 50s. Our previous findings have shown that certain forms of p-Tau are present already in childhood in individuals with DS in neuron-derived exosomes, suggesting an early phosphorylation profile in this population that could influence the development of AD pathology. Misfolded p-Tau isoforms are known to be seeding competent and may be responsible for spreading AD pathology in different regions of the brain. This review is focused on the accumulation of p-Tau in the brain of individuals with DS and potential consequences for brain function.

AISI 1050 steel circular pocket milling under minimum quantity lubrication (MQL) surroundings including nozzle elevation angle, lubricant flow rate, air pressure and cutting speed was studied. The machined surface quality (Ra) was evaluated for Up-milling side and Down-milling side. In this study, to obtain an manifest explanation on the pivotal effective parameters of MQL surroundings and cutting speed on the machined surface quality (Ra) through analyzing Taguchi L9 (34-2) approach and ANOVA calculation to identify those parameters, by utilizing the experimental outcomes to interpret three-dimensional (3D) surface plots and the diagrams of Signal-to-Noise ratios and major impact plots of Mean. The obtained outcomes of optimal operating parameters indicated that the pivotal effective parameters of MQL surroundings are nozzle elevation angle and lubricant flow rate on the machined surface quality. Simultaneously, a quadratic mathematical paradigm generated by using response surface design (RSD) and desirableness function evaluation were utilized to forecast the optimal values of the machined surface quality compared to Taguchi method. The results unveiled that the optimal values of the machined surface quality are adjacent to experimental attained values. The machined surface quality has been significantly improved using MQL surroundings.

Top-down models are defined by hardware architects to provide information on the utilization of the different hardware components. The target is to isolate the users from the complexity of the hardware architecture while giving them insight into how efficiently the code is using the resources. In this paper, we explore the applicability of 4 top-down models defined for different hardware architectures powering state-of-the-art HPC clusters (Intel Skylake, Fujitsu A64FX, IBM Power9, and Huawei Kunpeng 920) and propose a model for AMD Zen 2. We study a parallel CFD code used for scientific production to compare these 5 Top-Down models. We evaluate the level of insight achieved, the clarity of the information, the ease of use, and the conclusions that each one allows us to reach.

Dog Assisted Therapy is hypothesized to lower stress in children with Autism Spectrum Disorder (ASD) and children with Down Syndrome (DS), which may be visible on a physiological level. In this study, we measured Heart Rate Variability (HRV) and salivary cortisol of 20 children with DS or ASD at the beginning and end of 6 weekly sessions of Dog-Assisted Therapy. We found a decrease of cortisol levels during single sessions, but no overall effect after 6 sessions (6 weeks). The effect of Dog Assisted Therapy on the increase of HRV could not be confirmed. This study is one of the first to use physiological measurements to test the effects of DAT.

The advancement of performance in the domain of flexible wearable strain sensors has become increasingly significant due to extensive research on laser-induced graphene (LIG). An innovative doping modification technique is required owing to the limited progress achieved by adjusting laser parameters to enhance LIG’s performance. By pre-treating with AgNO3, we successfully manufactured LIG with a uniform dispersion of silver nanoparticles across its surface. The experimental results for the flexible strain sensor exhibit exceptional characteristics, including low resistance (183.4 Ω), high sensitivity (426.8), a response time of approximately 150 ms, and a relaxation time of about 200 ms. Moreover, this sensor demonstrates excellent stability under various tensile strains and remarkable repeatability during cyclic tests lasting up to 8,000 s. Additionally, this technique yields favorable results in finger bending and hand back stretching experiments, holding significant reference value for preserving the inherent characteristics of LIG preparation in a single-step and in situ manner.

This experimental study probes the dynamic behaviour of a 3mm ABS sheet during positive mould vacuum-assisted thermoforming. In this process, the sheet undergoes large and fast deformations, caused by the applied vacuum and mechanical stretching by the mould. The objective is to elucidate the complexities of these large, rapid and non-isothermal deformations. The non-isothermal conditions are caused by the radiative heating of the sheet, convective heat loss to the surrounding air and conductive heat transfer from the sheet to the mould. Utilizing stereo Digital Image Correlation (DIC) in tandem with thermal imaging, the present study accurately maps the occurring displacement, strain and strain rate field in relation to real-time temperature variation of the material. The study progresses to observe the ABS material from the moment it contacts the mould until it conforms to a positive 250mm diameter semi-sphere cast aluminium mould. The DIC methods are validated by comparing thickness values derived from DIC’s principal strain directions to ultrasonic thickness gauge readings. This knowledge not only broadens the understanding of the thermo-mechanical behaviour of the material but also aids in optimizing process parameters for improved thickness uniformity in thermoformed products.

Individuals with Parkinson’s disease (PD) and freezing of gait (FOG) have a loss of presynaptic inhibition (PSI) during anticipatory postural adjustments (APAs) for step initiation. The mesencephalic locomotor region (MRL) has connections to the reticulospinal tract that mediates inhibitory interneurons responsible for modulating PSI and APAs. Here, we hypothesized that MLR activity during step initiation would explain the loss of PSI during APAs for step initiation in freezers. Thirty-four freezers were assessed in the ON-medication state. During a functional magnetic resonance imaging protocol of simulated APA task, we assessed beta of blood oxygenation level-dependent signal change of areas known to initiate and pace gait (e.g., MLR), in addition to PSI of the soleus muscle during APA for step initiation, and clinical (e.g., disease duration) and behavioral (e.g., FOG severity and APAs amplitude for step initiation) variables. A linear multiple regression model showed that MLR activity (R2=0.32, P=0.0006) and APA amplitude (R2=0.13, P=0.0097) explained together 45% of the loss of PSI during step initiation in freezers. Decreased MLR activity during a simulated APA task is related to a higher loss of PSI during APA for step initiation. Deficits in central and spinal inhibitions during APA may be related to FOG pathophysiology.

Usually, the two-bath dyeing process using disperse dyes and reactive dyes separately was employed for the dyeing of PC blends. The cost of the double bath, dyeing cycle, energy consumption and chemical consumption is quite higher than the one-step or single bath dyeing methods. In this study, the one-bath dyeing process using one kind of dye was investigated. Polyester cotton blends dyed in one-bath one-step dyeing methods with disperse dye after surface modifications of cotton by acetylation methods were studied. Surface modification of cotton was carried out using fibrous acetylation methods. The effect of acetic anhydride and time on percent acetyl content at room temperature was studied. Modified polyester/cotton was carried out in HTHP dyeing machine incorporates with different dye concentrations and dyeing temperature. Surface chemistry, thermal decomposition property and moisture regain of modified polyester/ cotton blend are evaluated. The color strength of the dyed fabrics and their fastness properties to washing, light, and rubbing as well as tear strength and abrasion resistance were evaluated. The effect of dye concentration and temperature color strength, tensile strength warp and weft direction was assessed. The optimum value for surface modification was obtained with a concentration of acetylation agent 16% and time of reaction 2.5 hours, gave percent acetylation of 34. An FTIR spectrum shows acetylation resonance. The experiment result of dyeing showed that the optimum value was obtained with dye concentration above 1% at a temperature of 120oC, warp tensile strength decreased by 12% and weft tensile strength was decreased by 9% from the control half-bleached fabric. Results of this study showed that a one-step one-bath dyed modified polyester/cotton blend with disperse dye fabric presents good fastness property compared with conventional two-bath dyed fabric as well as colour strength values.

In wireless sensor networks (WSNs), each sensor node can estimate the global parameter from the local data in distributed manner. This paper proposed a robust diffusion estimation algorithm based on minimum error entropy criterion with self-adjusting step-size, which are referred to as diffusion MEE-SAS (DMEE-SAS) algorithm. The DMEE-SAS algorithm has fast speed of convergence and is robust against non-Gaussian noise in the measurements. The detailed performance analysis of the DMEE-SAS algorithm is performed. By combining the DMEE-SAS with diffusion minimum error entropy (DMEE) algorithms, an Improving DMEE-SAS algorithm is proposed, in non-stationary environment where tracking is very important. The Improving DMEE-SAS algorithm can avoid insensitivity of the DMEE-SAS algorithm due to the small effective step-size near the optimal estimator, and obtain a fast convergence speed. Numerical simulations are given to verify the effectiveness and advantages of these proposed algorithms.

Furthermore, the nasal congestion typical of rhinitis can contribute to upper airway obstruction and sleep-disordered breathing. A vicious circle is created between asthma and sleep-disordered breathing: uncontrolled asthma and sleep-disordered breathing can worsen each other. In children with genetic obesity, despite alterations in the immune system, fewer allergies are found compared to the general population. The causes of this reduced allergenicity are unclear but probably involve genetic, immunological, and environmental factors. Further studies are needed to understand the mechanisms. The study emphasizes the importance of jointly evaluating and managing allergies, obesity, and sleep-disordered breathing in children, considering their close interconnection.

Typically, a diesel generator on the merchant ship, composed of a wound rotor synchronous generator and a four-stroke diesel engine, supplies electrical power to various loads. Recently, shaft generators for merchant vessels are increasingly replacing diesel generators to reduce CO2 emissions through fuel efficiency improvement. In particular, permanent magnet generators replace induction generators due to their high-efficiency characteristics at light loads. The surface-mounted permanent magnet can be a suitable rotor topology due to the relatively short constant power range. This generator can also operate as a motor according to the propulsion mode, so minimizing the harmonics of the induced voltage and the torque ripple is necessary. This paper proposes an alternative NdFeB magnet pole topology combined with the modular step-skewed rotor. The step-skewed rotor affects to reduce higher-order harmonics, and the modular pole reduces the permanent magnet assembly process and harmonics in voltage and torque. A 2-D finite element method is used to evaluate the harmonics of induced voltage and torque pulsation for the proposed topology. The topology shows harmonic minimization effect by comparing the characteristics of three flatted-bottom magnets. Compared to the tapered bread-loaf magnet, voltage harmonics to the 100th component are almost the same, and the torque ripple is reduced by more than 12% at the same residual flux density. The analysis method is verified by comparing test and analysis results for prototype machines with similar specifications.

The class of A-stable symmetric one-step Hermite-Obrechkoff (HO) methods introduced in [1] for dealing with Initial Value Problems is analyzed. Such schemes have the peculiarity of admitting a multiple knot spline extension collocating the differential equation at the mesh points. As a new result, it is shown that these maximal order schemes are conjugate symplectic which is a benefit when the methods have to be applied to Hamiltonian problems. Furthermore a new efficient approach for the computation of the spline extension is introduced, adopting the same strategy developed in [2] for the BS linear multistep methods. The performances of the schemes are tested in particular on some Hamiltonian benchmarks and compared with those of the Gauss Runge-Kutta schemes and Euler-Maclaurin formulas of the same order.

Device-mediated, non-invasive drug delivery across the blood-brain barrier (BBB) represents a significant advancement in treating neurological diseases. The BBB is a tightly packed layer of endothelial cells that shields the brain from harmful substances in the blood, allowing necessary nutrients to pass through. It is a highly selective barrier, which poses a challenge to delivering therapeutic agents into the brain. Several non-invasive techniques and devices have been proposed or investigated to enhance drug delivery across the BBB. This paper presents the current state of the art and case studies that address the pharmacology, technology, delivery systems, regulatory approval, ethical concerns, and future possibilities.

Anthropogenic chemicals are fundamental to our standard of living in modern society. Unfortunately, some chemicals are persistent and can enter waste streams and ultimately the environment. Commonly used household products including pharmaceuticals and personal care products are an important source of contaminants. The aim of this study was to develop an “Up-the-pipe Solutions” framework to raise awareness about the presence and potential risks of chemicals found in household products to reduce their levels in waste streams or substitute them with less harmful alternatives. This approach based on The Natural Step framework and the concept of essentiality recognises the importance of engaging the community to raise awareness around the consequences of our daily activities and behavioural patterns that can lead to the release of persistent contaminants in main waste streams from the kitchen and bathroom and green wastes we generate.

Q345 steel is widely used in the construction industry, vehicle manufacturing industry, bridge construction industry and many other aspects due to its excellent comprehensive performance. However, due to its high silicon content, direct hot-dip galvanizing will lead to a series of problems, such as easy peeling of the coating due to the "silicon reactivity". In this paper, we adopt the "two-step hot-dipping method", first hot-dip aluminizing and then hot-dip galvanizing, to isolate the substrate and zinc liquid direct contact, so as to avoid the occurrence of "silicon reactivity". Through the microstructure characterization, neutral salt spray corrosion experiments, electrochemical experiments, the results show that: Al-Zn composite coatings from the inside out were perpendicular to the substrate growth of loose Fe2Al5 layer and Al-Zn layer, outbursts generation; Al-Zn composite coatings resistance to neutral salt spray corrosion was far more than the substrate; Al-Zn composite coatings polarization curve corrosion potential than the substrate was lower than that of the substrate by 0.512V, showing a strong corrosion resistance. It shows extremely strong corrosion resistance.

The introduction of stool as a readily obtainable sample and the recently developed simple-one-step (SOS) stool processing method offer an opportunity for TB diagnosis in children. We conducted this study at secondary health facilities in Ethiopia which are the first level referral facilities for childhood TB diagnosis and treatment with the aim to determine if stool-based TB diagnosis can be performed with reasonable level of concordance with sputum tests in using Xpert MTB/RIF Ultra. Eligible children 0-14 years with presumptive pulmonary TB were asked to provide stools in addition to routinely requested sputum samples. We computed Cohen’s kappa statistic in SPSS to determine the level of agreement between stool and sputum test results. Of the 373 children included in the study, 61% were &lt;5 years of age and 56% were male. Thirty-six children (9.7%) were diagnosed with TB and all started treatment. The rate of concordance between stool and sputum was high with kappa value of 0.83 (P&lt;0.001). There were more Xpert ultra positive test results on stool (n=27 (7.2%)) than on sputum/NGA (n=23 (6.2%)). Laboratories in secondary hospitals can perform stool-based TB diagnosis in children with high concordance between stool and sputum test results reaffirming the applicability of the SOS method.

The objective of this study was to evaluate the efficacy of one-step nucleic acid amplification (OSNA) for the detection of sentinel lymph node (SLN) metastasis compared to standard pathological ultrastaging in patients with early-stage endometrial cancer (EC). A total of 526 SLNs from 191 patients with EC were included in the study. 379 SLNs (147 patients) were evaluated by both methods, OSNA and standard pathological ultrastaging. The central 1-mm portion of each lymph node was subjected to semi-serial sectioning at 200-μm intervals and examined by hematoxylin-eosin and immunohistochemistry with CK19; the remaining tissue was analysed by OSNA for CK19 mRNA. The OSNA assay detected metastases in 19.7% of patients (14.9% micrometastasis and 4.8% macrometastasis), whereas pathological ultrastaging detected metastasis in 8.8% of patients (3.4% micrometastasis and 5.4% macrometastasis). Using the established cut-off value for detecting SLN metastasis by OSNA in EC (250 copies/μl), the sensitivity of the OSNA assay was 92%; specificity was 82%; diagnostic accuracy was 83%, and the negative predictive value was 99%. Discordant results between both methods were recorded in 20 patients (13.6%). OSNA resulted in an upstaging in 12 patients (8.2%). OSNA could aid in the identification of patients requiring adjuvant treatment at the time of diagnosis.

This work communicates cavity ring-down spectroscopy (CRDS) of methylidyne (CH) in a chemiluminescent plasma that is produced in a microwave cavity. Of interest are the rotational lines of the 0-0 vibrational transition for the A-X band and the 1-0 vibrational transition for the B-X band. The reported investigations originate from CH-radical research in 1996 that constituted the first case of applying CRDS to the CH radical. The report also includes recent analysis that shows excellent agreement of measured and computed data, and it communicates CH line strength data.

The Asian world is home to a multitude of venomous and dangerous snakes, which are attributed to various medical effects used in the preparation of traditional snake tinctures and alcoholics, like the Japanese snake wine, named Habushu. The aim of this work was to perform the first quantitative proteomic analysis of the Protobothrops flavoviridis pit viper venom. Accordingly, the venom was analyzed by complimentary bottom-up and top-down mass spectrometry techniques. The mass spectrometry-based snake venomics approach revealed that more than half of the venom is composed of different phospholipases A2 (PLA2). The combination with an intact mass profiling led to the identification of the three main Habu PLA2s. Furthermore, nearly one-third of the total venom consists of snake venom metalloproteinases and disintegrins, and several minor represented toxins families were detected: CTL, CRISP, svSP, LAAO, PDE and 5’-nucleotidase. Finally, the venom of P. flavoviridis contains certain bradykinin-potentiating peptides and related peptides, like the svMP inhibitors pEKW, pEQW, pEEW and pENW. In preliminary MTT cytotoxicity assays the highest cancerous-cytotoxicity of the crude venom was measured against human neuroblastoma SH-SY5Y cells and shows in some fractions disintegrin-like effects.

The aim of this paper is to apply all the existing pyranometric method, to estimate the sunshine duration from the global solar irradiation, in order to find in their original form the most suitable method for a tropical site. Then, in a second step, one of these methods will be optimized to well fit tropical sites. Five methods in the literature (Step Algorithm, Carpentras Algorithm, Slob &amp; Monna Algorithm, Slob &amp; Monna 2 Algorithm, and Linear Algorithm) were applied with eleven years of global and diffuse solar radiation data. As a result, in their original form, the Step Algorithm is on the first rank. But in the second step, after improving its main coefficients, the Carpentras Algorithm was found to be the best algorithm for tropical site in the southern hemisphere.

Abstract: Background and objectives: Symptomatic walled-off pancreatic necrosis is a serious local complication of acute necrotising pancreatitis. The endoscopic step-up approach is the standard treatment for symptomatic walled-off pancreatic necrosis; however, adjunctive radiologic percu-taneous drainage for this condition is controversial. This study compared the clinical and radio-logic resolution of walled-off pancreatic necrosis achieved with the endoscopic step-up approach with or without radiology-guided percutaneous drainage. Material and Methods: This retrospective, single-center cohort study enrolled patients with symp-tomatic walled-off pancreatic necrosis who underwent endoscopic transmural drainage (ETD) followed by directed endoscopic necrosectomy (DEN) with or without radiology-guided drainage. A total of 34 patients (endoscopic approach, n=22; combined modality approach, n=12) underwent the endoscopic step-up approach (ETD followed by DEN). Baseline characteristics, clinical success, and resolution of necrosis were compared between groups. Results: All patients achieved symptom resolution from walled-off pancreatic necrosis. The mean patient age was 58.4 years, and 21 (61.8%) were men. After treatment with the endoscopic approach and combined modality approach, clinical success was achieved in 90.9% of patients within 11.5 days, and 66.7% of patients within 16.5 days, respectively. Both the total hospital stay (55 days vs 71 days; p=0.071) and time to complete radiologic resolution were shorter (93 days vs 124 days; p=0.23) in the endoscopic approach group. Conclusion: The endoscopic step-up approach resulted in the clinical resolution of symptomatic walled-off pancreatic necrosis comparable to that of the combined modality drainage. However, the endoscopic approach alone allows higher clinical success, early clinical and radiologic resolution, and a shorter hospital stay.

Classical enzyme kinetics are summarized and linked with modern discoveries here. The time course of sequential catalytic events by biological macromolecular enzyme is analyzed at the molecular level; the relationships between catalytic efficiency (turnover number), catalytic rate/velocity, the amount of time taken and physical/biochemical conditions of the system are discussed. This writing tries to connect the microscopic molecular behavior of enzyme to kinetic data obtained in experiment, and the hypothesis proposed here provide an interpretation to previous experimental observations and can be testified by future experiments.

This paper develops mathematical models examining possible roles of oxytocin and oxytocin receptors in the development of autism. This is done by demonstrating that mathematical operations on normalized data from the Stanford study (K.J. Parker, 2016), which establishes a correspondence between severity of autism in children and their oxytocin blood levels, generates a graph that is the same as the graph of mathematical operations on a normalized theoretical model for the severity of autism. This procedure establishes the validity of the theoretical model and the significance of oxytocin receptors in autism. A steady-state model follows, explaining the constant baseline concentrations of oxytocin observed in the cerebral spinal fluid and blood in terms of the neuromodulation by oxytocin of oxytocin receptors on the magnocellular neurons that produce oxytocin in nuclei in the hypothalamus. The implications of these models for possible roles of oxytocin and oxytocin receptors in autism is considered for several unrelated conditions that may be associated with autism. These are: oxytocin receptor desensitization and down-regulation as factors during labor in offspring autism development; reductions in the oxytocin receptor numbers in the fixed oxytocin receptor expression that occurs before birth; MAST Immune System disease; and the excess number of dendritic spines from lack of pruning observed in brains of autistic people. Research into the feasibility of generating magnocellular neurons and other neurons from adult stem cells is suggested as a way of doing invitro studies of oxytocin and oxytocin receptors to assess the validity of theories presented in this paper.

Arrhythmic sudden cardiac death (SCD) has an annual prevalence of 1 per 1000 while 75% of the victims suffer from ischemic and 10% from non-ischemic or hypertrophic cardiomyopathy. Altogether, these three entities account for more than 80% of the total SCD victims. Guidelines for implantable cardiac defibrillators are still dominated by LVEF<30% from the MADIT II study. In terms of arrhythmic risk stratification, the PRESERVE-EF study restored in clinical practice the two-step arrhythmic risk stratification approach based on Electrocardiographic non-invasive risk factors (NIRFs) guiding to electrophysiological study. In our times with the multiple cardiac imaging methods and artificial intelligence applications availability, this two-step approach based on integrated arrhythmia mechanisms detection, emerges as an efficient SCD risk stratification paradigm for these three entities but also for the patients with congenital heart disease.

Liquid crystal elastomers (LCEs) are shape morphing materials whose large and reversible shape transformation results from the coupling between the mobile anisotropic properties of liquid crystal (LC) units and the rubber elastic of polymer networks. Their shape changing behaviors under the stimuli are largely directed by LC orientations, and therefore various strategies have been developed to spatially modulate the LC alignments. But most of the methods suffer from complex fabrication technologies or intrinsic limitations in applicability. To address this issue, programmable complex shape changes in some types of LCEs, such as polysiloxane side-chain LCEs or thiol-acrylate main-chain LCEs, etc, have been achieved by using a mechanical alignment programming process coupled with two-step crosslinking. Here, we report a polysiloxane main-chain LCE with programmable 2D and 3D shape changing performances achieved by mechanically programming the polydomain LCE between the two crosslinking steps. The resulting LCEs exhibited reversible thermal induced shape transformation between the initial and programmed shapes due to the two-way memory between the first network structure and the second network structure. Our work would be potential for expanding the applications of LCE materials in actuators, soft robotics and smart structures where arbitrary and easily programmed shape morphings are needed.

The molecular basis of Down syndrome (DS) predisposition to leukemia is not fully understood but involves various factors such as chromosomal abnormalities, oncogenic mutations, epigenetic alterations, and changes in selection dynamics. Myeloid leukemia associated with DS (ML-DS) is preceded by a preleukemic phase called transient abnormal myelopoiesis driven by GATA1 gene mutations and progresses to ML-DS through additional mutations in cohesin genes, CTCF, RAS, or JAK/STAT pathway genes. DS-related ALL (ALL-DS) differs from non-DS ALL in terms of cytogenetic subgroups and genetic driver events and aberrant expression of CRLF2, JAK2 mutations, and RAS pathway activating mutations are frequent in ALL-DS. Recent advancements in single-cell multi-omics technologies have provided unprecedented insights into the cellular and molecular heterogeneity of DS-associated hematologic neoplasms. Single-cell RNA sequencing and digital spatial profiling enable the identification of rare cell subpopulations, characterization of clonal evolution dynamics, and exploration of the tumor microenvironment's role. These approaches may help identify new druggable targets and tailor therapeutic interventions based on distinct molecular profiles, ultimately improving patient outcomes with the potential to guide personalized medicine approaches and the development of targeted therapies.

In the present paper, we efficiently solve the two-body problem for extreme cases such as those with high eccentricities. The use of numerical methods, with the usual variables, cannot maintain the perihelion passage accurately. In previous articles, we have verified that this problem is treated more adequately through temporal reparametrizations related to the mean anomaly through the partition function. The biparametric family of anomalies, with an appropriate partition function, allows a systematic study of these transformations. In the present work, we consider the elliptical orbit as a meridian section of the ellipsoid of revolution, and the partition function depends on two variables raised to specific parameters. One of the variables is the mean radius of the ellipsoid at the secondary, and the other is the distance to the primary. One parameter regulates the concentration of points in the apoapsis region, and the other produces a symmetrical displacement between the polar and equatorial regions. The three most used geodesy latitude variables are also studied, resulting in one not belonging to the biparametric family. However, it is in the one introduced now, which implies an extension of the biparametric method. The results obtained by the method presented here now allow a causal interpretation of the operation of numerous reparametrizations used in the study of orbital motion.

This study evaluates the accessibility of primary care physicians (PCPs) in Eastern Quebec using an enhanced two-step floating catchment area (E2SFCA) methodology. The E2SFCA methodology considers both the population supply of PCPs and the travel time between PCPs and dissemination areas, and was found to be effective in identifying possibly underserved areas. The availability of primary care services is contingent upon the presence of adequate road infrastructure, and populations residing in areas with limited access to main road networks may experience compromised access to primary care. The study concludes that the E2SFCA methodology can facilitate the identification of areas experiencing a shortage of PCPs, and this information can be used to inform the development of regional medical workforce programs and support the establishment of rural residency initiatives.

Cemented rock fill (CRF) is commonly used in cut-and-fill stoping operation in underground mining. This allows for the maximum recovery of ore. Backfilling can improve stope stability in underground workings, and then improve ground stability of the whole mine site. Backfilling step scenarios vary from site to site. This paper presents the investigation of five different backfilling step scenarios and their impacts on the stability of stopes at four different mining levels. A comprehensive comparison of displacements, major principal stress and stress concentration factor (SCF) was conducted. The results show that different backfilling step scenarios have little influence on the final displacement for displacement in the stopes. Among the five backfilling scenarios, the major principal stress and stress concentration factor (SCF) have almost the same final results. The backfilling scenario SCN-1 is the optimum option among these five backfilling scenarios. It can immediately prevent the increase of the displacement and reduce the sidewall stress concentration, thereby preventing possible failures. Using the same strength of CRF can achieve same effects among the four mining levels. Applying backfilling CRF of the same strength at different mining depths is acceptable and feasible to improve the stability of the stopes.

Research within the field of hydrology often focuses on comparing stochastic to machine learning (ML) forecasting methods. The comparisons performed are all based on case studies, while an extensive study aiming to provide generalized results on the subject is missing. Herein, we compare 11 stochastic and 9 ML methods regarding their multi-step ahead forecasting properties by conducting 12 large-scale computational experiments based on simulations. Each of these experiments uses 2 000 time series generated by linear stationary stochastic processes. We conduct each simulation experiment twice; the first time using time series of 100 values and the second time using time series of 300 values. Additionally, we conduct a real-world experiment using 405 mean annual river discharge time series of 100 values. We quantify the performance of the methods using 18 metrics. The results indicate that stochastic and ML methods perform equally well.

Color change is the most obvious characteristic of tomato ripening stage and an important indicator of tomato ripening condition, which directly affects the commodity value of tomato. To visualize the color change of tomato fruit in mature stage, a gated recurrent unit network with an encoder-decoder structure that dynamically simulates tomato growth and development with time-dependent lines using tomato color and shape as real-time data was proposed in this paper. Firstly, the .json file was converted into a mask.png file, the tomato mask was extracted, and the tomato was separated from the complex background environment, and the tomato growth and development data set was successfully constructed. Then, a network of gated recurrent units with encoder-decoder structure was constructed to predict the future growth trend of tomato under different greenhouse temperatures. The experimental results showed that for the gated recurrent unit network of encoder-decoder structure proposed, when the hidden layer number was 1 and hidden layer number was 512, a high consistency and similarity between the model predicted image sequence and the actual growth and development image sequence would be realized, and the structural similarity index measure was 0.746. It was proved that when the average temperature was 24.93℃, the average soil temperature was 24.06℃, and the average light intensity was 11.26 Klux, the environment was the most suitable for tomato growth. The environmental data-driven tomato growth model was constructed to explore the growth status of tomato under different environmental conditions, thus to understand the growth status of tomato in time. The statement provided a theoretical foundation for determining the optimal greenhouse environmental conditions to achieve tomato maturity. And it offered recommendations for investigating the growth cycle of tomatoes, as well as technical assistance for standardized cultivation in solar greenhouses.

The effects of wastewater step-feeding on the performance of Horizontal Subsurface Flow Constructed Wetlands (HSF CWs) are numerically investigated. The purpose is to check if this alternative feeding technique increases the ability of HSF CWs to remove pollutants. Two methodologies are used: Initially, the Tanks-In-series (TIS) methodology, based on Finite Volume Method (FVM), is analyzed by using the volumetric degradation coefficient λ. In this case the operation of CW is similar with a series of Continuous Stirred-Tank Reactors (CSTR), under steady conditions. Then, the Step-Feeding (SF) procedure is presented, when the CW is operated like a Plug Flow Reactor (PFR). The results show that the SF procedure does not improve the performance of HSF CWs on removing Biochemical Oxygen Demand (BOD), operating under Mediterranean conditions.

Mapping vegetation species is critical to facilitate related quantitative assessment, and for invasive plants mapping their distribution is important to enhance monitoring and controlling activities. Integrating high resolution multispectral remote sensing (RS) image and lidar (light detection and ranging) point clouds can provide robust features for vegetation mapping. However, using multiple source of high-resolution RS data for vegetation mapping at large spatial scale can be both computationally and sampling intensive. Here we designed a two-step classification workflow to decrease computational cost and sampling effort, and to increase classification accuracy by integrating multispectral and lidar data to derive spectral, textural, and structural features for mapping target vegetation species. We used this workflow to classify kudzu, an aggressive invasive vine, in the entire Knox County (1,362 km2) of Tennessee, the United States. Object-based image analysis was conducted in the workflow. The first-step classification used 320 kudzu samples and extensive coarsely labeled samples (based on national land cover) to generate an overprediction map of kudzu using random forest (RF). For the second step, 350 samples were randomly extracted from the overpredicted kudzu and labeled manually for the final prediction using RF and support vector machine (SVM). Computationally intensive features were only used for the second-step classification. SVM had constantly better accuracy than RF, and the Producer’s Accuracy, User’s Accuracy, and Kappa for the SVM model on kudzu was 0.94, 0.96, and 0.90, respectively. SVM predicted 1010 kudzu patches covering 1.29 km2 in Knox County. We found the sample size of kudzu used for algorithm training impacted the accuracy and number of kudzu predicted. The proposed workflow could also improve sampling efficiency and specificity. Our workflow had much higher accuracy than the traditional method conducted in this research, and could be easily implemented to map kudzu in other regions or other vegetation species.

As there exist no repulsive forces in strong interaction, in a hypothetical approach, strong interaction can be assumed to be equivalent to a large gravitational coupling. Based on this concept, strong coupling constant can be defined as a ratio of the electromagnetic force and the gravitational force associated with proton, neutron, up quark and down quark. With respect to the product of strong coupling constant and fine structure ratio, we review our recently proposed two semi empirical relations and coefficients 0.00189 and 0.00642 connected with nuclear stability and binding energy. We wish to emphasize that- by classifying nucleons as ‘free nucleons’ and ‘active nucleons’, nuclear binding energy can be fitted with a new class of ‘three term’ formula having one unique energy coefficient. Based on the geometry and quantum nature, currently believed harmonic oscillator and spin orbit magic numbers can be considered as the lower and upper “mass limits” of quark clusters.

Insufficient mixing in large-scale bioreactors, provokes gradient zones of substrate, dissolved oxygen, pH and other parameters. E. coli responds to a high glucose, low oxygen feeding zone with the accumulation of mixed acid fermentation products, especially formate, but also with the synthesis of non-canonical amino acids, such as norvaline, norleucine and -methyl-norleucine. These amino acids can be mis-incorporated into recombinant products, which causes a problem for pharmaceutical production whose solution is not trivial. While these effects can also be observed in scale down bioreactor systems, these are challenging to operate. Especially the high-throughput screening of clone libraries is not easy, as fed-batch cultivations would need to be controlled via repeated glucose pulses with simultaneous oxygen limitation, as has been demonstrated in well controlled robotic systems. Here we show that not only glucose pulses in combination with oxygen limitation can provoke the synthesis of these non-canonical branched-chain amino acids, but also that pyruvate pulses produce the same effect. Therefore we combined the enzyme based glucose delivery method Enbase® in a PALL24 mini-bioreactor system and combined repeated pyruvate pulses with simultaneous reduction of the aeration rate. These cultivation conditions, produced an increase in the non-canonical branched chain amino acids norvaline and norleucine in both the intracellular soluble protein and inclusion body fractions with mini-proinsulin as an example product, and this effect was verified in a 15 L stirred tank bioreactor. To our opinion this cultivation strategy is easy to apply for the screening of strain libraries under standard laboratory conditions if no complex robotic and well controlled parallel cultivation devices are available.

In this article, the multitouch option, also called the n  touch option (or the “baseball” option when n  3 ) is analyzed and valued in closed form. This is a kind of barrier option that sets a gradual knockout / knock-in mechanism based on the number of times the underlying asset has crossed a predefined barrier in various time intervals before expiry. The higher the number of predefined time intervals during which the barrier has been touched, the lower the value of a knock-out contract at expiry, and conversely for a knock-in one. Multitouch options can be viewed as an extension of step barrier options, preserving the ability of the latter to adjust the exposure to risk over time, while eliminating the notorious danger of “sudden death” that holders of step barrier options are faced with. Unlike occupation time derivatives, the payoff at expiry does not depend on the amount of time spent outside the authorized range, but on the number of passages beyond the authorized range.

Apraxia of speech is a persistent speech motor disorder that affects speech intelligibility. Studies on speech motor disorders with transcranial Direct Current Stimulation (tDCS) have been mostly directed to post-stroke aphasia. Only a few tDCS studies have focused on apraxia of speech or childhood apraxia of speech (CAS), and no study has investigated individuals with CAS and people with trisomy 21 (T21, Down Syndrome). This study examined the effects of tDCS combined with a motor learning task in developmental apraxia of speech co-existing with T21 (ReBEC RBR-5435x9). The accuracy of speech sound production of nonsense words (NSWs) during Rapid Syllable Transition Training (ReST) under 10 sessions of anodal tDCS (1.5 mA, 25 cm) over the Broca’s area with cathode over the contralateral region was compared to 10 sessions of sham-tDCS and 4 control sessions in a 20-year-old male individual with T21 presenting moderate-severe childhood apraxia of speech (CAS). The accuracy for NSWs production progressively improved (gain 40%) under tDCS only (sham-tDCS and control sessions showed <20% gain). A decrease in speech severity from moderate-severe to mild-moderate indicated transfer effects in speech production. The speech accuracy under tDCS was correlated with Wernicke’s area activation (P3 current source density), which in turn, was correlated with the activation of the left supramarginal gyrus and the Sylvian Parietal Temporal Junction. Repetitive bihemispheric tDCS paired with ReST may have facilitated the speech sound acquisition in a young adult with T21 and CAS, possibly by recruiting brain regions required for the phonological working memory.

Sanitation, water supply and their governance remain major challenges in many Pacific Island Countries. National sustainable development strategies (NSDSs) are promoted throughout the Pacific as overarching improved governance instruments to identify priorities, plan solutions and fulfill commitments to sustainable development. Their relevance to local village-level development priorities is uncertain. The Kingdom of Tonga provides opportunities to compare both. Tonga’s Strategic Development Frameworks (TSDFI 2011-2014 and TSDFII 2015-2025) were developed to focus government and its agencies on national outcomes. From 2007 to 2016, 136 villages throughout Tonga’s five Island Divisions (IDs) formulated Community Development Plans (CDPs) involving separately 80% of women, youth and men in each village. Censuses in 2006 and 2016 show linked improvements in water supply and sanitation systems but reveal IDs with continuing challenges. Sanitation and water are prominent in TSDFI but absent from the current TSDFII. In contrast, CDPs show in one ID, 53% of villages ranked sanitation as a priority with marked differences between IDs and between women, youth and men. CDPs’ sanitation priorities in IDs mostly correspond to sanitation and water metrics in the Censuses, but some reflect impacts of natural disasters. Explanations for differences in sanitation priorities between national and local development plans, as well as suggestions for improving NSDS processes in island countries, are advanced.

This work presents the mathematical framework of the Second-Order Comprehensive Adjoint Sensitivity Analysis Methodology for Response-Coupled Forward/Adjoint Linear Systems (abbreviated as “2nd-CASAM-L”), which enables the most efficient computation of exactly obtained mathematical expressions of first- and second-order sensitivities of a generic system response with respect to functions (“features”) of model parameters. Subsequently, the first- and second-order sensitivities with respect to the model’s uncertain parameters, boundaries, and internal interfaces are obtained analytically and exactly, without needing large-scale computations. Within the 2nd-FASAM-L methodology, the number of large-scale computations is proportional to the number of model features (defined as functions of model parameters), as opposed to being proportional to the number of model parameters, which are considerably more than the number of features, being incomparably more efficient and more accurate than any other methods (statistical, finite differences, etc.) for computing exact expressions of response sensitivities (of any order) with respect to the model’s features and/or primary uncertain parameters, boundaries, and internal interfaces. The application of the 2nd-CASAM-L methodology is illustrated using a simplified energy-dependent neutron transport model of fundamental significance in nuclear reactor physics.

In 2015, the Self-Action Leadership Theory—a qualitative, nomological expansion of self-leadership theory rooted in atmospheric and astronomical metaphor aimed at expanding the personal freedom of individuals, organizations, and nations by bolstering the existential growth of individuals through a series of Maslow-esque stages of holistic, personal development. This article introduces an accompanying, practitioner-based Model of Self-Action Leadership (SAL) aimed at the implicit enhancement of a holistic range of administrative processes through explicit training, mentoring, and coaching in the model’s general and universally-applicable principles and practices. The SAL model produces an original construct of personal leadership practice that builds upon the extant self-leadership academic canon, which dates back to 1983 (Manz, 1983). It also provides an analogue to four of the five core processes of Project Management by positioning a self-action leader (an individual) as the ongoing “project” at hand. The SAL Model is rooted in action research and was developed through a variety of self-oriented, action research projects in conjunction with a comprehensive, qualitative, analytical autoethnographic study of a scholar’s life experiences.

Crosslinking of proteins for their irreversible immobilization on surfaces is a proven and popular method. However, many protocols lead to random orientation and the formation of undefined or even inactive by-products. Most concepts to obtain a more targeted conjugation or immobilization requires the recombinant modification of at least one binding partner, which is often impractical or prohibitively expensive. Here a novel method is presented, which is based on the chemical preactivation of Protein A or G with selected conventional crosslinkers. In a second step, the antibody is added, which is subsequently crosslinked in the Fc part. This leads to an oriented and covalent immobilization of the immunoglobulin with a very high yield. Protocols for Protein A and Protein G with murine and human IgG are presented. This method may be useful for the preparation of columns for affinity chromatography, immunoprecipitation, antibodies conjugated to magnetic particles, permanent and oriented immobilization of antibodies in biosensor systems, microarrays, microtitration plates or any other system, where the loss of antibodies needs to be avoided, and maximum binding capacity is desired. This method is directly applicable even to antibodies in crude cell culture supernatants, raw sera or protein-stabilized antibody preparations without any purification nor enrichment of the IgG. This new method delivered much higher signals as a traditional method and, hence, seems to be preferable in many applications.