We introduce a series of twisted donor-acceptor (D-A) carbazole-benzophenone based electroactive bipolar derivatives that were synthesized through the reaction of 4-fluorobenzophenone with various partially alkylated 3,3’-bicarbazoles. The comprehensive structural characterization of these compounds is provided. These amorphous materials exhibit suitable glass transition temperatures ranging from 57 to 102 °C and demonstrate high thermal stability, with decomposition temperatures reaching 400 °C. Moreover, the developed materials exhibit elevated photoluminescence quantum yields (PLQY) of up to 75.5% and favorable HOMO-LUMO levels, along with suitable triplet-singlet state energy values. Due to their good solubility and suitable film-forming properties, all the compounds were evaluated as blue emitters dispersed in 4,4’-bis(N-carbazolyl)-1,10-biphenyl (CBP) host for the fabrication of organic light-emitting diodes (OLEDs) in concentration dependent experiments. Among these experiments, the device containing 15 wt% of the guest 4-(9’-{2-ethylhexyl}-[3,3’]-bicarbazol-9-yl)benzophenone demonstrated the best characteristics, achieving maximum brightness of 3581 cd/m2, current efficiency of 5.7 cd/A, power efficiency of 4.1 lm/W and external quantum efficiency of 2.7%.

Designing high-voltage underground transmission lines poses complex challenges in heat management, trench optimization, and determining cable ampacity. This article introduces an innovative proposal that focuses on adjusting the dimensions of the thermal backfill as a primary strategy to enhance ampacity compared to the traditional approach of increasing the cross-sectional area of the cable core. The methodology employs a particle swarm optimization (PSO) technique with adaptive penalization, restart strategies, and parameter self-adaptation implemented in MATLAB. The objective of this approach is to provide more efficient solutions than traditional MATLAB PSO, demonstrating improved convergence and more accurate results with a success probability of 66.1\%. Although traditional PSO is 81\% faster, the proposed PSO stands out for its precision. Additionally, the incorporation of thermal backfill results in an 18.45\% increase in cable ampacity. Variations in the thermal resistivity of the soil, backfill, and ambient temperature are highlighted as sensitive factors affecting ampacity and backfill dimensions. This method is presented as a crucial tool in the early stages of the project and underground installation in operation with maximum ampacity, contributing to the continuous improvement of energy efficiency.

The thermal decomposition of siderite and its decomposition products in a vacuum atmosphere was investigated for the first time using in situ high-temperature transmission Mössbauer spectroscopy. These measurements were supported by X-ray diffraction, Raman spectroscopy, X-ray fluorescence, and magnetic measurements. In situ Mössbauer spectra were collected from room temperature (RT) to 750 oC with a temperature step of 50 oC. After that, the sample was cooled down to RT with step 100 oC. Raw siderite samples contain siderite as the only iron-bearing mineral, and after heating the samples at high temperatures, hematite and magnetite are only Fe-bearing phases. In the temperature range of 300 oC - 500 oC, siderite decomposition occurs. The analysis shows that siderite transforms directly into magnetite, and then hematite generation occurs as long as siderite is present in the sample. Changing hyperfine parameters like isomer shift, quadrupole splitting, or hyperfine magnetic field versus temperature were obtained for siderite and iron oxides (hematite, magnetite). The measurements also show that magnetite formed during the decomposition of siderite is a composition of particles of various sizes and a low degree of crystallization.

Indoor comfort is a critical determinant of the holistic educational experience, significantly influencing the well-being, concentration, and performance of students within the confines of school environments. Despite the widespread implementation of heating, ventilation, and air conditioning (HVAC) systems in educational institutions, achieving satisfactory thermal conditions, acceptable acoustics, and optimal daylight levels for occupants continues to pose a considerable challenge. In this review, we specifically delves into the parameters characterizing Italian school environments, recognizing their direct impact on students’learning and concentration. The primary objectives of this review are conducting a thorough examination of the current acustic conditions in Italian schools. The initial phase of our search strategy involved retrieving data from key databases, namely, Scopus, Web of Science, ScienceDirect, PubMed, and Google Scholar. Following the elimination of duplicate articles (n = 289), a total of 135 distinct papers remained for analysis. A critical review of the existing literature is presented based on these criteria, offering guidelines and recommendations for forthcoming studies. The critical review underscores various shortcomings in the current design, deployment, and documentation of multi-domain studies, signaling the need for enhanced quality in future research efforts.

Experimental measurement of porous polypropylene (PP) using the DTC-25 TA laboratory equipment and hot box test has been compared. The thermal conductivity of materials indicates the insulation capability of building materials. Excellent building materials will have a lower thermal conductivities value as well as other building insulator performance metrics. While results show that increasing the volume fraction of fluid in the porous PP has an inverse association with the thermal conductivity of the material as predicted by porous media theories, there is a marked difference in the measured values of the thermal conductivity using the two methods. The thermal conductivity values of porous from DTC-25 and hot box test were 0.21 and 0.0033 W/mK, respectively. The difference in the thermal conductivity values was due to the misapplication of the Fourier’s guarded heat flow model in the DTC-25 device to a convective fluid porous medium material.

The efficiencies of conventional triple organic Rankine cycle (TORC) configurations are restricted by the low critical temperatures of common working fluids (＜320 °C). This paper proposes a high-temperature TORC system. A near-azeotropic mixture biphenyl/diphenyl oxide (BDO), which has stellar track record in the high-temperature ORC applications, is innovatively adopted as the top and middle ORC fluid simultaneously. The top cycle evaporation temperature is up to 400 °C in view of BDO’s high stability. Five conventional organic fluids are chosen for the bottom ORC. Fundamentals of the TORC system are illustrated, and mathematical models are built. Thermo-economic performance is investigated. The results hint that the optimal thermodynamic property is achieved on the use of benzene as the bottom fluid. The maximum thermal and exergy efficiencies are respectively 40.86% and 74.14%. The largest irreversible loss occurs inside the heat exchanger coupling the middle and bottom ORCs, accounting for above 30% of the total entropy generation. The levelized energy cost (LEC) is 0.0284 $/kWh. Given the same heat source condition, the TORC system can boost efficiency by 1.02% and drive down LEC by 0.0024 $/kWh compared with a BDO mixture-based cascade ORC.

In recent years, the genesis of natural gas and the definition of major gas source rocks in the Baiyun Sag of the Pearl River Mouth Basin have attracted extensive attention from scholars. There is still considerable controversy over the genesis and the main gas source rocks of natural gas. In this study, the chemical kinetics method of natural gas generation and carbon isotope fractionation was used to study the generation history and isotope evolution history of Paleogene natural gas in the Y5 well area located on the north slope of Baiyun Sag. And other geochemical discriminant methods were applied simultaneously to determine the type and source rocks of natural gas. The results show that the natural gas in the Y5 well area on the northern slope of Baiyun Sag is mainly kerogen degradation gas, mixed with a small amount of oil cracking gas. The mixture of kerogen degradation gas and a small amount of crude oil cracking gas caused the inversion of the carbon isotope sequence of ethane and propane. The natural gas in the Y5 well area mainly comes from delta–shallow lacustrine facies source rock. The high–quality reservoirs in the shallower strata accumulate natural gas generated in the early stage, and the tight reservoirs in the deeper strata mainly accumulate natural gas generated in the late stage.

Key thermophysical properties necessary for the successful design and use of CoCrFeNi alloy in thermophysical applications have been measured experimentally, and the results have been compared with literature values and results previously obtained for commercial Ni-Cr alloys and equiatomic CoCrFeNi alloy. In particular, the thermal diffusivity, coefficient of thermal expansion (CTE), and specific heat capacity were measured for the as-cast and homogenized equiatomic CoCrFeNi alloy over a temperature range allowing the thermal conductivity to be calculated up to 1173 K. The thermal conductivity and thermal diffusivity of the equiatomic CoCrFeNi alloy were found to deviate from monotonic behavior in the temperature range from 773 to 1100 K. Such a deviation was previously observed in the behavior of the temperature dependence of CTE and specific heat capacity of the equiatomic CoCrFeNi alloy. The non-linear behavior is primarily the result of order/disorder phenomena for the as-cast and homogenized sample, as well as additionally for the as-cast sample, non-equilibrium solidification under arc melting conditions. The measured data of thermophysical properties are provided for thermally differently treated samples, and it is shown that there is a difference in the behavior of the temperature dependences of CTE, thermal diffusivity, and heat capacity.

In recent years, in order to serve as effective solutions to outdoor human thermal environments under the influence of urban heat islands, adaptation measures such as awnings, louvers, directional reflective materials, mist sprays, and evaporative materials have been developed. In this study, a simplified evaluation framework for adaptation measures to urban heat islands is examined. Adaptation measures to urban heat islands are classified into the following three categories; measures to reduce solar radiation incident on the human body, measures to control and cool ground and wall surface temperature, and measures to control and cool air temperature and human body. Case studies are conducted to evaluate the effects of the implementation of cool water circulation sunshade and to examine the adverse effects of cool pavements on the human thermal environment, in addition to the effects of mist sprays on the human body. The effect of the sunshade, watering road, and mist spray, which are typical adaptation measures to urban heat islands, on the human thermal environment was estimated using Wet Bulb Globe Temperature (WBGT) as an indicator for heat stroke prevention and Standard New Effective Temperature (SET*) as an indicator for thermal comfort assessment.

Sensor fusion algorithms and models have been widely used in recent times. Although research evidence has informed the use of sensor fusion models in diverse applications, there is room for improvement, especially in home-based health monitoring applications which require less supervision and technical knowledge of users. The present work compares data mining-based fusion software packages such as RapidMiner Studio, Anaconda, Weka, and Orange, and proposes a data fusion framework suitable for in-home applications. 574 privacy-friendly (binary) images and 1,722 datasets gleaned from thermal and Radar sensing solutions respectively, were fused using the software packages on instances of homogeneous and heterogeneous data aggregation. Experimental results indicated that the proposed fusion framework achieved an average Classification Accuracy of 84.7% and 95.7% on homogeneous and heterogeneous datasets respectively, with the help of data mining and machine learning models such as Naïve Bayes, Decision Tree, Neural Network, Random Forest, Stochastic Gradient Descent, Support Vector Machine, K-Nearest Neighbours and CN2 induction. Further evaluation of the sensor data fusion framework based on cross validation of features indicated average values of 94.4% for Classification Accuracy, 95.7% Precision and 96.4% for Recall.

This study investigates the contribution of nano-alumina (nA: 1-3wt.% binder) to the performance of silica fume (SF-10%) blended mortar in ternary blended mortar. The fresh (workability, setting time) and hardened properties (compressive strength and thermal resistance (300 °C for 1 h)), were examined. Nano alumina (nA) contributed positively to the consistency of SF blended mortar such that similar workability could be achieved with OPC when 3% nA was added. The initial and final setting time of 180 and 220 mins were recorded in SF blended mortar and reduced by 18.4 and 21.8%, respectively by adding 3%nA. The optimum mixture that contained 10%SF and 2%nA had 3-d and 28-d compressive strengths of 28 and 43.2 MPa. In the absence of nA, this reduced by 14.3% and 29.4% while it reduced by 25.2% and 16.7%, respectively in OPC mortar. The main products characterizing SF-nA ternary blended binder with dense microstructural density were nepheline and tobermorite. Besides, it is more susceptible to carbonation despite its superior performance in thermal resistance when compared to SF blended and OPC mortars.

The use of covers to protect blueberry orchards from adverse weather events has increased due to the variability in climate patterns, but the effects of rain cover and netting materials on yield and fruit quality have not been studied yet. This research evaluated the simultaneous effect of LDPE plastic cover, woven cover and netting materials on environmental components (UV light, PAR, NIR and growing degree days, GDD), plant performance (light interception, leaf area index, LAI, yield and flower development), and fruit quality traits (firmness, total soluble solids and acidity) in two blueberry cultivars. On average, UV transmission under netting was 11% and 43% higher compared to that under woven and LDPE plastic covers, while NIR was 8 -13% higher with both types of rain covers, with an increase in fruit air temperature and GDD. Yield was 27% higher under woven cover with respect to netting, but fruit firmness values under netting were 12% higher than those of LDPE plastic cover. Light interception, LAI and flower development explained 64% (p=0.0052) of the yield variation due to the cover material effect. The obtained results suggest that the type of cover differentially affects yield and fruit quality in blueberries due to the specific light and temperature conditions generated under these materials.

The production of anatase titanium dioxide particles plays a crucial role in the sulfate process used for manufacturing white pigment. A key factor in improving the quality of white pigments is enhancing the thermal mixing process within the precipitation tank. This improvement ensures the uniform dispersion of seed particles instead of their agglomeration, leading to the formation of particles with uniform sizes. The objective of this study was to enhance three-phase CFD simulations involving the mixing process of H₂SO₄ solution, steam as a gas phase, and solid seed particles. By analyzing the trajectories of the seed particles using CFD, the optimal injection position for the seed particles within the mixing process was determined. Subsequently, lab scale test and real field test were conducted based on the insights gained from the CFD simulations. The particle size distribution of two different types of seed inlets was analyzed and compared using Transmission Electron Microscopy (TEM). The findings of this study demonstrate that the developed multi-phase CFD simulation can be effectively utilized to enhance the precipitation process for the production of anatase titanium dioxide particles.

The condensing heat exchanger is commonly applied in various heat exchange systems. It can efficiently recover moisture and heat from the flue gas that contains water vapor. However, the convective-condensation heat transfer process is so complicated that no mature thermal calculation model is available. This study develops a thermal calculation model for the widely employed tubular condensing heat exchanger in industry. To characterize the degree of the heat and mass transfer, this study introduces two parameters, namely the sensible and latent heat transfer efficiencies of fin. The thermal calculations are conducted for the condensing heat exchangers reported in the literature to verify the proposed model by comparing it with the experimental data. The results show that the absolute error of the calculated sensible and latent heat transfer efficiencies is 0.0365 and 0.0268, respectively. Under the working conditions in this study, a maximum difference of 5.2 K has been acquired between the measured and calculated values of the outlet temperature. The relative error of the condensate water flowrate is mostly within ±5.0% and ±10.0% under the bare-tube and finned-tube conditions, respectively, with a maximum deviation of 0.7 and 1.4 kg h-1. This study provides a general model for designing and optimizing various tubular condensing heat exchangers accurately.

In a previous paper, we solved the partial differential equation of Mullins problem in the case of the evaporation-condensation in electronic devices and gave an exact solution relative to the geometric profile of the grain boundary grooving when materials are submitted to thermal and mechanical solicitation and fatigue effect. In this new research, new modelling of the grain groove profile was proposed and new analytical expressions of the groove profile, the derivative and the groove depth were obtained in the case of diffusion in thin polycrystalline films by the resolution of the fourth differential equation formulated by Mullins that supposed 〖y'〗^2≪1. The obtained analytical solution gave more accurate information on the geometric characteristics of the groove that were necessary to study the depth and the width of the groove. These new findings will open a new way to study with more accuracy the problem of the evaporation-condensation combined to the diffusion phenomenon on the material surfaces with the help of the analytical solutions.

Water pollution with dyes is a critical environmental issue because off the huge amount of dyes disbarred annually which cause severe damage for the ecosystem and human life. On the other hand, the core-shell based magnetic materials have showed amazing character for controlling the material synthesis with targeted structure to enhance the adsorptive-removal of pollutants. Herein, Fe3O4 core-TiO2/mesoSiO2 and Fe3O4 core-mesoSiO2/TiO2 double shell nanoparticles were prepared by first (R1) and second (R2) routes. The preparation procedure is controlled to prepare the magnetic core with further coating layers from silica and titania for the uptake of methylene blue from aqueous solutions. The reported adsorption capacities for R1-0.2, R1-0.4 and R2 samples were 46, 38 and 50 mg/g respectively at pH 6 after 80 min contact time form 50 ppm methylene blue solution. The adsorption process of methylene blue onto Fe3O4core-meso SiO2/TiO2 double shell was well fitted with the pseudo-second-order kinetic model and Freundlish isotherm which suggested the quick and multilayer adsorption mechanism. In addition, results of thermodynamic investigation indicated that the surfaces of Fe3O4 core-mesoSiO2/TiO2 and Fe3O4 core-TiO2/mesoSiO2 double shell exhibit spontaneous tendency to adsorb methylene blue from the aqueous solutions. These results will encourage the further application of Fe3O4 core-meso SiO2/TiO2 and Fe3O4 core-TiO2/meso SiO2 double shell for removal of other dyes and pollutants from wastewater.

Solid spent nuclear fuel from nuclear power plants has 3.4% fission products (80-160amu), contributing to over 99.8% radioactivity. On the other hand, liquid high-level radioactive waste (HLRW) from spent fuel reprocessing has 98.9% bulk elements (0-60amu) with 0.1% radioactivity. A separation mechanism on the mass categories as groups presents unique opportunities in managing HLRW for the long term with a considerable cost reduction. This paper proposes a thermal plasma-based separation system incorporating atmospheric pressure plasma torches for HLRW mass separation into low-resolution mass groups. Several engineering issues, such as waste preparation, waste injection into the plasma and waste collecting after mass separation, need to be addressed. Using COMSOL Multiphysics simulation, the generic system can be studied using noble gas mass separation and further analyze the mass filter capabilities. This paper provides the history of plasma-based mass separation. Functional modelling of a thermal plasma mass separation system is proposed under atmospheric pressure. Finally, aspects of mass separation simulation using noble gas Argon and Helium inside the plasma mass separation system were studied in COMSOL Multiphysics.

In metal continuous casting process is important to estimate the temperature evolution of casted section along machine from meniscus (point in which liquid metal is poured) to cutting machine where product is cut at commercial length. Particularly in the case of large sections, a convenient approximated model to achieve this goal with a feasible computational effort, is the so called travelling slice: the transversal section of casted product is subjected to different thermal boundary conditions (e.g. thermal flux, radiation, convection) that are found during the movement at constant speed from meniscus to the end of machine. In the case of an axisymmetric section, a comparison with the exact solution can be easily achieved. The article will show pros and cons of both, namely the far lower computational cost of travelling slice model without losing precision. Results confirm the validity of the travelling slice approach also at low casting speed and huge dimensions.

During the last years, the increasing evidence of dietary antioxidant compounds and reducing chronic diseases and the relationship between diet and health have promoted an important innovation on the baked product sector, aiming at healthier formulations. This study aims to develop a tool based on mathematical models to predict baked goods total antioxidant capacity (TAC). The high variability of antioxidant properties of flours based on the aspects related to type of grains, varieties, proximal composition and processing, among others, makes very difficult to innovate on food product development without specific analysis. Using Total phenol content (TP), Oxygen radical absorbance capacity (ORAC) and Ferric reducing antioxidant power assay (FRAP) as proxies of antioxidant capacity. Three Bayesian-type models are proposed based on a double exponential parameterised curve that reflects the initial decrease and subsequent increase as a consequence of the observed processes of degradation and generation, respectively, of the antioxidant compounds. Once the values of the main parameters of each curve have been determined, support vector machines (SVR) with exponential kernel were used to predict, based on the temperature and duration of baking as well as the values of proteins and fibers of each native grain, the values of TAC during the baking time.

A series of alpha,omega-bis(o-methoxyphenyl)arenes were prepared through Suzuki-Miyaura coupling reactions of dibromoarenes with o-methoxyphenyl boronic acid. P2O5-CH3SO3H-mediated direct polycondensation of alpha,omega-bis(o-methoxyphenyl)arenes with trans-1,4-cyclohexanedicarboxylic acid proceeded regioselectively to afford 1,4-cyclohexanediyl-containing aromatic polyketones. The resulting aromatic polyketones have high Tg and excellent solubility in typical organic solvents. In addition, the polyketone films fabricated by solution casting method are more colorless and transparent than those without cyclohexanediyl units.

Thermal treatment in Australia is gaining interest due to legislative changes, waste reduction goals, and the need to address contaminants risks in biosolids used for agriculture. The resulting biochar product has the potential to be beneficially recycled as a soil amendment. On-farm management practices were reviewed to identify barriers that need to be overcome to increase recycling and examine the role of pyrolysis and gasification in effectively improving the quality and safety of biochar. Key findings revealed: (1) thermal treatment can effectively eliminate persistent organic pollutants, microplastics and pathogens, and (2) more than 90% of the total heavy metals content in biosolids become immobilized when these are converted to biochar, thus reducing their bioavailability following land application. While reported research on the short-term effects of biosolids-derived biochar suggested promising agronomic results, there is dearth of information on long-term effects. Other knowledge gaps include optimisation of land application rates, understanding of rate of breakdown and fate of contaminants in soil and water, heavy metal mobility in soil and bioaccumulation or transfer to the food chain. Improved understanding of nutrients and contaminants dynamics in soils receiving biosolids-derived biochar is a pre-requisite for their safe use in Australian agriculture, and therefore it is highlighted as priority area for future research.

The administration of regional neuraxial analgesia for pain relief during labor is widely recognized as a safe and effective method involving medication delivery into the epidural or subarachnoid space in the lower back. This study proposes an innovative semantic image segmentation methodology emphasizing enhanced interpretability using convolutional Random Fourier Features and layer-wise weighted class-activation maps tailored explicitly for foot segmentation in regional analgesia monitoring. Namely, our contribution is twofold: i) a novel Random Fourier Features layer is introduced to deal with image data to enhance three well-known architectures (FCN, UNet, and ResUNet); ii) three novel quantitive measures are presented to evaluate the interpretability of a given deep learning model devoted to segmentation tasks. Our approach is rigorously evaluated on a demanding dataset of foot thermal images from pregnant women who received epidural anesthesia. Its small size and considerable variability characterize the dataset. Our validation results demonstrate that the proposed methodology not only achieves competitive foot segmentation performance but also significantly enhances the explainability of the process, rendering it well-suited for applications such as epidural insertion during labor.

This work exclusively focuses on the assessment of the thermal performance of a multifunctional facade panel incorporating PCM in foam layers, recurring to a hot box heat flux meter method to determine the thermal transmittance (U-value). The experimental setup is based on the steady-state approach using climatic chambers, assuring a stable thermal environment. Even small fractions of PCM achieved a small reduction in thermal amplitude. Numerical simulations using Ansys Fluent were developed to evaluate the performance of PCM use over a wide range of temperature boundary conditions and operating modes. These numerical models were calibrated and validated using the results of experimental tests, achieving a correlation factor of 0.9674, thus accurately representing a real-world scenario. The decrement factor (f) was used to analyse the data. It was identified that the efficiency of the panel and size of the optimum region increased with the PCM fraction growth. The simulated behaviour was optimum when the input mean temperature is of 20 °C for a room temperature of between 18-20 °C. The results show the significant potential of the multi-layered panel and the thermal regulator effect of the PCM incorporated on indoor space temperature to reach good thermal comfort levels.

The central coast is one of the importantly livable regions in China, and green land plays a meaningful role in improving human settlements through regulating ecosystem services. However, the research on spatiotemporal heterogeneity of green land in different urbanized areas are still lacking in this region, which limits the timeliness of reporting on the land-surface thermal properties of residential environment from green land perspective. To address this issue, the synergistic methodology of “artificial numerical technology -- urban interior mixed pixel classification -- surface radiation energy balance model” was applied to investigate the green land change and its impact on human settlements in Rizhao region, which is known for its coastal ecology and greenery in China and obtained the United Nations habitat award. Main conclusions of this study are below: (1) Although total green land decreased by 474.05 km2, resulting in a decrease of 9.17% in its share of the entire study area from 2000-2022 during the urbanization process, but the greening levels improved within the built-up area, with the greening proportion of 25.34% in 2000 and 42.98 km2 in 2022. (2) Differences in green land at different urbanized regions were first observed, namely, urban greening rate was 37.78% in the old urban areas of 2022, while it was up to 46.43% in new urban areas. More attention was paid to the construction of urban green space during urban expansion, which will inevitably bring better visual and comfort experience to residents. (3) Thermal comfort indicators for urban residents were evaluated in latent heat flux (0-457.83 W/m2), sensible heat flux (0-645.09 W/m2), total available energy (254.07-659.42 W/m2) and others. (4) The lowered cooling temperature effect in the middle, high green land density region was 1.05 ℃ and 2.12 ℃ compared to the low-density region, and the average air temperature was 25.86 ℃. Also, spatial patterns of hot and cold uncomfortable areas were displayed in this study. Overall, this study provides the meaningfully practical reference for exploring the spatiotemporal heterogeneity of green land and its impact on residents' environments from the perspective of land-surface thermal properties in coastal areas of China and around the world.

Using number theory, a formula is obtained that describes the thermal conductivities of ZrC, UC, UN, ThN, ZrN and Th_xU_1-xN at x = 0.2 and 0.5 with temperature change. This formula contains the atomic numbers of the elements, the thermal conductivities of the individual elements of the substance, and the structural parameter. There is no direct dependence on temperature in the formula, since it is hidden in the thermal conductivities of each element and in the structure parameter. In some temperature ranges, the structural parameter is constant; therefore, the thermal conductivity of some carbides and nitrides is expressed through summing the thermal conductivities of individual elements.

In this contribution, we make an attempt to write a theoretical proposal for designing an eco friendly thermal power plant which runs with cold nuclear fusion technology at a temperature of (1500 to 2000) deg.C. In our recently published papers, we have proposed a clear cut mechanism for understanding and implementing cold nuclear fusion technique pertaining to fusion of hydrogen with metals of mass numbers starting from 50. In this context, we would like to stress the point that, fusion of hydrogen under controllable temperature and pressure can be understood as a phenomenon of fusing neutron to the nucleus of the base atom. Part of isotopic nuclear binding energy difference of final and base atomic nuclides can be seen in the form of safe thermal energy of the order of (1 to 3) MeV per atom against 200 MeV released in nuclear fission of one Uranium atom. Due to increased heaviness and weak interaction, sometimes fused neutron splits into proton and electron. Proton seems to be retained by the base atom’s nuclear core and electron seems to join with the electronic orbits of the base atom. In this way, increased mass of base atomic nuclide helps in eco friendly production of thermal energy in large quantity. For this purpose we consider Iron-56 as a fuel. In a simplified view, under strong nuclear attractive forces, Iron-56 absorbs hydrogen atom as a neutron and by emitting 1MeV equivalent thermal energy transforms to Iron-57. Thus, one gram of Iron-56 can generate 1000MJ of heat with 50% efficiency. In a shortcut approach, by bombarding powder and semi-liquid forms of Iron-56 with direct neutrons coming from neutron source, our proposal can be tried, understood and verified experimentally.

This work aims to investigate systematically the tecno-economic feasibility of ther-mos-catalytic cracking process for two solid waste materials, a lipid-base material (re-sidual fat/scum from retention box of the University Restaurant of UFPA) and a lig-nin-cellulosic material Açaí seed (Euterpe oleracea. Mart). The thermo-catalytic process-es were carried out in pilot scale (THERMTEK/LEQ/UFPA/IME/RJ), and their economic feasibility analyzed. The yields of biofuels produced by fractional distillation were al-so studied. The physicochemical characteristics of the raw materials, the organic liquid product (bio-oil) and the chemical composition of kerosene, light-diesel and heavy-diesel from the lipid-base material, as well as those of kerosene and light-diesel from the Açaí seed were also determined. The economic indicators for the evaluation of the most viable cracking (pyrolysis) and distillation process of bio-oils were: a) the sim-ple payback criterion, b) discounted payback, c) net present value (NPV), d) internal rate of return (IRR), and e) index of profitability (IP). The analysis of the indicators showed the economic viability of crude palm oil (Elaeis guineensis, Jacq) and unfeasibil-ity for the palm oil neutralization. The minimum fuel selling price (MFSP) obtained is this work for the biofuels was of 1.34 US$/L) and the breakeven point obtained was of 1.28 US$/L. The sensibility analysis demonstrated that the pyrolysis and distillation yields are the most important variables to affect the minimum fuel selling price (MFSP).

This work aims to investigate the effect of process temperature and catalyst content by pyrolysis and thermal catalytic cracking of (organic matter + paper) fraction from municipal household solid waste (MHSW) on the yields of reaction products (bio-oil, bio-char, H2O, and gas), acid value and chemical composition of bio-oils, and characterization of bio-chars, in laboratory scale. The collecting sectors of MHSW in the municipality of Belém-Pará-Brazil were chosen based on geographic and socio-economic database. The MHSW collected and transported to the segregation area. The gravimetric analysis of MHSW carried out and the fractions (Paper, Cardboard, Tetra Pack, Hard Plastic, Soft Plastic, Metal, Glass, Organic Matter, and Inert) separated. The selected organic matter and paper submitted to pre-treatment of crushing, drying, and sieving. The experiments carried out at 400, 450, and 475 °C and 1.0 atmosphere, and at 475 °C and 1.0 atmosphere, using 5.0, 10.0, and 15.0% (wt.) Ca(OH)2, in batch mode. The bio-oil characterized for acid value. The chemical functions present in bio-oil identified by FT-IR and the composition by GC-MS. The bio-char characterized by SEM, FT-IR and XRD. The variance in mass (wt.%) for organic fraction of municipal household solid waste, between 56.21 and 67.45% (wt.), lies with the interval of 56% (wt.) and 64% (wt.) of OFMHSW for middle and low income countries. The pyrolysis of MHSW fraction (organic matter + paper) show bio-oil yields between 2.63 and 9.41% (wt.), aqueous phase yields between 28.58 and 35.08% (wt.), solid phase yields between 35.29 and 45.75% (wt.), and gas yields between 16.54 and 26.72% (wt.). The bio-oil yield increases with pyrolysis temperature. For the catalytic cracking, the bio-oil and gas yields increase slightly with CaO content, while that of bio-char decreases, and the H2O phase remains constant. The GC-MS of liquid reaction products identified the presence of hydrocarbons (alkanes, alkenes, alkynes, cycloalkanes, and aromatics) and oxygenates (carboxylic acids, ketones, esters, alcohols, phenols, and aldehydes), as well as compounds containing nitrogen, including amides and amines. The acidity of bio-oil decreases with increasing process temperature and with aid Ca(OH)2 as catalyst. The concentration of hydrocarbons in bio-oil increases with increasing Ca(OH)2-to-MHSW fraction ratio due to the catalytic deoxygenation of fatty acids molecules, by means of de-carboxylation/de-carbonylation, producing aliphatic and aromatic hydrocarbons.

This work aims to investigate the effect of catalyst content and reaction time by catalytic upgrading from pyrolysis vapors of residual fat at 450 °C and 1.0 atmosphere, on the yields of reaction products, physicochemical properties (density, kinematic viscosity, refractive index, and acid value) and chemical composition of organic liquid products (OLP), over a catalyst fixed bed reactor, in semi pilot scale. Pellets of Red Mud chemically activated with 1.0 M HCl were used as catalysts. The experiments were carried out at 450 °C and 1.0 atmosphere, using a process schema consisting of a thermal cracking reactor of 2.0 L coupled to a catalyst fixed bed reactor of 53 mL, without catalyst and using 5.0, 7.5, and 10.0% (wt.) Red Mud pellets activated with 1.0 M HCl, in batch mode. Samples of liquid phase products were withdrawn during the course of reaction at 40, 50, 60, 70 and 80 min in order to analyze the process kinetics. The physicochemical properties (density, kinematic viscosity, acid value, and refractive index) of OLP were determined by official methods. The chemical functions present in OLP determined by FT-IR and the chemical composition by GC-MS. The thermal catalytic cracking of residual fat show OLP yields from 54.4 to 84.88 (wt.%), aqueous phase yields between 2.21 and 2.80 (wt.%), solid phase yields (coke) between 1.30 and 8.60 (wt.%), and gas yields from 11.61 to 34.22 (wt.%). The yields of OLP increases with increasing catalyst content while those of aqueous, gaseous and solid phase decreases. For all the thermal and thermal catalytic cracking experiments, the density, kinematic viscosity, and acid value of OLP decreases with increasing reaction time. The GC-MS of liquid reaction products identified the presence of hydrocarbons (alkanes, alkenes, cycloalkanes, and aromatics) and oxygenates (carboxylic acids, ketones, esters, alcohols, and aldehydes). For all the thermal and thermal catalytic cracking experiments, the hydrocarbon content within OLP increases with reaction time, while those of oxygenates decrease, reaching concentrations of hydrocarbons up to 95.35% (area.). The best results for the physicochemical properties (density, kinematic viscosity, and acid value) and the maximum hydrocarbon content of OLP were obtained at 450 °C and 1.0 atmosphere, using a catalyst fixed bed reactor, with 5.0% (wt.) Red Mud pellets activated with 1.0 M HCl as catalyst.

This paper considers the general ocean circulation within the thermodynamical closure of our climate theory, which aims to deduce the generic climate state from first principles. The preceding papers of the theory have reduced planetary fluids to warm/cold masses and determined their bulk thermal properties, which provide prior constraints for the derivation of the upper-bound circulation when the potential vorticity is homogenized in moving masses. In a companion paper on the atmosphere, this upper bound is seen to reproduce the prevailing wind, forsaking therefore previous discordant explanations of the easterly trade and the polar jet stream. In this paper on the ocean, we again show that this upper bound may replicate broad features of the observed circulation, including a western-intensified subtropical gyre and a counter-rotating tropical gyre feeding the equatorial undercurrent. Together, we posit that PV homogenization may provide a unifying dynamical principle of the large-scale planetary circulation, which may be interpreted as the maximum macroscopic motion extractable by microscopic stirring --- within the confine of the thermal differentiation.

Introduction: Heat is a kinetic process whereby energy flows from between two systems; hot-to-cold objects. In oro-dental implantology, conductive heat transfer/(or thermal stress) is a complex physical phenomenon to analyze and consider in treatment planning. Hence, ample research has attempted to measure heat-production to avoid over-heating during bone-cutting and -drilling for titanium (Ti) implant-site preparation and insertion, thereby preventing/minimizing early (as well as delayed) implant-related complications and failure. Objective: Given the low bone-thermal conductivity whereby heat generated by osteotomies is not effectively dissipated and tends to remain within the surrounding tissue (peri-implant), increasing the possibility of thermal-injury; this work attempts to obtain an exact analytical solution of the heat equation under exponential thermal-stress, modeling transient heat transfer and temperature changes in Ti implants upon hot-liquid intake. Materials and Methods: We investigate the impact of the material, the location point along implant length, and the exposure time of the thermal load on temperature changes. Results: Despite its simplicity, the presented solution contains all the physics and reproduces the key features obtained in previous numerical analyses studies. To the best of knowledge, this is the first introduction of the intrinsic time, a “proper” time that characterizes the geometry of the dental implant, where we show, mathematically and graphically, how the interplay between “proper” time and exposure time influences temperature changes in Ti implants, under the suitable initial and boundary conditions. Conclusions: This work aspires to accurately complement the overall clinical diagnostic and treatment plan for enhanced bone-implant interface, implant stability and success rates, whether for immediate or delayed loading strategies.

Multilayer absorbers based on Cr2O3 and Cr, designed to improve the Solar-to-thermal conversion efficiency at mid temperatures in high vacuum flat thermal panel, are fabricated via sputtering deposition on bulk copper substrates and characterized by thermal and optical analysis. The refractive index of the single layers has been measured and used to estimate absorber thermal efficiency at the operating temperatures. Multilayers have been produced via sputtering deposition on bulk copper substrates. The absorber multilayers can be 10% more efficient than the commercial alternative at 250 °C operating temperatures, reaching 380 °C stagnation temperature without Sun concentration. The thermal stability has been checked at temperature of 400 °C in vacuum for four hours. High vacuum flat thermal collectors, equipped with the produced selective solar absorbers can obtain unprecedented performances and can give important contribution to the energy transition from fossil fuels to renewable energy for efficient heat production.

Electric heating and solid thermal storage system (EHSTSS) is widely used in district clean heating and the flexibility adjustment of combined heat and power (CHP) unit. It has been an effective way to absorb renewable energy. Aiming at the thermal design calculation and experimental verification of EHSTSS, the thermal calculation and the heat transfer characteristics of the EHSTSS are investigated in this paper. Firstly, a thermal calculation method for the EHSTSS is proposed in the paper. The calculation flow and calculation method for key parameters of heating system, heat storage system, heat exchange system and fan-circulating system in the EHSTSS are studied. Then, the instantaneous heat transfer characteristics of the thermal storage system (TSS) in the EHSTSS are analyzed, and the heat transfer process of ESS is simulated by FLUENT software. The uniform temperature distribution in the heat storage and release process of the TSS verifies the good heat transfer characteristics of the EHSTSS. Finally, EHSTSS test verification platform is built, and the historical operation data of the EHSTSS is analyzed. During the heating and release thermal process, the maximum temperature standard deviation of each temperature measurement point is 28.3℃ and 59℃respectively. The correctness of the thermal calculation of the EHSTSS is verified.

Energy efficiency of Data Center (DC) operations heavily relies on IT and cooling systems performance. A reliable and efficient cooling system is necessary to produce a persistent flow of cold air to cool servers that are subjected to constantly increasing computational load due to the advent of IoT- enabled smart systems. Consequently, increased demand for computing power will bring about increased waste heat dissipation in data centers. In order to bring about a DC energy efficiency, it is imperative to explore the thermal characteristics analysis of an IT room (due to waste heat). This work encompasses the employment of an unsupervised machine learning modelling technique for uncovering weaknesses of the DC cooling system based on real DC monitoring thermal data. The findings of the analysis result in the identification of areas for energy efficiency improvement that will feed into DC recommendations. The methodology employed for this research includes statistical analysis of IT room thermal characteristics, and the identification of individual servers that frequently occur in the hotspot zones. A critical analysis has been conducted on available big dataset of ambient air temperature in the hot aisle of ENEA Portici CRESCO6 computing cluster. Clustering techniques have been used for hotspots localization as well as categorization of nodes based on surrounding air temperature ranges. The principles and approaches covered in this work are replicable for energy efficiency evaluation of any DC and thus, foster transferability. This work showcases applicability of best practices and guidelines in the context of a real commercial DC that transcends the set of existing metrics for DC energy efficiency assessment.

Uniform illumination is a key requirement in different research fields. However, this requirement is often difficult to achieve when high intensity is required at the same time. Recent advancements in LED lamps allow nowadays for compact and economical solutions. In this work we present a suitable solution for various laboratory purposes requiring stable, uniform and high intensity illumination. The system is composed of four identical high power white LED arrays of 30 mm diameter each, placed on a supporting and cooling structure having a minimum volume of 26 cm x 26 cm x 8 cm. A numerical model has been developed, based on a ray tracing software, in order to simulate the performances. These have then been experimentally validated with measurements of the power density map, carried out with a 1% uncertainty pyranometer. Data show that the built system is very stable over time and provides an illumination uniformity higher than 98%, on a surface of 50 mm radius, which reduces to 95% on a surface of 75 mm radius. The power density can be adjusted in the 390-1360 W m-2 range, not affecting uniformity.

In this work, a xylan-based antimicrobial additive agent was prepared and aimed for uses in paper products against Escherichia coli bacteria. The derived Cationic-Xylan-grafted-PHGH (CX-g-PHGH) was successfully synthesized by graft copolymerization of cationic-xylan with guanidine polymer (PHGH) using ceric ammonium nitrate as initiator. The obtained CX-g-PHGH had maximum PHGH grafting ratio of 18.45% and efficiency of 58.45%, and showed good viscosity and thermal stability. Furthermore, the paper samples prepared in this work were reinforced obviously with the addition of CX-g-PHGH by improved mechanical properties. Compared to the reference paper without any of the xylan-derivatives, the index of tensile, tear, burst and folding endurance of the paper had increases up to 20.07%, 25.31%, 30.20% and 77.78%, respectively. Moreover, the prepared CX-g-PHGH paper exhibited an efficient antimicrobial activity against E. coli bacterial, by which a lot of applications based on the new xylan-derived additive agent obtained in this work could be found, especially in field of antimicrobial paper products against E. Coli bacteria from contaminated food.

A new di-mannitol adipate ester-based zinc metal alkoxide (DMAE-Zn) was synthesized as a bi-functional PVC thermal stabilizer for the first time. The materials were characterized with Fourier-transform Infrared spectroscopy (FT-IR) and thermogravimetric analysis (TGA). Characterization results confirmed the formation of Zn-O bonds in DMAE-Zn; and that DMAE-Zn had a high decomposition temperature and a low melting point. The thermal stability of DMAE-Zn on PVC also was tested by conductivity test, thermal aging test, and UV-visible spectroscopy (UV-VIS) test. PVC stabilized by DMAE-Zn had a good initial color and excellent long-term stability. UV-VIS also showed that the conjugated structure in PVC stabilized by DMAE-Zn was almost all of the triene, suggesting that the addition of DMAE-Zn would suppress the formation of conjugated structures above tetraene. Dynamic processing performance of PVC samples tested by torque rheometer indicated that, having a good compatibility with PVC chains in the amorphous regions, DMAE-Zn contributed good plasticizing effect to PVC. DMAE-Zn thus effectively demonstrates bi-functional roles, e.g., thermal stabilizers and plasticizers to PVC. Furthermore, FT-IR, HCl absorption capacity test, and complex ZnCl₂ test were also used to verify the thermal stability mechanism of DMAE-Zn for PVC.

High-resolution laboratory-based thermal infrared spectroscopy is an up-and-coming tool in the field of geological remote sensing. Its spatial resolution allows for detailed analyses at centimeter to sub-millimeter scale. However, this increase in resolution creates challenges with sample characteristics such as grain size, surface roughness and porosity that can influence the spectral signature. This research explores the effect of rock sample surface preparation on the TIR spectral signatures. We applied three surface preparation methods (split, saw and polish) to determine how the resulting differences in surface roughness affects both the spectral shape as well as the spectral contrast. The selected samples are a pure quartz sandstone, a quartz sandstone containing a small percentage of kaolinite, and an intermediate-grained gabbro. To avoid instrument or measurement type biases we conducted measurements on three TIR instruments, resulting in directional hemispherical reflectance spectra, emissivity spectra and bi-directional reflectance images. Surface imaging and analyses were performed with scanning electron microscopy and profilometer measurements. We demonstrate that surface preparation affects the TIR spectral signatures influencing both the spectral contrast as well as the spectral shape. The results show that polished surfaces predominantly display a high spectral contrast while the sawed and split surfaces display up to 25% lower reflectance values. Furthermore, the sawed and split surfaces display spectral signature shape differences at specific wavelengths, which we link to mineral transmission features, surface orientation effects and multiple reflections in fine-grained minerals. Hence, the influence of rock surface preparation should be taken in consideration to avoid an inaccurate geological interpretation.

Precast concrete sandwich panels (PCSP) are energy efficient building system that is achieved through an insulation layer created between the concrete wythes. The insulation layer is usually of low bearing strength material making it more applicable for non-structural building systems. Hence, shear connectors are introduced to improve its structural capacity, which subsequently degrades it thermal performance by serving as thermal bridges across the panel. This article review researches of alternative materials and methods used to improve the thermal efficiency as well as reduced the strength loss due to insulation in PCSP. The alternative materials are basalt fibre reinforced polymer (BFRP), carbon fibre reinforced polymer (CFRP), glass fibre reinforced polymer (GFRP), and foam concrete which are selected due to their low thermal conductivity for use in shear connection. While thermal path method has been used to prevent the effect of thermal bridges. Although, some of these materials have successfully achieved the desirable behaviours, however, several undesirable properties such as brittleness, bond slip, the sudden crushing of the panel system, and FRP failure below its ultimate strength were observed. Hence, the practicality of the alternative materials is still questionable despite its higher cost compared to the conventional steel and concrete used in the PCSP system.

In the first part of this talk we review some prerequisites for and essential arguments involved in the construction of the thermal-ground-state estimate for the deconfining phase in the thermodynamics of SU(2) Quantum Yang-Mills theory and how this structure supports its distinct excitations. The second part applies deconfining SU(2) Yang-Mills thermodynamics to the Cosmic Microwave Background in view of (i) a modified temperature-redshift relation with an interesting link to correlation-length criticality in the 3D Ising model, (ii) the implied minimal changes in the dark sector of the cosmological model, and (iii) best-fit parameter values of this model when confronted with the spectra of the angular two-point functions TT, TE, and EE, excluding the low-$l$ physics. The latter, which is treated in an incomplete way because of the omission of radiative effects, is addressed in passing towards future work.

Most of the phase change materials (PCMs) have been limited to use as functional additions or sealed in containers, and extra auxiliary equipment or supporting matrix is needed. The emergence of 3D printing technique has dramatically advanced the developments of materials and simplified production processes. This study focuses on a novel strategy to model thermal energy storage crystalline gels with three-dimensional architecture directly from liquid resin without supporting materials through light-induced polymerization 3D printing technique. A mask-projection stereolithography printer was used to measure the 3D printing test, and the printable characters of crystalline thermal energy storage P(SA-DMAA) gels with different molar ratios were evaluated. For the P(SA-DMMA) gels with small fraction of SA, the 3D fabrication was realized with higher printing precision both on mili- and micro-meter scales. As a comparison of 3D printed samples, P(SA-DMAA) gels made by other two methods, post-UV curing treatment after 3D printing and UV curing using conventional mold, were prepared. The 3D printed P(SA-DMAA) gels shown high crystallinity. Post–UV curing treatment was beneficial to full curing of 3D printed gels, but did not lead to the further improvement of crystal structure to get higher crystallinity. The P(SA-DMAA) crystalline gel having the highest energy storage enthalpy that reached 69.6 J·g⁻¹ was developed. Its good thermoregulation property in the temperature range from 25 to 40 °C was proved. The P(SA-DMAA) gels are feasible for practical applications as one kind of 3D printing material with thermal energy storage and thermoregulation functionality.

Long-term durability of the vacuum edge-seal plays a significant part in retrofitting triple vacuum glazing (TVG) to existing buildings in achieving towards zero-energy buildings (ZEB) target. Vacuum pressure decrement with respect to time between panes affect the thermal efficiency of TVG. This study reports a 3D finite element model, with validated mathematical methods and comparison, for the assessment of the influence of vacuum pressure diminution on the thermal transmittance (U value) of TVG. The centre-of-pane and total U values of TVG calculated to be 0.28 Wm⁻²K⁻¹ and 0.94 Wm⁻²K⁻¹ at the cavity vacuum pressure of 0.001 Pa. The results suggests that a rise in cavity pressure from 0.001 Pa to 100 kPa increases the centre-of-pane and total U values from 0.28 Wm⁻²K⁻¹ and 0.94 Wm⁻²K⁻¹ to 2.4 Wm⁻²K⁻¹ and 2.58 Wm⁻²K⁻¹, respectively. The temperature descent on the surfaces of TVG between hot and cold sides’ increases by decreasing the cavity vacuum pressure from 50 kPa to 0.001 Pa. To maintain the cavity vacuum pressure of 0.001 Pa for over 20 years of life span in the cavity of 10 mm wide edge sealed triple vacuum glazing, non-evaporable getters will maintain the cavity vacuum pressure that will enable the long-term durability to TVG.

Blood perfusion quantification is important vital parameters in different diagnostic procedure, using infrared thermography imaging; it is reliable to use this technique as non-contact, non-invasive blood flow measurement method. Therefore, we developed a measurement protocol for blood flow over the arm's anterior surface. By using the superficial brachial and radial veins to be monitored under the impact of cold-excitation of (2 °C to 5 °C), the blood perfusion signal was detected using thermal imager of long-wave infrared spectral range (LWIR, 7μm - 14 μm). The simulation of Penne's bioheat transfer equation was performed to be compared with results obtained from the infrared thermography. Furthermore, the proposed blood flow monitoring using external adjusting of the excitation temperature, by using (cold-compress, or cold air-stream) applied to the region under testing. The signal detected resembles to the hemodynamic pulse of the superficial veins, in the definition of systolic and diastolic phases of the cardiac cycle. Moreover, statistical analysis applied to the BFIRT signals from 24 subjects to estimate the skin's mean temperature after recovery from the thermal excitation.

In this paper, we investigate the stabilization of a one-dimensional thermoelastic laminated beam with structural damping, coupled to a heat equation modeling an expectedly dissipative effect through heat conduction governed by Gurtin-Pipkin thermal law. Under some assumptions on the relaxation function g, we establish the well-posedness for the problem. Furthermore, we prove the exponential stability and lack of exponential stability for the problem. To achieve our goals, we make use of the semigroup method, the perturbed energy method and Gearhart-Herbst-Prüss-Huang theorem.

Li-ion cell designs, component integrity and manufacturing processes all have critical influence on the safety of Li-ion batteries. Any internal defective features that induce a short circuit, can trigger a thermal runaway: a cascade of reactions, leading to a device fire. As consumer device manufacturers push aggressively for increased battery energy, instances of field failure are increasingly reported. Notably Samsung made a press release in 2017 following a total product recall of their Galaxy Note 7 mobile phone, confirming speculation that the events were attributable to the battery and its mode of manufacture. Recent incidences of battery swelling on the new iPhone 8 have been reported in the media, and the techniques and lessons reported herein may have future relevance. Here we look deeper into the key components of one of these cells and confirm evidence of cracking of electrode material in tightly folded areas, combined with a delamination of surface coating on the separator, which itself is an unusually thin monolayer. We report microstructural information about the electrodes, battery welding attributes and thermal mapping of the battery whilst operational. The findings point to the most likely combination of events and highlights the impact of design features, whilst providing structural considerations most likely to have led to the reported incidences relating to this phone.

Land Surface Temperature (LST) is routinely retrieved from remote sensing instruments using semi-empirical relationships between top of atmosphere (TOA) radiances and LST, using ancillary data such as total column water vapor or emissivity. These algorithms are calibrated using a set of forward radiative transfer simulations that return the TOA radiances given the LST and the thermodynamic profiles. The simulations are done in order to cover a wide range of surface and atmospheric conditions and viewing geometries. This work analyses calibration strategies, considering some of the most critical factors that need to be taken into account when building a calibration dataset, covering the full dynamic range of relevant variables. A sensitivity analysis of split-windows and single channel algorithms revealed that selecting a set of atmospheric profiles that spans the full range of surface temperatures and total column water vapor combinations that are physically possible seems beneficial for the quality of the regression model. However, the calibration is extremely sensitive to the low-level structure of the atmosphere indicating that the presence of atmospheric boundary layer features such as temperature inversions or strong vertical gradients of thermodynamic properties may affect LST retrievals in a non-trivial way. This article describes the criteria established in the EUMETSAT Land Surface Analysis – Satellite Application Facility to calibrate its LST algorithms applied both for current and forthcoming sensors.

The aim of this study is to investigate transient dynamic flow characteristics of the fluid flow through 5-way electric coolant valve (PCCV : Penta-Control Coolant Valve). To achieve this goal, the present paper attempts the three-dimensional dynamic simulation of the fluid flow through the valve using a commercial CFD solver with moving mesh technique to consider flow inertia and dynamic flow in the opening and closing stages of the ball valve rotating motion. Firstly, dynamic flow characteristics and the thermal mixing inside the PCCV ball valve during the opening and closing stage was analyzed. It is found that the discrepancies between dynamic and steady state simulation is remarkable when fluxes with different levels of enthalpy and momentum flow into the PCCV leads to strong flow interference and flow inertia, while the discrepancies are relatively small at low rotation speed and weak flow interference. Then, the effect of dynamic flow characteristics of the valve on dynamic thermal mixing characteristics at two different ball valve rotational speeds and rotational directions were investigated. It was found that the dynamic flow and thermal mixing characteristics inside the PCCV are greatly affected by the rotation speed, rotation direction, and degree of flow interference between fluxes. It is helpful for the design of the better coolant control strategies and the improvement of the FCEV thermal management system.

This study examined the effects of blending decanol, an oxygenated fuel, with diesel on diesel engine performance and emissions. Experiments were conducted on a single-cylinder engine at 1700 rpm and 2700 rpm, using diesel/decanol blends at 10%, 30%, and 50% by volume (D90de10, D70de30, D50de50). Results showed that brake thermal efficiency decreased with higher decanol ratios at low speeds. In contrast, brake specific fuel consumption and brake specific energy consumption increased due to decanol's lower calorific value. Regarding emissions, decanol blending reduced NOx, CO, HC, and smoke. NOx emissions were lowered by the cooling effect resulting from decanol's higher latent heat of vaporization and lower calorific value, especially at low speeds. CO and HC emissions declined as decanol's oxygen content promoted oxidation, reducing incomplete combustion. Smoke emissions were minimized in fuel-rich zones by preventing unburned carbon particle formation. This study highlights decanol's potential as an eco-friendly diesel blending option. Future work should optimize blending ratios and injection settings to enhance diesel engine performance.

Heat exchangers play a vital role in numerous sectors like power generation and automotive manufacturing. Enhancing the energy efficiency of these exchangers stands as a significant hurdle. Utilizing nanofluids emerges as an optimal solution to augment heat transfer rates, leveraging their superior thermal conductivity while addressing economic constraints linked with traditional heat exchanger technologies. The motivation for this study is to consider the comprehensive synergistic features of MWCNTs, SiO₂, and hybrid MWCNTs–SiO₂ EG-based nanofluids in plate heat exchangers. This was achieved by simulating a plate heat exchanger using CFD (Fluent and Gambit softwares) considering the comparison of two SiO₂, MWCNTs, and their hybrid forms at different mass concentrations. The Reynolds-Averaged Navier-Stokes (RANS) method was employed to model turbulent flows, and the nanoparticles were compared in both single-phase and two-phase states, with their properties derived from experimental studies. Moreover, Nusselt number, convective heat transfer coefficient, and pressure drop variations were computed at different Reynolds numbers. The findings indicated an increase in the Nusselt number with the incorporation of the hybrid nanofluid, achieving a maximum enhancement of 11.19% in comparison to EG at a Reynolds number of 240 and a concentration of 0.86 wt.%. Noticeably, the pressure drop remained negligible at lower Reynolds numbers, exhibiting marginal variations up to 0.3% at higher Reynolds numbers. At a concentration of 0.86 wt.% and a Reynolds number of 480, the introduction of MWCNTs, hybrid, and SiO₂ nano-additives resulted in respective increases in the heat transfer coefficient by 21.02%, 10.76%, and 2.16% and corresponding alterations in pressure drop of 0.11%, 0.04%, and 0.02%.

Demographic studies have revealed a strong association between exposure to high ambient temperatures during pregnancy and increased risks of preterm birth (PTB). The mechanism underlying this association is unclear, but it is plausible that altered placental function may contribute. In this study, we conducted differential gene expression analysis, gene set enrichment analysis (GSEA), and gene ontology (GO) analysis on bulk RNA-seq data from human placentas delivered at term and preterm during the warmer months compared to placentas delivered at term and preterm during the colder months in the UK. We detected 48 differentially expressed genes in preterm placentas delivered during the warmer months compared to preterm placentas delivered during the colder months, the majority of which were inflammatory cytokines and chemokines, including SERPINA1, IL1B, CCL3, CCL3L3, CCL4, CCL4L2, CCL20, and CXCL8. The GSEA positively enriched 17 signalling pathways, including the NF-κB, IL17, toll-like receptor, and chemokine signalling pathways, in warm-exposed preterm placentas, which were not observed in warm-exposed term placentas. The GO analysis revealed several biological processes, including neutrophil, granulocyte, monocyte, and lymphocyte chemotaxis, as well as inflammatory and humoral immune responses in warm-exposed preterm placentas, but not in warm-exposed term placentas. We conclude that maternal exposure to warm environmental temperatures during pregnancy alters the placental transcriptome towards inflammation and immune regulation, potentially leading to PTB.

In this study, we explored the manipulation of optical properties in the terahertz (THz) frequency band of radio-frequency (RF) sputtered indium-tin-oxide (ITO) thin-films on highly resistive silicon substrate by rapid thermal annealing (RTA). The optical constants of as-deposited and RTA-processed ITO films annealed at 400°C, 600°C and 800°C are determined in the frequency range of 0.2 to 1.0 THz. The transmittance can be changed from ~ 27% for as-deposited to ~ 10% and ~ 39% for ITO films heat-treated at different annealing temperatures, T_a’s. Such variations of optical properties in the far infrared for the samples under study are correlated with their mobility and carrier concentration, which are extracted from Drude-Smith modeling of THz conductivity with plasma frequency, scattering time and the c-parameters as fitting parameters. Resistivities of the films are in the range of 10^-3 to 10^-4 W-cm, confirming that annealed ITO films can potentially be used as transparent conducting electrodes for photonic devices operating at THz frequencies. The highest mobility, m = 47 cm²/V∙s, with carrier concentration, N_c = 1.31´10²¹ cm^-3, was observed for ITO films annealed at T_a = 600°C. The scattering times of the samples were in the range of 8 – 21 fs, with c-values of -0.63 to -0.87, indicating strong back scattering of the carriers, mainly by grain boundaries in the polycrystalline film. To better understand the nature of these films, we have also characterized the surface morphology, microscopic structural properties and chemical composition of as-deposited and RTA-processed ITO thin-films. For comparison, we have summarized the optical properties of ITO films sputtered on fused silica substrates, as-deposited and RTA-annealed, in the visible transparency window of 400-800nm. The optical bandgaps of the ITO thin films were evaluated with a Tauc plot from the absorption spectra.

This study evaluates the viability of n-octanol as an alternative fuel in a direct-injection diesel engine, aiming to enhance sustainability and efficiency. Experiments employed varying blends of n-octanol (10%, 30%, and 50% by volume) with pure diesel, analyzing impacts on engine performance and emissions. The methodology involved testing each blend in a single-cylinder engine, measuring engine performance parameters such as brake torque and brake power under full load conditions across an engine speed range from 1400 to 2500 rpm. Comparative assessments of performance and emission characteristics at a constant engine speed of 1700 rpm were also conducted with varying loads. Results indicated that while n-octanol blends consistently improved brake thermal efficiency, they also increased brake specific fuel consumption due to the lower energy content of n-octanol. Consequently, while all n-octanol blends reduced nitrogen oxides (NOx) emissions compared to pure diesel, they also significantly decreased carbon monoxide, hydrocarbons, and smoke opacity, presenting a comprehensive reduction in harmful emissions. However, the benefits came with nuanced trade-offs: notably, higher concentrations of n-octanol (especially the 50% blend) led to a relative increase in NOx emissions as the octanol ratio increased. The study concludes that n-octanol significantly improves engine efficiency and reduces diesel dependence, but optimizing the blend ratio is crucial to balance performance improvements with comprehensive emission reductions.

The quiet-time solar wind electrons feature non-thermal characteristics when viewed from the perspective of their velocity distribution functions. They typically have an appearance of being composed of a denser thermal “core” population plus a tenuous energetic “halo” population. At first, such a feature was empirically fitted with the Kappa velocity space distribution function, but ever since the ground-breaking work by Tsallis, the space physics community has embraced the potential implication of the Kappa distribution as reflecting the non-extensive nature of the space plasma. From the viewpoint of microscopic plasma theory, the formation of non-thermal electron velocity distribution function can be interpreted in terms of the plasma being in a state of turbulent quasi equilibrium. Such a finding brings forth the possible existence of a profound inter-relationship between the non-extensive statistical state and the turbulent quasi-equilibrium state. The present paper further develops the idea of solar wind electrons being in the turbulent equilibrium, but unlike the previous model, which involves the electrostatic turbulence near the plasma oscillation frequency (i.e., Langmuir turbulence), the present paper considers the impact of transverse electromagnetic turbulence, particularly, the turbulence in the whistler-mode frequency range. It is found that the coupling of spontaneously-emitted thermal fluctuations and the background turbulence leads to the formation of non-thermal electron velocity distribution function of the type observed in the solar wind during quiet times. This demonstrates that the whistler-range turbulence represents an alternative mechanism for producing the Kappa-like non-thermal distribution, especially close to the Sun and in the near-Earth space environment.

The transition of the energy system to renewable sources means the cheap energy storage in fossil fuels must be replaced by other options. A large part of the demand for useful energy is heat and cold, often produced from electric energy by a resistance heater, compression heat pump or cooler. The question is then to store the initial electric energy by electric energy storage (EES) or the useful energy by thermal energy storage (TES). In a desktop study both options were compared, by the choice made in existing applications, and also generally analyzing current technology data. For the latter, cost, round-trip efficiencies, life cycles and life time of EES, specifically for batteries, and of TES, specifically for hot and cold water, ice and other PCM were collected. Applications studied are heating and cooling in buildings and in industry. Application-typical conversion efficiencies were also collected and taken into account. The results show that in many existing installations TES, incl. by PCM, is already preferred, and that TES is advantageous in most investigated applications economically, in addition to technical advantages. Thus, TES has a large potential in the transition of the energy system to stabilize the electricity grid by demand side management.

High Vacuum Flat Plate Collectors (HVFPCs) are the only type of Flat Plate Thermal Collectors capable of producing thermal energy for middle-temperature applications (until 180 °C). As the trend of research plans to develop new Selective Solar Absorbers to extend the range of HVFPC application until 250 °C, it is necessary to correctly evaluate the collector efficiency up to such temperature to predict the energy production accurately. We propose an efficiency model for these collectors based on the selective absorber optical properties. The proposed efficiency model explicitly includes the radiative heat exchange with the ambient, which is the main source of thermal losses for evacuated collectors at high temperatures. It also decouples the radiative losses that depend on the optical properties of the absorber adopted from the other thermal losses due to HVFPC architecture. The model has been validated by applying it to MT-Power HVFPC manufactured by TVP-Solar, and it has been used to predict the efficiency and energy production of HVFPC equipped with new, optimized selective solar absorbers developed in recent years.

Generally, mineral fillers are added to thermoplastic polymers to reduce cost and improve performance. However, properly selected mineral fillers can also improve thermal conductivity and deformation behavior, shrinkage, impact strength, dimensional stability, and molding cycle time in thermoset polymers. This study focused on the preparation and microscopic and spectroscopic characterization of various hybrid composites using pumice as primary filler and gypsum, kaolin and hollow glass sphere as secondary fillers, as well as examining some of their mechanical properties and thermal conductivities. For this, first of all, surface modification of the clay was carried out by intercalation method from solution using raw Montmorillonite, cationic surfactant and long chain hydrocarbon material, and then organo-clay melamine formaldehyde nanocomposite was prepared by in situ synthesis using organo clay and melamine formaldehyde pre-polymer. Finally, non-ionic surfactant, foaming agent and glycerin were added to the prepared nano-composite at approximately 90°C, mixed mechanically and then pumice was added. The processes at this stage were repeated while preparing hybrid composites with pumice and other mineral additives. For curing and molding, the composite was first subjected to microwave irradiation for 5 minutes followed by thermal treatment at 140°C for 60 min. Fourier transform infrared spectroscopy (FTIR), X-ray powder diffraction (XRD) spectra and Scanning electron microscope (SEM) and High resolution transmission electron microscope (HRTEM) images were taken for morphological and textural characterization for raw clay (MMT), organo clay (OMMT) and pure polymer with prepared hybrid composites. In addition, some mechanical properties such as bending strength, elasticity modulus and screw holding resistance, as well as thermal conductivity coefficients of the hybrid composites were determined according to the relevant standards and the obtained results were evaluated. Spectroscopic and microscopic analyzes have shown that effective adhesion interactions occur between polymer-clay nanocomposite particles and filler grains, thus resulting in textural arrangements with different properties. Mechanical and thermal conductivity test results showed that melamine formaldehyde-organo-clay nano composite foam and hybrid composite containing hollow glass sphere are highly qualified materials in terms of thermal insulation and mechanical strength.

We have investigated the effect of electron-beam irradiation by a forevacuum-pressure plasma-cathode electron source on the surface roughness and hardness of Al2O3- and AlN-based ceramics. The roughness increases with increasing temperature of the processed surface, while the hardness slightly decreases. For aluminum nitride ceramic, we find that the thermal conductivity increases by a factor of 1.5 to 2 depending on the electron-beam irradiation regime.

in order to enhance the separation performance and to reduce the heat loss of the transmembrane for membrane distillation, the thermal efficiency and hydrophobicity of the membrane distillation should be simultaneously enhanced. In this work, a PVDF/PET hydrophobic/hydrophilic membrane is prepared by non-solvent phase inducing method. Nanosized silica aerogel (SiAG) with high porosity is added to the composite membranes. The modifying effects and operating conditions on permeate flux and thermal efficiency in direct contact membrane distillation (DCMD) are investigated. Furthermore, the latent heat of vaporization and the heat transfer across the membranes are compared for SiAG addition, which indicates that the composite PVDF@SiAG/PET membranes display a great potential for distillation-separation application with high heat efficiency.

Solar heating technology is a promising solution to promote China to achieve the “3060 double carbon” target as soon as possible. And seasonal thermal storage (STS) can effectively solve the mismatch problem of solar heating systems between the supply and demand of thermal energy. Due to the instability of solar radiation resources and heat demand, it is necessary to analyze the dynamic response characteristics of the system. Yet, related studies are still scarce. In this study, a solar heating system with a solar tower receiver and STS was introduced in north China. The dynamic performance of the system is analyzed with a dynamic simulated method in a typical day or typical operation modes, and the switch mechanism between multiple operation modes is also revealed. The impact of different heating strategies on system performance was analyzed. Results showed that the solar fraction of the system reached 89.4% in the third year, which was 3.6% higher than the first year. The quality-quantity heating operation strategies can be effective ways to improve the discharge efficiency of STS and the system performance without any heat pump. The electricity consumption of the pump on the heating side could be significantly reduced by 44.6% compared with the quality control.

: Electric air conditioning and heating systems capacity is growing rapidly. So does the nameplate capacity of PV power plants. While demand in cooling has a positive correlation with solar irradiationirradiance, the demand in heating has an opposite relation. In this study, different approaches of to design (aggregation; energy storagethermal, battery and implicit systems storage) and control (frequency conversion; variable and adaptive load) and their effects on the efficiency of an off-grid active thermal stabilisation system based on a solar-powered heat pump are analysed. The case considered is permafrost thermal stabilisation system in Norway. It is shown that proper layout and control of the system with an adaptive load can reduce the capital expenses expenditures and the total cost of ownership by 30-40%. Increase in the efficiency capacity factor and cooling stability of the systems with the aggregated and threshold power consumervariable load due to the principle of aggregation is studied. The downside of that is the increase in compressors operation time by 50% with variable load and by 25% per unit with aggregation which means more frequent replacement in terms of motor-hours. But The the feasibility of this approaches considered are applicable for a wide range of solar-powered facilities, but the results are is quite case sensitive and depends on the prices for low-power heat pumps. The prospects of using the excess refrigerant and soil for thermal energy storage instead of traditional electrochemical batteries are considered.

This work presents a design and model of the thermo-hydrodynamic behavior applying CFD for pin-fin heat sink with square shape (rectangular fin profile), through a novel pin arrangement that improves heat removal in the system. The novelty consist in the insertion of a deflector row that will help to direct the flow, so it hits the rectangular cross-sectional fins the presents in the system. The heat sink model is placed in channel designed in which air flows as suitable medium, and its overall performance is investigated. In addition, a constant heat flux is applied to the bottom wall of the heat sink model, equal values and amounts that​ correspond to the heat fluxes generated by current electronic equipment and devices. The numerical results of the global thermal resistance, the pressure drop and the Nusselt number are reported. The results allow determining best arrangement or geometry configuration, location and functionality of the fin-deflectors were collocated for evaluate thermal-hydraulic efficiency of system.

Fungal infection of grape berries (Vitis vinifera) by Botrytis cinerea frequently coincides with harvest, impacting both the yield and quality of grape and wine products. A rapid and non-destructive method for identifying B. cinerea infection in grapes at an early stage prior to harvest is critical to manage loss. In this study, zeolitic imidazolate framework-8 (ZIF-8) crystal was applied as an absorbent material for volatile extraction from B. cinerea-infected and healthy grapes in a vineyard followed by thermal desorption gas chromatography-mass spectrometry. The performance of ZIF-8 to absorb and trap targeted volatiles was evaluated with a standard solution of compounds and with a whole bunch of grapes enclosed in a glass container to maintain standard sampling conditions. Results from sampling methods were then correlated to B. cinerea infection in grapes as measured and determined by Genus specific antigen quantification. Trace levels of targeted compounds reported as markers of grape B. cinerea infection were successfully detected with in-field sampling. Peak area counts for volatiles 3-octanone, 1-octen-3-one, 3-octanol, and 1-octen-3-ol extracted using ZIF-8 were significantly higher than values achieved using Tenax®-TA from field testing and demonstrated good correlation with B. cinerea infection severities determined by B. cinerea antigen detection.

The sustainable development of innovative eco-friendly multifunctional nanocomposites, possessing superior characteristics, is a noteworthy topic. Novel semi-interpenetrated nanocomposite films based on poly(vinyl alcohol) covalently and thermally crosslinked with oxalic acid (OA), reinforced with a novel organophosphorus flame retardant (PFR-4) derived from co-polycondensation in solution reaction of equimolar amounts of co-monomers, namely, bis((6-oxido-6H-dibenz[c,e][1,2]oxaphosphorinyl)-(4-hydroxyaniline)-methylene)-1,4-phenylene, bisphenol S, and phenylphosphonic dichloride, in a molar ratio of 1:1:2, and additionally doped with silver-loaded zeolite L nanoparticles (ze-Ag), have been prepared by casting from solution technique. The morphology of the as prepared PVA-oxalic acid films and their semi-interpenetrated nanocomposites with PFR-4 and ze-Ag was investigated by scanning electron microscopy (SEM), while the homogeneous distribution of the organophosphorus compound and nanoparticles within the nanocomposite films has been introspected by means of energy dispersive X-ray spectroscopy (EDX). It was established that composites with a very low phosphorus content had noticeably improved flame retardancy. The peak of the heat release rate was reduced up to 55%, depending on the content of the flame retardant additive and the doping ze-Ag nanoparticles introduced into the PVA/OA matrix. The ultimate tensile strength and elastic modulus increased significantly in the reinforced nanocomposites. Considerably increased antimicrobial activity was revealed in the case of the samples containing silver-loaded zeolite L nanoparticles.

The work is devoted to the search for effective solutions to the applied problem of early diagnostics of plant stress in the conditions of smart farming and based on modern explicable artificial intelligence (XAI). The study mostly oriented on the theory and practice of XAI, focused on the use of hyperspectral imagery (HSI) and Thermal Infra-Red (TIR) sensor data at the input of a neural network. The first our goal is to build an XAI neural network, explainable due to its structure, the input of which is a datascientist oriented HSI 'explanator', and the output is a biologist oriented TIR 'explanator'. In the middle is SLP-regressor which solves the universal problem of training HSI pixels to temperatures of plants, needed for early plant stress diagnostic. The result can be considered as prototype of a special XAI explanator which is assigned to transform explanator specialized on area 1 onto explanator specialized on area 2. Using this HSI-TIR explanator we ensured the follows: extend HSI data by TIR attribute; providing TIR data for early diagnostic of plant stress; reducing dimensionality HSI needed for TIR training 25 times (from 204 to 8) preserving the same accuracy of temperature prediction (RMSE=0.2-0.3C). This reducing was achieved without using PCA methods. The constructed model is computationally efficient in training: the average training time is significantly less then 1 min (Intel Core i3-8130U, 2.2 GHz, 4 cores, 4 GB). One of the 8 channels, 820 nm, is the leader in correlation with TIR, what allows building local linear temperature prediction functions.

This work aims to investigate the influence of reaction time and catalyst-to-residual fat ratio by catalytic upgrading from pyrolysis vapors of residual fat at 400 °C and 1.0 atmosphere, on the yields of reaction products, physicochemical properties (density, kinematic viscosity, and acid value) and chemical composition of bio-oils, over a catalyst fixed bed reactor of activated carbon pellets impregnated with 10.0 M NaOH, in semi pilot scale. The experiments were carried out at 400 °C and 1.0 atmosphere, using a process schema consisting of a thermal cracking reactor of 2.0 L coupled to a catalyst fixed bed reactor of 53 mL, without catalyst and using 5.0, 7.5, and 10.0% (wt.) activated carbon pellets impregnated with 10.0 M NaOH, in batch mode. Samples of liquid phase products were withdrawn during the course of reaction at 50, 60, 70, 80, 90, 100 and 120 minutes in order to investigate the process kinetics. The physicochemical properties (density, kinematic viscosity, and acid value) of bio-oils were determined by official methods. The chemical composition of bio-oils determined by GC-MS. The thermal catalytic cracking of residual fat show bio-oils yields from 55.55 to 30.22 (wt.%), aqueous phase yields between 2.83 and 3.19 (wt.%), solid phase yields between 13.56 and 9.75 (wt.%), and gas yields from 27.89 to 55.60 (wt.%). The yields of bio-oil decreases from 74.41 to 30.22% (wt.) with increasing catalyst-to-Tallow kernel oil ratio, while that of gaseous phase increases from 12.87 to 55.60% (wt.). For all the thermal and thermal catalytic cracking experiments, the density, kinematic viscosity, and acid value of bio-oils decreases as the reaction time increases varying from 0.9266 to 0.8220 g/cm³, 8.10 to 2.24 mm²/s, and 144.14 to 2.37 mg KOH/g. The GC-MS of liquid reaction products identified the presence of hydrocarbons (alkanes, alkenes, ring-containing alkanes, ring-containing alkenes, and aromatics) and oxygenates (carboxylic acids, ketones, esters, alcohols, and aldehydes). For all the pyrolysis and catalytic cracking experiments, the hydrocarbon selectivity in bio-oil increases with increasing reaction time, while those of oxygenates decrease, reaching concentrations of hydrocarbons up to 95.35% (area.). The best results for the physicochemical properties density, kinematic viscosity, and acid value were 0.8220 g/cm³, 3.03 mm2/s, and 2.37 mg KOH/g, respectively, with a maximum hydrocarbon concentration of 97.194% (area.) and 2.806% ketones (area.) were obtained at 400 °C and 1.0 atmosphere, 80 minutes, without catalyst. For the catalytic cracking experiments, the maximum hydrocarbon content of 75.763% (area.) and 17.041% (area.) carboxylic acids, 4.702% (area.) ketones (area.), and 2.494% (area.) non-identified oxygenates was obtained at 400 °C and 1.0 atmosphere, 90 minutes, using a catalyst fixed bed reactor, with 10.0% (wt.) activated carbon pellets impregnated with 10.0 M NaOH as catalyst.

Highly nonlinear characteristics of lithium-ion batteries (LIBs) are significantly influenced by the external and internal temperature of the LIB cell. Moreover, cell temperature beyond the manufacturer’s specified safe operating limit could lead to thermal runaway and even fire hazards and safety concerns to operating personnel. Therefore, accurate information of cell internal and surface temperature of LIB is highly crucial for effective thermal management and proper operation of a battery management system (BMS). Accurate temperature information is also essential to BMS for the accurate estimation of various important states of LIB such as state of charge, state of health and so on. High capacity LIB pack, used in electric vehicles and grid-tied stationary energy storage system essentially consists of thousands of individual LIB cells. Therefore, installing a physical sensor at each cell especially at the cell core is not practically feasible from the solution cost, space and weight point of view. A solution is to develop a suitable estimation strategy which led scholars to propose different temperature estimation schemes aiming to establish a balance among accuracy, adaptability, modelling complexity and computational cost. This article presented an exhaustive review of these estimation strategies covering recent developments, current issues, major challenges, and future research recommendations. The prime intention is to provide a detailed guideline to the researchers and industries towards developing a highly accurate, intelligent, adaptive, easy to implement and compute efficient online temperature estimation strategy applicable to health-conscious fast charging and smart onboard BMS.

In roll-to-roll (R2R) processing, uniformity of the web is a crucial factor that can guarantee high coating quality. To understand web defects due to thermal deformation, we analyzed the effects of web unevenness on the coating quality of an yttria-stabilized zirconia (YSZ) layer, a brittle electrolyte of solid oxide fuel cells (SOFCs). We used finite element analysis to analyze the thermal and mechanical deformations at different drying temperatures. A YSZ layer was also coated using R2R slot-die coating to observe effects of web unevenness on the coating quality. It was seen that web unevenness was generated by thermal deformation due the conduction and convection heat from the dryer. Owing to varying web unevenness with time, the YSZ layer developed cracks. At higher drying temperatures, more coating defects having larger widths were generated. Results indicated that web unevenness at the coating section led to coating defects, which could damage the SOFC and decrease its yield in the R2R process. From this study, we suggest that coating defects, generated by the web unevenness owing to the convection and conduction heat, should be considered for the high-volume production of brittle electrolytes using the R2R process.

Land Surface Temperature is a one of the key variable of Global climate changes and model which estimate radiating budget in heat balance as control of climate model. It is a major influenced factor by the ability of the surface emissivity. In this study, were used Landsat 8 satellite image that have Operational Land Imager and Thermal Infrared Sensor to calculate Land Surface Temperature through geospatial technology over Ampara district, Sri Lanka. The Land Surface Temperature was estimated with respect to Land Surface Emissivity and Normalized Difference Vegetation Index values determined from the Red and Near Infrared channels. Land Surface Emissivity was processed directly by the thermal Infrared bands. Pixels based calculation were used to effort at LANDSAT 8 images that thermal Band 10 various dates in this study. The results were achievable to compute Normalized Difference Vegetation Index, Land Surface Emissivity, and Land Surface Temperature with applicable manner to compare with land use/ land cover data. It determines and predicts the changes of surface temperature to favorable to decision making process for the society. Study area faces seasonal drought in Sri Lanka, the prediction method that how land can be efficiently used with the present condition. Therefore, the Land Surface Temperature estimation can prove whether new irrigation systems for agricultural activities or can transformed source of energy into useful form that introducing solar hubs for energy production in future.

Mineral wool made from basalt fibers is frequently used as an insulating material in construction systems. In this study, both unused mineral wool, and wool obtained from the softened roofing area, were comprehensively analyzed in a laboratory using different characterization techniques. Firstly, the amount of initial water content and compressive strength at 10% deformation were determined. Secondly, microstructure and surface chemical composition were analysed by Scanning electron microscopy (SEM) equipped with energy dispersive x-ray spectroscopy (EDX). To study heterogeneities near the fiber surface and to examine cross-sectional composition, a Scanning transmission electron microscope (STEM) was used. Finally, to verify possible reasons for resin degradation, Thermogravimetry analysis and differential scanning colometry (TGA-DSC) were simultaneously carried out. The results show that natural aging under high humidity and thermal fluctuations greatly affects the surface morphology and chemical composition of fibrous composite. Phenol-formaldehyde and other hydrophobic compounds that protect fibers against moisture and give compressive resistance were found to be degraded.

Tree nuts show nutritional properties and human health benefits. However, they contain allergenic proteins, which make them harmful to the sensitised population. The presence of tree nuts on food labelling is mandatory and, consequently, the development of suitable analytical methodologies to detect nuts in processed foods is advisable. Real-time PCR allowed a specific and accurate amplification of allergen sequences. Some food processing methods could induce structural and/or conformational changes in proteins by altering their allergenic capacity, as well as produce the fragmentation and/or degradation of genomic DNA. In this work, we analysed by means of Real-time PCR, the influence of pressure and thermal processing through Instant Controlled Pressure Drop (DIC) on the detectability of hazelnut,pistachio and cashew allergens have been tested. The detection of targets in hazelnut, pistachio and cashew (Cor a 9, Pis v 1 and Ana o 1, respectively) is affected by the treatment, in different extent depending on the tree nut. Results are compared to those previously obtained by our group in the analysis of different treatments on the amplificability of the same targets. Reduction in amplificability is similar to that reported for some autoclave conditions. Our assays might allow detecting up to 1000 mg/kg of hazelnut, pistachio and cashew flours after being submitted to DIC treatment in food matrices.

Façade elements are a building component that satisfies multiple performance parameters. Among other things, “advanced façades” take advantage of hybrid solutions, such as assembling laminated materials. In addition to the enhanced mechanical properties that are typical of optimally composed hybrid structural components, these systems are energy-efficient, durable, and offer lighting comfort and optimal thermal performance, an example of which is the structural solution developed in collaboration with the University of Zagreb and the University of Ljubljana within the Croatian Science Foundation VETROLIGNUM project. The design concept involves the mechanical interaction of timber and glass load-bearing members without sealing or bonding the glass-to-timber surfaces. Following earlier research efforts devoted to the structural analysis and optimization of thus-assembled hybrid Cross-Laminated Timber (CLT)-glass façade elements, in this paper, special focus is given to a thermal and energy performance investigation under ordinary operational conditions. A simplified numerical model representative of a full-size building is first presented by taking advantage of continuous ambient records from a Live-Lab mock-up facility in Zagreb. Afterwards, a more detailed Finite Element (FE) numerical analysis is carried out at the component level to further explore the potential of CLT–glass façade elements. The collected numerical results show that CLT–glass composite panels can offer stable and promising thermal performance for façades similar to national and European standard requirements.

Facade elements are known to represent a building component with multiple performance parameters to satisfy. Among others, “advanced facades” take advantage of hybrid solutions, like the assemblage of laminated materials. In addition to enhanced mechanical properties that are typical of optimally composed hybrid structural components, these systems are energy-efficient, durable, and offer lightening comfort and optimal thermal performance. This is the case of the structural solution developed in joint research efforts of the University of Zagreb and the University of Ljubljana, within the Croatian Science Foundation VETROLIGNUM project. The design concept involves the mechanical interaction of timber and glass load-bearing members, without sealing or bonded glass-to-timber surfaces. Laminated glass infilled timber frames are recognized as a new generation of structural members with relevant load-carrying capacity (and especially the enhancement of earthquake resistance of framed systems), but also energy-efficient and cost-effective solutions.

In this study, the properties of unsaturated polyester resin were studied in the presence of recycled ceramic waste particles. Herein, composites were created that contained 28.5-50 wt% porcelain particles (particle size <180 µm). High filler contents increased the gel time and decreased the exotherm temperature of unsaturated polyester resin during curing. The obtained results showed that physical parameters, such as the resin density and porosity, increased as the filler content increased. In addition, the X-ray diffraction results indicated that the produced samples were a combination of ceramic waste particles and unsaturated polyester resin, resulting in semi crystalline structure. The results showed that the maximum water absorption at 40°C increased from 0.97 to 1.5% as the filler content increased from 28.5 to 50 wt%; in this process, the materials experienced a color change but did not lose mechanical performance. Finally, the samples were characterized by thermogravimetric analysis (TGA) to study the effect of porcelain powder on the thermal degradation of the resin. The TGA scans were analyzed with the Friedman method. The results indicated that the samples with porcelain powder exhibited substantially better thermal stability than unsaturated polyester resin.

In thermal friction drilling (TFD) operations, the geometrical dimensions of bushing shape, height and wall thickness are the most vital consequences, due to increasing the connecting length and strength. In this paper, AA7075-T651 aluminum alloys with 2, 4, 6, 8, and 10 mm in thicknesses were drilled with TFD process in order to investigate the density, the volume ratio, and height and wall thickness of the bushings. The experiments were conducted at constant spindle speed and feed rate conditions by using HSS conical tools of 5, 10, 15, and 20 mm in diameters. It was experimentally found that the bushing height and the wall thickness were tendency of increase linearly with increasing both material thickness and tool diameter. The effect of tool diameter was found to have much of influence on the measured values than the thickness of the drilled material. The density of the bushing was changed inconsiderably. Approximately 70-75 % percentages of the evacuated material composed the bushing shape, in TFD operations.

This article reports a novel and efficient method to synthesize graphene by thermal decomposition process. In this method, silicon carbide (SiC) thin films grown on Si(100) wafers with an AlN buffer layer were used as substrates. A CO₂ laser beam heating without vacuum or controlled atmosphere was applied for SiC thermal decomposition. The physical, chemical, morphological, and electrical properties of the laser-produced graphene were investigated for different laser energy densities. The results demonstrate that graphene was produced in form of small islands with quality, density and properties depending on the applied laser energy density. Furthermore, the produced graphene exhibits a sheet resistance characteristic similar to graphene grown on mono-crystalline SiC wafer, which indicates its potential for electronic device applications.

Conventional flame retardant (FR) application processes for textiles involve aqueous processing which is resource intensive in terms of energy and water usage. Recent research using sol-gel and layer-by-layer chemistries, while claimed to be based on more environmentally-sustainable chemistry, still require aqueous media with the continuing problem of water management and drying processes being required. This paper outlines the initial forensic work to characterise commercially produced viscose/flax, cellulosic furnishing fabrics which have had conferred upon them durable flame retardant (FR) treatments using a novel, patented atmospheric plasma/UV excimer laser facility for processing textiles with the formal name - Multiplexed Laser Surface Enhancement (MLSE) system. This system (MTIX Ltd., UK), is claimed to offer the means of directly bonding of flame retardant precursor species to the component fibres introduced either before plasma/UV exposure or into the plasma/UV reaction zone itself, thereby eliminating a number of wet processing cycles. Nine commercial fabrics, pre-impregnated with a semi-durable, proprietary FR finish and subjected to the MLSE process have been analysed for their flame retardant properties before and after a 40 °C 30 min water soak. For one fabric, the pre-impregnated fabric was subjected to a normal heat cure treatment which conferred the same level of durability as the plasma/UV-treated analogue. TGA and LOI were used to further characterise their burning behaviour and the effect of the treatment on surface fibre morphologies were assessed. Scanning electron microscopy indicated that negligible changes had occurred to surface topography of the viscose fibres occurred during plasma/UV excimer processing.

This paper reports the overall thermal performance of a cylindrical parabolic concentrating solar water heater (CPCSWH) with inserting nail type twisted tape (NTT) in the copper absorber tube for the nail twist pitch ratios 4.787, 6.914 and 9.042 respectively. The experiments are conducted for a constant volumetric water flow rate and during the time period 9:00 h to 15:00 h. The useful heat gain, hourly solar energy collected and hourly solar energy stored of this solar water heater are found higher for nail twist pitch ratio 4.787. The above said parameters are found to be a peak at noon and observed to follow the path of variation of solar intensity. At the starting of the experiment, the value of charging efficiency is observed to be maximum. Whereas the maximum value of instantaneous efficiency and overall thermal efficiency are observed at noon. The key finding is that the nail twist pitch ratio enhances the overall thermal performance of the CPCSWH.

During HVDC earth return operation systems, a high magnitude current will be injected into soil through earth electrode, the potential on the surface would change widely and produce unfavorable effects on the AC systems around. This paper presents an effective finite element method (FEM) coupling electric field with thermal field to evaluate the electrical field induced by the injected DC current. Firstly, owe to the characteristic of FEM, this method can consider arbitrary soil and earth electrode structure. Secondly, by setting the electrical and thermal parameters of soil as a function of temperature at the same time, the dynamic coupling process of electric field and thermal field is simulated accurately. Thirdly, to deal with the singular point in FEM subdivision and the huge computation in traditional three-dimensional FEM, the FEM coupling 2-D earth electrode with 3-D soil based on "shell" theory is introduced. Finally, based on the suggested method, the effect of abnormal resistance region (ARR) near DC earth electrode on electric field distribution is analyzed.

The thermal surface properties of graphenes and carbon materials are of crucial importance in chemistry of materials, chemical engineering, and many industrial processes. (1) Background: The determination of these surface properties is carried out using inverse gas chromatography at infinite dilution which leads to the retention volume of organic solvents adsorbed on solid surfaces. This experimental and fundamental parameter actually reflects the surface thermodynamic interactions between injected probes and solid substrates. (2) Methods: The London dispersion equation and the Hamieh thermal model were used to quantify the London dispersive and polar surface energy of graphenes and carbon fibers as well their Lewis acid-base constants by introducing the coupling amphoteric constant of materials. (3) Results: The London dispersive and polar acid-base surface energies, the free energy of adsorption, the polar enthalpy and entropy, and the Lewis acid-base constants of graphenes and carbon materials were determined. (4) Conclusions: it was showed that graphene exhibited the highest values of London dispersive surface energy, polar surface energy, and Lewis’s acid-base constants. These highest characteristics of graphene justify its great potentiality and uses in many industrial applications.

In the city of Valencia (Spain), existed from the Middle Ages until the mid-nineteenth century, a building that fulfilled a municipal strategic function: The “new flour-weighing house”. Its pur-pose was to distribute food to the population and collect the corresponding indirect municipal taxes. Today, the existence of this building is not remembered, neither by scientists nor by citizens, and its importance, location and appearance are unknown. The building investigated, behind which the medieval façade of the “flour-weighing house” is hidden, is the Colomina Palace. In the investigation, its growth phases have been detected and an idea of its structural organisation has been obtained. Research and investigation have been carried out by consulting historical, carto-graphic and archival material, together with advanced geomatics techniques, including close-range photogrammetry, terrestrial laser scanning and thermography. The fuse of colour and thermal imagery, altogether with point clouds and 3D models help to visualise and check the dif-ferent spatial transformations of the current “Colomina Palace”, adapting the sequence from me-dieval times into present.

Urban heat islands (UHI), exacerbated by climate change, significantly increase heat stress, particularly affecting vulnerable populations such as the elderly and children. This study evaluates the effectiveness of various urban heat mitigation technologies, including cooling fog systems, cool roofs (reflective paint), shading structures, and small water paths, in reducing temperatures and enhancing thermal comfort. Field tests were conducted from 2021 to 2023 across Gimhae-si, Yechun-gun, Geyang-gu, and Sangju-si, with support from the Korean Ministry of Environment. Results demonstrated that cooling fog systems provided immediate temperature reductions, lowering ambient temperatures by up to 3.1°C, while cool roofs reduced surface temperatures by 2-3°C. Shading structures reduced surface temperatures by up to 10°C, and small water paths cooled air temperatures by up to 1.5°C, also increasing humidity and improving thermal comfort. The findings suggest that a combination of these technologies can effectively mitigate urban heat stress, especially in areas with vulnerable populations.

The degradation of solar photovoltaic (PV) modules over time, aggravated by defects, significantly affects the performance of utility-scale PV parks. This study presents a quantitative assessment of the power loss from module defects, and evaluates the cost-effectiveness of replacing defective modules at various stages of degradation. A module test site was established in Norway with six different defects, and continuous thermographic monitoring, combined with light IV measurements and electroluminescence (EL) imaging, provides partial support for further calculations on the long-term effects of the defects. The cumulative module energy loss is calculated over a 25-year park lifespan under both Norwegian and Chilean environmental conditions, the latter representing higher solar irradiation levels. The energy gain from replacing the defective modules at various stages of degradation is compared to the costs of replacement, both for infant-life failures and mid-life failures. Minor infant-life defects of 1\% power loss are likely not beneficial to replace in low-irradiation regions like Norway. For Chilean conditions it can be cost-effective, but primarily if the module is replaced around mid park life, which gives a larger yield when replaced with a new module. For more severe defects of 10\% loss the replacement gain is above the replacement cost for high-irradiation locations, and replacing the 33\% power loss defect is cost-effective for both locations, even when discovered late in the park lifetime. Mid-life defects are primarily beneficial to replace in high-irradiation locations.

This research aims to develop top-emission OLEDs (Organic Light light-emitting diodes) that exhibit enhanced electro-optical properties regarding color purity, luminance, efficiency, stability, and longer lifetime. To achieve this aim, we have used silicon wafer substrates with a thickness of 675 m. Top-emission OLED fabrication on silicon wafer substrates requires careful material selection and layer configuration. This device structure is described as follows: Silicon/Al (100 nm)/ HATCN (10 nm)/ Dic-TRZ: Ir(mppy)3 (40 nm)/ TPBi (30 nm)/ LiF 1.2 nm / Al 19.9 nm. LiF/Al combination is used as the semi-transparent cathode. Research on top-emission OLEDs has demonstrated the importance of silicon wafer substrates in enhancing electro-optical properties. The optical properties of top-emission OLEDs are significantly influenced by factors such as the semitransparent cathode layer's thickness and the anode layer's surface roughness. Study findings encompass the impact of microcavity on TEOLEDs, dopant concentration on device performance, and device thermal conductivity and lifetime. To create a highly efficient top-emission OLED on a silicon substrate, we meticulously fine-tuned parameters such as the thickness of the cathode Al layer (19.9 nm), the organic layer thickness (HIL - HATCN 10 nm, HTL - NPB 30 nm, ETL - TPBi 30 nm, EML - DIC–TRZ: Ir(mppy)3 40 nm), and the dopant concentration. Electro-optical performance has been significantly improved through optimization, especially in devices with high dopant concentrations. The 38% dopant concentration experiments resulted in a peak current density of 201.97 mA/cm2, a luminance of 4776 cd/m2, and an efficiency of 2.36 cd/A at 9 V. In addition, the high dopant concentration has resulted in a narrow spectral range, indicating a strong microcavity effect. Additionally, Si-TEOLEDs were tested for lifetime under these specific conditions, exhibiting a half-life of 420 hours.

This work presents the results of optimizing the physicochemical properties of composite briquettes based on microsilica for metallurgical-grade silicon production. Microsilica, a waste product of silicon production, contains a sufficiently high amount of silicon dioxide (96-97%). This fact makes microsilica a promising composite material for metallurgical processing. However, its granulometric composition limits its direct use. The method of briquetting on an industrial briquetting press was used. The influence of the granulometric composition of the composite mixture on the heat tolerance and strength of the finished briquettes was studied. The methods of obtaining and testing the briquettes, their composition, and the briquetting and drying process are described. The obtained briquettes were tested for the smelting of metallurgical silicon. The silicon recovery rate in the metal with the standard charge was 71%, while the recovery rate with the briquetted monocharge was 85%. The results of silicon smelting from the briquettes demonstrated the high quality of the obtained metal, corresponding to the standards of metallurgical-grade silicon. The implementation of these technologies not only improves the quality of the final product but also addresses environmental issues related to the disposal of microsilica, reducing its accumulation and minimizing its impact on the environment.

Colloidal quantum dots (CQDs) are valuable for their potential applications in optoelectronic devices. However, they are susceptible to thermal degradation during processing and while in use. Mitigating thermally induced sintering, which leads to absorption spectrum broadening and undesirable changes to thin film electrical properties, is necessary for the reliable design and manufacture of CQD-based optoelectronics. Here, low temperature metal-oxide atomic layer deposition (ALD) was investigated as a method for mitigating sintering while preserving the optoelectronic properties of mercury telluride (HgTe) CQD films. ALD-coated films are subjected to temperatures up to 160oC for up to 5 hours and alumina (Al2O3) is found to be most effective at preserving the optical properties, demonstrating the feasibility of metal-oxide infilling to protect against sintering. HgTe CQD film electrical properties were investigated before and after alumina ALD in-filling, which was found to increase the p-type doping and hole mobility of the films. The magnitude of these effects depended on the conditions used to prepare the HgTe CQDs. With further investigation into the interaction effects of CQD and ALD process factors, these results may be used to guide the design of CQD-ALD materials for their practical integration into useful optoelectronic devices.

Black hole X-ray binary systems consist of a black hole accreting mass from its binary companion, forming an accretion disk. As a result, twin relativistic plasma ejections (jets) are launched towards opposite and perpendicular directions. Moreover, multiple broadband emission observations from X-ray binary systems range from radio to high-energy gamma-rays. The emission mechanisms exhibit thermal origins from the disk, stellar companion, and non-thermal jet-related components (i.e., synchrotron emission, inverse comptonization of less energetic photons, etc.). In many attempts at fitting the emitted spectra, a static black hole is often assumed regarding the accretion disk modeling, ignoring the Kerr metric properties that significantly impact the geometry around the usually rotating black hole. In this work, we study the possible implications of the spin inclusion in predictions of the X-ray binary spectrum. We mainly focus on the most significant aspect inserted by the Kerr geometry, the innermost stable circular orbit radius dictating the disk’s inner boundary. The outcome suggests a higher-peaked and hardened X-ray spectrum from the accretion disk and a substantial increase in the inverse compton component of disk-originated photons. Jet-photon absorption is also heavily affected at higher energy regimes dominated by hadron-induced emission mechanisms. Nevertheless, a complete investigation requires the full examination of the spin contribution and the resulting relativistic effects beyond the disk truncation.

Analyzing the impacts of urban landscape patterns on the thermal environment has become one of the key research areas in addressing urban heat islands (UHI) and improving the living environment. A case study was carried out in Fuzhou, Fujian Province of China, to quantify the spatial patterns of urban landscape and land surface temperature (LST) in different development areas. The contribution of the thermal environment and the factors influencing the heterogeneity of LST were analyzed and discussed. In this study, bi-temporal Landsat imagery was selected to calculate LST, percent impervious surface area (ISA), and fractional vegetation cover (FVC). The urban area was further divided into three concentric urban zones, ranging from the city center to the urban periphery, based on urban development densities. The spatial pattern of LST and its variance were analyzed and compared between different zones and different dates. The thermal environment contribution of different zones was also quantified to indicate the change in urban landscape pattern resulting from urban expansion in different zones. Furthermore, Geodetector was used to explore the single factors and interaction factors controlling the spatial patterns of LST in each zone. The results showed that (ⅰ) Urban expansion primarily increased in zone 2 and zone 3, and the areal proportion of high and sub-high LST areas increased from 56.11% and 21.08% to 62.03% and 32.49% in zone 2 and zone 3, respectively, from 2004 to 2021; (ⅱ) The heat effect contribution of zones 2 and 3 reached from 75.16% in 2004 to 89.40% in 2021, indicating that the increase of ISA with >LSTmean was more pronounced in zone 3 and zone 2 during the period; (ⅲ) The driving factors of LST spatial distribution were regionally different because of the different landscape patterns, and the explanatory power for the heterogeneity of LST in zone 1 was weaker than that in zone 2 and zone 3 in the study area; (ⅳ) The interaction of different factors had a higher explanatory power on the spatial distribution of LST than a single factor in each zone because the distributions of land cover types are heterogeneous in urban area. The results of the study can be used to improve urban planning for urban ecology and UHI mitigation.

In this research work the study of Buongiorno Model Darcy Forchheimer flow of Hybrid nanofluid flow on isothermal permeable stretch/shrink sheet with homogeneous and heterogeneous reaction is investigated. The effects of MHD, thermal radiation, viscous dissipation, Joule heating, and heat generation/absorption are taken into account. Hybrid nanofluids can act as a medium for heterogeneous-homogeneous reactions. The nanoparticles dispersed in the fluid can influence reaction kinetics and species transport, potentially, altering reaction rates and pathways. The applications of HNF in reactions, both homogeneous and heterogeneous, lie in leveraging their enhanced thermal properties, catalytic potential, and improved mixing capabilities to optimize reaction efficiency and control reaction conditions. Similarity transformation is used to convert a set of PDEs into a set of ODEs. HAM is used for the solution of the obtained ODEs system. In a heterogeneous reaction, the concentration gradient is amplified; in a homogeneous reaction, the impact is opposite. Moreover, at higher compositions of HNPs, the concentration and velocity rise while the temperature falls. Furthermore, as the values of homogeneous and heterogeneous reactions increase, the concentration falls. It is reliable with the idea that a greater reaction rate lowers the diffusion rate. Nevertheless, these parameters do not affect temperature or velocity.

Aquifer Thermal Energy Storage (ATES) systems are garnering attention as high-efficiency air conditioning technologies that contribute to the realization of a carbon-neutral society. This study focuses on an ATES system constructed in Japan, characterized by its complex geological conditions and thin aquifer layers. Through performance analysis using four years of operational data, we achieved a Coefficient of Performance (COP) of 5 on the building load side. This paper confirms the equivalence of the dimensionless production temperature and heat recovery rate, observing nearly identical changes in the dimensionless production temperature over four cycles (eight seasons). Furthermore, we propose an operational method for the following fiscal year that maintains the balance between accumulated storage quantity and pumping volume, based on predictions from this plant's operational pattern.

With the ever-growing emphasis on global decarbonization and rapid increases in the power density of electronics equipment in recent years, new methods and lightweight materials have been developed to manage heat load as well as interfacial stresses associated with Coefficient of Thermal Expansion (CTE) mismatch between components. The Al-Si system provides an attractive combination of CTE performance and high thermal conductivity whilst being a very lightweight option. Such materials are of interest to industries where thermal management is a key design criterion, such as aerospace, automotive, consumer electronics, defense, EV and space. This paper will describe the development and manufacture of a family of high-performance hypereutectic Al-Si alloys (AyontEX™) by a powder metallurgy method. These alloys are of particular interest for structural heat sink applications that require high reliability under thermal cycling (CTE of 17μm/(m·°C)) as well as reflective optics and instrument assemblies that require good thermal and mechanical stability (CTE of 13μm/(m·°C)). Critical performance relationships are presented, coupled with the microstructure, physical and mechanical properties of these Al-Si alloys.

There are several challenges on how to attain energy efficiency while maintaining balance among factors affecting energy consumption such as power rating and temperature setpoints of cooling units, room temperature and humidity, and indoor air quality (IAQ). A real-time energy and IAQ monitoring system were installed in an educational building to profile the operational power consumption of inverter-based air condition unit (ACU) installed in each room. Polynomial curve and neural fitting regression analysis were applied to the real-time power consumption, indoor temperature and humidity, and carbon dioxide (CO2) level data. The derived models were able to provide the stabilizing indoor thermal and air conditions of the room to reach steady state ACU power consumption. These collected data and calculated parameters can be used to define rules in automating control of cooling appliances for an efficient energy utilization. The regression approaches, using real-time data, have determined the influence of indoor heat conditions and carbon dioxide levels on ACU power consumption. These parameters were utilized to establish consistent values for temperature, humidity, and carbon dioxide levels under stable settings of inverter-based air conditioning units.

By this contribution we would like to briefly highlight the problems in conceiving the “Hydrogen Bond” (HB) as a real short-range, directional, electrostatic, attractive interaction and to reframe its nature through the non-approximated view of condensed matter offered by a Quantum Electro-Dynamic (QED) perspective. We focus our attention on water, as the paramount case to show the effectiveness of this 40-years’ old theoretical background, which depicts water as a two-fluid system (where one of the two phases is coherent). The HB emerge to be the result of the electromagnetic field gradient in the coherent phase of water, whose vacuum level is lower than the non-coherent (gas-like) fraction. Thus, the HB can be properly looked at, i.e. no more as a “dipolar force” among molecules, but as the phenomenological effect of their collective thermodynamic tendency to occupy a lower ground-state, compatibly with temperature and pressure. This perspective allows to account for many “anomalous” behaviours of water and to understand why the calculated energy associated to HB should change when considering two molecules (water-dimer), or the liquid state, or the several kinds of ice. The emergence of a condensed, liquid, phase at room temperature is indeed the consequence of the boson condensation as described in the framework of spontaneous symmetry breakings (SSB). The switch from a still semi-classical Quantum Mechanical (QM) in the 1st quantization to a Quantum Field Theory (QFT) view embedded in the 2nd quantization is advocated for a more realistic and authentic description of water, condensed matter and living systems.

Transport electrification is essential for reducing CO2 emissions, and technologies such as hybrid and range-extended electric vehicles will play a crucial transitional role. Such vehicles employ an internal combustion engine for on-board chemical energy conversion. The Wankel rotary engine should be an excellent candidate for this purpose, offering high power-to-weight ratio, simplicity, compactness, perfect balance, and low cost. Until recently, however, it has not been in production in the automotive market, due, in part, to relatively low combustion efficiency and high fuel consumption and unburnt hydrocarbon emissions, which can be traced to constraints on flame speed, an elongated combustion chamber, and relatively low compression ratios. This work uses large-eddy simulation to study the in-chamber flow in a peripherally ported 225cc Wankel rotary engine, providing insight into these limitations. Flow structures created during the intake phase play a key role in turbulence production but presence of the pinch point inherent to Wankel engine combustion chambers inhibits flame propagation. Two efficiency-enhancement technologies are introduced as disruptive solutions: (i) pre-chamber jet ignition and (ii) the two-stage rotary engine. These concepts overcome the traditional efficiency limitations and show that Wankel rotary engine design can be further enhanced for its role as a range extender in electrified vehicles.

This study explores the advanced integration of Bi2Te3-based thermoelectric systems in Ocean Thermal Energy Conversion (OTEC) to optimize performance. OTEC, a promising renewable energy source, needs help in efficiency maximization. We address this by implementing Bi2Te3 thermoelectric generators (TEGs), known for their high thermoelectric efficiency at low-temperature differences. Our research encompasses a comprehensive simulation and analysis of these TEGs in OTEC systems, examining material properties, system design, and environmental impact. We present a novel approach to integrating these TEGs, optimizing their arrangement, and interfacing with the OTEC cycle to enhance overall efficiency. The study also investigates the durability and cost-effectiveness of Bi2Te3 TEGs in marine environments. Results demonstrate a significant improvement in energy conversion efficiency, highlighting the potential of Bi2Te3 TEGs in sustainable ocean energy exploitation. This work advances material science in renewable energy, providing valuable insights into the practical application of thermoelectric materials in large-scale energy systems. It paves the way for future research on material optimization and system integration, essential for developing efficient and sustainable OTEC systems.

The MAGIC (Major Atmospheric Gamma-ray Imaging Cherenkov) Florian Goebel telescopes are a system of two Cherenkov telescopes located on the Canary island of La Palma (Spain), at the Roque de Los Muchachos Observatory, and operating in stereo mode since 2009. Their low energy threshold (reaching 15 GeV) allows the study of Active Galactic Nuclei (AGNs) in the very-high-energy gamma ray range with an impressive sensitivity up to the redshift limit of the existing IACT systems. MAGIC has collected many discoveries and comprehensive studies of different kinds of galaxies and their AGNs, also in a multi-wavelength context, expanding the knowledge of our Universe. Here we report the highlights which have been achieved by the MAGIC collaboration since the beginning of the operations.

This work explores five falling film evaporator (FFE) simulation approaches combined with energy consumption minimization strategies, namely Mechanical Vapor Recompression and Thermal Vapor Recompression (MVR and TVR respectively). Global system analysis and advanced dynamic optimization strategies are then investigated to minimize steam consumption, the cost of steam, the total annualized cost and maximizing product yield. The results indicate that a higher TVR discharge pressure, or MVR compression ratios, along with higher feed temperatures enhance evaporation with but increase operational costs. The most economic option includes three evaporator effects with TVR for achieving 50% product dry mass content. However, for a 35% dry mass content, MVR becomes cost-effective with an 11% reduction in unit electricity prices or a simultaneous 7% drop in electricity prices and a 5% increase in gas-based steam prices. Furthermore, switching from milk powder production to milk concentrates, an annual cost reduction ranging from 10.75 to 44% is achieved. Also, a forecasted 20% (or more) reduction of biomass-based steam cost can lead to lower annual expenditure comparing with the nominal NG-based steam Case. Regarding the total annualized cost, for a new plant design, optimization strategies lead to a 9 - 45% reduction in the total cost depending on the Case under consideration.

This study examines the impact of the impregnation of fireclay-based conventional (CC) and medium cement castables (MCC) with liquid sodium silicate glass under vacuum conditions. The goal is to assess how this treatment affects physical, mechanical properties, and durability (alkali and thermal shock resistance) of these castables used in biomass combustion boilers, where they are exposed to temperatures up to 1100°C. The research work employs standard test methods to evaluate physical and mechanical properties. Additionally, advanced techniques such as scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), and specific tests for alkali resistance and thermal shock resistance are used. The research findings suggest that impregnation with sodium silicate glass under vacuum significantly enhances the alkali resistance of both CC and MCC castables. This improvement is primarily due to the reduction in porosity and the increase in density. SEM images reveal that impregnated samples are coated with a glassy layer and the pores are partially filled with sodium silicate. Tests for alkali resistance demonstrate the formation of a protective glassy layer (with a thickness of 0.9-1.5 mm) on the castables surfaces, thereby reducing further penetration of alkali into deeper layers of the samples. However, it is important to mention that impregnated refractory castables have reduced resistance to thermal shock cycles.

The effect of neutron irradiation of Si-Ge/Si film structures obtained by gas-phase epitaxy on the processes of charge carrier generation and the magnitude of the dark short-circuit current and open-circuit voltage caused by it is studied, it is shown that their magnitude practically does not change with time. The results obtained indicate that all types of structural defects, both associated with dopant impurities and radiation exposure, contribute to the generation of charge carriers in heated silicon structures with the participation of deep energy levels, which indicates the applicability of neutron processing of silicon materials to create thermal energy converters, operating at high temperatures.

This research examines the fire resistance of geopolymer composites (GCs), formulated using alka-li-activated metakaolin and aluminum powder. The production method involves spray-coating carbon steel plates with fresh GCs, followed by a 28-day curing period at room temperature. Sub-sequently, fire performance and aging tests are conducted to evaluate fire resistance. The study investigates GC properties, including apparent density, bending strength, compression strength, thermal conductivity, porosity, and production cost. Morphological changes before and after fire and aging tests are analyzed using scanning electron microscopy (SEM). Results demonstrate GC foams' outstanding thermal insulation, providing up to 75 minutes of fire resistance with a 6 mm coating, reducing temperatures by 300 °C compared to uncoated steel. GCs exhibit a density of 670 kg/m³, thermal conductivity of 0.166 W/m·K, 68% porosity, and cost efficiency at 250 dollars per cubic meter. This study underscores the potential of foamed geopolymer coatings for effective and economical surface protection.

Energy demand and consumption in recent times have witnessed a rapid proliferation influenced by technological developments, increased population and economic growth. This has fuelled research trends in the domain of energy management employing tri-generation systems such as the combined cooling, heating and power (CCHP) systems. Furthermore, the incorporation of renewable energy, especially solar energy, to complement the thermal input by fossil fuels has facilitated the effectiveness and sustainability of CCHP systems. This study proposes a new approach to improve the overall efficiency of CCHP systems and compute the optimal design parameters in order to assist decision makers to identify the best geometrical configuration. A multi-objective optimization formulation of a solar-assisted CCHP system was adopted to maximize the net power, the exergy efficiency and minimize the CO2 emission using the greywolf optimization technique. In addition, the effects of the decision variables on the objective functions were analysed. The proposed optimization approach yielded 100 set of Pareto optimal solutions which would serve as options to the decision maker to make a selection in order to improve the performance of a solar-assisted CCHP system. This study demonstrates that the proposed approach is potentially suitable for the optimization of a solar-assisted CCHP system.