The social, environmental and scientific significance of the urban climate has shaped a research stream at Universitat Jaume I’s Climate Lab. Previous research has found higher temperature trends at urban observatories. This study examines in depth the features of the urban environment and the thermal behaviour of land use and land cover and the changes which have taken place. The CORINE Land Cover database was used to delimit the primary Land Use Land Cover (LULC) and its changes between 1990 and 2018. Once this had been established, land surface temperatures (LSTs) between 1985 and 2023 were retrieved from the Landsat database available on the Climate Engine website. Analysis of the primary land cover showed the greatest thermal increase in artificial surfaces, especially in industrial, commercial and transport units which are common on their outskirts. These areas also have the highest temperatures on a monthly basis with the biggest differences occurring in the summer. The results are less clear for urban fabrics and agricultural areas due to their diversity and complexity. The study concludes that urban growth and its commercial and industrial environment has an undeniable effect on the temperatures recorded by urban observatories and enables better decision-making when setting up weather stations for a more detailed time study of the urban heat island (UHI).

The paper examines the possibility of increasing the wear and corrosion resistance of a CP-Ti surface by duplex plasma electrolytic treatment (borocarburizing and polishing). The structure and composition of diffusion layers, their microhardness, surface morphology and roughness, wear resistance during dry friction and corrosion resistance in Ringer's solution were studied. The formation of a surface hardened layer up to 200 m thick with a microhardness of up to 950 HV, including carbides and a solid solution of boron and carbon, is shown. Subsequent polishing makes it possible to reduce surface roughness and remove weak areas of the porous oxide layer, which is formed during high-temperature oxidation in aqueous electrolyte vapor during borocarburizing. Changing the morphology and structural-phase composition of the CP-Ti surface helps reduce weight wear by 3 times (the mode of frictional interaction changes from microcutting to oxidative wear) and corrosion current density by 4 times after borocarburizing in a solution of boric acid, glycerin and ammonium chloride at 950 °C for 5 minutes and subsequent polishing in an ammonium fluoride solution at a voltage of 250 V for 3 minutes.

This study explores the effects of powder-to-liquid ratio on the performance characteristics of lost foam casting coatings. The investigation focuses on how variations in this ratio affect key properties including apparent viscosity, shear thinning behavior, coating weight, and surface morphology. Through a series of controlled experiments, coatings were prepared with different powder-to-liquid ratios and assessed for their physical and application properties. The results indicate that increasing the powder-to-liquid ratio raises the apparent viscosity and modifies shear thinning behavior. Notably, ratios exceeding 2.0 result in a sharp increase in viscosity that impedes coating application. The optimal powder-to-liquid ratio was determined to be between 2.0 and 2.2, where coatings demonstrated enhanced uniformity, improved particle distribution, and superior surface morphology. Coating weight increased up to a ratio of 2.2 but decreased beyond this threshold due to excessive viscosity. Both microscopic and macroscopic analyses confirmed that a ratio of 2.0 to 2.2 strikes the best balance for coating performance. These findings underscore the importance of precise powder-to-liquid ratio control to optimize the quality of lost foam casting coatings, offering valuable insights for refining coating formulations and application techniques in industrial contexts.

A method is proposed for analyzing the tremor of the earth's surface, measured by GPS, in order to highlight prognostic effects. The method is applied to analysis of daily time series of vertical displacements in Japan. The network of 1047 stations is divided into 15 clusters. The Huang Empirical Mode Decomposition (EMD) is applied to the time series of principal components from clusters with subsequent calculation of instantaneous amplitudes using the Hilbert transform. To ensure the stability of estimates of the waveforms of the EMD decomposition, 1000 independent additive realizations of white noise of limited amplitude were averaged before the Hilbert transform. Using a parametric model of the intensities of point processes, we analyze the connections between the instants of sequences of times of the largest local maxima of instantaneous amplitudes averaged over the number of clusters and the times of earthquakes in the vicinity of the Japan with minimum magnitude thresholds of 5.5 for the time interval 2012-2023. It is shown that part of the intensity of the sequence of times of seismic events, due to the influence of the times of the most expressive local extrema of instantaneous amplitudes, significantly exceeds the reverse influence.

The Ionian Sea is a crucial intersection for various water masses in the Mediterranean. Its hydrography and dynamics play a significant role in the seawater budgets and biogeochemistry of the neighboring sub-basins. Multiple theories have been formulated to gain a better understanding of the Ionian dynamics. These theories primarily attribute the variability of the near-surface Ionian circulation to internal processes. Here, we utilize horizontal currents and temperature-salinity profiles from the Copernicus reanalysis to examine the contribution of baroclinic modes to the variability of the basin horizontal circulation. Our findings demonstrate that, although the basin vertical structure is characterized by three layers, the primary patterns of the Ionian circulation can be attributed to the first baroclinic mode. This mode, along with the barotropic mode, accounts for over 85% of the overall variability in the Ionian circulation, suggesting that only one of the three interfaces separating the different water masses in the basin is dynamically active. We estimate the depth of this interface to be about 490 m. Additionally, our analysis shows that more than 90% of the kinetic energy over the water column is localized above this interface, indicating that the deep layer of the Ionian is dynamically nearly inert.

In this article, we describe a simple procedure for evaluating the sterility of nutrient media using a shear-horizontal surface acoustic wave (SH-SAW) biosensor. We used the SH-SAW biosensor platform to monitor the time-dependent phase responses of the material for the media that binds to a monolayer of 3-mercaptopropanyl-N-hydroxy succinimide on the biosensor surface. Increases in the phase shift less than 50% of the starting phase shift recorded 180 minutes after the sterilization indicate a successful sterility test of the media. Our devices were then applied to sterility testing using a viable Escherichia coli (E. coli) K-12 solution to confirm our hypothesis. Filtered LB Broth was the negative control, and a 24-hour culture of E. coli was the positive control. Before testing, the cell solution was pelleted, the media decanted, and then replaced with a 1x phosphate-buffered saline solution (1x PBS). Since we know that the N-hydroxysuccinimide residues will bind to amine groups, only in cases where microbial species are present will the surface binding increase greater than 50%. We confirmed our hypothesis using SH-SAW biosensors and overnight E. coli cultures. The sensitivity for our 250 MHz quartz SH-SAW sensors was calculated based on the response from the E. coli K-12 solution over the linear dynamic range, which appears to be 2x10^4 – 2x10^7 CFU per ml and has a sensitivity of S = 1.655x10^5 o m2 Kg-1. The limit of detection (LOD) for these sensors was calculated to be approximately 2x10^-9 grams (g), which is estimated to be approximately 2,000 Escherichia coli (E. coli) K-12 cells. However, the sensitivity and insertion loss remained approximately unchanged before and after coating the sensor with 3,3'-Dithiobis(succinimidyl) Propionate (DSP).

Maritime data not only identify financial resources that can significantly enhance the efficiency of shipping companies but also play a pivotal role in promoting eco-friendly and sustainable shipping practices. However, active corporate strategies are required to include maritime data essential for the commercial operation of autonomous ships in the form of corporate assets by transparent evaluating the data. The aim of this study is to review previous studies on da-ta-valuation models, identify a valuation model suitable for maritime business, consider the characteristics of maritime data. The analytic hierarchy process (AHP) method is used to derive priorities for valuing maritime data assets, with emphasis placed on the characteristics of mari-time data, followed by the character of the future-oriented maritime-data market and the da-ta-valuation model. The results obtained that the most important factors in selecting a maritime data-valuation model by analyzing the AHP method were identified as the characteristics of the maritime data(M1). The next most important factors analyzed were the features of the mari-time-data market(M2) and the features of the maritime data-valuation model(M3) in order. In addition, the characteristics of maritime data were preferentially considered among the main criteria, and the market approach (A2) was selected as the most optimal valuation model. The potential impact of this implementation could contribute to the establishment of an intelligent technology market by estimating the value of data and developing a platform for maritime data trading, allowing for more efficient data sharing and utilization by maritime autonomous sur-face ship(MASS).

In-depth insights into the profound impacts of climate change and human activities on water resources are garnered through the dynamic changes in surface water, a crucial aspect of effective water resource management and the preservation of aquatic ecosystems. This paper introduces an innovative approach employing the random forest algorithm for the systematic extraction and monitoring of surface water at large regional or national scales. This method integrates spectral bands, spectral indices, and digital elevation model data, offering a novel perspective on this critical task. A data filling model is proposed to mitigate the impact of missing data due to cloud cover. Leveraging the capabilities of the Google Earth Engine (GEE), detailed information on surface water dynamics during the rainy and dry seasons in the Yangtze River Basin (YRB) from 1991 to 2021 is extracted using Landsat time series imagery. The analysis encompasses spatial-temporal variation characteristics and trends, with a specific focus on the intricate interplay between the areal extent of surface water and hydro-meteorological factors in each sub-basin of the YRB. Importantly, this includes considerations of potential groundwater contributions to surface water. Key findings from our research include: (1) Achieving a remarkable overall accuracy of 0.96 ± 0.03 in obtaining reliable surface water datasets with the support of GEE. (2) Identifying significant trends, such as a noteworthy increase in rainy season surface water bodies (+248.0 km2·yr−1) and a concerning decrease in surface ice/snow cover during both rainy and dry seasons, with change rates of −39.7 km2·yr−1 and −651.3 km2·yr−1, respectively. (3) Uncovering the driving mechanisms behind these changes, revealing positive correlations between the areal extent of rainy season surface water bodies and precipitation, as well as negative correlations between surface ice/snow cover area and average surface skin temperature. It is crucial to note that these driving factors exhibit variation among secondary river systems, underscoring the complexity of surface water dynamics. Furthermore, comparative analyses with existing surface water products are conducted, contributing to a deeper understanding of the advantages and uncertainties inherent in our proposed extraction method. The proposed method for large-scale surface water extraction not only enhances the monitoring of spatio-temporal surface water dynamics in the YRB but also provides valuable insights for the sustainable utilization and protection of water resources, considering the potential role of groundwater in supplementing surface water.

The object of study is a transversely bent triangular plate made of orthotropic material fixed along the edges of the plate under the action of a uniformly distributed load. Fourth-order differential equilibrium equations with variable orthotropy parameters were used. The equations were approximated by finite differences for a grid of scalene triangles. This type of mesh accurately describes the boundary contour of the triangular-shaped plates. The boundary conditions for the mesh consider the orthotropy of the plate material. Seven standard finite-difference equations have been developed considering the boundary conditions along the three edges of the plate and the presence of three angles of an irregularly shaped triangle. A finite difference matrix is obtained. The matrix structure makes calculating a triangular plate at different base angles possible. The boundary conditions were varied in the form of rigid or hinged support of triangular plates. The calculation method considers the orthotropic parameters of the material in two mutually perpendicular planes. The adaptation of the numerical method to the calculation of orthotropic plates of arbitrary shape is described. Relationships are given for determining the rigidity characteristics of orthotropic materials. An algorithm for simple engineering calculation of triangular orthotropic plates is proposed, which makes it possible to perform accurate calculations in variant design.

In this work, nanocomposite photoelectrodes of the TiO2/ Au composition were manufactured, in which the size of plasmonic Au nanoparticles was varied, and the morphology of the TiO2 layer, depending on the thickness, changed from an island to a continuous layer. The influence of the morphology of plasmonic Au nanoparticles and the TiO2 layer on the optical and photoelectrochemical characteristics of hybrid photoelectrodes was studied. It has been shown that continuous coating of Au nanoparticles with a TiO2 layer (layer thickness 10 and 15 nm) leads to a decrease in the photoelectric response, and the decrease in photocurrent density and photoconversion efficiency decreases in proportion to the thickness of the TiO2 layer. The indicated drop in characteristics when plasmonic particles are located under the TiO2 layer is presumably associated with the scattering and recombination of charge carriers in the semiconductor layer. The best performance was shown by a system in which large Au nanoparticles (10 nm) are coated with a 5 nm thick layer of titanium dioxide; in this geometry, Au nanoparticles are decorated with TiO2 nanoparticles, as a result of which the photoelectrode-electrolyte interface has a more complex structure.

This paper investigates the reconfigurable intelligent surface (RIS)-aided uplink multicell massive multiple-input multiple-output (mMIMO) communication system with transceiver hardware impairments (THWIs), and the practical and feasible two-timescale scheme is used to design the phase shifts of RIS. We consider the Rician channel model and use maximal-ratio combining (MRC) technology to process the received signal at BS. The expression of the uplink achievable rate is derived and analyzed. Besides, genetic algorithm (GA) is used to optimize the phase shifts of RIS to maximize the data rate. Finally, the accuracy of the derived results is verified. The simulation results show that appropriately increasing the number of RIS’s reflecting elements can compensate for the performance loss caused by inter-cell interference and THWIs, and reduce the demand for the number of BS antennas, which can significantly reduce the hardware costs at the BS.

Radiative budget is one of the key factors influencing climate change. The aim of this study is to analyze radiative regime in Moscow using the MSU-RAD(BSRN) instrumentation complex and to estimate radiative effects of the main atmospheric factors during the 2021-2023 period. Due to variations in aerosol content, the loss of global shortwave irradiance (Q) varies from 37 to 186 W/m2 (or about 18-22%) at different solar elevations with a significant decrease in direct irradiance and increase in diffuse irradiance due to multiple scattering. In winter, we observed the increase in Q of about 45 W/m2 (or 9%) at h=30° due to high surface albedo, smaller aerosol and water vapor content. At the same time, net shortwave irradiance (Bsh) demonstrates a significant decrease due to prevailing effects of snow albedo. A nonlinear dependence of Q and Bsh cloud transmittance on relative sunshine duration (Sd) is observed. Mean changes in Q against the 1955-2020 period are characterized by negative anomalies (-22%) in winter and positive anomalies in summer (+3%) due to the changes in cloudiness, reflected in Sd variations. This is in line with global tendencies in long-term changes of shortwave irradiance in moderate climate in Europe during the last years.

Understanding surface water evaporation in tropical catchments is pivotal for effective water management, but limited research exists on stable isotopic (δ2H and δ18O) assessment of water evaporation losses. Our study bridges that gap, examining stable isotopes in meteoric water and surface waters across tropical regions, both humid and semi-arid. Using the Craig-Gordon model, we calibrated evaporation-to-inflow (E/I) ratios, identifying distinct E/I variations between seasons and regions. Notably, the semi-arid region consistently exhibited higher E/I ratios due to climatic characteristics. By integrating the Hamiltonian Monte Carlo and the No-U-Turn Sampler, we were able to quantify uncertainties in isotopic and meteorological parameters, resulting in E/I estimates within 68% and 95% confidence intervals. Our Bayesian model insights are critical for freshwater resource optimization and hydrological modeling in tropical regions.

Accurate climate data at fine spatial resolution are essential for scientific research and the development and planning of crucial social systems, such as energy and agriculture. Among them, sea surface temperature plays a critical role as the associated El Niño-Southern Oscillation (ENSO) is considered a significant signal of global interannual climate system. In this paper, we propose an implicit neural representation-based interpolation method with temporal information (T_INRI) to reconstruct climate data of high spatial resolution, with sea surface temperature as the research object. Traditional deep learning models for generating high-resolution climate data are only applicable to fixed resolution enhancement scales. In contrast, the proposed T_INRI method is not limited to the enhancement scale provided during the training process and its results indicate that it can enhance low-resolution input by arbitrary scale. Additionally, we discuss the impact of temporal information on the generation of high-resolution climate data, specifically, which month the low-resolution sea surface temperature data is from. Our experimental results indicate that T_INRI is advantageous over traditional interpolation methods under different enhancement scales, and the temporal information can improve T_INRI performance for a different calendar month. We also examined the potential capability of T_INRI in recovering missing grid value. These results demonstrate that the proposed T_INRI is a promising method for generating high-resolution climate data and has significant implications for climate research and related applications.

The time interval set approach depends on results for radiation propagation from star sources, where properties relate to sphere like propagation surfaces, finite for any realistic event and measurement. In contrast usually applied to stationary and parallel propagation is the traditional vector and one moment time coordinate kinematic approach from Newton’s laws. A time interval only description necessarily has to start from it's own definitions, and properties since time intervals have to be defined with time intervals. In this paper studied are time interval only set properties, commutation, addition and multiplication, and derivatives, and how to define these corresponding consistently with one moment time set properties. Time development and equilibrium within the time interval description depend on the well-known ‘mean velocity theorem’ and the time interval version of the Legendre transform. Radiation propagation ‘away from’ and gravitation ‘towards’ the star source are part of the one time interval description. In the second, discussion, part the time interval only set approach with only the fundamental properties is applied to radiation. Included is a derivation of star source radiation energy for both zero and non zero wave particle mass. The time interval set is not one of the usual sets encountered and the canonical property does not apply, the approach in this paper starts from commutation properties of one moment time coordinates and of time intervals and relates to Noether charges and structure constants. These are found to be equal to the radiation wave group-velocity, for photons the light velocity c, and, different from the usual derivative to one moment time, they equal specific arguments of the time interval only set derivative.

This research examines the fire resistance of geopolymer composites (GCs), formulated using alka-li-activated metakaolin and aluminum powder. The production method involves spray-coating carbon steel plates with fresh GCs, followed by a 28-day curing period at room temperature. Sub-sequently, fire performance and aging tests are conducted to evaluate fire resistance. The study investigates GC properties, including apparent density, bending strength, compression strength, thermal conductivity, porosity, and production cost. Morphological changes before and after fire and aging tests are analyzed using scanning electron microscopy (SEM). Results demonstrate GC foams' outstanding thermal insulation, providing up to 75 minutes of fire resistance with a 6 mm coating, reducing temperatures by 300 °C compared to uncoated steel. GCs exhibit a density of 670 kg/m³, thermal conductivity of 0.166 W/m·K, 68% porosity, and cost efficiency at 250 dollars per cubic meter. This study underscores the potential of foamed geopolymer coatings for effective and economical surface protection.

Bistatic scattering coefficient have important application of ocean active microwave remote sensing. In this paper, a general expression of the composite scattering coefficient for multiple dielectric targets of one-dimensional fractal sea surface is derived by MOM method. Secondly, the bistatic scattering coefficient is computed, there are two class missile targets and one class ship target of one-dimensional fractal sea surface, and the influence of the water dielectric constant, fractal dimension, wind speed, the target dielectric constant and spatial position is discussed, and the corresponding conclusions are given. The proposed algorithm is able to solve some composite scattering problems, such as “dielectric or conductive object + rough surface”, “dielectric or conductive floating object +rough ”and it has certain generalization and reference.

Keywords: Porcine reproductive and respiratory syndrome virus, baculovirus surface display vectors, neutralizing antibody, IFN-γ, IL-4.

Climate change is expected to result in rising temperatures, leading to increased occurrences of extreme weather events like heat waves and cold spells. Urban planning responses are crucial for improving the adaptive capacity of cities and communities in dealing with significant temperature variations across seasons. This study aims to investigate the relationship between urban temperature fluctuations and urban morphology throughout the four seasons. Through quadrant and statistical analyses, the study identifies built-environment factors that contribute to moderate seasonal land surface temperatures (LST). The research focuses on Seoul, South Korea as a case study and calculates seasonal LST values at both the grid level (100m×100m) and street-block level, incorporating factors such as vegetation density, land use patterns, albedo, two- and three-dimensional building forms, and gravity indices for natural reserves. The quadrant analysis reveals spatial segregation between areas demonstrating high LST adaptability (cooler summers and warmer winters) and those displaying LST vulnerability (hotter summers and colder winters), with significant differences in vegetation and building forms. The spatial regression analysis demonstrates that higher vegetation density and proximity to water bodies play key roles in moderating LST, leading to cooler summers and warmer winters. Building characteristics have an invariant impact on LST across all seasons, where horizontal expansion contributes to higher LST, while vertical expansion reduces LST. These findings are consistent for both grid- and block-level analyses. The study emphasizes the flexible role of the natural environment in moderating temperatures.

A two-layer Fe-Cr-Al-Zr surface alloy was synthesized on a zirconium substrate by magnetron sputtering and subsequent low-energy high-current electron-beam (LEHCEB) processing. Thicknesses of the top Fe69Cr20Al11 (at.%) relatively large-grained (~1 µm) and transition Fe-Zr Cr-Al amorphous layers were about 0.7 and 0.6 µm, respectively. In turn, the amorphous layer consisted of two Fe64–54Zr8–22Cr21–17Al8–7 and Fe40–16Zr42–78Cr12–4Al6–2 (at.%) sublayers, differing in both zirconium and iron concentrations in wide ranges, which were separated by another nanocrystalline interlayer. The Fe-Cr-Al-Zr surface alloy serve as a diffusion barrier, preventing interaction of the zirconium substrate with oxygen from an environment. It was thermally stable up to ≈1173 K.

This study investigates the transition from surface to underground mining at the Sepon Gold mine. The stability of surface slopes is assessed prior to commencing underground operations. Stope mining is adopted based on ore body characteristics and geological features. Finite element numerical analysis, employing the Generalized Hoek-Brown criterion, evaluates slope stability for surface slopes and opening stopes. The pit design comprises a 70° slope angle, 20 m height, and 10-15 m safety berm, meeting stability requirements with a factor of safety of 2.46. Underground mining design includes a 62° ore body dip, 50 m thick crown pillar to prevent surface subsidence, and 5 m wide, 5 m high stopes. Sill pillars are left for support after each level excavation. Rock bolts are employed in specific stope areas where is necessary, with continuous monitoring for surface deformation. The study analyzes the influence of stope sizes on pit wall and pit bottom stability, identifying slope failures near the hanging wall close to the pit bottom during underground mining. A slight increase in the displacement zone is observed on the upper crest of the top footwall. Overall, the findings demonstrate successful stability in the transition from surface to underground mining at Sepon Gold mine.

Large-area nanostructuring of glasses using intense laser beam remains a difficult task due to the extreme non-linear absorption of the laser energy by the material. Precise optimization of the process parameters is essential for fabricating nanostructures with large area coverage. In this study, we report the findings on creating high spatial frequency LIPSS (HSFL) on borosilicate glass through direct laser writing, using a femtosecond laser with a wavelength λ = 800 nm, pulse duration τ = 35 fs, and repetition frequency frep = 1 kHz. The orientation of the HSFL was found to be parallel to the electric field vector. We measured the single pulse ablation threshold (Fth=3.87±0.26 J/cm2) and incubation factor (S=0.68±0.03) of Borosilicate glasses for precise control for large area surface structuring. Single-spot experiments indicate that uniform LIPSS formation is limited by melt formation inside the irradiated area for higher fluence and a larger number of irradiated laser pulses. The orientation of the scan axis with the laser beam polarization is found to be significantly influencing the uniformity of the large area processing. We found that the orientation of the scan axis with the laser beam polarization significantly affects the uniformity of large-area processing, with redeposition and melt formation being higher when the scan axis is perpendicular to the laser beam polarization. Large-area processing of the borosilicate glass surface is done by line-by-line scanning over the surface with a scan orientation parallel to the laser beam polarization. The optical characterization reveals that the transmittance and reflectance of the borosilicate glass decreased significantly after processing. Also, the wettability of the surface has been changed from hydrophilic to super hydrophilic after processing. These chemical contamination-free and uniformly distributed structures have potential applications in optics, microfluidics, photovoltaics, and biomaterials.

The discovered light modulation capabilities of diatom silicious valves make them an excellent toolkit for photonic devices and applications. In this work, a reproducible surface-enhanced Raman-scattering (SERS) enhancement was achieved with hybrid substrates employing diatom silica valves coated with an ultrathin uniform gold film. Three structurally different hybrid substrates, based on the valves of three dissimilar diatom species, have been compared to elucidate the structural contribution to SERS enhancement. The comparative analysis of obtained results showed that substrates containing cylindrical Aulacoseira sp. valves achieved the highest enhancement up to 14-fold. Numerical analysis based on the frequency domain finite element method was carried out to supplement the experimental results. Our results demonstrate that diatom valves of different shapes can enhance the SERS signal, offering a toolbox for SERS-based sensors, where the magnitude of the enhancement depends on valve geometry and ultrastructure.

In this work, we have proposed two new methods for the synthesis of [TcO2L4]+ (where L = im-idazole (Im), methylimidazole (MeIm)) complexes using thiourea (Tu) and Sn(II) as reducing agents. The main and by-products of the reactions were determined, and possible reaction mechanisms were proposed. We have shown that the reduction of Tc(VII) with thiourea is ac-companied by the formation of the Tc(III) intermediate and further oxidation to Tc(V). The reac-tion conditions changing can lead to the formation of Tc(VII) and Tc(IV) salts. Seven new crystal structures are described in this work: Tc(V) complexes, salts with Tc(VII) and Tc(IV) anions. For halide salts of Tu the cell parameters were determined. In all obtained compounds, except for [TcO2(MeIm)4]TcO4, there are π-stacking interactions between aromatic rings. An increase in the anion size lead to weaken intermolecular interactions. Halogen bonds and anion-π interactions have also been found in hexahalide-containing compounds. The Hirshfeld surface analysis showed that the main contribution to the crystal packing is made by van der Waals interactions of the H···H type (42.5–55.1%), H···C/C ···H (17.7–21.3%) and hydrogen bonds, which contribute 15.7–25.3% in total.

This article addresses the problem of formation control of a quadrotor and one (or more) marine vehicles operating at the surface of the water with the end goal of encircling the boundary of a chemical spill, enabling such vehicles to carry and release chemical dispersants used during ocean cleanup missions to break-up oil molecules. Firstly, the mathematical models of the Medusa class of marine robots and quadrotor aircrafts are introduced, followed by the design of single vehicle motion controllers that allow these vehicles to follow a parameterized path individually using Lyapunov based techniques. At a second stage, a distributed controller using event triggered communications is introduced, enabling the vehicles to perform cooperative path following missions according to a pre-defined geometric formation. In the next step, a real time path planning algorithm is developed that makes use of a camera sensor, installed on-board the quadrotor. This sensor enables the detection in the image of which pixels encode parts of a chemical spill boundary and use them to generate and update in real time a set of smooth B-spline based paths for all the vehicles to follow cooperatively. The performance of the complete system is evaluated by resorting to 3-D simulation software, making it possible to simulate visually a chemical spill. Results from real water trials are also provided for parts of the system, where two Medusa vehicles are required to perform a static lawn-mowing path following mission cooperatively at the surface of the water.

Every protein consists of a linear sequence over an alphabet of $20$ letters/amino acids. The sequence unfolds in the $3$-dimensional space through secondary (local foldings), tertiary (bonds) and quaternary (disjoint multiple) structures. The mere existence of the genetic code for the $20$ letters of the linear chain could be predicted with the (informationally complete) irreducible characters of the finite group $G_n:=\mathbb{Z}_n \rtimes 2O$ (with $n=5$ or $7$ and $2O$ the binary octahedral group) in our previous two papers. It turns out that some quaternary structures of protein complexes display $n$-fold symmetries. We propose an approach of secondary structures based on free group theory. Our results are compared to other approaches of predicting secondary structures of proteins in terms of $\alpha$ helices, $\beta$ sheets and coils, or more refined techniques. It is shown that the secondary structure of proteins shows similarities to the structure of some hyperbolic $3$-manifolds. The hyperbolic $3$-manifold of smallest volume --Gieseking manifold--, some other $3$ manifolds and the oriented hypercartographic group are singled out as tentative models of such secondary structures. For the quaternary structure, there are links to the Kummer surface.

Esophageal adenocarcinoma (EAC) detection relies on endoscopy-biopsy diagnosis, with routine endoscopic surveillance recommended for Barrett’s esophagus (BE) patients. Here, we examine the utility of blood biomarkers in patient risk stratification by translating the EAC blood biomarker Jacalin lectin binding complement C9 (JAC-C9) into a novel microfluidic immunoassay, the EndoScreen Chip. Cohort evaluation (n=46) showed elevated serum total C9 and JAC-C9 in EAC. Logistic regression modeling demonstrated that addition of C9 and JAC-C9 to patient risk factors (age, body mass index and heartburn/reflux history) improved EAC prediction from AUROC of 0.838 to 0.931. Serum JAC-C9 strongly predicted EAC (vs BE OR= 4.6, 95% CI: 1.6-15.6, p = 0.014; vs Healthy OR=4.1, 95% CI:1.2-13.7, p = 0.024) while total C9 was moderately predictive for BE (vs EAC OR=1.4; 95% CI: 1.0-1.8, p = 0.032; vs Healthy OR=0.8; 95% CI: 0.6-1.0, p = 0.039). This translational study demonstrates the potential utility of blood biomarkers in improving triaging for diagnostic endoscopy.

The aim of this articles is to investigate the entropy optimization in unsteady MHD flow Darcy-Forchheimer nanofluids towards a stretchable sheet. The surface we tend to think about is porous and stretchy under acceleration. Flow occurs due to the stretching of the surface. Four distinct types of aqueous nanostructures are taken in this examination where copper oxide ( ), copper ( ), titanium dioxide ( ) and aluminum oxide ( ) are the nanoparticles. Irreversibility analysis are discussed through second law of thermodynamics. The expression of energy is mathematically designed and discussed according to heat generation / absorption, dissipation, thermal radiation, and joule heating. The nonlinear PDE (partial differential conditions) is first changed to ODE (normal differential conditions) through appropriate similarity variables. Here we used the numerically embedded solution technique to develop a numerical result for the obtained nonlinear flow expression. Influence of various flow parameter velocity temperature distribution and entropy generation are discussed. Reduction occurs in velocity profile for larger porosity and magnetic parameters. An enhancement in entropy generation and temperature distribution is seen for Brinkman number. An opposite effect is noticed in velocity and temperature through solid volume friction.

C-C Chemokine receptor type 5 (CCR5) is expressed on the CD4 T cell surface where CXCR4 and CCR5 expressions are controlled differently during the activation of T cells and with the binding of interleukin type-2 (IL-2). IL-2 can upregulate CCR1 and CCR2 in CD45R01 T cells and increase the T lymphocyte chemotaxis toward CC-chemokines. CD4+ T cells are either apart of the T helper 1 or Th1 lymphocytes that release interferon gamma (IFNγ) and lymphotoxin that provide cellular immunity to internal pathogens and T helper cells type 2 (Th2), which secrete interleukins 4 and 5 (IL-4 and IL-5). IL-4 and IL-5 cause an allergic and humoral immune response to parasites. Th2 lymphocytes use CCR3 chemokine receptors. CCR5 and CXCR3 chemokine receptors are specific for CD4+ Th1 and Th2 lymphocytes. CCR5Δ32 is a 32-base-pair deletion of the CCR5 gene. CCR5 is a co-receptor for the entrance of the human immunodeficiency virus-1 (HIV-1). CCR5Δ32 creates a malfunction of the CCR5 protein that can prevent HIV-1 infection. However, the CCR5Δ32 32-base-pair deletion is not prevalent and predominant in many populations worldwide and there also exist more genetic variations of CCR5 known as CCR5-SNPs. An alternative polymorphism was identified based on the CCR5 gene that was identified as a A to G (A/G) point mutation. This point mutation is located at the 59029 locus on the promoter that lowers the expression rate of CCR5. Gurdol et al. found activity at the promoter of CCR5/590029G was 45% lesser than the CCR5/59029A. The genetic variations of CCR5 SNPs also include: 2459G>SNP of CCR5, C101X, CCR5 gene position at -2273, and the A to G SNP mutation found in two South African blacks. Therefore, more studies are needed to find more and varied chemokine polymorphisms that are present in many diverse populations in the world. The aim of this literature review is to describe the immense impact of CCR5 SNP mutations on viral infection susceptibility, on the pathogenesis of chronic conditions, to endorse the increased discovery of more novel CCR5 SNPs, and to show the significant potential of anti-CCR5 therapies to treat multiple diseased conditions.

The surface enhanced fluorescence（SEF）detection bases by plasmonic nanopillars array with nanoparticles has opened up a new gate in the application of biological imaging and sensing. The fluorescence enhancement of the probe molecule depends on its position in equilibrium, which is close to the hot spot leading to the electromagnetic field enhancement, but not too close to the metal surface resulting in quenching. Here, a large scale SiO₂-Ag-cicada wing SEF substrate was fabricated by magnetron sputtering with correction enhancement factor of 797.6. Thereinto the cicada wing provides the skeleton of the nanopillars array structure, the deposited Ag constructs two kinds of hot spots, and SiO₂ forms a separation layer to prevent quenching. Moreover, the substrate exhibited good reproducibility, high sensitivity with low limits of detection (LOD) and high stability for oxidation resistance. We propose that SEF substrate with modification of SiO₂ can not only improve the enhancement performance, but also expanding its application in the biological investigations.

In this study, the efficiency of an anaerobic treatment system for wastewater from a South African poultry slaughterhouse was evaluated using a lab-scale static granular bed reactor (SGBR). The down-flow SGBR (2 L) was operated continuously for 138 days under mesophilic conditions (35-37 ˚C), at hydraulic retention times (HRTs) ranging from 24 to 96 h and average organic loading rates (OLRs) of 0.78 to 5.74 g COD/L.day. The SGBR achieved an average chemical oxygen demand (COD) removal efficiency of 80% and the maximum COD removal achieved was 95%, at an HRT of 24 h and average OLR of 5.74 g COD/L.day. The optimization of the SGBR, with regard to a suitable HRT and OLR, was determined using response surface methodology (RSM). The optimal SGBR performance with regard to the maximum COD removal efficiency was predicted for an OLR of 12.49 g COD/L.day and a HRT of 24 h, resulting in a 95.5% COD removal efficiency. The model R2 of 0.9638 indicated that the model is a good fit and is suitable to predict the COD removal efficiency for the SGBR.

Ferulic acid esters have been suggested as a group of natural chemicals with sunscreen function. The study aimed to utilize an environment-friendly enzymatic method to produce octyl ferulate by esterification of ferulic acid with octanol. The Box-Behnken design with response surface methodology (RSM) was adopted to evaluate the effects of synthesis variables, including reaction temperature (70–90 °C), enzyme amount (1000–2000 PLU) and stir speed (50–150 rpm), on the molar conversion of octyl ferulate. According to the joint test, both the reaction temperature and enzyme amount had great impacts on the molar conversion. RSM-developed second-order polynomial equation further showed great ability on data-fitting. Based on ridge max analysis, the optimum parameters for the biocatalyzed reaction were: 72 h reaction time, 92.2 °C reaction temperature, 1831 PLU enzyme amount and 92.4 rpm stir speed, respectively. Finally, the molar conversion of octyl ferulate under optimum condition was verified to be 93.2 ± 1.5%. In conclusion, high yield of octyl ferulate synthesized by commercial immobilized lipase under elevated temperature conditions has been suggested, which our findings could broaden the utilization of the lipase and provide a biocatalytic approach, instead of the chemical method, for ferulic acid ester synthesis.

Surface area and pore size distribution of Eucalyptus samples pretreated by different methods were determined by the Brunauer-Emmett-Teller (BET) technique. Three methods were applied to prepare cellulosic biomass samples for BET measurements: air, freeze, and critical point drying (CPD). Air and freeze drying caused severe collapse of biomass pore structures, but CPD effectively preserved biomass morphology. Surface area of CPD prepared Eucalyptus samples was determined to be 58–161 m2/g, whereas air and freeze dried samples were 0.5–1.3 and 1.0–2.4 m2/g, respectively. Average pore diameter of CPD prepared Eucalyptus samples were 61–70Å. CPD preserved Eucalyptus sample morphology by replacing water with a non-polar solvent, CO2 fluid, which prevented hydrogen bond reformation in the cellulose.

Polylactic Acid (PLA) is an organic polymer commonly used in fused deposition (FDM) printing and biomedical scaffolding that is biocompatible and immunologically inert. However, variations in source material quality and chemistry make it necessary to characterize the filament and determine potential changes in chemistry occurring as a result of the FDM process. We used several spectroscopic techniques, including laser confocal microscopy, Fourier-Transform Infrared (FTIR) spectroscopy and photoacousitc FTIR spectroscopy, Raman spectroscopy, and X-ray photoelectron Spectroscopy (XPS) in order to characterize both the bulk and surface chemistry of the source material and printed samples. Scanning Electron Microscopy (SEM) and Differential Scanning Calorimetry (DSC) were used to characterize morphology, crystallinity, and the glass transition temperature following printing. Analysis revealed calcium carbonate-based additives which were reacted with organic ligands and potentially trace metal impurities, both before and following printing. These additives became concentrated in voids in the printed structure. This finding is important for biomedical applications as carbonate will impact subsequent cell growth on printed tissue scaffolds. Results of chemical analysis also provided evidence of the hygroscopic nature of the source material and oxidation of the printed surface, and SEM imaging revealed micro and sub-micron scale roughness that will also impact potential applications.

This study was designed for the first time to improve phenolic yield and antioxidant activity of ultrasonic-assisted extraction from Acer truncatum leaves (ATL) using response surface methodology, and phenolic composition in ATL extracted under the optimized condition were characterized by UPLC-QTOF-MS/MS. Solvent and extraction time were selected based on preliminary experiments, and a four-factors-three-levels central composite design was conducted to optimize solvent concentration (X₁), material-to-liquid ratio (X₂), ultrasonic temperature (X₃) and power (X₄) for an optimal total phenol yield (Y₁) and DPPH• antioxidant activity (Y₂). The results showed that the optimal combination was ethanol: water (v:v) 66.21%, material-to-liquid ratio 1:15.31 g/mL, ultrasonic temperature 60 °C, power 267.30 W, and time 30 min with three extractions, giving a maximal total phenol yield of 7593.62 mg gallic acid equivalent /100 g d.w. and a maximal DPPH• antioxidant activity of 74241.61 μmol Trolox equivalent/100 g d.w.. Furthermore, 22 phenolics were first identified in ATL extract obtained under the optimized conditions, indicating that gallates, gallotannins, quercetin, myricetin and chlorogenic acid derivatives were the main phenolic composition in ATL. What’s more, a gallotannins pathway existing in ATL from gallic acid to penta-O-galloyl-glucoside was interpreted. All these results provided practical information aiming at full utilization of phenolics in ATL, together with fundamental knowledge for further research.

The incremental sheet forming is born as an excellent alternative to other material forming pro-cedures to deform incrementally flat metal sheets into the preferred complex three-dimensional profile. The main characteristics of this process are its versatility and cost-effectiveness; in addition, it allows for reaching greater formability, compared to conventional sheet forming processes. Re-cently, its use has been extended to polymers and composites. The following review aims to present the current state of the art of the incremental sheet forming of polycarbonate, an outstanding en-gineering plastic, starting from the first studies on the feasibility of this process applied to polymers. Attention is given to the advantages, drawbacks and main applications of the incrementally formed polycarbonate sheets, as well as the influence of the process parameters and the toolpath strategies on features like formability, forming forces, deformation and failure mechanisms, geometric accu-racy, surface quality, etc. Moreover, new hybrid forming methods for process optimization are presented. Finally, a discussion is provided on the technical challenges and research directions for incremental sheet forming of polycarbonate, and more generally thermoplastics, in the future. Therefore, this review aims to offer an extensive overview of the incremental forming of polycar-bonate sheets, useful to academic and industrial researchers who work on this topic.

The paper deals with two new properties of the linear time-optimal control problems with real non-positive eigenvalues of the system. They are the foundation of a new method of synthesizing the time-optimal control without the need to describe the switching hyper-surfaces. The so called “axes initialization” and the synthesis technique are illustrated on the already classical example of the time-optimal control of a double integrator.

Plastic pollution is a pressing environmental challenge, necessitating the development of biodegradable alternatives like polyhydroxybutyrate (PHB). This study focuses on optimizing PHB production by Neobacillus niacinii GS1, a bacterium isolated from a municipal dumping site. By utilizing agricultural residues such as corn flour, wheat bran, and peptone as substrates, we aimed to establish an eco-friendly method for biopolymer production, contributing to sustainable waste management and bioplastic innovation. The bacterium was identified using morphological, biochemical, and molecular techniques. The optimization process involved adjusting variables such as inoculum age, inoculum size, incubation time, agitation rate, incubation temperature, pH of the medium, carbon sources and nitrogen sources. Response surface methodology (RSM) was employed to identify optimal conditions, with the highest PHB yield of 61.1% achieved under specific conditions: 37°C, pH 7, and an agitation rate of 150 rpm. These findings underscore the potential of Neobacillus niacinii GS1 in converting agro-industrial residues into valuable biopolymers, promoting sustainable bioplastic production, and advancing waste valorization efforts through the use of eco-friendly materials.

Despite advances in conservation-restoration treatments, most surface cleaning tests are subjectively evaluated. Scores according to qualitative criteria are employed to assess results, but these can vary by user and context. This paper presents a range of cleaning efficacy and homogeneity evaluation metrics for appraising cleaning trials, which minimise user bias by measuring quantifiable changes in the appearance and characteristic spectral properties of surfaces. The metrics are based on various imaging techniques (optical imaging by photography using visible light (VIS); spectral imaging in the visible-to-near-infrared (VNIR) and shortwave infrared (SWIR) ranges; chemical imaging by Fourier transform infrared (FTIR) spectral mapping in the mid-infrared (MIR) range; and scanning electron microscopy coupled with energy dispersive X-ray spectroscopy (SEM-EDX) element mapping). They are complemented by appearance measurements (glossimetry and colorimetry). As a case study showcasing the low-cost to high-end metrics, agar gel spray cleaning tests on exposed ground and unvarnished oil paint mock-ups are reported. The evaluation metrics indicated that spraying agar (prepared with citric acid in ammonium hydroxide) at a surface-tailored pH was a safe candidate for efficacious and homogenous soiling removal on water-sensitive oil paint and protein-bound ground. Further research is required to identify a gel-based cleaning system for oil-bound grounds.

A novel five-surface phosphor-in-glass (FS-PiG) for high illumination and excellent color uniformity in larger-scale LEDs for sensor light source application is demonstrated. YAG phosphor (Y3Al5O12:Ce3+) was uniformly mixed with ceramic and sintered at 680°C to form a phosphor wafer. A sophisticated laser engraving was employed on the phosphor wafer to form a saddle-shaped large-scale FS-PiG LEDs. The performance of the FS-PiG LEDs exhibited the illumination of 401lm, average color temperature (CCT) of 5488K±110K, and color coordinates (CIE) of (0.3179±0.003, 0.3352±0.003). In contrast to convention single-surface phosphor-in-glass (SS-PiG) LEDs, the performance exhibited the illumination of 380lm, average CCT of 5830K±758K, and CIE of (0.3083±0.07, 0.3172±0.07). These indicated that the performance of the FS-PiG LEDs was higher than the SS-PiG LEDs for illumination, CCT, and CIE of 1.7, 7, and 23 times, respectively. Furthermore, the FS-PiG LEDs demonstrate lower lumen loss of 2% and less chromaticity shift of 5.4x10-3 under accelerated aging at 350°C for 1008 hours, owing to the high ceramic melting temperature of up to 510°C. In this study, the proposed FS-PiG larger-scale LEDs having excellent optical performance and high reliability may be the promising candidates to replace the convention phosphor-in-organic silicone material used in high-power LEDs for the next generation of sensor light sources, display, and headlight applications.

Under the action of cement hydration heat, construction environment, thermal insulation measures, and pipe cooling system, the mass concrete pile cap produces a complex temperature field inside the structure, which makes it difficult to control the internal surface temperature difference, the maximum adiabatic temperature rise and the surface temperature of the structure. In this paper, the mass concrete pile cap of a super large bridge (the length, width, and height are 26.40m，20.90m, and 5.00m, respectively, and the central pier pile cap is constructed with concrete with a strength of C40) is taken as the research support project. The controlling factors affecting the temperature field of the mass concrete pile cap are found by comparing the temperature monitoring of the pile cap with the calculated value of finite element software simulation analysis. Through the finite element software Midas Civil and Midas FEA, the control factors affecting the temperature field of the main pier cap (concrete mold temperature, concrete surface convection coefficient, ambient temperature, and pipe cooling system parameters, etc.) are numerically analyzed, and the influence law and influence degree of the control factors are found out.

This study investigated how the type and homogenisation parameters of the feed mixture affect the efficiency of the encapsulation process and the microcapsule properties of phenol-rich grape pomace extract (GPE) during the spray drying process with goat whey protein (GW) as wall material. GPE was obtained by solid-liquid extraction of grapes with 50% ethanol. Effects of ultrasonic homogenisation parameters (UB): temperature: 30-50 °C; time: 5-30 min; stabilisation time after homogenisation: 15-45 min, and homogenisation parameters on a magnetic stirrer (MS): temperature (25-50 °C), time (10-60 min) and homogenisation speed (600-1200 rpm) were tested using response surface methodology (RSM) and Box-Behnken design. After selecting the optimal homogenisation conditions, the spray drying process parameters were optimised in the same way, namely: inlet air temperature (160-190 °C), GW fraction (0.5-3.5) and feed flow (6-10 mL/ min). The results showed that GW has a high potential as a wall material in the spray drying process, especially for the purpose of protecting polyphenolic compounds from GPE.

The goal of the project was to understand how topography/bathymetry is imported and used in GeoFlood with an aim towards improving efficiency and computational cost of bathymetry handling in GeoFlood.GeoFlood is a software to simulate overland flooding basing on shallow water equations.Numerical methods and programming were used for this study.The GeoFlood was ran on a given data set (Malpasset data) and it was found out that indeed topography handling during simulations has to be improved to minimise the computational time and also improve the efficiency.Through this research, we also looked at the the shallow water equations, and the numerical techniques used to solve the equations

Low-frequency electromagnetic induction (EMI) is a non-invasive geophysical method that is based on the induction of electromagnetic (EM) waves into the subsurface to quantify changes in electrical conductivity. In this study we present an open (design details and software are accessible) and modular system for the collection of EMI data. The instrument proposed allows to adjust the separations between the transmitter and up to four receiving antennas as well as the acquisition frequency (in the range between 3 and 50 kHz) to permit measurements with variable depth of investigation. The sensor provides access to raw data and the software described in this study allows control of the signal processing chain. The design specifications permit apparent conductivity measurements in the range of between 1 mS/m and 1000 mS/m, with a resolution of 1.0 mS/m and with a sampling rate of up to 10 samples per second. The sensor allows for a synchronous acquisition of a time stamp and a location stamp for each data sample. The sensor has a mass of less than 5 kg, is portable and suitable for 1-person operation, provides 4 hours of operation time on one battery charge, and provides sufficient rigidity for practical field operations.

The COVID-19 virus was first detected in Wuhan, China and its genesis was traced to infected bats, passed through an intermediate host to humans. COVID-19 or “Coronavirus” reached approximately 4 million confirmed cases in the United States by July 2020. The spread of this virus has affected both social and economic affairs on a global scale with more than 15 million confirmed cases worldwide in July 2020. The pandemic has proven a global public health and socio-economic crisis. In addition, the shelter-in-place orders provide an unprecedented opportunity for examining the resulting reduction in greenhouse gases and aerosols on the atmosphere. The Sentinel-5P satellite has shown distinct changes in atmospheric compounds over the COVID-19 epicenter in Wuhan. After Texas, U.S.A. established similar shelter-in-place orders to prevent the spread of the virus, the state’s industrial activity experienced an economic slowdown. This paper quantifies the changes in the atmosphere during the time of the COVID-19 slowdown over major cities in Texas and compares it to similar changes in Wuhan, China using satellite imagery.

A novel five-surface phosphor-in-ceramic (FS-PiC) for high illumination and excellent color uniformity in larger-scale LEDs for sensor light source application is demonstrated. YAG phosphor (Y3Al5O12:Ce3+) was uniformly mixed with ceramic and sintered at 680°C to form a phosphor wafer. A sophisticated laser engraving was employed on the phosphor wafer to form a saddle-shaped large-scale FS-PiC LEDs. The performance of the FS-PiC LEDs exhibited the illumination of 401lm, average color temperature (CCT) of 5488K±110K, and color coordinates (CIE) of (0.3179±0.003, 0.3352±0.003). In contrast to convention single-surface phosphor-in-ceramic (SS-PiC) LEDs, the performance exhibited the illumination of 380lm, average CCT of 5830K±758K, and CIE of (0.3083±0.07, 0.3172±0.07). These indicated that the performance of the FS-PiC LEDs was higher than the SS-PiC LEDs for illumination, CCT, and CIE of 1.1, 7, and 23 times, respectively. Furthermore, the FS-PiC LEDs demonstrate lower lumen loss of 2% and less chromaticity shift of 5.4x10-3 under accelerated aging at 350°C for 1008 hours, owing to the high ceramic melting temperature of up to 510°C. In this study, the proposed FS-PiC larger-scale LEDs having excellent optical performance and high reliability may be the promising candidates to replace the convention phosphor-in-organic silicone material used in high-power LEDs for the next generation of sensor light sources, display, and headlight applications.

Surface–subsurface soil-rock modeling is crucial for infrastructure design and groundwater yield optimization, especially in the complex crystalline basement terrains of Penang Island, Malaysia. This study conducted large-scale characterization of soil-rock profiles using ERT, SRT, rock quality designation, and soil penetration test (SPT N-values) data, optimized through regression modeling. The approach effectively identified soil-rock structures and their suitability to prevent structural failures and enhance groundwater productivity. Correlations between borehole lithologic logs and velocity–resistivity models revealed distinct soil compositions across the study area. The results highlighted thick, saturated, and loose silty to sandy bodies in the eastern to northern sections, contrasting with sandy compositions and penetrative fractures in the southern part. The study also found good correlations between rock mass quality and N-values for different soil types. Depths of intra-bedrock weathered/fractured units varied between 12 and >35 m. This has significant implications for determining optimal foundation depths in the study area. Groundwater productivity was associated with intra-bedrock planes of weakness at depths exceeding 40 m. Overall, this study developed empirical relations between geophysical and geotechnical parameters for wet tropical granitic terrains, filling critical gaps in understanding subsurface characteristics.

Human Immunodeficiency Virus (HIV) infection and its latent recurrent infection make vaccine development a significant challenge for traditional vaccines; however, the mRNA delivery of multiepitope antigens capable of creating antibodies against the surface proteins of HIV-1 and HIV-2 along with their respective Nef proteins, responsible for the latent infection can bring a most effective, as well as affordable solution to the unresolved epidemics of HIV. In this paper, we present the complete design of a multiepitope vaccine to prevent acute infections and inactivate Nef proteins that block the MHC-1 and MHC-2 pathways to hide the virus for later reinfection.

The implementation of a progressive rehabilitation training model to promote patients’ motivation efforts can greatly restore the damaged central nervous system function in patients. The patients’ active engagement can be effectively stimulated by assist-as-needed (AAN) robot rehabilitation training. However, its application in robotic therapy has been hindered by a simple determination method of robot assisted torque which focuses on the evaluation only of the affected limb's movement ability. Moreover, the expected effect of assistance depends on the designer, which deviates from the patient's expectations, and its applicability to different patients is deficient. In this study, we propose a control method with personalized treatment features based on the idea of estimating and mapping the stiffness of the patient’s healthy limbs. This control method comprises an interactive control module in the task-oriented space based on the quantitative evaluation of motion needs and an inner loop position control module for the pneumatic swing cylinder in the joint space. An upper limb endpoint stiffness estimation model is constructed and a parameter identification algorithm is designed. The upper limb endpoint stiffness which characterizes the patient's ability to complete training movements is obtained by collecting surface electromyographic (sEMG) signals and human-robot interaction forces during patient movement. Then the motor needs of the affected limb when completing the same movement are quantified based on the performance of the healthy limb. A stiffness mapping algorithm is designed to dynamically adjust the rehabilitation training trajectory and auxiliary force of the robot based on the actual movement ability of the affected limb, achieving AAN control. Experimental studies were conducted on a self-developed pneumatic upper limb rehabilitation robot, and the results showed that the proposed AAN control method can effectively estimate the patient's movement needs and achieve progressive rehabilitation training. The rehabilitation training robot that simulates the movement characteristics of the patient's healthy limbs drives the affected limb, making the intensity of the rehabilitation training task more in line with the patient's pre-morbid limb use habits, and also beneficial for the consistency of bilateral limb movements.

The study focuses on a novel porous TiNi-based material for ophthalmic orbital implants which was produced by self-propagating high-temperature synthesis (SHS) and, after proper surface modification, possesses a specific microstructure of its surface pores, which makes it attractive for biomedical use in implants. After preparation via SHS, the obtained porous TiNi material was etched in acidic environment, to get rid of its surface Ti2Ni secondary-phase particles. This was found to improve the material’s surface morphology, adding micro-roughness to its macro-rough pores. As a result, cell growth tests conducted on the material demonstrated improved cell adhesion and growth kinetics on such a porous material with improved roughness. Finally, the material was tested in vivo as an ophthalmic orbital implant, demonstrating good biocompatibility, good degree of biointegration with surrounding eyeball tissues, and no signs of rejection after as long as 180 days. Thus, the novel porous TiNi-based material shows promise for its use in ophthalmic implantology, for instanse for manufacturing musculoskeletal stumps of the eyeball after evisceration, as it is biocompatible, has a high tissue-implant integration potential and demonstrates reduced risks of exposure and rejection of the implant.

This work deals with a novel porous TiNi-based material for ophthalmic orbital implants that was produced by high-temperature synthesis (SHS) and possesses a specific microstructure of its surface pores, which makes it attractive for biomedical use in implants. After preparation via SHS, the obtained porous TiNi material was etched in acidic environment, to get rid of its surface Ti2Ni secondary-phase particles. This was found to improve the material’s surface morphology, adding micro-roughness to its macro-rough pores. As a result, cell growth tests conducted on the material demonstrated improved cell adhesion and growth kinetics on such a porous material with improved roughness. Finally, the material was tested in vivo as an ophthalmic orbital implant, demonstrating good biocompatibility, good degree of biointegration with surrounding eyeball tissues, and no signs of rejection after as long as 180 days. Thus, the novel porous TiNi-based material shows promise for its use in ophthalmic implantology, for instanse for manufacturing musculoskeletal stumps of the eyeball after evisceration, as it is biocompatible, has a high tissue-implant integration potential and demonstrates reduced risks of exposure and rejection of the implant.

The enzyme-linked immunosorbent assay (ELISA) coupled with surface-enhanced Raman spectroscopy (SERS) detection is a growing area of analytical chemistry emerged as a solution to a problem of sensitivity improvement. SERS-based ELISA with horseradish peroxidase as an enzymatic label, o-phenylenediamine (oPD) substrate, and 2,3-diaminophenazine (DAP) enzymatic product was one of the first examples of such systems. Surprisingly, the full potential of this long-known approach has not been revealed yet. The current study addresses a previously neglected problem of SERS detection stage performance. Using silver nanoparticles and model mixtures of oPD and DAP, the effects of pH, concentration of aggregating agent, and particle surface chloride stabilizer were extensively evaluated. At optimal mildly acidic pH of 3, 0.93 to 1 M citrate buffer, and AgNPs stabilized with 20 mM chloride, at least two orders of magnitude advantages in the detection limits of SERS over colorimetry both for DAP and HRP were demonstrated. We suppose that this improved detection system could become a useful tool for the development of SERS-based ELISA protocols.

The study used ERA5 reanalysis SST dataset re-gridded to a common grid of 0.25° X 0.25° spatial resolution (latitude × longitude) for the historic (1940–2014) and projected (2015–2100). The SST simulation under the SSP5-8.5 scenarios was carried out with output from 8 General Circulation Models (GCMs). The bias-corrected dataset was developed using Empirical Quantile Mapping EQM for the historical (1940-2015) and the future (2030-2100) while the CMIP6 model simulation was evaluated against the ERA5 monthly rainfall observed data for monthly and annual sea surface temperatures (SST) over the Gulf of Guinea. ). The CMIP6 models simulation for SST projection from 2030-20100 based on SSPS 8.5 SST is projected to increase by 4.61o (31oC) in 2030 to 35oC in 20100 in the coastal GOG and 2.6oC in the Western GOG (Sahel). The correlation coefficient (r) was used to evaluate the performance of the CMIP6 models and the analysis showed ACCESS 0.1,CAMS CSM 0.2, CAN ESM 0.3, CMCC, 0.3 and MCM, 0.4 indicating that all models performed well in capturing the climatological pattern of the SST. The.CMIP6 bias corrected model simulations showed increased SST warming over the GOG will be higher in the Far period end than the Near-term climate. The study affirmed that the CMIP6 projections can be used for multiple assessments related to climate and hydrological impact studies and for the development of mitigation measures under a warming climate

Keywords: Interspecific competition; Character displacements, Behavioral syndrome; Foraging; Pecking; Probing; Sweeping; Ballistic transport, Surface tension transport; Lingual transport

Lots of efforts are made to optimize spectrum quality used for indoor farming to maximize artificial light utilization and reduce water loss. For such an improvement, green (G) light supplementation to a red-blue (RB) background was successfully employed in our previous studies to restrict both non-photochemical thermal dissipation (NPQ) and stomatal conductance (gs). At the same time, however, the downregulation of NPQ and gs influences the leaf temperature (Tleaf) in opposite ways. Thus, to elucidate which factor plays a more prominent role in Tleaf regulation and whether such response is temporal or permanent we investigated the correlation between NPQ or gs and the subsequent Tleaf. To this end, we analysed tomato plants (Solanum lycopersicum L. cv. Malinowy Ozarowski) grown solely under monochromatic LED lamps (435, 520, or 662 nm; 80 µmol m–2 s–1) or under mixed RGB spectrum (1:1:1; 180 µmol m–2 s–1), and simultaneously measured the gs and Tleaf with an infrared gas analyser and thermocouple or employed infrared thermal camera (FLIR) during thermal imaging analyses. Results documented that growth light quality significantly modified the Tleaf, and such response is not temporal. Furthermore, we found that plants' actual adaxial leaf surface temperature is more closely related to NPQ amplitude, while the temperature of the abaxial surface corresponds to gs.

This paper presents the concept of a novel adaptable sensing solution currently being developed under the EU Commission founded PHOTONGATE project. This concept will allow to quantify multiple analytes of the same or different nature (chemicals, metals, bacteria, etc.) in a single test with levels of sensitivity and selectivity at/or over those offered by current solutions. PHOTONGATE relies on two core technologies: a bio-chemical technology (molecular gates) which will confer the specificity and, therefore, the capability to be adaptable to the analyte of interest, and which combined with porous substrates will increase the sensitivity, and a photonic technology based on Local Surface Plasmonic Resonance (LSPR) structures serves as transducer for light interaction. Both technologies are in the micron range, facilitating the integration of multiple sensors within a small area (mm²). The concept will be developed for its application in health diagnosis and food safety sectors. It is thought as an easy-to-use modular concept, which will consist of the sensing module, mainly of a microfluidics cartridge that will house the photonic sensor, and a platform for fluidic handling, optical interrogation, and signal processing. The platform will include a new optical concept, fully Europe Union Made, avoiding optical fibers and expensive optical components.

The paper considers the issues of structural stability, electronic properties, and phonon dispersion of the cubic, tetragonal, and monoclinic phases of ZrO2. It was found that the monoclinic phase of zirconium dioxide is the most stable among the other two phases in terms of total energy, lowest enthalpy, highest entropy, and other thermodynamic values. The smallest negative modes were found for m-ZrO2. An analysis of the electronic properties showed that during the m–t phase transformation of ZrO2, the Fermi level first shifts by 0.125 eV towards higher energies, and then decreases by 0.08 eV in the t–c cross section. The band gap for c-ZrO2, t-ZrO2, and m-ZrO2 is 5.140 eV, 5.898 eV, and 5.288 eV, respectively. Calculations based on the analysis of the influence of doping 3.23, 6.67, 10.35 and 16.15 mol. %Y2O3 on the m-ZrO2 structure showed that the enthalpy of m-YSZ decreases linearly, which accompanies further stabilization of monoclinic ZrO2 and an increase in their defectiveness. In this case, the position of the Fermi level changes abruptly, and the energy gap decreases. It has been established that not only for pure systems, including those doped with Y2O3, the main contribution to the formation of the conduction band is made by the p-states of electrons. An analysis of the mechanism of water adsorption on the surface of t-ZrO2 (101) and t-YSZ (101) showed that H2O on unstabilized t-ZrO2 (101) is adsorbed dissociatively with an energy of -1.22 eV, as well as by the method of molecular chemisorption with an energy of -0.69 eV and the formation of a hydrogen bond with a bond length of 1.01 Å. In the case of t-YSZ (101), water is molecularly adsorbed onto the surface with an energy of -1.84 eV. Dissociative adsorption of water occurs at an energy of -1.23 eV, near the yttrium atom.

Good hand hygiene has proven to be essential in reducing the uncontrolled spread of human pathogens. Cold atmospheric plasma (CAP) may provide an alternative to disinfecting hands with ethanol-based handrubs when hand washing facilities are unavailable. CAP can be safely applied to the skin if the energy is well controlled. In this study, RF and DC plasma sources was built with a pin-to-mesh electrodes configuration inside a fused silica tube of 5 mm of inner diameter. Microbiological assays based on EN 13697:2015+A1:2019 using Escherichia coli DSM 682 or Staphylococcus epidermidis DSM 20044 were used to examine the antimicrobial effect of various plasma conditions. Metal and silicone disks that model skin were used as inoculation matrices. The prototype air radio frequency (RF) CAP achieved significant disinfection in the MHz range on stainless steel and silicone substrates. This is equivalent to half the performance of direct current CAP, which is only effective on conductive substrates. Using only electricity and air CAP could, with further optimization, replace or complement current hand disinfection methods, and mitigate the economic burden of public health crises in the future.

The paper deals with one new property of the linear time-optimal control problems with real eigenvalues of the system, no matter of the number of eigenvalue multiplicity. This property unveils a prospective of synthesizing the time-optimal control without the need of describing the switching hyper-surfaces. The already chrestomathy example of the time-optimal control of a double integrator is resolved by the new technique and compared with the classical synthesis.

This work presents a new scheme for autonomous control and obstacle detection of a catamaran unmanned surface vessel. Based on the Newtonian mechanics, hydrodynamics, and maneuvering modelling group modelling principles in the attached coordinate system, a three-degree-of-freedom motion model of the catamaran unmanned surface vessel is constructed. The fuzzy inference method is used to overcome the drawback that the traditional PID control cannot tune the PID parameters online, and the trajectory controller is designed. Meanwhile, 3D LIDAR is used to achieve obstacle detection. The results of the trajectory tracking simulations and experiments verify the accuracy of the model design and the effectiveness of the autonomous control design.

Ecuador is the world's fifth largest cocoa producer, generating hundreds of annual tons of residues from this fruit. This research aims to value this residual (cocoa pod husk) by using it as raw material to obtain pectin, which is widely used in the food and pharmaceutical industries. For them, the extraction of three different organic acids with GRAS status (and therefore safe for their use), citric, malic and fumaric acids, were studied. In addition, two other factors, temperature (70-90°C) and extraction time (60-90 min), were explored in a central composite design of experiments. Under the conditions of the experiment, it was obtained that the best yields were reached for citric acid, malic acid and fumaric acid and for ~86 min of extraction time. The temperature did not show a significant influence on the yield. The pectins obtained under optimal conditions were characterised, showing their similarity with commercial pectin. However, the equivalent weight and the esterification degree of the pectin obtained with fumaric acid classify it as having a high equivalent weight and a low degree of esterification. It differs significantly from the other two acids, perhaps due to the limited solubility of fumaric acid.

Hybrid organic-inorganic (dendritic polymer-silica) xerogels containing silver nanoparticles (Ag-Nps) were developed as antibacterial leather coatings. The preparation method is environmentally friendly, based on two biomimetic reactions. Silica gelation and spontaneous (Ag-Np) formation were both mediated by hyperbranched poly (ethylene imine) (PEI) scaffolds of variable Mw (2000-750000). The formation of precursor hydrogels was monitored by dynamic light scattering (DLS). The chemical composition of the xerogels was assessed by Infra-Red Spectroscopy (IR) and Energy-dispersive X-ray spectroscopy (EDS) while the uniformity of the coatings was established by scanning electron microscopy (SEM). Release properties of coated leather samples and overall behaviour in water in comparison to untreated analogs were investigated by UV-Vis spectroscopy. Antibacterial activity was tested towards Escherichia coli, Pseudomonas aeruginosa, and Staphylococcus aureus, and antibiofilm properties against Staphylococcus aureus, Staphylococcus epidermidis, Escherichia coli, Acinetobacter baumannii, Enterococcus faecalis while SARS-Cov-2 clinical isolate was employed for the first estimation of their antiviral potential. Toxicity was evaluated using the Jurkat E6.1-cell line. Finally, water contact angle measurements were implemented to determine the enhancement of the leather surface hydrophilicity caused by these composite layers. The final advanced products are intended for use in medical applications.

Films prepared from poly(3-hydroxybutyrate-co-4-hydroxybutyrate) copolymers produced by Aneurinibacillus sp. H1 using an automatic film applicator were homogeneous and had a defined thickness, which allowed a detailed study of physicochemical properties. Their properties were compared with a poly (3-hydroxybutyrate) homopolymer film prepared by the same procedure, which proved to be significantly more crystalline by DSC and XRD. Structural differences between samples had a major impact on their properties. With increasing 4-hydroxybutyrate content, the ductility and release rate of the model hydrophilic active ingredient increased significantly. Other observed properties, such as the release of the hydrophobic active substance, the contact angle with water and ethylene glycol, or the surface morphology and roughness, were also affected by the composition. The identified properties predetermine these copolymers for wide use in areas such as biomedicine or smart biodegradable packaging for food or cosmetics. The big advantage is the possibility of fine-tuning properties simply by changing the fermentation conditions.

We have suggested earlier a new sustainable method for permafrost thermal stabilization that combines passive screening of solar radiation and precipitation with active solar-powered cooling of the near-surface soil layer thus preventing heat penetration in depth. Feasibility of this method has been shown by calculations, but needed experimental proof. In this article, we are presenting the results of soil temperature measurements obtained at the experimental implementation of this method outside of the permafrost area which actually meant higher thermal loads than in Polar Regions. We have shown that near-surface soil layer is kept frozen during the whole summer, even at air temperatures exceeding +30°C. Therefore, the method has been experimentally proven to be capable of sustaining soil frozen even in more extreme conditions than expected in permafrost areas. In addition to usual building and structure thermal stabilization, the method could be used to prevent the development of thermokarst, gas emission craters, and landslides; greenhouse gases, chemical, and biological pollution from the upper thawing layers at least in the area of human activities; protection against coastal erosion; and permafrost restoration after wildfires. Using commercially widely available components, the technology can be scaled up for virtually any size objects.

Surface soil moisture (SSM) is a significant factor affecting crop growth. This paper presents a method for retrieving SSM over wheat-covered areas using synergy dual-polarization C-band Sentinel-1 synthetic aperture radar and Sentinel-2 optical data. Firstly, a modified water cloud model (WCM) was proposed to remove the influence of vegetation from the backscattering coefficient of the radar data. The vegetation fraction was then introduced in this WCM, and the vegetation water content (VWC) was calculated using multiple linear regression model. Subsequently, the support vector regression technique was used to retrieve the SSM. This approach was validated using in-situ measurements of the wheat field in Hebi, in the north of Henan Province. The key findings of this study are as follows: (1) Based on vegetation indices obtained from Sentinel-2; the proposed VWC estimation model can effectively eliminate the influence of vegetation; (2) compared with vertical transmit and horizontal receive polarization, vertical transmit and vertical receive polarization is better for detecting changes in SSM at different growth stages of wheat; and, (3) the validation results indicated that the proposed approach, based on Sentinel-1 and Sentinel-2 data, successfully retrieved SSM in the study area.

Nanometer-curved surfaces are abundant in biological systems as well as in nano-sized technologies. Properly functionalized polymer-grafted nanoparticles (PGNs) adhere to surfaces with different geometries and curvatures. This work explores some of the energetic and mechanical characteristics of the adhesion of PGNs to surfaces with positive, negative and zero curvatures using Coarse-Grained Molecular Dynamics (CGMD) simulations. Our calculated free energies of binding of the PGN to the curved and flat surfaces as a function of separation distance show that curvature of the surfaces critically impacts the adhesion strength. We find that the flat surface is the most adhesive, and the concave surface is the least adhesive surface. This somewhat counterintuitive finding suggests that while a bare nanoparticle is more likely to adhere to a positively curved surface than a flat surface, grafting polymer chains to the nanoparticle surface inverts this behavior. Moreover, we studied the rheological behavior of PGN upon separation from the flat and curved surfaces under external pulling force. The results presented herein can be exploited in drug delivery and self-assembly applications.

Land Surface Temperature (LST) estimation has been studied for several purposes, while the optimal method of estimating the LST has not been criticized yet. This research explores the optimum method in Land Surface Temperature (LST) estimation using LANDSAT-8 imagery data. Four different LST retrieval approaches, the Radiative Transfer Equation-based method (RTE), the Improved Mono-Window method (IMW), the Generalized Single-Channel method (GSC), and the Split-Window algorithm (SW), were calculated to present the LSTs over Buriram Town Municipality, Thailand. The calculated LSTs from these four methods were compared with the ground-based temperature data, taken on the same date and time of the employed LANDSAT-8 images. For this reason, the optimum method of the LST calculation was justified by considering the lowest normalized root means square error (NRMSE) values. As a result, the SW algorithm presents an optimum method in LST estimation. Regarding the SW, this algorithm requires not only the atmospheric profiles during satellite acquisition but also the retrieval of several coefficients. Besides, the LST retrieval method based on the SW algorithm is sensitive to water vapor content and coefficients. Although the SW algorithm is an optimum method explored in this study, it is emphasized that the adjustable values of coefficient response to the atmospheric state may be recommended. With these conditions, the SW algorithm can generate the land-surface temperature over the mixed land-use and land cover on the LANDSAT-8 images.

Semisolid casting of Aluminum alloys is growing. For magnesium alloys, Thixomoulding became the dominant process around the world. For aluminium processing, the situation is different as semisolid processing of aluminium is more technically challenging than for magnesium. Today three processes are leading the process implementation, The GISS method, the RheoMetal process and the SEED process. These processes have all strengths and weaknesses and will fit a particular range of applications. The current paper aims at looking at the strengths and weaknesses of the processes to identify product types and niche applications for each process based on current applications and development directions taken for these processes

Ocean surface heat fluxes play a significant role in the genesis and evolution of various marine-based atmospheric phenomena, from the synoptic scale down to the microscale. While in-situ measurements from buoys and flux towers will continue to be the standard in regards to surface heat flux estimates, they commonly have significant gaps in temporal and spatial coverage. Previous and current satellite missions have filled these gaps; though they may not observe the fluxes directly, they can measure the variables needed (wind speed, temperature, and humidity) to estimate latent and sensible heat fluxes. However, current remote sensing instruments have their own limitations, such as infrequent coverage, signals attenuated by precipitation, or both. The Cyclone Global Navigation Satellite System (CYGNSS) mission overcomes these limitations over the tropical and subtropical oceans by providing improved coverage in nearly all weather conditions. While CYGNSS (Level 2) primarily estimates surface winds, when coupled with observations or estimates of temperature and humidity from reanalysis data, it can provide estimates of latent and sensible heat fluxes along its orbit. This paper describes the development of the Surface Heat Flux Product for the CYGNSS mission, its current results, and expected improvements and changes in future releases.

The Greenland Ice Sheet is now the largest land ice contributor to global sea level rise, largely driven by increased surface meltwater runoff from the ablation zone, i.e. areas of the ice sheet where annual mass losses exceed gains. This small but critically important area of the ice sheet has expanded in size by ~50% since the early 1960s, and satellite remote sensing is a powerful tool for monitoring the physical processes that influence its surface mass balance. This review synthesizes key remote sensing methods and scientific findings from satellite remote sensing of the Greenland Ice Sheet ablation zone, covering progress in 1) radar altimetry, 2) laser (lidar) altimetry, 3) gravimetry, 4) multispectral optical imagery and, 5) microwave and thermal imagery. Physical characteristics and quantities examined include surface elevation change, gravimetric mass balance, reflectance, albedo, and mapping of surface melt extent and glaciological facies and zones. The review concludes that future progress will benefit most from methods that combine multi-sensor, multi-wavelength, and cross-platform datasets designed to discriminate the widely varying surface processes in the ablation zone. Specific examples include fusing laser altimetry, radar altimetry, and optical stereophotogrammetry to enhance spatial measurement density, cross-validate surface elevation change, and diagnose radar elevation bias; fusing optical imagery, radar imagery, and microwave scatterometry to discriminate between snow, liquid water, refrozen meltwater, and bare ice near the equilibrium line altitude; combining optical reflectance with laser altimetry to map supraglacial lake, stream, and crevasse bathymetry; and monitoring the inland migration of snowlines, surface melt extent, and supraglacial hydrologic features.

Dietary polyphenols exist in two forms; extractable polyphenols (EPP) or compounds solubilised by aqueous/organic solvents, and non-extractable polyphenols (NEPP) or compounds remain in the corresponding residues after the extraction. At present, most researchers focus on EEP fractions, while NEPP is neglected. Thus, this study aimed to release NEPP from the remaining powder residue of Barhi date palm kernels (BDPK) with acid hydrolysis. The related extraction conditions were determined and optimised using response surface methodology (RSM) for maximisation of NEPP with highest cytotoxic and antioxidant activities. The face-centred central composite design (FCCCD) was used to establish treatments based on three independent variables, namely; extraction temperature, time, and solvent/sample ratio. Under the optimal conditions, the experimental values for DPPH radical-scavenging capacity of NEPP (IC50=57.52µg/mL), and cytotoxicity of NEPP against A549 and HT29 cells were IC50=17.4 µg/mL and 31.4µg/mL, respectively. The experimental values were in agreement with those predicted by RSM models, confirming the suitability of the model employed and the success of RSM for optimisation of the extraction conditions for NEPP from BDPK. These results indicate that NEPP from industrial date fruit waste could be a promising candidate as natural antioxidants with significant antiproliferation effect against A549 and HT29 cancer cells in-vitro.

An increasing number of aircraft is equipped with wing tip devices, which either are installed by the aircraft manufacturer at the production line or are retrofitted after the delivery of the aircraft to its operator. Installation of wing tip devices has not been a popular choice for regional turboprop aircraft and the novelty of the current study is to investigate the feasibility of retrofitting the British Aerospace (BAe) Jetstream 31 with an appropriate wing tip device (or winglet) to increase its cruise range performance, taking also into account the aerodynamic and structural impact of the implementation. To the best of the knowledge of the authors, no previous study exists which has attempted to assess the winglet retrofit of an existing aircraft type of similar size and operating profile. The optimal winglet design achieved a 2.38% increase of the maximum range by reducing the total drag by 1.19% at a mass penalty of 3.25%, as compared with the baseline aircraft configuration. Other designs were found to be more effective in reducing the total drag, but the structural reinforcement required for their implementation outweighed the achieved performance improvements. Since successful winglet retrofit programs for typical short to medium range narrow body aircraft report even more than 3% of block fuel improvements, undertaking the project of installing an optimal winglet design to the BAe Jetstream 31, should also consider a Direct Operating Cost (DOC) assessment on top of the aerodynamic and structural aspects of the retrofit.

A number of experimental and numerical studies point out that incorporating a rotating cylinder can superiorly enhance the aerofoil performance, especially for higher velocity ratios. Yet, there have been less or no studies exploring the effects of lower velocity ratio at a higher Reynolds number. In the present study, we investigated the effects of Moving Surface Boundary-layer Control (MSBC) at lower velocity ratios (i.e. cylinder tangential velocity to free stream velocity) and higher Reynolds number on a symmetric aerofoil (e.g. NACA 0021) and an asymmetric aerofoil (e.g. NACA 23018). In particular, the aerodynamic performance with and without rotating cylinder at the leading edge of the NACA 0021 and NACA 23018 aerofoil was studied on the wind tunnel installed at Aerodynamics Laboratory. The aerofoil section was tested in the low subsonic wind tunnel, and the lift coefficient and the drag coefficient were studied for different angles of attack. The experiments were conducted for two Reynolds numbers: 200000 and 250000 corresponding to two free stream velocities: 20 m/s and 25 m/s, respectively, for six different angle of attacks (-5°, 0°, 5°, 10°, 15° and 20°). This study demonstrates that the incorporation of a leading edge rotating cylinder results in an increase of lift coefficient at lower angle of attacks (maximum around 33%) and delay in stall angle (from 10° to 15°) relative to the aerofoil without rotating cylinder.

This work investigates the use of Non-destructive tests as a tool for monitoring the structural performance of concrete structures. The investigation encompassed four phases; the first of which involved the use of destructive and non-destructive mechanisms to assess concrete strength on cube specimens. The second phase research focused on site assessment for a twin engineering theatre located at the Faculty of Engineering, University of Lagos using rebound hammer and ultrasonic pulse velocity tester. The third phase was the use of linear regression analysis model with MATLAB to establish a relationship between calibrated strength as well as ultrasonic pulse velocities with their corresponding compressive strength values on cubes and values obtained from existing structures. Results show that the root-mean squared-R² values for rebound hammer ranged between 0.275 and 0.742 while ultrasonic pulse velocity R² values were in the range of 0.649 and 0.952 for air curing and water curing systems respectively. It initially appeared that the Ultrasonic pulse velocity was more suitable for predicting concrete strength than rebound hammer but further investigations showed that the latter was adequate for early age concrete while the former was more suited for aging concrete. Hence, a combined use is recommended in this work.

Additive manufacturing (AM) of high strength Al alloys promises to enhance the performance of critical components related to various aerospace and automotive applications. The key advantage of AM is its ability to generate lightweight, robust, and complex shapes. However, the characteristics of the as-built parts may represent an obstacle to satisfy the part quality requirements. The current study investigates the influence of selective laser melting (SLM) process parameters on the quality of parts fabricated from different Al alloys. A design of experiment (DOE) is used to analyze relative density, porosity, surface roughness, and dimensional accuracy according to the interaction effect between the SLM process parameters. The results show a range of energy densities and SLM process parameters for the AlSi10Mg and Al6061 alloys needed to achieve “optimum” values for each performance characteristic. A process map is developed for each material by combining the optimized range of SLM process parameters for each characteristic to ensure good quality of the as-built parts. The second part of this study investigates the effect of SLM process parameters on the microstructure and mechanical properties of the same Al alloys. This comprehensive study is also aimed at reducing the amount of post-processing needed.

Impervious surface mapping with high-resolution remote sensing imagery has attracted increasing interest as it can provide detailed information for urban structure and distribution. Previous studies have suggested that the combination of LiDAR data and high-resolution imagery for impervious surface mapping performs better than using only high-resolution imagery. However, due to the high cost of the acquisition of LiDAR data, it is difficult to obtain the multi-sensor remote sensing data acquired at the same acquisition time for impervious surface mapping. Consequently, real landscape changes between multi-sensor remote sensing data at different acquisition times would lead to the error of misclassification in impervious surface mapping. This issue has mostly been neglected in previous works. Furthermore, the observation differences generated from multi-sensor data, including the problems of misregistration, missing data in LiDAR data, and shadow in high-resolution images would also challenge the final mapping result in the fusion of LiDAR data and high-resolution images. In order to conquer these problems, we propose an improved impervious surface mapping method incorporating both LiDAR data and high-resolution imagery at different acquisition times in consideration of real landscape changes and observation differences. In the proposed method, a multi-sensor change detection by supervised multivariate alteration detection is employed to obtain changed areas and misregistration areas. The no-data areas in the LiDAR data and the shadow areas in the high-resolution imagery are extracted by independent classification yielded by its corresponding single sensor data. Finally, an object-based post-classification fusion is proposed to take advantage of independent classification results with single-sensor data and the joint classification result with stacked multi-sensor data. Experiments covering the study site in Buffalo, NY, USA demonstrate that our method can accurately detect landscape changes and obviously improve the performance of impervious surface mapping.

Friction and wear take place on two solid surfaces in sliding contact as a result of the mechanical, thermal and chemical interactions with the participation of environmental species. Electron microscopy and the associated spectroscopic analyses are powerful in probing these mechanisms in spatial resolutions from micro to atomic scale. This article provides a review of the author’s work in the wear and friction mechanisms of PVD hard coatings in which various SEM- and TEM-based microscopic and spectroscopic techniques were employed. Understanding on the failure mechanisms and the origin of self-adaptive friction has been improved to nano-scale. Other related issues are also discussed, such as sample preparation techniques for cross-sectional electron microscopy, energy dispersive X-ray spectroscopy and electron energy loss spectroscopy.

Titanium dioxide (TiO₂) micro and nano architectures have been intensively studied in the past years because of many varied applications in environmental, energy conversion, and storage fields, such as heterogeneous catalysis, dye-sensitized solar cells, lithium/sodium ion batteries, lithium-sulfur (Li-S) batteries, and bio-nanotechnology, etc. Especially the surface and interface structures in the TiO₂ structures play important roles in those applications. This mini review article focuses on TiO₂ micro and nano architectures with the prevalent crystal structures (anatase, rutile, brookite, and TiO₂(B)), and summarizes major advances in the surface and interface engineering and applications in environmental and electrochemical applications. We present the principles and growth mechanisms of TiO₂ nanostructures via different strategies, with an emphasis on rational control of the surface and interface structures. We further discuss the applications of TiO₂ micro and nano architectures in photocatalysis, lithium/sodium ion batteries, and Li-S batteries. Throughout the discussion, the relationship between the device performance and the surface structures of TiO₂ micro/nano structures will be highlighted. Then we discuss the phase transitions of TiO₂ nanostructures and possible strategies of improving the phase stability. The review concludes with a perspective on the current challenges and future research directions.

The alteration of the delicate balance that regulates the secretion and distribution of the tear film determines the dry eye (DE) syndrome, because the tear film represents the interface between the eye and the environment. Despite having a multifactorial origin, the main risk factors for the emergence of the ocular disease are female gender and advanced age. Likewise, morphological changes in several glands and in chemical composition of their secretions such as proteins, mucins, lipidics, aqueous tears, and salinity, are highly relevant factors to maintain a condition of good health of the ocular anterior segment. Another key factor of recurrence and onset of the disease is the presence of local and/or systemic infiammation that reflex on the ocular surface. However, it is one of the most commonly encountered disease in clinical practice and many other causes related to daily life and to lengthen the average life will contribute to the beginning. This review will consider how and what disorders of the ocular surface are responsible for a widespread pathology so. In the end, the most appropriate and new therapies will be briefly exposed according to the specific pathology.

Motivated by diffraction experiments on the $\left(2\sqrt{3}\times \sqrt{3}\right)\mathrm{R}{30}^{\circ }$ reconstructed Si(111) due to deposition of rare earth elements (Dy, Tb) and silicide formation we analyse the splitting and non-splitting of superstructure spots. For this purpose, we model diffraction patterns for one dimensional structures generated by the binary surface technique and use supercell models to keep the analysis simple. Diffraction pattern are calculated in the framework of the kinematical diffraction theory and they are analyzed as a function of the domains and domain boundaries. Basic properties of the diffraction pattern are analyzed for model systems of a two-fold and a three-fold periodicity. The rules derived from these calculations are applied to the "real-world" system of Si(111)-($\left(2\sqrt{3}\times \sqrt{3}\right)\mathrm{R}{30}^{\circ }$)-RESi$2_{}$ (RE = Dy or Tb). Depending on the combination of domains and domain boundaries of different types a plethora of different features are observed in the diffraction patterns. These are analyzed to determine the sizes of both domain boundaries and domains from experimentally observed splitting of specific superstructure spots.

We have collected theoretical arguments supporting the functional role of nano-metallic coatings of solar cells, which enhance their efficiency via by plasmon strengthening of absorption of sun-light photons and reduction of binding energy of photo-excitons. The quantum character of plasmonic effect related with the absorption of photons (called as optical plasmonic effect) is described in terms of Fermi golden rule for quantum transitions of semiconductor band electrons induced by plasmons from a nano-metallic coating. The plasmonic effect related with the lowering of exciton binding energy (called as electrical plasmonic effect) is also quantumly characterized with particular significance for metalized perovskite solar cells. Quantum coupling between plasmons in nanoparticles from a coating with band electrons in a semiconductor substrate significantly modifies material properties (dielectric functions) both of particles and of a semiconductor, beyond the ability of a classical electrodynamics description.

Re-purposing wastewater is necessary to circumvent water shortage for vegetable farmers in urban areas and to reduce public health hazards associated with using contaminated water for irrigation. In this study, the efficiency of biochar filtration systems in removing contaminants from wastewater was investigated. The hydraulic retention time (HRT) and the cleaning mechanism of coconut biochar filtration systems were examined. The filtration systems were designed with biowastes, specifically coconut biochar, as an adsorbent to remove pollutants from wastewater. Two setups of bed, 40 cm and 30 cm thick, were examined under different HRTs. Fourier Transform Infrared Spectroscopy (FTIR) analysis and Scanning Electron Microscopy (SEM) imaging were used to ascertain the properties of the biochar that enhances the removal of pollutants in wastewater. For both setups, the removal of heavy metals (Lead, Pb and copper, Cu) as well as Total Coliform (TC) was judged satisfactory but appeared ineffective in removing E. coli.

Background/Objectives: Human Papillomavirus (HPV)-related biomarkers, specifically E6 oncoproteins and anti-E6 antibodies, have emerged as promising indicators for detecting HPV-associated oral cavity cancers through salivary fluid analysis. This study assessed the survival outcomes of oral cancer patients who were double positive for these candidate biomarkers. Methods: Using biosensor immunoassays, we simultaneously detected E6 oncoprotein and anti-E6 antibodies in oral rinse fluids from patients with advanced T3/T4 oral cancer. Results: Preliminary findings revealed that over one-third of these patients had detectable HPV-related biomarkers in their saliva, with 37.9% testing positive for E6 oncoprotein and 31.0% showing elevated anti-E6 antibody levels. Double positivity was observed in 24.1% of cases. Although survival rate differences between the groups were not statistically significant, the double positivity subgroup demonstrated a trend toward improved survival outcomes compared to single-positive or double-negative patients. Conclusions: These initial results suggest that simultaneous detection of E6 oncoprotein and anti-E6 antibodies could be potential saliva-based biomarkers for clinical applications. Using surface plasmon resonance (SPR) techniques to identify double positivity may enhance early detection of HPV-related oral cancer, potentially informing more effective treatment strategies in clinical practice.

In this study, a novel method is proposed to estimate surface-spectral reflectance from camera responses that combines model-based and training-based approaches. An imaging system is modeled using the spectral sensitivity functions of an RGB camera, spectral power distributions of multiple light sources, unknown surface-spectral reflectance, additive noise, and a gain parameter. The estimation procedure comprises two main stages: (1) selecting the local optimal reflectance dataset from a reflectance database and (2) determining the best estimate by applying a neural network to the local optimal dataset only. In stage (1), the camera responses are predicted for the respective reflectances in the database, and the optimal candidates are selected in the order of lowest prediction error. In stage (2), most reflectance training data are obtained by a convex linear combination of local optimal data using weighting coefficients based on random numbers. A feed-forward neural network with one hidden layer is used to map the observation space onto the spectral reflectance space. In addition, the reflectance estimation is repeated by generating multiple sets of random numbers, and the median of a set of estimated reflectances is determined as the final estimate of the reflectance. Experimental results show that the estimation accuracies exceed those of other methods.

The accumulation of sea surface debris around the coastal waters of Malta poses significant ecological and environmental challenges, negatively affecting marine ecosystems and human activities. This issue is exacerbated by the lack of an effective system tailored to predict surface debris movement specifically for the Islands of Malta. To address this gap, a pipeline that combines a machine learning (ML) based prediction system with a physics-based model is proposed. This pipeline uses historical sea surface currents (SSC) velocities data to forecast future conditions and visualise debris movement. Central to this system are LSTM and GRU models, trained to predict SSC velocities for the next 24 hours for a specific area. These predictions are then utilised by a Lagrangian model to simulate and visualise the debris movement, providing insights into future dispersion patterns. A comparative evaluation of the models showed that the LSTM model outperformed the GRU model, with lower error metrics such as mean absolute error (MAE), mean squared error (MSE), and root mean squared error (RMSE), alongside narrower interquartile ranges (IQR). This method offers a tailored approach to addressing sea surface debris around Malta by accurately predicting SSC velocities and visualising debris movement, improving cleanup operations, and marine conservation strategies.

Brushless Direct Current Motors are significantly improved for using many electrical applications. The design investigation is increased year by year and most of the motor design researchers find out the superior efficiency of the BLDC motor. The traditional motor consumed more electrical power than BLDC motor. The design of BLDC motors that are compact, small, easy to control, save energy and light weight. Due to this fact, the design of BLDC motor should be analyzed to improve the motor characteristics performance. The research focuses on the design of BLDC motor performance using Taguchi Method and Response Surface Methodology (RSM) for Finite Element Method (FEM). Firstly, the Taguchi Method is applied to identify the optimization point of design parameters and consider using the reference model of actual BLDC electric fan motor with a rated power of 26Watts design. Based on the Taguchi Method to create the RSM is used to two-step optimization design performance using in FEM analysis. The performances of motor design proposed approach to provide the effeteness for motor design investigator. In this investigation aims the better structural performances in output power, torque, efficiency and torque ripple. The final design of proposed model achieved an energy efficiency is 10% higher than the reference design of prototype modes, the output power result is 10W higher this reference design. We can reduce the loss of the proposed motor design. Furthermore, the maximum torque can also increase the 0.032Nm of that design. The design simulation results were produced and studied by the FEM analysis of JMAG software. From the evaluation results, the configurations of reference model design are compared with the proposed design by using the three methods of motor design optimization showed the best characteristics for performance of motor investigation design.

This article describes the history of research and development of surface-penetrating radar, starting from the 60s in the USSR, and ending today in Russia and neighboring states formed after the collapse of the USSR. The outstanding role played in the initial period of this technology development by Prof. M.I. Finkelstein and his colleagues is highlighted. Their research had a significant impact on subsequent developments in modern Russia and the neighboring countries.

At 12:28 UTC (8:28 PM, local time) on 15 January 2023, a shallow, moderate earthquake with a magnitude (Mw) of 4.7 and a depth of one (1) kilometer shook the northern part of Leyte Island in the central part of the Philippines. The ground shaking was felt at PHIVOLCS Earthquake Intensity Scale (PEIS) VI, (very strong) equivalent to Modified Mercalli Intensity (MMI) VI in areas along the strike of the Leyte segment of the Philippine Fault. Even though this earthquake is classified as moderate in size, significant geologic, structural, and socio-economic impacts were documented. Most of the earthquake impacts that include surface rupture, liquefaction, and mass movements are limited near the epicentral area. The earthquake produced an 8-km-long surface rupture, the first documented rupture generated by a magnitude <6 along the Philippine Fault, and is unusual in other surface rupturing earthquakes worldwide. It injured 18 persons and damaged 434 residential buildings and 26 public infrastructures which amounts to about 500 thousand US dollars. Structural damages were caused by surface rupture and/or poor engineering construction practices. Analysis of the seismic waveform and recorded peak ground acceleration (PGA) suggests that the subsurface geology influenced the ground motion amplification in an area near the epicenter. Based on the hypocenter, focal mechanism solution, aftershock distribution, and actual field observation, the causative fault for this event is the northern end of the Philippine Fault – Leyte segment. Moderate in size, this earthquake emphasizes the need and importance of documenting moderate-sized earthquakes as a tool and guide for medium and long-term earthquake risk assessment and resiliency.

The paper is devoted to the study of a high-pressure short-arc xenon discharge, which is widely used as a light source. Cathodes of such lamps are often doped with thorium for better cathode operation. As a result, thorium can evaporate into a discharge. The study is based on a model of a short-arc xenon discharge plasma, which includes presence of thorium atoms in the plasma. The data obtained show that thorium atoms strongly affect the characteristics of the plasma, reducing its temperature, changing the ionic composition near the cathode, energy balance and generation of optical radiation. Especially interesting is the case when the discharge electrodes have a different shape of the working surface: the anode has a convex or concave shape; the cathode has a different cone angle. The obtained data make it possible to propose a new way to increase the luminous efficiency of xenon lamps due to the appropriate choice of the electrodes working surface shape, which turned out to be an unexpectedly strong factor of affecting plasma characteristics. This, in turn, allows us to develop xenon lamps with the desired characteristics providing optical radiation in the required range of the spectrum and better use of energy.

The urban heat island (UHI) and its intensity is one of the phenomena that are of determining importance for the comfort of living in cities and their sustainable development in the face of deepening climate change. The study is objectively difficult due to the large dynamics like land cover and the considerable diversity of land use patterns in urban areas. Various approaches and methods are used in research practice, based both on ground measurements and in the use of remote methods and satellite information. However, most of these approaches provide information with problematic spatial and temporal resolution, making them difficult to apply for sustainable urban planning purposes, which require adequate information provision. This paper presents the results of the application of thermal photogrammetry based on the use of unmanned aerial systems (UAS), combined with geographic information systems (GIS), in the study of surface urban heat island intensity (SUHI), at the local level for the largest housing complex in Bulgaria - Lyulin district of the capital of Sofia city. The studies were carried out during a heat wave in July 2023. A difference of 16.5oC was found between locations with SUHI occurrence and suburban areas. The information benefits of locally addressed data and their direct applicability are discussed to support decision-making processes in the planning and management of urban areas, including their climate adaptation and sustainable development.

Graphene materials synthesized using direct laser writing (laser-induced graphene; LIG) are fa-vorable sensor materials because of their large surface area, ease of fabrication, and cost effec-tiveness. In particular, LIG decorated with metal nanoparticles (NPs) has been used in various sensors, including chemical sensors and electronic and electrochemical biosensors. However, the effect of metal decoration on LIG sensors remains controversial; hypotheses based on computa-tional simulations do not always match experimental results, and even experimental results re-ported by different researchers have not been consistent. In the present study, we explored the effects of metal decorations on LIG gas sensors, with NO2 and NH3 gases as representative oxi-dizing and reducing agents, respectively. To eliminate unwanted side effects arising from metal salt residues, metal NPs were directly deposited by vacuum evaporation. Although the gas sen-sitivities of the sensors deteriorate upon metal decoration irrespective of the metal work function in the case of NO2 gas, they improve upon metal decoration in the case of NH3 exposure. A careful investigation of the chemical structure and morphology of the metal NPs in the LIG sensors shows that the spontaneous oxidation of metal NPs with a low work function changes the be-havior of the LIG gas sensors and that the sensor behaviors under NO2 and NH3 gases follow different principles.

Land surface temperature (LST) is a crucial parameter in climate and ecology, exerting significant influence on meteorological conditions, ecosystems, and human life. LST data sources are diverse, with remote sensing being the prevailing means of acquisition. FY-4A/AGRI offers high-quality LST products for East Asia. In this study, we evaluated the performance of the product in Hunan Province and conducted refined analysis of surface heat resources based on the 4km/1h resolution product over a two-year period. The results demonstrate that the FY-4A LST product effectively captures surface temperature (R=0.893), albeit with a relatively high error level (Bias=-6.295℃; RMSE=8.58℃), particularly in capturing high LST values. The performance of this product is superior in the eastern flat terrain area of Hunan Province compared to its performance in the western mountainous region due to environmental conditions causing systematic errors that contribute to instability in detection deviation for this product. Surface heat resources are more abundant in eastern Hunan Province than in mountainous areas located west and southwardly, and the detailed distribution of them at finer scales is mainly influenced by the terrain and climate conditions. There is no obvious seasonal difference in the distribution of heat resources except in winter, and rapid urbanization within Chang-Zhu-Tan urban agglomeration during two years has significantly altered the spatial distribution pattern of surface heat resources across Hunan Province. These findings provide a quantitative baseline for assessing FY-4A satellite's detection capability while serving as a reference for further application of its LST products and establishing foundations for divisional classification and utilization strategies pertaining to surface heat resources within Hunan Province.

As wind turbine power requirements have evolved from the order of kilowatts (kW) to the order of several megawatts (MW), wind turbine components have been subjected to more demanding and critical operating conditions. The wind turbine must cope with higher wind loads due to larger blade sizes, which are also time-varying and ultimately higher power levels. One of the challenges in the manufacture of high-power wind turbines lies in the gearbox and consists of achieving ever greater power density without compromising efficiency, i.e., greater load capacity with lower weight (and production cost) and reduced power losses. In this paper we will analyze the influence that certain design parameters have on the size and weight of the gearbox components and therefore of the gearbox itself. For this purpose, the theoretical model of the gearbox will be planned and the influence of calculation parameters on the gearbox design will be analyzed. The influence of material, modulus and tooth width on the size and weight of the gearbox will be observed. Critical stresses are also calculated. The goal is to prepare the theoretical basis for an optimization process that will result in a gearbox as compact as possible without compromising the service life of the components.

The purpose of the review is to provide new insight into the potential of surface modification of carbon fibers for enhancing the application of the carbon fibers many a fold. To this end a total of 429 papers on the subject of surface modication of carbon fibers by a variety of chemical and electrochemical methods published during the period from 2010-2022 have been reviewed. Astounding results of surface funcationalization of carbon fibers by a variety of state of the art methods resulting in the unconventional applications of the resulting modified carbon fibers are summarized in a nut-shell in schemes from 1-6 towards the end of the review. Surface modifica-tion induces functionality to carbon fibers (CFs). The vitality of CF surface modification reac-tions could only be compared to the life process of respiration that sustains the multi functional-ity of living cells. Applicability of CFs can be drastically enhanced in incomprehensible ways by surface modification. Upon surface modification, inert and non-reactive CF surface becomes chemically active and functional with utility in diverse fields, namely, health, energy, environ-ment, defense, catalysis, smart materials and many others. Surface modification methods can be broadly classified into chemical, electrochemical and physical methods. By these surface modi-fication methods, the inert FC surface becomes polar. Surface properties like roughness, wetta-bility and energy are enhanced. Modification processes like sizing, oxidation, amination, si-lanization, polymerization, nanoarchitecture induces multifunctionality on CF surface. Modi-fied CFs when used as reinforcing material in carbon fiber reinforced plastics (CFRPs), im-proved bonding at the interface with resin matrices is observed with enhanced and outstanding mechanical properties (flexural strength, flexural modulus, IFSS, ILSS, hardness, elastic modulus, bending strength and compression strength).

We describe a machine learning (ML) approach to process the signals collected from Covid-19 optical-based detector. Multilayer Perceptron (MLP) and Support Vector Machine (SVM) were used to process both raw data and feature engineering data, and high performances for qualitative detection of the SARS-CoV-2 virus with concentration down to 1 TCID50/ml has been achieved. Valid detection experiments contain 486 negative and 108 positive samples; and control experiments, in which biosensors without antibody functionalization were used to detect SARS-CoV-2, contains 36 negative samples and 732 positive samples. Data distribution patterns of the valid and control detection dataset, based on T-distributed Stochastic Neighbor Embedding (t-SNE), was used to study the distinguishability between positive and negative samples, and explain the ML prediction performances. This work demonstrates that ML can be a generalized effective approach to process signals and dataset of biosensors dependent on resonant modes as biosensing mechanism.

Chronic gastroduodenal symptoms are prevalent worldwide, and there is a need for new diagnostic and treatment approaches. Several overlapping processes may contribute to these symptoms, including gastric dysmotility, hypersensitivity, gut-brain axis disorders, gastric outflow resistance, and duodenal inflammation. Gastric Alimetry® (Alimetry, New Zealand) is a non-invasive test for evaluating gastric function that combines body surface gastric mapping (high-resolution electrophysiology) with validated symptom profiling. Together, these complementary data streams enable important new clinical insights into gastric disorders and their symptom correlations, with emerging therapeutic implications. A comprehensive database has been established, currently comprising >2,000 Gastric Alimetry tests, including both controls and patients with various gastroduodenal disorders. From studies employing this database, this pa-per presents a systematic methodology for Gastric Alimetry test interpretation, together with an extensive supporting literature review. Reporting is grouped into four sections: Test Quality, Spectral Analysis, Symptoms, and Conclusions. This review compiles, assesses, and evaluates each of these aspects of test assessment, with discussion of relevant evidence, example cases, limitations, and areas for future work. The resultant interpretation methodology is recommended for use in clinical practice and research to assist clinicians in their use of Gastric Alimetry as a diagnostic aid, and is expected to continue to evolve with further development.

Snow-covered regions are the main source of reflection of incident shortwave radiation (ISR) on Earth’s surface. The deposition of light-absorbing particles (LAPs) on these regions increases the capacity of snow to absorb ISR and decreases surface snow albedo (SSA), which intensifies the radiative forcing leading to accelerated snowmelt and modifications of the hydrologic cycle. In this work we investigate changes in SSA and radiative forcing (RF) induced by LAPs in the Upper Aconcagua River Basin (Chilean central Andes) using remote sensing satellite data (MODIS), in-situ spectral SSA measurements, and the ISR (Chilean Solar Explorer platform) during the austral-winter months (May to August) for the 2004-2016 period. To estimate the changes in SSA and RF, we define two spectral ranges: i) an enclosed range (Ecr) between 841-876 nm, which isolates effects of Black-Carbon, an important LAP derived from anthropogenic activities, and ii) a broadband range (Bbr) between 300-2500 nm. Our results show that percent variations in SSA in the Ecr are higher than in the Bbr, regardless of the total amount of radiation received, which may be attributed to the presence of LAPs as these particles have a greater impact on SSA at wavelengths in the Ecr band than in the Bbr band.

The survey findings reveal that rivers worldwide carry an annual sediment load of 15 billion tons into the sea, and the Yellow River basin alone contributes 1.6 billion tons of sand. Therefore, understanding the science of wind and sand in the Yellow River is crucial to ensuring the safe development of similar basins across China and the world. This study examines the midstream wind and sand area of the Xiliugou tributary, a part of the upper Yellow River. The researchers used a stepped sand collector combined with an anemometer to measure the sand transport flux at 0-50 cm height on various underlying surfaces of the basin. Then, they estimated the amount of wind and sand entering the Yellow River using a function model based on the measured factors. Furthermore, the team analyzed the particle size composition of wind-eroded sand to better understand the principles of wind and sand erosion and accumulation in the basin. The results of the study show that the sand transport flux per unit area varies significantly across different underlying surfaces. Moreover, the contribution of moving sandy land, semi-fixed sand, and fixed sand to wind and sand deposition in the Yellow River basin was 77.08%, 15.30%, and 7.62%, respectively. The vertical change of sand transport rate on the basin's surface demonstrates that the total sand transport rate is an exponential function of wind speed. Based on this relationship, the researchers estimated that the total annual average wind and sand entering the Yellow River basin via the Xiliugou tributary is approximately 8.09×105t. Due to the basin's unique geography and sand source, the particle size composition of wind-eroded sand differs between the east and west sides of the river channel. On the west side, desert sand, mainly fine sand, and very fine sand constitutes the sand source. Conversely, on the east side, sand collected in the riverbed by secondary wind erosion is the primary sand source. Furthermore, human activities have disturbed the grain composition, mainly comprising powder and clay particles. This phenomenon, known as "wind-blown mud and water-washed sand," is evident in this geographical unit. In conclusion, the Yellow River basin still faces significant ecological security hazards. Understanding the coupling relationship between desert-basin-sand and wind is the foundation for effectively controlling wind and sand flow into the Yellow River basin.

TiNi alloys are very widely used materials for implant fabrication. When applied as rib replacement, they are required to be manufactured as combined porous-monolithic structure, ideally with a thin porous part well-adhered to its monolithic substrate. Additionally, good biocompatibility, high corrosion resistance and mechanical durability are also highly demanded. So far, all these parameters were not achieved in one material, which is why active search in the field is still underway. In the present work, we prepared new porous-monolithic TiNi materials by sintering a TiNi powder (0-100 µm) on monolithic TiNi plates followed by surface modification with high-current pulsed electron beam. The obtained materials were evaluated by a set of surface and phase analysis methods, after which their corrosion resistance and biocompatibility (hemolysis, cytotoxicity, and cell viability) were evaluated. Finally, cell growth tests were conducted. In comparison with flat TiNi monolith, the newly-developed materials were found to have better corrosion resistance, also demonstrating good biocompatibility and potential for cell growth on their surface. Thus, the newly-developed porous-on-monolith TiNi materials with different surface porosity and morphology show promise as potential new-generation implants for rib endoprostheses.

In this paper, we consider a reconfigurable intelligent surface (RIS)-assisted integrated satellite-high altitude platform-terrestrial networks (IS-HAP-TNs) that can improve network performance by exploiting HAP's stability and RIS's reflection. Specifically, the reflector RIS is installed on the side of HAP to reflect signals from the multiple ground user equipments (UEs) to the satellite. To aim at maximising system sum rate, we jointly optimize the transmit beamforming matrix at the ground UEs and RIS phase shift matrix. Due to the limitation of the unit modulus of the RIS reflective elements constraint, the combinatorial optimization problem is difficult to tackle it effectively by traditional solving methods. Based on this, this paper studies deep reinforcement learning (DRL) algorithm to achieve online decision making for this joint optimization problem. In addition, it is verified through simulation experiments that the proposed DRL algorithm outperforms the standard scheme in terms of system performance and execution time, and higher computing speed, making real-time decision making truly feasible。