A field experiment was conducted for determination of crop coefficient (KC) and water stress coefficient (Ks) for wheat crop under different salinity levels, during 2015-16. Complete randomized block design of five treatments were considered, i.e., 0.51 dS/m (fresh water) as a control treatment and other four saline water treatments (4, 6, 8 and 10 dS/m), for S1, S2, S3 and S4 with three replications. The results revealed that the water consumed by plants during the different crop growth stages follows the order of FW>S1>S2>S3>S4 salinity levels. According to the obtained results, the calculated values of crop coefficients significantly differed from those suggested by FAO No.56 for the crops. The Ks values clearly differ from one stage to another because the salt stress causes both osmotic stress, due to a decrease in the soil water potential, and ionic stress which the average values of water stress coefficient (Ks) follows this order; FW(1.0)=S1(1.0)>S2(1.0)>S3(0.93)>S4(0.82). Overall, it was found the differences are attributed primarily to specific cultivar, the changes in local climatic conditions and seasonal differences in crop growth patterns. Thus, further studies are essential to determine the crop coefficient values under different variables, to make the best management practice (BMP) in agriculture.

In the presented work, on the example of thin-walled specimens made by selective laser melting technology from AlSi10Mg subjected to preliminary heat treatment, it is shown that there is a critical point of transition from the elastic-plastic region of the engineering stress-strain diagram to the yield and fracture stresses. It was found that the critical point has a strong statistically significant correlation (0.83 by Spearman and 0.93 by Pearson) with the strain hardening coeffi-cient calculated in the section from yield strength to fracture strength. A regression equation linking the critical transition point to the strain hardening coefficient was obtained. It is shown that with increasing plasticity of thin-walled samples obtained by selective laser melting of AlSi10Mg leads to a change in the type of stress distribution in the elastic-plastic region (the Weibull distribution changes to a normal distribution) and the contribution of the probability density of stress distribution described by the Cauchy distribution with a mode near the fracture stress to the full probability density of fracture increases.

This study uses a mass-spring-damping system to simulate the repeated strain of liquefaction cyclic triaxial tests. The two results are compared in this paper to understand the feasibility of the mass-spring-damping system developed in this paper and the feasibility of future research on this related topic and development potential. The main factors affecting this mode's repeated strain are the spring coefficient k and the external force Q0. The spring coefficient has an inverse relationship but does not increase in multiples. The external force has a direct proportional relationship but does not increase the result- a non-multiple increase. When the pore water pressure of the liquefied cyclic triaxial test specimen rises, it will cause the specimen to liquefy, decreasing effective stress, shear modulus G, and damping ratio D, causing an increase in strain. The shear modulus and damping ratio are related to the spring coefficients k and c. Both are variables that change with time. This article takes an original thin-tube specimen at point A in the Yunlin area in Taiwan as a testing example. Through Mathematica software, it can be obtained that the mass m=1kg, the spring coefficient k=244e-0.1t kgf/cm, and the damping coefficient c=0.739e-0.257t kgf-s/cm and external force Q0=10.1sin2πt kg; Finally, this study selected the original thin-tube specimens from four locations in the Yunlin area, and simulated the repeated strain amount of the cyclic triaxial test specimens through a spring-damping system. The results show that the spring-damping system is feasible for simulated cyclic triaxial tests because the model is simple and the parameters are easy to understand and obtain, which also shows the extensibility of this model. Preliminary results of the research show that this model can further simulate the repeated strain obtained by cyclic triaxial tests without considering the increased trend in pore water pressure and the decrease in effective stress during cyclic loading.

The objectives of the study were to determine the spatial rate of CO₂ flux (Net Ecosystem Exchange) and soil moisture in a wetland ecosystem applying Sentinel-1 IW (Interferometric Wide) data of VH (Vertical Transmit/Horizontal Receive—cross polarization) and VV (Vertical Transmit/Vertical Receive—like polarization) polarization. In-situ measurements of carbon flux, soil moisture, and LAI (Leaf Area Index) were carried out over the Biebrza Wetland in north-eastern Poland. The impact of soil moisture and LAI on backscattering coefficient (σ°) calculated from Sentinel-1 data showed that LAI dominates the influence on σ° when soil moisture is low. The models for soil moisture have been derived for wetland vegetation habitat types applying VH polarization (R² = 0.70 to 0.76). The vegetation habitats: reeds, sedge-moss, sedges, grass-herbs, and grass were classified using combined one Landsat 8 OLI (Operational Land Imager) and three TerraSAR-X (TSX) ScanSAR VV data. The model for the assessment of Net Ecosystem Exchange (NEE) has been developed based on the assumption that soil moisture and biomass represented by LAI have an influence on it. The σ° VH and σ° VV describe soil moisture and LAI, and have been the input to the NEE model. The model, created for classified habitats, is as follows: NEE = f (σ° Sentinel-1 VH, σ° Sentinel-1 VV). Reasonably good predictions of NEE have been achieved for classified habitats (R² = 0.51 to 0.58). The developed model has been used for mapping spatial and temporal distribution of NEE over Biebrza wetland habitat types. Eventually, emissions of CO₂ to the atmosphere (NEE positive) has been noted when soil moisture (SM) and biomass were low. This study demonstrates the importance of the capability of Sentinel-1 microwave data to calculate soil moisture and estimate NEE with all-weather acquisition conditions, offering an important advantage for frequent wetlands monitoring.

Due to the long duration and high cost of traditional pumping tests, the response of well water level to seismic wave, earth tide, and barometric pressure provides a feasible method for determining continuous changes in aquifer hydraulic parameters. Aiming at the problem that the response phase shift of well BB water level to tidal tide M2 is greater than that of tide O1, this paper preferentially calculated the time series changes of S, Be, n and BKu based on the response mechanism of well water level to barometric pressure and earth tide and with the help of smooth moving method. Then by using the mixed flow model, the variation of transmissivity and leakage coefficient over time were simultaneously obtained, and the evolution process and characteristics of aquifer parameters near well BB caused by the Wenchuan earthquake were ultimately discussed. The calculation results are basically consistent with the previous pumping test, and have been verified and compared by using other scholars' methods. This solving process avoids the problems such as excessive dependence on initial values, multiple solutions, and unstable tide O1, which has a promoting effect on the study of the impact of seismic activity on aquifer systems.

The various methods used to choose the profile shift coefficients, primarily the so-called equalizations, were based on assumed advantages without physical evidence proving them. In this paper a new calculation method is presented for determining profile shift coefficient. The procedure gives the pair of values ​​of the profile shift coefficients, in which case, under the given load, the resulting bending stress will be of the lowest possible value.

Clustering coefficient measures are key complex network analysis tools. We examine local and global clustering coefficient measures with respect to the lexicographic graph product. As a preliminary condition, we analyze the $K_3$ subgraph structure focused on vertex inclusion with respect to the product graph. From this structure, we determine both the clustering coefficient for the product graph vertices and the average clustering coefficient for the product graph.

Through the geometric relationships and force analysis of the main components of the panto-graph on high-speed trains, coefficients of aerodynamic forces and lift transmission between the pantograph and main components under crosswind conditions were derived. Based on the aer-odynamic forces acting on the pantograph at different crosswind speeds, wind angles, and oper-ating speeds, the aerodynamic lift of the pantograph and main components was ultimately de-termined. The results indicate that the aerodynamic lift of the pantograph is mainly distributed on the bow structure, with the aerodynamic lift of the upper frame all being negative values, while the absolute value of the aerodynamic lift of the lower arm rod is the smallest. The oper-ating speed of the pantograph and the wind angle of the crosswind have a significant impact on the aerodynamic lift of the main components, while the impact of the crosswind speed is rela-tively small. At the same operating speed of the pantograph, the lower the corresponding crosswind speed, the smaller the aerodynamic lift of the pantograph. The aerodynamic lift of the pantograph tends to decrease gradually with the increase of crosswind speed, and the impact of crosswind speed decreases gradually with the increase of pantograph operating speed. A com-prehensive relationship formula between the aerodynamic lift of the pantograph and the oper-ating speed, crosswind speed, and wind angle is obtained, and the empirical formula for the contact force of the bow net and train operating speed is modified. The research results are of great significance and value for the study and application of lift forces on pantographs under crosswind conditions.

Wood is poised to become a material of choice for future construction. When appropriately managed, it is a renewable material with unique mechanical properties. Beyond its inherent sustainability, the use of wood has a crucial role in addressing climate change concerns due a significantly lower energy consumption and emissions during manufacturing and transportation, while simultaneously acting as a carbon sink. Thus, there has been a growing demand for hardwoods for structural applications, including Castanea sativa Mill., the focal point of this investigation. Albeit in a limited capacity, Eurocode 5-2 offers friction coefficients for softwoods, but it falls short for hardwoods which it is a gap to bridge with this research. These coefficients play a critical role in numerical simulations involving friction, enabling the optimization of joints and, by extension, the overall structural integrity. Test samples were evaluated at 18% moisture content, which is typical of Service Class 2, for various orientations of timber-to-timber and timber-to-steel friction. Considering previous friction coefficients at 12% moisture content, the linear variation was evaluated at an intermediate value of 15%. The results provide an experimental database for numerical simulations and highlight the influence of moisture content on the coefficients, which increase linearly along moisture percentages.

In this paper, we analyzed the influence of spin Nernst effect on quantum correlation in the layered ferrimagnetic model. In the study of three-dimensional ferrimagnets, the focus is on materials with a specific arrangement of spins, where neighboring spins are parallel and other antiparallel. The anisotropic nature of these materials means that the interactions between spins depend on their relative orientations in different directions. We analyzed the effect of magnon bands induced by the coupling parameters on entanglement negativity. The influence of the coupling parameters of the topologic phase transition on quantum entanglement is investigated as well. Numerical simulations using Lanczos algorithm and exact diagonalization for different sizes lattice are compared with the results of the spin wave theory.

In this work model of mirror elements equilibrium of the micromechanical components is developed, the behavior analysis of the mirror element of micromechanical mirrors in case changing of control voltages of electrostatic actuators is carried out, an expression for determining the maximum value of deflection voltage at which the snap-down effect will take the following form is obtained in case of the influence of the coefficient of the electrostatic rigidity of electrostatic actuators. The developed equilibrium model of mirror elements and the obtained results of modeling can be used at design of micromechanical mirrors with internal suspensions.

The work contains a detailed analysis of the electromagnetic field originating from a point source placed above the layered structure.The surface impedance of the multilayer dielectric structure was determined. Based on the boundary conditions, a method for determining the surface impedance of a layered structure with a perfectly conductive screen and or a magnetic screen is presented. The resonance conditions and the conditions for the excitation of surface waves are derived. The integral expression defining the generalized impedance was analyzed with a view to adapting it to numerical implementation. This allowed the development of a computer program based on which calculations were made of the effect of excitation of waves on multilayer dielectric substrates.

Key findings include the modelling of the material behavior when ZnAl15% wires were subjected to the tensile test at different speeds, with strain rate sensitivity coefficient m = 0.0128, demonstrating that this type of alloy is especially sensitive to the strain rate. Besides, the optimal friction coefficient (µ) for the drawing process of this material was experimentally identified as µ = 0.28, the ideal drawing die angle was determined to be 2α = 10°, and the alloy's deformability limit has been established by a reduction ratio r ≤ 22.5%, that indicates good plastic deformation capacity. The experimental results confirmed that the proposed models are feasible for the design and optimization of industrial processes to improve the efficiency and quality of ZnAl15% alloy wire production.

We deal with Ulam stability of second order periodic linear differential equations with periodic damping. Necessary and sufficient condition for the Ulam stability of second order periodic linear differential equations is obtained by giving an Ulam stability theorem and an Ulam instability theorem. These results extend the conclusions in relevant literature. In addition, for the situation of constant coefficients, the minimum Ulam constant is given.

This study investigated the magnitude and direction of inter-limb asymmetry in 21 professional female sepak takraw players across several task-specific tests. Five inter-limb asymmetry assessments were employed: unilateral countermovement jump (Uni-CMJ), bilateral countermovement jump (Bi-CMJ), single leg hop (SLH), triple hop test (THOP), and isokinetic concentric peak torque of the knee flexors and extensors at 60 deg/sec-1, 120 deg/sec-1 and 180 deg/sec-1 angular velocities. A “true” inter-limb asymmetry was only observed for Uni-CMJ jump height (16.62%) and THOP distance (6.09%). Kappa coefficients demonstrated fair agreement in the direction of asymmetry between the Uni-CMJ and Bi-CMJ tests for jump height (Kappa = 26.67), but only slight agreement for peak force (Kappa = 0.11), propulsive impulse (Kappa = -0.12) and eccentric impulse (Kappa = -0.14), respectively. Fair agreement was observed between the SLH and THOP (Kappa = 0.32). Slight to moderate agreement was found for concentric peak torque across angular velocities for the knee extensors (Kappa = 0.08 to 0.48) while fair to nearly perfect agreement was noted for the knee flexors (Kappa = 0.31 to 1). The Uni-CMJ and THOP are most sensitive to detect between-limb asymmetries in female sepak takraw players. However, given the inconsistency in asymmetry direction across tests, monitoring asymmetry direction is crucial for conditioning.

The dust originating from the extinct lake of the Aral Sea poses a considerable threat to the sur-rounding communities and ecosystems. The accurate location of these wind erosion areas is an essential prerequisite for controlling sand and dust activity. However, few relevant indicators re-ported in the current study can accurately describe and measure wind erosion intensity. A novel wind erosion intensity (WEI) of a resolution unit was defined in this paper based on the deformation due to the wind erosion in this resolution unit. We also derived the relationship between WEI and soil InSAR temporal decorrelation (ITD). The ITD is usually caused by the surface change over time, which is very suitable for describing wind erosion. However, within one resolution unit, the ITD signal usually includes soil and vegetation contributions, and few studies are referred to this. Therefore, we proposed an ITD decomposition model (ITDDM) to decompose the ITD signal of a resolution unit. The least-squares method (LSM) based on singular value decomposition (SVD) is used to estimate the ITD of soil (SITD) within a resolution unit. We verified the results qualitatively by the landscape photos, which can reflect the actual conditions of the soil. At last, the WEI of the Aral Sea from June 23, 2020, to July 05, 2020, was mapped. The results confirmed that (1) Based on the ITDDM model, the SITD can be accurately estimated by the LSM method, (2) the Aral Sea is experiencing severe wind erosion, and (3) The middle, northeast, and southeast bare areas of the South Aral Sea are where salt dust storms may occur.

NiV2O6 thin films were grown on glass slides with varying thicknesses using the nebulizer spray pyrolysis. The impact of thickness on the thin films' optical, structural, morphological, and electrical characteristics was systematically investigated. The X-ray diffraction and micro-Raman analysis confirmed the formation of the triclinic NiV2O6 system. Surface morphology and roughness variations in the as-deposited NiV2O6 films were studied using scanning electron microscopy (SEM) and a profilometer. Optical properties, including optical band gap (Eg), extinction coefficient (k), absorption coefficient (α), and refractive index (n), were determined through optical reflectance and transmittance measurements. The optical energy gap of the as-deposited NiV2O6 films decreased from 2.3 eV to 1.9 eV with increased layer thickness. Furthermore, the photo-detectivity of the films demonstrated an enhancement corresponding to the prolonged spray time. The sensitivity values obtained for visible irradiation are 328, 511, and 433 for samples S1, S2, and S3, respectively. The obtained results are imputed to the specific porous microstructure.

This study tries to focusing on applying information communication technology for economic importance of Mid Oil Company (MDOC), which is among contemporary oil companies in Iraq. Since ICT forms a significant aspect of achieving organizational economic objectives, most of public and private bodies seek to utilize ICT tool and techniques to improve work efficiencies. The emerging growth in ICT has made it process and service automation possible in managing organizational activities. To determine this effect of ICT on organizations, this study formulated statistical research model at MDOC through using fifteen questionnaires, which were distributed on three axes. The outcome of the questionnaire analysis revealed that there is inadequate comprehensive infrastructure to suitably support ICT within the selected organization management. In addition, it revealed that there are no ideal standards to maintain and sustain internet networks. Based on these revelations, the study presents recommendation for the adoption of ICT with the aim of minimizing cost, enhancing communication and managing infrastructure. Also recommends the need to support IT department within an organization, with essential equipment, in terms of man and machine, for better efficiency to employ the key of ICT Impact in Iraqi governmental oil companies.

The economic, social and environmental benefits generated by the use of urban public transportation infrastructure constitute a complex dynamic urban public transportation infrastructure utilization benefit system. This paper evaluates the coupling coordination among these three benefits taking four Chinese autonomous municipalities as an example. These four cities have large-scale urban public transportation infrastructures but their utilization has many serious problems. The basic function of urban public transportation infrastructure has not been fully played in these cities. Whether the different benefits of urban public transportation infrastructure have been developed in harmony or not is unclear. We analyzed the coordinated development among three benefits by constructing coupling coordination degree model and used Gini coefficient to study the difference of coordinated development among three benefits of four cities. The result shows that the levels of coordinated development among three benefits of urban public transportation infrastructure were lower in these four cities and have positive correlation with it of urban public transportation infrastructure utilization benefit. Raising the level of urban public transportation infrastructure utilization benefit is the most crucial solution of promoting the coordinated development among three benefits.

In recent years, wireless power transfer (WPT) has progressed rapidly in both theory and commercialization abroad. However, existing research into WPT coil design for low-power devices is limited. This paper investigates coil structure using printed circuit board (PCB) for magnetic resonant coupling WPT to address this gap. Specifically, the impacts of key geometric parameters on the coil quality factor and coupling coefficient are analysed through models and simulations. Equivalent PCB coils were formed for mutual inductance models, and four basic compensation circuits were analysed. The impacts of changes in coil thickness, line width, turn spacing, and number of turns on the quality factor of PCB coils were analysed with a fixed outer diameter of the coil. In this paper, to mitigate the coil offset while retaining PCB manufacturing simplicity for practical uses, a dual layer PCB coil structure is proposed. The structure optimizated PCB coil could offer remarkable improvements in the WPT system for low power electronic devices.

Evaluation ecosystem service value (ESV) is critical for “lucid waters and lush mountains are invaluable assets”. However, the ESV estimation and spatial-temporal analysis for mountainous soil erosion area is rare, e.g., Changting county, China. In this study, we developed a remote sensing driven mountainous equivalent factor (RS-MEF) method to estimate the ESV of soil erosion area in subtropical mountain. It is a hybrid of a conventional equivalent factor framework and the remote sensing techniques for mountains, and achieves several highlights of spatial adjustment using carbon sink with vegetation canopy, improvement spatial resolution, and removal topographic effect. Using the RS-MEF method, we estimated that the ESV of Changting county was about 15.80 billion CNY in 2010 and 34.83 billion CNY in 2022. Specifically, the ESV per unit area of major soil erosion area (MSEA) in the county was less than that of non-major soil erosion area (n-MSEA), however, the ESV growth rate of MSEA from 2010 to 2022 was faster than that of n-MSEA. Therefore, the ESV gap between two areas was shortened from 28.99% in 2010 to 15.83% in 2022. Topographic gradient effect analysis illustrates that the area with high elevation and small slope is one control focus in the next step. Our study indicates that the ecological restoration in the county has made great achievements in the ESV perspective, with low ESV area shrank evidently in MSEA; and the achieved knowledge of the ESV growth and inherent factors is valuable and instructive for the next soil and water conservation.

This study examines the relationship between Gross Domestic Product (GDP) and income inequality in Greece across three key periods: the pre-crisis period (2003-2008), the crisis and memoranda period (2009-2014), and the post-crisis period (2015-2020). Using data from the World Bank Open Data database, the study employs correlation analysis, and linear regression models to analyze how economic changes influence income distribution. The findings reveal that during the pre-crisis period, economic growth was moderately correlated with increasing inequality, although this relationship was not statistically significant, indicating uneven distribution of growth benefits. In the crisis period, a strong and statistically significant negative relationship between GDP and the Gini coefficient was identified, highlighting the sharp rise in inequality as the economy contracted due to austerity measures. In the post-crisis period, the relationship between GDP and inequality weakened, showing a statistically insignificant correlation, suggesting that economic recovery alone did not significantly reduce inequality. The study concludes that economic growth is insufficient to address income inequality without targeted policy interventions, particularly during periods of crisis. These findings underscore the importance of comprehensive social policies to mitigate inequality and suggest areas for future research on the impact of specific interventions on income distribution.

A two-year experiment was conducted with a local maize hybrid under full irrigation (F), deficit irrigation (D) and rainfed conditions (R) to estimate maize evapotranspiration in Bosnia and Herzegovina. Three approaches (Allen & Pereira (A&P), SIMDualKc (SD), and Vegetation Index (VI)) were used to estimate the actual crop coefficient (Kc act), actual basal crop coefficient (Kcb act), and actual crop evapotranspiration (ETc act) were applied with the dual crop coefficient method and remote sensing (RS) data. While Kcb act from all approaches matched FAO56 tabulated values, SD showed differences, in comparison to A&P, of up to 0.24 in D and R conditions, especially in initial and mid-season stages. VI demonstrated very good performance in all treatments. In F, the obtained Kc act for all approaches during the initial and end stages were higher than the tabulated values, ranging from 0.71-0.87 for Kc ini act and from 0.80-1.06 for Kc end act, while the mid-season period showed very good agreement with the literature. Maize crop evapotranspiration range is 769-813 mm, 480-752 mm, and 332-618 mm for F, D and R, respectively. The results confirmed the suitability of both approaches (SD and VI) to estimate maize crop evapotranspiration under F, with the VI approach demonstrating an advantage in calculating Kcb act, Kc act, and ETc act values under water stress conditions. The 67.6% increase in grain yields with irrigation emphasizes the need to transition from rainfed to irrigation-dependent agriculture, even for drought-resistant crops like maize.

This paper presents a statistical approach to identify the underlying roughness characteristics in synthetic aperture radar (SAR) intensity data. The physical modeling of this kind of data allows the use of the Gamma distribution in the presence of fully-developed speckle, i.e., when there are infinitely many independent backscatterers per resolution cell, and none dominates the return. Such areas are often called ``homogeneous'' or ``textureless'' regions. The GI0 distribution is also a widely accepted law for heterogeneous and extremely heterogeneous regions, i.e., areas where the fully-developed speckle hypotheses do not hold. We propose three test statistics to distinguish between homogeneous and inhomogeneous regions, i.e., between gamma and GI0 distributed data, both with a known number of looks. The first test statistic uses a bootstrapped non-parametric estimator of Shannon entropy, providing a robust assessment in uncertain distributional assumptions. The second test uses the classical coefficient of variation (CV). The third test uses an alternative form of estimating the CV based on the ratio of the mean absolute deviation from the median to the median. We apply our test statistic to create maps of \(p\)-values for the homogeneity hypothesis. Finally, we show that our proposal, the entropy-based test, outperforms existing methods, such as the classical CV and its alternative variant, in identifying heterogeneity when applied to both simulated and actual data.

The Polynomial coefficient function, from the complex hyperspace Cⁿ in itself, is the function Fⁿ that provides the coefficients of the polynomial (x - a₁)(x - a₂)... (x-a_n). A proof of the fundamental theorem of algebra is given where the surjectivity of this function is obtained from a Recurrent Coefficient Equation.

Let $\mathcal{\mathcal{S}}_{\cos}^{\ast}$ denote the class of normalized analytic functions $f$ in the open unit disk $\mathbb{D}$ satisfying the subordination $\dfrac{zf^{\prime}(z)}{f(z)}\prec\cos z$. In the second section of this article we find the sharp upper bounds for the initial coefficients $a_{3}$, $a_{4}$ and $a_{5}$ and the sharp upper bound for module of the Hankel determinant $|H_{2,3}(f)|$ for the functions from the class $\mathcal{S}_{\cos}^{\ast}$. The first result of the next section deals with the sharp upper bounds of the logarithmic coefficients $\gamma_{3}$ and $\gamma_{4}$ and we found in addition the sharp upper bound for $\left|H_{2,2}\left(F_{f}/2\right)\right|$. For obtaining these results we used the very useful and appropriate Lemma 2.4 of N.E. Cho et al. [Filomat 34(6) (2020), 2061--2072], and the technique for finding the maximum value of a three variable function on a closed cuboid. All the maximum found values were checked by using MAPLE\texttrademark{} computare software, and we also found the extremal functions in each cases. All of our present results are the best ones and give sharp versions of those recently published in [Hacet. J. Math. Stat. 52, 596--618, 2023].

Smart City has emerged as the mainstream paradigm for urban governance innovation, sustainable development, and strategy upgrades, which is drawing attention from scholars worldwide. However, current frameworks for Smart City assessment remain incomplete and simplistic. In is paper, 30 national or provincial capitals in China were selected and we designed a tri-dimensional SPI model—Social, Physical, and Information Space—for smart city spatial development assessment. Utilizing methods such as entropy weighting, coupled coordination degree models, and the Dagum Gini coefficient, this study assesses the spatial development and coupled coordination of 30 cities from 2011 to 2019. Finally, by means of BP neural networks, the study examines the contribution of each indicator to the spatial coupled coordination. The results indicated that with a narrowing disparity in development speeds among different regions, the spatial coupled coordination development level of smart capitals in China has steadily increased, presenting a pattern of staggered distribution. Moreover, the IS subsystem plays the most significant role in coupled coordination. The significance of this research lies in its tri-dimensional spatial perspective of the spatial development and coupled coordination differences of the Smart City, providing evidence-based support for the regional layout and optimization in China.

In the context of the Korean building structure standard KDS2022, wind loads can be readily calculated in terms of the along-wind, across-wind, and torsional components, based on a single wind direction. However, this approach falls short in accurately and safely evaluating the impact of winds from various directions. Therefore, in this study, we developed a Wind Load Calculation Program (WCP) capable of predicting wind loads with relative precision during the preliminary design phase. First, wind tunnel tests were conducted to identify the essential factors necessary for calculating wind loads and the variables influencing these factors. The building shape considered was a square, and the wind force coefficients and power spectral density were measured by combining 4 ground roughness values, 11 side ratios (), 4 aspect ratios (), and wind directions ranging from 0° to 90°. Subsequently, a generalized formulation was devised to facilitate wind load calculations across diverse conditions and a method for calculating load combination coefficients, considering response correlation and load simultaneity, was presented. Finally, the wind loads obtained from the wind tunnel tests were compared with those predicted by the WCP using an actual project model.

Agricultural land in China represents a major source of nitrous oxide emissions, and as population growth and technological advancements drive agricultural intensification, these emissions are projected to increase. A thorough understanding of historical trends and future dynamics of these emissions is critical for formulating effective mitigation strategies and advancing progress toward the Sustainable Development Goals. This study quantifies nitrous oxide emissions across 31 provinces in China from 2000 to 2021, employing the IPCC coefficient method alongside China’s provincial greenhouse gas inventory guidelines. The spatiotemporal evolution of emission intensities is examined, with the STIRPAT model employed to assess the influence of population, technological development, economic growth, and energy structure. The findings confirm that agricultural land remains the primary source of nitrous oxide emissions, with significantly higher levels observed in eastern coastal regions compared to western inland areas. Implementing targeted mitigation strategies, such as enhanced agricultural and manure management practices and region-specific interventions, is imperative to effectively curb the rising emission trends.

Shear dynamics simulation under extreme pressure was used to optimise the composition of ester-based lubricant base oil and extreme pressure additives. As a result, the ester-based lubricant in the weak-gel drilling fluid achieves reduction and increases the efficiency in drilling construction, and the field operation efficiency improves. The results of base oil lubrication simulation show that three base oils, namely, methyl oleate, ethyl oleate and butyl oleate, can be stably adsorbed on the surface layer of the shear surface. Methyl oleate has the lowest system temperature after shear stabilisation and has a high load-bearing capacity. The shear stress of methyl oleate decreases by changing the initial shear temperature and speed. It increases by 6.36 MPa when the speed increases from 10 m/s to 30 m/s. At this time, the shear stress of butyl oleate increases by 10.11 MPa. The results of the four-ball friction experiments show that the radius of the abrasion spot of methyl oleate is 179.83 μm, which is smaller than that of the other two base oils. Moreover, the friction coefficient of methyl oleate is 0.0018, which is approximately 1/3 of that of butyl oleate. Methyl oleate has better lubrication efficiency. The shear simulation results are consistent with the experimental results. The simulation can be used for the molecular design of lubricant materials. The oleic acid amide–containing amine group and the glyceride oleic–containing hydroxyl group were selected as the extreme pressure functional components for shear simulation. Results show that the shear stress of oleic acid amide is much lower than that of oleic acid glyceride when the initial shear temperature and speed change. The extreme pressure lubrication component–containing amine group is better than the extreme pressure lubrication material–containing hydroxyl group. The effects of different oleamide contents in the two-component mixtures on the lubricating properties were investigated through shear simulation, with methyl oleate as the base oil and oleamide as the extreme pressure functional component. The simulation results show that the lubricant has the optimal shear stress when 10% oleamide is added to the lubricant. The base properties of the lubricant were tested using a mixture of 90% methyl oleate and 10% oleamide, formulated as a lubricant. Results show that the friction coefficient can be reduced to 0.03 when 0.5% of the lubricant is added to the base mud. Moreover, the lubricant film formed shows high strength. Then, 1% lubricant was added to the weak-gel drilling fluid to evaluate the effect of the lubricant on the gel structure of the drilling fluid. Results show that adding lubricant does not affect the rheological properties of the drilling fluid. The gel structure of the system also remains stable even after 7 days of continuous ageing. The results of the field experiments in Hua3-01 well show that adding 1% ester-based lubricant to the field drilling fluid reduces the drilling friction by 33%. Thus, the efficiency of directional side drilling can be effectively improved, complicated accidents, such as poor starting and stopping of drilling and stuck jamming, can be avoided, and the goals of reducing quantity and increasing efficiency can be completed.

The state of the grinding wheel in the grinding process directly affects the surface quality of the workpiece. The monitoring of the wear state of the grinding wheel can effectively identify the wear information of the grinding wheel and timely and effectively repair the grinding wheel. In this paper, a multi-sensor fusion precision grinding wheel wear intelligent monitoring system is established for typical difficult-to-machine aerospace material titanium alloy, and a multi-eigenvalue fusion algorithm based on improved support vector machine (SVM) is proposed. The extracted sound emission signal wavelet packet decomposition coefficient mean square value, force signal grinding force ratio, and vibration signal effective value are used as the input of the improved support vector machine, and the identification strategy is adjusted by the entropy weight evaluation method. The results show that the monitoring system established in this paper can effectively identify the wear state of the grinding wheel, and the monitoring accuracy can reach more than 92%.

The CT (computed tomography) scanner has been used for many years now not only for medical measurements, but also in many industries, mostly for tasks such as defectoscopy, measuring sheet thickness, checking the joining of materials, but also for measuring the geometry of individual components. It is a good complement to coordinate contact and non-contact measurements for intra-structural measurements and inaccessible places. The variety of materials, however, makes it very difficult to select individual CT parameters. In this paper, a curve for selecting the maximum and minimum voltage of the lamp depending on the density of a given material has been determined and an interpolation polynomial (1d third-degree polynomial) has been used, by defining 3rd-degree glued functions (cubic spline) to determine intermediate voltage values to a given material density, so as to determine full data ranges. This approach will facilitate the work of selecting scanning parameters for nondestructive testing, as this is a difficult process and sometimes consumes half of the measurement time. Work is underway at the Accredited Coordinate Metrology Laboratory to develop a multi-criteria matrix for selecting CT measurement parameters for measurement accuracy.

Water pollution is the main cause of global ecological degradation and seriously affects people's water supply. In order to respond to the water environmental protection policy and provide management departments with a basis for refining water quality, this paper used the environmental Gini coefficient (EGC) method based on four indicators such as water environmental capacity, population, land area, and gross domestic production (GDP) to represent social factors, economic factors, and environmental factors, respectively. After the optimization, for COD, the EGC based on the land area was 0.30, EGC based on population was 0.21, EGC based on environment capacity was 0.02, and the EGC based on GDP was 0.45, and the sum of EGC was 0.962. From this result, we observed that the change in the Gini coefficient of each indicator was not very big. Hence, the most significant change in the Gini coefficient was that of GDP, with a higher rate than other criteria. Then, the COD, AND, and TP discharge allocation model was constructed to obtain the total allocated discharge permit in Lushui Basin. The results found that the total discharge permit allocation of COD, AN, and TP to the Lushui basin were 51483.304 tons/year, 843.119 tons/year, and 340.926 tons/year, respectively. Based on the GIS spatial analysis technology, the distribution of unfair factors that cause pollution inequity was investigated. Finally, the reduction measures were proposed to implement environmental supervision and strengthen water environment management strictly.

Imbalanced classes can cause machine learning models to classify positive class instances poorly, and the models require hyperparameter sets to optimal values. This study aims to develop random forest (RF) and support vector machine (SVM) models that use the optimal hyperparameters obtained through 5-fold cross-validation data. Both models were trained using optimal hyperparameter pairs that fit two data scenarios, the original and oversampling training sets, to produce the benchmark and best models. The model's performance was evaluated using six metrics, including training and testing data. The acquired optimal RF hyperparameter pair was (500, 10) for the minimum number of instances and tree depth level. In contrast, the acquired optimal SVM hyperparameter pair was (0.001, 500) for the gamma and constant values. The benchmark model performed approximately 98% on Accuracy, Precision, Recall, and F1 score metrics but failed to deliver any performance on Mathew's Correlation Coefficient (MC) and Area under Curve (AUC) metrics. The best RF and SVM perform less than both benchmark models in four famous metrics. Both best models have performance improvements of approximately 6% and 11% for the MCC and AUC metrics, respectively. The best RF performance was slightly better than the best SVM performance.

GR4J (Genie Rural a 4 parame`tres Journalier) is a rainfall-runoff model widely used to modelling rainfall into discharge. In this model, the input data used are daily rainfall and evapotranspiration data, calibrated using daily observed discharge data. This model seeks the optimum parameter value that produces the minimum deviation or error. The Nash-Sutcliffe Coefficient and Relative Volume Error (RVE) are used to estimate the errors that occur. One of the modelling parameters, namely X4 (peak time), has a value that does not match the observed hydrograph peak time (Tp). For this reason, it is necessary to adjust the modelling equation so that the unit hydrograph of the model appropriately in terms of value and shape with observed unit hydrograph. This study examines ten watersheds in Java Island so that it is expected to represent catchment conditions in tropical areas and developing countries. A relationship was obtained between the difference peak time from modelling (X4) and observed Tp. Adjustments Formula can be made to the general GR4J modelling equation for unit hydrograph in Java Island watersheds.

The diffusion coefficient--a measure of dissipation, and the entropy--a measure of fluctuation are found to be intimately correlated in many physical systems. Unlike the fluctuation dissipation theorem in linear response theory, the correlation is often strongly non-linear. To understand this complex dependence, we consider the classical Brownian diffusion in this work. Under certain rational assumption, i.e. in the bi-component fluid mixture, the mass of the Brownian particle $M$ is far greater than that of the bath molecule $m$, we can adopt the weakly couple limit. Only considering the first-order approximation of the mass ratio $m/M$, we obtain a linear motion equation in the reference frame of the observer as a Brownian particle. Based on this equivalent equation, we get the Hamiltonian at equilibrium. Finally, using canonical ensemble method, we define a new entropy that is similar to the Kolmogorov-Sinai entropy. Further, we present an analytic expression of the relationship between the diffusion coefficient $D$ and the entropy $S$ in the thermal equilibrium, that is to say, $D =\frac{\hbar}{eM} \exp{[S/(k_Bd)]}$, where $d$ is the dimension of the space, $k_B$ the Boltzmann constant, $\hbar $ the reduced Planck constant and $e$ the Euler number. This kind of scaling relation has been well-known and well-tested since the similar one for single component is firstly derived by Rosenfeld with the expansion of volume ratio.

Competition between cotton, winter, and summer crops is the greatest obstacle for plant breeders in Egypt. Breeders are thus seeking early maturing, high-yielding cultivars that are suited for planting following winter crops. This study was conducted during the 2016 and 2018 growing seasons at the Sakha agriculture research station, Egypt's agricultural research facility. This research used breeding material from the F2, F3, and F4 generations that resulted from crossing Giza 94 and Uzbekistan. During the 2016 growing season, the F2 population was cultivated, and the top 5% of the F2 population (75 plants) were chosen based on the selection criteria. In the summer of 2017, the F3 families were cultivated, and 5% of the superior F3 families were chosen to become the F4 fam-ilies, which were planted in the summer of 2018 at the single plant and bulk studies in a randomised full block design with three replications. The average performance of the characteristics boll weight, seed cotton yield, lint percentage, and lint index increased as generations passed from F2 to F4. In the meanwhile, the characteristic value of the first flower to open decreased, showing the accu-mulation of advantageous alleles. For all examined characteristics, the phenotypic coefficient of variance was greater than the genotypic coefficient of variation. In addition, the data demonstrated that heritability in a broad sense was greater in F4 populations than in F3 and F2 populations. With a few exceptions, the phenotypic and genotypic associations for all investigated characteristics were positive and very significant. According to the data, initial opening flowering and boll weight had a substantial impact on seed cotton output per feddan. In general, five superior families No. 9, 13, 18, 19, and 20 were chosen from the F4 population, which were more significant for yield and yield component than the commercial variety, and these genotypes may be promising for the breeding programme to develop new genotypes with superior yield.

The efficiency of cold sheet and strip rolling of steels and non-ferrous metals in the main depends on the quality of the technological lubricant and its cost. In this regard, it is important to develop new compositions of effective metal-working coolants (MWC) having low cost and providing the maximum reduction in the friction coefficient. We developed and tested the new compositions of the MWC on basis of chicken fat, and mono- and diglycerides and their esters of boric acid synthesized from the wastes of sunflower oil production. The MWC were tested in DSEA on laboratory rolling mill 100x100 with a roll diameter of 260 mm during steel 08Kp rolling. The efficiency of the coolants was determined by the factor of metal stretch forming λ and the coefficient of friction μ in the deformation zone which was found by forward slip method. We found the metal-working coolant with 100 % concentration of boric acid esters of mono- and diglycerides is the most effective in steel rolling. Thus the new MWC on basis of boric acid esters of mono- and diglycerides synthesized from the wastes of sunflower oil production can be recommended for use in rolling of structural steels on account of availability, high efficiency, and a low cost.

The paper proposes an approach to solving the inverse epidemiological problem, written in terms of the “mean field” theory. Finding the coefficients of the epidemiological SIR mean field model is reduced to solving an optimization problem, for the solution of which only zero-order methods can be used. The Nelder-Mead method was chosen as such a method. The algorithm for solution of the inverse coefficient problem is proposed. Computational experiments were carried out to compare the obtained solutions with respect to synthetic and real data. The results of computational experiments have shown the efficiency of this approach. Ways to further improve the approach have also been determined.

Hyperspectral imaging, a rapidly evolving technique, furnishes exhaustive information on Earth's surface reflectance over an extensive spectrum of wavelengths. We have developed a more precise method for analyzing spectral data by meticulously selecting plant leaf pixels and employing a relative reference approach. This enhanced technique correlates camera pixel values with light intensity, bypassing the need for complex equations and thereby providing clearer insights into vegetation vitality. The findings of this study not only enhance the precision of hyperspectral imaging but also bolster our capability for ecological monitoring and understanding environmental health. A novel algorithm based on the red-edge slope was established to classify images, exploiting the spectral reflectance data gleaned from the hyperspectral Liquid Crystal Tunable Filter (LCTF) camera. Compared with conventional SVM and K-means algorithms, our novel algorithm demonstrated commendable performance, achieving an overall accuracy of 90% with a Kappa Coefficient of 0.86. This comparison highlights the novel algorithm's relative strength and potential for large-scale satellite and drone imagery analysis applications. The advancements facilitated by this research are instrumental in ecological assessments, conservation efforts, and resource management strategies, signaling a leap forward in the era of environmental monitoring and analysis.

Next generation in-to-out-of body biomedical applications have adopted optical wireless communications (OWCs). However, by delving into the published literature, a gap is recognised in modeling the in-to-out-of channel, since most published contributions neglect the particularities of different type of tissues. Towards this direction, in this paper we present a novel pathloss and scattering models for in-to-out-of OWC links. Specifically, we derive extract analytical expressions that accurately describe the absorption of the five main tissues’ constituents, namely fat, water, melanin, oxygenated and de-oxygenated blood. Moreover, we formulate a model for the calculation of the absorption coefficient of any generic biological tissue. Next, by incorporating the impact of scattering in the aforementioned model we formulate the complete pathloss model. The developed theoretical framework is verified by means of comparisons between the estimated pathloss and experimental measurements from independent research works. Finally, we illustrate the accuracy of the theoretical framework in estimating the optical properties of any generic tissue based on its constitution. The extracted channel model is capable of boosting the design of optimized communication protocols for a plethora of biomedical applications.

The knowledge of the optical properties of biological tissues in a wide spectral range is highly important for the development of noninvasive diagnostic or treatment procedures. The absorption coefficient is one of those properties, from which various information about tissue components can be retrieved. Using transmittance and reflectance spectral measurements acquired from ex vivo rabbit brain cortex samples, allowed to calculate its optical properties in the ultraviolet to the near infrared spectral range. Melanin and lipofuscin, the two pigments that are related to the ageing of tissues and cells were identified in the cortex absorption. By subtracting the absorption of these pigments from the absorption of the brain cortex, it was possible to evaluate the true ratios for the DNA/RNA and hemoglobin bands in the cortex – 12.33 fold (at 260 nm), 12.02 fold (at 411 nm) and 4.47 fold (at 555 nm). Due to the fact that the accumulation of melanin and lipofuscin increases with the ageing of the brain tissues and are related to the degeneration of neurons and their death, further studies should be performed to evaluate the evolution of pigment accumulation in the brain to prevent the development of Alzheimer, Parkinson and stroke pathologies in the brain.

In order to enhance the efficiency of direct absorption solar collectors, this study carried out an experimental analysis about the optical and photothermal conversion performance of Fe3O4, ATO and Fe3O4/ATO nanofluids with total concentration of 0.1wt%. According to the results of experiments, Fe3O4 nanofluid outperform ATO nanofluid in terms of optical absorption; nevertheless, at wavelengths shorter than 600 nm, it also shows significant scattering reflection. The solar-weighted absorption coefficient of Fe3O4/ATO nanofluid rose from 0.863 (mFe3O4mTotal= 0.2) to 0.932 (mFe3O4mTotal= 0.8) when the optical path length increased from 0.01 m to 0.06 m. Additionally, the photothermal conversion efficiency of Fe3O4/ATO hybrid nanofluid was attained 0.932 at (mFe3O4mTotal= 0.2), above the 0.892 and 0.898 photothermal conversion efficiencies recorded for 0.1 wt% ATO and Fe3O4 nanofluids, respectively. When present together, the opposing optical characteristics of Fe3O4 and ATO boost photothermal conversion performance, which is anticipated to raise the efficiency of direct absorption solar collectors.

The experiences gathered during the past 30 years support the operational use of irrigation scheduling based on frequent multi-spectral image data. Currently, the operational use of dense time series of multispectral imagery at high spatial resolution makes monitoring of crop biophysical parameters feasible, capturing crop water use across the growing season, with suitable temporal and spatial resolutions. These achievements, and the availability of accurate forecasting of meteorological data, allow for precise predictions of crop water requirements with unprecedented spatial resolution. This information is greatly appreciated by the end users, i.e. professional farmers or decision-makers, and can be provided in an easy-to-use manner and in near-real-time by using the improvements achieved in web-GIS methodologies. This paper reviews the most operational and explored methods based on optical remote sensing for the assessment of crop water requirements, identifying strengths and weaknesses and proposing alternatives to advance towards full operational application of this methodology. In addition, we provide a general overview of the tools which facilitates co-creation and collaboration with stakeholders, paying special attention to these approaches based on web-GIS tools.

Traditional concrete pavements have poor water permeability, while the strength of pervious concrete pavements is low. To solve these problems, this study designed Innovative recycled aggregate pervious concrete (I-RAPC) with controllable water permeability and high strength by using response surface methodology, and investigated the effects of different pore parameters (number, diameter, material, distribution form, etc.) on the performance of I-RAPC. And the strength discount factor method was proposed to construct the theoretical calculation model of compressive strength and pipe pore parameters, and the calculation model of water permeability coefficient was established at the same time. The results show that the fewer the number of holes and the smaller the pipe diameter of I-RAPC, the higher its compressive strength and the smaller the water permeability coefficient. The theoretical model of compressive strength can accurately evaluate the discounting effect of the pore parameters on the compressive strength of I-RAPC, and the maximum relative error is only 7.52%, and the maximum relative error of the calculation model of water permeability coefficient is only 4.42%. I-RAPC has the advantages of high strength and permeability with controllable performance, which overcomes the problems of random distribution of pore space, uncertainty of water permeability, and strength of ordinary pervious concrete.

We study the enhancement of the elastocaloric effect in natural rubber by using forced air convection in order to favour heat extraction during the elongation stage of an stretching-unstretching cycle. Elastocaloric performance is quantified by means of the adiabatic undercooling that occurs after a fast removal of the stress, measured by infrared thermography. To ensure accurate measurements, spatial averages on thermal maps of the sample surface are performed since undercooled samples display heterogeneities caused by various factors. The influence of the stretching velocity and the air velocity is analysed. The results show that, given the fact that the stretching velocities should be high enough to improve the cooling power, there is an optimal air velocity that provides maximum adiabatic undercooling. Our experiments have also allowed us to characterise the dependence of the Newton heat transfer coefficient on the air convection velocity. We have shown that this coefficient may show an enhancement up to 600% for air velocities around 4 m/s.

Optinalysis, as a method of symmetry detection, is a new algorithm that intrametrically (within elements or variables) or intermetrically (between elements or variables) computes and compares two or more univariate or multi-clustered or multivariate sequences as a mirror-like reflection of each other (optics-like manner), hence the name is driven. Optinalysis is based by the principles of reflection and moment about a symmetrical line which detects symmetry that reflects a similarity measurement. This proposed methodology was validated in comparison with Pearson method of skewness detection, and also with some algorithms for pairewise alignment and comparison of genomic sequences (Needle, Stretcher, Water, Matcher) on EMBL-EBI website. A results comparison shows that optinalysis is more advance, more sensitive, more inferential and simple alternative approach of skewness detection and pairewise sequence comparison.

Usually in quantum optics, the theory of large- and small-scale waveguide beam splitters is the same. In this paper it is shown that the theory of the nanoscale waveguide beamsplitter has a significant difference from a similar device, but of a larger scale. It is shown that the previously known theory of the waveguide beam splitter is a particular case of the theory presented here. The wave function at the output ports of the nanoscale beam splitter is analyzed. The results obtained are sensitive to the size of the beam splitter, the coupling parameter of the two waveguides, and the degree of nonmonochromaticity of the photons entering the first and second ports of the beam splitter. The results are important for quantum technologies using a nanosized beam splitter.

Human resources are the major input of health systems therefore the equitable distribution of human resources in health care remain critical in making progress towards the goal of universal health coverage and thus to sustainable development. The purpose of this study is to evaluate the health care human resources distribution across regions of Poland between 2010 and 2017 and estimate the level of equity. This research by applying to Polish conditions will allow to fill in the gap in existing literature. Data was derived from the Knowledge Database Health and Health Care of Statistic Poland and Polish Statistical Yearbook. In purpose to examine the distribution of health resources against population size and geographic size in Poland, the Gini coefficient calculated based on the Lorenz Curve was engaged. This study has several major findings. The amount of most types of human resources – as apart from internist, obstetrics and gynecology, occupational medicine - when expressed as number of them per 10,000 population or 1 square km increased in 2017 compared to 2010. Moreover, for most types of health care human resources the level of access slightly changed during analysied period as Gini coefficients decreased. However, the geographical distribution of all types of human resources is less equitable then in case of population distribution. The most troublesome is relatively lower equity in case of oncologist, family medicine and occupational medicine and cardiologist in both population and geographical distribution. Thus this research provides some implications for policy and practice. As the main reason to establish National Health Fund (which meant the centralization of the system) in Poland was to to eliminate regional differences in access to health care, thus this research confirms that still some more corrective actions, in this field, should be undertaken.

The deterioration of soil-cement in corrosive environment leads to the reduction of strength and the increase of permeability. Effective methods of determining deteriorated layer permeability coefficient of soil-cement are currently lacking. A laboratory test method for permeability coefficient of deteriorated layer was proposed using the modified permeability coefficient testing apparatus. According to the proposed method, the permeability coefficient of deteriorated layer can be obtained after testing the permeability coefficient of the soil-cement specimen in curing room and the equivalent permeability coefficient and deterioration depth of the soil-cement specimen in corrosion environment. Taking the marine dredger fill of Jiaozhou Bay for example, the deteriorated layer permeability coefficients of soil-cements with different cement contents were tested. It turned out that the permeability of deteriorated layer increases with the increase of age. At the beginning of curing age, larger cement content leads to smaller permeability coefficient of the deteriorated layer of soil-cement. As the curing age increases, the deteriorated layer permeability coefficient of the soil-cement with larger cement content becomes larger. The evolution of the permeability coefficient of deteriorated layer with age can be formulated as the Logistic function. This study provides a support for anti-permeability designs of soil-cement structures in corrosive environment.

This paper presents a thorough investigation into the shear strength capacity of reinforced concrete deep beams, with a focus on improving predictive accuracy beyond existing code provisions. Analyzing 198 deep beams from 15 investigations, the study considers parameters such as concrete compressive strength (fc’), shear span to effective depth ratio (av/d), and reinforcement ratios (ρs, ρv, ρh ). Introducing a novel predictive model (Equation 7), the study rigorously evaluates it using nonlinear regression analysis and statistical metrics (MAE, RMSE, R2). The proposed model demonstrates a significant reduction in the coefficient of variation (COV) to 27.08%, surpassing existing codes' limitations. Comparative analyses highlight the model's robustness, revealing improved convergence of data points and minimal sensitivity to variations in key parameters. The findings suggest that the proposed model offers enhanced predictive accuracy across diverse scenarios, making it a valuable tool for structural engineers. This research contributes to advancing the understanding of shear strength in reinforced concrete deep beams, offering a reliable and versatile predictive model with implications for refining design methodologies and enhancing the safety and efficiency of structural systems.

The aim of this research was to analyze the impact of implemented erosion control works (ECW) on soil erosion intensity in the watershed of the Ćelije reservoir (Rasina River) in the period between 1968 and 2022. The Erosion Potential Method was used to calculate the annual gross erosion (W), sediment transport (G), and erosion coefficient (Z) in the study area. As a result of the performed ECW there was a general decreasing trend in the intensity of soil erosion processes in the last 54 years. The specific annual gross erosion was 1189.12 m3/km-2/year-1 in 1968, while in 2022 it was 554.20 m3/km-2/year-1. The specific sediment transport was 540.18 m3/km-2/year-1 in 1968 and 253.55 m3/km-2/year-1 in 2022. Due to the changes in the intensity of erosion processes the specific annual gross erosion decreased by 634.92 m3/km-2/year-1, and the specific sediment transport by 286.63 m3/km-2/year-1. The erosion coefficient was reduced from Z=0.62 to Z= 0.35. A dependence between the slope of siltation and the natural bed slope was defined. The results show a significant correlation between erosion intensity and performed ECW, providing a basis for future watershed management and defining a strategy for soil erosion control in the Ćelije reservoir watershed.

The radiative heat transfer in arc plasma models is considered from the point of view of its description in terms of a net emission coefficient, the method of spherical harmonics in its lowest order, and the discrete ordinate method. Net emission coefficients are computed applying approximate and numerical approaches, the multi-band representation of the spectral absorption coefficient with three kinds of its averaging and two datasets. The self-consistent access to the radiative heat transfer is applied to a two-dimensional axisymmetric model of free-burning arc in argon at atmospheric pressure. The results obtained from the models employing the net emission coefficient, the method of spherical harmonics, and the discrete ordinate method are compared.

Nowadays energy saving is a topical issue due to increasing fuel costs and this aspect is amplified by more stringent emissions regulations that impact on vehicle development. A recent study conducted by the U.S. Department of Energy shows that about five percent of the U.S. energy consumption is transmitted by fluid power equipment. Nevertheless, this study also shows that the efficiency of fluid power averages 21 percent. This offers a huge opportunity to improve the current state-of-the-art of fluid power machines, in particular to improve the energy consumption of current applications. These facts dictate a continuous strive toward improvements and more efficient solutions: to accomplish this objective a strong reduction of hydraulic losses and better control strategies of the hydraulic systems are needed. In fluid power, there exist many techniques to reduce/recover energy losses of the conventional layouts, e.g. load sensing, electrohydraulic flow matching, independent metering, etc. One of the most efficient ways to analyze these different layouts and identify the best hydraulic solution is done through virtual simulations instead of prototyping, since the latter involves higher investment costs to deliver the product into the market. However, to build a fluid power machine virtual model, some problems arise relative to different aspects, for instance: loads on actuators (both linear and rotational) are not constant and pumps are driven by a real engine whose speed depends on required torque. Furthermore, it is important to achieve higher level of detail to simulate each component in the circuit: the greater detail, the better the machine behavior is portrayed, but it obviously entails heavy impact on simulation time and computational resources. Therefore, there is a need to create mathematical model of components and systems with sufficient level of detail to easily acquire all those phenomena necessary to correctly evaluate machine performance and make modifications to the fluid power component design. In this context, a hydraulic proportional valve PVG 32 by Danfoss is taken as an object of study, its performance is analyzed with suitable mathematical model and simulation is done to observe closeness of a model to the laboratory experiment.

The unique properties and morphology of liquid marbles (LMs) make them potentially useful for various applications. Non-edible hydrophobic organic polymer particles are widely used to prepare LMs. It is necessary to increase the variety of LM particles to extend their use into food and pharmaceuticals. Herein, we focus on hydrophobically modified gelatin (HMG) as a base material for the particles. The surface tension of HMG decreased as the length of alkyl chains incorporated into the gelatin and the degree of substitution (DS) of the alkyl chains increased. HMG with a surface tension of less than 37.5 mN/m (determined using equations based on the Young-Dupré equation and Kaelble-Uy theory) successfully formed LMs of water. The minimum surface tension of a liquid in which it was possible to form LMs using HMG particles was approximately 53 mN/m. We also showed that the liquid-over-solid spreading coefficient S_(L/S) is a potential new factor for predicting if particles can form LMs. The HMG particles and the new system for predicting LM formation could expand the use of LMs in food and pharmaceuticals.

The key concepts in symmetry detection and similarity, identity measures are automorphism and isomorphism respectively. Therefore, methods for symmetry detection and similarity, identity measures should be functionally bijective, inverse, and invariance under a set of mathematical operations. Nevertheless, few or no existing method is functional for these properties. In this paper, a new methodological paradigm, called optinalysis, is presented for symmetry detections, similarity, and identity measures between isoreflective or autoreflective pair of mathematical structures. The paradigm of optinalysis is the re-mapping of isoreflective or autoreflective pairs with an optical scale. Optinalysis is characterized as invariant under a set of transformations and its isoreflective polymorphism behaves on polynomial and non-polynomial models.

A number of experimental and numerical studies point out that incorporating a rotating cylinder can superiorly enhance the aerofoil performance, especially for higher velocity ratios. Yet, there have been less or no studies exploring the effects of lower velocity ratio at a higher Reynolds number. In the present study, we investigated the effects of Moving Surface Boundary-layer Control (MSBC) at lower velocity ratios (i.e. cylinder tangential velocity to free stream velocity) and higher Reynolds number on a symmetric aerofoil (e.g. NACA 0021) and an asymmetric aerofoil (e.g. NACA 23018). In particular, the aerodynamic performance with and without rotating cylinder at the leading edge of the NACA 0021 and NACA 23018 aerofoil was studied on the wind tunnel installed at Aerodynamics Laboratory. The aerofoil section was tested in the low subsonic wind tunnel, and the lift coefficient and the drag coefficient were studied for different angles of attack. The experiments were conducted for two Reynolds numbers: 200000 and 250000 corresponding to two free stream velocities: 20 m/s and 25 m/s, respectively, for six different angle of attacks (-5°, 0°, 5°, 10°, 15° and 20°). This study demonstrates that the incorporation of a leading edge rotating cylinder results in an increase of lift coefficient at lower angle of attacks (maximum around 33%) and delay in stall angle (from 10° to 15°) relative to the aerofoil without rotating cylinder.

This paper investigates the influence of different vegetation on the permeability of the shallow soil layers of slopes under rainfall infiltration. Firstly, four large slopes are filled in the outdoor natural environment, and the overburdens of the four slopes are Magnolia multiflora, Cynodon dactylon, Magnolia multiflora mixed with Cynodon dactylon, and no vegetation. Secondly, the four slopes are cultivated in the outdoor natural environment for one year. After the vegetation overburdens are matured, the field artificial rainfall test is carried out through the self-developed artificial rainfall device to monitor the water migration law inside the four slopes in real time. Finally, the unsaturated permeability coefficients of the shallow soil layers of slopes are calculated. The results show that the infiltration rate of rainwater in each overburden slope from fast to slow is Magnolia multiflora overburden slope, no vegetation slope, Cynodon dactylon overburden slope, Magnolia multiflora mixed with Cynodon dactylon overburden slope. In the early stage of rainfall, Magnolia multiflora increases the permeability coefficient of the shallow soil layer of the slope, thus weakening the anti-seepage ability of the slope, but the influence of Magnolia multiflora is not obvious in the later stage. Cynodon dactylon and Magnolia multiflora mixed with Cynodon dactylon can significantly reduce the permeability coefficient of the shallow soil layers of the slopes, thereby increasing the anti-seepage ability of the slopes, and the mixed planting of Magnolia multiflora and Cynodon dactylon can minimize the permeability coefficient of the shallow soil of the slope, resulting in the best anti-seepage effect.

We examine the impact of temperature (T) on the Seebeck coefficient S, i.e., the T dependence of S for the single-component molecular conductor Pd(dddt)_2] (dddt = 5,6-dihydro-1,4-dithiin-2,3-dithiolate) with a half-filled band, where the coefficient is obtained from a ratio of the thermal conductivity to the electrical conductivity. The conductor exhibits Dirac electrons with a nodal line, which shows the energy variation around the chemical potential and the density of states (DOS) with a minimum. Using a three-dimensional tight-binding (TB) model in the presence of both impurity and electron--phonon (e--p) scatterings, we study the Seebeck coefficient S_y for the molecular stacking and the most conducting direction. The impact of T on S_y exhibits a sign change, where S_y > 0 with a maximum at high temperatures and S_y < 0 with a minimum at low temperatures. The T dependence of S_y suggests that the contribution from the conduction (valence) band is dominant at low (high) temperatures.The result is examined using a spectral conductivity \sigma_y(\epsilon,T) as a function of the energy $\epsilon$ close to the chemical potential \mu. Further, the Seebeck coefficients for perpendicular directions (x and z) are examined, to show both S_x and S_z being positive and no sign change in contrast to S_y.

Crop coefficient (Kc), the ratio of crop evapotranspiration (ETc) to reference evapotranspiration (ETo), is used to schedule an efficient irrigation regime. This research was conducted to investigate variations of ETc and growth-stage-specific Kc in a flood-irrigated winter wheat as a forage crop from 2021 to 2023 in the Lower Rio Grande Valley of southern New Mexico, USA, and evaluate the performances of the two temperature-based ETo estimation methods of Hargreaves-Samani and Blaney-Criddle with the widely used Penman-Monteith method. Results indicated that the total ETc over the whole growth stage for flood-irrigated winter wheat was 556.4 mm on a two-year average, while the average deep percolation (DP) was 2.93 cm and 2.77 cm, accounting for 28.8% and 27.2% of applied irrigation water, respectively in the 2021-22 and 2022-23 growing seasons. The ETo over the growing season computed by Penman-Monteith, Hargreaves-Samani, and Blaney-Criddle equations were 867.0 mm, 1015.0 mm, and 856.2 mm in 2021-22, and 785.6 mm, 947.0 mm, and 800.1 mm in 2022-23, respectively. The Hargreaves-Samani method performed better than the Blaney-Criddle method with higher statistical indicators of model efficiency coefficient (CE), and smaller mean bias error (MBE), mean absolute error (MAE), and the root mean square error (RMSE) in both growing seasons. The result of a global sensitivity analysis showed that the mean temper-ature is main driving factor for estimated ETo based on Blaney-Criddle and Hargreaves-Samani, but the sensitivity percentage for Blaney-Criddle was 76.9%, which was much higher than that of 48.9% for Hargreaves-Samani, given that Blaney-Criddle method is less accurate in ETo estimation for this area especially during the hottest season from May to August. In contrast, wind speed and maximum temperature were the main driving factors for the Penman-Monteith method, with sensitivity percentages of 70.9% and 21.9%, respectively. The two-year average crop coefficient (Kc) values at the initial, mid, and late growth stage were 0.54, 1.1, and 0.54 based on Penman-Monteith, 0.51, 1.0 and 0.46 based on Blaney-Criddle, and 0.52, 1.2 and 0.56 based on Hargreaves-Samani. Results showed that the Hargreaves-Samani equation serves as an alternative tool to predict ETo when fewer meteorological variables are available. The calculated local growth-stage-specific Kc can help improve irrigation water management in this region.

In estimating the maximum and minimum index void ratios for mixtures of sand and silt, the values of several empirical constants must be determined based on the type of sand and silt involved. These empirical constants are the filling coefficient, a, and embedment coefficient, b, both of which can be determined either through lab testing or correlations. These constants are then used in equations to predict the maximum and minimum index void ratios of the sand-silt mixtures. The study reported here developed simple correlations for estimating the filling and embedment coefficients using readily obtained laboratory data. These models were found to be excellent in developing filling and embedment coefficients that accurately (R2 values typically of 0.94 or greater.) predicted values of the index void ratios for sand and silt mixtures.

The topic of modification of magnesium oxychloride cement (MOC) via specific functional additives is very much pronounced in the research of alternative building materials. This study deals with the co-doping of MOC by 1D and 2D carbon nanomaterials in order to improve its mechanical properties while using tannic acid (TA) as a surfactant. Furthermore, the effect of TA on MOC also covers the improvement of water resistance. As a filler, three size fractions of standard quartz sand are used. The proposed types of MOC-based composites show promising results considering their mechanical, macro- and microstructural, chemical, and hygric properties. The use of 1D and 2D nanoadditives and their mixture enables the improvement of the flexural strength and most of all softening coefficient, the durability parameter characterizing the resistance of the prepared materials to water. For samples immersed in water for 24 h, the compressive strength of all modified composites tested was higher than that of the reference composite. Quantitatively, the developed co-doped composite shows mechanical parameters comparable to or even better than those of commonly used Portland cement-based materials, while maintaining high environmental efficiency. This indicates its potential use as an environmentally friendly alternative to Portland cement-based products.

With the rapid development of renewable energy, accurately forecasting wind power is crucial for the stable operation of power systems and effective energy management. This paper proposes a short-term wind power forecasting method based on the Orthogonalized Maximal Information Coefficient (OMNIC) combined with an Adaptive Fractional Generalized Pareto Motion (fGPm) model. The method quantifies the influence of meteorological factors on wind power prediction and identifies the optimal set and number of influencing factors. The model accounts for long-range dependence (LRD) in time series data and constructs an uncertainty model using the properties and parameters of the fractional generalized Pareto distribution (GPD), significantly improving prediction accuracy under nonlinear conditions. The proposed approach was validated using a real dataset from a wind farm in northwest China and compared with other models such as Convolutional Neural Network-Long Short-Term Memory (CNN-LSTM) and Convolutional Neural Network-Gated Recurrent Unit (CNN-GRU). Results demonstrate that the adaptive fGPm model significantly reduces wind power forecasting errors, offering high accuracy and robustness. This method provides practical value in alleviating peak voltage and frequency regulation challenges in power systems and in promoting the integration of wind power into the grid.

This algorithm is designed to perform Discrete Fourier Transforms (DFT) to convert temporal data into spectral data. This algorithm obtains the Fourier Transforms by studying the Coefficient of Determination of a series of artificial sinusoidal functions with the temporal data, and normalizing the variance data into a high-resolution spectral representation of the time-domain data with a finite sampling rate. What is especially beneficial about this DFT algorithm is that it can produce spectral data at any user-defined resolution.

Trade of agricultural products has gained importance with the development of global trade. Cherries has a crucial place in Turkish agricultural exports. Fresh cherries are in the scope of this study. The aim of this study is to examine Turkey’s position and competitiveness in cherry trade. Trade Intensity Analysis Method which represents the course of trade flow among countries is used in the study. The study indicates that European countries which are Turkey’s tradition trade partner has a biggest trade share with Turkey and that share did not much change in years. By the way, Asia market especially China, became a game changer in cherry trade and Turkey should prepare itself for this situation.

Among the impacts of climate change in West Africa, coastal erosion is the most threatening disaster apart from floods and the increase in temperature. The southern coast of the Dakar region, as part of the most threatened coastal zones in West Africa, records the most current coastal damages in Dakar due to its coastline dynamics and low-lying area. This study was conducted in three littoral cells (Mbao, Bargny and Toubab Dialaw) and aims to investigate if there is a relationship between the coastline dynamic, topographic and slope and the contribution of the geomorphology along the southern coast of Dakar. It helps to understand better the role which plays the topography, Slope and geomorphology in coastal dynamics using remote sensing, cartographic tools and statistical methods. The Modified Normalized Different Water index (MNDWI) was employed to delineate the coastlines before computing the dynamic rate of the coastline using the Digital Shoreline Analysis System (DSAS) software. After that, Topography and Slope were determined using Digital Elevation Model (DEM). Then, the correlation between the coastline dynamic, topography and slope was analyzed through the coefficient of correlation and multiple linear regression model. High dynamic rates were noted in the littoral cells, where the topography and slope are low. In Mbao, there is a significant relationship between the coastline dynamic, topography and slope with a coefficient of correlation of about 0.63. In Bargny, the relationship is also significant, with a coefficient of 0.87. The relationship is not significant in Toubab Dialaw, where topography and Slope are high, with a coefficient of 0.15. We conclude that topography, slope and soil properties play an important role in the study area.

This document makes a comprehensive analysis of the inequality of the water market in Chile, measured by the Gini coefficient method. The situation of water rights in Chile is of particular interest because it is a completely privatized system, where rights are traded in the market and therefore water is presented as a commodity. This privatization of water in Chile occurred as part of the process of neoliberalization since the 1981 Water Code. The results of this study indicate that both the concentration and the inequality in the distribution of water rights is very high. It proposes a profound revision of applying a mercantile logic to a scarce basic resource for life such as water and exploring the importance of its role as a national good for public use.

We investigate the tunneling of quasiparticles through a potential barrier of finite height and width, in a system with a band structure consisting of a quadratic band crossing point (QBCP). We compute the results of the transmission coefficient at various incident angles, and also the conductivity and the Fano factor. We discuss the distinguishing signatures of these transport properties in comparison with other semimetals, as well as electrons in normal metals.

Different types of resonators are used to create acoustic metameterials and metasurfaces. Recent studies focused on the use of multiple resonators of dipole, quadrupole, octupole and even hexadecapole types. This paper considers the theory of an acoustic metasurface, which is a flat surface with a periodic arrangement of multiple resonators. The sound field reflected by the metasurface is determined. If the distance between the resonators is less than a half the wavelength of the incident plane wave, the far field can be described by a reflection coefficient that depends on the angle of incidence. This allows to characterize the acoustic properties of the metasurface by a homogenized boundary condition, which is a high order tangential impedance boundary condition. The tangential impedance depending on the multiple order of the resonators is introduced. In addition, we analyze sound absorption properties of these metasurfaces, which are a critical factor in determining their performance. The paper presents a theoretical model that accounts for the multiple orders of resonators and their impact on sound absorption. The maximum absorption coefficient for a diffuse sound field, as well as the optimal value for the homogenized impedance, are calculated for arbitrary multipole orders.

This paper presents a three-dimensional model of pollutant diffusion in the atmosphere. The model is based on the advection-diffusion equation taking into account pollution sources and decay processes of substances. The numerical solution of the equation is realized using the finite difference method on a three-dimensional grid. The model takes into account the spatial distribution of pollutant concentrations, the influence of wind and atmospheric diffusion. Key parameters include diffusion coefficient, wind speed components, intensity of pollution sources and decay coefficient of substances. Special attention is paid to the vertical distribution of pollutants, which allows for more accurate modeling of atmospheric processes. The presented model can be used to predict the spread of pollutants, assess the impact of different sources on air quality and develop strategies to reduce air pollution in urban and industrial areas.

This study aimed to evaluate potential posttreatment changes in ADC values within the tissue surrounding the enhancing lesion, particularly in areas not exhibiting MRI characteristics of in-volvement. Additionally, the objective was to investigate the correlation between ADC values, treatment response, and survival outcomes in individuals diagnosed with gliomas. This retrospective study included a total of 49 patients that underwent either stereotactic biopsy or maximal surgical resection. Histologically confirmed as Grade III or IV gliomas, all cases adhered to the 2016 and 2021 WHO classifications, with subsequent radio-chemotherapy administered post-surgery. Patients were divided into two groups: short and long survival group. Baseline and follow-up MRI scans were obtained on a 1.5T MRI scanner. Two ROI circles were positioned near the enhancing area, one ROI in the NAWM ipsilateral to the neoplasm and another symmetrically in the contralateral hemisphere on ADC maps. At follow-up there was a significant difference in both ipsilateral and contralateral NAWM be-tween the two groups, -0.0857 (p=0.004) and -0.0607 (p=0.037), respectively. There was a weak negative correlation between survival and ADC values in ipsilateral and contralateral NAWM at the baseline with the correlation coefficient -0.328 (p=0.02) and -0.302 (p=0.04), respectively. The correlation was stronger at the follow-up. The findings indicate that ADC values in normal appearing white matter (NAWM) may function as a prognostic biomarker in patients with diffuse gliomas.

We consider the inverse function $z=g(w)$ of a (normalized) starlike function $w=f(z)$ of order $\alpha$ on the unit disk of the complex plane with $0<\alpha<1.$ Krzy{\. z}, Libera and Z\l otkiewicz obtained sharp estimates of the second and the third coefficients of $g(w)$ in their 1979 paper. Prokhorov and Szynal gave sharp estimates of the fourth coefficient of $g(w)$ as a consequence of the solution to an extremal problem in 1981. We give a straightforward proof of the estimate of the fourth coefficient of $g(w)$ together with explicit forms of the extremal functions.

The service life of the reinforced concrete structure in the marine environment can be impaired significantly due to chloride-induced corrosion. However, how the chloride diffusion in pre-cracked concrete structures is affected by the hydrostatic pressure magnitude is poorly understood. This study experimentally examined the effect of hydrostatic pressure on the chloride diffusion in pre-cracked concrete. Cracks with five different widths, i.e., 20 μm, 40 μm, 60 μm, 80 μm, and 100 μm, were manually created using a splitting tensile apparatus respectively. The chloride diffusion in the concrete with a certain crack was then studied under four different hydrostatic pressures of 0 MPa, 0.1 MPa, 0.3 MPa, and 0.5 MPa. Experimental results show that the chloride diffusion in concrete with a crack greatly relies on both the hydrostatic pressure and the crack width. The chloride concentration increases as the hydrostatic pressure grows, particularly for the wider cracks with width ranging from 60 μm to 100 μm. Surprisingly, the hydrostatic pressure has a negligible effect on the chloride distribution in the concrete with a crack width no larger than 40 μm. Both the chloride diffusion coefficient and the surface chloride concentration of concrete increased gradually as the hydrostatic pressure increased. The experimental findings enrich our understanding of the behavior of pre-cracked concrete when exposed to chloride-induced corrosion at different depths of marine environments.

Aim: The aim of the paper is to assess the usefulness of sectoral means in financial analyses of enterprises. Research methods: The article uses an inductive-deductive approach to assess the suitability of sectoral means used in analyses of financial standings of enterprises. The method of analysis and logical construction was used for literature review. The methods of descriptive statistics such as, arithmetic means, standard deviation and coefficient of variation were used in order to analyze the data and draw conclusions based on the results. Contribution: The assessment of the usefulness of sectoral means in the context of their variability seems to be a crucial aspect for the analysis of a company’s financial situation. When assessing the financial standing of an enterprise, it is necessary to use a comparative analysis method, based on, inter alia, a comparison in space. This type of comparison requires the use of sectoral means, whose assessment is extremely important to drawing reliable and correct conclusions of the financial situation of a company.

In the interaction of the rolling stock and the upper structure of the railway track, intense dynamic loads occur. They have a destructive effect both on the parts of the rolling stock and on the elements of the superstructure of the track. In order to develop a durable, rational and reliably functioning design of cars and locomotives with good dynamic properties and good indicators of the impact of rolling stock on the railway track, along with theoretical computational studies, experimental studies are also required, which are usually the final stage in the design and implementation of rolling stock or modernization of existing ones. Locomotives and wagons in order to improve their strength and dynamic performance. The article presents the results of field tests to determine the dynamic performance of the type CKD6e diesel locomotive. The description of the preparation of the CKD6e shunting locomotive for testing is given. An analysis of the dynamic performance of a diesel locomotive during the passage of turnouts, on a straight section of the track and in a curve with a radius of 400 m, was carried out. The studies performed showed that the minimum value of the stability factor against wheel derailment on a straight section of the track is significantly higher than the standard value. The experimentally obtained ratio of frame forces to the static load from the wheelset on the rails, the coefficients of vertical dynamics of the first and second stages of suspension and the coefficient of stability against derailment of the wheel from the rail, registered on the track section in a curve with a radius of 400 m) meet the current requirements. A calculation scheme and equations of vertical oscillations are proposed, an analysis is carried out according to the graphs of movements of bogies and a locomotive body when moving along irregularities of different lengths at different speeds.

Background: Early identification and prevention of hypoxic ischemic encephalopathy (HIE) may reduce neonatal mortality and morbidity. Objective: We aimed to correlate between urinary Activin-A and MRI (conventional and Diffusion-weighted) and the severity of HIE in full-term neonates. Methods: Forty-five full-term neonates with HIE admitted to NICU and 15 normal neonates were enrolled into the study. The concentration of urinary Activin-A was determined using enzyme immunoassay kits and MRI were done. Correlations between urinary Activin-A and MRI with the degree of HIE were done. Results: Urinary Activin-A levels were significantly higher in neonates with HIE than controls (P<0.001). It was positively correlated with the clinical grading of HIE and a cutoff value of 0.08µg/l on day-1 after birth had a sensitivity of 98.6% and specificity of 97.1% for prediction of HIE. DW-MRI detected HIE with a high sensitivity (85%) compared to the low sensitivity of conventional MRI (35%). An ADC value of ≤ 0.8 was the best sensitivity-specificity cutoff point for detecting severe ischemic injury. DW-MRI imaging was positively correlated with Urinary Activin-A and both of them were positively correlated with the clinical grades of HIE (P < 0.001). Conclusions: DW-MRI imaging is correlated well with urinary Activin-A in full-term neonates with HIE and both of them are correlated with the degree of HIE. Early determination of urinary Activin-A combined with DW-MRI imaging can early detect HIE and its severity in full-term neonates with HIE.

In this paper, we study nonlocal problems for a fractional diffusion equation and a degenerate hyperbolic equation with singular coefficients in the lower terms. The uniqueness of the solution to the problem is proved by the method of energy integrals. The existence of a solution is equivalently reduced to the question of the solvability of Volterra integral equations of the second kind and a fractional differential equation. For a particular solution of the proposed problem, its visualization is carried out for various values of the order of the fractional derivative. It is shown that the order of the derivative affects the intensity of the diffusion process (subdiffusion), as well as the shape of the wave front.

Authors evaluated the relevant literature related to the purging which is the interaction between selection and inbreeding where the population may get rid of its inbreeding load at least partially. The backroad of the relevant theory was given and the available methods were described both based on the conventional quantitative genetic approach (based on genealogy data) and based on the latest genomic methods. The different parameters necessary for signalling purging (highlighting those inbreeding coefficients which are not yet been widely known in animal and veterinary science) were presented together with the relevant results of the literature. The available statistical methods together with the softwares and R packages to calculate various inbreeding coefficients and to determine inbreeding depression and purging were provided. The main results of the different approaches obtained in laboratory ZOO and domesticated populations (lethal equivalents, ancestral inbreeding, Inbreeding-Purging Model, genomic approaches) were summarized and presented. Application possibilities and future prospective of purging was also discussed.

The ongoing outbreak of the novel coronavirus pneumonia (also known as COVID-19) has triggered a series of stringent control measures in China, such as city closure, traffic restrictions, contact tracing and household quarantine. These containment efforts often lead to changes in the contact pattern among individuals of the population. Many existing compartmental epidemic models fail to account for the effects of contact structure. In this paper, we devised a pairwise epidemic model to analyze the COVID-19 outbreak in China based on confirmed cases reported during the period February 3rd--17th, 2020. By explicitly incorporating the effects of family clusters and contact tracing followed by household quarantine and isolation, our model provides a good fit to the trajectory of COVID-19 infections and is useful to predict the epidemic trend. We obtained the average of the reproduction number $R=1.494$ ($95\%$ CI: $1.483-1.507$) for Hubei province and $R=1.178$ ($95\%$ CI: $1.145-1.158$) for China (except Hubei), suggesting that some existing studies may have overestimated the reproduction number by neglecting the dynamical correlations and clustering effects. We forecasted that the COVID-19 epidemic would peak on February 13th ($95\%$ CI: February $9-17$th) in Hubei and 6 days eariler in the regions outside Hubei. Moreover the epidemic was expected to last until the middle of March in China (except Hubei) and late April in Hubei. The sensitivity analysis shows that ongoing exposure for the susceptible and population clustering play an important role in the disease propagation. With the enforcement of household quarantine measures, the reproduction number $R$ effectively reduces and epidemic quantities decrease accordingly. Furthermore, we gave an answer to the public concern on how long the stringent containment strategies should maintain. Through numerical analysis, we suggested that the time for the resumption of work and production in China (except Hubei) and Hubei would be the middle of March and the end of April, 2020, respectively. These constructive suggestions may bring some immeasurable social-economic benefits in the long run.

The paper combines two new original concepts about eco-energetic systems. The first one is related to the M.E.N. (Mega-Eco-Nega-Watt) paradigm, which is based on three different but complementary ecological economic spaces: MEGAWATT, as needed energy, ECOWATT, as ecological energy, and NEGAWATT, as preserved energy, even the renewable energies and technologies, in the context of electrical energy production. The second concept presented in this paper is the eco-energetic efficiency, introduced in order to facilitate a correlation between the energetic efficiency of the system and a necessary, new defined ecological coefficient. The proposed formula for eco-energetic efficiency enables an interesting form of reporting to the different situations in which the input energy, output energy, lost energy and externalities, involved in an energetic process interact to produce energy in a specific energetic system, in connection with the circular economy model. Finally, is presented an original diagram of the energetic chains to produce electricity in a resilience regim, with high eco-energetic efficiency from originating in different primary energetic sources as external (gravitation & solar sources), fuels (classical & radioactive), internal sources and others. Even what kind of energetic sources are used to obtain electricity, as coals, gas, wood, hydropower, nuclear power, wind power, biomass, solar systems, and others, the entire process should be sustainable in what is the transdisciplinary integration of the different representative spheres as energy, socio-economy, ecology (environment), with the main core, sustainable education, inclueding the law and administrative aspects, as necessary fields of the knowledge based society/economy.

Background: Malaria is one of the most common diseased conditions across most developing countries caused by one of four species of Plasmodium. P. falciparum and P.vivax are the main agents responsible for malaria in Nigeria. Malarial infection has been shown to be associated with abnormalities in fluids, electrolytes and acid base balances. Electrolyte imbalance and mineral disturbances are majorly identified clinical symptoms in various infectious diseases including malaria. Electrolyte imbalance in malarial infection is capable of enhancing disease severity. The aim of this study was to investigate the effects of malarial infection on electrolytes parameters. Methods: Finger prick blood samples, Thick and Thin Giemsa-stained blood smears, were collected from 100 malaria-suspected individuals representing all age groups. The Giemsa-stained blood smears were examined microscopically. Demographic information was obtained using structured questionnaires. The electrolytes levels (Na, K, Cl^- and HCO_3-) in malarial patients were analyzed using standard procedures, Pearson's Correlation Coefficient correlation technique was used to investigate the relationship, and the strength of association between the variables. Results: The mean bound of patients’ sodium level was observed to fall within the specified normal limits of 125mmol/L – 145mmol/L; except for positive malaria patients belonging to the MP-(++) which will fall below the 125mmol/L (i.e. 126.25mmol/L – 1.77mmol/L = 124.48mmol/L). The spread of the sodium data taken from the patients were observed to fall within the normal limits leaving only the boxplot’s lower whisker out, that is, observations falling within the first quartile, except for MP-(++) patients with observations in the first to second quartile spreading outside the normal lower limit, in contrast for the negative tested patients, the box and its whiskers were almost engulfed within the normal limits. Conclusion: In our study we found that Plasmodium falciparum altered more in electrolytes parameters than Plasmodium vivax. The biochemical markers can be used as biomarkers to confirmation of malaria. This study discovered a significant linear relationship based on the Pearson product-moment correlation between creatinine and urea, potassium and chloride, potassium and creatinine, potassium and urea. The mean sodium and chloride level of positive malaria [MP-(++)] patients were observed to fall outside the normal limit.

Colostrum is a natural product, issued by both mammals and humans in first week of lactation. Among different species, donkey colostrum is considered as having, besides a valuable composition in nutrients and immune factors, an outstanding similitude with human colostrum. In this context, and taking into account the scarcity of available data concerning the interaction between climate factors and colostrum quality, a trial was conducted aiming to identify the possible influence of environmental factors on donkey colostrum nutritional traits. A stock of 16 jennies from 2 farms located in the County of Cluj, during a 7 days postpartum period was analyzed. During experimental period the daily temperature, humidity, and wind velocity data were collected. Strong positive correlations may be reported between fat and lactose, and fat and protein respectively, while moderate to strong correlation is emphasized between lactose and protein content of donkey colostrum. Testing the influence of environmental temperature, relative humidity, and wind velocity influence upon nutritional content of donkey colostrum, results the neglectable influence of the wind velocity, the negative influence of the heat stress upon all studied colostrum components, and complex influence of relative humidity, which has positive influence on fat and lactose increase when it increases, while its increase has negative influence on protein content of donkey colostrum.

This research explores how regional socioeconomic variables affect the perception of social trust and support networks (PYCC) in Italian regions, and examines the implications for public policy designed to strengthen social cohesion. This study examines the variable "People You Can Count On" (PYCC) from the ISTAT-BES dataset, focusing on its distribution across Italian regions between 2013 and 2022. Using clustering through a k-Means algorithm optimized with the Silhouette coefficient and the Elbow method, three distinct clusters of regions emerged, highlighting significant differences in social support networks. An econometric model was employed to estimate the PYCC variable, factoring in socioeconomic indicators such as employment rates, income inequality, and social participation. The results indicate a complex interplay between socioeconomic conditions and social trust, with regions in the South and Islands showing increased community support, while many Northern regions experienced declines. The study suggests that areas with lower economic conditions often foster stronger social networks, driven by necessity. These findings underline the importance of targeted public policies aimed at fostering social cohesion, particularly in regions facing economic challenges. Policy implications include enhancing education, supporting small enterprises, and promoting social housing and welfare initiatives. Strengthening community participation and volunteering are also highlighted as critical strategies to build resilient support networks. Overall, the research provides valuable insights into the regional disparities of social trust and the role of socioeconomic factors in shaping community support across Italy.

This article describes the methodology used to identify the mathematical model that describes the correlations between the input parameters of an experiment and the parameters being followed. As a technological process, the aerodynamic separation was chosen, respectively, the behavior of a solid particle within an ascending vertical airflow. The experimental data obtained were used to identify two parameters, the average linear velocity, and the angular velocity, and through the Table Curve 3D program was developed a mathematical model which describes the dependence between the input parameters (the shape and size of the solid particle and the velocity of the airflow) and the monitored parameters. In order to determine a single mathematical equation that describes as accurately as possible the correlation between the input variables and those obtained, a pyramid-type analysis was designed. The determination of the mathematical equation started from the number of equations generated by the Table Curve 3D program, then the equations with a correlation coefficient greater than 0.85 were chosen, and finally, the common equations were identified. Respecting the working methodology was identified one equation which has for the average linear velocity a correlation coefficient r2 between 0.88-0.99 and 0.86-0.99 for the angular velocity.

In this paper, the nanoscale dissipative mechanisms of a Cu pad in a Ball Grid Array (BGA) packaging structure during isothermal ageing and uniaxial tension were investigated by the molecular dynamics (MD) method and experiments. From the result of the isothermal ageing test, a nonuniform consumption of Cu and large amount of Kirkendall voids were observed at the interface of Cu and Cu₃Sn. To study the effect of pressure and orientation on this phenomenon, MD simulations were conducted on four types of Cu-Cu₃Sn interface structures with different orientations of Cu. By comparing the diffusion coefficients of atoms in those cases, it was found that the tensile stress would inhibit the diffusion of atoms, whereas compressive stress would accelerate it, and this would be more significant under a larger magnitude of stress and temperature. Note that, in the model with the (101) surface Cu at the interface, both Cu and Cu₃Sn have a higher diffusion coefficient compared with the model with (001) surface Cu. Thus, the orientation of Cu will also contribute to the uniform consumption of the pad. Uniaxial tension simulation combined with DXA and CSP analyses on those models also shows the model with (001) surface Cu has a greater mechanical reliability in our simulations and related experiments.

The flow field around a delta wing is substantially altered by the impact of the active flow control technique. The present study involves the sharp-edged delta wing of 65 deg sweep angle with different active flow control configurations. The blowing was employed as an active flow control method on the top surface of the delta wing. The various configurations considered are the baseline delta wing, delta wing with blowing holes located at 1.62%, 3.24% and 4.86% of root chord from the leading edge to the centre of the blowing holes. The computation is performed using the commercial software ANSYS Fluent. Unsteady, incompressible Reynolds-averaged Navier-Stokes equation and the shear-stress transport k-ω turbulence model are employed. The angles of attack varied in the range of 0^o < α < 35^o and Reynolds number is 2.64 x10⁶ and the jet momentum coefficient is fixed at 0.05. The blowing of air from the injection region enhances the strength of the leading-edge vortices resulting in the delay of the vortex breakdown. The performance of the delta wing is greatly improved while using the blowing method specifically for the blowing holes located at 3.24% of root chord from the leading edge as compared to without the blowing method.

CO2 flooding stands as a pivotal technique for significantly enhancing oil recovery in low-permeability reservoirs. The movement and sweeping rules at the front of CO2 flooding play a critical role in its oil recovery, yet a comprehensive quantitative analysis remains an area in need of refinement. In this study, we have developed 1D and 2D numerical simulation models to explore the sweeping behavior of miscible, immiscible, and partly-miscible CO2 flooding patterns. The front position and movement rules of the three CO2 flooding patterns are determined. A novel approach of the contour area calculation method is introduced to quantitatively characterize the sweep coefficients, and the sweeping rules are discussed regarding geological parameters, oil viscosity, and injection-production parameters. Furthermore, the Random Forest (RF) algorithm is employed to identify the controlling factor of the sweep coefficient, as determined by out-of-bag (OOB) data displacement analysis. The results show that the miscible front is located at the point of maximum CO2 content in the oil phase. The immiscible front occurs at the point of maximum interfacial tension near the production well. Remarkably, the immiscible front moves at a faster rate compared to the miscible front. Geological parameters, including porosity, permeability, and reservoir thickness, significantly impact the gravity segregation effect, thereby influencing the CO2 sweep coefficient. Immiscible flooding exhibits the highest degree of gravity segregation, with a maximum gravity segregation degree (GSD) reaching 78.1. The permeability ratio is a crucial factor, with a lower limit of approximately 5.0 for reservoirs suitable for CO2 flooding. Injection-production parameters also play a pivotal role in sweep coefficient. Decreased well spacing and increased gas injection rates are found to enhance sweep coefficients by suppressing gravity segregation. Additionally, higher gas injection rates can improve the miscibility degree of partly-miscible flooding from 0.69 to 1.0. Oil viscosity proves to be a significant factor influencing the sweep coefficients, with high seepage resistance due to increasing oil viscosity dominating the miscible and partly-miscible flooding patterns. Conversely, gravity segregation primarily governs the sweep coefficient in immiscible flooding. In terms of controlling factors, the permeability ratio emerges as a paramount influence, with a factor importance value (FI) reaching 1.04. these results provide a theoretical foundation for the application of CO2 flooding, enhancing the understanding of the critical factors governing its success.

In the Cerrado-Amazonian ecotone in the State of Mato Grosso, intensely altered by anthropic action, the knowledge and processes of energy conversion and energy balance are still incipient, making the monitoring and modeling of diffuse radiation essential for several applications. The objective of this study was to evaluate the seasonality of the diurnal evolution and estimate the hourly diffuse radiation (Hdh) incident radiation in the horizontal plane, between June 2011 and October de 2016. The instantaneous measurements (5 minutes) of diffuse radiation underwent geometric, astronomical, and anisotropic corrections, with subsequent hourly integrations. The seasonality of diffuse radiation and its radiometric fractions was evaluated. The estimates were made considering total and seasonal data groupings (water stations in the region) and in different cloudiness classes (atmospheric transmissivity index - KTh). The diurnal behavior of diffuse radiation (Hdh) was similar to that of global radiation and at the top of the atmosphere, with maximum values at solar noon. The correlations between Kdh and KTh showed third-order polynomial behavior, with maximum observed values of Kdh ranging from 0.8 to 0.9, for KTh less than 0.2. Estimation equations based on radiometric fractions underestimated the values of diffuse radiation, with a better performance presented by models adjusted in annual data groupings. Among the parameterized models for estimating diffuse radiation obtained in the literature, those calibrated regionally in this study, together with those developed for tropical regions, presented better statistical performances.

Satellite measurements are one of the main sources of data on the state of the marine environment. To obtain information about the sea brightness coefficient , it is needed to correctly carry out atmospheric correction. In the presence of dust aerosol over the Black Sea, physically incorrect values of the spectral brightness coefficient often occur, and specifically negative values in the IR region of the spectrum. The main objective of the study is to evaluate the influence of dust aerosol on the spectral dependence of sea brightness, based on analytical calculations from the transfer theory using the principle of plane-parallel layers and results of validation of AERONET-OC field and remote sensing data. The work analyzes spectral dependence of the first error eigenvector of the standard atmospheric correction in the presence of dust aerosol. As result it is given that with an absorbing aerosol, the atmospheric correction error is described by the spectral course of molecular scattering, i.e. close to

The importance of irrigation in boosting agricultural production and productivity is widely understood. Proper planning and effective and efficient management and operation of irrigation system require crop and site-specific data. Since the last few years, Ethiopia has embarked on expansion of irrigated wheat. However, crop-specific data useful for irrigation planning and management for wheat crop is limited. The objective of this research was to determine water requirements and crop coefficients for wheat crops based on field measurements. The research was carried out at the Debre Zeit Agricultural Research Center in central Ethiopia during the dry season (Bega) of 2021/22. The crop considered for the experiment was durum wheat of the Utuba variety. Two non-weighing lysimeter units were employed to measure the water balance components. The soil moisture was monitored using gravimetric method on daily basis conducted both before and after each irrigation event at various depth intervals. The crop required a total of 115 days to fully mature. The length of the growth of initial, development, mid, and late stages were about 20, 30, 42, and 23 days, respectively. Microsoft Excel was used for the data analysis and the CropWAT8.0 model to estimate the reference evapotranspiration. Crop evapotranspiration (ETc) was determined using the water balance equation, and crop coefficients were computed from ETc and reference evapotranspiration (ETo). The results indicate that the total seasonal water requirement of the crop was 392.75mm. The growth stage-based water requirement was 40.35 mm, 82.44 mm, 238.66 mm, and 31.3 mm during the initial, development, mid, and late growing stages, respectively. For the initial, development, mid, and late stages of wheat growth, the crop coefficient was calculated to be 0.51, 0.83, 1.29, and 0.52, respectively. It was found that a fourth-degree polynomial equation fits well and explains the relationship between day of growth stage and kc of the crop. Although a one-season measurement, the results generated here could be useful for crop-specific data in scarce areas.

The study of the optical properties of biological tissues for a wide spectral range is necessary for the development and planning of noninvasive optical methods to be used in clinical practice. In this study, we propose a new method to calculate almost all optical properties of tissues as a function of wavelength directly from spectral measurements. Using this method and with the exception of the reduced scattering coefficient, which was obtained by traditional simulation methods, all the other optical properties were calculated in a simple and fast manner for human and pathological colorectal tissues. The obtained results are in good agreement with previous published data, both in magnitude and in wavelength dependence. Since this method is based on spectral measurements and not on discrete-wavelength experimental data, the calculated optical properties contain spectral signatures that correspond to major tissue chromophores such as DNA and hemoglobin. Analysis of the absorption bands of hemoglobin in the wavelength dependence of the absorption spectra of normal and pathological colorectal mucosa allowed to identify differentiated accumulation of a pigment in these tissues. The increased content of this pigment in the pathological mucosa may be used for the future development of noninvasive diagnostic methods for colorectal cancer detection.

Free volume is an extremely important intrinsic defect in polymers. Structurally, the free volume is the randomly distributed holes in the polymer molecular chain segments. From the perspective of molecular movement, it is also the space needed for the movement of molecular segments. In proton exchange membrane fuel cells, the free volume is also the space needed for the directional conduction of protons. Irradiation grafting sulfonated polyvinylidene fluoride (PVDF) is one of the methods to produce proton exchange membrane with good proton channel rate. Using the LYS-1 program, based on the linear absorption coefficient and backscatter coefficient models, the percentage of annihilated positrons in PVDF in the two-layer model and the three-layer model was studied, and comparing the two fitting results it is determined that the model closest to the positron annihilation percentage required by the PALS experiment is the two-layer model, which allows the percentage of positrons that are annihilated in PVDF films with a thickness of 100 μm to reach 46% using the high energy positron source ⁴⁴Ti without using the positron moderator. Using positron annihilation lifetime spectrum (PALS) analysis methods, based on Eldrup's classical model of free volume, the influence of absorbed doses of α particles on the free volume and crystallinity of PVDF was investigated, respectively. Based on the two test results the model of cross-linking and degradation of polyvinylidene fluoride irradiated by α particles was determined. Afterwards, X-ray diffraction (XRD) methods was used to study the change of PVDF crystal area before and after irradiation. The XRD results are consistent with the results measured by PALS.

In this paper described numerical expansion of natural-valued power function xⁿ, in point x = x_0, where n; x₀ - positive integers. Applying numerical methods, the calculus of nite dierences, particular pattern, that is sequence A287326 in OEIS, which shows the expansion of perfect cube n as row sum over k; 0 ≤ k ≤ n − 1 is generalized, obtained results are applied to show expansion of monomial n^2m+1; m = 0; 1; 2; ..., N. Additionally, relation between Faulhaber's sum ∑_n^m and nite dierences of power are shown in section 4.

Complex modeling has received significant attention in recent years and is increasingly used to explain the statistical phenomenon with increasing and decreasing fluctuations such as the similarity or difference of spike protein charge patterns of coronaviruses. Different from the existing covariance or correlation coefficient methods in traditional integer dimension construction, this study proposes a simplified novel fractional dimension derivation with the exact Excel tool algorithm. It involves the fractional center moment extension to covariance, which ends up a complex covariance coefficient that is better than the Pearson correlation coefficient, in the sense that the nonlinearity relationship can be further depicted. The spike protein sequences of coronaviruses were obtained from the GenBank and GISAID database, including the coronaviruses from pangolin, bat, canine, swine (three variants), feline, tiger, SARS-CoV-1, MERS, and SARS-CoV-2 (including the strains of Wuhan, Beijing, New York, German, and UK variant B.1.1.7) were used as the representative examples in this study. By examining the values above and below the average/mean based on the positive and negative charge patterns of the amino acid residues of the spike proteins from coronaviruses, the proposed algorithm provides deep insights into the nonlinear evolving trends of spike proteins for understanding the viral evolution and identifying the protein characteristics associated with viral fatality. The calculation results demonstrate that the complex covariance coefficient analyzed by this algorithm is capable of distinguishing the subtle nonlinear differences in the spike protein charge patterns with reference to Wuhan strain SARS-CoV-2 for which the Pearson correlation coefficient may overlook. Our analysis reveals the unique convergent (positive correlative) to divergent (negative correlative) domain center positions of each virus. The convergent or conserved region may be critical to the viral stability or viability; while the divergent region is highly variable between coronaviruses suggesting high frequency of mutations in this region. The analyses show that the conserved center region of SARS-CoV-1 spike protein is located at amino acid residues 900, but shifted to the amino acid residues 700 in MERS spike protein, and then to amino acid residues 600 in SARS-COV-2 spike protein, indicating the evolvement of the coronaviruses. Interestingly, the conserved center region of the spike protein in SARS-COV-2 variant B.1.1.7 shifted back to amino acid residues 700, suggesting this variant is more virulent than the original SARS-COV-2 strain. Another important characteristic our study reveals is that the distance between the divergent mean and the maximal divergent point in each of the viruses (MERS>SARS-CoV-1>SARS-CoV-2) is proportional to viral fatality rate. This algorithm may help to understand and analyze the evolving trends and critical characteristics of SARS-COV-2 variants, other coronaviral proteins and viruses.

The application of a commonly used computer algorithm based on the group-additivity method for the calculation of the liquid viscosity coefficient at 292.15K and the activity coefficient at infinite dilution in water at 298.15K of organic molecules is presented. The method is based on the complete breakdown of the molecules into their constituting atoms, further subdividing them by their immediate neighbourhood. A fast Gauss-Seidel fitting method using experimental data from literature is applied for the calculation of the atom groups’ contributions. Plausibility tests have been carried out on each of the calculations using a 10-fold cross-validation procedure which confirms the excellent predictive quality of the method. The goodness of fit (Q²) and the standard deviation (σ) of the cross-validation calculations for the viscosity coefficient, expressed as log(η), was 0.9728 and 0.11, respectively, for 413 test molecules, and for the activity coefficient log(γ)^∞ the corresponding values were 0.9736 and 0.31, respectively, for 621 test compounds. The present approach has proven its versatility in that it enabled at once the evaluation of the liquid viscosity of normal organic compounds as well as of ionic liquids.

Over the last decades, an important number of regional and global Digital Elevation Models (DEMs) have been released publicly. As a consequence, researchers need to choose between several of these models to perform their studies and to use these DEMs as third-party data to compute derived products (e.g., for orthorectification). However, the comparison of DEMs is not trivial. For most quantitative comparisons, DEMs require to be expressed in the same Coordinate Reference System (CRS), sampled over the same grid (i.e., be at the same ground sampling distance with the same pixel-is-area or pixel-is-point convention), and with heights relative to the same Vertical Reference System (VRS). Thankfully, many open tools allow us to perform these transformations precisely and easily. Despite these rigorous transformations, local or global planimetric displacements may still be observed from one DEM to another. These displacements, or disparities, may lead to significant biases in comparisons of DEM elevations or derived products such as slope, aspect or curvature. Therefore, the control of DEM planimetric accuracy is certainly the most important task to perform at first before any comparison. This paper presents the disparity analysis method enhanced to achieve a sub-pixel accuracy, by interpolating the linear regression coefficients computed within an exploration window. This new method is significantly faster than oversampling the input data because it uses the correlation coefficients that have been already computed in the disparity analysis. To demonstrate the robustness of this algorithm, artificial displacements have been performed in a 11x11 grid with a 0.1-pixel step in both directions. The Copernicus DEM GLO-30 has been interpolated by a “classical” bicubic to achieve these 11x11 displacements. This validation method has been applied in four 10 km x 10 km DEMIX tiles showing different height distributions. Globally, this new sub-pixel accuracy method is robust. Artificial displacements have been retrieved with with typical errors (e_b) ranging from 12 to 20 % of the pixel size (worst case in Croatia).These errors in displacement retrievals are not constant in the 11x11 grid and the overall error E_b depends on the roughness (altimetry variations) encountered in the different tiles. The second idea of this paper is to assess the impact of the bicubic parameter (slope of the weight function at a distance d=1 of the interpolated point) on the accuracy of the displacement retrieval. By considering E_b as a quality indicator, tests have been performed in the four DEMIX tiles making the bicubic parameter vary between -1.5 and 0.0 by step of 0.1. For each DEMIX tile, the best bicubic (BBC) parameter b* is interpolated from the four E_b minimal values. This BBC parameter b* is low for flat areas (around -0.95) and higher in mountainous areas (around -0.75). The roughness indicator is the standard deviation of the slope norms computed from all the pixels of a tile. A logarithmic regression analysis performed between the roughness indicator and the BBC parameter b* computed in 67 DEMIX tiles shows a high correlation (r=0.717). The logarithmic regression formula estimating the BBC parameter from the roughness indicator is generic and may be applied to estimate the displacements between two different DEMs. This formula may also be used to set up a future Adaptative Best BiCubic (ABBC) that will estimate the local roughness in a sliding window to compute a local BBC.

This paper proposes a model based on gene expression programming for predicting discharge coefficient of triangular labyrinth weirs. The parameters influencing discharge coefficient prediction were first examined and presented as crest height ratio to the head over the crest of the weir (p/y), crest length of water to channel width (L/W), crest length of water to the head over the crest of the weir (L/y), Froude number (F=V/√(gy)) and vertex angle () dimensionless parameters. Different models were then presented using sensitivity analysis in order to examine each of the dimensionless parameters presented in this study. In addition, an equation was presented through the use of nonlinear regression (NLR) for the purpose of comparison with GEP. The results of the studies conducted by using different statistical indexes indicated that GEP is more capable than NLR. This is to the extent that GEP predicts the discharge coefficient with an average relative error of approximately 2.5% in such a manner that the predicted values have less than 5% relative error in the worst model.

Osteoconductive granulated biopolymers (OGB) are used to restore the lost volume of the jaw bone. OGB is employed as a loose fraction and exhibits physical traits common to bulk mixtures. By removing air bubbles and industrial dust from the OGB fraction through special processing, more accessible spaces are left over for the adsorption of bone growth factors. The recipient site's biological environment alters the OGB fraction's physical characteristics. This is the cause of the OGB fraction's volume changing uncontrollably during the first three weeks following surgery. Predictive indicators for describing the physical processes of osteoconduction include the compaction coefficient and adsorption capacity. Taking into account the prognostic indicators of the dynamics of changes in the physical properties of the OGB fraction in the postoperative period, 3D planning of the bioengineered structure should be done. The OGB fraction's adsorption and drainage properties are optimized by raising the purity of OGB production and preparing the biopolymer for clinical studies.

The emergence of electric vehicles has brought new issues such as the problem of rolling element bearings (REBs) operating at high speeds. Losses due to these components in mechanical transmissions are a key issue and must therefore be taken into account right from the design stage of these systems. Among these losses, the one induced by the motion of rolling elements , known as drag loss, becomes predominant in high-speed REBs. Although an experimental approach is still possible, it is difficult to isolate this loss in order to study it properly. A numerical approach based on CFD is therefore a possible way forward, even if other issues arise. The aim of this article is to study the ability of such an approach to correctly estimate the drag coefficient associated with the motion of rolling elements. The influence of the numerical domain extension, the mesh refinement, the simplification of the ring shape and the presence of the cage, on the values of the drag coefficient is presented. While it seems possible to compromise on the calculation domain and mesh size, it appears that the other parameters must be taken into account as much as possible to obtain realistic results.

In this paper we derived an expression that allows the determination of the thermo-optic coefficient of weakly-guiding germanium-doped silica fibers, based on the thermal behavior of optical fiber devices, such as, fiber Bragg gratings (FBGs). The calculations rely on the full knowledge of the fiber parameters and on the temperature sensitivity of FBGs. In order to validate the results, we estimated the thermo-optic coefficient of bulk GeO2 glass at 293 K and 1.55 m to be 18.3x10-6 K-1. The determination of this value required to calculate a correction factor which is based on the knowledge of the thermal expansion coefficient of the fiber core, the Pockels’ coefficients (p11=0.125, p12=0.258 and p44=-0.0662) and the Poisson ratio (=0.161) of the SMF-28 fiber. To achieve that goal, we estimated the temperature dependence of the thermal expansion coefficient of GeO2 and we discussed the dispersion and temperature dependence of Pockels’ coefficients. We have presented expressions for the dependence of the longitudinal and transverse acoustic velocities on the GeO2 concentration used to calculate the Poisson ratio. We have also discussed the dispersion of the photoelastic constant. An estimate for the temperature dependence of the thermo-optic coefficient of bulk GeO2 glass is presented for the 200-300 K temperature range.