In this paper we report the possibility of using the X-ray powder diffraction (XRPD) technique to detect the gamma-hydroxybutyric acid (GHB) as its sodium salt in different beverages but because it is not possible to freely buy them, beta-hydroxybutyric acid (BHB) and its sodium salt (NaBHB) were used as a model to fine tune an X-ray diffraction method for the qualitative analysis of the sodium salt of GHB. The method requires a small quantity of beverage, and an easy sample preparation, that consists only in the NaOH addition to the drink and a subsequent drying step. The dry residue obtained can be easily analyzed with XRPD using a single crystal X-ray diffractometer to exploit its high sensitivity that allows very fast patterns collection. Several beverages with different NaBHB:NaOH molar ratios were tested and the results show that NaBHB is detected in all drinks analyzed when NaBHB:NaOH molar ratio is 1:50 using characteristic peak at very low 2θ values that permits to detect its presence also in complex beverage matrices. Moreover, depending on the NaOH amount added, shifting and/or splitting of the characteristic peak of the NaBHB salt was observed, and the origin of this behavior was investigated.

Background and objective: Analysis of inflammatory biomarkers, along with the neutrophil/lymphocyte ratio (NLR) or platelets/lymphocyte ratio (PLR), supports the connection between inflammation and carcinogenesis. Methods: We conducted a retrospective observational study at the Clinical County Hospital Mureș, including patients with lung cancer. The parameters analyzed included: histopathological type (NSCLC - squamous cell carcinoma or adenocarcinoma; SCLC), molecular mutations (EGFR, ALK, PD-L1), parameters from the complete blood count, inflammatory parameters and associated comorbidities. Results: 380 patients were included: 115 patients in the cancer group and 265 patients in the control group. Among patients in the lung cancer group, 88 were diagnosed with NSCLC (44 adenocarcinomas, 44 squamous cell carcinomas) and 27 with SCLC. Both NLR and PLR were significantly higher in cancer patients than in the control group (5,30 versus 2,60, p<0,001; 217 versus 136, p< 0.001, respectively). NLR and PLR differs between men and women (p = 0.005, respectively p=0.056). C-reactive protein was not correlated with either NLR (p-value: 0.0669) or PLR (p-value: 0.6733) in lung cancer patients. Conclusion: The NLR and PLR values ​​may serve as new predictive biomarkers for the diagnostic of disease in patients with lung cancer, especially those with NSCLC.

We conducted a retrospective evaluation of the clinical outcomes and prognostic factors in patients with non-metastatic castration-resistant prostate cancer (nmCRPC) treated with first-line androgen receptor signaling inhibitors (ARSI) in real-world clinical practice in Japan. Between 2012 and 2023, a total of 127 consecutive patients with nmCRPC received ARSI treatment. Overall survival (OS), metastatic-free survival (MFS), and prostate-specific antigen progression–free survival (PSA-PFS) from ARSI initiation were assessed using Kaplan–Meier methodology. Clinical factors associated with OS in nmCRPC were analyzed using the Cox proportional hazards model. Among the patients, 72, 26, 12, and 17 received enzalutamide (ENZ), abiraterone (ABI), apalutamide (APA), and darolutamide (DARO) as first-line therapy. The median OS and MFS for all patients were 79.0 and 42.0 months, respectively. Median PSA-PFS was 27.0, 20.0, 10.0, and 14.0 months for patients treated with ENZ, ABI, APA, and DARO, respectively (p = 0.33). Multivariate analysis revealed that a baseline PSA level ≥3.67 ng/ml at ARSI initiation was significantly associated with poorer OS (p = 0.002). ARSI demonstrated favorable efficacy in nmCRPC patients. There were no significant differences in clinical outcomes among different types of ARSI therapy for nmCRP. Elevated baseline PSA at ARSI initiation was significantly associated with poorer OS.

Although the spanwise periodicity within the gap between two tandem circular cylinders has been observed by some researchers, there is a lack of systematic study on the properties of this pe-riodicity. For the spanwise periodicity within the gap, this study aims to ascertain its characteris-tics, its influences on the flow field, and its variation trend with increasing spacing ratio. By nu-merically simulating the flow around two tandem circular cylinders with a diameter ratio of d/D=0.6 and seventeen spacing ratios (L/D=1.00~6.00) at Re=3900, this study shows four flow re-gimes: Reattachment Flow (L/D=1.00~3.15), Bi-stable Flow (L/D=3.24), Intermittent Lock-in Co-shedding (L/D= 3.30~3.50) and Subharmonic Lock-in Co-shedding (L/D=4.00~6.00). Further, de-pending on the spanwise periodicity length of the time-averaged flow structures (i.e. Pz) within the gap, Reattachment Flow is, for the first time, subdivided into three new sub-flow regimes: Small-scale Periodic Reattachment (L/D=1.00~1.50, Pz/D=(0, 4]), Large-scale Periodic Reattachment (L/D=2.00~2.25, Pz/D>4) and Non-periodic Reattachment (L/D=2.50~3.15, no spanwise periodicity). The formation mechanisms are elaborated by analyzing the combined effect of both the L/D value and the spanwise-averaged time-averaged reattachment angle of the downstream cylinder. Moreover, this study proves that the newly-defined Small-scale Periodic Reattachment and Large-scale Periodic Reattachment are responsible for the pronounced asymmetry of the flow along the transverse direction within the gap. In addition, detailed flow properties and statistical pa-rameters are provided for each flow regime, such as velocity, vorticity, force coefficient, separa-tion/reattachment angle, Strouhal number and Q-criterion.

In this article the problem of detection and isolation (FDI) in wheeled mobile robot is 1 treated. first of all we consider a master-slave robot system in which the master robot has to follow a 2 desired trajectory given by a well-determined control law, then the slave is controlled by the master. 3 However in real environment there is no ideality because faults can appear in the master or slave 4 or even the both and affect the system and may lead to unacceptable results so to ensure a well 5 functioning an extended kalman filter is tuned to diagnosis eventual faults and to generate residuals 6 in order to detect and isolate them. The performance of an estimator based on an EKF is simulated 7 based MATLAB Simulink simulations.

The response of building elements during earthquakes has been an area of concern for different researchers around the world. The NSEs are the first elements to attain failure, the buildings after damages in safety priority are classified as in “Life Safety” mode, but in reality, they are in “Collapse Safety” mode and the occupants inside the buildings are in a state of “Non-Life Safety” as a result of falling of the hazardous NSE’s like cladding's, partitions, hanging objects. In addition to the Life Cycle Cost Assessment (LCCA), the Social Life Cycle Assessment (SLCA) is overlooked by the majority of the researchers, the community must be prepared to respond to an event more efficiently without any major casualties or loss of life. It is expected that by the end of 2050, almost double the construction will take place, the embodied energy during the pre-construction, post-construction and demolition generates a lot of CO2s into the environment, hence sustainability should be given due importance, helping in the achievement of Sustainable Developmental Goals (SDGs).

Respiratory viral infections (RVI) are common reasons for healthcare consultations. The inpatient management of RVI consumes significant resources. From 2009-2014, we assessed the costs of RVI management in 4776 hospitalized chil-dren aged 0-18 years participating in a quality improvement program, where all ILI patients underwent virologic testing at the National Reference Centre followed by de-tailed recording of their clinical course. The direct (medical or non-medical) and indirect costs of inpatient management outside the ICU (“non-ICU”) versus management requiring ICU-care (“ICU”) added up to 2,767.14€ (non-ICU) vs. 29,941.71€ (ICU) for Influenza, 2,713.14€ (non-ICU) vs. 16,951.06€ (ICU) for RSV infections, and 2,767.33€ (non-ICU) vs. 14,394.02€ (ICU) for human rhinovirus (hRV) infections, respectively. Non-ICU inpatient costs were similar for all 8 RVI studied: Influenza, RSV, hRV, ade-novirus (hAdV), metapneumovirus (hMPV), parainfluenzavirus (hPIV), bocavirus (hBoV) and seasonal coronavirus (hCoV) infections. ICU-costs for Influenza however, ex-ceeded all other RVI. At the time of the study, Influenza was the only RVI with antivi-ral treatment options available for children, but only 9.8% of Influenza patients (non-ICU) and 1.5% of ICU-patients with Influenza received antivirals; only 2.9% were vac-cinated. Future studies should investigate the economic impact of treatment and pre-vention of Influenza-, COVID-19-, and RSV post vaccine introduction.

(1) Background: Prevention of acute cardiovascular events in patients with cardiovascular diseases (CVDs) requires promoting health-protective behaviors (e.g., physical activity) and preventing health-compromising behaviors (sitting). Digital health interventions provide much potential. Based on multiple behavioral change theory, an intervention (reCardial app) was evaluated, and the following hypotheses were tested: H1: Health behaviors (physical activity, sitting) and disease self-management (self-care maintenance, self-care confidence) are closely interrelated. H2: Change in health behaviors and disease self-management indicators over time is more pronounced in reCardial app-users. H3: In the intervention group, changes in systolic and diastolic blood pressure indicate a positive trajectory. (2) Methods: A study with the design of a randomized controlled trial over 12 weeks was conducted. 40 CVD-patients were randomized equally to the Intervention Group (35% women; Mage=60.6years) and Control Group (45% women; Mage=61.5years). (3) Results: Findings support H1 with significant correlations between health behaviors (r=0.45-0.63**), and disease self-management (r=-0.32-0.54**), H2 with Eta²=0.21 (not statistically significant) and H3 partially with d=0.101 for systolic blood pressure but not regarding diastolic blood pressure. (4) Conclusions: Replications are needed with larger samples and more objective measures. The app can help prevent and manage CVD by means of promoting health-protective behaviors and preventing health-compromising behaviors. Taking different behaviors into account can increase intervention effects and with that support of users.

Objetives: Adequate donor-recipient matching is necessary to achieve the best renal function after transplantation. The nephron load received from the donor, which can be reflected in variables such as age, sex and body mass index, may influence the evolution of the graft. Our objetive was develop a combined score according to the donor-recipient pairing in age, sex and body mass index, and assess its influence on the evolution of the renal graft. Materials and methods: Transplant patients between 2013 and 2020 who had at least 1 year of post-transplant follow-up. A ranking of 0 to 2 points was awarded according to the match between donor and recipient for sex, age and body mass index individually, with higher rank to greater mismatch. Subsequently, a Score with value of 0 to 6 points was created with the combined ranking of the indivudual variables, analyzing its influence on the evolution of the graft by multivariate linear regression. Results: 280 patients followed for 4.3 years of median. Worse renal function was observed at the end of follow-up as the range of each variable increased separately, and the Score created, with a worsening of renal function as the combined Score increased in the multivariate analysis: Coefficient B= -2.4 ml/min, p=0.018. Conclusions: An adequate match between donor and recipient in age, sex and body mass index using this combined Score can help achieve better kidney function after transplantation.

Diabetes mellitus is a widespread chronic metabolic disorder demanding regular blood glucose level surveillance (BGLs). Current invasive techniques, such as finger-prick tests, often result in discomfort for patients, leading to infrequent monitoring and potential health complications. The primary objective of this study was to design a novel, portable, non-invasive system for diabetes detection using breath samples, named as DiabeticSense, an affordable digital health device for early detection, encouraging immediate intervention. The device employed MOSFET-based electrochemical sensors to assess volatile organic compounds in breath samples, whose concentrations differ between diabetic and non-diabetic individuals. The system merged body vital signs with sensor voltages obtained by processing breath sample data to predict diabetic conditions. Our research used readings from 100 patients at a nationally recognised hospital to form the dataset. Data was then processed 10 using a Gradient Boosting Classifier model, and performance was cross-validated. The proposed system attained a promising accuracy of 86.6%, marking an improvement of 20.72% over an existing regression technique. The developed device introduces a non-invasive, cost-effective, and user-friendly solution for preliminary diabetes detection. It has the potential to increase patient adherence to regular monitoring.

For many years, energy monitoring at the most disaggregate level has been mainly sought through the idea of Non-Intrusive Load Monitoring (NILM). Nevertheless, a practical application of this concept in the residential sector should address the underlying concerns raised by the technical specifications of case studies. From one side, such an operation must handle common matters related to the essence of any NILM system. Although this aspect has been thoroughly investigated by basic research, it is limited to the properties of public datasets. On the other side, it must deal with specific concerns corresponding to uncommon situations. These circumstances impose further restrictions on existent NILM schemes, however, they have been overlooked due to the lack of pertinent databases to scrutinize. Accordingly, this paper presents applied research on a potential solution to NILM for Quebec residences. It carries out a relevant investigation into the multi-faceted nature of this problem in order to reveal barriers to feasible implementations in the context of Quebec. This work commences with a concise discussion about the NILM idea to highlight its essential requirements for a fruitful practice. Afterward, it provides a comparative statistical analysis to represent the specificity and potential challenges of the case study in accordance with NILM necessities. For this purpose, the examination exploits data from real-world measurement systems in the same and European regions. Subsequently, this study focuses on a load identification exercise by proposing a combinatory approach that utilizes the promise of sub-meter smart technologies to integrate the intrusive aspect of load monitoring with the non-intrusive one. The former is aimed at extracting overall heating demand from the aggregate one by a supervised procedure based on Deep Learning (DL) models while the latter is designed for disaggregating the residual load through an unsupervised process on the basis of clustering techniques. The results demonstrate that geographically-dependent cases create electricity consumption scenarios under which existing NILM methods can be questioned. From a realistic standpoint, this research elaborates on critical remarks to realize viable NILM systems, particularly, in Quebec houses.

The approach based on molecular modeling was developed to study dNTP derivatives characterized by new polymerase-specific properties. For this purpose, the relative efficiency of PCR amplification with modified dUTPs was studied using Taq, Tth, Pfu, Vent, Deep Vent, Vent (exo-), and Deep Vent (exo-) DNA polymerases. The efficiency of PCR amplification with modified dUTPs was compared with the results of molecular modeling using the known 3D structures of KlenTaq polymerase–DNA–dNTP complexes. The dUTPs were C5-modified with bulky functional groups (the Cy5 dye analogs) or lighter aromatic groups. Comparing the experimental data and the results of molecular modeling revealed the decrease of PCR efficiency in the presence of modified dUTPs with an increase in the number of non-covalent bonds between the substituents and the DNA polymerase (about 15% decrease per one extra non-covalent bond). Generalization of the revealed patterns to all the studied polymerases of the A and B families is discussed herein. The number of non-covalent bonds between the substituents and polymerase amino acid residues is proposed to be a potentially variable parameter for regulating enzyme activity.

Electrochemical Promotion was used to modify the activity and selectivity of a Rh catalyst-electrode in the CO2 hydrogenation reaction. The experiments were carried out in a temperature range of 350-430οC at ambient pressure and at different CO2 to H2 gas feeding ratios (1:2 to 4:1). The only reaction products observed were CO and CH4, both under open and closed-circuit conditions. The CH4 formation rate was found to increase with both positive and negative potential or current application. The CO formation rate followed the opposite trend. The selectivity to CH4 increased under high values of hydrogen partial pressure and decreased at high pressures of CO2. The results demonstrate how Electrochemical Promotion can be used to finely tune activity and selectivity for a reaction of high technical and environmental importance.

In the context of autosomal dominant polycystic kidney disease (ADPKD), total kidney volume (TKV) plays a key role as biomarker of disease progression and response to therapy and has been recently recognized as enrichment biomarker and possible surrogate endpoint. Several imaging modalities and methods are available to calculate TKV, and the choice depends on the purpose of use. Technological advancements have made it possible to accurately assess cyst burden, that can be crucial to assess the disease state and help identifying rapid progressors. Moreover, the development of automated algorithms has increased the efficiency of total kidney and cyst volume measurements. Beyond total kidney and cyst volume, the quantification and characterization of non-cystic kidney tissue show potential to early stratify ADPKD patients, monitor disease progression, and possibly predict renal function loss. A broad spectrum of kid-ney MRI techniques are available to characterize kidney tissue, showing promise to non-invasively pick up early signs of ADPKD progression. Radiomics has been used to extract tex-tural features from ADPKD images, providing valuable information about the heterogeneity of the cystic and non-cystic components. This review provides an overview of ADPKD imaging bi-omarkers, focusing on quantification methods, potential, and necessary steps towards successful translation to clinical practice.

Laser energy per unit surface, necessary to trigger the material removal, decreases with the pulse shortening becoming the pulse-time independent in the sub-picosecond range. These pulses are shorter the electron-to-ion energy transfer time and electronic heat conduction time minimizing the energy losses. The electrons receiving the energy larger than the threshold, drag the ions off the surface in the mode of electrostatic ablation. We show that the pulse shorter than the ion period (Shorter-the-Limit (StL)) ejects conduction electrons with the energy larger than the work function (from a metal) leaving the bare ions immobile in a few atomic layers. The electrons emission is followed by the bare ion’s explosion, ablation, and THz radiation from expanding plasma. We compare this phenomenon to the classic photo effect, nanocluster Coulomb explosions, show differences and consider possibilities for detecting the new mode of ablation experimentally by emitted THz radiation and consider applications of high-precision nano-machining with this low intensity irradiation.

We find at least 4 quantum properties that are indeed universal in some number systems; and we can use them for quantum consciousness. Using the sets B={0,1}, N, Z, or Q has the +4 quantum properties that one can trust, as archetypes of easy communication to friends and foes, to ignoranti or cognoscenti, and for quantum computing. This paper proposes the use of Bayesian geometry to reduce the space of possible results, reducing or increasing initial beliefs by successive experimentation. This is exemplified in biology and mathematics, and can be applied to physics and other sciences. The conclusion is that an experimental fact can be absolutely verified. Any mathematical choice (as verified by computers) militating against R=Q, is under an absolutely low chance to succeed. Infinitesimals are denied based on 3^16 independent factors. This is not a probabilistic result, but based on reduction of the Bayes geometry for updating beliefs. This work applies to non-probabilistic and unknown phenomena, such as those found in oscillations (neutrino, health), evolution, and quantum computing, denies Gödel's uncertainty, and solves the liar's paradox by reflection. This connects different scientific fields with one another, in an internet, i.e., in a network of connections of multiple open networks, using the set Q, resembling a hologram, and includes entanglement.

Numerous dynamic and complicated processes characterize development from the oocyte to the embryo. However, given the importance of functional transcriptome profiles, long non-coding RNAs, single-nucleotide polymorphisms, and alternative splicing during embryonic development, the effect that these features have on the blastomeres of 2-, 4-, 8-, 16-cell, and morula stages of development have not been studied. Here, we conducted a scRNA-seq survey of cells from sheep from the oocyte to the blastocyst developmental stages. We then carried out experiments to identify and functionally analyze the transcriptome profiles, long non-coding RNAs, single-nucleotide polymorphisms (SNPs), and alternative splicing (AS). We founded that between the oocyte and zygote groups significantly down-regulated genes and the second-largest change in gene expression occurred between the 8- and 16-cell stages. We used various methods to construct a profile to characterize cellular and molecular features and systematically analyze the related GO and KEGG profile of cells of all stages from the oocyte to the blastocyst. This large-scale, single-cell atlas provides key cellular information and will likely assist clinical studies in improving preimplantation genetic diagnosis.

Cyanobacteria produce a wide range of structurally diverse cyanotoxins and bioactive cyanopeptides in freshwater, marine, and terrestrial ecosystems. The health significance of these metabolites, which include genotoxic- and neurotoxic agents, is confirmed by continued associations between the occurrence of animal and human acute toxic events and, in the long term, by associations between cyanobacteria and neurodegenerative diseases. One of the implicated mechanisms includes a misincorporation of cyanobacterial non-proteogenic amino acids leading to mistranslation and protein misfolding. A better understanding of the interaction between the cyanopeptide metabolism and the nervous system will be crucial to target or to prevent pathogenic response.

Lung cancer is a common malignant tumor of the lung and the leading cause of cancer mortality worldwide. Non-small-cell lung cancer (NSCLC) accounts for 80%–85% of lung cancer, 40% of NSCLCs will have spread beyond the lungs by the time it is diagnosed. Long non-coding RNA (LncRNA) prostate androgen-regulated transcript 1 (PART-1) was reported that promote the development of several cancers. In the current study, we conducted experiments to investigate the role of PART-1 in the proliferation, invasion, and migration of NSCLC. The expression level of the PART-1 gene increased significantly in the NSCLC cell lines, including A549, H1229, H1650, H1975, and PC9. Knocking down of PART-1 inhibited the proliferation, invasion, and migration of A549 cells, moreover, decreased the tumor proliferation in nude mice. We confirmed that PART-1 targeted miR-204-3p directly, and miR-204-3p targeted the insulin-like growth factor binding protein 2 (IGFBP-2) directly. Furthermore, we discovered that PART-1 involved the NSCLC progression by regulating the miR-204-3p-targeted IGFBP-2 pathway. LncRNA PART-1 might be a target for treating NSCLC, and a warning sign of diagnosis of early lung cancer.

This paper presents an approach to the vibration analysis of axially functionally graded (AFG) non-prismatic Euler-Bernoulli beams using the finite difference method (FDM). The characteristics (cross-sectional area, moment of inertia, elastic moduli, and mass density) of AFG beams vary along the longitudinal axis. The FDM is an approximate method for solving problems described with differential equations. It does not involve solving differential equations; equations are formulated with values at selected points of the structure. In addition, the boundary conditions and not the governing equations are applied at the beam’s ends. In this paper, differential equations were formulated with finite differences, and additional points were introduced at the beam’s ends and at positions of discontinuity (supports, hinges, springs, concentrated mass, spring-mass system, etc.). The introduction of additional points allowed us to apply the governing equations at the beam’s ends and to satisfy the boundary and continuity conditions. Moreover, grid points with variable spacing were also considered, the grid being uniform within beam segments. Vibration analysis of AFG non-prismatic Euler-Bernoulli beams was conducted with this model, and natural frequencies were determined. Finally, a direct time integration method (DTIM) was presented. The FDM-based DTIM enabled the analysis of forced vibration of AFG non-prismatic Euler-Bernoulli beams, considering the damping. The results obtained in this paper showed good agreement with those of other studies, and the accuracy was always increased through a grid refinement.

Lung cancer is the most common malignancy across the world. The new era in lung cancer treatments, especially this past decade, has yielded novel categories of targeted therapy for specific mutations and adjuvant therapy, both of which have led to improved survival rates. In the present study, we review the changes and development of treatments, with a special focus on adjuvant therapy using tyrosine kinase inhibitors (TKIs) administered to non-small-cell lung carcinoma patients who had a complete resection of the tumor harboring a mutated epidermal growth factor receptor. The clinical trials are dating from the past (chemotherapy trials), present (TKIs) and future (ongoing trials).

Among non-conventional yeasts of industrial interest, the dimorphic oleaginous yeast Yarrowia lipolytica appears as one of the most attractive for a large range of white biotechnology applications, from heterologous proteins secretion to cell factories process development. The past, present and potential applications of wild type, traditionally improved or genetically modified Yarrowia lipolytica strains will be resumed, together with the wide array of molecular tools now available to genetically engineer and metabolically remodel this yeast. The present review will also provide a detailed description of Yarrowia lipolytica strains and highlight the natural biodiversity of this yeast, a subject little touched upon in most previous reviews. This work intends to fill this gap by retracing the genealogy of the main Yarrowia lipolytica strains of industrial interest, by illustrating the search for new genetic backgrounds and by providing data about the main publicly available strains in yeast collections worldwide. At last, it will focus on exemplifying how advances in engineering tools can leverage a better biotechnological exploitation of the natural biodiversity of Yarrowia lipolytica and of other yeasts from the Yarrowia clade.

In this work the existence and nonexistence of stationary radial solutions to the elliptic partial differential equation arising in the molecular beam epitaxy are studied. Since we are interested in radial solutions we arrive at the following fourth-order differential equation

The preservation of the authenticity of a building artefact is a responsible practice. On the other side, the need to save the building artefact from the natural and anthropic degradation, to ensure the structural reliability to the different actions, to define an efficient maintenance program are big challenges, that involves the cooperation of several professionals, responsible use of innovative techniques and materials that are nowadays available. This paper focuses on a specific design approach for the rehabilitation works of ancient constructions in archaeological sites. The proposed conceptual design approach implies different steps that allow the optimization of the design at an increasing level of knowledge on the existing structures and their materials. The design procedure on historical constructions generally includes the following steps: the collection of data, the structural identification, hazard, and vulnerability analysis, damage and risk analysis, a cost-benefit analysis, so only at the end of the process, the final design is achieved. In the archaeological area, some important design aspects cannot be defined before the execution work phase, since some elements could be revealed and identified during work execution, as a consequence, the final design has been often optimized after all this information has been acquired. A studied case in the archaeological site of Pompeii is herein presented to prove the efficiency of the proposed approach.

This paper deals with a non-standard finite difference scheme defined on a quasi-uniform mesh for approximate solutions of the Magneto-Hydro Dynamics (MHD) boundary layer flow of an incompressible fluid past a flat plate for a wide range of the magnetic parameter. We show how to improve the obtained numerical results via a mesh refinement and a Richardson extrapolation. The obtained numerical results are favourably compared with those available in the literature.

Background: Objectives. The objective of this study was to compare the efficacy of direct current stimulation (DCS) applied at the transcranial, suboccipital and spinal level on experimental sensory modalities and pain outcome measures in healthy subjects. The hypothesis of this study was that systematic analysis of the efficacy of DCS on modulating evoked thermal and mechanical pain modalities and mechanisms such as endogenous pain modulation in healthy individuals would reveal sensitive outcome measures help develop this technique for the control of chronic pain. Materials and Methods. Database searches were conducted up to December 2019 for randomized controlled trials that performed sham-controlled DCS of experimental sensory modalities and pain outcomes following transcranial, suboccipital and spinal locations in healthy participants. Standardized mean differences with 95% confidence intervals were calculated for sensory modalities, including random-effect metanalysis. Results: Thirty-one studies were included for analysis (647 participants). A significant decrease in pain intensity for active vs sham transcranial stimulation was identified for pain intensity (n=158; SMD=0.79; 95% CI=0.56 to 1.02), a significant increase in heat pain threshold (n=222; SMD=1.16; 95% CI=0.95 to 1.37), and a significant increase in cold pain threshold (n = 155; SMD = 0.77, 95% CI 0.53 to 1.01). No significant modulation of pressure pain threshold was identified with DCS and only a limited number of studies focused on experimental pain modulation following neuromodulation at the suboccipital or spinal level. Conclusions: These results show significant transcranial DCS neuromodulation of pain intensity and on thermal pain modalities. Future studies should focus on endogenous pain and sensory modality modulation with sham-controlled DCS applied at transcranial, suboccipital and spinal locations.

Biological systems are highly regulated. They are also highly resistant to sudden perturbations enabling them to maintain the dynamic equilibrium essential for sustenance of life. This robustness is conferred by regulatory mechanisms that influence the activity of enzymes/proteins within their cellular context, to adapt to changing environmental conditions. However, the initial rules governing the study of enzyme kinetics were tested and implemented for mostly cytosolic enzyme systems that were easy to isolate and/or recombinantly express. Moreover, these enzymes lacked complex regulatory modalities. Now, with academic labs and pharmaceutical companies turning their attention to more complex systems (for instance, multi-protein complexes, oligomeric assemblies, membrane proteins and post-translationally modified proteins), the initial axioms defined by Michaelis-Menten (MM) kinetics are rendered inadequate and the development of a new kind of kinetic analysis to study these systems is required. The current review strives to present an overview of enzyme kinetic mechanisms that are atypical and, oftentimes, do not conform to the classical MM kinetics. Further, it presents initial ideas on the design and analysis of experiments in early drug-discovery for such systems, to enable effective screening and characterisation of small-molecule inhibitors with desirable physiological outcomes.

Bacterial infections occur when wound healing fails to reach the final stage of healing, usually hindered by the presence of different pathogens. Different topical antimicrobial agents are used to inhibit bacterial growth due to antibiotic failure in reaching the infected site accompanied very often by an increased drug resistance and other side effects. In this review, we focus on antimicrobial peptides (AMPs), especially those with a high potential of efficacy against multidrug-resistant and biofilm-forming bacteria and fungi present in wound infections. Currently, different AMPs undergo preclinical and clinical phase to combat infection-related diseases. AMP dendrimers (AMPDs) have been mentioned as potent microbial agents. Various AMP delivery strategies, such as polymers, scaffolds, films and wound dressings, organic and inorganic nanoparticles, to combat infection and modulate the healing rate have been discussed as well. New technologies such as CRISPR-Cas are taken into consideration as potential future tools for AMP delivery in skin therapy.

Crop type and field boundary mapping enable cost-efficient crop management on the field scale and serve as the basis for yield forecasts. Our study uses a data set with crop types and corresponding field borders from the federal state of Bavaria, Germany, as documented by farmers from 2016 to 2018. The study classified corn, winter wheat, barley, sugar beet, potato, and rapeseed as the main crops grown in Upper Bavaria. Corresponding Sentinel-2 data sets include the normalised difference vegetation index (NDVI) and raw band data from 2016 to 2018 for each selected field. The influences of clouds, raw bands, and NDVI on crop type classification are analysed, and the classification algorithms, i.e., support vector machine (SVM) and random forest (RF), are compared. Field boundary detection and extraction are based on non-iterative clustering and a newly developed procedure based on Canny edge detection. The results emphasise the application of Sentinel’s raw bands (B1–B12) and RF, which outperforms SVM with an accuracy of up to 94%. Furthermore, we forecast data for an unknown year, which slightly reduces the classification accuracy. The results demonstrate the usefulness of the proof-of-concept and its readiness for use in real applications.

Phylogenomics, the use of large datasets to examine phylogeny, has revolutionized the study of evolutionary relationships. However, genome-scale data have not been able to resolve all relationships in the tree of life; this could reflect, at least in part, the poor-fit of the models used to analyze heterogeneous datasets. Some of the heterogeneity may reflect the different patterns of selection on proteins based on their structures. To test that hypothesis, we developed a pipeline to divide phylogenomic protein datasets into subsets based on secondary structure and relative solvent accessibility. We then tested whether amino acids in different structural environments had distinct signals for the topology of the deepest branches in the metazoan tree. The most striking difference in phylogenetic signal reflected relative solvent accessibility; analyses of exposed sites (on the surface of proteins) yielded a tree that placed ctenophores sister to all other animals whereas sites buried inside proteins yielded a tree with a sponge-ctenophore clade. These differences in phylogenetic signal were not ameliorated when we repeated our analyses using the CAT model, a mixture model that is often used for analyses of protein datasets. In fact, the heterogeneous CAT model resulted in several rearrangements that are unlikely to represent evolutionary history. However, analyses conducted after recoding amino acids to limit the impact of deviations from compositional stationarity increased the congruence in the estimates of phylogeny for exposed and buried sites; after recoding amino acids both trees supported placement of ctenophores sister to all other animals. These results provide striking evidence that it is necessary to achieve a better understanding of the constraints due to protein structure to improve phylogenetic estimation.

Paenibacillus sp. tmac-D7 was isolated from coastline growing Trifolium macraei (double-head clover) root nodules from Bodega Bay, California. The draft genome is 5,567,337 bp with a G+C% of 52.4%, an N50 of 114,261 bp, and 5,282 predicted protein-coding genes. Paenibacillus, while found in many other environments, is frequently isolated from root nodules, with many acting as plant pathogen antagonists. Paenibacillus sp. tmac-D7 is the first genome of a non-rhizobial endophyte isolate from wild Trifolium macraei (double-head clover).

This paper discusses a cross-disciplinary, international collaboration aimed at researching a series of 15th century choir books at the abbey of San Giorgio Maggiore on the homonymous island in Venice. Produced for the abbey itself, the books have never left the island during their 500-years history, thereby allowing a unique opportunity to analyse historic artefacts, which have undergone little modification over time. Prompted by ongoing cataloguing work on the manuscripts, a week-long analytical campaign using a combination of non-invasive analytical methods used in portable configuration allowed the comprehensive characterisation of ten volumes. The manuscripts’ palette and painting techniques were analysed using near-infrared imaging, reflectance spectroscopy in the UV-vis-NIR range, Raman spectroscopy, X-ray fluorescence mapping and digital microscopy. The paper will discuss the challenges linked to the fragility and the large dimensions of the volumes as well as the most interesting results of the investigation. These include the detection of unusual painting materials such as bismuth ink, as well as the discovery of a less homogeneous palette than originally expected, which prompted a partial revision of the attribution of the decoration in one of the volumes to a single artist.

Background and objectives: The initiation of apoptotic death in cancer cells is the aim of many chemotherapeutic strategies. As many anticancer agents have been discovered in natural plant sources, the search for novel phytochemicals displaying anticancer activities continues at a tremendous rate. This study was conducted to evaluate the effect of extractable polyphenols (EPP); non-extractable polyphenols (NEPP); nobiletin (NOB); tectorigenin (TEC) and persicogenin (PERS) from Barhi date palm kernels (BDPK) extracts on the induction of apoptosis in human lung cancer A549 and colon cancer HT29 cell lines. Materials and Methods: The anticancer activities were determined using MTT and trypan blue exclusion assays. Flow cytometry analysis was performed to study the cell viability, cell cycle arrest and apoptosis. The underlying mechanism of apoptosis induced by crude extracts and the purified compounds was investigated using caspase-3, -8 and -9 assays and the mitochondrial membrane potential assay. Results: The findings indicate that both BDPK extracts and the purified compounds do exert induced cell death on A549 and HT29 cells. The results observed from MTT- assay and trypan blue exclusion indicate that the cytotoxic effects of both plant extracts and the three isolated flavonoids are dose-dependent with higher cell death after 72 hours treatment. Treatment of human lung and colon cancer cells with EPP, NEPP, NOB, TEC and PERSI induced late stages of apoptosis as there was evidence of the DNA degradation and high percentage of the cells population was situated at sub-G1 phase, indicating a high population of apoptotic cells. Conclusions: Study of the apoptotic mechanism demonstrated that EPP and NEPP exhibited dependent mitochondrial signalling pathway as seen with caspase-9 and induced receptor-mediated (extrinsic) apoptotic pathway as seen with caspase-8. Therefore, our results suggest that BDPK extracts and the three isolated flavonoids could be a good candidate for developing anticancer agents.

External quantum efficiency of industrial-grade green InGaN light-emitting diodes (LEDs) has been measured in a wide range of operating currents at various temperatures from 13 K to 300 K. Unlike blue LEDs, the efficiency as a function of current is found to have a multi-peak character, which could not be fitted by a simple ABC-model. This observation correlated with splitting of LED emission spectra into two peaks at certain currents. The characterization data are interpreted in terms of non-uniformity of the LED active region, which is tentatively attributed to extended defects like V-pits. We suggest a new approach to evaluation of temperature-dependent light extraction and internal quantum efficiencies taking into account the active region non-uniformity. As a result, the temperature dependence of light extraction and internal quantum efficiencies have been evaluated in the temperature range mentioned above and compared with those of blue LEDs.

This study purposes the use of plug-in electric vehicles for demand side management (DSM) considering uncertainties in demand as well as uncertainties due to mobility of PEV to mitigate peak demand. The solution also seeks to reduce electric cost in addition to reducing the effects of greenhouse gases. In recent years DSM using distributed storage system such as battery energy management system (BESS) and plugged-in electric vehicles (PEV) have become very prevalent with most implementations resorting to deterministic load forecast. These methods do not consider the potential growth in demand making their solutions less robust. In this study we propose a real-time density demand forecast and stochastic optimization for robust operation of PEV for a building. This method accounts for demand uncertainties in addition to uncertainties in mobile energy storage as found in PEV, making the resulting solution robust as compared to the deterministic case. A case study on a real site in South Korea is used for verification and testing. The proposed study is verified and tested against existing algorithms. The result verifies the effectiveness of the proposed approach

Supplementing essential amino acids (EAA), without considering non-EAA (NEAA) and energy contents in reduced crude protein (CP) diets may alter essential-to-total AA or true protein (E:T) and energy-to-protein ratios, potentially compromising growth. This study aimed to evaluate the effects of CP, E:T and net energy (NE) on broiler performance. Treatments were: T1— reduced CP (16%, RP), low NE (9.9 MJ/kg, LNE), low E:T (0.56, LE:T); T2—RP, LNE, high E:T (0.60, HE:T), with imbalanced EAA (excess Met and deficient Thr); T3—RP, high NE (10.4 MJ/kg, HNE), LE:T; T4—RP, HNE, HE:T; T5— normal CP (18%, NP), LNE, LE:T; T6—NP, LNE, HE:T; T7—NP, HNE, LE:T; and T8—NP, HNE, HE:T. The study employed as-hatched Cobb 500 broilers in two experiments. Exp.1 studied performance from d19 to 35, with 8 replicates per treatment and 16 birds per replicate (n=1024). Exp.2 measured NE values in respiration chambers from d25 to 28, with 6 replicates per treatment, and 2 birds (a male and a female) per replicate (n=96). The measured NE values were used to calculate NE intake (NEi) in Exp.1. The results showed that T4 improved (P < 0.001) weight gain (WG), feed conversion ratio (FCR), and NEi relative to T1, T2 and T3, and protein efficiency (WG/CP intake) relative to all treatments. The live performance (feed intake, WG, FCR) and NEi of birds fed T4 reached a level equal to those of birds fed NP-diets (T5 to T8). These results suggest that a dietary E:T ratio of 0.60 is necessary to maximize nutrient utilization and to restore growth rate in broilers fed RP-diets.

Ultrasonic additive manufacturing (UAM) is a process for three-dimensional printing of metal foil stock that can produce near-net shape metallic parts. This work details the development of an energy-based tool to identify relationships between input energy, stored energy in the interface microstructure, and the strength of the weld interface in UAM. The stored energy in the grain boundaries of the crystallized grains in the interface microstructure are estimated using the Read-Shockley relationship. The energy stored in the interface is found to be positively correlated with the resulting weld strength. An energy flow diagram is developed to map the flow of energy from the welder to the workpiece and quantify the key participating energies such as the energy of plastic deformation, energy stored in the interface microstructure, energy required for asperity collapse, and heat generation. A better understanding of the flow of energy in UAM can assist in optimizing the process to maximize the portion of input energy from the welder that is used for bond formation.

Reliable prediction of building-level energy demand is crucial for the building managers to optimize and regulate energy consumption. Conventional prediction models omit the uncertainties associated with demand over time; hence, they are mostly inaccurate and unreliable. In this study, a Bayesian neural network (BNN)-based probabilistic prediction model is proposed to tackle this challenge. By quantifying the uncertainty, BNNs provide probabilistic predictions that capture the variations in the energy demand. The proposed model is trained and evaluated on a subset of the building operations dataset of Lawrence Berkeley National Laboratory (LBNL), Berkeley, California, which includes diverse attributes related to climate and key building performance indicators. We have performed thorough hyperparameter tuning and used fixed-horizon validation to evaluate trained models on various test data to assess generalization ability. To validate the results, quantile random forest (QRF) was used as a benchmark. The study compared BNN with LSTM, showing that BNN outperformed LSTM in uncertainty quantification.

Modern methods of designing and constructing hydraulic pumps can no longer be imagined without the use of appropriate mathematical models, phenomena and processes that take place in concrete constructions. A mathematical model of a process represents an analytical interpretation with certain assumptions. Obtaining a mathematical model requires detailed theoretical research, based on knowledge of the laws of fundamental sciences and scientific disciplines in order to fully understand and interpret the process, based on which assumptions are adopted and model equations are defined. As mobile machines continue to evolve, so do the demands on their hydraulic systems. Efficiency, automation and other major industry trends present ongoing development opportunities for hydraulic systems used in mobile applications. Hydraulic systems remain an important component in a range of mobile applications, from construction and agricultural equipment to heavy trucks because of the power density they can provide for a range of work functions. The power density of hydraulics remains unmatched in many applications. The pump, as an essential hydraulic component, converts mechanical energy into hydraulic energy with a relatively small amount and speed of fluid.

In this paper, we propose a novel stochastic model to study prime distribution in almost-short intervals, inspired by a corollary of the Maynard-Guth theorem. The model uses the equation \[ x_{n+1} = x_n + \frac{y}{\log x_n} + \epsilon_n, \] where \(\epsilon_n\) follows a Laplace distribution, and demonstrates that our new bound surpasses both Walfisz and Maynard-Guth bounds, particularly for large \(x\): \[ \left| \pi(x + y) - \pi(x) - \frac{y}{\log x} \right| \leq C \cdot y \exp(-\sqrt[4]{\log x}). \] Additionally, we explore a modulated Hamiltonian \(\hat{H}(x)\), derived from a potential \(V(x)\) and a test function \(f(x)\), that exhibits behavior akin to the energy levels of the heavy nucleus \(H_{38}\). The gaps between these energy levels resemble the distribution of zeros of the Riemann zeta function near the critical line, suggesting that \(\zeta(0.5 + i \hat{H}(x))\) corresponds to the energy levels of \(\hat{H}(x)\), thus supporting a quantum mechanical interpretation of the Riemann hypothesis. Furthermore, assuming the Elliott-Halberstam conjecture, which implies that prime gaps can be as small as 12, we find that the transition rate \(\Gamma_{p \to p+12}\) between quantum states associated with prime numbers increases with larger primes. This observation indicates that the distribution of prime gaps reflects an underlying discrete structure in the "energy" landscape of primes, offering a novel perspective on the connection between number theory and quantum physics.

Alena Tensor is a recently discovered class of energy-momentum tensors that provides mathematical framework in which, as demonstrated in previous publications, the description of a physical system in curved spacetime and its description in flat spacetime with fields are equivalent. The description of a system with electromagnetic field based on Alena Tensor can be used to reconcile physical descriptions. 1) In curvilinear description, Einstein Field Equations were obtained with Cosmological Constant related to the invariant of the electromagnetic field tensor, which can be interpreted as negative pressure of vacuum, filled with electromagnetic field. 2) In classical description for flat spacetime, three densities of four-forces were obtained: electromagnetic, gravity, and the force responsible for the Abraham-Lorentz effect (radiation reaction force). Obtained connection of Einstein tensor with gravity and radiation reaction force, after transition to curvilinear description, excludes black hole singularities. There was obtained Lagrangian density and generalized canonical four-momentum, containing electromagnetic four-potential and a term responsible for other two forces. In this description charged particles cannot remain at complete rest and should have spin, their energy results from the existence of the energy of the magnetic moment and the density of this energy is part of the Poyting four-vector. The distribution of charged matter was expressed as polarization-magnetization stress-energy tensor, what may explain why gravity is invisible in QED. 3) In quantum picture, QED Lagrangian density simplification was obtained, and the Dirac, Schrödinger and Klein-Gordon equations may be considered as approximations of the obtained quantum solution. Farther use of Alena Tensor in unification applications was also discussed.

This study explores the impact mechanism of the service-oriented transformation of new energy enterprises on the satisfaction of employee performance evaluation systems under the background of China's electricity market reform. Using CGN New Energy's Guangxi branch as a case study, and adopting the grounded theory method, this research systematically analyzes the influencing factors and action paths of the service-oriented transformation on the satisfaction of employee performance evaluation systems through in-depth interviews and questionnaires. The study finds that the service-oriented transformation significantly enhances employees' sense of professional achievement and skill levels but also increases work pressure and psychological burden. Optimizing the performance evaluation system and improving its fairness and transparency are key to enhancing employee satisfaction. The research results provide a scientific basis for the management practices of new energy enterprises and hold significant reference value for relevant policy-making.

Background/objective: Tools to accurately and efficiently measure the dietary intake of Nigeria are lacking. We aimed to develop and assess the usability of a new online dietary assessment tool for Nigeria, myfood24 West Africa. Methods: We developed myfood24 West Africa database using data from existing food composition tables, back-of-pack labels of packaged foods and research articles. A 7-step approach was used: identified data sources, selected foods, processed/cleaned data, calculated nutrient content of recipes, created/allocated portion sizes, quality-checked database, and developed food accompaniments. To pilot myfood24 West Africa, we recruited 179 university staff living in Nigeria using a cross-sectional design; usability was assessed using a questionnaire that incorporated the System Usability Scale (SUS) and feedback session. Results: The database included 924 foods with up to 54 nutrients and 35 portion-size images allocated to foods. 60% of the data were sourced from the 2019 West Africa Food Composition Table, 17% from back-of-pack labels, 14% from the 2017 Nigeria Food Composition Table, 5% from generated recipes and 4% items from published literature. 30% (n=53) self-recorded their diet on their own and 1345 entries were made. The mean SUS score of 74 (95% CI: 68,79) indicated good usability. The feedback showed the tool was easy to use, educative, and included a variety of locally foods consumed. Conclusion: This new tool will enhance the dietary assessment of the Nigerian population. More work will cover more foods from other regions of Nigeria and West African countries.

Buildings are responsible for approximately 40% of global energy consumption, putting pressure on the construction industry to mitigate its environmental impact. Therefore, there is an urgent need for innovative solutions to reduce power consumption, particularly in lighting systems. The study’s primary objective was to investigate novel integrated lighting solutions that significantly reduce energy use and they explore their enhancement through Building Information Modeling (BIM) and the Internet of Things (IoT) to further improve energy efficiency and reduce the carbon footprint in buildings. Hence, this literature review aimed to examine energy-saving actions, retrofitting practices and interventions across a range of multi-use buildings worldwide over the past six years. The objective was to diagnose the goals being undertaken and ultimately validate new actions and contributions to minimise energy consumption. First, daylight harvesting and retrofitting solutions were examined in conjunction with the latest technologies, also referred to the external shadings. In consequence of this matter, comes the lack or unappropriated coordination, and so waste of energy, between daylight and electrical lighting. Secondly, how the integration of BIM facilitates the design process, providing a complete overview of all the variables of the building, thus improving indoor daylight performance and proper lighting with energy analysis. Lastly, the review addresses the role of IoT in providing real-time data from sensor networks, allowing for continuous monitoring of building conditions. This systematic literature review explores the integration of the fields to address the urgent need for innovative strategies and sustainability in the built environment. Furthermore, it thoroughly analyses the current state of the art, identifying best practices, emerging trends and concrete insight for architects, engineers, and researchers. The goal is to promote the widespread adoption of low-carbon systems and encourage collaboration among industry professionals and researchers to advance sustainable building design.

The multi-stage, multi-level assembly job shop scheduling problem (MsMlAJSP) is commonly encountered in the manufacturing of complex customized products. Ensuring production efficiency while effectively improving energy utilization is a key focus in the industry. For the energy-efficient MsMlAJSP (EEMsMlAJSP), an improved imperialist competitive algorithm based on Q-learning (IICA-QL) is proposed to minimize the maximum completion time and total energy consumption. In IICA-QL, a decoding strategy with energy-efficient triggers based on problem characteristics is designed to ensure solution quality while effectively enhancing search efficiency. Additionally, an assimilation operation with operator parameter self-adaptation based on Q-learning is devised to overcome the challenge of balancing exploration and exploitation with fixed parameters, thus the convergence and diversity of the algorithmic search is enhanced. Finally, the effectiveness of the energy-efficient strategy decoding trigger mechanism and the operator parameter self-adaptation operation based on Q-learning is demonstrated through experimental results, and the effectiveness of IICA-QL for solving EEMsMlAJSP is verified by comparing with other algorithms.

The volatility and uncertainty associated with the high proportion of wind and PV output in the new power system significantly impact power and energy balance, making it challenging to accurately assess the risks related to renewable energy abandonment and supply guarante. Therefore, a probabilistic power and energy balance risk analysis method based on distributed robust optimization is proposed. Firstly, the affine factor and the flexible ramp reserve capacity of thermal power are combined to establish a probabilistic index, which serves to characterize the risk associated with power and energy balance. Drawing upon the principles of conditional value at risk theory, the risk indexes of load shedding power and curtailment power under a certain confidence probability are proposed. Secondly, the probability distribution fuzzy sets of uncertain variables are constructed using the distributionally robust method to measure the Wasserstein distance between different probability distributions. Finally, aiming at minimizing the operation cost of thermal power, the risk cost of power abandonment and the risk cost of load shedding, a distributed robust optimal scheduling model based on flexible ramp reserve of thermal power is established.

Waste management is a critical issue globally, and Bangladesh is no exception, facing significant challenges due to rapid urbanization, population growth, and inadequate infrastructure. This article explores comprehensive waste management strategies, including waste segregation, recycling, composting, and waste-to-energy technologies, emphasizing their environmental and health benefits. It examines the past and present waste management conditions in Bangladesh, highlighting the progress made and the persistent challenges. The article also compares waste management practices in neighboring countries like India, Bhutan, Sri Lanka, and Nepal, offering insights into potential improvements for Bangladesh. Emphasizing the need for public awareness, community involvement, and modern infrastructure, it calls for collaborative efforts to achieve sustainable waste management and environmental preservation in Bangladesh. This article examines the critical issue of waste management, emphasizing its importance in mitigating environmental pollution, conserving resources, and protecting public health. It provides a detailed analysis of various waste management strategies, including waste segregation, recycling, composting, and waste-to-energy technologies, highlighting their benefits and implementation challenges. Focusing on Bangladesh, the article traces the evolution of the country's waste management system, from past inadequacies to recent improvements, while acknowledging persistent issues such as rapid urbanization and insufficient infrastructure. Comparisons with waste management practices in neighboring countries like India, Bhutan, Sri Lanka, and Nepal offer valuable insights and potential strategies for Bangladesh to adopt. The article underscores the necessity of public awareness, community involvement, and robust infrastructure to achieve effective waste management. It calls for a collaborative approach involving government, private sector, NGOs, and local communities to develop sustainable solutions. By investing in modern waste management technologies and fostering responsible consumption and disposal habits, Bangladesh can address its waste management challenges, ensuring environmental preservation, public health, and overall national well-being.

Accurate forecasting of available energy portion that corresponds to the reservoir inflow of the month(s) ahead provides important decision support for the hydropower plants in energy pro-duction planning for revenue maximization, as well as for the environmental impact prevention, and flood control at the upstream and downstream of a basin. Therefore, a reliable forecasting tool or model is deemed necessary and crucial. Considering the fluctuation and nonlinearity of data which significantly influence the forecasting results, this study develops an effective hybrid model by integrating Artificial Neural Network (ANN) and Particle Swarm Optimization (PSO) called “PSO-ANN” model based on the hydrological and meteorological data pre-processed by cross-correlation function (CCF), autocorrelation function (AFC), and normalization techniques for predicting the available energy portion corresponding to the reservoir inflow mentioned above for a case study hydropower plant in Laos namely, Theun-Hinboun hydropower plant (THHP). The model was evaluated by using correlation coefficient (r), relative error (RE), root mean square error (RMSE), and Taylor diagram plots in comparison with the popular single algorithm approaches such as ANN, and NARX models. Results demonstrated the superiority of the proposed PSO-ANN approach over the other two models.

Heat pumps are recognized as a key tool in the energy transition toward a carbon-neutral society, enabling the electrification of the heating sector at least for low- and medium-temperature heat demands. In recent years, natural refrigerants have been reconsidered due to their low environmental impact: among them, CO2 is a safe option without impact on the ozone layer and low global warming potential compared to synthetic fluids. However, as a consequence of its thermophysical properties, its thermodynamic cycle is transcritical and is particularly suitable for specific end-user temperature profiles. This paper analyzes in a systematic and thorough way the most significant modifications to the reference cycle that have been proposed in the literature to improve the performance, finding how the optimum configurations change with a change in the rated operating conditions (inlet temperature and temperature glide of the heat demand, and ambient temperature). Exergy analysis explains why there is an optimal gas cooler pressure and why its trend with the average temperature is split into two distinct regions, clearly recognizable in all cycle layouts. The maximum coefficient of performance (COP) of the reference cycle varies in the 1.52–3.74 range, with a second-law efficiency of 6.436.1, for an optimal gas cooler pressure of up to 15.45MPa, depending on ambient temperature and end-user temperature profile. The most effective modification is the cycle with ejector and internal heat exchanger, which raises the COP to 1.84–4.40 (second-law efficiency 8.745.56). The presented results provide an extensive guide to understanding the behavior of a transcritical CO2 cycle and predict its performance in heat pump applications.

Improving photobioreactor performance for microalgae cultivation has attracted many researchers over the past years. One of the primary challenges associated with existing photobioreactors is the light penetration. An effective photobioreactor design should maximize light penetration, ensuring uniform illumination throughout the reactor. This study aims to assess the impact of light intensity on microalgal growth from the perspective of energy efficiency and productivity in two photobioreactors. A novel cactus-like and a cylindrical photobioreactor were designed and fabricated using 3D printing technology. These two photobioreactors were used to cultivate two strains of microalgae. The novel photobioreactor achieved a maximum biomass productivity of 0.99 g/L/d and a maximum energy efficiency of 0.3139 g/d/kWh. The cylindrical photobioreactor reached a maximum biomass productivity of 0.74 g/L/d and 0.2199 g/d/kWh of energy efficiency. The increase in biomass productivity can be linked to enhancements in the photobioreactor's surface-to-volume ratio and better light utilization.

In this investigation, the impact of reducing agent concentration on the synthesis of zinc oxide nanoparticles was examined. During the synthesis, an assessment of ionic conductivity was carried out, revealing a significant increase in conductivity prior to the introduction of the reducing agent, followed by a sharp decrease upon its addition. Characterization of the ZnO NPs involved UV-visible spectroscopy, scanning electron microscopy, Fourier Infrared Spectroscopy, and X-Ray Diffraction analysis. The outcomes suggest that the characteristics of the ZnO NPs are influenced by the concentration of the reducing agent during the synthesis process. Notably, the ZnO NPs synthesized with a higher concentration of reducing agent exhibited a narrower optical band gap and increased surface energy. Furthermore, employing a concentration of 0.5 v/v resulted in the rapid production of nanoparticles with relatively uniform sizes. Conversely, concentrations below 0.5 v/v lead to slow formation, while concentrations exceeding 0.5 v/v yielded non-uniform nanoparticles.

This paper designed a new type of generator, transgenerator, that integrates the wind turbine and flywheel into one system, aiming to make the flywheel distributed energy storage (FDES) more modular and scalable than the conventional FDES. The transgenerator is a three-member dual-mechanical-port (DMP) machine with two rotating members (inner and outer rotors) and one stationary member (stator). The transgenerator-flywheel system is introduced with the system configuration, transgenerator overview, flywheel operation principle and power management strategies, and control system. Simulations are performed in MATLAB/ Simulink to verify the system viability, including control system verification and the flywheel storage performance evaluation. Results show that the inner and outer rotors can be controlled independently with accurate and fast control response, and the grid-side control works properly. The flywheel performs well with considerable charging power and storage capacity.

This qualitative research investigates the intricate relationship between market dynamics and supply chain sustainability in the renewable energy sector. Amidst the global energy transition, renewable energy has emerged as a crucial player in mitigating climate change and fostering sustainable development. However, ensuring the sustainability of renewable energy supply chains presents complex challenges shaped by various market forces. Through semi-structured interviews and thematic analysis, this study explores how policy frameworks, technological innovation, market competition, consumer preferences, and investor demands influence sustainability practices across the renewable energy supply chain. The findings highlight the critical role of supportive policy environments, technological advancements, and stakeholder collaboration in driving sustainability performance and mitigating risks within renewable energy supply chains. Furthermore, the study identifies challenges such as supply chain complexity, regulatory compliance, and stakeholder engagement, underscoring the need for collaborative efforts and multi-stakeholder partnerships. By addressing these challenges and leveraging opportunities, stakeholders can advance sustainability goals, mitigate climate change impacts, and foster a more resilient and equitable renewable energy sector. The research contributes to a deeper understanding of market dynamics and supply chain sustainability in the renewable energy sector, offering insights for policymakers, industry stakeholders, and sustainability practitioners to inform evidence-based decision-making and drive positive change.

The adoption of Industry 4.0 technology is essential for achieving energy efficiency, a critical aspect of Sustainable Development Goal (SDG) no. 12 aimed at addressing climate change. Understanding the impact of Sustainable Attitudes, Digital Trust, and Uncertainty Avoidance is crucial in the decision-making process regarding the implementation of Industry 4.0 technology. The slow adoption of Industry 4.0 technology is attributed to non-technological factors or people, while the need to achieve energy efficiency targets necessitates examining the influence of Sustainable Attitudes and Digital Trust as supporting variables, along with Uncertainty Avoidance, on technology adoption. The study employed a quantitative explanatory research approach to investigate the relationships and impacts of variables. It centered on employees of Schneider Electric Indonesia, a global Industry 4.0 technology provider, with a sample of 189 employees selected through random sampling, incorporating a 5% margin error from Slovin formula. The analysis involved the use of Structural Equation Modeling (SEM) with AMOS version 26. Industry 4.0 technology is essential for fostering innovation and business expansion, leading to a sustainable environment by offering principles, guidance, and energy-efficient technologies for companies. The involvement of Sustainable Attitude, moderated by Uncertainty Avoidance, is vital in reaching energy efficiency goals through Industry 4.0 implementation.

The energy transition is a challenge that affects all sectors, from transport to civil structures and industry. With reference to the industrial sector, the greatest need is the decarbonisation of industries energy-intensive, such as producers of iron and steel, aluminium, cement, petrochemicals, paper, etc. In particular, the steel industry is a hard to abate high-emissivity industry which due to chemical processes and high thermal demands (often above 500 °C) contributed to 7.4% of global CO₂ in the year 2021. This paper has explored the potential applications of hydrogen in the hard-to-abate sectors, highlighting its versatility and significance in decarbonization efforts. It provides an overview of hydrogen production methods, emphasizing the importance of sustainable and green hydrogen production. It reviews hydrogen production methods, storage, and potential in blended combustion. In the final part of the article, some considerations are introduced on the possible role of hydrogen in the steel sector (both as a supplementary fuel and as a reducing agent in innovative processes), showing how although there is potential for its inclusion as an element for the decarbonization, it is necessary to evaluate the energy balances of the various processes and the methods of hydrogen production very carefully, in order not to risk obtaining a marginal effect.

Sri Lanka's vulnerability to climate change-induced natural disasters, particularly floods, under-scores the urgent need for an integrated approach to disaster risk management (DRM) that ad-dresses the interconnected challenges within the water-food-land-energy nexus. The Deduru Oya basin, located in the north-western region, exemplifies this vulnerability, with its predominantly intermediate climatic zone susceptible to flooding. While the focus has traditionally been on flood risk reduction, it is imperative to recognize the broader implications of floods on water, food, land, and energy systems. This study aims to strengthen data acquisition and management efforts to better understand rainfall trends and their impact on the water-food-land-energy nexus in the Deduru Oya basin. By compiling 60 years of rainfall data and conducting time series analysis, we observed a decreasing trend in monthly rainfall, particularly during the South-West Monsoon, Second Inter Monsoon, and North-East Monsoon seasons. These findings have significant implica-tions for water availability, agricultural productivity, land use patterns, and energy generation in the basin. Moreover, the malfunction of stakeholders' responsibilities for local-level flood risk management exacerbates the challenges faced by communities living in flood-prone areas. By in-tegrating insights from this study into flood risk management strategies, stakeholders can develop holistic approaches that not only mitigate flood risk but also enhance resilience across the water-food-land-energy nexus. This interdisciplinary approach will inform policymakers, flood manag-ers, practitioners, and the community in formulating effective strategies to address the multifacet-ed challenges posed by floods in the Deduru Oya basin and beyond.

In the context of the minimally extended varying speed of light (meVSL) model, both the absolute magnitude and the luminosity distance of type Ia supernovae (SNe Ia) differ from those predicted by general relativity (GR). Utilizing the Pantheon+ data, we examine the plausibility of various dark energy models under meVSL. Both ωCDM and CPL parameterization dark energy (DE) models exhibit indications of cosmic variations in the speed of light at the 1-σ level. For Ωm0=0.30,0.31, and 0.32 with (ω0,ωa)=(−1,0), the 1-σ range of c˜˙0/c˜0(10−13yr−1) is (-8.76 , -0.89), (-11.8 , 3.93), and (-14.8 , -6.98), respectively. Meanwhile, the 1-σ range of c˜˙0/c˜0(10−12yr−1) for CPL dark energy models with −1.05≤ω0≤−0.95 and 0.28≤Ωm0≤0.32, is (-6.31 , -2.98). The value of c˜ at z=3 can exceed that of the present by 0.2∼3 % for ωCDM models and 5∼13 % for CPL models. Additionally, for viable models except for the CPL model with Ωm0=0.28, we find −25.6≤G˜˙0/G˜0(10−12yr−1)≤−0.36. For this particular model, we obtain an increasing rate of the gravitational constant within the range 1.65≤G˜˙0/G˜0(10−12yr−1)≤3.79.

We will demonstrate that the photon energy density parameter Ωγ of the universe can be derived exactly in Rh = ct cosmology. We find that it must be Ωγ = 1/5760π ≈ 5.52621330180192× 10^(−5). This indicates that there is no uncertainty in the radiation density within at least somesub-classes of Rh = ct cosmology.

First, a recently developed eigenfunction expansion technique, based in part on separation of the thickness-variable and partly utilizing a modified Frobenius type series expansion technique in conjunction with the Eshelby-Stroh formalism, is employed to derive three-dimensional singular stress fields in the vicinity of the front of an interfacial crack weakening an infinite bicrystalline superlattice plate, made of orthorhombic (cubic, hexagonal and tetragonal serving as special cases) phases, of finite thickness and subjected to the far-field extension/bending, in-plane shear/twisting and anti-plane shear loadings, distributed through the thickness. Crack-face boundary and interface contact conditions as well as those that are prescribed on the top and bottom surfaces of the bicrystalline superlattice plate are exactly satisfied. It also extends a recently developed concept of lattice crack deflection (LCD) barrier to a superlattice, christened superlattice crack deflection (SCD) energy barrier for studying interfacial crack path instability, which can explain crack deflection from a difficult interface to an easier neighboring cleavage system. Additionally, the relationships of the nature (easy/easy, easy/difficult or difficult/difficult) interfacial cleavage systems based on the present solutions with the structural chemistry aspects of the component phases (such as orthorhombic, tetragonal, hexagonal as well as FCC (face centered cubic) transition metals and perovskites) of the superlattice are also investigated. Finally, results pertaining to the through-thickness variations of mode I/II/III stress intensity factors and energy release rates for symmetric hyperbolic sine distributed load and their skew-symmetric counterparts that also satisfy the boundary conditions on the top and bottom surfaces of the bicrystalline superlattice plate under investigation, also form an important part of the present investigation.

Live video streaming has become one of the main multimedia trends in networks in recent years. Providing Quality of Service (QoS) during live transmissions becomes a challenge due to the stringent requirements for low latency and minimal interruptions. This scenario has led to a high dependence on cloud services, implying a widespread usage of Internet connections, which constrains contexts where an Internet connection is not available. Thus, alternatives such as Mobile Ad Hoc Networks (MANETs) emerge as potential communication techniques. These networks operate autonomously with mobile devices serving as nodes, without the need for coordinating centralized components. However, these characteristics lead to challenges to live-video streaming, such as dynamic node topologies or periods of disconnection. Considering these constraints, this paper investigates the application of Artificial Intelligence (AI)-based classification techniques to provide adaptive streaming in MANETs. For this, a software-driven architecture is proposed to route stream in offline MANETs, predicting the stability of individual links and compressing video frames accordingly. The proposal has been implemented and assessed in a laboratory context, analyzing the model performance and QoS metrics. As a result, the model is implemented in a decision forest algorithm, which provides 95.9% of accuracy. Also, obtained latency values become assumable for video streaming, manifesting a reliable response for routing and node movements.

The new energy structure needs to balance energy security and dual carbon goals, which has brought major challenges to coal-fired power plants, the pollution reduction and carbon emissions reduction of coal-fired power plants will be a key task in the future. This article proposes an optimization operation of electrostatic precipitators(ESP), based on the working mechanism and historical data of ESP, voltage-current characteristic model and outlet dust concentration prediction model are constructed by deep learning algorithm, Particle Swarm Optimization(PSO) is used to achieve the optimal energy consumption while ensuring stable outlet dust concentration. By training with historical data collected on site, accurate prediction of secondary current and outlet dust concentration of ESP has been achieved, the Mean Absolute Percentage Error(MAPE) of secondary current is less than 1.5%, and the MAPE of outlet dust concentration of ESP on the test set is less than 5.2%. Finally, the optimization experiment is carried out in a 330MW coal-fired power plants, the results showed that the fluctuation of the outlet dust concentration is more stable, and the energy saving is about 43% after optimization, according to the annual operation of 300 days, the annual average carbon reduction is approximately 2621.34 tons. This method is effective and can be applied widely.

The study of angular correlations of heavy-flavor particles in hadronic collisions can provide crucial insight into the heavy-quark production, showering and hadronization processes. The comparison with model predictions allows us to discriminate among different approaches for heavy-quark production and hadronization, as well as different treatments of the underlying event employed by the models to reproduce correlation observables. In ultra-relativistic heavy-ion collisions, where a deconfined state of matter, the quark-gluon plasma (QGP), is created, heavy-flavor correlations can shed light on the modification of the heavy-quark fragmentation due to interaction of charm and beauty quarks with the QGP constituents, as well as characterize their energy loss processes while traversing the medium. Insight into possible emergence of collective-like mechanisms in smaller systems, resembling those observed in heavy-ion collisions, can also be obtained by performing correlation studies in high-multiplicity proton-proton and proton-nucleus collisions. In this review, the most recent and relevant measurements of heavy-flavor correlations performed in all collision systems at the LHC and RHIC will be presented, and the new understandings that they provide will be discussed.

Steel damper columns (SDCs) are energy-dissipating members that are suitable for reinforced concrete (RC) buildings and are often used for multistory housing. The evaluation of the peak deformation and hysteretic dissipated energy of such building structures is essential for the rational seismic design of RC buildings with SDCs. In a previous study, the authors proposed an energy-based prediction procedure for the peak and cumulative response of an RC frame building with SDCs. In this procedure, the accuracy of the equivalent velocity of the maximum momentary input energy (V_ΔE1^*)–peak equivalent displacement (D₁^*_max) relationship is essential for high quality predictions. In this article, the V_ΔE1^*–D₁^*_max relationships of RC moment-resisting frames with and without SDCs are invested using a critical pseudo-double impulse (PDI) analysis based on a study by Takewaki and coauthors. The results show that the V_ΔE1^*–D₁^*_max relationship obtained from the critical PDI analysis agrees well with that calculated from the equations proposed in the previous study.

Swarf of aluminum alloy with high corrosion resistance and ductility was successfully converted into fine hydroreactive powders via its ball milling with silver powder and either lithium chloride or gallium. The later substances significantly intensified particle size reduction, while silver formed ‘cathodic’ sites (Ag, Ag2Al) promoting Al corrosion in aqueous saline solutions with hydrogen generation. The diffraction patterns, microphotographs, and elemental analysis results demonstrated partial aluminum oxidation in the samples and their contamination with tungsten carbide from milling balls. Those effects were responsible for obtaining hydrogen yields lower than expected. For AlCl3 solution at 60 °C, Al–LiCl–Ag, Al–LiCl, Al–Ga–Ag, and Al–Ga composites delivered (84.6±0.2), (86.8±1.4), (80.2±0.5), and (76.7±0.7)% of the expected hydrogen respectively. Modification with Ag promoted Al oxidation thus providing higher hydrogen evolution rates. The samples with Ag were tested in CaCl2 solution as well, for which the reaction proceeded much slower. At a higher temperature (80 °C) after 3 h of experiment, the hydrogen yields for Al–LiCl–Ag and Al–Ga–Ag powders were (46.7±2.1) and (31.8±1.9)%. The tested Ag-modified composite powders were considered promising for hydrogen generation and had a potential for further improvement to provide higher performance.

The increased focus on sustainability in response to climate changes has given rise to many new initiatives to meet the rise in building load demand. The concept of distributed energy resources (DER) and optimal control of supply to meet power demands in buildings have resulted in growing interest to adopt microgrids for a precinct or a university campus. In this paper, a model for an actual physical microgrid has been constructed in OPAL-RT for real-time simulation studies. The load demands for SIT@NYP campus and its weather data are collected to serve as input to run on the digital twin model of DERs of the microgrid. The dynamic response of the microgrid model in response to fluctuations in power generation due to intermittent solar PV generation and load demands are examined via real-time simulation studies and compared with the response of the physical assets. It is observed that the simulation results match closely to the performance of the actual physical asset. As such, the developed microgrid model offers plug-and-play capability which will allow power providers to better plan for on-site deployment of renewable energy sources and energy storage to match the expected building energy demand.

We discuss the neutron skins of 48Ca and 208Pb. We review and critically examine modern predictions and empirical constraints, with special attention to the dierent interpretations of the ndings from the PREX-II experiment and the recently reported value of the neutron skin in 48Ca extracted from the CREX experiment. We argue that, in the spirit of the ab initio philosophy, the path to understanding the behavior of dense neutron-rich matter must not circumvent fundamental nuclear forces. Based only on that argument, a thick neutron skin in 208Pb is highly unlikely.

This comprehensive review explores the principles, applications, and future directions of human-powered energy generation technologies. It begins by providing a detailed examination of viable human energy sources, elucidating the physical principles behind various energy harvesting devices. The review then compiles and assesses existing products in the field of human power generation, while also outlining the opportunities and challenges it presents. Finally, an innovative concept of an eco-village system is introduced to demonstrate a future potential application scenario for human-generated electricity. It outlines two developmental stages for this system and underscores its significance in the construction of the harmonious and sustainable communities. This forward-thinking approach could pave the way for broader discussions on sustainable living and eco-friendly energy generation in a world increasingly focused on environmental concerns and social stability.

High Vacuum Flat Plate Collectors (HVFPCs) are the only type of Flat Plate Thermal Collectors capable of producing thermal energy for middle-temperature applications (until 180 °C). As the trend of research plans to develop new Selective Solar Absorbers to extend the range of HVFPC application until 250 °C, it is necessary to correctly evaluate the collector efficiency up to such temperature to predict the energy production accurately. We propose an efficiency model for these collectors based on the selective absorber optical properties. The proposed efficiency model explicitly includes the radiative heat exchange with the ambient, which is the main source of thermal losses for evacuated collectors at high temperatures. It also decouples the radiative losses that depend on the optical properties of the absorber adopted from the other thermal losses due to HVFPC architecture. The model has been validated by applying it to MT-Power HVFPC manufactured by TVP-Solar, and it has been used to predict the efficiency and energy production of HVFPC equipped with new, optimized selective solar absorbers developed in recent years.

The Supersymmetry Genetic code (SSyGC) table is based on five physicochemical symmetries: 1) double mirror symmetry on the principle of the horizontal and vertical mirror symmetry axis between all bases (purines [A, G) and pyrimidines (U, C)], and 2) of bases in form of codons 3) direct – complement like codon/anticodon symmetry in the sixteen alternating boxes of the genetic code columns, 4) A+T rich and C+G rich alternate codons in the same row between both columns of the genetic code, 5) the same position between divided and undivided codon boxes in relation to horizontal mirror symmetry axes. The SSyGC table has a unique physicochemical purine – pyrimidine symmetry net which is as the core symmetry common for all, more than thirty different nuclear and mitochondrial genetic codes. This net is present in the SSyGC table of all RNA and DNA living species. None of these symmetries is present in the Standard Genetic Code (SGC) table which is constructed on the alphabetic horizontal and vertical U-C-A-G order of bases. Here we show that the free energy value of each codon incorporated as fundamentally mapping the “energy code” in the SSyGC table is compatible with mirror symmetry. On the other hand, in the SGC table the same free energy values of codons are dispersed and a mirror symmetry between them is not recognizable. At the same time the mirror symmetry of the SSyGC table and the DNA quadruplets together with our classification of codons/trinucleotides are perfectly imbedded in the mirror symmetry energy mapping of codons/trinucleotides and point out in favor of maintaining the integrity of the genetic code and DNA genome. We also argue that physicochemical symmetries of the SSyGC table in the manner of the purine – pyrimidine symmetry net, the quadruplet symmetry of DNA molecule and the free energy of codons have remined unchanged during all of evolution. The unchangeable and universal symmetry properties of the genetic code, DNA molecule and energy code are decreasing disorder between codons/trinucleotides and shed a new light on evolution. Diversity in all living species on Earth is broad, but the symmetries of the Supersymmetry Genetic Code as the code of life and the DNA quadruplets related to the” energy code” are unique, unchangeable and have the power of natural laws.

Despite great interest in how dynamic fluctuations in psychological states such as mood, social safety, energy, present-focused attention, and burnout impact stress, well-being, and health, most studies examining these constructs use retrospective assessments. Here, we discuss how ecological momentary assessments (EMAs) address methodological issues associated with retrospective reports, able to reveal dynamic associations between psychological states at small timescales that are often missed in stress and health research. In addition to helping researchers characterize daily and within-day fluctuations and temporal dynamics between different health-relevant processes, EMAs can elucidate mechanisms through which interventions reduce stress and enhance well-being. EMAs can also be used to identify changes that precede critical health events, which can in turn be used to inform the delivery of ecological momentary interventions (EMIs of just-in-time interventions) that prevent such events from occurring. To enable this work, this narrative review provides examples of scales and single-item questions used in EMA studies, makes concrete recommendations for researchers seeking to employ EMAs in their research, and discusses limitations of EMA methods. In doing so, we aim to encourage the use of these methods in research given that, when used carefully, EMA methods are well-poised to greatly advance our understanding of how intrapersonal dynamics affect stress levels, well-being, and human health.

Buildings can play an important role in reducing GHG emissions through increased energy efficiency. The European Commission issued a proposal in 2021 suggesting that all new buildings should be “zero-emission Buildings” (ZEB), aiming at a zero GHG emission building stock by 2050.The extent to which ZEB can contribute to reduced GHG emissions, however, varies between countries, due to different energy systems. It is also important to consider other environmental effects to avoid that climate benefits come with unintended consequences.Here, we explore the life-cycle environmental performance for a ZEB in a case where electricity and heating is largely fossil-free. The assessment concentrates on i) environmental impact of the use stage in relation to the product stage, ii) the interrelation between different energy sources, with attention on household electricity, and iii) the performance for more impact categories than primary energy use and climate change. While our results generally support the use of ZEBs from an environmental perspective, they also show that the climate benefit in this setting is marginal. However, given that energy systems are connected and energy savings in one place can reduce the demand for fossil energy elsewhere, the climate benefit of ZEBs is likely underestimated. Besides methdological implications for future studies, this indicates that current EU policy is promising, as incentives for implementation of ZEBs is unaffected by domestic effects.

Running is a basic form of human locomotion and one of the most popular sports worldwide. While the leg biomechanics of running have been studied extensively, few studies have focused on the upper-body movement. However, an effective arm swing and longitudinal rotation of the shoulders play an important role in running efficiency as they must compensate for the longitudinal torques generated by the legs. The aim of this study is to assess the upper-body rotation using wearable inertial sensors and to elucidate its relation to energy expenditure. Eighty-six junior elite middle and long-distance runners (37 female, 49 male) performed an incremental treadmill test with sensors attached on both shoulders, tibiae and the sacrum. Mean and total horizontal shoulder and pelvis rotation per stride were derived while energy costs were determined using respiratory gas analysis and blood sampling. Results show that shoulder and pelvis rotation increase with running speed. While shoulder rotation is more pronounced in female than in male runners, there is no sex difference for pelvis rotation. Energy cost of running and upper trunk rotation prove to be slightly negatively correlated. In conclusion, upper body rotation appears to be an individual characteristic influenced by a sex-specific body mass distribution.

Agriculture uses a lot of fuel, fertilizers, pesticides and other substances, while emitting large amounts of GHGs. It is important to optimize these inputs and outputs. One such way is increas-ing crop biodiversity. For this reason, single crops and mixtures of maize, hemp and faba bean as binary and ternary crops were investigated at the Experimental Station of Vytautas Magnus Uni-versity, Lithuania. Results showed that consumption of diesel fuel was by the 31-46% higher than in single and 22-35% higher than in binary cultivations was found in a ternary crop. This influenced on the highest energy input or near twice higher than in maize and hemp single crops and maize+hemp binary crop, but similar with binary crops with faba bean. Despite this, the productivity of the trinary crop and, at the same time, the energy output were 2-5 times higher than in other treat-ments. This compensated for higher energy inputs and the energy efficiency ratio. In ternary crop, energy productivity was from 1.1 to 2.8 times higher and net energy was by 1.9-5.3 times higher than in other tested cultivations. The highest total GHG emissions were obtained in binary maize+hemp and maize+faba bean cultivations (1729.84 and 2067.33 CO2eq ha-1). Ternary cultiva-tion with the highest energy inputs initiated average GHG emission - 1541.90 kg ha-1 CO2eq. For higher efficiency, ternary crop could be sown and harvested in one machine pass. Faba beans should be included in the ter-nary crops, as their biomass takes a significant part of the total biomass produced. We recommend to review the inter-cropped faba bean seeding rates as faba bean seeds have a high energy input equivalent.

Modeling and assessing the sustainability of machining systems has been considered to be a crucial approach to improving the environmental performance of the machining processes. As the most common machining system, the computer numerical control (CNC) milling system is a typical man-machine cooperative system where the activities of the machine tool and operator generate material and energy consumption. However, the energy consumption of the operator in the CNC milling system has often been ignored in most existing research. Therefore, existing methods fail to provide a comprehensive understanding of the sustainability of the CNC milling system. To fill this gap, an exergy loss assessment method is proposed to investigate the sustainability of the CNC milling system, where the energy consumption of the operator, the energy consumption of the machine tool, and material consumption are taken into consideration. The key performance indexes of the energy consumption of the operator, the energy consumption of the machine tool, the exergy loss, and the specific exergy loss (SEL) are analyzed and modeled. To demonstrate the feasibility of the proposed method, a case study was carried out on a three-axis machining center (XH714D), in which SEL was found to be 88.04J/mm3. The proposed method is effective to assess the sustainability of the CNC milling system, and the established exergy loss models build a good basis for exergy efficiency optimization.

The refractive index of solids guages their transparency to incident light, while the energy gap determines the threshold for light absorption. This paper provides a mathematical formulation for the relationship between refractive index and energy gap. It is also established that this formulation aided in the unification of the Moss, Ravindra, and Herve-Vandamme relationships.

Intraband energy transitions of an electron in GaAs/AlGaAs hexagonal quantum well wires in the presence of external electric and magnetic fields are presented. We consider the effects of the revolve of the quantum well wires via a geometric factor that converts the quantum wires straight and symmetric with respect to the z−axis, into a curved wires that no longer has this symmetry. In addition, the influence of having a shallow donor impurity on (off) is calculated. The shape of this quantum string corresponds to the core/shell structure. The energy levels and wave functions of the electron in the heterostructure with a finite potential between the shells are calculated using the effective mass approximation and the finite element method. The calculations of the optical properties are obtained from the compact density matrix and an iterative method. The direction of the applied external fields is parallel (anti-parallel) to the z−direction. The results reveal a significant dependence of the physical properties calculated with the deformation parameter, the dimensions of the quantum well wires and the presence or not of the impurity. The electronic transitions are in a range between 4.90 meV to 41.50 meV under the effect of the electric field, this corresponds to a range of frequencies of optical responses between 1.20 to 10 THz, that is, the mid-infrared. For the magnetic field the range is between 1.24 meV to 14 meV, that is, in frequencies from 0.36 to 3.38 THz, that is, in the far-infrared.

This comprehensive critical review shows how green buildings and energy optimization solutions improve indoor air quality as well as environmental quality (IEQ) and human health. Electricity-efficient green buildings create a better indoor atmosphere and save electricity. Green buildings improve occupant well-being through IAQ, thermal comfort, acoustics, and lighting. Renewable energy, green construction materials, and intelligent technologies increase sustainability and reduce environmental impact. Environmental hazards, architectural design, and societal variables can improve indoor air quality and subsequently reduce health risks linked with poor air quality. The evaluation highlights the pros and cons of low-cost IAQ sensors and equipment. These devices provide valuable insights, but calibration and validation using reference equipment are necessary to ensure accuracy and reliability. Architects, engineers, environmentalists, and policymakers are essential in creating green buildings with high IEQ. Prioritizing occupant comfort, health, and productivity ensures a sustainable and healthy future for future generations. However, continual monitoring and research are needed to improve green building practices and overcome construction problems. Intelligent models for continual on-field calibration of low-cost sensors may improve performance. Green buildings benefit occupants and the environment by optimizing energy use and using IAQ monitoring technologies.

In the context of "dual carbon", with the continuous deepening of the power system reform, the application of high proportion renewable energy is becoming increasingly widespread. All sectors of society have put forward higher requirements for electricity sales packages, which can guide the behavior of power users, promote energy conservation and emission reduction, and finally promote low-carbon operation of the power market economy.Therefore, the requirements of power users and power selling companies for the power selling package are increasing, which puts forward higher requirements to the power selling package recommended by the power selling company . However, the existing recommendation methods are unable to make appropriate recommendations for the users with lack of preference information. Therefore, this paper proposes a two-sided matching decision-making method of electricity sales package based on disappointment theory. First of all, according to the incomplete fuzzy preference relationship provided by the power user and the electricity sales package, the respective priority weight vector is obtained, and then the subjective satisfaction matrix of the power user and the electricity sales package to each other is obtained; Next, the adjusted satisfaction matrix is calculated by adding the influence of the theory of joy and disappointment; Then, based on the adjusted satisfaction matrix, an optimization model aiming at maximizing the total satisfaction of power users and electricity sales packages is established, and the optimal stable matching model of power users and electricity sales packages is obtained; Finally, taking an industrial park in Zhejiang Province as an example, by using the bilateral matching method proposed in this article, the optimal matching schemes for 5 power users and 6 electricity sales packages are obtained, which shows the effectiveness and rationality of the two-sided matching decision-making method of electricity sales package based on the disappointment theory proposed in this paper.

Ni-Al alloys have good corrosion-resistant properties making them preferable as a material of choice compared to ordinary metals. A good understanding of the phase diagram and thermodynamic properties of the Ni-Al alloy binary system is essential in determining relevant industrial applications of the system. The Ni-Al phase diagram is being reassessed since those found in the literatures are based on very old experimental studies. The phase diagram and thermodynamic properties of the Ni-Al alloy is determined using the Thermo-Calc 2022b software over a temperature range of 200 K to 2000 K and 1 atm of pressure. A total of nineteen fields (including elemental Al and Ni) comprising of five single solid phases, one liquid phase, and twelve double regions was obtained from the equilibrium calculation. The thermodynamic calculation has six invariant reactions comprising of two eutectic reactions (914.83 ± 0.025 K and 1641.80 ± 0.025 K), three peritectic reactions (1123.55 ± 0.025 K, 1400.72 ± 0.025 K and 1642.65 ± 0.025 K), and one peritectoid reaction (913.96 ± 0.025 K). The solubility of Al in Ni is also determined. The Thermo-Calc temperature – composition of the Ni-Al alloy is compared with the existing experimental studies to identify the physical properties of the different thermodynamic properties of the Ni-Al alloy binary system.

Deep brain stimulation (DBS) is an effective and safe medical treatment that improves the lives of patients with a wide range of neurological and psychiatric diseases, and has been consolidated as a first-line tool in the last two decades. Closed loop deep brain stimulation (CLDBS) pushes this tool further by automatically adjusting the stimulation parameters to the brain response in real-time. This paper presents a CLDBS with 2 stimulation channels and 2 acquisition channels. Each channel has a low-noise amplifier (LNA) buffer in differential configuration to eliminate the DC signal component of the input. Energy management is efficiently done by the control and communication unit. The battery supports almost 9 hours with both the acquisition and stimulation circuits active. If only the stimulation circuit is used as an Open Loop DBS (OLDBS), the battery can hold sufficient voltage for 24 hours of operation. The whole system is low-cost and portable and therefore it could be used as a wearable.

The response of structures under pulse-like ground motions is characterized by the large amount of energy input in a few cycles. Consequently, structures with insufficient strength may suffer severe damage owing to excessive deformation. In a previous paper, the energy-based prediction procedure for the peak and cumulative response of a reinforced concrete (RC) frame building with steel damper columns was proposed (Fujii and Shioda, 2023). Although this procedure was verified by comparison to the nonlinear time-history analysis (NTHA) results, the performance of the proposed procedure with pulse-like ground motion records has not been verified yet. In this study, the accuracy of the energy-based prediction procedure for an RC frame building with steel damper columns was investigated by considering pulse-like ground motions. The numerical analysis results reveal that the accuracy of the predicted peak response is satisfactory, which agrees with the results of the author’s previous study. However, the accuracy of the predicted total input energy to the building model depends on the ratio of the pulse period of the ground motion to the effective fundamental period of the building model. The reasons for this underestimation of the total input energy are discussed in this paper.

Many techniques have been and are being made to find alternatives to water-saving practices. Among them, Partial root drying (PRD), one of the effective approaches, plays a major role in reducing the harmful effects of water deficit stress. An experiment was carried out using irrigation strategies [I1 (100% full irrigation “FI”), I2 (75%FI), I3 (50%FI), and I4 (PRD (50%FI)] and soil organic mulch [L0 (Zero layer organic soil mulch” control”), L1 (Single layer organic soil mulch), L2 (Two layers of organic soil mulch), and L3 (Three layers of organic soil mulch)] to inspect the impact of those treatments for increasing yield, water productivity and saving energy under arid region conditions. To meet the study's objective, two field experiments were carried out at a private farm. Our results demonstrated a general decrease in water stress and salt accumulation inside root-zone area with PRD with L3. The PRD strategy increased fruit yields by 3.7 and 7.3% and water productivity by 51.9 and 53.1% compared with I1 during 2020/2021 and 2021/2022, respectively, while reducing the applied irrigation water by 50 %. The PRD strategy showed superior results in increasing mango yield and water productivity. In general, PRD can be used as good technique to save water and energy up to 50% and enhance productivity along with using organic mulching, ultimately improving mango yield under arid climatic regions. It may prove a good adaptation strategy for current and future water shortage scenarios of climate change.

Deep learning has been applied in many areas that have had a significant impact on applications that improves real-life challenges. The success of deep learning in a wide range of areas is due in part to the use of activation functions, which are particularly effective at solving non-linear problems. Activation functions are a key focus for researchers in artificial intelligence who aim to improve the performance of neural networks. This article provides a comprehensive explanation and comparison of different activation functions, with a focus on the arc tangent and its variations specifically. The paper presents experimental results that show that variations of the arc tangent using irrational numbers such as pi, the golden ratio, and Euler’s number, as well as a self-arctan function, produce promising results. Since we experimented with promising activation functions on two different problems, and datasets, we reached a result that different irrationals work well for different problems. In other words, arctan ϕ gives the best results mostly for multiclass classification and arctan e gives the best results for time series prediction problems. The paper focuses on a multiclass classification problem applied to the Reuters Newswire dataset and a time-series prediction problem on Türkiye energy trade value to show the impacts of activation functions.

Integrating numerous renewable resources has been extensively researched and studied to create a dependable energy system. This study investigated the best techno-economical hybrid energy system configuration while using hydrogen energy to keep the system's energy balanced. Additionally, this study aims to determine the best hybrid system configuration for the location under investigation. A novel technique of DBM (Deterministic Balanced Method) was introduced to determine the total annual energy output for the project's lifetime. This approach is used to contrast the outcomes of other HOMER software tools. Then, using HOMER, it is possible to confirm the sizing optimization results for the suggested method by comparing the power ratings and yearly energy output. A detailed comparison between our proposed method and HOMER Pro has been conducted for validation and verification. Our method has been rigorously tested in various hybrid off-grid energy systems, ensuring its applicability and reliability across different scenarios and configurations. The results of our study indicate a high degree of similarity between the proposed approach and HOMER pro for computing annual energy power for the studied energy systems. Specifically, our analysis revealed that the difference between the approaches was within a range of 5%, indicating a high level of consistency and reliability in our method. These findings suggest that our approach can be confidently applied to determine the appropriate size of hybrid energy systems accurately. Overall, our study provides valuable insights into the development of effective sizing methodologies for hybrid energy systems. After considering the amount of solar radiation and wind speed gathered by global weather data platforms like NASA and METEONORM, this paper has also included a real case study of the Cairo International Airport's hybrid renewable energy production systems. To guarantee the viability of this study, the system design was founded on an actual load that was researched and simulated. A cluster of distributed networks was finally proposed to use the excess energy and enable energy conversion processes to be used in industry and transportation applications.

Nuclear technologies have the potential to play a major role in the transition to a global net-zero society. Their primary advantage is the capability to deliver controllable 24/7 energy on demand. However, as a prerequisite for successful worldwide application, significant innovation will be required to create the nuclear systems of the 21st century, the need of the hour. The pros and cons of nuclear are discussed and analysed at different levels – the societal and public recognition as well as the scientific/engineering and economic level – to assure a demand driven development. Based on the analysis of the different challenges a vision for the nuclear system of the 21st century is synthesised consisting of three pillars – unlimited nuclear energy, zero waste nuclear, and accident free nuclear. These three combined visions are then transformed into dedicated and verifiable missions which are discussed in detail regarding challenges and opportunities. In the following a stepwise approach for the development of such a highly innovative nuclear system is described. Essential steps to assure active risk reduction and the delivery of quick progress are derived as answer to the critique on the currently observed extensive construction time and cost overruns on new nuclear plants. The 4-step process consisting of basic studies, experimental zero power reactor, small scale demonstrator, and industrial demonstrator is described. The 4 steps including sub-steps deliver the pathway to a successful implementation of such a ground breaking new nuclear system. The potential sub-steps are discussed with the view not only onto the scientific development challenges, but also as an approach to reduce the regulatory challenges of a novel nuclear technology.

Laser Powder Directed Energy Deposition (LP-DED) is an Additive Manufacturing process in which a laser beam is used to generate a melt pool onto a substrate. The additional material, in form of powder material, is fed into the generated melt pool and a raised track is obtained. The LP-DED process is very powerful for different applications such as the repair operations and the production of functionally graded material, however the application is still limited and one of the main reasons is related to the lack of knowledge in the physics of the process mechanisms. The process is influenced by a huge number of parameters and three main mechanisms can be identi-fied. These mechanisms are the powder flow, the generation of the molten pool and the solidifica-tion process and for each of these mechanisms the process parameters have a different relevance. In this paper, a review of the main mechanisms and the relationship between the process parame-ters and the outcome of each step of the process is presented.

Student attendance serves many other important purposes aside from monitoring. In certain universities, the attendance of students in a course is also used as one of the requirements for students to be allowed to sit for the final examination. Traditionally, among most Malaysian Institutions of Higher Learning (IHL), attendance recording is usually done using pen and paper, or uses simple web-based system that is time consuming and difficult for faculty periodic monitoring. To address the identified drawbacks, this research aims to develop a Smart Attendance for Faculty Monitoring System using the Bluetooth Low Energy (BLE) technology to assist faculty in recording, managing and monitoring students’ attendance and class schedules effectively. The system is developed for Android-based devices using an agile methodology consists of iteration and incremental approaches. Thus, to evaluate the effectiveness of the system, a survey was conducted on 140 respondents involving lecturers and students of Kolej Universiti Poly-Tech MARA (KUPTM). Respondents were selected using purposive sampling. The descriptive analysis showed that 87.9% of the respondents strongly agreed that the system is effective in assisting lecturers to record attendance, manage class schedules and student attendance as well as to assist faculty in monitoring students’ absenteeism.

Renewable active sludge is a smart material for wastewater treatment and the protection of surface water bodies. The generated pellets (dried and pelletised dehydrated anaerobically stabilised excess sludge) are produced in a quantity of 31.4 g ± 5.6 g dry matter (DM) per one Population equivalent (PE) calculated to COD (PE_COD) in one day. As pellets are combustible material, their energy utilisation must reach sustainable development goals (SDGs) - a bridge must be created between »treated sewage sludge as the tool to remove pollutants and nutrients from wastewater« and »preparation of the valuable material as a solid recovered fuel (SRF) that meets customer-specific requirements«. Technical Report CEN/TR 15508 and Technical Standard EN ISO 21640 set up methods for specifying and classifying pellets as an SRF. In the last eleven years (2010 – 2021), pellets' net calorific value (NCV) is 13.0 ± 0.7 MJ kg^-1 as received (ar). In 2021, the 80^th percentile of the Hg/NCV ratio was 0.079 mg Hg MJ^-1. In 2010 – 2021, the annual amount of Hg transferred to stakeholders reduced by 64.3 % m/m - from 10.1 kg to 3.67 kg. The halogen contents of the pellets do not threaten corrosion to the incineration facility. Stable pellets' energy potential and perspective ash composition for critical raw materials recovery qualify pellets as a specific waste stream and a renewable material for SRF production.

Environment approachable products such as fuels and lubricants are among the best choices in several countries that contain renewable products as alternatives. To protect human life, alternative methods of saving the environment and production balance is needed to reduce the effects of the crisis and the contamination of the Environment. This research concentrated on the Manufacturing and testing of bio- grease from sugar cane filter mud vegetable oil as a lubricant for friction reduction and determining the properties of both bio grease and Mineral oil grease with environmental problems. SC filter mud oil as an alternative use for bio-grease preparation in addition to mineral oil grease. The Testing was accepted to determine the quality of the eco-friendly grease produced. For the preparation of this bio- grease, the SC Filter cake sample is taken from different sugar factory which found in Ethiopia. The sample has a moisture content of 78%. Using this sample first oil is extracted by Soxhlet apparatus, n-hexane solvent and temperature for extraction from 42 -68℃. The maximum temperature and time for extraction of oil were 68 and 7hrs respectively. The extracted oil's physical properties include color, acid value, specific graphite, saponification value, iodine value, density, and viscosity. Finally, the friction behavior in function of time for both grease at identical load, the friction coefficient vs time for SC filter Cake Grease_ Na_ MoS2 and industrial mineral one (I_ Greasily _ MoS2), grease was determined.

Solar powering the increasing fleet of electrical vehicles (EV) demands more surface area than may be available for photovoltaic (PV) powered buildings. Parking lot solar canopies can provide the needed area to charge EVs, but are substantially costlier than roof- or ground-mounted PV systems. To provide a lower-cost PV parking lot canopy to supply EV charging beneath them, this study provides a full mechanical and economic analysis on three novel PV canopy systems: (1) exclusively wood, single parking spot spanning system, (2) wood and aluminum double parking spot spanning system, and (3) wood and aluminum cantilevered system for curbside parking. All systems can be scalable to any amount of EV parking spots. The complete designs and bill of materials (BOM) of the canopies are provided along with basic instructions and are released with an open source license that will enable anyone to fabricate them. The results found single-span systems have cost savings of 82%-85%, double-span systems save 43%-50%, and cantilevered systems save 31%-40%. In the first operation year, the PV canopies can provide 157% of energy needed to charge the least efficient EV currently on the market if it is driven the average driving distance in London ON, Canada.

This work deals with the performance evaluation of novel flat photovoltaic-thermal (PV-T) modules under vacuum. Through a 1D (dimensional) steady-state-energy-balance numerical model developed in MATLAB, two different layouts are studied: the first consisting of a photovoltaic (PV) cell installed just below the glass encapsulating the flat panel, and the second where the PV cell is placed on the selective solar absorber (SSA). In both cases the thermal and electrical efficiencies have been evaluated at different SSA operating temperatures, in the range of 323 K to 423 K. The analysis has been conducted at different energy bandgap (E_bg) of the PV cell and assuming a variable transmittance or emittance of the PV cell, depending on the design. The two systems efficiency comparison has been carried out at the same operating temperature. Overall, this work highlights the importance of high vacuum insulation, which guarantees the reduction of convective thermal losses, and shows that the maximum energy is produced for PV cells with E_bg ≈1.5-1.7 eV, depending on layout and operating temperature, by including the thermal output in the PV-T optimization. The energy and exergy efficiencies obtainable using the proposed PV-T systems are considerably improved compared to the results previously reported in the literature.

Voltage Stability & Control, is very crucial compared to other Power System (PS) Quality and Stability issues. Long-Vertical-Power-Flows in Conventional Grids, causes voltage drops which in turn causes huge power losses, especially in the Medium Voltage (MV) and Low Voltage (LV) Distribution Networks. Such technical losses in abysmally-planned weak distribution networks, lead to substantial loss of revenues to the utility grid. Apart from classic Voltage Regulation (VR) techniques, with the rise of Distributed Generation (DG) based on Renewable Energy Sources (RES), Horizontal-Power-Flows can be introduced in the network, through various Smart Grid techniques. Coupling such sources, near load centers shall mitigate long flows from expensive conventional sources at times of huge demands, improving feeders’ Voltage Profile. This Ancillary Service of Voltage Support from DG RESs shall thereby alleviate revenue losses caused by long-power-flows in weak distribution grids. For a developing country like Pakistan, loss of revenue from an already expensive utility gives huge blow to the economy. So, a similar technique for voltage support is proposed for an 11-kV feeder, which faces similar problem, and the results are remarkable. The technique is implemented using OpenDSS Tool by modelling 3MWp PV Penetration along with some future storage.

Herein is introduced a simple scalar field model derived from classical based kinetic energy, gravitational potential energy, and Special Relativity’s rest mass energy. By applying a classical orbit over the scalar field, relativistic effects are predicted. The scalar field is then applied to a classical model of the Hydrogen atom resulting in a relativistic effect equal to the binding energy of the Hydrogen atom. In addition, the model derives the fine structure constant due to the gravitational effect. The relativistic effects are then discretized in increments equal to the model’s gravitational induced constant. The discretization produces the Hydrogen atom spectral emissions and an angular moment equal to Planck’s reduced constant. The model is not presented as a replacement for current theory, rather it is for inspection and illustration of how a simplistic model may offer a fundamental bridge between the more complex, time proven theories of General Relativity and Quantum Mechanics.

A revised reversed Carnot cycle without external heat source and temperature gap is proposed to challenge the classic reversed Carnot cycle, heat pumps based on the proposed cycle with super energy efficiency works just like electric heater fitted for any climate including extreme cold weather, the application of these new heat pumps is discussed with conclusion that little real obstacles exist for scale application to address the heating related climate change, also a demonstration case shows a remarkable results to encourage the applications of these new heat pumps.

From the perspective of manufacturing companies, the political, media and economic discourse on decarbonisation of the recent years manifests itself as an increasing social expectation of action. In Germany in particular, this discourse is also being driven forward by powerful companies, respectively sectors, most notably the automotive industry. Against this background, it was examined how German manufacturing companies react to rising societal pressure and emerging policies. It is examined which measures the companies have taken or plan to take to reduce their footprint, which aspirations are associated with this and by which structural characteristics (company size, energy intensity, sector) these are influenced. A mix methods approach was applied, utilising data gathered from approx. 900 companies in context of the Energy Efficiency Index of German Industry (EEI), along with media research focusing on decarbonisation plans and initiatives announced. We demonstrate that one-size-serves-all approaches are not suitable to decarbonise industry as the situation and ambitions differ considerably depending on size, energy intensity and sector. Even though the level of ambition and urgency is high, particularly micro and energy intensive companies are challenged. The research uncovers a series of questions that call for attention to materialise the ambitions and address the challenges outlined.

Two-wheeler vehicles are the most significant mode of transportation for Kenyans in both rural and urban regions thereby contributing to local air pollution, and greenhouse gas emissions (GHG). The transition to electric two-wheeler vehicles can make a significant contribution to reducing GHG and improving the socio-economic lives of people living in rural Kenya. Re-newable energy systems can considerably contribute to the charging of electric two-wheeled vehicles, thus leading to the reduction of carbon emissions and the expansion of renewable energy penetration in rural Kenya. Therefore, this paper focuses on integrating and modelling electric two-wheeled vehicles (e-bikes) into an off-grid photovoltaic Water-Energy Hub located in the Lake Victoria Region of Western Kenya using the Conventional and Renewable Energy Opti-mization (CARNOT) Toolbox in MATLAB / Simulink. Electricity demand data obtained from the Water-Energy Hub was investigated and analysed. Potential solar energy surplus was identified and electric two-wheeler vehicles were integrated based on the surplus. A field measurement investigation on the energy consumption of the electric two-wheeler vehicles based on the rider’s driving behaviour was also carried. The annual electricity demand of 27,267 kWh, photovoltaic (PV) electricity production of 37,785 kWh with an electricity deficit of 370 kWh were obtained from the simulation results. To reduce the electricity deficit, a load optimisation algorithm was de-veloped to optimally integrate the electric 2-wheeler vehicle into the Water-Energy Hub. It was found that using the load optimisation algorithm, the annual electricity deficit was reduced to 1 kWh and the annual electricity demand was increased by 11% (30,767 kWh) which is enough to charge 4 additional electric two-wheeler batteries daily.

In this article, the main building of the former Uto City Hall, which was severely damaged in the 2016 Kumamoto earthquake, is investigated as a case study for the retrofitting of an irregular Reinforced Concrete building using the base-isolation technique. Its peak response is predicted via mode-adaptive bidirectional pushover analysis (MABPA), which was originally proposed by the authors. In the prediction step of MABPA, the peaks of the first and second modal responses are predicted considering the energy balance during a half cycle of the structural response. The numerical analysis results show that the peak relative displacement can be properly predicted by MABPA. The results also show that the performance of the retrofitted building models is satisfactory for the ground motion considered in this study, including the recorded motions in the 2016 Kumamoto earthquake.

Creep deformation behaviour in single phase γ-TiAl alloy has been an extensively studied topic since the late 1970s. A lot of literatures have reported creep behaviour of γ-TiAl alloys, manufactured using different processing techniques [1]–[7]. The present discussion revisits the original work on understanding the tensile creep deformation behaviour of wrought single-phase γ-TiAl alloy by Hayes et al. [8] and is aimed to develop an understanding of steady state creep, through strain vs strain rate and strain vs ln(strain rate) plots. Besides, it also attempts to study the variation of stress exponent with temperature between 760-900⁰C and also, to determine activation energies using the two most common approaches, namely: Zener-Hollomon (Z-H) [9] and Sherby-Dorn (S-D, temperature compensated time approach) [10] for stress levels of 69 and 103.4 MPa between 760-900⁰C.

Understanding of the decisive role of the interaction mechanism and kinetics in the combustion processes is highly relevant for the elaboration of optimal conditions for obtaining Mo-Cu composite powders. From this perspective, the efficient delivery of the reduction mechanism of copper and molybdenum oxides with combined Mg + C reducing agents at high heating rates is crucial to develop a valuable approach for the combustion synthesis of Mo-Cu composite powders. Herein, we shed light on the mechanism of the reactions in all the studied binary, ternary and quaternary systems contemporaneously demonstrating the effect of the heating rate on the conversion degree. The combination of two highly exothermic and speedy reactions (MoO3+3Mg and CuO+Mg vs MoO3+CuO+4Mg) led to a slow interaction with weak self-heating (dysynergistic effect) due to a change in the reaction mechanism. On the other hand, it has been shown that during the simultaneous utilization of the Mg and C reducing agents, the process begins exclusively with carbothermic reduction, and at relatively high temperatures it continues with magnesiothermic one. The effective activation energy values of the magnesiothermic stages of the studied reactions were determined by Kissinger isoconversional method.

Due to the increasing global importance of decarbonizing human activities, especially the production of electricity, the optimal deployment of renewable energy technologies will play a crucial role in future energy systems. To accomplish this, particular attention must be accorded to the geospatial and temporal distribution of variable renewable energy sources (VRES) such as wind and solar radiation in order to match electricity supply and demand. This study presents a techno-economical assessment of four energy technologies in the hypothetical context of Mexico in 2050, namely: onshore and offshore wind turbines, and open-field and rooftop photovoltaics. A land eligibility analysis incorporating physical, environmental, and socio-political eligibility constraints and individual turbine and photovoltaic park simulations, drawing on 39 years of climate data, is performed for individual sites across the country in an effort to determine the installable potential and the associated levelized costs of electricity. The results reveal that up to 54 PWh of renewable electricity can be produced as a cost of less than 70 EUR/MWh. Around 91% (49 PWh) of this would originate from 23 TW of open-field photovoltaic parks that could occupy up to 578,000 km2 of eligible land across the country. The remaining 9% (4.8 PWh) could be produced by 1.9 TW of onshore wind installations allocated to approximately 68,500 km2 of eligible land that is almost fully adjacent to three mountainous zones. The combination of rooftop photovoltaic and offshore wind turbines account for a very small share of less than 0.03% of the overall techno-economical potential.